include/configs: Use new CONFIG_CMD_* in various [TUVWZYZ]* named board config files.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

include/configs/TASREG.h

@@ -50,20 +50,25 @@
 
 #undef CONFIG_MONITOR_IS_IN_RAM	              /* no pre-loader required!!! ;-) */
 
-#define CONFIG_COMMANDS	      ((CONFIG_CMD_DFL        |    \
-				CFG_CMD_BSP           |    \
-				CFG_CMD_EEPROM        |    \
-				CFG_CMD_I2C            ) & \
-			       ~(CFG_CMD_NET))
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+
+#undef CONFIG_CMD_NET
+
+
 #define CONFIG_BOOTDELAY	3
 
 #define CFG_PROMPT		"=> "
 #define CFG_LONGHELP				/* undef to save memory		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/

include/configs/TOP860.h

@@ -107,30 +107,28 @@
  */
 #define CFG_MATCH_PARTIAL_CMD
 
+
 /*
- * List of available monitor commands.  Use the system default list
- * plus add some of the "non-standard" commands back in.
- * See ./cmd_confdefs.h
- */
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-								CFG_CMD_ASKENV	| \
-								CFG_CMD_DHCP	| \
-								CFG_CMD_I2C		| \
-								CFG_CMD_EEPROM	| \
-								CFG_CMD_REGINFO	| \
-								CFG_CMD_IMMAP	| \
-								CFG_CMD_ELF		| \
-								CFG_CMD_DATE	| \
-								CFG_CMD_MII 	| \
-								CFG_CMD_BEDBUG	\
-						      )
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_BEDBUG
+
 
 #define	CONFIG_AUTOSCRIPT		1
 #define	CFG_LOADS_BAUD_CHANGE	1
 #undef	CONFIG_LOADS_ECHO			/* NO echo on for serial download	*/
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
 
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
@@ -141,7 +139,7 @@
  #define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
  #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
  #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -239,7 +237,7 @@
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
 #endif
 

include/configs/VCMA9.h

@@ -48,27 +48,24 @@
 #define CONFIG_SETUP_MEMORY_TAGS 1
 #define CONFIG_INITRD_TAG	 1
 
-/***********************************************************
- * Command definition
- ***********************************************************/
-#define CONFIG_COMMANDS \
-			(CONFIG_CMD_DFL	 | \
-			CFG_CMD_CACHE	 | \
-			/*CFG_CMD_JFFS2	 |*/ \
-			/*CFG_CMD_NAND	 |*/ \
-			CFG_CMD_EEPROM	 | \
-			CFG_CMD_I2C	 | \
-			CFG_CMD_USB	 | \
-			CFG_CMD_REGINFO  | \
-			CFG_CMD_FAT	 | \
-			CFG_CMD_DATE	 | \
-			CFG_CMD_ELF	 | \
-			CFG_CMD_DHCP	 | \
-			CFG_CMD_PING	 | \
-			CFG_CMD_BSP)
-
-/* this must be included after the definiton of CONFIG_COMMANDS */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_BSP
+
 
 #define CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2 "> "
@@ -145,7 +142,7 @@
 #define CONFIG_IPADDR		10.0.0.110
 #define CONFIG_SERVERIP		10.0.0.1
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	115200		/* speed to run kgdb serial port */
 /* what's this ? it's not used anywhere */
 #define CONFIG_KGDB_SER_INDEX	1		/* which serial port to use */
@@ -246,7 +243,7 @@
 /*-----------------------------------------------------------------------
  * NAND flash settings
  */
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 
 #define CFG_NAND_LEGACY
 #define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
@@ -280,6 +277,6 @@
 #define CONFIG_MTD_NAND_VERIFY_WRITE	1
 #define CONFIG_MTD_NAND_ECC_JFFS2	1
 
-#endif	/* CONFIG_COMMANDS & CFG_CMD_NAND */
+#endif
 
 #endif	/* __CONFIG_H */

include/configs/VOH405.h

@@ -58,28 +58,31 @@
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_IDE	| \
-				CFG_CMD_FAT	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_NAND	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM	)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 
 #define CONFIG_SUPPORT_VFAT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
@@ -98,7 +101,7 @@
 #define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -319,7 +322,7 @@
 #define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
 					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 

include/configs/VOM405.h

@@ -65,19 +65,22 @@
 				 CONFIG_BOOTP_DNS2 | \
 				 CONFIG_BOOTP_SEND_HOSTNAME )
 
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_BSP	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -96,7 +99,7 @@
 #define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -244,7 +247,7 @@
 #define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
 					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 

include/configs/VoVPN-GW.h

@@ -138,24 +138,25 @@
 
 #endif
 
-/* configure commands */
-#define CONFIG_COMMANDS		(	CFG_CMD_AUTOSCRIPT	| \
-					CFG_CMD_BDI		| \
-					CFG_CMD_CONSOLE		| \
-					CFG_CMD_ECHO		| \
-					CFG_CMD_ENV		| \
-					CFG_CMD_FLASH		| \
-					CFG_CMD_IMI		| \
-					CFG_CMD_IMLS		| \
-					CFG_CMD_LOADB		| \
-					CFG_CMD_MEMORY		| \
-					CFG_CMD_MISC		| \
-					CFG_CMD_NET		| \
-					CFG_CMD_PING		| \
-					CFG_CMD_RUN	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_IMLS
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+
 
 /*
  * boot options & environment
@@ -206,7 +207,7 @@
 #define	CFG_PROMPT			"=> "
 
 /* console i/o buffer size */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define	CFG_CBSIZE			1024
 #else
 #define	CFG_CBSIZE			256
@@ -305,7 +306,7 @@
 
 /* cache configuration */
 #define CFG_CACHELINE_SIZE		32      /* for MPC8260 */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT		5	/* log base 2 of above */
 #endif
 

include/configs/W7OLMC.h

@@ -70,13 +70,22 @@
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 
-#define CONFIG_COMMANDS		\
-	(CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_ASKENV | \
-	 CFG_CMD_DHCP | CFG_CMD_BEDBUG | CFG_CMD_DATE | CFG_CMD_I2C | \
-	 CFG_CMD_EEPROM | CFG_CMD_ELF | CFG_CMD_BSP | CFG_CMD_REGINFO)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_REGINFO
 
 #undef CONFIG_WATCHDOG				/* watchdog disabled		*/
 #define CONFIG_HW_WATCHDOG			/* HW Watchdog, board specific	*/
@@ -92,7 +101,7 @@
 #ifdef  CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2     "> "
 #endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
@@ -277,7 +286,7 @@
  */
 #define CFG_DCACHE_SIZE		8192		/* For AMCC 405 CPUs			*/
 #define CFG_CACHELINE_SIZE	32		/* ...		*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above val. */
 #endif
 
@@ -309,7 +318,7 @@
 #define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM		0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use	*/
 #endif

include/configs/W7OLMG.h

@@ -75,14 +75,25 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-#define CONFIG_COMMANDS		\
-	(CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_IRQ | CFG_CMD_ASKENV | \
-	 CFG_CMD_DHCP | CFG_CMD_BEDBUG | CFG_CMD_DATE | CFG_CMD_I2C | \
-	 CFG_CMD_EEPROM | CFG_CMD_ELF | CFG_CMD_BSP | CFG_CMD_REGINFO | \
-	 CFG_CMD_DTT)
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_DTT
+
 
 #undef CONFIG_WATCHDOG				/* watchdog disabled		*/
 #define CONFIG_HW_WATCHDOG			/* HW Watchdog, board specific	*/
@@ -98,7 +109,7 @@
 #ifdef  CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2     "> "
 #endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
@@ -278,7 +289,7 @@
  */
 #define CFG_DCACHE_SIZE		8192		/* For AMCC 405 CPUs			*/
 #define CFG_CACHELINE_SIZE	32		/* ...		*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5		/* log base 2 of the above val. */
 #endif
 
@@ -310,7 +321,7 @@
 #define BOOTFLAG_COLD		0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM		0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use	*/
 #endif

include/configs/WUH405.h

@@ -60,19 +60,22 @@
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_NAND	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -92,7 +95,7 @@
 #define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -270,7 +273,7 @@
 #define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
 					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 

include/configs/XPEDITE1K.h

@@ -182,25 +182,24 @@ extern void out32(unsigned int, unsigned long);
 #define CONFIG_HAS_ETH2		1	/* add support for "eth2addr"	*/
 #define CONFIG_HAS_ETH3		1	/* add support for "eth3addr"	*/
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_BEDBUG	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_PING | \
-				CFG_CMD_ELF | \
-				CFG_CMD_MII | \
-				CFG_CMD_DIAG | \
-				CFG_CMD_FAT )
-
-/*				CFG_CMD_DHCP	| \ */
-/*				CFG_CMD_KGDB	| \ */
-
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_FAT
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -209,7 +208,7 @@ extern void out32(unsigned int, unsigned long);
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -254,7 +253,7 @@ extern void out32(unsigned int, unsigned long);
  */
 #define CFG_DCACHE_SIZE		8192 /* For AMCC 440GX CPUs */
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 
@@ -266,7 +265,7 @@ extern void out32(unsigned int, unsigned long);
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif

include/configs/Yukon8220.h

@@ -39,12 +39,6 @@
 #define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM		0x02	/* Software reboot	*/
 
-#define CFG_CACHELINE_SIZE	32	/* For MPC8220 CPUs */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#  define CFG_CACHELINE_SHIFT	5   /* log base 2 of the above value */
-#endif
-
 /*
  * Serial console configuration
  */
@@ -70,31 +64,31 @@
 
 #define CONFIG_TIMESTAMP			/* Print image info with timestamp */
 
+
 /*
- * Supported commands
+ * Command line configuration.
  */
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_BOOTD	| \
-				CFG_CMD_CACHE	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DIAG	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_NET	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_REGINFO | \
-				CFG_CMD_SDRAM	| \
-				CFG_CMD_SNTP	)
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
+
 
 #define CONFIG_NET_MULTI
 #define CONFIG_MII
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 /*
  * Autobooting
  */
@@ -293,7 +287,7 @@
  */
 #define CFG_LONGHELP			    /* undef to save memory	*/
 #define CFG_PROMPT		"=> "	    /* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024	    /* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE		256	    /* Console I/O Buffer Size	*/
@@ -309,6 +303,11 @@
 
 #define CFG_HZ			1000	    /* decrementer freq: 1 ms ticks */
 
+#define CFG_CACHELINE_SIZE	32	/* For MPC8220 CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5   /* log base 2 of the above value */
+#endif
+
 /*
  * Various low-level settings
  */

include/configs/ZPC1900.h

@@ -106,22 +106,24 @@
 
 #define CONFIG_BAUDRATE		38400
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL   \
-				| CFG_CMD_ASKENV  \
-				| CFG_CMD_DHCP    \
-				| CFG_CMD_IMMAP   \
-				| CFG_CMD_MII     \
-				| CFG_CMD_PING    \
-				)
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
 #define CONFIG_BOOTCOMMAND	"dhcp;bootm"	/* autoboot command */
 #define CONFIG_BOOTARGS		"root=/dev/nfs rw ip=:::::eth0:dhcp"
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
 #define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
 #undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
@@ -139,7 +141,7 @@
 #define CFG_PROMPT_HUSH_PS2	"> "
 #define CFG_LONGHELP			/* undef to save memory	    */
 #define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CFG_CBSIZE		256	/* Console I/O Buffer Size  */
@@ -223,7 +225,7 @@
 #endif
 
 #define CFG_CACHELINE_SIZE	32	/* For MPC8260 CPU */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 

include/configs/ZUMA.h

@@ -106,12 +106,18 @@
 
 #define CONFIG_MII		/* enable MII commands */
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | \
-				 CFG_CMD_ASKENV | \
-				 CFG_CMD_BSP	| \
-				 CFG_CMD_JFFS2	| \
-				 CFG_CMD_MII	| \
-				 CFG_CMD_DATE)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+
 
 /*
  * JFFS2 partitions
@@ -131,15 +137,12 @@
 #define MTDPARTS_DEFAULT	"mtdparts=zuma-1:-(jffs2),zuma-2:-(user)"
 */
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -349,7 +352,7 @@
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	32	/* For all MPC74xx CPUs		 */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif