Merge branch 'master' of git://git.denx.de/u-boot-arm

MAINTAINERS

@@ -591,6 +591,10 @@ Po-Yu Chuang <ratbert@faraday-tech.com>
 
 	a320evb		FA526 (ARM920T-like) (a320 SoC)
 
+Eric Cooper <ecc@cmu.edu>
+
+	dockstar	ARM926EJS (Kirkwood SoC)
+
 George G. Davis <gdavis@mvista.com>
 
 	assabet		SA1100

arch/arm/cpu/arm1176/start.S

@@ -123,34 +123,6 @@ _bss_start_ofs:
 _bss_end_ofs:
 	.word _end - _start
 
-.globl _datarel_start_ofs
-_datarel_start_ofs:
-	.word __datarel_start - _start
-
-.globl _datarelrolocal_start_ofs
-_datarelrolocal_start_ofs:
-	.word __datarelrolocal_start - _start
-
-.globl _datarellocal_start_ofs
-_datarellocal_start_ofs:
-	.word __datarellocal_start - _start
-
-.globl _datarelro_start_ofs
-_datarelro_start_ofs:
-	.word __datarelro_start - _start
-
-.globl _rel_dyn_start_ofs
-_rel_dyn_start_ofs:
-	.word __rel_dyn_start - _start
-
-.globl _rel_dyn_end_ofs
-_rel_dyn_end_ofs:
-	.word __rel_dyn_end - _start
-
-.globl _dynsym_start_ofs
-_dynsym_start_ofs:
-	.word __dynsym_start - _start
-
 /* IRQ stack memory (calculated at run-time) + 8 bytes */
 .globl IRQ_STACK_START_IN
 IRQ_STACK_START_IN:
@@ -300,13 +272,13 @@ copy_loop:
 	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
 	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r0, [r2]	/* r0 <- location to fix up, IN FLASH! */
-	add	r0, r0, r9	/* r0 <- location to fix up in RAM */
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
 	ldr	r1, [r2, #4]
 	and	r8, r1, #0xff
-	cmp	r8, #23		/* relative fixup? */
+	cmp	r8, #23			/* relative fixup? */
 	beq	fixrel
-	cmp	r8, #2		/* absolute fixup? */
+	cmp	r8, #2			/* absolute fixup? */
 	beq	fixabs
 	/* ignore unknown type of fixup */
 	b	fixnext
@@ -315,7 +287,7 @@ fixabs:
 	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
 	add	r1, r10, r1		/* r1 <- address of symbol in table */
 	ldr	r1, [r1, #4]		/* r1 <- symbol value */
-	add	r1, r1, r9		/* r1 <- relocated sym addr */
+	add	r1, r9			/* r1 <- relocated sym addr */
 	b	fixnext
 fixrel:
 	/* relative fix: increase location by offset */
@@ -323,7 +295,7 @@ fixrel:
 	add	r1, r1, r9
 fixnext:
 	str	r1, [r0]
-	add	r2, r2, #8	/* each rel.dyn entry is 8 bytes */
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
@@ -408,6 +380,13 @@ _board_init_r_ofs:
 	.word board_init_r - _start
 #endif
 
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
+
 #ifdef CONFIG_ENABLE_MMU
 _mmu_table_base:
 	.word mmu_table

arch/arm/cpu/arm720t/start.S

@@ -81,14 +81,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -107,30 +110,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -184,9 +163,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -197,35 +175,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -242,18 +238,25 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * We are done. Do not return, instead branch to second part of board
  * initialization, now running from RAM.
  */
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
+
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
 
 /*
  *************************************************************************

arch/arm/cpu/arm720t/u-boot.lds

@@ -40,29 +40,38 @@ SECTIONS
 
 	. = ALIGN(4);
 	.data : {
-		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/arm920t/start.S

@@ -77,14 +77,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -103,30 +106,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual start code
  */
@@ -230,9 +209,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -243,35 +221,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -289,24 +285,33 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * initialization, now running from RAM.
  */
 #ifdef CONFIG_NAND_SPL
-	ldr     pc, _nand_boot
+	ldr     r0, _nand_boot_ofs
+	mov	pc, r0
 
-_nand_boot: .word nand_boot
+_nand_boot_ofs:
+	.word nand_boot
 #else
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
 #endif
 
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
+
 /*
  *************************************************************************
  *

arch/arm/cpu/arm920t/u-boot.lds

@@ -49,28 +49,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/arm925t/start.S

@@ -87,14 +87,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -113,30 +116,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -221,9 +200,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -234,35 +212,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -271,6 +267,8 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
 	cmp	r0, r1
 	bne	clbss_l
 
+	bl coloured_LED_init
+	bl red_LED_on
 #endif
 
 /*
@@ -278,24 +276,33 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * initialization, now running from RAM.
  */
 #ifdef CONFIG_NAND_SPL
-	ldr     pc, _nand_boot
+	ldr     r0, _nand_boot_ofs
+	mov	pc, r0
 
-_nand_boot: .word nand_boot
+_nand_boot_ofs:
+	.word nand_boot
 #else
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
 #endif
 
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
+
 /*
  *************************************************************************
  *

arch/arm/cpu/arm925t/u-boot.lds

@@ -44,28 +44,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/arm946es/start.S

@@ -10,6 +10,7 @@
  *  Copyright (c) 2002	Gary Jennejohn <garyj@denx.de>
  *  Copyright (c) 2003	Richard Woodruff <r-woodruff2@ti.com>
  *  Copyright (c) 2003	Kshitij <kshitij@ti.com>
+ *  Copyright (c) 2010	Albert Aribaud <albert.aribaud@free.fr>
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -71,6 +72,7 @@ _fiq:
 
 	.balignl 16,0xdeadbeef
 
+_vectors_end:
 
 /*
  *************************************************************************
@@ -91,14 +93,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -117,30 +122,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -190,9 +171,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -203,42 +183,60 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
 clbss_l:str	r2, [r0]		/* clear loop...		    */
 	add	r0, r0, #4
 	cmp	r0, r1
-	bne	clbss_l
+	blo	clbss_l
 #endif
 
 /*
@@ -250,20 +248,27 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
 
 _nand_boot: .word nand_boot
 #else
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
 #endif
 
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
+
 /*
  *************************************************************************
  *

arch/arm/cpu/arm946es/u-boot.lds

@@ -41,28 +41,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/arm_intcm/start.S

@@ -89,14 +89,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -115,30 +118,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -188,9 +167,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -201,35 +179,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -246,18 +242,33 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * We are done. Do not return, instead branch to second part of board
  * initialization, now running from RAM.
  */
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+#ifdef CONFIG_NAND_SPL
+	ldr     r0, _nand_boot_ofs
+	mov	pc, r0
+
+_nand_boot_ofs:
+	.word nand_boot
+#else
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
+#endif
+
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
 
 /*
  *************************************************************************

arch/arm/cpu/arm_intcm/u-boot.lds

@@ -41,28 +41,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/armv7/omap4/board.c

@@ -32,6 +32,8 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/sizes.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 /*
  * Routine: s_init
  * Description: Does early system init of muxing and clocks.
@@ -100,7 +102,6 @@ u32 sdram_size(void)
  */
 int dram_init(void)
 {
-	DECLARE_GLOBAL_DATA_PTR;
 
 	gd->ram_size = sdram_size();
 

arch/arm/cpu/ixp/start.S

@@ -100,14 +100,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -126,30 +129,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -314,9 +293,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -327,35 +305,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -372,19 +368,25 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * We are done. Do not return, instead branch to second part of board
  * initialization, now running from RAM.
  */
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
 
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
 
 /****************************************************************************/
 /*									    */

arch/arm/cpu/ixp/u-boot.lds

@@ -41,28 +41,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/lh7a40x/start.S

@@ -77,14 +77,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -103,30 +106,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -201,9 +180,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -214,35 +192,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -256,18 +252,25 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * We are done. Do not return, instead branch to second part of board
  * initialization, now running from RAM.
  */
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
+
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
 
 /*
  *************************************************************************

arch/arm/cpu/lh7a40x/u-boot.lds

@@ -41,28 +41,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/s3c44b0/start.S

@@ -68,14 +68,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -94,30 +97,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -173,9 +152,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -186,47 +164,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
-/*
-	now copy to sram the interrupt vector
-*/
-	adr	r0, real_vectors
-	add	r2, r0, #1024
-	ldr	r1, =0x0c000000
-	add	r1, r1, #0x08
-vector_copy_loop:
-	ldmia	r0!, {r3-r10}
-	stmia	r1!, {r3-r10}
-	cmp	r0, r2
-	blo	vector_copy_loop
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -243,18 +227,25 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * We are done. Do not return, instead branch to second part of board
  * initialization, now running from RAM.
  */
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
+
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
 
 /*
  *************************************************************************

arch/arm/cpu/s3c44b0/u-boot.lds

@@ -41,28 +41,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

arch/arm/cpu/sa1100/start.S

@@ -78,14 +78,17 @@ _TEXT_BASE:
 
 /*
  * These are defined in the board-specific linker script.
+ * Subtracting _start from them lets the linker put their
+ * relative position in the executable instead of leaving
+ * them null.
  */
-.globl _bss_start
-_bss_start:
-	.word __bss_start
+.globl _bss_start_ofs
+_bss_start_ofs:
+	.word __bss_start - _start
 
-.globl _bss_end
-_bss_end:
-	.word _end
+.globl _bss_end_ofs
+_bss_end_ofs:
+	.word _end - _start
 
 #ifdef CONFIG_USE_IRQ
 /* IRQ stack memory (calculated at run-time) */
@@ -104,30 +107,6 @@ FIQ_STACK_START:
 IRQ_STACK_START_IN:
 	.word	0x0badc0de
 
-.globl _datarel_start
-_datarel_start:
-	.word __datarel_start
-
-.globl _datarelrolocal_start
-_datarelrolocal_start:
-	.word __datarelrolocal_start
-
-.globl _datarellocal_start
-_datarellocal_start:
-	.word __datarellocal_start
-
-.globl _datarelro_start
-_datarelro_start:
-	.word __datarelro_start
-
-.globl _got_start
-_got_start:
-	.word __got_start
-
-.globl _got_end
-_got_end:
-	.word __got_end
-
 /*
  * the actual reset code
  */
@@ -177,9 +156,8 @@ stack_setup:
 
 	adr	r0, _start
 	ldr	r2, _TEXT_BASE
-	ldr	r3, _bss_start
-	sub	r2, r3, r2		/* r2 <- size of armboot	    */
-	add	r2, r0, r2		/* r2 <- source end address	    */
+	ldr	r3, _bss_start_ofs
+	add	r2, r0, r3		/* r2 <- source end address	    */
 	cmp	r0, r6
 	beq	clear_bss
 
@@ -190,35 +168,53 @@ copy_loop:
 	blo	copy_loop
 
 #ifndef CONFIG_PRELOADER
-	/* fix got entries */
-	ldr	r1, _TEXT_BASE		/* Text base */
-	mov	r0, r7			/* reloc addr */
-	ldr	r2, _got_start		/* addr in Flash */
-	ldr	r3, _got_end		/* addr in Flash */
-	sub	r3, r3, r1
-	add	r3, r3, r0
-	sub	r2, r2, r1
-	add	r2, r2, r0
-
+	/*
+	 * fix .rel.dyn relocations
+	 */
+	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
+	sub	r9, r7, r0		/* r9 <- relocation offset */
+	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
+	add	r10, r10, r0		/* r10 <- sym table in FLASH */
+	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
+	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
+	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
+	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
 fixloop:
-	ldr	r4, [r2]
-	sub	r4, r4, r1
-	add	r4, r4, r0
-	str	r4, [r2]
-	add	r2, r2, #4
+	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
+	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
+	ldr	r1, [r2, #4]
+	and	r8, r1, #0xff
+	cmp	r8, #23			/* relative fixup? */
+	beq	fixrel
+	cmp	r8, #2			/* absolute fixup? */
+	beq	fixabs
+	/* ignore unknown type of fixup */
+	b	fixnext
+fixabs:
+	/* absolute fix: set location to (offset) symbol value */
+	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
+	add	r1, r10, r1		/* r1 <- address of symbol in table */
+	ldr	r1, [r1, #4]		/* r1 <- symbol value */
+	add	r1, r9			/* r1 <- relocated sym addr */
+	b	fixnext
+fixrel:
+	/* relative fix: increase location by offset */
+	ldr	r1, [r0]
+	add	r1, r1, r9
+fixnext:
+	str	r1, [r0]
+	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
 	cmp	r2, r3
 	blo	fixloop
 #endif
 
 clear_bss:
 #ifndef CONFIG_PRELOADER
-	ldr	r0, _bss_start
-	ldr	r1, _bss_end
+	ldr	r0, _bss_start_ofs
+	ldr	r1, _bss_end_ofs
 	ldr	r3, _TEXT_BASE		/* Text base */
 	mov	r4, r7			/* reloc addr */
-	sub	r0, r0, r3
 	add	r0, r0, r4
-	sub	r1, r1, r3
 	add	r1, r1, r4
 	mov	r2, #0x00000000		/* clear			    */
 
@@ -232,18 +228,25 @@ clbss_l:str	r2, [r0]		/* clear loop...		    */
  * We are done. Do not return, instead branch to second part of board
  * initialization, now running from RAM.
  */
-	ldr	r0, _TEXT_BASE
-	ldr	r2, _board_init_r
-	sub	r2, r2, r0
-	add	r2, r2, r7	/* position from board_init_r in RAM */
+	ldr	r0, _board_init_r_ofs
+	adr	r1, _start
+	add	lr, r0, r1
+	add	lr, lr, r9
 	/* setup parameters for board_init_r */
 	mov	r0, r5		/* gd_t */
 	mov	r1, r7		/* dest_addr */
 	/* jump to it ... */
-	mov	lr, r2
 	mov	pc, lr
 
-_board_init_r: .word board_init_r
+_board_init_r_ofs:
+	.word board_init_r - _start
+
+_rel_dyn_start_ofs:
+	.word __rel_dyn_start - _start
+_rel_dyn_end_ofs:
+	.word __rel_dyn_end - _start
+_dynsym_start_ofs:
+	.word __dynsym_start - _start
 
 /*
  *************************************************************************

arch/arm/cpu/sa1100/u-boot.lds

@@ -44,28 +44,38 @@ SECTIONS
 	. = ALIGN(4);
 	.data : {
 		*(.data)
-	__datarel_start = .;
-		*(.data.rel)
-	__datarelrolocal_start = .;
-		*(.data.rel.ro.local)
-	__datarellocal_start = .;
-		*(.data.rel.local)
-	__datarelro_start = .;
-		*(.data.rel.ro)
 	}
 
-	__got_start = .;
 	. = ALIGN(4);
-	.got : { *(.got) }
 
-	__got_end = .;
 	. = .;
 	__u_boot_cmd_start = .;
 	.u_boot_cmd : { *(.u_boot_cmd) }
 	__u_boot_cmd_end = .;
 
 	. = ALIGN(4);
-	__bss_start = .;
-	.bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
-	_end = .;
+
+	.rel.dyn : {
+		__rel_dyn_start = .;
+		*(.rel*)
+		__rel_dyn_end = .;
+	}
+
+	.dynsym : {
+		__dynsym_start = .;
+		*(.dynsym)
+	}
+
+	.bss __rel_dyn_start (OVERLAY) : {
+		__bss_start = .;
+		*(.bss)
+		 . = ALIGN(4);
+		_end = .;
+	}
+
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
 }

board/Seagate/dockstar/Makefile

@@ -0,0 +1,54 @@
+#
+# Copyright (C) 2010  Eric C. Cooper <ecc@cmu.edu>
+#
+# Based on sheevaplug/Makefile originally written by
+# Prafulla Wadaskar <prafulla@marvell.com>
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= dockstar.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/Seagate/dockstar/dockstar.c

@@ -0,0 +1,181 @@
+/*
+ * Copyright (C) 2010  Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.c originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "dockstar.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the  below configuration configures mainly initial LED status
+	 */
+	kw_config_gpio(DOCKSTAR_OE_VAL_LOW,
+			DOCKSTAR_OE_VAL_HIGH,
+			DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	u32 kwmpp_config[] = {
+		MPP0_NF_IO2,
+		MPP1_NF_IO3,
+		MPP2_NF_IO4,
+		MPP3_NF_IO5,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,
+		MPP7_GPO,
+		MPP8_UART0_RTS,
+		MPP9_UART0_CTS,
+		MPP10_UART0_TXD,
+		MPP11_UART0_RXD,
+		MPP12_SD_CLK,
+		MPP13_SD_CMD,
+		MPP14_SD_D0,
+		MPP15_SD_D1,
+		MPP16_SD_D2,
+		MPP17_SD_D3,
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GPIO,
+		MPP21_GPIO,
+		MPP22_GPIO,
+		MPP23_GPIO,
+		MPP24_GPIO,
+		MPP25_GPIO,
+		MPP26_GPIO,
+		MPP27_GPIO,
+		MPP28_GPIO,
+		MPP29_TSMP9,
+		MPP30_GPIO,
+		MPP31_GPIO,
+		MPP32_GPIO,
+		MPP33_GPIO,
+		MPP34_GPIO,
+		MPP35_GPIO,
+		MPP36_GPIO,
+		MPP37_GPIO,
+		MPP38_GPIO,
+		MPP39_GPIO,
+		MPP40_GPIO,
+		MPP41_GPIO,
+		MPP42_GPIO,
+		MPP43_GPIO,
+		MPP44_GPIO,
+		MPP45_GPIO,
+		MPP46_GPIO,
+		MPP47_GPIO,
+		MPP48_GPIO,
+		MPP49_GPIO,
+		0
+	};
+	kirkwood_mpp_conf(kwmpp_config);
+	return 0;
+}
+
+int board_init(void)
+{
+	/*
+	 * arch number of board
+	 */
+	gd->bd->bi_arch_number = MACH_TYPE_DOCKSTAR;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+	u16 reg;
+	u16 devadr;
+	char *name = "egiga0";
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+		printf("Err..%s could not read PHY dev address\n",
+			__FUNCTION__);
+		return;
+	}
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, devadr);
+
+	printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#define GREEN_LED	(1 << 14)
+#define ORANGE_LED	(1 << 15)
+#define BOTH_LEDS	(GREEN_LED | ORANGE_LED)
+#define NEITHER_LED	0
+
+static void set_leds(u32 leds, u32 blinking)
+{
+	struct kwgpio_registers *r = (struct kwgpio_registers *)KW_GPIO1_BASE;
+	u32 oe = readl(&r->oe) | BOTH_LEDS;
+	writel(oe & ~leds, &r->oe);	/* active low */
+	u32 bl = readl(&r->blink_en) & ~BOTH_LEDS;
+	writel(bl | blinking, &r->blink_en);
+}
+
+void show_boot_progress(int val)
+{
+	switch (val) {
+	case 15:		/* booting Linux */
+		set_leds(BOTH_LEDS, NEITHER_LED);
+		break;
+	case 64:		/* Ethernet initialization */
+		set_leds(GREEN_LED, GREEN_LED);
+		break;
+	default:
+		if (val < 0)	/* error */
+			set_leds(ORANGE_LED, ORANGE_LED);
+		break;
+	}
+}

board/Seagate/dockstar/dockstar.h

@@ -0,0 +1,44 @@
+/*
+ * Copyright (C) 2010  Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.h originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __DOCKSTAR_H
+#define __DOCKSTAR_H
+
+#define DOCKSTAR_OE_LOW		(~(0))
+#define DOCKSTAR_OE_HIGH		(~(0))
+#define DOCKSTAR_OE_VAL_LOW		(1 << 29)	/* USB_PWEN low */
+#define DOCKSTAR_OE_VAL_HIGH		(1 << 17)	/* LED pin high */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG		10
+#define MV88E1116_CPRSP_CR3_REG		21
+#define MV88E1116_MAC_CTRL_REG		21
+#define MV88E1116_PGADR_REG		22
+#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
+
+#endif /* __DOCKSTAR_H */

board/Seagate/dockstar/kwbimage.cfg

@@ -0,0 +1,165 @@
+#
+# Copyright (C) 2010  Eric C. Cooper <ecc@cmu.edu>
+#
+# Based on sheevaplug/kwbimage.cfg originally written by
+# Prafulla Wadaskar <prafulla@marvell.com>
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	nand
+NAND_ECC_MODE	default
+NAND_PAGE_SIZE	0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30	# DDR Configuration register
+# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
+# bit 4:    0=addr/cmd in smame cycle
+# bit 5:    0=clk is driven during self refresh, we don't care for APX
+# bit 6:    0=use recommended falling edge of clk for addr/cmd
+# bit14:    0=input buffer always powered up
+# bit18:    1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
+# bit3-0:   TRAS lsbs
+# bit7-4:   TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x0000000d	#  DDR Address Control
+# bit1-0:   00, Cs0width=x8
+# bit3-2:   11, Cs0size=1Gb
+# bit5-4:   00, Cs1width=nonexistent
+# bit7-6:   00, Cs1size =nonexistent
+# bit9-8:   00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16:    0,  Cs0AddrSel
+# bit17:    0,  Cs1AddrSel
+# bit18:    0,  Cs2AddrSel
+# bit19:    0,  Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit0:    0,  OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0 required
+
+DATA 0xFFD0141C 0x00000C52	#  DDR Mode
+# bit2-0:   2, BurstLen=2 required
+# bit3:     0, BurstType=0 required
+# bit6-4:   4, CL=5
+# bit7:     0, TestMode=0 normal
+# bit8:     0, DLL reset=0 normal
+# bit11-9:  6, auto-precharge write recovery ????????????
+# bit12:    0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040	#  DDR Extended Mode
+# bit0:    0,  DDR DLL enabled
+# bit1:    0,  DDR drive strenght normal
+# bit2:    0,  DDR ODT control lsd (disabled)
+# bit5-3:  000, required
+# bit6:    1,  DDR ODT control msb, (disabled)
+# bit9-7:  000, required
+# bit10:   0,  differential DQS enabled
+# bit11:   0, required
+# bit12:   0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
+# bit2-0:  111, required
+# bit3  :  1  , MBUS Burst Chop disabled
+# bit6-4:  111, required
+# bit7  :  0
+# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9  :  0  , no half clock cycle addition to dataout
+# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0    required
+
+DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1	# CS[0]n Size
+# bit0:    1,  Window enabled
+# bit1:    0,  Write Protect disabled
+# bit3-2:  00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x07, Size (i.e. 128MB)
+
+DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
+
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00030000	#  DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
+# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
+# bit3-2:  01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E803	# CPU ODT Control
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0

board/davinci/da8xxevm/da850evm.c

@@ -118,6 +118,39 @@ static const struct lpsc_resource lpsc[] = {
 	{ DAVINCI_LPSC_GPIO },
 };
 
+#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
+#define CONFIG_DA850_EVM_MAX_CPU_CLK	300000000
+#endif
+
+/*
+ * get_board_rev() - setup to pass kernel board revision information
+ * Returns:
+ * bit[0-3]	Maximum cpu clock rate supported by onboard SoC
+ *		0000b - 300 MHz
+ *		0001b - 372 MHz
+ *		0010b - 408 MHz
+ *		0011b - 456 MHz
+ */
+u32 get_board_rev(void)
+{
+	char *s;
+	u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK;
+	u32 rev = 0;
+
+	s = getenv("maxcpuclk");
+	if (s)
+		maxcpuclk = simple_strtoul(s, NULL, 10);
+
+	if (maxcpuclk >= 456000000)
+		rev = 3;
+	else if (maxcpuclk >= 408000000)
+		rev = 2;
+	else if (maxcpuclk >= 372000000)
+		rev = 1;
+
+	return rev;
+}
+
 int board_init(void)
 {
 #ifndef CONFIG_USE_IRQ

board/pandora/config.mk

@@ -1,33 +0,0 @@
-#
-# (C) Copyright 2006
-# Texas Instruments, <www.ti.com>
-#
-# Pandora uses OMAP3 (ARM-CortexA8) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-# Physical Address:
-# 8000'0000 (bank0)
-# A000/0000 (bank1)
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-
-# For use with external or internal boots.
-CONFIG_SYS_TEXT_BASE = 0x80e80000

boards.cfg

@@ -53,6 +53,7 @@ pm9261		arm	arm926ejs	-		ronetix		at91
 pm9263		arm	arm926ejs	-		ronetix		at91
 suen3		arm	arm926ejs	km_arm		keymile		kirkwood
 rd6281a		arm	arm926ejs	-		Marvell		kirkwood
+dockstar	arm	arm926ejs	-		Seagate		kirkwood
 jadecpu		arm	arm926ejs	jadecpu		syteco		mb86r0x
 mx51evk		arm	armv7		mx51evk		freescale	mx5
 vision2		arm	armv7		vision2		ttcontrol	mx5

doc/README.davinci

@@ -21,6 +21,8 @@ Currently the following boards are supported:
 
 * TI DA830 EVM
 
+* TI DA850 EVM
+
 * DM355 based Leopard board
 
 * DM644x based schmoogie board
@@ -57,6 +59,11 @@ make
 make da830evm_config
 make
 
+* TI DA850 EVM:
+
+make da850evm_config
+make
+
 * DM355 based Leopard board:
 
 make davinci_dm355leopard_config
@@ -88,6 +95,20 @@ into the RAM.
 The programmers and UBL are always released as part of any standard TI
 software release associated with an SOC.
 
+Environment Variables
+=====================
+
+The DA850 EVM allows the user to specify the maximum cpu clock allowed by the
+silicon, in Hz, via an environment variable "maxcpuclk".
+
+The maximum clock rate allowed depends on the silicon populated on the EVM.
+Please make sure you understand the restrictions placed on this clock in the
+device specific datasheet before setting up this variable. This information is
+passed to the Linux kernel using the ATAG_REVISION atag.
+
+If "maxcpuclk" is not defined, the configuration CONFIG_DA850_EVM_MAX_CPU_CLK
+is used to obtain this information.
+
 Links
 =====
 
@@ -114,3 +135,7 @@ http://www.spectrumdigital.com/product_info.php?cPath=103&products_id=222
 6) TI DA830 EVM
 http://focus.ti.com/apps/docs/gencontent.tsp?appId=1&contentId=52385
 http://www.spectrumdigital.com/product_info.php?cPath=37&products_id=214
+
+7) TI DA850 EVM
+http://focus.ti.com/docs/prod/folders/print/omap-l138.html
+http://www.logicpd.com/products/development-kits/zoom-omap-l138-evm-development-kit

drivers/mmc/omap_hsmmc.c

@@ -31,6 +31,9 @@
 #include <asm/io.h>
 #include <asm/arch/mmc_host_def.h>
 
+/* If we fail after 1 second wait, something is really bad */
+#define MAX_RETRY_MS	1000
+
 static int mmc_read_data(hsmmc_t *mmc_base, char *buf, unsigned int size);
 static int mmc_write_data(hsmmc_t *mmc_base, const char *buf, unsigned int siz);
 static struct mmc hsmmc_dev[2];
@@ -70,18 +73,29 @@ unsigned char mmc_board_init(hsmmc_t *mmc_base)
 
 void mmc_init_stream(hsmmc_t *mmc_base)
 {
+	ulong start;
 
 	writel(readl(&mmc_base->con) | INIT_INITSTREAM, &mmc_base->con);
 
 	writel(MMC_CMD0, &mmc_base->cmd);
-	while (!(readl(&mmc_base->stat) & CC_MASK))
-		;
+	start = get_timer(0);
+	while (!(readl(&mmc_base->stat) & CC_MASK)) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for cc!\n", __func__);
+			return;
+		}
+	}
 	writel(CC_MASK, &mmc_base->stat)
 		;
 	writel(MMC_CMD0, &mmc_base->cmd)
 		;
-	while (!(readl(&mmc_base->stat) & CC_MASK))
-		;
+	start = get_timer(0);
+	while (!(readl(&mmc_base->stat) & CC_MASK)) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for cc2!\n", __func__);
+			return;
+		}
+	}
 	writel(readl(&mmc_base->con) & ~INIT_INITSTREAM, &mmc_base->con);
 }
 
@@ -91,16 +105,28 @@ static int mmc_init_setup(struct mmc *mmc)
 	hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv;
 	unsigned int reg_val;
 	unsigned int dsor;
+	ulong start;
 
 	mmc_board_init(mmc_base);
 
 	writel(readl(&mmc_base->sysconfig) | MMC_SOFTRESET,
 		&mmc_base->sysconfig);
-	while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0)
-		;
+	start = get_timer(0);
+	while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for cc2!\n", __func__);
+			return TIMEOUT;
+		}
+	}
 	writel(readl(&mmc_base->sysctl) | SOFTRESETALL, &mmc_base->sysctl);
-	while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0)
-		;
+	start = get_timer(0);
+	while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for softresetall!\n",
+				__func__);
+			return TIMEOUT;
+		}
+	}
 	writel(DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0, &mmc_base->hctl);
 	writel(readl(&mmc_base->capa) | VS30_3V0SUP | VS18_1V8SUP,
 		&mmc_base->capa);
@@ -116,8 +142,13 @@ static int mmc_init_setup(struct mmc *mmc)
 		(ICE_STOP | DTO_15THDTO | CEN_DISABLE));
 	mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK,
 		(dsor << CLKD_OFFSET) | ICE_OSCILLATE);
-	while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY)
-		;
+	start = get_timer(0);
+	while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for ics!\n", __func__);
+			return TIMEOUT;
+		}
+	}
 	writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl);
 
 	writel(readl(&mmc_base->hctl) | SDBP_PWRON, &mmc_base->hctl);
@@ -137,14 +168,23 @@ static int mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
 {
 	hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv;
 	unsigned int flags, mmc_stat;
-	unsigned int retry = 0x100000;
+	ulong start;
 
-
-	while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS)
-		;
+	start = get_timer(0);
+	while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for cmddis!\n", __func__);
+			return TIMEOUT;
+		}
+	}
 	writel(0xFFFFFFFF, &mmc_base->stat);
-	while (readl(&mmc_base->stat))
-		;
+	start = get_timer(0);
+	while (readl(&mmc_base->stat)) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for stat!\n", __func__);
+			return TIMEOUT;
+		}
+	}
 	/*
 	 * CMDREG
 	 * CMDIDX[13:8]	: Command index
@@ -200,15 +240,14 @@ static int mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
 	writel(cmd->cmdarg, &mmc_base->arg);
 	writel((cmd->cmdidx << 24) | flags, &mmc_base->cmd);
 
+	start = get_timer(0);
 	do {
 		mmc_stat = readl(&mmc_base->stat);
-		retry--;
-	} while ((mmc_stat == 0) && (retry > 0));
-
-	if (retry == 0) {
-		printf("%s : timeout: No status update\n", __func__);
-		return TIMEOUT;
-	}
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s : timeout: No status update\n", __func__);
+			return TIMEOUT;
+		}
+	} while (!mmc_stat);
 
 	if ((mmc_stat & IE_CTO) != 0)
 		return TIMEOUT;
@@ -253,8 +292,14 @@ static int mmc_read_data(hsmmc_t *mmc_base, char *buf, unsigned int size)
 	count /= 4;
 
 	while (size) {
+		ulong start = get_timer(0);
 		do {
 			mmc_stat = readl(&mmc_base->stat);
+			if (get_timer(0) - start > MAX_RETRY_MS) {
+				printf("%s: timedout waiting for status!\n",
+						__func__);
+				return TIMEOUT;
+			}
 		} while (mmc_stat == 0);
 
 		if ((mmc_stat & ERRI_MASK) != 0)
@@ -298,8 +343,14 @@ static int mmc_write_data(hsmmc_t *mmc_base, const char *buf, unsigned int size)
 	count /= 4;
 
 	while (size) {
+		ulong start = get_timer(0);
 		do {
 			mmc_stat = readl(&mmc_base->stat);
+			if (get_timer(0) - start > MAX_RETRY_MS) {
+				printf("%s: timedout waiting for status!\n",
+						__func__);
+				return TIMEOUT;
+			}
 		} while (mmc_stat == 0);
 
 		if ((mmc_stat & ERRI_MASK) != 0)
@@ -334,6 +385,7 @@ static void mmc_set_ios(struct mmc *mmc)
 {
 	hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv;
 	unsigned int dsor = 0;
+	ulong start;
 
 	/* configue bus width */
 	switch (mmc->bus_width) {
@@ -372,8 +424,13 @@ static void mmc_set_ios(struct mmc *mmc)
 	mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK,
 				(dsor << CLKD_OFFSET) | ICE_OSCILLATE);
 
-	while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY)
-		;
+	start = get_timer(0);
+	while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) {
+		if (get_timer(0) - start > MAX_RETRY_MS) {
+			printf("%s: timedout waiting for ics!\n", __func__);
+			return;
+		}
+	}
 	writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl);
 }
 

include/configs/da830evm.h

@@ -47,8 +47,7 @@
  * Memory Info
  */
 #define CONFIG_SYS_MALLOC_LEN	(0x10000 + 1*1024*1024) /* malloc() len */
-#define PHYS_SDRAM_1		DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
-#define PHYS_SDRAM_1_SIZE	(64 << 20) /* SDRAM size 64MB */
+#define PHYS_SDRAM_1			0xc0000000 /* SDRAM Start */
 #define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1 /* memtest start addr */
 #define CONFIG_SYS_MEMTEST_END 	(PHYS_SDRAM_1 + 16*1024*1024) /* 16MB test */
 #define CONFIG_NR_DRAM_BANKS	1 /* we have 1 bank of DRAM */
@@ -115,7 +114,6 @@
 #define CONFIG_SYS_ALE_MASK		0x8
 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
 #define NAND_MAX_CHIPS			1
-#define DEF_BOOTM			""
 #endif
 
 #ifdef CONFIG_USE_NOR
@@ -280,4 +278,11 @@
 	"mtdparts=davinci_nand.1:" PART_BOOT PART_PARAMS PART_KERNEL PART_REST
 #endif
 
+#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR		\
+	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */

include/configs/da850evm.h

@@ -99,7 +99,6 @@
 #undef CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
 #define NAND_MAX_CHIPS			1
-#define DEF_BOOTM			""
 #endif
 
 /*
@@ -140,6 +139,7 @@
  */
 #define LINUX_BOOT_PARAM_ADDR	(PHYS_SDRAM_1 + 0x100)
 #define CONFIG_CMDLINE_TAG
+#define CONFIG_REVISION_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_BOOTARGS		\
 	"mem=32M console=ttyS2,115200n8 root=/dev/mtdblock2 rw noinitrd ip=dhcp"

include/configs/davinci_dvevm.h

@@ -138,7 +138,6 @@
 #define CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
 #define CONFIG_ENV_OFFSET		0x0	/* Block 0--not used by bootcode */
-#define DEF_BOOTM		""
 #elif defined(CONFIG_SYS_USE_NOR)
 #ifdef CONFIG_NOR_UART_BOOT
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */

include/configs/davinci_sonata.h

@@ -126,7 +126,6 @@
 #define CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
 #define CONFIG_ENV_OFFSET		0x0	/* Block 0--not used by bootcode */
-#define DEF_BOOTM		""
 #elif defined(CONFIG_SYS_USE_NOR)
 #ifdef CONFIG_NOR_UART_BOOT
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* U-Boot is loaded by a bootloader */

include/configs/dockstar.h

@@ -0,0 +1,125 @@
+/*
+ * Copyright (C) 2010  Eric C. Cooper <ecc@cmu.edu>
+ *
+ * Based on sheevaplug.h originally written by
+ * Prafulla Wadaskar <prafulla@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_DOCKSTAR_H
+#define _CONFIG_DOCKSTAR_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING	"\nSeagate FreeAgent DockStar"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
+#define CONFIG_KIRKWOOD		1	/* SOC Family Name */
+#define CONFIG_KW88F6281	1	/* SOC Name */
+#define CONFIG_MACH_DOCKSTAR	/* Machine type */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_SYS_PROMPT	/* previously defined in mv-common.h */
+#define CONFIG_SYS_PROMPT	"DockStar> "	/* Command Prompt */
+
+/*
+ *  Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_SECT_SIZE		0x20000	/* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE		1	/* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE			0x20000	/* 128k */
+#define CONFIG_ENV_ADDR			0x60000
+#define CONFIG_ENV_OFFSET		0x60000	/* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+	"setenv bootargs ${console} ${mtdparts} ${bootargs_root}; "	\
+	"ubi part root; " \
+	"ubifsmount root; " \
+	"ubifsload 0x800000 ${kernel}; " \
+	"ubifsload 0x1100000 ${initrd}; " \
+	"bootm 0x800000 0x1100000"
+
+#define CONFIG_MTDPARTS		"mtdparts=orion_nand:1m(uboot),-(root)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console=console=ttyS0,115200\0" \
+	"mtdids=nand0=orion_nand\0" \
+	"mtdparts="CONFIG_MTDPARTS \
+	"kernel=/boot/uImage\0" \
+	"initrd=/boot/uInitrd\0" \
+	"bootargs_root=ubi.mtd=1 root=ubi0:root rootfstype=ubifs ro\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR	0
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _CONFIG_DOCKSTAR_H */

include/configs/omap3_beagle.h

@@ -304,9 +304,6 @@
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
 
-#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
-						/* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
@@ -323,21 +320,6 @@
 #define CONFIG_ENV_OFFSET		boot_flash_off
 #define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
 
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
-					CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-
 #ifndef __ASSEMBLY__
 extern unsigned int boot_flash_base;
 extern volatile unsigned int boot_flash_env_addr;

include/configs/omap3_evm.h

@@ -296,9 +296,6 @@
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
 
-#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors */
-						/* on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
@@ -321,21 +318,6 @@
 #define CONFIG_ENV_OFFSET		boot_flash_off
 #define CONFIG_ENV_ADDR			boot_flash_env_addr
 
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
-					CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-
 #ifndef __ASSEMBLY__
 extern unsigned int boot_flash_base;
 extern volatile unsigned int boot_flash_env_addr;

include/configs/omap3_overo.h

@@ -269,9 +269,6 @@
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
 
-#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
-						/* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
@@ -288,21 +285,6 @@
 #define CONFIG_ENV_OFFSET		boot_flash_off
 #define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
 
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
-					CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-
 #ifndef __ASSEMBLY__
 extern unsigned int boot_flash_base;
 extern volatile unsigned int boot_flash_env_addr;

include/configs/omap3_pandora.h

@@ -1,6 +1,6 @@
 /*
- * (C) Copyright 2008
- * Grazvydas Ignotas <notasas@gmail.com>
+ * (C) Copyright 2008-2010
+ * Gražvydas Ignotas <notasas@gmail.com>
  *
  * Configuration settings for the OMAP3 Pandora.
  *
@@ -59,14 +59,24 @@
  * Size of malloc() pool
  */
 #define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
-						/* Sector */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
-						/* initial data */
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024 + CONFIG_ENV_SIZE)
 
 /*
  * Hardware drivers
  */
 
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+#define CONFIG_SYS_DEVICE_NULLDEV	1
+
+/* USB */
+#define CONFIG_MUSB_UDC			1
+#define CONFIG_USB_OMAP3		1
+#define CONFIG_TWL4030_USB		1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE		1
+#define CONFIG_USB_TTY			1
+
 /*
  * NS16550 Configuration
  */
@@ -101,11 +111,11 @@
 
 #define CONFIG_CMD_EXT2		/* EXT2 Support			*/
 #define CONFIG_CMD_FAT		/* FAT support			*/
-#define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
 
 #define CONFIG_CMD_I2C		/* I2C serial bus support	*/
 #define CONFIG_CMD_MMC		/* MMC support			*/
 #define CONFIG_CMD_NAND		/* NAND support			*/
+#define CONFIG_CMD_CACHE	/* Cache control		*/
 
 #undef CONFIG_CMD_FLASH		/* flinfo, erase, protect	*/
 #undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
@@ -141,52 +151,41 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND */
 						/* devices */
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV		"nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET	0x680000
-#define CONFIG_JFFS2_PART_SIZE		0xf980000	/* size of jffs2 */
-							/* partition */
+
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+
+#define MTDIDS_DEFAULT			"nand0=nand"
+#define MTDPARTS_DEFAULT		"mtdparts=nand:512k(xloader),"\
+					"1920k(uboot),128k(uboot-env),"\
+					"10m(boot),-(rootfs)"
+#else
+#define MTDPARTS_DEFAULT
+#endif
 
 /* Environment information */
 #define CONFIG_BOOTDELAY		1
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
+	"usbtty=cdc_acm\0" \
 	"loadaddr=0x82000000\0" \
-	"console=ttyS0,115200n8\0" \
-	"videospec=omapfb:vram:2M,vram:4M\0" \
-	"mmcargs=setenv bootargs console=${console} " \
-		"video=${videospec} " \
-		"root=/dev/mmcblk0p2 rw " \
-		"rootfstype=ext3 rootwait\0" \
-	"nandargs=setenv bootargs console=${console} " \
-		"video=${videospec} " \
-		"root=/dev/mtdblock4 rw " \
-		"rootfstype=jffs2\0" \
-	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
-	"bootscript=echo Running bootscript from mmc ...; " \
-		"source ${loadaddr}\0" \
-	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
-	"mmcboot=echo Booting from mmc ...; " \
-		"run mmcargs; " \
-		"bootm ${loadaddr}\0" \
-	"nandboot=echo Booting from nand ...; " \
-		"run nandargs; " \
-		"nand read ${loadaddr} 280000 400000; " \
-		"bootm ${loadaddr}\0" \
+	"bootargs=ubi.mtd=4 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs " \
+	"rw rootflags=bulk_read console=ttyS0,115200n8 " \
+	"vram=6272K omapfb.vram=0:3000K\0" \
+	"mtdparts=" MTDPARTS_DEFAULT "\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmc init; then " \
-		"if run loadbootscript; then " \
-			"run bootscript; " \
-		"else " \
-			"if run loaduimage; then " \
-				"run mmcboot; " \
-			"else run nandboot; " \
-			"fi; " \
-		"fi; " \
-	"else run nandboot; fi"
+	"if mmc init && fatload mmc1 0 ${loadaddr} autoboot.scr || " \
+			"ext2load mmc1 0 ${loadaddr} autoboot.scr; then " \
+		"source ${loadaddr}; " \
+	"fi; " \
+	"ubi part boot && ubifsmount boot && ubifsload ${loadaddr} uImage && bootm ${loadaddr}"
 
 #define CONFIG_AUTO_COMPLETE	1
 /*
@@ -243,6 +242,14 @@
 /* SDRAM Bank Allocation method */
 #define SDRC_R_B_C		1
 
+#define CONFIG_SYS_TEXT_BASE		0x80008000
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE	0x800
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+
 /*-----------------------------------------------------------------------
  * FLASH and environment organization
  */
@@ -253,40 +260,20 @@
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
 
-#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
-						/* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
 
 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
 
 #define CONFIG_ENV_IS_IN_NAND		1
-#define ONENAND_ENV_OFFSET		0x240000 /* environment starts here */
-#define SMNAND_ENV_OFFSET		0x240000 /* environment starts here */
+#define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */
 
 #define CONFIG_SYS_ENV_SECT_SIZE	boot_flash_sec
 #define CONFIG_ENV_OFFSET		boot_flash_off
 #define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
 
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
-					CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-
 #ifndef __ASSEMBLY__
 extern unsigned int boot_flash_base;
 extern volatile unsigned int boot_flash_env_addr;

include/configs/omap3_sdp3430.h

@@ -159,10 +159,6 @@
 #define PHYS_FLASH_SIZE			(128 << 20)
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max sectors on one chip */
 
-/* timeout values are in milliseconds */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
-
 /* OMITTED:  single 2 Gbit KFM2G16 OneNAND flash */
 
 #define CONFIG_ENV_IS_IN_FLASH		1
@@ -338,9 +334,6 @@
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)
 
-#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-
 /*
  * NAND FLASH usage ... default nCS1:
  *  - four 128KB sectors for X-Loader

include/configs/omap3_zoom1.h

@@ -277,9 +277,6 @@
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
 
-#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
-						/* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
@@ -296,21 +293,6 @@
 #define CONFIG_ENV_OFFSET		boot_flash_off
 #define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
 
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
-					CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-
 #ifndef __ASSEMBLY__
 extern unsigned int boot_flash_base;
 extern volatile unsigned int boot_flash_env_addr;

include/configs/omap3_zoom2.h

@@ -246,9 +246,6 @@
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
 
-#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors on */
-						/* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
 
 #define CONFIG_SYS_FLASH_BASE		boot_flash_base
@@ -263,13 +260,6 @@
 #define CONFIG_ENV_OFFSET		boot_flash_off
 #define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
 
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
-
 #ifndef __ASSEMBLY__
 extern unsigned int boot_flash_base;
 extern volatile unsigned int boot_flash_env_addr;

include/configs/omap4_panda.h

@@ -134,6 +134,7 @@
 
 /* Disabled commands */
 #undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
 #undef CONFIG_CMD_FPGA		/* FPGA configuration Support   */
 #undef CONFIG_CMD_IMLS		/* List all found images        */
 

include/configs/tnetv107x_evm.h

@@ -86,7 +86,6 @@
 #define CONFIG_JFFS2_NAND
 #define NAND_MAX_CHIPS			1
 #define CONFIG_ENV_OFFSET		0x180000
-#define DEF_BOOTM			""
 
 /*
  * davinci_nand is a bit of a misnomer since this particular EMIF block is