Merge branch 'pm-cpufreq'

* pm-cpufreq:
  cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
  sections: fix section conflicts in drivers/cpufreq
  cpufreq: conservative: update frequency when limits are relaxed
  cpufreq / ondemand: update frequency when limits are relaxed
  cpufreq: Add a generic cpufreq-cpu0 driver
  PM / OPP: Initialize OPP table from device tree
  ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
  cpufreq: Remove support for hardware P-state chips from powernow-k8
  acpi-cpufreq: Add compatibility for legacy AMD cpb sysfs knob
  acpi-cpufreq: Add support for disabling dynamic overclocking
  ACPI: Add fixups for AMD P-state figures
  powernow-k8: delay info messages until initialization has succeeded
  cpufreq: Add warning message to powernow-k8
  acpi-cpufreq: Add quirk to disable _PSD usage on all AMD CPUs
  acpi-cpufreq: Add support for modern AMD CPUs
  cpufreq / powernow-k8: Fixup missing _PSS objects message
  PM / cpufreq: Initialise the cpu field during conservative governor start

Documentation/ABI/testing/sysfs-devices-system-cpu

@@ -176,3 +176,14 @@ Description:	Disable L3 cache indices
 		All AMD processors with L3 caches provide this functionality.
 		For details, see BKDGs at
 		http://developer.amd.com/documentation/guides/Pages/default.aspx
+
+
+What:		/sys/devices/system/cpu/cpufreq/boost
+Date:		August 2012
+Contact:	Linux kernel mailing list <linux-kernel@vger.kernel.org>
+Description:	Processor frequency boosting control
+
+		This switch controls the boost setting for the whole system.
+		Boosting allows the CPU and the firmware to run at a frequency
+		beyound it's nominal limit.
+		More details can be found in Documentation/cpu-freq/boost.txt

Documentation/cpu-freq/boost.txt

@@ -0,0 +1,93 @@
+Processor boosting control
+
+	- information for users -
+
+Quick guide for the impatient:
+--------------------
+/sys/devices/system/cpu/cpufreq/boost
+controls the boost setting for the whole system. You can read and write
+that file with either "0" (boosting disabled) or "1" (boosting allowed).
+Reading or writing 1 does not mean that the system is boosting at this
+very moment, but only that the CPU _may_ raise the frequency at it's
+discretion.
+--------------------
+
+Introduction
+-------------
+Some CPUs support a functionality to raise the operating frequency of
+some cores in a multi-core package if certain conditions apply, mostly
+if the whole chip is not fully utilized and below it's intended thermal
+budget. This is done without operating system control by a combination
+of hardware and firmware.
+On Intel CPUs this is called "Turbo Boost", AMD calls it "Turbo-Core",
+in technical documentation "Core performance boost". In Linux we use
+the term "boost" for convenience.
+
+Rationale for disable switch
+----------------------------
+
+Though the idea is to just give better performance without any user
+intervention, sometimes the need arises to disable this functionality.
+Most systems offer a switch in the (BIOS) firmware to disable the
+functionality at all, but a more fine-grained and dynamic control would
+be desirable:
+1. While running benchmarks, reproducible results are important. Since
+   the boosting functionality depends on the load of the whole package,
+   single thread performance can vary. By explicitly disabling the boost
+   functionality at least for the benchmark's run-time the system will run
+   at a fixed frequency and results are reproducible again.
+2. To examine the impact of the boosting functionality it is helpful
+   to do tests with and without boosting.
+3. Boosting means overclocking the processor, though under controlled
+   conditions. By raising the frequency and the voltage the processor
+   will consume more power than without the boosting, which may be
+   undesirable for instance for mobile users. Disabling boosting may
+   save power here, though this depends on the workload.
+
+
+User controlled switch
+----------------------
+
+To allow the user to toggle the boosting functionality, the acpi-cpufreq
+driver exports a sysfs knob to disable it. There is a file:
+/sys/devices/system/cpu/cpufreq/boost
+which can either read "0" (boosting disabled) or "1" (boosting enabled).
+Reading the file is always supported, even if the processor does not
+support boosting. In this case the file will be read-only and always
+reads as "0". Explicitly changing the permissions and writing to that
+file anyway will return EINVAL.
+
+On supported CPUs one can write either a "0" or a "1" into this file.
+This will either disable the boost functionality on all cores in the
+whole system (0) or will allow the hardware to boost at will (1).
+
+Writing a "1" does not explicitly boost the system, but just allows the
+CPU (and the firmware) to boost at their discretion. Some implementations
+take external factors like the chip's temperature into account, so
+boosting once does not necessarily mean that it will occur every time
+even using the exact same software setup.
+
+
+AMD legacy cpb switch
+---------------------
+The AMD powernow-k8 driver used to support a very similar switch to
+disable or enable the "Core Performance Boost" feature of some AMD CPUs.
+This switch was instantiated in each CPU's cpufreq directory
+(/sys/devices/system/cpu[0-9]*/cpufreq) and was called "cpb".
+Though the per CPU existence hints at a more fine grained control, the
+actual implementation only supported a system-global switch semantics,
+which was simply reflected into each CPU's file. Writing a 0 or 1 into it
+would pull the other CPUs to the same state.
+For compatibility reasons this file and its behavior is still supported
+on AMD CPUs, though it is now protected by a config switch
+(X86_ACPI_CPUFREQ_CPB). On Intel CPUs this file will never be created,
+even with the config option set.
+This functionality is considered legacy and will be removed in some future
+kernel version.
+
+More fine grained boosting control
+----------------------------------
+
+Technically it is possible to switch the boosting functionality at least
+on a per package basis, for some CPUs even per core. Currently the driver
+does not support it, but this may be implemented in the future.

Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt

@@ -0,0 +1,55 @@
+Generic CPU0 cpufreq driver
+
+It is a generic cpufreq driver for CPU0 frequency management.  It
+supports both uniprocessor (UP) and symmetric multiprocessor (SMP)
+systems which share clock and voltage across all CPUs.
+
+Both required and optional properties listed below must be defined
+under node /cpus/cpu@0.
+
+Required properties:
+- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt
+  for details
+
+Optional properties:
+- clock-latency: Specify the possible maximum transition latency for clock,
+  in unit of nanoseconds.
+- voltage-tolerance: Specify the CPU voltage tolerance in percentage.
+
+Examples:
+
+cpus {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	cpu@0 {
+		compatible = "arm,cortex-a9";
+		reg = <0>;
+		next-level-cache = <&L2>;
+		operating-points = <
+			/* kHz    uV */
+			792000  1100000
+			396000  950000
+			198000  850000
+		>;
+		transition-latency = <61036>; /* two CLK32 periods */
+	};
+
+	cpu@1 {
+		compatible = "arm,cortex-a9";
+		reg = <1>;
+		next-level-cache = <&L2>;
+	};
+
+	cpu@2 {
+		compatible = "arm,cortex-a9";
+		reg = <2>;
+		next-level-cache = <&L2>;
+	};
+
+	cpu@3 {
+		compatible = "arm,cortex-a9";
+		reg = <3>;
+		next-level-cache = <&L2>;
+	};
+};

Documentation/devicetree/bindings/power/opp.txt

@@ -0,0 +1,25 @@
+* Generic OPP Interface
+
+SoCs have a standard set of tuples consisting of frequency and
+voltage pairs that the device will support per voltage domain. These
+are called Operating Performance Points or OPPs.
+
+Properties:
+- operating-points: An array of 2-tuples items, and each item consists
+  of frequency and voltage like <freq-kHz vol-uV>.
+	freq: clock frequency in kHz
+	vol: voltage in microvolt
+
+Examples:
+
+cpu@0 {
+	compatible = "arm,cortex-a9";
+	reg = <0>;
+	next-level-cache = <&L2>;
+	operating-points = <
+		/* kHz    uV */
+		792000  1100000
+		396000  950000
+		198000  850000
+	>;
+};

arch/arm/kernel/smp.c

@@ -25,6 +25,7 @@
 #include <linux/percpu.h>
 #include <linux/clockchips.h>
 #include <linux/completion.h>
+#include <linux/cpufreq.h>
 
 #include <linux/atomic.h>
 #include <asm/cacheflush.h>
@@ -584,3 +585,56 @@ int setup_profiling_timer(unsigned int multiplier)
 {
 	return -EINVAL;
 }
+
+#ifdef CONFIG_CPU_FREQ
+
+static DEFINE_PER_CPU(unsigned long, l_p_j_ref);
+static DEFINE_PER_CPU(unsigned long, l_p_j_ref_freq);
+static unsigned long global_l_p_j_ref;
+static unsigned long global_l_p_j_ref_freq;
+
+static int cpufreq_callback(struct notifier_block *nb,
+					unsigned long val, void *data)
+{
+	struct cpufreq_freqs *freq = data;
+	int cpu = freq->cpu;
+
+	if (freq->flags & CPUFREQ_CONST_LOOPS)
+		return NOTIFY_OK;
+
+	if (!per_cpu(l_p_j_ref, cpu)) {
+		per_cpu(l_p_j_ref, cpu) =
+			per_cpu(cpu_data, cpu).loops_per_jiffy;
+		per_cpu(l_p_j_ref_freq, cpu) = freq->old;
+		if (!global_l_p_j_ref) {
+			global_l_p_j_ref = loops_per_jiffy;
+			global_l_p_j_ref_freq = freq->old;
+		}
+	}
+
+	if ((val == CPUFREQ_PRECHANGE  && freq->old < freq->new) ||
+	    (val == CPUFREQ_POSTCHANGE && freq->old > freq->new) ||
+	    (val == CPUFREQ_RESUMECHANGE || val == CPUFREQ_SUSPENDCHANGE)) {
+		loops_per_jiffy = cpufreq_scale(global_l_p_j_ref,
+						global_l_p_j_ref_freq,
+						freq->new);
+		per_cpu(cpu_data, cpu).loops_per_jiffy =
+			cpufreq_scale(per_cpu(l_p_j_ref, cpu),
+					per_cpu(l_p_j_ref_freq, cpu),
+					freq->new);
+	}
+	return NOTIFY_OK;
+}
+
+static struct notifier_block cpufreq_notifier = {
+	.notifier_call  = cpufreq_callback,
+};
+
+static int __init register_cpufreq_notifier(void)
+{
+	return cpufreq_register_notifier(&cpufreq_notifier,
+						CPUFREQ_TRANSITION_NOTIFIER);
+}
+core_initcall(register_cpufreq_notifier);
+
+#endif

arch/x86/include/asm/msr-index.h

@@ -248,6 +248,9 @@
 
 #define MSR_IA32_PERF_STATUS		0x00000198
 #define MSR_IA32_PERF_CTL		0x00000199
+#define MSR_AMD_PSTATE_DEF_BASE		0xc0010064
+#define MSR_AMD_PERF_STATUS		0xc0010063
+#define MSR_AMD_PERF_CTL		0xc0010062
 
 #define MSR_IA32_MPERF			0x000000e7
 #define MSR_IA32_APERF			0x000000e8

drivers/acpi/processor_perflib.c

@@ -324,6 +324,34 @@ static int acpi_processor_get_performance_control(struct acpi_processor *pr)
 	return result;
 }
 
+#ifdef CONFIG_X86
+/*
+ * Some AMDs have 50MHz frequency multiples, but only provide 100MHz rounding
+ * in their ACPI data. Calculate the real values and fix up the _PSS data.
+ */
+static void amd_fixup_frequency(struct acpi_processor_px *px, int i)
+{
+	u32 hi, lo, fid, did;
+	int index = px->control & 0x00000007;
+
+	if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD)
+		return;
+
+	if ((boot_cpu_data.x86 == 0x10 && boot_cpu_data.x86_model < 10)
+	    || boot_cpu_data.x86 == 0x11) {
+		rdmsr(MSR_AMD_PSTATE_DEF_BASE + index, lo, hi);
+		fid = lo & 0x3f;
+		did = (lo >> 6) & 7;
+		if (boot_cpu_data.x86 == 0x10)
+			px->core_frequency = (100 * (fid + 0x10)) >> did;
+		else
+			px->core_frequency = (100 * (fid + 8)) >> did;
+	}
+}
+#else
+static void amd_fixup_frequency(struct acpi_processor_px *px, int i) {};
+#endif
+
 static int acpi_processor_get_performance_states(struct acpi_processor *pr)
 {
 	int result = 0;
@@ -379,6 +407,8 @@ static int acpi_processor_get_performance_states(struct acpi_processor *pr)
 			goto end;
 		}
 
+		amd_fixup_frequency(px, i);
+
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO,
 				  "State [%d]: core_frequency[%d] power[%d] transition_latency[%d] bus_master_latency[%d] control[0x%x] status[0x%x]\n",
 				  i,

drivers/base/power/opp.c

@@ -22,6 +22,7 @@
 #include <linux/rculist.h>
 #include <linux/rcupdate.h>
 #include <linux/opp.h>
+#include <linux/of.h>
 
 /*
  * Internal data structure organization with the OPP layer library is as
@@ -674,3 +675,49 @@ struct srcu_notifier_head *opp_get_notifier(struct device *dev)
 
 	return &dev_opp->head;
 }
+
+#ifdef CONFIG_OF
+/**
+ * of_init_opp_table() - Initialize opp table from device tree
+ * @dev:	device pointer used to lookup device OPPs.
+ *
+ * Register the initial OPP table with the OPP library for given device.
+ */
+int of_init_opp_table(struct device *dev)
+{
+	const struct property *prop;
+	const __be32 *val;
+	int nr;
+
+	prop = of_find_property(dev->of_node, "operating-points", NULL);
+	if (!prop)
+		return -ENODEV;
+	if (!prop->value)
+		return -ENODATA;
+
+	/*
+	 * Each OPP is a set of tuples consisting of frequency and
+	 * voltage like <freq-kHz vol-uV>.
+	 */
+	nr = prop->length / sizeof(u32);
+	if (nr % 2) {
+		dev_err(dev, "%s: Invalid OPP list\n", __func__);
+		return -EINVAL;
+	}
+
+	val = prop->value;
+	while (nr) {
+		unsigned long freq = be32_to_cpup(val++) * 1000;
+		unsigned long volt = be32_to_cpup(val++);
+
+		if (opp_add(dev, freq, volt)) {
+			dev_warn(dev, "%s: Failed to add OPP %ld\n",
+				 __func__, freq);
+			continue;
+		}
+		nr -= 2;
+	}
+
+	return 0;
+}
+#endif

drivers/cpufreq/Kconfig

@@ -179,6 +179,17 @@ config CPU_FREQ_GOV_CONSERVATIVE
 
 	  If in doubt, say N.
 
+config GENERIC_CPUFREQ_CPU0
+	bool "Generic CPU0 cpufreq driver"
+	depends on HAVE_CLK && REGULATOR && PM_OPP && OF
+	select CPU_FREQ_TABLE
+	help
+	  This adds a generic cpufreq driver for CPU0 frequency management.
+	  It supports both uniprocessor (UP) and symmetric multiprocessor (SMP)
+	  systems which share clock and voltage across all CPUs.
+
+	  If in doubt, say N.
+
 menu "x86 CPU frequency scaling drivers"
 depends on X86
 source "drivers/cpufreq/Kconfig.x86"

drivers/cpufreq/Kconfig.x86

@@ -23,7 +23,8 @@ config X86_ACPI_CPUFREQ
 	help
 	  This driver adds a CPUFreq driver which utilizes the ACPI
 	  Processor Performance States.
-	  This driver also supports Intel Enhanced Speedstep.
+	  This driver also supports Intel Enhanced Speedstep and newer
+	  AMD CPUs.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called acpi-cpufreq.
@@ -32,6 +33,18 @@ config X86_ACPI_CPUFREQ
 
 	  If in doubt, say N.
 
+config X86_ACPI_CPUFREQ_CPB
+	default y
+	bool "Legacy cpb sysfs knob support for AMD CPUs"
+	depends on X86_ACPI_CPUFREQ && CPU_SUP_AMD
+	help
+	  The powernow-k8 driver used to provide a sysfs knob called "cpb"
+	  to disable the Core Performance Boosting feature of AMD CPUs. This
+	  file has now been superseeded by the more generic "boost" entry.
+
+	  By enabling this option the acpi_cpufreq driver provides the old
+	  entry in addition to the new boost ones, for compatibility reasons.
+
 config ELAN_CPUFREQ
 	tristate "AMD Elan SC400 and SC410"
 	select CPU_FREQ_TABLE
@@ -95,7 +108,8 @@ config X86_POWERNOW_K8
 	select CPU_FREQ_TABLE
 	depends on ACPI && ACPI_PROCESSOR
 	help
-	  This adds the CPUFreq driver for K8/K10 Opteron/Athlon64 processors.
+	  This adds the CPUFreq driver for K8/early Opteron/Athlon64 processors.
+	  Support for K10 and newer processors is now in acpi-cpufreq.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called powernow-k8.

drivers/cpufreq/Makefile

@@ -13,13 +13,15 @@ obj-$(CONFIG_CPU_FREQ_GOV_CONSERVATIVE)	+= cpufreq_conservative.o
 # CPUfreq cross-arch helpers
 obj-$(CONFIG_CPU_FREQ_TABLE)		+= freq_table.o
 
+obj-$(CONFIG_GENERIC_CPUFREQ_CPU0)	+= cpufreq-cpu0.o
+
 ##################################################################################
 # x86 drivers.
 # Link order matters. K8 is preferred to ACPI because of firmware bugs in early
 # K8 systems. ACPI is preferred to all other hardware-specific drivers.
 # speedstep-* is preferred over p4-clockmod.
 
-obj-$(CONFIG_X86_POWERNOW_K8)		+= powernow-k8.o mperf.o
+obj-$(CONFIG_X86_POWERNOW_K8)		+= powernow-k8.o
 obj-$(CONFIG_X86_ACPI_CPUFREQ)		+= acpi-cpufreq.o mperf.o
 obj-$(CONFIG_X86_PCC_CPUFREQ)		+= pcc-cpufreq.o
 obj-$(CONFIG_X86_POWERNOW_K6)		+= powernow-k6.o

drivers/cpufreq/acpi-cpufreq.c

@@ -51,13 +51,19 @@ MODULE_AUTHOR("Paul Diefenbaugh, Dominik Brodowski");
 MODULE_DESCRIPTION("ACPI Processor P-States Driver");
 MODULE_LICENSE("GPL");
 
+#define PFX "acpi-cpufreq: "
+
 enum {
 	UNDEFINED_CAPABLE = 0,
 	SYSTEM_INTEL_MSR_CAPABLE,
+	SYSTEM_AMD_MSR_CAPABLE,
 	SYSTEM_IO_CAPABLE,
 };
 
 #define INTEL_MSR_RANGE		(0xffff)
+#define AMD_MSR_RANGE		(0x7)
+
+#define MSR_K7_HWCR_CPB_DIS	(1ULL << 25)
 
 struct acpi_cpufreq_data {
 	struct acpi_processor_performance *acpi_data;
@@ -74,6 +80,116 @@ static struct acpi_processor_performance __percpu *acpi_perf_data;
 static struct cpufreq_driver acpi_cpufreq_driver;
 
 static unsigned int acpi_pstate_strict;
+static bool boost_enabled, boost_supported;
+static struct msr __percpu *msrs;
+
+static bool boost_state(unsigned int cpu)
+{
+	u32 lo, hi;
+	u64 msr;
+
+	switch (boot_cpu_data.x86_vendor) {
+	case X86_VENDOR_INTEL:
+		rdmsr_on_cpu(cpu, MSR_IA32_MISC_ENABLE, &lo, &hi);
+		msr = lo | ((u64)hi << 32);
+		return !(msr & MSR_IA32_MISC_ENABLE_TURBO_DISABLE);
+	case X86_VENDOR_AMD:
+		rdmsr_on_cpu(cpu, MSR_K7_HWCR, &lo, &hi);
+		msr = lo | ((u64)hi << 32);
+		return !(msr & MSR_K7_HWCR_CPB_DIS);
+	}
+	return false;
+}
+
+static void boost_set_msrs(bool enable, const struct cpumask *cpumask)
+{
+	u32 cpu;
+	u32 msr_addr;
+	u64 msr_mask;
+
+	switch (boot_cpu_data.x86_vendor) {
+	case X86_VENDOR_INTEL:
+		msr_addr = MSR_IA32_MISC_ENABLE;
+		msr_mask = MSR_IA32_MISC_ENABLE_TURBO_DISABLE;
+		break;
+	case X86_VENDOR_AMD:
+		msr_addr = MSR_K7_HWCR;
+		msr_mask = MSR_K7_HWCR_CPB_DIS;
+		break;
+	default:
+		return;
+	}
+
+	rdmsr_on_cpus(cpumask, msr_addr, msrs);
+
+	for_each_cpu(cpu, cpumask) {
+		struct msr *reg = per_cpu_ptr(msrs, cpu);
+		if (enable)
+			reg->q &= ~msr_mask;
+		else
+			reg->q |= msr_mask;
+	}
+
+	wrmsr_on_cpus(cpumask, msr_addr, msrs);
+}
+
+static ssize_t _store_boost(const char *buf, size_t count)
+{
+	int ret;
+	unsigned long val = 0;
+
+	if (!boost_supported)
+		return -EINVAL;
+
+	ret = kstrtoul(buf, 10, &val);
+	if (ret || (val > 1))
+		return -EINVAL;
+
+	if ((val && boost_enabled) || (!val && !boost_enabled))
+		return count;
+
+	get_online_cpus();
+
+	boost_set_msrs(val, cpu_online_mask);
+
+	put_online_cpus();
+
+	boost_enabled = val;
+	pr_debug("Core Boosting %sabled.\n", val ? "en" : "dis");
+
+	return count;
+}
+
+static ssize_t store_global_boost(struct kobject *kobj, struct attribute *attr,
+				  const char *buf, size_t count)
+{
+	return _store_boost(buf, count);
+}
+
+static ssize_t show_global_boost(struct kobject *kobj,
+				 struct attribute *attr, char *buf)
+{
+	return sprintf(buf, "%u\n", boost_enabled);
+}
+
+static struct global_attr global_boost = __ATTR(boost, 0644,
+						show_global_boost,
+						store_global_boost);
+
+#ifdef CONFIG_X86_ACPI_CPUFREQ_CPB
+static ssize_t store_cpb(struct cpufreq_policy *policy, const char *buf,
+			 size_t count)
+{
+	return _store_boost(buf, count);
+}
+
+static ssize_t show_cpb(struct cpufreq_policy *policy, char *buf)
+{
+	return sprintf(buf, "%u\n", boost_enabled);
+}
+
+static struct freq_attr cpb = __ATTR(cpb, 0644, show_cpb, store_cpb);
+#endif
 
 static int check_est_cpu(unsigned int cpuid)
 {
@@ -82,6 +198,13 @@ static int check_est_cpu(unsigned int cpuid)
 	return cpu_has(cpu, X86_FEATURE_EST);
 }
 
+static int check_amd_hwpstate_cpu(unsigned int cpuid)
+{
+	struct cpuinfo_x86 *cpu = &cpu_data(cpuid);
+
+	return cpu_has(cpu, X86_FEATURE_HW_PSTATE);
+}
+
 static unsigned extract_io(u32 value, struct acpi_cpufreq_data *data)
 {
 	struct acpi_processor_performance *perf;
@@ -101,7 +224,11 @@ static unsigned extract_msr(u32 msr, struct acpi_cpufreq_data *data)
 	int i;
 	struct acpi_processor_performance *perf;
 
-	msr &= INTEL_MSR_RANGE;
+	if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD)
+		msr &= AMD_MSR_RANGE;
+	else
+		msr &= INTEL_MSR_RANGE;
+
 	perf = data->acpi_data;
 
 	for (i = 0; data->freq_table[i].frequency != CPUFREQ_TABLE_END; i++) {
@@ -115,6 +242,7 @@ static unsigned extract_freq(u32 val, struct acpi_cpufreq_data *data)
 {
 	switch (data->cpu_feature) {
 	case SYSTEM_INTEL_MSR_CAPABLE:
+	case SYSTEM_AMD_MSR_CAPABLE:
 		return extract_msr(val, data);
 	case SYSTEM_IO_CAPABLE:
 		return extract_io(val, data);
@@ -150,6 +278,7 @@ static void do_drv_read(void *_cmd)
 
 	switch (cmd->type) {
 	case SYSTEM_INTEL_MSR_CAPABLE:
+	case SYSTEM_AMD_MSR_CAPABLE:
 		rdmsr(cmd->addr.msr.reg, cmd->val, h);
 		break;
 	case SYSTEM_IO_CAPABLE:
@@ -174,6 +303,9 @@ static void do_drv_write(void *_cmd)
 		lo = (lo & ~INTEL_MSR_RANGE) | (cmd->val & INTEL_MSR_RANGE);
 		wrmsr(cmd->addr.msr.reg, lo, hi);
 		break;
+	case SYSTEM_AMD_MSR_CAPABLE:
+		wrmsr(cmd->addr.msr.reg, cmd->val, 0);
+		break;
 	case SYSTEM_IO_CAPABLE:
 		acpi_os_write_port((acpi_io_address)cmd->addr.io.port,
 				cmd->val,
@@ -217,6 +349,10 @@ static u32 get_cur_val(const struct cpumask *mask)
 		cmd.type = SYSTEM_INTEL_MSR_CAPABLE;
 		cmd.addr.msr.reg = MSR_IA32_PERF_STATUS;
 		break;
+	case SYSTEM_AMD_MSR_CAPABLE:
+		cmd.type = SYSTEM_AMD_MSR_CAPABLE;
+		cmd.addr.msr.reg = MSR_AMD_PERF_STATUS;
+		break;
 	case SYSTEM_IO_CAPABLE:
 		cmd.type = SYSTEM_IO_CAPABLE;
 		perf = per_cpu(acfreq_data, cpumask_first(mask))->acpi_data;
@@ -326,6 +462,11 @@ static int acpi_cpufreq_target(struct cpufreq_policy *policy,
 		cmd.addr.msr.reg = MSR_IA32_PERF_CTL;
 		cmd.val = (u32) perf->states[next_perf_state].control;
 		break;
+	case SYSTEM_AMD_MSR_CAPABLE:
+		cmd.type = SYSTEM_AMD_MSR_CAPABLE;
+		cmd.addr.msr.reg = MSR_AMD_PERF_CTL;
+		cmd.val = (u32) perf->states[next_perf_state].control;
+		break;
 	case SYSTEM_IO_CAPABLE:
 		cmd.type = SYSTEM_IO_CAPABLE;
 		cmd.addr.io.port = perf->control_register.address;
@@ -419,6 +560,44 @@ static void free_acpi_perf_data(void)
 	free_percpu(acpi_perf_data);
 }
 
+static int boost_notify(struct notifier_block *nb, unsigned long action,
+		      void *hcpu)
+{
+	unsigned cpu = (long)hcpu;
+	const struct cpumask *cpumask;
+
+	cpumask = get_cpu_mask(cpu);
+
+	/*
+	 * Clear the boost-disable bit on the CPU_DOWN path so that
+	 * this cpu cannot block the remaining ones from boosting. On
+	 * the CPU_UP path we simply keep the boost-disable flag in
+	 * sync with the current global state.
+	 */
+
+	switch (action) {
+	case CPU_UP_PREPARE:
+	case CPU_UP_PREPARE_FROZEN:
+		boost_set_msrs(boost_enabled, cpumask);
+		break;
+
+	case CPU_DOWN_PREPARE:
+	case CPU_DOWN_PREPARE_FROZEN:
+		boost_set_msrs(1, cpumask);
+		break;
+
+	default:
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+
+
+static struct notifier_block boost_nb = {
+	.notifier_call          = boost_notify,
+};
+
 /*
  * acpi_cpufreq_early_init - initialize ACPI P-States library
  *
@@ -559,6 +738,14 @@ static int acpi_cpufreq_cpu_init(struct cpufreq_policy *policy)
 		policy->shared_type = CPUFREQ_SHARED_TYPE_ALL;
 		cpumask_copy(policy->cpus, cpu_core_mask(cpu));
 	}
+
+	if (check_amd_hwpstate_cpu(cpu) && !acpi_pstate_strict) {
+		cpumask_clear(policy->cpus);
+		cpumask_set_cpu(cpu, policy->cpus);
+		cpumask_copy(policy->related_cpus, cpu_sibling_mask(cpu));
+		policy->shared_type = CPUFREQ_SHARED_TYPE_HW;
+		pr_info_once(PFX "overriding BIOS provided _PSD data\n");
+	}
 #endif
 
 	/* capability check */
@@ -580,12 +767,16 @@ static int acpi_cpufreq_cpu_init(struct cpufreq_policy *policy)
 		break;
 	case ACPI_ADR_SPACE_FIXED_HARDWARE:
 		pr_debug("HARDWARE addr space\n");
-		if (!check_est_cpu(cpu)) {
-			result = -ENODEV;
-			goto err_unreg;
+		if (check_est_cpu(cpu)) {
+			data->cpu_feature = SYSTEM_INTEL_MSR_CAPABLE;
+			break;
 		}
-		data->cpu_feature = SYSTEM_INTEL_MSR_CAPABLE;
-		break;
+		if (check_amd_hwpstate_cpu(cpu)) {
+			data->cpu_feature = SYSTEM_AMD_MSR_CAPABLE;
+			break;
+		}
+		result = -ENODEV;
+		goto err_unreg;
 	default:
 		pr_debug("Unknown addr space %d\n",
 			(u32) (perf->control_register.space_id));
@@ -718,6 +909,7 @@ static int acpi_cpufreq_resume(struct cpufreq_policy *policy)
 
 static struct freq_attr *acpi_cpufreq_attr[] = {
 	&cpufreq_freq_attr_scaling_available_freqs,
+	NULL,	/* this is a placeholder for cpb, do not remove */
 	NULL,
 };
 
@@ -733,6 +925,49 @@ static struct cpufreq_driver acpi_cpufreq_driver = {
 	.attr		= acpi_cpufreq_attr,
 };
 
+static void __init acpi_cpufreq_boost_init(void)
+{
+	if (boot_cpu_has(X86_FEATURE_CPB) || boot_cpu_has(X86_FEATURE_IDA)) {
+		msrs = msrs_alloc();
+
+		if (!msrs)
+			return;
+
+		boost_supported = true;
+		boost_enabled = boost_state(0);
+
+		get_online_cpus();
+
+		/* Force all MSRs to the same value */
+		boost_set_msrs(boost_enabled, cpu_online_mask);
+
+		register_cpu_notifier(&boost_nb);
+
+		put_online_cpus();
+	} else
+		global_boost.attr.mode = 0444;
+
+	/* We create the boost file in any case, though for systems without
+	 * hardware support it will be read-only and hardwired to return 0.
+	 */
+	if (sysfs_create_file(cpufreq_global_kobject, &(global_boost.attr)))
+		pr_warn(PFX "could not register global boost sysfs file\n");
+	else
+		pr_debug("registered global boost sysfs file\n");
+}
+
+static void __exit acpi_cpufreq_boost_exit(void)
+{
+	sysfs_remove_file(cpufreq_global_kobject, &(global_boost.attr));
+
+	if (msrs) {
+		unregister_cpu_notifier(&boost_nb);
+
+		msrs_free(msrs);
+		msrs = NULL;
+	}
+}
+
 static int __init acpi_cpufreq_init(void)
 {
 	int ret;
@@ -746,9 +981,32 @@ static int __init acpi_cpufreq_init(void)
 	if (ret)
 		return ret;
 
+#ifdef CONFIG_X86_ACPI_CPUFREQ_CPB
+	/* this is a sysfs file with a strange name and an even stranger
+	 * semantic - per CPU instantiation, but system global effect.
+	 * Lets enable it only on AMD CPUs for compatibility reasons and
+	 * only if configured. This is considered legacy code, which
+	 * will probably be removed at some point in the future.
+	 */
+	if (check_amd_hwpstate_cpu(0)) {
+		struct freq_attr **iter;
+
+		pr_debug("adding sysfs entry for cpb\n");
+
+		for (iter = acpi_cpufreq_attr; *iter != NULL; iter++)
+			;
+
+		/* make sure there is a terminator behind it */
+		if (iter[1] == NULL)
+			*iter = &cpb;
+	}
+#endif
+
 	ret = cpufreq_register_driver(&acpi_cpufreq_driver);
 	if (ret)
 		free_acpi_perf_data();
+	else
+		acpi_cpufreq_boost_init();
 
 	return ret;
 }
@@ -757,6 +1015,8 @@ static void __exit acpi_cpufreq_exit(void)
 {
 	pr_debug("acpi_cpufreq_exit\n");
 
+	acpi_cpufreq_boost_exit();
+
 	cpufreq_unregister_driver(&acpi_cpufreq_driver);
 
 	free_acpi_perf_data();

drivers/cpufreq/cpufreq-cpu0.c

@@ -0,0 +1,269 @@
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * The OPP code in function cpu0_set_target() is reused from
+ * drivers/cpufreq/omap-cpufreq.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt
+
+#include <linux/clk.h>
+#include <linux/cpu.h>
+#include <linux/cpufreq.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/opp.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+static unsigned int transition_latency;
+static unsigned int voltage_tolerance; /* in percentage */
+
+static struct device *cpu_dev;
+static struct clk *cpu_clk;
+static struct regulator *cpu_reg;
+static struct cpufreq_frequency_table *freq_table;
+
+static int cpu0_verify_speed(struct cpufreq_policy *policy)
+{
+	return cpufreq_frequency_table_verify(policy, freq_table);
+}
+
+static unsigned int cpu0_get_speed(unsigned int cpu)
+{
+	return clk_get_rate(cpu_clk) / 1000;
+}
+
+static int cpu0_set_target(struct cpufreq_policy *policy,
+			   unsigned int target_freq, unsigned int relation)
+{
+	struct cpufreq_freqs freqs;
+	struct opp *opp;
+	unsigned long freq_Hz, volt = 0, volt_old = 0, tol = 0;
+	unsigned int index, cpu;
+	int ret;
+
+	ret = cpufreq_frequency_table_target(policy, freq_table, target_freq,
+					     relation, &index);
+	if (ret) {
+		pr_err("failed to match target freqency %d: %d\n",
+		       target_freq, ret);
+		return ret;
+	}
+
+	freq_Hz = clk_round_rate(cpu_clk, freq_table[index].frequency * 1000);
+	if (freq_Hz < 0)
+		freq_Hz = freq_table[index].frequency * 1000;
+	freqs.new = freq_Hz / 1000;
+	freqs.old = clk_get_rate(cpu_clk) / 1000;
+
+	if (freqs.old == freqs.new)
+		return 0;
+
+	for_each_online_cpu(cpu) {
+		freqs.cpu = cpu;
+		cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+	}
+
+	if (cpu_reg) {
+		opp = opp_find_freq_ceil(cpu_dev, &freq_Hz);
+		if (IS_ERR(opp)) {
+			pr_err("failed to find OPP for %ld\n", freq_Hz);
+			return PTR_ERR(opp);
+		}
+		volt = opp_get_voltage(opp);
+		tol = volt * voltage_tolerance / 100;
+		volt_old = regulator_get_voltage(cpu_reg);
+	}
+
+	pr_debug("%u MHz, %ld mV --> %u MHz, %ld mV\n",
+		 freqs.old / 1000, volt_old ? volt_old / 1000 : -1,
+		 freqs.new / 1000, volt ? volt / 1000 : -1);
+
+	/* scaling up?  scale voltage before frequency */
+	if (cpu_reg && freqs.new > freqs.old) {
+		ret = regulator_set_voltage_tol(cpu_reg, volt, tol);
+		if (ret) {
+			pr_err("failed to scale voltage up: %d\n", ret);
+			freqs.new = freqs.old;
+			return ret;
+		}
+	}
+
+	ret = clk_set_rate(cpu_clk, freqs.new * 1000);
+	if (ret) {
+		pr_err("failed to set clock rate: %d\n", ret);
+		if (cpu_reg)
+			regulator_set_voltage_tol(cpu_reg, volt_old, tol);
+		return ret;
+	}
+
+	/* scaling down?  scale voltage after frequency */
+	if (cpu_reg && freqs.new < freqs.old) {
+		ret = regulator_set_voltage_tol(cpu_reg, volt, tol);
+		if (ret) {
+			pr_err("failed to scale voltage down: %d\n", ret);
+			clk_set_rate(cpu_clk, freqs.old * 1000);
+			freqs.new = freqs.old;
+			return ret;
+		}
+	}
+
+	for_each_online_cpu(cpu) {
+		freqs.cpu = cpu;
+		cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+	}
+
+	return 0;
+}
+
+static int cpu0_cpufreq_init(struct cpufreq_policy *policy)
+{
+	int ret;
+
+	if (policy->cpu != 0)
+		return -EINVAL;
+
+	ret = cpufreq_frequency_table_cpuinfo(policy, freq_table);
+	if (ret) {
+		pr_err("invalid frequency table: %d\n", ret);
+		return ret;
+	}
+
+	policy->cpuinfo.transition_latency = transition_latency;
+	policy->cur = clk_get_rate(cpu_clk) / 1000;
+
+	/*
+	 * The driver only supports the SMP configuartion where all processors
+	 * share the clock and voltage and clock.  Use cpufreq affected_cpus
+	 * interface to have all CPUs scaled together.
+	 */
+	policy->shared_type = CPUFREQ_SHARED_TYPE_ANY;
+	cpumask_setall(policy->cpus);
+
+	cpufreq_frequency_table_get_attr(freq_table, policy->cpu);
+
+	return 0;
+}
+
+static int cpu0_cpufreq_exit(struct cpufreq_policy *policy)
+{
+	cpufreq_frequency_table_put_attr(policy->cpu);
+
+	return 0;
+}
+
+static struct freq_attr *cpu0_cpufreq_attr[] = {
+	&cpufreq_freq_attr_scaling_available_freqs,
+	NULL,
+};
+
+static struct cpufreq_driver cpu0_cpufreq_driver = {
+	.flags = CPUFREQ_STICKY,
+	.verify = cpu0_verify_speed,
+	.target = cpu0_set_target,
+	.get = cpu0_get_speed,
+	.init = cpu0_cpufreq_init,
+	.exit = cpu0_cpufreq_exit,
+	.name = "generic_cpu0",
+	.attr = cpu0_cpufreq_attr,
+};
+
+static int __devinit cpu0_cpufreq_driver_init(void)
+{
+	struct device_node *np;
+	int ret;
+
+	np = of_find_node_by_path("/cpus/cpu@0");
+	if (!np) {
+		pr_err("failed to find cpu0 node\n");
+		return -ENOENT;
+	}
+
+	cpu_dev = get_cpu_device(0);
+	if (!cpu_dev) {
+		pr_err("failed to get cpu0 device\n");
+		ret = -ENODEV;
+		goto out_put_node;
+	}
+
+	cpu_dev->of_node = np;
+
+	cpu_clk = clk_get(cpu_dev, NULL);
+	if (IS_ERR(cpu_clk)) {
+		ret = PTR_ERR(cpu_clk);
+		pr_err("failed to get cpu0 clock: %d\n", ret);
+		goto out_put_node;
+	}
+
+	cpu_reg = regulator_get(cpu_dev, "cpu0");
+	if (IS_ERR(cpu_reg)) {
+		pr_warn("failed to get cpu0 regulator\n");
+		cpu_reg = NULL;
+	}
+
+	ret = of_init_opp_table(cpu_dev);
+	if (ret) {
+		pr_err("failed to init OPP table: %d\n", ret);
+		goto out_put_node;
+	}
+
+	ret = opp_init_cpufreq_table(cpu_dev, &freq_table);
+	if (ret) {
+		pr_err("failed to init cpufreq table: %d\n", ret);
+		goto out_put_node;
+	}
+
+	of_property_read_u32(np, "voltage-tolerance", &voltage_tolerance);
+
+	if (of_property_read_u32(np, "clock-latency", &transition_latency))
+		transition_latency = CPUFREQ_ETERNAL;
+
+	if (cpu_reg) {
+		struct opp *opp;
+		unsigned long min_uV, max_uV;
+		int i;
+
+		/*
+		 * OPP is maintained in order of increasing frequency, and
+		 * freq_table initialised from OPP is therefore sorted in the
+		 * same order.
+		 */
+		for (i = 0; freq_table[i].frequency != CPUFREQ_TABLE_END; i++)
+			;
+		opp = opp_find_freq_exact(cpu_dev,
+				freq_table[0].frequency * 1000, true);
+		min_uV = opp_get_voltage(opp);
+		opp = opp_find_freq_exact(cpu_dev,
+				freq_table[i-1].frequency * 1000, true);
+		max_uV = opp_get_voltage(opp);
+		ret = regulator_set_voltage_time(cpu_reg, min_uV, max_uV);
+		if (ret > 0)
+			transition_latency += ret * 1000;
+	}
+
+	ret = cpufreq_register_driver(&cpu0_cpufreq_driver);
+	if (ret) {
+		pr_err("failed register driver: %d\n", ret);
+		goto out_free_table;
+	}
+
+	of_node_put(np);
+	return 0;
+
+out_free_table:
+	opp_free_cpufreq_table(cpu_dev, &freq_table);
+out_put_node:
+	of_node_put(np);
+	return ret;
+}
+late_initcall(cpu0_cpufreq_driver_init);
+
+MODULE_AUTHOR("Shawn Guo <shawn.guo@linaro.org>");
+MODULE_DESCRIPTION("Generic CPU0 cpufreq driver");
+MODULE_LICENSE("GPL");

drivers/cpufreq/cpufreq_conservative.c

@@ -504,6 +504,7 @@ static int cpufreq_governor_dbs(struct cpufreq_policy *policy,
 				j_dbs_info->prev_cpu_nice =
 						kcpustat_cpu(j).cpustat[CPUTIME_NICE];
 		}
+		this_dbs_info->cpu = cpu;
 		this_dbs_info->down_skip = 0;
 		this_dbs_info->requested_freq = policy->cur;
 
@@ -583,6 +584,7 @@ static int cpufreq_governor_dbs(struct cpufreq_policy *policy,
 			__cpufreq_driver_target(
 					this_dbs_info->cur_policy,
 					policy->min, CPUFREQ_RELATION_L);
+		dbs_check_cpu(this_dbs_info);
 		mutex_unlock(&this_dbs_info->timer_mutex);
 
 		break;

drivers/cpufreq/cpufreq_ondemand.c

@@ -761,6 +761,7 @@ static int cpufreq_governor_dbs(struct cpufreq_policy *policy,
 		else if (policy->min > this_dbs_info->cur_policy->cur)
 			__cpufreq_driver_target(this_dbs_info->cur_policy,
 				policy->min, CPUFREQ_RELATION_L);
+		dbs_check_cpu(this_dbs_info);
 		mutex_unlock(&this_dbs_info->timer_mutex);
 		break;
 	}

drivers/cpufreq/longhaul.h

@@ -56,7 +56,7 @@ union msr_longhaul {
 /*
  * VIA C3 Samuel 1  & Samuel 2 (stepping 0)
  */
-static const int __cpuinitdata samuel1_mults[16] = {
+static const int __cpuinitconst samuel1_mults[16] = {
 	-1, /* 0000 -> RESERVED */
 	30, /* 0001 ->  3.0x */
 	40, /* 0010 ->  4.0x */
@@ -75,7 +75,7 @@ static const int __cpuinitdata samuel1_mults[16] = {
 	-1, /* 1111 -> RESERVED */
 };
 
-static const int __cpuinitdata samuel1_eblcr[16] = {
+static const int __cpuinitconst samuel1_eblcr[16] = {
 	50, /* 0000 -> RESERVED */
 	30, /* 0001 ->  3.0x */
 	40, /* 0010 ->  4.0x */
@@ -97,7 +97,7 @@ static const int __cpuinitdata samuel1_eblcr[16] = {
 /*
  * VIA C3 Samuel2 Stepping 1->15
  */
-static const int __cpuinitdata samuel2_eblcr[16] = {
+static const int __cpuinitconst samuel2_eblcr[16] = {
 	50,  /* 0000 ->  5.0x */
 	30,  /* 0001 ->  3.0x */
 	40,  /* 0010 ->  4.0x */
@@ -119,7 +119,7 @@ static const int __cpuinitdata samuel2_eblcr[16] = {
 /*
  * VIA C3 Ezra
  */
-static const int __cpuinitdata ezra_mults[16] = {
+static const int __cpuinitconst ezra_mults[16] = {
 	100, /* 0000 -> 10.0x */
 	30,  /* 0001 ->  3.0x */
 	40,  /* 0010 ->  4.0x */
@@ -138,7 +138,7 @@ static const int __cpuinitdata ezra_mults[16] = {
 	120, /* 1111 -> 12.0x */
 };
 
-static const int __cpuinitdata ezra_eblcr[16] = {
+static const int __cpuinitconst ezra_eblcr[16] = {
 	50,  /* 0000 ->  5.0x */
 	30,  /* 0001 ->  3.0x */
 	40,  /* 0010 ->  4.0x */
@@ -160,7 +160,7 @@ static const int __cpuinitdata ezra_eblcr[16] = {
 /*
  * VIA C3 (Ezra-T) [C5M].
  */
-static const int __cpuinitdata ezrat_mults[32] = {
+static const int __cpuinitconst ezrat_mults[32] = {
 	100, /* 0000 -> 10.0x */
 	30,  /* 0001 ->  3.0x */
 	40,  /* 0010 ->  4.0x */
@@ -196,7 +196,7 @@ static const int __cpuinitdata ezrat_mults[32] = {
 	-1,  /* 1111 -> RESERVED (12.0x) */
 };
 
-static const int __cpuinitdata ezrat_eblcr[32] = {
+static const int __cpuinitconst ezrat_eblcr[32] = {
 	50,  /* 0000 ->  5.0x */
 	30,  /* 0001 ->  3.0x */
 	40,  /* 0010 ->  4.0x */
@@ -235,7 +235,7 @@ static const int __cpuinitdata ezrat_eblcr[32] = {
 /*
  * VIA C3 Nehemiah */
 
-static const int __cpuinitdata nehemiah_mults[32] = {
+static const int __cpuinitconst nehemiah_mults[32] = {
 	100, /* 0000 -> 10.0x */
 	-1, /* 0001 -> 16.0x */
 	40,  /* 0010 ->  4.0x */
@@ -270,7 +270,7 @@ static const int __cpuinitdata nehemiah_mults[32] = {
 	-1, /* 1111 -> 12.0x */
 };
 
-static const int __cpuinitdata nehemiah_eblcr[32] = {
+static const int __cpuinitconst nehemiah_eblcr[32] = {
 	50,  /* 0000 ->  5.0x */
 	160, /* 0001 -> 16.0x */
 	40,  /* 0010 ->  4.0x */
@@ -315,7 +315,7 @@ struct mV_pos {
 	unsigned short pos;
 };
 
-static const struct mV_pos __cpuinitdata vrm85_mV[32] = {
+static const struct mV_pos __cpuinitconst vrm85_mV[32] = {
 	{1250, 8},	{1200, 6},	{1150, 4},	{1100, 2},
 	{1050, 0},	{1800, 30},	{1750, 28},	{1700, 26},
 	{1650, 24},	{1600, 22},	{1550, 20},	{1500, 18},
@@ -326,14 +326,14 @@ static const struct mV_pos __cpuinitdata vrm85_mV[32] = {
 	{1475, 17},	{1425, 15},	{1375, 13},	{1325, 11}
 };
 
-static const unsigned char __cpuinitdata mV_vrm85[32] = {
+static const unsigned char __cpuinitconst mV_vrm85[32] = {
 	0x04,	0x14,	0x03,	0x13,	0x02,	0x12,	0x01,	0x11,
 	0x00,	0x10,	0x0f,	0x1f,	0x0e,	0x1e,	0x0d,	0x1d,
 	0x0c,	0x1c,	0x0b,	0x1b,	0x0a,	0x1a,	0x09,	0x19,
 	0x08,	0x18,	0x07,	0x17,	0x06,	0x16,	0x05,	0x15
 };
 
-static const struct mV_pos __cpuinitdata mobilevrm_mV[32] = {
+static const struct mV_pos __cpuinitconst mobilevrm_mV[32] = {
 	{1750, 31},	{1700, 30},	{1650, 29},	{1600, 28},
 	{1550, 27},	{1500, 26},	{1450, 25},	{1400, 24},
 	{1350, 23},	{1300, 22},	{1250, 21},	{1200, 20},
@@ -344,7 +344,7 @@ static const struct mV_pos __cpuinitdata mobilevrm_mV[32] = {
 	{675, 3},	{650, 2},	{625, 1},	{600, 0}
 };
 
-static const unsigned char __cpuinitdata mV_mobilevrm[32] = {
+static const unsigned char __cpuinitconst mV_mobilevrm[32] = {
 	0x1f,	0x1e,	0x1d,	0x1c,	0x1b,	0x1a,	0x19,	0x18,
 	0x17,	0x16,	0x15,	0x14,	0x13,	0x12,	0x11,	0x10,
 	0x0f,	0x0e,	0x0d,	0x0c,	0x0b,	0x0a,	0x09,	0x08,

drivers/cpufreq/omap-cpufreq.c

@@ -40,16 +40,6 @@
 /* OPP tolerance in percentage */
 #define	OPP_TOLERANCE	4
 
-#ifdef CONFIG_SMP
-struct lpj_info {
-	unsigned long	ref;
-	unsigned int	freq;
-};
-
-static DEFINE_PER_CPU(struct lpj_info, lpj_ref);
-static struct lpj_info global_lpj_ref;
-#endif
-
 static struct cpufreq_frequency_table *freq_table;
 static atomic_t freq_table_users = ATOMIC_INIT(0);
 static struct clk *mpu_clk;
@@ -161,31 +151,6 @@ static int omap_target(struct cpufreq_policy *policy,
 	}
 
 	freqs.new = omap_getspeed(policy->cpu);
-#ifdef CONFIG_SMP
-	/*
-	 * Note that loops_per_jiffy is not updated on SMP systems in
-	 * cpufreq driver. So, update the per-CPU loops_per_jiffy value
-	 * on frequency transition. We need to update all dependent CPUs.
-	 */
-	for_each_cpu(i, policy->cpus) {
-		struct lpj_info *lpj = &per_cpu(lpj_ref, i);
-		if (!lpj->freq) {
-			lpj->ref = per_cpu(cpu_data, i).loops_per_jiffy;
-			lpj->freq = freqs.old;
-		}
-
-		per_cpu(cpu_data, i).loops_per_jiffy =
-			cpufreq_scale(lpj->ref, lpj->freq, freqs.new);
-	}
-
-	/* And don't forget to adjust the global one */
-	if (!global_lpj_ref.freq) {
-		global_lpj_ref.ref = loops_per_jiffy;
-		global_lpj_ref.freq = freqs.old;
-	}
-	loops_per_jiffy = cpufreq_scale(global_lpj_ref.ref, global_lpj_ref.freq,
-					freqs.new);
-#endif
 
 done:
 	/* notifiers */

drivers/cpufreq/powernow-k8.c

@@ -49,22 +49,12 @@
 #define PFX "powernow-k8: "
 #define VERSION "version 2.20.00"
 #include "powernow-k8.h"
-#include "mperf.h"
 
 /* serialize freq changes  */
 static DEFINE_MUTEX(fidvid_mutex);
 
 static DEFINE_PER_CPU(struct powernow_k8_data *, powernow_data);
 
-static int cpu_family = CPU_OPTERON;
-
-/* array to map SW pstate number to acpi state */
-static u32 ps_to_as[8];
-
-/* core performance boost */
-static bool cpb_capable, cpb_enabled;
-static struct msr __percpu *msrs;
-
 static struct cpufreq_driver cpufreq_amd64_driver;
 
 #ifndef CONFIG_SMP
@@ -86,12 +76,6 @@ static u32 find_khz_freq_from_fid(u32 fid)
 	return 1000 * find_freq_from_fid(fid);
 }
 
-static u32 find_khz_freq_from_pstate(struct cpufreq_frequency_table *data,
-				     u32 pstate)
-{
-	return data[ps_to_as[pstate]].frequency;
-}
-
 /* Return the vco fid for an input fid
  *
  * Each "low" fid has corresponding "high" fid, and you can get to "low" fids
@@ -114,9 +98,6 @@ static int pending_bit_stuck(void)
 {
 	u32 lo, hi;
 
-	if (cpu_family == CPU_HW_PSTATE)
-		return 0;
-
 	rdmsr(MSR_FIDVID_STATUS, lo, hi);
 	return lo & MSR_S_LO_CHANGE_PENDING ? 1 : 0;
 }
@@ -130,20 +111,6 @@ static int query_current_values_with_pending_wait(struct powernow_k8_data *data)
 	u32 lo, hi;
 	u32 i = 0;
 
-	if (cpu_family == CPU_HW_PSTATE) {
-		rdmsr(MSR_PSTATE_STATUS, lo, hi);
-		i = lo & HW_PSTATE_MASK;
-		data->currpstate = i;
-
-		/*
-		 * a workaround for family 11h erratum 311 might cause
-		 * an "out-of-range Pstate if the core is in Pstate-0
-		 */
-		if ((boot_cpu_data.x86 == 0x11) && (i >= data->numps))
-			data->currpstate = HW_PSTATE_0;
-
-		return 0;
-	}
 	do {
 		if (i++ > 10000) {
 			pr_debug("detected change pending stuck\n");
@@ -300,14 +267,6 @@ static int decrease_vid_code_by_step(struct powernow_k8_data *data,
 	return 0;
 }
 
-/* Change hardware pstate by single MSR write */
-static int transition_pstate(struct powernow_k8_data *data, u32 pstate)
-{
-	wrmsr(MSR_PSTATE_CTRL, pstate, 0);
-	data->currpstate = pstate;
-	return 0;
-}
-
 /* Change Opteron/Athlon64 fid and vid, by the 3 phases. */
 static int transition_fid_vid(struct powernow_k8_data *data,
 		u32 reqfid, u32 reqvid)
@@ -524,8 +483,6 @@ static int core_voltage_post_transition(struct powernow_k8_data *data,
 static const struct x86_cpu_id powernow_k8_ids[] = {
 	/* IO based frequency switching */
 	{ X86_VENDOR_AMD, 0xf },
-	/* MSR based frequency switching supported */
-	X86_FEATURE_MATCH(X86_FEATURE_HW_PSTATE),
 	{}
 };
 MODULE_DEVICE_TABLE(x86cpu, powernow_k8_ids);
@@ -561,15 +518,8 @@ static void check_supported_cpu(void *_rc)
 				"Power state transitions not supported\n");
 			return;
 		}
-	} else { /* must be a HW Pstate capable processor */
-		cpuid(CPUID_FREQ_VOLT_CAPABILITIES, &eax, &ebx, &ecx, &edx);
-		if ((edx & USE_HW_PSTATE) == USE_HW_PSTATE)
-			cpu_family = CPU_HW_PSTATE;
-		else
-			return;
+		*rc = 0;
 	}
-
-	*rc = 0;
 }
 
 static int check_pst_table(struct powernow_k8_data *data, struct pst_s *pst,
@@ -633,18 +583,11 @@ static void print_basics(struct powernow_k8_data *data)
 	for (j = 0; j < data->numps; j++) {
 		if (data->powernow_table[j].frequency !=
 				CPUFREQ_ENTRY_INVALID) {
-			if (cpu_family == CPU_HW_PSTATE) {
-				printk(KERN_INFO PFX
-					"   %d : pstate %d (%d MHz)\n", j,
-					data->powernow_table[j].index,
-					data->powernow_table[j].frequency/1000);
-			} else {
 				printk(KERN_INFO PFX
 					"fid 0x%x (%d MHz), vid 0x%x\n",
 					data->powernow_table[j].index & 0xff,
 					data->powernow_table[j].frequency/1000,
 					data->powernow_table[j].index >> 8);
-			}
 		}
 	}
 	if (data->batps)
@@ -652,20 +595,6 @@ static void print_basics(struct powernow_k8_data *data)
 				data->batps);
 }
 
-static u32 freq_from_fid_did(u32 fid, u32 did)
-{
-	u32 mhz = 0;
-
-	if (boot_cpu_data.x86 == 0x10)
-		mhz = (100 * (fid + 0x10)) >> did;
-	else if (boot_cpu_data.x86 == 0x11)
-		mhz = (100 * (fid + 8)) >> did;
-	else
-		BUG();
-
-	return mhz * 1000;
-}
-
 static int fill_powernow_table(struct powernow_k8_data *data,
 		struct pst_s *pst, u8 maxvid)
 {
@@ -825,7 +754,7 @@ static void powernow_k8_acpi_pst_values(struct powernow_k8_data *data,
 {
 	u64 control;
 
-	if (!data->acpi_data.state_count || (cpu_family == CPU_HW_PSTATE))
+	if (!data->acpi_data.state_count)
 		return;
 
 	control = data->acpi_data.states[index].control;
@@ -876,10 +805,7 @@ static int powernow_k8_cpu_init_acpi(struct powernow_k8_data *data)
 	data->numps = data->acpi_data.state_count;
 	powernow_k8_acpi_pst_values(data, 0);
 
-	if (cpu_family == CPU_HW_PSTATE)
-		ret_val = fill_powernow_table_pstate(data, powernow_table);
-	else
-		ret_val = fill_powernow_table_fidvid(data, powernow_table);
+	ret_val = fill_powernow_table_fidvid(data, powernow_table);
 	if (ret_val)
 		goto err_out_mem;
 
@@ -916,51 +842,6 @@ err_out:
 	return ret_val;
 }
 
-static int fill_powernow_table_pstate(struct powernow_k8_data *data,
-		struct cpufreq_frequency_table *powernow_table)
-{
-	int i;
-	u32 hi = 0, lo = 0;
-	rdmsr(MSR_PSTATE_CUR_LIMIT, lo, hi);
-	data->max_hw_pstate = (lo & HW_PSTATE_MAX_MASK) >> HW_PSTATE_MAX_SHIFT;
-
-	for (i = 0; i < data->acpi_data.state_count; i++) {
-		u32 index;
-
-		index = data->acpi_data.states[i].control & HW_PSTATE_MASK;
-		if (index > data->max_hw_pstate) {
-			printk(KERN_ERR PFX "invalid pstate %d - "
-					"bad value %d.\n", i, index);
-			printk(KERN_ERR PFX "Please report to BIOS "
-					"manufacturer\n");
-			invalidate_entry(powernow_table, i);
-			continue;
-		}
-
-		ps_to_as[index] = i;
-
-		/* Frequency may be rounded for these */
-		if ((boot_cpu_data.x86 == 0x10 && boot_cpu_data.x86_model < 10)
-				 || boot_cpu_data.x86 == 0x11) {
-
-			rdmsr(MSR_PSTATE_DEF_BASE + index, lo, hi);
-			if (!(hi & HW_PSTATE_VALID_MASK)) {
-				pr_debug("invalid pstate %d, ignoring\n", index);
-				invalidate_entry(powernow_table, i);
-				continue;
-			}
-
-			powernow_table[i].frequency =
-				freq_from_fid_did(lo & 0x3f, (lo >> 6) & 7);
-		} else
-			powernow_table[i].frequency =
-				data->acpi_data.states[i].core_frequency * 1000;
-
-		powernow_table[i].index = index;
-	}
-	return 0;
-}
-
 static int fill_powernow_table_fidvid(struct powernow_k8_data *data,
 		struct cpufreq_frequency_table *powernow_table)
 {
@@ -1037,15 +918,7 @@ static int get_transition_latency(struct powernow_k8_data *data)
 			max_latency = cur_latency;
 	}
 	if (max_latency == 0) {
-		/*
-		 * Fam 11h and later may return 0 as transition latency. This
-		 * is intended and means "very fast". While cpufreq core and
-		 * governors currently can handle that gracefully, better set it
-		 * to 1 to avoid problems in the future.
-		 */
-		if (boot_cpu_data.x86 < 0x11)
-			printk(KERN_ERR FW_WARN PFX "Invalid zero transition "
-				"latency\n");
+		pr_err(FW_WARN PFX "Invalid zero transition latency\n");
 		max_latency = 1;
 	}
 	/* value in usecs, needs to be in nanoseconds */
@@ -1105,40 +978,6 @@ static int transition_frequency_fidvid(struct powernow_k8_data *data,
 	return res;
 }
 
-/* Take a frequency, and issue the hardware pstate transition command */
-static int transition_frequency_pstate(struct powernow_k8_data *data,
-		unsigned int index)
-{
-	u32 pstate = 0;
-	int res, i;
-	struct cpufreq_freqs freqs;
-
-	pr_debug("cpu %d transition to index %u\n", smp_processor_id(), index);
-
-	/* get MSR index for hardware pstate transition */
-	pstate = index & HW_PSTATE_MASK;
-	if (pstate > data->max_hw_pstate)
-		return -EINVAL;
-
-	freqs.old = find_khz_freq_from_pstate(data->powernow_table,
-			data->currpstate);
-	freqs.new = find_khz_freq_from_pstate(data->powernow_table, pstate);
-
-	for_each_cpu(i, data->available_cores) {
-		freqs.cpu = i;
-		cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
-	}
-
-	res = transition_pstate(data, pstate);
-	freqs.new = find_khz_freq_from_pstate(data->powernow_table, pstate);
-
-	for_each_cpu(i, data->available_cores) {
-		freqs.cpu = i;
-		cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
-	}
-	return res;
-}
-
 /* Driver entry point to switch to the target frequency */
 static int powernowk8_target(struct cpufreq_policy *pol,
 		unsigned targfreq, unsigned relation)
@@ -1180,18 +1019,15 @@ static int powernowk8_target(struct cpufreq_policy *pol,
 	if (query_current_values_with_pending_wait(data))
 		goto err_out;
 
-	if (cpu_family != CPU_HW_PSTATE) {
-		pr_debug("targ: curr fid 0x%x, vid 0x%x\n",
-		data->currfid, data->currvid);
+	pr_debug("targ: curr fid 0x%x, vid 0x%x\n",
+		 data->currfid, data->currvid);
 
-		if ((checkvid != data->currvid) ||
-		    (checkfid != data->currfid)) {
-			printk(KERN_INFO PFX
-				"error - out of sync, fix 0x%x 0x%x, "
-				"vid 0x%x 0x%x\n",
-				checkfid, data->currfid,
-				checkvid, data->currvid);
-		}
+	if ((checkvid != data->currvid) ||
+	    (checkfid != data->currfid)) {
+		pr_info(PFX
+		       "error - out of sync, fix 0x%x 0x%x, vid 0x%x 0x%x\n",
+		       checkfid, data->currfid,
+		       checkvid, data->currvid);
 	}
 
 	if (cpufreq_frequency_table_target(pol, data->powernow_table,
@@ -1202,11 +1038,8 @@ static int powernowk8_target(struct cpufreq_policy *pol,
 
 	powernow_k8_acpi_pst_values(data, newstate);
 
-	if (cpu_family == CPU_HW_PSTATE)
-		ret = transition_frequency_pstate(data,
-			data->powernow_table[newstate].index);
-	else
-		ret = transition_frequency_fidvid(data, newstate);
+	ret = transition_frequency_fidvid(data, newstate);
+
 	if (ret) {
 		printk(KERN_ERR PFX "transition frequency failed\n");
 		ret = 1;
@@ -1215,11 +1048,7 @@ static int powernowk8_target(struct cpufreq_policy *pol,
 	}
 	mutex_unlock(&fidvid_mutex);
 
-	if (cpu_family == CPU_HW_PSTATE)
-		pol->cur = find_khz_freq_from_pstate(data->powernow_table,
-				data->powernow_table[newstate].index);
-	else
-		pol->cur = find_khz_freq_from_fid(data->currfid);
+	pol->cur = find_khz_freq_from_fid(data->currfid);
 	ret = 0;
 
 err_out:
@@ -1259,22 +1088,23 @@ static void __cpuinit powernowk8_cpu_init_on_cpu(void *_init_on_cpu)
 		return;
 	}
 
-	if (cpu_family == CPU_OPTERON)
-		fidvid_msr_init();
+	fidvid_msr_init();
 
 	init_on_cpu->rc = 0;
 }
 
+static const char missing_pss_msg[] =
+	KERN_ERR
+	FW_BUG PFX "No compatible ACPI _PSS objects found.\n"
+	FW_BUG PFX "First, make sure Cool'N'Quiet is enabled in the BIOS.\n"
+	FW_BUG PFX "If that doesn't help, try upgrading your BIOS.\n";
+
 /* per CPU init entry point to the driver */
 static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol)
 {
-	static const char ACPI_PSS_BIOS_BUG_MSG[] =
-		KERN_ERR FW_BUG PFX "No compatible ACPI _PSS objects found.\n"
-		FW_BUG PFX "Try again with latest BIOS.\n";
 	struct powernow_k8_data *data;
 	struct init_on_cpu init_on_cpu;
 	int rc;
-	struct cpuinfo_x86 *c = &cpu_data(pol->cpu);
 
 	if (!cpu_online(pol->cpu))
 		return -ENODEV;
@@ -1290,7 +1120,6 @@ static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol)
 	}
 
 	data->cpu = pol->cpu;
-	data->currpstate = HW_PSTATE_INVALID;
 
 	if (powernow_k8_cpu_init_acpi(data)) {
 		/*
@@ -1298,7 +1127,7 @@ static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol)
 		 * an UP version, and is deprecated by AMD.
 		 */
 		if (num_online_cpus() != 1) {
-			printk_once(ACPI_PSS_BIOS_BUG_MSG);
+			printk_once(missing_pss_msg);
 			goto err_out;
 		}
 		if (pol->cpu != 0) {
@@ -1327,17 +1156,10 @@ static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol)
 	if (rc != 0)
 		goto err_out_exit_acpi;
 
-	if (cpu_family == CPU_HW_PSTATE)
-		cpumask_copy(pol->cpus, cpumask_of(pol->cpu));
-	else
-		cpumask_copy(pol->cpus, cpu_core_mask(pol->cpu));
+	cpumask_copy(pol->cpus, cpu_core_mask(pol->cpu));
 	data->available_cores = pol->cpus;
 
-	if (cpu_family == CPU_HW_PSTATE)
-		pol->cur = find_khz_freq_from_pstate(data->powernow_table,
-				data->currpstate);
-	else
-		pol->cur = find_khz_freq_from_fid(data->currfid);
+	pol->cur = find_khz_freq_from_fid(data->currfid);
 	pr_debug("policy current frequency %d kHz\n", pol->cur);
 
 	/* min/max the cpu is capable of */
@@ -1349,18 +1171,10 @@ static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol)
 		return -EINVAL;
 	}
 
-	/* Check for APERF/MPERF support in hardware */
-	if (cpu_has(c, X86_FEATURE_APERFMPERF))
-		cpufreq_amd64_driver.getavg = cpufreq_get_measured_perf;
-
 	cpufreq_frequency_table_get_attr(data->powernow_table, pol->cpu);
 
-	if (cpu_family == CPU_HW_PSTATE)
-		pr_debug("cpu_init done, current pstate 0x%x\n",
-				data->currpstate);
-	else
-		pr_debug("cpu_init done, current fid 0x%x, vid 0x%x\n",
-			data->currfid, data->currvid);
+	pr_debug("cpu_init done, current fid 0x%x, vid 0x%x\n",
+		 data->currfid, data->currvid);
 
 	per_cpu(powernow_data, pol->cpu) = data;
 
@@ -1413,88 +1227,15 @@ static unsigned int powernowk8_get(unsigned int cpu)
 	if (err)
 		goto out;
 
-	if (cpu_family == CPU_HW_PSTATE)
-		khz = find_khz_freq_from_pstate(data->powernow_table,
-						data->currpstate);
-	else
-		khz = find_khz_freq_from_fid(data->currfid);
+	khz = find_khz_freq_from_fid(data->currfid);
 
 
 out:
 	return khz;
 }
 
-static void _cpb_toggle_msrs(bool t)
-{
-	int cpu;
-
-	get_online_cpus();
-
-	rdmsr_on_cpus(cpu_online_mask, MSR_K7_HWCR, msrs);
-
-	for_each_cpu(cpu, cpu_online_mask) {
-		struct msr *reg = per_cpu_ptr(msrs, cpu);
-		if (t)
-			reg->l &= ~BIT(25);
-		else
-			reg->l |= BIT(25);
-	}
-	wrmsr_on_cpus(cpu_online_mask, MSR_K7_HWCR, msrs);
-
-	put_online_cpus();
-}
-
-/*
- * Switch on/off core performance boosting.
- *
- * 0=disable
- * 1=enable.
- */
-static void cpb_toggle(bool t)
-{
-	if (!cpb_capable)
-		return;
-
-	if (t && !cpb_enabled) {
-		cpb_enabled = true;
-		_cpb_toggle_msrs(t);
-		printk(KERN_INFO PFX "Core Boosting enabled.\n");
-	} else if (!t && cpb_enabled) {
-		cpb_enabled = false;
-		_cpb_toggle_msrs(t);
-		printk(KERN_INFO PFX "Core Boosting disabled.\n");
-	}
-}
-
-static ssize_t store_cpb(struct cpufreq_policy *policy, const char *buf,
-				 size_t count)
-{
-	int ret = -EINVAL;
-	unsigned long val = 0;
-
-	ret = strict_strtoul(buf, 10, &val);
-	if (!ret && (val == 0 || val == 1) && cpb_capable)
-		cpb_toggle(val);
-	else
-		return -EINVAL;
-
-	return count;
-}
-
-static ssize_t show_cpb(struct cpufreq_policy *policy, char *buf)
-{
-	return sprintf(buf, "%u\n", cpb_enabled);
-}
-
-#define define_one_rw(_name) \
-static struct freq_attr _name = \
-__ATTR(_name, 0644, show_##_name, store_##_name)
-
-define_one_rw(cpb);
-
 static struct freq_attr *powernow_k8_attr[] = {
 	&cpufreq_freq_attr_scaling_available_freqs,
-	&cpb,
 	NULL,
 };
 
@@ -1510,53 +1251,18 @@ static struct cpufreq_driver cpufreq_amd64_driver = {
 	.attr		= powernow_k8_attr,
 };
 
-/*
- * Clear the boost-disable flag on the CPU_DOWN path so that this cpu
- * cannot block the remaining ones from boosting. On the CPU_UP path we
- * simply keep the boost-disable flag in sync with the current global
- * state.
- */
-static int cpb_notify(struct notifier_block *nb, unsigned long action,
-		      void *hcpu)
-{
-	unsigned cpu = (long)hcpu;
-	u32 lo, hi;
-
-	switch (action) {
-	case CPU_UP_PREPARE:
-	case CPU_UP_PREPARE_FROZEN:
-
-		if (!cpb_enabled) {
-			rdmsr_on_cpu(cpu, MSR_K7_HWCR, &lo, &hi);
-			lo |= BIT(25);
-			wrmsr_on_cpu(cpu, MSR_K7_HWCR, lo, hi);
-		}
-		break;
-
-	case CPU_DOWN_PREPARE:
-	case CPU_DOWN_PREPARE_FROZEN:
-		rdmsr_on_cpu(cpu, MSR_K7_HWCR, &lo, &hi);
-		lo &= ~BIT(25);
-		wrmsr_on_cpu(cpu, MSR_K7_HWCR, lo, hi);
-		break;
-
-	default:
-		break;
-	}
-
-	return NOTIFY_OK;
-}
-
-static struct notifier_block cpb_nb = {
-	.notifier_call		= cpb_notify,
-};
-
 /* driver entry point for init */
 static int __cpuinit powernowk8_init(void)
 {
-	unsigned int i, supported_cpus = 0, cpu;
+	unsigned int i, supported_cpus = 0;
 	int rv;
 
+	if (static_cpu_has(X86_FEATURE_HW_PSTATE)) {
+		pr_warn(PFX "this CPU is not supported anymore, using acpi-cpufreq instead.\n");
+		request_module("acpi-cpufreq");
+		return -ENODEV;
+	}
+
 	if (!x86_match_cpu(powernow_k8_ids))
 		return -ENODEV;
 
@@ -1570,38 +1276,13 @@ static int __cpuinit powernowk8_init(void)
 	if (supported_cpus != num_online_cpus())
 		return -ENODEV;
 
-	printk(KERN_INFO PFX "Found %d %s (%d cpu cores) (" VERSION ")\n",
-		num_online_nodes(), boot_cpu_data.x86_model_id, supported_cpus);
-
-	if (boot_cpu_has(X86_FEATURE_CPB)) {
-
-		cpb_capable = true;
-
-		msrs = msrs_alloc();
-		if (!msrs) {
-			printk(KERN_ERR "%s: Error allocating msrs!\n", __func__);
-			return -ENOMEM;
-		}
-
-		register_cpu_notifier(&cpb_nb);
-
-		rdmsr_on_cpus(cpu_online_mask, MSR_K7_HWCR, msrs);
+	rv = cpufreq_register_driver(&cpufreq_amd64_driver);
 
-		for_each_cpu(cpu, cpu_online_mask) {
-			struct msr *reg = per_cpu_ptr(msrs, cpu);
-			cpb_enabled |= !(!!(reg->l & BIT(25)));
-		}
+	if (!rv)
+		pr_info(PFX "Found %d %s (%d cpu cores) (" VERSION ")\n",
+			num_online_nodes(), boot_cpu_data.x86_model_id,
+			supported_cpus);
 
-		printk(KERN_INFO PFX "Core Performance Boosting: %s.\n",
-			(cpb_enabled ? "on" : "off"));
-	}
-
-	rv = cpufreq_register_driver(&cpufreq_amd64_driver);
-	if (rv < 0 && boot_cpu_has(X86_FEATURE_CPB)) {
-		unregister_cpu_notifier(&cpb_nb);
-		msrs_free(msrs);
-		msrs = NULL;
-	}
 	return rv;
 }
 
@@ -1610,13 +1291,6 @@ static void __exit powernowk8_exit(void)
 {
 	pr_debug("exit\n");
 
-	if (boot_cpu_has(X86_FEATURE_CPB)) {
-		msrs_free(msrs);
-		msrs = NULL;
-
-		unregister_cpu_notifier(&cpb_nb);
-	}
-
 	cpufreq_unregister_driver(&cpufreq_amd64_driver);
 }
 

drivers/cpufreq/powernow-k8.h

@@ -5,24 +5,11 @@
  *  http://www.gnu.org/licenses/gpl.html
  */
 
-enum pstate {
-	HW_PSTATE_INVALID = 0xff,
-	HW_PSTATE_0 = 0,
-	HW_PSTATE_1 = 1,
-	HW_PSTATE_2 = 2,
-	HW_PSTATE_3 = 3,
-	HW_PSTATE_4 = 4,
-	HW_PSTATE_5 = 5,
-	HW_PSTATE_6 = 6,
-	HW_PSTATE_7 = 7,
-};
-
 struct powernow_k8_data {
 	unsigned int cpu;
 
 	u32 numps;  /* number of p-states */
 	u32 batps;  /* number of p-states supported on battery */
-	u32 max_hw_pstate; /* maximum legal hardware pstate */
 
 	/* these values are constant when the PSB is used to determine
 	 * vid/fid pairings, but are modified during the ->target() call
@@ -37,7 +24,6 @@ struct powernow_k8_data {
 	/* keep track of the current fid / vid or pstate */
 	u32 currvid;
 	u32 currfid;
-	enum pstate currpstate;
 
 	/* the powernow_table includes all frequency and vid/fid pairings:
 	 * fid are the lower 8 bits of the index, vid are the upper 8 bits.
@@ -97,23 +83,6 @@ struct powernow_k8_data {
 #define MSR_S_HI_CURRENT_VID      0x0000003f
 #define MSR_C_HI_STP_GNT_BENIGN	  0x00000001
 
-
-/* Hardware Pstate _PSS and MSR definitions */
-#define USE_HW_PSTATE		0x00000080
-#define HW_PSTATE_MASK 		0x00000007
-#define HW_PSTATE_VALID_MASK 	0x80000000
-#define HW_PSTATE_MAX_MASK	0x000000f0
-#define HW_PSTATE_MAX_SHIFT	4
-#define MSR_PSTATE_DEF_BASE 	0xc0010064 /* base of Pstate MSRs */
-#define MSR_PSTATE_STATUS 	0xc0010063 /* Pstate Status MSR */
-#define MSR_PSTATE_CTRL 	0xc0010062 /* Pstate control MSR */
-#define MSR_PSTATE_CUR_LIMIT	0xc0010061 /* pstate current limit MSR */
-
-/* define the two driver architectures */
-#define CPU_OPTERON 0
-#define CPU_HW_PSTATE 1
-
-
 /*
  * There are restrictions frequencies have to follow:
  * - only 1 entry in the low fid table ( <=1.4GHz )
@@ -218,5 +187,4 @@ static int core_frequency_transition(struct powernow_k8_data *data, u32 reqfid);
 
 static void powernow_k8_acpi_pst_values(struct powernow_k8_data *data, unsigned int index);
 
-static int fill_powernow_table_pstate(struct powernow_k8_data *data, struct cpufreq_frequency_table *powernow_table);
 static int fill_powernow_table_fidvid(struct powernow_k8_data *data, struct cpufreq_frequency_table *powernow_table);

include/linux/opp.h

@@ -48,6 +48,14 @@ int opp_disable(struct device *dev, unsigned long freq);
 
 struct srcu_notifier_head *opp_get_notifier(struct device *dev);
 
+#ifdef CONFIG_OF
+int of_init_opp_table(struct device *dev);
+#else
+static inline int of_init_opp_table(struct device *dev)
+{
+	return -EINVAL;
+}
+#endif /* CONFIG_OF */
 #else
 static inline unsigned long opp_get_voltage(struct opp *opp)
 {