Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x into fbdev-next

Conflicts:
	drivers/video/atmel_lcdfb.c

arch/powerpc/platforms/512x/mpc512x_shared.c

@@ -66,8 +66,8 @@ struct fsl_diu_shared_fb {
 	bool		in_use;
 };
 
-unsigned int mpc512x_get_pixel_format(unsigned int bits_per_pixel,
-				      int monitor_port)
+u32 mpc512x_get_pixel_format(enum fsl_diu_monitor_port port,
+			     unsigned int bits_per_pixel)
 {
 	switch (bits_per_pixel) {
 	case 32:
@@ -80,11 +80,12 @@ unsigned int mpc512x_get_pixel_format(unsigned int bits_per_pixel,
 	return 0x00000400;
 }
 
-void mpc512x_set_gamma_table(int monitor_port, char *gamma_table_base)
+void mpc512x_set_gamma_table(enum fsl_diu_monitor_port port,
+			     char *gamma_table_base)
 {
 }
 
-void mpc512x_set_monitor_port(int monitor_port)
+void mpc512x_set_monitor_port(enum fsl_diu_monitor_port port)
 {
 }
 
@@ -182,14 +183,10 @@ void mpc512x_set_pixel_clock(unsigned int pixclock)
 	iounmap(ccm);
 }
 
-ssize_t mpc512x_show_monitor_port(int monitor_port, char *buf)
+enum fsl_diu_monitor_port
+mpc512x_valid_monitor_port(enum fsl_diu_monitor_port port)
 {
-	return sprintf(buf, "0 - 5121 LCD\n");
-}
-
-int mpc512x_set_sysfs_monitor_port(int val)
-{
-	return 0;
+	return FSL_DIU_PORT_DVI;
 }
 
 static struct fsl_diu_shared_fb __attribute__ ((__aligned__(8))) diu_shared_fb;
@@ -332,8 +329,7 @@ void __init mpc512x_setup_diu(void)
 	diu_ops.set_gamma_table		= mpc512x_set_gamma_table;
 	diu_ops.set_monitor_port	= mpc512x_set_monitor_port;
 	diu_ops.set_pixel_clock		= mpc512x_set_pixel_clock;
-	diu_ops.show_monitor_port	= mpc512x_show_monitor_port;
-	diu_ops.set_sysfs_monitor_port	= mpc512x_set_sysfs_monitor_port;
+	diu_ops.valid_monitor_port	= mpc512x_valid_monitor_port;
 	diu_ops.release_bootmem		= mpc512x_release_bootmem;
 #endif
 }

arch/powerpc/platforms/85xx/p1022_ds.c

@@ -93,8 +93,8 @@
  * The Area Descriptor is a 32-bit value that determine which bits in each
  * pixel are to be used for each color.
  */
-static unsigned int p1022ds_get_pixel_format(unsigned int bits_per_pixel,
-	int monitor_port)
+static u32 p1022ds_get_pixel_format(enum fsl_diu_monitor_port port,
+				    unsigned int bits_per_pixel)
 {
 	switch (bits_per_pixel) {
 	case 32:
@@ -118,7 +118,8 @@ static unsigned int p1022ds_get_pixel_format(unsigned int bits_per_pixel,
  * On some boards, the gamma table for some ports may need to be modified.
  * This is not the case on the P1022DS, so we do nothing.
 */
-static void p1022ds_set_gamma_table(int monitor_port, char *gamma_table_base)
+static void p1022ds_set_gamma_table(enum fsl_diu_monitor_port port,
+				    char *gamma_table_base)
 {
 }
 
@@ -126,7 +127,7 @@ static void p1022ds_set_gamma_table(int monitor_port, char *gamma_table_base)
  * p1022ds_set_monitor_port: switch the output to a different monitor port
  *
  */
-static void p1022ds_set_monitor_port(int monitor_port)
+static void p1022ds_set_monitor_port(enum fsl_diu_monitor_port port)
 {
 	struct device_node *pixis_node;
 	void __iomem *pixis;
@@ -145,19 +146,21 @@ static void p1022ds_set_monitor_port(int monitor_port)
 	}
 	brdcfg1 = pixis + 9;	/* BRDCFG1 is at offset 9 in the ngPIXIS */
 
-	switch (monitor_port) {
-	case 0: /* DVI */
+	switch (port) {
+	case FSL_DIU_PORT_DVI:
+		printk(KERN_INFO "%s:%u\n", __func__, __LINE__);
 		/* Enable the DVI port, disable the DFP and the backlight */
 		clrsetbits_8(brdcfg1, PX_BRDCFG1_DFPEN | PX_BRDCFG1_BACKLIGHT,
 			     PX_BRDCFG1_DVIEN);
 		break;
-	case 1: /* Single link LVDS */
+	case FSL_DIU_PORT_LVDS:
+		printk(KERN_INFO "%s:%u\n", __func__, __LINE__);
 		/* Enable the DFP port, disable the DVI and the backlight */
 		clrsetbits_8(brdcfg1, PX_BRDCFG1_DVIEN | PX_BRDCFG1_BACKLIGHT,
 			     PX_BRDCFG1_DFPEN);
 		break;
 	default:
-		pr_err("p1022ds: unsupported monitor port %i\n", monitor_port);
+		pr_err("p1022ds: unsupported monitor port %i\n", port);
 	}
 
 	iounmap(pixis);
@@ -214,23 +217,18 @@ void p1022ds_set_pixel_clock(unsigned int pixclock)
 }
 
 /**
- * p1022ds_show_monitor_port: show the current monitor
- *
- * This function returns a string indicating whether the current monitor is
- * set to DVI or LVDS.
- */
-ssize_t p1022ds_show_monitor_port(int monitor_port, char *buf)
-{
-	return sprintf(buf, "%c0 - DVI\n%c1 - Single link LVDS\n",
-		monitor_port == 0 ? '*' : ' ', monitor_port == 1 ? '*' : ' ');
-}
-
-/**
- * p1022ds_set_sysfs_monitor_port: set the monitor port for sysfs
+ * p1022ds_valid_monitor_port: set the monitor port for sysfs
  */
-int p1022ds_set_sysfs_monitor_port(int val)
+enum fsl_diu_monitor_port
+p1022ds_valid_monitor_port(enum fsl_diu_monitor_port port)
 {
-	return val < 2 ? val : 0;
+	switch (port) {
+	case FSL_DIU_PORT_DVI:
+	case FSL_DIU_PORT_LVDS:
+		return port;
+	default:
+		return FSL_DIU_PORT_DVI; /* Dual-link LVDS is not supported */
+	}
 }
 
 #endif
@@ -305,8 +303,7 @@ static void __init p1022_ds_setup_arch(void)
 	diu_ops.set_gamma_table		= p1022ds_set_gamma_table;
 	diu_ops.set_monitor_port	= p1022ds_set_monitor_port;
 	diu_ops.set_pixel_clock		= p1022ds_set_pixel_clock;
-	diu_ops.show_monitor_port	= p1022ds_show_monitor_port;
-	diu_ops.set_sysfs_monitor_port	= p1022ds_set_sysfs_monitor_port;
+	diu_ops.valid_monitor_port	= p1022ds_valid_monitor_port;
 #endif
 
 #ifdef CONFIG_SMP

arch/powerpc/platforms/86xx/mpc8610_hpcd.c

@@ -152,10 +152,10 @@ machine_device_initcall(mpc86xx_hpcd, mpc8610_declare_of_platform_devices);
 	(c2 << AD_COMP_2_SHIFT) | (c1 << AD_COMP_1_SHIFT) | \
 	(c0 << AD_COMP_0_SHIFT) | (size << AD_PIXEL_S_SHIFT))
 
-unsigned int mpc8610hpcd_get_pixel_format(unsigned int bits_per_pixel,
-						int monitor_port)
+u32 mpc8610hpcd_get_pixel_format(enum fsl_diu_monitor_port port,
+				 unsigned int bits_per_pixel)
 {
-	static const unsigned long pixelformat[][3] = {
+	static const u32 pixelformat[][3] = {
 		{
 			MAKE_AD(3, 0, 2, 1, 3, 8, 8, 8, 8),
 			MAKE_AD(4, 2, 0, 1, 2, 8, 8, 8, 0),
@@ -170,7 +170,8 @@ unsigned int mpc8610hpcd_get_pixel_format(unsigned int bits_per_pixel,
 	unsigned int arch_monitor;
 
 	/* The DVI port is mis-wired on revision 1 of this board. */
-	arch_monitor = ((*pixis_arch == 0x01) && (monitor_port == 0))? 0 : 1;
+	arch_monitor =
+		((*pixis_arch == 0x01) && (port == FSL_DIU_PORT_DVI)) ? 0 : 1;
 
 	switch (bits_per_pixel) {
 	case 32:
@@ -185,10 +186,11 @@ unsigned int mpc8610hpcd_get_pixel_format(unsigned int bits_per_pixel,
 	}
 }
 
-void mpc8610hpcd_set_gamma_table(int monitor_port, char *gamma_table_base)
+void mpc8610hpcd_set_gamma_table(enum fsl_diu_monitor_port port,
+				 char *gamma_table_base)
 {
 	int i;
-	if (monitor_port == 2) {		/* dual link LVDS */
+	if (port == FSL_DIU_PORT_DLVDS) {
 		for (i = 0; i < 256*3; i++)
 			gamma_table_base[i] = (gamma_table_base[i] << 2) |
 					 ((gamma_table_base[i] >> 6) & 0x03);
@@ -199,17 +201,21 @@ void mpc8610hpcd_set_gamma_table(int monitor_port, char *gamma_table_base)
 #define PX_BRDCFG0_DLINK	(1 << 4)
 #define PX_BRDCFG0_DIU_MASK	(PX_BRDCFG0_DVISEL | PX_BRDCFG0_DLINK)
 
-void mpc8610hpcd_set_monitor_port(int monitor_port)
+void mpc8610hpcd_set_monitor_port(enum fsl_diu_monitor_port port)
 {
-	static const u8 bdcfg[] = {
-		PX_BRDCFG0_DVISEL | PX_BRDCFG0_DLINK,
-		PX_BRDCFG0_DLINK,
-		0,
-	};
-
-	if (monitor_port < 3)
+	switch (port) {
+	case FSL_DIU_PORT_DVI:
 		clrsetbits_8(pixis_bdcfg0, PX_BRDCFG0_DIU_MASK,
-			     bdcfg[monitor_port]);
+			     PX_BRDCFG0_DVISEL | PX_BRDCFG0_DLINK);
+		break;
+	case FSL_DIU_PORT_LVDS:
+		clrsetbits_8(pixis_bdcfg0, PX_BRDCFG0_DIU_MASK,
+			     PX_BRDCFG0_DLINK);
+		break;
+	case FSL_DIU_PORT_DLVDS:
+		clrbits8(pixis_bdcfg0, PX_BRDCFG0_DIU_MASK);
+		break;
+	}
 }
 
 /**
@@ -262,20 +268,10 @@ void mpc8610hpcd_set_pixel_clock(unsigned int pixclock)
 	iounmap(guts);
 }
 
-ssize_t mpc8610hpcd_show_monitor_port(int monitor_port, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE,
-			"%c0 - DVI\n"
-			"%c1 - Single link LVDS\n"
-			"%c2 - Dual link LVDS\n",
-			monitor_port == 0 ? '*' : ' ',
-			monitor_port == 1 ? '*' : ' ',
-			monitor_port == 2 ? '*' : ' ');
-}
-
-int mpc8610hpcd_set_sysfs_monitor_port(int val)
+enum fsl_diu_monitor_port
+mpc8610hpcd_valid_monitor_port(enum fsl_diu_monitor_port port)
 {
-	return val < 3 ? val : 0;
+	return port;
 }
 
 #endif
@@ -307,8 +303,7 @@ static void __init mpc86xx_hpcd_setup_arch(void)
 	diu_ops.set_gamma_table		= mpc8610hpcd_set_gamma_table;
 	diu_ops.set_monitor_port	= mpc8610hpcd_set_monitor_port;
 	diu_ops.set_pixel_clock		= mpc8610hpcd_set_pixel_clock;
-	diu_ops.show_monitor_port	= mpc8610hpcd_show_monitor_port;
-	diu_ops.set_sysfs_monitor_port	= mpc8610hpcd_set_sysfs_monitor_port;
+	diu_ops.valid_monitor_port	= mpc8610hpcd_valid_monitor_port;
 #endif
 
 	pixis_node = of_find_compatible_node(NULL, NULL, "fsl,fpga-pixis");

arch/powerpc/sysdev/fsl_soc.h

@@ -22,15 +22,24 @@ struct device_node;
 extern void fsl_rstcr_restart(char *cmd);
 
 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
+
+/* The different ports that the DIU can be connected to */
+enum fsl_diu_monitor_port {
+	FSL_DIU_PORT_DVI,	/* DVI */
+	FSL_DIU_PORT_LVDS,	/* Single-link LVDS */
+	FSL_DIU_PORT_DLVDS	/* Dual-link LVDS */
+};
+
 struct platform_diu_data_ops {
-	unsigned int (*get_pixel_format) (unsigned int bits_per_pixel,
-		int monitor_port);
-	void (*set_gamma_table) (int monitor_port, char *gamma_table_base);
-	void (*set_monitor_port) (int monitor_port);
-	void (*set_pixel_clock) (unsigned int pixclock);
-	ssize_t (*show_monitor_port) (int monitor_port, char *buf);
-	int (*set_sysfs_monitor_port) (int val);
-	void (*release_bootmem) (void);
+	u32 (*get_pixel_format)(enum fsl_diu_monitor_port port,
+		unsigned int bpp);
+	void (*set_gamma_table)(enum fsl_diu_monitor_port port,
+		char *gamma_table_base);
+	void (*set_monitor_port)(enum fsl_diu_monitor_port port);
+	void (*set_pixel_clock)(unsigned int pixclock);
+	enum fsl_diu_monitor_port (*valid_monitor_port)
+		(enum fsl_diu_monitor_port port);
+	void (*release_bootmem)(void);
 };
 
 extern struct platform_diu_data_ops diu_ops;

drivers/video/Kconfig

@@ -259,6 +259,15 @@ config FB_TILEBLITTING
 comment "Frame buffer hardware drivers"
 	depends on FB
 
+config FB_GRVGA
+	tristate "Aeroflex Gaisler framebuffer support"
+	depends on FB && SPARC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	---help---
+	This enables support for the SVGACTRL framebuffer in the GRLIB IP library from Aeroflex Gaisler.
+
 config FB_CIRRUS
 	tristate "Cirrus Logic support"
 	depends on FB && (ZORRO || PCI)
@@ -1756,9 +1765,10 @@ config FB_AU1100
 config FB_AU1200
 	bool "Au1200 LCD Driver"
 	depends on (FB = y) && MIPS && SOC_AU1200
-	select FB_CFB_FILLRECT
-	select FB_CFB_COPYAREA
-	select FB_CFB_IMAGEBLIT
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
 	help
 	  This is the framebuffer driver for the AMD Au1200 SOC.  It can drive
 	  various panels and CRTs by passing in kernel cmd line option

drivers/video/Makefile

@@ -33,6 +33,7 @@ obj-$(CONFIG_FB_AMIGA)            += amifb.o c2p_planar.o
 obj-$(CONFIG_FB_ARC)              += arcfb.o
 obj-$(CONFIG_FB_CLPS711X)         += clps711xfb.o
 obj-$(CONFIG_FB_CYBER2000)        += cyber2000fb.o
+obj-$(CONFIG_FB_GRVGA)            += grvga.o
 obj-$(CONFIG_FB_PM2)              += pm2fb.o
 obj-$(CONFIG_FB_PM3)		  += pm3fb.o
 

drivers/video/au1200fb.c

@@ -46,14 +46,6 @@
 #include <asm/mach-au1x00/au1000.h>
 #include "au1200fb.h"
 
-#ifdef CONFIG_PM
-#include <asm/mach-au1x00/au1xxx_pm.h>
-#endif
-
-#ifndef CONFIG_FB_AU1200_DEVS
-#define CONFIG_FB_AU1200_DEVS 4
-#endif
-
 #define DRIVER_NAME "au1200fb"
 #define DRIVER_DESC "LCD controller driver for AU1200 processors"
 
@@ -150,7 +142,7 @@ struct au1200_lcd_iodata_t {
 
 /* Private, per-framebuffer management information (independent of the panel itself) */
 struct au1200fb_device {
-	struct fb_info fb_info;			/* FB driver info record */
+	struct fb_info *fb_info;		/* FB driver info record */
 
 	int					plane;
 	unsigned char* 		fb_mem;		/* FrameBuffer memory map */
@@ -158,7 +150,6 @@ struct au1200fb_device {
 	dma_addr_t    		fb_phys;
 };
 
-static struct au1200fb_device _au1200fb_devices[CONFIG_FB_AU1200_DEVS];
 /********************************************************************/
 
 /* LCD controller restrictions */
@@ -171,10 +162,18 @@ static struct au1200fb_device _au1200fb_devices[CONFIG_FB_AU1200_DEVS];
 /* Default number of visible screen buffer to allocate */
 #define AU1200FB_NBR_VIDEO_BUFFERS 1
 
+/* Default maximum number of fb devices to create */
+#define MAX_DEVICE_COUNT	4
+
+/* Default window configuration entry to use (see windows[]) */
+#define DEFAULT_WINDOW_INDEX	2
+
 /********************************************************************/
 
+static struct fb_info *_au1200fb_infos[MAX_DEVICE_COUNT];
 static struct au1200_lcd *lcd = (struct au1200_lcd *) AU1200_LCD_ADDR;
-static int window_index = 2; /* default is zero */
+static int device_count = MAX_DEVICE_COUNT;
+static int window_index = DEFAULT_WINDOW_INDEX;	/* default is zero */
 static int panel_index = 2; /* default is zero */
 static struct window_settings *win;
 static struct panel_settings *panel;
@@ -205,12 +204,6 @@ struct window_settings {
 extern int board_au1200fb_panel_init (void);
 extern int board_au1200fb_panel_shutdown (void);
 
-#ifdef CONFIG_PM
-int au1200fb_pm_callback(au1xxx_power_dev_t *dev,
-		au1xxx_request_t request, void *data);
-au1xxx_power_dev_t *LCD_pm_dev;
-#endif
-
 /*
  * Default window configurations
  */
@@ -652,25 +645,6 @@ static struct panel_settings known_lcd_panels[] =
 
 /********************************************************************/
 
-#ifdef CONFIG_PM
-static int set_brightness(unsigned int brightness)
-{
-	unsigned int hi1, divider;
-
-	/* limit brightness pwm duty to >= 30/1600 */
-	if (brightness < 30) {
-		brightness = 30;
-	}
-	divider = (lcd->pwmdiv & 0x3FFFF) + 1;
-	hi1 = (lcd->pwmhi >> 16) + 1;
-	hi1 = (((brightness & 0xFF) + 1) * divider >> 8);
-	lcd->pwmhi &= 0xFFFF;
-	lcd->pwmhi |= (hi1 << 16);
-
-	return brightness;
-}
-#endif /* CONFIG_PM */
-
 static int winbpp (unsigned int winctrl1)
 {
 	int bits = 0;
@@ -712,8 +686,8 @@ static int fbinfo2index (struct fb_info *fb_info)
 {
 	int i;
 
-	for (i = 0; i < CONFIG_FB_AU1200_DEVS; ++i) {
-		if (fb_info == (struct fb_info *)(&_au1200fb_devices[i].fb_info))
+	for (i = 0; i < device_count; ++i) {
+		if (fb_info == _au1200fb_infos[i])
 			return i;
 	}
 	printk("au1200fb: ERROR: fbinfo2index failed!\n");
@@ -962,7 +936,7 @@ static void au1200_setmode(struct au1200fb_device *fbdev)
 	lcd->window[plane].winctrl2 = ( 0
 		| LCD_WINCTRL2_CKMODE_00
 		| LCD_WINCTRL2_DBM
-		| LCD_WINCTRL2_BX_N( fbdev->fb_info.fix.line_length)
+		| LCD_WINCTRL2_BX_N(fbdev->fb_info->fix.line_length)
 		| LCD_WINCTRL2_SCX_1
 		| LCD_WINCTRL2_SCY_1
 		) ;
@@ -1050,7 +1024,7 @@ static void au1200fb_update_fbinfo(struct fb_info *fbi)
 static int au1200fb_fb_check_var(struct fb_var_screeninfo *var,
 	struct fb_info *fbi)
 {
-	struct au1200fb_device *fbdev = (struct au1200fb_device *)fbi;
+	struct au1200fb_device *fbdev = fbi->par;
 	u32 pixclock;
 	int screen_size, plane;
 
@@ -1142,7 +1116,7 @@ static int au1200fb_fb_check_var(struct fb_var_screeninfo *var,
  */
 static int au1200fb_fb_set_par(struct fb_info *fbi)
 {
-	struct au1200fb_device *fbdev = (struct au1200fb_device *)fbi;
+	struct au1200fb_device *fbdev = fbi->par;
 
 	au1200fb_update_fbinfo(fbi);
 	au1200_setmode(fbdev);
@@ -1246,11 +1220,7 @@ static int au1200fb_fb_mmap(struct fb_info *info, struct vm_area_struct *vma)
 {
 	unsigned int len;
 	unsigned long start=0, off;
-	struct au1200fb_device *fbdev = (struct au1200fb_device *) info;
-
-#ifdef CONFIG_PM
-	au1xxx_pm_access(LCD_pm_dev);
-#endif
+	struct au1200fb_device *fbdev = info->par;
 
 	if (vma->vm_pgoff > (~0UL >> PAGE_SHIFT)) {
 		return -EINVAL;
@@ -1461,10 +1431,6 @@ static int au1200fb_ioctl(struct fb_info *info, unsigned int cmd,
 	int plane;
 	int val;
 
-#ifdef CONFIG_PM
-	au1xxx_pm_access(LCD_pm_dev);
-#endif
-
 	plane = fbinfo2index(info);
 	print_dbg("au1200fb: ioctl %d on plane %d\n", cmd, plane);
 
@@ -1536,9 +1502,11 @@ static struct fb_ops au1200fb_fb_ops = {
 	.fb_set_par	= au1200fb_fb_set_par,
 	.fb_setcolreg	= au1200fb_fb_setcolreg,
 	.fb_blank	= au1200fb_fb_blank,
-	.fb_fillrect	= cfb_fillrect,
-	.fb_copyarea	= cfb_copyarea,
-	.fb_imageblit	= cfb_imageblit,
+	.fb_fillrect	= sys_fillrect,
+	.fb_copyarea	= sys_copyarea,
+	.fb_imageblit	= sys_imageblit,
+	.fb_read	= fb_sys_read,
+	.fb_write	= fb_sys_write,
 	.fb_sync	= NULL,
 	.fb_ioctl	= au1200fb_ioctl,
 	.fb_mmap	= au1200fb_fb_mmap,
@@ -1561,10 +1529,9 @@ static irqreturn_t au1200fb_handle_irq(int irq, void* dev_id)
 
 static int au1200fb_init_fbinfo(struct au1200fb_device *fbdev)
 {
-	struct fb_info *fbi = &fbdev->fb_info;
+	struct fb_info *fbi = fbdev->fb_info;
 	int bpp;
 
-	memset(fbi, 0, sizeof(struct fb_info));
 	fbi->fbops = &au1200fb_fb_ops;
 
 	bpp = winbpp(win->w[fbdev->plane].mode_winctrl1);
@@ -1623,24 +1590,36 @@ static int au1200fb_init_fbinfo(struct au1200fb_device *fbdev)
 
 /* AU1200 LCD controller device driver */
 
-static int au1200fb_drv_probe(struct platform_device *dev)
+static int __devinit au1200fb_drv_probe(struct platform_device *dev)
 {
 	struct au1200fb_device *fbdev;
+	struct fb_info *fbi = NULL;
 	unsigned long page;
-	int bpp, plane, ret;
+	int bpp, plane, ret, irq;
 
-	if (!dev)
-		return -EINVAL;
+	/* shut gcc up */
+	ret = 0;
+	fbdev = NULL;
+
+	/* Kickstart the panel */
+	au1200_setpanel(panel);
 
-	for (plane = 0; plane < CONFIG_FB_AU1200_DEVS; ++plane) {
+	for (plane = 0; plane < device_count; ++plane) {
 		bpp = winbpp(win->w[plane].mode_winctrl1);
 		if (win->w[plane].xres == 0)
 			win->w[plane].xres = panel->Xres;
 		if (win->w[plane].yres == 0)
 			win->w[plane].yres = panel->Yres;
 
-		fbdev = &_au1200fb_devices[plane];
-		memset(fbdev, 0, sizeof(struct au1200fb_device));
+		fbi = framebuffer_alloc(sizeof(struct au1200fb_device),
+					&dev->dev);
+		if (!fbi)
+			goto failed;
+
+		_au1200fb_infos[plane] = fbi;
+		fbdev = fbi->par;
+		fbdev->fb_info = fbi;
+
 		fbdev->plane = plane;
 
 		/* Allocate the framebuffer to the maximum screen size */
@@ -1673,30 +1652,31 @@ static int au1200fb_drv_probe(struct platform_device *dev)
 			goto failed;
 
 		/* Register new framebuffer */
-		if ((ret = register_framebuffer(&fbdev->fb_info)) < 0) {
+		ret = register_framebuffer(fbi);
+		if (ret < 0) {
 			print_err("cannot register new framebuffer");
 			goto failed;
 		}
 
-		au1200fb_fb_set_par(&fbdev->fb_info);
+		au1200fb_fb_set_par(fbi);
 
 #if !defined(CONFIG_FRAMEBUFFER_CONSOLE) && defined(CONFIG_LOGO)
 		if (plane == 0)
-			if (fb_prepare_logo(&fbdev->fb_info, FB_ROTATE_UR)) {
+			if (fb_prepare_logo(fbi, FB_ROTATE_UR)) {
 				/* Start display and show logo on boot */
-				fb_set_cmap(&fbdev->fb_info.cmap,
-						&fbdev->fb_info);
-
-				fb_show_logo(&fbdev->fb_info, FB_ROTATE_UR);
+				fb_set_cmap(&fbi->cmap, fbi);
+				fb_show_logo(fbi, FB_ROTATE_UR);
 			}
 #endif
 	}
 
 	/* Now hook interrupt too */
-	if ((ret = request_irq(AU1200_LCD_INT, au1200fb_handle_irq,
-		 	  IRQF_DISABLED | IRQF_SHARED, "lcd", (void *)dev)) < 0) {
+	irq = platform_get_irq(dev, 0);
+	ret = request_irq(irq, au1200fb_handle_irq,
+			  IRQF_DISABLED | IRQF_SHARED, "lcd", (void *)dev);
+	if (ret) {
 		print_err("fail to request interrupt line %d (err: %d)",
-			  AU1200_LCD_INT, ret);
+			  irq, ret);
 		goto failed;
 	}
 
@@ -1705,84 +1685,108 @@ static int au1200fb_drv_probe(struct platform_device *dev)
 failed:
 	/* NOTE: This only does the current plane/window that failed; others are still active */
 	if (fbdev->fb_mem)
-		dma_free_noncoherent(dev, PAGE_ALIGN(fbdev->fb_len),
+		dma_free_noncoherent(&dev->dev, PAGE_ALIGN(fbdev->fb_len),
 				fbdev->fb_mem, fbdev->fb_phys);
-	if (fbdev->fb_info.cmap.len != 0)
-		fb_dealloc_cmap(&fbdev->fb_info.cmap);
-	if (fbdev->fb_info.pseudo_palette)
-		kfree(fbdev->fb_info.pseudo_palette);
+	if (fbi) {
+		if (fbi->cmap.len != 0)
+			fb_dealloc_cmap(&fbi->cmap);
+		kfree(fbi->pseudo_palette);
+	}
 	if (plane == 0)
 		free_irq(AU1200_LCD_INT, (void*)dev);
 	return ret;
 }
 
-static int au1200fb_drv_remove(struct platform_device *dev)
+static int __devexit au1200fb_drv_remove(struct platform_device *dev)
 {
 	struct au1200fb_device *fbdev;
+	struct fb_info *fbi;
 	int plane;
 
-	if (!dev)
-		return -ENODEV;
-
 	/* Turn off the panel */
 	au1200_setpanel(NULL);
 
-	for (plane = 0; plane < CONFIG_FB_AU1200_DEVS; ++plane)
-	{
-		fbdev = &_au1200fb_devices[plane];
+	for (plane = 0; plane < device_count; ++plane)	{
+		fbi = _au1200fb_infos[plane];
+		fbdev = fbi->par;
 
 		/* Clean up all probe data */
-		unregister_framebuffer(&fbdev->fb_info);
+		unregister_framebuffer(fbi);
 		if (fbdev->fb_mem)
 			dma_free_noncoherent(&dev->dev,
 					PAGE_ALIGN(fbdev->fb_len),
 					fbdev->fb_mem, fbdev->fb_phys);
-		if (fbdev->fb_info.cmap.len != 0)
-			fb_dealloc_cmap(&fbdev->fb_info.cmap);
-		if (fbdev->fb_info.pseudo_palette)
-			kfree(fbdev->fb_info.pseudo_palette);
+		if (fbi->cmap.len != 0)
+			fb_dealloc_cmap(&fbi->cmap);
+		kfree(fbi->pseudo_palette);
+
+		framebuffer_release(fbi);
+		_au1200fb_infos[plane] = NULL;
 	}
 
-	free_irq(AU1200_LCD_INT, (void *)dev);
+	free_irq(platform_get_irq(dev, 0), (void *)dev);
 
 	return 0;
 }
 
 #ifdef CONFIG_PM
-static int au1200fb_drv_suspend(struct platform_device *dev, u32 state)
+static int au1200fb_drv_suspend(struct device *dev)
 {
-	/* TODO */
+	au1200_setpanel(NULL);
+
+	lcd->outmask = 0;
+	au_sync();
+
 	return 0;
 }
 
-static int au1200fb_drv_resume(struct platform_device *dev)
+static int au1200fb_drv_resume(struct device *dev)
 {
-	/* TODO */
+	struct fb_info *fbi;
+	int i;
+
+	/* Kickstart the panel */
+	au1200_setpanel(panel);
+
+	for (i = 0; i < device_count; i++) {
+		fbi = _au1200fb_infos[i];
+		au1200fb_fb_set_par(fbi);
+	}
+
 	return 0;
 }
+
+static const struct dev_pm_ops au1200fb_pmops = {
+	.suspend	= au1200fb_drv_suspend,
+	.resume		= au1200fb_drv_resume,
+	.freeze		= au1200fb_drv_suspend,
+	.thaw		= au1200fb_drv_resume,
+};
+
+#define AU1200FB_PMOPS	(&au1200fb_pmops)
+
+#else
+#define AU1200FB_PMOPS	NULL
 #endif /* CONFIG_PM */
 
 static struct platform_driver au1200fb_driver = {
 	.driver = {
-		.name		= "au1200-lcd",
-		.owner          = THIS_MODULE,
+		.name	= "au1200-lcd",
+		.owner	= THIS_MODULE,
+		.pm	= AU1200FB_PMOPS,
 	},
 	.probe		= au1200fb_drv_probe,
-	.remove		= au1200fb_drv_remove,
-#ifdef CONFIG_PM
-	.suspend	= au1200fb_drv_suspend,
-	.resume		= au1200fb_drv_resume,
-#endif
+	.remove		= __devexit_p(au1200fb_drv_remove),
 };
 
 /*-------------------------------------------------------------------------*/
 
 /* Kernel driver */
 
-static void au1200fb_setup(void)
+static int au1200fb_setup(void)
 {
-	char* options = NULL;
-	char* this_opt;
+	char *options = NULL;
+	char *this_opt, *endptr;
 	int num_panels = ARRAY_SIZE(known_lcd_panels);
 	int panel_idx = -1;
 
@@ -1827,70 +1831,42 @@ static void au1200fb_setup(void)
 				nohwcursor = 1;
 			}
 
-			/* Unsupported option */
-			else {
-				print_warn("Unsupported option \"%s\"", this_opt);
+			else if (strncmp(this_opt, "devices:", 8) == 0) {
+				this_opt += 8;
+				device_count = simple_strtol(this_opt,
+							     &endptr, 0);
+				if ((device_count < 0) ||
+				    (device_count > MAX_DEVICE_COUNT))
+					device_count = MAX_DEVICE_COUNT;
 			}
-		}
-	}
-}
 
-#ifdef CONFIG_PM
-static int au1200fb_pm_callback(au1xxx_power_dev_t *dev,
-		au1xxx_request_t request, void *data) {
-	int retval = -1;
-	unsigned int d = 0;
-	unsigned int brightness = 0;
-
-	if (request == AU1XXX_PM_SLEEP) {
-		board_au1200fb_panel_shutdown();
-	}
-	else if (request == AU1XXX_PM_WAKEUP) {
-		if(dev->prev_state == SLEEP_STATE)
-		{
-			int plane;
-			au1200_setpanel(panel);
-			for (plane = 0; plane < CONFIG_FB_AU1200_DEVS; ++plane) 	{
-				struct au1200fb_device *fbdev;
-				fbdev = &_au1200fb_devices[plane];
-				au1200fb_fb_set_par(&fbdev->fb_info);
+			else if (strncmp(this_opt, "wincfg:", 7) == 0) {
+				this_opt += 7;
+				window_index = simple_strtol(this_opt,
+							     &endptr, 0);
+				if ((window_index < 0) ||
+				    (window_index >= ARRAY_SIZE(windows)))
+					window_index = DEFAULT_WINDOW_INDEX;
 			}
-		}
 
-		d = *((unsigned int*)data);
-		if(d <=10) brightness = 26;
-		else if(d<=20) brightness = 51;
-		else if(d<=30) brightness = 77;
-		else if(d<=40) brightness = 102;
-		else if(d<=50) brightness = 128;
-		else if(d<=60) brightness = 153;
-		else if(d<=70) brightness = 179;
-		else if(d<=80) brightness = 204;
-		else if(d<=90) brightness = 230;
-		else brightness = 255;
-		set_brightness(brightness);
-	} else if (request == AU1XXX_PM_GETSTATUS) {
-		return dev->cur_state;
-	} else if (request == AU1XXX_PM_ACCESS) {
-		if (dev->cur_state != SLEEP_STATE)
-			return retval;
-		else {
-			au1200_setpanel(panel);
+			else if (strncmp(this_opt, "off", 3) == 0)
+				return 1;
+			/* Unsupported option */
+			else {
+				print_warn("Unsupported option \"%s\"", this_opt);
+			}
 		}
-	} else if (request == AU1XXX_PM_IDLE) {
-	} else if (request == AU1XXX_PM_CLEANUP) {
 	}
-
-	return retval;
+	return 0;
 }
-#endif
 
 static int __init au1200fb_init(void)
 {
 	print_info("" DRIVER_DESC "");
 
 	/* Setup driver with options */
-	au1200fb_setup();
+	if (au1200fb_setup())
+		return -ENODEV;
 
 	/* Point to the panel selected */
 	panel = &known_lcd_panels[panel_index];
@@ -1899,17 +1875,6 @@ static int __init au1200fb_init(void)
 	printk(DRIVER_NAME ": Panel %d %s\n", panel_index, panel->name);
 	printk(DRIVER_NAME ": Win %d %s\n", window_index, win->name);
 
-	/* Kickstart the panel, the framebuffers/windows come soon enough */
-	au1200_setpanel(panel);
-
-	#ifdef CONFIG_PM
-	LCD_pm_dev = new_au1xxx_power_device("LCD", &au1200fb_pm_callback, NULL);
-	if ( LCD_pm_dev == NULL)
-		printk(KERN_INFO "Unable to create a power management device entry for the au1200fb.\n");
-	else
-		printk(KERN_INFO "Power management device entry for the au1200fb loaded.\n");
-	#endif
-
 	return platform_driver_register(&au1200fb_driver);
 }
 

drivers/video/backlight/adp8860_bl.c

@@ -7,7 +7,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/version.h>
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/pm.h>

drivers/video/backlight/adp8870_bl.c

@@ -7,7 +7,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/version.h>
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/pm.h>

drivers/video/carminefb.c

@@ -32,11 +32,11 @@
 #define CARMINEFB_DEFAULT_VIDEO_MODE	1
 
 static unsigned int fb_mode = CARMINEFB_DEFAULT_VIDEO_MODE;
-module_param(fb_mode, uint, 444);
+module_param(fb_mode, uint, 0444);
 MODULE_PARM_DESC(fb_mode, "Initial video mode as integer.");
 
 static char *fb_mode_str;
-module_param(fb_mode_str, charp, 444);
+module_param(fb_mode_str, charp, 0444);
 MODULE_PARM_DESC(fb_mode_str, "Initial video mode in characters.");
 
 /*
@@ -46,7 +46,7 @@ MODULE_PARM_DESC(fb_mode_str, "Initial video mode in characters.");
  * 0b010 Display 1
  */
 static int fb_displays = CARMINE_USE_DISPLAY0 | CARMINE_USE_DISPLAY1;
-module_param(fb_displays, int, 444);
+module_param(fb_displays, int, 0444);
 MODULE_PARM_DESC(fb_displays, "Bit mode, which displays are used");
 
 struct carmine_hw {

drivers/video/controlfb.c

@@ -550,7 +550,7 @@ static void control_set_hardware(struct fb_info_control *p, struct fb_par_contro
 
 
 /*
- * Parse user speficied options (`video=controlfb:')
+ * Parse user specified options (`video=controlfb:')
  */
 static void __init control_setup(char *options)
 {

drivers/video/da8xx-fb.c

@@ -35,6 +35,9 @@
 
 #define DRIVER_NAME "da8xx_lcdc"
 
+#define LCD_VERSION_1	1
+#define LCD_VERSION_2	2
+
 /* LCD Status Register */
 #define LCD_END_OF_FRAME1		BIT(9)
 #define LCD_END_OF_FRAME0		BIT(8)
@@ -49,7 +52,9 @@
 #define LCD_DMA_BURST_4			0x2
 #define LCD_DMA_BURST_8			0x3
 #define LCD_DMA_BURST_16		0x4
-#define LCD_END_OF_FRAME_INT_ENA	BIT(2)
+#define LCD_V1_END_OF_FRAME_INT_ENA	BIT(2)
+#define LCD_V2_END_OF_FRAME0_INT_ENA	BIT(8)
+#define LCD_V2_END_OF_FRAME1_INT_ENA	BIT(9)
 #define LCD_DUAL_FRAME_BUFFER_ENABLE	BIT(0)
 
 /* LCD Control Register */
@@ -65,12 +70,18 @@
 #define LCD_MONO_8BIT_MODE		BIT(9)
 #define LCD_RASTER_ORDER		BIT(8)
 #define LCD_TFT_MODE			BIT(7)
-#define LCD_UNDERFLOW_INT_ENA		BIT(6)
-#define LCD_PL_ENABLE			BIT(4)
+#define LCD_V1_UNDERFLOW_INT_ENA	BIT(6)
+#define LCD_V2_UNDERFLOW_INT_ENA	BIT(5)
+#define LCD_V1_PL_INT_ENA		BIT(4)
+#define LCD_V2_PL_INT_ENA		BIT(6)
 #define LCD_MONOCHROME_MODE		BIT(1)
 #define LCD_RASTER_ENABLE		BIT(0)
 #define LCD_TFT_ALT_ENABLE		BIT(23)
 #define LCD_STN_565_ENABLE		BIT(24)
+#define LCD_V2_DMA_CLK_EN		BIT(2)
+#define LCD_V2_LIDD_CLK_EN		BIT(1)
+#define LCD_V2_CORE_CLK_EN		BIT(0)
+#define LCD_V2_LPP_B10			26
 
 /* LCD Raster Timing 2 Register */
 #define LCD_AC_BIAS_TRANSITIONS_PER_INT(x)	((x) << 16)
@@ -82,6 +93,7 @@
 #define LCD_INVERT_FRAME_CLOCK			BIT(20)
 
 /* LCD Block */
+#define  LCD_PID_REG				0x0
 #define  LCD_CTRL_REG				0x4
 #define  LCD_STAT_REG				0x8
 #define  LCD_RASTER_CTRL_REG			0x28
@@ -94,6 +106,17 @@
 #define  LCD_DMA_FRM_BUF_BASE_ADDR_1_REG	0x4C
 #define  LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG	0x50
 
+/* Interrupt Registers available only in Version 2 */
+#define  LCD_RAW_STAT_REG			0x58
+#define  LCD_MASKED_STAT_REG			0x5c
+#define  LCD_INT_ENABLE_SET_REG			0x60
+#define  LCD_INT_ENABLE_CLR_REG			0x64
+#define  LCD_END_OF_INT_IND_REG			0x68
+
+/* Clock registers available only on Version 2 */
+#define  LCD_CLK_ENABLE_REG			0x6c
+#define  LCD_CLK_RESET_REG			0x70
+
 #define LCD_NUM_BUFFERS	2
 
 #define WSI_TIMEOUT	50
@@ -105,6 +128,8 @@
 
 static resource_size_t da8xx_fb_reg_base;
 static struct resource *lcdc_regs;
+static unsigned int lcd_revision;
+static irq_handler_t lcdc_irq_handler;
 
 static inline unsigned int lcdc_read(unsigned int addr)
 {
@@ -240,6 +265,7 @@ static void lcd_blit(int load_mode, struct da8xx_fb_par *par)
 	u32 end;
 	u32 reg_ras;
 	u32 reg_dma;
+	u32 reg_int;
 
 	/* init reg to clear PLM (loading mode) fields */
 	reg_ras = lcdc_read(LCD_RASTER_CTRL_REG);
@@ -252,7 +278,14 @@ static void lcd_blit(int load_mode, struct da8xx_fb_par *par)
 		end      = par->dma_end;
 
 		reg_ras |= LCD_PALETTE_LOAD_MODE(DATA_ONLY);
-		reg_dma |= LCD_END_OF_FRAME_INT_ENA;
+		if (lcd_revision == LCD_VERSION_1) {
+			reg_dma |= LCD_V1_END_OF_FRAME_INT_ENA;
+		} else {
+			reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) |
+				LCD_V2_END_OF_FRAME0_INT_ENA |
+				LCD_V2_END_OF_FRAME1_INT_ENA;
+			lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG);
+		}
 		reg_dma |= LCD_DUAL_FRAME_BUFFER_ENABLE;
 
 		lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
@@ -264,7 +297,14 @@ static void lcd_blit(int load_mode, struct da8xx_fb_par *par)
 		end      = start + par->palette_sz - 1;
 
 		reg_ras |= LCD_PALETTE_LOAD_MODE(PALETTE_ONLY);
-		reg_ras |= LCD_PL_ENABLE;
+
+		if (lcd_revision == LCD_VERSION_1) {
+			reg_ras |= LCD_V1_PL_INT_ENA;
+		} else {
+			reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) |
+				LCD_V2_PL_INT_ENA;
+			lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG);
+		}
 
 		lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
 		lcdc_write(end, LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
@@ -348,6 +388,7 @@ static void lcd_cfg_vertical_sync(int back_porch, int pulse_width,
 static int lcd_cfg_display(const struct lcd_ctrl_config *cfg)
 {
 	u32 reg;
+	u32 reg_int;
 
 	reg = lcdc_read(LCD_RASTER_CTRL_REG) & ~(LCD_TFT_MODE |
 						LCD_MONO_8BIT_MODE |
@@ -375,7 +416,13 @@ static int lcd_cfg_display(const struct lcd_ctrl_config *cfg)
 	}
 
 	/* enable additional interrupts here */
-	reg |= LCD_UNDERFLOW_INT_ENA;
+	if (lcd_revision == LCD_VERSION_1) {
+		reg |= LCD_V1_UNDERFLOW_INT_ENA;
+	} else {
+		reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) |
+			LCD_V2_UNDERFLOW_INT_ENA;
+		lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG);
+	}
 
 	lcdc_write(reg, LCD_RASTER_CTRL_REG);
 
@@ -511,6 +558,9 @@ static void lcd_reset(struct da8xx_fb_par *par)
 	/* DMA has to be disabled */
 	lcdc_write(0, LCD_DMA_CTRL_REG);
 	lcdc_write(0, LCD_RASTER_CTRL_REG);
+
+	if (lcd_revision == LCD_VERSION_2)
+		lcdc_write(0, LCD_INT_ENABLE_SET_REG);
 }
 
 static void lcd_calc_clk_divider(struct da8xx_fb_par *par)
@@ -523,6 +573,11 @@ static void lcd_calc_clk_divider(struct da8xx_fb_par *par)
 	/* Configure the LCD clock divisor. */
 	lcdc_write(LCD_CLK_DIVISOR(div) |
 			(LCD_RASTER_MODE & 0x1), LCD_CTRL_REG);
+
+	if (lcd_revision == LCD_VERSION_2)
+		lcdc_write(LCD_V2_DMA_CLK_EN | LCD_V2_LIDD_CLK_EN |
+				LCD_V2_CORE_CLK_EN, LCD_CLK_ENABLE_REG);
+
 }
 
 static int lcd_init(struct da8xx_fb_par *par, const struct lcd_ctrl_config *cfg,
@@ -583,7 +638,63 @@ static int lcd_init(struct da8xx_fb_par *par, const struct lcd_ctrl_config *cfg,
 	return 0;
 }
 
-static irqreturn_t lcdc_irq_handler(int irq, void *arg)
+/* IRQ handler for version 2 of LCDC */
+static irqreturn_t lcdc_irq_handler_rev02(int irq, void *arg)
+{
+	struct da8xx_fb_par *par = arg;
+	u32 stat = lcdc_read(LCD_MASKED_STAT_REG);
+	u32 reg_int;
+
+	if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) {
+		lcd_disable_raster();
+		lcdc_write(stat, LCD_MASKED_STAT_REG);
+		lcd_enable_raster();
+	} else if (stat & LCD_PL_LOAD_DONE) {
+		/*
+		 * Must disable raster before changing state of any control bit.
+		 * And also must be disabled before clearing the PL loading
+		 * interrupt via the following write to the status register. If
+		 * this is done after then one gets multiple PL done interrupts.
+		 */
+		lcd_disable_raster();
+
+		lcdc_write(stat, LCD_MASKED_STAT_REG);
+
+		/* Disable PL completion inerrupt */
+		reg_int = lcdc_read(LCD_INT_ENABLE_CLR_REG) |
+		       (LCD_V2_PL_INT_ENA);
+		lcdc_write(reg_int, LCD_INT_ENABLE_CLR_REG);
+
+		/* Setup and start data loading mode */
+		lcd_blit(LOAD_DATA, par);
+	} else {
+		lcdc_write(stat, LCD_MASKED_STAT_REG);
+
+		if (stat & LCD_END_OF_FRAME0) {
+			lcdc_write(par->dma_start,
+				   LCD_DMA_FRM_BUF_BASE_ADDR_0_REG);
+			lcdc_write(par->dma_end,
+				   LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG);
+			par->vsync_flag = 1;
+			wake_up_interruptible(&par->vsync_wait);
+		}
+
+		if (stat & LCD_END_OF_FRAME1) {
+			lcdc_write(par->dma_start,
+				   LCD_DMA_FRM_BUF_BASE_ADDR_1_REG);
+			lcdc_write(par->dma_end,
+				   LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG);
+			par->vsync_flag = 1;
+			wake_up_interruptible(&par->vsync_wait);
+		}
+	}
+
+	lcdc_write(0, LCD_END_OF_INT_IND_REG);
+	return IRQ_HANDLED;
+}
+
+/* IRQ handler for version 1 LCDC */
+static irqreturn_t lcdc_irq_handler_rev01(int irq, void *arg)
 {
 	struct da8xx_fb_par *par = arg;
 	u32 stat = lcdc_read(LCD_STAT_REG);
@@ -606,7 +717,7 @@ static irqreturn_t lcdc_irq_handler(int irq, void *arg)
 
 		/* Disable PL completion inerrupt */
 		reg_ras  = lcdc_read(LCD_RASTER_CTRL_REG);
-		reg_ras &= ~LCD_PL_ENABLE;
+		reg_ras &= ~LCD_V1_PL_INT_ENA;
 		lcdc_write(reg_ras, LCD_RASTER_CTRL_REG);
 
 		/* Setup and start data loading mode */
@@ -945,6 +1056,22 @@ static int __devinit fb_probe(struct platform_device *device)
 	if (ret)
 		goto err_clk_put;
 
+	/* Determine LCD IP Version */
+	switch (lcdc_read(LCD_PID_REG)) {
+	case 0x4C100102:
+		lcd_revision = LCD_VERSION_1;
+		break;
+	case 0x4F200800:
+		lcd_revision = LCD_VERSION_2;
+		break;
+	default:
+		dev_warn(&device->dev, "Unknown PID Reg value 0x%x, "
+				"defaulting to LCD revision 1\n",
+				lcdc_read(LCD_PID_REG));
+		lcd_revision = LCD_VERSION_1;
+		break;
+	}
+
 	for (i = 0, lcdc_info = known_lcd_panels;
 		i < ARRAY_SIZE(known_lcd_panels);
 		i++, lcdc_info++) {
@@ -1085,7 +1212,13 @@ static int __devinit fb_probe(struct platform_device *device)
 	}
 #endif
 
-	ret = request_irq(par->irq, lcdc_irq_handler, 0, DRIVER_NAME, par);
+	if (lcd_revision == LCD_VERSION_1)
+		lcdc_irq_handler = lcdc_irq_handler_rev01;
+	else
+		lcdc_irq_handler = lcdc_irq_handler_rev02;
+
+	ret = request_irq(par->irq, lcdc_irq_handler, 0,
+			DRIVER_NAME, par);
 	if (ret)
 		goto irq_freq;
 	return 0;

drivers/video/fb_defio.c

@@ -223,8 +223,7 @@ void fb_deferred_io_cleanup(struct fb_info *info)
 	int i;
 
 	BUG_ON(!fbdefio);
-	cancel_delayed_work(&info->deferred_work);
-	flush_scheduled_work();
+	cancel_delayed_work_sync(&info->deferred_work);
 
 	/* clear out the mapping that we setup */
 	for (i = 0 ; i < info->fix.smem_len; i += PAGE_SIZE) {

drivers/video/fsl-diu-fb.c

@@ -31,8 +31,6 @@
 #include <linux/uaccess.h>
 #include <linux/vmalloc.h>
 
-#include <linux/of_platform.h>
-
 #include <sysdev/fsl_soc.h>
 #include <linux/fsl-diu-fb.h>
 #include "edid.h"
@@ -183,7 +181,8 @@ static struct fb_videomode __devinitdata fsl_diu_mode_db[] = {
 
 static char *fb_mode = "1024x768-32@60";
 static unsigned long default_bpp = 32;
-static int monitor_port;
+static enum fsl_diu_monitor_port monitor_port;
+static char *monitor_string;
 
 #if defined(CONFIG_NOT_COHERENT_CACHE)
 static u8 *coherence_data;
@@ -201,7 +200,7 @@ struct fsl_diu_data {
 	void *dummy_aoi_virt;
 	unsigned int irq;
 	int fb_enabled;
-	int monitor_port;
+	enum fsl_diu_monitor_port monitor_port;
 };
 
 struct mfb_info {
@@ -281,6 +280,37 @@ static struct diu_hw dr = {
 
 static struct diu_pool pool;
 
+/**
+ * fsl_diu_name_to_port - convert a port name to a monitor port enum
+ *
+ * Takes the name of a monitor port ("dvi", "lvds", or "dlvds") and returns
+ * the enum fsl_diu_monitor_port that corresponds to that string.
+ *
+ * For compatibility with older versions, a number ("0", "1", or "2") is also
+ * supported.
+ *
+ * If the string is unknown, DVI is assumed.
+ *
+ * If the particular port is not supported by the platform, another port
+ * (platform-specific) is chosen instead.
+ */
+static enum fsl_diu_monitor_port fsl_diu_name_to_port(const char *s)
+{
+	enum fsl_diu_monitor_port port = FSL_DIU_PORT_DVI;
+	unsigned long val;
+
+	if (s) {
+		if (!strict_strtoul(s, 10, &val) && (val <= 2))
+			port = (enum fsl_diu_monitor_port) val;
+		else if (strncmp(s, "lvds", 4) == 0)
+			port = FSL_DIU_PORT_LVDS;
+		else if (strncmp(s, "dlvds", 5) == 0)
+			port = FSL_DIU_PORT_DLVDS;
+	}
+
+	return diu_ops.valid_monitor_port(port);
+}
+
 /**
  * fsl_diu_alloc - allocate memory for the DIU
  * @size: number of bytes to allocate
@@ -831,9 +861,8 @@ static int fsl_diu_set_par(struct fb_info *info)
 		}
 	}
 
-	ad->pix_fmt =
-		diu_ops.get_pixel_format(var->bits_per_pixel,
-					 machine_data->monitor_port);
+	ad->pix_fmt = diu_ops.get_pixel_format(machine_data->monitor_port,
+					       var->bits_per_pixel);
 	ad->addr    = cpu_to_le32(info->fix.smem_start);
 	ad->src_size_g_alpha = cpu_to_le32((var->yres_virtual << 12) |
 				var->xres_virtual) | mfbi->g_alpha;
@@ -1439,16 +1468,12 @@ static void free_buf(struct device *dev, struct diu_addr *buf, u32 size,
 static ssize_t store_monitor(struct device *device,
 	struct device_attribute *attr, const char *buf, size_t count)
 {
-	int old_monitor_port;
-	unsigned long val;
+	enum fsl_diu_monitor_port old_monitor_port;
 	struct fsl_diu_data *machine_data =
 		container_of(attr, struct fsl_diu_data, dev_attr);
 
-	if (strict_strtoul(buf, 10, &val))
-		return 0;
-
 	old_monitor_port = machine_data->monitor_port;
-	machine_data->monitor_port = diu_ops.set_sysfs_monitor_port(val);
+	machine_data->monitor_port = fsl_diu_name_to_port(buf);
 
 	if (old_monitor_port != machine_data->monitor_port) {
 		/* All AOIs need adjust pixel format
@@ -1468,7 +1493,17 @@ static ssize_t show_monitor(struct device *device,
 {
 	struct fsl_diu_data *machine_data =
 		container_of(attr, struct fsl_diu_data, dev_attr);
-	return diu_ops.show_monitor_port(machine_data->monitor_port, buf);
+
+	switch (machine_data->monitor_port) {
+	case FSL_DIU_PORT_DVI:
+		return sprintf(buf, "DVI\n");
+	case FSL_DIU_PORT_LVDS:
+		return sprintf(buf, "Single-link LVDS\n");
+	case FSL_DIU_PORT_DLVDS:
+		return sprintf(buf, "Dual-link LVDS\n");
+	}
+
+	return 0;
 }
 
 static int __devinit fsl_diu_probe(struct platform_device *ofdev)
@@ -1692,8 +1727,7 @@ static int __init fsl_diu_setup(char *options)
 		if (!*opt)
 			continue;
 		if (!strncmp(opt, "monitor=", 8)) {
-			if (!strict_strtoul(opt + 8, 10, &val) && (val <= 2))
-				monitor_port = val;
+			monitor_port = fsl_diu_name_to_port(opt + 8);
 		} else if (!strncmp(opt, "bpp=", 4)) {
 			if (!strict_strtoul(opt + 4, 10, &val))
 				default_bpp = val;
@@ -1746,6 +1780,8 @@ static int __init fsl_diu_init(void)
 	if (fb_get_options("fslfb", &option))
 		return -ENODEV;
 	fsl_diu_setup(option);
+#else
+	monitor_port = fsl_diu_name_to_port(monitor_string);
 #endif
 	printk(KERN_INFO "Freescale DIU driver\n");
 
@@ -1812,7 +1848,7 @@ MODULE_PARM_DESC(mode,
 	"Specify resolution as \"<xres>x<yres>[-<bpp>][@<refresh>]\" ");
 module_param_named(bpp, default_bpp, ulong, 0);
 MODULE_PARM_DESC(bpp, "Specify bit-per-pixel if not specified mode");
-module_param_named(monitor, monitor_port, int, 0);
-MODULE_PARM_DESC(monitor,
-	"Specify the monitor port (0, 1 or 2) if supported by the platform");
+module_param_named(monitor, monitor_string, charp, 0);
+MODULE_PARM_DESC(monitor, "Specify the monitor port "
+	"(\"dvi\", \"lvds\", or \"dlvds\") if supported by the platform");
 

drivers/video/grvga.c

@@ -0,0 +1,579 @@
+/*
+ * Driver for Aeroflex Gaisler SVGACTRL framebuffer device.
+ *
+ * 2011 (c) Aeroflex Gaisler AB
+ *
+ * Full documentation of the core can be found here:
+ * http://www.gaisler.com/products/grlib/grip.pdf
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * Contributors: Kristoffer Glembo <kristoffer@gaisler.com>
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/of_platform.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/mm.h>
+#include <linux/fb.h>
+#include <linux/io.h>
+
+struct grvga_regs {
+	u32 status; 		/* 0x00 */
+	u32 video_length; 	/* 0x04 */
+	u32 front_porch;	/* 0x08 */
+	u32 sync_length;	/* 0x0C */
+	u32 line_length;	/* 0x10 */
+	u32 fb_pos;		/* 0x14 */
+	u32 clk_vector[4];	/* 0x18 */
+	u32 clut;	        /* 0x20 */
+};
+
+struct grvga_par {
+	struct grvga_regs *regs;
+	u32 color_palette[16];  /* 16 entry pseudo palette used by fbcon in true color mode */
+	int clk_sel;
+	int fb_alloced;         /* = 1 if framebuffer is allocated in main memory */
+};
+
+
+static const struct fb_videomode grvga_modedb[] = {
+    {
+	/* 640x480 @ 60 Hz */
+	NULL, 60, 640, 480, 40000, 48, 16, 39, 11, 96, 2,
+	0, FB_VMODE_NONINTERLACED
+    }, {
+	/* 800x600 @ 60 Hz */
+	NULL, 60, 800, 600, 25000, 88, 40, 23, 1, 128, 4,
+	0, FB_VMODE_NONINTERLACED
+    }, {
+	/* 800x600 @ 72 Hz */
+	NULL, 72, 800, 600, 20000, 64, 56, 23, 37, 120, 6,
+	0, FB_VMODE_NONINTERLACED
+    }, {
+	/* 1024x768 @ 60 Hz */
+	NULL, 60, 1024, 768, 15385, 160, 24, 29, 3, 136, 6,
+	0, FB_VMODE_NONINTERLACED
+    }
+ };
+
+static struct fb_fix_screeninfo grvga_fix __initdata = {
+	.id =		"AG SVGACTRL",
+	.type =		FB_TYPE_PACKED_PIXELS,
+	.visual =       FB_VISUAL_PSEUDOCOLOR,
+	.xpanstep =	0,
+	.ypanstep =	1,
+	.ywrapstep =	0,
+	.accel =	FB_ACCEL_NONE,
+};
+
+static int grvga_check_var(struct fb_var_screeninfo *var,
+			   struct fb_info *info)
+{
+	struct grvga_par *par = info->par;
+	int i;
+
+	if (!var->xres)
+		var->xres = 1;
+	if (!var->yres)
+		var->yres = 1;
+	if (var->bits_per_pixel <= 8)
+		var->bits_per_pixel = 8;
+	else if (var->bits_per_pixel <= 16)
+		var->bits_per_pixel = 16;
+	else if (var->bits_per_pixel <= 24)
+		var->bits_per_pixel = 24;
+	else if (var->bits_per_pixel <= 32)
+		var->bits_per_pixel = 32;
+	else
+		return -EINVAL;
+
+	var->xres_virtual = var->xres;
+	var->yres_virtual = 2*var->yres;
+
+	if (info->fix.smem_len) {
+		if ((var->yres_virtual*var->xres_virtual*var->bits_per_pixel/8) > info->fix.smem_len)
+			return -ENOMEM;
+	}
+
+	/* Which clocks that are available can be read out in these registers */
+	for (i = 0; i <= 3 ; i++) {
+		if (var->pixclock == par->regs->clk_vector[i])
+			break;
+	}
+	if (i <= 3)
+		par->clk_sel = i;
+	else
+		return -EINVAL;
+
+	switch (info->var.bits_per_pixel) {
+	case 8:
+		var->red   = (struct fb_bitfield) {0, 8, 0};      /* offset, length, msb-right */
+		var->green = (struct fb_bitfield) {0, 8, 0};
+		var->blue  = (struct fb_bitfield) {0, 8, 0};
+		var->transp = (struct fb_bitfield) {0, 0, 0};
+		break;
+	case 16:
+		var->red   = (struct fb_bitfield) {11, 5, 0};
+		var->green = (struct fb_bitfield) {5, 6, 0};
+		var->blue  = (struct fb_bitfield) {0, 5, 0};
+		var->transp = (struct fb_bitfield) {0, 0, 0};
+		break;
+	case 24:
+	case 32:
+		var->red   = (struct fb_bitfield) {16, 8, 0};
+		var->green = (struct fb_bitfield) {8, 8, 0};
+		var->blue  = (struct fb_bitfield) {0, 8, 0};
+		var->transp = (struct fb_bitfield) {24, 8, 0};
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int grvga_set_par(struct fb_info *info)
+{
+
+	u32 func = 0;
+	struct grvga_par *par = info->par;
+
+	__raw_writel(((info->var.yres - 1) << 16) | (info->var.xres - 1),
+		     &par->regs->video_length);
+
+	__raw_writel((info->var.lower_margin << 16) | (info->var.right_margin),
+		     &par->regs->front_porch);
+
+	__raw_writel((info->var.vsync_len << 16) | (info->var.hsync_len),
+		     &par->regs->sync_length);
+
+	__raw_writel(((info->var.yres + info->var.lower_margin + info->var.upper_margin + info->var.vsync_len - 1) << 16) |
+		     (info->var.xres + info->var.right_margin + info->var.left_margin + info->var.hsync_len - 1),
+		     &par->regs->line_length);
+
+	switch (info->var.bits_per_pixel) {
+	case 8:
+		info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
+		func = 1;
+		break;
+	case 16:
+		info->fix.visual = FB_VISUAL_TRUECOLOR;
+		func = 2;
+		break;
+	case 24:
+	case 32:
+		info->fix.visual = FB_VISUAL_TRUECOLOR;
+		func = 3;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	__raw_writel((par->clk_sel << 6) | (func << 4) | 1,
+		     &par->regs->status);
+
+	info->fix.line_length = (info->var.xres_virtual*info->var.bits_per_pixel)/8;
+	return 0;
+}
+
+static int grvga_setcolreg(unsigned regno, unsigned red, unsigned green, unsigned blue, unsigned transp, struct fb_info *info)
+{
+	struct grvga_par *par;
+	par = info->par;
+
+	if (regno >= 256)	/* Size of CLUT */
+		return -EINVAL;
+
+	if (info->var.grayscale) {
+		/* grayscale = 0.30*R + 0.59*G + 0.11*B */
+		red = green = blue = (red * 77 + green * 151 + blue * 28) >> 8;
+	}
+
+
+
+#define CNVT_TOHW(val, width) ((((val)<<(width))+0x7FFF-(val))>>16)
+
+	red    = CNVT_TOHW(red,   info->var.red.length);
+	green  = CNVT_TOHW(green, info->var.green.length);
+	blue   = CNVT_TOHW(blue,  info->var.blue.length);
+	transp = CNVT_TOHW(transp, info->var.transp.length);
+
+#undef CNVT_TOHW
+
+	/* In PSEUDOCOLOR we use the hardware CLUT */
+	if (info->fix.visual == FB_VISUAL_PSEUDOCOLOR)
+		__raw_writel((regno << 24) | (red << 16) | (green << 8) | blue,
+			     &par->regs->clut);
+
+	/* Truecolor uses the pseudo palette */
+	else if (info->fix.visual == FB_VISUAL_TRUECOLOR) {
+		u32 v;
+		if (regno >= 16)
+			return -EINVAL;
+
+
+		v =     (red    << info->var.red.offset)   |
+			(green  << info->var.green.offset) |
+			(blue   << info->var.blue.offset)  |
+			(transp << info->var.transp.offset);
+
+		((u32 *) (info->pseudo_palette))[regno] = v;
+	}
+	return 0;
+}
+
+static int grvga_pan_display(struct fb_var_screeninfo *var,
+			     struct fb_info *info)
+{
+	struct grvga_par *par = info->par;
+	struct fb_fix_screeninfo *fix = &info->fix;
+	u32 base_addr;
+
+	if (var->xoffset != 0)
+		return -EINVAL;
+
+	base_addr = fix->smem_start + (var->yoffset * fix->line_length);
+	base_addr &= ~3UL;
+
+	/* Set framebuffer base address  */
+	__raw_writel(base_addr,
+		     &par->regs->fb_pos);
+
+	return 0;
+}
+
+static struct fb_ops grvga_ops = {
+	.owner          = THIS_MODULE,
+	.fb_check_var   = grvga_check_var,
+	.fb_set_par	= grvga_set_par,
+	.fb_setcolreg   = grvga_setcolreg,
+	.fb_pan_display = grvga_pan_display,
+	.fb_fillrect	= cfb_fillrect,
+	.fb_copyarea	= cfb_copyarea,
+	.fb_imageblit	= cfb_imageblit
+};
+
+static int __init grvga_parse_custom(char *options,
+				     struct fb_var_screeninfo *screendata)
+{
+	char *this_opt;
+	int count = 0;
+	if (!options || !*options)
+		return -1;
+
+	while ((this_opt = strsep(&options, " ")) != NULL) {
+		if (!*this_opt)
+			continue;
+
+		switch (count) {
+		case 0:
+			screendata->pixclock = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 1:
+			screendata->xres = screendata->xres_virtual = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 2:
+			screendata->right_margin = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 3:
+			screendata->hsync_len = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 4:
+			screendata->left_margin = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 5:
+			screendata->yres = screendata->yres_virtual = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 6:
+			screendata->lower_margin = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 7:
+			screendata->vsync_len = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 8:
+			screendata->upper_margin = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		case 9:
+			screendata->bits_per_pixel = simple_strtoul(this_opt, NULL, 0);
+			count++;
+			break;
+		default:
+			return -1;
+		}
+	}
+	screendata->activate  = FB_ACTIVATE_NOW;
+	screendata->vmode     = FB_VMODE_NONINTERLACED;
+	return 0;
+}
+
+static int __devinit grvga_probe(struct platform_device *dev)
+{
+	struct fb_info *info;
+	int retval = -ENOMEM;
+	unsigned long virtual_start;
+	unsigned long grvga_fix_addr = 0;
+	unsigned long physical_start = 0;
+	unsigned long grvga_mem_size = 0;
+	struct grvga_par *par = NULL;
+	char *options = NULL, *mode_opt = NULL;
+
+	info = framebuffer_alloc(sizeof(struct grvga_par), &dev->dev);
+	if (!info) {
+		dev_err(&dev->dev, "framebuffer_alloc failed\n");
+		return -ENOMEM;
+	}
+
+	/* Expecting: "grvga: modestring, [addr:<framebuffer physical address>], [size:<framebuffer size>]
+	 *
+	 * If modestring is custom:<custom mode string> we parse the string which then contains all videoparameters
+	 * If address is left out, we allocate memory,
+	 * if size is left out we only allocate enough to support the given mode.
+	 */
+	if (fb_get_options("grvga", &options)) {
+		retval = -ENODEV;
+		goto err;
+	}
+
+	if (!options || !*options)
+		options =  "640x480-8@60";
+
+	while (1) {
+		char *this_opt = strsep(&options, ",");
+
+		if (!this_opt)
+			break;
+
+		if (!strncmp(this_opt, "custom", 6)) {
+			if (grvga_parse_custom(this_opt, &info->var) < 0) {
+				dev_err(&dev->dev, "Failed to parse custom mode (%s).\n", this_opt);
+				retval = -EINVAL;
+				goto err1;
+			}
+		} else if (!strncmp(this_opt, "addr", 4))
+			grvga_fix_addr = simple_strtoul(this_opt + 5, NULL, 16);
+		else if (!strncmp(this_opt, "size", 4))
+			grvga_mem_size = simple_strtoul(this_opt + 5, NULL, 0);
+		else
+			mode_opt = this_opt;
+	}
+
+	par = info->par;
+	info->fbops = &grvga_ops;
+	info->fix = grvga_fix;
+	info->pseudo_palette = par->color_palette;
+	info->flags = FBINFO_DEFAULT | FBINFO_PARTIAL_PAN_OK | FBINFO_HWACCEL_YPAN;
+	info->fix.smem_len = grvga_mem_size;
+
+	if (!request_mem_region(dev->resource[0].start, resource_size(&dev->resource[0]), "grlib-svgactrl regs")) {
+		dev_err(&dev->dev, "registers already mapped\n");
+		retval = -EBUSY;
+		goto err;
+	}
+
+	par->regs = of_ioremap(&dev->resource[0], 0,
+			       resource_size(&dev->resource[0]),
+			       "grlib-svgactrl regs");
+
+	if (!par->regs) {
+		dev_err(&dev->dev, "failed to map registers\n");
+		retval = -ENOMEM;
+		goto err1;
+	}
+
+	retval = fb_alloc_cmap(&info->cmap, 256, 0);
+	if (retval < 0) {
+		dev_err(&dev->dev, "failed to allocate mem with fb_alloc_cmap\n");
+		retval = -ENOMEM;
+		goto err2;
+	}
+
+	if (mode_opt) {
+		retval = fb_find_mode(&info->var, info, mode_opt,
+				      grvga_modedb, sizeof(grvga_modedb), &grvga_modedb[0], 8);
+		if (!retval || retval == 4) {
+			retval = -EINVAL;
+			goto err3;
+		}
+	}
+
+	if (!grvga_mem_size)
+		grvga_mem_size = info->var.xres_virtual * info->var.yres_virtual * info->var.bits_per_pixel/8;
+
+	if (grvga_fix_addr) {
+		/* Got framebuffer base address from argument list */
+
+		physical_start = grvga_fix_addr;
+
+		if (!request_mem_region(physical_start, grvga_mem_size, dev->name)) {
+			dev_err(&dev->dev, "failed to request memory region\n");
+			retval = -ENOMEM;
+			goto err3;
+		}
+
+		virtual_start = (unsigned long) ioremap(physical_start, grvga_mem_size);
+
+		if (!virtual_start) {
+			dev_err(&dev->dev, "error mapping framebuffer memory\n");
+			retval = -ENOMEM;
+			goto err4;
+		}
+	} else {	/* Allocate frambuffer memory */
+
+		unsigned long page;
+
+		virtual_start = (unsigned long) __get_free_pages(GFP_DMA,
+								 get_order(grvga_mem_size));
+		if (!virtual_start) {
+			dev_err(&dev->dev,
+				"unable to allocate framebuffer memory (%lu bytes)\n",
+				grvga_mem_size);
+			retval = -ENOMEM;
+			goto err3;
+		}
+
+		physical_start = dma_map_single(&dev->dev, (void *)virtual_start, grvga_mem_size, DMA_TO_DEVICE);
+
+		/* Set page reserved so that mmap will work. This is necessary
+		 * since we'll be remapping normal memory.
+		 */
+		for (page = virtual_start;
+		     page < PAGE_ALIGN(virtual_start + grvga_mem_size);
+		     page += PAGE_SIZE) {
+			SetPageReserved(virt_to_page(page));
+		}
+
+		par->fb_alloced = 1;
+	}
+
+	memset((unsigned long *) virtual_start, 0, grvga_mem_size);
+
+	info->screen_base = (char __iomem *) virtual_start;
+	info->fix.smem_start = physical_start;
+	info->fix.smem_len   = grvga_mem_size;
+
+	dev_set_drvdata(&dev->dev, info);
+
+	dev_info(&dev->dev,
+		 "Aeroflex Gaisler framebuffer device (fb%d), %dx%d-%d, using %luK of video memory @ %p\n",
+		 info->node, info->var.xres, info->var.yres, info->var.bits_per_pixel,
+		 grvga_mem_size >> 10, info->screen_base);
+
+	retval = register_framebuffer(info);
+	if (retval < 0) {
+		dev_err(&dev->dev, "failed to register framebuffer\n");
+		goto err4;
+	}
+
+	__raw_writel(physical_start, &par->regs->fb_pos);
+	__raw_writel(__raw_readl(&par->regs->status) | 1,  /* Enable framebuffer */
+		     &par->regs->status);
+
+	return 0;
+
+err4:
+	dev_set_drvdata(&dev->dev, NULL);
+	if (grvga_fix_addr) {
+		release_mem_region(physical_start, grvga_mem_size);
+		iounmap((void *)virtual_start);
+	} else
+		kfree((void *)virtual_start);
+err3:
+	fb_dealloc_cmap(&info->cmap);
+err2:
+	of_iounmap(&dev->resource[0], par->regs,
+		   resource_size(&dev->resource[0]));
+err1:
+	release_mem_region(dev->resource[0].start, resource_size(&dev->resource[0]));
+err:
+	framebuffer_release(info);
+
+	return retval;
+}
+
+static int __devexit grvga_remove(struct platform_device *device)
+{
+	struct fb_info *info = dev_get_drvdata(&device->dev);
+	struct grvga_par *par = info->par;
+
+	if (info) {
+		unregister_framebuffer(info);
+		fb_dealloc_cmap(&info->cmap);
+
+		of_iounmap(&device->resource[0], par->regs,
+			   resource_size(&device->resource[0]));
+		release_mem_region(device->resource[0].start, resource_size(&device->resource[0]));
+
+		if (!par->fb_alloced) {
+			release_mem_region(info->fix.smem_start, info->fix.smem_len);
+			iounmap(info->screen_base);
+		} else
+			kfree((void *)info->screen_base);
+
+		framebuffer_release(info);
+		dev_set_drvdata(&device->dev, NULL);
+	}
+
+	return 0;
+}
+
+static struct of_device_id svgactrl_of_match[] = {
+	{
+		.name = "GAISLER_SVGACTRL",
+	},
+	{
+		.name = "01_063",
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, svgactrl_of_match);
+
+static struct platform_driver grvga_driver = {
+	.driver = {
+		.name = "grlib-svgactrl",
+		.owner = THIS_MODULE,
+		.of_match_table = svgactrl_of_match,
+	},
+	.probe		= grvga_probe,
+	.remove		= __devexit_p(grvga_remove),
+};
+
+
+static int __init grvga_init(void)
+{
+	return platform_driver_register(&grvga_driver);
+}
+
+static void __exit grvga_exit(void)
+{
+	platform_driver_unregister(&grvga_driver);
+}
+
+module_init(grvga_init);
+module_exit(grvga_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Aeroflex Gaisler");
+MODULE_DESCRIPTION("Aeroflex Gaisler framebuffer device driver");

drivers/video/msm/mdp.c

@@ -421,7 +421,8 @@ int mdp_probe(struct platform_device *pdev)
 	clk = clk_get(&pdev->dev, "mdp_clk");
 	if (IS_ERR(clk)) {
 		printk(KERN_INFO "mdp: failed to get mdp clk");
-		return PTR_ERR(clk);
+		ret = PTR_ERR(clk);
+		goto error_get_clk;
 	}
 
 	ret = request_irq(mdp->irq, mdp_isr, IRQF_DISABLED, "msm_mdp", mdp);
@@ -495,6 +496,7 @@ int mdp_probe(struct platform_device *pdev)
 error_device_register:
 	free_irq(mdp->irq, mdp);
 error_request_irq:
+error_get_clk:
 	iounmap(mdp->base);
 error_get_irq:
 error_ioremap:

drivers/video/platinumfb.c

@@ -490,7 +490,7 @@ static int platinum_var_to_par(struct fb_var_screeninfo *var,
 
 
 /* 
- * Parse user speficied options (`video=platinumfb:')
+ * Parse user specified options (`video=platinumfb:')
  */
 static int __init platinumfb_setup(char *options)
 {

drivers/video/pm2fb.c

@@ -1773,7 +1773,7 @@ MODULE_DEVICE_TABLE(pci, pm2fb_id_table);
 
 #ifndef MODULE
 /**
- * Parse user speficied options.
+ * Parse user specified options.
  *
  * This is, comma-separated options following `video=pm2fb:'.
  */

drivers/video/pm3fb.c

@@ -1525,7 +1525,7 @@ static int __init pm3fb_setup(char *options)
 {
 	char *this_opt;
 
-	/* Parse user speficied options (`video=pm3fb:') */
+	/* Parse user specified options (`video=pm3fb:') */
 	if (!options || !*options)
 		return 0;
 

drivers/video/pxa3xx-gcu.c

@@ -31,8 +31,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/version.h>
-
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 #include <linux/miscdevice.h>

drivers/video/s3c2410fb.c

@@ -767,7 +767,6 @@ static irqreturn_t s3c2410fb_irq(int irq, void *dev_id)
 static int s3c2410fb_cpufreq_transition(struct notifier_block *nb,
 					unsigned long val, void *data)
 {
-	struct cpufreq_freqs *freqs = data;
 	struct s3c2410fb_info *info;
 	struct fb_info *fbinfo;
 	long delta_f;

drivers/video/s3fb.c

@@ -1505,7 +1505,7 @@ static struct pci_driver s3fb_pci_driver = {
 	.resume		= s3_pci_resume,
 };
 
-/* Parse user speficied options */
+/* Parse user specified options */
 
 #ifndef MODULE
 static int  __init s3fb_setup(char *options)

drivers/video/skeletonfb.c

@@ -989,7 +989,7 @@ static struct platform_device *xxxfb_device;
  */
 int __init xxxfb_setup(char *options)
 {
-    /* Parse user speficied options (`video=xxxfb:') */
+    /* Parse user specified options (`video=xxxfb:') */
 }
 #endif /* MODULE */
 

drivers/video/udlfb.c

@@ -48,13 +48,22 @@ static const u32 udlfb_info_flags = FBINFO_DEFAULT | FBINFO_READS_FAST |
 		FBINFO_HWACCEL_COPYAREA | FBINFO_MISC_ALWAYS_SETPAR;
 
 /*
- * There are many DisplayLink-based products, all with unique PIDs. We are able
- * to support all volume ones (circa 2009) with a single driver, so we match
- * globally on VID. TODO: Probe() needs to detect when we might be running
- * "future" chips, and bail on those, so a compatible driver can match.
+ * There are many DisplayLink-based graphics products, all with unique PIDs.
+ * So we match on DisplayLink's VID + Vendor-Defined Interface Class (0xff)
+ * We also require a match on SubClass (0x00) and Protocol (0x00),
+ * which is compatible with all known USB 2.0 era graphics chips and firmware,
+ * but allows DisplayLink to increment those for any future incompatible chips
  */
 static struct usb_device_id id_table[] = {
-	{.idVendor = 0x17e9, .match_flags = USB_DEVICE_ID_MATCH_VENDOR,},
+	{.idVendor = 0x17e9,
+	 .bInterfaceClass = 0xff,
+	 .bInterfaceSubClass = 0x00,
+	 .bInterfaceProtocol = 0x00,
+	 .match_flags = USB_DEVICE_ID_MATCH_VENDOR |
+		USB_DEVICE_ID_MATCH_INT_CLASS |
+		USB_DEVICE_ID_MATCH_INT_SUBCLASS |
+		USB_DEVICE_ID_MATCH_INT_PROTOCOL,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(usb, id_table);
@@ -1613,7 +1622,7 @@ static int dlfb_usb_probe(struct usb_interface *interface,
 	/* We don't register a new USB class. Our client interface is fbdev */
 
 	/* allocates framebuffer driver structure, not framebuffer memory */
-	info = framebuffer_alloc(0, &usbdev->dev);
+	info = framebuffer_alloc(0, &interface->dev);
 	if (!info) {
 		retval = -ENOMEM;
 		pr_err("framebuffer_alloc failed\n");

drivers/video/valkyriefb.c

@@ -555,7 +555,7 @@ static int __init valkyrie_init_info(struct fb_info *info,
 
 
 /*
- * Parse user speficied options (`video=valkyriefb:')
+ * Parse user specified options (`video=valkyriefb:')
  */
 int __init valkyriefb_setup(char *options)
 {

drivers/video/via/via_modesetting.h

@@ -28,6 +28,11 @@
 
 #include <linux/types.h>
 
+
+#define VIA_PITCH_SIZE	(1<<3)
+#define VIA_PITCH_MAX	0x3FF8
+
+
 void via_set_primary_address(u32 addr);
 void via_set_secondary_address(u32 addr);
 void via_set_primary_pitch(u32 pitch);

drivers/video/via/viafbdev.c

@@ -151,7 +151,8 @@ static void viafb_update_fix(struct fb_info *info)
 
 	info->fix.visual =
 		bpp == 8 ? FB_VISUAL_PSEUDOCOLOR : FB_VISUAL_TRUECOLOR;
-	info->fix.line_length = (info->var.xres_virtual * bpp / 8 + 7) & ~7;
+	info->fix.line_length = ALIGN(info->var.xres_virtual * bpp / 8,
+		VIA_PITCH_SIZE);
 }
 
 static void viafb_setup_fixinfo(struct fb_fix_screeninfo *fix,
@@ -238,8 +239,12 @@ static int viafb_check_var(struct fb_var_screeninfo *var,
 		depth = 24;
 
 	viafb_fill_var_color_info(var, depth);
-	line = (var->xres_virtual * var->bits_per_pixel / 8 + 7) & ~7;
-	if (line * var->yres_virtual > ppar->memsize)
+	if (var->xres_virtual < var->xres)
+		var->xres_virtual = var->xres;
+
+	line = ALIGN(var->xres_virtual * var->bits_per_pixel / 8,
+		VIA_PITCH_SIZE);
+	if (line > VIA_PITCH_MAX || line * var->yres_virtual > ppar->memsize)
 		return -EINVAL;
 
 	/* Based on var passed in to calculate the refresh,
@@ -348,8 +353,9 @@ static int viafb_pan_display(struct fb_var_screeninfo *var,
 	struct fb_info *info)
 {
 	struct viafb_par *viapar = info->par;
-	u32 vram_addr = (var->yoffset * var->xres_virtual + var->xoffset)
-		* (var->bits_per_pixel / 8) + viapar->vram_addr;
+	u32 vram_addr = viapar->vram_addr
+		+ var->yoffset * info->fix.line_length
+		+ var->xoffset * info->var.bits_per_pixel / 8;
 
 	DEBUG_MSG(KERN_DEBUG "viafb_pan_display, address = %d\n", vram_addr);
 	if (!viafb_dual_fb) {

drivers/video/xilinxfb.c

@@ -23,7 +23,6 @@
 #include <linux/device.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
-#include <linux/version.h>
 #include <linux/errno.h>
 #include <linux/string.h>
 #include <linux/mm.h>