Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (47 commits)
  Blackfin: bfin_spi.h: add MMR peripheral layout
  Blackfin: bfin_ppi.h: start a common PPI/EPPI header
  Blackfin: bfin_can.h: add missing VERSION/VERSION2 MMRs
  Blackfin: bf538: add missing SIC_RVECT define
  Blackfin: bf561: rewrite SICA_xxx to just SIC_xxx
  Blackfin: bf54x: add missing SIC_RVECT definition
  Blackfin: H8606: move 8250 irqflags to platform resources
  Blackfin: glue XIP/ROM kernel kconfigs
  Blackfin: update sparse flags for latest upstream changes
  Blackfin: coreb: update ioctl numbers
  Blackfin: coreb: add gpl module license
  Blackfin: bf518-ezkit: add ssm2603 codec resources
  Blackfin: bf51x/bf52x: fix 16/32bit SPORT MMR helpers
  Blackfin: tll6527m: new board port
  Blackfin: bf526-ezbrd/bf527-ezkit: add NAND partition for u-boot
  Blackfin: merge kernel init memory back into main memory region
  Blackfin: gpio: add peripheral group check
  Blackfin: dma: bf54x: add missing break for SPORT1 TX IRQ
  Blackfin: add new cacheflush syscall
  Blackfin: bf548-ezkit: increase u-boot partition size
  ...

arch/blackfin/Kconfig

@@ -300,7 +300,7 @@ config BF_REV_0_1
 
 config BF_REV_0_2
 	bool "0.2"
-	depends on (BF52x || BF537 || BF536 || BF534 || (BF54x && !BF54xM))
+	depends on (BF51x || BF52x || BF537 || BF536 || BF534 || (BF54x && !BF54xM))
 
 config BF_REV_0_3
 	bool "0.3"
@@ -356,7 +356,7 @@ config MEM_MT48LC8M32B2B5_7
 
 config MEM_MT48LC32M16A2TG_75
 	bool
-	depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP)
+	depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP || BFIN527_AD7160EVAL)
 	default y
 
 config MEM_MT48H32M16LFCJ_75
@@ -426,6 +426,7 @@ config CLKIN_HZ
 	default "25000000" # most people use this
 	default "27000000" if BFIN533_EZKIT
 	default "30000000" if BFIN561_EZKIT
+	default "24000000" if BFIN527_AD7160EVAL
 	help
 	  The frequency of CLKIN crystal oscillator on the board in Hz.
 	  Warning: This value should match the crystal on the board. Otherwise,
@@ -463,6 +464,7 @@ config VCO_MULT
 	default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
 	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
+	default "25" if BFIN527_AD7160EVAL
 	help
 	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
 	  PLL Frequency = (Crystal Frequency) * (this setting)
@@ -926,6 +928,12 @@ config ROMKERNEL
 
 endchoice
 
+# Common code uses "ROMKERNEL" or "XIP_KERNEL", so define both
+config XIP_KERNEL
+	bool
+	default y
+	depends on ROMKERNEL
+
 source "mm/Kconfig"
 
 config BFIN_GPTIMERS

arch/blackfin/Makefile

@@ -101,9 +101,8 @@ KBUILD_CFLAGS += -mcpu=$(cpu-y)-$(rev-y)
 KBUILD_AFLAGS += -mcpu=$(cpu-y)-$(rev-y)
 
 # - we utilize the silicon rev from the toolchain, so move it over to the checkflags
-# - the l1_text attribute is Blackfin specific, so fake it out as used to kill warnings
 CHECKFLAGS_SILICON = $(shell echo "" | $(CPP) $(KBUILD_CFLAGS) -dD - 2>/dev/null | awk '$$2 == "__SILICON_REVISION__" { print $$3 }')
-CHECKFLAGS += -D__SILICON_REVISION__=$(CHECKFLAGS_SILICON) -Dl1_text=__used__
+CHECKFLAGS += -D__SILICON_REVISION__=$(CHECKFLAGS_SILICON) -D__bfin__
 
 head-y   := arch/$(ARCH)/kernel/init_task.o
 

arch/blackfin/configs/BF527-AD7160-EVAL_defconfig

@@ -0,0 +1,105 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_AIO is not set
+CONFIG_SLAB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_PREEMPT=y
+CONFIG_BF527=y
+CONFIG_BF_REV_0_2=y
+CONFIG_IRQ_TWI=7
+CONFIG_IRQ_PORTH_INTA=7
+CONFIG_IRQ_PORTH_INTB=7
+CONFIG_BFIN527_AD7160EVAL=y
+CONFIG_BF527_SPORT0_PORTF=y
+CONFIG_BF527_UART1_PORTG=y
+CONFIG_IRQ_USB_INT0=11
+CONFIG_IRQ_USB_INT1=11
+CONFIG_IRQ_USB_INT2=11
+CONFIG_IRQ_USB_DMA=11
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="bootargs=root=/dev/mtdblock0 rw clkin_hz=24000000 earlyprintk=serial,uart0,57600 console=tty0 console=ttyBF0,57600"
+CONFIG_CLKIN_HZ=24000000
+CONFIG_HZ_300=y
+# CONFIG_CYCLES_CLOCKSOURCE is not set
+CONFIG_IP_CHECKSUM_L1=y
+CONFIG_SYSCALL_TAB_L1=y
+CONFIG_CPLB_SWITCH_TAB_L1=y
+CONFIG_BFIN_GPTIMERS=y
+CONFIG_C_CDPRIO=y
+CONFIG_BANK_1=0x5554
+CONFIG_BANK_3=0xFFC0
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+CONFIG_NET=y
+CONFIG_UNIX=y
+# CONFIG_WIRELESS is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_AD7160=y
+CONFIG_TOUCHSCREEN_AD7160_FW=y
+# CONFIG_SERIO is not set
+# CONFIG_BFIN_DMA_INTERFACE is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_UART0=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_BFIN_OTP is not set
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_I2C_ALGOBIT=y
+CONFIG_I2C_BLACKFIN_TWI=y
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=400
+CONFIG_SPI=y
+CONFIG_SPI_BFIN=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_LOGO_BLACKFIN_VGA16 is not set
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VBUS_DRAW=500
+CONFIG_USB_G_SERIAL=y
+CONFIG_MMC=y
+CONFIG_MMC_SPI=y
+CONFIG_EXT2_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+CONFIG_EARLY_PRINTK=y
+CONFIG_CPLB_INFO=y
+CONFIG_SECURITY=y
+CONFIG_CRC_CCITT=m

arch/blackfin/configs/BF527-TLL6527M_defconfig

@@ -0,0 +1,180 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_LOCALVERSION="DEV_0-1_pre2010"
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+# CONFIG_ELF_CORE is not set
+# CONFIG_FUTEX is not set
+# CONFIG_SIGNALFD is not set
+# CONFIG_TIMERFD is not set
+# CONFIG_EVENTFD is not set
+# CONFIG_AIO is not set
+CONFIG_SLAB=y
+CONFIG_MMAP_ALLOW_UNINITIALIZED=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_BF527=y
+CONFIG_BF_REV_0_2=y
+CONFIG_BFIN527_TLL6527M=y
+CONFIG_BF527_UART1_PORTG=y
+CONFIG_IRQ_USB_INT0=11
+CONFIG_IRQ_USB_INT1=11
+CONFIG_IRQ_USB_INT2=11
+CONFIG_IRQ_USB_DMA=11
+CONFIG_BOOT_LOAD=0x400000
+# CONFIG_CYCLES_CLOCKSOURCE is not set
+# CONFIG_SCHEDULE_L1 is not set
+# CONFIG_MEMSET_L1 is not set
+# CONFIG_MEMCPY_L1 is not set
+# CONFIG_SYS_BFIN_SPINLOCK_L1 is not set
+CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0
+CONFIG_BFIN_GPTIMERS=y
+CONFIG_DMA_UNCACHED_2M=y
+CONFIG_C_CDPRIO=y
+CONFIG_BANK_0=0xFFC2
+CONFIG_BANK_1=0xFFC2
+CONFIG_BANK_2=0xFFC2
+CONFIG_BANK_3=0xFFC2
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_IRDA=m
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+CONFIG_IRTTY_SIR=m
+CONFIG_BFIN_SIR=m
+CONFIG_BFIN_SIR0=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_RAM=y
+CONFIG_MTD_ROM=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_GPIO_ADDR=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_SCSI=y
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_NET_ETHERNET=y
+CONFIG_BFIN_MAC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_AD7879=m
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_AD714X=y
+CONFIG_INPUT_ADXL34X=y
+# CONFIG_SERIO is not set
+CONFIG_BFIN_PPI=m
+CONFIG_BFIN_SIMPLE_TIMER=m
+CONFIG_BFIN_SPORT=m
+# CONFIG_CONSOLE_TRANSLATIONS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_BFIN_JTAG_COMM=m
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_UART1=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C_CHARDEV=y
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_I2C_SMBUS=y
+CONFIG_I2C_BLACKFIN_TWI=y
+CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_BFIN_WDT=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_VIDEO_DEV=y
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
+CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
+CONFIG_VIDEO_BLACKFIN_CAM=m
+CONFIG_OV9655=y
+CONFIG_FB=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FONTS=y
+CONFIG_FONT_6x11=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_LOGO_BLACKFIN_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_SOC=y
+CONFIG_SND_BF5XX_I2S=y
+CONFIG_SND_BF5XX_SOC_SSM2602=y
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_BFIN=y
+CONFIG_EXT2_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_UTF8=m
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_MMRS=y
+CONFIG_DEBUG_HWERR=y
+CONFIG_EXACT_HWERR=y
+CONFIG_DEBUG_DOUBLEFAULT=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_CPLB_INFO=y
+CONFIG_SECURITY=y
+CONFIG_CRYPTO=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRC7=m

arch/blackfin/include/asm/Kbuild

@@ -1,4 +1,5 @@
 include include/asm-generic/Kbuild.asm
 
 header-y += bfin_sport.h
+header-y += cachectl.h
 header-y += fixed_code.h

arch/blackfin/include/asm/bfin5xx_spi.h

@@ -41,6 +41,25 @@
 #define BIT_STU_SENDOVER    0x0001
 #define BIT_STU_RECVFULL    0x0020
 
+/*
+ * All Blackfin system MMRs are padded to 32bits even if the register
+ * itself is only 16bits.  So use a helper macro to streamline this.
+ */
+#define __BFP(m) u16 m; u16 __pad_##m
+
+/*
+ * bfin spi registers layout
+ */
+struct bfin_spi_regs {
+	__BFP(ctl);
+	__BFP(flg);
+	__BFP(stat);
+	__BFP(tdbr);
+	__BFP(rdbr);
+	__BFP(baud);
+	__BFP(shadow);
+};
+
 #define MAX_CTRL_CS          8  /* cs in spi controller */
 
 /* device.platform_data for SSP controller devices */

arch/blackfin/include/asm/bfin_can.h

@@ -34,6 +34,7 @@ struct bfin_can_mask_regs {
 };
 
 struct bfin_can_channel_regs {
+	/* data[0,2,4,6] -> data{0,1,2,3} while data[1,3,5,7] is padding */
 	u16 data[8];
 	__BFP(dlc);
 	__BFP(tsv);
@@ -83,16 +84,18 @@ struct bfin_can_regs {
 	__BFP(gif);           /* offset 0x9c */
 	__BFP(control);       /* offset 0xa0 */
 	__BFP(intr);          /* offset 0xa4 */
-	u32 __pad3[1];
+	__BFP(version);       /* offset 0xa8 */
 	__BFP(mbtd);          /* offset 0xac */
 	__BFP(ewr);           /* offset 0xb0 */
 	__BFP(esr);           /* offset 0xb4 */
-	u32 __pad4[2];
+	u32 __pad3[2];
 	__BFP(ucreg);         /* offset 0xc0 */
 	__BFP(uccnt);         /* offset 0xc4 */
 	__BFP(ucrc);          /* offset 0xc8 */
 	__BFP(uccnf);         /* offset 0xcc */
-	u32 __pad5[12];
+	u32 __pad4[1];
+	__BFP(version2);      /* offset 0xd4 */
+	u32 __pad5[10];
 
 	/*
 	 * channel(mailbox) mask and message registers

arch/blackfin/include/asm/bfin_ppi.h

@@ -0,0 +1,51 @@
+/*
+ * bfin_ppi.h - interface to Blackfin PPIs
+ *
+ * Copyright 2005-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __ASM_BFIN_PPI_H__
+#define __ASM_BFIN_PPI_H__
+
+#include <linux/types.h>
+
+/*
+ * All Blackfin system MMRs are padded to 32bits even if the register
+ * itself is only 16bits.  So use a helper macro to streamline this.
+ */
+#define __BFP(m) u16 m; u16 __pad_##m
+
+/*
+ * bfin ppi registers layout
+ */
+struct bfin_ppi_regs {
+	__BFP(control);
+	__BFP(status);
+	__BFP(count);
+	__BFP(delay);
+	__BFP(frame);
+};
+
+/*
+ * bfin eppi registers layout
+ */
+struct bfin_eppi_regs {
+	__BFP(status);
+	__BFP(hcount);
+	__BFP(hdelay);
+	__BFP(vcount);
+	__BFP(vdelay);
+	__BFP(frame);
+	__BFP(line);
+	__BFP(clkdiv);
+	u32 control;
+	u32 fs1w_hbl;
+	u32 fs1p_avpl;
+	u32 fs2w_lvb;
+	u32 fs2p_lavf;
+	u32 clip;
+};
+
+#endif

arch/blackfin/include/asm/cachectl.h

@@ -0,0 +1,20 @@
+/*
+ * based on the mips/cachectl.h
+ *
+ * Copyright 2010 Analog Devices Inc.
+ * Copyright (C) 1994, 1995, 1996 by Ralf Baechle
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef	_ASM_CACHECTL
+#define	_ASM_CACHECTL
+
+/*
+ * Options for cacheflush system call
+ */
+#define	ICACHE	(1<<0)		/* flush instruction cache        */
+#define	DCACHE	(1<<1)		/* writeback and flush data cache */
+#define	BCACHE	(ICACHE|DCACHE)	/* flush both caches              */
+
+#endif	/* _ASM_CACHECTL */

arch/blackfin/include/asm/cdef_LPBlackfin.h

@@ -172,16 +172,19 @@
 #define bfin_write_ICPLB_DATA14(val)         bfin_write32(ICPLB_DATA14,val)
 #define bfin_read_ICPLB_DATA15()             bfin_read32(ICPLB_DATA15)
 #define bfin_write_ICPLB_DATA15(val)         bfin_write32(ICPLB_DATA15,val)
-#define bfin_read_ITEST_COMMAND()            bfin_read32(ITEST_COMMAND)
 #define bfin_write_ITEST_COMMAND(val)        bfin_write32(ITEST_COMMAND,val)
 #if 0
 #define ITEST_INDEX            0xFFE01304   /* Instruction Test Index Register */
 #endif
-#define bfin_read_ITEST_DATA0()              bfin_read32(ITEST_DATA0)
 #define bfin_write_ITEST_DATA0(val)          bfin_write32(ITEST_DATA0,val)
-#define bfin_read_ITEST_DATA1()              bfin_read32(ITEST_DATA1)
 #define bfin_write_ITEST_DATA1(val)          bfin_write32(ITEST_DATA1,val)
 
+#if ANOMALY_05000481
+#define bfin_read_ITEST_COMMAND()            bfin_read32(ITEST_COMMAND)
+#define bfin_read_ITEST_DATA0()              bfin_read32(ITEST_DATA0)
+#define bfin_read_ITEST_DATA1()              bfin_read32(ITEST_DATA1)
+#endif
+
 /* Event/Interrupt Registers*/
 
 #define bfin_read_EVT0()                     bfin_read32(EVT0)

arch/blackfin/include/asm/ptrace.h

@@ -113,6 +113,9 @@ extern void user_disable_single_step(struct task_struct *child);
 /* common code demands this function */
 #define ptrace_disable(child) user_disable_single_step(child)
 
+extern int is_user_addr_valid(struct task_struct *child,
+			      unsigned long start, unsigned long len);
+
 /*
  * Get the address of the live pt_regs for the specified task.
  * These are saved onto the top kernel stack when the process

arch/blackfin/include/asm/serial.h

@@ -1,2 +1 @@
 #include <asm-generic/serial.h>
-#define SERIAL_EXTRA_IRQ_FLAGS IRQF_TRIGGER_HIGH

arch/blackfin/include/asm/unistd.h

@@ -392,8 +392,9 @@
 #define __NR_fanotify_init	371
 #define __NR_fanotify_mark	372
 #define __NR_prlimit64		373
+#define __NR_cacheflush		374
 
-#define __NR_syscall		374
+#define __NR_syscall		375
 #define NR_syscalls		__NR_syscall
 
 /* Old optional stuff no one actually uses */

arch/blackfin/kernel/bfin_gpio.c

@@ -1,7 +1,7 @@
 /*
  * GPIO Abstraction Layer
  *
- * Copyright 2006-2009 Analog Devices Inc.
+ * Copyright 2006-2010 Analog Devices Inc.
  *
  * Licensed under the GPL-2 or later
  */
@@ -215,82 +215,91 @@ static void port_setup(unsigned gpio, unsigned short usage)
 }
 
 #ifdef BF537_FAMILY
-static struct {
-	unsigned short res;
-	unsigned short offset;
-} port_mux_lut[] = {
-	{.res = P_PPI0_D13, .offset = 11},
-	{.res = P_PPI0_D14, .offset = 11},
-	{.res = P_PPI0_D15, .offset = 11},
-	{.res = P_SPORT1_TFS, .offset = 11},
-	{.res = P_SPORT1_TSCLK, .offset = 11},
-	{.res = P_SPORT1_DTPRI, .offset = 11},
-	{.res = P_PPI0_D10, .offset = 10},
-	{.res = P_PPI0_D11, .offset = 10},
-	{.res = P_PPI0_D12, .offset = 10},
-	{.res = P_SPORT1_RSCLK, .offset = 10},
-	{.res = P_SPORT1_RFS, .offset = 10},
-	{.res = P_SPORT1_DRPRI, .offset = 10},
-	{.res = P_PPI0_D8, .offset = 9},
-	{.res = P_PPI0_D9, .offset = 9},
-	{.res = P_SPORT1_DRSEC, .offset = 9},
-	{.res = P_SPORT1_DTSEC, .offset = 9},
-	{.res = P_TMR2, .offset = 8},
-	{.res = P_PPI0_FS3, .offset = 8},
-	{.res = P_TMR3, .offset = 7},
-	{.res = P_SPI0_SSEL4, .offset = 7},
-	{.res = P_TMR4, .offset = 6},
-	{.res = P_SPI0_SSEL5, .offset = 6},
-	{.res = P_TMR5, .offset = 5},
-	{.res = P_SPI0_SSEL6, .offset = 5},
-	{.res = P_UART1_RX, .offset = 4},
-	{.res = P_UART1_TX, .offset = 4},
-	{.res = P_TMR6, .offset = 4},
-	{.res = P_TMR7, .offset = 4},
-	{.res = P_UART0_RX, .offset = 3},
-	{.res = P_UART0_TX, .offset = 3},
-	{.res = P_DMAR0, .offset = 3},
-	{.res = P_DMAR1, .offset = 3},
-	{.res = P_SPORT0_DTSEC, .offset = 1},
-	{.res = P_SPORT0_DRSEC, .offset = 1},
-	{.res = P_CAN0_RX, .offset = 1},
-	{.res = P_CAN0_TX, .offset = 1},
-	{.res = P_SPI0_SSEL7, .offset = 1},
-	{.res = P_SPORT0_TFS, .offset = 0},
-	{.res = P_SPORT0_DTPRI, .offset = 0},
-	{.res = P_SPI0_SSEL2, .offset = 0},
-	{.res = P_SPI0_SSEL3, .offset = 0},
+static const s8 port_mux[] = {
+	[GPIO_PF0] = 3,
+	[GPIO_PF1] = 3,
+	[GPIO_PF2] = 4,
+	[GPIO_PF3] = 4,
+	[GPIO_PF4] = 5,
+	[GPIO_PF5] = 6,
+	[GPIO_PF6] = 7,
+	[GPIO_PF7] = 8,
+	[GPIO_PF8 ... GPIO_PF15] = -1,
+	[GPIO_PG0 ... GPIO_PG7] = -1,
+	[GPIO_PG8] = 9,
+	[GPIO_PG9] = 9,
+	[GPIO_PG10] = 10,
+	[GPIO_PG11] = 10,
+	[GPIO_PG12] = 10,
+	[GPIO_PG13] = 11,
+	[GPIO_PG14] = 11,
+	[GPIO_PG15] = 11,
+	[GPIO_PH0 ... GPIO_PH15] = -1,
+	[PORT_PJ0 ... PORT_PJ3] = -1,
+	[PORT_PJ4] = 1,
+	[PORT_PJ5] = 1,
+	[PORT_PJ6 ... PORT_PJ9] = -1,
+	[PORT_PJ10] = 0,
+	[PORT_PJ11] = 0,
 };
 
-static void portmux_setup(unsigned short per)
+static int portmux_group_check(unsigned short per)
 {
-	u16 y, offset, muxreg;
+	u16 ident = P_IDENT(per);
 	u16 function = P_FUNCT2MUX(per);
+	s8 offset = port_mux[ident];
+	u16 m, pmux, pfunc;
 
-	for (y = 0; y < ARRAY_SIZE(port_mux_lut); y++) {
-		if (port_mux_lut[y].res == per) {
-
-			/* SET PORTMUX REG */
-
-			offset = port_mux_lut[y].offset;
-			muxreg = bfin_read_PORT_MUX();
+	if (offset < 0)
+		return 0;
 
-			if (offset != 1)
-				muxreg &= ~(1 << offset);
-			else
-				muxreg &= ~(3 << 1);
+	pmux = bfin_read_PORT_MUX();
+	for (m = 0; m < ARRAY_SIZE(port_mux); ++m) {
+		if (m == ident)
+			continue;
+		if (port_mux[m] != offset)
+			continue;
+		if (!is_reserved(peri, m, 1))
+			continue;
 
-			muxreg |= (function << offset);
-			bfin_write_PORT_MUX(muxreg);
+		if (offset == 1)
+			pfunc = (pmux >> offset) & 3;
+		else
+			pfunc = (pmux >> offset) & 1;
+		if (pfunc != function) {
+			pr_err("pin group conflict! request pin %d func %d conflict with pin %d func %d\n",
+				ident, function, m, pfunc);
+			return -EINVAL;
 		}
 	}
+
+	return 0;
+}
+
+static void portmux_setup(unsigned short per)
+{
+	u16 ident = P_IDENT(per);
+	u16 function = P_FUNCT2MUX(per);
+	s8 offset = port_mux[ident];
+	u16 pmux;
+
+	if (offset == -1)
+		return;
+
+	pmux = bfin_read_PORT_MUX();
+	if (offset != 1)
+		pmux &= ~(1 << offset);
+	else
+		pmux &= ~(3 << 1);
+	pmux |= (function << offset);
+	bfin_write_PORT_MUX(pmux);
 }
 #elif defined(CONFIG_BF54x)
 inline void portmux_setup(unsigned short per)
 {
-	u32 pmux;
 	u16 ident = P_IDENT(per);
 	u16 function = P_FUNCT2MUX(per);
+	u32 pmux;
 
 	pmux = gpio_array[gpio_bank(ident)]->port_mux;
 
@@ -302,20 +311,54 @@ inline void portmux_setup(unsigned short per)
 
 inline u16 get_portmux(unsigned short per)
 {
-	u32 pmux;
 	u16 ident = P_IDENT(per);
-
-	pmux = gpio_array[gpio_bank(ident)]->port_mux;
-
+	u32 pmux = gpio_array[gpio_bank(ident)]->port_mux;
 	return (pmux >> (2 * gpio_sub_n(ident)) & 0x3);
 }
+static int portmux_group_check(unsigned short per)
+{
+	return 0;
+}
 #elif defined(CONFIG_BF52x) || defined(CONFIG_BF51x)
+static int portmux_group_check(unsigned short per)
+{
+	u16 ident = P_IDENT(per);
+	u16 function = P_FUNCT2MUX(per);
+	u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)];
+	u16 pin, gpiopin, pfunc;
+
+	for (pin = 0; pin < GPIO_BANKSIZE; ++pin) {
+		if (offset != pmux_offset[gpio_bank(ident)][pin])
+			continue;
+
+		gpiopin = gpio_bank(ident) * GPIO_BANKSIZE + pin;
+		if (gpiopin == ident)
+			continue;
+		if (!is_reserved(peri, gpiopin, 1))
+			continue;
+
+		pfunc = *port_mux[gpio_bank(ident)];
+		pfunc = (pfunc >> offset) & 3;
+		if (pfunc != function) {
+			pr_err("pin group conflict! request pin %d func %d conflict with pin %d func %d\n",
+				ident, function, gpiopin, pfunc);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
 inline void portmux_setup(unsigned short per)
 {
-	u16 pmux, ident = P_IDENT(per), function = P_FUNCT2MUX(per);
+	u16 ident = P_IDENT(per);
+	u16 function = P_FUNCT2MUX(per);
 	u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)];
+	u16 pmux;
 
 	pmux = *port_mux[gpio_bank(ident)];
+	if  (((pmux >> offset) & 3) == function)
+		return;
 	pmux &= ~(3 << offset);
 	pmux |= (function & 3) << offset;
 	*port_mux[gpio_bank(ident)] = pmux;
@@ -323,6 +366,10 @@ inline void portmux_setup(unsigned short per)
 }
 #else
 # define portmux_setup(...)  do { } while (0)
+static int portmux_group_check(unsigned short per)
+{
+	return 0;
+}
 #endif
 
 #ifndef CONFIG_BF54x
@@ -735,6 +782,10 @@ int peripheral_request(unsigned short per, const char *label)
 		}
 	}
 
+	if (unlikely(portmux_group_check(per))) {
+		hard_local_irq_restore(flags);
+		return -EBUSY;
+	}
  anyway:
 	reserve(peri, ident);
 

arch/blackfin/kernel/process.c

@@ -493,6 +493,11 @@ int _access_ok(unsigned long addr, unsigned long size)
 		return 1;
 #endif
 
+#ifndef CONFIG_EXCEPTION_L1_SCRATCH
+	if (in_mem_const(addr, size, (unsigned long)l1_stack_base, l1_stack_len))
+		return 1;
+#endif
+
 	aret = in_async(addr, size);
 	if (aret < 2)
 		return aret;

arch/blackfin/kernel/ptrace.c

@@ -27,6 +27,7 @@
 #include <asm/fixed_code.h>
 #include <asm/cacheflush.h>
 #include <asm/mem_map.h>
+#include <asm/mmu_context.h>
 
 /*
  * does not yet catch signals sent when the child dies.
@@ -113,8 +114,8 @@ put_reg(struct task_struct *task, long regno, unsigned long data)
 /*
  * check that an address falls within the bounds of the target process's memory mappings
  */
-static inline int is_user_addr_valid(struct task_struct *child,
-				     unsigned long start, unsigned long len)
+int
+is_user_addr_valid(struct task_struct *child, unsigned long start, unsigned long len)
 {
 	struct vm_area_struct *vma;
 	struct sram_list_struct *sraml;
@@ -135,6 +136,13 @@ static inline int is_user_addr_valid(struct task_struct *child,
 	if (start >= FIXED_CODE_START && start + len < FIXED_CODE_END)
 		return 0;
 
+#ifdef CONFIG_APP_STACK_L1
+	if (child->mm->context.l1_stack_save)
+		if (start >= (unsigned long)l1_stack_base &&
+			start + len < (unsigned long)l1_stack_base + l1_stack_len)
+			return 0;
+#endif
+
 	return -EIO;
 }
 

arch/blackfin/kernel/sys_bfin.c

@@ -21,6 +21,8 @@
 
 #include <asm/cacheflush.h>
 #include <asm/dma.h>
+#include <asm/cachectl.h>
+#include <asm/ptrace.h>
 
 asmlinkage void *sys_sram_alloc(size_t size, unsigned long flags)
 {
@@ -70,3 +72,16 @@ asmlinkage int sys_bfin_spinlock(int *p)
 
 	return ret;
 }
+
+SYSCALL_DEFINE3(cacheflush, unsigned long, addr, unsigned long, len, int, op)
+{
+	if (is_user_addr_valid(current, addr, len) != 0)
+		return -EINVAL;
+
+	if (op & DCACHE)
+		blackfin_dcache_flush_range(addr, addr + len);
+	if (op & ICACHE)
+		blackfin_icache_flush_range(addr, addr + len);
+
+	return 0;
+}

arch/blackfin/mach-bf518/boards/ezbrd.c

@@ -312,7 +312,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 /* SPI (0) */
 static struct bfin5xx_spi_master bfin_spi0_info = {
-	.num_chipselect = 5,
+	.num_chipselect = 6,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
@@ -347,7 +347,7 @@ static struct platform_device bfin_spi0_device = {
 
 /* SPI (1) */
 static struct bfin5xx_spi_master bfin_spi1_info = {
-	.num_chipselect = 5,
+	.num_chipselect = 6,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
@@ -525,6 +525,14 @@ static struct platform_device bfin_sir1_device = {
 #endif
 #endif
 
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+	.name = "bfin-i2s",
+	.id = CONFIG_SND_BF5XX_SPORT_NUM,
+	/* TODO: add platform data here */
+};
+#endif
+
 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 static struct resource bfin_twi0_resource[] = {
 	[0] = {
@@ -559,6 +567,11 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		.irq = IRQ_PF8,
 	},
 #endif
+#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+	{
+		I2C_BOARD_INFO("ssm2602", 0x1b),
+	},
+#endif
 };
 
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
@@ -736,6 +749,10 @@ static struct platform_device *stamp_devices[] __initdata = {
 	&i2c_bfin_twi_device,
 #endif
 
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+	&bfin_i2s,
+#endif
+
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,

arch/blackfin/mach-bf518/boards/tcm-bf518.c

@@ -291,7 +291,7 @@ static struct platform_device bfin_spi0_device = {
 
 /* SPI (1) */
 static struct bfin5xx_spi_master bfin_spi1_info = {
-	.num_chipselect = 5,
+	.num_chipselect = 6,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };

arch/blackfin/mach-bf518/include/mach/cdefBF51x_base.h

@@ -262,14 +262,14 @@
 #define bfin_write_SPORT0_TX(val)		bfin_write32(SPORT0_TX, val)
 #define bfin_read_SPORT0_RX()			bfin_read32(SPORT0_RX)
 #define bfin_write_SPORT0_RX(val)		bfin_write32(SPORT0_RX, val)
-#define bfin_read_SPORT0_TX32()			bfin_read32(SPORT0_TX32)
-#define bfin_write_SPORT0_TX32(val)		bfin_write32(SPORT0_TX32, val)
-#define bfin_read_SPORT0_RX32()			bfin_read32(SPORT0_RX32)
-#define bfin_write_SPORT0_RX32(val)		bfin_write32(SPORT0_RX32, val)
-#define bfin_read_SPORT0_TX16()			bfin_read16(SPORT0_TX16)
-#define bfin_write_SPORT0_TX16(val)		bfin_write16(SPORT0_TX16, val)
-#define bfin_read_SPORT0_RX16()			bfin_read16(SPORT0_RX16)
-#define bfin_write_SPORT0_RX16(val)		bfin_write16(SPORT0_RX16, val)
+#define bfin_read_SPORT0_TX32()			bfin_read32(SPORT0_TX)
+#define bfin_write_SPORT0_TX32(val)		bfin_write32(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX32()			bfin_read32(SPORT0_RX)
+#define bfin_write_SPORT0_RX32(val)		bfin_write32(SPORT0_RX, val)
+#define bfin_read_SPORT0_TX16()			bfin_read16(SPORT0_TX)
+#define bfin_write_SPORT0_TX16(val)		bfin_write16(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX16()			bfin_read16(SPORT0_RX)
+#define bfin_write_SPORT0_RX16(val)		bfin_write16(SPORT0_RX, val)
 #define bfin_read_SPORT0_RCR1()			bfin_read16(SPORT0_RCR1)
 #define bfin_write_SPORT0_RCR1(val)		bfin_write16(SPORT0_RCR1, val)
 #define bfin_read_SPORT0_RCR2()			bfin_read16(SPORT0_RCR2)
@@ -317,14 +317,14 @@
 #define bfin_write_SPORT1_TX(val)		bfin_write32(SPORT1_TX, val)
 #define bfin_read_SPORT1_RX()			bfin_read32(SPORT1_RX)
 #define bfin_write_SPORT1_RX(val)		bfin_write32(SPORT1_RX, val)
-#define bfin_read_SPORT1_TX32()			bfin_read32(SPORT1_TX32)
-#define bfin_write_SPORT1_TX32(val)		bfin_write32(SPORT1_TX32, val)
-#define bfin_read_SPORT1_RX32()			bfin_read32(SPORT1_RX32)
-#define bfin_write_SPORT1_RX32(val)		bfin_write32(SPORT1_RX32, val)
-#define bfin_read_SPORT1_TX16()			bfin_read16(SPORT1_TX16)
-#define bfin_write_SPORT1_TX16(val)		bfin_write16(SPORT1_TX16, val)
-#define bfin_read_SPORT1_RX16()			bfin_read16(SPORT1_RX16)
-#define bfin_write_SPORT1_RX16(val)		bfin_write16(SPORT1_RX16, val)
+#define bfin_read_SPORT1_TX32()			bfin_read32(SPORT1_TX)
+#define bfin_write_SPORT1_TX32(val)		bfin_write32(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX32()			bfin_read32(SPORT1_RX)
+#define bfin_write_SPORT1_RX32(val)		bfin_write32(SPORT1_RX, val)
+#define bfin_read_SPORT1_TX16()			bfin_read16(SPORT1_TX)
+#define bfin_write_SPORT1_TX16(val)		bfin_write16(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX16()			bfin_read16(SPORT1_RX)
+#define bfin_write_SPORT1_RX16(val)		bfin_write16(SPORT1_RX, val)
 #define bfin_read_SPORT1_RCR1()			bfin_read16(SPORT1_RCR1)
 #define bfin_write_SPORT1_RCR1(val)		bfin_write16(SPORT1_RCR1, val)
 #define bfin_read_SPORT1_RCR2()			bfin_read16(SPORT1_RCR2)

arch/blackfin/mach-bf518/include/mach/defBF51x_base.h

@@ -748,51 +748,6 @@
 #define FFE			0x20		/* Force Framing Error On Transmit	*/
 
 
-/* ***********  SERIAL PERIPHERAL INTERFACE (SPI) MASKS  ****************************/
-/* SPI_CTL Masks																	*/
-#define	TIMOD		0x0003		/* Transfer Initiate Mode							*/
-#define RDBR_CORE	0x0000		/* 		RDBR Read Initiates, IRQ When RDBR Full		*/
-#define	TDBR_CORE	0x0001		/* 		TDBR Write Initiates, IRQ When TDBR Empty	*/
-#define RDBR_DMA	0x0002		/* 		DMA Read, DMA Until FIFO Empty				*/
-#define TDBR_DMA	0x0003		/* 		DMA Write, DMA Until FIFO Full				*/
-#define SZ			0x0004		/* Send Zero (When TDBR Empty, Send Zero/Last*)		*/
-#define GM			0x0008		/* Get More (When RDBR Full, Overwrite/Discard*)	*/
-#define PSSE		0x0010		/* Slave-Select Input Enable						*/
-#define EMISO		0x0020		/* Enable MISO As Output							*/
-#define SIZE		0x0100		/* Size of Words (16/8* Bits)						*/
-#define LSBF		0x0200		/* LSB First										*/
-#define CPHA		0x0400		/* Clock Phase										*/
-#define CPOL		0x0800		/* Clock Polarity									*/
-#define MSTR		0x1000		/* Master/Slave*									*/
-#define WOM			0x2000		/* Write Open Drain Master							*/
-#define SPE			0x4000		/* SPI Enable										*/
-
-/* SPI_FLG Masks																	*/
-#define FLS1		0x0002		/* Enables SPI_FLOUT1 as SPI Slave-Select Output	*/
-#define FLS2		0x0004		/* Enables SPI_FLOUT2 as SPI Slave-Select Output	*/
-#define FLS3		0x0008		/* Enables SPI_FLOUT3 as SPI Slave-Select Output	*/
-#define FLS4		0x0010		/* Enables SPI_FLOUT4 as SPI Slave-Select Output	*/
-#define FLS5		0x0020		/* Enables SPI_FLOUT5 as SPI Slave-Select Output	*/
-#define FLS6		0x0040		/* Enables SPI_FLOUT6 as SPI Slave-Select Output	*/
-#define FLS7		0x0080		/* Enables SPI_FLOUT7 as SPI Slave-Select Output	*/
-#define FLG1		0xFDFF		/* Activates SPI_FLOUT1 							*/
-#define FLG2		0xFBFF		/* Activates SPI_FLOUT2								*/
-#define FLG3		0xF7FF		/* Activates SPI_FLOUT3								*/
-#define FLG4		0xEFFF		/* Activates SPI_FLOUT4								*/
-#define FLG5		0xDFFF		/* Activates SPI_FLOUT5								*/
-#define FLG6		0xBFFF		/* Activates SPI_FLOUT6								*/
-#define FLG7		0x7FFF		/* Activates SPI_FLOUT7								*/
-
-/* SPI_STAT Masks																				*/
-#define SPIF		0x0001		/* SPI Finished (Single-Word Transfer Complete)					*/
-#define MODF		0x0002		/* Mode Fault Error (Another Device Tried To Become Master)		*/
-#define TXE			0x0004		/* Transmission Error (Data Sent With No New Data In TDBR)		*/
-#define TXS			0x0008		/* SPI_TDBR Data Buffer Status (Full/Empty*)					*/
-#define RBSY		0x0010		/* Receive Error (Data Received With RDBR Full)					*/
-#define RXS			0x0020		/* SPI_RDBR Data Buffer Status (Full/Empty*)					*/
-#define TXCOL		0x0040		/* Transmit Collision Error (Corrupt Data May Have Been Sent)	*/
-
-
 /*  ****************  GENERAL PURPOSE TIMER MASKS  **********************/
 /* TIMER_ENABLE Masks													*/
 #define TIMEN0			0x0001		/* Enable Timer 0					*/

arch/blackfin/mach-bf527/boards/Kconfig

@@ -24,4 +24,14 @@ config BFIN526_EZBRD
 	help
 	  BF526-EZBRD/EZKIT Lite board support.
 
+config BFIN527_AD7160EVAL
+	bool "BF527-AD7160-EVAL"
+	help
+	  BF527-AD7160-EVAL board support.
+
+config BFIN527_TLL6527M
+	bool "The Learning Labs TLL6527M"
+	help
+	  TLL6527M V1.0 platform support
+
 endchoice

arch/blackfin/mach-bf527/boards/Makefile

@@ -6,3 +6,5 @@ obj-$(CONFIG_BFIN527_EZKIT)            += ezkit.o
 obj-$(CONFIG_BFIN527_EZKIT_V2)         += ezkit.o
 obj-$(CONFIG_BFIN527_BLUETECHNIX_CM)   += cm_bf527.o
 obj-$(CONFIG_BFIN526_EZBRD)            += ezbrd.o
+obj-$(CONFIG_BFIN527_AD7160EVAL)       += ad7160eval.o
+obj-$(CONFIG_BFIN527_TLL6527M)         += tll6527m.o

arch/blackfin/mach-bf527/boards/ad7160eval.c

@@ -0,0 +1,870 @@
+/*
+ * Copyright 2004-20010 Analog Devices Inc.
+ *                2005 National ICT Australia (NICTA)
+ *                      Aidan Williams <aidan@nicta.com.au>
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <asm/nand.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "ADI BF527-AD7160EVAL";
+
+/*
+ *  Driver needs to know address, irq and flag pin.
+ */
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+	[0] = {
+		.start	= 0xffc03800,
+		.end	= 0xffc03cff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {	/* general IRQ */
+		.start	= IRQ_USB_INT0,
+		.end	= IRQ_USB_INT0,
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+	[2] = {	/* DMA IRQ */
+		.start	= IRQ_USB_DMA,
+		.end	= IRQ_USB_DMA,
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 0,
+	.dyn_fifo	= 0,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 8,
+	.dma_channels	= 8,
+	.gpio_vrsel	= GPIO_PG13,
+	/* Some custom boards need to be active low, just set it to "0"
+	 * if it is the case.
+	 */
+	.gpio_vrsel_active	= 1,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_OTG)
+	.mode		= MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+	.mode		= MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+	.mode		= MUSB_PERIPHERAL,
+#endif
+	.config		= &musb_config,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+	.name		= "musb_hdrc",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &musb_dmamask,
+		.coherent_dma_mask	= 0xffffffff,
+		.platform_data		= &musb_plat,
+	},
+	.num_resources	= ARRAY_SIZE(musb_resources),
+	.resource	= musb_resources,
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+static struct resource bf52x_ra158z_resources[] = {
+	{
+		.start = IRQ_PPI_ERROR,
+		.end = IRQ_PPI_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bf52x_ra158z_device = {
+	.name		= "bfin-ra158z",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(bf52x_ra158z_resources),
+	.resource	= bf52x_ra158z_resources,
+};
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition ad7160eval_partitions[] = {
+	{
+		.name       = "bootloader(nor)",
+		.size       = 0x40000,
+		.offset     = 0,
+	}, {
+		.name       = "linux kernel(nor)",
+		.size       = 0x1C0000,
+		.offset     = MTDPART_OFS_APPEND,
+	}, {
+		.name       = "file system(nor)",
+		.size       = MTDPART_SIZ_FULL,
+		.offset     = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data ad7160eval_flash_data = {
+	.width      = 2,
+	.parts      = ad7160eval_partitions,
+	.nr_parts   = ARRAY_SIZE(ad7160eval_partitions),
+};
+
+static struct resource ad7160eval_flash_resource = {
+	.start = 0x20000000,
+	.end   = 0x203fffff,
+	.flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ad7160eval_flash_device = {
+	.name          = "physmap-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &ad7160eval_flash_data,
+	},
+	.num_resources = 1,
+	.resource      = &ad7160eval_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+static struct mtd_partition partition_info[] = {
+	{
+		.name = "linux kernel(nand)",
+		.offset = 0,
+		.size = 4 * 1024 * 1024,
+	},
+	{
+		.name = "file system(nand)",
+		.offset = MTDPART_OFS_APPEND,
+		.size = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct bf5xx_nand_platform bf5xx_nand_platform = {
+	.data_width = NFC_NWIDTH_8,
+	.partitions = partition_info,
+	.nr_partitions = ARRAY_SIZE(partition_info),
+	.rd_dly = 3,
+	.wr_dly = 3,
+};
+
+static struct resource bf5xx_nand_resources[] = {
+	{
+		.start = NFC_CTL,
+		.end = NFC_DATA_RD + 2,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = CH_NFC,
+		.end = CH_NFC,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bf5xx_nand_device = {
+	.name = "bf5xx-nand",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bf5xx_nand_resources),
+	.resource = bf5xx_nand_resources,
+	.dev = {
+		.platform_data = &bf5xx_nand_platform,
+	},
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+#include <linux/bfin_mac.h>
+static const unsigned short bfin_mac_peripherals[] = P_RMII0;
+
+static struct bfin_phydev_platform_data bfin_phydev_data[] = {
+	{
+		.addr = 1,
+		.irq = IRQ_MAC_PHYINT,
+	},
+};
+
+static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
+	.phydev_number = 1,
+	.phydev_data = bfin_phydev_data,
+	.phy_mode = PHY_INTERFACE_MODE_RMII,
+	.mac_peripherals = bfin_mac_peripherals,
+};
+
+static struct platform_device bfin_mii_bus = {
+	.name = "bfin_mii_bus",
+	.dev = {
+		.platform_data = &bfin_mii_bus_data,
+	}
+};
+
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+	.dev = {
+		.platform_data = &bfin_mii_bus,
+	}
+};
+#endif
+
+
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader(spi)",
+		.size = 0x00040000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "linux kernel(spi)",
+		.size = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p16",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+	.name = "bfin-i2s",
+	.id = CONFIG_SND_BF5XX_SPORT_NUM,
+	/* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+	.name = "bfin-tdm",
+	.id = CONFIG_SND_BF5XX_SPORT_NUM,
+	/* TODO: add platform data here */
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+	{
+		.modalias = "ad183x",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 4,
+		.controller_data = &ad1836_spi_chip_info,
+	},
+#endif
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+	{
+		.modalias = "mmc_spi",
+		.max_speed_hz = 30000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = GPIO_PH3 + MAX_CTRL_CS,
+		.controller_data = &mmc_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+	{
+		.modalias = "spidev",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &spidev_chip_info,
+	},
+#endif
+};
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_DMA,
+	},
+	[2] = {
+		.start = IRQ_SPI,
+		.end   = IRQ_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+	{
+		.start = UART0_THR,
+		.end = UART0_GCTL+2,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART0_ERROR,
+		.end = IRQ_UART0_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_TX,
+		.end = CH_UART0_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX,
+		.flags = IORESOURCE_DMA,
+	},
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+	P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+	.name = "bfin-uart",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_uart0_resources),
+	.resource = bfin_uart0_resources,
+	.dev = {
+		.platform_data = &bfin_uart0_peripherals, /* Passed to driver */
+	},
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+	{
+		.start = UART1_THR,
+		.end = UART1_GCTL+2,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART1_ERROR,
+		.end = IRQ_UART1_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_TX,
+		.end = CH_UART1_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX,
+		.flags = IORESOURCE_DMA,
+	},
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+	{	/* CTS pin */
+		.start = GPIO_PF9,
+		.end = GPIO_PF9,
+		.flags = IORESOURCE_IO,
+	},
+	{	/* RTS pin */
+		.start = GPIO_PF10,
+		.end = GPIO_PF10,
+		.flags = IORESOURCE_IO,
+	},
+#endif
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+	P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart1_resources),
+	.resource = bfin_uart1_resources,
+	.dev = {
+		.platform_data = &bfin_uart1_peripherals, /* Passed to driver */
+	},
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device bfin_sir0_device = {
+	.name = "bfin_sir",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
+	.resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device bfin_sir1_device = {
+	.name = "bfin_sir",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
+	.resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+#include <linux/input/ad7160.h>
+static const struct ad7160_platform_data bfin_ad7160_ts_info = {
+	.sensor_x_res = 854,
+	.sensor_y_res = 480,
+	.pressure = 100,
+	.filter_coef = 3,
+	.coord_pref = AD7160_ORIG_TOP_LEFT,
+	.first_touch_window = 5,
+	.move_window = 3,
+	.event_cabs = AD7160_EMIT_ABS_MT_TRACKING_ID |
+			AD7160_EMIT_ABS_MT_PRESSURE |
+			AD7160_TRACKING_ID_ASCENDING,
+	.finger_act_ctrl = 0x64,
+	.haptic_effect1_ctrl = AD7160_HAPTIC_SLOT_A(60) |
+				AD7160_HAPTIC_SLOT_A_LVL_HIGH |
+				AD7160_HAPTIC_SLOT_B(60) |
+				AD7160_HAPTIC_SLOT_B_LVL_LOW,
+
+	.haptic_effect2_ctrl = AD7160_HAPTIC_SLOT_A(20) |
+				AD7160_HAPTIC_SLOT_A_LVL_HIGH |
+				AD7160_HAPTIC_SLOT_B(80) |
+				AD7160_HAPTIC_SLOT_B_LVL_LOW |
+				AD7160_HAPTIC_SLOT_C(120) |
+				AD7160_HAPTIC_SLOT_C_LVL_HIGH |
+				AD7160_HAPTIC_SLOT_D(30) |
+				AD7160_HAPTIC_SLOT_D_LVL_LOW,
+};
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_TOUCHSCREEN_AD7160) || defined(CONFIG_TOUCHSCREEN_AD7160_MODULE)
+	{
+		I2C_BOARD_INFO("ad7160", 0x33),
+		.irq = IRQ_PH1,
+		.platform_data = (void *)&bfin_ad7160_ts_info,
+	},
+#endif
+};
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+static struct resource bfin_sport0_uart_resources[] = {
+	{
+		.start = SPORT0_TCR1,
+		.end = SPORT0_MRCS3+4,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_SPORT0_RX,
+		.end = IRQ_SPORT0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_SPORT0_ERROR,
+		.end = IRQ_SPORT0_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+unsigned short bfin_sport0_peripherals[] = {
+	P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
+	P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
+};
+
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
+	.resource = bfin_sport0_uart_resources,
+	.dev = {
+		.platform_data = &bfin_sport0_peripherals, /* Passed to driver */
+	},
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+static struct resource bfin_sport1_uart_resources[] = {
+	{
+		.start = SPORT1_TCR1,
+		.end = SPORT1_MRCS3+4,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_SPORT1_RX,
+		.end = IRQ_SPORT1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_SPORT1_ERROR,
+		.end = IRQ_SPORT1_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+unsigned short bfin_sport1_peripherals[] = {
+	P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
+	P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
+	.resource = bfin_sport1_uart_resources,
+	.dev = {
+		.platform_data = &bfin_sport1_peripherals, /* Passed to driver */
+	},
+};
+#endif
+#endif
+
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+#include <asm/bfin_rotary.h>
+
+static struct bfin_rotary_platform_data bfin_rotary_data = {
+	/*.rotary_up_key     = KEY_UP,*/
+	/*.rotary_down_key   = KEY_DOWN,*/
+	.rotary_rel_code   = REL_WHEEL,
+	.rotary_button_key = KEY_ENTER,
+	.debounce	   = 10,	/* 0..17 */
+	.mode		   = ROT_QUAD_ENC | ROT_DEBE,
+};
+
+static struct resource bfin_rotary_resources[] = {
+	{
+		.start = IRQ_CNT,
+		.end = IRQ_CNT,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_rotary_device = {
+	.name		= "bfin-rotary",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(bfin_rotary_resources),
+	.resource	= bfin_rotary_resources,
+	.dev		= {
+		.platform_data = &bfin_rotary_data,
+	},
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] = {
+	VRPAIR(VLEV_100, 400000000),
+	VRPAIR(VLEV_105, 426000000),
+	VRPAIR(VLEV_110, 500000000),
+	VRPAIR(VLEV_115, 533000000),
+	VRPAIR(VLEV_120, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+	.tuple_tab = cclk_vlev_datasheet,
+	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+	.vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+	.name = "bfin dpmc",
+	.dev = {
+		.platform_data = &bfin_dmpc_vreg_data,
+	},
+};
+
+static struct platform_device *stamp_devices[] __initdata = {
+
+	&bfin_dpmc,
+
+#if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
+	&bf5xx_nand_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+	&musb_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mii_bus,
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	&bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	&bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_FB_BFIN_RA158Z) || defined(CONFIG_FB_BFIN_RA158Z_MODULE)
+	&bf52x_ra158z_device,
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+	&bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	&bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+	&bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+	&bfin_sport1_uart_device,
+#endif
+#endif
+
+#if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
+	&bfin_rotary_device,
+#endif
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+	&ad7160eval_flash_device,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+	&bfin_i2s,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+	&bfin_tdm,
+#endif
+};
+
+static int __init ad7160eval_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+	i2c_register_board_info(0, bfin_i2c_board_info,
+				ARRAY_SIZE(bfin_i2c_board_info));
+	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+	return 0;
+}
+
+arch_initcall(ad7160eval_init);
+
+static struct platform_device *ad7160eval_early_devices[] __initdata = {
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	&bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	&bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+	&bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+	&bfin_sport1_uart_device,
+#endif
+#endif
+};
+
+void __init native_machine_early_platform_add_devices(void)
+{
+	printk(KERN_INFO "register early platform devices\n");
+	early_platform_add_devices(ad7160eval_early_devices,
+		ARRAY_SIZE(ad7160eval_early_devices));
+}
+
+void native_machine_restart(char *cmd)
+{
+	/* workaround reboot hang when booting from SPI */
+	if ((bfin_read_SYSCR() & 0x7) == 0x3)
+		bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
+}
+
+void bfin_get_ether_addr(char *addr)
+{
+	/* the MAC is stored in OTP memory page 0xDF */
+	u32 ret;
+	u64 otp_mac;
+	u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
+
+	ret = otp_read(0xDF, 0x00, &otp_mac);
+	if (!(ret & 0x1)) {
+		char *otp_mac_p = (char *)&otp_mac;
+		for (ret = 0; ret < 6; ++ret)
+			addr[ret] = otp_mac_p[5 - ret];
+	}
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);

arch/blackfin/mach-bf527/boards/cm_bf527.c

@@ -342,8 +342,8 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -420,13 +420,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif

arch/blackfin/mach-bf527/boards/ezbrd.c

@@ -137,8 +137,12 @@ static struct platform_device ezbrd_flash_device = {
 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 static struct mtd_partition partition_info[] = {
 	{
-		.name = "linux kernel(nand)",
+		.name = "bootloader(nand)",
 		.offset = 0,
+		.size = 0x40000,
+	}, {
+		.name = "linux kernel(nand)",
+		.offset = MTDPART_OFS_APPEND,
 		.size = 4 * 1024 * 1024,
 	},
 	{

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -222,8 +222,12 @@ static struct platform_device ezkit_flash_device = {
 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 static struct mtd_partition partition_info[] = {
 	{
-		.name = "linux kernel(nand)",
+		.name = "bootloader(nand)",
 		.offset = 0,
+		.size = 0x40000,
+	}, {
+		.name = "linux kernel(nand)",
+		.offset = MTDPART_OFS_APPEND,
 		.size = 4 * 1024 * 1024,
 	},
 	{
@@ -431,8 +435,8 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -547,13 +551,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -929,6 +933,11 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("ssm2602", 0x1b),
 	},
 #endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+	{
+		I2C_BOARD_INFO("ad5252", 0x2f),
+	},
+#endif
 };
 
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)

arch/blackfin/mach-bf527/boards/tll6527m.c

@@ -0,0 +1,986 @@
+/* File:	arch/blackfin/mach-bf527/boards/tll6527m.c
+ * Based on:	arch/blackfin/mach-bf527/boards/ezkit.c
+ * Author:	Ashish Gupta
+ *
+ * Copyright: 2010 - The Learning Labs Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb/musb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <asm/nand.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879) \
+	|| defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+#include <linux/spi/ad7879.h>
+#define LCD_BACKLIGHT_GPIO 0x40
+/* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for
+ * LCD Backlight Enable
+ */
+#endif
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "TLL6527M";
+/*
+ *  Driver needs to know address, irq and flag pin.
+ */
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+static struct resource musb_resources[] = {
+	[0] = {
+		.start	= 0xffc03800,
+		.end	= 0xffc03cff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {	/* general IRQ */
+		.start	= IRQ_USB_INT0,
+		.end	= IRQ_USB_INT0,
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+	[2] = {	/* DMA IRQ */
+		.start	= IRQ_USB_DMA,
+		.end	= IRQ_USB_DMA,
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 0,
+	.dyn_fifo	= 0,
+	.soft_con	= 1,
+	.dma		= 1,
+	.num_eps	= 8,
+	.dma_channels	= 8,
+	/*.gpio_vrsel	= GPIO_PG13,*/
+	/* Some custom boards need to be active low, just set it to "0"
+	 * if it is the case.
+	 */
+	.gpio_vrsel_active	= 1,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_USB_MUSB_OTG)
+	.mode		= MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+	.mode		= MUSB_HOST,
+#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
+	.mode		= MUSB_PERIPHERAL,
+#endif
+	.config		= &musb_config,
+};
+
+static u64 musb_dmamask = ~(u32)0;
+
+static struct platform_device musb_device = {
+	.name		= "musb_hdrc",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &musb_dmamask,
+		.coherent_dma_mask	= 0xffffffff,
+		.platform_data		= &musb_plat,
+	},
+	.num_resources	= ARRAY_SIZE(musb_resources),
+	.resource	= musb_resources,
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#include <asm/bfin-lq035q1.h>
+
+static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
+	.mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
+	.ppi_mode = USE_RGB565_16_BIT_PPI,
+	.use_bl = 1,
+	.gpio_bl = LCD_BACKLIGHT_GPIO,
+};
+
+static struct resource bfin_lq035q1_resources[] = {
+	{
+		.start = IRQ_PPI_ERROR,
+		.end = IRQ_PPI_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_lq035q1_device = {
+	.name		= "bfin-lq035q1",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(bfin_lq035q1_resources),
+	.resource	= bfin_lq035q1_resources,
+	.dev		= {
+		.platform_data = &bfin_lq035q1_data,
+	},
+};
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition tll6527m_partitions[] = {
+	{
+		.name       = "bootloader(nor)",
+		.size       = 0xA0000,
+		.offset     = 0,
+	}, {
+		.name       = "linux kernel(nor)",
+		.size       = 0xD00000,
+		.offset     = MTDPART_OFS_APPEND,
+	}, {
+		.name       = "file system(nor)",
+		.size       = MTDPART_SIZ_FULL,
+		.offset     = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data tll6527m_flash_data = {
+	.width      = 2,
+	.parts      = tll6527m_partitions,
+	.nr_parts   = ARRAY_SIZE(tll6527m_partitions),
+};
+
+static unsigned tll6527m_flash_gpios[] = { GPIO_PG11, GPIO_PH11, GPIO_PH12 };
+
+static struct resource tll6527m_flash_resource[] = {
+	{
+		.name  = "cfi_probe",
+		.start = 0x20000000,
+		.end   = 0x201fffff,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = (unsigned long)tll6527m_flash_gpios,
+		.end   = ARRAY_SIZE(tll6527m_flash_gpios),
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device tll6527m_flash_device = {
+	.name          = "gpio-addr-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &tll6527m_flash_data,
+	},
+	.num_resources = ARRAY_SIZE(tll6527m_flash_resource),
+	.resource      = tll6527m_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+/* An SN74LVC138A 3:8 decoder chip has been used to generate 7 augmented
+ * outputs used as SPI CS lines for all SPI SLAVE devices on TLL6527v1-0.
+ * EXP_GPIO_SPISEL_BASE is the base number for the expanded outputs being
+ * used as SPI CS lines, this should be > MAX_BLACKFIN_GPIOS
+ */
+#include <linux/gpio-decoder.h>
+#define EXP_GPIO_SPISEL_BASE 0x64
+static unsigned gpio_addr_inputs[] = {
+	GPIO_PG1, GPIO_PH9, GPIO_PH10
+};
+
+static struct gpio_decoder_platfrom_data spi_decoded_cs = {
+	.base		= EXP_GPIO_SPISEL_BASE,
+	.input_addrs	= gpio_addr_inputs,
+	.nr_input_addrs = ARRAY_SIZE(gpio_addr_inputs),
+	.default_output	= 0,
+/*	.default_output = (1 << ARRAY_SIZE(gpio_addr_inputs)) - 1 */
+};
+
+static struct platform_device spi_decoded_gpio = {
+	.name	= "gpio-decoder",
+	.id	= 0,
+	.dev	= {
+		.platform_data = &spi_decoded_cs,
+	},
+};
+
+#else
+#define EXP_GPIO_SPISEL_BASE 0x0
+
+#endif
+
+#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#include <linux/input/adxl34x.h>
+static const struct adxl34x_platform_data adxl345_info = {
+	.x_axis_offset = 0,
+	.y_axis_offset = 0,
+	.z_axis_offset = 0,
+	.tap_threshold = 0x31,
+	.tap_duration = 0x10,
+	.tap_latency = 0x60,
+	.tap_window = 0xF0,
+	.tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
+	.act_axis_control = 0xFF,
+	.activity_threshold = 5,
+	.inactivity_threshold = 2,
+	.inactivity_time = 2,
+	.free_fall_threshold = 0x7,
+	.free_fall_time = 0x20,
+	.data_rate = 0x8,
+	.data_range = ADXL_FULL_RES,
+
+	.ev_type = EV_ABS,
+	.ev_code_x = ABS_X,		/* EV_REL */
+	.ev_code_y = ABS_Y,		/* EV_REL */
+	.ev_code_z = ABS_Z,		/* EV_REL */
+
+	.ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
+
+/*	.ev_code_ff = KEY_F,*/		/* EV_KEY */
+	.ev_code_act_inactivity = KEY_A,	/* EV_KEY */
+	.use_int2 = 1,
+	.power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
+	.fifo_mode = ADXL_FIFO_STREAM,
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+	.name = "bfin_mii_bus",
+};
+
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+	.dev.platform_data = &bfin_mii_bus,
+};
+#endif
+
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader(spi)",
+		.size = 0x00040000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "linux kernel(spi)",
+		.size = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p16",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) \
+	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+/*
+ * tll6527m V1.0 does not support native spi slave selects
+ * hence DMA mode will not be useful since the ADC needs
+ * CS to toggle for each sample and cs_change_per_word
+ * seems to be removed from spi_bfin5xx.c
+ */
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879) \
+	|| defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
+static const struct ad7879_platform_data bfin_ad7879_ts_info = {
+	.model			= 7879,	/* Model = AD7879 */
+	.x_plate_ohms		= 620,	/* 620 Ohm from the touch datasheet */
+	.pressure_max		= 10000,
+	.pressure_min		= 0,
+	.first_conversion_delay = 3,
+				/* wait 512us before do a first conversion */
+	.acquisition_time	= 1,	/* 4us acquisition time per sample */
+	.median			= 2,	/* do 8 measurements */
+	.averaging		= 1,
+				/* take the average of 4 middle samples */
+	.pen_down_acc_interval	= 255,	/* 9.4 ms */
+	.gpio_export		= 1,	/* configure AUX as GPIO output*/
+	.gpio_base		= LCD_BACKLIGHT_GPIO,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
+	|| defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+	.name = "bfin-i2s",
+	.id = CONFIG_SND_BF5XX_SPORT_NUM,
+	/* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
+	.enable_dma	= 0,
+	.bits_per_word	= 8,
+};
+#endif
+
+#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+static struct bfin5xx_spi_chip spi_mcp23s08_sys_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+
+static struct bfin5xx_spi_chip spi_mcp23s08_usr_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+
+#include <linux/spi/mcp23s08.h>
+static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
+	.chip[0].is_present = true,
+	.base = 0x30,
+};
+static const struct mcp23s08_platform_data bfin_mcp23s08_usr_gpio_info = {
+	.chip[2].is_present = true,
+	.base = 0x38,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,
+				/* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
+		/* Can be connected to TLL6527M GPIO connector */
+		/* Either SPI_ADC or M25P80 FLASH can be installed at a time */
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC)
+	|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
+	{
+		.modalias = "bfin_spi_adc",
+				/* Name of spi_driver for this device */
+		.max_speed_hz = 10000000,
+				/* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
+		 /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+		.mode = SPI_MODE_0,
+	},
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+	{
+		.modalias = "mmc_spi",
+/*
+ * TLL6527M V1.0 does not support SD Card at SPI Clock > 10 MHz due to
+ * SPI buffer limitations
+ */
+		.max_speed_hz = 10000000,
+					/* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x05 + MAX_CTRL_CS,
+		.controller_data = &mmc_spi_chip_info,
+		.mode = SPI_MODE_0,
+	},
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
+	|| defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
+	{
+		.modalias = "ad7879",
+		.platform_data = &bfin_ad7879_ts_info,
+		.irq = IRQ_PH14,
+		.max_speed_hz = 5000000,
+					/* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x07 + MAX_CTRL_CS,
+		.controller_data = &spi_ad7879_chip_info,
+		.mode = SPI_CPHA | SPI_CPOL,
+	},
+#endif
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+	{
+		.modalias = "spidev",
+		.max_speed_hz = 10000000,
+		/* TLL6527Mv1-0 supports max spi clock (SCK) speed = 10 MHz */
+		.bus_num = 0,
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x03 + MAX_CTRL_CS,
+		.mode = SPI_CPHA | SPI_CPOL,
+		.controller_data = &spidev_chip_info,
+	},
+#endif
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+	{
+		.modalias = "bfin-lq035q1-spi",
+		.max_speed_hz = 20000000,
+		.bus_num = 0,
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x06 + MAX_CTRL_CS,
+		.controller_data = &lq035q1_spi_chip_info,
+		.mode = SPI_CPHA | SPI_CPOL,
+	},
+#endif
+#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
+	{
+		.modalias = "mcp23s08",
+		.platform_data = &bfin_mcp23s08_sys_gpio_info,
+		.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x01 + MAX_CTRL_CS,
+		.controller_data = &spi_mcp23s08_sys_chip_info,
+		.mode = SPI_CPHA | SPI_CPOL,
+	},
+	{
+		.modalias = "mcp23s08",
+		.platform_data = &bfin_mcp23s08_usr_gpio_info,
+		.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = EXP_GPIO_SPISEL_BASE + 0x02 + MAX_CTRL_CS,
+		.controller_data = &spi_mcp23s08_usr_chip_info,
+		.mode = SPI_CPHA | SPI_CPOL,
+	},
+#endif
+};
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = EXP_GPIO_SPISEL_BASE + 8 + MAX_CTRL_CS,
+	/* EXP_GPIO_SPISEL_BASE will be > MAX_BLACKFIN_GPIOS */
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_DMA,
+	},
+	[2] = {
+		.start = IRQ_SPI,
+		.end   = IRQ_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+	{
+		.start = UART0_THR,
+		.end = UART0_GCTL+2,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART0_ERROR,
+		.end = IRQ_UART0_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_TX,
+		.end = CH_UART0_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX,
+		.flags = IORESOURCE_DMA,
+	},
+};
+
+unsigned short bfin_uart0_peripherals[] = {
+	P_UART0_TX, P_UART0_RX, 0
+};
+
+static struct platform_device bfin_uart0_device = {
+	.name = "bfin-uart",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_uart0_resources),
+	.resource = bfin_uart0_resources,
+	.dev = {
+		.platform_data = &bfin_uart0_peripherals,
+					/* Passed to driver */
+	},
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+	{
+		.start = UART1_THR,
+		.end = UART1_GCTL+2,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART1_ERROR,
+		.end = IRQ_UART1_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_TX,
+		.end = CH_UART1_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX,
+		.flags = IORESOURCE_DMA,
+	},
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+	{	/* CTS pin */
+		.start = GPIO_PF9,
+		.end = GPIO_PF9,
+		.flags = IORESOURCE_IO,
+	},
+	{	/* RTS pin */
+		.start = GPIO_PF10,
+		.end = GPIO_PF10,
+		.flags = IORESOURCE_IO,
+	},
+#endif
+};
+
+unsigned short bfin_uart1_peripherals[] = {
+	P_UART1_TX, P_UART1_RX, 0
+};
+
+static struct platform_device bfin_uart1_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart1_resources),
+	.resource = bfin_uart1_resources,
+	.dev = {
+		.platform_data = &bfin_uart1_peripherals,
+						/* Passed to driver */
+	},
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device bfin_sir0_device = {
+	.name = "bfin_sir",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
+	.resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device bfin_sir1_device = {
+	.name = "bfin_sir",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
+	.resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+	{
+		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
+	},
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+	{
+		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
+	},
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) \
+	|| defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+	{
+		I2C_BOARD_INFO("ad7879", 0x2C),
+		.irq = IRQ_PH14,
+		.platform_data = (void *)&bfin_ad7879_ts_info,
+	},
+#endif
+#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
+	{
+		I2C_BOARD_INFO("ssm2602", 0x1b),
+	},
+#endif
+	{
+		I2C_BOARD_INFO("adm1192", 0x2e),
+	},
+
+	{
+		I2C_BOARD_INFO("ltc3576", 0x09),
+	},
+#if defined(CONFIG_INPUT_ADXL34X_I2C) \
+	|| defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+	{
+		I2C_BOARD_INFO("adxl34x", 0x53),
+		.irq = IRQ_PH13,
+		.platform_data = (void *)&adxl345_info,
+	},
+#endif
+};
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) \
+	|| defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+static struct resource bfin_sport0_uart_resources[] = {
+	{
+		.start = SPORT0_TCR1,
+		.end = SPORT0_MRCS3+4,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_SPORT0_RX,
+		.end = IRQ_SPORT0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_SPORT0_ERROR,
+		.end = IRQ_SPORT0_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+unsigned short bfin_sport0_peripherals[] = {
+	P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
+	P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
+};
+
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
+	.resource = bfin_sport0_uart_resources,
+	.dev = {
+		.platform_data = &bfin_sport0_peripherals,
+		/* Passed to driver */
+	},
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+static struct resource bfin_sport1_uart_resources[] = {
+	{
+		.start = SPORT1_TCR1,
+		.end = SPORT1_MRCS3+4,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_SPORT1_RX,
+		.end = IRQ_SPORT1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_SPORT1_ERROR,
+		.end = IRQ_SPORT1_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+unsigned short bfin_sport1_peripherals[] = {
+	P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
+	P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
+	.resource = bfin_sport1_uart_resources,
+	.dev = {
+		.platform_data = &bfin_sport1_peripherals,
+		/* Passed to driver */
+	},
+};
+#endif
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] = {
+	VRPAIR(VLEV_100, 400000000),
+	VRPAIR(VLEV_105, 426000000),
+	VRPAIR(VLEV_110, 500000000),
+	VRPAIR(VLEV_115, 533000000),
+	VRPAIR(VLEV_120, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+	.tuple_tab = cclk_vlev_datasheet,
+	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+	.vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+	.name = "bfin dpmc",
+	.dev = {
+		.platform_data = &bfin_dmpc_vreg_data,
+	},
+};
+
+static struct platform_device *tll6527m_devices[] __initdata = {
+
+	&bfin_dpmc,
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
+	&musb_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mii_bus,
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+	&bfin_lq035q1_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	&bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	&bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+	&bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	&bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) \
+	|| defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+	&bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+	&bfin_sport1_uart_device,
+#endif
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+	&tll6527m_flash_device,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+	&bfin_i2s,
+#endif
+
+#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
+	&spi_decoded_gpio,
+#endif
+};
+
+static int __init tll6527m_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+	i2c_register_board_info(0, bfin_i2c_board_info,
+				ARRAY_SIZE(bfin_i2c_board_info));
+	platform_add_devices(tll6527m_devices, ARRAY_SIZE(tll6527m_devices));
+	spi_register_board_info(bfin_spi_board_info,
+				ARRAY_SIZE(bfin_spi_board_info));
+	return 0;
+}
+
+arch_initcall(tll6527m_init);
+
+static struct platform_device *tll6527m_early_devices[] __initdata = {
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	&bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	&bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
+#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
+	&bfin_sport0_uart_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
+	&bfin_sport1_uart_device,
+#endif
+#endif
+};
+
+void __init native_machine_early_platform_add_devices(void)
+{
+	printk(KERN_INFO "register early platform devices\n");
+	early_platform_add_devices(tll6527m_early_devices,
+		ARRAY_SIZE(tll6527m_early_devices));
+}
+
+void native_machine_restart(char *cmd)
+{
+	/* workaround reboot hang when booting from SPI */
+	if ((bfin_read_SYSCR() & 0x7) == 0x3)
+		bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
+}
+
+void bfin_get_ether_addr(char *addr)
+{
+	/* the MAC is stored in OTP memory page 0xDF */
+	u32 ret;
+	u64 otp_mac;
+	u32 (*otp_read)(u32 page, u32 flags,
+			u64 *page_content) = (void *)0xEF00001A;
+
+	ret = otp_read(0xDF, 0x00, &otp_mac);
+	if (!(ret & 0x1)) {
+		char *otp_mac_p = (char *)&otp_mac;
+		for (ret = 0; ret < 6; ++ret)
+			addr[ret] = otp_mac_p[5 - ret];
+	}
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);

arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h

@@ -279,14 +279,14 @@
 #define bfin_write_SPORT0_TX(val)		bfin_write32(SPORT0_TX, val)
 #define bfin_read_SPORT0_RX()			bfin_read32(SPORT0_RX)
 #define bfin_write_SPORT0_RX(val)		bfin_write32(SPORT0_RX, val)
-#define bfin_read_SPORT0_TX32()			bfin_read32(SPORT0_TX32)
-#define bfin_write_SPORT0_TX32(val)		bfin_write32(SPORT0_TX32, val)
-#define bfin_read_SPORT0_RX32()			bfin_read32(SPORT0_RX32)
-#define bfin_write_SPORT0_RX32(val)		bfin_write32(SPORT0_RX32, val)
-#define bfin_read_SPORT0_TX16()			bfin_read16(SPORT0_TX16)
-#define bfin_write_SPORT0_TX16(val)		bfin_write16(SPORT0_TX16, val)
-#define bfin_read_SPORT0_RX16()			bfin_read16(SPORT0_RX16)
-#define bfin_write_SPORT0_RX16(val)		bfin_write16(SPORT0_RX16, val)
+#define bfin_read_SPORT0_TX32()			bfin_read32(SPORT0_TX)
+#define bfin_write_SPORT0_TX32(val)		bfin_write32(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX32()			bfin_read32(SPORT0_RX)
+#define bfin_write_SPORT0_RX32(val)		bfin_write32(SPORT0_RX, val)
+#define bfin_read_SPORT0_TX16()			bfin_read16(SPORT0_TX)
+#define bfin_write_SPORT0_TX16(val)		bfin_write16(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX16()			bfin_read16(SPORT0_RX)
+#define bfin_write_SPORT0_RX16(val)		bfin_write16(SPORT0_RX, val)
 #define bfin_read_SPORT0_RCR1()			bfin_read16(SPORT0_RCR1)
 #define bfin_write_SPORT0_RCR1(val)		bfin_write16(SPORT0_RCR1, val)
 #define bfin_read_SPORT0_RCR2()			bfin_read16(SPORT0_RCR2)
@@ -334,14 +334,14 @@
 #define bfin_write_SPORT1_TX(val)		bfin_write32(SPORT1_TX, val)
 #define bfin_read_SPORT1_RX()			bfin_read32(SPORT1_RX)
 #define bfin_write_SPORT1_RX(val)		bfin_write32(SPORT1_RX, val)
-#define bfin_read_SPORT1_TX32()			bfin_read32(SPORT1_TX32)
-#define bfin_write_SPORT1_TX32(val)		bfin_write32(SPORT1_TX32, val)
-#define bfin_read_SPORT1_RX32()			bfin_read32(SPORT1_RX32)
-#define bfin_write_SPORT1_RX32(val)		bfin_write32(SPORT1_RX32, val)
-#define bfin_read_SPORT1_TX16()			bfin_read16(SPORT1_TX16)
-#define bfin_write_SPORT1_TX16(val)		bfin_write16(SPORT1_TX16, val)
-#define bfin_read_SPORT1_RX16()			bfin_read16(SPORT1_RX16)
-#define bfin_write_SPORT1_RX16(val)		bfin_write16(SPORT1_RX16, val)
+#define bfin_read_SPORT1_TX32()			bfin_read32(SPORT1_TX)
+#define bfin_write_SPORT1_TX32(val)		bfin_write32(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX32()			bfin_read32(SPORT1_RX)
+#define bfin_write_SPORT1_RX32(val)		bfin_write32(SPORT1_RX, val)
+#define bfin_read_SPORT1_TX16()			bfin_read16(SPORT1_TX)
+#define bfin_write_SPORT1_TX16(val)		bfin_write16(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX16()			bfin_read16(SPORT1_RX)
+#define bfin_write_SPORT1_RX16(val)		bfin_write16(SPORT1_RX, val)
 #define bfin_read_SPORT1_RCR1()			bfin_read16(SPORT1_RCR1)
 #define bfin_write_SPORT1_RCR1(val)		bfin_write16(SPORT1_RCR1, val)
 #define bfin_read_SPORT1_RCR2()			bfin_read16(SPORT1_RCR2)

arch/blackfin/mach-bf527/include/mach/defBF52x_base.h

@@ -749,51 +749,6 @@
 #define FFE			0x20		/* Force Framing Error On Transmit	*/
 
 
-/* ***********  SERIAL PERIPHERAL INTERFACE (SPI) MASKS  ****************************/
-/* SPI_CTL Masks																	*/
-#define	TIMOD		0x0003		/* Transfer Initiate Mode							*/
-#define RDBR_CORE	0x0000		/* 		RDBR Read Initiates, IRQ When RDBR Full		*/
-#define	TDBR_CORE	0x0001		/* 		TDBR Write Initiates, IRQ When TDBR Empty	*/
-#define RDBR_DMA	0x0002		/* 		DMA Read, DMA Until FIFO Empty				*/
-#define TDBR_DMA	0x0003		/* 		DMA Write, DMA Until FIFO Full				*/
-#define SZ			0x0004		/* Send Zero (When TDBR Empty, Send Zero/Last*)		*/
-#define GM			0x0008		/* Get More (When RDBR Full, Overwrite/Discard*)	*/
-#define PSSE		0x0010		/* Slave-Select Input Enable						*/
-#define EMISO		0x0020		/* Enable MISO As Output							*/
-#define SIZE		0x0100		/* Size of Words (16/8* Bits)						*/
-#define LSBF		0x0200		/* LSB First										*/
-#define CPHA		0x0400		/* Clock Phase										*/
-#define CPOL		0x0800		/* Clock Polarity									*/
-#define MSTR		0x1000		/* Master/Slave*									*/
-#define WOM			0x2000		/* Write Open Drain Master							*/
-#define SPE			0x4000		/* SPI Enable										*/
-
-/* SPI_FLG Masks																	*/
-#define FLS1		0x0002		/* Enables SPI_FLOUT1 as SPI Slave-Select Output	*/
-#define FLS2		0x0004		/* Enables SPI_FLOUT2 as SPI Slave-Select Output	*/
-#define FLS3		0x0008		/* Enables SPI_FLOUT3 as SPI Slave-Select Output	*/
-#define FLS4		0x0010		/* Enables SPI_FLOUT4 as SPI Slave-Select Output	*/
-#define FLS5		0x0020		/* Enables SPI_FLOUT5 as SPI Slave-Select Output	*/
-#define FLS6		0x0040		/* Enables SPI_FLOUT6 as SPI Slave-Select Output	*/
-#define FLS7		0x0080		/* Enables SPI_FLOUT7 as SPI Slave-Select Output	*/
-#define FLG1		0xFDFF		/* Activates SPI_FLOUT1 							*/
-#define FLG2		0xFBFF		/* Activates SPI_FLOUT2								*/
-#define FLG3		0xF7FF		/* Activates SPI_FLOUT3								*/
-#define FLG4		0xEFFF		/* Activates SPI_FLOUT4								*/
-#define FLG5		0xDFFF		/* Activates SPI_FLOUT5								*/
-#define FLG6		0xBFFF		/* Activates SPI_FLOUT6								*/
-#define FLG7		0x7FFF		/* Activates SPI_FLOUT7								*/
-
-/* SPI_STAT Masks																				*/
-#define SPIF		0x0001		/* SPI Finished (Single-Word Transfer Complete)					*/
-#define MODF		0x0002		/* Mode Fault Error (Another Device Tried To Become Master)		*/
-#define TXE			0x0004		/* Transmission Error (Data Sent With No New Data In TDBR)		*/
-#define TXS			0x0008		/* SPI_TDBR Data Buffer Status (Full/Empty*)					*/
-#define RBSY		0x0010		/* Receive Error (Data Received With RDBR Full)					*/
-#define RXS			0x0020		/* SPI_RDBR Data Buffer Status (Full/Empty*)					*/
-#define TXCOL		0x0040		/* Transmit Collision Error (Corrupt Data May Have Been Sent)	*/
-
-
 /*  ****************  GENERAL PURPOSE TIMER MASKS  **********************/
 /* TIMER_ENABLE Masks													*/
 #define TIMEN0			0x0001		/* Enable Timer 0					*/

arch/blackfin/mach-bf533/boards/H8606.c

@@ -171,7 +171,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -206,12 +206,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 16,
 		.bus_num = 1,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -347,6 +347,7 @@ static struct plat_serial8250_port serial8250_platform_data [] = {
 		.membase = (void *)0x20200000,
 		.mapbase = 0x20200000,
 		.irq = IRQ_PF8,
+		.irqflags = IRQF_TRIGGER_HIGH,
 		.flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE,
 		.iotype = UPIO_MEM,
 		.regshift = 1,
@@ -355,6 +356,7 @@ static struct plat_serial8250_port serial8250_platform_data [] = {
 		.membase = (void *)0x20200010,
 		.mapbase = 0x20200010,
 		.irq = IRQ_PF8,
+		.irqflags = IRQF_TRIGGER_HIGH,
 		.flags = UPF_BOOT_AUTOCONF | UART_CONFIG_TYPE,
 		.iotype = UPIO_MEM,
 		.regshift = 1,

arch/blackfin/mach-bf533/boards/blackstamp.c

@@ -368,8 +368,8 @@ static struct platform_device bfin_device_gpiokeys = {
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
-	.sda_pin		= 8,
-	.scl_pin		= 9,
+	.sda_pin		= GPIO_PF8,
+	.scl_pin		= GPIO_PF9,
 	.sda_is_open_drain	= 0,
 	.scl_is_open_drain	= 0,
 	.udelay			= 40,

arch/blackfin/mach-bf533/boards/cm_bf533.c

@@ -71,7 +71,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -110,12 +110,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -400,7 +400,7 @@ static struct resource isp1362_hcd_resources[] = {
 	}, {
 		.start = IRQ_PF4,
 		.end = IRQ_PF4,
-		.flags = IORESOURCE_IRQ,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 

arch/blackfin/mach-bf533/boards/ezkit.c

@@ -222,7 +222,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -261,12 +261,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -422,8 +422,8 @@ static struct platform_device bfin_device_gpiokeys = {
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
-	.sda_pin		= 1,
-	.scl_pin		= 0,
+	.sda_pin		= GPIO_PF1,
+	.scl_pin		= GPIO_PF0,
 	.sda_is_open_drain	= 0,
 	.scl_is_open_drain	= 0,
 	.udelay			= 40,

arch/blackfin/mach-bf533/boards/ip0x.c

@@ -232,7 +232,7 @@ static struct resource isp1362_hcd_resources[] = {
 	},{
 		.start = IRQ_PF11,
 		.end   = IRQ_PF11,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 

arch/blackfin/mach-bf533/boards/stamp.c

@@ -185,7 +185,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -252,13 +252,15 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
+		.platform_data = "ad1836", /* only includes chip name for the moment */
 		.controller_data = &ad1836_spi_chip_info,
+		.mode = SPI_MODE_3,
 	},
 #endif
 
@@ -495,8 +497,8 @@ static struct platform_device bfin_device_gpiokeys = {
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
-	.sda_pin		= 2,
-	.scl_pin		= 3,
+	.sda_pin		= GPIO_PF2,
+	.scl_pin		= GPIO_PF3,
 	.sda_is_open_drain	= 0,
 	.scl_is_open_drain	= 0,
 	.udelay			= 40,
@@ -534,6 +536,11 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+	{
+		I2C_BOARD_INFO("ad5252", 0x2f),
+	},
+#endif
 };
 
 static const unsigned int cclk_vlev_datasheet[] =

arch/blackfin/mach-bf533/include/mach/defBF532.h

@@ -681,76 +681,6 @@
 #define PF14_P        14
 #define PF15_P        15
 
-/* ***********  SERIAL PERIPHERAL INTERFACE (SPI) MASKS  **************** */
-
-/* SPI_CTL Masks */
-#define TIMOD                  0x00000003	/* Transfer initiation mode and interrupt generation */
-#define RDBR_CORE	0x0000		/* 		RDBR Read Initiates, IRQ When RDBR Full		*/
-#define	TDBR_CORE	0x0001		/* 		TDBR Write Initiates, IRQ When TDBR Empty	*/
-#define RDBR_DMA	0x0002		/* 		DMA Read, DMA Until FIFO Empty				*/
-#define TDBR_DMA	0x0003		/* 		DMA Write, DMA Until FIFO Full				*/
-#define SZ                     0x00000004	/* Send Zero (=0) or last (=1) word when TDBR empty. */
-#define GM                     0x00000008	/* When RDBR full, get more (=1) data or discard (=0) incoming Data */
-#define PSSE                   0x00000010	/* Enable (=1) Slave-Select input for Master. */
-#define EMISO                  0x00000020	/* Enable (=1) MISO pin as an output. */
-#define SIZE                   0x00000100	/* Word length (0 => 8 bits, 1 => 16 bits) */
-#define LSBF                   0x00000200	/* Data format (0 => MSB sent/received first 1 => LSB sent/received first) */
-#define CPHA                   0x00000400	/* Clock phase (0 => SPICLK starts toggling in middle of xfer, 1 => SPICLK toggles at the beginning of xfer. */
-#define CPOL                   0x00000800	/* Clock polarity (0 => active-high, 1 => active-low) */
-#define MSTR                   0x00001000	/* Configures SPI as master (=1) or slave (=0) */
-#define WOM                    0x00002000	/* Open drain (=1) data output enable (for MOSI and MISO) */
-#define SPE                    0x00004000	/* SPI module enable (=1), disable (=0) */
-
-/* SPI_FLG Masks */
-#define FLS1                   0x00000002	/* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2                   0x00000004	/* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3                   0x00000008	/* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4                   0x00000010	/* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5                   0x00000020	/* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6                   0x00000040	/* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7                   0x00000080	/* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1                   0x00000200	/* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select  */
-#define FLG2                   0x00000400	/* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3                   0x00000800	/* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select  */
-#define FLG4                   0x00001000	/* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select  */
-#define FLG5                   0x00002000	/* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select  */
-#define FLG6                   0x00004000	/* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select  */
-#define FLG7                   0x00008000	/* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_FLG Bit Positions */
-#define FLS1_P                 0x00000001	/* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2_P                 0x00000002	/* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3_P                 0x00000003	/* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4_P                 0x00000004	/* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5_P                 0x00000005	/* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6_P                 0x00000006	/* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7_P                 0x00000007	/* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1_P                 0x00000009	/* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select  */
-#define FLG2_P                 0x0000000A	/* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3_P                 0x0000000B	/* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select  */
-#define FLG4_P                 0x0000000C	/* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select  */
-#define FLG5_P                 0x0000000D	/* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select  */
-#define FLG6_P                 0x0000000E	/* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select  */
-#define FLG7_P                 0x0000000F	/* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_STAT Masks */
-#define SPIF                   0x00000001	/* Set (=1) when SPI single-word transfer complete */
-#define MODF                   0x00000002	/* Set (=1) in a master device when some other device tries to become master */
-#define TXE                    0x00000004	/* Set (=1) when transmission occurs with no new data in SPI_TDBR */
-#define TXS                    0x00000008	/* SPI_TDBR Data Buffer Status (0=Empty, 1=Full) */
-#define RBSY                   0x00000010	/* Set (=1) when data is received with RDBR full */
-#define RXS                    0x00000020	/* SPI_RDBR Data Buffer Status (0=Empty, 1=Full)  */
-#define TXCOL                  0x00000040	/* When set (=1), corrupt data may have been transmitted  */
-
-/* SPIx_FLG Masks																	*/
-#define FLG1E	0xFDFF		/* Activates SPI_FLOUT1 							*/
-#define FLG2E	0xFBFF		/* Activates SPI_FLOUT2								*/
-#define FLG3E	0xF7FF		/* Activates SPI_FLOUT3								*/
-#define FLG4E	0xEFFF		/* Activates SPI_FLOUT4								*/
-#define FLG5E	0xDFFF		/* Activates SPI_FLOUT5								*/
-#define FLG6E	0xBFFF		/* Activates SPI_FLOUT6								*/
-#define FLG7E	0x7FFF		/* Activates SPI_FLOUT7								*/
-
 /* *********************  ASYNCHRONOUS MEMORY CONTROLLER MASKS  ************* */
 
 /* AMGCTL Masks */

arch/blackfin/mach-bf537/Kconfig

@@ -14,8 +14,8 @@ config IRQ_DMA_ERROR
 	int "IRQ_DMA_ERROR Generic"
 	default 7
 config IRQ_ERROR
-	int "IRQ_ERROR: CAN MAC SPORT0 SPORT1 SPI UART0 UART1"
-	default 7
+	int "IRQ_ERROR: PPI CAN MAC SPORT0 SPORT1 SPI UART0 UART1"
+	default 11
 config IRQ_RTC
 	int "IRQ_RTC"
 	default 8

arch/blackfin/mach-bf537/boards/cm_bf537e.c

@@ -73,7 +73,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -112,12 +112,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -229,7 +229,7 @@ static struct resource isp1362_hcd_resources[] = {
 	}, {
 		.start = IRQ_PG15,
 		.end = IRQ_PG15,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 

arch/blackfin/mach-bf537/boards/cm_bf537u.c

@@ -74,7 +74,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -113,12 +113,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -230,7 +230,7 @@ static struct resource isp1362_hcd_resources[] = {
 	}, {
 		.start = IRQ_PG15,
 		.end = IRQ_PG15,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 

arch/blackfin/mach-bf537/boards/pnav10.c

@@ -175,8 +175,8 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -238,13 +238,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif

arch/blackfin/mach-bf537/boards/stamp.c

@@ -35,12 +35,10 @@
 #include <asm/reboot.h>
 #include <asm/portmux.h>
 #include <asm/dpmc.h>
-#ifdef CONFIG_REGULATOR_ADP_SWITCH
-#include <linux/regulator/adp_switch.h>
-#endif
-#ifdef CONFIG_REGULATOR_AD5398
-#include <linux/regulator/ad5398.h>
+#ifdef CONFIG_REGULATOR_FIXED_VOLTAGE
+#include <linux/regulator/fixed.h>
 #endif
+#include <linux/regulator/machine.h>
 #include <linux/regulator/consumer.h>
 #include <linux/regulator/userspace-consumer.h>
 
@@ -264,7 +262,7 @@ static struct resource isp1362_hcd_resources[] = {
 	}, {
 		.start = IRQ_PF3,
 		.end = IRQ_PF3,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 
@@ -418,7 +416,7 @@ static struct platform_nand_data bfin_plat_nand_data = {
 static struct resource bfin_plat_nand_resources = {
 	.start = 0x20212000,
 	.end   = 0x20212000 + (1 << MAX(BFIN_NAND_PLAT_CLE, BFIN_NAND_PLAT_ALE)),
-	.flags = IORESOURCE_IO,
+	.flags = IORESOURCE_MEM,
 };
 
 static struct platform_device bfin_async_nand_device = {
@@ -545,6 +543,14 @@ static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
 };
 #endif
 
+#if defined(CONFIG_SND_BF5XX_SOC_ADAV80X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_ADAV80X_MODULE)
+static struct bfin5xx_spi_chip adav801_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 #include <linux/input/ad714x.h>
 static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
@@ -693,6 +699,65 @@ static struct bfin5xx_spi_chip ad2s1210_spi_chip_info = {
 };
 #endif
 
+#if defined(CONFIG_AD7314) || defined(CONFIG_AD7314_MODULE)
+static struct bfin5xx_spi_chip ad7314_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+static unsigned short ad7816_platform_data[] = {
+	GPIO_PF4, /* rdwr_pin */
+	GPIO_PF5, /* convert_pin */
+	GPIO_PF7, /* busy_pin */
+	0,
+};
+
+static struct bfin5xx_spi_chip ad7816_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+static unsigned long adt7310_platform_data[3] = {
+/* INT bound temperature alarm event. line 1 */
+	IRQ_PG4, IRQF_TRIGGER_LOW,
+/* CT bound temperature alarm event irq_flags. line 0 */
+	IRQF_TRIGGER_LOW,
+};
+
+static struct bfin5xx_spi_chip adt7310_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+static unsigned short ad7298_platform_data[] = {
+	GPIO_PF7, /* busy_pin */
+	0,
+};
+
+static struct bfin5xx_spi_chip ad7298_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+static unsigned long adt7316_spi_data[2] = {
+	IRQF_TRIGGER_LOW, /* interrupt flags */
+	GPIO_PF7, /* ldac_pin, 0 means DAC/LDAC registers control DAC update */
+};
+
+static struct bfin5xx_spi_chip adt7316_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 #define MMC_SPI_CARD_DETECT_INT IRQ_PF5
 
@@ -824,14 +889,12 @@ static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
 	.enable_dma	= 1,
 	.bits_per_word	= 8,
-	.cs_gpio = GPIO_PF10,
 };
 #endif
 
 #if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
 static struct bfin5xx_spi_chip adf7021_spi_chip_info = {
 	.bits_per_word = 16,
-	.cs_gpio = GPIO_PF10,
 };
 
 #include <linux/spi/adf702x.h>
@@ -938,6 +1001,13 @@ static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
 };
 #endif
 
+#if defined(CONFIG_AD7476) || defined(CONFIG_AD7476_MODULE)
+static struct bfin5xx_spi_chip spi_ad7476_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) \
 	|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -982,7 +1052,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
+		.chip_select = 4,
 		.platform_data = "ad1836", /* only includes chip name for the moment */
 		.controller_data = &ad1836_spi_chip_info,
 		.mode = SPI_MODE_3,
@@ -1000,6 +1070,17 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
+#if defined(CONFIG_SND_BF5XX_SOC_ADAV80X) || defined(CONFIG_SND_BF5XX_SOC_ADAV80X_MODULE)
+	{
+		.modalias = "adav80x",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &adav801_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 	{
 		.modalias = "ad714x_captouch",
@@ -1018,6 +1099,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.modalias = "ad2s90",
 		.bus_num = 0,
 		.chip_select = 3,            /* change it for your board */
+		.mode = SPI_MODE_3,
 		.platform_data = NULL,
 		.controller_data = &ad2s90_spi_chip_info,
 	},
@@ -1044,6 +1126,67 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
+#if defined(CONFIG_AD7314) || defined(CONFIG_AD7314_MODULE)
+	{
+		.modalias = "ad7314",
+		.max_speed_hz = 1000000,
+		.bus_num = 0,
+		.chip_select = 4,            /* CS, change it for your board */
+		.controller_data = &ad7314_spi_chip_info,
+		.mode = SPI_MODE_1,
+	},
+#endif
+
+#if defined(CONFIG_AD7816) || defined(CONFIG_AD7816_MODULE)
+	{
+		.modalias = "ad7818",
+		.max_speed_hz = 1000000,
+		.bus_num = 0,
+		.chip_select = 4,            /* CS, change it for your board */
+		.platform_data = ad7816_platform_data,
+		.controller_data = &ad7816_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_ADT7310) || defined(CONFIG_ADT7310_MODULE)
+	{
+		.modalias = "adt7310",
+		.max_speed_hz = 1000000,
+		.irq = IRQ_PG5,		/* CT alarm event. Line 0 */
+		.bus_num = 0,
+		.chip_select = 4,	/* CS, change it for your board */
+		.platform_data = adt7310_platform_data,
+		.controller_data = &adt7310_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_AD7298) || defined(CONFIG_AD7298_MODULE)
+	{
+		.modalias = "ad7298",
+		.max_speed_hz = 1000000,
+		.bus_num = 0,
+		.chip_select = 4,            /* CS, change it for your board */
+		.platform_data = ad7298_platform_data,
+		.controller_data = &ad7298_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_ADT7316_SPI) || defined(CONFIG_ADT7316_SPI_MODULE)
+	{
+		.modalias = "adt7316",
+		.max_speed_hz = 1000000,
+		.irq = IRQ_PG5,		/* interrupt line */
+		.bus_num = 0,
+		.chip_select = 4,	/* CS, change it for your board */
+		.platform_data = adt7316_spi_data,
+		.controller_data = &adt7316_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -1103,7 +1246,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.irq = IRQ_PF6,
 		.bus_num = 0,
-		.chip_select = 0,	/* GPIO controlled SSEL */
+		.chip_select = GPIO_PF10 + MAX_CTRL_CS,	/* GPIO controlled SSEL */
 		.controller_data = &enc28j60_spi_chip_info,
 		.mode = SPI_MODE_0,
 	},
@@ -1125,7 +1268,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.modalias = "adf702x",
 		.max_speed_hz = 16000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = 0,	/* GPIO controlled SSEL */
+		.chip_select = GPIO_PF10 + MAX_CTRL_CS,	/* GPIO controlled SSEL */
 		.controller_data = &adf7021_spi_chip_info,
 		.platform_data = &adf7021_platform_data,
 		.mode = SPI_MODE_0,
@@ -1143,12 +1286,239 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_0,
 	},
 #endif
+#if defined(CONFIG_AD7476) \
+	|| defined(CONFIG_AD7476_MODULE)
+	{
+		.modalias = "ad7476", /* Name of spi_driver for this device */
+		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_ad7476_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_ADE7753) \
+	|| defined(CONFIG_ADE7753_MODULE)
+	{
+		.modalias = "ade7753",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_1,
+	},
+#endif
+#if defined(CONFIG_ADE7754) \
+	|| defined(CONFIG_ADE7754_MODULE)
+	{
+		.modalias = "ade7754",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_1,
+	},
+#endif
+#if defined(CONFIG_ADE7758) \
+	|| defined(CONFIG_ADE7758_MODULE)
+	{
+		.modalias = "ade7758",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_1,
+	},
+#endif
+#if defined(CONFIG_ADE7759) \
+	|| defined(CONFIG_ADE7759_MODULE)
+	{
+		.modalias = "ade7759",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_1,
+	},
+#endif
+#if defined(CONFIG_ADE7854_SPI) \
+	|| defined(CONFIG_ADE7854_SPI_MODULE)
+	{
+		.modalias = "ade7854",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_ADIS16060) \
+	|| defined(CONFIG_ADIS16060_MODULE)
+	{
+		.modalias = "adis16060_r",
+		.max_speed_hz = 2900000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = MAX_CTRL_CS + 1, /* CS for read, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_0,
+	},
+	{
+		.modalias = "adis16060_w",
+		.max_speed_hz = 2900000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 2, /* CS for write, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_1,
+	},
+#endif
+#if defined(CONFIG_ADIS16130) \
+	|| defined(CONFIG_ADIS16130_MODULE)
+	{
+		.modalias = "adis16130",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS for read, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_ADIS16201) \
+	|| defined(CONFIG_ADIS16201_MODULE)
+	{
+		.modalias = "adis16201",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16203) \
+	|| defined(CONFIG_ADIS16203_MODULE)
+	{
+		.modalias = "adis16203",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16204) \
+	|| defined(CONFIG_ADIS16204_MODULE)
+	{
+		.modalias = "adis16204",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16209) \
+	|| defined(CONFIG_ADIS16209_MODULE)
+	{
+		.modalias = "adis16209",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16220) \
+	|| defined(CONFIG_ADIS16220_MODULE)
+	{
+		.modalias = "adis16220",
+		.max_speed_hz = 2000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16240) \
+	|| defined(CONFIG_ADIS16240_MODULE)
+	{
+		.modalias = "adis16240",
+		.max_speed_hz = 1500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16260) \
+	|| defined(CONFIG_ADIS16260_MODULE)
+	{
+		.modalias = "adis16260",
+		.max_speed_hz = 1500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16261) \
+	|| defined(CONFIG_ADIS16261_MODULE)
+	{
+		.modalias = "adis16261",
+		.max_speed_hz = 2500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_ADIS16300) \
+	|| defined(CONFIG_ADIS16300_MODULE)
+	{
+		.modalias = "adis16300",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16350) \
+	|| defined(CONFIG_ADIS16350_MODULE)
+	{
+		.modalias = "adis16364",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 5, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+		.irq = IRQ_PF4,
+	},
+#endif
+#if defined(CONFIG_ADIS16400) \
+	|| defined(CONFIG_ADIS16400_MODULE)
+	{
+		.modalias = "adis16400",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1, /* CS, change it for your board */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.mode = SPI_MODE_3,
+	},
+#endif
 };
 
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
-	.num_chipselect = 8,
+	.num_chipselect = MAX_CTRL_CS + MAX_BLACKFIN_GPIOS,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
@@ -1773,12 +2143,6 @@ static struct regulator_init_data ad5398_regulator_data = {
 	.consumer_supplies     = &ad5398_consumer,
 };
 
-static struct ad5398_platform_data ad5398_i2c_platform_data = {
-	.current_bits = 10,
-	.current_offset = 4,
-	.regulator_data = &ad5398_regulator_data,
-};
-
 #if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
 	defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
 static struct platform_device ad5398_virt_consumer_device = {
@@ -1811,7 +2175,34 @@ static struct platform_device ad5398_userspace_consumer_device = {
 #endif
 #endif
 
+#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+/* INT bound temperature alarm event. line 1 */
+static unsigned long adt7410_platform_data[2] = {
+	IRQ_PG4, IRQF_TRIGGER_LOW,
+};
+#endif
+
+#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+/* INT bound temperature alarm event. line 1 */
+static unsigned long adt7316_i2c_data[2] = {
+	IRQF_TRIGGER_LOW, /* interrupt flags */
+	GPIO_PF4, /* ldac_pin, 0 means DAC/LDAC registers control DAC update */
+};
+#endif
+
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+#if defined(CONFIG_SND_BF5XX_SOC_AD193X) || defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
+	{
+		I2C_BOARD_INFO("ad1937", 0x04),
+	},
+#endif
+
+#if defined(CONFIG_SND_BF5XX_SOC_ADAV80X) || defined(CONFIG_SND_BF5XX_SOC_ADAV80X_MODULE)
+	{
+		I2C_BOARD_INFO("adav803", 0x10),
+	},
+#endif
+
 #if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
 	{
 		I2C_BOARD_INFO("ad7142_captouch", 0x2C),
@@ -1843,12 +2234,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 	{
 		I2C_BOARD_INFO("ad7414", 0x9),
 		.irq = IRQ_PG5,
-		/*
-		 * platform_data pointer is borrwoed by the driver to
-		 * store custimer defined IRQ ALART level mode.
-		 * only IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW are valid.
-		 */
-		.platform_data = (void *)IRQF_TRIGGER_LOW,
+		.irq_flags = IRQF_TRIGGER_LOW,
 	},
 #endif
 
@@ -1856,12 +2242,56 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 	{
 		I2C_BOARD_INFO("ad7417", 0xb),
 		.irq = IRQ_PG5,
-		/*
-		 * platform_data pointer is borrwoed by the driver to
-		 * store custimer defined IRQ ALART level mode.
-		 * only IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW are valid.
-		 */
-		.platform_data = (void *)IRQF_TRIGGER_LOW,
+		.irq_flags = IRQF_TRIGGER_LOW,
+		.platform_data = (void *)GPIO_PF4,
+	},
+#endif
+
+#if defined(CONFIG_ADE7854_I2C) || defined(CONFIG_ADE7854_I2C_MODULE)
+	{
+		I2C_BOARD_INFO("ade7854", 0x38),
+	},
+#endif
+
+#if defined(CONFIG_ADT75) || defined(CONFIG_ADT75_MODULE)
+	{
+		I2C_BOARD_INFO("adt75", 0x9),
+		.irq = IRQ_PG5,
+		.irq_flags = IRQF_TRIGGER_LOW,
+	},
+#endif
+
+#if defined(CONFIG_ADT7408) || defined(CONFIG_ADT7408_MODULE)
+	{
+		I2C_BOARD_INFO("adt7408", 0x18),
+		.irq = IRQ_PG5,
+		.irq_flags = IRQF_TRIGGER_LOW,
+	},
+#endif
+
+#if defined(CONFIG_ADT7410) || defined(CONFIG_ADT7410_MODULE)
+	{
+		I2C_BOARD_INFO("adt7410", 0x48),
+		/* CT critical temperature event. line 0 */
+		.irq = IRQ_PG5,
+		.irq_flags = IRQF_TRIGGER_LOW,
+		.platform_data = (void *)&adt7410_platform_data,
+	},
+#endif
+
+#if defined(CONFIG_AD7291) || defined(CONFIG_AD7291_MODULE)
+	{
+		I2C_BOARD_INFO("ad7291", 0x20),
+		.irq = IRQ_PG5,
+		.irq_flags = IRQF_TRIGGER_LOW,
+	},
+#endif
+
+#if defined(CONFIG_ADT7316_I2C) || defined(CONFIG_ADT7316_I2C_MODULE)
+	{
+		I2C_BOARD_INFO("adt7316", 0x48),
+		.irq = IRQ_PG6,
+		.platform_data = (void *)&adt7316_i2c_data,
 	},
 #endif
 
@@ -1917,7 +2347,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 #endif
 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
 	{
-		I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2C),
+		I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2F),
 	},
 #endif
 #if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
@@ -1954,7 +2384,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 #if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
 	{
 		I2C_BOARD_INFO("ad5398", 0xC),
-		.platform_data = (void *)&ad5398_i2c_platform_data,
+		.platform_data = (void *)&ad5398_regulator_data,
 	},
 #endif
 #if defined(CONFIG_BACKLIGHT_ADP8860) || defined(CONFIG_BACKLIGHT_ADP8860_MODULE)
@@ -1963,6 +2393,16 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		.platform_data = (void *)&adp8860_pdata,
 	},
 #endif
+#if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
+	{
+		I2C_BOARD_INFO("adau1373", 0x1A),
+	},
+#endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+	{
+		I2C_BOARD_INFO("ad5252", 0x2e),
+	},
+#endif
 };
 
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
@@ -2147,50 +2587,38 @@ static struct platform_device bfin_ac97 = {
 };
 #endif
 
-#if defined(CONFIG_REGULATOR_ADP_SWITCH) || defined(CONFIG_REGULATOR_ADP_SWITCH_MODULE)
-#define REGULATOR_ADP122        "adp122"
-#define REGULATOR_ADP150        "adp150"
+#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+#define REGULATOR_ADP122	"adp122"
+#define REGULATOR_ADP122_UV	2500000
 
 static struct regulator_consumer_supply adp122_consumers = {
 		.supply = REGULATOR_ADP122,
 };
 
-static struct regulator_consumer_supply adp150_consumers = {
-		.supply = REGULATOR_ADP150,
-};
-
-static struct regulator_init_data adp_switch_regulator_data[] = {
-	{
-		.constraints = {
-			.name = REGULATOR_ADP122,
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-			.min_uA = 0,
-			.max_uA = 300000,
-		},
-		.num_consumer_supplies = 1,	/* only 1 */
-		.consumer_supplies     = &adp122_consumers,
-		.driver_data	       = (void *)GPIO_PF2, /* gpio port only */
-	},
-	{
-		.constraints = {
-			.name = REGULATOR_ADP150,
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-			.min_uA = 0,
-			.max_uA = 150000,
-		},
-		.num_consumer_supplies = 1,	/* only 1 */
-		.consumer_supplies     = &adp150_consumers,
-		.driver_data	       = (void *)GPIO_PF3, /* gpio port only */
+static struct regulator_init_data adp_switch_regulator_data = {
+	.constraints = {
+		.name = REGULATOR_ADP122,
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+		.min_uV = REGULATOR_ADP122_UV,
+		.max_uV = REGULATOR_ADP122_UV,
+		.min_uA = 0,
+		.max_uA = 300000,
 	},
+	.num_consumer_supplies = 1,	/* only 1 */
+	.consumer_supplies     = &adp122_consumers,
 };
 
-static struct adp_switch_platform_data adp_switch_pdata = {
-	.regulator_num = ARRAY_SIZE(adp_switch_regulator_data),
-	.regulator_data = adp_switch_regulator_data,
+static struct fixed_voltage_config adp_switch_pdata = {
+	.supply_name = REGULATOR_ADP122,
+	.microvolts = REGULATOR_ADP122_UV,
+	.gpio = GPIO_PF2,
+	.enable_high = 1,
+	.enabled_at_boot = 0,
+	.init_data = &adp_switch_regulator_data,
 };
 
 static struct platform_device adp_switch_device = {
-	.name = "adp_switch",
+	.name = "reg-fixed-voltage",
 	.id = 0,
 	.dev = {
 		.platform_data = &adp_switch_pdata,
@@ -2216,27 +2644,26 @@ static struct platform_device adp122_userspace_consumer_device = {
 		.platform_data = &adp122_userspace_comsumer_data,
 	},
 };
+#endif
+#endif
 
-static struct regulator_bulk_data adp150_bulk_data = {
-	.supply = REGULATOR_ADP150,
-};
+#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
+	defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
 
-static struct regulator_userspace_consumer_data adp150_userspace_comsumer_data = {
-	.name = REGULATOR_ADP150,
-	.num_supplies = 1,
-	.supplies = &adp150_bulk_data,
+static struct resource iio_gpio_trigger_resources[] = {
+	[0] = {
+		.start  = IRQ_PF5,
+		.end    = IRQ_PF5,
+		.flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
+	},
 };
 
-static struct platform_device adp150_userspace_consumer_device = {
-	.name = "reg-userspace-consumer",
-	.id = 1,
-	.dev = {
-		.platform_data = &adp150_userspace_comsumer_data,
-	},
+static struct platform_device iio_gpio_trigger = {
+	.name = "iio_gpio_trigger",
+	.num_resources = ARRAY_SIZE(iio_gpio_trigger_resources),
+	.resource = iio_gpio_trigger_resources,
 };
 #endif
-#endif
-
 
 static struct platform_device *stamp_devices[] __initdata = {
 
@@ -2369,14 +2796,18 @@ static struct platform_device *stamp_devices[] __initdata = {
 #endif
 #endif
 
-#if defined(CONFIG_REGULATOR_ADP_SWITCH) || defined(CONFIG_REGULATOR_ADP_SWITCH_MODULE)
+#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
 	&adp_switch_device,
 #if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
 	defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
 	&adp122_userspace_consumer_device,
-	&adp150_userspace_consumer_device,
 #endif
 #endif
+
+#if defined(CONFIG_IIO_GPIO_TRIGGER) || \
+	defined(CONFIG_IIO_GPIO_TRIGGER_MODULE)
+	&iio_gpio_trigger,
+#endif
 };
 
 static int __init stamp_init(void)

arch/blackfin/mach-bf537/boards/tcm_bf537.c

@@ -74,7 +74,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -113,12 +113,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -230,7 +230,7 @@ static struct resource isp1362_hcd_resources[] = {
 	}, {
 		.start = IRQ_PG15,
 		.end = IRQ_PG15,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 

arch/blackfin/mach-bf537/include/mach/defBF534.h

@@ -1071,50 +1071,6 @@
 #define FPE			0x10	/* Force Parity Error On Transmit       */
 #define FFE			0x20	/* Force Framing Error On Transmit      */
 
-/* ***********  SERIAL PERIPHERAL INTERFACE (SPI) MASKS  ****************************/
-/* SPI_CTL Masks																	*/
-#define	TIMOD		0x0003	/* Transfer Initiate Mode                                                       */
-#define RDBR_CORE	0x0000	/*              RDBR Read Initiates, IRQ When RDBR Full         */
-#define	TDBR_CORE	0x0001	/*              TDBR Write Initiates, IRQ When TDBR Empty       */
-#define RDBR_DMA	0x0002	/*              DMA Read, DMA Until FIFO Empty                          */
-#define TDBR_DMA	0x0003	/*              DMA Write, DMA Until FIFO Full                          */
-#define SZ			0x0004	/* Send Zero (When TDBR Empty, Send Zero/Last*)         */
-#define GM			0x0008	/* Get More (When RDBR Full, Overwrite/Discard*)        */
-#define PSSE		0x0010	/* Slave-Select Input Enable                                            */
-#define EMISO		0x0020	/* Enable MISO As Output                                                        */
-#define SIZE		0x0100	/* Size of Words (16/8* Bits)                                           */
-#define LSBF		0x0200	/* LSB First                                                                            */
-#define CPHA		0x0400	/* Clock Phase                                                                          */
-#define CPOL		0x0800	/* Clock Polarity                                                                       */
-#define MSTR		0x1000	/* Master/Slave*                                                                        */
-#define WOM			0x2000	/* Write Open Drain Master                                                      */
-#define SPE			0x4000	/* SPI Enable                                                                           */
-
-/* SPI_FLG Masks																	*/
-#define FLS1		0x0002	/* Enables SPI_FLOUT1 as SPI Slave-Select Output        */
-#define FLS2		0x0004	/* Enables SPI_FLOUT2 as SPI Slave-Select Output        */
-#define FLS3		0x0008	/* Enables SPI_FLOUT3 as SPI Slave-Select Output        */
-#define FLS4		0x0010	/* Enables SPI_FLOUT4 as SPI Slave-Select Output        */
-#define FLS5		0x0020	/* Enables SPI_FLOUT5 as SPI Slave-Select Output        */
-#define FLS6		0x0040	/* Enables SPI_FLOUT6 as SPI Slave-Select Output        */
-#define FLS7		0x0080	/* Enables SPI_FLOUT7 as SPI Slave-Select Output        */
-#define FLG1		0xFDFF	/* Activates SPI_FLOUT1                                                         */
-#define FLG2		0xFBFF	/* Activates SPI_FLOUT2                                                         */
-#define FLG3		0xF7FF	/* Activates SPI_FLOUT3                                                         */
-#define FLG4		0xEFFF	/* Activates SPI_FLOUT4                                                         */
-#define FLG5		0xDFFF	/* Activates SPI_FLOUT5                                                         */
-#define FLG6		0xBFFF	/* Activates SPI_FLOUT6                                                         */
-#define FLG7		0x7FFF	/* Activates SPI_FLOUT7                                                         */
-
-/* SPI_STAT Masks																				*/
-#define SPIF		0x0001	/* SPI Finished (Single-Word Transfer Complete)                                 */
-#define MODF		0x0002	/* Mode Fault Error (Another Device Tried To Become Master)             */
-#define TXE			0x0004	/* Transmission Error (Data Sent With No New Data In TDBR)              */
-#define TXS			0x0008	/* SPI_TDBR Data Buffer Status (Full/Empty*)                                    */
-#define RBSY		0x0010	/* Receive Error (Data Received With RDBR Full)                                 */
-#define RXS			0x0020	/* SPI_RDBR Data Buffer Status (Full/Empty*)                                    */
-#define TXCOL		0x0040	/* Transmit Collision Error (Corrupt Data May Have Been Sent)   */
-
 /*  ****************  GENERAL PURPOSE TIMER MASKS  **********************/
 /* TIMER_ENABLE Masks													*/
 #define TIMEN0			0x0001	/* Enable Timer 0                                       */

arch/blackfin/mach-bf538/boards/ezkit.c

@@ -695,7 +695,7 @@ static struct platform_device bf538_spi_master0 = {
 };
 
 static struct bfin5xx_spi_master bf538_spi_master_info1 = {
-	.num_chipselect = 8,
+	.num_chipselect = 2,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
@@ -711,7 +711,7 @@ static struct platform_device bf538_spi_master1 = {
 };
 
 static struct bfin5xx_spi_master bf538_spi_master_info2 = {
-	.num_chipselect = 8,
+	.num_chipselect = 2,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI2_SCK, P_SPI2_MISO, P_SPI2_MOSI, 0},
 };

arch/blackfin/mach-bf538/include/mach/defBF539.h

@@ -32,6 +32,7 @@
 /* System Interrupt Controller (0xFFC00100 - 0xFFC001FF) */
 #define	SWRST			0xFFC00100  /* Software	Reset Register (16-bit) */
 #define	SYSCR			0xFFC00104  /* System Configuration registe */
+#define	SIC_RVECT		0xFFC00108
 #define	SIC_IMASK0		0xFFC0010C  /* Interrupt Mask Register */
 #define	SIC_IAR0		0xFFC00110  /* Interrupt Assignment Register 0 */
 #define	SIC_IAR1		0xFFC00114  /* Interrupt Assignment Register 1 */
@@ -1894,78 +1895,6 @@
 #define	PE14_P	0xE
 #define	PE15_P	0xF
 
-
-/* ***********	SERIAL PERIPHERAL INTERFACE (SPI) MASKS	 **************** */
-/* SPIx_CTL Masks */
-#define	TIMOD		0x0003		/* Transfer Initiate Mode */
-#define	RDBR_CORE	0x0000		/*		RDBR Read Initiates, IRQ When RDBR Full */
-#define	TDBR_CORE	0x0001		/*		TDBR Write Initiates, IRQ When TDBR Empty */
-#define	RDBR_DMA	0x0002		/*		DMA Read, DMA Until FIFO Empty */
-#define	TDBR_DMA	0x0003		/*		DMA Write, DMA Until FIFO Full */
-#define	SZ			0x0004		/* Send	Zero (When TDBR	Empty, Send Zero/Last*) */
-#define	GM			0x0008		/* Get More (When RDBR Full, Overwrite/Discard*) */
-#define	PSSE		0x0010		/* Slave-Select	Input Enable */
-#define	EMISO		0x0020		/* Enable MISO As Output */
-#define	SIZE		0x0100		/* Size	of Words (16/8*	Bits) */
-#define	LSBF		0x0200		/* LSB First			 */
-#define	CPHA		0x0400		/* Clock Phase			 */
-#define	CPOL		0x0800		/* Clock Polarity		 */
-#define	MSTR		0x1000		/* Master/Slave*		 */
-#define	WOM			0x2000		/* Write Open Drain Master */
-#define	SPE			0x4000		/* SPI Enable			 */
-
-/* SPIx_FLG Masks */
-#define	FLS1	0x0002	/* Enables (=1)	SPI_FLOUT1 as flag output for SPI Slave-select */
-#define	FLS2	0x0004	/* Enables (=1)	SPI_FLOUT2 as flag output for SPI Slave-select */
-#define	FLS3	0x0008	/* Enables (=1)	SPI_FLOUT3 as flag output for SPI Slave-select */
-#define	FLS4	0x0010	/* Enables (=1)	SPI_FLOUT4 as flag output for SPI Slave-select */
-#define	FLS5	0x0020	/* Enables (=1)	SPI_FLOUT5 as flag output for SPI Slave-select */
-#define	FLS6	0x0040	/* Enables (=1)	SPI_FLOUT6 as flag output for SPI Slave-select */
-#define	FLS7	0x0080	/* Enables (=1)	SPI_FLOUT7 as flag output for SPI Slave-select */
-
-#define	FLG1	0x0200	/* Activates (=0) SPI_FLOUT1 as	flag output for	SPI Slave-select  */
-#define	FLG2	0x0400	/* Activates (=0) SPI_FLOUT2 as	flag output for	SPI Slave-select */
-#define	FLG3	0x0800	/* Activates (=0) SPI_FLOUT3 as	flag output for	SPI Slave-select  */
-#define	FLG4	0x1000	/* Activates (=0) SPI_FLOUT4 as	flag output for	SPI Slave-select  */
-#define	FLG5	0x2000	/* Activates (=0) SPI_FLOUT5 as	flag output for	SPI Slave-select  */
-#define	FLG6	0x4000	/* Activates (=0) SPI_FLOUT6 as	flag output for	SPI Slave-select  */
-#define	FLG7	0x8000	/* Activates (=0) SPI_FLOUT7 as	flag output for	SPI Slave-select */
-
-/* SPIx_FLG Bit	Positions */
-#define	FLS1_P	0x0001	/* Enables (=1)	SPI_FLOUT1 as flag output for SPI Slave-select */
-#define	FLS2_P	0x0002	/* Enables (=1)	SPI_FLOUT2 as flag output for SPI Slave-select */
-#define	FLS3_P	0x0003	/* Enables (=1)	SPI_FLOUT3 as flag output for SPI Slave-select */
-#define	FLS4_P	0x0004	/* Enables (=1)	SPI_FLOUT4 as flag output for SPI Slave-select */
-#define	FLS5_P	0x0005	/* Enables (=1)	SPI_FLOUT5 as flag output for SPI Slave-select */
-#define	FLS6_P	0x0006	/* Enables (=1)	SPI_FLOUT6 as flag output for SPI Slave-select */
-#define	FLS7_P	0x0007	/* Enables (=1)	SPI_FLOUT7 as flag output for SPI Slave-select */
-#define	FLG1_P	0x0009	/* Activates (=0) SPI_FLOUT1 as	flag output for	SPI Slave-select  */
-#define	FLG2_P	0x000A	/* Activates (=0) SPI_FLOUT2 as	flag output for	SPI Slave-select */
-#define	FLG3_P	0x000B	/* Activates (=0) SPI_FLOUT3 as	flag output for	SPI Slave-select  */
-#define	FLG4_P	0x000C	/* Activates (=0) SPI_FLOUT4 as	flag output for	SPI Slave-select  */
-#define	FLG5_P	0x000D	/* Activates (=0) SPI_FLOUT5 as	flag output for	SPI Slave-select  */
-#define	FLG6_P	0x000E	/* Activates (=0) SPI_FLOUT6 as	flag output for	SPI Slave-select  */
-#define	FLG7_P	0x000F	/* Activates (=0) SPI_FLOUT7 as	flag output for	SPI Slave-select */
-
-/* SPIx_STAT Masks */
-#define	SPIF	0x0001	/* Set (=1) when SPI single-word transfer complete */
-#define	MODF	0x0002	/* Set (=1) in a master	device when some other device tries to become master */
-#define	TXE		0x0004	/* Set (=1) when transmission occurs with no new data in SPI_TDBR */
-#define	TXS		0x0008	/* SPI_TDBR Data Buffer	Status (0=Empty, 1=Full) */
-#define	RBSY	0x0010	/* Set (=1) when data is received with RDBR full */
-#define	RXS		0x0020	/* SPI_RDBR Data Buffer	Status (0=Empty, 1=Full)  */
-#define	TXCOL	0x0040	/* When	set (=1), corrupt data may have	been transmitted  */
-
-/* SPIx_FLG Masks										 */
-#define	FLG1E	0xFDFF		/* Activates SPI_FLOUT1	 */
-#define	FLG2E	0xFBFF		/* Activates SPI_FLOUT2	 */
-#define	FLG3E	0xF7FF		/* Activates SPI_FLOUT3	 */
-#define	FLG4E	0xEFFF		/* Activates SPI_FLOUT4	 */
-#define	FLG5E	0xDFFF		/* Activates SPI_FLOUT5	 */
-#define	FLG6E	0xBFFF		/* Activates SPI_FLOUT6	 */
-#define	FLG7E	0x7FFF		/* Activates SPI_FLOUT7	 */
-
-
 /* *********************  ASYNCHRONOUS MEMORY CONTROLLER MASKS	************* */
 /* EBIU_AMGCTL Masks */
 #define	AMCKEN		0x0001	/* Enable CLKOUT */

arch/blackfin/mach-bf548/boards/cm_bf548.c

@@ -753,6 +753,44 @@ static struct platform_device bf54x_sdh_device = {
 };
 #endif
 
+#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+unsigned short bfin_can_peripherals[] = {
+	P_CAN0_RX, P_CAN0_TX, 0
+};
+
+static struct resource bfin_can_resources[] = {
+	{
+		.start = 0xFFC02A00,
+		.end = 0xFFC02FFF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_CAN0_RX,
+		.end = IRQ_CAN0_RX,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_CAN0_TX,
+		.end = IRQ_CAN0_TX,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_CAN0_ERROR,
+		.end = IRQ_CAN0_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_can_device = {
+	.name = "bfin_can",
+	.num_resources = ARRAY_SIZE(bfin_can_resources),
+	.resource = bfin_can_resources,
+	.dev = {
+		.platform_data = &bfin_can_peripherals, /* Passed to driver */
+	},
+};
+#endif
+
 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 static struct mtd_partition para_partitions[] = {
 	{
@@ -928,7 +966,7 @@ static struct resource bfin_spi1_resource[] = {
 
 /* SPI controller data */
 static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
-	.num_chipselect = 3,
+	.num_chipselect = 4,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
@@ -944,7 +982,7 @@ static struct platform_device bf54x_spi_master0 = {
 };
 
 static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
-	.num_chipselect = 3,
+	.num_chipselect = 4,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
@@ -1152,6 +1190,11 @@ static struct platform_device *cm_bf548_devices[] __initdata = {
 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 	&para_flash_device,
 #endif
+
+#if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
+	&bfin_can_device,
+#endif
+
 };
 
 static int __init cm_bf548_init(void)

arch/blackfin/mach-bf548/boards/ezkit.c

@@ -837,8 +837,12 @@ static struct platform_device bfin_atapi_device = {
 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 static struct mtd_partition partition_info[] = {
 	{
-		.name = "linux kernel(nand)",
+		.name = "bootloader(nand)",
 		.offset = 0,
+		.size = 0x80000,
+	}, {
+		.name = "linux kernel(nand)",
+		.offset = MTDPART_OFS_APPEND,
 		.size = 4 * 1024 * 1024,
 	},
 	{
@@ -901,7 +905,7 @@ static struct platform_device bf54x_sdh_device = {
 static struct mtd_partition ezkit_partitions[] = {
 	{
 		.name       = "bootloader(nor)",
-		.size       = 0x40000,
+		.size       = 0x80000,
 		.offset     = 0,
 	}, {
 		.name       = "linux kernel(nor)",
@@ -943,7 +947,7 @@ static struct platform_device ezkit_flash_device = {
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
-		.size = 0x00040000,
+		.size = 0x00080000,
 		.offset = 0,
 		.mask_flags = MTD_CAP_ROM
 	}, {
@@ -966,8 +970,8 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -1023,13 +1027,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 1,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -1107,7 +1111,7 @@ static struct resource bfin_spi1_resource[] = {
 
 /* SPI controller data */
 static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
-	.num_chipselect = 3,
+	.num_chipselect = 4,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
@@ -1123,7 +1127,7 @@ static struct platform_device bf54x_spi_master0 = {
 };
 
 static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
-	.num_chipselect = 3,
+	.num_chipselect = 4,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
@@ -1206,6 +1210,11 @@ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = {
 		.platform_data = (void *)&adxl34x_info,
 	},
 #endif
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
+	{
+		I2C_BOARD_INFO("ad5252", 0x2f),
+	},
+#endif
 };
 #endif
 

arch/blackfin/mach-bf548/dma.c

@@ -63,6 +63,7 @@ int channel2irq(unsigned int channel)
 		break;
 	case CH_SPORT1_TX:
 		ret_irq = IRQ_SPORT1_TX;
+		break;
 	case CH_SPI0:
 		ret_irq = IRQ_SPI0;
 		break;

arch/blackfin/mach-bf548/include/mach/cdefBF54x_base.h

@@ -40,6 +40,8 @@
 
 /* SIC Registers */
 
+#define bfin_read_SIC_RVECT()		bfin_read32(SIC_RVECT)
+#define bfin_write_SIC_RVECT(val)	bfin_write32(SIC_RVECT, val)
 #define bfin_read_SIC_IMASK0()		bfin_read32(SIC_IMASK0)
 #define bfin_write_SIC_IMASK0(val)	bfin_write32(SIC_IMASK0, val)
 #define bfin_read_SIC_IMASK1()		bfin_read32(SIC_IMASK1)

arch/blackfin/mach-bf548/include/mach/defBF54x_base.h

@@ -35,6 +35,7 @@
 
 /* SIC Registers */
 
+#define                        SIC_RVECT  0xffc00108
 #define                       SIC_IMASK0  0xffc0010c   /* System Interrupt Mask Register 0 */
 #define                       SIC_IMASK1  0xffc00110   /* System Interrupt Mask Register 1 */
 #define                       SIC_IMASK2  0xffc00114   /* System Interrupt Mask Register 2 */
@@ -2061,56 +2062,6 @@
 #define                  LOW_EVEN  0xff0000   /* Lower Limit for Even Bytes (Luma) */
 #define                 HIGH_EVEN  0xff000000 /* Upper Limit for Even Bytes (Luma) */
 
-/* Bit masks for SPIx_BAUD */
-
-#define                  SPI_BAUD  0xffff     /* Baud Rate */
-
-/* Bit masks for SPIx_CTL */
-
-#define                       SPE  0x4000     /* SPI Enable */
-#define                       WOM  0x2000     /* Write Open Drain Master */
-#define                      MSTR  0x1000     /* Master Mode */
-#define                      CPOL  0x800      /* Clock Polarity */
-#define                      CPHA  0x400      /* Clock Phase */
-#define                      LSBF  0x200      /* LSB First */
-#define                      SIZE  0x100      /* Size of Words */
-#define                     EMISO  0x20       /* Enable MISO Output */
-#define                      PSSE  0x10       /* Slave-Select Enable */
-#define                        GM  0x8        /* Get More Data */
-#define                        SZ  0x4        /* Send Zero */
-#define                     TIMOD  0x3        /* Transfer Initiation Mode */
-
-/* Bit masks for SPIx_FLG */
-
-#define                      FLS1  0x2        /* Slave Select Enable 1 */
-#define                      FLS2  0x4        /* Slave Select Enable 2 */
-#define                      FLS3  0x8        /* Slave Select Enable 3 */
-#define                      FLG1  0x200      /* Slave Select Value 1 */
-#define                      FLG2  0x400      /* Slave Select Value 2 */
-#define                      FLG3  0x800      /* Slave Select Value 3 */
-
-/* Bit masks for SPIx_STAT */
-
-#define                     TXCOL  0x40       /* Transmit Collision Error */
-#define                       RXS  0x20       /* RDBR Data Buffer Status */
-#define                      RBSY  0x10       /* Receive Error */
-#define                       TXS  0x8        /* TDBR Data Buffer Status */
-#define                       TXE  0x4        /* Transmission Error */
-#define                      MODF  0x2        /* Mode Fault Error */
-#define                      SPIF  0x1        /* SPI Finished */
-
-/* Bit masks for SPIx_TDBR */
-
-#define                      TDBR  0xffff     /* Transmit Data Buffer */
-
-/* Bit masks for SPIx_RDBR */
-
-#define                      RDBR  0xffff     /* Receive Data Buffer */
-
-/* Bit masks for SPIx_SHADOW */
-
-#define                    SHADOW  0xffff     /* RDBR Shadow */
-
 /* ************************************************ */
 /* The TWI bit masks fields are from the ADSP-BF538 */
 /* and they have not been verified as the final     */

arch/blackfin/mach-bf561/boards/acvilon.c

@@ -302,7 +302,7 @@ static struct platform_nand_data bfin_plat_nand_data = {
 static struct resource bfin_plat_nand_resources = {
 	.start = 0x24000000,
 	.end = 0x24000000 + (1 << MAX(BFIN_NAND_PLAT_CLE, BFIN_NAND_PLAT_ALE)),
-	.flags = IORESOURCE_IO,
+	.flags = IORESOURCE_MEM,
 };
 
 static struct platform_device bfin_async_nand_device = {

arch/blackfin/mach-bf561/boards/cm_bf561.c

@@ -72,7 +72,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -111,12 +111,12 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
@@ -278,7 +278,7 @@ static struct resource isp1362_hcd_resources[] = {
 	}, {
 		.start = IRQ_PF47,
 		.end = IRQ_PF47,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 

arch/blackfin/mach-bf561/boards/ezkit.c

@@ -14,6 +14,7 @@
 #include <linux/spi/spi.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
+#include <linux/delay.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
@@ -74,7 +75,7 @@ static struct resource isp1362_hcd_resources[] = {
 	}, {
 		.start = IRQ_PF8,
 		.end = IRQ_PF8,
-		.flags = IORESOURCE_IRQ,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };
 
@@ -274,8 +275,8 @@ static struct platform_device ezkit_flash_device = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -328,14 +329,16 @@ static struct platform_device bfin_spi0_device = {
 #endif
 
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SND_BLACKFIN_AD183X) \
-	|| defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 	{
-		.modalias = "ad1836",
+		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,
+		.platform_data = "ad1836", /* only includes chip name for the moment */
 		.controller_data = &ad1836_spi_chip_info,
+		.mode = SPI_MODE_3,
 	},
 #endif
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
@@ -377,8 +380,8 @@ static struct platform_device bfin_device_gpiokeys = {
 #include <linux/i2c-gpio.h>
 
 static struct i2c_gpio_platform_data i2c_gpio_data = {
-	.sda_pin		= 1,
-	.scl_pin		= 0,
+	.sda_pin		= GPIO_PF1,
+	.scl_pin		= GPIO_PF0,
 	.sda_is_open_drain	= 0,
 	.scl_is_open_drain	= 0,
 	.udelay			= 40,
@@ -420,6 +423,30 @@ static struct platform_device bfin_dpmc = {
 	},
 };
 
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+static struct platform_device bfin_i2s = {
+	.name = "bfin-i2s",
+	.id = CONFIG_SND_BF5XX_SPORT_NUM,
+	/* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+	.name = "bfin-tdm",
+	.id = CONFIG_SND_BF5XX_SPORT_NUM,
+	/* TODO: add platform data here */
+};
+#endif
+
+#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+static struct platform_device bfin_ac97 = {
+	.name = "bfin-ac97",
+	.id = CONFIG_SND_BF5XX_SPORT_NUM,
+	/* TODO: add platform data here */
+};
+#endif
+
 static struct platform_device *ezkit_devices[] __initdata = {
 
 	&bfin_dpmc,
@@ -467,6 +494,18 @@ static struct platform_device *ezkit_devices[] __initdata = {
 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 	&ezkit_flash_device,
 #endif
+
+#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
+	&bfin_i2s,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+	&bfin_tdm,
+#endif
+
+#if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
+	&bfin_ac97,
+#endif
 };
 
 static int __init ezkit_init(void)
@@ -484,6 +523,17 @@ static int __init ezkit_init(void)
 	SSYNC();
 #endif
 
+#if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
+	bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 15));
+	bfin_write_FIO0_FLAG_S(1 << 15);
+	SSYNC();
+	/*
+	 * This initialization lasts for approximately 4500 MCLKs.
+	 * MCLK = 12.288MHz
+	 */
+	udelay(400);
+#endif
+
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	return 0;
 }

arch/blackfin/mach-bf561/coreb.c

@@ -18,9 +18,9 @@
 #include <linux/miscdevice.h>
 #include <linux/module.h>
 
-#define CMD_COREB_START		2
-#define CMD_COREB_STOP		3
-#define CMD_COREB_RESET		4
+#define CMD_COREB_START		_IO('b', 0)
+#define CMD_COREB_STOP		_IO('b', 1)
+#define CMD_COREB_RESET		_IO('b', 2)
 
 static long
 coreb_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
@@ -29,10 +29,10 @@ coreb_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 
 	switch (cmd) {
 	case CMD_COREB_START:
-		bfin_write_SICA_SYSCR(bfin_read_SICA_SYSCR() & ~0x0020);
+		bfin_write_SYSCR(bfin_read_SYSCR() & ~0x0020);
 		break;
 	case CMD_COREB_STOP:
-		bfin_write_SICA_SYSCR(bfin_read_SICA_SYSCR() | 0x0020);
+		bfin_write_SYSCR(bfin_read_SYSCR() | 0x0020);
 		bfin_write_SICB_SYSCR(bfin_read_SICB_SYSCR() | 0x0080);
 		break;
 	case CMD_COREB_RESET:
@@ -74,3 +74,4 @@ module_exit(bf561_coreb_exit);
 
 MODULE_AUTHOR("Bas Vermeulen <bvermeul@blackstar.xs4all.nl>");
 MODULE_DESCRIPTION("BF561 Core B Support");
+MODULE_LICENSE("GPL");

arch/blackfin/mach-bf561/include/mach/blackfin.h

@@ -24,29 +24,16 @@
 #define bfin_read_FIO_INEN() bfin_read_FIO0_INEN()
 #define bfin_write_FIO_INEN(val) bfin_write_FIO0_INEN(val)
 
-#define SIC_IWR0 SICA_IWR0
-#define SIC_IWR1 SICA_IWR1
-#define SIC_IAR0 SICA_IAR0
-#define bfin_write_SIC_IMASK0 bfin_write_SICA_IMASK0
-#define bfin_write_SIC_IMASK1 bfin_write_SICA_IMASK1
-#define bfin_write_SIC_IWR0   bfin_write_SICA_IWR0
-#define bfin_write_SIC_IWR1   bfin_write_SICA_IWR1
-
-#define bfin_read_SIC_IMASK0 bfin_read_SICA_IMASK0
-#define bfin_read_SIC_IMASK1 bfin_read_SICA_IMASK1
-#define bfin_read_SIC_IWR0   bfin_read_SICA_IWR0
-#define bfin_read_SIC_IWR1   bfin_read_SICA_IWR1
-#define bfin_read_SIC_ISR0   bfin_read_SICA_ISR0
-#define bfin_read_SIC_ISR1   bfin_read_SICA_ISR1
-
-#define bfin_read_SIC_IMASK(x)		bfin_read32(SICA_IMASK0 + (x << 2))
-#define bfin_write_SIC_IMASK(x, val)	bfin_write32((SICA_IMASK0 + (x << 2)), val)
-#define bfin_read_SICB_IMASK(x)		bfin_read32(SICB_IMASK0 + (x << 2))
-#define bfin_write_SICB_IMASK(x, val)	bfin_write32((SICB_IMASK0 + (x << 2)), val)
-#define bfin_read_SIC_ISR(x)		bfin_read32(SICA_ISR0 + (x << 2))
-#define bfin_write_SIC_ISR(x, val)	bfin_write32((SICA_ISR0 + (x << 2)), val)
-#define bfin_read_SICB_ISR(x)		bfin_read32(SICB_ISR0 + (x << 2))
-#define bfin_write_SICB_ISR(x, val)	bfin_write32((SICB_ISR0 + (x << 2)), val)
+/* Weird muxer funcs which pick SIC regs from IMASK base */
+#define __SIC_MUX(base, x)		((base) + ((x) << 2))
+#define bfin_read_SIC_IMASK(x)		bfin_read32(__SIC_MUX(SIC_IMASK0, x))
+#define bfin_write_SIC_IMASK(x, val)	bfin_write32(__SIC_MUX(SIC_IMASK0, x), val)
+#define bfin_read_SICB_IMASK(x)		bfin_read32(__SIC_MUX(SICB_IMASK0, x))
+#define bfin_write_SICB_IMASK(x, val)	bfin_write32(__SIC_MUX(SICB_IMASK0, x), val)
+#define bfin_read_SIC_ISR(x)		bfin_read32(__SIC_MUX(SIC_ISR0, x))
+#define bfin_write_SIC_ISR(x, val)	bfin_write32(__SIC_MUX(SIC_ISR0, x), val)
+#define bfin_read_SICB_ISR(x)		bfin_read32(__SIC_MUX(SICB_ISR0, x))
+#define bfin_write_SICB_ISR(x, val)	bfin_write32(__SIC_MUX(SICB_ISR0, x), val)
 
 #define BFIN_UART_NR_PORTS      1
 

arch/blackfin/mach-bf561/include/mach/cdefBF561.h

@@ -30,49 +30,41 @@
 #define bfin_write_PLL_LOCKCNT(val)          bfin_write16(PLL_LOCKCNT,val)
 #define bfin_read_CHIPID()                   bfin_read32(CHIPID)
 
-/* For MMR's that are reserved on Core B, set up defines to better integrate with other ports */
-#define bfin_read_SWRST()                    bfin_read_SICA_SWRST()
-#define bfin_write_SWRST(val)                bfin_write_SICA_SWRST(val)
-#define bfin_read_SYSCR()                    bfin_read_SICA_SYSCR()
-#define bfin_write_SYSCR(val)                bfin_write_SICA_SYSCR(val)
-
 /* System Reset and Interrupt Controller registers for core A (0xFFC0 0100-0xFFC0 01FF) */
-#define bfin_read_SICA_SWRST()               bfin_read16(SICA_SWRST)
-#define bfin_write_SICA_SWRST(val)           bfin_write16(SICA_SWRST,val)
-#define bfin_read_SICA_SYSCR()               bfin_read16(SICA_SYSCR)
-#define bfin_write_SICA_SYSCR(val)           bfin_write16(SICA_SYSCR,val)
-#define bfin_read_SICA_RVECT()               bfin_read16(SICA_RVECT)
-#define bfin_write_SICA_RVECT(val)           bfin_write16(SICA_RVECT,val)
-#define bfin_read_SICA_IMASK()               bfin_read32(SICA_IMASK)
-#define bfin_write_SICA_IMASK(val)           bfin_write32(SICA_IMASK,val)
-#define bfin_read_SICA_IMASK0()              bfin_read32(SICA_IMASK0)
-#define bfin_write_SICA_IMASK0(val)          bfin_write32(SICA_IMASK0,val)
-#define bfin_read_SICA_IMASK1()              bfin_read32(SICA_IMASK1)
-#define bfin_write_SICA_IMASK1(val)          bfin_write32(SICA_IMASK1,val)
-#define bfin_read_SICA_IAR0()                bfin_read32(SICA_IAR0)
-#define bfin_write_SICA_IAR0(val)            bfin_write32(SICA_IAR0,val)
-#define bfin_read_SICA_IAR1()                bfin_read32(SICA_IAR1)
-#define bfin_write_SICA_IAR1(val)            bfin_write32(SICA_IAR1,val)
-#define bfin_read_SICA_IAR2()                bfin_read32(SICA_IAR2)
-#define bfin_write_SICA_IAR2(val)            bfin_write32(SICA_IAR2,val)
-#define bfin_read_SICA_IAR3()                bfin_read32(SICA_IAR3)
-#define bfin_write_SICA_IAR3(val)            bfin_write32(SICA_IAR3,val)
-#define bfin_read_SICA_IAR4()                bfin_read32(SICA_IAR4)
-#define bfin_write_SICA_IAR4(val)            bfin_write32(SICA_IAR4,val)
-#define bfin_read_SICA_IAR5()                bfin_read32(SICA_IAR5)
-#define bfin_write_SICA_IAR5(val)            bfin_write32(SICA_IAR5,val)
-#define bfin_read_SICA_IAR6()                bfin_read32(SICA_IAR6)
-#define bfin_write_SICA_IAR6(val)            bfin_write32(SICA_IAR6,val)
-#define bfin_read_SICA_IAR7()                bfin_read32(SICA_IAR7)
-#define bfin_write_SICA_IAR7(val)            bfin_write32(SICA_IAR7,val)
-#define bfin_read_SICA_ISR0()                bfin_read32(SICA_ISR0)
-#define bfin_write_SICA_ISR0(val)            bfin_write32(SICA_ISR0,val)
-#define bfin_read_SICA_ISR1()                bfin_read32(SICA_ISR1)
-#define bfin_write_SICA_ISR1(val)            bfin_write32(SICA_ISR1,val)
-#define bfin_read_SICA_IWR0()                bfin_read32(SICA_IWR0)
-#define bfin_write_SICA_IWR0(val)            bfin_write32(SICA_IWR0,val)
-#define bfin_read_SICA_IWR1()                bfin_read32(SICA_IWR1)
-#define bfin_write_SICA_IWR1(val)            bfin_write32(SICA_IWR1,val)
+#define bfin_read_SWRST()                    bfin_read16(SWRST)
+#define bfin_write_SWRST(val)                bfin_write16(SWRST,val)
+#define bfin_read_SYSCR()                    bfin_read16(SYSCR)
+#define bfin_write_SYSCR(val)                bfin_write16(SYSCR,val)
+#define bfin_read_SIC_RVECT()                bfin_read16(SIC_RVECT)
+#define bfin_write_SIC_RVECT(val)            bfin_write16(SIC_RVECT,val)
+#define bfin_read_SIC_IMASK0()               bfin_read32(SIC_IMASK0)
+#define bfin_write_SIC_IMASK0(val)           bfin_write32(SIC_IMASK0,val)
+#define bfin_read_SIC_IMASK1()               bfin_read32(SIC_IMASK1)
+#define bfin_write_SIC_IMASK1(val)           bfin_write32(SIC_IMASK1,val)
+#define bfin_read_SIC_IAR0()                 bfin_read32(SIC_IAR0)
+#define bfin_write_SIC_IAR0(val)             bfin_write32(SIC_IAR0,val)
+#define bfin_read_SIC_IAR1()                 bfin_read32(SIC_IAR1)
+#define bfin_write_SIC_IAR1(val)             bfin_write32(SIC_IAR1,val)
+#define bfin_read_SIC_IAR2()                 bfin_read32(SIC_IAR2)
+#define bfin_write_SIC_IAR2(val)             bfin_write32(SIC_IAR2,val)
+#define bfin_read_SIC_IAR3()                 bfin_read32(SIC_IAR3)
+#define bfin_write_SIC_IAR3(val)             bfin_write32(SIC_IAR3,val)
+#define bfin_read_SIC_IAR4()                 bfin_read32(SIC_IAR4)
+#define bfin_write_SIC_IAR4(val)             bfin_write32(SIC_IAR4,val)
+#define bfin_read_SIC_IAR5()                 bfin_read32(SIC_IAR5)
+#define bfin_write_SIC_IAR5(val)             bfin_write32(SIC_IAR5,val)
+#define bfin_read_SIC_IAR6()                 bfin_read32(SIC_IAR6)
+#define bfin_write_SIC_IAR6(val)             bfin_write32(SIC_IAR6,val)
+#define bfin_read_SIC_IAR7()                 bfin_read32(SIC_IAR7)
+#define bfin_write_SIC_IAR7(val)             bfin_write32(SIC_IAR7,val)
+#define bfin_read_SIC_ISR0()                 bfin_read32(SIC_ISR0)
+#define bfin_write_SIC_ISR0(val)             bfin_write32(SIC_ISR0,val)
+#define bfin_read_SIC_ISR1()                 bfin_read32(SIC_ISR1)
+#define bfin_write_SIC_ISR1(val)             bfin_write32(SIC_ISR1,val)
+#define bfin_read_SIC_IWR0()                 bfin_read32(SIC_IWR0)
+#define bfin_write_SIC_IWR0(val)             bfin_write32(SIC_IWR0,val)
+#define bfin_read_SIC_IWR1()                 bfin_read32(SIC_IWR1)
+#define bfin_write_SIC_IWR1(val)             bfin_write32(SIC_IWR1,val)
 
 /* System Reset and Interrupt Controller registers for Core B (0xFFC0 1100-0xFFC0 11FF) */
 #define bfin_read_SICB_SWRST()               bfin_read16(SICB_SWRST)

arch/blackfin/mach-bf561/include/mach/defBF561.h

@@ -28,32 +28,29 @@
 #define CHIPID                 0xFFC00014       /* Chip ID Register */
 
 /* For MMR's that are reserved on Core B, set up defines to better integrate with other ports */
-#define SWRST                   SICA_SWRST
-#define SYSCR                   SICA_SYSCR
 #define DOUBLE_FAULT            (DOUBLE_FAULT_B|DOUBLE_FAULT_A)
 #define RESET_DOUBLE            (SWRST_DBL_FAULT_B|SWRST_DBL_FAULT_A)
 #define RESET_WDOG              (SWRST_WDT_B|SWRST_WDT_A)
 #define RESET_SOFTWARE          (SWRST_OCCURRED)
 
 /* System Reset and Interrupt Controller registers for core A (0xFFC0 0100-0xFFC0 01FF) */
-#define SICA_SWRST              0xFFC00100	/* Software Reset register */
-#define SICA_SYSCR              0xFFC00104	/* System Reset Configuration register */
-#define SICA_RVECT              0xFFC00108	/* SIC Reset Vector Address Register */
-#define SICA_IMASK              0xFFC0010C	/* SIC Interrupt Mask register 0 - hack to fix old tests */
-#define SICA_IMASK0             0xFFC0010C	/* SIC Interrupt Mask register 0 */
-#define SICA_IMASK1             0xFFC00110	/* SIC Interrupt Mask register 1 */
-#define SICA_IAR0               0xFFC00124	/* SIC Interrupt Assignment Register 0 */
-#define SICA_IAR1               0xFFC00128	/* SIC Interrupt Assignment Register 1 */
-#define SICA_IAR2               0xFFC0012C	/* SIC Interrupt Assignment Register 2 */
-#define SICA_IAR3               0xFFC00130	/* SIC Interrupt Assignment Register 3 */
-#define SICA_IAR4               0xFFC00134	/* SIC Interrupt Assignment Register 4 */
-#define SICA_IAR5               0xFFC00138	/* SIC Interrupt Assignment Register 5 */
-#define SICA_IAR6               0xFFC0013C	/* SIC Interrupt Assignment Register 6 */
-#define SICA_IAR7               0xFFC00140	/* SIC Interrupt Assignment Register 7 */
-#define SICA_ISR0               0xFFC00114	/* SIC Interrupt Status register 0 */
-#define SICA_ISR1               0xFFC00118	/* SIC Interrupt Status register 1 */
-#define SICA_IWR0               0xFFC0011C	/* SIC Interrupt Wakeup-Enable register 0 */
-#define SICA_IWR1               0xFFC00120	/* SIC Interrupt Wakeup-Enable register 1 */
+#define SWRST                   0xFFC00100	/* Software Reset register */
+#define SYSCR                   0xFFC00104	/* System Reset Configuration register */
+#define SIC_RVECT               0xFFC00108	/* SIC Reset Vector Address Register */
+#define SIC_IMASK0              0xFFC0010C	/* SIC Interrupt Mask register 0 */
+#define SIC_IMASK1              0xFFC00110	/* SIC Interrupt Mask register 1 */
+#define SIC_IAR0                0xFFC00124	/* SIC Interrupt Assignment Register 0 */
+#define SIC_IAR1                0xFFC00128	/* SIC Interrupt Assignment Register 1 */
+#define SIC_IAR2                0xFFC0012C	/* SIC Interrupt Assignment Register 2 */
+#define SIC_IAR3                0xFFC00130	/* SIC Interrupt Assignment Register 3 */
+#define SIC_IAR4                0xFFC00134	/* SIC Interrupt Assignment Register 4 */
+#define SIC_IAR5                0xFFC00138	/* SIC Interrupt Assignment Register 5 */
+#define SIC_IAR6                0xFFC0013C	/* SIC Interrupt Assignment Register 6 */
+#define SIC_IAR7                0xFFC00140	/* SIC Interrupt Assignment Register 7 */
+#define SIC_ISR0                0xFFC00114	/* SIC Interrupt Status register 0 */
+#define SIC_ISR1                0xFFC00118	/* SIC Interrupt Status register 1 */
+#define SIC_IWR0                0xFFC0011C	/* SIC Interrupt Wakeup-Enable register 0 */
+#define SIC_IWR1                0xFFC00120	/* SIC Interrupt Wakeup-Enable register 1 */
 
 /* System Reset and Interrupt Controller registers for Core B (0xFFC0 1100-0xFFC0 11FF) */
 #define SICB_SWRST              0xFFC01100	/* reserved */
@@ -1271,63 +1268,6 @@
 #define PF14_P        14
 #define PF15_P        15
 
-/* ***********  SERIAL PERIPHERAL INTERFACE (SPI) MASKS  **************** */
-
-/* SPI_CTL Masks */
-#define TIMOD                  0x00000003	/* Transfer initiation mode and interrupt generation */
-#define SZ                     0x00000004	/* Send Zero (=0) or last (=1) word when TDBR empty. */
-#define GM                     0x00000008	/* When RDBR full, get more (=1) data or discard (=0) incoming Data */
-#define PSSE                   0x00000010	/* Enable (=1) Slave-Select input for Master. */
-#define EMISO                  0x00000020	/* Enable (=1) MISO pin as an output. */
-#define SIZE                   0x00000100	/* Word length (0 => 8 bits, 1 => 16 bits) */
-#define LSBF                   0x00000200	/* Data format (0 => MSB sent/received first 1 => LSB sent/received first) */
-#define CPHA                   0x00000400	/* Clock phase (0 => SPICLK starts toggling in middle of xfer, 1 => SPICLK toggles at the beginning of xfer. */
-#define CPOL                   0x00000800	/* Clock polarity (0 => active-high, 1 => active-low) */
-#define MSTR                   0x00001000	/* Configures SPI as master (=1) or slave (=0) */
-#define WOM                    0x00002000	/* Open drain (=1) data output enable (for MOSI and MISO) */
-#define SPE                    0x00004000	/* SPI module enable (=1), disable (=0) */
-
-/* SPI_FLG Masks */
-#define FLS1                   0x00000002	/* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2                   0x00000004	/* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3                   0x00000008	/* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4                   0x00000010	/* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5                   0x00000020	/* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6                   0x00000040	/* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7                   0x00000080	/* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1                   0x00000200	/* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select  */
-#define FLG2                   0x00000400	/* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3                   0x00000800	/* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select  */
-#define FLG4                   0x00001000	/* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select  */
-#define FLG5                   0x00002000	/* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select  */
-#define FLG6                   0x00004000	/* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select  */
-#define FLG7                   0x00008000	/* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_FLG Bit Positions */
-#define FLS1_P                 0x00000001	/* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
-#define FLS2_P                 0x00000002	/* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLS3_P                 0x00000003	/* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
-#define FLS4_P                 0x00000004	/* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
-#define FLS5_P                 0x00000005	/* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
-#define FLS6_P                 0x00000006	/* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
-#define FLS7_P                 0x00000007	/* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
-#define FLG1_P                 0x00000009	/* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select  */
-#define FLG2_P                 0x0000000A	/* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
-#define FLG3_P                 0x0000000B	/* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select  */
-#define FLG4_P                 0x0000000C	/* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select  */
-#define FLG5_P                 0x0000000D	/* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select  */
-#define FLG6_P                 0x0000000E	/* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select  */
-#define FLG7_P                 0x0000000F	/* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
-
-/* SPI_STAT Masks */
-#define SPIF                   0x00000001	/* Set (=1) when SPI single-word transfer complete */
-#define MODF                   0x00000002	/* Set (=1) in a master device when some other device tries to become master */
-#define TXE                    0x00000004	/* Set (=1) when transmission occurs with no new data in SPI_TDBR */
-#define TXS                    0x00000008	/* SPI_TDBR Data Buffer Status (0=Empty, 1=Full) */
-#define RBSY                   0x00000010	/* Set (=1) when data is received with RDBR full */
-#define RXS                    0x00000020	/* SPI_RDBR Data Buffer Status (0=Empty, 1=Full)  */
-#define TXCOL                  0x00000040	/* When set (=1), corrupt data may have been transmitted  */
-
 /* *********************  ASYNCHRONOUS MEMORY CONTROLLER MASKS  ************* */
 
 /* AMGCTL Masks */

arch/blackfin/mach-bf561/ints-priority.c

@@ -13,7 +13,7 @@
 void __init program_IAR(void)
 {
 	/* Program the IAR0 Register with the configured priority */
-	bfin_write_SICA_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) |
+	bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) |
 			     ((CONFIG_IRQ_DMA1_ERROR - 7) << IRQ_DMA1_ERROR_POS) |
 			     ((CONFIG_IRQ_DMA2_ERROR - 7) << IRQ_DMA2_ERROR_POS) |
 			     ((CONFIG_IRQ_IMDMA_ERROR - 7) << IRQ_IMDMA_ERROR_POS) |
@@ -22,7 +22,7 @@ void __init program_IAR(void)
 			     ((CONFIG_IRQ_SPORT0_ERROR - 7) << IRQ_SPORT0_ERROR_POS) |
 			     ((CONFIG_IRQ_SPORT1_ERROR - 7) << IRQ_SPORT1_ERROR_POS));
 
-	bfin_write_SICA_IAR1(((CONFIG_IRQ_SPI_ERROR - 7) << IRQ_SPI_ERROR_POS) |
+	bfin_write_SIC_IAR1(((CONFIG_IRQ_SPI_ERROR - 7) << IRQ_SPI_ERROR_POS) |
 			     ((CONFIG_IRQ_UART_ERROR - 7) << IRQ_UART_ERROR_POS) |
 			     ((CONFIG_IRQ_RESERVED_ERROR - 7) << IRQ_RESERVED_ERROR_POS) |
 			     ((CONFIG_IRQ_DMA1_0 - 7) << IRQ_DMA1_0_POS) |
@@ -31,7 +31,7 @@ void __init program_IAR(void)
 			     ((CONFIG_IRQ_DMA1_3 - 7) << IRQ_DMA1_3_POS) |
 			     ((CONFIG_IRQ_DMA1_4 - 7) << IRQ_DMA1_4_POS));
 
-	bfin_write_SICA_IAR2(((CONFIG_IRQ_DMA1_5 - 7) << IRQ_DMA1_5_POS) |
+	bfin_write_SIC_IAR2(((CONFIG_IRQ_DMA1_5 - 7) << IRQ_DMA1_5_POS) |
 			     ((CONFIG_IRQ_DMA1_6 - 7) << IRQ_DMA1_6_POS) |
 			     ((CONFIG_IRQ_DMA1_7 - 7) << IRQ_DMA1_7_POS) |
 			     ((CONFIG_IRQ_DMA1_8 - 7) << IRQ_DMA1_8_POS) |
@@ -40,7 +40,7 @@ void __init program_IAR(void)
 			     ((CONFIG_IRQ_DMA1_11 - 7) << IRQ_DMA1_11_POS) |
 			     ((CONFIG_IRQ_DMA2_0 - 7) << IRQ_DMA2_0_POS));
 
-	bfin_write_SICA_IAR3(((CONFIG_IRQ_DMA2_1 - 7) << IRQ_DMA2_1_POS) |
+	bfin_write_SIC_IAR3(((CONFIG_IRQ_DMA2_1 - 7) << IRQ_DMA2_1_POS) |
 			     ((CONFIG_IRQ_DMA2_2 - 7) << IRQ_DMA2_2_POS) |
 			     ((CONFIG_IRQ_DMA2_3 - 7) << IRQ_DMA2_3_POS) |
 			     ((CONFIG_IRQ_DMA2_4 - 7) << IRQ_DMA2_4_POS) |
@@ -49,7 +49,7 @@ void __init program_IAR(void)
 			     ((CONFIG_IRQ_DMA2_7 - 7) << IRQ_DMA2_7_POS) |
 			     ((CONFIG_IRQ_DMA2_8 - 7) << IRQ_DMA2_8_POS));
 
-	bfin_write_SICA_IAR4(((CONFIG_IRQ_DMA2_9 - 7) << IRQ_DMA2_9_POS) |
+	bfin_write_SIC_IAR4(((CONFIG_IRQ_DMA2_9 - 7) << IRQ_DMA2_9_POS) |
 			     ((CONFIG_IRQ_DMA2_10 - 7) << IRQ_DMA2_10_POS) |
 			     ((CONFIG_IRQ_DMA2_11 - 7) << IRQ_DMA2_11_POS) |
 			     ((CONFIG_IRQ_TIMER0 - 7) << IRQ_TIMER0_POS) |
@@ -58,7 +58,7 @@ void __init program_IAR(void)
 			     ((CONFIG_IRQ_TIMER3 - 7) << IRQ_TIMER3_POS) |
 			     ((CONFIG_IRQ_TIMER4 - 7) << IRQ_TIMER4_POS));
 
-	bfin_write_SICA_IAR5(((CONFIG_IRQ_TIMER5 - 7) << IRQ_TIMER5_POS) |
+	bfin_write_SIC_IAR5(((CONFIG_IRQ_TIMER5 - 7) << IRQ_TIMER5_POS) |
 			     ((CONFIG_IRQ_TIMER6 - 7) << IRQ_TIMER6_POS) |
 			     ((CONFIG_IRQ_TIMER7 - 7) << IRQ_TIMER7_POS) |
 			     ((CONFIG_IRQ_TIMER8 - 7) << IRQ_TIMER8_POS) |
@@ -67,7 +67,7 @@ void __init program_IAR(void)
 			     ((CONFIG_IRQ_TIMER11 - 7) << IRQ_TIMER11_POS) |
 			     ((CONFIG_IRQ_PROG0_INTA - 7) << IRQ_PROG0_INTA_POS));
 
-	bfin_write_SICA_IAR6(((CONFIG_IRQ_PROG0_INTB - 7) << IRQ_PROG0_INTB_POS) |
+	bfin_write_SIC_IAR6(((CONFIG_IRQ_PROG0_INTB - 7) << IRQ_PROG0_INTB_POS) |
 			     ((CONFIG_IRQ_PROG1_INTA - 7) << IRQ_PROG1_INTA_POS) |
 			     ((CONFIG_IRQ_PROG1_INTB - 7) << IRQ_PROG1_INTB_POS) |
 			     ((CONFIG_IRQ_PROG2_INTA - 7) << IRQ_PROG2_INTA_POS) |
@@ -76,7 +76,7 @@ void __init program_IAR(void)
 			     ((CONFIG_IRQ_DMA1_WRRD1 - 7) << IRQ_DMA1_WRRD1_POS) |
 			     ((CONFIG_IRQ_DMA2_WRRD0 - 7) << IRQ_DMA2_WRRD0_POS));
 
-	bfin_write_SICA_IAR7(((CONFIG_IRQ_DMA2_WRRD1 - 7) << IRQ_DMA2_WRRD1_POS) |
+	bfin_write_SIC_IAR7(((CONFIG_IRQ_DMA2_WRRD1 - 7) << IRQ_DMA2_WRRD1_POS) |
 			     ((CONFIG_IRQ_IMDMA_WRRD0 - 7) << IRQ_IMDMA_WRRD0_POS) |
 			     ((CONFIG_IRQ_IMDMA_WRRD1 - 7) << IRQ_IMDMA_WRRD1_POS) |
 			     ((CONFIG_IRQ_WDTIMER - 7) << IRQ_WDTIMER_POS) |

arch/blackfin/mach-bf561/smp.c

@@ -52,19 +52,19 @@ int __init setup_profiling_timer(unsigned int multiplier) /* not supported */
 void __cpuinit platform_secondary_init(unsigned int cpu)
 {
 	/* Clone setup for peripheral interrupt sources from CoreA. */
-	bfin_write_SICB_IMASK0(bfin_read_SICA_IMASK0());
-	bfin_write_SICB_IMASK1(bfin_read_SICA_IMASK1());
+	bfin_write_SICB_IMASK0(bfin_read_SIC_IMASK0());
+	bfin_write_SICB_IMASK1(bfin_read_SIC_IMASK1());
 	SSYNC();
 
 	/* Clone setup for IARs from CoreA. */
-	bfin_write_SICB_IAR0(bfin_read_SICA_IAR0());
-	bfin_write_SICB_IAR1(bfin_read_SICA_IAR1());
-	bfin_write_SICB_IAR2(bfin_read_SICA_IAR2());
-	bfin_write_SICB_IAR3(bfin_read_SICA_IAR3());
-	bfin_write_SICB_IAR4(bfin_read_SICA_IAR4());
-	bfin_write_SICB_IAR5(bfin_read_SICA_IAR5());
-	bfin_write_SICB_IAR6(bfin_read_SICA_IAR6());
-	bfin_write_SICB_IAR7(bfin_read_SICA_IAR7());
+	bfin_write_SICB_IAR0(bfin_read_SIC_IAR0());
+	bfin_write_SICB_IAR1(bfin_read_SIC_IAR1());
+	bfin_write_SICB_IAR2(bfin_read_SIC_IAR2());
+	bfin_write_SICB_IAR3(bfin_read_SIC_IAR3());
+	bfin_write_SICB_IAR4(bfin_read_SIC_IAR4());
+	bfin_write_SICB_IAR5(bfin_read_SIC_IAR5());
+	bfin_write_SICB_IAR6(bfin_read_SIC_IAR6());
+	bfin_write_SICB_IAR7(bfin_read_SIC_IAR7());
 	bfin_write_SICB_IWR0(IWR_DISABLE_ALL);
 	bfin_write_SICB_IWR1(IWR_DISABLE_ALL);
 	SSYNC();
@@ -86,12 +86,12 @@ int __cpuinit platform_boot_secondary(unsigned int cpu, struct task_struct *idle
 
 	spin_lock(&boot_lock);
 
-	if ((bfin_read_SICA_SYSCR() & COREB_SRAM_INIT) == 0) {
+	if ((bfin_read_SIC_SYSCR() & COREB_SRAM_INIT) == 0) {
 		/* CoreB already running, sending ipi to wakeup it */
 		platform_send_ipi_cpu(cpu, IRQ_SUPPLE_0);
 	} else {
 		/* Kick CoreB, which should start execution from CORE_SRAM_BASE. */
-		bfin_write_SICA_SYSCR(bfin_read_SICA_SYSCR() & ~COREB_SRAM_INIT);
+		bfin_write_SIC_SYSCR(bfin_read_SIC_SYSCR() & ~COREB_SRAM_INIT);
 		SSYNC();
 	}
 

arch/blackfin/mach-common/dpmc_modes.S

@@ -292,13 +292,7 @@ ENTRY(_do_hibernate)
 #ifdef SIC_IMASK
 	PM_SYS_PUSH(SIC_IMASK)
 #endif
-#ifdef SICA_IMASK0
-	PM_SYS_PUSH(SICA_IMASK0)
-#endif
-#ifdef SICA_IMASK1
-	PM_SYS_PUSH(SICA_IMASK1)
-#endif
-#ifdef SIC_IAR2
+#ifdef SIC_IAR0
 	PM_SYS_PUSH(SIC_IAR0)
 	PM_SYS_PUSH(SIC_IAR1)
 	PM_SYS_PUSH(SIC_IAR2)
@@ -321,17 +315,6 @@ ENTRY(_do_hibernate)
 	PM_SYS_PUSH(SIC_IAR11)
 #endif
 
-#ifdef SICA_IAR0
-	PM_SYS_PUSH(SICA_IAR0)
-	PM_SYS_PUSH(SICA_IAR1)
-	PM_SYS_PUSH(SICA_IAR2)
-	PM_SYS_PUSH(SICA_IAR3)
-	PM_SYS_PUSH(SICA_IAR4)
-	PM_SYS_PUSH(SICA_IAR5)
-	PM_SYS_PUSH(SICA_IAR6)
-	PM_SYS_PUSH(SICA_IAR7)
-#endif
-
 #ifdef SIC_IWR
 	PM_SYS_PUSH(SIC_IWR)
 #endif
@@ -344,12 +327,6 @@ ENTRY(_do_hibernate)
 #ifdef SIC_IWR2
 	PM_SYS_PUSH(SIC_IWR2)
 #endif
-#ifdef SICA_IWR0
-	PM_SYS_PUSH(SICA_IWR0)
-#endif
-#ifdef SICA_IWR1
-	PM_SYS_PUSH(SICA_IWR1)
-#endif
 
 #ifdef PINT0_ASSIGN
 	PM_SYS_PUSH(PINT0_MASK_SET)
@@ -750,12 +727,6 @@ ENTRY(_do_hibernate)
 	PM_SYS_POP(PINT0_MASK_SET)
 #endif
 
-#ifdef SICA_IWR1
-	PM_SYS_POP(SICA_IWR1)
-#endif
-#ifdef SICA_IWR0
-	PM_SYS_POP(SICA_IWR0)
-#endif
 #ifdef SIC_IWR2
 	PM_SYS_POP(SIC_IWR2)
 #endif
@@ -769,17 +740,6 @@ ENTRY(_do_hibernate)
 	PM_SYS_POP(SIC_IWR)
 #endif
 
-#ifdef SICA_IAR0
-	PM_SYS_POP(SICA_IAR7)
-	PM_SYS_POP(SICA_IAR6)
-	PM_SYS_POP(SICA_IAR5)
-	PM_SYS_POP(SICA_IAR4)
-	PM_SYS_POP(SICA_IAR3)
-	PM_SYS_POP(SICA_IAR2)
-	PM_SYS_POP(SICA_IAR1)
-	PM_SYS_POP(SICA_IAR0)
-#endif
-
 #ifdef SIC_IAR8
 	PM_SYS_POP(SIC_IAR11)
 	PM_SYS_POP(SIC_IAR10)
@@ -797,17 +757,11 @@ ENTRY(_do_hibernate)
 #ifdef SIC_IAR3
 	PM_SYS_POP(SIC_IAR3)
 #endif
-#ifdef SIC_IAR2
+#ifdef SIC_IAR0
 	PM_SYS_POP(SIC_IAR2)
 	PM_SYS_POP(SIC_IAR1)
 	PM_SYS_POP(SIC_IAR0)
 #endif
-#ifdef SICA_IMASK1
-	PM_SYS_POP(SICA_IMASK1)
-#endif
-#ifdef SICA_IMASK0
-	PM_SYS_POP(SICA_IMASK0)
-#endif
 #ifdef SIC_IMASK
 	PM_SYS_POP(SIC_IMASK)
 #endif

arch/blackfin/mach-common/entry.S

@@ -889,6 +889,66 @@ ENTRY(_ret_from_exception)
 	rts;
 ENDPROC(_ret_from_exception)
 
+#if defined(CONFIG_PREEMPT)
+
+ENTRY(_up_to_irq14)
+#if ANOMALY_05000281 || ANOMALY_05000461
+	r0.l = lo(SAFE_USER_INSTRUCTION);
+	r0.h = hi(SAFE_USER_INSTRUCTION);
+	reti = r0;
+#endif
+
+#ifdef CONFIG_DEBUG_HWERR
+	/* enable irq14 & hwerr interrupt, until we transition to _evt_evt14 */
+	r0 = (EVT_IVG14 | EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+#else
+	/* Only enable irq14 interrupt, until we transition to _evt_evt14 */
+	r0 = (EVT_IVG14 | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+#endif
+	sti r0;
+
+	p0.l = lo(EVT14);
+	p0.h = hi(EVT14);
+	p1.l = _evt_up_evt14;
+	p1.h = _evt_up_evt14;
+	[p0] = p1;
+	csync;
+
+	raise 14;
+1:
+	jump 1b;
+ENDPROC(_up_to_irq14)
+
+ENTRY(_evt_up_evt14)
+#ifdef CONFIG_DEBUG_HWERR
+	r0 = (EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+	sti r0;
+#else
+	cli r0;
+#endif
+#ifdef CONFIG_TRACE_IRQFLAGS
+	[--sp] = rets;
+	sp += -12;
+	call _trace_hardirqs_off;
+	sp += 12;
+	rets = [sp++];
+#endif
+	[--sp] = RETI;
+	SP += 4;
+
+	/* restore normal evt14 */
+	p0.l = lo(EVT14);
+	p0.h = hi(EVT14);
+	p1.l = _evt_evt14;
+	p1.h = _evt_evt14;
+	[p0] = p1;
+	csync;
+
+	rts;
+ENDPROC(_evt_up_evt14)
+
+#endif
+
 #ifdef CONFIG_IPIPE
 
 _resume_kernel_from_int:
@@ -902,8 +962,54 @@ _resume_kernel_from_int:
 	( r7:4, p5:3 ) = [sp++];
 	rets = [sp++];
 	rts
+#elif defined(CONFIG_PREEMPT)
+
+_resume_kernel_from_int:
+	/* check preempt_count */
+	r7 = sp;
+	r4.l = lo(ALIGN_PAGE_MASK);
+	r4.h = hi(ALIGN_PAGE_MASK);
+	r7 = r7 & r4;
+	p5 = r7;
+	r7 = [p5 + TI_PREEMPT];
+	cc = r7 == 0x0;
+	if !cc jump .Lreturn_to_kernel;
+.Lneed_schedule:
+	r7 = [p5 + TI_FLAGS];
+	r4.l = lo(_TIF_WORK_MASK);
+	r4.h = hi(_TIF_WORK_MASK);
+	r7 =  r7 & r4;
+	cc = BITTST(r7, TIF_NEED_RESCHED);
+	if !cc jump .Lreturn_to_kernel;
+	/*
+	 * let schedule done at level 15, otherwise sheduled process will run
+	 * at high level and block low level interrupt
+	 */
+	r6 = reti;  /* save reti */
+	r5.l = .Lkernel_schedule;
+	r5.h = .Lkernel_schedule;
+	reti = r5;
+	rti;
+.Lkernel_schedule:
+	[--sp] = rets;
+	sp += -12;
+	pseudo_long_call _preempt_schedule_irq, p4;
+	sp += 12;
+	rets = [sp++];
+
+	[--sp] = rets;
+	sp += -12;
+	/* up to irq14 so that reti after restore_all can return to irq15(kernel) */
+	pseudo_long_call _up_to_irq14, p4;
+	sp += 12;
+	rets = [sp++];
+
+	reti = r6; /* restore reti so that origin process can return to interrupted point */
+
+	jump .Lneed_schedule;
 #else
-#define _resume_kernel_from_int	 2f
+
+#define _resume_kernel_from_int	.Lreturn_to_kernel
 #endif
 
 ENTRY(_return_from_int)
@@ -913,7 +1019,7 @@ ENTRY(_return_from_int)
 	p2.h = hi(ILAT);
 	r0 = [p2];
 	cc = bittst (r0, EVT_IVG15_P);
-	if cc jump 2f;
+	if cc jump .Lreturn_to_kernel;
 
 	/* if not return to user mode, get out */
 	p2.l = lo(IPEND);
@@ -945,7 +1051,7 @@ ENTRY(_return_from_int)
 	STI r0;
 	raise 15;	/* raise evt15 to do signal or reschedule */
 	rti;
-2:
+.Lreturn_to_kernel:
 	rts;
 ENDPROC(_return_from_int)
 
@@ -1631,6 +1737,7 @@ ENTRY(_sys_call_table)
 	.long _sys_fanotify_init
 	.long _sys_fanotify_mark
 	.long _sys_prlimit64
+	.long _sys_cacheflush
 
 	.rept NR_syscalls-(.-_sys_call_table)/4
 	.long _sys_ni_syscall

arch/blackfin/mach-common/interrupt.S

@@ -116,7 +116,24 @@ __common_int_entry:
 	cc = r0 == 0;
 	if cc jump .Lcommon_restore_context;
 #else /* CONFIG_IPIPE */
+
+#ifdef CONFIG_PREEMPT
+	r7 = sp;
+	r4.l = lo(ALIGN_PAGE_MASK);
+	r4.h = hi(ALIGN_PAGE_MASK);
+	r7 = r7 & r4;
+	p5 = r7;
+	r7 = [p5 + TI_PREEMPT]; /* get preempt count */
+	r7 += 1;                /* increment it */
+	[p5 + TI_PREEMPT] = r7;
+#endif
 	pseudo_long_call _do_irq, p2;
+
+#ifdef CONFIG_PREEMPT
+	r7 += -1;
+	[p5 + TI_PREEMPT] = r7; /* restore preempt count */
+#endif
+
 	SP += 12;
 #endif /* CONFIG_IPIPE */
 	pseudo_long_call _return_from_int, p2;

arch/blackfin/mach-common/ints-priority.c

@@ -511,7 +511,7 @@ static void bfin_demux_mac_status_irq(unsigned int int_err_irq,
 	int i, irq = 0;
 	u32 status = bfin_read_EMAC_SYSTAT();
 
-	for (i = 0; i < (IRQ_MAC_STMDONE - IRQ_MAC_PHYINT); i++)
+	for (i = 0; i <= (IRQ_MAC_STMDONE - IRQ_MAC_PHYINT); i++)
 		if (status & (1L << i)) {
 			irq = IRQ_MAC_PHYINT + i;
 			break;
@@ -529,8 +529,9 @@ static void bfin_demux_mac_status_irq(unsigned int int_err_irq,
 	} else
 		printk(KERN_ERR
 		       "%s : %s : LINE %d :\nIRQ ?: MAC ERROR"
-		       " INTERRUPT ASSERTED BUT NO SOURCE FOUND\n",
-		       __func__, __FILE__, __LINE__);
+		       " INTERRUPT ASSERTED BUT NO SOURCE FOUND"
+		       "(EMAC_SYSTAT=0x%X)\n",
+		       __func__, __FILE__, __LINE__, status);
 }
 #endif
 
@@ -1298,7 +1299,7 @@ void do_irq(int vec, struct pt_regs *fp)
 	} else {
 		struct ivgx *ivg = ivg7_13[vec - IVG7].ifirst;
 		struct ivgx *ivg_stop = ivg7_13[vec - IVG7].istop;
-#if defined(SIC_ISR0) || defined(SICA_ISR0)
+#if defined(SIC_ISR0)
 		unsigned long sic_status[3];
 
 		if (smp_processor_id()) {
@@ -1378,7 +1379,7 @@ asmlinkage int __ipipe_grab_irq(int vec, struct pt_regs *regs)
 	if (likely(vec == EVT_IVTMR_P))
 		irq = IRQ_CORETMR;
 	else {
-#if defined(SIC_ISR0) || defined(SICA_ISR0)
+#if defined(SIC_ISR0)
 		unsigned long sic_status[3];
 
 		sic_status[0] = bfin_read_SIC_ISR0() & bfin_read_SIC_IMASK0();

arch/blackfin/mm/init.c

@@ -158,5 +158,8 @@ void __init_refok free_initmem(void)
 	free_init_pages("unused kernel memory",
 			(unsigned long)(&__init_begin),
 			(unsigned long)(&__init_end));
+
+	if (memory_start == (unsigned long)(&__init_end))
+		memory_start = (unsigned long)(&__init_begin);
 #endif
 }