|
|
@@ -84,76 +84,76 @@ struct il_priv;
|
|
|
#define IL_MAX_RATES (IL_CCK_RATES + IL_OFDM_RATES)
|
|
|
|
|
|
enum {
|
|
|
- REPLY_ALIVE = 0x1,
|
|
|
- REPLY_ERROR = 0x2,
|
|
|
+ N_ALIVE = 0x1,
|
|
|
+ N_ERROR = 0x2,
|
|
|
|
|
|
/* RXON and QOS commands */
|
|
|
- REPLY_RXON = 0x10,
|
|
|
- REPLY_RXON_ASSOC = 0x11,
|
|
|
- REPLY_QOS_PARAM = 0x13,
|
|
|
- REPLY_RXON_TIMING = 0x14,
|
|
|
+ C_RXON = 0x10,
|
|
|
+ C_RXON_ASSOC = 0x11,
|
|
|
+ C_QOS_PARAM = 0x13,
|
|
|
+ C_RXON_TIMING = 0x14,
|
|
|
|
|
|
/* Multi-Station support */
|
|
|
- REPLY_ADD_STA = 0x18,
|
|
|
- REPLY_REMOVE_STA = 0x19,
|
|
|
+ C_ADD_STA = 0x18,
|
|
|
+ C_REM_STA = 0x19,
|
|
|
|
|
|
/* Security */
|
|
|
- REPLY_WEPKEY = 0x20,
|
|
|
+ C_WEPKEY = 0x20,
|
|
|
|
|
|
/* RX, TX, LEDs */
|
|
|
- REPLY_3945_RX = 0x1b, /* 3945 only */
|
|
|
- REPLY_TX = 0x1c,
|
|
|
- REPLY_RATE_SCALE = 0x47, /* 3945 only */
|
|
|
- REPLY_LEDS_CMD = 0x48,
|
|
|
- REPLY_TX_LINK_QUALITY_CMD = 0x4e, /* for 4965 and up */
|
|
|
+ N_3945_RX = 0x1b, /* 3945 only */
|
|
|
+ C_TX = 0x1c,
|
|
|
+ C_RATE_SCALE = 0x47, /* 3945 only */
|
|
|
+ C_LEDS = 0x48,
|
|
|
+ C_TX_LINK_QUALITY_CMD = 0x4e, /* for 4965 */
|
|
|
|
|
|
/* 802.11h related */
|
|
|
- REPLY_CHANNEL_SWITCH = 0x72,
|
|
|
- CHANNEL_SWITCH_NOTIFICATION = 0x73,
|
|
|
- REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74,
|
|
|
- SPECTRUM_MEASURE_NOTIFICATION = 0x75,
|
|
|
+ C_CHANNEL_SWITCH = 0x72,
|
|
|
+ N_CHANNEL_SWITCH = 0x73,
|
|
|
+ C_SPECTRUM_MEASUREMENT = 0x74,
|
|
|
+ N_SPECTRUM_MEASUREMENT = 0x75,
|
|
|
|
|
|
/* Power Management */
|
|
|
- POWER_TBL_CMD = 0x77,
|
|
|
- PM_SLEEP_NOTIFICATION = 0x7A,
|
|
|
- PM_DEBUG_STATISTIC_NOTIFIC = 0x7B,
|
|
|
+ C_POWER_TBL = 0x77,
|
|
|
+ N_PM_SLEEP = 0x7A,
|
|
|
+ N_PM_DEBUG_STATS = 0x7B,
|
|
|
|
|
|
/* Scan commands and notifications */
|
|
|
- REPLY_SCAN_CMD = 0x80,
|
|
|
- REPLY_SCAN_ABORT_CMD = 0x81,
|
|
|
- SCAN_START_NOTIFICATION = 0x82,
|
|
|
- SCAN_RESULTS_NOTIFICATION = 0x83,
|
|
|
- SCAN_COMPLETE_NOTIFICATION = 0x84,
|
|
|
+ C_SCAN = 0x80,
|
|
|
+ C_SCAN_ABORT = 0x81,
|
|
|
+ N_SCAN_START = 0x82,
|
|
|
+ N_SCAN_RESULTS = 0x83,
|
|
|
+ N_SCAN_COMPLETE = 0x84,
|
|
|
|
|
|
/* IBSS/AP commands */
|
|
|
- BEACON_NOTIFICATION = 0x90,
|
|
|
- REPLY_TX_BEACON = 0x91,
|
|
|
+ N_BEACON = 0x90,
|
|
|
+ C_TX_BEACON= 0x91,
|
|
|
|
|
|
/* Miscellaneous commands */
|
|
|
- REPLY_TX_PWR_TBL_CMD = 0x97,
|
|
|
+ C_TX_PWR_TBL = 0x97,
|
|
|
|
|
|
/* Bluetooth device coexistence config command */
|
|
|
- REPLY_BT_CONFIG = 0x9b,
|
|
|
+ C_BT_CONFIG = 0x9b,
|
|
|
|
|
|
/* Statistics */
|
|
|
- REPLY_STATS_CMD = 0x9c,
|
|
|
- STATS_NOTIFICATION = 0x9d,
|
|
|
+ C_STATS = 0x9c,
|
|
|
+ N_STATS = 0x9d,
|
|
|
|
|
|
/* RF-KILL commands and notifications */
|
|
|
- CARD_STATE_NOTIFICATION = 0xa1,
|
|
|
+ N_CARD_STATE = 0xa1,
|
|
|
|
|
|
/* Missed beacons notification */
|
|
|
- MISSED_BEACONS_NOTIFICATION = 0xa2,
|
|
|
+ N_MISSED_BEACONS = 0xa2,
|
|
|
|
|
|
- REPLY_CT_KILL_CONFIG_CMD = 0xa4,
|
|
|
- SENSITIVITY_CMD = 0xa8,
|
|
|
- REPLY_PHY_CALIBRATION_CMD = 0xb0,
|
|
|
- REPLY_RX_PHY_CMD = 0xc0,
|
|
|
- REPLY_RX_MPDU_CMD = 0xc1,
|
|
|
- REPLY_RX = 0xc3,
|
|
|
- REPLY_COMPRESSED_BA = 0xc5,
|
|
|
+ C_CT_KILL_CONFIG = 0xa4,
|
|
|
+ C_SENSITIVITY = 0xa8,
|
|
|
+ C_PHY_CALIBRATION = 0xb0,
|
|
|
+ N_RX_PHY = 0xc0,
|
|
|
+ N_RX_MPDU = 0xc1,
|
|
|
+ N_RX = 0xc3,
|
|
|
+ N_COMPRESSED_BA = 0xc5,
|
|
|
|
|
|
- REPLY_MAX = 0xff
|
|
|
+ IL_CN_MAX = 0xff
|
|
|
};
|
|
|
|
|
|
/******************************************************************************
|
|
|
@@ -180,7 +180,7 @@ enum {
|
|
|
* driver, and each response/notification received from uCode.
|
|
|
*/
|
|
|
struct il_cmd_header {
|
|
|
- u8 cmd; /* Command ID: REPLY_RXON, etc. */
|
|
|
+ u8 cmd; /* Command ID: C_RXON, etc. */
|
|
|
u8 flags; /* 0:5 reserved, 6 abort, 7 internal */
|
|
|
/*
|
|
|
* The driver sets up the sequence number to values of its choosing.
|
|
|
@@ -192,7 +192,7 @@ struct il_cmd_header {
|
|
|
* There is one exception: uCode sets bit 15 when it originates
|
|
|
* the response/notification, i.e. when the response/notification
|
|
|
* is not a direct response to a command sent by the driver. For
|
|
|
- * example, uCode issues REPLY_3945_RX when it sends a received frame
|
|
|
+ * example, uCode issues N_3945_RX when it sends a received frame
|
|
|
* to the driver; it is not a direct response to any driver command.
|
|
|
*
|
|
|
* The Linux driver uses the following format:
|
|
|
@@ -214,7 +214,7 @@ struct il_cmd_header {
|
|
|
/**
|
|
|
* struct il3945_tx_power
|
|
|
*
|
|
|
- * Used in REPLY_TX_PWR_TBL_CMD, REPLY_SCAN_CMD, REPLY_CHANNEL_SWITCH
|
|
|
+ * Used in C_TX_PWR_TBL, C_SCAN, C_CHANNEL_SWITCH
|
|
|
*
|
|
|
* Each entry contains two values:
|
|
|
* 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
|
|
|
@@ -233,7 +233,7 @@ struct il3945_tx_power {
|
|
|
/**
|
|
|
* struct il3945_power_per_rate
|
|
|
*
|
|
|
- * Used in REPLY_TX_PWR_TBL_CMD, REPLY_CHANNEL_SWITCH
|
|
|
+ * Used in C_TX_PWR_TBL, C_CHANNEL_SWITCH
|
|
|
*/
|
|
|
struct il3945_power_per_rate {
|
|
|
u8 rate; /* plcp */
|
|
|
@@ -245,10 +245,10 @@ struct il3945_power_per_rate {
|
|
|
* iwl4965 rate_n_flags bit fields
|
|
|
*
|
|
|
* rate_n_flags format is used in following iwl4965 commands:
|
|
|
- * REPLY_RX (response only)
|
|
|
- * REPLY_RX_MPDU (response only)
|
|
|
- * REPLY_TX (both command and response)
|
|
|
- * REPLY_TX_LINK_QUALITY_CMD
|
|
|
+ * N_RX (response only)
|
|
|
+ * N_RX_MPDU (response only)
|
|
|
+ * C_TX (both command and response)
|
|
|
+ * C_TX_LINK_QUALITY_CMD
|
|
|
*
|
|
|
* High-throughput (HT) rate format for bits 7:0 (bit 8 must be "1"):
|
|
|
* 2-0: 0) 6 Mbps
|
|
|
@@ -336,7 +336,7 @@ struct il3945_power_per_rate {
|
|
|
/**
|
|
|
* union il4965_tx_power_dual_stream
|
|
|
*
|
|
|
- * Host format used for REPLY_TX_PWR_TBL_CMD, REPLY_CHANNEL_SWITCH
|
|
|
+ * Host format used for C_TX_PWR_TBL, C_CHANNEL_SWITCH
|
|
|
* Use __le32 version (struct tx_power_dual_stream) when building command.
|
|
|
*
|
|
|
* Driver provides radio gain and DSP attenuation settings to device in pairs,
|
|
|
@@ -360,7 +360,7 @@ union il4965_tx_power_dual_stream {
|
|
|
/**
|
|
|
* struct tx_power_dual_stream
|
|
|
*
|
|
|
- * Table entries in REPLY_TX_PWR_TBL_CMD, REPLY_CHANNEL_SWITCH
|
|
|
+ * Table entries in C_TX_PWR_TBL, C_CHANNEL_SWITCH
|
|
|
*
|
|
|
* Same format as il_tx_power_dual_stream, but __le32
|
|
|
*/
|
|
|
@@ -371,7 +371,7 @@ struct tx_power_dual_stream {
|
|
|
/**
|
|
|
* struct il4965_tx_power_db
|
|
|
*
|
|
|
- * Entire table within REPLY_TX_PWR_TBL_CMD, REPLY_CHANNEL_SWITCH
|
|
|
+ * Entire table within C_TX_PWR_TBL, C_CHANNEL_SWITCH
|
|
|
*/
|
|
|
struct il4965_tx_power_db {
|
|
|
struct tx_power_dual_stream power_tbl[POWER_TBL_NUM_ENTRIES];
|
|
|
@@ -387,7 +387,7 @@ struct il4965_tx_power_db {
|
|
|
#define INITIALIZE_SUBTYPE (9)
|
|
|
|
|
|
/*
|
|
|
- * ("Initialize") REPLY_ALIVE = 0x1 (response only, not a command)
|
|
|
+ * ("Initialize") N_ALIVE = 0x1 (response only, not a command)
|
|
|
*
|
|
|
* uCode issues this "initialize alive" notification once the initialization
|
|
|
* uCode image has completed its work, and is ready to load the runtime image.
|
|
|
@@ -435,7 +435,7 @@ struct il_init_alive_resp {
|
|
|
|
|
|
|
|
|
/**
|
|
|
- * REPLY_ALIVE = 0x1 (response only, not a command)
|
|
|
+ * N_ALIVE = 0x1 (response only, not a command)
|
|
|
*
|
|
|
* uCode issues this "alive" notification once the runtime image is ready
|
|
|
* to receive commands from the driver. This is the *second* "alive"
|
|
|
@@ -526,7 +526,7 @@ struct il_alive_resp {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_ERROR = 0x2 (response only, not a command)
|
|
|
+ * N_ERROR = 0x2 (response only, not a command)
|
|
|
*/
|
|
|
struct il_error_resp {
|
|
|
__le32 error_type;
|
|
|
@@ -640,7 +640,7 @@ enum {
|
|
|
#define RXON_FILTER_BCON_AWARE_MSK cpu_to_le32(1 << 6)
|
|
|
|
|
|
/**
|
|
|
- * REPLY_RXON = 0x10 (command, has simple generic response)
|
|
|
+ * C_RXON = 0x10 (command, has simple generic response)
|
|
|
*
|
|
|
* RXON tunes the radio tuner to a service channel, and sets up a number
|
|
|
* of parameters that are used primarily for Rx, but also for Tx operations.
|
|
|
@@ -653,7 +653,7 @@ enum {
|
|
|
* channel.
|
|
|
*
|
|
|
* NOTE: All RXONs wipe clean the internal txpower table. Driver must
|
|
|
- * issue a new REPLY_TX_PWR_TBL_CMD after each REPLY_RXON (0x10),
|
|
|
+ * issue a new C_TX_PWR_TBL after each C_RXON (0x10),
|
|
|
* regardless of whether RXON_FILTER_ASSOC_MSK is set.
|
|
|
*/
|
|
|
|
|
|
@@ -723,7 +723,7 @@ struct il_rxon_cmd {
|
|
|
|
|
|
|
|
|
/*
|
|
|
- * REPLY_RXON_ASSOC = 0x11 (command, has simple generic response)
|
|
|
+ * C_RXON_ASSOC = 0x11 (command, has simple generic response)
|
|
|
*/
|
|
|
struct il3945_rxon_assoc_cmd {
|
|
|
__le32 flags;
|
|
|
@@ -749,7 +749,7 @@ struct il4965_rxon_assoc_cmd {
|
|
|
#define IL39_MAX_UCODE_BEACON_INTERVAL 1 /* 1024 */
|
|
|
|
|
|
/*
|
|
|
- * REPLY_RXON_TIMING = 0x14 (command, has simple generic response)
|
|
|
+ * C_RXON_TIMING = 0x14 (command, has simple generic response)
|
|
|
*/
|
|
|
struct il_rxon_time_cmd {
|
|
|
__le64 timestamp;
|
|
|
@@ -762,7 +762,7 @@ struct il_rxon_time_cmd {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_CHANNEL_SWITCH = 0x72 (command, has simple generic response)
|
|
|
+ * C_CHANNEL_SWITCH = 0x72 (command, has simple generic response)
|
|
|
*/
|
|
|
struct il3945_channel_switch_cmd {
|
|
|
u8 band;
|
|
|
@@ -785,7 +785,7 @@ struct il4965_channel_switch_cmd {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * CHANNEL_SWITCH_NOTIFICATION = 0x73 (notification only, not a command)
|
|
|
+ * N_CHANNEL_SWITCH = 0x73 (notification only, not a command)
|
|
|
*/
|
|
|
struct il_csa_notification {
|
|
|
__le16 band;
|
|
|
@@ -800,7 +800,7 @@ struct il_csa_notification {
|
|
|
*****************************************************************************/
|
|
|
|
|
|
/**
|
|
|
- * struct il_ac_qos -- QOS timing params for REPLY_QOS_PARAM
|
|
|
+ * struct il_ac_qos -- QOS timing params for C_QOS_PARAM
|
|
|
* One for each of 4 EDCA access categories in struct il_qosparam_cmd
|
|
|
*
|
|
|
* @cw_min: Contention win, start value in numbers of slots.
|
|
|
@@ -832,7 +832,7 @@ struct il_ac_qos {
|
|
|
#define AC_NUM 4
|
|
|
|
|
|
/*
|
|
|
- * REPLY_QOS_PARAM = 0x13 (command, has simple generic response)
|
|
|
+ * C_QOS_PARAM = 0x13 (command, has simple generic response)
|
|
|
*
|
|
|
* This command sets up timings for each of the 4 prioritized EDCA Tx FIFOs
|
|
|
* 0: Background, 1: Best Effort, 2: Video, 3: Voice.
|
|
|
@@ -936,15 +936,15 @@ struct sta_id_modify {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_ADD_STA = 0x18 (command)
|
|
|
+ * C_ADD_STA = 0x18 (command)
|
|
|
*
|
|
|
* The device contains an internal table of per-station information,
|
|
|
* with info on security keys, aggregation parameters, and Tx rates for
|
|
|
* initial Tx attempt and any retries (4965 devices uses
|
|
|
- * REPLY_TX_LINK_QUALITY_CMD,
|
|
|
- * 3945 uses REPLY_RATE_SCALE to set up rate tables).
|
|
|
+ * C_TX_LINK_QUALITY_CMD,
|
|
|
+ * 3945 uses C_RATE_SCALE to set up rate tables).
|
|
|
*
|
|
|
- * REPLY_ADD_STA sets up the table entry for one station, either creating
|
|
|
+ * C_ADD_STA sets up the table entry for one station, either creating
|
|
|
* a new entry, or modifying a pre-existing one.
|
|
|
*
|
|
|
* NOTE: RXON command (without "associated" bit set) wipes the station table
|
|
|
@@ -1071,7 +1071,7 @@ struct il_addsta_cmd {
|
|
|
#define ADD_STA_NO_BLOCK_ACK_RESOURCE 0x4
|
|
|
#define ADD_STA_MODIFY_NON_EXIST_STA 0x8
|
|
|
/*
|
|
|
- * REPLY_ADD_STA = 0x18 (response)
|
|
|
+ * C_ADD_STA = 0x18 (response)
|
|
|
*/
|
|
|
struct il_add_sta_resp {
|
|
|
u8 status; /* ADD_STA_* */
|
|
|
@@ -1079,14 +1079,14 @@ struct il_add_sta_resp {
|
|
|
|
|
|
#define REM_STA_SUCCESS_MSK 0x1
|
|
|
/*
|
|
|
- * REPLY_REM_STA = 0x19 (response)
|
|
|
+ * C_REM_STA = 0x19 (response)
|
|
|
*/
|
|
|
struct il_rem_sta_resp {
|
|
|
u8 status;
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_REM_STA = 0x19 (command)
|
|
|
+ * C_REM_STA = 0x19 (command)
|
|
|
*/
|
|
|
struct il_rem_sta_cmd {
|
|
|
u8 num_sta; /* number of removed stations */
|
|
|
@@ -1195,7 +1195,7 @@ struct il3945_rx_frame_end {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_3945_RX = 0x1b (response only, not a command)
|
|
|
+ * N_3945_RX = 0x1b (response only, not a command)
|
|
|
*
|
|
|
* NOTE: DO NOT dereference from casts to this structure
|
|
|
* It is provided only for calculating minimum data set size.
|
|
|
@@ -1226,7 +1226,7 @@ struct il4965_rx_non_cfg_phy {
|
|
|
|
|
|
|
|
|
/*
|
|
|
- * REPLY_RX = 0xc3 (response only, not a command)
|
|
|
+ * N_RX = 0xc3 (response only, not a command)
|
|
|
* Used only for legacy (non 11n) frames.
|
|
|
*/
|
|
|
struct il_rx_phy_res {
|
|
|
@@ -1254,7 +1254,7 @@ struct il_rx_mpdu_res_start {
|
|
|
* (5)
|
|
|
* Tx Commands & Responses:
|
|
|
*
|
|
|
- * Driver must place each REPLY_TX command into one of the prioritized Tx
|
|
|
+ * Driver must place each C_TX command into one of the prioritized Tx
|
|
|
* queues in host DRAM, shared between driver and device (see comments for
|
|
|
* SCD registers and Tx/Rx Queues). When the device's Tx scheduler and uCode
|
|
|
* are preparing to transmit, the device pulls the Tx command over the PCI
|
|
|
@@ -1264,18 +1264,18 @@ struct il_rx_mpdu_res_start {
|
|
|
* uCode handles all timing and protocol related to control frames
|
|
|
* (RTS/CTS/ACK), based on flags in the Tx command. uCode and Tx scheduler
|
|
|
* handle reception of block-acks; uCode updates the host driver via
|
|
|
- * REPLY_COMPRESSED_BA.
|
|
|
+ * N_COMPRESSED_BA.
|
|
|
*
|
|
|
* uCode handles retrying Tx when an ACK is expected but not received.
|
|
|
* This includes trying lower data rates than the one requested in the Tx
|
|
|
- * command, as set up by the REPLY_RATE_SCALE (for 3945) or
|
|
|
- * REPLY_TX_LINK_QUALITY_CMD (4965).
|
|
|
+ * command, as set up by the C_RATE_SCALE (for 3945) or
|
|
|
+ * C_TX_LINK_QUALITY_CMD (4965).
|
|
|
*
|
|
|
- * Driver sets up transmit power for various rates via REPLY_TX_PWR_TBL_CMD.
|
|
|
+ * Driver sets up transmit power for various rates via C_TX_PWR_TBL.
|
|
|
* This command must be executed after every RXON command, before Tx can occur.
|
|
|
*****************************************************************************/
|
|
|
|
|
|
-/* REPLY_TX Tx flags field */
|
|
|
+/* C_TX Tx flags field */
|
|
|
|
|
|
/*
|
|
|
* 1: Use Request-To-Send protocol before this frame.
|
|
|
@@ -1296,7 +1296,7 @@ struct il_rx_mpdu_res_start {
|
|
|
#define TX_CMD_FLG_ACK_MSK cpu_to_le32(1 << 3)
|
|
|
|
|
|
/* For 4965 devices:
|
|
|
- * 1: Use rate scale table (see REPLY_TX_LINK_QUALITY_CMD).
|
|
|
+ * 1: Use rate scale table (see C_TX_LINK_QUALITY_CMD).
|
|
|
* Tx command's initial_rate_idx indicates first rate to try;
|
|
|
* uCode walks through table for additional Tx attempts.
|
|
|
* 0: Use Tx rate/MCS from Tx command's rate_n_flags field.
|
|
|
@@ -1322,7 +1322,7 @@ struct il_rx_mpdu_res_start {
|
|
|
/* 1: uCode overrides sequence control field in MAC header.
|
|
|
* 0: Driver provides sequence control field in MAC header.
|
|
|
* Set this for management frames, non-QOS data frames, non-unicast frames,
|
|
|
- * and also in Tx command embedded in REPLY_SCAN_CMD for active scans. */
|
|
|
+ * and also in Tx command embedded in C_SCAN for active scans. */
|
|
|
#define TX_CMD_FLG_SEQ_CTL_MSK cpu_to_le32(1 << 13)
|
|
|
|
|
|
/* 1: This frame is non-last MPDU; more fragments are coming.
|
|
|
@@ -1369,7 +1369,7 @@ struct il_rx_mpdu_res_start {
|
|
|
#define TKIP_ICV_LEN 4
|
|
|
|
|
|
/*
|
|
|
- * REPLY_TX = 0x1c (command)
|
|
|
+ * C_TX = 0x1c (command)
|
|
|
*/
|
|
|
|
|
|
struct il3945_tx_cmd {
|
|
|
@@ -1434,7 +1434,7 @@ struct il3945_tx_cmd {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_TX = 0x1c (response)
|
|
|
+ * C_TX = 0x1c (response)
|
|
|
*/
|
|
|
struct il3945_tx_resp {
|
|
|
u8 failure_rts;
|
|
|
@@ -1493,7 +1493,7 @@ struct il_tx_cmd {
|
|
|
u8 sec_ctl; /* TX_CMD_SEC_* */
|
|
|
|
|
|
/*
|
|
|
- * Index into rate table (see REPLY_TX_LINK_QUALITY_CMD) for initial
|
|
|
+ * Index into rate table (see C_TX_LINK_QUALITY_CMD) for initial
|
|
|
* Tx attempt, if TX_CMD_FLG_STA_RATE_MSK is set. Normally "0" for
|
|
|
* data frames, this field may be used to selectively reduce initial
|
|
|
* rate (via non-0 value) for special frames (e.g. management), while
|
|
|
@@ -1671,7 +1671,7 @@ enum {
|
|
|
#define AGG_TX_STATE_SEQ_NUM_MSK 0xffff0000
|
|
|
|
|
|
/*
|
|
|
- * REPLY_TX = 0x1c (response)
|
|
|
+ * C_TX = 0x1c (response)
|
|
|
*
|
|
|
* This response may be in one of two slightly different formats, indicated
|
|
|
* by the frame_count field:
|
|
|
@@ -1735,7 +1735,7 @@ struct il4965_tx_resp {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_COMPRESSED_BA = 0xc5 (response only, not a command)
|
|
|
+ * N_COMPRESSED_BA = 0xc5 (response only, not a command)
|
|
|
*
|
|
|
* Reports Block-Acknowledge from recipient station
|
|
|
*/
|
|
|
@@ -1754,7 +1754,7 @@ struct il_compressed_ba_resp {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_TX_PWR_TBL_CMD = 0x97 (command, has simple generic response)
|
|
|
+ * C_TX_PWR_TBL = 0x97 (command, has simple generic response)
|
|
|
*
|
|
|
* See details under "TXPOWER" in 4965.h.
|
|
|
*/
|
|
|
@@ -1777,7 +1777,7 @@ struct il4965_txpowertable_cmd {
|
|
|
/**
|
|
|
* struct il3945_rate_scaling_cmd - Rate Scaling Command & Response
|
|
|
*
|
|
|
- * REPLY_RATE_SCALE = 0x47 (command, has simple generic response)
|
|
|
+ * C_RATE_SCALE = 0x47 (command, has simple generic response)
|
|
|
*
|
|
|
* NOTE: The table of rates passed to the uCode via the
|
|
|
* RATE_SCALE command sets up the corresponding order of
|
|
|
@@ -1786,7 +1786,7 @@ struct il4965_txpowertable_cmd {
|
|
|
*
|
|
|
* For example, if you set 9MB (PLCP 0x0f) as the first
|
|
|
* rate in the rate table, the bit mask for that rate
|
|
|
- * when passed through ofdm_basic_rates on the REPLY_RXON
|
|
|
+ * when passed through ofdm_basic_rates on the C_RXON
|
|
|
* command would be bit 0 (1 << 0)
|
|
|
*/
|
|
|
struct il3945_rate_scaling_info {
|
|
|
@@ -1820,7 +1820,7 @@ struct il3945_rate_scaling_cmd {
|
|
|
/**
|
|
|
* struct il_link_qual_general_params
|
|
|
*
|
|
|
- * Used in REPLY_TX_LINK_QUALITY_CMD
|
|
|
+ * Used in C_TX_LINK_QUALITY_CMD
|
|
|
*/
|
|
|
struct il_link_qual_general_params {
|
|
|
u8 flags;
|
|
|
@@ -1863,7 +1863,7 @@ struct il_link_qual_general_params {
|
|
|
/**
|
|
|
* struct il_link_qual_agg_params
|
|
|
*
|
|
|
- * Used in REPLY_TX_LINK_QUALITY_CMD
|
|
|
+ * Used in C_TX_LINK_QUALITY_CMD
|
|
|
*/
|
|
|
struct il_link_qual_agg_params {
|
|
|
|
|
|
@@ -1892,9 +1892,9 @@ struct il_link_qual_agg_params {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_TX_LINK_QUALITY_CMD = 0x4e (command, has simple generic response)
|
|
|
+ * C_TX_LINK_QUALITY_CMD = 0x4e (command, has simple generic response)
|
|
|
*
|
|
|
- * For 4965 devices only; 3945 uses REPLY_RATE_SCALE.
|
|
|
+ * For 4965 devices only; 3945 uses C_RATE_SCALE.
|
|
|
*
|
|
|
* Each station in the 4965 device's internal station table has its own table
|
|
|
* of 16
|
|
|
@@ -1903,7 +1903,7 @@ struct il_link_qual_agg_params {
|
|
|
* one station.
|
|
|
*
|
|
|
* NOTE: Station must already be in 4965 device's station table.
|
|
|
- * Use REPLY_ADD_STA.
|
|
|
+ * Use C_ADD_STA.
|
|
|
*
|
|
|
* The rate scaling procedures described below work well. Of course, other
|
|
|
* procedures are possible, and may work better for particular environments.
|
|
|
@@ -2117,7 +2117,7 @@ struct il_link_quality_cmd {
|
|
|
#define BT_MAX_KILL_DEF (0x5)
|
|
|
|
|
|
/*
|
|
|
- * REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
|
|
|
+ * C_BT_CONFIG = 0x9b (command, has simple generic response)
|
|
|
*
|
|
|
* 3945 and 4965 devices support hardware handshake with Bluetooth device on
|
|
|
* same platform. Bluetooth device alerts wireless device when it will Tx;
|
|
|
@@ -2159,7 +2159,7 @@ struct il_measure_channel {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (command)
|
|
|
+ * C_SPECTRUM_MEASUREMENT = 0x74 (command)
|
|
|
*/
|
|
|
struct il_spectrum_cmd {
|
|
|
__le16 len; /* number of bytes starting from token */
|
|
|
@@ -2178,7 +2178,7 @@ struct il_spectrum_cmd {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (response)
|
|
|
+ * C_SPECTRUM_MEASUREMENT = 0x74 (response)
|
|
|
*/
|
|
|
struct il_spectrum_resp {
|
|
|
u8 token;
|
|
|
@@ -2228,7 +2228,7 @@ enum il_measure_type {
|
|
|
};
|
|
|
|
|
|
/*
|
|
|
- * SPECTRUM_MEASURE_NOTIFICATION = 0x75 (notification only, not a command)
|
|
|
+ * N_SPECTRUM_MEASUREMENT = 0x75 (notification only, not a command)
|
|
|
*/
|
|
|
struct il_spectrum_notification {
|
|
|
u8 id; /* measurement id -- 0 or 1 */
|
|
|
@@ -2263,7 +2263,7 @@ struct il_spectrum_notification {
|
|
|
* struct il_powertable_cmd - Power Table Command
|
|
|
* @flags: See below:
|
|
|
*
|
|
|
- * POWER_TBL_CMD = 0x77 (command, has simple generic response)
|
|
|
+ * C_POWER_TBL = 0x77 (command, has simple generic response)
|
|
|
*
|
|
|
* PM allow:
|
|
|
* bit 0 - '0' Driver not allow power management
|
|
|
@@ -2318,7 +2318,7 @@ struct il_powertable_cmd {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * PM_SLEEP_NOTIFICATION = 0x7A (notification only, not a command)
|
|
|
+ * N_PM_SLEEP = 0x7A (notification only, not a command)
|
|
|
* all devices identical.
|
|
|
*/
|
|
|
struct il_sleep_notification {
|
|
|
@@ -2346,7 +2346,7 @@ enum {
|
|
|
};
|
|
|
|
|
|
/*
|
|
|
- * CARD_STATE_NOTIFICATION = 0xa1 (notification only, not a command)
|
|
|
+ * N_CARD_STATE = 0xa1 (notification only, not a command)
|
|
|
*/
|
|
|
struct il_card_state_notif {
|
|
|
__le32 flags;
|
|
|
@@ -2373,7 +2373,7 @@ struct il_ct_kill_config {
|
|
|
#define SCAN_CHANNEL_TYPE_ACTIVE cpu_to_le32(1)
|
|
|
|
|
|
/**
|
|
|
- * struct il_scan_channel - entry in REPLY_SCAN_CMD channel table
|
|
|
+ * struct il_scan_channel - entry in C_SCAN channel table
|
|
|
*
|
|
|
* One for each channel in the scan list.
|
|
|
* Each channel can independently select:
|
|
|
@@ -2431,7 +2431,7 @@ struct il_scan_channel {
|
|
|
/**
|
|
|
* struct il_ssid_ie - directed scan network information element
|
|
|
*
|
|
|
- * Up to 20 of these may appear in REPLY_SCAN_CMD (Note: Only 4 are in
|
|
|
+ * Up to 20 of these may appear in C_SCAN (Note: Only 4 are in
|
|
|
* 3945 SCAN api), selected by "type" bit field in struct il_scan_channel;
|
|
|
* each channel may select different ssids from among the 20 (4) entries.
|
|
|
* SSID IEs get transmitted in reverse order of entry.
|
|
|
@@ -2452,7 +2452,7 @@ struct il_ssid_ie {
|
|
|
#define IL_MAX_CMD_SIZE 4096
|
|
|
|
|
|
/*
|
|
|
- * REPLY_SCAN_CMD = 0x80 (command)
|
|
|
+ * C_SCAN = 0x80 (command)
|
|
|
*
|
|
|
* The hardware scan command is very powerful; the driver can set it up to
|
|
|
* maintain (relatively) normal network traffic while doing a scan in the
|
|
|
@@ -2542,7 +2542,7 @@ struct il3945_scan_cmd {
|
|
|
*
|
|
|
* NOTE: Only one band of channels can be scanned per pass. You
|
|
|
* must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
|
|
|
- * for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
|
|
|
+ * for one scan to complete (i.e. receive N_SCAN_COMPLETE)
|
|
|
* before requesting another scan.
|
|
|
*/
|
|
|
u8 data[0];
|
|
|
@@ -2586,7 +2586,7 @@ struct il_scan_cmd {
|
|
|
*
|
|
|
* NOTE: Only one band of channels can be scanned per pass. You
|
|
|
* must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
|
|
|
- * for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
|
|
|
+ * for one scan to complete (i.e. receive N_SCAN_COMPLETE)
|
|
|
* before requesting another scan.
|
|
|
*/
|
|
|
u8 data[0];
|
|
|
@@ -2598,14 +2598,14 @@ struct il_scan_cmd {
|
|
|
#define ABORT_STATUS 0x2
|
|
|
|
|
|
/*
|
|
|
- * REPLY_SCAN_CMD = 0x80 (response)
|
|
|
+ * C_SCAN = 0x80 (response)
|
|
|
*/
|
|
|
struct il_scanreq_notification {
|
|
|
__le32 status; /* 1: okay, 2: cannot fulfill request */
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * SCAN_START_NOTIFICATION = 0x82 (notification only, not a command)
|
|
|
+ * N_SCAN_START = 0x82 (notification only, not a command)
|
|
|
*/
|
|
|
struct il_scanstart_notification {
|
|
|
__le32 tsf_low;
|
|
|
@@ -2628,7 +2628,7 @@ struct il_scanstart_notification {
|
|
|
|
|
|
#define NUMBER_OF_STATS 1 /* first __le32 is good CRC */
|
|
|
/*
|
|
|
- * SCAN_RESULTS_NOTIFICATION = 0x83 (notification only, not a command)
|
|
|
+ * N_SCAN_RESULTS = 0x83 (notification only, not a command)
|
|
|
*/
|
|
|
struct il_scanresults_notification {
|
|
|
u8 channel;
|
|
|
@@ -2641,7 +2641,7 @@ struct il_scanresults_notification {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * SCAN_COMPLETE_NOTIFICATION = 0x84 (notification only, not a command)
|
|
|
+ * N_SCAN_COMPLETE = 0x84 (notification only, not a command)
|
|
|
*/
|
|
|
struct il_scancomplete_notification {
|
|
|
u8 scanned_channels;
|
|
|
@@ -2664,7 +2664,7 @@ enum il_ibss_manager {
|
|
|
};
|
|
|
|
|
|
/*
|
|
|
- * BEACON_NOTIFICATION = 0x90 (notification only, not a command)
|
|
|
+ * N_BEACON = 0x90 (notification only, not a command)
|
|
|
*/
|
|
|
|
|
|
struct il3945_beacon_notif {
|
|
|
@@ -2682,7 +2682,7 @@ struct il4965_beacon_notif {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * REPLY_TX_BEACON = 0x91 (command, has simple generic response)
|
|
|
+ * C_TX_BEACON= 0x91 (command, has simple generic response)
|
|
|
*/
|
|
|
|
|
|
struct il3945_tx_beacon_cmd {
|
|
|
@@ -2963,19 +2963,19 @@ struct stats_general {
|
|
|
#define UCODE_STATS_NARROW_BAND_MSK (0x1 << 2)
|
|
|
|
|
|
/*
|
|
|
- * REPLY_STATS_CMD = 0x9c,
|
|
|
+ * C_STATS = 0x9c,
|
|
|
* all devices identical.
|
|
|
*
|
|
|
* This command triggers an immediate response containing uCode stats.
|
|
|
- * The response is in the same format as STATS_NOTIFICATION 0x9d, below.
|
|
|
+ * The response is in the same format as N_STATS 0x9d, below.
|
|
|
*
|
|
|
* If the CLEAR_STATS configuration flag is set, uCode will clear its
|
|
|
* internal copy of the stats (counters) after issuing the response.
|
|
|
- * This flag does not affect STATS_NOTIFICATIONs after beacons (see below).
|
|
|
+ * This flag does not affect N_STATSs after beacons (see below).
|
|
|
*
|
|
|
* If the DISABLE_NOTIF configuration flag is set, uCode will not issue
|
|
|
- * STATS_NOTIFICATIONs after received beacons (see below). This flag
|
|
|
- * does not affect the response to the REPLY_STATS_CMD 0x9c itself.
|
|
|
+ * N_STATSs after received beacons (see below). This flag
|
|
|
+ * does not affect the response to the C_STATS 0x9c itself.
|
|
|
*/
|
|
|
#define IL_STATS_CONF_CLEAR_STATS cpu_to_le32(0x1) /* see above */
|
|
|
#define IL_STATS_CONF_DISABLE_NOTIF cpu_to_le32(0x2)/* see above */
|
|
|
@@ -2984,14 +2984,14 @@ struct il_stats_cmd {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * STATS_NOTIFICATION = 0x9d (notification only, not a command)
|
|
|
+ * N_STATS = 0x9d (notification only, not a command)
|
|
|
*
|
|
|
* By default, uCode issues this notification after receiving a beacon
|
|
|
* while associated. To disable this behavior, set DISABLE_NOTIF flag in the
|
|
|
- * REPLY_STATS_CMD 0x9c, above.
|
|
|
+ * C_STATS 0x9c, above.
|
|
|
*
|
|
|
* Statistics counters continue to increment beacon after beacon, but are
|
|
|
- * cleared when changing channels or when driver issues REPLY_STATS_CMD
|
|
|
+ * cleared when changing channels or when driver issues C_STATS
|
|
|
* 0x9c with CLEAR_STATS bit set (see above).
|
|
|
*
|
|
|
* uCode also issues this notification during scans. uCode clears stats
|
|
|
@@ -3016,9 +3016,9 @@ struct il_notif_stats {
|
|
|
} __packed;
|
|
|
|
|
|
/*
|
|
|
- * MISSED_BEACONS_NOTIFICATION = 0xa2 (notification only, not a command)
|
|
|
+ * N_MISSED_BEACONS = 0xa2 (notification only, not a command)
|
|
|
*
|
|
|
- * uCode send MISSED_BEACONS_NOTIFICATION to driver when detect beacon missed
|
|
|
+ * uCode send N_MISSED_BEACONS to driver when detect beacon missed
|
|
|
* in regardless of how many missed beacons, which mean when driver receive the
|
|
|
* notification, inside the command, it can find all the beacons information
|
|
|
* which include number of total missed beacons, number of consecutive missed
|
|
|
@@ -3062,7 +3062,7 @@ struct il_missed_beacon_notif {
|
|
|
*****************************************************************************/
|
|
|
|
|
|
/**
|
|
|
- * SENSITIVITY_CMD = 0xa8 (command, has simple generic response)
|
|
|
+ * C_SENSITIVITY = 0xa8 (command, has simple generic response)
|
|
|
*
|
|
|
* This command sets up the Rx signal detector for a sensitivity level that
|
|
|
* is high enough to lock onto all signals within the associated network,
|
|
|
@@ -3076,7 +3076,7 @@ struct il_missed_beacon_notif {
|
|
|
* time listening, not transmitting). Driver must adjust sensitivity so that
|
|
|
* the ratio of actual false alarms to actual Rx time falls within this range.
|
|
|
*
|
|
|
- * While associated, uCode delivers STATS_NOTIFICATIONs after each
|
|
|
+ * While associated, uCode delivers N_STATSs after each
|
|
|
* received beacon. These provide information to the driver to analyze the
|
|
|
* sensitivity. Don't analyze stats that come in from scanning, or any
|
|
|
* other non-associated-network source. Pertinent stats include:
|
|
|
@@ -3217,7 +3217,7 @@ struct il_missed_beacon_notif {
|
|
|
*/
|
|
|
|
|
|
/*
|
|
|
- * Table entries in SENSITIVITY_CMD (struct il_sensitivity_cmd)
|
|
|
+ * Table entries in C_SENSITIVITY (struct il_sensitivity_cmd)
|
|
|
*/
|
|
|
#define HD_TBL_SIZE (11) /* number of entries */
|
|
|
#define HD_MIN_ENERGY_CCK_DET_IDX (0) /* table idxes */
|
|
|
@@ -3233,8 +3233,8 @@ struct il_missed_beacon_notif {
|
|
|
#define HD_OFDM_ENERGY_TH_IN_IDX (10)
|
|
|
|
|
|
/* Control field in struct il_sensitivity_cmd */
|
|
|
-#define SENSITIVITY_CMD_CONTROL_DEFAULT_TBL cpu_to_le16(0)
|
|
|
-#define SENSITIVITY_CMD_CONTROL_WORK_TBL cpu_to_le16(1)
|
|
|
+#define C_SENSITIVITY_CONTROL_DEFAULT_TBL cpu_to_le16(0)
|
|
|
+#define C_SENSITIVITY_CONTROL_WORK_TBL cpu_to_le16(1)
|
|
|
|
|
|
/**
|
|
|
* struct il_sensitivity_cmd
|
|
|
@@ -3250,12 +3250,12 @@ struct il_sensitivity_cmd {
|
|
|
|
|
|
|
|
|
/**
|
|
|
- * REPLY_PHY_CALIBRATION_CMD = 0xb0 (command, has simple generic response)
|
|
|
+ * C_PHY_CALIBRATION = 0xb0 (command, has simple generic response)
|
|
|
*
|
|
|
* This command sets the relative gains of 4965 device's 3 radio receiver chains.
|
|
|
*
|
|
|
* After the first association, driver should accumulate signal and noise
|
|
|
- * stats from the STATS_NOTIFICATIONs that follow the first 20
|
|
|
+ * stats from the N_STATSs that follow the first 20
|
|
|
* beacons from the associated network (don't collect stats that come
|
|
|
* in from scanning, or any other non-network source).
|
|
|
*
|
|
|
@@ -3338,7 +3338,7 @@ struct il_calib_diff_gain_cmd {
|
|
|
|
|
|
/*
|
|
|
* LEDs Command & Response
|
|
|
- * REPLY_LEDS_CMD = 0x48 (command, has simple generic response)
|
|
|
+ * C_LEDS = 0x48 (command, has simple generic response)
|
|
|
*
|
|
|
* For each of 3 possible LEDs (Activity/Link/Tech, selected by "id" field),
|
|
|
* this command turns it on or off, or sets up a periodic blinking cycle.
|
Stanislaw Gruszka