serial: max3107: introduce a max3107 driver

This device is used by some of the Intel MID platforms. It's not similar
enough to the MAX3100 to use the same driver.

At this point the driver is specific to the platform and not generalised.
We will fix that later.

Signed-off-by: jianwei.yang <jianwei.yang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/serial/Kconfig

@@ -542,6 +542,14 @@ config SERIAL_S5PV210
 	help
 	  Serial port support for Samsung's S5P Family of SoC's
 
+config SERIAL_MAX3107
+	tristate "MAX3107 support"
+	depends on SPI && GPIOLIB
+	select SERIAL_CORE
+	default y
+	help
+	  MAX3107 chip support
+
 config SERIAL_MAX3100
 	tristate "MAX3100 support"
 	depends on SPI

drivers/serial/Makefile

@@ -46,6 +46,7 @@ obj-$(CONFIG_SERIAL_S3C24A0) += s3c24a0.o
 obj-$(CONFIG_SERIAL_S3C6400) += s3c6400.o
 obj-$(CONFIG_SERIAL_S5PV210) += s5pv210.o
 obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
+obj-$(CONFIG_SERIAL_MAX3107) += max3107.o
 obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o
 obj-$(CONFIG_SERIAL_MUX) += mux.o
 obj-$(CONFIG_SERIAL_68328) += 68328serial.o

drivers/serial/max3107.c

@@ -0,0 +1,1442 @@
+/*
+ *  max3107.c - spi uart protocol driver for Maxim 3107
+ *  Based on max3100.c
+ *	by Christian Pellegrin <chripell@evolware.org>
+ *  and	max3110.c
+ *	by Feng Tang <feng.tang@intel.com>
+ *
+ *  Copyright (C) Aavamobile 2009
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/spi/spi.h>
+#include <linux/freezer.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/sfi.h>
+#include <asm/mrst.h>
+#include "max3107.h"
+
+struct baud_table {
+	int baud;
+	u32 new_brg;
+};
+
+struct max3107_port {
+	/* UART port structure */
+	struct uart_port port;
+
+	/* SPI device structure */
+	struct spi_device *spi;
+
+	/* GPIO chip stucture */
+	struct gpio_chip chip;
+
+	/* Workqueue that does all the magic */
+	struct workqueue_struct *workqueue;
+	struct work_struct work;
+
+	/* Lock for shared data */
+	spinlock_t data_lock;
+
+	/* Device configuration */
+	int ext_clk;		/* 1 if external clock used */
+	int loopback;		/* Current loopback mode state */
+	int baud;			/* Current baud rate */
+
+	/* State flags */
+	int suspended;		/* Indicates suspend mode */
+	int tx_fifo_empty;	/* Flag for TX FIFO state */
+	int rx_enabled;		/* Flag for receiver state */
+	int tx_enabled;		/* Flag for transmitter state */
+
+	u16 irqen_reg;		/* Current IRQ enable register value */
+	/* Shared data */
+	u16 mode1_reg;		/* Current mode1 register value*/
+	int mode1_commit;	/* Flag for setting new mode1 register value */
+	u16 lcr_reg;		/* Current LCR register value */
+	int lcr_commit;		/* Flag for setting new LCR register value */
+	u32 brg_cfg;		/* Current Baud rate generator config  */
+	int brg_commit;		/* Flag for setting new baud rate generator
+				 * config
+				 */
+	struct baud_table *baud_tbl;
+	int handle_irq;		/* Indicates that IRQ should be handled */
+
+	/* Rx buffer and str*/
+	u16 *rxbuf;
+	u8  *rxstr;
+	/* Tx buffer*/
+	u16 *txbuf;
+};
+
+/* Platform data structure */
+struct max3107_plat {
+	/* Loopback mode enable */
+	int loopback;
+	/* External clock enable */
+	int ext_clk;
+	/* HW suspend function */
+	void (*max3107_hw_suspend) (struct max3107_port *s, int suspend);
+	/* Polling mode enable */
+	int polled_mode;
+	/* Polling period if polling mode enabled */
+	int poll_time;
+};
+
+static struct baud_table brg13_ext[] = {
+	{ 300,    MAX3107_BRG13_B300 },
+	{ 600,    MAX3107_BRG13_B600 },
+	{ 1200,   MAX3107_BRG13_B1200 },
+	{ 2400,   MAX3107_BRG13_B2400 },
+	{ 4800,   MAX3107_BRG13_B4800 },
+	{ 9600,   MAX3107_BRG13_B9600 },
+	{ 19200,  MAX3107_BRG13_B19200 },
+	{ 57600,  MAX3107_BRG13_B57600 },
+	{ 115200, MAX3107_BRG13_B115200 },
+	{ 230400, MAX3107_BRG13_B230400 },
+	{ 460800, MAX3107_BRG13_B460800 },
+	{ 921600, MAX3107_BRG13_B921600 },
+	{ 0, 0 }
+};
+
+static struct baud_table brg26_ext[] = {
+	{ 300,    MAX3107_BRG26_B300 },
+	{ 600,    MAX3107_BRG26_B600 },
+	{ 1200,   MAX3107_BRG26_B1200 },
+	{ 2400,   MAX3107_BRG26_B2400 },
+	{ 4800,   MAX3107_BRG26_B4800 },
+	{ 9600,   MAX3107_BRG26_B9600 },
+	{ 19200,  MAX3107_BRG26_B19200 },
+	{ 57600,  MAX3107_BRG26_B57600 },
+	{ 115200, MAX3107_BRG26_B115200 },
+	{ 230400, MAX3107_BRG26_B230400 },
+	{ 460800, MAX3107_BRG26_B460800 },
+	{ 921600, MAX3107_BRG26_B921600 },
+	{ 0, 0 }
+};
+
+static struct baud_table brg13_int[] = {
+	{ 300,    MAX3107_BRG13_IB300 },
+	{ 600,    MAX3107_BRG13_IB600 },
+	{ 1200,   MAX3107_BRG13_IB1200 },
+	{ 2400,   MAX3107_BRG13_IB2400 },
+	{ 4800,   MAX3107_BRG13_IB4800 },
+	{ 9600,   MAX3107_BRG13_IB9600 },
+	{ 19200,  MAX3107_BRG13_IB19200 },
+	{ 57600,  MAX3107_BRG13_IB57600 },
+	{ 115200, MAX3107_BRG13_IB115200 },
+	{ 230400, MAX3107_BRG13_IB230400 },
+	{ 460800, MAX3107_BRG13_IB460800 },
+	{ 921600, MAX3107_BRG13_IB921600 },
+	{ 0, 0 }
+};
+
+static u32 get_new_brg(int baud, struct max3107_port *s)
+{
+	int i;
+	struct baud_table *baud_tbl = s->baud_tbl;
+
+	for (i = 0; i < 13; i++) {
+		if (baud == baud_tbl[i].baud)
+			return baud_tbl[i].new_brg;
+	}
+
+	return 0;
+}
+
+/* Perform SPI transfer for write/read of device register(s) */
+static int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len)
+{
+	struct spi_message spi_msg;
+	struct spi_transfer spi_xfer;
+
+	/* Initialize SPI ,message */
+	spi_message_init(&spi_msg);
+
+	/* Initialize SPI transfer */
+	memset(&spi_xfer, 0, sizeof spi_xfer);
+	spi_xfer.len = len;
+	spi_xfer.tx_buf = tx;
+	spi_xfer.rx_buf = rx;
+	spi_xfer.speed_hz = MAX3107_SPI_SPEED;
+
+	/* Add SPI transfer to SPI message */
+	spi_message_add_tail(&spi_xfer, &spi_msg);
+
+#ifdef DBG_TRACE_SPI_DATA
+	{
+		int i;
+		pr_info("tx len %d:\n", spi_xfer.len);
+		for (i = 0 ; i < spi_xfer.len && i < 32 ; i++)
+			pr_info(" %x", ((u8 *)spi_xfer.tx_buf)[i]);
+		pr_info("\n");
+	}
+#endif
+
+	/* Perform synchronous SPI transfer */
+	if (spi_sync(s->spi, &spi_msg)) {
+		dev_err(&s->spi->dev, "spi_sync failure\n");
+		return -EIO;
+	}
+
+#ifdef DBG_TRACE_SPI_DATA
+	if (spi_xfer.rx_buf) {
+		int i;
+		pr_info("rx len %d:\n", spi_xfer.len);
+		for (i = 0 ; i < spi_xfer.len && i < 32 ; i++)
+			pr_info(" %x", ((u8 *)spi_xfer.rx_buf)[i]);
+		pr_info("\n");
+	}
+#endif
+	return 0;
+}
+
+/* Puts received data to circular buffer */
+static void put_data_to_circ_buf(struct max3107_port *s, unsigned char *data,
+					int len)
+{
+	struct uart_port *port = &s->port;
+	struct tty_struct *tty;
+
+	if (!port->state)
+		return;
+
+	tty = port->state->port.tty;
+	if (!tty)
+		return;
+
+	/* Insert received data */
+	tty_insert_flip_string(tty, data, len);
+	/* Update RX counter */
+	port->icount.rx += len;
+}
+
+/* Handle data receiving */
+static void max3107_handlerx(struct max3107_port *s, u16 rxlvl)
+{
+	int i;
+	int j;
+	int len;				/* SPI transfer buffer length */
+	u16 *buf;
+	u8 *valid_str;
+
+	if (!s->rx_enabled)
+		/* RX is disabled */
+		return;
+
+	if (rxlvl == 0) {
+		/* RX fifo is empty */
+		return;
+	} else if (rxlvl >= MAX3107_RX_FIFO_SIZE) {
+		dev_warn(&s->spi->dev, "Possible RX FIFO overrun %d\n", rxlvl);
+		/* Ensure sanity of RX level */
+		rxlvl = MAX3107_RX_FIFO_SIZE;
+	}
+	if ((s->rxbuf == 0) || (s->rxstr == 0)) {
+		dev_warn(&s->spi->dev, "Rx buffer/str isn't ready\n");
+		return;
+	}
+	buf = s->rxbuf;
+	valid_str = s->rxstr;
+	while (rxlvl) {
+		pr_debug("rxlvl %d\n", rxlvl);
+		/* Clear buffer */
+		memset(buf, 0, sizeof(u16) * (MAX3107_RX_FIFO_SIZE + 2));
+		len = 0;
+		if (s->irqen_reg & MAX3107_IRQ_RXFIFO_BIT) {
+			/* First disable RX FIFO interrupt */
+			pr_debug("Disabling RX INT\n");
+			buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+			s->irqen_reg &= ~MAX3107_IRQ_RXFIFO_BIT;
+			buf[0] |= s->irqen_reg;
+			len++;
+		}
+		/* Just increase the length by amount of words in FIFO since
+		 * buffer was zeroed and SPI transfer of 0x0000 means reading
+		 * from RX FIFO
+		 */
+		len += rxlvl;
+		/* Append RX level query */
+		buf[len] = MAX3107_RXFIFOLVL_REG;
+		len++;
+
+		/* Perform the SPI transfer */
+		if (max3107_rw(s, (u8 *)buf, (u8 *)buf, len * 2)) {
+			dev_err(&s->spi->dev, "SPI transfer for RX h failed\n");
+			return;
+		}
+
+		/* Skip RX FIFO interrupt disabling word if it was added */
+		j = ((len - 1) - rxlvl);
+		/* Read received words */
+		for (i = 0; i < rxlvl; i++, j++)
+			valid_str[i] = (u8)buf[j];
+		put_data_to_circ_buf(s, valid_str, rxlvl);
+		/* Get new RX level */
+		rxlvl = (buf[len - 1] & MAX3107_SPI_RX_DATA_MASK);
+	}
+
+	if (s->rx_enabled) {
+		/* RX still enabled, re-enable RX FIFO interrupt */
+		pr_debug("Enabling RX INT\n");
+		buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+		s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT;
+		buf[0] |= s->irqen_reg;
+		if (max3107_rw(s, (u8 *)buf, NULL, 2))
+			dev_err(&s->spi->dev, "RX FIFO INT enabling failed\n");
+	}
+
+	/* Push the received data to receivers */
+	if (s->port.state->port.tty)
+		tty_flip_buffer_push(s->port.state->port.tty);
+}
+
+
+/* Handle data sending */
+static void max3107_handletx(struct max3107_port *s)
+{
+	struct circ_buf *xmit = &s->port.state->xmit;
+	int i;
+	unsigned long flags;
+	int len;				/* SPI transfer buffer length */
+	u16 *buf;
+
+	if (!s->tx_fifo_empty)
+		/* Don't send more data before previous data is sent */
+		return;
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port))
+		/* No data to send or TX is stopped */
+		return;
+
+	if (!s->txbuf) {
+		dev_warn(&s->spi->dev, "Txbuf isn't ready\n");
+		return;
+	}
+	buf = s->txbuf;
+	/* Get length of data pending in circular buffer */
+	len = uart_circ_chars_pending(xmit);
+	if (len) {
+		/* Limit to size of TX FIFO */
+		if (len > MAX3107_TX_FIFO_SIZE)
+			len = MAX3107_TX_FIFO_SIZE;
+
+		pr_debug("txlen %d\n", len);
+
+		/* Update TX counter */
+		s->port.icount.tx += len;
+
+		/* TX FIFO will no longer be empty */
+		s->tx_fifo_empty = 0;
+
+		i = 0;
+		if (s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT) {
+			/* First disable TX empty interrupt */
+			pr_debug("Disabling TE INT\n");
+			buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+			s->irqen_reg &= ~MAX3107_IRQ_TXEMPTY_BIT;
+			buf[i] |= s->irqen_reg;
+			i++;
+			len++;
+		}
+		/* Add data to send */
+		spin_lock_irqsave(&s->port.lock, flags);
+		for ( ; i < len ; i++) {
+			buf[i] = (MAX3107_WRITE_BIT | MAX3107_THR_REG);
+			buf[i] |= ((u16)xmit->buf[xmit->tail] &
+						MAX3107_SPI_TX_DATA_MASK);
+			xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		}
+		spin_unlock_irqrestore(&s->port.lock, flags);
+		if (!(s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT)) {
+			/* Enable TX empty interrupt */
+			pr_debug("Enabling TE INT\n");
+			buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG);
+			s->irqen_reg |= MAX3107_IRQ_TXEMPTY_BIT;
+			buf[i] |= s->irqen_reg;
+			i++;
+			len++;
+		}
+		if (!s->tx_enabled) {
+			/* Enable TX */
+			pr_debug("Enable TX\n");
+			buf[i] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+			spin_lock_irqsave(&s->data_lock, flags);
+			s->mode1_reg &= ~MAX3107_MODE1_TXDIS_BIT;
+			buf[i] |= s->mode1_reg;
+			spin_unlock_irqrestore(&s->data_lock, flags);
+			s->tx_enabled = 1;
+			i++;
+			len++;
+		}
+
+		/* Perform the SPI transfer */
+		if (max3107_rw(s, (u8 *)buf, NULL, len*2)) {
+			dev_err(&s->spi->dev,
+				"SPI transfer TX handling failed\n");
+			return;
+		}
+	}
+
+	/* Indicate wake up if circular buffer is getting low on data */
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(&s->port);
+
+}
+
+/* Handle interrupts
+ * Also reads and returns current RX FIFO level
+ */
+static u16 handle_interrupt(struct max3107_port *s)
+{
+	u16 buf[4];	/* Buffer for SPI transfers */
+	u8 irq_status;
+	u16 rx_level;
+	unsigned long flags;
+
+	/* Read IRQ status register */
+	buf[0] = MAX3107_IRQSTS_REG;
+	/* Read status IRQ status register */
+	buf[1] = MAX3107_STS_IRQSTS_REG;
+	/* Read LSR IRQ status register */
+	buf[2] = MAX3107_LSR_IRQSTS_REG;
+	/* Query RX level */
+	buf[3] = MAX3107_RXFIFOLVL_REG;
+
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 8)) {
+		dev_err(&s->spi->dev,
+			"SPI transfer for INTR handling failed\n");
+		return 0;
+	}
+
+	irq_status = (u8)buf[0];
+	pr_debug("IRQSTS %x\n", irq_status);
+	rx_level = (buf[3] & MAX3107_SPI_RX_DATA_MASK);
+
+	if (irq_status & MAX3107_IRQ_LSR_BIT) {
+		/* LSR interrupt */
+		if (buf[2] & MAX3107_LSR_RXTO_BIT)
+			/* RX timeout interrupt,
+			 * handled by normal RX handling
+			 */
+			pr_debug("RX TO INT\n");
+	}
+
+	if (irq_status & MAX3107_IRQ_TXEMPTY_BIT) {
+		/* Tx empty interrupt,
+		 * disable TX and set tx_fifo_empty flag
+		 */
+		pr_debug("TE INT, disabling TX\n");
+		buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+		spin_lock_irqsave(&s->data_lock, flags);
+		s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT;
+		buf[0] |= s->mode1_reg;
+		spin_unlock_irqrestore(&s->data_lock, flags);
+		if (max3107_rw(s, (u8 *)buf, NULL, 2))
+			dev_err(&s->spi->dev, "SPI transfer TX dis failed\n");
+		s->tx_enabled = 0;
+		s->tx_fifo_empty = 1;
+	}
+
+	if (irq_status & MAX3107_IRQ_RXFIFO_BIT)
+		/* RX FIFO interrupt,
+		 * handled by normal RX handling
+		 */
+		pr_debug("RFIFO INT\n");
+
+	/* Return RX level */
+	return rx_level;
+}
+
+/* Trigger work thread*/
+static void max3107_dowork(struct max3107_port *s)
+{
+	if (!work_pending(&s->work) && !freezing(current) && !s->suspended)
+		queue_work(s->workqueue, &s->work);
+	else
+		dev_warn(&s->spi->dev, "interrup isn't serviced normally!\n");
+}
+
+/* Work thread */
+static void max3107_work(struct work_struct *w)
+{
+	struct max3107_port *s = container_of(w, struct max3107_port, work);
+	u16 rxlvl = 0;
+	int len;	/* SPI transfer buffer length */
+	u16 buf[5];	/* Buffer for SPI transfers */
+	unsigned long flags;
+
+	/* Start by reading current RX FIFO level */
+	buf[0] = MAX3107_RXFIFOLVL_REG;
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
+		dev_err(&s->spi->dev, "SPI transfer RX lev failed\n");
+		rxlvl = 0;
+	} else {
+		rxlvl = (buf[0] & MAX3107_SPI_RX_DATA_MASK);
+	}
+
+	do {
+		pr_debug("rxlvl %d\n", rxlvl);
+
+		/* Handle RX */
+		max3107_handlerx(s, rxlvl);
+		rxlvl = 0;
+
+		if (s->handle_irq) {
+			/* Handle pending interrupts
+			 * We also get new RX FIFO level since new data may
+			 * have been received while pushing received data to
+			 * receivers
+			 */
+			s->handle_irq = 0;
+			rxlvl = handle_interrupt(s);
+		}
+
+		/* Handle TX */
+		max3107_handletx(s);
+
+		/* Handle configuration changes */
+		len = 0;
+		spin_lock_irqsave(&s->data_lock, flags);
+		if (s->mode1_commit) {
+			pr_debug("mode1_commit\n");
+			buf[len] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+			buf[len++] |= s->mode1_reg;
+			s->mode1_commit = 0;
+		}
+		if (s->lcr_commit) {
+			pr_debug("lcr_commit\n");
+			buf[len] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG);
+			buf[len++] |= s->lcr_reg;
+			s->lcr_commit = 0;
+		}
+		if (s->brg_commit) {
+			pr_debug("brg_commit\n");
+			buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG);
+			buf[len++] |= ((s->brg_cfg >> 16) &
+						MAX3107_SPI_TX_DATA_MASK);
+			buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG);
+			buf[len++] |= ((s->brg_cfg >> 8) &
+						MAX3107_SPI_TX_DATA_MASK);
+			buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG);
+			buf[len++] |= ((s->brg_cfg) & 0xff);
+			s->brg_commit = 0;
+		}
+		spin_unlock_irqrestore(&s->data_lock, flags);
+
+		if (len > 0) {
+			if (max3107_rw(s, (u8 *)buf, NULL, len * 2))
+				dev_err(&s->spi->dev,
+					"SPI transfer config failed\n");
+		}
+
+		/* Reloop if interrupt handling indicated data in RX FIFO */
+	} while (rxlvl);
+
+}
+
+/* Set sleep mode */
+static void max3107_set_sleep(struct max3107_port *s, int mode)
+{
+	u16 buf[1];	/* Buffer for SPI transfer */
+	unsigned long flags;
+	pr_debug("enter, mode %d\n", mode);
+
+	buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG);
+	spin_lock_irqsave(&s->data_lock, flags);
+	switch (mode) {
+	case MAX3107_DISABLE_FORCED_SLEEP:
+			s->mode1_reg &= ~MAX3107_MODE1_FORCESLEEP_BIT;
+			break;
+	case MAX3107_ENABLE_FORCED_SLEEP:
+			s->mode1_reg |= MAX3107_MODE1_FORCESLEEP_BIT;
+			break;
+	case MAX3107_DISABLE_AUTOSLEEP:
+			s->mode1_reg &= ~MAX3107_MODE1_AUTOSLEEP_BIT;
+			break;
+	case MAX3107_ENABLE_AUTOSLEEP:
+			s->mode1_reg |= MAX3107_MODE1_AUTOSLEEP_BIT;
+			break;
+	default:
+		spin_unlock_irqrestore(&s->data_lock, flags);
+		dev_warn(&s->spi->dev, "invalid sleep mode\n");
+		return;
+	}
+	buf[0] |= s->mode1_reg;
+	spin_unlock_irqrestore(&s->data_lock, flags);
+
+	if (max3107_rw(s, (u8 *)buf, NULL, 2))
+		dev_err(&s->spi->dev, "SPI transfer sleep mode failed\n");
+
+	if (mode == MAX3107_DISABLE_AUTOSLEEP ||
+			mode == MAX3107_DISABLE_FORCED_SLEEP)
+		msleep(MAX3107_WAKEUP_DELAY);
+}
+
+/* Perform full register initialization */
+static void max3107_register_init(struct max3107_port *s)
+{
+	u16 buf[11];	/* Buffer for SPI transfers */
+
+	/* 1. Configure baud rate, 9600 as default */
+	s->baud = 9600;
+	/* the below is default*/
+	if (s->ext_clk) {
+		s->brg_cfg = MAX3107_BRG26_B9600;
+		s->baud_tbl = (struct baud_table *)brg26_ext;
+	} else {
+		s->brg_cfg = MAX3107_BRG13_IB9600;
+		s->baud_tbl = (struct baud_table *)brg13_int;
+	}
+#if 0
+	/*override for AAVA SC specific*/
+	if (mrst_platform_id() == MRST_PLATFORM_AAVA_SC) {
+		if (get_koski_build_id() <= KOSKI_EV2)
+			if (s->ext_clk) {
+				s->brg_cfg = MAX3107_BRG13_B9600;
+				s->baud_tbl = (struct baud_table *)brg13_ext;
+			}
+	}
+#endif
+	buf[0] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG)
+		| ((s->brg_cfg >> 16) & MAX3107_SPI_TX_DATA_MASK);
+	buf[1] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG)
+		| ((s->brg_cfg >> 8) & MAX3107_SPI_TX_DATA_MASK);
+	buf[2] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG)
+		| ((s->brg_cfg) & 0xff);
+
+	/* 2. Configure LCR register, 8N1 mode by default */
+	s->lcr_reg = MAX3107_LCR_WORD_LEN_8;
+	buf[3] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG)
+		| s->lcr_reg;
+
+	/* 3. Configure MODE 1 register */
+	s->mode1_reg = 0;
+	/* Enable IRQ pin */
+	s->mode1_reg |= MAX3107_MODE1_IRQSEL_BIT;
+	/* Disable TX */
+	s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT;
+	s->tx_enabled = 0;
+	/* RX is enabled */
+	s->rx_enabled = 1;
+	buf[4] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG)
+		| s->mode1_reg;
+
+	/* 4. Configure MODE 2 register */
+	buf[5] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG);
+	if (s->loopback) {
+		/* Enable loopback */
+		buf[5] |= MAX3107_MODE2_LOOPBACK_BIT;
+	}
+	/* Reset FIFOs */
+	buf[5] |= MAX3107_MODE2_FIFORST_BIT;
+	s->tx_fifo_empty = 1;
+
+	/* 5. Configure FIFO trigger level register */
+	buf[6] = (MAX3107_WRITE_BIT | MAX3107_FIFOTRIGLVL_REG);
+	/* RX FIFO trigger for 16 words, TX FIFO trigger not used */
+	buf[6] |= (MAX3107_FIFOTRIGLVL_RX(16) | MAX3107_FIFOTRIGLVL_TX(0));
+
+	/* 6. Configure flow control levels */
+	buf[7] = (MAX3107_WRITE_BIT | MAX3107_FLOWLVL_REG);
+	/* Flow control halt level 96, resume level 48 */
+	buf[7] |= (MAX3107_FLOWLVL_RES(48) | MAX3107_FLOWLVL_HALT(96));
+
+	/* 7. Configure flow control */
+	buf[8] = (MAX3107_WRITE_BIT | MAX3107_FLOWCTRL_REG);
+	/* Enable auto CTS and auto RTS flow control */
+	buf[8] |= (MAX3107_FLOWCTRL_AUTOCTS_BIT | MAX3107_FLOWCTRL_AUTORTS_BIT);
+
+	/* 8. Configure RX timeout register */
+	buf[9] = (MAX3107_WRITE_BIT | MAX3107_RXTO_REG);
+	/* Timeout after 48 character intervals */
+	buf[9] |= 0x0030;
+
+	/* 9. Configure LSR interrupt enable register */
+	buf[10] = (MAX3107_WRITE_BIT | MAX3107_LSR_IRQEN_REG);
+	/* Enable RX timeout interrupt */
+	buf[10] |= MAX3107_LSR_RXTO_BIT;
+
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, NULL, 22))
+		dev_err(&s->spi->dev, "SPI transfer for init failed\n");
+
+	/* 10. Clear IRQ status register by reading it */
+	buf[0] = MAX3107_IRQSTS_REG;
+
+	/* 11. Configure interrupt enable register */
+	/* Enable LSR interrupt */
+	s->irqen_reg = MAX3107_IRQ_LSR_BIT;
+	/* Enable RX FIFO interrupt */
+	s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT;
+	buf[1] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG)
+		| s->irqen_reg;
+
+	/* 12. Clear FIFO reset that was set in step 6 */
+	buf[2] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG);
+	if (s->loopback) {
+		/* Keep loopback enabled */
+		buf[2] |= MAX3107_MODE2_LOOPBACK_BIT;
+	}
+
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 6))
+		dev_err(&s->spi->dev, "SPI transfer for init failed\n");
+
+}
+
+/* IRQ handler */
+static irqreturn_t max3107_irq(int irqno, void *dev_id)
+{
+	struct max3107_port *s = dev_id;
+
+	if (irqno != s->spi->irq) {
+		/* Unexpected IRQ */
+		return IRQ_NONE;
+	}
+
+	/* Indicate irq */
+	s->handle_irq = 1;
+
+	/* Trigger work thread */
+	max3107_dowork(s);
+
+	return IRQ_HANDLED;
+}
+
+/* HW suspension function
+ *
+ * Currently autosleep is used to decrease current consumption, alternative
+ * approach would be to set the chip to reset mode if UART is not being
+ * used but that would mess the GPIOs
+ *
+ */
+static void max3107_hw_susp(struct max3107_port *s, int suspend)
+{
+	pr_debug("enter, suspend %d\n", suspend);
+
+	if (suspend) {
+		/* Suspend requested,
+		 * enable autosleep to decrease current consumption
+		 */
+		s->suspended = 1;
+		max3107_set_sleep(s, MAX3107_ENABLE_AUTOSLEEP);
+	} else {
+		/* Resume requested,
+		 * disable autosleep
+		 */
+		s->suspended = 0;
+		max3107_set_sleep(s, MAX3107_DISABLE_AUTOSLEEP);
+	}
+}
+
+/* Modem status IRQ enabling */
+static void max3107_enable_ms(struct uart_port *port)
+{
+	/* Modem status not supported */
+}
+
+/* Data send function */
+static void max3107_start_tx(struct uart_port *port)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+	/* Trigger work thread for sending data */
+	max3107_dowork(s);
+}
+
+/* Function for checking that there is no pending transfers */
+static unsigned int max3107_tx_empty(struct uart_port *port)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+	pr_debug("returning %d\n",
+		  (s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit)));
+	return s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit);
+}
+
+/* Function for stopping RX */
+static void max3107_stop_rx(struct uart_port *port)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+	unsigned long flags;
+
+	/* Set RX disabled in MODE 1 register */
+	spin_lock_irqsave(&s->data_lock, flags);
+	s->mode1_reg |= MAX3107_MODE1_RXDIS_BIT;
+	s->mode1_commit = 1;
+	spin_unlock_irqrestore(&s->data_lock, flags);
+	/* Set RX disabled */
+	s->rx_enabled = 0;
+	/* Trigger work thread for doing the actual configuration change */
+	max3107_dowork(s);
+}
+
+/* Function for returning control pin states */
+static unsigned int max3107_get_mctrl(struct uart_port *port)
+{
+	/* DCD and DSR are not wired and CTS/RTS is handled automatically
+	 * so just indicate DSR and CAR asserted
+	 */
+	return TIOCM_DSR | TIOCM_CAR;
+}
+
+/* Function for setting control pin states */
+static void max3107_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	/* DCD and DSR are not wired and CTS/RTS is hadnled automatically
+	 * so do nothing
+	 */
+}
+
+/* Function for configuring UART parameters */
+static void max3107_set_termios(struct uart_port *port,
+				struct ktermios *termios,
+				struct ktermios *old)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+	struct tty_struct *tty;
+	int baud;
+	u16 new_lcr = 0;
+	u32 new_brg = 0;
+	unsigned long flags;
+
+	if (!port->state)
+		return;
+
+	tty = port->state->port.tty;
+	if (!tty)
+		return;
+
+	/* Get new LCR register values */
+	/* Word size */
+	if ((termios->c_cflag & CSIZE) == CS7)
+		new_lcr |= MAX3107_LCR_WORD_LEN_7;
+	else
+		new_lcr |= MAX3107_LCR_WORD_LEN_8;
+
+	/* Parity */
+	if (termios->c_cflag & PARENB) {
+		new_lcr |= MAX3107_LCR_PARITY_BIT;
+		if (!(termios->c_cflag & PARODD))
+			new_lcr |= MAX3107_LCR_EVENPARITY_BIT;
+	}
+
+	/* Stop bits */
+	if (termios->c_cflag & CSTOPB) {
+		/* 2 stop bits */
+		new_lcr |= MAX3107_LCR_STOPLEN_BIT;
+	}
+
+	/* Mask termios capabilities we don't support */
+	termios->c_cflag &= ~CMSPAR;
+
+	/* Set status ignore mask */
+	s->port.ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		s->port.ignore_status_mask |= MAX3107_ALL_ERRORS;
+
+	/* Set low latency to immediately handle pushed data */
+	s->port.state->port.tty->low_latency = 1;
+
+	/* Get new baud rate generator configuration */
+	baud = tty_get_baud_rate(tty);
+
+	spin_lock_irqsave(&s->data_lock, flags);
+	new_brg = get_new_brg(baud, s);
+	/* if can't find the corrent config, use previous */
+	if (!new_brg) {
+		baud = s->baud;
+		new_brg = s->brg_cfg;
+	}
+	spin_unlock_irqrestore(&s->data_lock, flags);
+	tty_termios_encode_baud_rate(termios, baud, baud);
+	s->baud = baud;
+
+	/* Update timeout according to new baud rate */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	spin_lock_irqsave(&s->data_lock, flags);
+	if (s->lcr_reg != new_lcr) {
+		s->lcr_reg = new_lcr;
+		s->lcr_commit = 1;
+	}
+	if (s->brg_cfg != new_brg) {
+		s->brg_cfg = new_brg;
+		s->brg_commit = 1;
+	}
+	spin_unlock_irqrestore(&s->data_lock, flags);
+
+	/* Trigger work thread for doing the actual configuration change */
+	max3107_dowork(s);
+}
+
+/* Port shutdown function */
+static void max3107_shutdown(struct uart_port *port)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+	if (s->suspended) {
+		/* Resume HW */
+		max3107_hw_susp(s, 0);
+	}
+
+	/* Free the interrupt */
+	free_irq(s->spi->irq, s);
+
+	if (s->workqueue) {
+		/* Flush and destroy work queue */
+		flush_workqueue(s->workqueue);
+		destroy_workqueue(s->workqueue);
+		s->workqueue = NULL;
+	}
+
+	/* Suspend HW */
+	max3107_hw_susp(s, 1);
+}
+
+/* Port startup function */
+static int max3107_startup(struct uart_port *port)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+	/* Initialize work queue */
+	s->workqueue = create_freezeable_workqueue("max3107");
+	if (!s->workqueue) {
+		dev_err(&s->spi->dev, "Workqueue creation failed\n");
+		return -EBUSY;
+	}
+	INIT_WORK(&s->work, max3107_work);
+
+	/* Setup IRQ */
+	if (request_irq(s->spi->irq, max3107_irq, IRQF_TRIGGER_FALLING,
+			"max3107", s)) {
+		dev_err(&s->spi->dev, "IRQ reguest failed\n");
+		destroy_workqueue(s->workqueue);
+		s->workqueue = NULL;
+		return -EBUSY;
+	}
+
+	/* Resume HW */
+	max3107_hw_susp(s, 0);
+
+	/* Init registers */
+	max3107_register_init(s);
+
+	return 0;
+}
+
+/* Port type function */
+static const char *max3107_type(struct uart_port *port)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+	return s->spi->modalias;
+}
+
+/* Port release function */
+static void max3107_release_port(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+/* Port request function */
+static int max3107_request_port(struct uart_port *port)
+{
+	/* Do nothing */
+	return 0;
+}
+
+/* Port config function */
+static void max3107_config_port(struct uart_port *port, int flags)
+{
+	struct max3107_port *s = container_of(port, struct max3107_port, port);
+
+	/* Use PORT_MAX3100 since we are at least int the same series */
+	s->port.type = PORT_MAX3100;
+}
+
+/* Port verify function */
+static int max3107_verify_port(struct uart_port *port,
+				struct serial_struct *ser)
+{
+	if (ser->type == PORT_UNKNOWN || ser->type == PORT_MAX3100)
+		return 0;
+
+	return -EINVAL;
+}
+
+/* Port stop TX function */
+static void max3107_stop_tx(struct uart_port *port)
+{
+	/* Do nothing */
+}
+
+/* Port break control function */
+static void max3107_break_ctl(struct uart_port *port, int break_state)
+{
+	/* We don't support break control, do nothing */
+}
+
+/* GPIO direction to input function */
+static int max3107_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
+{
+	struct max3107_port *s = container_of(chip, struct max3107_port, chip);
+	u16 buf[1];		/* Buffer for SPI transfer */
+
+	if (offset >= MAX3107_GPIO_COUNT) {
+		dev_err(&s->spi->dev, "Invalid GPIO\n");
+		return -EINVAL;
+	}
+
+	/* Read current GPIO configuration register */
+	buf[0] = MAX3107_GPIOCFG_REG;
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
+		dev_err(&s->spi->dev, "SPI transfer GPIO read failed\n");
+		return -EIO;
+	}
+	buf[0] &= MAX3107_SPI_RX_DATA_MASK;
+
+	/* Set GPIO to input */
+	buf[0] &= ~(0x0001 << offset);
+
+	/* Write new GPIO configuration register value */
+	buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIOCFG_REG);
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, NULL, 2)) {
+		dev_err(&s->spi->dev, "SPI transfer GPIO write failed\n");
+		return -EIO;
+	}
+	return 0;
+}
+
+/* GPIO direction to output function */
+static int max3107_gpio_direction_out(struct gpio_chip *chip, unsigned offset,
+					int value)
+{
+	struct max3107_port *s = container_of(chip, struct max3107_port, chip);
+	u16 buf[2];	/* Buffer for SPI transfers */
+
+	if (offset >= MAX3107_GPIO_COUNT) {
+		dev_err(&s->spi->dev, "Invalid GPIO\n");
+		return -EINVAL;
+	}
+
+	/* Read current GPIO configuration and data registers */
+	buf[0] = MAX3107_GPIOCFG_REG;
+	buf[1] = MAX3107_GPIODATA_REG;
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 4)) {
+		dev_err(&s->spi->dev, "SPI transfer gpio failed\n");
+		return -EIO;
+	}
+	buf[0] &= MAX3107_SPI_RX_DATA_MASK;
+	buf[1] &= MAX3107_SPI_RX_DATA_MASK;
+
+	/* Set GPIO to output */
+	buf[0] |= (0x0001 << offset);
+	/* Set value */
+	if (value)
+		buf[1] |= (0x0001 << offset);
+	else
+		buf[1] &= ~(0x0001 << offset);
+
+	/* Write new GPIO configuration and data register values */
+	buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIOCFG_REG);
+	buf[1] |= (MAX3107_WRITE_BIT | MAX3107_GPIODATA_REG);
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, NULL, 4)) {
+		dev_err(&s->spi->dev,
+			"SPI transfer for GPIO conf data w failed\n");
+		return -EIO;
+	}
+	return 0;
+}
+
+/* GPIO value query function */
+static int max3107_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct max3107_port *s = container_of(chip, struct max3107_port, chip);
+	u16 buf[1];	/* Buffer for SPI transfer */
+
+	if (offset >= MAX3107_GPIO_COUNT) {
+		dev_err(&s->spi->dev, "Invalid GPIO\n");
+		return -EINVAL;
+	}
+
+	/* Read current GPIO data register */
+	buf[0] = MAX3107_GPIODATA_REG;
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
+		dev_err(&s->spi->dev, "SPI transfer GPIO data r failed\n");
+		return -EIO;
+	}
+	buf[0] &= MAX3107_SPI_RX_DATA_MASK;
+
+	/* Return value */
+	return buf[0] & (0x0001 << offset);
+}
+
+/* GPIO value set function */
+static void max3107_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct max3107_port *s = container_of(chip, struct max3107_port, chip);
+	u16 buf[2];	/* Buffer for SPI transfers */
+
+	if (offset >= MAX3107_GPIO_COUNT) {
+		dev_err(&s->spi->dev, "Invalid GPIO\n");
+		return;
+	}
+
+	/* Read current GPIO configuration registers*/
+	buf[0] = MAX3107_GPIODATA_REG;
+	buf[1] = MAX3107_GPIOCFG_REG;
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 4)) {
+		dev_err(&s->spi->dev,
+			"SPI transfer for GPIO data and config read failed\n");
+		return;
+	}
+	buf[0] &= MAX3107_SPI_RX_DATA_MASK;
+	buf[1] &= MAX3107_SPI_RX_DATA_MASK;
+
+	if (!(buf[1] & (0x0001 << offset))) {
+		/* Configured as input, can't set value */
+		dev_warn(&s->spi->dev,
+				"Trying to set value for input GPIO\n");
+		return;
+	}
+
+	/* Set value */
+	if (value)
+		buf[0] |= (0x0001 << offset);
+	else
+		buf[0] &= ~(0x0001 << offset);
+
+	/* Write new GPIO data register value */
+	buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIODATA_REG);
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, NULL, 2))
+		dev_err(&s->spi->dev, "SPI transfer GPIO data w failed\n");
+}
+
+/* Platform data */
+static struct max3107_plat max3107_plat_data = {
+	.loopback               = 0,
+	.ext_clk                = 1,
+	.max3107_hw_suspend     = &max3107_hw_susp,
+	.polled_mode            = 0,
+	.poll_time              = 0,
+};
+
+/* Port functions */
+static struct uart_ops max3107_ops = {
+	.tx_empty       = max3107_tx_empty,
+	.set_mctrl      = max3107_set_mctrl,
+	.get_mctrl      = max3107_get_mctrl,
+	.stop_tx        = max3107_stop_tx,
+	.start_tx       = max3107_start_tx,
+	.stop_rx        = max3107_stop_rx,
+	.enable_ms      = max3107_enable_ms,
+	.break_ctl      = max3107_break_ctl,
+	.startup        = max3107_startup,
+	.shutdown       = max3107_shutdown,
+	.set_termios    = max3107_set_termios,
+	.type           = max3107_type,
+	.release_port   = max3107_release_port,
+	.request_port   = max3107_request_port,
+	.config_port    = max3107_config_port,
+	.verify_port    = max3107_verify_port,
+};
+
+/* UART driver data */
+static struct uart_driver max3107_uart_driver = {
+	.owner          = THIS_MODULE,
+	.driver_name    = "ttyMAX",
+	.dev_name       = "ttyMAX",
+	.nr             = 1,
+};
+
+/* GPIO chip data */
+static struct gpio_chip max3107_gpio_chip = {
+	.owner			= THIS_MODULE,
+	.direction_input	= max3107_gpio_direction_in,
+	.direction_output	= max3107_gpio_direction_out,
+	.get			= max3107_gpio_get,
+	.set			= max3107_gpio_set,
+	.can_sleep		= 1,
+	.base			= MAX3107_GPIO_BASE,
+	.ngpio			= MAX3107_GPIO_COUNT,
+};
+/* Device probe function */
+static int __devinit max3107_probe(struct spi_device *spi)
+{
+	struct max3107_port *s;
+	struct max3107_plat *pdata = &max3107_plat_data;
+	u16 buf[2];	/* Buffer for SPI transfers */
+	int retval;
+
+	pr_info("enter max3107 probe\n");
+
+	/* Reset the chip */
+	if (gpio_request(MAX3107_RESET_GPIO, "max3107")) {
+		pr_err("Requesting RESET GPIO failed\n");
+		return -EIO;
+	}
+	if (gpio_direction_output(MAX3107_RESET_GPIO, 0)) {
+		pr_err("Setting RESET GPIO to 0 failed\n");
+		gpio_free(MAX3107_RESET_GPIO);
+		return -EIO;
+	}
+	msleep(MAX3107_RESET_DELAY);
+	if (gpio_direction_output(MAX3107_RESET_GPIO, 1)) {
+		pr_err("Setting RESET GPIO to 1 failed\n");
+		gpio_free(MAX3107_RESET_GPIO);
+		return -EIO;
+	}
+	gpio_free(MAX3107_RESET_GPIO);
+	msleep(MAX3107_WAKEUP_DELAY);
+
+	/* Allocate port structure */
+	s = kzalloc(sizeof(*s), GFP_KERNEL);
+	if (!s) {
+		pr_err("Allocating port structure failed\n");
+		return -ENOMEM;
+	}
+	/* SPI Rx buffer
+	 * +2 for RX FIFO interrupt
+	 * disabling and RX level query
+	 */
+	s->rxbuf = kzalloc(sizeof(u16) * (MAX3107_RX_FIFO_SIZE+2), GFP_KERNEL);
+	if (!s->rxbuf) {
+		pr_err("Allocating RX buffer failed\n");
+		return -ENOMEM;
+	}
+	s->rxstr = kzalloc(sizeof(u8) * MAX3107_RX_FIFO_SIZE, GFP_KERNEL);
+	if (!s->rxstr) {
+		pr_err("Allocating RX buffer failed\n");
+		return -ENOMEM;
+	}
+	/* SPI Tx buffer
+	 * SPI transfer buffer
+	 * +3 for TX FIFO empty
+	 * interrupt disabling and
+	 * enabling and TX enabling
+	 */
+	s->txbuf = kzalloc(sizeof(u16) * MAX3107_TX_FIFO_SIZE + 3, GFP_KERNEL);
+	if (!s->txbuf) {
+		pr_err("Allocating TX buffer failed\n");
+		return -ENOMEM;
+	}
+	/* Initialize shared data lock */
+	spin_lock_init(&s->data_lock);
+
+	/* SPI intializations */
+	dev_set_drvdata(&spi->dev, s);
+	spi->mode = SPI_MODE_0;
+	spi->dev.platform_data = pdata;
+	spi->bits_per_word = 16;
+	s->ext_clk = pdata->ext_clk;
+	s->loopback = pdata->loopback;
+	spi_setup(spi);
+	s->spi = spi;
+
+	/* Check REV ID to ensure we are talking to what we expect */
+	buf[0] = MAX3107_REVID_REG;
+	if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) {
+		dev_err(&s->spi->dev, "SPI transfer for REVID read failed\n");
+		return -EIO;
+	}
+	if ((buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID1 &&
+		(buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID2) {
+		dev_err(&s->spi->dev, "REVID %x does not match\n",
+				(buf[0] & MAX3107_SPI_RX_DATA_MASK));
+		return -ENODEV;
+	}
+
+	/* Disable all interrupts */
+	buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG | 0x0000);
+	buf[0] |= 0x0000;
+
+	/* Configure clock source */
+	buf[1] = (MAX3107_WRITE_BIT | MAX3107_CLKSRC_REG);
+	if (s->ext_clk) {
+		/* External clock */
+		buf[1] |= MAX3107_CLKSRC_EXTCLK_BIT;
+	}
+
+	/* PLL bypass ON */
+	buf[1] |= MAX3107_CLKSRC_PLLBYP_BIT;
+
+	/* Perform SPI transfer */
+	if (max3107_rw(s, (u8 *)buf, NULL, 4)) {
+		dev_err(&s->spi->dev, "SPI transfer for init failed\n");
+		return -EIO;
+	}
+
+	/* Register UART driver */
+	retval = uart_register_driver(&max3107_uart_driver);
+	if (retval) {
+		dev_err(&s->spi->dev, "Registering UART driver failed\n");
+		return retval;
+	}
+
+	/* Initialize UART port data */
+	s->port.fifosize = 128;
+	s->port.ops = &max3107_ops;
+	s->port.line = 0;
+	s->port.dev = &spi->dev;
+	s->port.uartclk = 9600;
+	s->port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
+	s->port.irq = s->spi->irq;
+	/* Use PORT_MAX3100 since we are at least in the same series */
+	s->port.type = PORT_MAX3100;
+
+	/* Add UART port */
+	retval = uart_add_one_port(&max3107_uart_driver, &s->port);
+	if (retval < 0) {
+		dev_err(&s->spi->dev, "Adding UART port failed\n");
+		return retval;
+	}
+
+	/* Initialize GPIO chip data */
+	s->chip = max3107_gpio_chip;
+	s->chip.label = spi->modalias;
+	s->chip.dev = &spi->dev;
+
+	/* Add GPIO chip */
+	retval = gpiochip_add(&s->chip);
+	if (retval) {
+		dev_err(&s->spi->dev, "Adding GPIO chip failed\n");
+		return retval;
+	}
+
+	/* Temporary fix for EV2 boot problems, set modem reset to 0 */
+	max3107_gpio_direction_out(&s->chip, 3, 0);
+
+	/* Go to suspend mode */
+	max3107_hw_susp(s, 1);
+
+	return 0;
+}
+
+/* Driver remove function */
+static int __devexit max3107_remove(struct spi_device *spi)
+{
+	struct max3107_port *s = dev_get_drvdata(&spi->dev);
+
+	pr_info("enter max3107 remove\n");
+
+	/* Remove GPIO chip */
+	if (gpiochip_remove(&s->chip))
+		dev_warn(&s->spi->dev, "Removing GPIO chip failed\n");
+
+	/* Remove port */
+	if (uart_remove_one_port(&max3107_uart_driver, &s->port))
+		dev_warn(&s->spi->dev, "Removing UART port failed\n");
+
+	/* Unregister UART driver */
+	uart_unregister_driver(&max3107_uart_driver);
+
+	/* Free TxRx buffer */
+	kfree(s->rxbuf);
+	kfree(s->rxstr);
+	kfree(s->txbuf);
+
+	/* Free port structure */
+	kfree(s);
+
+	return 0;
+}
+
+/* Driver suspend function */
+static int max3107_suspend(struct spi_device *spi, pm_message_t state)
+{
+#ifdef CONFIG_PM
+	struct max3107_port *s = dev_get_drvdata(&spi->dev);
+
+	pr_debug("enter suspend\n");
+
+	/* Suspend UART port */
+	uart_suspend_port(&max3107_uart_driver, &s->port);
+
+	/* Go to suspend mode */
+	max3107_hw_susp(s, 1);
+#endif	/* CONFIG_PM */
+	return 0;
+}
+
+/* Driver resume function */
+static int max3107_resume(struct spi_device *spi)
+{
+#ifdef CONFIG_PM
+	struct max3107_port *s = dev_get_drvdata(&spi->dev);
+
+	pr_debug("enter resume\n");
+
+	/* Resume from suspend */
+	max3107_hw_susp(s, 0);
+
+	/* Resume UART port */
+	uart_resume_port(&max3107_uart_driver, &s->port);
+#endif	/* CONFIG_PM */
+	return 0;
+}
+
+/* Spi driver data */
+static struct spi_driver max3107_driver = {
+	.driver = {
+		.name		= "max3107",
+		.bus		= &spi_bus_type,
+		.owner		= THIS_MODULE,
+	},
+	.probe		= max3107_probe,
+	.remove		= __devexit_p(max3107_remove),
+	.suspend	= max3107_suspend,
+	.resume		= max3107_resume,
+};
+
+/* Driver init function */
+static int __init max3107_init(void)
+{
+	pr_info("enter max3107 init\n");
+	return spi_register_driver(&max3107_driver);
+}
+
+/* Driver exit function */
+static void __exit max3107_exit(void)
+{
+	pr_info("enter max3107 exit\n");
+	spi_unregister_driver(&max3107_driver);
+}
+
+module_init(max3107_init);
+module_exit(max3107_exit);
+
+MODULE_DESCRIPTION("MAX3107 driver");
+MODULE_AUTHOR("Aavamobile");
+MODULE_ALIAS("max3107-spi-uart");
+MODULE_LICENSE("GPLv2");

drivers/serial/max3107.h

@@ -0,0 +1,358 @@
+/*
+ * max3107.h - spi uart protocol driver header for Maxim 3107
+ *
+ * Copyright (C) Aavamobile 2009
+ * Based on serial_max3100.h by Christian Pellegrin
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _LINUX_SERIAL_MAX3107_H
+#define _LINUX_SERIAL_MAX3107_H
+
+/* Serial error status definitions */
+#define MAX3107_PARITY_ERROR	1
+#define MAX3107_FRAME_ERROR	2
+#define MAX3107_OVERRUN_ERROR	4
+#define MAX3107_ALL_ERRORS	(MAX3107_PARITY_ERROR | \
+				 MAX3107_FRAME_ERROR | \
+				 MAX3107_OVERRUN_ERROR)
+
+/* GPIO definitions */
+#define MAX3107_GPIO_BASE	88
+#define MAX3107_GPIO_COUNT	4
+
+
+/* GPIO connected to chip's reset pin */
+#define MAX3107_RESET_GPIO	87
+
+
+/* Chip reset delay */
+#define MAX3107_RESET_DELAY	10
+
+/* Chip wakeup delay */
+#define MAX3107_WAKEUP_DELAY	50
+
+
+/* Sleep mode definitions */
+#define MAX3107_DISABLE_FORCED_SLEEP	0
+#define MAX3107_ENABLE_FORCED_SLEEP	1
+#define MAX3107_DISABLE_AUTOSLEEP	2
+#define MAX3107_ENABLE_AUTOSLEEP	3
+
+
+/* Definitions for register access with SPI transfers
+ *
+ * SPI transfer format:
+ *
+ * Master to slave bits xzzzzzzzyyyyyyyy
+ * Slave to master bits aaaaaaaabbbbbbbb
+ *
+ * where:
+ * x = 0 for reads, 1 for writes
+ * z = register address
+ * y = new register value if write, 0 if read
+ * a = unspecified
+ * b = register value if read, unspecified if write
+ */
+
+/* SPI speed */
+#define MAX3107_SPI_SPEED	(3125000 * 2)
+
+/* Write bit */
+#define MAX3107_WRITE_BIT	(1 << 15)
+
+/* SPI TX data mask */
+#define MAX3107_SPI_RX_DATA_MASK	(0x00ff)
+
+/* SPI RX data mask */
+#define MAX3107_SPI_TX_DATA_MASK	(0x00ff)
+
+/* Register access masks */
+#define MAX3107_RHR_REG			(0x0000) /* RX FIFO */
+#define MAX3107_THR_REG			(0x0000) /* TX FIFO */
+#define MAX3107_IRQEN_REG		(0x0100) /* IRQ enable */
+#define MAX3107_IRQSTS_REG		(0x0200) /* IRQ status */
+#define MAX3107_LSR_IRQEN_REG		(0x0300) /* LSR IRQ enable */
+#define MAX3107_LSR_IRQSTS_REG		(0x0400) /* LSR IRQ status */
+#define MAX3107_SPCHR_IRQEN_REG		(0x0500) /* Special char IRQ enable */
+#define MAX3107_SPCHR_IRQSTS_REG	(0x0600) /* Special char IRQ status */
+#define MAX3107_STS_IRQEN_REG		(0x0700) /* Status IRQ enable */
+#define MAX3107_STS_IRQSTS_REG		(0x0800) /* Status IRQ status */
+#define MAX3107_MODE1_REG		(0x0900) /* MODE1 */
+#define MAX3107_MODE2_REG		(0x0a00) /* MODE2 */
+#define MAX3107_LCR_REG			(0x0b00) /* LCR */
+#define MAX3107_RXTO_REG		(0x0c00) /* RX timeout */
+#define MAX3107_HDPIXDELAY_REG		(0x0d00) /* Auto transceiver delays */
+#define MAX3107_IRDA_REG		(0x0e00) /* IRDA settings */
+#define MAX3107_FLOWLVL_REG		(0x0f00) /* Flow control levels */
+#define MAX3107_FIFOTRIGLVL_REG		(0x1000) /* FIFO IRQ trigger levels */
+#define MAX3107_TXFIFOLVL_REG		(0x1100) /* TX FIFO level */
+#define MAX3107_RXFIFOLVL_REG		(0x1200) /* RX FIFO level */
+#define MAX3107_FLOWCTRL_REG		(0x1300) /* Flow control */
+#define MAX3107_XON1_REG		(0x1400) /* XON1 character */
+#define MAX3107_XON2_REG		(0x1500) /* XON2 character */
+#define MAX3107_XOFF1_REG		(0x1600) /* XOFF1 character */
+#define MAX3107_XOFF2_REG		(0x1700) /* XOFF2 character */
+#define MAX3107_GPIOCFG_REG		(0x1800) /* GPIO config */
+#define MAX3107_GPIODATA_REG		(0x1900) /* GPIO data */
+#define MAX3107_PLLCFG_REG		(0x1a00) /* PLL config */
+#define MAX3107_BRGCFG_REG		(0x1b00) /* Baud rate generator conf */
+#define MAX3107_BRGDIVLSB_REG		(0x1c00) /* Baud rate divisor LSB */
+#define MAX3107_BRGDIVMSB_REG		(0x1d00) /* Baud rate divisor MSB */
+#define MAX3107_CLKSRC_REG		(0x1e00) /* Clock source */
+#define MAX3107_REVID_REG		(0x1f00) /* Revision identification */
+
+/* IRQ register bits */
+#define MAX3107_IRQ_LSR_BIT	(1 << 0) /* LSR interrupt */
+#define MAX3107_IRQ_SPCHR_BIT	(1 << 1) /* Special char interrupt */
+#define MAX3107_IRQ_STS_BIT	(1 << 2) /* Status interrupt */
+#define MAX3107_IRQ_RXFIFO_BIT	(1 << 3) /* RX FIFO interrupt */
+#define MAX3107_IRQ_TXFIFO_BIT	(1 << 4) /* TX FIFO interrupt */
+#define MAX3107_IRQ_TXEMPTY_BIT	(1 << 5) /* TX FIFO empty interrupt */
+#define MAX3107_IRQ_RXEMPTY_BIT	(1 << 6) /* RX FIFO empty interrupt */
+#define MAX3107_IRQ_CTS_BIT	(1 << 7) /* CTS interrupt */
+
+/* LSR register bits */
+#define MAX3107_LSR_RXTO_BIT	(1 << 0) /* RX timeout */
+#define MAX3107_LSR_RXOVR_BIT	(1 << 1) /* RX overrun */
+#define MAX3107_LSR_RXPAR_BIT	(1 << 2) /* RX parity error */
+#define MAX3107_LSR_FRERR_BIT	(1 << 3) /* Frame error */
+#define MAX3107_LSR_RXBRK_BIT	(1 << 4) /* RX break */
+#define MAX3107_LSR_RXNOISE_BIT	(1 << 5) /* RX noise */
+#define MAX3107_LSR_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
+#define MAX3107_LSR_CTS_BIT	(1 << 7) /* CTS pin state */
+
+/* Special character register bits */
+#define MAX3107_SPCHR_XON1_BIT		(1 << 0) /* XON1 character */
+#define MAX3107_SPCHR_XON2_BIT		(1 << 1) /* XON2 character */
+#define MAX3107_SPCHR_XOFF1_BIT		(1 << 2) /* XOFF1 character */
+#define MAX3107_SPCHR_XOFF2_BIT		(1 << 3) /* XOFF2 character */
+#define MAX3107_SPCHR_BREAK_BIT		(1 << 4) /* RX break */
+#define MAX3107_SPCHR_MULTIDROP_BIT	(1 << 5) /* 9-bit multidrop addr char */
+#define MAX3107_SPCHR_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
+#define MAX3107_SPCHR_UNDEF7_BIT	(1 << 7) /* Undefined/not used */
+
+/* Status register bits */
+#define MAX3107_STS_GPIO0_BIT		(1 << 0) /* GPIO 0 interrupt */
+#define MAX3107_STS_GPIO1_BIT		(1 << 1) /* GPIO 1 interrupt */
+#define MAX3107_STS_GPIO2_BIT		(1 << 2) /* GPIO 2 interrupt */
+#define MAX3107_STS_GPIO3_BIT		(1 << 3) /* GPIO 3 interrupt */
+#define MAX3107_STS_UNDEF4_BIT		(1 << 4) /* Undefined/not used */
+#define MAX3107_STS_CLKREADY_BIT	(1 << 5) /* Clock ready */
+#define MAX3107_STS_SLEEP_BIT		(1 << 6) /* Sleep interrupt */
+#define MAX3107_STS_UNDEF7_BIT		(1 << 7) /* Undefined/not used */
+
+/* MODE1 register bits */
+#define MAX3107_MODE1_RXDIS_BIT		(1 << 0) /* RX disable */
+#define MAX3107_MODE1_TXDIS_BIT		(1 << 1) /* TX disable */
+#define MAX3107_MODE1_TXHIZ_BIT		(1 << 2) /* TX pin three-state */
+#define MAX3107_MODE1_RTSHIZ_BIT	(1 << 3) /* RTS pin three-state */
+#define MAX3107_MODE1_TRNSCVCTRL_BIT	(1 << 4) /* Transceiver ctrl enable */
+#define MAX3107_MODE1_FORCESLEEP_BIT	(1 << 5) /* Force sleep mode */
+#define MAX3107_MODE1_AUTOSLEEP_BIT	(1 << 6) /* Auto sleep enable */
+#define MAX3107_MODE1_IRQSEL_BIT	(1 << 7) /* IRQ pin enable */
+
+/* MODE2 register bits */
+#define MAX3107_MODE2_RST_BIT		(1 << 0) /* Chip reset */
+#define MAX3107_MODE2_FIFORST_BIT	(1 << 1) /* FIFO reset */
+#define MAX3107_MODE2_RXTRIGINV_BIT	(1 << 2) /* RX FIFO INT invert */
+#define MAX3107_MODE2_RXEMPTINV_BIT	(1 << 3) /* RX FIFO empty INT invert */
+#define MAX3107_MODE2_SPCHR_BIT		(1 << 4) /* Special chr detect enable */
+#define MAX3107_MODE2_LOOPBACK_BIT	(1 << 5) /* Internal loopback enable */
+#define MAX3107_MODE2_MULTIDROP_BIT	(1 << 6) /* 9-bit multidrop enable */
+#define MAX3107_MODE2_ECHOSUPR_BIT	(1 << 7) /* ECHO suppression enable */
+
+/* LCR register bits */
+#define MAX3107_LCR_LENGTH0_BIT		(1 << 0) /* Word length bit 0 */
+#define MAX3107_LCR_LENGTH1_BIT		(1 << 1) /* Word length bit 1
+						  *
+						  * Word length bits table:
+						  * 00 -> 5 bit words
+						  * 01 -> 6 bit words
+						  * 10 -> 7 bit words
+						  * 11 -> 8 bit words
+						  */
+#define MAX3107_LCR_STOPLEN_BIT		(1 << 2) /* STOP length bit
+						  *
+						  * STOP length bit table:
+						  * 0 -> 1 stop bit
+						  * 1 -> 1-1.5 stop bits if
+						  *      word length is 5,
+						  *      2 stop bits otherwise
+						  */
+#define MAX3107_LCR_PARITY_BIT		(1 << 3) /* Parity bit enable */
+#define MAX3107_LCR_EVENPARITY_BIT	(1 << 4) /* Even parity bit enable */
+#define MAX3107_LCR_FORCEPARITY_BIT	(1 << 5) /* 9-bit multidrop parity */
+#define MAX3107_LCR_TXBREAK_BIT		(1 << 6) /* TX break enable */
+#define MAX3107_LCR_RTS_BIT		(1 << 7) /* RTS pin control */
+#define MAX3107_LCR_WORD_LEN_5		(0x0000)
+#define MAX3107_LCR_WORD_LEN_6		(0x0001)
+#define MAX3107_LCR_WORD_LEN_7		(0x0002)
+#define MAX3107_LCR_WORD_LEN_8		(0x0003)
+
+
+/* IRDA register bits */
+#define MAX3107_IRDA_IRDAEN_BIT		(1 << 0) /* IRDA mode enable */
+#define MAX3107_IRDA_SIR_BIT		(1 << 1) /* SIR mode enable */
+#define MAX3107_IRDA_SHORTIR_BIT	(1 << 2) /* Short SIR mode enable */
+#define MAX3107_IRDA_MIR_BIT		(1 << 3) /* MIR mode enable */
+#define MAX3107_IRDA_RXINV_BIT		(1 << 4) /* RX logic inversion enable */
+#define MAX3107_IRDA_TXINV_BIT		(1 << 5) /* TX logic inversion enable */
+#define MAX3107_IRDA_UNDEF6_BIT		(1 << 6) /* Undefined/not used */
+#define MAX3107_IRDA_UNDEF7_BIT		(1 << 7) /* Undefined/not used */
+
+/* Flow control trigger level register masks */
+#define MAX3107_FLOWLVL_HALT_MASK	(0x000f) /* Flow control halt level */
+#define MAX3107_FLOWLVL_RES_MASK	(0x00f0) /* Flow control resume level */
+#define MAX3107_FLOWLVL_HALT(words)	((words/8) & 0x000f)
+#define MAX3107_FLOWLVL_RES(words)	(((words/8) & 0x000f) << 4)
+
+/* FIFO interrupt trigger level register masks */
+#define MAX3107_FIFOTRIGLVL_TX_MASK	(0x000f) /* TX FIFO trigger level */
+#define MAX3107_FIFOTRIGLVL_RX_MASK	(0x00f0) /* RX FIFO trigger level */
+#define MAX3107_FIFOTRIGLVL_TX(words)	((words/8) & 0x000f)
+#define MAX3107_FIFOTRIGLVL_RX(words)	(((words/8) & 0x000f) << 4)
+
+/* Flow control register bits */
+#define MAX3107_FLOWCTRL_AUTORTS_BIT	(1 << 0) /* Auto RTS flow ctrl enable */
+#define MAX3107_FLOWCTRL_AUTOCTS_BIT	(1 << 1) /* Auto CTS flow ctrl enable */
+#define MAX3107_FLOWCTRL_GPIADDR_BIT	(1 << 2) /* Enables that GPIO inputs
+						  * are used in conjunction with
+						  * XOFF2 for definition of
+						  * special character */
+#define MAX3107_FLOWCTRL_SWFLOWEN_BIT	(1 << 3) /* Auto SW flow ctrl enable */
+#define MAX3107_FLOWCTRL_SWFLOW0_BIT	(1 << 4) /* SWFLOW bit 0 */
+#define MAX3107_FLOWCTRL_SWFLOW1_BIT	(1 << 5) /* SWFLOW bit 1
+						  *
+						  * SWFLOW bits 1 & 0 table:
+						  * 00 -> no transmitter flow
+						  *       control
+						  * 01 -> receiver compares
+						  *       XON2 and XOFF2
+						  *       and controls
+						  *       transmitter
+						  * 10 -> receiver compares
+						  *       XON1 and XOFF1
+						  *       and controls
+						  *       transmitter
+						  * 11 -> receiver compares
+						  *       XON1, XON2, XOFF1 and
+						  *       XOFF2 and controls
+						  *       transmitter
+						  */
+#define MAX3107_FLOWCTRL_SWFLOW2_BIT	(1 << 6) /* SWFLOW bit 2 */
+#define MAX3107_FLOWCTRL_SWFLOW3_BIT	(1 << 7) /* SWFLOW bit 3
+						  *
+						  * SWFLOW bits 3 & 2 table:
+						  * 00 -> no received flow
+						  *       control
+						  * 01 -> transmitter generates
+						  *       XON2 and XOFF2
+						  * 10 -> transmitter generates
+						  *       XON1 and XOFF1
+						  * 11 -> transmitter generates
+						  *       XON1, XON2, XOFF1 and
+						  *       XOFF2
+						  */
+
+/* GPIO configuration register bits */
+#define MAX3107_GPIOCFG_GP0OUT_BIT	(1 << 0) /* GPIO 0 output enable */
+#define MAX3107_GPIOCFG_GP1OUT_BIT	(1 << 1) /* GPIO 1 output enable */
+#define MAX3107_GPIOCFG_GP2OUT_BIT	(1 << 2) /* GPIO 2 output enable */
+#define MAX3107_GPIOCFG_GP3OUT_BIT	(1 << 3) /* GPIO 3 output enable */
+#define MAX3107_GPIOCFG_GP0OD_BIT	(1 << 4) /* GPIO 0 open-drain enable */
+#define MAX3107_GPIOCFG_GP1OD_BIT	(1 << 5) /* GPIO 1 open-drain enable */
+#define MAX3107_GPIOCFG_GP2OD_BIT	(1 << 6) /* GPIO 2 open-drain enable */
+#define MAX3107_GPIOCFG_GP3OD_BIT	(1 << 7) /* GPIO 3 open-drain enable */
+
+/* GPIO DATA register bits */
+#define MAX3107_GPIODATA_GP0OUT_BIT	(1 << 0) /* GPIO 0 output value */
+#define MAX3107_GPIODATA_GP1OUT_BIT	(1 << 1) /* GPIO 1 output value */
+#define MAX3107_GPIODATA_GP2OUT_BIT	(1 << 2) /* GPIO 2 output value */
+#define MAX3107_GPIODATA_GP3OUT_BIT	(1 << 3) /* GPIO 3 output value */
+#define MAX3107_GPIODATA_GP0IN_BIT	(1 << 4) /* GPIO 0 input value */
+#define MAX3107_GPIODATA_GP1IN_BIT	(1 << 5) /* GPIO 1 input value */
+#define MAX3107_GPIODATA_GP2IN_BIT	(1 << 6) /* GPIO 2 input value */
+#define MAX3107_GPIODATA_GP3IN_BIT	(1 << 7) /* GPIO 3 input value */
+
+/* PLL configuration register masks */
+#define MAX3107_PLLCFG_PREDIV_MASK	(0x003f) /* PLL predivision value */
+#define MAX3107_PLLCFG_PLLFACTOR_MASK	(0x00c0) /* PLL multiplication factor */
+
+/* Baud rate generator configuration register masks and bits */
+#define MAX3107_BRGCFG_FRACT_MASK	(0x000f) /* Fractional portion of
+						  * Baud rate generator divisor
+						  */
+#define MAX3107_BRGCFG_2XMODE_BIT	(1 << 4) /* Double baud rate */
+#define MAX3107_BRGCFG_4XMODE_BIT	(1 << 5) /* Quadruple baud rate */
+#define MAX3107_BRGCFG_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
+#define MAX3107_BRGCFG_UNDEF7_BIT	(1 << 7) /* Undefined/not used */
+
+/* Clock source register bits */
+#define MAX3107_CLKSRC_INTOSC_BIT	(1 << 0) /* Internal osc enable */
+#define MAX3107_CLKSRC_CRYST_BIT	(1 << 1) /* Crystal osc enable */
+#define MAX3107_CLKSRC_PLL_BIT		(1 << 2) /* PLL enable */
+#define MAX3107_CLKSRC_PLLBYP_BIT	(1 << 3) /* PLL bypass */
+#define MAX3107_CLKSRC_EXTCLK_BIT	(1 << 4) /* External clock enable */
+#define MAX3107_CLKSRC_UNDEF5_BIT	(1 << 5) /* Undefined/not used */
+#define MAX3107_CLKSRC_UNDEF6_BIT	(1 << 6) /* Undefined/not used */
+#define MAX3107_CLKSRC_CLK2RTS_BIT	(1 << 7) /* Baud clk to RTS pin */
+
+
+/* HW definitions */
+#define MAX3107_RX_FIFO_SIZE	128
+#define MAX3107_TX_FIFO_SIZE	128
+#define MAX3107_REVID1		0x00a0
+#define MAX3107_REVID2		0x00a1
+
+
+/* Baud rate generator configuration values for external clock 13MHz */
+#define MAX3107_BRG13_B300	(0x0A9400 | 0x05)
+#define MAX3107_BRG13_B600	(0x054A00 | 0x03)
+#define MAX3107_BRG13_B1200	(0x02A500 | 0x01)
+#define MAX3107_BRG13_B2400	(0x015200 | 0x09)
+#define MAX3107_BRG13_B4800	(0x00A900 | 0x04)
+#define MAX3107_BRG13_B9600	(0x005400 | 0x0A)
+#define MAX3107_BRG13_B19200	(0x002A00 | 0x05)
+#define MAX3107_BRG13_B38400	(0x001500 | 0x03)
+#define MAX3107_BRG13_B57600	(0x000E00 | 0x02)
+#define MAX3107_BRG13_B115200	(0x000700 | 0x01)
+#define MAX3107_BRG13_B230400	(0x000300 | 0x08)
+#define MAX3107_BRG13_B460800	(0x000100 | 0x0c)
+#define MAX3107_BRG13_B921600	(0x000100 | 0x1c)
+
+/* Baud rate generator configuration values for external clock 26MHz */
+#define MAX3107_BRG26_B300	(0x152800 | 0x0A)
+#define MAX3107_BRG26_B600	(0x0A9400 | 0x05)
+#define MAX3107_BRG26_B1200	(0x054A00 | 0x03)
+#define MAX3107_BRG26_B2400	(0x02A500 | 0x01)
+#define MAX3107_BRG26_B4800	(0x015200 | 0x09)
+#define MAX3107_BRG26_B9600	(0x00A900 | 0x04)
+#define MAX3107_BRG26_B19200	(0x005400 | 0x0A)
+#define MAX3107_BRG26_B38400	(0x002A00 | 0x05)
+#define MAX3107_BRG26_B57600	(0x001C00 | 0x03)
+#define MAX3107_BRG26_B115200	(0x000E00 | 0x02)
+#define MAX3107_BRG26_B230400	(0x000700 | 0x01)
+#define MAX3107_BRG26_B460800	(0x000300 | 0x08)
+#define MAX3107_BRG26_B921600	(0x000100 | 0x0C)
+
+/* Baud rate generator configuration values for internal clock */
+#define MAX3107_BRG13_IB300	(0x008000 | 0x00)
+#define MAX3107_BRG13_IB600	(0x004000 | 0x00)
+#define MAX3107_BRG13_IB1200	(0x002000 | 0x00)
+#define MAX3107_BRG13_IB2400	(0x001000 | 0x00)
+#define MAX3107_BRG13_IB4800	(0x000800 | 0x00)
+#define MAX3107_BRG13_IB9600	(0x000400 | 0x00)
+#define MAX3107_BRG13_IB19200	(0x000200 | 0x00)
+#define MAX3107_BRG13_IB38400	(0x000100 | 0x00)
+#define MAX3107_BRG13_IB57600	(0x000000 | 0x0B)
+#define MAX3107_BRG13_IB115200	(0x000000 | 0x05)
+#define MAX3107_BRG13_IB230400	(0x000000 | 0x03)
+#define MAX3107_BRG13_IB460800	(0x000000 | 0x00)
+#define MAX3107_BRG13_IB921600	(0x000000 | 0x00)
+
+#endif /* _LINUX_SERIAL_MAX3107_H */