bnx2x: Add Warpcore support for 578xx

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>

drivers/net/bnx2x/bnx2x_link.h

@@ -33,12 +33,13 @@
 #define BNX2X_FLOW_CTRL_BOTH		PORT_FEATURE_FLOW_CONTROL_BOTH
 #define BNX2X_FLOW_CTRL_NONE		PORT_FEATURE_FLOW_CONTROL_NONE
 
+#define NET_SERDES_IF_XFI		1
+#define NET_SERDES_IF_SFI		2
+#define NET_SERDES_IF_KR		3
+#define NET_SERDES_IF_DXGXS	4
+
 #define SPEED_AUTO_NEG		0
-#define SPEED_12000		12000
-#define SPEED_12500		12500
-#define SPEED_13000		13000
-#define SPEED_15000		15000
-#define SPEED_16000		16000
+#define SPEED_20000		20000
 
 #define SFP_EEPROM_VENDOR_NAME_ADDR		0x14
 #define SFP_EEPROM_VENDOR_NAME_SIZE		16
@@ -46,6 +47,12 @@
 #define SFP_EEPROM_VENDOR_OUI_SIZE		3
 #define SFP_EEPROM_PART_NO_ADDR			0x28
 #define SFP_EEPROM_PART_NO_SIZE			16
+#define SFP_EEPROM_REVISION_ADDR		0x38
+#define SFP_EEPROM_REVISION_SIZE		4
+#define SFP_EEPROM_SERIAL_ADDR			0x44
+#define SFP_EEPROM_SERIAL_SIZE			16
+#define SFP_EEPROM_DATE_ADDR			0x54 /* ASCII YYMMDD */
+#define SFP_EEPROM_DATE_SIZE			6
 #define PWR_FLT_ERR_MSG_LEN			250
 
 #define XGXS_EXT_PHY_TYPE(ext_phy_config) \
@@ -62,7 +69,18 @@
 #define SINGLE_MEDIA(params)		(params->num_phys == 2)
 /* Dual Media board contains two external phy with different media */
 #define DUAL_MEDIA(params)		(params->num_phys == 3)
+
+#define FW_PARAM_PHY_ADDR_MASK		0x000000FF
+#define FW_PARAM_PHY_TYPE_MASK		0x0000FF00
+#define FW_PARAM_MDIO_CTRL_MASK		0xFFFF0000
 #define FW_PARAM_MDIO_CTRL_OFFSET		16
+#define FW_PARAM_PHY_ADDR(fw_param) (fw_param & \
+					   FW_PARAM_PHY_ADDR_MASK)
+#define FW_PARAM_PHY_TYPE(fw_param) (fw_param & \
+					   FW_PARAM_PHY_TYPE_MASK)
+#define FW_PARAM_MDIO_CTRL(fw_param) ((fw_param & \
+					    FW_PARAM_MDIO_CTRL_MASK) >> \
+					    FW_PARAM_MDIO_CTRL_OFFSET)
 #define FW_PARAM_SET(phy_addr, phy_type, mdio_access) \
 	(phy_addr | phy_type | mdio_access << FW_PARAM_MDIO_CTRL_OFFSET)
 
@@ -121,9 +139,12 @@ struct bnx2x_phy {
 #define FLAGS_FAN_FAILURE_DET_REQ	(1<<2)
 	/* Initialize first the XGXS and only then the phy itself */
 #define FLAGS_INIT_XGXS_FIRST		(1<<3)
+#define FLAGS_WC_DUAL_MODE		(1<<4)
 #define FLAGS_4_PORT_MODE		(1<<5)
 #define FLAGS_REARM_LATCH_SIGNAL	(1<<6)
 #define FLAGS_SFP_NOT_APPROVED		(1<<7)
+#define FLAGS_MDC_MDIO_WA		(1<<8)
+#define FLAGS_DUMMY_READ		(1<<9)
 
 	/* preemphasis values for the rx side */
 	u16 rx_preemphasis[4];
@@ -142,8 +163,8 @@ struct bnx2x_phy {
 #define	ETH_PHY_XFP_FIBER   0x2
 #define	ETH_PHY_DA_TWINAX   0x3
 #define	ETH_PHY_BASE_T      0x4
-#define	ETH_PHY_KR	    0xf0
-#define	ETH_PHY_CX4	    0xf1
+#define	ETH_PHY_KR          0xf0
+#define	ETH_PHY_CX4         0xf1
 #define	ETH_PHY_NOT_PRESENT 0xff
 
 	/* The address in which version is located*/
@@ -248,6 +269,8 @@ struct link_params {
 /* Output parameters */
 struct link_vars {
 	u8 phy_flags;
+#define PHY_XGXS_FLAG			(1<<0)
+#define PHY_SGMII_FLAG			(1<<1)
 
 	u8 mac_type;
 #define MAC_TYPE_NONE		0
@@ -414,4 +437,7 @@ void bnx2x_pfc_statistic(struct link_params *params, struct link_vars *vars,
 void bnx2x_init_mod_abs_int(struct bnx2x *bp, struct link_vars *vars,
 			    u32 chip_id, u32 shmem_base, u32 shmem2_base,
 			    u8 port);
+
+int bnx2x_sfp_module_detection(struct bnx2x_phy *phy,
+			       struct link_params *params);
 #endif /* BNX2X_LINK_H */

drivers/net/bnx2x/bnx2x_main.c

@@ -8586,7 +8586,10 @@ static void __devinit bnx2x_link_settings_requested(struct bnx2x *bp)
 				return;
 			}
 			break;
+		case PORT_FEATURE_LINK_SPEED_20G:
+			bp->link_params.req_line_speed[idx] = SPEED_20000;
 
+			break;
 		default:
 			BNX2X_ERR("NVRAM config error. "
 				  "BAD link speed link_config 0x%x\n",

drivers/net/bnx2x/bnx2x_reg.h

@@ -981,6 +981,13 @@
 #define IGU_REG_WRITE_DONE_PENDING				 0x130480
 #define MCP_A_REG_MCPR_SCRATCH					 0x3a0000
 #define MCP_REG_MCPR_CPU_PROGRAM_COUNTER			 0x8501c
+#define MCP_REG_MCPR_GP_INPUTS					 0x800c0
+#define MCP_REG_MCPR_GP_OENABLE					 0x800c8
+#define MCP_REG_MCPR_GP_OUTPUTS					 0x800c4
+#define MCP_REG_MCPR_IMC_COMMAND				 0x85900
+#define MCP_REG_MCPR_IMC_DATAREG0				 0x85920
+#define MCP_REG_MCPR_IMC_SLAVE_CONTROL				 0x85904
+#define MCP_REG_MCPR_CPU_PROGRAM_COUNTER			 0x8501c
 #define MCP_REG_MCPR_NVM_ACCESS_ENABLE				 0x86424
 #define MCP_REG_MCPR_NVM_ADDR					 0x8640c
 #define MCP_REG_MCPR_NVM_CFG4					 0x8642c
@@ -1477,11 +1484,37 @@
 /* [RW 1] e1hmf for WOL. If clr WOL signal o the PXP will be send on bit 0
    only. */
 #define MISC_REG_E1HMF_MODE					 0xa5f8
+/* [R 1] Status of four port mode path swap input pin. */
+#define MISC_REG_FOUR_PORT_PATH_SWAP				 0xa75c
+/* [RW 2] 4 port path swap overwrite.[0] - Overwrite control; if it is 0 -
+   the path_swap output is equal to 4 port mode path swap input pin; if it
+   is 1 - the path_swap output is equal to bit[1] of this register; [1] -
+   Overwrite value. If bit[0] of this register is 1 this is the value that
+   receives the path_swap output. Reset on Hard reset. */
+#define MISC_REG_FOUR_PORT_PATH_SWAP_OVWR			 0xa738
+/* [R 1] Status of 4 port mode port swap input pin. */
+#define MISC_REG_FOUR_PORT_PORT_SWAP				 0xa754
+/* [RW 2] 4 port port swap overwrite.[0] - Overwrite control; if it is 0 -
+   the port_swap output is equal to 4 port mode port swap input pin; if it
+   is 1 - the port_swap output is equal to bit[1] of this register; [1] -
+   Overwrite value. If bit[0] of this register is 1 this is the value that
+   receives the port_swap output. Reset on Hard reset. */
+#define MISC_REG_FOUR_PORT_PORT_SWAP_OVWR			 0xa734
 /* [RW 32] Debug only: spare RW register reset by core reset */
 #define MISC_REG_GENERIC_CR_0					 0xa460
 #define MISC_REG_GENERIC_CR_1					 0xa464
 /* [RW 32] Debug only: spare RW register reset by por reset */
 #define MISC_REG_GENERIC_POR_1					 0xa474
+/* [RW 32] Bit[0]: EPIO MODE SEL: Setting this bit to 1 will allow SW/FW to
+   use all of the 32 Extended GPIO pins. Without setting this bit; an EPIO
+   can not be configured as an output. Each output has its output enable in
+   the MCP register space; but this bit needs to be set to make use of that.
+   Bit[3:1] spare. Bit[4]: WCVTMON_PWRDN: Powerdown for Warpcore VTMON. When
+   set to 1 - Powerdown. Bit[5]: WCVTMON_RESETB: Reset for Warpcore VTMON.
+   When set to 0 - vTMON is in reset. Bit[6]: setting this bit will change
+   the i/o to an output and will drive the TimeSync output. Bit[31:7]:
+   spare. Global register. Reset by hard reset. */
+#define MISC_REG_GEN_PURP_HWG					 0xa9a0
 /* [RW 32] GPIO. [31-28] FLOAT port 0; [27-24] FLOAT port 0; When any of
    these bits is written as a '1'; the corresponding SPIO bit will turn off
    it's drivers and become an input. This is the reset state of all GPIO
@@ -1684,6 +1717,14 @@
    in this register. address 0 - timer 1; address 1 - timer 2, ...  address 7 -
    timer 8 */
 #define MISC_REG_SW_TIMER_VAL					 0xa5c0
+/* [R 1] Status of two port mode path swap input pin. */
+#define MISC_REG_TWO_PORT_PATH_SWAP				 0xa758
+/* [RW 2] 2 port swap overwrite.[0] - Overwrite control; if it is 0 - the
+   path_swap output is equal to 2 port mode path swap input pin; if it is 1
+   - the path_swap output is equal to bit[1] of this register; [1] -
+   Overwrite value. If bit[0] of this register is 1 this is the value that
+   receives the path_swap output. Reset on Hard reset. */
+#define MISC_REG_TWO_PORT_PATH_SWAP_OVWR			 0xa72c
 /* [RW 1] Set by the MCP to remember if one or more of the drivers is/are
    loaded; 0-prepare; -unprepare */
 #define MISC_REG_UNPREPARED					 0xa424
@@ -1955,6 +1996,10 @@
 /* [RC 32] Parity register #0 read clear */
 #define NIG_REG_NIG_PRTY_STS_CLR_0				 0x183c0
 #define NIG_REG_NIG_PRTY_STS_CLR_1				 0x183d0
+#define MCPR_IMC_COMMAND_ENABLE					 (1L<<31)
+#define MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT			 16
+#define MCPR_IMC_COMMAND_OPERATION_BITSHIFT			 28
+#define MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT		 8
 /* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic
  * Ethernet header. */
 #define NIG_REG_P0_HDRS_AFTER_BASIC				 0x18038
@@ -6232,6 +6277,10 @@
 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G		0x0C00
 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX	0x0D00
 #define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4	0x0E00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KR	0x0F00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_XFI	0x1B00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_DXGXS	0x1E00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_SFI	0x1F00
 
 
 #define MDIO_REG_BANK_10G_PARALLEL_DETECT		0x8130
@@ -6574,6 +6623,120 @@ Theotherbitsarereservedandshouldbezero*/
 #define PHY84833_CMD_CLEAR_COMPLETE			0x0080
 #define PHY84833_CMD_OPEN_OVERRIDE			0xa5a5
 
+/* Warpcore clause 45 addressing */
+#define MDIO_WC_DEVAD					0x3
+#define MDIO_WC_REG_IEEE0BLK_MIICNTL			0x0
+#define MDIO_WC_REG_IEEE0BLK_AUTONEGNP			0x7
+#define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT0	0x10
+#define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1	0x11
+#define MDIO_WC_REG_PMD_IEEE9BLK_TENGBASE_KR_PMD_CONTROL_REGISTER_150  0x96
+#define MDIO_WC_REG_XGXSBLK0_XGXSCONTROL		0x8000
+#define MDIO_WC_REG_XGXSBLK0_MISCCONTROL1		0x800e
+#define MDIO_WC_REG_XGXSBLK1_DESKEW			0x8010
+#define MDIO_WC_REG_XGXSBLK1_LANECTRL0			0x8015
+#define MDIO_WC_REG_XGXSBLK1_LANECTRL1			0x8016
+#define MDIO_WC_REG_XGXSBLK1_LANECTRL2			0x8017
+#define MDIO_WC_REG_TX0_ANA_CTRL0			0x8061
+#define MDIO_WC_REG_TX1_ANA_CTRL0			0x8071
+#define MDIO_WC_REG_TX2_ANA_CTRL0			0x8081
+#define MDIO_WC_REG_TX3_ANA_CTRL0			0x8091
+#define MDIO_WC_REG_TX0_TX_DRIVER			0x8067
+#define MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET		0x04
+#define MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_MASK			0x00f0
+#define MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET		0x08
+#define MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_MASK				0x0f00
+#define MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET		0x0c
+#define MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_MASK			0x7000
+#define MDIO_WC_REG_TX1_TX_DRIVER			0x8077
+#define MDIO_WC_REG_TX2_TX_DRIVER			0x8087
+#define MDIO_WC_REG_TX3_TX_DRIVER			0x8097
+#define MDIO_WC_REG_RX0_ANARXCONTROL1G			0x80b9
+#define MDIO_WC_REG_RX2_ANARXCONTROL1G			0x80d9
+#define MDIO_WC_REG_RX0_PCI_CTRL			0x80ba
+#define MDIO_WC_REG_RX1_PCI_CTRL			0x80ca
+#define MDIO_WC_REG_RX2_PCI_CTRL			0x80da
+#define MDIO_WC_REG_RX3_PCI_CTRL			0x80ea
+#define MDIO_WC_REG_XGXSBLK2_UNICORE_MODE_10G		0x8104
+#define MDIO_WC_REG_XGXS_STATUS3			0x8129
+#define MDIO_WC_REG_PAR_DET_10G_STATUS			0x8130
+#define MDIO_WC_REG_PAR_DET_10G_CTRL			0x8131
+#define MDIO_WC_REG_XGXS_X2_CONTROL2			0x8141
+#define MDIO_WC_REG_XGXS_RX_LN_SWAP1			0x816B
+#define MDIO_WC_REG_XGXS_TX_LN_SWAP1			0x8169
+#define MDIO_WC_REG_GP2_STATUS_GP_2_0			0x81d0
+#define MDIO_WC_REG_GP2_STATUS_GP_2_1			0x81d1
+#define MDIO_WC_REG_GP2_STATUS_GP_2_2			0x81d2
+#define MDIO_WC_REG_GP2_STATUS_GP_2_3			0x81d3
+#define MDIO_WC_REG_GP2_STATUS_GP_2_4			0x81d4
+#define MDIO_WC_REG_UC_INFO_B0_DEAD_TRAP		0x81EE
+#define MDIO_WC_REG_UC_INFO_B1_VERSION			0x81F0
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE		0x81F2
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE0_OFFSET	0x0
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT	    0x0
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_OPT_LR	    0x1
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_DAC	    0x2
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_XLAUI	    0x3
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_LONG_CH_6G	    0x4
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE1_OFFSET	0x4
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE2_OFFSET	0x8
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE3_OFFSET	0xc
+#define MDIO_WC_REG_UC_INFO_B1_CRC			0x81FE
+#define MDIO_WC_REG_DSC_SMC				0x8213
+#define MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0		0x821e
+#define MDIO_WC_REG_TX_FIR_TAP				0x82e2
+#define MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET		0x00
+#define MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_MASK			0x000f
+#define MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET		0x04
+#define MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_MASK		0x03f0
+#define MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET		0x0a
+#define MDIO_WC_REG_TX_FIR_TAP_POST_TAP_MASK		0x7c00
+#define MDIO_WC_REG_TX_FIR_TAP_ENABLE		0x8000
+#define MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL	0x82e3
+#define MDIO_WC_REG_CL72_USERB0_CL72_OS_DEF_CTRL	0x82e6
+#define MDIO_WC_REG_CL72_USERB0_CL72_BR_DEF_CTRL	0x82e7
+#define MDIO_WC_REG_CL72_USERB0_CL72_2P5_DEF_CTRL	0x82e8
+#define MDIO_WC_REG_CL72_USERB0_CL72_MISC4_CONTROL	0x82ec
+#define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1		0x8300
+#define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2		0x8301
+#define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3		0x8302
+#define MDIO_WC_REG_SERDESDIGITAL_STATUS1000X1		0x8304
+#define MDIO_WC_REG_SERDESDIGITAL_MISC1			0x8308
+#define MDIO_WC_REG_SERDESDIGITAL_MISC2			0x8309
+#define MDIO_WC_REG_DIGITAL3_UP1			0x8329
+#define MDIO_WC_REG_DIGITAL4_MISC3			0x833c
+#define MDIO_WC_REG_DIGITAL5_MISC6			0x8345
+#define MDIO_WC_REG_DIGITAL5_MISC7			0x8349
+#define MDIO_WC_REG_DIGITAL5_ACTUAL_SPEED		0x834e
+#define MDIO_WC_REG_CL49_USERB0_CTRL			0x8368
+#define MDIO_WC_REG_TX66_CONTROL			0x83b0
+#define MDIO_WC_REG_RX66_CONTROL			0x83c0
+#define MDIO_WC_REG_RX66_SCW0				0x83c2
+#define MDIO_WC_REG_RX66_SCW1				0x83c3
+#define MDIO_WC_REG_RX66_SCW2				0x83c4
+#define MDIO_WC_REG_RX66_SCW3				0x83c5
+#define MDIO_WC_REG_RX66_SCW0_MASK			0x83c6
+#define MDIO_WC_REG_RX66_SCW1_MASK			0x83c7
+#define MDIO_WC_REG_RX66_SCW2_MASK			0x83c8
+#define MDIO_WC_REG_RX66_SCW3_MASK			0x83c9
+#define MDIO_WC_REG_FX100_CTRL1				0x8400
+#define MDIO_WC_REG_FX100_CTRL3				0x8402
+
+#define MDIO_WC_REG_MICROBLK_CMD			0xffc2
+#define MDIO_WC_REG_MICROBLK_DL_STATUS			0xffc5
+#define MDIO_WC_REG_MICROBLK_CMD3			0xffcc
+
+#define MDIO_WC_REG_AERBLK_AER				0xffde
+#define MDIO_WC_REG_COMBO_IEEE0_MIICTRL			0xffe0
+#define MDIO_WC_REG_COMBO_IEEE0_MIIISTAT		0xffe1
+
+#define MDIO_WC0_XGXS_BLK2_LANE_RESET			0x810A
+#define MDIO_WC0_XGXS_BLK2_LANE_RESET_RX_BITSHIFT	0
+#define MDIO_WC0_XGXS_BLK2_LANE_RESET_TX_BITSHIFT	4
+
+#define MDIO_WC0_XGXS_BLK6_XGXS_X2_CONTROL2		0x8141
+
+#define DIGITAL5_ACTUAL_SPEED_TX_MASK			0x003f
+
 #define IGU_FUNC_BASE			0x0400
 
 #define IGU_ADDR_MSIX			0x0000