Merge branches 'depends/rmk/io', 'depends/rmk/l2x0' and 'depends/rmk/gpio' into highbank/soc

Documentation/devicetree/bindings/arm/l2cc.txt

@@ -0,0 +1,44 @@
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+	"arm,pl310-cache"
+	"arm,l220-cache"
+	"arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+  registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Minimum valid values are 1. Controllers
+  without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Controllers without setup latency control
+  should use 0. Controllers without separate read and write Tag RAM latency
+  values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+  filter. Addresses in the filter window are directed to the M1 port. Other
+  addresses will go to the M0 port.
+- interrupts : 1 combined interrupt.
+
+Example:
+
+L2: cache-controller {
+        compatible = "arm,pl310-cache";
+        reg = <0xfff12000 0x1000>;
+        arm,data-latency = <1 1 1>;
+        arm,tag-latency = <2 2 2>;
+        arm,filter-latency = <0x80000000 0x8000000>;
+        cache-unified;
+        cache-level = <2>;
+	interrupts = <45>;
+};

arch/arm/Kconfig

@@ -835,6 +835,7 @@ config ARCH_U300
 	select CLKDEV_LOOKUP
 	select HAVE_MACH_CLKDEV
 	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
 

arch/arm/common/scoop.c

@@ -12,11 +12,11 @@
  */
 
 #include <linux/device.h>
+#include <linux/gpio.h>
 #include <linux/string.h>
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <asm/gpio.h>
 #include <asm/hardware/scoop.h>
 
 /* PCMCIA to Scoop linkage

arch/arm/include/asm/ecard.h

@@ -161,7 +161,6 @@ struct expansion_card {
 
 	/* Private internal data */
 	const char		*card_desc;	/* Card description		*/
-	CONST unsigned int	podaddr;	/* Base Linux address for card	*/
 	CONST loader_t		loader;		/* loader program */
 	u64			dma_mask;
 };

arch/arm/include/asm/gpio.h

@@ -4,4 +4,23 @@
 /* not all ARM platforms necessarily support this API ... */
 #include <mach/gpio.h>
 
+#ifndef __ARM_GPIOLIB_COMPLEX
+/* Note: this may rely upon the value of ARCH_NR_GPIOS set in mach/gpio.h */
+#include <asm-generic/gpio.h>
+
+/* The trivial gpiolib dispatchers */
+#define gpio_get_value  __gpio_get_value
+#define gpio_set_value  __gpio_set_value
+#define gpio_cansleep   __gpio_cansleep
+#endif
+
+/*
+ * Provide a default gpio_to_irq() which should satisfy every case.
+ * However, some platforms want to do this differently, so allow them
+ * to override it.
+ */
+#ifndef gpio_to_irq
+#define gpio_to_irq	__gpio_to_irq
+#endif
+
 #endif /* _ARCH_ARM_GPIO_H */

arch/arm/include/asm/hardware/cache-l2x0.h

@@ -52,6 +52,8 @@
 #define L2X0_LOCKDOWN_WAY_D_BASE	0x900
 #define L2X0_LOCKDOWN_WAY_I_BASE	0x904
 #define L2X0_LOCKDOWN_STRIDE		0x08
+#define L2X0_ADDR_FILTER_START		0xC00
+#define L2X0_ADDR_FILTER_END		0xC04
 #define L2X0_TEST_OPERATION		0xF00
 #define L2X0_LINE_DATA			0xF10
 #define L2X0_LINE_TAG			0xF30
@@ -65,8 +67,23 @@
 #define L2X0_CACHE_ID_PART_MASK		(0xf << 6)
 #define L2X0_CACHE_ID_PART_L210		(1 << 6)
 #define L2X0_CACHE_ID_PART_L310		(3 << 6)
+#define L2X0_CACHE_ID_RTL_MASK          0x3f
+#define L2X0_CACHE_ID_RTL_R0P0          0x0
+#define L2X0_CACHE_ID_RTL_R1P0          0x2
+#define L2X0_CACHE_ID_RTL_R2P0          0x4
+#define L2X0_CACHE_ID_RTL_R3P0          0x5
+#define L2X0_CACHE_ID_RTL_R3P1          0x6
+#define L2X0_CACHE_ID_RTL_R3P2          0x8
 
 #define L2X0_AUX_CTRL_MASK			0xc0000fff
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT	0
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK	0x7
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT	3
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK	(0x7 << 3)
+#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT		6
+#define L2X0_AUX_CTRL_TAG_LATENCY_MASK		(0x7 << 6)
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT	9
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK	(0x7 << 9)
 #define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT	16
 #define L2X0_AUX_CTRL_WAY_SIZE_SHIFT		17
 #define L2X0_AUX_CTRL_WAY_SIZE_MASK		(0x7 << 17)
@@ -77,8 +94,33 @@
 #define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT	29
 #define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT		30
 
+#define L2X0_LATENCY_CTRL_SETUP_SHIFT	0
+#define L2X0_LATENCY_CTRL_RD_SHIFT	4
+#define L2X0_LATENCY_CTRL_WR_SHIFT	8
+
+#define L2X0_ADDR_FILTER_EN		1
+
 #ifndef __ASSEMBLY__
 extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
+extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
+
+struct l2x0_regs {
+	unsigned long phy_base;
+	unsigned long aux_ctrl;
+	/*
+	 * Whether the following registers need to be saved/restored
+	 * depends on platform
+	 */
+	unsigned long tag_latency;
+	unsigned long data_latency;
+	unsigned long filter_start;
+	unsigned long filter_end;
+	unsigned long prefetch_ctrl;
+	unsigned long pwr_ctrl;
+};
+
+extern struct l2x0_regs l2x0_saved_regs;
+
 #endif
 
 #endif

arch/arm/include/asm/hardware/iop3xx-gpio.h

@@ -28,6 +28,8 @@
 #include <mach/hardware.h>
 #include <asm-generic/gpio.h>
 
+#define __ARM_GPIOLIB_COMPLEX
+
 #define IOP3XX_N_GPIOS	8
 
 static inline int gpio_get_value(unsigned gpio)

arch/arm/include/asm/io.h

@@ -109,6 +109,27 @@ static inline void __iomem *__typesafe_io(unsigned long addr)
  */
 #include <mach/io.h>
 
+/*
+ * This is the limit of PC card/PCI/ISA IO space, which is by default
+ * 64K if we have PC card, PCI or ISA support.  Otherwise, default to
+ * zero to prevent ISA/PCI drivers claiming IO space (and potentially
+ * oopsing.)
+ *
+ * Only set this larger if you really need inb() et.al. to operate over
+ * a larger address space.  Note that SOC_COMMON ioremaps each sockets
+ * IO space area, and so inb() et.al. must be defined to operate as per
+ * readb() et.al. on such platforms.
+ */
+#ifndef IO_SPACE_LIMIT
+#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff)
+#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffff)
+#else
+#define IO_SPACE_LIMIT ((resource_size_t)0)
+#endif
+#endif
+
 /*
  *  IO port access primitives
  *  -------------------------

arch/arm/include/asm/outercache.h

@@ -34,6 +34,7 @@ struct outer_cache_fns {
 	void (*sync)(void);
 #endif
 	void (*set_debug)(unsigned long);
+	void (*resume)(void);
 };
 
 #ifdef CONFIG_OUTER_CACHE
@@ -74,6 +75,12 @@ static inline void outer_disable(void)
 		outer_cache.disable();
 }
 
+static inline void outer_resume(void)
+{
+	if (outer_cache.resume)
+		outer_cache.resume();
+}
+
 #else
 
 static inline void outer_inv_range(phys_addr_t start, phys_addr_t end)

arch/arm/kernel/asm-offsets.c

@@ -20,6 +20,7 @@
 #include <asm/thread_info.h>
 #include <asm/memory.h>
 #include <asm/procinfo.h>
+#include <asm/hardware/cache-l2x0.h>
 #include <linux/kbuild.h>
 
 /*
@@ -92,6 +93,17 @@ int main(void)
   DEFINE(S_OLD_R0,		offsetof(struct pt_regs, ARM_ORIG_r0));
   DEFINE(S_FRAME_SIZE,		sizeof(struct pt_regs));
   BLANK();
+#ifdef CONFIG_CACHE_L2X0
+  DEFINE(L2X0_R_PHY_BASE,	offsetof(struct l2x0_regs, phy_base));
+  DEFINE(L2X0_R_AUX_CTRL,	offsetof(struct l2x0_regs, aux_ctrl));
+  DEFINE(L2X0_R_TAG_LATENCY,	offsetof(struct l2x0_regs, tag_latency));
+  DEFINE(L2X0_R_DATA_LATENCY,	offsetof(struct l2x0_regs, data_latency));
+  DEFINE(L2X0_R_FILTER_START,	offsetof(struct l2x0_regs, filter_start));
+  DEFINE(L2X0_R_FILTER_END,	offsetof(struct l2x0_regs, filter_end));
+  DEFINE(L2X0_R_PREFETCH_CTRL,	offsetof(struct l2x0_regs, prefetch_ctrl));
+  DEFINE(L2X0_R_PWR_CTRL,	offsetof(struct l2x0_regs, pwr_ctrl));
+  BLANK();
+#endif
 #ifdef CONFIG_CPU_HAS_ASID
   DEFINE(MM_CONTEXT_ID,		offsetof(struct mm_struct, context.id));
   BLANK();

arch/arm/kernel/ecard.c

@@ -237,7 +237,7 @@ static void ecard_init_pgtables(struct mm_struct *mm)
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (IO_SIZE / PGDIR_SIZE));
 
-	src_pgd = pgd_offset(mm, EASI_BASE);
+	src_pgd = pgd_offset(mm, (unsigned long)EASI_BASE);
 	dst_pgd = pgd_offset(mm, EASI_START);
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
@@ -674,44 +674,37 @@ static int __init ecard_probeirqhw(void)
 #define ecard_probeirqhw() (0)
 #endif
 
-#ifndef IO_EC_MEMC8_BASE
-#define IO_EC_MEMC8_BASE 0
-#endif
-
-static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
+static void __iomem *__ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
 {
-	unsigned long address = 0;
+	void __iomem *address = NULL;
 	int slot = ec->slot_no;
 
 	if (ec->slot_no == 8)
-		return IO_EC_MEMC8_BASE;
+		return ECARD_MEMC8_BASE;
 
 	ectcr &= ~(1 << slot);
 
 	switch (type) {
 	case ECARD_MEMC:
 		if (slot < 4)
-			address = IO_EC_MEMC_BASE + (slot << 12);
+			address = ECARD_MEMC_BASE + (slot << 14);
 		break;
 
 	case ECARD_IOC:
 		if (slot < 4)
-			address = IO_EC_IOC_BASE + (slot << 12);
-#ifdef IO_EC_IOC4_BASE
+			address = ECARD_IOC_BASE + (slot << 14);
 		else
-			address = IO_EC_IOC4_BASE + ((slot - 4) << 12);
-#endif
+			address = ECARD_IOC4_BASE + ((slot - 4) << 14);
 		if (address)
-			address +=  speed << 17;
+			address += speed << 19;
 		break;
 
-#ifdef IO_EC_EASI_BASE
 	case ECARD_EASI:
-		address = IO_EC_EASI_BASE + (slot << 22);
+		address = ECARD_EASI_BASE + (slot << 24);
 		if (speed == ECARD_FAST)
 			ectcr |= 1 << slot;
 		break;
-#endif
+
 	default:
 		break;
 	}
@@ -990,6 +983,7 @@ ecard_probe(int slot, card_type_t type)
 	ecard_t **ecp;
 	ecard_t *ec;
 	struct ex_ecid cid;
+	void __iomem *addr;
 	int i, rc;
 
 	ec = ecard_alloc_card(type, slot);
@@ -999,7 +993,7 @@ ecard_probe(int slot, card_type_t type)
 	}
 
 	rc = -ENODEV;
-	if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0)
+	if ((addr = __ecard_address(ec, type, ECARD_SYNC)) == NULL)
 		goto nodev;
 
 	cid.r_zero = 1;
@@ -1019,7 +1013,7 @@ ecard_probe(int slot, card_type_t type)
 	ec->cid.fiqmask = cid.r_fiqmask;
 	ec->cid.fiqoff  = ecard_gets24(cid.r_fiqoff);
 	ec->fiqaddr	=
-	ec->irqaddr	= (void __iomem *)ioaddr(ec->podaddr);
+	ec->irqaddr	= addr;
 
 	if (ec->cid.is) {
 		ec->irqmask = ec->cid.irqmask;
@@ -1048,10 +1042,8 @@ ecard_probe(int slot, card_type_t type)
 		set_irq_flags(ec->irq, IRQF_VALID);
 	}
 
-#ifdef IO_EC_MEMC8_BASE
 	if (slot == 8)
 		ec->irq = 11;
-#endif
 #ifdef CONFIG_ARCH_RPC
 	/* On RiscPC, only first two slots have DMA capability */
 	if (slot < 2)
@@ -1097,9 +1089,7 @@ static int __init ecard_init(void)
 			ecard_probe(slot, ECARD_IOC);
 	}
 
-#ifdef IO_EC_MEMC8_BASE
 	ecard_probe(8, ECARD_IOC);
-#endif
 
 	irqhw = ecard_probeirqhw();
 

arch/arm/mach-at91/at91cap9_devices.c

@@ -16,6 +16,7 @@
 #include <asm/mach/irq.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -23,7 +24,6 @@
 
 #include <mach/board.h>
 #include <mach/cpu.h>
-#include <mach/gpio.h>
 #include <mach/at91cap9.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91rm9200_devices.c

@@ -14,11 +14,11 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200.h>
 #include <mach/at91rm9200_mc.h>
 

arch/arm/mach-at91/at91sam9260_devices.c

@@ -13,11 +13,11 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 #include <mach/at91sam9260.h>
 #include <mach/at91sam9260_matrix.h>

arch/arm/mach-at91/at91sam9261_devices.c

@@ -14,6 +14,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -21,7 +22,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9261.h>
 #include <mach/at91sam9261_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91sam9263_devices.c

@@ -13,6 +13,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -20,7 +21,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9263.h>
 #include <mach/at91sam9263_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -13,6 +13,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 #include <linux/atmel-mci.h>
@@ -21,7 +22,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9g45.h>
 #include <mach/at91sam9g45_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -10,6 +10,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -17,7 +18,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9rl.h>
 #include <mach/at91sam9rl_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/board-1arm.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -34,7 +35,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -25,6 +25,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -43,7 +44,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-cam60.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"

arch/arm/mach-at91/board-cap9adk.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 #include <asm/mach/map.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-carmeva.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-cpu9krea.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91sam9260_matrix.h>
 

arch/arm/mach-at91/board-cpuat91.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -36,7 +37,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 #include <mach/cpu.h>
 

arch/arm/mach-at91/board-csb337.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-csb637.c

@@ -20,6 +20,7 @@
 
 #include <linux/types.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
@@ -35,7 +36,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-eb9200.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-ecbat91.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-kafa.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -34,7 +35,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-kb9202.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 #include <mach/at91rm9200_mc.h>
 

arch/arm/mach-at91/board-neocore926.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -44,7 +45,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"

arch/arm/mach-at91/board-picotux200.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-qil-a9260.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-rm9200dk.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-rm9200ek.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-sam9-l9260.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"

arch/arm/mach-at91/board-sam9260ek.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9261ek.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -45,7 +46,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9263ek.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -44,7 +45,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9g20ek.c

@@ -18,6 +18,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/system_rev.h>
 

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -14,6 +14,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9rlek.c

@@ -8,6 +8,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -30,7 +31,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-usb-a9260.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-usb-a9263.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-yl-9200.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -43,7 +44,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 #include <mach/cpu.h>
 

arch/arm/mach-at91/gpio.c

@@ -11,6 +11,7 @@
 
 #include <linux/clk.h>
 #include <linux/errno.h>
+#include <linux/gpio.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/debugfs.h>
@@ -22,9 +23,6 @@
 
 #include <mach/hardware.h>
 #include <mach/at91_pio.h>
-#include <mach/gpio.h>
-
-#include <asm/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/include/mach/gpio.h

@@ -214,11 +214,6 @@ extern void at91_gpio_resume(void);
  */
 
 #include <asm/errno.h>
-#include <asm-generic/gpio.h>		/* cansleep wrappers */
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
 
 #define gpio_to_irq(gpio) (gpio)
 #define irq_to_gpio(irq)  (irq)

arch/arm/mach-at91/leds.c

@@ -9,13 +9,13 @@
  * 2 of the License, or (at your option) any later version.
 */
 
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 
 /* ------------------------------------------------------------------------- */

arch/arm/mach-at91/pm.c

@@ -10,6 +10,7 @@
  * (at your option) any later version.
  */
 
+#include <linux/gpio.h>
 #include <linux/suspend.h>
 #include <linux/sched.h>
 #include <linux/proc_fs.h>
@@ -25,7 +26,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/at91_pmc.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-davinci/Makefile

@@ -5,7 +5,7 @@
 
 # Common objects
 obj-y 			:= time.o clock.o serial.o io.o psc.o \
-			   gpio.o dma.o usb.o common.o sram.o aemif.o
+			   dma.o usb.o common.o sram.o aemif.o
 
 obj-$(CONFIG_DAVINCI_MUX)		+= mux.o
 
@@ -17,7 +17,6 @@ obj-$(CONFIG_ARCH_DAVINCI_DM365)	+= dm365.o devices.o
 obj-$(CONFIG_ARCH_DAVINCI_DA830)        += da830.o devices-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_DA850)        += da850.o devices-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_TNETV107X)    += tnetv107x.o devices-tnetv107x.o
-obj-$(CONFIG_ARCH_DAVINCI_TNETV107X)    += gpio-tnetv107x.o
 
 obj-$(CONFIG_AINTC)			+= irq.o
 obj-$(CONFIG_CP_INTC)			+= cp_intc.o

arch/arm/mach-davinci/da830.c

@@ -8,6 +8,7 @@
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/clk.h>
 
@@ -19,7 +20,7 @@
 #include <mach/common.h>
 #include <mach/time.h>
 #include <mach/da8xx.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/da850.c

@@ -11,6 +11,7 @@
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/clk.h>
 #include <linux/platform_device.h>
@@ -27,7 +28,7 @@
 #include <mach/da8xx.h>
 #include <mach/cpufreq.h>
 #include <mach/pm.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm355.c

@@ -13,7 +13,6 @@
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/gpio.h>
 
 #include <linux/spi/spi.h>
 
@@ -30,6 +29,7 @@
 #include <mach/common.h>
 #include <mach/asp.h>
 #include <mach/spi.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm365.c

@@ -17,7 +17,6 @@
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/gpio.h>
 #include <linux/spi/spi.h>
 
 #include <asm/mach/map.h>
@@ -34,7 +33,7 @@
 #include <mach/asp.h>
 #include <mach/keyscan.h>
 #include <mach/spi.h>
-
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm644x.c

@@ -12,7 +12,6 @@
 #include <linux/clk.h>
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 
@@ -26,6 +25,7 @@
 #include <mach/serial.h>
 #include <mach/common.h>
 #include <mach/asp.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm646x.c

@@ -13,7 +13,6 @@
 #include <linux/clk.h>
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 
@@ -27,6 +26,7 @@
 #include <mach/serial.h>
 #include <mach/common.h>
 #include <mach/asp.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/include/mach/gpio-davinci.h

@@ -0,0 +1,91 @@
+/*
+ * TI DaVinci GPIO Support
+ *
+ * Copyright (c) 2006 David Brownell
+ * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef	__DAVINCI_DAVINCI_GPIO_H
+#define	__DAVINCI_DAVINCI_GPIO_H
+
+#include <linux/io.h>
+#include <linux/spinlock.h>
+
+#include <asm-generic/gpio.h>
+
+#include <mach/irqs.h>
+#include <mach/common.h>
+
+#define DAVINCI_GPIO_BASE 0x01C67000
+
+enum davinci_gpio_type {
+	GPIO_TYPE_DAVINCI = 0,
+	GPIO_TYPE_TNETV107X,
+};
+
+/*
+ * basic gpio routines
+ *
+ * board-specific init should be done by arch/.../.../board-XXX.c (maybe
+ * initializing banks together) rather than boot loaders; kexec() won't
+ * go through boot loaders.
+ *
+ * the gpio clock will be turned on when gpios are used, and you may also
+ * need to pay attention to PINMUX registers to be sure those pins are
+ * used as gpios, not with other peripherals.
+ *
+ * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation,
+ * and maybe for later updates, code may write GPIO(N).  These may be
+ * all 1.8V signals, all 3.3V ones, or a mix of the two.  A given chip
+ * may not support all the GPIOs in that range.
+ *
+ * GPIOs can also be on external chips, numbered after the ones built-in
+ * to the DaVinci chip.  For now, they won't be usable as IRQ sources.
+ */
+#define	GPIO(X)		(X)		/* 0 <= X <= (DAVINCI_N_GPIO - 1) */
+
+/* Convert GPIO signal to GPIO pin number */
+#define GPIO_TO_PIN(bank, gpio)	(16 * (bank) + (gpio))
+
+struct davinci_gpio_controller {
+	struct gpio_chip	chip;
+	int			irq_base;
+	spinlock_t		lock;
+	void __iomem		*regs;
+	void __iomem		*set_data;
+	void __iomem		*clr_data;
+	void __iomem		*in_data;
+};
+
+/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
+ * with constant parameters; or in outlined code they execute at runtime.
+ *
+ * You'd access the controller directly when reading or writing more than
+ * one gpio value at a time, and to support wired logic where the value
+ * being driven by the cpu need not match the value read back.
+ *
+ * These are NOT part of the cross-platform GPIO interface
+ */
+static inline struct davinci_gpio_controller *
+__gpio_to_controller(unsigned gpio)
+{
+	struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
+	int index = gpio / 32;
+
+	if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
+		return NULL;
+
+	return ctlrs + index;
+}
+
+static inline u32 __gpio_mask(unsigned gpio)
+{
+	return 1 << (gpio % 32);
+}
+
+#endif	/* __DAVINCI_DAVINCI_GPIO_H */

arch/arm/mach-davinci/include/mach/gpio.h

@@ -13,80 +13,10 @@
 #ifndef	__DAVINCI_GPIO_H
 #define	__DAVINCI_GPIO_H
 
-#include <linux/io.h>
-#include <linux/spinlock.h>
-
 #include <asm-generic/gpio.h>
 
-#include <mach/irqs.h>
-#include <mach/common.h>
-
-#define DAVINCI_GPIO_BASE 0x01C67000
-
-enum davinci_gpio_type {
-	GPIO_TYPE_DAVINCI = 0,
-	GPIO_TYPE_TNETV107X,
-};
-
-/*
- * basic gpio routines
- *
- * board-specific init should be done by arch/.../.../board-XXX.c (maybe
- * initializing banks together) rather than boot loaders; kexec() won't
- * go through boot loaders.
- *
- * the gpio clock will be turned on when gpios are used, and you may also
- * need to pay attention to PINMUX registers to be sure those pins are
- * used as gpios, not with other peripherals.
- *
- * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation,
- * and maybe for later updates, code may write GPIO(N).  These may be
- * all 1.8V signals, all 3.3V ones, or a mix of the two.  A given chip
- * may not support all the GPIOs in that range.
- *
- * GPIOs can also be on external chips, numbered after the ones built-in
- * to the DaVinci chip.  For now, they won't be usable as IRQ sources.
- */
-#define	GPIO(X)		(X)		/* 0 <= X <= (DAVINCI_N_GPIO - 1) */
-
-/* Convert GPIO signal to GPIO pin number */
-#define GPIO_TO_PIN(bank, gpio)	(16 * (bank) + (gpio))
-
-struct davinci_gpio_controller {
-	struct gpio_chip	chip;
-	int			irq_base;
-	spinlock_t		lock;
-	void __iomem		*regs;
-	void __iomem		*set_data;
-	void __iomem		*clr_data;
-	void __iomem		*in_data;
-};
-
-/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
- * with constant parameters; or in outlined code they execute at runtime.
- *
- * You'd access the controller directly when reading or writing more than
- * one gpio value at a time, and to support wired logic where the value
- * being driven by the cpu need not match the value read back.
- *
- * These are NOT part of the cross-platform GPIO interface
- */
-static inline struct davinci_gpio_controller *
-__gpio_to_controller(unsigned gpio)
-{
-	struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
-	int index = gpio / 32;
-
-	if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
-		return NULL;
-
-	return ctlrs + index;
-}
-
-static inline u32 __gpio_mask(unsigned gpio)
-{
-	return 1 << (gpio % 32);
-}
+/* The inline versions use the static inlines in the driver header */
+#include "gpio-davinci.h"
 
 /*
  * The get/set/clear functions will inline when called with constant
@@ -147,11 +77,6 @@ static inline int gpio_cansleep(unsigned gpio)
 		return __gpio_cansleep(gpio);
 }
 
-static inline int gpio_to_irq(unsigned gpio)
-{
-	return __gpio_to_irq(gpio);
-}
-
 static inline int irq_to_gpio(unsigned irq)
 {
 	/* don't support the reverse mapping */

arch/arm/mach-davinci/tnetv107x.c

@@ -12,6 +12,7 @@
  * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/clk.h>
@@ -27,9 +28,9 @@
 #include <mach/psc.h>
 #include <mach/cp_intc.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
 #include <mach/hardware.h>
 #include <mach/tnetv107x.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-ebsa110/include/mach/io.h

@@ -13,8 +13,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffff
-
 u8 __inb8(unsigned int port);
 void __outb8(u8  val, unsigned int port);
 

arch/arm/mach-ep93xx/core.c

@@ -38,6 +38,7 @@
 #include <mach/fb.h>
 #include <mach/ep93xx_keypad.h>
 #include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>

arch/arm/mach-ep93xx/edb93xx.c

@@ -37,6 +37,7 @@
 #include <mach/hardware.h>
 #include <mach/fb.h>
 #include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-ep93xx/include/mach/gpio.h → arch/arm/mach-ep93xx/include/mach/gpio-ep93xx.h

@@ -1,9 +1,7 @@
-/*
- * arch/arm/mach-ep93xx/include/mach/gpio.h
- */
+/* Include file for the EP93XX GPIO controller machine specifics */
 
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
+#ifndef __GPIO_EP93XX_H
+#define __GPIO_EP93XX_H
 
 /* GPIO port A.  */
 #define EP93XX_GPIO_LINE_A(x)		((x) + 0)
@@ -99,22 +97,4 @@
 /* maximum value for irq capable line identifiers */
 #define EP93XX_GPIO_LINE_MAX_IRQ	EP93XX_GPIO_LINE_F(7)
 
-/* new generic GPIO API - see Documentation/gpio.txt */
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-
-/*
- * Map GPIO A0..A7  (0..7)  to irq 64..71,
- *          B0..B7  (7..15) to irq 72..79, and
- *          F0..F7 (16..24) to irq 80..87.
- */
-#define gpio_to_irq(gpio)	\
-	(((gpio) <= EP93XX_GPIO_LINE_MAX_IRQ) ? (64 + (gpio)) : -EINVAL)
-
-#define irq_to_gpio(irq)	((irq) - gpio_to_irq(0))
-
-#endif
+#endif /* __GPIO_EP93XX_H */

arch/arm/mach-ep93xx/simone.c

@@ -18,12 +18,12 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/hardware.h>
 #include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-ep93xx/snappercl15.c

@@ -20,7 +20,6 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 #include <linux/fb.h>
@@ -30,6 +29,7 @@
 
 #include <mach/hardware.h>
 #include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-exynos4/include/mach/gpio.h

@@ -13,11 +13,6 @@
 #ifndef __ASM_ARCH_GPIO_H
 #define __ASM_ARCH_GPIO_H __FILE__
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* Practically, GPIO banks up to GPZ are the configurable gpio banks */
 
 /* GPIO bank sizes */
@@ -151,6 +146,4 @@ enum s5p_gpio_number {
 #define ARCH_NR_GPIOS		(EXYNOS4_GPZ(EXYNOS4_GPIO_Z_NR) +	\
 				 CONFIG_SAMSUNG_GPIO_EXTRA + 1)
 
-#include <asm-generic/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */

arch/arm/mach-footbridge/include/mach/io.h

@@ -23,8 +23,6 @@
 #define PCIO_SIZE       0x00100000
 #define PCIO_BASE       MMU_IO(0xff000000, 0x7c000000)
 
-#define IO_SPACE_LIMIT 0xffff
-
 /*
  * Translation of various region addresses to virtual addresses
  */

arch/arm/mach-gemini/include/mach/gpio.h

@@ -13,11 +13,6 @@
 #define __MACH_GPIO_H__
 
 #include <mach/irqs.h>
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
 
 #define gpio_to_irq(x)	((x) + GPIO_IRQ_BASE)
 #define irq_to_gpio(x)	((x) - GPIO_IRQ_BASE)

arch/arm/mach-imx/iomux-imx31.c

@@ -17,13 +17,12 @@
  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
  * MA 02110-1301, USA.
  */
-
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <mach/hardware.h>
-#include <mach/gpio.h>
 #include <mach/iomux-mx3.h>
 
 /*

arch/arm/mach-imx/mach-mx27ads.c

@@ -13,7 +13,7 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
-
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/map.h>
@@ -27,7 +27,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
-#include <mach/gpio.h>
 #include <mach/iomux-mx27.h>
 
 #include "devices-imx27.h"

arch/arm/mach-integrator/include/mach/io.h

@@ -20,8 +20,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffff
-
 /*
  * WARNING: this has to mirror definitions in platform.h
  */

arch/arm/mach-ixp2000/core.c

@@ -13,7 +13,7 @@
  * License version 2. This program is licensed "as is" without any 
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
@@ -39,7 +39,7 @@
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
 
-#include <mach/gpio.h>
+#include <mach/gpio-ixp2000.h>
 
 static DEFINE_SPINLOCK(ixp2000_slowport_lock);
 static unsigned long ixp2000_slowport_irq_flags;

arch/arm/mach-ixp2000/include/mach/gpio.h → arch/arm/mach-ixp2000/include/mach/gpio-ixp2000.h

@@ -3,7 +3,7 @@
  *
  * Copyright (C) 2002 Intel Corporation.
  *
- * This program is free software, you can redistribute it and/or modify 
+ * This program is free software, you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
@@ -11,7 +11,7 @@
 /*
  * IXP2000 GPIO in/out, edge/level detection for IRQs:
  * IRQs are generated on Falling-edge, Rising-Edge, Level-low, Level-High
- * or both Falling-edge and Rising-edge.  
+ * or both Falling-edge and Rising-edge.
  * This must be called *before* the corresponding IRQ is registerd.
  * Use this instead of directly setting the GPIO registers.
  * GPIOs may also be used as GPIOs (e.g. for emulating i2c/smb)

arch/arm/mach-ixp2000/ixdp2x00.c

@@ -14,6 +14,7 @@
  *  Free Software Foundation;  either version 2 of the  License, or (at your
  *  option) any later version.
  */
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/mm.h>
@@ -40,8 +41,7 @@
 #include <asm/mach/flash.h>
 #include <asm/mach/arch.h>
 
-#include <mach/gpio.h>
-
+#include <mach/gpio-ixp2000.h>
 
 /*************************************************************************
  * IXDP2x00 IRQ Initialization

arch/arm/mach-ixp4xx/dsmg600-setup.c

@@ -16,7 +16,7 @@
  * Author: Rod Whitby <rod@whitby.id.au>
  * Maintainers: http://www.nslu2-linux.org/
  */
-
+#include <linux/gpio.h>
 #include <linux/irq.h>
 #include <linux/jiffies.h>
 #include <linux/timer.h>
@@ -31,7 +31,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
-#include <asm/gpio.h>
 
 #define DSMG600_SDA_PIN		5
 #define DSMG600_SCL_PIN		4

arch/arm/mach-ixp4xx/fsg-setup.c

@@ -14,7 +14,7 @@
  * Maintainers: http://www.nslu2-linux.org/
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/if_ether.h>
 #include <linux/irq.h>
 #include <linux/serial.h>
@@ -27,7 +27,6 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
-#include <asm/gpio.h>
 
 #define FSG_SDA_PIN		12
 #define FSG_SCL_PIN		13

arch/arm/mach-ixp4xx/include/mach/gpio.h

@@ -28,6 +28,8 @@
 #include <linux/kernel.h>
 #include <mach/hardware.h>
 
+#define __ARM_GPIOLIB_COMPLEX
+
 static inline int gpio_request(unsigned gpio, const char *label)
 {
 	return 0;
@@ -70,6 +72,7 @@ static inline void gpio_set_value(unsigned gpio, int value)
 #include <asm-generic/gpio.h>			/* cansleep wrappers */
 
 extern int gpio_to_irq(int gpio);
+#define gpio_to_irq gpio_to_irq
 extern int irq_to_gpio(unsigned int irq);
 
 #endif

arch/arm/mach-ixp4xx/include/mach/io.h

@@ -17,8 +17,6 @@
 
 #include <mach/hardware.h>
 
-#define IO_SPACE_LIMIT 0x0000ffff
-
 extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
 extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
 

arch/arm/mach-ixp4xx/nas100d-setup.c

@@ -17,7 +17,7 @@
  * Maintainers: http://www.nslu2-linux.org/
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/if_ether.h>
 #include <linux/irq.h>
 #include <linux/jiffies.h>
@@ -32,7 +32,6 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
-#include <asm/gpio.h>
 
 #define NAS100D_SDA_PIN		5
 #define NAS100D_SCL_PIN		6

arch/arm/mach-ixp4xx/nslu2-setup.c

@@ -16,7 +16,7 @@
  * Maintainers: http://www.nslu2-linux.org/
  *
  */
-
+#include <linux/gpio.h>
 #include <linux/if_ether.h>
 #include <linux/irq.h>
 #include <linux/serial.h>
@@ -30,7 +30,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
-#include <asm/gpio.h>
 
 #define NSLU2_SDA_PIN		7
 #define NSLU2_SCL_PIN		6

arch/arm/mach-kirkwood/irq.c

@@ -7,14 +7,13 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <mach/bridge-regs.h>
 #include <plat/irq.h>
-#include <asm/gpio.h>
 #include "common.h"
 
 static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)

arch/arm/mach-kirkwood/mpp.c

@@ -7,12 +7,11 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/mbus.h>
 #include <linux/io.h>
-#include <asm/gpio.h>
 #include <mach/hardware.h>
 #include <plat/mpp.h>
 #include "common.h"

arch/arm/mach-ks8695/Makefile

@@ -3,7 +3,7 @@
 # Makefile for KS8695 architecture support
 #
 
-obj-y				:= cpu.o irq.o time.o gpio.o devices.o
+obj-y				:= cpu.o irq.o time.o devices.o
 obj-m				:=
 obj-n				:=
 obj-				:=

arch/arm/mach-ks8695/board-acs5k.c

@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -34,7 +34,7 @@
 #include <asm/mach/irq.h>
 
 #include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
 
 #include "generic.h"
 

arch/arm/mach-ks8695/board-dsm320.c

@@ -10,7 +10,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -29,7 +29,7 @@
 #include <asm/mach/irq.h>
 
 #include <mach/devices.h>
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
 
 #include "generic.h"
 

arch/arm/mach-ks8695/board-micrel.c

@@ -5,7 +5,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/interrupt.h>
@@ -18,7 +18,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/gpio.h>
+#include <mach/gpio-ks8695.h>
 #include <mach/devices.h>
 
 #include "generic.h"

arch/arm/mach-ks8695/devices.c

@@ -20,6 +20,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 
 #include <mach/irqs.h>

arch/arm/mach-ks8695/include/mach/gpio-ks8695.h

@@ -0,0 +1,39 @@
+/*
+ * Copyright (C) 2006 Andrew Victor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_KS8659_GPIO_H
+#define __MACH_KS8659_GPIO_H
+
+#include <linux/kernel.h>
+
+#define KS8695_GPIO_0		0
+#define KS8695_GPIO_1		1
+#define KS8695_GPIO_2		2
+#define KS8695_GPIO_3		3
+#define KS8695_GPIO_4		4
+#define KS8695_GPIO_5		5
+#define KS8695_GPIO_6		6
+#define KS8695_GPIO_7		7
+#define KS8695_GPIO_8		8
+#define KS8695_GPIO_9		9
+#define KS8695_GPIO_10		10
+#define KS8695_GPIO_11		11
+#define KS8695_GPIO_12		12
+#define KS8695_GPIO_13		13
+#define KS8695_GPIO_14		14
+#define KS8695_GPIO_15		15
+
+/*
+ * Configure GPIO pin as external interrupt source.
+ */
+extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
+
+/* Register the GPIOs */
+extern void ks8695_register_gpios(void);
+
+#endif /* __MACH_KS8659_GPIO_H */

arch/arm/mach-ks8695/include/mach/gpio.h

@@ -11,47 +11,9 @@
 #ifndef __ASM_ARCH_GPIO_H_
 #define __ASM_ARCH_GPIO_H_
 
-#include <linux/kernel.h>
-
-#define KS8695_GPIO_0		0
-#define KS8695_GPIO_1		1
-#define KS8695_GPIO_2		2
-#define KS8695_GPIO_3		3
-#define KS8695_GPIO_4		4
-#define KS8695_GPIO_5		5
-#define KS8695_GPIO_6		6
-#define KS8695_GPIO_7		7
-#define KS8695_GPIO_8		8
-#define KS8695_GPIO_9		9
-#define KS8695_GPIO_10		10
-#define KS8695_GPIO_11		11
-#define KS8695_GPIO_12		12
-#define KS8695_GPIO_13		13
-#define KS8695_GPIO_14		14
-#define KS8695_GPIO_15		15
-
-/*
- * Configure GPIO pin as external interrupt source.
- */
-extern int ks8695_gpio_interrupt(unsigned int pin, unsigned int type);
-
 /*
  * Map IRQ number to GPIO line.
  */
 extern int irq_to_gpio(unsigned int irq);
 
-#include <asm-generic/gpio.h>
-
-/* If it turns out that we need to optimise GPIO access for the
- * Micrel's GPIOs, then these can be changed to check their argument
- * directly as static inlines. However for now it's probably not
- * worthwhile.
- */
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_to_irq __gpio_to_irq
-
-/* Register the GPIOs */
-extern void ks8695_register_gpios(void);
-
 #endif

arch/arm/mach-ks8695/leds.c

@@ -7,14 +7,14 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 
 #include <asm/leds.h>
 #include <mach/devices.h>
-#include <mach/gpio.h>
 
 
 static inline void ks8695_led_on(unsigned int led)

arch/arm/mach-lpc32xx/Makefile

@@ -3,6 +3,6 @@
 #
 
 obj-y	:= timer.o irq.o common.o serial.o clock.o
-obj-y	+= gpiolib.o pm.o suspend.o
+obj-y	+= pm.o suspend.o
 obj-y	+= phy3250.o
 

arch/arm/mach-lpc32xx/include/mach/gpio-lpc32xx.h

@@ -0,0 +1,50 @@
+/*
+ * Author: Kevin Wells <kevin.wells@nxp.com>
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MACH_GPIO_LPC32XX_H
+#define __MACH_GPIO_LPC32XX_H
+
+/*
+ * Note!
+ * Muxed GP pins need to be setup to the GP state in the board level
+ * code prior to using this driver.
+ * GPI pins : 28xP3 group
+ * GPO pins : 24xP3 group
+ * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
+ */
+
+#define LPC32XX_GPIO_P0_MAX 8
+#define LPC32XX_GPIO_P1_MAX 24
+#define LPC32XX_GPIO_P2_MAX 13
+#define LPC32XX_GPIO_P3_MAX 6
+#define LPC32XX_GPI_P3_MAX 28
+#define LPC32XX_GPO_P3_MAX 24
+
+#define LPC32XX_GPIO_P0_GRP 0
+#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
+#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
+#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
+#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
+#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
+
+/*
+ * A specific GPIO can be selected with this macro
+ * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
+ * See the LPC32x0 User's guide for GPIO group numbers
+ */
+#define LPC32XX_GPIO(x, y) ((x) + (y))
+
+#endif /* __MACH_GPIO_LPC32XX_H */

arch/arm/mach-lpc32xx/include/mach/gpio.h

@@ -1,74 +0,0 @@
-/*
- * arch/arm/mach-lpc32xx/include/mach/gpio.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
-
-#include <asm-generic/gpio.h>
-
-/*
- * Note!
- * Muxed GP pins need to be setup to the GP state in the board level
- * code prior to using this driver.
- * GPI pins : 28xP3 group
- * GPO pins : 24xP3 group
- * GPIO pins: 8xP0 group, 24xP1 group, 13xP2 group, 6xP3 group
- */
-
-#define LPC32XX_GPIO_P0_MAX 8
-#define LPC32XX_GPIO_P1_MAX 24
-#define LPC32XX_GPIO_P2_MAX 13
-#define LPC32XX_GPIO_P3_MAX 6
-#define LPC32XX_GPI_P3_MAX 28
-#define LPC32XX_GPO_P3_MAX 24
-
-#define LPC32XX_GPIO_P0_GRP 0
-#define LPC32XX_GPIO_P1_GRP (LPC32XX_GPIO_P0_GRP + LPC32XX_GPIO_P0_MAX)
-#define LPC32XX_GPIO_P2_GRP (LPC32XX_GPIO_P1_GRP + LPC32XX_GPIO_P1_MAX)
-#define LPC32XX_GPIO_P3_GRP (LPC32XX_GPIO_P2_GRP + LPC32XX_GPIO_P2_MAX)
-#define LPC32XX_GPI_P3_GRP (LPC32XX_GPIO_P3_GRP + LPC32XX_GPIO_P3_MAX)
-#define LPC32XX_GPO_P3_GRP (LPC32XX_GPI_P3_GRP + LPC32XX_GPI_P3_MAX)
-
-/*
- * A specific GPIO can be selected with this macro
- * ie, GPIO_05 can be selected with LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
- * See the LPC32x0 User's guide for GPIO group numbers
- */
-#define LPC32XX_GPIO(x, y) ((x) + (y))
-
-static inline int gpio_get_value(unsigned gpio)
-{
-	return __gpio_get_value(gpio);
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
-	__gpio_set_value(gpio, value);
-}
-
-static inline int gpio_cansleep(unsigned gpio)
-{
-	return __gpio_cansleep(gpio);
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
-	return __gpio_to_irq(gpio);
-}
-
-#endif

arch/arm/mach-lpc32xx/phy3250.c

@@ -37,6 +37,7 @@
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
+#include <mach/gpio-lpc32xx.h>
 #include "common.h"
 
 /*

arch/arm/mach-mmp/aspenite.c

@@ -8,7 +8,7 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  publishhed by the Free Software Foundation.
  */
-
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
@@ -17,13 +17,13 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
 #include <linux/interrupt.h>
+#include <linux/gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/addr-map.h>
 #include <mach/mfp-pxa168.h>
 #include <mach/pxa168.h>
-#include <mach/gpio.h>
 #include <video/pxa168fb.h>
 #include <linux/input.h>
 #include <plat/pxa27x_keypad.h>

arch/arm/mach-mmp/brownstone.c

@@ -14,7 +14,6 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/max8649.h>
 #include <linux/regulator/fixed.h>

arch/arm/mach-mmp/gplugd.c

@@ -9,11 +9,11 @@
  */
 
 #include <linux/init.h>
+#include <linux/gpio.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
-#include <mach/gpio.h>
 #include <mach/pxa168.h>
 #include <mach/mfp-pxa168.h>
 

arch/arm/mach-mmp/include/mach/gpio-pxa.h

@@ -0,0 +1,30 @@
+#ifndef __ASM_MACH_GPIO_PXA_H
+#define __ASM_MACH_GPIO_PXA_H
+
+#include <mach/addr-map.h>
+#include <mach/irqs.h>
+
+#define GPIO_REGS_VIRT	(APB_VIRT_BASE + 0x19000)
+
+#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
+#define GPIO_REG(x)	(*((volatile u32 *)(GPIO_REGS_VIRT + (x))))
+
+#define NR_BUILTIN_GPIO		IRQ_GPIO_NUM
+
+#define gpio_to_bank(gpio)	((gpio) >> 5)
+
+/* NOTE: these macros are defined here to make optimization of
+ * gpio_{get,set}_value() to work when 'gpio' is a constant.
+ * Usage of these macros otherwise is no longer recommended,
+ * use generic GPIO API whenever possible.
+ */
+#define GPIO_bit(gpio)	(1 << ((gpio) & 0x1f))
+
+#define GPLR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00)
+#define GPDR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c)
+#define GPSR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18)
+#define GPCR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24)
+
+#include <plat/gpio-pxa.h>
+
+#endif /* __ASM_MACH_GPIO_PXA_H */

arch/arm/mach-mmp/include/mach/gpio.h

@@ -1,36 +1,13 @@
 #ifndef __ASM_MACH_GPIO_H
 #define __ASM_MACH_GPIO_H
 
-#include <mach/addr-map.h>
-#include <mach/irqs.h>
 #include <asm-generic/gpio.h>
 
-#define GPIO_REGS_VIRT	(APB_VIRT_BASE + 0x19000)
-
-#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x)	(*((volatile u32 *)(GPIO_REGS_VIRT + (x))))
-
-#define NR_BUILTIN_GPIO		IRQ_GPIO_NUM
-
-#define gpio_to_bank(gpio)	((gpio) >> 5)
 #define gpio_to_irq(gpio)	(IRQ_GPIO_START + (gpio))
 #define irq_to_gpio(irq)	((irq) - IRQ_GPIO_START)
 
-
 #define __gpio_is_inverted(gpio)	(0)
 #define __gpio_is_occupied(gpio)	(0)
 
-/* NOTE: these macros are defined here to make optimization of
- * gpio_{get,set}_value() to work when 'gpio' is a constant.
- * Usage of these macros otherwise is no longer recommended,
- * use generic GPIO API whenever possible.
- */
-#define GPIO_bit(gpio)	(1 << ((gpio) & 0x1f))
-
-#define GPLR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00)
-#define GPDR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c)
-#define GPSR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18)
-#define GPCR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24)
-
 #include <plat/gpio.h>
 #endif /* __ASM_MACH_GPIO_H */