uboot-vybrid_public/include/configs/XPEDITE1K.h

/*
 * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * config for XPedite1000 from XES Inc.
 * Ported from EBONY config by Travis B. Sawyer <tsawyer@sandburst.com>
 * (C) Copyright 2003 Sandburst Corporation
 * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* High Level Configuration Options */
#define CONFIG_XPEDITE1K	1		/* Board is XPedite 1000 */
#define CONFIG_4xx		1		/* ... PPC4xx family */
#define CONFIG_440		1
#define CONFIG_440GX		1		/* 440 GX */
#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_pre_init	*/
#define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll */

/* POST support */
#define CONFIG_POST		(CONFIG_SYS_POST_RTC	| \
				 CONFIG_SYS_POST_I2C)

/*
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000		/* _must_ be 0 */
#define CONFIG_SYS_FLASH_BASE		0xff000000		/* start of FLASH */

#define CONFIG_SYS_MONITOR_BASE		TEXT_BASE		/* start of monitor */
#define CONFIG_SYS_PCI_MEMBASE		0x80000000		/* mapped pci memory */
#define CONFIG_SYS_PERIPHERAL_BASE	0xe0000000		/* internal peripherals */
#define CONFIG_SYS_ISRAM_BASE		0xc0000000		/* internal SRAM */
#define CONFIG_SYS_PCI_BASE		0xd0000000		/* internal PCI regs */

#define CONFIG_SYS_NVRAM_BASE_ADDR	(CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
#define CONFIG_SYS_GPIO_BASE		(CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)

#define USR_LED0	0x00000080
#define USR_LED1	0x00000100
#define USR_LED2	0x00000200
#define USR_LED3	0x00000400

#ifndef __ASSEMBLY__
extern unsigned long in32(unsigned int);
extern void out32(unsigned int, unsigned long);

#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0))
#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1))
#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2))
#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3))

#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0))
#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1))
#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2))
#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3))
#endif

/* Initial RAM & stack pointer (placed in internal SRAM) */
#define CONFIG_SYS_TEMP_STACK_OCM	1
#define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_ISRAM_BASE
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_ISRAM_BASE	/* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_END		0x2000	/* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_POST_WORD_ADDR

#define CONFIG_SYS_MONITOR_LEN	(256 * 1024)	/* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN	(128 * 1024)	/* Reserve 128 kB for malloc */

/* Serial Port */
#undef	CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_BAUDRATE		9600
#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400}

/* RTC: STMicro M41T00 */
#define CONFIG_RTC_M41T11		1
#define CONFIG_SYS_I2C_RTC_ADDR		0x68
#define CONFIG_SYS_M41T11_BASE_YEAR	2000

/*
 * FLASH related
 */
#define CONFIG_SYS_MAX_FLASH_BANKS	3
#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, 0xf0000000, 0xf4000000 }
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST		/* MirrorBit flashes are optional */

#undef	CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms) */

/* DDR SDRAM */
#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS	{0x54}	/* SPD i2c spd addresses */
#define CONFIG_VERY_BIG_RAM	1

/* I2C */
#define CONFIG_HARD_I2C			1	/* I2C with hardware support */
#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE		0x7f
#define CONFIG_SYS_I2C_NOPROBES	{0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69}

/*
 * Environment Configuration
 */
#define CONFIG_ENV_IS_IN_FLASH	1
#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128k (one sector) for env */
#define CONFIG_ENV_SIZE		0x8000
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))

/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10

#define CONFIG_BOOTARGS		"root=/dev/hda1 "
#define CONFIG_BOOTCOMMAND	"bootm ffc00000"	/* autoboot command */
#define CONFIG_BOOTDELAY	5			/* disable autoboot */
#define CONFIG_BAUDRATE		9600

#define CONFIG_LOADS_ECHO	1		/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII		1	/* MII PHY management */
#define CONFIG_PHY_ADDR		4	/* PHY address phy0 not populated */
#define CONFIG_PHY2_ADDR	4	/* PHY address phy2 */
#define CONFIG_PHY3_ADDR	8	/* PHY address phy3 */
#define CONFIG_NET_MULTI	1
#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET	1	/* reset phy upon startup */
#define CONFIG_SYS_RX_ETH_BUFFER 32	/* Number of ethernet rx buffers & descriptors */

#define CONFIG_HAS_ETH2		1	/* add support for "eth2addr" */
#define CONFIG_HAS_ETH3		1	/* add support for "eth3addr" */

/* BOOTP options */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_I2C
#define CONFIG_CMD_DATE
#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_PING
#define CONFIG_CMD_ELF
#define CONFIG_CMD_MII
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_FAT

#undef CONFIG_WATCHDOG			/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory */
#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM */

#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */

#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */

/*
 * PCI
 */
/* General PCI */
#define CONFIG_PCI				/* include pci support */
#define CONFIG_PCI_PNP				/* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW			/* show pci devices on startup */
#define CONFIG_SYS_PCI_TARGBASE	0x80000000	/* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */

/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT		/* let board init pci target */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014	/* IBM */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
#define CONFIG_SYS_PCI_FORCE_PCI_CONV		/* Force PCI Conventional Mode */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

/*
 * Internal Definitions
 */
#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM	0x02		/* Software reboot */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif
#endif	/* __CONFIG_H */