uboot-vybrid_public/board/korat/korat.c

/*
 * (C) Copyright 2007
 * Larry Johnson, lrj@acm.org
 *
 * (C) Copyright 2006
 * Stefan Roese, DENX Software Engineering, sr@denx.de.
 *
 * (C) Copyright 2006
 * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
 * Alain Saurel,	    AMCC/IBM, alain.saurel@fr.ibm.com
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

#include <common.h>
#include <asm/processor.h>
#include <asm-ppc/io.h>
#include <i2c.h>
#include <ppc440.h>

DECLARE_GLOBAL_DATA_PTR;

extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */

ulong flash_get_size(ulong base, int banknum);

int board_early_init_f(void)
{
	u32 sdr0_pfc1, sdr0_pfc2;
	u32 gpio0_ir;
	u32 reg;
	int eth;

	mtdcr(ebccfga, xbcfg);
	mtdcr(ebccfgd, 0xb8400000);

	/*--------------------------------------------------------------------
	 * Setup the GPIO pins
	 *
	 * Korat GPIO usage:
	 *
	 *                   Init.
	 * Pin    Source I/O value Function
	 * ------ ------ --- ----- ---------------------------------
	 * GPIO00  Alt1  I/O   x   PerAddr07
	 * GPIO01  Alt1  I/O   x   PerAddr06
	 * GPIO02  Alt1  I/O   x   PerAddr05
	 * GPIO03  GPIO   x    x   GPIO03 to expansion bus connector
	 * GPIO04  GPIO   x    x   GPIO04 to expansion bus connector
	 * GPIO05  GPIO   x    x   GPIO05 to expansion bus connector
	 * GPIO06  Alt1   O    x   PerCS1 (2nd NOR flash)
	 * GPIO07  Alt1   O    x   PerCS2 (CPLD)
	 * GPIO08  Alt1   O    x   PerCS3 to expansion bus connector
	 * GPIO09  Alt1   O    x   PerCS4 to expansion bus connector
	 * GPIO10  Alt1   O    x   PerCS5 to expansion bus connector
	 * GPIO11  Alt1   I    x   PerErr
	 * GPIO12  GPIO   O    0   ATMega !Reset
	 * GPIO13  GPIO   O    1   SPI Atmega !SS
	 * GPIO14  GPIO   O    1   Write protect EEPROM #1 (0xA8)
	 * GPIO15  GPIO   O    0   CPU Run LED !On
	 * GPIO16  Alt1   O    x   GMC1TxD0
	 * GPIO17  Alt1   O    x   GMC1TxD1
	 * GPIO18  Alt1   O    x   GMC1TxD2
	 * GPIO19  Alt1   O    x   GMC1TxD3
	 * GPIO20  Alt1   O    x   RejectPkt0
	 * GPIO21  Alt1   O    x   RejectPkt1
	 * GPIO22  GPIO   I    x   PGOOD_DDR
	 * GPIO23  Alt1   O    x   SCPD0
	 * GPIO24  Alt1   O    x   GMC0TxD2
	 * GPIO25  Alt1   O    x   GMC0TxD3
	 * GPIO26  GPIO? I/O   x   IIC0SDA (selected in SDR0_PFC4)
	 * GPIO27  GPIO   O    0   PHY #0 1000BASE-X
	 * GPIO28  GPIO   O    0   PHY #1 1000BASE-X
	 * GPIO29  GPIO   I    x   Test jumper !Present
	 * GPIO30  GPIO   I    x   SFP module #0 !Present
	 * GPIO31  GPIO   I    x   SFP module #1 !Present
	 *
	 * GPIO32  GPIO   O    1   SFP module #0 Tx !Enable
	 * GPIO33  GPIO   O    1   SFP module #1 Tx !Enable
	 * GPIO34  Alt2   I    x   !UART1_CTS
	 * GPIO35  Alt2   O    x   !UART1_RTS
	 * GPIO36  Alt1   I    x   !UART0_CTS
	 * GPIO37  Alt1   O    x   !UART0_RTS
	 * GPIO38  Alt2   O    x   UART1_Tx
	 * GPIO39  Alt2   I    x   UART1_Rx
	 * GPIO40  Alt1   I    x   IRQ0 (Ethernet 0)
	 * GPIO41  Alt1   I    x   IRQ1 (Ethernet 1)
	 * GPIO42  Alt1   I    x   IRQ2 (PCI interrupt)
	 * GPIO43  Alt1   I    x   IRQ3 (System Alert from CPLD)
	 * GPIO44  xxxx   x    x   (grounded through pulldown)
	 * GPIO45  GPIO   O    0   PHY #0 Enable
	 * GPIO46  GPIO   O    0   PHY #1 Enable
	 * GPIO47  GPIO   I    x   Reset switch !Pressed
	 * GPIO48  GPIO   I    x   Shutdown switch !Pressed
	 * GPIO49  xxxx   x    x   (reserved for trace port)
	 *   .      .     .    .               .
	 *   .      .     .    .               .
	 *   .      .     .    .               .
	 * GPIO63  xxxx   x    x   (reserved for trace port)
	 *-------------------------------------------------------------------*/

	out_be32((u32 *) GPIO0_OR, 0x00060000);
	out_be32((u32 *) GPIO1_OR, 0xC0000000);

	out_be32((u32 *) GPIO0_OSRL, 0x54055400);
	out_be32((u32 *) GPIO0_OSRH, 0x55015000);
	out_be32((u32 *) GPIO1_OSRL, 0x02180000);
	out_be32((u32 *) GPIO1_OSRH, 0x00000000);

	out_be32((u32 *) GPIO0_TSRL, 0x54055500);
	out_be32((u32 *) GPIO0_TSRH, 0x00015000);
	out_be32((u32 *) GPIO1_TSRL, 0x00000000);
	out_be32((u32 *) GPIO1_TSRH, 0x00000000);

	out_be32((u32 *) GPIO0_TCR, 0x000FF0D8);
	out_be32((u32 *) GPIO1_TCR, 0xD6060000);

	out_be32((u32 *) GPIO0_ISR1L, 0x54000100);
	out_be32((u32 *) GPIO0_ISR1H, 0x00500000);
	out_be32((u32 *) GPIO1_ISR1L, 0x00405500);
	out_be32((u32 *) GPIO1_ISR1H, 0x00000000);

	out_be32((u32 *) GPIO0_ISR2L, 0x00000000);
	out_be32((u32 *) GPIO0_ISR2H, 0x00000000);
	out_be32((u32 *) GPIO1_ISR2L, 0x04010000);
	out_be32((u32 *) GPIO1_ISR2H, 0x00000000);

	out_be32((u32 *) GPIO0_ISR3L, 0x00000000);
	out_be32((u32 *) GPIO0_ISR3H, 0x00000000);
	out_be32((u32 *) GPIO1_ISR3L, 0x00000000);
	out_be32((u32 *) GPIO1_ISR3H, 0x00000000);

	/*--------------------------------------------------------------------
	 * Setup the interrupt controller polarities, triggers, etc.
	 *-------------------------------------------------------------------*/
	mtdcr(uic0sr, 0xffffffff);	/* clear all */
	mtdcr(uic0er, 0x00000000);	/* disable all */
	mtdcr(uic0cr, 0x00000005);	/* ATI & UIC1 crit are critical */
	mtdcr(uic0pr, 0xfffff7ff);	/* per ref-board manual */
	mtdcr(uic0tr, 0x00000000);	/* per ref-board manual */
	mtdcr(uic0vr, 0x00000000);	/* int31 highest, base=0x000 */
	mtdcr(uic0sr, 0xffffffff);	/* clear all */

	mtdcr(uic1sr, 0xffffffff);	/* clear all */
	mtdcr(uic1er, 0x00000000);	/* disable all */
	mtdcr(uic1cr, 0x00000000);	/* all non-critical */
	mtdcr(uic1pr, 0xffffffff);	/* per ref-board manual */
	mtdcr(uic1tr, 0x00000000);	/* per ref-board manual */
	mtdcr(uic1vr, 0x00000000);	/* int31 highest, base=0x000 */
	mtdcr(uic1sr, 0xffffffff);	/* clear all */

	mtdcr(uic2sr, 0xffffffff);	/* clear all */
	mtdcr(uic2er, 0x00000000);	/* disable all */
	mtdcr(uic2cr, 0x00000000);	/* all non-critical */
	mtdcr(uic2pr, 0xffffffff);	/* per ref-board manual */
	mtdcr(uic2tr, 0x00000000);	/* per ref-board manual */
	mtdcr(uic2vr, 0x00000000);	/* int31 highest, base=0x000 */
	mtdcr(uic2sr, 0xffffffff);	/* clear all */

	/* take sim card reader and CF controller out of reset */
	out_8((u8 *) CFG_CPLD_BASE + 0x04, 0x80);

	/* Configure the two Ethernet PHYs.  For each PHY, configure for fiber
	 * if the SFP module is present, and for copper if it is not present.
	 */
	gpio0_ir = in_be32((u32 *) GPIO0_IR);
	for (eth = 0; eth < 2; ++eth) {
		if (gpio0_ir & (0x00000001 << (1 - eth))) {
			/* SFP module not present: configure PHY for copper. */
			/* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */
			out_8((u8 *) CFG_CPLD_BASE + 0x06,
			      in_8((u8 *) CFG_CPLD_BASE + 0x06) |
			      0x06 << (4 * eth));
		} else {
			/* SFP module present: configure PHY for fiber and
			   enable output */
			out_be32((u32 *) GPIO0_OR, in_be32((u32 *) GPIO0_OR) |
				 (0x00000001 << (4 - eth)));
			out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) &
				 ~(0x00000001 << (31 - eth)));
		}
	}
	/* enable Ethernet: set GPIO45 and GPIO46 to 1 */
	out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) | 0x00060000);

	/* select Ethernet pins */
	mfsdr(SDR0_PFC1, sdr0_pfc1);
	sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
	    SDR0_PFC1_SELECT_CONFIG_4;
	mfsdr(SDR0_PFC2, sdr0_pfc2);
	sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
	    SDR0_PFC2_SELECT_CONFIG_4;
	mtsdr(SDR0_PFC2, sdr0_pfc2);
	mtsdr(SDR0_PFC1, sdr0_pfc1);

	/* PCI arbiter enabled */
	mfsdr(sdr_pci0, reg);
	mtsdr(sdr_pci0, 0x80000000 | reg);

	return 0;
}

static int man_data_read(unsigned int addr)
{
	/*
	 * Read an octet of data from address "addr" in the manufacturer's
	 * information serial EEPROM, or -1 on error.
	 */
	u8 data[2];

	if (0 != i2c_probe(MAN_DATA_EEPROM_ADDR) ||
	    0 != i2c_read(MAN_DATA_EEPROM_ADDR, addr, 1, data, 1)) {
		debug("man_data_read(0x%02X) failed\n", addr);
		return -1;
	}
	debug("man_info_read(0x%02X) returned 0x%02X\n", addr, data[0]);
	return data[0];
}

static unsigned int man_data_field_addr(unsigned int const field)
{
	/*
	 * The manufacturer's information serial EEPROM contains a sequence of
	 * zero-delimited fields.  Return the starting address of field "field",
	 * or 0 on error.
	 */
	unsigned addr, i;

	if (0 == field || 'A' != man_data_read(0) || '\0' != man_data_read(1))
		/* Only format "A" is currently supported */
		return 0;

	for (addr = 2, i = 1; i < field && addr < 256; ++addr) {
		if ('\0' == man_data_read(addr))
			++i;
	}
	return (addr < 256) ? addr : 0;
}

static char *man_data_read_field(char s[], unsigned const field,
				 unsigned const length)
{
	/*
	 * Place the null-terminated contents of field "field" of length
	 * "length" from the manufacturer's information serial EEPROM into
	 * string "s[length + 1]" and return a pointer to s, or return 0 on
	 * error. In either case the original contents of s[] is not preserved.
	 */
	unsigned addr, i;

	addr = man_data_field_addr(field);
	if (0 == addr || addr + length >= 255)
		return 0;

	for (i = 0; i < length; ++i) {
		int const c = man_data_read(addr++);

		if (c <= 0)
			return 0;

		s[i] = (char)c;
	}
	if (0 != man_data_read(addr))
		return 0;

	s[i] = '\0';
	return s;
}

static void set_serial_number(void)
{
	/*
	 * If the environmental variable "serial#" is not set, try to set it
	 * from the manufacturer's information serial EEPROM.
	 */
	char s[MAN_SERIAL_NO_LENGTH + 1];

	if (0 == getenv("serial#") &&
	    0 != man_data_read_field(s, MAN_SERIAL_NO_FIELD,
				     MAN_SERIAL_NO_LENGTH))
		setenv("serial#", s);
}

static void set_mac_addresses(void)
{
	/*
	 * If the environmental variables "ethaddr" and/or "eth1addr" are not
	 * set, try to set them from the manufacturer's information serial
	 * EEPROM.
	 */
	char s[MAN_MAC_ADDR_LENGTH + 1];

	if (0 != getenv("ethaddr") && 0 != getenv("eth1addr"))
		return;

	if (0 == man_data_read_field(s, MAN_MAC_ADDR_FIELD,
				     MAN_MAC_ADDR_LENGTH))
		return;

	if (0 == getenv("ethaddr"))
		setenv("ethaddr", s);

	if (0 == getenv("eth1addr")) {
		++s[MAN_MAC_ADDR_LENGTH - 1];
		setenv("eth1addr", s);
	}
}

/*---------------------------------------------------------------------------+
  | misc_init_r.
  +---------------------------------------------------------------------------*/
int misc_init_r(void)
{
	uint pbcr;
	int size_val = 0;
	u32 reg;
	unsigned long usb2d0cr = 0;
	unsigned long usb2phy0cr, usb2h0cr = 0;
	unsigned long sdr0_pfc1;
	char *act = getenv("usbact");

	/*
	 * FLASH stuff...
	 */

	/* Re-do sizing to get full correct info */

	/* adjust flash start and offset */
	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
	gd->bd->bi_flashoffset = 0;

	mtdcr(ebccfga, pb0cr);
	pbcr = mfdcr(ebccfgd);
	switch (gd->bd->bi_flashsize) {
	case 1 << 20:
		size_val = 0;
		break;
	case 2 << 20:
		size_val = 1;
		break;
	case 4 << 20:
		size_val = 2;
		break;
	case 8 << 20:
		size_val = 3;
		break;
	case 16 << 20:
		size_val = 4;
		break;
	case 32 << 20:
		size_val = 5;
		break;
	case 64 << 20:
		size_val = 6;
		break;
	case 128 << 20:
		size_val = 7;
		break;
	}
	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
	mtdcr(ebccfga, pb0cr);
	mtdcr(ebccfgd, pbcr);

	/*
	 * Re-check to get correct base address
	 */
	flash_get_size(gd->bd->bi_flashstart, 0);

	/* Monitor protection ON by default */
	(void)flash_protect(FLAG_PROTECT_SET, -CFG_MONITOR_LEN, 0xffffffff,
			    &flash_info[0]);

	/* Env protection ON by default */
	(void)flash_protect(FLAG_PROTECT_SET,
			    CFG_ENV_ADDR_REDUND,
			    CFG_ENV_ADDR_REDUND + 2 * CFG_ENV_SECT_SIZE - 1,
			    &flash_info[0]);

	/*
	 * USB suff...
	 */
	if (act == NULL || strcmp(act, "hostdev") == 0) {
		/* SDR Setting */
		mfsdr(SDR0_PFC1, sdr0_pfc1);
		mfsdr(SDR0_USB2D0CR, usb2d0cr);
		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mfsdr(SDR0_USB2H0CR, usb2h0cr);

		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_WDINT_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;	/*1 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;	/*0 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;	/*1 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;	/*1 */

		/* An 8-bit/60MHz interface is the only possible alternative
		   when connecting the Device to the PHY */
		usb2h0cr = usb2h0cr & ~SDR0_USB2H0CR_WDINT_MASK;
		usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;	/*1 */

		/* To enable the USB 2.0 Device function through the UTMI interface */
		usb2d0cr = usb2d0cr & ~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION;	/*1 */

		sdr0_pfc1 = sdr0_pfc1 & ~SDR0_PFC1_UES_MASK;
		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL;	/*0 */

		mtsdr(SDR0_PFC1, sdr0_pfc1);
		mtsdr(SDR0_USB2D0CR, usb2d0cr);
		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mtsdr(SDR0_USB2H0CR, usb2h0cr);

		/*clear resets */
		udelay(1000);
		mtsdr(SDR0_SRST1, 0x00000000);
		udelay(1000);
		mtsdr(SDR0_SRST0, 0x00000000);

		printf("USB:   Host(int phy) Device(ext phy)\n");

	} else if (strcmp(act, "dev") == 0) {
		/*-------------------PATCH-------------------------------*/
		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);

		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;	/*0 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;	/*1 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;	/*1 */
		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);

		udelay(1000);
		mtsdr(SDR0_SRST1, 0x672c6000);

		udelay(1000);
		mtsdr(SDR0_SRST0, 0x00000080);

		udelay(1000);
		mtsdr(SDR0_SRST1, 0x60206000);

		*(unsigned int *)(0xe0000350) = 0x00000001;

		udelay(1000);
		mtsdr(SDR0_SRST1, 0x60306000);
		/*-------------------PATCH-------------------------------*/

		/* SDR Setting */
		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mfsdr(SDR0_USB2H0CR, usb2h0cr);
		mfsdr(SDR0_USB2D0CR, usb2d0cr);
		mfsdr(SDR0_PFC1, sdr0_pfc1);

		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_WDINT_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ;	/*0 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN;	/*1 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV;	/*0 */
		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK;
		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV;	/*0 */

		usb2h0cr = usb2h0cr & ~SDR0_USB2H0CR_WDINT_MASK;
		usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ;	/*0 */

		usb2d0cr = usb2d0cr & ~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_EBC_SELECTION;	/*0 */

		sdr0_pfc1 = sdr0_pfc1 & ~SDR0_PFC1_UES_MASK;
		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL;	/*1 */

		mtsdr(SDR0_USB2H0CR, usb2h0cr);
		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
		mtsdr(SDR0_USB2D0CR, usb2d0cr);
		mtsdr(SDR0_PFC1, sdr0_pfc1);

		/*clear resets */
		udelay(1000);
		mtsdr(SDR0_SRST1, 0x00000000);
		udelay(1000);
		mtsdr(SDR0_SRST0, 0x00000000);

		printf("USB:   Device(int phy)\n");
	}

	mfsdr(SDR0_SRST1, reg);	/* enable security/kasumi engines */
	reg &= ~(SDR0_SRST1_CRYP0 | SDR0_SRST1_KASU0);
	mtsdr(SDR0_SRST1, reg);

	/*
	 * Clear PLB4A0_ACR[WRP]
	 * This fix will make the MAL burst disabling patch for the Linux
	 * EMAC driver obsolete.
	 */
	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
	mtdcr(plb4_acr, reg);

	set_serial_number();
	set_mac_addresses();
	return 0;
}

int checkboard(void)
{
	char const *const s = getenv("serial#");
	u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0);
	u32 const gpio0_or = in_be32((u32 *) GPIO0_OR);

	printf("Board: Korat, Rev. %X", rev);
	if (s != NULL)
		printf(", serial# %s", s);

	printf(", Ethernet PHY 0: ");
	if (gpio0_or & 0x00000010)
		printf("fiber");
	else
		printf("copper");

	printf(", PHY 1: ");
	if (gpio0_or & 0x00000008)
		printf("fiber");
	else
		printf("copper");

	printf(".\n");
	return (0);
}

#if defined(CFG_DRAM_TEST)
int testdram(void)
{
	unsigned long *mem = (unsigned long *)0;
	const unsigned long kend = (1024 / sizeof(unsigned long));
	unsigned long k, n;

	mtmsr(0);

	/* TODO: find correct size of SDRAM */
	for (k = 0; k < CFG_MBYTES_SDRAM;
	     ++k, mem += (1024 / sizeof(unsigned long))) {
		if ((k & 1023) == 0)
			printf("%3d MB\r", k / 1024);

		memset(mem, 0xaaaaaaaa, 1024);
		for (n = 0; n < kend; ++n) {
			if (mem[n] != 0xaaaaaaaa) {
				printf("SDRAM test fails at: %08x\n",
				       (uint) & mem[n]);
				return 1;
			}
		}

		memset(mem, 0x55555555, 1024);
		for (n = 0; n < kend; ++n) {
			if (mem[n] != 0x55555555) {
				printf("SDRAM test fails at: %08x\n",
				       (uint) & mem[n]);
				return 1;
			}
		}
	}
	printf("SDRAM test passes\n");
	return 0;
}
#endif /* defined(CFG_DRAM_TEST) */

/*************************************************************************
 *  pci_pre_init
 *
 *  This routine is called just prior to registering the hose and gives
 *  the board the opportunity to check things. Returning a value of zero
 *  indicates that things are bad & PCI initialization should be aborted.
 *
 *	Different boards may wish to customize the pci controller structure
 *	(add regions, override default access routines, etc) or perform
 *	certain pre-initialization actions.
 *
 ************************************************************************/
#if defined(CONFIG_PCI)
int pci_pre_init(struct pci_controller *hose)
{
	unsigned long addr;

	/*-------------------------------------------------------------------------+
	  | Set priority for all PLB3 devices to 0.
	  | Set PLB3 arbiter to fair mode.
	  +-------------------------------------------------------------------------*/
	mfsdr(sdr_amp1, addr);
	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
	addr = mfdcr(plb3_acr);
	mtdcr(plb3_acr, addr | 0x80000000);

	/*-------------------------------------------------------------------------+
	  | Set priority for all PLB4 devices to 0.
	  +-------------------------------------------------------------------------*/
	mfsdr(sdr_amp0, addr);
	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
	mtdcr(plb4_acr, addr);

	/*-------------------------------------------------------------------------+
	  | Set Nebula PLB4 arbiter to fair mode.
	  +-------------------------------------------------------------------------*/
	/* Segment0 */
	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
	mtdcr(plb0_acr, addr);

	/* Segment1 */
	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
	mtdcr(plb1_acr, addr);

	return 1;
}
#endif /* defined(CONFIG_PCI) */

/*************************************************************************
 *  pci_target_init
 *
 *	The bootstrap configuration provides default settings for the pci
 *	inbound map (PIM). But the bootstrap config choices are limited and
 *	may not be sufficient for a given board.
 *
 ************************************************************************/
#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
	/*--------------------------------------------------------------------------+
	 * Set up Direct MMIO registers
	 *--------------------------------------------------------------------------*/
	/*--------------------------------------------------------------------------+
	  | PowerPC440EPX PCI Master configuration.
	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
	  |   Use byte reversed out routines to handle endianess.
	  | Make this region non-prefetchable.
	  +--------------------------------------------------------------------------*/
	out32r(PCIX0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
	out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE);	/* PMM0 PCI Low Address */
	out32r(PCIX0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
	out32r(PCIX0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */

	out32r(PCIX0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
	out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2);	/* PMM0 Local Address */
	out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
	out32r(PCIX0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
	out32r(PCIX0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */

	out32r(PCIX0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
	out32r(PCIX0_PTM1LA, 0);	/* Local Addr. Reg */
	out32r(PCIX0_PTM2MS, 0);	/* Memory Size/Attribute */
	out32r(PCIX0_PTM2LA, 0);	/* Local Addr. Reg */

	/*--------------------------------------------------------------------------+
	 * Set up Configuration registers
	 *--------------------------------------------------------------------------*/

	/* Program the board's subsystem id/vendor id */
	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
			      CFG_PCI_SUBSYS_VENDORID);
	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);

	/* Configure command register as bus master */
	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);

	/* 240nS PCI clock */
	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);

	/* No error reporting */
	pci_write_config_word(0, PCI_ERREN, 0);

	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);

	/*--------------------------------------------------------------------------+
	 * Set up Configuration registers for on-board NEC uPD720101 USB controller
	 *--------------------------------------------------------------------------*/
	pci_write_config_dword(PCI_BDF(0x0, 0xC, 0x0), 0xE4, 0x00000020);
}
#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */

/*************************************************************************
 *  pci_master_init
 *
 ************************************************************************/
#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
	unsigned short temp_short;

	/*--------------------------------------------------------------------------+
	  | Write the PowerPC440 EP PCI Configuration regs.
	  |   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
	  |   Enable PowerPC440 EP to act as a PCI memory target (PTM).
	  +--------------------------------------------------------------------------*/
	pci_read_config_word(0, PCI_COMMAND, &temp_short);
	pci_write_config_word(0, PCI_COMMAND,
			      temp_short | PCI_COMMAND_MASTER |
			      PCI_COMMAND_MEMORY);
}
#endif

/*************************************************************************
 *  is_pci_host
 *
 *	This routine is called to determine if a pci scan should be
 *	performed. With various hardware environments (especially cPCI and
 *	PPMC) it's insufficient to depend on the state of the arbiter enable
 *	bit in the strap register, or generic host/adapter assumptions.
 *
 *	Rather than hard-code a bad assumption in the general 440 code, the
 *	440 pci code requires the board to decide at runtime.
 *
 *	Return 0 for adapter mode, non-zero for host (monarch) mode.
 *
 *
 ************************************************************************/
#if defined(CONFIG_PCI)
int is_pci_host(struct pci_controller *hose)
{
	/* Korat is always configured as host. */
	return (1);
}
#endif

#if defined(CONFIG_POST)
/*
 * Returns 1 if keys pressed to start the power-on long-running tests
 * Called from board_init_f().
 */
int post_hotkeys_pressed(void)
{
	return 0;		/* No hotkeys supported */
}
#endif