uboot-vybrid_public/include/configs/kmeter1.h

/*
 * Copyright (C) 2006 Freescale Semiconductor, Inc.
 *                    Dave Liu <daveliu@freescale.com>
 *
 * Copyright (C) 2007 Logic Product Development, Inc.
 *                    Peter Barada <peterb@logicpd.com>
 *
 * Copyright (C) 2007 MontaVista Software, Inc.
 *                    Anton Vorontsov <avorontsov@ru.mvista.com>
 *
 * (C) Copyright 2008
 * Heiko Schocher, DENX Software Engineering, hs@denx.de.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300		1 /* E300 family */
#define CONFIG_QE		1 /* Has QE */
#define CONFIG_MPC83XX		1 /* MPC83XX family */
#define CONFIG_MPC8360		1 /* MPC8360 CPU specific */
#define CONFIG_KMETER1		1 /* KMETER1 board specific */

/*
 * System Clock Setup
 */
#define CONFIG_83XX_CLKIN		66000000
#define CONFIG_SYS_CLK_FREQ		66000000
#define CONFIG_83XX_PCICLK		66000000

/*
 * Hardware Reset Configuration Word
 */
#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_CSB_TO_CLKIN_4X1 | \
	HRCWL_CORE_TO_CSB_2X1 | \
	HRCWL_CE_PLL_VCO_DIV_2 | \
	HRCWL_CE_TO_PLL_1X6 )

#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_CORE_ENABLE | \
	HRCWH_FROM_0X00000100 | \
	HRCWH_BOOTSEQ_NORMAL | \
	HRCWH_SW_WATCHDOG_DISABLE | \
	HRCWH_ROM_LOC_LOCAL_16BIT | \
	HRCWH_BIG_ENDIAN | \
	HRCWH_LDP_CLEAR )

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRH		0x00000006
#define CONFIG_SYS_SICRL		0x00000000

#define CONFIG_BOARD_EARLY_INIT_R

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR		0xE0000000

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

#define CFG_83XX_DDR_USES_CS0

#undef CONFIG_DDR_ECC

/*
 * DDRCDR - DDR Control Driver Register
 */

#undef CONFIG_SPD_EEPROM	/* Do not use SPD EEPROM for DDR setup */

/*
 * Manually set up DDR parameters
 */
#define CONFIG_DDR_II
#define CONFIG_SYS_DDR_SIZE		256 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS		0x0000000f
#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
					 CSCONFIG_ROW_BIT_13 | \
					 CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS)

#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
					 SDRAM_CFG_SREN)
#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
#define CONFIG_SYS_DDR_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#define CONFIG_SYS_DDR_INTERVAL	((0x100 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
				 (0x406 << SDRAM_INTERVAL_REFINT_SHIFT))

#define CONFIG_SYS_DDR_MODE		0x04440242
#define CONFIG_SYS_DDR_MODE2		0x00800000

#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
				 (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
				 (0 << TIMING_CFG0_WWT_SHIFT) | \
				 (0 << TIMING_CFG0_RRT_SHIFT) | \
				 (0 << TIMING_CFG0_WRT_SHIFT) | \
				 (0 << TIMING_CFG0_RWT_SHIFT))

#define CONFIG_SYS_DDR_TIMING_1	((      TIMING_CFG1_CASLAT_40) | \
				 ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \
				 ( 1 << TIMING_CFG1_ACTTOACT_SHIFT) | \
				 ( 2 << TIMING_CFG1_WRREC_SHIFT) | \
				 ( 2 << TIMING_CFG1_REFREC_SHIFT) | \
				 ( 2 << TIMING_CFG1_ACTTORW_SHIFT) | \
				 ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
				 ( 2 << TIMING_CFG1_PRETOACT_SHIFT))

#define CONFIG_SYS_DDR_TIMING_2	((5 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
				 (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
				 (4 << TIMING_CFG2_CPO_SHIFT))

#define CONFIG_SYS_DDR_TIMING_3	0x00000000

/*
 * Memory test
 */
#define CONFIG_SYS_ALT_MEMTEST		/* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START	0x00100000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END		0x00F00000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE /* start of monitor */
#define CONFIG_SYS_FLASH_BASE		0xF0000000
#define CONFIG_SYS_FLASH_BASE_1		0xF2000000
#define CONFIG_SYS_PIGGY_BASE		0x80000000
#define CONFIG_SYS_PAXE_BASE		0xA0000000
#define	CONFIG_SYS_PAXE_SIZE		256

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef	CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN		(128 * 1024) /* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_END	0x1000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_SIZE	0x100 /* num bytes initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR		(LCRR_DBYP | LCRR_EADC_2 | LCRR_CLKDIV_4)

/*
 * Init Local Bus Memory Controller:
 *
 * Bank Bus     Machine PortSz  Size  Device
 * ---- ---     ------- ------  -----  ------
 *  0   Local   GPCM    16 bit  256MB FLASH
 *  1   Local   GPCM     8 bit  256KB GPIO/PIGGY
 *  3   Local   GPCM     8 bit  256MB PAXE
 *
 */
/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
#define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
#define CONFIG_SYS_FLASH_PROTECTION	1
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1

#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE /* Window base at flash base */
#define CONFIG_SYS_LBLAWAR0_PRELIM	0x8000001b /* 256MB window size */

#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | \
				(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
				BR_V)

#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
				OR_GPCM_SCY_5 | \
				OR_GPCM_TRLX | OR_GPCM_EAD)

#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max num of flash banks	*/
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sects on one chip */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_1 }

#undef	CONFIG_SYS_FLASH_CHECKSUM

/*
 * PRIO1/PIGGY on the local bus CS1
 */
#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_PIGGY_BASE /* Window base at flash base */
#define CONFIG_SYS_LBLAWAR1_PRELIM	0x80000011 /* 256KB window size */

#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_PIGGY_BASE | \
				(1 << BR_PS_SHIFT) | /* 8 bit port size */ \
				BR_V)
#define CONFIG_SYS_OR1_PRELIM		(0xfffc0000 | /* 256KB */ \
				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
				OR_GPCM_SCY_2 | \
				OR_GPCM_TRLX | OR_GPCM_EAD)

/*
 * PAXE on the local bus CS3
 */
#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_PAXE_BASE /* Window base at flash base */
#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000001b /* 256MB window size */

#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_PAXE_BASE | \
				(1 << BR_PS_SHIFT) | /* 8 bit port size */ \
				BR_V)
#define CONFIG_SYS_OR3_PRELIM	(MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \
				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
				OR_GPCM_SCY_2 | \
				OR_GPCM_TRLX | OR_GPCM_EAD)

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX	1
#undef	CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200,}

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)

/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT	1
#define CONFIG_OF_BOARD_SETUP	1
#define CONFIG_OF_STDOUT_VIA_ALIAS

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#undef CONFIG_PCI		/* No PCI */

#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI	1
#endif

/*
 * QE UEC ethernet configuration
 */
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME		"FSL UEC0"

#define CONFIG_UEC_ETH1		/* GETH1 */
#define UEC_VERBOSE_DEBUG	1

#ifdef CONFIG_UEC_ETH1
#define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE	/* not used in RMII Mode */
#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR	0
#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII
#endif

/*
 * Environment
 */

#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH	1
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE		0x20000
#define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

#else /* CFG_RAMBOOT */
#define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE		0x2000
#endif /* CFG_RAMBOOT */

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

/*
 * How to get access to the slot ID.  Put this here to make it easy
 * to modify in a centralized location.  This is used in the HDLC
 * driver to set the MAC.
*/
#define CONFIG_SYS_SLOT_ID_BASE		CONFIG_SYS_PIGGY_BASE
#define CONFIG_SYS_SLOT_ID_OFF		(0x07)	/* register offset */
#define CONFIG_SYS_SLOT_ID_MASK		(0x3f)	/* mask for slot ID bits */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NFS
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING

#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif

#if defined(CFG_RAMBOOT)
#undef CONFIG_CMD_ENV
#undef CONFIG_CMD_LOADS
#endif

#undef CONFIG_WATCHDOG		/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
#define CONFIG_SYS_LOAD_ADDR		0x200000 /* default load address */
#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt   */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
#else
#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
#define CONFIG_CMDLINE_EDITING	1	/* add command line history */

#define CONFIG_SYS_HZ			1000

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT		0x000000000
#define CONFIG_SYS_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
#define CONFIG_SYS_HID2			HID2_HBE

/*
 * MMU Setup
 */

#define CONFIG_HIGH_BATS	1	/* High BATs supported */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U

/* IMMRBAR & PCI IO: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U

/* PRIO1, PIGGY:  icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PIGGY_BASE | BATU_BL_256K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U

/* PAXE:  icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PAXE_BASE | BATU_BL_256K | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L	(CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \
				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U

#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
#define CFG_IBAT6L	(CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT6U	(CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_DBAT6L	CFG_IBAT6L
#define CFG_DBAT6U	CFG_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CFG_IBAT7L	(CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
			 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_IBAT7U	(CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_DBAT7L	CFG_IBAT7L
#define CFG_DBAT7U	CFG_IBAT7U
#else /* CONFIG_PCI */
#define CONFIG_SYS_IBAT6L	(0)
#define CONFIG_SYS_IBAT6U	(0)
#define CONFIG_SYS_IBAT7L	(0)
#define CONFIG_SYS_IBAT7U	(0)
#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
#endif /* CONFIG_PCI */

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD	0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM	0x02 /* Software reboot */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
#endif

#define CONFIG_BAUDRATE 115200

#define	CONFIG_BOOTDELAY	5	/* -1 disables auto-boot */
#undef	CONFIG_BOOTARGS			/* the boot command will set bootargs */

#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0"							\
	"rootpath=/opt/eldk/ppc_82xx\0"					\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"addtty=setenv bootargs ${bootargs}"				\
		" console=ttyS0,${baudrate}\0"				\
	"fdt_addr=f0080000\0"						\
	"kernel_addr=f00a0000\0"					\
	"ramdisk_addr=f03a0000\0"					\
	"kernel_addr_r=400000\0"					\
	"fdt_addr_r=800000\0"						\
	"ramdisk_addr_r=810000\0"					\
	"flash_self=run ramargs addip addtty;"				\
		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
	"flash_nfs=run nfsargs addip addtty;"				\
		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
	"net_nfs=tftp ${kernel_addr_r} ${boot_file}; "			\
		"tftp ${fdt_addr_r} ${fdt_file}; "			\
		"run nfsargs addip addtty;"				\
		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
	"fdt_file=/tftpboot/kmeter1/kmeter1.dtb\0"			\
	"boot_file=/tftpboot/kmeter1/uImage\0"				\
	"ramdisk_file=/tftpboot/kmeter1/uRamdisk\0"			\
	"u-boot=/tftpboot/kmeter1/u-boot.bin\0"				\
	"loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0"			\
	"load=tftp $loadaddr ${u-boot}\0"				\
	"update=protect off " MK_STR(TEXT_BASE) " +$filesize;"		\
		"erase " MK_STR(TEXT_BASE) " +$filesize;"		\
		"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;"	\
		"protect on " MK_STR(TEXT_BASE) " +$filesize;"		\
		"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;"	\
		"setenv filesize;saveenv\0"				\
	"upd=run load update\0"						\
	"loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0"		\
	"loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0"			\
	"loadkernel=tftp ${kernel_addr_r} ${boot_file}\0"		\
	"unlock=yes\0"							\
   ""

#define CONFIG_BOOTCOMMAND "run net_nfs"

#endif /* __CONFIG_H */