davinci_nand: cleanup I (minor)

Minor cleanup for DaVinci NAND code:

 - Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
   be defined when there are multiple chipselect lines in use
   (as with common 2 GByte chips).

 - Cleanup handling of EMIF control registers
    * Only need one pointer pointing to them
    * Remove incorrect and unused struct supersetting them

 - Use the standard waitfunc; we don't need a custom version

 - Partial legacy cleanup:
    * Don't initialize every board like it's a DM6446 EVM
    * #ifdef a bit more code for BROKEN_ECC

Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>

drivers/mtd/nand/davinci_nand.c

@@ -49,6 +49,8 @@
 
 extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
 
+static emif_registers *const emif_regs = (void *) DAVINCI_ASYNC_EMIF_CNTRL_BASE;
+
 static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 {
 	struct		nand_chip *this = mtd->priv;
@@ -115,34 +117,31 @@ static struct nand_ecclayout davinci_nand_ecclayout = {
 
 static void nand_davinci_enable_hwecc(struct mtd_info *mtd, int mode)
 {
-	emifregs	emif_addr;
 	int		dummy;
 
-	emif_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
-
-	dummy = emif_addr->NANDF1ECC;
-	dummy = emif_addr->NANDF2ECC;
-	dummy = emif_addr->NANDF3ECC;
-	dummy = emif_addr->NANDF4ECC;
+	dummy = emif_regs->NANDF1ECC;
+#ifdef CONFIG_SYS_DAVINCI_BROKEN_ECC
+	dummy = emif_regs->NANDF2ECC;
+	dummy = emif_regs->NANDF3ECC;
+	dummy = emif_regs->NANDF4ECC;
+#endif
 
-	emif_addr->NANDFCR |= (1 << 8);
+	/* FIXME:  only chipselect 0 is supported for now */
+	emif_regs->NANDFCR |= 1 << 8;
 }
 
 static u_int32_t nand_davinci_readecc(struct mtd_info *mtd, u_int32_t region)
 {
 	u_int32_t	ecc = 0;
-	emifregs	emif_base_addr;
-
-	emif_base_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
 
 	if (region == 1)
-		ecc = emif_base_addr->NANDF1ECC;
+		ecc = emif_regs->NANDF1ECC;
 	else if (region == 2)
-		ecc = emif_base_addr->NANDF2ECC;
+		ecc = emif_regs->NANDF2ECC;
 	else if (region == 3)
-		ecc = emif_base_addr->NANDF3ECC;
+		ecc = emif_regs->NANDF3ECC;
 	else if (region == 4)
-		ecc = emif_base_addr->NANDF4ECC;
+		ecc = emif_regs->NANDF4ECC;
 
 	return(ecc);
 }
@@ -369,24 +368,18 @@ static int nand_davinci_correct_data(struct mtd_info *mtd, u_char *dat, u_char *
 
 static int nand_davinci_dev_ready(struct mtd_info *mtd)
 {
-	emifregs	emif_addr;
-
-	emif_addr = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
-
-	return(emif_addr->NANDFSR & 0x1);
-}
-
-static int nand_davinci_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
-{
-	while(!nand_davinci_dev_ready(mtd)) {;}
-	*NAND_CE0CLE = NAND_STATUS;
-	return(*NAND_CE0DATA);
+	return emif_regs->NANDFSR & 0x1;
 }
 
 static void nand_flash_init(void)
 {
+	/* This is for DM6446 EVM and *very* similar.  DO NOT GROW THIS!
+	 * Instead, have your board_init() set EMIF timings, based on its
+	 * knowledge of the clocks and what devices are hooked up ... and
+	 * don't even do that unless no UBL handled it.
+	 */
+#ifdef CONFIG_SOC_DM6446
 	u_int32_t	acfg1 = 0x3ffffffc;
-	emifregs	emif_regs;
 
 	/*------------------------------------------------------------------*
 	 *  NAND FLASH CHIP TIMEOUT @ 459 MHz                               *
@@ -408,17 +401,14 @@ static void nand_flash_init(void)
 		| (0 << 0 )	/* asyncSize	8-bit bus */
 		;
 
-	emif_regs = (emifregs)DAVINCI_ASYNC_EMIF_CNTRL_BASE;
-
 	emif_regs->AB1CR = acfg1; /* CS2 */
 
 	emif_regs->NANDFCR = 0x00000101; /* NAND flash on CS2 */
+#endif
 }
 
 int board_nand_init(struct nand_chip *nand)
 {
-	nand->IO_ADDR_R   = (void  __iomem *)NAND_CE0DATA;
-	nand->IO_ADDR_W   = (void  __iomem *)NAND_CE0DATA;
 	nand->chip_delay  = 0;
 	nand->select_chip = nand_davinci_select_chip;
 #ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
@@ -452,7 +442,6 @@ int board_nand_init(struct nand_chip *nand)
 	nand->cmd_ctrl = nand_davinci_hwcontrol;
 
 	nand->dev_ready = nand_davinci_dev_ready;
-	nand->waitfunc = nand_davinci_waitfunc;
 
 	nand_flash_init();
 

include/asm-arm/arch-davinci/nand_defs.h

@@ -31,60 +31,6 @@
 #define	MASK_CLE	0x10
 #define	MASK_ALE	0x0a
 
-#define NAND_CE0CLE	((volatile u_int8_t *)(CONFIG_SYS_NAND_BASE + 0x10))
-#define NAND_CE0ALE	((volatile u_int8_t *)(CONFIG_SYS_NAND_BASE + 0x0a))
-#define NAND_CE0DATA	((volatile u_int8_t *)CONFIG_SYS_NAND_BASE)
-
-typedef struct  {
-	u_int32_t	NRCSR;
-	u_int32_t	AWCCR;
-	u_int8_t	RSVD0[8];
-	u_int32_t	AB1CR;
-	u_int32_t	AB2CR;
-	u_int32_t	AB3CR;
-	u_int32_t	AB4CR;
-	u_int8_t	RSVD1[32];
-	u_int32_t	NIRR;
-	u_int32_t	NIMR;
-	u_int32_t	NIMSR;
-	u_int32_t	NIMCR;
-	u_int8_t	RSVD2[16];
-	u_int32_t	NANDFCR;
-	u_int32_t	NANDFSR;
-	u_int8_t	RSVD3[8];
-	u_int32_t	NANDF1ECC;
-	u_int32_t	NANDF2ECC;
-	u_int32_t	NANDF3ECC;
-	u_int32_t	NANDF4ECC;
-	u_int8_t	RSVD4[4];
-	u_int32_t	IODFTECR;
-	u_int32_t	IODFTGCR;
-	u_int8_t	RSVD5[4];
-	u_int32_t	IODFTMRLR;
-	u_int32_t	IODFTMRMR;
-	u_int32_t	IODFTMRMSBR;
-	u_int8_t	RSVD6[20];
-	u_int32_t	MODRNR;
-	u_int8_t	RSVD7[76];
-	u_int32_t	CE0DATA;
-	u_int32_t	CE0ALE;
-	u_int32_t	CE0CLE;
-	u_int8_t	RSVD8[4];
-	u_int32_t	CE1DATA;
-	u_int32_t	CE1ALE;
-	u_int32_t	CE1CLE;
-	u_int8_t	RSVD9[4];
-	u_int32_t	CE2DATA;
-	u_int32_t	CE2ALE;
-	u_int32_t	CE2CLE;
-	u_int8_t	RSVD10[4];
-	u_int32_t	CE3DATA;
-	u_int32_t	CE3ALE;
-	u_int32_t	CE3CLE;
-} nand_registers;
-
-typedef volatile nand_registers	*nandregs;
-
 #define NAND_READ_START		0x00
 #define NAND_READ_END		0x30
 #define NAND_STATUS		0x70