i386: Replace [read, write]_mmcr_[byte, word, long] with memory mapped structure

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>

board/eNET/eNET.c

@@ -46,7 +46,7 @@ unsigned long monitor_flash_len = CONFIG_SYS_MONITOR_LEN;
 void init_sc520_enet (void)
 {
 	/* Set CPU Speed to 100MHz */
-	write_mmcr_byte(SC520_CPUCTL, 1);
+	sc520_mmcr->cpuctl = 0x01;
 	gd->cpu_clk = 100000000;
 
 	/* wait at least one millisecond */
@@ -56,7 +56,7 @@ void init_sc520_enet (void)
 	    "loop 0b\n": : : "ecx");
 
 	/* turn on the SDRAM write buffer */
-	write_mmcr_byte(SC520_DBCTL, 0x11);
+	sc520_mmcr->dbctl = 0x11;
 
 	/* turn on the cache and disable write through */
 	asm("movl	%%cr0, %%eax\n"
@@ -71,51 +71,51 @@ int board_init(void)
 {
 	init_sc520_enet();
 
-	write_mmcr_byte(SC520_GPCSRT, 0x01);		/* GP Chip Select Recovery Time */
-	write_mmcr_byte(SC520_GPCSPW, 0x07);		/* GP Chip Select Pulse Width */
-	write_mmcr_byte(SC520_GPCSOFF, 0x00);		/* GP Chip Select Offset */
-	write_mmcr_byte(SC520_GPRDW, 0x05);		/* GP Read pulse width */
-	write_mmcr_byte(SC520_GPRDOFF, 0x01);		/* GP Read offset */
-	write_mmcr_byte(SC520_GPWRW, 0x05);		/* GP Write pulse width */
-	write_mmcr_byte(SC520_GPWROFF, 0x01);		/* GP Write offset */
-
-	write_mmcr_word(SC520_PIODATA15_0, 0x0630);	/* PIO15_PIO0 Data */
-	write_mmcr_word(SC520_PIODATA31_16, 0x2000);	/* PIO31_PIO16 Data */
-	write_mmcr_word(SC520_PIODIR31_16, 0x2000);	/* GPIO Direction */
-	write_mmcr_word(SC520_PIODIR15_0, 0x87b5);	/* GPIO Direction */
-	write_mmcr_word(SC520_PIOPFS31_16, 0x0dfe);	/* GPIO pin function 31-16 reg */
-	write_mmcr_word(SC520_PIOPFS15_0, 0x200a);	/* GPIO pin function 15-0 reg */
-	write_mmcr_byte(SC520_CSPFS, 0x00f8);		/* Chip Select Pin Function Select */
-
-	write_mmcr_long(SC520_PAR2, 0x200713f8);	/* Uart A (GPCS0, 0x013f8, 8 Bytes) */
-	write_mmcr_long(SC520_PAR3, 0x2c0712f8);	/* Uart B (GPCS3, 0x012f8, 8 Bytes) */
-	write_mmcr_long(SC520_PAR4, 0x300711f8);	/* Uart C (GPCS4, 0x011f8, 8 Bytes) */
-	write_mmcr_long(SC520_PAR5, 0x340710f8);	/* Uart D (GPCS5, 0x010f8, 8 Bytes) */
-	write_mmcr_long(SC520_PAR6, 0xe3ffc000);	/* SDRAM (0x00000000, 128MB) */
-	write_mmcr_long(SC520_PAR7, 0xaa3fd000);	/* StrataFlash (ROMCS1, 0x10000000, 16MB) */
-	write_mmcr_long(SC520_PAR8, 0xca3fd100);	/* StrataFlash (ROMCS2, 0x11000000, 16MB) */
-	write_mmcr_long(SC520_PAR9, 0x4203d900);	/* SRAM (GPCS0, 0x19000000, 1MB) */
-	write_mmcr_long(SC520_PAR10, 0x4e03d910);	/* SRAM (GPCS3, 0x19100000, 1MB) */
-	write_mmcr_long(SC520_PAR11, 0x50018100);	/* DP-RAM (GPCS4, 0x18100000, 4kB) */
-	write_mmcr_long(SC520_PAR12, 0x54020000);	/* CFLASH1 (0x200000000, 4kB) */
-	write_mmcr_long(SC520_PAR13, 0x5c020001);	/* CFLASH2 (0x200010000, 4kB) */
-/*	write_mmcr_long(SC520_PAR14, 0x8bfff800); */	/* BOOTCS at  0x18000000 */
-/*	write_mmcr_long(SC520_PAR15, 0x38201000); */	/* LEDs etc (GPCS6, 0x1000, 20 Bytes */
+	sc520_mmcr->gpcsrt = 0x01;		/* GP Chip Select Recovery Time */
+	sc520_mmcr->gpcspw = 0x07;		/* GP Chip Select Pulse Width */
+	sc520_mmcr->gpcsoff = 0x00;		/* GP Chip Select Offset */
+	sc520_mmcr->gprdw = 0x05;		/* GP Read pulse width */
+	sc520_mmcr->gprdoff = 0x01;		/* GP Read offset */
+	sc520_mmcr->gpwrw = 0x05;		/* GP Write pulse width */
+	sc520_mmcr->gpwroff = 0x01;		/* GP Write offset */
+
+	sc520_mmcr->piodata15_0 = 0x0630;	/* PIO15_PIO0 Data */
+	sc520_mmcr->piodata31_16 = 0x2000;	/* PIO31_PIO16 Data */
+	sc520_mmcr->piodir31_16 = 0x2000;	/* GPIO Direction */
+	sc520_mmcr->piodir15_0 = 0x87b5;	/* GPIO Direction */
+	sc520_mmcr->piopfs31_16 = 0x0dfe;	/* GPIO pin function 31-16 reg */
+	sc520_mmcr->piopfs15_0 = 0x200a;	/* GPIO pin function 15-0 reg */
+	sc520_mmcr->cspfs = 0x00f8;		/* Chip Select Pin Function Select */
+
+	sc520_mmcr->par[2] = 0x200713f8;	/* Uart A (GPCS0, 0x013f8, 8 Bytes) */
+	sc520_mmcr->par[3] = 0x2c0712f8;	/* Uart B (GPCS3, 0x012f8, 8 Bytes) */
+	sc520_mmcr->par[4] = 0x300711f8;	/* Uart C (GPCS4, 0x011f8, 8 Bytes) */
+	sc520_mmcr->par[5] = 0x340710f8;	/* Uart D (GPCS5, 0x010f8, 8 Bytes) */
+	sc520_mmcr->par[6] =  0xe3ffc000;	/* SDRAM (0x00000000, 128MB) */
+	sc520_mmcr->par[7] = 0xaa3fd000;	/* StrataFlash (ROMCS1, 0x10000000, 16MB) */
+	sc520_mmcr->par[8] = 0xca3fd100;	/* StrataFlash (ROMCS2, 0x11000000, 16MB) */
+	sc520_mmcr->par[9] = 0x4203d900;	/* SRAM (GPCS0, 0x19000000, 1MB) */
+	sc520_mmcr->par[10] = 0x4e03d910;	/* SRAM (GPCS3, 0x19100000, 1MB) */
+	sc520_mmcr->par[11] = 0x50018100;	/* DP-RAM (GPCS4, 0x18100000, 4kB) */
+	sc520_mmcr->par[12] = 0x54020000;	/* CFLASH1 (0x200000000, 4kB) */
+	sc520_mmcr->par[13] = 0x5c020001;	/* CFLASH2 (0x200010000, 4kB) */
+/*	sc520_mmcr->par14 = 0x8bfff800; */	/* BOOTCS at  0x18000000 */
+/*	sc520_mmcr->par15 = 0x38201000; */	/* LEDs etc (GPCS6, 0x1000, 20 Bytes */
 
 	/* Disable Watchdog */
-	write_mmcr_word(0x0cb0, 0x3333);
-	write_mmcr_word(0x0cb0, 0xcccc);
-	write_mmcr_word(0x0cb0, 0x0000);
+	sc520_mmcr->wdtmrctl = 0x3333;
+	sc520_mmcr->wdtmrctl = 0xcccc;
+	sc520_mmcr->wdtmrctl = 0x0000;
 
 	/* Chip Select Configuration */
-	write_mmcr_word(SC520_BOOTCSCTL, 0x0033);
-	write_mmcr_word(SC520_ROMCS1CTL, 0x0615);
-	write_mmcr_word(SC520_ROMCS2CTL, 0x0615);
-
-	write_mmcr_byte(SC520_ADDDECCTL, 0x02);
-	write_mmcr_byte(SC520_UART1CTL, 0x07);
-	write_mmcr_byte(SC520_SYSARBCTL,0x06);
-	write_mmcr_word(SC520_SYSARBMENB, 0x0003);
+	sc520_mmcr->bootcsctl = 0x0033;
+	sc520_mmcr->romcs1ctl = 0x0615;
+	sc520_mmcr->romcs2ctl = 0x0615;
+
+	sc520_mmcr->adddecctl = 0x02;
+	sc520_mmcr->uart1ctl = 0x07;
+	sc520_mmcr->sysarbctl = 0x06;
+	sc520_mmcr->sysarbmenb = 0x0003;
 
 	/* Crystal is 33.000MHz */
 	gd->bus_clk = 33000000;

board/sc520_cdp/flash.c

@@ -337,12 +337,12 @@ done:	;
 	unsigned micro; \
 	unsigned milli=0; \
 	\
-	micro = *(volatile u16*)(0xfffef000+SC520_SWTMRMILLI); \
+	micro = sc520_mmcr->swtmrmilli; \
 	 \
 	for (;;) { \
 		\
-		milli += *(volatile u16*)(0xfffef000+SC520_SWTMRMILLI); \
-		micro = *(volatile u16*)(0xfffef000+SC520_SWTMRMICRO); \
+		milli += sc520_mmcr->swtmrmilli; \
+		micro = sc520_mmcr->swtmrmicro; \
 		\
 		if ((delay) <= (micro + (milli * 1000))) { \
 			break; \
@@ -364,12 +364,12 @@ static u32 _amd_erase_flash(u32 addr, u32 sector)
 	/* Sector erase command comes last */
 	*(volatile u32*)(addr + sector) = 0x30303030;
 
-	elapsed = *(volatile u16*)(0xfffef000+SC520_SWTMRMILLI); /* dummy read */
+	elapsed = sc520_mmcr->swtmrmilli; /* dummy read */
 	elapsed = 0;
 	__udelay(50);
 	while (((*(volatile u32*)(addr + sector)) & 0x80808080) != 0x80808080) {
 
-		elapsed += *(volatile u16*)(0xfffef000+SC520_SWTMRMILLI);
+		elapsed += sc520_mmcr->swtmrmilli;
 		if (elapsed > ((CONFIG_SYS_FLASH_ERASE_TOUT/CONFIG_SYS_HZ) * 1000)) {
 			*(volatile u32*)(addr) = 0xf0f0f0f0;
 			return 1;
@@ -487,12 +487,12 @@ static int _amd_write_word(unsigned start, unsigned dest, unsigned data)
 
 	dest2[0] = data;
 
-	elapsed = *(volatile u16*)(0xfffef000+SC520_SWTMRMILLI); /* dummy read */
+	elapsed = sc520_mmcr->swtmrmilli; /* dummy read */
 	elapsed = 0;
 
 	/* data polling for D7 */
 	while ((dest2[0] & 0x80808080) != (data2[0] & 0x80808080)) {
-		elapsed += *(volatile u16*)(0xfffef000+SC520_SWTMRMILLI);
+		elapsed += sc520_mmcr->swtmrmilli;
 		if (elapsed > ((CONFIG_SYS_FLASH_WRITE_TOUT/CONFIG_SYS_HZ) * 1000)) {
 			addr2[0] = 0xf0f0f0f0;
 			return 1;

board/sc520_cdp/sc520_cdp.c

@@ -58,61 +58,60 @@ DECLARE_GLOBAL_DATA_PTR;
 static void irq_init(void)
 {
 	/* disable global interrupt mode */
-	write_mmcr_byte(SC520_PICICR, 0x40);
+	sc520_mmcr->picicr = 0x40;
 
 	/* set all irqs to edge */
-	write_mmcr_byte(SC520_MPICMODE, 0x00);
-	write_mmcr_byte(SC520_SL1PICMODE, 0x00);
-	write_mmcr_byte(SC520_SL2PICMODE, 0x00);
+	sc520_mmcr->pic_mode[0] = 0x00;
+	sc520_mmcr->pic_mode[1] = 0x00;
+	sc520_mmcr->pic_mode[2] = 0x00;
 
 	/* active low polarity on PIC interrupt pins,
 	 *  active high polarity on all other irq pins */
-	write_mmcr_word(SC520_INTPINPOL, 0x0000);
+	sc520_mmcr->intpinpol = 0x0000;
 
 	/* set irq number mapping */
-	write_mmcr_byte(SC520_GPTMR0MAP, SC520_IRQ_DISABLED);   /* disable GP timer 0 INT */
-	write_mmcr_byte(SC520_GPTMR1MAP, SC520_IRQ_DISABLED);   /* disable GP timer 1 INT */
-	write_mmcr_byte(SC520_GPTMR2MAP, SC520_IRQ_DISABLED);   /* disable GP timer 2 INT */
-	write_mmcr_byte(SC520_PIT0MAP, SC520_IRQ0);             /* Set PIT timer 0 INT to IRQ0 */
-	write_mmcr_byte(SC520_PIT1MAP, SC520_IRQ_DISABLED);     /* disable PIT timer 1 INT */
-	write_mmcr_byte(SC520_PIT2MAP, SC520_IRQ_DISABLED);     /* disable PIT timer 2 INT */
-	write_mmcr_byte(SC520_PCIINTAMAP, SC520_IRQ_DISABLED);  /* disable PCI INT A */
-	write_mmcr_byte(SC520_PCIINTBMAP, SC520_IRQ_DISABLED);  /* disable PCI INT B */
-	write_mmcr_byte(SC520_PCIINTCMAP, SC520_IRQ_DISABLED);  /* disable PCI INT C */
-	write_mmcr_byte(SC520_PCIINTDMAP, SC520_IRQ_DISABLED);  /* disable PCI INT D */
-	write_mmcr_byte(SC520_DMABCINTMAP, SC520_IRQ_DISABLED); /* disable DMA INT */
-	write_mmcr_byte(SC520_SSIMAP, SC520_IRQ_DISABLED);      /* disable Synchronius serial INT */
-	write_mmcr_byte(SC520_WDTMAP, SC520_IRQ_DISABLED);      /* disable Watchdog INT */
-	write_mmcr_byte(SC520_RTCMAP, SC520_IRQ8);              /* Set RTC int to 8 */
-	write_mmcr_byte(SC520_WPVMAP, SC520_IRQ_DISABLED);      /* disable write protect INT */
-	write_mmcr_byte(SC520_ICEMAP, SC520_IRQ1);              /* Set ICE Debug Serielport INT to IRQ1 */
-	write_mmcr_byte(SC520_FERRMAP,SC520_IRQ13);             /* Set FP error INT to IRQ13 */
+	sc520_mmcr->gp_tmr_int_map[0] = SC520_IRQ_DISABLED;	/* disable GP timer 0 INT */
+	sc520_mmcr->gp_tmr_int_map[1] = SC520_IRQ_DISABLED;	/* disable GP timer 1 INT */
+	sc520_mmcr->gp_tmr_int_map[2] = SC520_IRQ_DISABLED;	/* disable GP timer 2 INT */
+	sc520_mmcr->pit_int_map[0] = SC520_IRQ0;		/* Set PIT timer 0 INT to IRQ0 */
+	sc520_mmcr->pit_int_map[1] = SC520_IRQ_DISABLED;	/* disable PIT timer 1 INT */
+	sc520_mmcr->pit_int_map[2] = SC520_IRQ_DISABLED;	/* disable PIT timer 2 INT */
+	sc520_mmcr->pci_int_map[0] = SC520_IRQ_DISABLED;	/* disable PCI INT A */
+	sc520_mmcr->pci_int_map[1] = SC520_IRQ_DISABLED;	/* disable PCI INT B */
+	sc520_mmcr->pci_int_map[2] = SC520_IRQ_DISABLED;	/* disable PCI INT C */
+	sc520_mmcr->pci_int_map[3] = SC520_IRQ_DISABLED;	/* disable PCI INT D */
+	sc520_mmcr->dmabcintmap = SC520_IRQ_DISABLED;		/* disable DMA INT */
+	sc520_mmcr->ssimap = SC520_IRQ_DISABLED;		/* disable Synchronius serial INT */
+	sc520_mmcr->wdtmap = SC520_IRQ_DISABLED;		/* disable Watchdog INT */
+	sc520_mmcr->rtcmap = SC520_IRQ8;			/* Set RTC int to 8 */
+	sc520_mmcr->wpvmap = SC520_IRQ_DISABLED;		/* disable write protect INT */
+	sc520_mmcr->icemap = SC520_IRQ1;			/* Set ICE Debug Serielport INT to IRQ1 */
+	sc520_mmcr->ferrmap = SC520_IRQ13; 			/* Set FP error INT to IRQ13 */
 
 	if (CONFIG_SYS_USE_SIO_UART) {
-		write_mmcr_byte(SC520_UART1MAP, SC520_IRQ_DISABLED); /* disable internal UART1 INT */
-		write_mmcr_byte(SC520_UART2MAP, SC520_IRQ_DISABLED); /* disable internal UART2 INT */
-		write_mmcr_byte(SC520_GP3IMAP, SC520_IRQ3);          /* Set GPIRQ3 (ISA IRQ3) to IRQ3 */
-		write_mmcr_byte(SC520_GP4IMAP, SC520_IRQ4);          /* Set GPIRQ4 (ISA IRQ4) to IRQ4 */
+		sc520_mmcr->uart_int_map[0] = SC520_IRQ_DISABLED;	/* disable internal UART1 INT */
+		sc520_mmcr->uart_int_map[1] = SC520_IRQ_DISABLED;	/* disable internal UART2 INT */
+		sc520_mmcr->gp_int_map[3] = SC520_IRQ3;		/* Set GPIRQ3 (ISA IRQ3) to IRQ3 */
+		sc520_mmcr->gp_int_map[4] = SC520_IRQ4;		/* Set GPIRQ4 (ISA IRQ4) to IRQ4 */
 	} else {
-		write_mmcr_byte(SC520_UART1MAP, SC520_IRQ4);         /* Set internal UART2 INT to IRQ4 */
-		write_mmcr_byte(SC520_UART2MAP, SC520_IRQ3);         /* Set internal UART2 INT to IRQ3 */
-		write_mmcr_byte(SC520_GP3IMAP, SC520_IRQ_DISABLED);  /* disable GPIRQ3 (ISA IRQ3) */
-		write_mmcr_byte(SC520_GP4IMAP, SC520_IRQ_DISABLED);  /* disable GPIRQ4 (ISA IRQ4) */
+		sc520_mmcr->uart_int_map[0] = SC520_IRQ4;		/* Set internal UART2 INT to IRQ4 */
+		sc520_mmcr->uart_int_map[1] = SC520_IRQ3;		/* Set internal UART2 INT to IRQ3 */
+		sc520_mmcr->gp_int_map[3] = SC520_IRQ_DISABLED;	/* disable GPIRQ3 (ISA IRQ3) */
+		sc520_mmcr->gp_int_map[4] = SC520_IRQ_DISABLED;	/* disable GPIRQ4 (ISA IRQ4) */
 	}
 
-	write_mmcr_byte(SC520_GP1IMAP, SC520_IRQ1);             /* Set GPIRQ1 (SIO IRQ1) to IRQ1 */
-	write_mmcr_byte(SC520_GP5IMAP, SC520_IRQ5);             /* Set GPIRQ5 (ISA IRQ5) to IRQ5 */
-	write_mmcr_byte(SC520_GP6IMAP, SC520_IRQ6);             /* Set GPIRQ6 (ISA IRQ6) to IRQ6 */
-	write_mmcr_byte(SC520_GP7IMAP, SC520_IRQ7);             /* Set GPIRQ7 (ISA IRQ7) to IRQ7 */
-	write_mmcr_byte(SC520_GP8IMAP, SC520_IRQ8);             /* Set GPIRQ8 (SIO IRQ8) to IRQ8 */
-	write_mmcr_byte(SC520_GP9IMAP, SC520_IRQ9);             /* Set GPIRQ9 (ISA IRQ2) to IRQ9 */
-	write_mmcr_byte(SC520_GP0IMAP, SC520_IRQ11);            /* Set GPIRQ0 (ISA IRQ11) to IRQ10 */
-	write_mmcr_byte(SC520_GP2IMAP, SC520_IRQ12);            /* Set GPIRQ2 (ISA IRQ12) to IRQ12 */
-	write_mmcr_byte(SC520_GP10IMAP,SC520_IRQ14);            /* Set GPIRQ10 (ISA IRQ14) to IRQ14 */
-
-	write_mmcr_word(SC520_PCIHOSTMAP, 0x11f);                /* Map PCI hostbridge INT to NMI */
-	write_mmcr_word(SC520_ECCMAP, 0x100);                    /* Map SDRAM ECC failure INT to NMI */
-
+	sc520_mmcr->gp_int_map[1] = SC520_IRQ1;			/* Set GPIRQ1 (SIO IRQ1) to IRQ1 */
+	sc520_mmcr->gp_int_map[5] = SC520_IRQ5;			/* Set GPIRQ5 (ISA IRQ5) to IRQ5 */
+	sc520_mmcr->gp_int_map[6] = SC520_IRQ6;			/* Set GPIRQ6 (ISA IRQ6) to IRQ6 */
+	sc520_mmcr->gp_int_map[7] = SC520_IRQ7;			/* Set GPIRQ7 (ISA IRQ7) to IRQ7 */
+	sc520_mmcr->gp_int_map[8] = SC520_IRQ8;			/* Set GPIRQ8 (SIO IRQ8) to IRQ8 */
+	sc520_mmcr->gp_int_map[9] = SC520_IRQ9;			/* Set GPIRQ9 (ISA IRQ2) to IRQ9 */
+	sc520_mmcr->gp_int_map[0] = SC520_IRQ11;		/* Set GPIRQ0 (ISA IRQ11) to IRQ10 */
+	sc520_mmcr->gp_int_map[2] = SC520_IRQ12;		/* Set GPIRQ2 (ISA IRQ12) to IRQ12 */
+	sc520_mmcr->gp_int_map[10] = SC520_IRQ14;		/* Set GPIRQ10 (ISA IRQ14) to IRQ14 */
+
+	sc520_mmcr->pcihostmap = 0x11f;				/* Map PCI hostbridge INT to NMI */
+	sc520_mmcr->eccmap = 0x100;				/* Map SDRAM ECC failure INT to NMI */
 }
 
 #ifdef CONFIG_PCI
@@ -235,23 +234,22 @@ static void bus_init(void)
 {
 
 	/* set up the GP IO pins */
-	write_mmcr_word(SC520_PIOPFS31_16, 0xf7ff);	/* set the GPIO pin function 31-16 reg */
-	write_mmcr_word(SC520_PIOPFS15_0, 0xffff);	/* set the GPIO pin function 15-0 reg */
-	write_mmcr_byte(SC520_CSPFS, 0xf8);		/* set the CS pin function  reg */
-	write_mmcr_byte(SC520_CLKSEL, 0x70);
-
-
-	write_mmcr_byte(SC520_GPCSRT, 1);   /* set the GP CS offset */
-	write_mmcr_byte(SC520_GPCSPW, 3);   /* set the GP CS pulse width */
-	write_mmcr_byte(SC520_GPCSOFF, 1);  /* set the GP CS offset */
-	write_mmcr_byte(SC520_GPRDW, 3);    /* set the RD pulse width */
-	write_mmcr_byte(SC520_GPRDOFF, 1);  /* set the GP RD offset */
-	write_mmcr_byte(SC520_GPWRW, 3);    /* set the GP WR pulse width */
-	write_mmcr_byte(SC520_GPWROFF, 1);  /* set the GP WR offset */
-
-	write_mmcr_word(SC520_BOOTCSCTL, 0x1823);		/* set up timing of BOOTCS */
-	write_mmcr_word(SC520_ROMCS1CTL, 0x1823);		/* set up timing of ROMCS1 */
-	write_mmcr_word(SC520_ROMCS2CTL, 0x1823);		/* set up timing of ROMCS2 */
+	sc520_mmcr->piopfs31_16 = 0xf7ff;	/* set the GPIO pin function 31-16 reg */
+	sc520_mmcr->piopfs15_0 = 0xffff;	/* set the GPIO pin function 15-0 reg */
+	sc520_mmcr->cspfs = 0xf8;		/* set the CS pin function  reg */
+	sc520_mmcr->clksel = 0x70;
+
+	sc520_mmcr->gpcsrt = 1;   		/* set the GP CS offset */
+	sc520_mmcr->gpcspw = 3;   		/* set the GP CS pulse width */
+	sc520_mmcr->gpcsoff = 1;  		/* set the GP CS offset */
+	sc520_mmcr->gprdw = 3;    		/* set the RD pulse width */
+	sc520_mmcr->gprdoff = 1;  		/* set the GP RD offset */
+	sc520_mmcr->gpwrw = 3;   		 /* set the GP WR pulse width */
+	sc520_mmcr->gpwroff = 1; 		 /* set the GP WR offset */
+
+	sc520_mmcr->bootcsctl = 0x1823;		/* set up timing of BOOTCS */
+	sc520_mmcr->romcs1ctl = 0x1823;		/* set up timing of ROMCS1 */
+	sc520_mmcr->romcs2ctl = 0x1823;		/* set up timing of ROMCS2 */
 
 	/* adjust the memory map:
 	 * by default the first 256MB (0x00000000 - 0x0fffffff) is mapped to SDRAM
@@ -260,31 +258,31 @@ static void bus_init(void)
 
 
 	/* SRAM = GPCS3 128k @ d0000-effff*/
-	write_mmcr_long(SC520_PAR2,  0x4e00400d);
+	sc520_mmcr->par[2] = 0x4e00400d;
 
 	/* IDE0 = GPCS6 1f0-1f7 */
-	write_mmcr_long(SC520_PAR3,  0x380801f0);
+	sc520_mmcr->par[3] = 0x380801f0;
 
 	/* IDE1 = GPCS7 3f6 */
-	write_mmcr_long(SC520_PAR4,  0x3c0003f6);
+	sc520_mmcr->par[4] = 0x3c0003f6;
 	/* bootcs */
-	write_mmcr_long(SC520_PAR12, 0x8bffe800);
+	sc520_mmcr->par[12] = 0x8bffe800;
 	/* romcs2 */
-	write_mmcr_long(SC520_PAR13, 0xcbfff000);
+	sc520_mmcr->par[13] = 0xcbfff000;
 	/* romcs1 */
-	write_mmcr_long(SC520_PAR14, 0xabfff800);
+	sc520_mmcr->par[14] = 0xabfff800;
 	/* 680 LEDS */
-	write_mmcr_long(SC520_PAR15, 0x30000640);
+	sc520_mmcr->par[15] = 0x30000640;
 
-	write_mmcr_byte(SC520_ADDDECCTL, 0);
+	sc520_mmcr->adddecctl = 0;
 
 	asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */
 
 	if (CONFIG_SYS_USE_SIO_UART) {
-		write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) | UART2_DIS|UART1_DIS);
+		sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | UART2_DIS | UART1_DIS;
 		setup_ali_sio(1);
 	} else {
-		write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));
+		sc520_mmcr->adddecctl = sc520_mmcr->adddecctl & ~(UART2_DIS|UART1_DIS);
 		setup_ali_sio(0);
 		silence_uart(0x3e8);
 		silence_uart(0x2e8);
@@ -352,7 +350,7 @@ u32 isa_map_rom(u32 bus_addr, int size)
 	PRINTF ("setting PAR11 to %x\n", par);
 
 	/* Map rom 0x10000 with PAR1 */
-	write_mmcr_long(SC520_PAR11,  par);
+	sc520_mmcr->par[11] = par;
 
 	return bus_addr;
 }
@@ -364,8 +362,8 @@ u32 isa_map_rom(u32 bus_addr, int size)
 void isa_unmap_rom(u32 addr)
 {
 	PRINTF("isa_unmap_rom asked to unmap %x", addr);
-	if ((addr>>12) == (read_mmcr_long(SC520_PAR11)&0x3ffff)) {
-		write_mmcr_long(SC520_PAR11, 0);
+	if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) {
+		sc520_mmcr->par[11] = 0;
 		PRINTF(" done\n");
 		return;
 	}
@@ -401,7 +399,7 @@ u32 pci_get_rom_window(struct pci_controller *hose, int size)
 	PRINTF ("setting PAR1 to %x\n", par);
 
 	/* Map rom 0x10000 with PAR1 */
-	write_mmcr_long(SC520_PAR1,  par);
+	sc520_mmcr->par[1] = par;
 
 	return PCI_ROM_TEMP_SPACE;
 }
@@ -414,7 +412,7 @@ void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
 {
 	PRINTF("pci_remove_rom_window: %x", addr);
 	if (addr == PCI_ROM_TEMP_SPACE) {
-		write_mmcr_long(SC520_PAR1, 0);
+		sc520_mmcr->par[1] = 0;
 		PRINTF(" done\n");
 		return;
 	}
@@ -432,11 +430,10 @@ void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
 int pci_enable_legacy_video_ports(struct pci_controller *hose)
 {
 	/* Map video memory to 0xa0000*/
-	write_mmcr_long(SC520_PAR0,  0x7200400a);
+	sc520_mmcr->par[0] = 0x7200400a;
 
 	/* forward all I/O accesses to PCI */
-	write_mmcr_byte(SC520_ADDDECCTL,
-			read_mmcr_byte(SC520_ADDDECCTL) | IO_HOLE_DEST_PCI);
+	sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI;
 
 
 	/* so we map away all io ports to pci (only way to access pci io
@@ -446,32 +443,32 @@ int pci_enable_legacy_video_ports(struct pci_controller *hose)
 	 */
 
 	/* bring 0x100 - 0x1ef back to ISA using PAR5 */
-	write_mmcr_long(SC520_PAR5, 0x30ef0100);
+	sc520_mmcr->par[5] = 0x30ef0100;
 
 	/* IDE use 1f0-1f7 */
 
 	/* bring 0x1f8 - 0x2f7 back to ISA using PAR6 */
-	write_mmcr_long(SC520_PAR6, 0x30ff01f8);
+	sc520_mmcr->par[6] = 0x30ff01f8;
 
 	/* com2 use 2f8-2ff */
 
 	/* bring 0x300 - 0x3af back to ISA using PAR7 */
-	write_mmcr_long(SC520_PAR7, 0x30af0300);
+	sc520_mmcr->par[7] = 0x30af0300;
 
 	/* vga use 3b0-3bb */
 
 	/* bring 0x3bc - 0x3bf back to ISA using PAR8 */
-	write_mmcr_long(SC520_PAR8, 0x300303bc);
+	sc520_mmcr->par[8] = 0x300303bc;
 
 	/* vga use 3c0-3df */
 
 	/* bring 0x3e0 - 0x3f5 back to ISA using PAR9 */
-	write_mmcr_long(SC520_PAR9, 0x301503e0);
+	sc520_mmcr->par[9] = 0x301503e0;
 
 	/* ide use 3f6 */
 
 	/* bring 0x3f7  back to ISA using PAR10 */
-	write_mmcr_long(SC520_PAR10, 0x300003f7);
+	sc520_mmcr->par[10] = 0x300003f7;
 
 	/* com1 use 3f8-3ff */
 
@@ -490,12 +487,12 @@ int board_init(void)
 	irq_init();
 
 	/* max drive current on SDRAM */
-	write_mmcr_word(SC520_DSCTL, 0x0100);
+	sc520_mmcr->dsctl = 0x0100;
 
 	/* enter debug mode after next reset (only if jumper is also set) */
-	write_mmcr_byte(SC520_RESCFG, 0x08);
+	sc520_mmcr->rescfg = 0x08;
 	/* configure the software timer to 33.333MHz */
-	write_mmcr_byte(SC520_SWTMRCFG, 0);
+	sc520_mmcr->swtmrcfg = 0;
 	gd->bus_clk = 33333000;
 
 	return 0;

board/sc520_spunk/sc520_spunk.c

@@ -47,53 +47,54 @@ DECLARE_GLOBAL_DATA_PTR;
 static void irq_init(void)
 {
 	/* disable global interrupt mode */
-	write_mmcr_byte(SC520_PICICR, 0x40);
+	sc520_mmcr->picicr = 0x40;
 
 	/* set all irqs to edge */
-	write_mmcr_byte(SC520_MPICMODE, 0x00);
-	write_mmcr_byte(SC520_SL1PICMODE, 0x00);
-	write_mmcr_byte(SC520_SL2PICMODE, 0x00);
+	sc520_mmcr->pic_mode[0] = 0x00;
+	sc520_mmcr->pic_mode[1] = 0x00;
+	sc520_mmcr->pic_mode[2] = 0x00;
 
 	/* active low polarity on PIC interrupt pins,
 	 *  active high polarity on all other irq pins */
-	write_mmcr_word(SC520_INTPINPOL, 0x0000);
+	sc520_mmcr->intpinpol = 0x0000;
 
 	/* set irq number mapping */
-	write_mmcr_byte(SC520_GPTMR0MAP, SC520_IRQ_DISABLED);   /* disable GP timer 0 INT */
-	write_mmcr_byte(SC520_GPTMR1MAP, SC520_IRQ_DISABLED);   /* disable GP timer 1 INT */
-	write_mmcr_byte(SC520_GPTMR2MAP, SC520_IRQ_DISABLED);   /* disable GP timer 2 INT */
-	write_mmcr_byte(SC520_PIT0MAP, SC520_IRQ0);             /* Set PIT timer 0 INT to IRQ0 */
-	write_mmcr_byte(SC520_PIT1MAP, SC520_IRQ_DISABLED);     /* disable PIT timer 1 INT */
-	write_mmcr_byte(SC520_PIT2MAP, SC520_IRQ_DISABLED);     /* disable PIT timer 2 INT */
-	write_mmcr_byte(SC520_PCIINTAMAP, SC520_IRQ_DISABLED);  /* disable PCI INT A */
-	write_mmcr_byte(SC520_PCIINTBMAP, SC520_IRQ_DISABLED);  /* disable PCI INT B */
-	write_mmcr_byte(SC520_PCIINTCMAP, SC520_IRQ_DISABLED);  /* disable PCI INT C */
-	write_mmcr_byte(SC520_PCIINTDMAP, SC520_IRQ_DISABLED);  /* disable PCI INT D */
-	write_mmcr_byte(SC520_DMABCINTMAP, SC520_IRQ_DISABLED); /* disable DMA INT */
-	write_mmcr_byte(SC520_SSIMAP, SC520_IRQ6);              /* Set Synchronius serial INT to IRQ6*/
-	write_mmcr_byte(SC520_WDTMAP, SC520_IRQ_DISABLED);      /* disable Watchdog INT */
-	write_mmcr_byte(SC520_RTCMAP, SC520_IRQ8);              /* Set RTC int to 8 */
-	write_mmcr_byte(SC520_WPVMAP, SC520_IRQ_DISABLED);      /* disable write protect INT */
-	write_mmcr_byte(SC520_ICEMAP, SC520_IRQ1);              /* Set ICE Debug Serielport INT to IRQ1 */
-	write_mmcr_byte(SC520_FERRMAP,SC520_IRQ13);             /* Set FP error INT to IRQ13 */
-
-	write_mmcr_byte(SC520_UART1MAP, SC520_IRQ4);            /* Set internal UART2 INT to IRQ4 */
-	write_mmcr_byte(SC520_UART2MAP, SC520_IRQ3);            /* Set internal UART2 INT to IRQ3 */
-
-	write_mmcr_byte(SC520_GP0IMAP, SC520_IRQ7);             /* Set GPIRQ0 (PC-Card AUX IRQ) to IRQ7 */
-	write_mmcr_byte(SC520_GP1IMAP, SC520_IRQ14);            /* Set GPIRQ1 (CF IRQ) to IRQ14 */
-	write_mmcr_byte(SC520_GP3IMAP, SC520_IRQ5);             /* Set GPIRQ3 ( CAN IRQ ) ti IRQ5 */
-	write_mmcr_byte(SC520_GP4IMAP, SC520_IRQ_DISABLED);     /* disbale GIRQ4 ( IRR IRQ ) */
-	write_mmcr_byte(SC520_GP5IMAP, SC520_IRQ_DISABLED);     /* disable GPIRQ5 */
-	write_mmcr_byte(SC520_GP6IMAP, SC520_IRQ_DISABLED);     /* disable GPIRQ6 */
-	write_mmcr_byte(SC520_GP7IMAP, SC520_IRQ_DISABLED);     /* disable GPIRQ7 */
-	write_mmcr_byte(SC520_GP8IMAP, SC520_IRQ_DISABLED);     /* disable GPIRQ8 */
-	write_mmcr_byte(SC520_GP9IMAP, SC520_IRQ_DISABLED);     /* disable GPIRQ9 */
-	write_mmcr_byte(SC520_GP2IMAP, SC520_IRQ_DISABLED);     /* disable GPIRQ2 */
-	write_mmcr_byte(SC520_GP10IMAP,SC520_IRQ_DISABLED);     /* disable GPIRQ10 */
-
-	write_mmcr_word(SC520_PCIHOSTMAP, 0x11f);               /* Map PCI hostbridge INT to NMI */
-	write_mmcr_word(SC520_ECCMAP, 0x100);                   /* Map SDRAM ECC failure INT to NMI */
+	sc520_mmcr->gp_tmr_int_map[0] = SC520_IRQ_DISABLED;	/* disable GP timer 0 INT */
+	sc520_mmcr->gp_tmr_int_map[1] = SC520_IRQ_DISABLED;	/* disable GP timer 1 INT */
+	sc520_mmcr->gp_tmr_int_map[2] = SC520_IRQ_DISABLED;	/* disable GP timer 2 INT */
+	sc520_mmcr->pit_int_map[0] = SC520_IRQ0;		/* Set PIT timer 0 INT to IRQ0 */
+	sc520_mmcr->pit_int_map[1] = SC520_IRQ_DISABLED;	/* disable PIT timer 1 INT */
+	sc520_mmcr->pit_int_map[2] = SC520_IRQ_DISABLED;	/* disable PIT timer 2 INT */
+	sc520_mmcr->pci_int_map[0] = SC520_IRQ_DISABLED;	/* disable PCI INT A */
+	sc520_mmcr->pci_int_map[1] = SC520_IRQ_DISABLED;	/* disable PCI INT B */
+	sc520_mmcr->pci_int_map[2] = SC520_IRQ_DISABLED;	/* disable PCI INT C */
+	sc520_mmcr->pci_int_map[3] = SC520_IRQ_DISABLED;	/* disable PCI INT D */
+	sc520_mmcr->dmabcintmap = SC520_IRQ_DISABLED;		/* disable DMA INT */
+	sc520_mmcr->ssimap = SC520_IRQ6;			/* Set Synchronius serial INT to IRQ6*/
+	sc520_mmcr->wdtmap = SC520_IRQ_DISABLED;		/* disable Watchdog INT */
+	sc520_mmcr->rtcmap = SC520_IRQ8;			/* Set RTC int to 8 */
+	sc520_mmcr->wpvmap = SC520_IRQ_DISABLED;		/* disable write protect INT */
+	sc520_mmcr->icemap = SC520_IRQ1;			/* Set ICE Debug Serielport INT to IRQ1 */
+	sc520_mmcr->ferrmap = SC520_IRQ13; 			/* Set FP error INT to IRQ13 */
+
+
+	sc520_mmcr->uart_int_map[0] = SC520_IRQ4;		/* Set internal UART1 INT to IRQ4 */
+	sc520_mmcr->uart_int_map[1] = SC520_IRQ3;		/* Set internal UART2 INT to IRQ3 */
+
+	sc520_mmcr->gp_int_map[0] = SC520_IRQ7;			/* Set GPIRQ0 (PC-Card AUX IRQ) to IRQ7 */
+	sc520_mmcr->gp_int_map[1] = SC520_IRQ14;		/* Set GPIRQ1 (CF IRQ) to IRQ14 */
+	sc520_mmcr->gp_int_map[3] = SC520_IRQ5;			/* Set GPIRQ3 ( CAN IRQ ) ti IRQ5 */
+	sc520_mmcr->gp_int_map[4] = SC520_IRQ_DISABLED;		/* disbale GIRQ4 ( IRR IRQ ) */
+	sc520_mmcr->gp_int_map[5] = SC520_IRQ_DISABLED;		/* disable GPIRQ5 */
+	sc520_mmcr->gp_int_map[6] = SC520_IRQ_DISABLED;		/* disable GPIRQ6 */
+	sc520_mmcr->gp_int_map[7] = SC520_IRQ_DISABLED;		/* disable GPIRQ7 */
+	sc520_mmcr->gp_int_map[8] = SC520_IRQ_DISABLED;		/* disable GPIRQ8 */
+	sc520_mmcr->gp_int_map[9] = SC520_IRQ_DISABLED;		/* disable GPIRQ9 */
+	sc520_mmcr->gp_int_map[2] = SC520_IRQ_DISABLED;		/* disable GPIRQ2 */
+	sc520_mmcr->gp_int_map[10] = SC520_IRQ_DISABLED;	/* disable GPIRQ10 */
+
+	sc520_mmcr->pcihostmap = 0x11f;				/* Map PCI hostbridge INT to NMI */
+	sc520_mmcr->eccmap = 0x100;				/* Map SDRAM ECC failure INT to NMI */
 
 }
 
@@ -101,7 +102,7 @@ static void irq_init(void)
 /* PCI stuff */
 static void pci_sc520_spunk_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
 {
-	int version = read_mmcr_byte(SC520_SYSINFO);
+	int version = sc520_mmcr->sysinfo;
 
 	/* a configurable lists of irqs to steal
 	 * when we need one (a board with more pci interrupt pins
@@ -255,41 +256,41 @@ static void bus_init(void)
 	 * ??  Hyglo version 0.97 (small board)
 	 * 10  Spunk board
 	 */
-	int version = read_mmcr_byte(SC520_SYSINFO);
+	int version = sc520_mmcr->sysinfo;
 
 	if (version) {
 		/* set up the GP IO pins (for the Spunk board) */
-		write_mmcr_word(SC520_PIOPFS31_16, 0xfff0);	/* set the GPIO pin function 31-16 reg */
-		write_mmcr_word(SC520_PIOPFS15_0,  0x000f);	/* set the GPIO pin function 15-0 reg */
-		write_mmcr_word(SC520_PIODIR31_16, 0x000f);	/* set the GPIO direction 31-16 reg */
-		write_mmcr_word(SC520_PIODIR15_0,  0x1ff0);	/* set the GPIO direction 15-0 reg */
-		write_mmcr_byte(SC520_CSPFS, 0xc0);		/* set the CS pin function reg */
-		write_mmcr_byte(SC520_CLKSEL, 0x70);
+		sc520_mmcr->piopfs31_16 = 0xfff0;	/* set the GPIO pin function 31-16 reg */
+		sc520_mmcr->piopfs15_0 = 0x000f;	/* set the GPIO pin function 15-0 reg */
+		sc520_mmcr->piodir31_16 = 0x000f;	/* set the GPIO direction 31-16 reg */
+		sc520_mmcr->piodir15_0 = 0x1ff0;	/* set the GPIO direction 15-0 reg */
+		sc520_mmcr->cspfs = 0xc0;		/* set the CS pin function reg */
+		sc520_mmcr->clksel = 0x70;
 
-		write_mmcr_word(SC520_PIOCLR31_16, 0x0003);     /* reset SSI chip-selects */
-		write_mmcr_word(SC520_PIOSET31_16, 0x000c);
+		sc520_mmcr->pioclr31_16 = 0x0003;	/* reset SSI chip-selects */
+		sc520_mmcr->pioset31_16 = 0x000c;
 
 	} else {
 		/* set up the GP IO pins (for the Hyglo board) */
-		write_mmcr_word(SC520_PIOPFS31_16, 0xffc0);	/* set the GPIO pin function 31-16 reg */
-		write_mmcr_word(SC520_PIOPFS15_0, 0x1e7f);	/* set the GPIO pin function 15-0 reg */
-		write_mmcr_word(SC520_PIODIR31_16, 0x003f);	/* set the GPIO direction 31-16 reg */
-		write_mmcr_word(SC520_PIODIR15_0, 0xe180);	/* set the GPIO direction 15-0 reg */
-		write_mmcr_byte(SC520_CSPFS, 0x00);		/* set the CS pin function reg */
-		write_mmcr_byte(SC520_CLKSEL, 0x70);
-
-		write_mmcr_word(SC520_PIOCLR15_0, 0x0180);      /* reset SSI chip-selects */
+		sc520_mmcr->piopfs31_16 = 0xffc0;	/* set the GPIO pin function 31-16 reg */
+		sc520_mmcr->piopfs15_0 = 0x1e7f;	/* set the GPIO pin function 15-0 reg */
+		sc520_mmcr->piodir31_16 = 0x003f;	/* set the GPIO direction 31-16 reg */
+		sc520_mmcr->piodir15_0 = 0xe180;	/* set the GPIO direction 15-0 reg */
+		sc520_mmcr->cspfs = 0x00;		/* set the CS pin function reg */
+		sc520_mmcr->clksel = 0x70;
+
+		sc520_mmcr->pioclr15_0 = 0x0180;	/* reset SSI chip-selects */
 	}
 
-	write_mmcr_byte(SC520_GPCSRT, 1);   /* set the GP CS offset */
-	write_mmcr_byte(SC520_GPCSPW, 3);   /* set the GP CS pulse width */
-	write_mmcr_byte(SC520_GPCSOFF, 1);  /* set the GP CS offset */
-	write_mmcr_byte(SC520_GPRDW, 3);    /* set the RD pulse width */
-	write_mmcr_byte(SC520_GPRDOFF, 1);  /* set the GP RD offset */
-	write_mmcr_byte(SC520_GPWRW, 3);    /* set the GP WR pulse width */
-	write_mmcr_byte(SC520_GPWROFF, 1);  /* set the GP WR offset */
+	sc520_mmcr->gpcsrt = 1;		/* set the GP CS offset */
+	sc520_mmcr->gpcspw = 3;		/* set the GP CS pulse width */
+	sc520_mmcr->gpcsoff = 1;	/* set the GP CS offset */
+	sc520_mmcr->gprdw = 3;		/* set the RD pulse width */
+	sc520_mmcr->gprdoff = 1;	/* set the GP RD offset */
+	sc520_mmcr->gpwrw = 3;		/* set the GP WR pulse width */
+	sc520_mmcr->gpwroff = 1;	/* set the GP WR offset */
 
-	write_mmcr_word(SC520_BOOTCSCTL, 0x0407);		/* set up timing of BOOTCS */
+	sc520_mmcr->bootcsctl = 0x0407;	/* set up timing of BOOTCS */
 
 	/* adjust the memory map:
 	 * by default the first 256MB (0x00000000 - 0x0fffffff) is mapped to SDRAM
@@ -298,17 +299,17 @@ static void bus_init(void)
 
 
 	/* bootcs */
-	write_mmcr_long(SC520_PAR12, 0x8bffe800);
+	sc520_mmcr->par[12] = 0x8bffe800;
 
 	/* IDE0 = GPCS6 1f0-1f7 */
-	write_mmcr_long(SC520_PAR3,  0x380801f0);
+	sc520_mmcr->par[3] = 0x380801f0;
 
 	/* IDE1 = GPCS7 3f6 */
-	write_mmcr_long(SC520_PAR4,  0x3c0003f6);
+	sc520_mmcr->par[4] = 0x3c0003f6;
 
 	asm ("wbinvd\n"); /* Flush cache, req. after setting the unchached attribute ona PAR */
 
-	write_mmcr_byte(SC520_ADDDECCTL, read_mmcr_byte(SC520_ADDDECCTL) & ~(UART2_DIS|UART1_DIS));
+	sc520_mmcr->adddecctl = sc520_mmcr->adddecctl & ~(UART2_DIS|UART1_DIS);
 
 }
 
@@ -361,7 +362,7 @@ u32 isa_map_rom(u32 bus_addr, int size)
 	printf ("setting PAR11 to %x\n", par);
 
 	/* Map rom 0x10000 with PAR1 */
-	write_mmcr_long(SC520_PAR11,  par);
+	sc520_mmcr->par[11] = par;
 
 	return bus_addr;
 }
@@ -373,8 +374,8 @@ u32 isa_map_rom(u32 bus_addr, int size)
 void isa_unmap_rom(u32 addr)
 {
 	printf("isa_unmap_rom asked to unmap %x", addr);
-	if ((addr>>12) == (read_mmcr_long(SC520_PAR11)&0x3ffff)) {
-		write_mmcr_long(SC520_PAR11, 0);
+	if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) {
+		sc520_mmcr->par[11] = 0;
 		printf(" done\n");
 		return;
 	}
@@ -410,7 +411,7 @@ u32 pci_get_rom_window(struct pci_controller *hose, int size)
 	printf ("setting PAR1 to %x\n", par);
 
 	/* Map rom 0x10000 with PAR1 */
-	write_mmcr_long(SC520_PAR1,  par);
+	sc520_mmcr->par[1] = par;
 
 	return PCI_ROM_TEMP_SPACE;
 }
@@ -423,7 +424,7 @@ void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
 {
 	printf("pci_remove_rom_window: %x", addr);
 	if (addr == PCI_ROM_TEMP_SPACE) {
-		write_mmcr_long(SC520_PAR1, 0);
+		sc520_mmcr->par[1] = 0;
 		printf(" done\n");
 		return;
 	}
@@ -441,11 +442,10 @@ void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
 int pci_enable_legacy_video_ports(struct pci_controller *hose)
 {
 	/* Map video memory to 0xa0000*/
-	write_mmcr_long(SC520_PAR0,  0x7200400a);
+	sc520_mmcr->par[0] = 0x7200400a;
 
 	/* forward all I/O accesses to PCI */
-	write_mmcr_byte(SC520_ADDDECCTL,
-			read_mmcr_byte(SC520_ADDDECCTL) | IO_HOLE_DEST_PCI);
+	sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI;
 
 
 	/* so we map away all io ports to pci (only way to access pci io
@@ -455,22 +455,22 @@ int pci_enable_legacy_video_ports(struct pci_controller *hose)
 	 */
 
 	/* bring 0x100 - 0x2f7 back to ISA using PAR5 */
-	write_mmcr_long(SC520_PAR5, 0x31f70100);
+	sc520_mmcr->par[5] = 0x31f70100;
 
 	/* com2 use 2f8-2ff */
 
 	/* bring 0x300 - 0x3af back to ISA using PAR7 */
-	write_mmcr_long(SC520_PAR7, 0x30af0300);
+	sc520_mmcr->par[7] = 0x30af0300;
 
 	/* vga use 3b0-3bb */
 
 	/* bring 0x3bc - 0x3bf back to ISA using PAR8 */
-	write_mmcr_long(SC520_PAR8, 0x300303bc);
+	sc520_mmcr->par[8] = 0x300303bc;
 
 	/* vga use 3c0-3df */
 
 	/* bring 0x3e0 - 0x3f7 back to ISA using PAR9 */
-	write_mmcr_long(SC520_PAR9, 0x301703e0);
+	sc520_mmcr->par[9] = 0x301703e0;
 
 	/* com1 use 3f8-3ff */
 
@@ -489,12 +489,12 @@ int board_init(void)
 	irq_init();
 
 	/* max drive current on SDRAM */
-	write_mmcr_word(SC520_DSCTL, 0x0100);
+	sc520_mmcr->dsctl = 0x0100;
 
 	/* enter debug mode after next reset (only if jumper is also set) */
-	write_mmcr_byte(SC520_RESCFG, 0x08);
+	sc520_mmcr->rescfg = 0x08;
 	/* configure the software timer to 33.000MHz */
-	write_mmcr_byte(SC520_SWTMRCFG, 1);
+	sc520_mmcr->swtmrcfg = 1;
 	gd->bus_clk = 33000000;
 
 	return 0;
@@ -508,17 +508,15 @@ int dram_init(void)
 
 void show_boot_progress(int val)
 {
-	int version = read_mmcr_byte(SC520_SYSINFO);
+	int version = sc520_mmcr->sysinfo;
 
 	if (val < -32) val = -1;  /* let things compatible */
 	if (version == 0) {
 		/* PIO31-PIO16 Data */
-		write_mmcr_word(SC520_PIODATA31_16,
-				(read_mmcr_word(SC520_PIODATA31_16) & 0xffc0)| ((val&0x7e)>>1)); /* 0x1f8 >> 3 */
+		sc520_mmcr->piodata31_16 = (sc520_mmcr->piodata31_16 & 0xffc0) | ((val&0x7e)>>1); /* 0x1f8 >> 3 */
 
 		/* PIO0-PIO15 Data */
-		write_mmcr_word(SC520_PIODATA15_0,
-				(read_mmcr_word(SC520_PIODATA15_0) & 0x1fff)| ((val&0x7)<<13));
+		sc520_mmcr->piodata15_0 = (sc520_mmcr->piodata15_0 & 0x1fff)| ((val&0x7)<<13);
 	} else {
 		/* newer boards use PIO4-PIO12 */
 		/* PIO0-PIO15 Data */
@@ -527,8 +525,7 @@ void show_boot_progress(int val)
 #else
 		val = (val & 0x007) | ((val & 0x07e) << 2);
 #endif
-		write_mmcr_word(SC520_PIODATA15_0,
-				(read_mmcr_word(SC520_PIODATA15_0) & 0xe00f) | ((val&0x01ff)<<4));
+		sc520_mmcr->piodata15_0 = (sc520_mmcr->piodata15_0 & 0xe00f) | ((val&0x01ff)<<4);
 	}
 }
 
@@ -536,7 +533,7 @@ void show_boot_progress(int val)
 int last_stage_init(void)
 {
 
-	int version = read_mmcr_byte(SC520_SYSINFO);
+	int version = sc520_mmcr->sysinfo;
 
 	printf("Omicron Ceti SC520 Spunk revision %x\n", version);
 
@@ -587,30 +584,30 @@ int last_stage_init(void)
 
 void ssi_chip_select(int dev)
 {
-	int version = read_mmcr_byte(SC520_SYSINFO);
+	int version = sc520_mmcr->sysinfo;
 
 	if (version) {
 		/* Spunk board: EEPROM and CAN are actove-low, TEMP and AUX are active high */
 		switch (dev) {
 		case 1: /* EEPROM */
-			write_mmcr_word(SC520_PIOCLR31_16, 0x0004);
+			sc520_mmcr->pioclr31_16 = 0x0004;
 			break;
 
 		case 2: /* Temp Probe */
-			write_mmcr_word(SC520_PIOSET31_16, 0x0002);
+			sc520_mmcr->pioset31_16 = 0x0002;
 			break;
 
 		case 3: /* CAN */
-			write_mmcr_word(SC520_PIOCLR31_16, 0x0008);
+			sc520_mmcr->pioclr31_16 = 0x0008;
 			break;
 
 		case 4: /* AUX */
-			write_mmcr_word(SC520_PIOSET31_16, 0x0001);
+			sc520_mmcr->pioset31_16 = 0x0001;
 			break;
 
 		case 0:
-			write_mmcr_word(SC520_PIOCLR31_16, 0x0003);
-			write_mmcr_word(SC520_PIOSET31_16, 0x000c);
+			sc520_mmcr->pioclr31_16 = 0x0003;
+			sc520_mmcr->pioset31_16 = 0x000c;
 			break;
 
 		default:
@@ -622,15 +619,15 @@ void ssi_chip_select(int dev)
 
 		switch (dev) {
 		case 1: /* EEPROM */
-			write_mmcr_word(SC520_PIOSET15_0, 0x0100);
+			sc520_mmcr->pioset15_0 = 0x0100;
 			break;
 
 		case 2: /* Temp Probe */
-			write_mmcr_word(SC520_PIOSET15_0, 0x0080);
+			sc520_mmcr->pioset15_0 = 0x0080;
 			break;
 
 		case 0:
-			write_mmcr_word(SC520_PIOCLR15_0, 0x0180);
+			sc520_mmcr->pioclr15_0 = 0x0180;
 			break;
 
 		default:
@@ -669,9 +666,7 @@ int mw_eeprom_write(int x, int offset, uchar *buffer, int len)
 
 void spi_init_f(void)
 {
-	read_mmcr_byte(SC520_SYSINFO) ?
-		spi_eeprom_probe(1) :
-	mw_eeprom_probe(1);
+	sc520_mmcr->sysinfo ? spi_eeprom_probe(1) : mw_eeprom_probe(1);
 
 }
 
@@ -686,7 +681,7 @@ ssize_t spi_read(uchar *addr, int alen, uchar *buffer, int len)
 		offset |= addr[i];
 	}
 
-	return	read_mmcr_byte(SC520_SYSINFO) ?
+	return	sc520_mmcr->sysinfo ?
 		spi_eeprom_read(1, offset, buffer, len) :
 	mw_eeprom_read(1, offset, buffer, len);
 }
@@ -702,7 +697,7 @@ ssize_t spi_write(uchar *addr, int alen, uchar *buffer, int len)
 		offset |= addr[i];
 	}
 
-	return	read_mmcr_byte(SC520_SYSINFO) ?
+	return	sc520_mmcr->sysinfo ?
 		spi_eeprom_write(1, offset, buffer, len) :
 	mw_eeprom_write(1, offset, buffer, len);
 }

cpu/i386/sc520/sc520.c

@@ -33,75 +33,35 @@ DECLARE_GLOBAL_DATA_PTR;
 /*
  * utility functions for boards based on the AMD sc520
  *
- * void write_mmcr_byte(u16 mmcr, u8 data)
- * void write_mmcr_word(u16 mmcr, u16 data)
- * void write_mmcr_long(u16 mmcr, u32 data)
- *
- * u8   read_mmcr_byte(u16 mmcr)
- * u16  read_mmcr_word(u16 mmcr)
- * u32  read_mmcr_long(u16 mmcr)
- *
  * void init_sc520(void)
  * unsigned long init_sc520_dram(void)
  */
 
-static u32 mmcr_base= 0xfffef000;
-
-void write_mmcr_byte(u16 mmcr, u8 data)
-{
-	writeb(data, mmcr+mmcr_base);
-}
-
-void write_mmcr_word(u16 mmcr, u16 data)
-{
-	writew(data, mmcr+mmcr_base);
-}
-
-void write_mmcr_long(u16 mmcr, u32 data)
-{
-	writel(data, mmcr+mmcr_base);
-}
-
-u8 read_mmcr_byte(u16 mmcr)
-{
-	return readb(mmcr+mmcr_base);
-}
-
-u16 read_mmcr_word(u16 mmcr)
-{
-	return readw(mmcr+mmcr_base);
-}
-
-u32 read_mmcr_long(u16 mmcr)
-{
-	return readl(mmcr+mmcr_base);
-}
-
+volatile sc520_mmcr_t *sc520_mmcr = (sc520_mmcr_t *)0xfffef000;
 
 void init_sc520(void)
 {
 	/* Set the UARTxCTL register at it's slower,
 	 * baud clock giving us a 1.8432 MHz reference
 	 */
-	write_mmcr_byte(SC520_UART1CTL, 7);
-	write_mmcr_byte(SC520_UART2CTL, 7);
+	sc520_mmcr->uart1ctl = 0x07;
+	sc520_mmcr->uart2ctl = 0x07;
 
 	/* first set the timer pin mapping */
-	write_mmcr_byte(SC520_CLKSEL, 0x72);	/* no clock frequency selected, use 1.1892MHz */
+	sc520_mmcr->clksel = 0x72;	/* no clock frequency selected, use 1.1892MHz */
 
 	/* enable PCI bus arbitrer */
-	write_mmcr_byte(SC520_SYSARBCTL,0x02);  /* enable concurrent mode */
-
-	write_mmcr_word(SC520_SYSARBMENB,0x1f); /* enable external grants */
-	write_mmcr_word(SC520_HBCTL,0x04);      /* enable posted-writes */
+	sc520_mmcr->sysarbctl = 0x02;	/* enable concurrent mode */
 
+	sc520_mmcr->sysarbmenb = 0x1f;	/* enable external grants */
+	sc520_mmcr->hbctl = 0x04;	/* enable posted-writes */
 
 	if (CONFIG_SYS_SC520_HIGH_SPEED) {
-		write_mmcr_byte(SC520_CPUCTL, 0x2);	/* set it to 133 MHz and write back */
+		sc520_mmcr->cpuctl = 0x02;	/* set it to 133 MHz and write back */
 		gd->cpu_clk = 133000000;
 		printf("## CPU Speed set to 133MHz\n");
 	} else {
-		write_mmcr_byte(SC520_CPUCTL, 1);	/* set CPU to 100 MHz and write back cache */
+		sc520_mmcr->cpuctl = 0x01;	/* set it to 100 MHz and write back */
 		printf("## CPU Speed set to 100MHz\n");
 		gd->cpu_clk = 100000000;
 	}
@@ -114,7 +74,7 @@ void init_sc520(void)
 	    "loop 0b\n": : : "ecx");
 
 	/* turn on the SDRAM write buffer */
-	write_mmcr_byte(SC520_DBCTL, 0x11);
+	sc520_mmcr->dbctl = 0x11;
 
 	/* turn on the cache and disable write through */
 	asm("movl	%%cr0, %%eax\n"
@@ -156,10 +116,9 @@ unsigned long init_sc520_dram(void)
 		val = 3;  /* 62.4us */
 	}
 
-	write_mmcr_byte(SC520_DRCCTL, (read_mmcr_byte(SC520_DRCCTL) & 0xcf) | (val<<4));
+	sc520_mmcr->drcctl = (sc520_mmcr->drcctl & 0xcf) | (val<<4);
 
-	val = read_mmcr_byte(SC520_DRCTMCTL);
-	val &= 0xf0;
+	val = sc520_mmcr->drctmctl & 0xf0;
 
 	if (cas_precharge_delay==3) {
 		val |= 0x04;   /* 3T */
@@ -174,12 +133,12 @@ unsigned long init_sc520_dram(void)
 	} else {
 		val |= 1;
 	}
-	write_mmcr_byte(SC520_DRCTMCTL, val);
+	sc520_mmcr->drctmctl = val;
 #endif
 
 	/* We read-back the configuration of the dram
 	 * controller that the assembly code wrote */
-	dram_ctrl = read_mmcr_long(SC520_DRCBENDADR);
+	dram_ctrl = sc520_mmcr->drcbendadr;
 
 	bd->bi_dram[0].start = 0;
 	if (dram_ctrl & 0x80) {
@@ -232,7 +191,7 @@ void reset_cpu(ulong addr)
 {
 	printf("Resetting using SC520 MMCR\n");
 	/* Write a '1' to the SYS_RST of the RESCFG MMCR */
-	write_mmcr_word(SC520_RESCFG, 0x0001);
+	sc520_mmcr->rescfg = 0x01;
 
 	/* NOTREACHED */
 }

cpu/i386/sc520/sc520_pci.c

@@ -33,23 +33,23 @@ static struct {
 	u16 level_reg;
 	u8 level_bit;
 } sc520_irq[] = {
-	{ SC520_IRQ0,  SC520_MPICMODE,  0x01 },
-	{ SC520_IRQ1,  SC520_MPICMODE,  0x02 },
-	{ SC520_IRQ2,  SC520_SL1PICMODE, 0x02 },
-	{ SC520_IRQ3,  SC520_MPICMODE,  0x08 },
-	{ SC520_IRQ4,  SC520_MPICMODE,  0x10 },
-	{ SC520_IRQ5,  SC520_MPICMODE,  0x20 },
-	{ SC520_IRQ6,  SC520_MPICMODE,  0x40 },
-	{ SC520_IRQ7,  SC520_MPICMODE,  0x80 },
-
-	{ SC520_IRQ8,  SC520_SL1PICMODE, 0x01 },
-	{ SC520_IRQ9,  SC520_SL1PICMODE, 0x02 },
-	{ SC520_IRQ10, SC520_SL1PICMODE, 0x04 },
-	{ SC520_IRQ11, SC520_SL1PICMODE, 0x08 },
-	{ SC520_IRQ12, SC520_SL1PICMODE, 0x10 },
-	{ SC520_IRQ13, SC520_SL1PICMODE, 0x20 },
-	{ SC520_IRQ14, SC520_SL1PICMODE, 0x40 },
-	{ SC520_IRQ15, SC520_SL1PICMODE, 0x80 }
+	{ SC520_IRQ0,  0, 0x01 },
+	{ SC520_IRQ1,  0, 0x02 },
+	{ SC520_IRQ2,  1, 0x02 },
+	{ SC520_IRQ3,  0, 0x08 },
+	{ SC520_IRQ4,  0, 0x10 },
+	{ SC520_IRQ5,  0, 0x20 },
+	{ SC520_IRQ6,  0, 0x40 },
+	{ SC520_IRQ7,  0, 0x80 },
+
+	{ SC520_IRQ8,  1, 0x01 },
+	{ SC520_IRQ9,  1, 0x02 },
+	{ SC520_IRQ10, 1, 0x04 },
+	{ SC520_IRQ11, 1, 0x08 },
+	{ SC520_IRQ12, 1, 0x10 },
+	{ SC520_IRQ13, 1, 0x20 },
+	{ SC520_IRQ14, 1, 0x40 },
+	{ SC520_IRQ15, 1, 0x80 }
 };
 
 
@@ -77,34 +77,34 @@ int pci_sc520_set_irq(int pci_pin, int irq)
 
 	/* first disable any non-pci interrupt source that use
 	 * this level */
-	for (i=SC520_GPTMR0MAP;i<=SC520_GP10IMAP;i++) {
-		if (i>=SC520_PCIINTAMAP&&i<=SC520_PCIINTDMAP) {
-			continue;
-		}
-		if (read_mmcr_byte(i) == sc520_irq[irq].priority) {
-			write_mmcr_byte(i, SC520_IRQ_DISABLED);
-		}
+
+	/* PCI interrupt mapping (A through D)*/
+	for (i=0; i<=3 ;i++) {
+		if (sc520_mmcr->pci_int_map[i] == sc520_irq[irq].priority)
+			sc520_mmcr->pci_int_map[i] = SC520_IRQ_DISABLED;
+	}
+
+	/* GP IRQ interrupt mapping */
+	for (i=0; i<=10 ;i++) {
+		if (sc520_mmcr->gp_int_map[i] == sc520_irq[irq].priority)
+			sc520_mmcr->gp_int_map[i] = SC520_IRQ_DISABLED;
 	}
 
 	/* Set the trigger to level */
-	write_mmcr_byte(sc520_irq[irq].level_reg,
-			read_mmcr_byte(sc520_irq[irq].level_reg) | sc520_irq[irq].level_bit);
+	sc520_mmcr->pic_mode[sc520_irq[irq].level_reg] =
+		sc520_mmcr->pic_mode[sc520_irq[irq].level_reg] | sc520_irq[irq].level_bit;
 
 
 	if (pci_pin < 4) {
 		/* PCI INTA-INTD */
 		/* route the interrupt */
-		write_mmcr_byte(SC520_PCIINTAMAP + pci_pin, sc520_irq[irq].priority);
-
-
+		sc520_mmcr->pci_int_map[pci_pin] = sc520_irq[irq].priority;
 	} else {
 		/* GPIRQ0-GPIRQ10 used for additional PCI INTS */
-		write_mmcr_byte(SC520_GP0IMAP + pci_pin - 4, sc520_irq[irq].priority);
+		sc520_mmcr->gp_int_map[pci_pin - 4] = sc520_irq[irq].priority;
 
 		/* also set the polarity in this case */
-		write_mmcr_word(SC520_INTPINPOL,
-				read_mmcr_word(SC520_INTPINPOL) | (1 << (pci_pin-4)));
-
+		sc520_mmcr->intpinpol = sc520_mmcr->intpinpol | (1 << (pci_pin-4));
 	}
 
 	/* register the pin */

cpu/i386/sc520/sc520_ssi.c

@@ -61,32 +61,34 @@ int ssi_set_interface(int freq, int lsb_first, int inv_clock, int inv_phase)
 		temp |= PHS_INV_ENB;
 	}
 
-	write_mmcr_byte(SC520_SSICTL, temp);
+	sc520_mmcr->ssictl = temp;
 
 	return 0;
 }
 
 u8 ssi_txrx_byte(u8 data)
 {
-	write_mmcr_byte(SC520_SSIXMIT, data);
-	while ((read_mmcr_byte(SC520_SSISTA)) & SSISTA_BSY);
-	write_mmcr_byte(SC520_SSICMD, SSICMD_CMD_SEL_XMITRCV);
-	while ((read_mmcr_byte(SC520_SSISTA)) & SSISTA_BSY);
-	return read_mmcr_byte(SC520_SSIRCV);
+	sc520_mmcr->ssixmit = data;
+	while (sc520_mmcr->ssista & SSISTA_BSY);
+	sc520_mmcr->ssicmd = SSICMD_CMD_SEL_XMITRCV;
+	while (sc520_mmcr->ssista & SSISTA_BSY);
+
+	return sc520_mmcr->ssircv;
 }
 
 
 void ssi_tx_byte(u8 data)
 {
-	write_mmcr_byte(SC520_SSIXMIT, data);
-	while ((read_mmcr_byte(SC520_SSISTA)) & SSISTA_BSY);
-	write_mmcr_byte(SC520_SSICMD, SSICMD_CMD_SEL_XMIT);
+	sc520_mmcr->ssixmit = data;
+	while (sc520_mmcr->ssista & SSISTA_BSY);
+	sc520_mmcr->ssicmd = SSICMD_CMD_SEL_XMIT;
 }
 
 u8 ssi_rx_byte(void)
 {
-	while ((read_mmcr_byte(SC520_SSISTA)) & SSISTA_BSY);
-	write_mmcr_byte(SC520_SSICMD, SSICMD_CMD_SEL_RCV);
-	while ((read_mmcr_byte(SC520_SSISTA)) & SSISTA_BSY);
-	return read_mmcr_byte(SC520_SSIRCV);
+	while (sc520_mmcr->ssista & SSISTA_BSY);
+	sc520_mmcr->ssicmd = SSICMD_CMD_SEL_RCV;
+	while (sc520_mmcr->ssista & SSISTA_BSY);
+
+	return sc520_mmcr->ssircv;
 }

cpu/i386/sc520/sc520_timer.c

@@ -30,29 +30,29 @@
 void sc520_timer_isr(void)
 {
 	/* Ack the GP Timer Interrupt */
-	write_mmcr_byte (SC520_GPTMRSTA, 0x02);
+	sc520_mmcr->gptmrsta = 0x02;
 }
 
 int timer_init(void)
 {
 	/* Map GP Timer 1 to Master PIC IR0  */
-	write_mmcr_byte (SC520_GPTMR1MAP, 0x01);
+	sc520_mmcr->gp_tmr_int_map[1] = 0x01;
 
 	/* Disable GP Timers 1 & 2 - Allow configuration writes */
-	write_mmcr_word (SC520_GPTMR1CTL, 0x4000);
-	write_mmcr_word (SC520_GPTMR2CTL, 0x4000);
+	sc520_mmcr->gptmr1ctl = 0x4000;
+	sc520_mmcr->gptmr2ctl = 0x4000;
 
 	/* Reset GP Timers 1 & 2 */
-	write_mmcr_word (SC520_GPTMR1CNT, 0x0000);
-	write_mmcr_word (SC520_GPTMR2CNT, 0x0000);
+	sc520_mmcr->gptmr1cnt = 0x0000;
+	sc520_mmcr->gptmr2cnt = 0x0000;
 
 	/* Setup GP Timer 2 as a 100kHz (10us) prescaler */
-	write_mmcr_word (SC520_GPTMR2MAXCMPA, 83);
-	write_mmcr_word (SC520_GPTMR2CTL, 0xc001);
+	sc520_mmcr->gptmr2maxcmpa = 83;
+	sc520_mmcr->gptmr2ctl = 0xc001;
 
 	/* Setup GP Timer 1 as a 1000 Hz (1ms) interrupt generator */
-	write_mmcr_word (SC520_GPTMR1MAXCMPA, 100);
-	write_mmcr_word (SC520_GPTMR1CTL, 0xe009);
+	sc520_mmcr->gptmr1maxcmpa = 100;
+	sc520_mmcr->gptmr1ctl = 0xe009;
 
 	/* Register the SC520 specific timer interrupt handler */
 	register_timer_isr (sc520_timer_isr);
@@ -62,7 +62,7 @@ int timer_init(void)
 	unmask_irq (0);
 
 	/* Clear the GP Timer 1 status register to get the show rolling*/
-	write_mmcr_byte (SC520_GPTMRSTA, 0x02);
+	sc520_mmcr->gptmrsta = 0x02;
 
 	return 0;
 }
@@ -71,12 +71,13 @@ void udelay(unsigned long usec)
 {
 	int m = 0;
 	long u;
+	long temp;
 
-	read_mmcr_word (SC520_SWTMRMILLI);
-	read_mmcr_word (SC520_SWTMRMICRO);
+	temp = sc520_mmcr->swtmrmilli;
+	temp = sc520_mmcr->swtmrmicro;
 
 	do {
-		m += read_mmcr_word (SC520_SWTMRMILLI);
-		u = read_mmcr_word (SC520_SWTMRMICRO) + (m * 1000);
+		m += sc520_mmcr->swtmrmilli;
+		u = sc520_mmcr->swtmrmicro + (m * 1000);
 	} while (u < usec);
 }

include/asm-i386/ic/sc520.h

@@ -24,179 +24,243 @@
 #ifndef _ASM_IC_SC520_H_
 #define _ASM_IC_SC520_H_ 1
 
-/* Memory mapped configuration registers, MMCR */
-#define SC520_REVID		0x0000	/* ElanSC520 Microcontroller Revision ID Register */
-#define SC520_CPUCTL		0x0002	/* Am5x86 CPU Control Register */
-#define SC520_DRCCTL		0x0010	/* SDRAM Control Register */
-#define SC520_DRCTMCTL		0x0012	/* SDRAM Timing Control Register */
-#define SC520_DRCCFG		0x0014	/* SDRAM Bank Configuration Register*/
-#define SC520_DRCBENDADR	0x0018	/* SDRAM Bank 0-3 Ending Address Register*/
-#define SC520_ECCCTL		0x0020	/* ECC Control Register */
-#define SC520_ECCSTA		0x0021	/* ECC Status Register */
-#define SC520_ECCCKBPOS		0x0022	/* ECC Check Bit Position Register */
-#define SC520_ECCSBADD		0x0024	/* ECC Single-Bit Error Address Register */
+#ifndef __ASSEMBLY__
+
+void init_sc520(void);
+unsigned long init_sc520_dram(void);
+
+/* Memory mapped configuration registers */
+typedef struct sc520_mmcr {
+	u16 revid;	/* ElanSC520 microcontroller revision id */
+	u8  cpuctl;	/* am5x86 CPU control  */
+
+	u8  pad_0x003[0x0d];
+
+	u8  drcctl;		/* SDRAM control */
+	u8  pad_0x011[0x01];
+	u8  drctmctl;		/* SDRAM timing control */
+	u8  pad_0x013[0x01];
+	u16 drccfg;		/* SDRAM bank configuration*/
+	u8  pad_0x016[0x02];
+	u32 drcbendadr;		/* SDRAM bank 0-3 ending address*/
+	u8  pad_0x01c[0x04];
+	u8  eccctl;		/* ECC control */
+	u8  eccsta;		/* ECC status */
+	u8  eccckbpos;		/* ECC check bit position */
+	u8  ecccktest;		/* ECC Check Code Test */
+	u32 eccsbadd;		/* ECC single-bit error address */
+	u32 eccmbadd;		/* ECC multi-bit error address */
+
+	u8  pad_0x02c[0x14];
+
+	u8  dbctl;		/* SDRAM buffer control */
+
+	u8  pad_0x041[0x0f];
+
+	u16 bootcsctl;		/* /BOOTCS control */
+	u8  pad_0x052[0x02];
+	u16 romcs1ctl;		/* /ROMCS1 control */
+	u16 romcs2ctl;		/* /ROMCS2 control */
+
+	u8  pad_0x058[0x08];
+
+	u16 hbctl;		/* host bridge control */
+	u16 hbtgtirqctl;	/* host bridge target interrupt control */
+	u16 hbtgtirqsta;	/* host bridge target interrupt status */
+	u16 hbmstirqctl;	/* host bridge target interrupt control */
+	u16 hbmstirqsta;	/* host bridge master interrupt status */
+	u8  pad_0x06a[0x02];
+	u32 mstintadd;		/* host bridge master interrupt address */
+
+	u8  sysarbctl;		/* system arbiter control */
+	u8  pciarbsta;		/* PCI bus arbiter status */
+	u16 sysarbmenb;		/* system arbiter master enable */
+	u32 arbprictl;		/* arbiter priority control */
+
+	u8  pad_0x078[0x08];
+
+	u8  adddecctl;		/* address decode control */
+	u8  pad_0x081[0x01];
+	u16 wpvsta;		/* write-protect violation status */
+	u8  pad_0x084[0x04];
+	u32 par[16];		/* programmable address regions */
+
+	u8  pad_0x0c8[0x0b38];
+
+	u8  gpecho;		/* GP echo mode */
+	u8  gpcsdw;		/* GP chip select data width */
+	u16 gpcsqual;		/* GP chip select qualification */
+	u8  pad_0xc04[0x4];
+	u8  gpcsrt;		/* GP chip select recovery time */
+	u8  gpcspw;		/* GP chip select pulse width */
+	u8  gpcsoff;		/* GP chip select offset */
+	u8  gprdw;		/* GP read pulse width */
+	u8  gprdoff;		/* GP read offset */
+	u8  gpwrw;		/* GP write pulse width */
+	u8  gpwroff;		/* GP write offset */
+	u8  gpalew;		/* GP ale pulse width */
+	u8  gpaleoff;		/* GP ale offset */
+
+	u8  pad_0xc11[0x0f];
+
+	u16 piopfs15_0;		/* PIO15-PIO0 pin function select */
+	u16 piopfs31_16;	/* PIO31-PIO16 pin function select */
+	u8  cspfs;		/* chip select pin function select */
+	u8  pad_0xc25[0x01];
+	u8  clksel;		/* clock select */
+	u8  pad_0xc27[0x01];
+	u16 dsctl;		/* drive strength control */
+	u16 piodir15_0;		/* PIO15-PIO0 direction */
+	u16 piodir31_16;	/* PIO31-PIO16 direction */
+	u8  pad_0xc2e[0x02];
+	u16 piodata15_0	;	/* PIO15-PIO0 data */
+	u16 piodata31_16;	/* PIO31-PIO16 data */
+	u16 pioset15_0;		/* PIO15-PIO0 set */
+	u16 pioset31_16;	/* PIO31-PIO16 set */
+	u16 pioclr15_0;		/* PIO15-PIO0 clear */
+	u16 pioclr31_16;	/* PIO31-PIO16 clear */
+
+	u8  pad_0xc3c[0x24];
+
+	u16 swtmrmilli;		/* software timer millisecond count */
+	u16 swtmrmicro;		/* software timer microsecond count */
+	u8  swtmrcfg;		/* software timer configuration */
+
+	u8  pad_0xc65[0x0b];
+
+	u8  gptmrsta;		/* GP timers status register */
+	u8  pad_0xc71;
+	u16 gptmr0ctl;		/* GP timer 0 mode/control */
+	u16 gptmr0cnt;		/* GP timer 0 count */
+	u16 gptmr0maxcmpa;	/* GP timer 0 maxcount compare A */
+	u16 gptmr0maxcmpb;	/* GP timer 0 maxcount compare B */
+	u16 gptmr1ctl;		/* GP timer 1 mode/control */
+	u16 gptmr1cnt;		/* GP timer 1 count */
+	u16 gptmr1maxcmpa;	/* GP timer 1 maxcount compare A */
+	u16 gptmr1maxcmpb;	/* GP timer 1 maxcount compare B*/
+	u16 gptmr2ctl;		/* GP timer 2 mode/control */
+	u16 gptmr2cnt;		/* GP timer 2 count */
+	u8  pad_0xc86[0x08];
+	u16 gptmr2maxcmpa;	/* GP timer 2 maxcount compare A */
+
+	u8  pad_0xc90[0x20];
+
+	u16 wdtmrctl;		/* watchdog timer control */
+	u16 wdtmrcntl;		/* watchdog timer count low */
+	u16 wdtmrcnth;		/* watchdog timer count high */
+
+	u8  pad_0xcb6[0x0a];
+
+	u8  uart1ctl;		/* UART 1 general control */
+	u8  uart1sta;		/* UART 1 general status */
+	u8  uart1fcrshad;	/* UART 1 FIFO control shadow */
+	u8  pad_0xcc3[0x01];
+	u8  uart2ctl;		/* UART 2 general control */
+	u8  uart2sta;		/* UART 2 general status */
+	u8  uart2fcrshad;	/* UART 2 FIFO control shadow */
+
+	u8  pad_0xcc7[0x09];
+
+	u8  ssictl;		/* SSI control */
+	u8  ssixmit;		/* SSI transmit */
+	u8  ssicmd;		/* SSI command */
+	u8  ssista;		/* SSI status */
+	u8  ssircv;		/* SSI receive */
+
+	u8  pad_0xcd5[0x2b];
+
+	u8  picicr;		/* interrupt control */
+	u8  pad_0xd01[0x01];
+	u8  pic_mode[3];	/* PIC interrupt mode */
+	u8  pad_0xd05[0x03];
+	u16 swint16_1;		/* software interrupt 16-1 control */
+	u8  swint22_17;		/* software interrupt 22-17/NMI control */
+	u8  pad_0xd0b[0x05];
+	u16 intpinpol;		/* interrupt pin polarity */
+	u8  pad_0xd12[0x02];
+	u16 pcihostmap;		/* PCI host bridge interrupt mapping */
+	u8  pad_0xd16[0x02];
+	u16 eccmap;		/* ECC interrupt mapping */
+	u8  gp_tmr_int_map[3];	/* GP timer interrupt mapping */
+	u8  pad_0xd1d[0x03];
+	u8  pit_int_map[3];	/* PIT interrupt mapping */
+	u8  pad_0xd23[0x05];
+	u8  uart_int_map[2];	/* UART interrupt mapping */
+	u8  pad_0xd2a[0x06];
+	u8  pci_int_map[4];	/* PCI interrupt mapping (A through D)*/
+	u8  pad_0xd34[0x0c];
+	u8  dmabcintmap;	/* DMA buffer chaining interrupt mapping */
+	u8  ssimap;		/* SSI interrupt mapping register */
+	u8  wdtmap;		/* watchdog timer interrupt mapping */
+	u8  rtcmap;		/* RTC interrupt mapping register */
+	u8  wpvmap;		/* write-protect interrupt mapping */
+	u8  icemap;		/* AMDebug JTAG Rx/Tx interrupt mapping */
+	u8  ferrmap;		/* floating point error interrupt mapping */
+	u8  pad_0xd47[0x09];
+	u8  gp_int_map[11];	/* GP IRQ interrupt mapping */
+
+	u8  pad_0xd5b[0x15];
+
+	u8  sysinfo;		/* system board information */
+	u8  pad_0xd71[0x01];
+	u8  rescfg;		/* reset configuration */
+	u8  pad_0xd73[0x01];
+	u8  ressta;		/* reset status */
+
+	u8  pad_0xd75[0x0b];
+
+	u8  gpdmactl;		/* GP-DMA Control */
+	u8  gpdmammio;		/* GP-DMA memory-mapped I/O */
+	u16 gpdmaextchmapa;	/* GP-DMA resource channel map a */
+	u16 gpdmaextchmapb;	/* GP-DMA resource channel map b */
+	u8  gp_dma_ext_pg_0;	/* GP-DMA channel extended page 0 */
+	u8  gp_dma_ext_pg_1;	/* GP-DMA channel extended page 0 */
+	u8  gp_dma_ext_pg_2;	/* GP-DMA channel extended page 0 */
+	u8  gp_dma_ext_pg_3;	/* GP-DMA channel extended page 0 */
+	u8  gp_dma_ext_pg_5;	/* GP-DMA channel extended page 0 */
+	u8  gp_dma_ext_pg_6;	/* GP-DMA channel extended page 0 */
+	u8  gp_dma_ext_pg_7;	/* GP-DMA channel extended page 0 */
+	u8  pad_0xd8d[0x03];
+	u8  gpdmaexttc3;	/* GP-DMA channel 3 extender transfer count */
+	u8  gpdmaexttc5;	/* GP-DMA channel 5 extender transfer count */
+	u8  gpdmaexttc6;	/* GP-DMA channel 6 extender transfer count */
+	u8  gpdmaexttc7;	/* GP-DMA channel 7 extender transfer count */
+	u8  pad_0xd94[0x4];
+	u8  gpdmabcctl;		/* buffer chaining control */
+	u8  gpdmabcsta;		/* buffer chaining status */
+	u8  gpdmabsintenb;	/* buffer chaining interrupt enable */
+	u8  gpdmabcval;		/* buffer chaining valid */
+	u8  pad_0xd9c[0x04];
+	u16 gpdmanxtaddl3;	/* GP-DMA channel 3 next address low */
+	u16 gpdmanxtaddh3;	/* GP-DMA channel 3 next address high */
+	u16 gpdmanxtaddl5;	/* GP-DMA channel 5 next address low */
+	u16 gpdmanxtaddh5;	/* GP-DMA channel 5 next address high */
+	u16 gpdmanxtaddl6;	/* GP-DMA channel 6 next address low */
+	u16 gpdmanxtaddh6;	/* GP-DMA channel 6 next address high */
+	u16 gpdmanxtaddl7;	/* GP-DMA channel 7 next address low */
+	u16 gpdmanxtaddh7;	/* GP-DMA channel 7 next address high */
+	u16 gpdmanxttcl3;	/* GP-DMA channel 3 next transfer count low */
+	u16 gpdmanxttch3;	/* GP-DMA channel 3 next transfer count high */
+	u16 gpdmanxttcl5;	/* GP-DMA channel 5 next transfer count low */
+	u16 gpdmanxttch5;	/* GP-DMA channel 5 next transfer count high */
+	u16 gpdmanxttcl6;	/* GP-DMA channel 6 next transfer count low */
+	u16 gpdmanxttch6;	/* GP-DMA channel 6 next transfer count high */
+	u16 gpdmanxttcl7;	/* GP-DMA channel 7 next transfer count low */
+	u16 gpdmanxttch7;	/* GP-DMA channel 7 next transfer count high */
+
+	u8  pad_0xdc0[0x0240];
+} sc520_mmcr_t;
+
+extern volatile sc520_mmcr_t *sc520_mmcr;
+
+#endif
+
+/* MMCR Offsets (required for assembler code */
 #define SC520_DBCTL		0x0040	/* SDRAM Buffer Control Register */
-#define SC520_BOOTCSCTL		0x0050	/* /BOOTCS Control Register */
-#define SC520_ROMCS1CTL		0x0054	/* /ROMCS1 Control Register */
-#define SC520_ROMCS2CTL		0x0056	/* /ROMCS2 Control Register */
-#define SC520_HBCTL		0x0060	/* Host Bridge Control Register */
-#define SC520_HBTGTIRQCTL	0x0062	/* Host Bridge Target Interrupt Control Register */
-#define SC520_HBTGTIRQSTA	0x0064	/* Host Bridge Target Interrupt Status Register */
-#define SC520_HBMSTIRQCTL	0x0066	/* Host Bridge Target Interrupt Control Register */
-#define SC520_HBMSTIRQSTA	0x0068	/* Host Bridge Master Interrupt Status Register */
-#define SC520_MSTINTADD		0x006c	/* Host Bridge Master Interrupt Address Register */
-#define SC520_SYSARBCTL		0x0070	/* System Arbiter Control Register */
-#define SC520_PCIARBSTA		0x0071	/* PCI Bus Arbiter Status Register */
-#define SC520_SYSARBMENB	0x0072	/* System Arbiter Master Enable Register */
-#define SC520_ARBPRICTL		0x0074	/* Arbiter Priority Control Register */
-#define SC520_ADDDECCTL		0x0080	/* Address Decode Control Register */
-#define SC520_WPVSTA		0x0082	/* Write-Protect Violation Status Register */
-#define SC520_PAR0		0x0088	/* Programmable Address Region 0 Register */
-#define SC520_PAR1		0x008c	/* Programmable Address Region 1 Register */
-#define SC520_PAR2		0x0090	/* Programmable Address Region 2 Register */
-#define SC520_PAR3		0x0094	/* Programmable Address Region 3 Register */
-#define SC520_PAR4		0x0098	/* Programmable Address Region 4 Register */
-#define SC520_PAR5		0x009c	/* Programmable Address Region 5 Register */
-#define SC520_PAR6		0x00a0	/* Programmable Address Region 6 Register */
-#define SC520_PAR7		0x00a4	/* Programmable Address Region 7 Register */
-#define SC520_PAR8		0x00a8	/* Programmable Address Region 8 Register */
-#define SC520_PAR9		0x00ac	/* Programmable Address Region 9 Register */
-#define SC520_PAR10		0x00b0	/* Programmable Address Region 10 Register */
-#define SC520_PAR11		0x00b4	/* Programmable Address Region 11 Register */
-#define SC520_PAR12		0x00b8	/* Programmable Address Region 12 Register */
-#define SC520_PAR13		0x00bc	/* Programmable Address Region 13 Register */
 #define SC520_PAR14		0x00c0	/* Programmable Address Region 14 Register */
 #define SC520_PAR15		0x00c4	/* Programmable Address Region 15 Register */
-#define SC520_GPECHO		0x0c00	/* GP Echo Mode Register */
-#define SC520_GPCSDW		0x0c01	/* GP Chip Select Data Width Register */
-#define SC520_GPCSQUAL		0x0c02	/* GP Chip Select Qualification Register */
-#define SC520_GPCSRT		0x0c08	/* GP Chip Select Recovery Time Register */
-#define SC520_GPCSPW		0x0c09	/* GP Chip Select Pulse Width Register */
-#define SC520_GPCSOFF		0x0c0a	/* GP Chip Select Offset Register */
-#define SC520_GPRDW		0x0c0b	/* GP Read Pulse Width Register */
-#define SC520_GPRDOFF		0x0c0c	/* GP Read Offset Register */
-#define SC520_GPWRW		0x0c0d	/* GP Write Pulse Width Register */
-#define SC520_GPWROFF		0x0c0e	/* GP Write Offset Register */
-#define SC520_GPALEW		0x0c0f	/* GP ALE Pulse Width Register */
-#define SC520_GPALEOFF		0x0c10	/* GP ALE Offset Register */
-#define SC520_PIOPFS15_0	0x0c20	/* PIO15-PIO0 Pin Function Select */
-#define SC520_PIOPFS31_16	0x0c22	/* PIO31-PIO16 Pin Function Select */
-#define SC520_CSPFS		0x0c24	/* Chip Select Pin Function Select */
-#define SC520_CLKSEL		0x0c26	/* Clock Select */
-#define SC520_DSCTL		0x0c28	/* Drive Strength Control */
-#define SC520_PIODIR15_0	0x0c2a	/* PIO15-PIO0 Direction */
-#define SC520_PIODIR31_16	0x0c2c	/* PIO31-PIO16 Direction */
-#define SC520_PIODATA15_0	0x0c30	/* PIO15-PIO0 Data */
-#define SC520_PIODATA31_16	0x0c32	/* PIO31-PIO16 Data */
-#define SC520_PIOSET15_0	0x0c34	/* PIO15-PIO0 Set */
-#define SC520_PIOSET31_16	0x0c36	/* PIO31-PIO16 Set */
-#define SC520_PIOCLR15_0	0x0c38	/* PIO15-PIO0 Clear */
-#define SC520_PIOCLR31_16	0x0c3a	/* PIO31-PIO16 Clear */
-#define SC520_SWTMRMILLI	0x0c60	/* Software Timer Millisecond Count */
-#define SC520_SWTMRMICRO	0x0c62	/* Software Timer Microsecond Count */
-#define SC520_SWTMRCFG		0x0c64	/* Software Timer Configuration */
-#define SC520_GPTMRSTA		0x0c70	/* GP Timers Status Register */
-#define SC520_GPTMR0CTL		0x0c72	/* GP Timer 0 Mode/Control Register */
-#define SC520_GPTMR0CNT		0x0c74	/* GP Timer 0 Count Register */
-#define SC520_GPTMR0MAXCMPA	0x0c76	/* GP Timer 0 Maxcount Compare A Register */
-#define SC520_GPTMR0MAXCMPB	0x0c78	/* GP Timer 0 Maxcount Compare B Register */
-#define SC520_GPTMR1CTL		0x0c7a	/* GP Timer 1 Mode/Control Register */
-#define SC520_GPTMR1CNT		0x0c7c	/* GP Timer 1 Count Register */
-#define SC520_GPTMR1MAXCMPA	0x0c7e	/* GP Timer 1 Maxcount Compare Register A */
-#define SC520_GPTMR1MAXCMPB	0x0c80	/* GP Timer 1 Maxcount Compare B Register */
-#define SC520_GPTMR2CTL		0x0c82	/* GP Timer 2 Mode/Control Register */
-#define SC520_GPTMR2CNT		0x0c84	/* GP Timer 2 Count Register */
-#define SC520_GPTMR2MAXCMPA	0x0c8e	/* GP Timer 2 Maxcount Compare A Register */
-#define SC520_WDTMRCTL		0x0cb0	/* Watchdog Timer Control Register */
-#define SC520_WDTMRCNTL		0x0cb2	/* Watchdog Timer Count Low Register */
-#define SC520_WDTMRCNTH		0x0cb4	/* Watchdog Timer Count High Register */
-#define SC520_UART1CTL		0x0cc0	/* UART 1 General Control Register */
-#define SC520_UART1STA		0x0cc1	/* UART 1 General Status Register */
-#define SC520_UART1FCRSHAD	0x0cc2	/* UART 1 FIFO Control Shadow Register */
-#define SC520_UART2CTL		0x0cc4	/* UART 2 General Control Register */
-#define SC520_UART2STA		0x0cc5	/* UART 2 General Status Register */
-#define SC520_UART2FCRSHAD	0x0cc6	/* UART 2 FIFO Control Shadow Register */
-#define SC520_SSICTL		0x0cd0	/* SSI Control */
-#define SC520_SSIXMIT		0x0cd1	/* SSI Transmit */
-#define SC520_SSICMD		0x0cd2	/* SSI Command */
-#define SC520_SSISTA		0x0cd3	/* SSI Status */
-#define SC520_SSIRCV		0x0cd4	/* SSI Receive */
-#define SC520_PICICR		0x0d00	/* Interrupt Control Register */
-#define SC520_MPICMODE		0x0d02	/* Master PIC Interrupt Mode Register */
-#define SC520_SL1PICMODE	0x0d03	/* Slave 1 PIC Interrupt Mode Register */
-#define SC520_SL2PICMODE	0x0d04	/* Slave 2 PIC Interrupt Mode Register */
-#define SC520_SWINT16_1		0x0d08	/* Software Interrupt 16-1 Control Register */
-#define SC520_SWINT22_17	0x0d0a	/* Software Interrupt 22-17/NMI Control Register */
-#define SC520_INTPINPOL		0x0d10	/* Interrupt Pin Polarity Register */
-#define SC520_PCIHOSTMAP	0x0d14	/* PCI Host Bridge Interrupt Mappin Register */
-#define SC520_ECCMAP		0x0d18	/* ECC Interrupt Mapping Register */
-#define SC520_GPTMR0MAP		0x0d1a	/* GP Timer 0 Interrupt Mapping Register */
-#define SC520_GPTMR1MAP		0x0d1b	/* GP Timer 1 Interrupt Mapping Register */
-#define SC520_GPTMR2MAP		0x0d1c	/* GP Timer 2 Interrupt Mapping Register */
-#define SC520_PIT0MAP		0x0d20	/* PIT0 Interrupt Mapping Register */
-#define SC520_PIT1MAP		0x0d21	/* PIT1 Interrupt Mapping Register */
-#define SC520_PIT2MAP		0x0d22	/* PIT2 Interrupt Mapping Register */
-#define SC520_UART1MAP		0x0d28	/* UART 1 Interrupt Mapping Register */
-#define SC520_UART2MAP		0x0d29	/* UART 2 Interrupt Mapping Register */
-#define SC520_PCIINTAMAP	0x0d30	/* PCI Interrupt A Mapping Register */
-#define SC520_PCIINTBMAP	0x0d31	/* PCI Interrupt B Mapping Register */
-#define SC520_PCIINTCMAP	0x0d32	/* PCI Interrupt C Mapping Register */
-#define SC520_PCIINTDMAP	0x0d33	/* PCI Interrupt D Mapping Register */
-#define SC520_DMABCINTMAP	0x0d40	/* DMA Buffer Chaining Interrupt Mapping Register */
-#define SC520_SSIMAP		0x0d41	/* SSI Interrupt Mapping Register */
-#define SC520_WDTMAP		0x0d42	/* Watchdog Timer Interrupt Mapping Register */
-#define SC520_RTCMAP		0x0d43	/* RTC Interrupt Mapping Register */
-#define SC520_WPVMAP		0x0d44	/* Write-Protect Interrupt Mapping Register */
-#define SC520_ICEMAP		0x0d45	/* AMDebug JTAG RX/TX Interrupt Mapping Register */
-#define SC520_FERRMAP		0x0d46	/* Floating Point Error Interrupt Mapping Register */
-#define SC520_GP0IMAP		0x0d50	/* GPIRQ0 Interrupt Mapping Register */
-#define SC520_GP1IMAP		0x0d51	/* GPIRQ1 Interrupt Mapping Register */
-#define SC520_GP2IMAP		0x0d52	/* GPIRQ2 Interrupt Mapping Register */
-#define SC520_GP3IMAP		0x0d53	/* GPIRQ3 Interrupt Mapping Register */
-#define SC520_GP4IMAP		0x0d54	/* GPIRQ4 Interrupt Mapping Register */
-#define SC520_GP5IMAP		0x0d55	/* GPIRQ5 Interrupt Mapping Register */
-#define SC520_GP6IMAP		0x0d56	/* GPIRQ6 Interrupt Mapping Register */
-#define SC520_GP7IMAP		0x0d57	/* GPIRQ7 Interrupt Mapping Register */
-#define SC520_GP8IMAP		0x0d58	/* GPIRQ8 Interrupt Mapping Register */
-#define SC520_GP9IMAP		0x0d59	/* GPIRQ9 Interrupt Mapping Register */
-#define SC520_GP10IMAP		0x0d5a	/* GPIRQ10 Interrupt Mapping Register */
-#define SC520_SYSINFO		0x0d70	/* System Board Information Register */
-#define SC520_RESCFG		0x0d72	/* Reset Configuration Register */
-#define SC520_RESSTA		0x0d74	/* Reset Status Register */
-#define SC520_GPDMAMMIO		0x0d81	/* GP-DMA Memory-Mapped I/O Register */
-#define SC520_GPDMAEXTCHMAPA	0x0d82	/* GP-DMA Resource Channel Map A */
-#define SC520_GPDMAEXTCHMAPB	0x0d84	/* GP-DMA Resource Channel Map B */
-#define SC520_GPDMAEXTPG0	0x0d86	/* GP-DMA Channel 0 Extended Page */
-#define SC520_GPDMAEXTPG1	0x0d87	/* GP-DMA Channel 1 Extended Page */
-#define SC520_GPDMAEXTPG2	0x0d88	/* GP-DMA Channel 2 Extended Page */
-#define SC520_GPDMAEXTPG3	0x0d89	/* GP-DMA Channel 3 Extended Page */
-#define SC520_GPDMAEXTPG5	0x0d8a	/* GP-DMA Channel 5 Extended Page */
-#define SC520_GPDMAEXTPG6	0x0d8b	/* GP-DMA Channel 6 Extended Page */
-#define SC520_GPDMAEXTPG7	0x0d8c	/* GP-DMA Channel 7 Extended Page */
-#define SC520_GPDMAEXTTC3	0x0d90	/* GP-DMA Channel 3 Extender Transfer count */
-#define SC520_GPDMAEXTTC5	0x0d91	/* GP-DMA Channel 5 Extender Transfer count */
-#define SC520_GPDMAEXTTC6	0x0d92	/* GP-DMA Channel 6 Extender Transfer count */
-#define SC520_GPDMAEXTTC7	0x0d93	/* GP-DMA Channel 7 Extender Transfer count */
-#define SC520_GPDMABCCTL	0x0d98	/* Buffer Chaining Control */
-#define SC520_GPDMABCSTA	0x0d99	/* Buffer Chaining Status */
-#define SC520_GPDMABSINTENB	0x0d9a	/* Buffer Chaining Interrupt Enable */
-#define SC520_GPDMABCVAL	0x0d9b	/* Buffer Chaining Valid */
-#define SC520_GPDMANXTADDL3	0x0da0	/* GP-DMA Channel 3 Next Address Low */
-#define SC520_GPDMANXTADDH3	0x0da2	/* GP-DMA Channel 3 Next Address High */
-#define SC520_GPDMANXTADDL5	0x0da4	/* GP-DMA Channel 5 Next Address Low */
-#define SC520_GPDMANXTADDH5	0x0da6	/* GP-DMA Channel 5 Next Address High */
-#define SC520_GPDMANXTADDL6	0x0da8	/* GP-DMA Channel 6 Next Address Low */
-#define SC520_GPDMANXTADDH6	0x0daa	/* GP-DMA Channel 6 Next Address High */
-#define SC520_GPDMANXTADDL7	0x0dac	/* GP-DMA Channel 7 Next Address Low */
-#define SC520_GPDMANXTADDH7	0x0dae	/* GP-DMA Channel 7 Next Address High */
-#define SC520_GPDMANXTTCL3	0x0db0	/* GP-DMA Channel 3 Next Transfer Count Low */
-#define SC520_GPDMANXTTCH3	0x0db2	/* GP-DMA Channel 3 Next Transfer Count High */
-#define SC520_GPDMANXTTCL5	0x0db4	/* GP-DMA Channel 5 Next Transfer Count Low */
-#define SC520_GPDMANXTTCH5	0x0db6	/* GP-DMA Channel 5 Next Transfer Count High */
-#define SC520_GPDMANXTTCL6	0x0db8	/* GP-DMA Channel 6 Next Transfer Count Low */
-#define SC520_GPDMANXTTCH6	0x0dba	/* GP-DMA Channel 6 Next Transfer Count High */
-#define SC520_GPDMANXTTCL7	0x0dbc	/* GP-DMA Channel 7 Next Transfer Count Low */
-#define SC520_GPDMANXTTCH7	0x0dbe	/* GP-DMA Channel 7 Next Transfer Count High */
+#define SC520_SWTMRMILLI	0x0c60  /* Software Timer Millisecond Count */
+#define SC520_SWTMRMICRO	0x0c62  /* Software Timer Microsecond Count */
 
 /* MMCR Register bits (not all of them :) ) */
 
@@ -221,7 +285,6 @@
 #define SSISTA_BSY		0x02	/* SSI Busy */
 #define SSISTA_TC_INT		0x01	/* SSI Transaction Complete Interrupt */
 
-
 /* BITS for SC520_ADDDECCTL: */
 #define WPV_INT_ENB		0x80	/* Write-Protect Violation Interrupt Enable */
 #define IO_HOLE_DEST_PCI	0x10	/* I/O Hole Access Destination */
@@ -233,7 +296,6 @@
 #define SC520_REG_ADDR		0x00000cf8
 #define SC520_REG_DATA		0x00000cfc
 
-
 #define SC520_ISA_MEM_PHYS	0x00000000
 #define SC520_ISA_MEM_BUS	0x00000000
 #define SC520_ISA_MEM_SIZE	0x01000000
@@ -282,15 +344,4 @@
 #define SC520_IRQ14 9
 #define SC520_IRQ15 10
 
-/* utility functions */
-void write_mmcr_byte(u16 mmcr, u8 data);
-void write_mmcr_word(u16 mmcr, u16 data);
-void write_mmcr_long(u16 mmcr, u32 data);
-u8 read_mmcr_byte(u16 mmcr);
-u16 read_mmcr_word(u16 mmcr);
-u32 read_mmcr_long(u16 mmcr);
-
-void init_sc520(void);
-unsigned long init_sc520_dram(void);
-
 #endif