Merge branch 'master' of git://git.denx.de/u-boot-mpc86xx

Makefile

@@ -2459,8 +2459,14 @@ TQM8560_config:		unconfig
 MPC8610HPCD_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc86xx mpc8610hpcd freescale
 
+MPC8641HPCN_36BIT_config \
 MPC8641HPCN_config:    unconfig
-	@$(MKCONFIG) $(@:_config=) ppc mpc86xx mpc8641hpcn freescale
+	@mkdir -p $(obj)include
+	@if [ "$(findstring _36BIT_,$@)" ] ; then \
+		echo "#define CONFIG_PHYS_64BIT" >>$(obj)include/config.h ; \
+		$(XECHO) "... enabling 36-bit physical addressing." ; \
+	fi
+	@$(MKCONFIG) -a MPC8641HPCN ppc mpc86xx mpc8641hpcn freescale
 
 sbc8641d_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc86xx sbc8641d

board/freescale/mpc8610hpcd/mpc8610hpcd.c

@@ -37,7 +37,7 @@
 #include "../common/pixis.h"
 
 void sdram_init(void);
-long int fixed_sdram(void);
+phys_size_t fixed_sdram(void);
 void mpc8610hpcd_diu_init(void);
 
 
@@ -117,7 +117,7 @@ int checkboard(void)
 phys_size_t
 initdram(int board_type)
 {
-	long dram_size = 0;
+	phys_size_t dram_size = 0;
 
 #if defined(CONFIG_SPD_EEPROM)
 	dram_size = fsl_ddr_sdram();
@@ -140,7 +140,7 @@ initdram(int board_type)
  * Fixed sdram init -- doesn't use serial presence detect.
  */
 
-long int fixed_sdram(void)
+phys_size_t fixed_sdram(void)
 {
 #if !defined(CONFIG_SYS_RAMBOOT)
 	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;

board/freescale/mpc8641hpcn/config.mk

@@ -25,7 +25,7 @@
 # default CCSRBAR is at 0xff700000
 # assume U-Boot is less than 0.5MB
 #
-TEXT_BASE = 0xfff00000
+TEXT_BASE = 0xeff00000
 
 PLATFORM_CPPFLAGS += -DCONFIG_MPC86xx=1
 PLATFORM_CPPFLAGS += -DCONFIG_MPC8641=1 -maltivec -mabi=altivec -msoft-float

board/freescale/mpc8641hpcn/law.c

@@ -31,17 +31,21 @@
  * LAW(Local Access Window) configuration:
  *
  * 0x0000_0000     0x7fff_ffff     DDR                     2G
+ * if PCI (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT)
  * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
  * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
- * 0xc000_0000     0xdfff_ffff     RapidIO                 512M
- * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
- * 0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
- * 0xf800_0000     0xf80f_ffff     CCSRBAR                 1M
- * 0xf810_0000     0xf81f_ffff     PIXIS                   1M
- * 0xfe00_0000     0xffff_ffff     FLASH (boot bank)       32M
+ * else if RIO (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT)
+ * 0x8000_0000     0x9fff_ffff     RapidIO                 512M
+ * endif
+ * (prepend 0xf_0000_0000 if CONFIG_PHYS_64BIT)
+ * 0xffc0_0000     0xffc0_ffff     PCI1 IO                 64K
+ * 0xffc1_0000     0xffc1_ffff     PCI2 IO                 64K
+ * 0xffe0_0000     0xffef_ffff     CCSRBAR                 1M
+ * 0xffdf_0000     0xffe0_0000     PIXIS, CF               64K
+ * 0xef80_0000     0xefff_ffff     FLASH (boot bank)       8M
  *
  * Notes:
- *    CCSRBAR don't need a configured Local Access Window.
+ *    CCSRBAR doesn't need a configured Local Access Window.
  *    If flash is 8M at default position (last 8M), no LAW needed.
  */
 
@@ -49,13 +53,16 @@ struct law_entry law_table[] = {
 #if !defined(CONFIG_SPD_EEPROM)
 	SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR_1),
 #endif
-	SET_LAW(CONFIG_SYS_PCI1_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1),
-	SET_LAW(CONFIG_SYS_PCI2_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2),
-	SET_LAW(PIXIS_BASE, LAW_SIZE_2M, LAW_TRGT_IF_LBC),
-	SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_1),
-	SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_2),
-	SET_LAW((CONFIG_SYS_FLASH_BASE & 0xfe000000), LAW_SIZE_32M, LAW_TRGT_IF_LBC),
-	SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO)
+#ifdef CONFIG_PCI
+	SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1),
+	SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2),
+	SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_1),
+	SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_2),
+#elif defined(CONFIG_RIO)
+	SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO),
+#endif
+	SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_LBC),
 };
 
 int num_law_entries = ARRAY_SIZE(law_table);

board/freescale/mpc8641hpcn/mpc8641hpcn.c

@@ -33,7 +33,7 @@
 
 #include "../common/pixis.h"
 
-long int fixed_sdram(void);
+phys_size_t fixed_sdram(void);
 
 int board_early_init_f(void)
 {
@@ -53,7 +53,7 @@ int checkboard(void)
 phys_size_t
 initdram(int board_type)
 {
-	long dram_size = 0;
+	phys_size_t dram_size = 0;
 
 #if defined(CONFIG_SPD_EEPROM)
 	dram_size = fsl_ddr_sdram();
@@ -75,7 +75,7 @@ initdram(int board_type)
 /*
  * Fixed sdram init -- doesn't use serial presence detect.
  */
-long int
+phys_size_t
 fixed_sdram(void)
 {
 #if !defined(CONFIG_SYS_RAMBOOT)
@@ -121,27 +121,7 @@ fixed_sdram(void)
 
 
 #if defined(CONFIG_PCI)
-/*
- * Initialize PCI Devices, report devices found.
- */
-
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_fsl86xxads_config_table[] = {
-	{PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
-	 PCI_IDSEL_NUMBER, PCI_ANY_ID,
-	 pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
-				     PCI_ENET0_MEMADDR,
-				     PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER}},
-	{}
-};
-#endif
-
-
-static struct pci_controller pci1_hose = {
-#ifndef CONFIG_PCI_PNP
-	config_table:pci_mpc86xxcts_config_table
-#endif
-};
+static struct pci_controller pci1_hose;
 #endif /* CONFIG_PCI */
 
 #ifdef CONFIG_PCI2
@@ -155,17 +135,16 @@ extern void fsl_pci_init(struct pci_controller *hose);
 
 void pci_init_board(void)
 {
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
-	volatile ccsr_gur_t *gur = &immap->im_gur;
-	uint devdisr = gur->devdisr;
-	uint io_sel = (gur->pordevsr & MPC8641_PORDEVSR_IO_SEL)
-		>> MPC8641_PORDEVSR_IO_SEL_SHIFT;
-
 #ifdef CONFIG_PCI1
 {
 	volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
 	struct pci_controller *hose = &pci1_hose;
 	struct pci_region *r = hose->regions;
+	volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+	uint devdisr = gur->devdisr;
+	uint io_sel = (gur->pordevsr & MPC8641_PORDEVSR_IO_SEL)
+		>> MPC8641_PORDEVSR_IO_SEL_SHIFT;
 
 #ifdef DEBUG
 	uint host1_agent = (gur->porbmsr & MPC8641_PORBMSR_HA)
@@ -275,6 +254,10 @@ extern void ft_fsl_pci_setup(void *blob, const char *pci_alias,
 void
 ft_board_setup(void *blob, bd_t *bd)
 {
+	int off;
+	u64 *tmp;
+	u32 *addrcells;
+
 	ft_cpu_setup(blob, bd);
 
 #ifdef CONFIG_PCI1
@@ -283,6 +266,29 @@ ft_board_setup(void *blob, bd_t *bd)
 #ifdef CONFIG_PCI2
 	ft_fsl_pci_setup(blob, "pci1", &pci2_hose);
 #endif
+
+	/*
+	 * Warn if it looks like the device tree doesn't match u-boot.
+	 * This is just an estimation, based on the location of CCSR,
+	 * which is defined by the "reg" property in the soc node.
+	 */
+	off = fdt_path_offset(blob, "/soc8641");
+	addrcells = (u32 *)fdt_getprop(blob, 0, "#address-cells", NULL);
+	tmp = (u64 *)fdt_getprop(blob, off, "reg", NULL);
+
+	if (tmp) {
+		u64 addr;
+		if (addrcells && (*addrcells == 1))
+			addr = *(u32 *)tmp;
+		else
+			addr = *tmp;
+
+		if (addr != CONFIG_SYS_CCSRBAR_PHYS)
+			printf("WARNING: The CCSRBAR address in your .dts "
+			       "does not match the address of the CCSR "
+			       "in u-boot.  This means your .dts might "
+			       "be old.\n");
+	}
 }
 #endif
 

cpu/mpc86xx/Makefile

@@ -31,6 +31,10 @@ LIB	= $(obj)lib$(CPU).a
 START	= start.o
 SOBJS	= cache.o
 
+ifneq ($(CONFIG_NUM_CPUS),1)
+COBJS-y += mp.o
+SOBJS += release.o
+endif
 COBJS-y	+= traps.o
 COBJS-y	+= cpu.o
 COBJS-y	+= cpu_init.o

cpu/mpc86xx/cpu_init.c

@@ -31,6 +31,9 @@
 #include <mpc86xx.h>
 #include <asm/mmu.h>
 #include <asm/fsl_law.h>
+#include "mp.h"
+
+void setup_bats(void);
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -56,6 +59,8 @@ void cpu_init_f(void)
 	init_laws();
 #endif
 
+	setup_bats();
+
 	/* Map banks 0 and 1 to the FLASH banks 0 and 1 at preliminary
 	 * addresses - these have to be modified later when FLASH size
 	 * has been determined
@@ -121,6 +126,9 @@ void cpu_init_f(void)
  */
 int cpu_init_r(void)
 {
+#if (CONFIG_NUM_CPUS > 1)
+	setup_mp();
+#endif
 	return 0;
 }
 

cpu/mpc86xx/fdt.c

@@ -9,9 +9,17 @@
 #include <common.h>
 #include <libfdt.h>
 #include <fdt_support.h>
+#include "mp.h"
+
+DECLARE_GLOBAL_DATA_PTR;
 
 void ft_cpu_setup(void *blob, bd_t *bd)
 {
+#if (CONFIG_NUM_CPUS > 1)
+	int off;
+	u32 bootpg;
+#endif
+
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
 			     "timebase-frequency", bd->bi_busfreq / 4, 1);
 	do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
@@ -32,4 +40,17 @@ void ft_cpu_setup(void *blob, bd_t *bd)
 	do_fixup_by_compat_u32(blob, "ns16550",
 			       "clock-frequency", CONFIG_SYS_NS16550_CLK, 1);
 #endif
+
+#if (CONFIG_NUM_CPUS > 1)
+	/* if we have 4G or more of memory, put the boot page at 4Gb-1M */
+	if (gd->ram_size > 0xfffff000)
+		bootpg = 0xfff00000;
+	else
+		bootpg = gd->ram_size - (1024 * 1024);
+
+	/* Reserve the boot page so OSes dont use it */
+	off = fdt_add_mem_rsv(blob, bootpg, (u64)4096);
+	if (off < 0)
+		printf("%s: %s\n", __FUNCTION__, fdt_strerror(off));
+#endif
 }

cpu/mpc86xx/mp.c

@@ -0,0 +1,68 @@
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <ioports.h>
+#include <lmb.h>
+#include <asm/io.h>
+#include "mp.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if (CONFIG_NUM_CPUS > 1)
+void cpu_mp_lmb_reserve(struct lmb *lmb)
+{
+	u32 bootpg;
+
+	/* if we have 4G or more of memory, put the boot page at 4Gb-1M */
+	if ((u64)gd->ram_size > 0xfffff000)
+		bootpg = 0xfff00000;
+	else
+		bootpg = gd->ram_size - (1024 * 1024);
+
+	/* tell u-boot we stole a page */
+	lmb_reserve(lmb, bootpg, 4096);
+}
+
+/*
+ * Copy the code for other cpus to execute into an
+ * aligned location accessible via BPTR
+ */
+void setup_mp(void)
+{
+	extern ulong __secondary_start_page;
+	ulong fixup = (ulong)&__secondary_start_page;
+	u32 bootpg;
+	u32 bootpg_va;
+
+	/*
+	 * If we have 4G or more of memory, put the boot page at 4Gb-1M.
+	 * Otherwise, put it at the very end of RAM.
+	 */
+	if (gd->ram_size > 0xfffff000)
+		bootpg = 0xfff00000;
+	else
+		bootpg = gd->ram_size - (1024 * 1024);
+
+	if (bootpg >= CONFIG_SYS_MAX_DDR_BAT_SIZE) {
+		/* We're not covered by the DDR mapping, set up BAT  */
+		write_bat(DBAT7, CONFIG_SYS_SCRATCH_VA | BATU_BL_128K |
+			  BATU_VS | BATU_VP,
+			  bootpg | BATL_PP_RW | BATL_MEMCOHERENCE);
+		bootpg_va = CONFIG_SYS_SCRATCH_VA;
+	} else {
+		bootpg_va = bootpg;
+	}
+
+	memcpy((void *)bootpg_va, (void *)fixup, 4096);
+	flush_cache(bootpg_va, 4096);
+
+	/* remove the temporary BAT mapping */
+	if (bootpg >= CONFIG_SYS_MAX_DDR_BAT_SIZE)
+		write_bat(DBAT7, 0, 0);
+
+	/* If the physical location of bootpg is not at fff00000, set BPTR */
+	if (bootpg != 0xfff00000)
+		out_be32((uint *)(CONFIG_SYS_CCSRBAR + 0x20), 0x80000000 |
+			 (bootpg >> 12));
+}
+#endif

cpu/mpc86xx/mp.h

@@ -0,0 +1,7 @@
+#ifndef __MPC86XX_MP_H_
+#define __MPC86XX_MP_H_
+
+void setup_mp(void);
+void cpu_mp_lmb_reserve(struct lmb *lmb);
+
+#endif

cpu/mpc86xx/release.S

@@ -0,0 +1,169 @@
+/*
+ * Copyright 2004, 2007, 2008 Freescale Semiconductor.
+ * Srikanth Srinivasan <srikanth.srinivaan@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <config.h>
+#include <mpc86xx.h>
+#include <version.h>
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+
+#include <asm/cache.h>
+#include <asm/mmu.h>
+
+/* If this is a multi-cpu system then we need to handle the
+ * 2nd cpu.  The assumption is that the 2nd cpu is being
+ * held in boot holdoff mode until the 1st cpu unlocks it
+ * from Linux.	We'll do some basic cpu init and then pass
+ * it to the Linux Reset Vector.
+ * Sri:	 Much of this initialization is not required. Linux
+ * rewrites the bats, and the sprs and also enables the L1 cache.
+ *
+ * Core 0 must copy this to a 1M aligned region and set BPTR
+ * to point to it.
+ */
+#if (CONFIG_NUM_CPUS > 1)
+	.align 12
+.globl __secondary_start_page
+__secondary_start_page:
+	.space 0x100	/* space over to reset vector loc */
+	mfspr	r0, MSSCR0
+	andi.	r0, r0, 0x0020
+	rlwinm	r0,r0,27,31,31
+	mtspr	PIR, r0
+
+	/* Invalidate BATs */
+	li	r0, 0
+	mtspr	IBAT0U, r0
+	mtspr	IBAT1U, r0
+	mtspr	IBAT2U, r0
+	mtspr	IBAT3U, r0
+	mtspr	IBAT4U, r0
+	mtspr	IBAT5U, r0
+	mtspr	IBAT6U, r0
+	mtspr	IBAT7U, r0
+	isync
+	mtspr	DBAT0U, r0
+	mtspr	DBAT1U, r0
+	mtspr	DBAT2U, r0
+	mtspr	DBAT3U, r0
+	mtspr	DBAT4U, r0
+	mtspr	DBAT5U, r0
+	mtspr	DBAT6U, r0
+	mtspr	DBAT7U, r0
+	isync
+	sync
+
+	/* enable extended addressing */
+	mfspr	r0, HID0
+	lis	r0, (HID0_HIGH_BAT_EN | HID0_XBSEN | HID0_XAEN)@h
+	ori	r0, r0, (HID0_HIGH_BAT_EN | HID0_XBSEN | HID0_XAEN)@l
+	mtspr	HID0, r0
+	sync
+	isync
+
+#ifdef CONFIG_SYS_L2
+	/* init the L2 cache */
+	addis	r3, r0, L2_INIT@h
+	ori	r3, r3, L2_INIT@l
+	sync
+	mtspr	l2cr, r3
+#ifdef CONFIG_ALTIVEC
+	dssall
+#endif
+	/* invalidate the L2 cache */
+	mfspr	r3, l2cr
+	rlwinm.	r3, r3, 0, 0, 0
+	beq	1f
+
+	mfspr	r3, l2cr
+	rlwinm	r3, r3, 0, 1, 31
+
+#ifdef	CONFIG_ALTIVEC
+	dssall
+#endif
+	sync
+	mtspr	l2cr, r3
+	sync
+1:	mfspr	r3, l2cr
+	oris	r3, r3, L2CR_L2I@h
+	mtspr	l2cr, r3
+
+invl2:
+	mfspr	r3, l2cr
+	andis.	r3, r3, L2CR_L2I@h
+	bne	invl2
+	sync
+#endif
+
+	/* enable and invalidate the data cache */
+	mfspr	r3, HID0
+	li	r5, HID0_DCFI|HID0_DLOCK
+	andc	r3, r3, r5
+	mtspr	HID0, r3		/* no invalidate, unlock */
+	ori	r3, r3, HID0_DCE
+	ori	r5, r3, HID0_DCFI
+	mtspr	HID0, r5		/* enable + invalidate */
+	mtspr	HID0, r3		/* enable */
+	sync
+#ifdef CFG_L2
+	sync
+	lis	r3, L2_ENABLE@h
+	ori	r3, r3, L2_ENABLE@l
+	mtspr	l2cr, r3
+	isync
+	sync
+#endif
+
+	/* enable and invalidate the instruction cache*/
+	mfspr	r3, HID0
+	li	r5, HID0_ICFI|HID0_ILOCK
+	andc	r3, r3, r5
+	ori	r3, r3, HID0_ICE
+	ori	r5, r3, HID0_ICFI
+	mtspr	HID0, r5
+	mtspr	HID0, r3
+	isync
+	sync
+
+	/* TBEN in HID0 */
+	mfspr	r4, HID0
+	oris	r4, r4, 0x0400
+	mtspr	HID0, r4
+	sync
+	isync
+
+	/* MCP|SYNCBE|ABE in HID1 */
+	mfspr	r4, HID1
+	oris	r4, r4, 0x8000
+	ori	r4, r4, 0x0C00
+	mtspr	HID1, r4
+	sync
+	isync
+
+	lis	r3, CONFIG_LINUX_RESET_VEC@h
+	ori	r3, r3, CONFIG_LINUX_RESET_VEC@l
+	mtlr	r3
+	blr
+
+	/* Never Returns, Running in Linux Now */
+#endif

cpu/mpc86xx/start.S

@@ -179,20 +179,10 @@ _end_of_vectors:
 
 boot_cold:
 boot_warm:
-
-	/* if this is a multi-core system we need to check which cpu
-	 * this is, if it is not cpu 0 send the cpu to the linux reset
-	 * vector */
-#if (CONFIG_NUM_CPUS > 1)
-	mfspr	r0, MSSCR0
-	andi.	r0, r0, 0x0020
-	rlwinm	r0,r0,27,31,31
-	mtspr	PIR, r0
-	beq	1f
-
-	bl	secondary_cpu_setup
-#endif
-
+	/*
+	 * NOTE: Only Cpu 0 will ever come here.  Other cores go to an
+	 * address specified by the BPTR
+	 */
 1:
 #ifdef CONFIG_SYS_RAMBOOT
 	/* disable everything */
@@ -222,8 +212,8 @@ boot_warm:
 	/*
 	 * Calculate absolute address in FLASH and jump there
 	 *------------------------------------------------------*/
-	lis	r3, CONFIG_SYS_MONITOR_BASE@h
-	ori	r3, r3, CONFIG_SYS_MONITOR_BASE@l
+	lis	r3, CONFIG_SYS_MONITOR_BASE_EARLY@h
+	ori	r3, r3, CONFIG_SYS_MONITOR_BASE_EARLY@l
 	addi	r3, r3, in_flash - _start + EXC_OFF_SYS_RESET
 	mtlr	r3
 	blr
@@ -249,9 +239,15 @@ in_flash:
 	 */
 
 	/* enable address translation */
-	bl	enable_addr_trans
-	sync
+	mfmsr	r5
+	ori	r5, r5, (MSR_IR | MSR_DR)
+	lis	r3,addr_trans_enabled@h
+	ori	r3, r3, addr_trans_enabled@l
+	mtspr	SPRN_SRR0,r3
+	mtspr	SPRN_SRR1,r5
+	rfi
 
+addr_trans_enabled:
 	/* enable and invalidate the data cache */
 /*	bl	l1dcache_enable */
 	bl	dcache_enable
@@ -266,6 +262,10 @@ in_flash:
 	sync
 #endif
 
+#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
+	bl      setup_ccsrbar
+#endif
+
 	/* set up the stack pointer in our newly created
 	 * cache-ram (r1) */
 	lis	r1, (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@h
@@ -277,15 +277,6 @@ in_flash:
 
 	GET_GOT			/* initialize GOT access	*/
 
-	/* setup the rest of the bats */
-	bl      setup_bats
-	sync
-
-#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
-	/* setup ccsrbar */
-	bl      setup_ccsrbar
-#endif
-
 	/* run low-level CPU init code	   (from Flash) */
 	bl	cpu_init_f
 	sync
@@ -293,7 +284,7 @@ in_flash:
 #ifdef	RUN_DIAG
 
 	/* Load PX_AUX register address in r4 */
-	lis	r4, 0xf810
+	lis	r4, PIXIS_BASE@h
 	ori	r4, r4, 0x6
 	/* Load contents of PX_AUX in r3 bits 24 to 31*/
 	lbz	r3, 0(r4)
@@ -365,10 +356,28 @@ invalidate_bats:
  * early_bats:
  *
  * Set up bats needed early on - this is usually the BAT for the
- * stack-in-cache and the Flash
+ * stack-in-cache, the Flash, and CCSR space
  */
 	.globl  early_bats
 early_bats:
+	/* IBAT 3 */
+	lis	r4, CONFIG_SYS_IBAT3L@h
+	ori     r4, r4, CONFIG_SYS_IBAT3L@l
+	lis	r3, CONFIG_SYS_IBAT3U@h
+	ori     r3, r3, CONFIG_SYS_IBAT3U@l
+	mtspr   IBAT3L, r4
+	mtspr   IBAT3U, r3
+	isync
+
+	/* DBAT 3 */
+	lis	r4, CONFIG_SYS_DBAT3L@h
+	ori     r4, r4, CONFIG_SYS_DBAT3L@l
+	lis	r3, CONFIG_SYS_DBAT3U@h
+	ori     r3, r3, CONFIG_SYS_DBAT3U@l
+	mtspr   DBAT3L, r4
+	mtspr   DBAT3U, r3
+	isync
+
 	/* IBAT 5 */
 	lis	r4, CONFIG_SYS_IBAT5L@h
 	ori     r4, r4, CONFIG_SYS_IBAT5L@l
@@ -388,22 +397,42 @@ early_bats:
 	isync
 
 	/* IBAT 6 */
-	lis	r4, CONFIG_SYS_IBAT6L@h
-	ori     r4, r4, CONFIG_SYS_IBAT6L@l
-	lis	r3, CONFIG_SYS_IBAT6U@h
-	ori     r3, r3, CONFIG_SYS_IBAT6U@l
+	lis	r4, CONFIG_SYS_IBAT6L_EARLY@h
+	ori     r4, r4, CONFIG_SYS_IBAT6L_EARLY@l
+	lis	r3, CONFIG_SYS_IBAT6U_EARLY@h
+	ori     r3, r3, CONFIG_SYS_IBAT6U_EARLY@l
 	mtspr   IBAT6L, r4
 	mtspr   IBAT6U, r3
 	isync
 
 	/* DBAT 6 */
-	lis	r4, CONFIG_SYS_DBAT6L@h
-	ori     r4, r4, CONFIG_SYS_DBAT6L@l
-	lis	r3, CONFIG_SYS_DBAT6U@h
-	ori     r3, r3, CONFIG_SYS_DBAT6U@l
+	lis	r4, CONFIG_SYS_DBAT6L_EARLY@h
+	ori     r4, r4, CONFIG_SYS_DBAT6L_EARLY@l
+	lis	r3, CONFIG_SYS_DBAT6U_EARLY@h
+	ori     r3, r3, CONFIG_SYS_DBAT6U_EARLY@l
 	mtspr   DBAT6L, r4
 	mtspr   DBAT6U, r3
 	isync
+
+#if(CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
+	/* IBAT 7 */
+	lis	r4, CONFIG_SYS_CCSR_DEFAULT_IBATL@h
+	ori     r4, r4, CONFIG_SYS_CCSR_DEFAULT_IBATL@l
+	lis	r3, CONFIG_SYS_CCSR_DEFAULT_IBATU@h
+	ori     r3, r3, CONFIG_SYS_CCSR_DEFAULT_IBATU@l
+	mtspr   IBAT7L, r4
+	mtspr   IBAT7U, r3
+	isync
+
+	/* DBAT 7 */
+	lis	r4, CONFIG_SYS_CCSR_DEFAULT_DBATL@h
+	ori     r4, r4, CONFIG_SYS_CCSR_DEFAULT_DBATL@l
+	lis	r3, CONFIG_SYS_CCSR_DEFAULT_DBATU@h
+	ori     r3, r3, CONFIG_SYS_CCSR_DEFAULT_DBATU@l
+	mtspr   DBAT7L, r4
+	mtspr   DBAT7U, r3
+	isync
+#endif
 	blr
 
 	.globl clear_tlbs
@@ -419,15 +448,6 @@ tlblp:
 	blt tlblp
 	blr
 
-	.globl enable_addr_trans
-enable_addr_trans:
-	/* enable address translation */
-	mfmsr	r5
-	ori	r5, r5, (MSR_IR | MSR_DR)
-	mtmsr	r5
-	isync
-	blr
-
 	.globl disable_addr_trans
 disable_addr_trans:
 	/* disable address translation */
@@ -859,17 +879,20 @@ setup_ccsrbar:
 	lis	r4, CONFIG_SYS_CCSRBAR_DEFAULT@h
 	ori	r4, r4, CONFIG_SYS_CCSRBAR_DEFAULT@l
 
-	lis	r5, CONFIG_SYS_CCSRBAR@h
-	ori	r5, r5, CONFIG_SYS_CCSRBAR@l
-	srwi	r6,r5,12
-	stw	r6, 0(r4)
+	lis	r5, CONFIG_SYS_CCSRBAR_PHYS_LOW@h
+	ori	r5, r5, CONFIG_SYS_CCSRBAR_PHYS_LOW@l
+	srwi	r5,r5,12
+	li	r6, CONFIG_SYS_CCSRBAR_PHYS_HIGH@l
+	rlwimi	r5,r6,20,8,11
+	stw	r5, 0(r4) /* Store physical value of CCSR */
 	isync
 
-	lis	r5, 0xffff
-	ori	r5,r5,0xf000
+	lis	r5, TEXT_BASE@h
+	ori	r5,r5,TEXT_BASE@l
 	lwz	r5, 0(r5)
 	isync
 
+	/* Use VA of CCSR to do read */
 	lis	r3, CONFIG_SYS_CCSRBAR@h
 	lwz	r5, CONFIG_SYS_CCSRBAR@l(r3)
 	isync
@@ -959,63 +982,4 @@ unlock_ram_in_cache:
 #endif
 #endif
 
-/* If this is a multi-cpu system then we need to handle the
- * 2nd cpu.  The assumption is that the 2nd cpu is being
- * held in boot holdoff mode until the 1st cpu unlocks it
- * from Linux.	We'll do some basic cpu init and then pass
- * it to the Linux Reset Vector.
- * Sri:	 Much of this initialization is not required. Linux
- * rewrites the bats, and the sprs and also enables the L1 cache.
- */
-#if (CONFIG_NUM_CPUS > 1)
-.globl secondary_cpu_setup
-secondary_cpu_setup:
-	/* Do only core setup on all cores except cpu0 */
-	bl	invalidate_bats
-	sync
-	bl	enable_ext_addr
-
-#ifdef CONFIG_SYS_L2
-	/* init the L2 cache */
-	addis	r3, r0, L2_INIT@h
-	ori	r3, r3, L2_INIT@l
-	sync
-	mtspr	l2cr, r3
-#ifdef CONFIG_ALTIVEC
-	dssall
-#endif
-	/* invalidate the L2 cache */
-	bl	l2cache_invalidate
-	sync
-#endif
 
-	/* enable and invalidate the data cache */
-	bl	dcache_enable
-	sync
-
-	/* enable and invalidate the instruction cache*/
-	bl	icache_enable
-	sync
-
-	/* TBEN in HID0 */
-	mfspr	r4, HID0
-	oris	r4, r4, 0x0400
-	mtspr	HID0, r4
-	sync
-	isync
-
-	/* MCP|SYNCBE|ABE in HID1 */
-	mfspr	r4, HID1
-	oris	r4, r4, 0x8000
-	ori	r4, r4, 0x0C00
-	mtspr	HID1, r4
-	sync
-	isync
-
-	lis	r3, CONFIG_LINUX_RESET_VEC@h
-	ori	r3, r3, CONFIG_LINUX_RESET_VEC@l
-	mtlr	r3
-	blr
-
-	/* Never Returns, Running in Linux Now */
-#endif

doc/README.mpc8641hpcn

@@ -79,51 +79,77 @@ Switches:
 
 3. Flash U-Boot
 ---------------
-The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves.
+The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves.
 It is possible to use either half to boot using u-boot.  Switch 5 bit 2
 is used for this purpose.
 
-0xFF800000 to 0xFFBFFFFF - 4MB
-0xFFC00000 to 0xFFFFFFFF - 4MB
-When this bit is 0, U-Boot is at 0xFFF00000.
-When this bit is 1, U-Boot is at 0xFFB00000.
+0xEF800000 to 0xEFBFFFFF - 4MB
+0xEFC00000 to 0xEFFFFFFF - 4MB
+When this bit is 0, U-Boot is at 0xEFF00000.
+When this bit is 1, U-Boot is at 0xEFB00000.
 
 Use the above mentioned flash commands to program the other half, and
 use switch 5, bit 2 to alternate between the halves.  Note: The booting
-version of U-Boot will always be at 0xFFF00000.
+version of U-Boot will always be at 0xEFF00000.
 
-To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF):
+To Flash U-Boot into the booting bank (0xEFC00000 - 0xEFFFFFFF):
 
 	tftp 1000000 u-boot.bin
 	protect off all
-	erase fff00000 +$filesize
-	cp.b 1000000 fff00000 $filesize
+	erase eff00000 +$filesize
+	cp.b 1000000 eff00000 $filesize
 
 or use tftpflash command:
 	run tftpflash
 
-To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF):
+To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF):
 
 	tftp 1000000 u-boot.bin
-	erase ffb00000 +$filesize
-	cp.b 1000000 ffb00000 $filesize
+	erase efb00000 +$filesize
+	cp.b 1000000 efb00000 $filesize
 
 
 4. Memory Map
 -------------
+NOTE:  RIO and PCI are mutually exclusive, so they share an address
+
+For 32-bit u-boot, devices are mapped so that the virtual address ==
+the physical address, and the map looks liks this:
 
 	Memory Range			Device		Size
 	------------			------		----
 	0x0000_0000	0x7fff_ffff	DDR		2G
+	0x8000_0000	0x9fff_ffff	RIO MEM		512M
 	0x8000_0000	0x9fff_ffff	PCI1/PEX1 MEM	512M
-	0xa000_0000	0xafff_ffff	PCI2/PEX2 MEM	512M
-	0xf800_0000	0xf80f_ffff	CCSR		1M
-	0xf810_0000	0xf81f_ffff	PIXIS		1M
+	0xa000_0000	0xbfff_ffff	PCI2/PEX2 MEM	512M
+	0xffe0_0000	0xffef_ffff	CCSR		1M
+	0xffdf_0000	0xffdf_7fff	PIXIS		8K
+	0xffdf_8000	0xffdf_ffff	CF		8K
 	0xf840_0000	0xf840_3fff	Stack space	32K
-	0xe200_0000	0xe2ff_ffff	PCI1/PEX1 IO	16M
-	0xe300_0000	0xe3ff_ffff	PCI2/PEX2 IO	16M
-	0xfe00_0000	0xfeff_ffff	Flash(alternate)16M
-	0xff00_0000	0xffff_ffff	Flash(boot bank)16M
+	0xffc0_0000	0xffc0_ffff	PCI1/PEX1 IO	64K
+	0xffc1_0000	0xffc1_ffff	PCI2/PEX2 IO	64K
+	0xef80_0000	0xefff_ffff	Flash		8M
+
+For 36-bit-enabled u-boot, the virtual map is the same as for 32-bit.
+However, the physical map is altered to reside in 36-bit space, as follows.
+Addresses are no longer mapped with VA == PA.  All accesses from
+software use the VA; the PA is only used for setting up windows
+and mappings. Note that the low 32 bits are the same as the VA above;
+only the top 4 bits vary:
+
+	Memory Range			Device		Size
+	------------			------		----
+	0x0_0000_0000	0x0_7fff_ffff	DDR		2G
+	0xc_8000_0000	0xc_9fff_ffff	RIO MEM		512M
+	0xc_8000_0000	0xc_9fff_ffff	PCI1/PEX1 MEM	512M
+	0xc_a000_0000	0xc_bfff_ffff	PCI2/PEX2 MEM	512M
+	0xf_ffe0_0000	0xf_ffef_ffff	CCSR		1M
+	0xf_ffdf_0000	0xf_ffdf_7fff	PIXIS		8K
+	0xf_ffdf_8000	0xf_ffdf_ffff	CF		8K
+	0x0_f840_0000	0xf_f840_3fff	Stack space	32K
+	0xf_ffc0_0000	0xf_ffc0_ffff	PCI1/PEX1 IO	64K
+	0xf_ffc1_0000	0xf_ffc1_ffff	PCI2/PEX2 IO	64K
+	0xf_ef80_0000	0xf_efff_ffff	Flash		8M
 
 5. pixis_reset command
 --------------------

include/configs/MPC8610HPCD.h

@@ -36,6 +36,12 @@
 
 #define CONFIG_SYS_RESET_ADDRESS	0xfff00100
 
+/*
+ * virtual address to be used for temporary mappings.  There
+ * should be 128k free at this VA.
+ */
+#define CONFIG_SYS_SCRATCH_VA	0xc0000000
+
 #define CONFIG_PCI		1	/* Enable PCI/PCIE*/
 #define CONFIG_PCI1		1	/* PCI controler 1 */
 #define CONFIG_PCIE1		1	/* PCIe 1 connected to ULI bridge */
@@ -92,6 +98,7 @@
 
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
 #define CONFIG_VERY_BIG_RAM
 
 #define MPC86xx_DDR_SDRAM_CLK_CNTL
@@ -180,6 +187,7 @@
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 #define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000	/* early monitor loc */
 
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -370,27 +378,29 @@
 #define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
 
 /*
- * BAT3		32M	Cache-inhibited, guarded
- * 0xe200_0000	1M	PCI-Express 2 I/O
- * 0xe300_0000	1M	PCI-Express 1 I/O
+ * BAT3		4M	Cache-inhibited, guarded
+ * 0xe000_0000	4M	CCSR
  */
 
-#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U	(CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U
 
 /*
- * BAT4		4M	Cache-inhibited, guarded
- * 0xe000_0000	4M	CCSR
+ * BAT4		32M	Cache-inhibited, guarded
+ * 0xe200_0000	1M	PCI-Express 2 I/O
+ * 0xe300_0000	1M	PCI-Express 1 I/O
  */
-#define CONFIG_SYS_DBAT4L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
+
+#define CONFIG_SYS_DBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U	(CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U
 
+
 /*
  * BAT5		128K	Cacheable, non-guarded
  * 0xe400_0000	128K	Init RAM for stack in the CPU DCache (no backing memory)
@@ -410,6 +420,14 @@
 #define CONFIG_SYS_IBAT6L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
 
+/* Map the last 1M of flash where we're running from reset */
+#define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+				 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U_EARLY	(TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+				 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY
+
 /*
  * BAT7		4M	Cache-inhibited, guarded
  * 0xe800_0000	4M	PIXIS

include/configs/MPC8641HPCN.h

@@ -38,18 +38,32 @@
 #define CONFIG_MPC8641HPCN	1	/* MPC8641HPCN board specific */
 #define CONFIG_NUM_CPUS		2	/* Number of CPUs in the system */
 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
+/*#define CONFIG_PHYS_64BIT	1*/	/* Place devices in 36-bit space */
 
 #ifdef RUN_DIAG
-#define CONFIG_SYS_DIAG_ADDR	     0xff800000
+#define CONFIG_SYS_DIAG_ADDR	     CONFIG_SYS_FLASH_BASE
 #endif
 
 #define CONFIG_SYS_RESET_ADDRESS    0xfff00100
 
+/*
+ * virtual address to be used for temporary mappings.  There
+ * should be 128k free at this VA.
+ */
+#define CONFIG_SYS_SCRATCH_VA	0xe0000000
+
+/*
+ * set this to enable Rapid IO.  PCI and RIO are mutually exclusive
+ */
+/*#define CONFIG_RIO		1*/
+
+#ifndef CONFIG_RIO			/* RIO/PCI are mutually exclusive */
 #define CONFIG_PCI		1	/* Enable PCI/PCIE */
 #define CONFIG_PCI1		1	/* PCIE controler 1 (ULI bridge) */
 #define CONFIG_PCI2		1	/* PCIE controler 2 (slot) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
+#endif
 #define CONFIG_FSL_LAW		1	/* Use common FSL law init code */
 
 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
@@ -78,14 +92,36 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
+/*
+ * With the exception of PCI Memory and Rapid IO, most devices will simply
+ * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA
+ * when 36-bit is enabled.  When 36-bit is not enabled, these bits are 0.
+ */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f00000000ULL
+#else
+#define CONFIG_SYS_PHYS_ADDR_HIGH 0x0
+#endif
+
 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xf8000000	/* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
 
+/* Physical addresses */
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0xf
+#define CONFIG_SYS_CCSRBAR_PHYS		(CONFIG_SYS_CCSRBAR_PHYS_LOW \
+					 | ((u64)CONFIG_SYS_CCSRBAR_PHYS_HIGH << 32))
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
+#define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR_PHYS_LOW
+#endif
+
 #define CONFIG_SYS_PCI1_ADDR		(CONFIG_SYS_CCSRBAR+0x8000)
 #define CONFIG_SYS_PCI2_ADDR		(CONFIG_SYS_CCSRBAR+0x9000)
 
@@ -102,6 +138,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
 #define CONFIG_VERY_BIG_RAM
 
 #define MPC86xx_DDR_SDRAM_CLK_CNTL
@@ -145,38 +182,46 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 
-/*
- * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
- * There is an 8MB flash.  In effect, the addresses from fe000000 to fe7fffff
- * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
- * However, when u-boot comes up, the flash_init needs hard start addresses
- * to build its info table.  For user convenience, the flash addresses is
- * fe800000 and ff800000.  That way, u-boot knows where the flash is
- * and the user can download u-boot code from promjet to fef00000, a
- * more intuitive location than fe700000.
- *
- * Note that, on switching the boot location, fef00000 becomes fff00000.
- */
-#define CONFIG_SYS_FLASH_BASE		0xfe800000     /* start of FLASH 32M */
-#define CONFIG_SYS_FLASH_BASE2		0xff800000
+#define CONFIG_SYS_FLASH_BASE		0xef800000     /* start of FLASH 8M */
+#define CONFIG_SYS_FLASH_BASE_PHYS	(CONFIG_SYS_FLASH_BASE \
+					 | CONFIG_SYS_PHYS_ADDR_HIGH)
 
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 
-#define CONFIG_SYS_BR0_PRELIM		0xff001001	/* port size 16bit */
-#define CONFIG_SYS_OR0_PRELIM		0xff006ff7	/* 16MB Boot Flash area*/
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
 
-#define CONFIG_SYS_BR1_PRELIM		0xfe001001	/* port size 16bit */
-#define CONFIG_SYS_OR1_PRELIM		0xff006ff7	/* 16MB Alternate Boot Flash area*/
+/* Convert an address into the right format for the BR registers */
+#ifdef CONFIG_PHYS_64BIT
+#define BR_PHYS_ADDR(x)	((unsigned long)((x & 0x0ffff8000ULL) | \
+					 ((x & 0x300000000ULL) >> 19)))
+#else
+#define BR_PHYS_ADDR(x) (x & 0xffff8000)
+#endif
+
+#define CONFIG_SYS_BR0_PRELIM	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+				 | 0x00001001)	/* port size 16bit */
+#define CONFIG_SYS_OR0_PRELIM	0xff806ff7	/* 8MB Boot Flash area*/
 
-#define CONFIG_SYS_BR2_PRELIM		0xf8201001	/* port size 16bit */
-#define CONFIG_SYS_OR2_PRELIM		0xfff06ff7	/* 1MB Compact Flash area*/
+#define CONFIG_SYS_BR2_PRELIM	(BR_PHYS_ADDR(CF_BASE_PHYS)		\
+				 | 0x00001001)	/* port size 16bit */
+#define CONFIG_SYS_OR2_PRELIM	0xffffeff7	/* 32k Compact Flash */
 
-#define CONFIG_SYS_BR3_PRELIM		0xf8100801	/* port size 8bit */
-#define CONFIG_SYS_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
+#define CONFIG_SYS_BR3_PRELIM	(BR_PHYS_ADDR(PIXIS_BASE_PHYS)	\
+				 | 0x00000801) /* port size 8bit */
+#define CONFIG_SYS_OR3_PRELIM	0xffffeff7	/* 32k PIXIS area*/
 
+/*
+ * The LBC_BASE is the base of the region that contains the PIXIS and the CF.
+ * The PIXIS and CF by themselves aren't large enough to take up the 128k
+ * required for the smallest BAT mapping, so there's a 64k hole.
+ */
+#define CONFIG_SYS_LBC_BASE		0xffde0000
+#define CONFIG_SYS_LBC_BASE_PHYS	(CONFIG_SYS_LBC_BASE \
+					 | CONFIG_SYS_PHYS_ADDR_HIGH)
 
 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
-#define PIXIS_BASE	0xf8100000	/* PIXIS registers */
+#define PIXIS_BASE		(CONFIG_SYS_LBC_BASE + 0x00010000)
+#define PIXIS_BASE_PHYS 	(CONFIG_SYS_LBC_BASE_PHYS + 0x00010000)
+#define PIXIS_SIZE		0x00008000	/* 32k */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
 #define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
@@ -193,13 +238,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
 #define CONFIG_SYS_PIXIS_VBOOT_MASK	0x40	/* Reset altbank mask*/
 
-#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
+/* Compact flash shares a BAT with PIXIS; make sure they're contiguous */
+#define CF_BASE			(PIXIS_BASE + PIXIS_SIZE)
+#define CF_BASE_PHYS		(PIXIS_BASE_PHYS + PIXIS_SIZE)
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
 
 #undef	CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE		TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000	/* early monitor loc */
 
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -279,8 +329,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * RapidIO MMU
  */
-#define CONFIG_SYS_RIO_MEM_BASE	0xc0000000	/* base address */
+#define CONFIG_SYS_RIO_MEM_BASE	0x80000000	/* base address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_RIO_MEM_PHYS  0x0000000c00000000ULL
+#else
 #define CONFIG_SYS_RIO_MEM_PHYS	CONFIG_SYS_RIO_MEM_BASE
+#endif
 #define CONFIG_SYS_RIO_MEM_SIZE	0x20000000	/* 128M */
 
 /*
@@ -288,22 +342,33 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCI1_MEM_PHYS	0x0000000c00000000ULL
+#else
 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#endif
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCI1_IO_BASE	0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS	0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCI1_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCI1_IO_PHYS	(CONFIG_SYS_PCI1_IO_VIRT \
+				 | CONFIG_SYS_PHYS_ADDR_HIGH)
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00010000	/* 64K */
 
 /* For RTL8139 */
 #define KSEG1ADDR(x)		({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
 #define _IO_BASE		0x00000000
 
-#define CONFIG_SYS_PCI2_MEM_BASE	0xa0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_BASE 	(CONFIG_SYS_PCI1_MEM_BASE \
+					 + CONFIG_SYS_PCI1_MEM_SIZE)
+#define CONFIG_SYS_PCI2_MEM_PHYS	(CONFIG_SYS_PCI1_MEM_PHYS \
+					 + CONFIG_SYS_PCI1_MEM_SIZE)
 #define CONFIG_SYS_PCI2_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCI2_IO_BASE	0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS	0xe3000000
-#define CONFIG_SYS_PCI2_IO_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCI2_IO_VIRT (CONFIG_SYS_PCI1_IO_VIRT \
+				 + CONFIG_SYS_PCI1_IO_SIZE)
+#define CONFIG_SYS_PCI2_IO_PHYS	(CONFIG_SYS_PCI1_IO_PHYS \
+				 + CONFIG_SYS_PCI1_IO_SIZE)
+#define CONFIG_SYS_PCI2_IO_SIZE	CONFIG_SYS_PCI1_IO_SIZE
 
 #if defined(CONFIG_PCI)
 
@@ -331,17 +396,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	15
 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS	1
 
-#if !defined(CONFIG_PCI_PNP)
-    #define PCI_ENET0_IOADDR	0xe0000000
-    #define PCI_ENET0_MEMADDR	0xe0000000
-    #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
 /*PCIE video card used*/
-#define VIDEO_IO_OFFSET		CONFIG_SYS_PCI2_IO_PHYS
+#define VIDEO_IO_OFFSET		CONFIG_SYS_PCI2_IO_VIRT
 
 /*PCI video card used*/
-/*#define VIDEO_IO_OFFSET	CONFIG_SYS_PCI1_IO_PHYS*/
+/*#define VIDEO_IO_OFFSET	CONFIG_SYS_PCI1_IO_VIRT*/
 
 /* video */
 #define CONFIG_VIDEO
@@ -354,7 +413,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_ATI_RADEON_FB
 #define CONFIG_VIDEO_LOGO
 /*#define CONFIG_CONSOLE_CURSOR*/
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCI2_IO_PHYS
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCI2_IO_VIRT
 #endif
 
 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
@@ -408,9 +467,23 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #endif	/* CONFIG_TSEC_ENET */
 
+/*  Contort an addr into the format needed for BATs */
+#ifdef CONFIG_PHYS_64BIT
+#define BAT_PHYS_ADDR(x)         ((unsigned long) \
+				  ((x & 0x00000000ffffffffULL) |	\
+				   ((x & 0x0000000e00000000ULL) >> 24) | \
+				   ((x & 0x0000000100000000ULL) >> 30)))
+#else
+#define BAT_PHYS_ADDR(x)        (x)
+#endif
+
+
+/* Put high physical address bits into the BAT format */
+#define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8)
+#define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2)
+
 /*
- * BAT0		2G     Cacheable, non-guarded
- * 0x0000_0000	2G     DDR
+ * BAT0		DDR
  */
 #define CONFIG_SYS_DBAT0L	(BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_DBAT0U	(BATU_BL_2G | BATU_VS | BATU_VP)
@@ -418,52 +491,90 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_IBAT0U	CONFIG_SYS_DBAT0U
 
 /*
- * BAT1		1G     Cache-inhibited, guarded
- * 0x8000_0000	512M   PCI-Express 1 Memory
- * 0xa000_0000	512M   PCI-Express 2 Memory
- *	Changed it for operating from 0xd0000000
+ * BAT1		LBC (PIXIS/CF)
  */
-#define CONFIG_SYS_DBAT1L	( CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW \
-			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT1U	(CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_DBAT1L	(BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT | \
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT1U	(CONFIG_SYS_LBC_BASE | BATU_BL_128K \
+				 | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L	(BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS) \
+				 | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT1U	CONFIG_SYS_DBAT1U
 
-/*
- * BAT2		512M   Cache-inhibited, guarded
- * 0xc000_0000	512M   RapidIO Memory
+/* if CONFIG_PCI:
+ * BAT2		PCI1 and PCI1 MEM
+ * if CONFIG_RIO
+ * BAT2		Rapidio Memory
  */
+#ifdef CONFIG_PCI
+#define CONFIG_SYS_DBAT2L	(BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT \
+				 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_1G \
+				 | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
+#else /* CONFIG_RIO */
+#define CONFIG_SYS_DBAT2L	(BAT_PHYS_ADDR(CONFIG_SYS_RIO_MEM_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT | \
+				 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U	(CONFIG_SYS_RIO_MEM_BASE | BATU_BL_512M \
+				 | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(BAT_PHYS_ADDR(CONFIG_SYS_RIO_MEM_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT)
+
 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_RIO_MEM_PHYS | BATL_PP_RW \
 			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT2U	(CONFIG_SYS_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
+#endif
 
 /*
- * BAT3		4M     Cache-inhibited, guarded
- * 0xf800_0000	4M     CCSR
+ * BAT3		CCSR Space
+ * This BAT is used early; don't use any macros with ULL - use HIGH/LOW pairs
+ * instead.  The assembler chokes on ULL.
  */
-#define CONFIG_SYS_DBAT3L	( CONFIG_SYS_CCSRBAR | BATL_PP_RW \
-			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_CCSRBAR_PHYS_LOW \
+				 | PHYS_HIGH_TO_BXPN(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+				 | PHYS_HIGH_TO_BX(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT \
+				 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \
+				 | BATU_VP)
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR_PHYS_LOW \
+				 | PHYS_HIGH_TO_BXPN(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+				 | PHYS_HIGH_TO_BX(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U
 
+#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
+				       | BATL_PP_RW | BATL_CACHEINHIBIT \
+				       | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
+				       | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
+				       | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
+#endif
+
 /*
- * BAT4		32M    Cache-inhibited, guarded
- * 0xe200_0000	16M    PCI-Express 1 I/O
- * 0xe300_0000	16M    PCI-Express 2 I/0
- *    Note that this is at 0xe0000000
+ * BAT4		PCI1_IO and PCI2_IO
  */
-#define CONFIG_SYS_DBAT4L	( CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW \
-			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_DBAT4L	(BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT \
+				 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_128K \
+				 | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L	(BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U
 
 /*
- * BAT5		128K   Cacheable, non-guarded
- * 0xe401_0000	128K   Init RAM for stack in the CPU DCache (no backing memory)
+ * BAT5		Init RAM for stack in the CPU DCache (no backing memory)
  */
 #define CONFIG_SYS_DBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_DBAT5U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
@@ -471,15 +582,28 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_IBAT5U	CONFIG_SYS_DBAT5U
 
 /*
- * BAT6		32M    Cache-inhibited, guarded
- * 0xfe00_0000	32M    FLASH
+ * BAT6		FLASH
  */
-#define CONFIG_SYS_DBAT6L	((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
-			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT6U	((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT6L	((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT6L	(BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+				 | BATL_PP_RW | BATL_CACHEINHIBIT \
+				 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \
+				 | BATU_VP)
+#define CONFIG_SYS_IBAT6L	(BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+				 | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
 
+/* Map the last 1M of flash where we're running from reset */
+#define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+				 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U_EARLY	(TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+				 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY
+
+/*
+ * BAT7		FREE - used later for tmp mappings
+ */
 #define CONFIG_SYS_DBAT7L 0x00000000
 #define CONFIG_SYS_DBAT7U 0x00000000
 #define CONFIG_SYS_IBAT7L 0x00000000
@@ -492,12 +616,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
     #define CONFIG_ENV_IS_IN_FLASH	1
     #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x60000)
     #define CONFIG_ENV_SECT_SIZE		0x10000	/* 64K(one sector) for env */
-    #define CONFIG_ENV_SIZE		0x2000
 #else
     #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
     #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-    #define CONFIG_ENV_SIZE		0x2000
 #endif
+#define CONFIG_ENV_SIZE		0x2000
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
@@ -624,8 +747,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 	"ramdiskfile=your.ramdisk.u-boot\0"				\
 	"fdtaddr=c00000\0"						\
 	"fdtfile=mpc8641_hpcn.dtb\0"					\
-	"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
-	"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+	"en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0"			\
+	"dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \
 	"maxcpus=2"
 
 

include/configs/sbc8641d.h

@@ -49,6 +49,12 @@
 
 #define CONFIG_SYS_RESET_ADDRESS    0xfff00100
 
+/*
+ * virtual address to be used for temporary mappings.  There
+ * should be 128k free at this VA.
+ */
+#define CONFIG_SYS_SCRATCH_VA	0xe8000000
+
 #define CONFIG_PCI		1	/* Enable PCIE */
 #define CONFIG_PCI1		1	/* PCIE controler 1 (slot 1) */
 #define CONFIG_PCI2		1	/* PCIE controler 2 (slot 2) */
@@ -108,6 +114,7 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE2	0x10000000	/* DDR bank 2 */
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_SYS_SDRAM_BASE2		CONFIG_SYS_DDR_SDRAM_BASE2
+#define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
 #define CONFIG_VERY_BIG_RAM
 
 #define MPC86xx_DDR_SDRAM_CLK_CNTL
@@ -224,6 +231,7 @@
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 #define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000	/* early monitor loc */
 
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -456,6 +464,14 @@
 #define CONFIG_SYS_IBAT6L	((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
 
+/* Map the last 1M of flash where we're running from reset */
+#define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+				 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U_EARLY	(TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+				 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY
+
 #define CONFIG_SYS_DBAT7L	0x00000000
 #define CONFIG_SYS_DBAT7U	0x00000000
 #define CONFIG_SYS_IBAT7L	0x00000000

lib_ppc/board.c

@@ -689,6 +689,11 @@ void board_init_r (gd_t *id, ulong dest_addr)
 
 	WATCHDOG_RESET ();
 
+	/*
+	 * Setup trap handlers
+	 */
+	trap_init (dest_addr);
+
 #if defined(CONFIG_BOARD_EARLY_INIT_R)
 	board_early_init_r ();
 #endif
@@ -765,11 +770,6 @@ void board_init_r (gd_t *id, ulong dest_addr)
 
 	asm ("sync ; isync");
 
-	/*
-	 * Setup trap handlers
-	 */
-	trap_init (dest_addr);
-
 #if !defined(CONFIG_SYS_NO_FLASH)
 	puts ("FLASH: ");