powerpc/mpc8548cds: Fix network initialization

Add board_eth_init(). PCIe network card is also supported.
Put RGMII init after tsec_eth_init().
Skip initializing eTSEC3 and eTSEC4 with Carrier boards prior to ver 1.3.

Signed-off-by: Ebony Zhu
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>

board/freescale/mpc8548cds/mpc8548cds.c

@@ -33,6 +33,9 @@
 #include <miiphy.h>
 #include <libfdt.h>
 #include <fdt_support.h>
+#include <tsec.h>
+#include <fsl_mdio.h>
+#include <netdev.h>
 
 #include "../common/cadmus.h"
 #include "../common/eeprom.h"
@@ -287,7 +290,7 @@ void pci_init_board(void)
 	fsl_pcie_init_board(first_free_busno);
 }
 
-int last_stage_init(void)
+void configure_rgmii(void)
 {
 	unsigned short temp;
 
@@ -295,29 +298,77 @@ int last_stage_init(void)
 	/* This is needed to get the RGMII working for the 1.3+
 	 * CDS cards */
 	if (get_board_version() ==  0x13) {
-		miiphy_write(CONFIG_TSEC1_NAME,
+		miiphy_write(DEFAULT_MII_NAME,
 				TSEC1_PHY_ADDR, 29, 18);
 
-		miiphy_read(CONFIG_TSEC1_NAME,
+		miiphy_read(DEFAULT_MII_NAME,
 				TSEC1_PHY_ADDR, 30, &temp);
 
 		temp = (temp & 0xf03f);
 		temp |= 2 << 9;		/* 36 ohm */
 		temp |= 2 << 6;		/* 39 ohm */
 
-		miiphy_write(CONFIG_TSEC1_NAME,
+		miiphy_write(DEFAULT_MII_NAME,
 				TSEC1_PHY_ADDR, 30, temp);
 
-		miiphy_write(CONFIG_TSEC1_NAME,
+		miiphy_write(DEFAULT_MII_NAME,
 				TSEC1_PHY_ADDR, 29, 3);
 
-		miiphy_write(CONFIG_TSEC1_NAME,
+		miiphy_write(DEFAULT_MII_NAME,
 				TSEC1_PHY_ADDR, 30, 0x8000);
 	}
 
-	return 0;
+	return;
 }
 
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+	struct fsl_pq_mdio_info mdio_info;
+	struct tsec_info_struct tsec_info[4];
+	int num = 0;
+
+#ifdef CONFIG_TSEC1
+	SET_STD_TSEC_INFO(tsec_info[num], 1);
+	num++;
+#endif
+#ifdef CONFIG_TSEC2
+	SET_STD_TSEC_INFO(tsec_info[num], 2);
+	num++;
+#endif
+#ifdef CONFIG_TSEC3
+	/* initialize TSEC3 only if Carrier is 1.3 or above on CDS */
+	if (get_board_version() >= 0x13) {
+		SET_STD_TSEC_INFO(tsec_info[num], 3);
+		tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID;
+		num++;
+	}
+#endif
+#ifdef CONFIG_TSEC4
+	/* initialize TSEC4 only if Carrier is 1.3 or above on CDS */
+	if (get_board_version() >= 0x13) {
+		SET_STD_TSEC_INFO(tsec_info[num], 4);
+		tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID;
+		num++;
+	}
+#endif
+
+	if (!num) {
+		printf("No TSECs initialized\n");
+
+		return 0;
+	}
+
+	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+	mdio_info.name = DEFAULT_MII_NAME;
+	fsl_pq_mdio_init(bis, &mdio_info);
+
+	tsec_eth_init(bis, tsec_info, num);
+	configure_rgmii();
+
+	return pci_eth_init(bis);
+}
+#endif
 
 #if defined(CONFIG_OF_BOARD_SETUP)
 void ft_pci_setup(void *blob, bd_t *bd)

include/configs/MPC8548CDS.h

@@ -464,6 +464,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_TSEC4_NAME	"eTSEC3"
 #undef CONFIG_MPC85XX_FEC
 
+#define CONFIG_PHY_MARVELL
+
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC3_PHY_ADDR		2