* The PS/2 mux on the BMS2003 board needs 450 ms after power on

  before we can access it; add delay in case we are faster (with no
  CF card inserted)

* Cleanup of some init functions

* Make sure SCC Ethernet is always stopped by the time we boot Linux
  to avoid Linux crashes by early packets coming in.

* Accelerate flash accesses on LWMON board by using buffered writes

CHANGELOG

@@ -2,6 +2,17 @@
 Changes since U-Boot 1.0.1:
 ======================================================================
 
+* The PS/2 mux on the BMS2003 board needs 450 ms after power on
+  before we can access it; add delay in case we are faster (with no
+  CF card inserted)
+
+* Cleanup of some init functions
+
+* Make sure SCC Ethernet is always stopped by the time we boot Linux
+  to avoid Linux crashes by early packets coming in.
+
+* Accelerate flash accesses on LWMON board by using buffered writes
+
 * Fix typo in Makefile;
   fix problem with PARTNUM detection
 

board/LEOX/elpt860/elpt860.c

@@ -33,7 +33,7 @@
 /*
 ** Note 1: In this file, you have to provide the following functions:
 ** ------
-**              int             board_pre_init(void)
+**              int             board_early_init_f(void)
 **              int             checkboard(void)
 **              long int        initdram(int board_type)
 ** called from 'board_init_f()' into 'common/board.c'
@@ -145,7 +145,7 @@ const uint sdram_table[] = {
 /*
  * Very early board init code (fpga boot, etc.)
  */
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	volatile immap_t *immr = (immap_t *) CFG_IMMR;
 

board/MAI/AmigaOneG3SE/articiaS.c

@@ -675,7 +675,7 @@ static __inline__ void set_msr (unsigned long msr)
 	asm volatile ("mtmsr %0"::"r" (msr));
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	unsigned char c_value = 0;
 	unsigned long msr;

board/Marvell/common/bootseq.txt

@@ -58,7 +58,7 @@ in_flash:
     call cpu_init_f
     	debug leds
     board_init_f: (common/board.c)
-	board_pre_init:
+	board_early_init_f:
 	    remap gt regs?
 	    map PCI mem/io
 	    map device space

board/Marvell/db64360/db64360.c

@@ -61,7 +61,7 @@ extern void invalidate_l1_instruction_cache (void);
 
 /* Unfortunately, we cant change it while we are in flash, so we initialize it
  * to the "final" value. This means that any debug_led calls before
- * board_pre_init wont work right (like in cpu_init_f).
+ * board_early_init_f wont work right (like in cpu_init_f).
  * See also my_remap_gt_regs below. (NTL)
  */
 
@@ -237,11 +237,11 @@ static void gt_cpu_config (void)
 }
 
 /*
- * board_pre_init.
+ * board_early_init_f.
  *
  * set up gal. device mappings, etc.
  */
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	uchar sram_boot = 0;
 

board/Marvell/db64460/db64460.c

@@ -61,7 +61,7 @@ extern void invalidate_l1_instruction_cache (void);
 
 /* Unfortunately, we cant change it while we are in flash, so we initialize it
  * to the "final" value. This means that any debug_led calls before
- * board_pre_init wont work right (like in cpu_init_f).
+ * board_early_init_f wont work right (like in cpu_init_f).
  * See also my_remap_gt_regs below. (NTL)
  */
 
@@ -237,11 +237,11 @@ static void gt_cpu_config (void)
 }
 
 /*
- * board_pre_init.
+ * board_early_init_f.
  *
  * set up gal. device mappings, etc.
  */
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	uchar sram_boot = 0;
 

board/altera/dk1c20/dk1c20.c

@@ -31,7 +31,7 @@ void _default_hdlr (void)
 	printf ("default_hdlr\n");
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/* init seven segment led display and switch off */
 	sevenseg_set(SEVENSEG_OFF);

board/altera/dk1s10/dk1s10.c

@@ -31,7 +31,7 @@ void _default_hdlr (void)
 	printf ("default_hdlr\n");
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/* init seven segment led display and switch off */
 	sevenseg_set(SEVENSEG_OFF);

board/bubinga405ep/bubinga405ep.c

@@ -26,7 +26,7 @@ long int spd_sdram (void);
 #include <asm/processor.h>
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	mtdcr (uicsr, 0xFFFFFFFF);      /* clear all ints */
 	mtdcr (uicer, 0x00000000);      /* disable all ints */

board/cpc45/cpc45.c

@@ -32,7 +32,7 @@ extern void Plx9030Init(void);
 	/* We have to clear the initial data area here. Couldn't have done it
 	 * earlier because DRAM had not been initialized.
 	 */
-int board_pre_init(void)
+int board_early_init_f(void)
 {
 
 	/* enable DUAL UART Mode on CPC45 */

board/cradle/cradle.c

@@ -170,7 +170,7 @@ init_sio (int led, unsigned long base)
 
 int
 /**********************************************************/
-board_post_init (void)
+board_late_init (void)
 /**********************************************************/
 {
 	return (0);

board/cray/L1/L1.c

@@ -109,7 +109,7 @@ extern char bootscript[];
 static void init_sdram (void);
 
 /* ------------------------------------------------------------------------- */
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/* Running from ROM: global data is still READONLY */
 	init_sdram ();

board/dave/PPChameleonEVB/PPChameleonEVB.c

@@ -51,7 +51,7 @@ const unsigned char fpgadata[] =
 int gunzip(void *, int, unsigned char *, int *);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	out32(GPIO0_OR, CFG_NAND0_CE);                 /* set initial outputs     */
 	out32(GPIO0_OR, CFG_NAND1_CE);                 /* set initial outputs     */

board/ebony/ebony.c

@@ -32,7 +32,7 @@
 
 long int fixed_sdram (void);
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	uint reg;
 	unsigned char *fpga_base = (unsigned char *) CFG_FPGA_BASE;

board/eltec/mhpc/mhpc.c

@@ -104,7 +104,7 @@ static const unsigned int sdram_table[] =
 
 /* ------------------------------------------------------------------------- */
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
     volatile immap_t  *im = (immap_t *)CFG_IMMR;
     volatile cpm8xx_t *cp = &(im->im_cpm);

board/ep8260/ep8260.c

@@ -188,7 +188,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
  * Setup CS4 to enable the Board Control/Status registers.
  * Otherwise the smcs won't work.
 */
-int board_pre_init (void)
+int board_early_init_f (void)
 {
     volatile t_ep_regs *regs = (t_ep_regs*)CFG_REGS_BASE;
     volatile immap_t *immap  = (immap_t *)CFG_IMMR;

board/eric/eric.c

@@ -31,7 +31,7 @@
 #define IBM405GP_GPIO0_ODR     0xef600718	/* GPIO Open Drain */
 #define IBM405GP_GPIO0_IR      0xef60071c	/* GPIO Input */
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 
    /*-------------------------------------------------------------------------+

board/esd/adciop/adciop.c

@@ -31,7 +31,7 @@
 /* ------------------------------------------------------------------------- */
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * Set port pin in escc2 to keep living, and configure user led output

board/esd/ar405/ar405.c

@@ -46,7 +46,7 @@ const unsigned char fpgadata[] = {
 #include "../common/fpga.c"
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 

board/esd/ash405/ash405.c

@@ -50,7 +50,7 @@ const unsigned char fpgadata[] =
 int gunzip(void *, int, unsigned char *, int *);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/esd/canbt/canbt.c

@@ -48,7 +48,7 @@ const unsigned char fpgadata[] = {
 #include "../common/fpga.c"
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 

board/esd/cpci405/cpci405.c

@@ -57,7 +57,7 @@ int cpci405_version(void);
 int gunzip(void *, int, unsigned char *, int *);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 #ifndef CONFIG_CPCI405_VER2
 	int index, len, i;

board/esd/cpci440/cpci440.c

@@ -28,7 +28,7 @@
 
 long int fixed_sdram( void );
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	uint reg;
 

board/esd/cpciiser4/cpciiser4.c

@@ -52,7 +52,7 @@ const unsigned char fpgadata[] = {
 #include "../common/fpga.c"
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 

board/esd/dasa_sim/dasa_sim.c

@@ -137,7 +137,7 @@ static int fpgaBoot (void)
 }
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * Init pci regs

board/esd/dp405/dp405.c

@@ -35,7 +35,7 @@ const unsigned char fpgadata[] =
 int filesize = sizeof(fpgadata);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/esd/du405/du405.c

@@ -53,7 +53,7 @@ const unsigned char fpgadata[] = {
 #include "../common/fpga.c"
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 

board/esd/hub405/hub405.c

@@ -29,7 +29,7 @@
 /* ------------------------------------------------------------------------- */
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/esd/ocrtc/ocrtc.c

@@ -29,7 +29,7 @@
 
 /* ------------------------------------------------------------------------- */
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/esd/pci405/pci405.c

@@ -53,7 +53,7 @@ const unsigned char fpgadata[] =
 int gunzip(void *, int, unsigned char *, int *);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	unsigned long cntrl0Reg;
 

board/esd/plu405/plu405.c

@@ -50,7 +50,7 @@ const unsigned char fpgadata[] =
 int gunzip(void *, int, unsigned char *, int *);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/esd/pmc405/pmc405.c

@@ -35,7 +35,7 @@ const unsigned char fpgadata[] =
 int filesize = sizeof(fpgadata);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/esd/voh405/voh405.c

@@ -50,7 +50,7 @@ const unsigned char fpgadata[] =
 int gunzip(void *, int, unsigned char *, int *);
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/evb64260/bootseq.txt

@@ -58,7 +58,7 @@ in_flash:
     call cpu_init_f
     	debug leds
     board_init_f: (common/board.c)
-	board_pre_init:
+	board_early_init_f:
 	    remap gt regs?
 	    map PCI mem/io
 	    map device space

board/evb64260/evb64260.c

@@ -57,7 +57,7 @@ extern void zuma_mbox_init(void);
 
 /* Unfortunately, we cant change it while we are in flash, so we initialize it
  * to the "final" value. This means that any debug_led calls before
- * board_pre_init wont work right (like in cpu_init_f).
+ * board_early_init_f wont work right (like in cpu_init_f).
  * See also my_remap_gt_regs below. (NTL)
  */
 
@@ -182,11 +182,11 @@ gt_cpu_config(void)
 }
 
 /*
- * board_pre_init.
+ * board_early_init_f.
  *
  * set up gal. device mappings, etc.
  */
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	uchar sram_boot = 0;
 

board/exbitgen/exbitgen.c

@@ -4,7 +4,7 @@
 #include "exbitgen.h"
 
 /* ************************************************************************ */
-int board_pre_init (void)
+int board_early_init_f (void)
 /* ------------------------------------------------------------------------ --
  * Purpose     :
  * Remarks     :

board/ip860/ip860.c

@@ -85,7 +85,7 @@ const uint sdram_table[] = {
 
 
 /* ------------------------------------------------------------------------- */
-int board_pre_init(void)
+int board_early_init_f(void)
 {
     volatile immap_t     *immap  = (immap_t *)CFG_IMMR;
     volatile memctl8xx_t *memctl = &immap->im_memctl;

board/ixdp425/ixdp425.c

@@ -40,7 +40,7 @@
 
 int
 /**********************************************************/
-board_post_init (void)
+board_late_init (void)
 /**********************************************************/
 {
 	return (0);

board/lubbock/lubbock.c

@@ -50,10 +50,10 @@ int board_init (void)
 	return 0;
 }
 
-int board_post_init(void)
+int board_late_init(void)
 {
-   setenv("stdout", "serial");
-   setenv("stderr", "serial");
+	setenv("stdout", "serial");
+	setenv("stderr", "serial");
 	return 0;
 }
 
@@ -71,5 +71,5 @@ int dram_init (void)
 	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
 	gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
 
-   return 0;
+	return 0;
 }

board/lwmon/flash.c

@@ -47,6 +47,9 @@ flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
  */
 static ulong flash_get_size (vu_long *addr, flash_info_t *info);
 static int write_data (flash_info_t *info, ulong dest, ulong data);
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+static int write_data_buf (flash_info_t * info, ulong dest, uchar * cp, int len);
+#endif
 static void flash_get_offsets (ulong base, flash_info_t *info);
 
 /*-----------------------------------------------------------------------
@@ -480,6 +483,17 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	/*
 	 * handle FLASH_WIDTH aligned part
 	 */
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+	while(cnt >= FLASH_WIDTH) {
+		i = CFG_FLASH_BUFFER_SIZE > cnt ?
+		    (cnt & ~(FLASH_WIDTH - 1)) : CFG_FLASH_BUFFER_SIZE;
+		if((rc = write_data_buf(info, wp, src,i)) != 0)
+			return rc;
+		wp += i;
+		src += i;
+		cnt -=i;
+	}
+#else
 	while (cnt >= FLASH_WIDTH) {
 		data = 0;
 		for (i=0; i<FLASH_WIDTH; ++i) {
@@ -491,6 +505,7 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 		wp  += FLASH_WIDTH;
 		cnt -= FLASH_WIDTH;
 	}
+#endif /* CFG_FLASH_USE_BUFFER_WRITE */
 
 	if (cnt == 0) {
 		return (0);
@@ -511,6 +526,28 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	return (write_data(info, wp, data));
 }
 
+/*-----------------------------------------------------------------------
+ * Check flash status, returns:
+ * 0 - OK
+ * 1 - timeout
+ */
+static int flash_status_check(vu_long *addr, ulong tout, char * prompt)
+{
+	ulong status;
+	ulong start;
+
+	/* Wait for command completion */
+	start = get_timer (0);
+	while(((status = *addr) & 0x00800080) != 0x00800080) {
+		if (get_timer(start) > tout) {
+			printf("Flash %s timeout at address %p\n", prompt, addr);
+			*addr = 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+	return 0;
+}
+
 /*-----------------------------------------------------------------------
  * Write a word to Flash, returns:
  * 0 - OK
@@ -520,8 +557,6 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 static int write_data (flash_info_t *info, ulong dest, ulong data)
 {
 	vu_long *addr = (vu_long *)dest;
-	ulong status;
-	ulong start;
 	int flag;
 
 	/* Check if Flash is (sufficiently) erased */
@@ -538,13 +573,8 @@ static int write_data (flash_info_t *info, ulong dest, ulong data)
 	if (flag)
 		enable_interrupts();
 
-	start = get_timer (0);
-
-	while (((status = *addr) & 0x00800080) != 0x00800080) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-			*addr = 0x00FF00FF;	/* restore read mode */
-			return (1);
-		}
+	if (flash_status_check(addr, CFG_FLASH_WRITE_TOUT, "write") != 0) {
+		return (1);
 	}
 
 	*addr = 0x00FF00FF;	/* restore read mode */
@@ -552,5 +582,46 @@ static int write_data (flash_info_t *info, ulong dest, ulong data)
 	return (0);
 }
 
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+/*-----------------------------------------------------------------------
+ * Write a buffer to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ */
+static int write_data_buf(flash_info_t * info, ulong dest, uchar * cp, int len)
+{
+	vu_long *addr = (vu_long *)dest;
+	int sector;
+	int cnt;
+	int retcode;
+	vu_long * src = (vu_long *)cp;
+	vu_long * dst = (vu_long *)dest;
+
+	/* find sector */
+	for(sector = info->sector_count - 1; sector >= 0; sector--) {
+		if(dest >= info->start[sector])
+			break;
+	}
+
+	*addr = 0x00500050;		/* clear status */
+	*addr = 0x00e800e8;		/* write buffer */
+
+	if((retcode = flash_status_check(addr, CFG_FLASH_BUFFER_WRITE_TOUT,
+					 "write to buffer")) == 0) {
+		cnt = len / FLASH_WIDTH;
+		*addr = (cnt-1) | ((cnt-1) << 16);
+		while(cnt-- > 0) {
+			*dst++ = *src++;
+		}
+		*addr = 0x00d000d0;		/* write buffer confirm */
+		retcode = flash_status_check(addr, CFG_FLASH_BUFFER_WRITE_TOUT,
+						 "buffer write");
+	}
+	*addr = 0x00FF00FF;	/* restore read mode */
+	*addr = 0x00500050;	/* clear status */
+	return retcode;
+}
+#endif /* CFG_USE_FLASH_BUFFER_WRITE */
+
 /*-----------------------------------------------------------------------
  */

board/lwmon/lwmon.c

@@ -339,14 +339,14 @@ static long int dram_size (long int mamr_value, long int *base, long int maxsize
 #endif
 
 /***********************************************************************
-F* Function:     int board_pre_init (void) P*A*Z*
+F* Function:     int board_early_init_f (void) P*A*Z*
  *
 P* Parameters:   none
 P*
 P* Returnvalue:  int
 P*                - 0 is always returned.
  *
-Z* Intention:    This function is the board_pre_init() method implementation
+Z* Intention:    This function is the board_early_init_f() method implementation
 Z*               for the lwmon board.
 Z*               Disable Ethernet TENA on Port B.
  *
@@ -354,7 +354,7 @@ D* Design:       wd@denx.de
 C* Coding:       wd@denx.de
 V* Verification: dzu@denx.de
  ***********************************************************************/
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	volatile immap_t *immr = (immap_t *) CFG_IMMR;
 

board/ml2/ml2.c

@@ -22,7 +22,7 @@
 #include <asm/processor.h>
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	return 0;
 }

board/mpc8260ads/mpc8260ads.c

@@ -225,7 +225,7 @@ void reset_phy (void)
 #endif /* CONFIG_MII */
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	vu_long *bcsr = (vu_long *)CFG_BCSR;
 

board/mpc8266ads/mpc8266ads.c

@@ -232,7 +232,7 @@ void reset_phy(void)
 }
 
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
     volatile bcsr_t  *bcsr         = (bcsr_t *)CFG_BCSR;
     volatile pci_ic_t *pci_ic      = (pci_ic_t *) CFG_PCI_INT;

board/mpc8540ads/mpc8540ads.c

@@ -47,7 +47,7 @@ typedef struct bscr_ {
 } bcsr_t;
 #endif
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 #if defined(CONFIG_PCI)
     volatile immap_t *immr = (immap_t *)CFG_IMMR;

board/mpc8560ads/mpc8560ads.c

@@ -199,7 +199,7 @@ typedef struct bscr_ {
 	volatile unsigned char bcsr5;
 } bcsr_t;
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 #if defined(CONFIG_PCI)
     volatile immap_t *immr = (immap_t *)CFG_IMMR;

board/mpl/mip405/mip405.c

@@ -469,7 +469,7 @@ int init_sdram (void)
 	return (0);
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	init_sdram ();
 

board/mpl/pip405/pip405.c

@@ -176,7 +176,7 @@ void write_4hex (unsigned long val)
 
 #endif
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	unsigned char dataout[1];
 	unsigned char datain[128];

board/netvia/netvia.c

@@ -356,7 +356,7 @@ int misc_init_r(void)
 #error Unknown NETVIA board version.
 #endif
 
-int board_pre_init(void)
+int board_early_init_f(void)
 {
 	volatile immap_t *immap = (immap_t *) CFG_IMMR;
 	volatile iop8xx_t *ioport = &immap->im_ioport;

board/oxc/oxc.c

@@ -87,7 +87,7 @@ void pci_init_board (void)
 	pci_mpc824x_init(&hose);
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	*(volatile unsigned char *)(CFG_CPLD_RESET) = 0x89;
 	return 0;

board/pcippc2/pcippc2.c

@@ -75,7 +75,7 @@ int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	return (-1);
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	out32 (REG (CPC0, RSTR), 0xC0000000);
 	iobarrier_rw ();

board/rpxsuper/rpxsuper.c

@@ -191,7 +191,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
  * Setup CS4 to enable the Board Control/Status registers.
  * Otherwise the smcs won't work.
 */
-int board_pre_init (void)
+int board_early_init_f (void)
 {
     volatile t_rpx_regs *regs = (t_rpx_regs*)CFG_REGS_BASE;
     volatile immap_t *immap  = (immap_t *)CFG_IMMR;

board/siemens/IAD210/IAD210.c

@@ -228,7 +228,7 @@ void board_ether_init (void)
 	iop->iop_pdpar |= 0x0080;	/* set pin as MII_clock */
 }
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 	volatile immap_t *immap = (immap_t *) CFG_IMMR;
 	volatile cpmtimer8xx_t *timers = &immap->im_cpmtimer;

board/tqm8xx/tqm8xx.c

@@ -419,6 +419,14 @@ struct serial_state rs_table[] = {
 	{ BASE_BAUD, 6,  (void*)0xec160000 },
 	{ BASE_BAUD, 10, (void*)0xec170000 },
 };
+
+#ifdef CONFIG_BOARD_EARLY_INIT_R
+int board_early_init_r (void)
+{
+	ps2mult_early_init();
+	return (0);
+}
+#endif
 #endif /* CONFIG_BMS2003 */
 
 #endif /* CONFIG_PS2MULT */

board/w7o/w7o.c

@@ -41,7 +41,7 @@ unsigned long get_dram_size (void);
 
 /* ------------------------------------------------------------------------- */
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
 #if defined(CONFIG_W7OLMG)
 	/*

board/walnut405/walnut405.c

@@ -26,7 +26,7 @@
 #include <asm/processor.h>
 #include <spd_sdram.h>
 
-int board_pre_init (void)
+int board_early_init_f (void)
 {
    /*-------------------------------------------------------------------------+
    | Interrupt controller setup for the Walnut board.

cpu/74xx_7xx/start.S

@@ -267,7 +267,7 @@ in_flash:
 	 * everything is write-through.
 	 * The init-mem BAT can be reused after reloc. The old
 	 * gt-regs BAT can be reused after board_init_f calls
-	 * board_pre_init (EVB only).
+	 * board_early_init_f (EVB only).
 	 */
 #if !defined(CONFIG_BAB7xx) && !defined(CONFIG_ELPPC)
 	/* enable address translation */

cpu/mpc8xx/spi.c

@@ -503,8 +503,7 @@ static int packet_check (char * packet, int length)
 	char c = (char) length;
 	int i;
 
-	for (i = 0; i < length; i++)
-	{
+	for (i = 0; i < length; i++) {
 	    if (packet[i] != c++) return -1;
 	}
 
@@ -513,37 +512,32 @@ static int packet_check (char * packet, int length)
 
 int spi_post_test (int flags)
 {
-	DECLARE_GLOBAL_DATA_PTR;
-
 	int res = -1;
 	volatile immap_t *immr = (immap_t *) CFG_IMMR;
-	volatile cpm8xx_t *cp = (cpm8xx_t *) &immr->im_cpm;
+	volatile cpm8xx_t *cp = (cpm8xx_t *) & immr->im_cpm;
 	int i;
 	int l;
 
-	spi_init_f();
-	spi_init_r();
+	spi_init_f ();
+	spi_init_r ();
 
 	cp->cp_spmode |= SPMODE_LOOP;
 
-	for (i = 0; i < TEST_NUM; i++)
-	{
-	    for (l = TEST_MIN_LENGTH; l <= TEST_MAX_LENGTH; l += 8)
-	    {
-		packet_fill(txbuf, l);
+	for (i = 0; i < TEST_NUM; i++) {
+		for (l = TEST_MIN_LENGTH; l <= TEST_MAX_LENGTH; l += 8) {
+			packet_fill (txbuf, l);
 
-		spi_xfer(l);
+			spi_xfer (l);
 
-		if (packet_check(rxbuf, l) < 0)
-		{
-		    goto Done;
+			if (packet_check (rxbuf, l) < 0) {
+				goto Done;
+			}
 		}
-	    }
 	}
 
 	res = 0;
 
-	Done:
+      Done:
 
 	cp->cp_spmode &= ~SPMODE_LOOP;
 
@@ -554,16 +548,11 @@ int spi_post_test (int flags)
 	 */
 
 #if defined(CONFIG_8xx_CONS_SCC2)
-	serial_init();
+	serial_init ();
 #endif
 
-#if defined(SCC_ENET) && (SCC_ENET == 1)
-	eth_init(gd->bd);
-#endif
-
-	if (res != 0)
-	{
-		post_log("SPI test failed\n");
+	if (res != 0) {
+		post_log ("SPI test failed\n");
 	}
 
 	return res;

drivers/keyboard.c

@@ -194,8 +194,14 @@ void handle_scancode(unsigned char scancode)
 	case 0xBA: /* caps lock released */
 		return; /* just swallow */
 	}
+#if 0
 	if((scancode&0x80)==0x80) /* key released */
 		return;
+#else
+	if((scancode&0x80)==0x00) /* key pressed */
+		return;
+	scancode &= ~0x80;
+#endif
 	/* now, decide which table we need */
 	if(scancode > (sizeof(kbd_plain_xlate)/sizeof(kbd_plain_xlate[0]))) { /* scancode not in list */
 		PRINTF("unkown scancode %X\n",scancode);

drivers/ps2mult.c

@@ -42,6 +42,7 @@
 #endif
 
 
+static ulong start_time;
 static int init_done = 0;
 
 static int received_escape = 0;
@@ -63,6 +64,13 @@ static int ps2mult_buf_out_idx;
 
 static u_char ps2mult_buf_status [PS2BUF_SIZE];
 
+#ifndef CONFIG_BOARD_EARLY_INIT_R
+#error #define CONFIG_BOARD_EARLY_INIT_R and call ps2mult_early_init() in board_early_init_r()
+#endif
+void ps2mult_early_init (void)
+{
+	start_time = get_timer(0);
+}
 
 static void ps2mult_send_byte(u_char byte, u_char sel)
 {
@@ -360,6 +368,8 @@ int ps2mult_init (void)
 	int kbd_found = 0;
 	int mouse_found = 0;
 
+	while (get_timer(start_time) < CONFIG_PS2MULT_DELAY);
+
 	ps2ser_init();
 
 	ps2ser_putc(PS2MULT_SESSION_START);

include/common.h

@@ -285,9 +285,10 @@ void  perform_soft_reset(void);
 void	load_sernum_ethaddr (void);
 
 /* $(BOARD)/$(BOARD).c */
-int board_pre_init (void);
-int board_post_init (void);
+int board_early_init_f (void);
+int board_late_init (void);
 int board_postclk_init (void); /* after clocks/timebase, before env/serial */
+int board_early_init_r (void);
 void board_poweroff (void);
 
 #if defined(CFG_DRAM_TEST)

include/configs/ADCIOP.h

@@ -12,7 +12,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -34,27 +34,27 @@
  */
 
 #define CONFIG_IOP480		1	/* This is a IOP480 CPU		*/
-#define CONFIG_ADCIOP		1	/* ...on a ADCIOP board 	*/
+#define CONFIG_ADCIOP		1	/* ...on a ADCIOP board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
 
-#define CONFIG_CPUCLOCK	        66
-#define CONFIG_BUSCLOCK	        (CONFIG_CPUCLOCK)
+#define CONFIG_CPUCLOCK		66
+#define CONFIG_BUSCLOCK		(CONFIG_CPUCLOCK)
 
-#define CONFIG_BAUDRATE	        9600
+#define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
 #define CONFIG_BOOTCOMMAND	"bootm ffc00000" /* autoboot command	*/
 
-#undef  CONFIG_BOOTARGS
+#undef	CONFIG_BOOTARGS
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_IPADDR		10.0.18.222
 #define CONFIG_SERVERIP		10.0.18.190
@@ -62,7 +62,7 @@
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_DHCP	| \
 				CFG_CMD_IRQ	| \
-				CFG_CMD_ELF     | \
+				CFG_CMD_ELF	| \
 				CFG_CMD_ASKENV	)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -74,33 +74,33 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 }
 
-#define CFG_LOAD_ADDR	0x100000	/* default load address	*/
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM                   */
+#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM			*/
 #define CFG_INIT_RAM_END	0x0f00	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -122,28 +122,28 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256     /* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned char   /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x0AA9  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x0556  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned char	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x0AA9	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x0556	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0002  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0000  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0004  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0002	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0000	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0004	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 1 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
@@ -159,8 +159,8 @@
 
 #else /* Use FLASH for environment variables */
 
-#define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector */
 #define CFG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
 
 #define CFG_ENV_SECT_SIZE	0x8000	/* see README - env sector total size	*/
@@ -173,12 +173,12 @@
 #define CONFIG_PCI			/* include pci support			*/
 #undef CONFIG_PCI_PNP
 
-#define CONFIG_NET_MULTI		/* Multi ethernet cards support 	*/
+#define CONFIG_NET_MULTI		/* Multi ethernet cards support		*/
 
 #define CONFIG_TULIP
 
-#define CFG_ETH_DEV_FN       0x0000
-#define CFG_ETH_IOBASE       0x0fff0000
+#define CFG_ETH_DEV_FN	     0x0000
+#define CFG_ETH_IOBASE	     0x0fff0000
 
 /*-----------------------------------------------------------------------
  * Cache Configuration

include/configs/AR405.h

@@ -34,12 +34,12 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405GP CPU	*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_AR405		1	/* ...on a AR405 board	        */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_AR405		1	/* ...on a AR405 board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -51,8 +51,8 @@
 #endif
 
 #if 0
-#define CONFIG_BOOTARGS		"root=/dev/nfs "                        \
-    "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "        \
+#define CONFIG_BOOTARGS		"root=/dev/nfs "			\
+    "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "	\
     "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
 #else
 #define CONFIG_BOOTARGS		"root=/dev/hda1 "			\
@@ -64,7 +64,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_PCI	| \
@@ -76,7 +76,7 @@
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -84,30 +84,30 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define CFG_EXT_SERIAL_CLOCK    14745600 /* use external serial clock   */
+#define CFG_EXT_SERIAL_CLOCK	14745600 /* use external serial clock	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -115,27 +115,27 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
 
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_FORCE	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
 
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
 
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
 
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0403  /* PCI Device ID: ARISTO405     */
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0x80000001      /* 2GB, enable hard-wired to 1  */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xfff00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xfff00001      /* 1MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0403	/* PCI Device ID: ARISTO405	*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0x80000001	/* 2GB, enable hard-wired to 1	*/
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xfff00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xfff00001	/* 1MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -163,24 +163,24 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector */
 #define CFG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
 
-#define CFG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
+#define CFG_ENV_SECT_SIZE	0x10000 /* see README - env sector total size	*/
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
@@ -204,40 +204,40 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (CAN0, 1, 2, 3) initialization                                 */
-#define CFG_EBC_PB1AP           0x01000380  /* enable Ready, BEM=0              */
-#define CFG_EBC_PB1CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 1 (CAN0, 1, 2, 3) initialization					*/
+#define CFG_EBC_PB1AP		0x01000380  /* enable Ready, BEM=0		*/
+#define CFG_EBC_PB1CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 2 (Expension Bus) initialization                                 */
-#define CFG_EBC_PB2AP           0x01000280  /* disable Ready, BEM=0             */
-#define CFG_EBC_PB2CR           0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 2 (Expension Bus) initialization					*/
+#define CFG_EBC_PB2AP		0x01000280  /* disable Ready, BEM=0		*/
+#define CFG_EBC_PB2CR		0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (16552) initialization                                         */
-#define CFG_EBC_PB3AP           0x01000380  /* enable Ready, BEM=0              */
-#define CFG_EBC_PB3CR           0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 3 (16552) initialization						*/
+#define CFG_EBC_PB3AP		0x01000380  /* enable Ready, BEM=0		*/
+#define CFG_EBC_PB3CR		0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 4 (FPGA regs) initialization                                     */
-#define CFG_EBC_PB4AP           0x01005380  /* enable Ready, BEM=0              */
-#define CFG_EBC_PB4CR           0xF031C000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=32bit */
+/* Memory Bank 4 (FPGA regs) initialization					*/
+#define CFG_EBC_PB4AP		0x01005380  /* enable Ready, BEM=0		*/
+#define CFG_EBC_PB4CR		0xF031C000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=32bit */
 
-/* Memory Bank 5 (Flash Bank 1/DUMMY) initialization                            */
-#define CFG_EBC_PB5AP           0x92015480
-#define CFG_EBC_PB5CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 5 (Flash Bank 1/DUMMY) initialization				*/
+#define CFG_EBC_PB5AP		0x92015480
+#define CFG_EBC_PB5CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
-#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
+#define CFG_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
 
-#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
-#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
+#define CFG_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*
  * Internal Definitions

include/configs/ASH405.h

@@ -34,13 +34,13 @@
  */
 
 #define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_ASH405		1	/* ...on a ASH405 board 	*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_ASH405		1	/* ...on a ASH405 board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
-#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
+#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
-#define CONFIG_SYS_CLK_FREQ     33333334 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33333334 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -60,7 +60,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_DHCP	| \
@@ -71,17 +71,17 @@
 				CFG_CMD_I2C	| \
 				CFG_CMD_MII	| \
 				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address         */
+#define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -91,45 +91,45 @@
 
 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
-#undef  CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
+#undef	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 /*-----------------------------------------------------------------------
  * NAND-FLASH stuff
@@ -142,14 +142,14 @@
 #define ADDR_PAGE 2
 #define ADDR_COLUMN_PAGE 3
 
-#define NAND_ChipID_UNKNOWN 	0x00
+#define NAND_ChipID_UNKNOWN	0x00
 #define NAND_MAX_FLOORS 1
 #define NAND_MAX_CHIPS 1
 
-#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
+#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
 
 #define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
 #define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
@@ -168,26 +168,26 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
-#undef  CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_HOST	/* select pci host function	*/
+#undef	CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#undef	CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -215,34 +215,34 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
 #endif
 
 /*-----------------------------------------------------------------------
  * Environment Variable setup
  */
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 
 #define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
-#define CFG_NVRAM_SIZE		242		        /* NVRAM size		*/
+#define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
@@ -252,20 +252,20 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
-					/* have only 8kB, 16kB is save here     */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's	*/
+					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
@@ -283,49 +283,49 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
-#define CFG_EBC_PB0AP           0x92015480
-/*#define CFG_EBC_PB0AP           0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
+#define CFG_EBC_PB0AP		0x92015480
+/*#define CFG_EBC_PB0AP		  0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization			*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
-#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization		*/
+#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization     */
-#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization	*/
+#define CFG_EBC_PB3AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR		0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 
-#define CAN_BA          0xF0000000          /* CAN Base Address                 */
-#define DUART0_BA       0xF0000400          /* DUART Base Address               */
-#define DUART1_BA       0xF0000408          /* DUART Base Address               */
-#define DUART2_BA       0xF0000410          /* DUART Base Address               */
-#define DUART3_BA       0xF0000418          /* DUART Base Address               */
-#define RTC_BA          0xF0000500          /* RTC Base Address                 */
-#define CFG_NAND_BASE   0xF4000000
+#define CAN_BA		0xF0000000	    /* CAN Base Address			*/
+#define DUART0_BA	0xF0000400	    /* DUART Base Address		*/
+#define DUART1_BA	0xF0000408	    /* DUART Base Address		*/
+#define DUART2_BA	0xF0000410	    /* DUART Base Address		*/
+#define DUART3_BA	0xF0000418	    /* DUART Base Address		*/
+#define RTC_BA		0xF0000500	    /* RTC Base Address			*/
+#define CFG_NAND_BASE	0xF4000000
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
-#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
-#define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S50E*/
+#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
-#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+#define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input)     */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CFG_TEMP_STACK_OCM	  1
 
 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
@@ -335,13 +335,13 @@
 
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Definitions for GPIO setup (PPC405EP specific)
  *
- * GPIO0[0]     - External Bus Controller BLAST output
- * GPIO0[1-9]   - Instruction trace outputs -> GPIO
+ * GPIO0[0]	- External Bus Controller BLAST output
+ * GPIO0[1-9]	- Instruction trace outputs -> GPIO
  * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
  * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
  * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -349,15 +349,15 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CFG_GPIO0_OSRH          0x40000550
-#define CFG_GPIO0_OSRL          0x00000110
-#define CFG_GPIO0_ISR1H         0x00000000
-#define CFG_GPIO0_ISR1L         0x15555445
-#define CFG_GPIO0_TSRH          0x00000000
-#define CFG_GPIO0_TSRL          0x00000000
-#define CFG_GPIO0_TCR           0xF7FE0014
+#define CFG_GPIO0_OSRH		0x40000550
+#define CFG_GPIO0_OSRL		0x00000110
+#define CFG_GPIO0_ISR1H		0x00000000
+#define CFG_GPIO0_ISR1L		0x15555445
+#define CFG_GPIO0_TSRH		0x00000000
+#define CFG_GPIO0_TSRL		0x00000000
+#define CFG_GPIO0_TCR		0xF7FE0014
 
-#define CFG_DUART_RST           (0x80000000 >> 14)
+#define CFG_DUART_RST		(0x80000000 >> 14)
 
 /*
  * Internal Definitions
@@ -372,16 +372,16 @@
  * This value will be set if iic boot eprom is disabled.
  */
 #if 0
-#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
 #endif
 #if 1
-#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
 #endif
 #if 0
-#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
 #endif
 
 #endif	/* __CONFIG_H */

include/configs/AmigaOneG3SE.h

@@ -43,7 +43,7 @@
 
 #define CONFIG_AMIGAONEG3SE	1
 
-#define CONFIG_BOARD_PRE_INIT	1
+#define CONFIG_BOARD_EARLY_INIT_F 1
 #define CONFIG_MISC_INIT_R	1
 
 #define CONFIG_VERY_BIG_RAM	1

include/configs/BMW.h

@@ -45,7 +45,9 @@
 #define CONFIG_MPC8245		1
 #define CONFIG_BMW		1
 
-#define CONFIG_BCM570x		1 /* Use Broadcom BCM570x Ethernet Driver */
+#define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()			*/
+
+#define CONFIG_BCM570x		1	/* Use Broadcom BCM570x Ethernet Driver */
 #define	CONFIG_TIGON3		1
 
 #define CONFIG_CONS_INDEX	1

include/configs/BUBINGA405EP.h

@@ -42,7 +42,7 @@
 #define CONFIG_4xx		1	/* ...member of PPC4xx family   */
 #define CONFIG_BUBINGA405EP	1	/* ...on a BUBINGA405EP board	*/
 
-#define CONFIG_BOARD_PRE_INIT	1	/* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 #define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */
 

include/configs/CANBT.h

@@ -34,12 +34,12 @@
  */
 
 #define CONFIG_405CR		1	/* This is a PPC405CR CPU	*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_CANBT		1	/* ...on a CANBT board	        */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_CANBT		1	/* ...on a CANBT board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     25000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	25000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		115200
 #define CONFIG_BOOTDELAY	1	/* autoboot after 1 seconds	*/
@@ -52,13 +52,13 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#undef  CONFIG_PCI_PNP			/* no pci plug-and-play		*/
+#undef	CONFIG_PCI_PNP			/* no pci plug-and-play		*/
 
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
-#define CONFIG_COMMANDS	     (( CONFIG_CMD_DFL	|       \
-				CFG_CMD_IRQ	|       \
-				CFG_CMD_EEPROM      ) & \
+#define CONFIG_COMMANDS	     (( CONFIG_CMD_DFL	|	\
+				CFG_CMD_IRQ	|	\
+				CFG_CMD_EEPROM	    ) & \
 			       ~CFG_CMD_NET)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -66,7 +66,7 @@
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -74,30 +74,30 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define CFG_EXT_SERIAL_CLOCK    14745600 /* use external serial clock   */
+#define CFG_EXT_SERIAL_CLOCK	14745600 /* use external serial clock	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -127,44 +127,44 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 0 /* Use FLASH for environment variables */
 
-#define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector */
 #define CFG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
 
-#define CFG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
+#define CFG_ENV_SECT_SIZE	0x10000 /* see README - env sector total size	*/
 
 #else /* Use EEPROM for environment variables */
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x400   /* 1024 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x400	/* 1024 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 #endif
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
-#define CONFIG_HARD_I2C                 /* I2C with hardware support */
+#define CONFIG_HARD_I2C			/* I2C with hardware support */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* bytes of address		*/
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 
@@ -190,26 +190,26 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (CAN/USB) initialization                                       */
-#define CFG_EBC_PB1AP           0x010053C0  /* enable Ready, BEM=1              */
-#define CFG_EBC_PB1CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 1 (CAN/USB) initialization					*/
+#define CFG_EBC_PB1AP		0x010053C0  /* enable Ready, BEM=1		*/
+#define CFG_EBC_PB1CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 2 (Misc-IO/LEDs) initialization                                  */
-#define CFG_EBC_PB2AP           0x000004c0  /* no Ready, BEM=1                  */
-#define CFG_EBC_PB2CR           0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 2 (Misc-IO/LEDs) initialization					*/
+#define CFG_EBC_PB2AP		0x000004c0  /* no Ready, BEM=1			*/
+#define CFG_EBC_PB2CR		0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (CAN Features) initialization                                  */
-#define CFG_EBC_PB3AP           0x80000040  /* no Ready, BEM=1                  */
-#define CFG_EBC_PB3CR           0xF021C000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=32bit */
+/* Memory Bank 3 (CAN Features) initialization					*/
+#define CFG_EBC_PB3AP		0x80000040  /* no Ready, BEM=1			*/
+#define CFG_EBC_PB3CR		0xF021C000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=32bit */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in RAM)
  */
-#define CFG_INIT_RAM_ADDR	0x00ef0000 /* inside of SDRAM                   */
+#define CFG_INIT_RAM_ADDR	0x00ef0000 /* inside of SDRAM			*/
 #define CFG_INIT_RAM_END	0x0f00	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)

include/configs/CPCI405.h

@@ -34,21 +34,21 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_CPCI405		1	/* ...on a CPCI405 board	*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
 
 #if 0
-#define CONFIG_PREBOOT                                                          \
-	"crc32 f0207004 ffc 0;"                                                 \
-	"if cmp 0 f0207000 1;"                                                  \
-	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"             \
+#define CONFIG_PREBOOT								\
+	"crc32 f0207004 ffc 0;"							\
+	"if cmp 0 f0207000 1;"							\
+	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"		\
 	"else;echo Old CRC is bad;fi"
 #endif
 
@@ -67,9 +67,9 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
-#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT | \
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
 				 CONFIG_BOOTP_DNS | \
 				 CONFIG_BOOTP_DNS2 | \
 				 CONFIG_BOOTP_SEND_HOSTNAME )
@@ -81,7 +81,7 @@
 				CFG_CMD_IDE	| \
 				CFG_CMD_ELF	| \
 				CFG_CMD_MII	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -89,9 +89,9 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -101,38 +101,38 @@
 
 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -140,46 +140,46 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A    */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A	*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * IDE/ATA stuff
  *-----------------------------------------------------------------------
  */
-#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
-#undef  CONFIG_IDE_RESET                /* no reset for ide supported   */
+#undef	CONFIG_IDE_8xx_DIRECT		    /* no pcmcia interface required */
+#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
+#undef	CONFIG_IDE_RESET		/* no reset for ide supported	*/
 
-#define	CFG_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
-#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
 
-#define	CFG_ATA_BASE_ADDR	0xF0100000
-#define	CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_BASE_ADDR	0xF0100000
+#define CFG_ATA_IDE0_OFFSET	0x0000
 
 #define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
-#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
 #define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
 
 /*-----------------------------------------------------------------------
@@ -208,18 +208,18 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 1 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
@@ -235,9 +235,9 @@
 
 #else /* Use EEPROM for environment variables */
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x200   /* 512 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x200	/* 512 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 #endif
 
@@ -249,12 +249,12 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
@@ -280,55 +280,55 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1) initialization                                  */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization					*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization                        */
-#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization			*/
+#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (CompactFlash IDE) initialization                              */
-#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization				*/
+#define CFG_EBC_PB3AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR		0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 4 (NVRAM) initialization                                         */
-#define CFG_EBC_PB4AP           0x01005280  /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1     */
-#define CFG_EBC_PB4CR           0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 4 (NVRAM) initialization						*/
+#define CFG_EBC_PB4AP		0x01005280  /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1	*/
+#define CFG_EBC_PB4CR		0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 5 (Quart) initialization                                         */
-#define CFG_EBC_PB5AP           0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR           0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 5 (Quart) initialization						*/
+#define CFG_EBC_PB5AP		0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR		0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit	*/
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CFG_FPGA_INIT           0x00400000  /* FPGA init pin (ppc input)     */
-#define CFG_FPGA_DONE           0x00800000  /* FPGA done pin (ppc input)     */
+#define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT		0x00400000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE		0x00800000  /* FPGA done pin (ppc input)     */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
 #if 1 /* test-only */
-#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
+#define CFG_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
 
-#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
+#define CFG_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
 #else
-#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM                   */
+#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM			*/
 #endif
-#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 
 /*

include/configs/CPCI4052.h

@@ -34,22 +34,22 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_CPCI405		1	/* ...on a CPCI405 board	*/
-#define CONFIG_CPCI405_VER2     1       /* ...version 2                 */
+#define CONFIG_CPCI405_VER2	1	/* ...version 2			*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
 
 #if 0
-#define CONFIG_PREBOOT                                                          \
-	"crc32 f0207004 ffc 0;"                                                 \
-	"if cmp 0 f0207000 1;"                                                  \
-	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"             \
+#define CONFIG_PREBOOT								\
+	"crc32 f0207004 ffc 0;"							\
+	"if cmp 0 f0207000 1;"							\
+	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"		\
 	"else;echo Old CRC is bad;fi"
 #endif
 
@@ -68,11 +68,11 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 
-#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT | \
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
 				 CONFIG_BOOTP_DNS | \
 				 CONFIG_BOOTP_DNS2 | \
 				 CONFIG_BOOTP_SEND_HOSTNAME )
@@ -88,7 +88,7 @@
 				CFG_CMD_I2C	| \
 				CFG_CMD_MII	| \
 				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -96,9 +96,9 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -108,89 +108,89 @@
 
 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A    */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A	*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * IDE/ATA stuff
  *-----------------------------------------------------------------------
  */
-#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
+#undef	CONFIG_IDE_8xx_DIRECT		    /* no pcmcia interface required */
+#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
 #define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
 
-#define	CFG_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
-#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
 
-#define	CFG_ATA_BASE_ADDR	0xF0100000
-#define	CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_BASE_ADDR	0xF0100000
+#define CFG_ATA_IDE0_OFFSET	0x0000
 
 #define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
-#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
 #define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
 
 /*-----------------------------------------------------------------------
@@ -219,21 +219,21 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
 
 #if 0 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
@@ -246,9 +246,9 @@
 
 #else /* Use EEPROM for environment variables */
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x800   /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 #endif
 
@@ -264,20 +264,20 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
-					/* have only 8kB, 16kB is save here     */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's	*/
+					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
@@ -296,89 +296,89 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1) initialization                                  */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization					*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 2 (CAN0, 1) initialization                                       */
-#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
-#define CFG_LED_ADDR            0xF0000380
+/* Memory Bank 2 (CAN0, 1) initialization					*/
+#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
+#define CFG_LED_ADDR		0xF0000380
 
-/* Memory Bank 3 (CompactFlash IDE) initialization                              */
-#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization				*/
+#define CFG_EBC_PB3AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR		0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 4 (NVRAM/RTC) initialization                                     */
-/*#define CFG_EBC_PB4AP           0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1     */
-#define CFG_EBC_PB4AP           0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1     */
-#define CFG_EBC_PB4CR           0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 4 (NVRAM/RTC) initialization					*/
+/*#define CFG_EBC_PB4AP		  0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1	   */
+#define CFG_EBC_PB4AP		0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1	*/
+#define CFG_EBC_PB4CR		0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 5 (optional Quart) initialization                                */
-#define CFG_EBC_PB5AP           0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR           0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 5 (optional Quart) initialization				*/
+#define CFG_EBC_PB5AP		0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR		0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 6 (FPGA internal) initialization                                 */
-#define CFG_EBC_PB6AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB6CR           0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CFG_FPGA_BASE_ADDR      0xF0400000
+/* Memory Bank 6 (FPGA internal) initialization					*/
+#define CFG_EBC_PB6AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR		0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_FPGA_BASE_ADDR	0xF0400000
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
 /* FPGA internal regs */
-#define CFG_FPGA_MODE           0x00
-#define CFG_FPGA_STATUS         0x02
-#define CFG_FPGA_TS             0x04
-#define CFG_FPGA_TS_LOW         0x06
-#define CFG_FPGA_TS_CAP0        0x10
-#define CFG_FPGA_TS_CAP0_LOW    0x12
-#define CFG_FPGA_TS_CAP1        0x14
-#define CFG_FPGA_TS_CAP1_LOW    0x16
-#define CFG_FPGA_TS_CAP2        0x18
-#define CFG_FPGA_TS_CAP2_LOW    0x1a
-#define CFG_FPGA_TS_CAP3        0x1c
-#define CFG_FPGA_TS_CAP3_LOW    0x1e
+#define CFG_FPGA_MODE		0x00
+#define CFG_FPGA_STATUS		0x02
+#define CFG_FPGA_TS		0x04
+#define CFG_FPGA_TS_LOW		0x06
+#define CFG_FPGA_TS_CAP0	0x10
+#define CFG_FPGA_TS_CAP0_LOW	0x12
+#define CFG_FPGA_TS_CAP1	0x14
+#define CFG_FPGA_TS_CAP1_LOW	0x16
+#define CFG_FPGA_TS_CAP2	0x18
+#define CFG_FPGA_TS_CAP2_LOW	0x1a
+#define CFG_FPGA_TS_CAP3	0x1c
+#define CFG_FPGA_TS_CAP3_LOW	0x1e
 
 /* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET      0x0001
+#define CFG_FPGA_MODE_CF_RESET	    0x0001
 #define CFG_FPGA_MODE_DUART_RESET   0x0002
 #define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004     /* only set on CPCI-405 Ver 3 */
 #define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
 #define CFG_FPGA_MODE_TS_IRQ_CLEAR  0x1000
-#define CFG_FPGA_MODE_TS_CLEAR      0x2000
+#define CFG_FPGA_MODE_TS_CLEAR	    0x2000
 
 /* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0    0x0001
-#define CFG_FPGA_STATUS_DIP1    0x0002
-#define CFG_FPGA_STATUS_DIP2    0x0004
-#define CFG_FPGA_STATUS_FLASH   0x0008
-#define CFG_FPGA_STATUS_TS_IRQ  0x1000
+#define CFG_FPGA_STATUS_DIP0	0x0001
+#define CFG_FPGA_STATUS_DIP1	0x0002
+#define CFG_FPGA_STATUS_DIP2	0x0004
+#define CFG_FPGA_STATUS_FLASH	0x0008
+#define CFG_FPGA_STATUS_TS_IRQ	0x1000
 
-#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
-#define CFG_FPGA_MAX_SIZE       32*1024     /* 32kByte is enough for XC2S15  */
+#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE	32*1024	    /* 32kByte is enough for XC2S15  */
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
-#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+#define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input)     */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
-#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
+#define CFG_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
 
-#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
-#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
+#define CFG_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 
 /*

include/configs/CPCI405AB.h

@@ -34,38 +34,38 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_CPCI405		1	/* ...on a CPCI405 board	*/
-#define CONFIG_CPCI405_VER2     1       /* ...version 2                 */
-#define CONFIG_CPCI405AB        1       /* ...and special AB version    */
+#define CONFIG_CPCI405_VER2	1	/* ...version 2			*/
+#define CONFIG_CPCI405AB	1	/* ...and special AB version	*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
 
 #if 0
-#define CONFIG_PREBOOT                                                          \
-	"crc32 f0207004 ffc 0;"                                                 \
-	"if cmp 0 f0207000 1;"                                                  \
-	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"             \
+#define CONFIG_PREBOOT								\
+	"crc32 f0207004 ffc 0;"							\
+	"if cmp 0 f0207000 1;"							\
+	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"		\
 	"else;echo Old CRC is bad;fi"
 #endif
 
 #undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* default boot command	*/
+#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* default boot command */
 
-#undef  CONFIG_LOADS_ECHO		/* echo on for serial download	*/
+#undef	CONFIG_LOADS_ECHO		/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 
-#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT | \
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
 				 CONFIG_BOOTP_DNS | \
 				 CONFIG_BOOTP_DNS2 | \
 				 CONFIG_BOOTP_SEND_HOSTNAME )
@@ -81,7 +81,7 @@
 				CFG_CMD_I2C	| \
 				CFG_CMD_MII	| \
 				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -89,9 +89,9 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -101,89 +101,89 @@
 
 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A    */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A	*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * IDE/ATA stuff
  *-----------------------------------------------------------------------
  */
-#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
+#undef	CONFIG_IDE_8xx_DIRECT		    /* no pcmcia interface required */
+#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
 #define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
 
-#define	CFG_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
-#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
 
-#define	CFG_ATA_BASE_ADDR	0xF0100000
-#define	CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_BASE_ADDR	0xF0100000
+#define CFG_ATA_IDE0_OFFSET	0x0000
 
 #define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
-#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
 #define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
 
 /*-----------------------------------------------------------------------
@@ -212,21 +212,21 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC32) for environment
@@ -236,20 +236,20 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC32		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
 #define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
 					/* 32 byte page write mode using*/
-					/* last	5 bits of the address	*/
+					/* last 5 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /* Use EEPROM for environment variables */
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x800   /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC32 is 4096 bytes */
 
 #define CFG_NVRAM_BASE_ADDR	0xf0200000		/* NVRAM base address	*/
@@ -259,8 +259,8 @@
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
-					/* have only 8kB, 16kB is save here     */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's	*/
+					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
@@ -279,89 +279,89 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1) initialization                                  */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization					*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 2 (CAN0, 1) initialization                                       */
-#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
-#define CFG_LED_ADDR            0xF0000380
+/* Memory Bank 2 (CAN0, 1) initialization					*/
+#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
+#define CFG_LED_ADDR		0xF0000380
 
-/* Memory Bank 3 (CompactFlash IDE) initialization                              */
-#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization				*/
+#define CFG_EBC_PB3AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR		0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 4 (NVRAM/RTC) initialization                                     */
-/*#define CFG_EBC_PB4AP           0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1     */
-#define CFG_EBC_PB4AP           0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1     */
-#define CFG_EBC_PB4CR           0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 4 (NVRAM/RTC) initialization					*/
+/*#define CFG_EBC_PB4AP		  0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1	   */
+#define CFG_EBC_PB4AP		0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1	*/
+#define CFG_EBC_PB4CR		0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 5 (optional Quart) initialization                                */
-#define CFG_EBC_PB5AP           0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR           0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 5 (optional Quart) initialization				*/
+#define CFG_EBC_PB5AP		0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR		0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 6 (FPGA internal) initialization                                 */
-#define CFG_EBC_PB6AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB6CR           0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CFG_FPGA_BASE_ADDR      0xF0400000
+/* Memory Bank 6 (FPGA internal) initialization					*/
+#define CFG_EBC_PB6AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR		0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_FPGA_BASE_ADDR	0xF0400000
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
 /* FPGA internal regs */
-#define CFG_FPGA_MODE           0x00
-#define CFG_FPGA_STATUS         0x02
-#define CFG_FPGA_TS             0x04
-#define CFG_FPGA_TS_LOW         0x06
-#define CFG_FPGA_TS_CAP0        0x10
-#define CFG_FPGA_TS_CAP0_LOW    0x12
-#define CFG_FPGA_TS_CAP1        0x14
-#define CFG_FPGA_TS_CAP1_LOW    0x16
-#define CFG_FPGA_TS_CAP2        0x18
-#define CFG_FPGA_TS_CAP2_LOW    0x1a
-#define CFG_FPGA_TS_CAP3        0x1c
-#define CFG_FPGA_TS_CAP3_LOW    0x1e
+#define CFG_FPGA_MODE		0x00
+#define CFG_FPGA_STATUS		0x02
+#define CFG_FPGA_TS		0x04
+#define CFG_FPGA_TS_LOW		0x06
+#define CFG_FPGA_TS_CAP0	0x10
+#define CFG_FPGA_TS_CAP0_LOW	0x12
+#define CFG_FPGA_TS_CAP1	0x14
+#define CFG_FPGA_TS_CAP1_LOW	0x16
+#define CFG_FPGA_TS_CAP2	0x18
+#define CFG_FPGA_TS_CAP2_LOW	0x1a
+#define CFG_FPGA_TS_CAP3	0x1c
+#define CFG_FPGA_TS_CAP3_LOW	0x1e
 
 /* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET      0x0001
+#define CFG_FPGA_MODE_CF_RESET	    0x0001
 #define CFG_FPGA_MODE_DUART_RESET   0x0002
 #define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004     /* only set on CPCI-405 Ver 3 */
 #define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
 #define CFG_FPGA_MODE_TS_IRQ_CLEAR  0x1000
-#define CFG_FPGA_MODE_TS_CLEAR      0x2000
+#define CFG_FPGA_MODE_TS_CLEAR	    0x2000
 
 /* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0    0x0001
-#define CFG_FPGA_STATUS_DIP1    0x0002
-#define CFG_FPGA_STATUS_DIP2    0x0004
-#define CFG_FPGA_STATUS_FLASH   0x0008
-#define CFG_FPGA_STATUS_TS_IRQ  0x1000
+#define CFG_FPGA_STATUS_DIP0	0x0001
+#define CFG_FPGA_STATUS_DIP1	0x0002
+#define CFG_FPGA_STATUS_DIP2	0x0004
+#define CFG_FPGA_STATUS_FLASH	0x0008
+#define CFG_FPGA_STATUS_TS_IRQ	0x1000
 
-#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
-#define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S30 */
+#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S30 */
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
-#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+#define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input)     */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
-#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
+#define CFG_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
 
-#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
-#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
+#define CFG_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 
 /*

include/configs/CPCI440.h

@@ -33,7 +33,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_EBONY		1	    /* Board is ebony		*/
 #define CONFIG_4xx		1	    /* ... PPC4xx family	*/
-#define CONFIG_BOARD_PRE_INIT	1	    /* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
 #undef	CFG_DRAM_TEST			    /* Disable-takes long time! */
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 

include/configs/CPCIISER4.h

@@ -34,12 +34,12 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_CPCIISER4	1	/* ...on a CPCIISER4 board	*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     25000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	25000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -51,21 +51,21 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_PCI	| \
 				CFG_CMD_IRQ	| \
 				CFG_CMD_MII	| \
 				CFG_CMD_ELF	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -73,30 +73,30 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define CFG_EXT_SERIAL_CLOCK    1843200  /* use external serial clock   */
+#define CFG_EXT_SERIAL_CLOCK	1843200	 /* use external serial clock	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -104,23 +104,23 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0404  /* PCI Device ID: CPCI-ISER4    */
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xff000001      /* 16MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffe00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffe00001      /* 2MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0404	/* PCI Device ID: CPCI-ISER4	*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xff000001	/* 16MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffe00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffe00001	/* 2MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -148,18 +148,18 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
@@ -169,18 +169,18 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x300   /* 768 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x300	/* 768 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 
 /*-----------------------------------------------------------------------
@@ -205,31 +205,31 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Uart 8bit) initialization                                     */
-#define CFG_EBC_PB1AP           0x01000480  /* TWT=2,TH=2,no Ready,BEM=0,SOR=1  */
-#define CFG_EBC_PB1CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 1 (Uart 8bit) initialization					*/
+#define CFG_EBC_PB1AP		0x01000480  /* TWT=2,TH=2,no Ready,BEM=0,SOR=1	*/
+#define CFG_EBC_PB1CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 2 (Uart 32bit) initialization                                    */
-#define CFG_EBC_PB2AP           0x000004c0  /* no Ready, BEM=1                  */
-#define CFG_EBC_PB2CR           0xF011C000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
+/* Memory Bank 2 (Uart 32bit) initialization					*/
+#define CFG_EBC_PB2AP		0x000004c0  /* no Ready, BEM=1			*/
+#define CFG_EBC_PB2CR		0xF011C000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
 
-/* Memory Bank 3 (FPGA Reset) initialization                                    */
-#define CFG_EBC_PB3AP           0x010004C0  /* no Ready, BEM=1                  */
-#define CFG_EBC_PB3CR           0xF021A000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (FPGA Reset) initialization					*/
+#define CFG_EBC_PB3AP		0x010004C0  /* no Ready, BEM=1			*/
+#define CFG_EBC_PB3CR		0xF021A000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
-#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
-#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
+#define CFG_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
+#define CFG_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*
  * Internal Definitions

include/configs/CRAYL1.h

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000, 2001
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  * David Updegraff, Cray, Inc.  dave@cray.com: our 405 is walnut-lite..
  *
@@ -41,7 +41,7 @@
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 #define CONFIG_MII		    1	/* MII PHY management */
 #define	CONFIG_PHY_ADDR		1	/* PHY address; handling of ENET */
-#define CONFIG_BOARD_PRE_INIT 1 /* early setup for 405gp */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* early setup for 405gp */
 #define CONFIG_MISC_INIT_R	1	/* so that a misc_init_r() is called */
 
 /* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to

include/configs/DASA_SIM.h

@@ -12,7 +12,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -34,20 +34,20 @@
  */
 
 #define CONFIG_IOP480		1	/* This is a IOP480 CPU		*/
-#define CONFIG_DASA_SIM		1	/* ...on a DASA_SIM board 	*/
+#define CONFIG_DASA_SIM		1	/* ...on a DASA_SIM board	*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
 
-#define CONFIG_CPUCLOCK	        66
-#define CONFIG_BUSCLOCK	        (CONFIG_CPUCLOCK)
+#define CONFIG_CPUCLOCK		66
+#define CONFIG_BUSCLOCK		(CONFIG_CPUCLOCK)
 
-#define CONFIG_BAUDRATE	        9600
+#define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds	*/
 #define CONFIG_BOOTCOMMAND	"bootm ffe00000" /* autoboot command	*/
 
-#undef  CONFIG_BOOTARGS
+#undef	CONFIG_BOOTARGS
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
@@ -63,16 +63,16 @@
 				CFG_CMD_IRQ	| \
 				CFG_CMD_BSP	| \
 				CFG_CMD_ASKENV	| \
-				CFG_CMD_ELF     )
+				CFG_CMD_ELF	)
 #else
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_BSP     )
+				CFG_CMD_BSP	)
 #endif
 
 #if 0 /* Does not appear to be used?!  If it is used, needs to be fixed */
 #define CONFIG_SOFT_I2C			/* Software I2C support enabled */
 #endif
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
@@ -83,33 +83,33 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 }
 
-#define CFG_LOAD_ADDR	0x100000	/* default load address	*/
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM                   */
+#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM			*/
 #define CFG_INIT_RAM_END	0x0f00	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -131,37 +131,37 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256     /* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned char   /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x0AA9  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x0556  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned char	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x0AA9	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x0556	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0002  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0000  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0004  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0002	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0000	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0004	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector */
 #define CFG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
 
 #if 0
 #define CFG_ENV_SECT_SIZE	0x8000	/* see README - env sector total size	*/
 #else
-#define CFG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
+#define CFG_ENV_SECT_SIZE	0x10000 /* see README - env sector total size	*/
 #endif
 
 /*-----------------------------------------------------------------------
@@ -170,12 +170,12 @@
 #define CONFIG_PCI			/* include pci support			*/
 #undef CONFIG_PCI_PNP
 
-#define CONFIG_NET_MULTI		/* Multi ethernet cards support 	*/
+#define CONFIG_NET_MULTI		/* Multi ethernet cards support		*/
 
 #define CONFIG_TULIP
 
-#define CFG_ETH_DEV_FN       0x0000
-#define CFG_ETH_IOBASE       0x0fff0000
+#define CFG_ETH_DEV_FN	     0x0000
+#define CFG_ETH_IOBASE	     0x0fff0000
 #define CFG_PCI9054_DEV_FN   0x0800
 #define CFG_PCI9054_IOBASE   0x0eff0000
 

include/configs/DB64360.h

@@ -131,7 +131,7 @@ if we use PCI it has its own MAC addr */
 
 /* which initialization functions to call for this board */
 #define CONFIG_MISC_INIT_R     /* initialize the icache L1 */
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
 
 #define CFG_BOARD_NAME		"DB64360"
 #define CONFIG_IDENT_STRING	"Marvell DB64360 (1.1)"

include/configs/DB64460.h

@@ -68,7 +68,7 @@
 
 /* which initialization functions to call for this board */
 #define CONFIG_MISC_INIT_R     /* initialize the icache L1 */
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
 
 #define CFG_BOARD_NAME		"DB64460"
 #define CONFIG_IDENT_STRING	"Marvell DB64460 (1.0)"

include/configs/DK1C20.h

@@ -295,7 +295,7 @@
 #define CONFIG_SYS_CLK_FREQ	CFG_NIOS_CPU_CLK/* 50 MHz core clock	*/
 #define	CFG_HZ			1000		/* 1 msec time tick	*/
 #undef  CFG_CLKS_IN_HZ
-#define	CONFIG_BOARD_PRE_INIT	1	/* enable early board-spec. init*/
+#define	CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/
 
 /*------------------------------------------------------------------------
  * BASE ADDRESSES / SIZE (Flash, SRAM, SDRAM)

include/configs/DK1S10.h

@@ -294,7 +294,7 @@
 #define CONFIG_SYS_CLK_FREQ	CFG_NIOS_CPU_CLK/* 50 MHz core clock	*/
 #define	CFG_HZ			1000		/* 1 msec time tick	*/
 #undef  CFG_CLKS_IN_HZ
-#define	CONFIG_BOARD_PRE_INIT	1	/* enable early board-spec. init*/
+#define	CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/
 
 /*------------------------------------------------------------------------
  * BASE ADDRESSES / SIZE (Flash, SRAM, SDRAM)

include/configs/DP405.h

@@ -34,13 +34,13 @@
  */
 
 #define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_DP405		1	/* ...on a DP405 board 	        */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_DP405		1	/* ...on a DP405 board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
-#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
+#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
-#define CONFIG_SYS_CLK_FREQ     33333334 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33333334 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -60,7 +60,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_BSP	| \
@@ -69,17 +69,17 @@
 				CFG_CMD_ELF	| \
 				CFG_CMD_DATE	| \
 				CFG_CMD_I2C	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address         */
+#define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -89,70 +89,70 @@
 
 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
-#undef  CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
+#undef	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
-#undef  CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_HOST	/* select pci host function	*/
+#undef	CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#undef	CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*
  * For booting Linux, the board info and command line data
@@ -171,22 +171,22 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -209,13 +209,13 @@
 /*-----------------------------------------------------------------------
  * Environment Variable setup
  */
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 
 #define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
-#define CFG_NVRAM_SIZE		242		        /* NVRAM size		*/
+#define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
@@ -225,20 +225,20 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
-					/* have only 8kB, 16kB is save here     */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's	*/
+					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
@@ -248,41 +248,41 @@
  * External Bus Controller (EBC) Setup
  */
 
-#define CAN_BA          0xF0000000          /* CAN Base Address                 */
-#define RTC_BA          0xF0000500          /* RTC Base Address                 */
+#define CAN_BA		0xF0000000	    /* CAN Base Address			*/
+#define RTC_BA		0xF0000500	    /* RTC Base Address			*/
 
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
 #if 0 /* test-only */
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization			*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit	*/
 #endif
 
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
-#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization		*/
+#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
-#define CFG_FPGA_XC95XL         1           /* using Xilinx XC95XL CPLD      */
-#define CFG_FPGA_MAX_SIZE       32*1024     /* 32kByte is enough for CPLD    */
+#define CFG_FPGA_XC95XL		1	    /* using Xilinx XC95XL CPLD	     */
+#define CFG_FPGA_MAX_SIZE	32*1024	    /* 32kByte is enough for CPLD    */
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG            0x04000000  /* JTAG TMS pin (ppc output)     */
-#define CFG_FPGA_CLK            0x02000000  /* JTAG TCK pin (ppc output)     */
-#define CFG_FPGA_DATA           0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
-#define CFG_FPGA_INIT           0x00010000  /* unused (ppc input)            */
-#define CFG_FPGA_DONE           0x00008000  /* JTAG TDI->TDO pin (ppc input) */
+#define CFG_FPGA_PRG		0x04000000  /* JTAG TMS pin (ppc output)     */
+#define CFG_FPGA_CLK		0x02000000  /* JTAG TCK pin (ppc output)     */
+#define CFG_FPGA_DATA		0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
+#define CFG_FPGA_INIT		0x00010000  /* unused (ppc input)	     */
+#define CFG_FPGA_DONE		0x00008000  /* JTAG TDI->TDO pin (ppc input) */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CFG_TEMP_STACK_OCM	  1
 
 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
@@ -292,13 +292,13 @@
 
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Definitions for GPIO setup (PPC405EP specific)
  *
- * GPIO0[0]     - External Bus Controller BLAST output
- * GPIO0[1-9]   - Instruction trace outputs -> GPIO
+ * GPIO0[0]	- External Bus Controller BLAST output
+ * GPIO0[1-9]	- Instruction trace outputs -> GPIO
  * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
  * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
  * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -306,17 +306,17 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-/* GPIO Input:          OSR=00, ISR=00, TSR=00, TCR=0 */
-/* GPIO Output:         OSR=00, ISR=00, TSR=00, TCR=1 */
-/* Alt. Funtion Input:  OSR=00, ISR=01, TSR=00, TCR=0 */
+/* GPIO Input:		OSR=00, ISR=00, TSR=00, TCR=0 */
+/* GPIO Output:		OSR=00, ISR=00, TSR=00, TCR=1 */
+/* Alt. Funtion Input:	OSR=00, ISR=01, TSR=00, TCR=0 */
 /* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
-#define CFG_GPIO0_OSRH          0x40000540  /*  0 ... 15 */
-#define CFG_GPIO0_OSRL          0x00000110  /* 16 ... 31 */
-#define CFG_GPIO0_ISR1H         0x00000000  /*  0 ... 15 */
-#define CFG_GPIO0_ISR1L         0x14000045  /* 16 ... 31 */
-#define CFG_GPIO0_TSRH          0x00000000  /*  0 ... 15 */
-#define CFG_GPIO0_TSRL          0x00000000  /* 16 ... 31 */
-#define CFG_GPIO0_TCR           0xF7FE0014  /*  0 ... 31 */
+#define CFG_GPIO0_OSRH		0x40000540  /*	0 ... 15 */
+#define CFG_GPIO0_OSRL		0x00000110  /* 16 ... 31 */
+#define CFG_GPIO0_ISR1H		0x00000000  /*	0 ... 15 */
+#define CFG_GPIO0_ISR1L		0x14000045  /* 16 ... 31 */
+#define CFG_GPIO0_TSRH		0x00000000  /*	0 ... 15 */
+#define CFG_GPIO0_TSRL		0x00000000  /* 16 ... 31 */
+#define CFG_GPIO0_TCR		0xF7FE0014  /*	0 ... 31 */
 
 /*
  * Internal Definitions
@@ -331,16 +331,16 @@
  * This value will be set if iic boot eprom is disabled.
  */
 #if 0
-#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
 #endif
 #if 0
-#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
 #endif
 #if 1
-#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
 #endif
 
 #endif	/* __CONFIG_H */

include/configs/DU405.h

@@ -34,12 +34,12 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_DU405	        1	/* ...on a DU405 board	        */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_DU405		1	/* ...on a DU405 board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     25000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	25000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -51,7 +51,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_PCI	| \
@@ -59,7 +59,7 @@
 				CFG_CMD_IDE	| \
 				CFG_CMD_ELF	| \
 				CFG_CMD_DATE	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -69,10 +69,10 @@
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define CONFIG_RTC_MC146818             /* BQ3285 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR	 0xF0000080 /* RTC Base Address         */
+#define CONFIG_RTC_MC146818		/* BQ3285 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR	 0xF0000080 /* RTC Base Address		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -80,30 +80,30 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define CFG_EXT_SERIAL_CLOCK    11059200  /* use external serial clock  */
+#define CFG_EXT_SERIAL_CLOCK	11059200  /* use external serial clock	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -111,44 +111,44 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
 
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
 
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
 
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
 
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0404  /* PCI Device ID: CPCI-ISER4    */
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xff000001      /* 16MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffe00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffe00001      /* 2MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0404	/* PCI Device ID: CPCI-ISER4	*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xff000001	/* 16MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffe00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffe00001	/* 2MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * IDE/ATA stuff
  *-----------------------------------------------------------------------
  */
-#undef  CONFIG_IDE_8xx_DIRECT           /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
-#undef  CONFIG_IDE_RESET                /* no reset for ide supported   */
+#undef	CONFIG_IDE_8xx_DIRECT		/* no pcmcia interface required */
+#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
+#undef	CONFIG_IDE_RESET		/* no reset for ide supported	*/
 
-#define	CFG_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
-#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
 
-#define	CFG_ATA_BASE_ADDR	0xF0100000
-#define	CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_BASE_ADDR	0xF0100000
+#define CFG_ATA_IDE0_OFFSET	0x0000
 
 #define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
-#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
 #define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
 
 /*-----------------------------------------------------------------------
@@ -177,18 +177,18 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
@@ -198,18 +198,18 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x400   /* 1024 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x400	/* 1024 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 
 /*-----------------------------------------------------------------------
@@ -234,48 +234,48 @@
  * External Bus Controller (EBC) Setup
  */
 
-#define FLASH0_BA       0xFFC00000          /* FLASH 0 Base Address             */
-#define FLASH1_BA       0xFF800000          /* FLASH 1 Base Address             */
-#define CAN_BA          0xF0000000          /* CAN Base Address                 */
-#define DUART_BA        0xF0300000          /* DUART Base Address               */
-#define CF_BA           0xF0100000          /* CompactFlash Base Address        */
-#define SRAM_BA         0xF0200000          /* SRAM Base Address                */
-#define DURAG_IO_BA     0xF0400000          /* DURAG Bus IO Base Address        */
-#define DURAG_MEM_BA    0xF0500000          /* DURAG Bus Mem Base Address       */
+#define FLASH0_BA	0xFFC00000	    /* FLASH 0 Base Address		*/
+#define FLASH1_BA	0xFF800000	    /* FLASH 1 Base Address		*/
+#define CAN_BA		0xF0000000	    /* CAN Base Address			*/
+#define DUART_BA	0xF0300000	    /* DUART Base Address		*/
+#define CF_BA		0xF0100000	    /* CompactFlash Base Address	*/
+#define SRAM_BA		0xF0200000	    /* SRAM Base Address		*/
+#define DURAG_IO_BA	0xF0400000	    /* DURAG Bus IO Base Address	*/
+#define DURAG_MEM_BA	0xF0500000	    /* DURAG Bus Mem Base Address	*/
 
-#define FPGA_MODE_REG   (DUART_BA+0x80)     /* FPGA Mode Register               */
+#define FPGA_MODE_REG	(DUART_BA+0x80)	    /* FPGA Mode Register		*/
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP   0x92015480
-#define CFG_EBC_PB0CR   FLASH0_BA | 0x5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP	0x92015480
+#define CFG_EBC_PB0CR	FLASH0_BA | 0x5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1) initialization                                  */
-#define CFG_EBC_PB1AP   0x92015480
-#define CFG_EBC_PB1CR   FLASH1_BA | 0x5A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization					*/
+#define CFG_EBC_PB1AP	0x92015480
+#define CFG_EBC_PB1CR	FLASH1_BA | 0x5A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 2 (CAN0) initialization                                          */
-#define CFG_EBC_PB2AP   0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR   CAN_BA | 0x18000    /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 2 (CAN0) initialization						*/
+#define CFG_EBC_PB2AP	0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR	CAN_BA | 0x18000    /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (DUART) initialization                                         */
-#define CFG_EBC_PB3AP   0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR   DUART_BA | 0x18000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 3 (DUART) initialization						*/
+#define CFG_EBC_PB3AP	0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR	DUART_BA | 0x18000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 4 (CompactFlash IDE) initialization                              */
-#define CFG_EBC_PB4AP   0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB4CR   CF_BA | 0x1A000     /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 4 (CompactFlash IDE) initialization				*/
+#define CFG_EBC_PB4AP	0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB4CR	CF_BA | 0x1A000	    /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 5 (SRAM) initialization                                          */
-#define CFG_EBC_PB5AP   0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB5CR   SRAM_BA | 0x1A000   /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 5 (SRAM) initialization						*/
+#define CFG_EBC_PB5AP	0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB5CR	SRAM_BA | 0x1A000   /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 6 (DURAG Bus IO Space) initialization                            */
-#define CFG_EBC_PB6AP   0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB6CR   DURAG_IO_BA | 0x18000 /* BAS=0xF04,BS=1MB,BU=R/W,BW=8bit*/
+/* Memory Bank 6 (DURAG Bus IO Space) initialization				*/
+#define CFG_EBC_PB6AP	0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR	DURAG_IO_BA | 0x18000 /* BAS=0xF04,BS=1MB,BU=R/W,BW=8bit*/
 
-/* Memory Bank 7 (DURAG Bus Mem Space) initialization                           */
-#define CFG_EBC_PB7AP   0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB7CR   DURAG_MEM_BA | 0x18000 /* BAS=0xF05,BS=1MB,BU=R/W,BW=8bit */
+/* Memory Bank 7 (DURAG Bus Mem Space) initialization				*/
+#define CFG_EBC_PB7AP	0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB7CR	DURAG_MEM_BA | 0x18000 /* BAS=0xF05,BS=1MB,BU=R/W,BW=8bit */
 
 
 /*-----------------------------------------------------------------------
@@ -283,7 +283,7 @@
  */
 
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CFG_TEMP_STACK_OCM	  1
 
 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
@@ -293,7 +293,7 @@
 #define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 
 /*

include/configs/EBONY.h

@@ -32,7 +32,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_EBONY		1	    /* Board is ebony		*/
 #define CONFIG_4xx		1	    /* ... PPC4xx family	*/
-#define CONFIG_BOARD_PRE_INIT	1	    /* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
 #undef	CFG_DRAM_TEST			    /* Disable-takes long time! */
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 

include/configs/ELPT860.h

@@ -19,7 +19,7 @@
 **
 ** This program is distributed in the hope that it will be useful,
 ** but WITHOUT ANY WARRANTY; without even the implied warranty of
-** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 ** GNU General Public License for more details.
 **
 ** You should have received a copy of the GNU General Public License
@@ -47,26 +47,26 @@
 #define CONFIG_MPC860T		1
 #define CONFIG_ELPT860		1	/* ...on a LEOX's ELPT860 CPU board */
 
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		    */
+#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		    */
 #undef	  CONFIG_8xx_CONS_SMC2
 #undef	  CONFIG_8xx_CONS_NONE
 
-#define CONFIG_CLOCKS_IN_MHZ    1  /* Clock passed to Linux (<2.4.5) in MHz */
-#define CONFIG_8xx_GCLK_FREQ    50000000       /* MPC860T runs at 50MHz */
+#define CONFIG_CLOCKS_IN_MHZ	1  /* Clock passed to Linux (<2.4.5) in MHz */
+#define CONFIG_8xx_GCLK_FREQ	50000000       /* MPC860T runs at 50MHz */
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* Call board_pre_init          */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 /* BOOT arguments */
-#define CONFIG_PREBOOT                                                     \
-     "echo;"	                                                           \
-     "echo Type \"run nfsboot\" to mount root filesystem over NFS;"        \
+#define CONFIG_PREBOOT							   \
+     "echo;"								   \
+     "echo Type \"run nfsboot\" to mount root filesystem over NFS;"	   \
      "echo"
 
 #undef	  CONFIG_BOOTARGS
 
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
+#define CONFIG_EXTRA_ENV_SETTINGS					\
     "ramargs=setenv bootargs root=/dev/ram rw\0"			\
     "rootargs=setenv rootpath /tftp/$(ipaddr)\0"			\
     "nfsargs=setenv bootargs root=/dev/nfs rw "				\
@@ -86,14 +86,14 @@
 #undef	  CONFIG_WATCHDOG		/* watchdog disabled		*/
 #undef	  CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 #undef	  CONFIG_RTC_MPC8xx		/* internal RTC MPC8xx unused	*/
-#define CONFIG_RTC_DS164x       1       /* RTC is a Dallas DS1646       */
+#define CONFIG_RTC_DS164x	1	/* RTC is a Dallas DS1646	*/
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #undef	  CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
 
-#define CONFIG_COMMANDS	        ( CONFIG_CMD_DFL | \
+#define CONFIG_COMMANDS		( CONFIG_CMD_DFL | \
 				  CFG_CMD_ASKENV | \
-				  CFG_CMD_DATE   )
+				  CFG_CMD_DATE	 )
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
@@ -101,8 +101,8 @@
 /*
  * Miscellaneous configurable options
  */
-#define	CFG_LONGHELP			/* undef to save memory		*/
-#define	CFG_PROMPT     "LEOX_elpt860: "	/* Monitor Command Prompt	*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT     "LEOX_elpt860: " /* Monitor Command Prompt	*/
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #  define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
@@ -110,35 +110,35 @@
 #  define CFG_CBSIZE	 256		/* Console I/O Buffer Size	*/
 #endif
 
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS	  16		/* max number of command args	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	  16		/* max number of command args	*/
 #define CFG_BARGSIZE	  CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	0x00400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x00C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define	CFG_LOAD_ADDR		0x00100000	/* default load address	*/
+#define CFG_LOAD_ADDR		0x00100000	/* default load address */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 /*
  * Environment Variables and Storages
  */
-#define CONFIG_ENV_OVERWRITE    1  /* Allow Overwrite of serial# & ethaddr */
+#define CONFIG_ENV_OVERWRITE	1  /* Allow Overwrite of serial# & ethaddr */
 
-#undef    CFG_ENV_IS_IN_NVRAM          /* Environment is in NVRAM       */
-#undef    CFG_ENV_IS_IN_EEPROM         /* Environment is in I2C EEPROM  */
-#define CFG_ENV_IS_IN_FLASH     1      /* Environment is in FLASH       */
+#undef	  CFG_ENV_IS_IN_NVRAM	       /* Environment is in NVRAM	*/
+#undef	  CFG_ENV_IS_IN_EEPROM	       /* Environment is in I2C EEPROM	*/
+#define CFG_ENV_IS_IN_FLASH	1      /* Environment is in FLASH	*/
 
-#define CONFIG_BAUDRATE		9600   /* console baudrate = 9600 bps   */
+#define CONFIG_BAUDRATE		9600   /* console baudrate = 9600 bps	*/
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
-#define CONFIG_ETHADDR          00:01:77:00:60:40
-#define CONFIG_IPADDR           192.168.0.30
-#define CONFIG_NETMASK          255.255.255.0
+#define CONFIG_ETHADDR		00:01:77:00:60:40
+#define CONFIG_IPADDR		192.168.0.30
+#define CONFIG_NETMASK		255.255.255.0
 
-#define CONFIG_SERVERIP         192.168.0.1
-#define CONFIG_GATEWAYIP        192.168.0.1
+#define CONFIG_SERVERIP		192.168.0.1
+#define CONFIG_GATEWAYIP	192.168.0.1
 
 /*
  * Low Level Configuration Settings
@@ -155,19 +155,19 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	CFG_IMMR
-#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0x02000000
-#define CFG_NVRAM_BASE          0x03000000
+#define CFG_NVRAM_BASE		0x03000000
 
 #if defined(CFG_ENV_IS_IN_FLASH)
 #  if defined(DEBUG)
@@ -184,48 +184,48 @@
 #endif
 
 #define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define	CFG_MALLOC_LEN		(128 << 10)  /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN		(128 << 10)  /* Reserve 128 kB for malloc() */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define	CFG_BOOTMAPSZ		(8 << 20)    /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(8 << 20)    /* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks        */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks	     */
 #define CFG_MAX_FLASH_SECT	8	/* max number of sectors on one chip */
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)   */
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)   */
 
 #if defined(CFG_ENV_IS_IN_FLASH)
-#  define CFG_ENV_OFFSET        0x10000	/* Offset   of Environment Sector    */
-#  define CFG_ENV_SIZE          0x10000 /* Total Size of Environment Sector  */
+#  define CFG_ENV_OFFSET	0x10000 /* Offset   of Environment Sector    */
+#  define CFG_ENV_SIZE		0x10000 /* Total Size of Environment Sector  */
 #endif
 
 /*-----------------------------------------------------------------------
  * NVRAM organization
  */
-#define CFG_NVRAM_BASE_ADDR     CFG_NVRAM_BASE /* Base address of NVRAM area */
-#define CFG_NVRAM_SIZE          ((128*1024)-8) /* clock regs resident in the */
+#define CFG_NVRAM_BASE_ADDR	CFG_NVRAM_BASE /* Base address of NVRAM area */
+#define CFG_NVRAM_SIZE		((128*1024)-8) /* clock regs resident in the */
 					       /*   8 top NVRAM locations    */
 
 #if defined(CFG_ENV_IS_IN_NVRAM)
-#  define CFG_ENV_ADDR          CFG_NVRAM_BASE /* Base address of NVRAM area */
-#  define CFG_ENV_SIZE          0x4000	/* Total Size of Environment Sector  */
+#  define CFG_ENV_ADDR		CFG_NVRAM_BASE /* Base address of NVRAM area */
+#  define CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector  */
 #endif
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs               */
+#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs		     */
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#  define CFG_CACHELINE_SHIFT	 4      /* log base 2 of the above value     */
+#  define CFG_CACHELINE_SHIFT	 4	/* log base 2 of the above value     */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -235,10 +235,10 @@
  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
  */
 #if defined(CONFIG_WATCHDOG)
-#  define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT  | SYPCR_BME | SYPCR_SWF | \
+#  define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT	 | SYPCR_BME | SYPCR_SWF | \
 			 SYPCR_SWE  | SYPCR_SWRI | SYPCR_SWP)
 #else
-#  define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT  | SYPCR_BME | SYPCR_SWF | \
+#  define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT	 | SYPCR_BME | SYPCR_SWF | \
 						   SYPCR_SWP)
 #endif
 
@@ -309,7 +309,7 @@
  * BR0 and OR0 (FLASH)
  */
 
-#define FLASH_BASE0_PRELIM	CFG_FLASH_BASE	/* FLASH bank #0          */
+#define FLASH_BASE0_PRELIM	CFG_FLASH_BASE	/* FLASH bank #0	  */
 
 /* used to re-map FLASH both when starting from SRAM or FLASH:
  * restrict access enough to keep SRAM working (if any)
@@ -327,10 +327,10 @@
  * BR1 and OR1 (SDRAM)
  *
  */
-#define SDRAM_BASE1_PRELIM	CFG_SDRAM_BASE	/* SDRAM bank #0        */
-#define	SDRAM_MAX_SIZE		0x02000000	/* 32 MB MAX for CS1    */
+#define SDRAM_BASE1_PRELIM	CFG_SDRAM_BASE	/* SDRAM bank #0	*/
+#define SDRAM_MAX_SIZE		0x02000000	/* 32 MB MAX for CS1	*/
 
-/* SDRAM timing:                                                        */
+/* SDRAM timing:							*/
 #define CFG_OR_TIMING_SDRAM	0x00000000
 
 #define CFG_OR1_PRELIM	((2 * CFG_PRELIM_OR_AM) | CFG_OR_TIMING_SDRAM )
@@ -340,10 +340,10 @@
  * BR2 and OR2 (NVRAM)
  *
  */
-#define NVRAM_BASE1_PRELIM	CFG_NVRAM_BASE	/* NVRAM bank #0        */
-#define	NVRAM_MAX_SIZE		0x00020000	/* 128 KB MAX for CS2   */
+#define NVRAM_BASE1_PRELIM	CFG_NVRAM_BASE	/* NVRAM bank #0	*/
+#define NVRAM_MAX_SIZE		0x00020000	/* 128 KB MAX for CS2	*/
 
-#define CFG_OR2_PRELIM	        0xFFF80160
+#define CFG_OR2_PRELIM		0xFFF80160
 #define CFG_BR2_PRELIM	((NVRAM_BASE1_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
 
 /*
@@ -351,15 +351,15 @@
  */
 
 /* periodic timer for refresh */
-#define CFG_MAMR_PTA	        97     /* start with divider for 100 MHz */
+#define CFG_MAMR_PTA		97     /* start with divider for 100 MHz */
 
 /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
 #define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16	  /* setting for 2 banks */
-#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32	  /* setting for 1 bank  */
+#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32	  /* setting for 1 bank	 */
 
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit  */
-#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8    /* setting for 2 banks */
-#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16   /* setting for 1 bank  */
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit	 */
+#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8	  /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16	  /* setting for 1 bank	 */
 
 /*
  * MAMR settings for SDRAM
@@ -383,8 +383,8 @@
 /*
  * Boot Flags
  */
-#define	BOOTFLAG_COLD	0x01             /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02             /* Software reboot                  */
+#define BOOTFLAG_COLD	0x01		 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		 /* Software reboot		     */
 
 
 #endif	/* __CONFIG_H */

include/configs/ERIC.h

@@ -37,7 +37,7 @@
 #define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_ERIC		1	/* ...on a ERIC board	*/
 
-#define	CONFIG_BOARD_PRE_INIT	1	/* run board_pre_init() */
+#define	CONFIG_BOARD_EARLY_INIT_F 1	/* run board_early_init_f() */
 
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/
 

include/configs/EVB64260.h

@@ -51,7 +51,7 @@
 
 /* which initialization functions to call for this board */
 #define CONFIG_MISC_INIT_R	1
-#define CONFIG_BOARD_PRE_INIT	1
+#define CONFIG_BOARD_EARLY_INIT_F 1
 
 #ifndef CONFIG_EVB64260_750CX
 #define CFG_BOARD_NAME		"EVB64260"

include/configs/EXBITGEN.h

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -37,7 +37,7 @@
 #define CONFIG_4xx		1	/* ...member of PPC4xx family   */
 #define CONFIG_EXBITGEN		1	/* on a Exbit Generic board     */
 
-#define CONFIG_BOARD_PRE_INIT	1	/* Call board_pre_init		*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 #define CONFIG_SYS_CLK_FREQ     25000000 /* external frequency to pll   */
 

include/configs/HUB405.h

@@ -34,13 +34,13 @@
  */
 
 #define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_HUB405		1	/* ...on a ASH405 board 	*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_HUB405		1	/* ...on a ASH405 board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
-#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
+#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
-#define CONFIG_SYS_CLK_FREQ     33333334 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33333334 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -60,7 +60,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_DHCP	| \
@@ -70,14 +70,14 @@
 				CFG_CMD_I2C	| \
 				CFG_CMD_MII	| \
 				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -87,45 +87,45 @@
 
 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
-#undef  CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
+#undef	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 /*-----------------------------------------------------------------------
  * NAND-FLASH stuff
@@ -138,14 +138,14 @@
 #define ADDR_PAGE 2
 #define ADDR_COLUMN_PAGE 3
 
-#define NAND_ChipID_UNKNOWN 	0x00
+#define NAND_ChipID_UNKNOWN	0x00
 #define NAND_MAX_FLOORS 1
 #define NAND_MAX_CHIPS 1
 
-#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
+#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
 
 #define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
 #define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
@@ -164,26 +164,26 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#undef  CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
-#undef  CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#undef	CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_HOST	/* select pci host function	*/
+#undef	CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#undef	CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -211,34 +211,34 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
 #endif
 
 /*-----------------------------------------------------------------------
  * Environment Variable setup
  */
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 
 #define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
-#define CFG_NVRAM_SIZE		242		        /* NVRAM size		*/
+#define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
@@ -248,20 +248,20 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
-					/* have only 8kB, 16kB is save here     */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's	*/
+					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
@@ -279,48 +279,48 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
-#define CFG_EBC_PB0AP           0x92015480
-/*#define CFG_EBC_PB0AP           0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
+#define CFG_EBC_PB0AP		0x92015480
+/*#define CFG_EBC_PB0AP		  0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization			*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 2 (8 Bit Peripheral: UART) initialization                        */
+/* Memory Bank 2 (8 Bit Peripheral: UART) initialization			*/
 #if 0
-#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 #else
-#define CFG_EBC_PB2AP           0x92015480
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+#define CFG_EBC_PB2AP		0x92015480
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 #endif
 
-#define DUART0_BA       0xF0000000          /* DUART Base Address               */
-#define DUART1_BA       0xF0000008          /* DUART Base Address               */
-#define DUART2_BA       0xF0000010          /* DUART Base Address               */
-#define DUART3_BA       0xF0000018          /* DUART Base Address               */
-#define CFG_NAND_BASE   0xF4000000
+#define DUART0_BA	0xF0000000	    /* DUART Base Address		*/
+#define DUART1_BA	0xF0000008	    /* DUART Base Address		*/
+#define DUART2_BA	0xF0000010	    /* DUART Base Address		*/
+#define DUART3_BA	0xF0000018	    /* DUART Base Address		*/
+#define CFG_NAND_BASE	0xF4000000
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
-#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
-#define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S50E*/
+#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
-#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+#define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input)     */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CFG_TEMP_STACK_OCM	  1
 
 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
@@ -330,13 +330,13 @@
 
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Definitions for GPIO setup (PPC405EP specific)
  *
- * GPIO0[0]     - External Bus Controller BLAST output
- * GPIO0[1-9]   - Instruction trace outputs -> GPIO
+ * GPIO0[0]	- External Bus Controller BLAST output
+ * GPIO0[1-9]	- Instruction trace outputs -> GPIO
  * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
  * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
  * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
@@ -344,15 +344,15 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CFG_GPIO0_OSRH          0x40000550
-#define CFG_GPIO0_OSRL          0x00000110
-#define CFG_GPIO0_ISR1H         0x00000000
-#define CFG_GPIO0_ISR1L         0x15555445
-#define CFG_GPIO0_TSRH          0x00000000
-#define CFG_GPIO0_TSRL          0x00000000
-#define CFG_GPIO0_TCR           0xF7FE0014
+#define CFG_GPIO0_OSRH		0x40000550
+#define CFG_GPIO0_OSRL		0x00000110
+#define CFG_GPIO0_ISR1H		0x00000000
+#define CFG_GPIO0_ISR1L		0x15555445
+#define CFG_GPIO0_TSRH		0x00000000
+#define CFG_GPIO0_TSRL		0x00000000
+#define CFG_GPIO0_TCR		0xF7FE0014
 
-#define CFG_DUART_RST           (0x80000000 >> 14)
+#define CFG_DUART_RST		(0x80000000 >> 14)
 
 /*
  * Internal Definitions
@@ -367,16 +367,16 @@
  * This value will be set if iic boot eprom is disabled.
  */
 #if 0
-#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
+#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
 #endif
 #if 0
-#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
+#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
 #endif
 #if 1
-#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
+#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
 #endif
 
 #endif	/* __CONFIG_H */

include/configs/IAD210.h

@@ -66,7 +66,7 @@
 #define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
 
 /* using this define saves us updating another source file */
-#define CONFIG_BOARD_PRE_INIT  1
+#define CONFIG_BOARD_EARLY_INIT_F 1
 
 #undef	CONFIG_BOOTARGS
 /* #define CONFIG_BOOTCOMMAND							\

include/configs/IP860.h

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000
+ * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -35,7 +35,7 @@
 
 #define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
 #define CONFIG_IP860		1	/* ...on a IP860 board		*/
-#define CONFIG_BOARD_PRE_INIT	1	    /* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 #define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 #define CONFIG_BAUDRATE		9600

include/configs/MHPC.h

@@ -18,7 +18,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -39,23 +39,23 @@
  * (easy to change)
  */
 #define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
-#define CONFIG_MHPC 		1	/* on a miniHiPerCam	        */
-#define CONFIG_BOARD_PRE_INIT   1       /* do special hardware init.    */
-#define CONFIG_MISC_INIT_R      1
+#define CONFIG_MHPC		1	/* on a miniHiPerCam		*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* do special hardware init.	*/
+#define CONFIG_MISC_INIT_R	1
 
 #define CONFIG_8xx_GCLK_FREQ	MPC8XX_SPEED
 #undef	CONFIG_8xx_CONS_SMC1
-#define	CONFIG_8xx_CONS_SMC2	1	/* Console is on SMC2		*/
+#define CONFIG_8xx_CONS_SMC2	1	/* Console is on SMC2		*/
 #undef	CONFIG_8xx_CONS_NONE
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
 
-#define CONFIG_ENV_OVERWRITE    1
-#define CONFIG_ETHADDR          00:00:5b:ee:de:ad
+#define CONFIG_ENV_OVERWRITE	1
+#define CONFIG_ETHADDR		00:00:5b:ee:de:ad
 
-#undef  CONFIG_BOOTARGS
+#undef	CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND	\
 	"bootp;"								\
 	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
@@ -66,12 +66,12 @@
 #undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
+#define CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
 
-#undef  CONFIG_UCODE_PATCH
+#undef	CONFIG_UCODE_PATCH
 
 /* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
 #define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
 /*
  * Software (bit-bang) I2C driver configuration
@@ -84,36 +84,36 @@
 #define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
 #define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 #define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
 
-#define CFG_I2C_SPEED                   50000
-#define CFG_I2C_SLAVE                   0xFE
-#define CFG_I2C_EEPROM_ADDR             0x50    /* EEPROM X24C04		*/
-#define CFG_I2C_EEPROM_ADDR_LEN         1       /* bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW    0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS      3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS  10
-
-#define LCD_VIDEO_ADDR          (SDRAM_MAX_SIZE-SDRAM_RES_SIZE)
-#define LCD_VIDEO_SIZE          SDRAM_RES_SIZE  /* 2MB */
-#define LCD_VIDEO_COLS          640
-#define LCD_VIDEO_ROWS          480
-#define LCD_VIDEO_FG            255
-#define LCD_VIDEO_BG            0
-
-#undef  CONFIG_VIDEO                            /* test only ! s.a devices.c and 8xx */
-#define CONFIG_CFB_CONSOLE                      /* framebuffer console with std input */
+#define CFG_I2C_SPEED			50000
+#define CFG_I2C_SLAVE			0xFE
+#define CFG_I2C_EEPROM_ADDR		0x50	/* EEPROM X24C04		*/
+#define CFG_I2C_EEPROM_ADDR_LEN		1	/* bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS	3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10
+
+#define LCD_VIDEO_ADDR		(SDRAM_MAX_SIZE-SDRAM_RES_SIZE)
+#define LCD_VIDEO_SIZE		SDRAM_RES_SIZE	/* 2MB */
+#define LCD_VIDEO_COLS		640
+#define LCD_VIDEO_ROWS		480
+#define LCD_VIDEO_FG		255
+#define LCD_VIDEO_BG		0
+
+#undef	CONFIG_VIDEO				/* test only ! s.a devices.c and 8xx */
+#define CONFIG_CFB_CONSOLE			/* framebuffer console with std input */
 #define CONFIG_VIDEO_LOGO
 
-#define VIDEO_KBD_INIT_FCT      0               /* no KBD dev on MHPC - use serial */
-#define VIDEO_TSTC_FCT          serial_tstc
-#define VIDEO_GETC_FCT          serial_getc
+#define VIDEO_KBD_INIT_FCT	0		/* no KBD dev on MHPC - use serial */
+#define VIDEO_TSTC_FCT		serial_tstc
+#define VIDEO_GETC_FCT		serial_getc
 
-#define CONFIG_BR0_WORKAROUND   1
+#define CONFIG_BR0_WORKAROUND	1
 
 #define CONFIG_COMMANDS	     ( CONFIG_CMD_DFL  | \
 			       CFG_CMD_DATE    | \
@@ -131,23 +131,23 @@
 /*
  * Miscellaneous configurable options
  */
-#define	CFG_LONGHELP			/* undef to save memory		*/
-#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define	CFG_LOAD_ADDR		0x300000	/* default load address	*/
+#define CFG_LOAD_ADDR		0x300000	/* default load address */
 
-#define	CFG_HZ                  1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
 
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
@@ -166,33 +166,33 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	CFG_IMMR
-#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define	CFG_GBL_DATA_SIZE       64  /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET     (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xfe000000
 
-#define	CFG_MONITOR_LEN		0x40000 	/* Reserve 256 kB for Monitor	*/
-#undef  CFG_MONITOR_BASE	            /* to run U-Boot from RAM */
+#define CFG_MONITOR_LEN		0x40000		/* Reserve 256 kB for Monitor	*/
+#undef	CFG_MONITOR_BASE		    /* to run U-Boot from RAM */
 #define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /* one flash only */
+#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS	1	    /* one flash only */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map- for Linux	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map- for Linux	*/
 
 /*-----------------------------------------------------------------------
  * FLASH organization
@@ -202,9 +202,9 @@
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-#define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		CFG_MONITOR_LEN	/* Offset of Environment */
-#define	CFG_ENV_SIZE		0x20000	/* Total Size of Environment 	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		CFG_MONITOR_LEN /* Offset of Environment */
+#define CFG_ENV_SIZE		0x20000 /* Total Size of Environment	*/
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
@@ -262,7 +262,7 @@
  * interrupt status bit - leave PLL multiplication factor unchanged !
  */
 #define MPC8XX_SPEED	50000000L
-#define MPC8XX_XIN   	5000000L      /* ref clk */
+#define MPC8XX_XIN	5000000L      /* ref clk */
 #define MPC8XX_FACT	(MPC8XX_SPEED/MPC8XX_XIN)
 #define CFG_PLPRCR	(((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
 			PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
@@ -307,8 +307,8 @@
  * BR1 and OR1 (SDRAM)
  */
 #define SDRAM_BASE1_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_MAX_SIZE		0x01000000	/* max 16 MB    	*/
-#define SDRAM_RES_SIZE          0x00200000      /* 2 MB for framebuffer */
+#define SDRAM_MAX_SIZE		0x01000000	/* max 16 MB		*/
+#define SDRAM_RES_SIZE		0x00200000	/* 2 MB for framebuffer */
 
 /* SDRAM timing: drive GPL5 high on first cycle */
 #define CFG_OR_TIMING_SDRAM	(OR_G5LS)
@@ -358,14 +358,14 @@
  *-----------------------------------------------------------------------
  *
  */
-#define CFG_DER	0
+#define CFG_DER 0
 
 /*
  * Internal Definitions
  *
  * Boot Flags
  */
-#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
 #endif	/* __CONFIG_H */

include/configs/MIP405.h

@@ -252,7 +252,7 @@
 /* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
 #define FLASH_SIZE_PRELIM	 3  /* maximal flash FLASH size bank #0	*/
 
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
 
 /* Peripheral Bus Mapping */
 #define PER_PLD_ADDR		0xF4000000 /* smallest window is 1MByte 0x10 0000*/

include/configs/MPC8260ADS.h

@@ -51,7 +51,7 @@
 #define CONFIG_ADSTYPE		CFG_8260ADS
 #endif /* CONFIG_ADSTYPE */
 
-#define CONFIG_BOARD_PRE_INIT	1	/* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 /* allow serial and ethaddr to be overwritten */
 #define CONFIG_ENV_OVERWRITE

include/configs/MPC8266ADS.h

@@ -49,10 +49,10 @@
  * (easy to change)
  */
 
-#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU   */
-#define CONFIG_MPC8266ADS	1	/* ...on motorola ads board */
+#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU	*/
+#define CONFIG_MPC8266ADS	1	/* ...on motorola ADS board	*/
 
-#define CONFIG_BOARD_PRE_INIT	1	/* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 /* allow serial and ethaddr to be overwritten */
 #define CONFIG_ENV_OVERWRITE

include/configs/MPC8540ADS.h

@@ -31,21 +31,21 @@
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_BOOKE		1	    /* BOOKE 			*/
+#define CONFIG_BOOKE		1	    /* BOOKE			*/
 #define CONFIG_E500		1	    /* BOOKE e500 family	*/
 #define CONFIG_MPC85xx		1	    /* MPC8540/MPC8560		*/
-#define CONFIG_MPC85xx_REV1	1	    /* MPC85xx Rev 1 Chip       */
-#define CONFIG_MPC8540		1	    /* MPC8540 specific	        */
+#define CONFIG_MPC85xx_REV1	1	    /* MPC85xx Rev 1 Chip	*/
+#define CONFIG_MPC8540		1	    /* MPC8540 specific		*/
 #define CONFIG_MPC8540ADS	1	    /* MPC8540ADS board specific*/
 
-#undef  CONFIG_PCI	         	    /* pci ethernet support	*/
-#define CONFIG_TSEC_ENET 		    /* tsec ethernet support  */
+#undef	CONFIG_PCI			    /* pci ethernet support	*/
+#define CONFIG_TSEC_ENET		    /* tsec ethernet support  */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM                   /* Use SPD EEPROM for DDR setup */
-#undef  CONFIG_DDR_ECC			    /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM		    /* Use SPD EEPROM for DDR setup */
+#undef	CONFIG_DDR_ECC			    /* only for ECC DDR module */
 
 #if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
+#define CONFIG_DDR_DLL			    /* possible DLL fix needed */
 #endif
 
 /* Using Localbus SDRAM to emulate flash before we can program the flash,
@@ -53,24 +53,24 @@
  */
 #undef CONFIG_RAM_AS_FLASH
 
-#if !defined(CONFIG_PCI) 		    /* some PCI card is 33Mhz only */
+#if !defined(CONFIG_PCI)		    /* some PCI card is 33Mhz only */
 #define CONFIG_SYS_CLK_FREQ	66000000    /* sysclk for MPC85xx	*/
 #else
 #define CONFIG_SYS_CLK_FREQ	33000000    /* most pci cards are 33Mhz */
 #endif
 
-#if !defined(CONFIG_SPD_EEPROM)             /* manually set up DDR parameters */
+#if !defined(CONFIG_SPD_EEPROM)		    /* manually set up DDR parameters */
 #define CONFIG_DDR_SETTING
 #endif
 
 /* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE		    	    /* toggle L2 cache 	*/
-#undef  CONFIG_BTB			    /* toggle branch predition */
-#undef  CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+#define CONFIG_L2_CACHE			    /* toggle L2 cache	*/
+#undef	CONFIG_BTB			    /* toggle branch predition	*/
+#undef	CONFIG_ADDR_STREAMING		    /* toggle addr streaming	*/
 
-#define CONFIG_BOARD_PRE_INIT	1	    /* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
 
-#undef	CFG_DRAM_TEST			    /* memory test, takes time  */
+#undef	CFG_DRAM_TEST			    /* memory test, takes time	*/
 #define CFG_MEMTEST_START	0x00200000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x00400000
 
@@ -82,13 +82,13 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default	*/
-#define CFG_CCSRBAR		0xfdf00000	/* relocated CCSRBAR 	*/
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default	*/
+#define CFG_CCSRBAR		0xfdf00000	/* relocated CCSRBAR	*/
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory  */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	 */
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE		128             /* DDR is now 128MB     */
+#define CFG_SDRAM_SIZE		128		/* DDR is now 128MB	*/
 
 #if defined(CONFIG_RAM_AS_FLASH)
 #define CFG_LBC_SDRAM_BASE	0xfc000000	/* Localbus SDRAM */
@@ -98,44 +98,44 @@
 #define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB	*/
 
 #if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE    	0xf8000000	/* start of FLASH  16M	*/
+#define CFG_FLASH_BASE		0xf8000000	/* start of FLASH  16M	*/
 #define CFG_BR0_PRELIM		0xf8001801	/* port size 32bit */
 #else /* Boot from real Flash */
-#define CFG_FLASH_BASE		0xff000000	/* start of FLASH 16M    */
+#define CFG_FLASH_BASE		0xff000000	/* start of FLASH 16M	 */
 #define CFG_BR0_PRELIM		0xff001801	/* port size 32bit	*/
 #endif
 
-#define	CFG_OR0_PRELIM		0xff006ff7	/* 16MB Flash		*/
+#define CFG_OR0_PRELIM		0xff006ff7	/* 16MB Flash		*/
 #define CFG_MAX_FLASH_BANKS	1		/* number of banks	*/
-#define CFG_MAX_FLASH_SECT	64		/* sectors per device   */
+#define CFG_MAX_FLASH_SECT	64		/* sectors per device	*/
 #undef	CFG_FLASH_CHECKSUM
 #define CFG_FLASH_ERASE_TOUT	60000	/* Timeout for Flash Erase (in ms)*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)*/
 
-#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
 
 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
 #define CFG_RAMBOOT
 #else
-#undef  CFG_RAMBOOT
+#undef	CFG_RAMBOOT
 #endif
 
 #define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
 
 #if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS        0x00000007      /* 0-128MB              */
-#define CFG_DDR_CS0_CONFIG      0x80000002
-#define CFG_DDR_TIMING_1        0x37344321
-#define CFG_DDR_TIMING_2        0x00000800      /* P9-45,may need tuning*/
-#define CFG_DDR_CONTROL         0xc2000000      /* unbuffered,no DYN_PWR*/
-#define CFG_DDR_MODE            0x00000062      /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL        0x05200100      /* autocharge,no open page*/
+#define CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB		*/
+#define CFG_DDR_CS0_CONFIG	0x80000002
+#define CFG_DDR_TIMING_1	0x37344321
+#define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning*/
+#define CFG_DDR_CONTROL		0xc2000000	/* unbuffered,no DYN_PWR*/
+#define CFG_DDR_MODE		0x00000062	/* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL	0x05200100	/* autocharge,no open page*/
 #endif
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
 /* local bus definitions */
-#define CFG_BR2_PRELIM		0xf8001861	/* 64MB localbus SDRAM  */
+#define CFG_BR2_PRELIM		0xf8001861	/* 64MB localbus SDRAM	*/
 #define CFG_OR2_PRELIM		0xfc006901
 #define CFG_LBC_LCRR		0x00030004	/* local bus freq divider*/
 #define CFG_LBC_LBCR		0x00000000
@@ -148,52 +148,52 @@
 #define CFG_LBC_LSDMR_5		0x4061b723
 
 #if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM          0xf8000801      /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM		0xf8000801	/* 32KB, 8-bit wide for ADS config reg */
 #else
-#define CFG_BR4_PRELIM          0xfc000801      /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM		0xfc000801	/* 32KB, 8-bit wide for ADS config reg */
 #endif
-#define CFG_OR4_PRELIM          0xffffe1f1
-#define CFG_BCSR                (CFG_BR4_PRELIM & 0xffff8000)
+#define CFG_OR4_PRELIM		0xffffe1f1
+#define CFG_BCSR		(CFG_BR4_PRELIM & 0xffff8000)
 
 #define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 	1
-#define CFG_INIT_RAM_ADDR   	0x40000000 	/* Initial RAM address	*/
-#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0x40000000	/* Initial RAM address	*/
+#define CFG_INIT_RAM_END	0x4000		/* End of used area in RAM */
 
-#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX     1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_NS16550
 #define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE    1
+#define CFG_NS16550_REG_SIZE	1
 #define CFG_NS16550_CLK		get_bus_freq(0)
-#define CONFIG_BAUDRATE	 	115200
+#define CONFIG_BAUDRATE		115200
 
 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)
+#define CFG_NS16550_COM1	(CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
 
 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
-#ifdef  CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* I2C */
-#define  CONFIG_HARD_I2C		/* I2C with hardware support*/
+#define	 CONFIG_HARD_I2C		/* I2C with hardware support*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
 
 /* General PCI */
 #define CFG_PCI_MEM_BASE	0xe0000000
@@ -203,22 +203,22 @@
 #define CONFIG_NET_MULTI
 #undef CONFIG_EEPRO100
 #define CONFIG_TULIP
-#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
   #if !defined(CONFIG_PCI_PNP)
-  #define PCI_ENET0_IOADDR      0xe0000000
-  #define PCI_ENET0_MEMADDR     0xe0000000
-  #define PCI_IDSEL_NUMBER      0x0c 	/*slot0->3(IDSEL)=12->15*/
+  #define PCI_ENET0_IOADDR	0xe0000000
+  #define PCI_ENET0_MEMADDR	0xe0000000
+  #define PCI_IDSEL_NUMBER	0x0c	/*slot0->3(IDSEL)=12->15*/
   #endif
-#define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup  */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
+#define CFG_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
 #if defined(CONFIG_MPC85xx_REV1)	/* Errata PCI 8 */
   #define CFG_PCI_SUBSYS_DEVICEID 0x0003
 #else
   #define CFG_PCI_SUBSYS_DEVICEID 0x0008
 #endif
 #elif defined(CONFIG_TSEC_ENET)
-#define CONFIG_NET_MULTI 	1
-#define CONFIG_PHY_M88E1011      1       /* GigaBit Ether PHY    */
+#define CONFIG_NET_MULTI	1
+#define CONFIG_PHY_M88E1011	 1	 /* GigaBit Ether PHY	 */
 #define CONFIG_MII		1	/* MII PHY management	*/
 #define CONFIG_PHY_ADDR		8	/* PHY address	*/
 #endif
@@ -232,7 +232,7 @@
   #else
   #define CFG_ENV_IS_IN_FLASH	1
   #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
-  #define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+  #define CFG_ENV_SECT_SIZE	0x40000 /* 256K(one sector) for env */
   #endif
   #define CFG_ENV_SIZE		0x2000
 #else
@@ -242,10 +242,10 @@
 #define CFG_ENV_SIZE		0x2000
 #endif
 
-#define CONFIG_BOOTARGS	"root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200"
+#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200"
 /*#define CONFIG_BOOTARGS	"root=/dev/ram rw console=ttyS0,115200"*/
 #define CONFIG_BOOTCOMMAND	"bootm 0xff300000 0xff700000"
-#define CONFIG_BOOTDELAY	3 	/* -1 disable autoboot */
+#define CONFIG_BOOTDELAY	3	/* -1 disable autoboot */
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
@@ -274,7 +274,7 @@
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"MPC8540ADS=> "	/* Monitor Command Prompt	*/
+#define CFG_PROMPT	"MPC8540ADS=> " /* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
@@ -291,10 +291,10 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ	(8 << 20) 	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux */
 
 /* Cache Configuration */
-#define CFG_DCACHE_SIZE	32768
+#define CFG_DCACHE_SIZE 32768
 #define CFG_CACHELINE_SIZE	32
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
@@ -315,17 +315,17 @@
 
 /* NOTE: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR  00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR  00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR  00:01:af:07:9b:8c
+#define CONFIG_ETHADDR	00:01:af:07:9b:8a
+#define CONFIG_ETH1ADDR	 00:01:af:07:9b:8b
+#define CONFIG_ETH2ADDR	 00:01:af:07:9b:8c
 #endif
 
-#define CONFIG_SERVERIP         163.12.64.52
-#define CONFIG_IPADDR           10.82.0.105
-#define CONFIG_GATEWAYIP        10.82.1.254
-#define CONFIG_NETMASK          255.255.254.0
-#define CONFIG_HOSTNAME         MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH         /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE         pImage
+#define CONFIG_SERVERIP		163.12.64.52
+#define CONFIG_IPADDR		10.82.0.105
+#define CONFIG_GATEWAYIP	10.82.1.254
+#define CONFIG_NETMASK		255.255.254.0
+#define CONFIG_HOSTNAME		MPC8560ADS_PILOT_003
+#define CONFIG_ROOTPATH		/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
+#define CONFIG_BOOTFILE		pImage
 
 #endif	/* __CONFIG_H */

include/configs/MPC8560ADS.h

@@ -31,22 +31,22 @@
 #define __CONFIG_H
 
 /* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE		*/
-#define CONFIG_E500		1	/* BOOKE e500 family	*/
-#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560	*/
-#define CONFIG_MPC85xx_REV1	1	/* MPC85xx Rev 1.0 chip */
-#define CONFIG_MPC8560		1	/* MPC8560 specific	*/
-#define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific*/
-
-#undef  CONFIG_PCI	         	/* pci ethernet support	*/
-#define CONFIG_TSEC_ENET 		/* tsec ethernet support*/
-#undef  CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
+#define CONFIG_BOOKE		1	/* BOOKE			*/
+#define CONFIG_E500		1	/* BOOKE e500 family		*/
+#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560		*/
+#define CONFIG_MPC85xx_REV1	1	/* MPC85xx Rev 1.0 chip		*/
+#define CONFIG_MPC8560		1	/* MPC8560 specific		*/
+#define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific	*/
+
+#undef	CONFIG_PCI			/* pci ethernet support		*/
+#define CONFIG_TSEC_ENET		/* tsec ethernet support	*/
+#undef	CONFIG_ETHER_ON_FCC		/* cpm FCC ethernet support	*/
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
-#undef  CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#undef	CONFIG_DDR_ECC			/* only for ECC DDR module	*/
 
 #if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL                  /* possible DLL fix needed */
+#define CONFIG_DDR_DLL			/* possible DLL fix needed	*/
 #endif
 
 /* Using Localbus SDRAM to emulate flash before we can program the flash,
@@ -54,10 +54,10 @@
  */
 #undef CONFIG_RAM_AS_FLASH
 
-#if !defined(CONFIG_PCI)		/* some PCI card is 33Mhz only */
-#define CONFIG_SYS_CLK_FREQ	66000000/* sysclk for MPC85xx */
+#if !defined(CONFIG_PCI)		/* some PCI card is 33Mhz only	*/
+#define CONFIG_SYS_CLK_FREQ	66000000/* sysclk for MPC85xx		*/
 #else
-#define CONFIG_SYS_CLK_FREQ     33000000/* most pci cards are 33Mhz */
+#define CONFIG_SYS_CLK_FREQ	33000000/* most pci cards are 33Mhz	*/
 #endif
 
 #if !defined(CONFIG_SPD_EEPROM)		/* manually set up DDR parameters */
@@ -65,15 +65,15 @@
 #endif
 
 /* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE                     /* toggle L2 cache         */
-#undef  CONFIG_BTB                          /* toggle branch predition */
-#undef  CONFIG_ADDR_STREAMING               /* toggle addr streaming   */
+#define CONFIG_L2_CACHE			    /* toggle L2 cache		*/
+#undef	CONFIG_BTB			    /* toggle branch predition	*/
+#undef	CONFIG_ADDR_STREAMING		    /* toggle addr streaming	*/
 
-#define CONFIG_BOARD_PRE_INIT   1           /* Call board_pre_init      */
+#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
 
-#undef  CFG_DRAM_TEST                       /* memory test, takes time  */
-#define CFG_MEMTEST_START       0x00200000  /* memtest region */
-#define CFG_MEMTEST_END         0x00400000
+#undef	CFG_DRAM_TEST			    /* memory test, takes time	*/
+#define CFG_MEMTEST_START	0x00200000  /* memtest region */
+#define CFG_MEMTEST_END		0x00400000
 
 #if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
      defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
@@ -85,48 +85,48 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default	*/
-#define CFG_CCSRBAR             0xfdf00000      /* relocated CCSRBAR    */
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default	*/
+#define CFG_CCSRBAR		0xfdf00000	/* relocated CCSRBAR	*/
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory  */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	 */
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE		128		/* DDR is 128MB	*/
+#define CFG_SDRAM_SIZE		128		/* DDR is 128MB */
 
 #if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_LBC_SDRAM_BASE      0xfc000000      /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_BASE	0xfc000000	/* Localbus SDRAM */
 #else
-#define CFG_LBC_SDRAM_BASE      0xf8000000      /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_BASE	0xf8000000	/* Localbus SDRAM */
 #endif
 #define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB	*/
 
 #if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE        0xf8000000      /* start of FLASH  16M  */
-#define CFG_BR0_PRELIM        0xf8001801      /* port size 32bit */
+#define CFG_FLASH_BASE	      0xf8000000      /* start of FLASH	 16M  */
+#define CFG_BR0_PRELIM	      0xf8001801      /* port size 32bit */
 #else /* Boot from real Flash */
-#define CFG_FLASH_BASE        0xff000000      /* start of FLASH 16M    */
-#define CFG_BR0_PRELIM        0xff001801      /* port size 32bit      */
+#define CFG_FLASH_BASE	      0xff000000      /* start of FLASH 16M    */
+#define CFG_BR0_PRELIM	      0xff001801      /* port size 32bit      */
 #endif
 
-#define CFG_OR0_PRELIM          0xff006ff7      /* 16MB Flash           */
+#define CFG_OR0_PRELIM		0xff006ff7	/* 16MB Flash		*/
 #define CFG_MAX_FLASH_BANKS	1		/* number of banks	*/
-#define CFG_MAX_FLASH_SECT	64		/* sectors per device   */
+#define CFG_MAX_FLASH_SECT	64		/* sectors per device	*/
 #undef	CFG_FLASH_CHECKSUM
 #define CFG_FLASH_ERASE_TOUT	60000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor	*/
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor	*/
 
 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
 #define CFG_RAMBOOT
 #else
-#undef  CFG_RAMBOOT
+#undef	CFG_RAMBOOT
 #endif
 
-#define SPD_EEPROM_ADDRESS 	0x51     	/*  DDR DIMM */
+#define SPD_EEPROM_ADDRESS	0x51		/*  DDR DIMM */
 
 #if defined(CONFIG_DDR_SETTING)
-#define	CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
+#define CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
 #define CFG_DDR_CS0_CONFIG	0x80000002
 #define CFG_DDR_TIMING_1	0x37344321
 #define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning*/
@@ -138,9 +138,9 @@
 #undef CONFIG_CLOCKS_IN_MHZ
 
 /* local bus definitions */
-#define CFG_BR2_PRELIM		0xf8001861	/* 64MB localbus SDRAM  */
+#define CFG_BR2_PRELIM		0xf8001861	/* 64MB localbus SDRAM	*/
 #define CFG_OR2_PRELIM		0xfc006901
-#define CFG_LBC_LCRR		0x00030004	/* local bus freq 	*/
+#define CFG_LBC_LCRR		0x00030004	/* local bus freq	*/
 #define CFG_LBC_LBCR		0x00000000
 #define CFG_LBC_LSRT		0x20000000
 #define CFG_LBC_MRTPR		0x20000000
@@ -151,78 +151,78 @@
 #define CFG_LBC_LSDMR_5		0x4061b723
 
 #if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM          0xf8000801      /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM		0xf8000801	/* 32KB, 8-bit wide for ADS config reg */
 #else
-#define CFG_BR4_PRELIM          0xfc000801      /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM		0xfc000801	/* 32KB, 8-bit wide for ADS config reg */
 #endif
 #define CFG_OR4_PRELIM		0xffffe1f1
 #define CFG_BCSR		(CFG_BR4_PRELIM & 0xffff8000)
 
 #define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 	1
-#define CFG_INIT_RAM_ADDR       0x40000000      /* Initial RAM address  */
-#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0x40000000	/* Initial RAM address	*/
+#define CFG_INIT_RAM_END	0x4000		/* End of used area in RAM */
 
-#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
 
 /* Serial Port */
-#define CONFIG_CONS_ON_SCC              	/* define if console on SCC */
-#undef  CONFIG_CONS_NONE                	/* define if console on something else */
-#define CONFIG_CONS_INDEX       1       	/* which serial channel for console */
+#define CONFIG_CONS_ON_SCC			/* define if console on SCC */
+#undef	CONFIG_CONS_NONE			/* define if console on something else */
+#define CONFIG_CONS_INDEX	1		/* which serial channel for console */
 
-#define CONFIG_BAUDRATE	 	115200
+#define CONFIG_BAUDRATE		115200
 
 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
-#ifdef  CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* I2C */
-#define  CONFIG_HARD_I2C    		/* I2C with hardware support*/
+#define	 CONFIG_HARD_I2C		/* I2C with hardware support*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES        {0x69}  /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
 
 #define CFG_PCI_MEM_BASE	0xe0000000
 #define CFG_PCI_MEM_PHYS	0xe0000000
 #define CFG_PCI_MEM_SIZE	0x10000000
 
-#if defined(CONFIG_PCI) 		/* PCI Ethernet card */
+#if defined(CONFIG_PCI)			/* PCI Ethernet card */
 #define CONFIG_NET_MULTI
 #define CONFIG_EEPRO100
 #undef CONFIG_TULIP
-#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
   #if !defined(CONFIG_PCI_PNP)
-  #define PCI_ENET0_IOADDR    	0xe0000000
-  #define PCI_ENET0_MEMADDR     0xe0000000
-  #define PCI_IDSEL_NUMBER      0x0c 	/* slot0->3(IDSEL)=12->15 */
+  #define PCI_ENET0_IOADDR	0xe0000000
+  #define PCI_ENET0_MEMADDR	0xe0000000
+  #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
   #endif
-#define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup  */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
-#if defined(CONFIG_MPC85xx_REV1) 	/* Errata PCI 7 */
+#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
+#define CFG_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
+#if defined(CONFIG_MPC85xx_REV1)	/* Errata PCI 7 */
   #define CFG_PCI_SUBSYS_DEVICEID 0x0003
 #else
   #define CFG_PCI_SUBSYS_DEVICEID 0x0009
 #endif
-#elif defined(CONFIG_TSEC_ENET) 	/* TSEC Ethernet port */
-#define CONFIG_NET_MULTI 	1
-#define CONFIG_PHY_M88E1011      1       /* GigaBit Ether PHY        */
+#elif defined(CONFIG_TSEC_ENET)		/* TSEC Ethernet port */
+#define CONFIG_NET_MULTI	1
+#define CONFIG_PHY_M88E1011	 1	 /* GigaBit Ether PHY	     */
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		8	/* PHY address			*/
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
-#define CONFIG_ETHER_ON_FCC             /* define if ether on FCC   */
-#undef  CONFIG_ETHER_NONE               /* define if ether on something else */
-#define CONFIG_ETHER_INDEX      2       /* which channel for ether  */
+#define CONFIG_ETHER_ON_FCC		/* define if ether on FCC   */
+#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
+#define CONFIG_ETHER_INDEX	2	/* which channel for ether  */
   #if (CONFIG_ETHER_INDEX == 2)
   /*
    * - Rx-CLK is CLK13
@@ -230,15 +230,15 @@
    * - Select bus for bd/buffers
    * - Full duplex
    */
-  #define CFG_CMXFCR_MASK       (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-  #define CFG_CMXFCR_VALUE      (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-  #define CFG_CPMFCR_RAMTYPE    0
-  #define CFG_FCC_PSMR          (FCC_PSMR_FDE)
+  #define CFG_CMXFCR_MASK	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+  #define CFG_CMXFCR_VALUE	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+  #define CFG_CPMFCR_RAMTYPE	0
+  #define CFG_FCC_PSMR		(FCC_PSMR_FDE)
   #define FETH2_RST		0x01
   #elif (CONFIG_ETHER_INDEX == 3)
   /* need more definitions here for FE3 */
   #define FETH3_RST		0x80
-  #endif  				/* CONFIG_ETHER_INDEX */
+  #endif				/* CONFIG_ETHER_INDEX */
 #define CONFIG_MII			/* MII PHY management */
 #define CONFIG_BITBANGMII		/* bit-bang MII PHY management	*/
 /*
@@ -267,7 +267,7 @@
   #else
   #define CFG_ENV_IS_IN_FLASH	1
   #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
-  #define CFG_ENV_SECT_SIZE	0x40000	/* 128K(one sector) for env */
+  #define CFG_ENV_SECT_SIZE	0x40000 /* 128K(one sector) for env */
   #endif
   #define CFG_ENV_SIZE		0x2000
 #else
@@ -320,7 +320,7 @@
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"MPC8560ADS=> "	/* Monitor Command Prompt	*/
+#define CFG_PROMPT	"MPC8560ADS=> " /* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
@@ -361,17 +361,17 @@
 
 /*Note: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_ETHADDR  00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR  00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR  00:01:af:07:9b:8c
+#define CONFIG_ETHADDR	00:01:af:07:9b:8a
+#define CONFIG_ETH1ADDR	 00:01:af:07:9b:8b
+#define CONFIG_ETH2ADDR	 00:01:af:07:9b:8c
 #endif
 
-#define CONFIG_SERVERIP 	163.12.64.52
-#define CONFIG_IPADDR  		10.82.0.105
+#define CONFIG_SERVERIP		163.12.64.52
+#define CONFIG_IPADDR		10.82.0.105
 #define CONFIG_GATEWAYIP	10.82.1.254
 #define CONFIG_NETMASK		255.255.254.0
-#define CONFIG_HOSTNAME 	MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH 	/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE 	pImage
+#define CONFIG_HOSTNAME		MPC8560ADS_PILOT_003
+#define CONFIG_ROOTPATH		/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
+#define CONFIG_BOOTFILE		pImage
 
 #endif	/* __CONFIG_H */

include/configs/NETVIA.h

@@ -105,7 +105,7 @@
 #define CONFIG_COMMANDS		CONFIG_COMMANDS_BASE
 #endif
 
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
 #define CONFIG_MISC_INIT_R
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */

include/configs/OCRTC.h

@@ -34,12 +34,12 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_OCRTC   		1	/* ...on a OCRTC board	        */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_OCRTC		1	/* ...on a OCRTC board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -51,7 +51,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_PCI	| \
@@ -59,7 +59,7 @@
 				CFG_CMD_ASKENV	| \
 				CFG_CMD_ELF	| \
 				CFG_CMD_BSP	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -67,9 +67,9 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -77,32 +77,32 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -110,28 +110,28 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
 
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
 
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
 
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
 
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0410  /* PCI Device ID: OCRTC         */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0410	/* PCI Device ID: OCRTC		*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -159,18 +159,18 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 0 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
@@ -186,9 +186,9 @@
 
 #else /* Use EEPROM for environment variables */
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x300   /* 768 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x300	/* 768 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 #endif
 
@@ -200,12 +200,12 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
@@ -231,53 +231,53 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1) initialization                                  */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization					*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 2 (PLD - FPGA-boot) initialization                               */
-#define CFG_EBC_PB2AP           0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 2 (PLD - FPGA-boot) initialization				*/
+#define CFG_EBC_PB2AP		0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (PLD - OSL) initialization                                     */
-#define CFG_EBC_PB3AP           0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 3 (PLD - OSL) initialization					*/
+#define CFG_EBC_PB3AP		0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB3CR           0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit  */
+#define CFG_EBC_PB3CR		0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 4 (Spartan2 1) initialization                                    */
-#define CFG_EBC_PB4AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 4 (Spartan2 1) initialization					*/
+#define CFG_EBC_PB4AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB4CR           0xF209C000  /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB4CR		0xF209C000  /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
 
-/* Memory Bank 5 (Spartan2 2) initialization                                    */
-#define CFG_EBC_PB5AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 5 (Spartan2 2) initialization					*/
+#define CFG_EBC_PB5AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB5CR           0xF309C000  /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB5CR		0xF309C000  /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
 
-/* Memory Bank 6 (Virtex 1) initialization                                      */
-#define CFG_EBC_PB6AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 6 (Virtex 1) initialization					*/
+#define CFG_EBC_PB6AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB6CR           0xF409A000  /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB6CR		0xF409A000  /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
 
-/* Memory Bank 7 (Virtex 2) initialization                                      */
-#define CFG_EBC_PB7AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 7 (Virtex 2) initialization					*/
+#define CFG_EBC_PB7AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB7CR           0xF509A000  /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB7CR		0xF509A000  /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
 
 
-#define CFG_ETHERNET_MAC_ADDR   0x00000000      /* Pass Ethernet MAC to VxWorks */
+#define CFG_ETHERNET_MAC_ADDR	0x00000000	/* Pass Ethernet MAC to VxWorks */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CFG_TEMP_STACK_OCM	  1
 
 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
@@ -287,7 +287,7 @@
 #define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 
 /*

include/configs/ORSG.h

@@ -34,12 +34,12 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_ORSG   		1	/* ...on a ORSG board	        */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_ORSG		1	/* ...on a ORSG board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -51,7 +51,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_PCI	| \
@@ -59,7 +59,7 @@
 				CFG_CMD_ASKENV	| \
 				CFG_CMD_ELF	| \
 				CFG_CMD_BSP	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -67,9 +67,9 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -77,32 +77,32 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -110,26 +110,26 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_ADAPTER /* select pci adapter          */
-#undef  CONFIG_PCI_PNP			/* no pci plug-and-play         */
-					/* resource configuration       */
-
-#undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0411  /* PCI Device ID: ORSG          */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci adapter		*/
+#undef	CONFIG_PCI_PNP			/* no pci plug-and-play		*/
+					/* resource configuration	*/
+
+#undef	CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0411	/* PCI Device ID: ORSG		*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -157,18 +157,18 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
 #if 0 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
@@ -184,9 +184,9 @@
 
 #else /* Use EEPROM for environment variables */
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x300   /* 768 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x300	/* 768 bytes may be used for env vars */
 				   /* total size of a CAT24WC08 is 1024 bytes */
 #endif
 
@@ -198,12 +198,12 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+					/* last 4 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
@@ -229,53 +229,53 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1) initialization                                  */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization					*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 2 (PLD - FPGA-boot) initialization                               */
-#define CFG_EBC_PB2AP           0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 2 (PLD - FPGA-boot) initialization				*/
+#define CFG_EBC_PB2AP		0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (PLD - OSL) initialization                                     */
-#define CFG_EBC_PB3AP           0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 3 (PLD - OSL) initialization					*/
+#define CFG_EBC_PB3AP		0x02015480  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x0,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB3CR           0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit  */
+#define CFG_EBC_PB3CR		0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 4 (Spartan2 1) initialization                                    */
-#define CFG_EBC_PB4AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 4 (Spartan2 1) initialization					*/
+#define CFG_EBC_PB4AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB4CR           0xF209C000  /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB4CR		0xF209C000  /* BAS=0xF20,BS=16MB,BU=R/W,BW=32bit*/
 
-/* Memory Bank 5 (Spartan2 2) initialization                                    */
-#define CFG_EBC_PB5AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 5 (Spartan2 2) initialization					*/
+#define CFG_EBC_PB5AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB5CR           0xF309C000  /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
+#define CFG_EBC_PB5CR		0xF309C000  /* BAS=0xF30,BS=16MB,BU=R/W,BW=32bit*/
 
-/* Memory Bank 6 (Virtex 1) initialization                                      */
-#define CFG_EBC_PB6AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 6 (Virtex 1) initialization					*/
+#define CFG_EBC_PB6AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB6CR           0xF409A000  /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB6CR		0xF409A000  /* BAS=0xF40,BS=16MB,BU=R/W,BW=16bit*/
 
-/* Memory Bank 7 (Virtex 2) initialization                                      */
-#define CFG_EBC_PB7AP           0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
+/* Memory Bank 7 (Virtex 2) initialization					*/
+#define CFG_EBC_PB7AP		0x02015580  /* BME=0x0,TWT=0x04,CSN=0x0,OEN=0x1 */
 					    /* WBN=0x1,WBF=0x1,TH=0x2,RE=0x1,SOR=0x1,BEM=0x0,PEN=0x0*/
-#define CFG_EBC_PB7CR           0xF509A000  /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB7CR		0xF509A000  /* BAS=0xF50,BS=16MB,BU=R/W,BW=16bit*/
 
 
-#define CFG_ETHERNET_MAC_ADDR   0x00000000      /* Pass Ethernet MAC to VxWorks */
+#define CFG_ETHERNET_MAC_ADDR	0x00000000	/* Pass Ethernet MAC to VxWorks */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CFG_TEMP_STACK_OCM	  1
 
 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
@@ -285,7 +285,7 @@
 #define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 
 /*

include/configs/OXC.h

@@ -39,7 +39,7 @@
 #define CONFIG_MPC8240		1
 #define CONFIG_OXC		1
 
-#define CONFIG_BOARD_PRE_INIT	1	/* Call board_pre_init	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 #define CONFIG_IDENT_STRING     " [oxc] "
 

include/configs/P3G4.h

@@ -51,7 +51,7 @@
 
 /* which initialization functions to call for this board */
 #define CONFIG_MISC_INIT_R	1
-#define CONFIG_BOARD_PRE_INIT	1
+#define CONFIG_BOARD_EARLY_INIT_F 1
 
 #define CFG_BOARD_NAME		"P3G4"