add new board pm9g45

Add the new board PM9G45 from Ronetix GmbH.
* AT91SAM9G45 MCU at 400Mhz.
* 128MB DDR2 SDRAM
* 256MB NAND
* 10/100 MBits Ethernet DP83848
* Serial number chip DS2401

The board is made as SODIMM200 module.
For more info www.ronatix.at or info@ronetix.at.

Signed-off-by: Asen Dimov <dimov@ronetix.at>

MAINTAINERS

@@ -228,6 +228,7 @@ Ilko Iliev <iliev@ronetix.at>
 
 	PM9261		AT91SAM9261
 	PM9263		AT91SAM9263
+	PM9G45		ARM926EJS (AT91SAM9G45 SoC)
 
 Gary Jennejohn <garyj@denx.de>
 

MAKEALL

@@ -682,6 +682,7 @@ LIST_at91="			\
 	otc570			\
 	pm9261			\
 	pm9263			\
+	pm9g45			\
 	SBC35_A9G20		\
 	TNY_A9260		\
 	TNY_A9G20		\

Makefile

@@ -2873,6 +2873,10 @@ otc570_config	:	unconfig
 pm9263_config	:	unconfig
 	@$(MKCONFIG) $(@:_config=) arm arm926ejs pm9263 ronetix at91
 
+pm9g45_config	:	unconfig
+	@mkdir -p $(obj)include
+	@$(MKCONFIG) -a pm9g45 arm arm926ejs pm9g45 ronetix at91
+
 SBC35_A9G20_NANDFLASH_config \
 SBC35_A9G20_EEPROM_config \
 SBC35_A9G20_config	:	unconfig

board/ronetix/pm9g45/Makefile

@@ -0,0 +1,54 @@
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian.pop@leadtechdesign.com>
+# Lead Tech Design <www.leadtechdesign.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y += pm9g45.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/ronetix/pm9g45/config.mk

@@ -0,0 +1 @@
+TEXT_BASE = 0x73f00000

board/ronetix/pm9g45/pm9g45.c

@@ -0,0 +1,188 @@
+/*
+ * (C) Copyright 2010
+ * Ilko Iliev <iliev@ronetix.at>
+ * Asen Dimov <dimov@ronetix.at>
+ * Ronetix GmbH <www.ronetix.at>
+ *
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/sizes.h>
+#include <asm/arch/at91sam9g45.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/at91_matrix.h>
+#include <asm/arch/at91_pio.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
+#include <net.h>
+#endif
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+#ifdef CONFIG_CMD_NAND
+static void pm9g45_nand_hw_init(void)
+{
+	unsigned long csa;
+	at91_smc_t	*smc	= (at91_smc_t *) AT91_SMC_BASE;
+	at91_matrix_t	*matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+
+	/* Enable CS3 */
+	csa = readl(&matrix->ccr[6]) | AT91_MATRIX_CSA_EBI_CS3A;
+	writel(csa, &matrix->ccr[6]);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+
+	writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
+		AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2),
+		&smc->cs[3].pulse);
+
+	writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4),
+		&smc->cs[3].cycle);
+
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE |
+		AT91_SMC_MODE_DBW_8 |
+		AT91_SMC_MODE_TDF_CYCLE(3),
+		&smc->cs[3].mode);
+
+	writel(1 << AT91SAM9G45_ID_PIOC, &pmc->pcer);
+
+#ifdef CONFIG_SYS_NAND_READY_PIN
+	/* Configure RDY/BSY */
+	at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+#endif
+
+	/* Enable NandFlash */
+	at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+#endif
+
+#ifdef CONFIG_MACB
+static void pm9g45_macb_hw_init(void)
+{
+	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pio_t	*pio	= (at91_pio_t *) AT91_PIO_BASE;
+
+	/*
+	 * PD2 enables the 50MHz oscillator for Ethernet PHY
+	 * 1 - enable
+	 * 0 - disable
+	 */
+	at91_set_pio_output(AT91_PIO_PORTD, 2, 1);
+	at91_set_pio_value(AT91_PIO_PORTD, 2, 1); /* 1- enable, 0 - disable */
+
+	/* Enable clock */
+	writel(1 << AT91SAM9G45_ID_EMAC, &pmc->pcer);
+
+	/*
+	 * Disable pull-up on:
+	 *	RXDV (PA15) => PHY normal mode (not Test mode)
+	 *	ERX0 (PA12) => PHY ADDR0
+	 *	ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
+	 *
+	 * PHY has internal pull-down
+	 */
+	at91_set_pio_pullup(AT91_PIO_PORTA, 15, 0);
+	at91_set_pio_pullup(AT91_PIO_PORTA, 12, 0);
+	at91_set_pio_pullup(AT91_PIO_PORTA, 13, 0);
+
+	/* Re-enable pull-up */
+	at91_set_pio_pullup(AT91_PIO_PORTA, 15, 1);
+	at91_set_pio_pullup(AT91_PIO_PORTA, 12, 1);
+	at91_set_pio_pullup(AT91_PIO_PORTA, 13, 1);
+
+	at91_macb_hw_init();
+}
+#endif
+
+int board_init(void)
+{
+	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+
+	/* Enable Ctrlc */
+	console_init_f();
+
+	writel((1 << AT91SAM9G45_ID_PIOA) |
+		(1 << AT91SAM9G45_ID_PIOB) |
+		(1 << AT91SAM9G45_ID_PIOC) |
+		(1 << AT91SAM9G45_ID_PIODE), &pmc->pcer);
+
+	/* arch number of AT91SAM9M10G45EK-Board */
+	gd->bd->bi_arch_number = MACH_TYPE_PM9G45;
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	at91_serial_hw_init();
+#ifdef CONFIG_CMD_NAND
+	pm9g45_nand_hw_init();
+#endif
+
+#ifdef CONFIG_MACB
+	pm9g45_macb_hw_init();
+#endif
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void reset_phy(void)
+{
+#ifdef CONFIG_MACB
+	/*
+	 * Initialize ethernet HW addr prior to starting Linux,
+	 * needed for nfsroot
+	 */
+	eth_init(gd->bd);
+#endif
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_MACB
+	rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x01);
+#endif
+	return rc;
+}

include/configs/pm9g45.h

@@ -0,0 +1,186 @@
+/*
+ * (C) Copyright 2010
+ * Ilko Iliev <iliev@ronetix.at>
+ * Asen Dimov <dimov@ronetix.at>
+ * Ronetix GmbH <www.ronetix.at>
+ *
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * Configuation settings for the PM9G45 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_ARM926EJS	1	/* This is an ARM926EJS Core */
+#define CONFIG_PM9G45		1	/* It's an Ronetix PM9G45 */
+#define CONFIG_AT91SAM9G45	1	/* It's an Atmel AT91SAM9G45 SoC */
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000 /* from 12 MHz crystal */
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_ARCH_CPU_INIT
+
+#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG	1
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_AT91_GPIO	1
+#define CONFIG_ATMEL_USART	1
+#define CONFIG_USART3		1	/* USART 3 is DBGU */
+
+#define CONFIG_SYS_USE_NANDFLASH	1
+
+/* LED */
+#define CONFIG_AT91_LED
+#define	CONFIG_RED_LED		AT91_PIO_PORTD, 31 /* this is the user1 led */
+#define	CONFIG_GREEN_LED	AT91_PIO_PORTD, 0 /* this is the user2 led */
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE	1
+#define CONFIG_BOOTP_BOOTPATH		1
+#define CONFIG_BOOTP_GATEWAY		1
+#define CONFIG_BOOTP_HOSTNAME		1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_PING		1
+#define CONFIG_CMD_DHCP		1
+#define CONFIG_CMD_NAND		1
+#define CONFIG_CMD_USB		1
+
+#define CONFIG_CMD_JFFS2		1
+#define CONFIG_JFFS2_CMDLINE		1
+#define CONFIG_JFFS2_NAND		1
+#define CONFIG_JFFS2_DEV		"nand0" /* NAND dev jffs2 lives on */
+#define CONFIG_JFFS2_PART_OFFSET	0	/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE		(256 * 1024 * 1024) /* partition */
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			0x70000000
+#define PHYS_SDRAM_SIZE			0x08000000	/* 128 megs */
+
+/* NOR flash, not available */
+#define CONFIG_SYS_NO_FLASH		1
+#undef CONFIG_CMD_FLASH
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_MAX_CHIPS		1
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_DBW_8		1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN	AT91_PIO_PORTC, 14
+#define CONFIG_SYS_NAND_READY_PIN	AT91_PIO_PORTD, 3
+
+#endif
+
+/* Ethernet */
+#define CONFIG_MACB			1
+#define CONFIG_RMII			1
+#define CONFIG_NET_MULTI		1
+#define CONFIG_NET_RETRY_COUNT		20
+#define CONFIG_RESET_PHY_R		1
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW		1
+#define CONFIG_DOS_PARTITION		1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT	1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE	0x00700000 /* _UHP_OHCI_BASE */
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"at91sam9g45"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
+#define CONFIG_USB_STORAGE		1
+
+/* board specific(not enough SRAM) */
+#define CONFIG_AT91SAM9G45_LCD_BASE	PHYS_SDRAM + 0xE00000
+
+#define CONFIG_SYS_LOAD_ADDR		PHYS_SDRAM + 0x2000000 /* load addr */
+
+#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END		CONFIG_AT91SAM9G45_LCD_BASE
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_OFFSET		0x60000
+#define CONFIG_ENV_OFFSET_REDUND	0x80000
+#define CONFIG_ENV_SIZE			0x20000		/* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND	"nand read 0x72000000 0x200000 0x200000; bootm"
+#define CONFIG_BOOTARGS		"fbcon=rotate:3 console=tty0 " \
+				"console=ttyS0,115200 " \
+				"root=/dev/mtdblock4 " \
+				"mtdparts=atmel_nand:128k(bootstrap)ro," \
+				"256k(uboot)ro,1664k(env)," \
+				"2M(linux)ro,-(root) rw " \
+				"rootfstype=jffs2"
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{115200 , 19200, 38400, 57600, 9600 }
+
+#define CONFIG_SYS_PROMPT		"U-Boot> "
+#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP		1
+#define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\
+					0x1000)
+#define CONFIG_SYS_GBL_DATA_SIZE	128 /* 128 bytes for initial data */
+
+#define CONFIG_STACKSIZE		(32*1024)	/* regular stack */
+
+#ifdef CONFIG_USE_IRQ
+#error CONFIG_USE_IRQ not supported
+#endif
+
+#endif