* Patch by Yuli Barcohen, 3 Dec 2003:

  "revive" U-Boot support for old Motorola MPC860ADS board

* Patch by Cam(ilo?), 03 Dec 2003:
  make examples build even with broken Montavista objcopy

* Patch by Pavel Bartusek, 27 Nov 2003:
  fix conversion problem with "bootretry" evironment variable

CHANGELOG

@@ -2,6 +2,15 @@
 Changes since U-Boot 1.0.0:
 ======================================================================
 
+* Patch by Yuli Barcohen, 3 Dec 2003:
+  "revive" U-Boot support for old Motorola MPC860ADS board
+
+* Patch by Cam(ilo?), 03 Dec 2003:
+  make examples build even with broken Montavista objcopy
+
+* Patch by Pavel Bartusek, 27 Nov 2003:
+  fix conversion problem with "bootretry" evironment variable
+
 * Patch by Andre Schwarz, 24 Nov 2003:
   add support for mvblue (mvBlueLYNX and mvBlueBOX) boards
 

Makefile

@@ -115,6 +115,7 @@ SUBDIRS	= tools \
 	  examples \
 	  post \
 	  post/cpu
+.PHONY : $(SUBDIRS)
 
 #########################################################################
 #########################################################################
@@ -150,7 +151,7 @@ $(LIBS):
 
 $(SUBDIRS):
 		@echo "#### MAKE $@ ####"
-		$(MAKE) -C $@
+		$(MAKE) -C $@ all
 
 gdbtools:
 		$(MAKE) -C tools/gdb || exit 1

board/fads/config.mk

@@ -22,9 +22,9 @@
 #
 
 #
-# FADS boards
+# Motorola old MPC821/860ADS, MPC8xxFADS, and new MPC866ADS boards
 #
 
-#TEXT_BASE = 0xFE000000
-TEXT_BASE = 0x02800000
-OBJCFLAGS =	--set-section-flags=.ppcenv=contents,alloc,load,data
+TEXT_BASE = 0xFE000000
+#TEXT_BASE = 0x02800000
+#OBJCFLAGS = --set-section-flags=.ppcenv=contents,alloc,load,data

board/fads/fads.c

@@ -360,7 +360,11 @@ static int _draminit (uint base, uint noMbytes, uint edo, uint delay)
 
 	switch (noMbytes) {
 	case 4:				/* 4 Mbyte uses only CS2 */
+#ifdef CONFIG_ADS
+		memctl->memc_mamr = 0xc0a21114;
+#else
 		memctl->memc_mamr = 0x13a01114;	/* PTA 0x13 AMA 010 */
+#endif
 		memctl->memc_or2 = 0xffc00800;	/* 4M */
 		break;
 
@@ -393,17 +397,18 @@ static int _draminit (uint base, uint noMbytes, uint edo, uint delay)
 
 	memctl->memc_br2 = 0x81 + base;	/* use upma */
 
+	*((uint *) BCSR1) &= ~BCSR1_DRAM_EN;	/* enable dram */
+
 	/* if no dimm is inserted, noMbytes is still detected as 8m, so
 	 * sanity check top and bottom of memory */
 
-	*((uint *) BCSR1) &= ~BCSR1_DRAM_EN;	/* enable dram */
-
 	/* check bytes / 2 because dram_size tests at base+bytes, which
 	 * is not mapped */
-	if (dram_size ((long *) base, noMbytes << 19) != noMbytes << 19) {
-		*((uint *) BCSR1) |= BCSR1_DRAM_EN;	/* disable dram */
-		return -1;
-	}
+	if (noMbytes == 8)
+		if (dram_size ((long *) base, noMbytes << 19) != noMbytes << 19) {
+			*((uint *) BCSR1) |= BCSR1_DRAM_EN;	/* disable dram */
+			return -1;
+		}
 
 	return 0;
 }

board/fads/lamp.c

@@ -1,4 +1,7 @@
 #include <config.h>
+
+#ifndef CONFIG_ADS /* Old ADS has not got any user-controllable LED */
+
 #include <common.h>
 
 void
@@ -40,3 +43,5 @@ fast_blink(unsigned int n)
     signal_delay(0x00100000);
   }
 }
+
+#endif /* !CONFIG_ADS */

board/fads/u-boot.lds

@@ -22,9 +22,6 @@
  */
 
 OUTPUT_ARCH(powerpc)
-SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
-/* Do we need any of these for elf?
-   __DYNAMIC = 0;    */
 SECTIONS
 {
   /* Read-only sections, merged into text segment: */
@@ -33,41 +30,30 @@ SECTIONS
   .hash          : { *(.hash)		}
   .dynsym        : { *(.dynsym)		}
   .dynstr        : { *(.dynstr)		}
-  .rel.text      : { *(.rel.text)		}
+  .rel.text      : { *(.rel.text)	}
   .rela.text     : { *(.rela.text) 	}
-  .rel.data      : { *(.rel.data)		}
+  .rel.data      : { *(.rel.data)	}
   .rela.data     : { *(.rela.data) 	}
   .rel.rodata    : { *(.rel.rodata) 	}
   .rela.rodata   : { *(.rela.rodata) 	}
-  .rel.got       : { *(.rel.got)		}
-  .rela.got      : { *(.rela.got)		}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
   .rel.ctors     : { *(.rel.ctors)	}
   .rela.ctors    : { *(.rela.ctors)	}
   .rel.dtors     : { *(.rel.dtors)	}
   .rela.dtors    : { *(.rela.dtors)	}
-  .rel.bss       : { *(.rel.bss)		}
-  .rela.bss      : { *(.rela.bss)		}
-  .rel.plt       : { *(.rel.plt)		}
-  .rela.plt      : { *(.rela.plt)		}
-  .init          : { *(.init)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
   .plt : { *(.plt) }
   .text      :
   {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+    cpu/mpc8xx/start.o		(.text)
 
-    cpu/mpc8xx/start.o	(.text)
-/*
-    cpu/mpc8xx/start.o	(.text)
-    common/dlmalloc.o	(.text)
-    lib_ppc/ppcstring.o	(.text)
-    lib_generic/vsprintf.o	(.text)
-    lib_generic/crc32.o		(.text)
-    lib_generic/zlib.o		(.text)
-
-    . = env_offset;
-    common/environment.o(.text)
-*/
+    . = DEFINED(env_offset) ? env_offset : .;
+    common/environment.o	(.ppcenv)
 
     *(.text)
     *(.fixup)
@@ -136,11 +122,7 @@ SECTIONS
    *(.bss)
    *(COMMON)
   }
-  . = ALIGN(256 * 1024);
-  .ppcenv	:
-  {
-    common/environment.o (.ppcenv)
-  }
   _end = . ;
   PROVIDE (end = .);
 }
+ENTRY(_start)

common/cmd_pcmcia.c

@@ -57,7 +57,7 @@
 #include <command.h>
 #include <config.h>
 #include <pcmcia.h>
-#if defined(CONFIG_IDE_8xx_PCCARD) && defined(CONFIG_8xx)
+#if defined(CONFIG_8xx)
 #include <mpc8xx.h>
 #endif
 #if defined(CONFIG_LWMON)

common/main.c

@@ -505,7 +505,7 @@ void init_cmd_timeout(void)
 	char *s = getenv ("bootretry");
 
 	if (s != NULL)
-		retry_time = (int)simple_strtoul(s, NULL, 10);
+		retry_time = (int)simple_strtol(s, NULL, 10);
 	else
 		retry_time =  CONFIG_BOOT_RETRY_TIME;
 

cpu/mpc8xx/cpu_init.c

@@ -145,9 +145,7 @@ void cpu_init_f (volatile immap_t * immr)
     defined(CONFIG_R360MPI)	|| \
     defined(CONFIG_RPXCLASSIC)	|| \
     defined(CONFIG_RPXLITE)	|| \
-    defined(CONFIG_SPD823TS)	|| \
-    defined(CONFIG_MPC86xADS)	|| \
-   (defined(CONFIG_MPC860T) && defined(CONFIG_FADS))
+    defined(CONFIG_SPD823TS)
 
 	memctl->memc_br0 = CFG_BR0_PRELIM;
 #endif

cpu/mpc8xx/serial.c

@@ -153,7 +153,7 @@ int serial_init (void)
 # endif
 #endif
 
-#if defined(CONFIG_FADS)
+#if defined(CONFIG_FADS) || defined(CONFIG_ADS)
 	/* Enable RS232 */
 #if defined(CONFIG_8xx_CONS_SMC1)
 	*((uint *) BCSR1) &= ~BCSR1_RS232EN_1;

examples/Makefile

@@ -104,7 +104,7 @@ $(LIB): .depend $(LIBOBJS)
 	$(OBJCOPY) -O srec $(<:.o=) $@
 
 %.bin:	%.srec
-	$(OBJCOPY) -O binary $< $@ 2>/dev/null
+	$(OBJCOPY) -O binary $(<:.srec=) $@ 2>/dev/null
 
 #########################################################################
 

include/configs/ADS860.h

@@ -16,29 +16,31 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#include <mpc8xx_irq.h>
 
+/* Board type */
+#define CONFIG_ADS		1	/* Old Motorola MPC821/860ADS */
+
+/* Processor type */
 #define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_ADS		1
 
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1	    */
+#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1 */
 #undef	CONFIG_8xx_CONS_SMC2
 #undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		19200	/* console baudrate */
-#define CONFIG_PCMCIA		1	/* To enable PCMCIA support */
 
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address defaults */
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_BAUDRATE		38400	/* Console baudrate */
 
+/* CFG_8XX_FACT * CFG_8XX_XIN = 50 MHz */
+#if 0
 #define CFG_8XX_XIN		32768	/* 32.768 kHz input frequency	*/
 #define CFG_8XX_FACT		0x5F6	/* Multiply by 1526 */
-					/* MPC8XX_FACT * MPC8XX_XIN = 50 MHz */
+#else
+#define CFG_8XX_XIN		4000000	/* 4 MHz input frequency	*/
+#define CFG_8XX_FACT		12	/* Multiply by 12 */
+#endif
 
 #define CONFIG_8xx_GCLK_FREQ   ((CFG_8XX_XIN) * (CFG_8XX_FACT))
 
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define CONFIG_DRAM_50MHZ	1
 
 #if 0
 #define CONFIG_BOOTDELAY	-1	/* autoboot disabled	    */
@@ -47,11 +49,11 @@
 #endif
 
 #undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND			    \
-    "bootp; "				    \
-    "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	    \
-    "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; "   \
-    "bootm"
+#define CONFIG_BOOTCOMMAND						\
+   "dhcp;"								\
+   "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+   "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+   "bootm"
 
 #define CONFIG_LOADS_ECHO	1   /* echo on for serial download  */
 #undef	CFG_LOADS_BAUD_CHANGE	    /* don't allow baudrate change  */
@@ -60,18 +62,16 @@
 
 #define CONFIG_BOOTP_MASK   (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
 
-
-#if 0					/* private command defs */
-#define CONFIG_COMMANDS	    (CONFIG_CMD_DFL | CFG_CMD_I2C | \
-			     CFG_CMD_IDE | CFG_CMD_PCMCIA)
-#endif
-					/* default command defs */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_CACHE)
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL  \
+			 | CFG_CMD_DHCP  \
+			 | CFG_CMD_IMMAP \
+			 | CFG_CMD_PCMCIA \
+			 | CFG_CMD_PING  \
+			)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-
 /*
  * Miscellaneous configurable options
  */
@@ -103,7 +103,7 @@
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
-#define CFG_IMMR		0xfff00000
+#define CFG_IMMR		0xFF000000
 #define CFG_IMMR_SIZE		((uint)(64 * 1024))
 
 /*-----------------------------------------------------------------------
@@ -121,13 +121,6 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE	    0x00000000
-#define CFG_SRAM_BASE	    0x00000000
-#define CFG_FLASH_BASE	    0xfe000000
-#define CFG_FLASH_SIZE	    ((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-
-#define CFG_MONITOR_LEN	    (384 << 10) /* Reserve 384 kB for Monitor	*/
-#define CFG_MONITOR_BASE    CFG_FLASH_BASE
-#define CFG_MALLOC_LEN	    (384 << 10) /* Reserve 384 kB for malloc()	*/
 
 /*
  * For booting Linux, the board info and command line data
@@ -138,6 +131,9 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
+#define CFG_FLASH_BASE	    TEXT_BASE
+#define CFG_FLASH_SIZE	    ((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
+
 #define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks	    */
 #define CFG_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
 
@@ -148,9 +144,14 @@
 #undef	CFG_ENV_IS_IN_EEPROM
 #define CFG_ENV_IS_IN_FLASH	1
 
-#define CFG_ENV_OFFSET		0x00040000
-#define CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector */
 #define CFG_ENV_SECT_SIZE	0x40000 /* see README - env sector total size	*/
+#define CFG_ENV_OFFSET		CFG_ENV_SECT_SIZE
+#define CFG_ENV_SIZE		0x4000	/* Total Size of Environment */
+
+#define CFG_MONITOR_BASE    CFG_FLASH_BASE
+#define CFG_MONITOR_LEN	    (256 << 10) /* Reserve one flash sector
+					   (256 KB) for monitor */
+#define CFG_MALLOC_LEN	    (384 << 10) /* Reserve 384 kB for malloc()	*/
 
 /* the other CS:s are determined by looking at parameters in BCSRx */
 
@@ -162,6 +163,15 @@
 #define CFG_CACHELINE_SHIFT 4		/* log base 2 of the above value    */
 #endif
 
+/*-----------------------------------------------------------------------
+ * I2C configuration
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_I2C)
+#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address defaults */
+#define CFG_I2C_SLAVE		0x7F
+#endif
+
 /*-----------------------------------------------------------------------
  * SYPCR - System Protection Control			11-9
  * SYPCR can only be written once after reset!
@@ -176,7 +186,7 @@
 #endif
 
 /*-----------------------------------------------------------------------
- * SUMCR - SIU Module Configuration		    11-6
+ * SUMCR - SIU Module Configuration			11-6
  *-----------------------------------------------------------------------
  * PCMCIA config., multi-function pin tri-state
  */
@@ -234,40 +244,22 @@
 /*
  * Init Memory Controller:
  *
- * BR0/1 and OR0/1 (FLASH)
+ * BR0 and OR0 (FLASH)
+ * BR1 and OR1 (BCSR)
  */
 /* the other CS:s are determined by looking at parameters in BCSRx */
 
 #define BCSR_ADDR	   ((uint) 0xff010000)
-#define BCSR_SIZE	   ((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM  0xfe000000	/* FLASH bank #0    */
-#define FLASH_BASE1_PRELIM  0x00000000	/* FLASH bank #1    */
 
-#define CFG_REMAP_OR_AM	    0xff000000	/* OR addr mask */
-#define CFG_PRELIM_OR_AM    0xffe00000	/* OR addr mask */
+#define CFG_PRELIM_OR_AM    0xff800000	/* OR addr mask */
 
 /* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0    */
 #define CFG_OR_TIMING_FLASH (OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
 
-#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
-
-#ifdef USE_REAL_FLASH_VALUES
-/*
- * These values fit our FADS860T ...
- * The "default" behaviour with 1Mbyte initial doesn't work for us!
- */
-#define CFG_BR0_PRELIM	0x0fe000001	/* Real values for the board */
-#define CFG_OR0_PRELIM	0x0ffe00d34
-#define CFG_BR2_PRELIM	0x000000081
-#define CFG_OR2_PRELIM	0x0ff000800
-#else
-#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-#endif
+#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)   /* 8 Mbyte until detected */
+#define CFG_BR0_PRELIM	(CFG_FLASH_BASE | BR_V)
 
 /* BCSRx - Board Control and Status Registers */
-/* #define CFG_OR1_REMAP    CFG_OR0_REMAP */
 #define CFG_OR1_PRELIM	0xffff8110	/* 64Kbyte address space */
 #define CFG_BR1_PRELIM	((BCSR_ADDR) | BR_V )
 
@@ -275,9 +267,6 @@
  * Memory Periodic Timer Prescaler
  */
 
-/* periodic timer for refresh */
-#define CFG_MAMR_PTA	    97	/* start with divider for 100 MHz   */
-
 /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
 #define CFG_MPTPR_2BK_4K    MPTPR_PTP_DIV16	/* setting for 2 banks	*/
 #define CFG_MPTPR_1BK_4K    MPTPR_PTP_DIV32	/* setting for 1 bank	*/
@@ -286,20 +275,6 @@
 #define CFG_MPTPR_2BK_8K    MPTPR_PTP_DIV8	/* setting for 2 banks	*/
 #define CFG_MPTPR_1BK_8K    MPTPR_PTP_DIV16	/* setting for 1 bank	*/
 
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CFG_MAMR_8COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-	     MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |   \
-	     MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-	     MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
-	     MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
-
-#define CFG_MAMR	0x13a01114
 /*
  * Internal Definitions
  *
@@ -310,11 +285,10 @@
 
 
 /* values according to the manual */
-#define BCSR0	((uint) (BCSR_ADDR + 00))
-#define BCSR1	((uint) (BCSR_ADDR + 0x04))
-#define BCSR2	((uint) (BCSR_ADDR + 0x08))
-#define BCSR3	((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4	((uint) (BCSR_ADDR + 0x10))
+#define BCSR0	(BCSR_ADDR + 0x00)
+#define BCSR1	(BCSR_ADDR + 0x04)
+#define BCSR2	(BCSR_ADDR + 0x08)
+#define BCSR3	(BCSR_ADDR + 0x0c)
 
 
 /*-----------------------------------------------------------------------
@@ -322,6 +296,10 @@
  *-----------------------------------------------------------------------
  *
  */
+#ifdef CONFIG_MPC860
+#define PCMCIA_SLOT_A 1
+#endif
+
 #define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
 #define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
 #define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
@@ -331,7 +309,6 @@
 #define CFG_PCMCIA_IO_ADDR	(0xEC000000)
 #define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
 
-
 /*-----------------------------------------------------------------------
  * IDE/ATA stuff
  *-----------------------------------------------------------------------
@@ -346,7 +323,6 @@
 #define CFG_PIO_MODE		0   /* IDE interface in PIO Mode 0  */
 #define CFG_PC_IDE_RESET	((ushort)0x0008)    /* PC 12	*/
 
-/* #define CFG_ATA_BASE_ADDR	0xFE100000 */
 #define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
 #define CFG_ATA_IDE0_OFFSET	0x0000
 
@@ -354,6 +330,8 @@
 #define CFG_ATA_REG_OFFSET	0x0080	/* Offset for normal register accesses	*/
 #define CFG_ATA_ALT_OFFSET	0x0100	/* Offset for alternate registers   */
 
+#define CONFIG_DISK_SPINUP_TIME 1000000
+#undef CONFIG_DISK_SPINUP_TIME	/* usin´ Compact Flash */
 
 /* (F)ADS bitvalues by Helmut Buchsbaum
  * see MPC8xxADS User's Manual for a proper description
@@ -399,65 +377,6 @@
 #define BCSR3_BREVN1		 ((ushort)0x0008)
 #define BCSR3_BREVN2_MASK	 ((ushort)0x0003)
 
-#define BCSR4_ETHLOOP		 ((uint)0x80000000)
-#define BCSR4_TFPLDL		 ((uint)0x40000000)
-#define BCSR4_TPSQEL		 ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP	 ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN		 ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN		 ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN		 ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED		 ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0		 ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO		 ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE		 ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON		 ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN	 ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1		 ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST		 ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST		 ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_MODEM_EN		 ((uint)0x00100000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_DATA_VOICE	 ((uint)0x00080000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC850
-#define BCSR4_DATA_VOICE	 ((uint)0x00080000)
-#endif /* CONFIG_MPC850 */
-
-#define CONFIG_DRAM_50MHZ	1
-#define CONFIG_SDRAM_50MHZ
-
-#ifdef CONFIG_MPC860T
-/* Interrupt level assignments.
- */
-#define FEC_INTERRUPT	SIU_LEVEL1  /* FEC interrupt */
-#endif /* CONFIG_MPC860T */
-
 /* We don't use the 8259.
  */
 #define NR_8259_INTS	0
@@ -466,17 +385,4 @@
  */
 #define _MACH_8xx (_MACH_ads)
 
-#if 0
-#define CONFIG_DISK_SPINUP_TIME 1000000
-#endif
-#undef CONFIG_DISK_SPINUP_TIME	/* usin´ Compact Flash */
-
-
-/* PCMCIA configuration
- */
-#define PCMCIA_MAX_SLOTS    2
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
 #endif	/* _CONFIG_ADS860_H */

include/configs/FADS860T.h

@@ -30,7 +30,6 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#include <mpc8xx_irq.h>
 
 /* board type */
 #define CONFIG_FADS		1       /* old/new FADS + new ADS */
@@ -58,9 +57,6 @@
 /* in general, we always know this for FADS+new ADS anyway */
 #define CONFIG_8xx_GCLK_FREQ     MPC8XX_HZ
 
-/* most vanilla kernels do not like this, set to 0 if in doubt */
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
 #if 1
 #define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
 #else
@@ -163,11 +159,11 @@
 # define	CFG_SDRAM_SIZE	0x00000000      /* NO SDRAM */
 #endif
 
-#define CFG_FLASH_BASE		0x02800000
+#define CFG_FLASH_BASE		TEXT_BASE
 
 #define CFG_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
 
-#define	CFG_MONITOR_LEN		(272 << 10)	/* Reserve 272 kB for Monitor	*/
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CFG_MONITOR_BASE	CFG_FLASH_BASE
 #define	CFG_MALLOC_LEN		(384 << 10)	/* Reserve 384 kB for malloc()	*/
 
@@ -184,7 +180,7 @@
 #define CFG_MAX_FLASH_SECT	16      /* max number of sectors on one chip	*/
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500		/* Timeout for Flash Write (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
 #define	CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_OFFSET		0x00040000
@@ -276,14 +272,11 @@
 #define BCSR_ADDR		((uint) 0xFF010000)
 #define BCSR_SIZE		((uint)(64 * 1024))
 
-#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
 #define CFG_PRELIM_OR_AM	0xFF800000	/* OR addr mask */
 
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
 #define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
 
-#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
-
 #ifdef USE_REAL_FLASH_VALUES
 /*
  * These values fit our FADS860T ...
@@ -297,7 +290,6 @@
 #endif
 
 /* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_REMAP	CFG_OR0_REMAP
 #define CFG_OR1_PRELIM	0xffff8110		/* 64Kbyte address space */
 #define CFG_BR1_PRELIM	((BCSR_ADDR) | BR_V )
 
@@ -316,7 +308,7 @@
 #define PCMCIA_MEM_ADDR		((uint)0xff020000)
 #define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
 
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
+#define	BCSR0			((uint) (BCSR_ADDR + 0x00))
 #define	BCSR1			((uint) (BCSR_ADDR + 0x04))
 #define	BCSR2			((uint) (BCSR_ADDR + 0x08))
 #define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
@@ -418,14 +410,6 @@
 #define CONFIG_DRAM_50MHZ		1
 #define CONFIG_SDRAM_50MHZ              1
 
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
 /* We don't use the 8259.
 */
 #define NR_8259_INTS	0
@@ -439,8 +423,6 @@
 
 /* PCMCIA configuration */
 
-#define PCMCIA_MAX_SLOTS    2
-
 #ifdef CONFIG_MPC860
 #define PCMCIA_SLOT_A 1
 #endif

include/configs/MPC86xADS.h

@@ -9,10 +9,10 @@
  * 1999-nov-26: The FADS is using the following physical memorymap:
  *
  * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR       connected to CS1, setup by 8xxrom
+ * ff010000 -> ff01ffff : BCSR       connected to CS1
  * ff000000 -> ff00ffff : IMAP       internal in the cpu
- * fe000000 -> ffnnnnnn : flash      connected to CS0, setup by 8xxrom
- * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
+ * fe000000 -> fennnnnn : flash      connected to CS0
+ * 00000000 -> nnnnnnnn : sdram      connected to CS4
  */
 
 /* ------------------------------------------------------------------------- */
@@ -28,7 +28,6 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#include <mpc8xx_irq.h>
 
 /* board type */
 #define CONFIG_MPC86xADS        1       /* new ADS */
@@ -66,9 +65,6 @@
 /* in general, we always know this for FADS+new ADS anyway */
 #define CONFIG_8xx_GCLK_FREQ     MPC8XX_HZ
 
-/* most vanilla kernels do not like this, set to 0 if in doubt */
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
 #if 1
 #define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
 #else
@@ -76,14 +72,12 @@
 #endif
 
 #undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND			    \
-    "bootp; "				    \
-    "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	    \
-    "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; "   \
+#define CONFIG_BOOTCOMMAND							\
+    "dhcp;"									\
+    "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "		\
+    "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
     "bootm"
 
-/* #include "local.h" */
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 /* ATA / IDE and partition support */
@@ -96,21 +90,27 @@
 #undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
 #undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
 
-/* choose SCC1 ethernet (10BASET on motherboard)
- * or FEC ethernet (10/100 on daughterboard)
+/*
+ * New MPC86xADS provides two Ethernet connectivity options:
+ * 10Mbit/s on SCC1 and 100Mbit/s on FEC. All new PQ1 chips
+ * has got FEC so FEC is the default.
  */
-#if 0
-#define	CONFIG_SCC1_ENET	1	/* use SCC1 ethernet */
-#undef	CONFIG_FEC_ENET			/* disable FEC ethernet  */
-#else   /* all 86x cores have FECs, if in doubt, use it */
 #undef	CONFIG_SCC1_ENET		/* disable SCC1 ethernet */
 #define	CONFIG_FEC_ENET		1	/* use FEC ethernet  */
+#ifdef CONFIG_FEC_ENET
 #define CFG_DISCOVER_PHY
 #endif
 #if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
 #error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
 #endif
 
+#define CONFIG_COMMANDS	(CONFIG_CMD_DFL  \
+			 | CFG_CMD_DHCP  \
+			 | CFG_CMD_IMMAP \
+			 | CFG_CMD_MII   \
+			 | CFG_CMD_PING  \
+			)
+
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
@@ -128,13 +128,6 @@
 #define	CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0100000	/* memtest works on	*/
-#if (CFG_SDRAM_SIZE)
-#define CFG_MEMTEST_END		CFG_SDRAM_SIZE	/* 1 ... SDRAM_SIZE	*/
-#else
-#define CFG_MEMTEST_END		0x0400000     	/* 1 ... 4 MB in DRAM	*/
-#endif
-
 #define CFG_LOAD_ADDR	 	0x00100000
 
 #define	CFG_HZ		        1000		/* decr freq: 1 ms ticks */
@@ -167,23 +160,20 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define	CFG_SDRAM_BASE		0x00000000
-#ifdef CONFIG_FADS
-# ifdef CONFIG_MPC86xADS /* new ADS */
-#  define	CFG_SDRAM_SIZE	0x00800000      /* 8 meg */
-# else                   /* old/new FADS */
-#  define	CFG_SDRAM_SIZE	0x00400000      /* 4 meg */
-# endif
-#else   /* !CONFIG_FADS */ /* old ADS */
-# define	CFG_SDRAM_SIZE	0x00000000      /* NO SDRAM */
+#if defined(CONFIG_MPC86xADS) /* new ADS */
+#define	CFG_SDRAM_SIZE	0x00800000      /* 8 meg */
+#elif defined(CONFIG_FADS)    /* old/new FADS */
+#define	CFG_SDRAM_SIZE	0x00400000      /* 4 meg */
+#else                         /* old ADS */
+#define	CFG_SDRAM_SIZE	0x00000000      /* No SDRAM */
 #endif
 
-#define CFG_FLASH_BASE		0x02800000
-
-#define CFG_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-
-#define	CFG_MONITOR_LEN		(272 << 10)	/* Reserve 272 kB for Monitor	*/
-#define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define	CFG_MALLOC_LEN		(384 << 10)	/* Reserve 384 kB for malloc()	*/
+#define CFG_MEMTEST_START	0x0100000	/* memtest works on	*/
+#if (CFG_SDRAM_SIZE)
+#define CFG_MEMTEST_END		CFG_SDRAM_SIZE	/* 1 ... SDRAM_SIZE	*/
+#else
+#define CFG_MEMTEST_END		0x0400000     	/* 1 ... 4 MB in DRAM	*/
+#endif /* CFG_SDRAM_SIZE */
 
 /*
  * For booting Linux, the board info and command line data
@@ -194,6 +184,9 @@
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
+#define CFG_FLASH_BASE		TEXT_BASE
+#define CFG_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
+
 #define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
 #define CFG_MAX_FLASH_SECT	16      /* max number of sectors on one chip	*/
 
@@ -201,10 +194,13 @@
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
 #define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x00040000
-#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
 #define CFG_ENV_SECT_SIZE	0x40000	/* see README - env sector total size	*/
+#define CFG_ENV_OFFSET		CFG_ENV_SECT_SIZE
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment		*/
+
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 KB for monitor	*/
+#define	CFG_MALLOC_LEN		(384 << 10)	/* Reserve 384 kB for malloc()	*/
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
@@ -215,7 +211,7 @@
 #endif
 
 /*-----------------------------------------------------------------------
- * SYPCR - System Protection Control					11-9
+ * SYPCR - System Protection Control				11-9
  * SYPCR can only be written once after reset!
  *-----------------------------------------------------------------------
  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
@@ -228,14 +224,14 @@
 #endif
 
 /*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration					11-6
+ * SIUMCR - SIU Module Configuration				11-6
  *-----------------------------------------------------------------------
  * PCMCIA config., multi-function pin tri-state
  */
 #define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 
 /*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control					11-26
+ * TBSCR - Time Base Status and Control				11-26
  *-----------------------------------------------------------------------
  * Clear Reference Interrupt Status, Timebase freezing enabled
  */
@@ -249,9 +245,9 @@
 #define CFG_PISCR	(PISCR_PS | PISCR_PITF)
 
 /*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
  *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
+ * set the PLL, the low-power modes and the reset control 	(15-29)
  */
 #define CFG_PLPRCR	((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) |	\
 				PLPRCR_SPLSS | PLPRCR_TEXPS)
@@ -283,34 +279,23 @@
 /*
  * Init Memory Controller:
  *
- * BR0/1 and OR0/1 (FLASH)
+ * BR0/OR0 (Flash)
+ * BR1/OR1 (BCSR)
  */
 /* the other CS:s are determined by looking at parameters in BCSRx */
 
 #define BCSR_ADDR		((uint) 0xFF010000)
 #define BCSR_SIZE		((uint)(64 * 1024))
 
-#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
 #define CFG_PRELIM_OR_AM	0xFF800000	/* OR addr mask */
 
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
 #define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
 
-#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
-
-#ifdef USE_REAL_FLASH_VALUES
-/*
- * The "default" behaviour with 1Mbyte initial doesn't work for us!
- */
-#define CFG_OR0_PRELIM	0x0FFC00D34 /* Real values for the board */
-#define CFG_BR0_PRELIM	0x02800001  /* Real values for the board */
-#else
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)   /* 8 Mbyte until detected */
 #define CFG_BR0_PRELIM	((CFG_FLASH_BASE & BR_BA_MSK) | BR_V )
-#endif
 
 /* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_REMAP	CFG_OR0_REMAP
 #define CFG_OR1_PRELIM	0xffff8110		/* 64Kbyte address space */
 #define CFG_BR1_PRELIM	((BCSR_ADDR) | BR_V )
 
@@ -327,7 +312,7 @@
 #define PCMCIA_MEM_ADDR		((uint)0xff020000)
 #define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
 
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
+#define	BCSR0			((uint) (BCSR_ADDR + 0x00))
 #define	BCSR1			((uint) (BCSR_ADDR + 0x04))
 #define	BCSR2			((uint) (BCSR_ADDR + 0x08))
 #define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
@@ -389,10 +374,6 @@
 #define CONFIG_DRAM_50MHZ		1
 #define CONFIG_SDRAM_50MHZ              1
 
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
-
 /* We don't use the 8259.
 */
 #define NR_8259_INTS	0
@@ -406,12 +387,10 @@
 
 /* PCMCIA configuration */
 
-#define PCMCIA_MAX_SLOTS    2
-
 #ifdef CONFIG_MPC860
 #define PCMCIA_SLOT_A 1
 #endif
-/*#define CFG_PCMCIA_MEM_SIZE     ( 64 << 20) */
+
 #define CFG_PCMCIA_MEM_ADDR	(0x50000000)
 #define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
 #define CFG_PCMCIA_DMA_ADDR	(0x54000000)