board/[q-z]*: Remove obsolete references to CONFIG_COMMANDS

Signed-off-by: Jon Loeliger <jdl@freescale.com>

board/r360mpi/pcmcia.c

@@ -4,11 +4,11 @@
 
 #undef	CONFIG_PCMCIA
 
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) || defined(CONFIG_CMD_PCMCIA)
+#if defined(CONFIG_CMD_PCMCIA)
 #define	CONFIG_PCMCIA
 #endif
 
-#if ((CONFIG_COMMANDS & CFG_CMD_IDE) || defined(CONFIG_CMD_IDE)) && defined(CONFIG_IDE_8xx_PCCARD)
+#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
 #define	CONFIG_PCMCIA
 #endif
 
@@ -123,7 +123,7 @@ int pcmcia_hardware_enable(int slot)
 }
 
 
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) || defined(CONFIG_CMD_PCMCIA)
+#if defined(CONFIG_CMD_PCMCIA)
 int pcmcia_hardware_disable(int slot)
 {
 	volatile immap_t	*immap;

board/sacsng/sacsng.c

@@ -837,7 +837,7 @@ void show_boot_progress (int status)
 /*
  * The following are used to control the SPI chip selects for the SPI command.
  */
-#if (CONFIG_COMMANDS & CFG_CMD_SPI) || defined(CONFIG_CMD_SPI)
+#if defined(CONFIG_CMD_SPI)
 
 #define SPI_ADC_CS_MASK	0x00000800
 #define SPI_DAC_CS_MASK	0x00001000

board/sbc2410x/sbc2410x.c

@@ -31,7 +31,7 @@
 #include <common.h>
 #include <s3c2410.h>
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 #include <linux/mtd/nand.h>
 #endif
 
@@ -136,7 +136,7 @@ int dram_init (void)
 	return 0;
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 extern ulong nand_probe(ulong physadr);
 
 static inline void NF_Reset(void)
@@ -180,4 +180,4 @@ void nand_init(void)
 #endif
 	printf ("%4lu MB\n", nand_probe((ulong)nand) >> 20);
 }
-#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */
+#endif

board/sc3/sc3nand.c

@@ -23,7 +23,7 @@
 
 #include <common.h>
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 
 #include <nand.h>
 #include <asm/processor.h>

board/siemens/common/fpga.c

@@ -219,7 +219,7 @@ static int fpga_load (fpga_t* fpga, ulong addr, int checkall)
     return 1;
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 
 /* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . */
 
@@ -299,7 +299,7 @@ U_BOOT_CMD(
 	"fpga load [name] addr - load FPGA configuration data\n"
 );
 
-#endif	/* CONFIG_COMMANDS & CFG_CMD_BSP */
+#endif
 
 /* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . */
 

board/siemens/pcu_e/pcu_e.c

@@ -368,7 +368,7 @@ void reset_phy (void)
 /*-----------------------------------------------------------------------
  * Board Special Commands: access functions for "PUMA" FPGA
  */
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 
 #define	PUMA_READ_MODE	0
 #define PUMA_LOAD_MODE	1

board/sixnet/sixnet.c

@@ -33,7 +33,7 @@
 # include <status_led.h>
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 #include <linux/mtd/nand_legacy.h>
 extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
 #endif
@@ -75,7 +75,7 @@ int checkboard (void)
 
 /* ------------------------------------------------------------------------- */
 
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) || defined(CONFIG_CMD_PCMCIA)
+#if defined(CONFIG_CMD_PCMCIA)
 #error "SXNI855T has no PCMCIA port"
 #endif	/* CFG_CMD_PCMCIA */
 
@@ -327,7 +327,7 @@ int misc_init_r (void)
 	return (0);
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 void nand_init(void)
 {
 	unsigned long totlen = nand_probe(CFG_DFLASH_BASE);

board/ssv/adnpesc1/adnpesc1.c

@@ -65,7 +65,7 @@ long int initdram (int board_type)
 /*
  * The following are used to control the SPI chip selects for the SPI command.
  */
-#if ((CONFIG_COMMANDS & CFG_CMD_SPI) || defined(CONFIG_CMD_SPI)) && CONFIG_NIOS_SPI
+#if defined(CONFIG_CMD_SPI) && CONFIG_NIOS_SPI
 
 #define	SPI_RTC_CS_MASK	0x00000001
 

board/ssv/common/cmd_sled.c

@@ -46,7 +46,7 @@ typedef struct {
 
 extern led_dev_t led_dev[];
 
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 int do_sled (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
 {
 	int led_id = 0;

board/ssv/common/wd_pio.c

@@ -112,7 +112,7 @@ void hw_watchdog_reset(void)
 		enable_interrupts ();
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 int do_wd (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
 	nios_pio_t *ena_piop	 = (nios_pio_t*)CONFIG_HW_WDENA_BASE;

board/stxxtc/stxxtc.c

@@ -574,7 +574,7 @@ int board_early_init_f(void)
 	return 0;
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 
 #include <linux/mtd/nand_legacy.h>
 

board/svm_sc8xx/svm_sc8xx.c

@@ -153,7 +153,7 @@ long int initdram (int board_type)
 	return (size_b0 );
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_DOC) || defined(CONFIG_CMD_DOC)
+#if defined(CONFIG_CMD_DOC)
 extern void doc_probe (ulong physadr);
 void doc_init (void)
 {

board/tqm5200/cmd_stk52xx.c

@@ -29,7 +29,7 @@
 #include <common.h>
 #include <command.h>
 
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 
 #if defined(CONFIG_STK52XX) || defined(CONFIG_FO300)
 #define DEFAULT_VOL	45

board/tqm5200/cmd_tb5200.c

@@ -29,7 +29,7 @@
 #include <common.h>
 #include <command.h>
 
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 #if defined (CONFIG_TB5200)
 
 #define SM501_PANEL_DISPLAY_CONTROL	0x00080000UL

board/tqm8272/tqm8272.c

@@ -1065,7 +1065,7 @@ int update_flash_size (int flash_size)
 }
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 
 #include <nand.h>
 #include <linux/mtd/mtd.h>

board/trab/auto_update.c

@@ -46,7 +46,7 @@
 #error "must define CFG_HUSH_PARSER"
 #endif
 
-#if !((CONFIG_COMMANDS & CFG_CMD_FAT) || defined(CONFIG_CMD_FAT))
+#if !defined(CONFIG_CMD_FAT)
 #error "must define CFG_CMD_FAT"
 #endif
 

board/trab/cmd_trab.c

@@ -32,7 +32,7 @@
  * TRAB board specific commands. Especially commands for burn-in and function
  * test.
  */
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 
 /* limits for valid range of VCC5V in mV  */
 #define VCC5V_MIN       4500
@@ -846,7 +846,7 @@ int do_temp_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
 	int contact_temp;
 	int delay = 0;
-#if (CONFIG_COMMANDS & CFG_CMD_DATE) || defined(CONFIG_CMD_DATE)
+#if defined(CONFIG_CMD_DATE)
 	struct rtc_time tm;
 #endif
 
@@ -862,7 +862,7 @@ int do_temp_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	spi_init ();
 	while (1) {
 
-#if (CONFIG_COMMANDS & CFG_CMD_DATE) || defined(CONFIG_CMD_DATE)
+#if defined(CONFIG_CMD_DATE)
 		rtc_get (&tm);
 		printf ("%4d-%02d-%02d %2d:%02d:%02d - ",
 			tm.tm_year, tm.tm_mon, tm.tm_mday,

board/trab/trab_fkt.c

@@ -148,7 +148,7 @@ static int rs485_receive_chars (char *data, int timeout);
 static unsigned short updcrc(unsigned short icrc, unsigned char *icp,
 			     unsigned int icnt);
 
-#if (CONFIG_COMMANDS & CFG_CMD_I2C) || defined(CONFIG_CMD_I2C)
+#if defined(CONFIG_CMD_I2C)
 static int trab_eeprom_read (char **argv);
 static int trab_eeprom_write (char **argv);
 int i2c_write_multiple (uchar chip, uint addr, int alen, uchar *buffer,
@@ -959,7 +959,7 @@ static int touch_check_pressed (void)
 
 static int touch_write_clibration_values (int calib_point, int x, int y)
 {
-#if (CONFIG_COMMANDS & CFG_CMD_I2C) || defined(CONFIG_CMD_I2C)
+#if defined(CONFIG_CMD_I2C)
 	int x_verify = 0;
 	int y_verify = 0;
 
@@ -1105,7 +1105,7 @@ static int rs485_receive_chars (char *data, int timeout)
 
 int do_serial_number (char **argv)
 {
-#if (CONFIG_COMMANDS & CFG_CMD_I2C) || defined(CONFIG_CMD_I2C)
+#if defined(CONFIG_CMD_I2C)
 	unsigned int serial_number;
 
 	if (strcmp (argv[2], "read") == 0) {
@@ -1139,7 +1139,7 @@ int do_serial_number (char **argv)
 
 int do_crc16 (void)
 {
-#if (CONFIG_COMMANDS & CFG_CMD_I2C) || defined(CONFIG_CMD_I2C)
+#if defined(CONFIG_CMD_I2C)
 	int crc;
 	unsigned char buf[EEPROM_MAX_CRC_BUF];
 
@@ -1260,7 +1260,7 @@ int do_gain (char **argv)
 
 int do_eeprom (char **argv)
 {
-#if (CONFIG_COMMANDS & CFG_CMD_I2C) || defined(CONFIG_CMD_I2C)
+#if defined(CONFIG_CMD_I2C)
 	if (strcmp (argv[2], "read") == 0) {
 		return (trab_eeprom_read (argv));
 	}
@@ -1278,7 +1278,7 @@ int do_eeprom (char **argv)
 #endif /* CFG_CMD_I2C */
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_I2C) || defined(CONFIG_CMD_I2C)
+#if defined(CONFIG_CMD_I2C)
 static int trab_eeprom_read (char **argv)
 {
 	int i;

board/uc100/pcmcia.c

@@ -4,11 +4,11 @@
 
 #undef	CONFIG_PCMCIA
 
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) || defined(CONFIG_CMD_PCMCIA)
+#if defined(CONFIG_CMD_PCMCIA)
 #define	CONFIG_PCMCIA
 #endif
 
-#if ((CONFIG_COMMANDS & CFG_CMD_IDE) || defined(CONFIG_CMD_IDE)) && defined(CONFIG_IDE_8xx_PCCARD)
+#if (defined(CONFIG_CMD_IDE)) && defined(CONFIG_IDE_8xx_PCCARD)
 #define	CONFIG_PCMCIA
 #endif
 
@@ -123,7 +123,7 @@ int pcmcia_hardware_enable(int slot)
 }
 
 
-#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA) || defined(CONFIG_CMD_PCMCIA)
+#if defined(CONFIG_CMD_PCMCIA)
 int pcmcia_hardware_disable(int slot)
 {
 	volatile immap_t	*immap;

board/w7o/cmd_vpd.c

@@ -24,7 +24,7 @@
 #include <common.h>
 #include <command.h>
 
-#if (CONFIG_COMMANDS & CFG_CMD_BSP) || defined(CONFIG_CMD_BSP)
+#if defined(CONFIG_CMD_BSP)
 
 #include "vpd.h"
 
@@ -63,4 +63,4 @@ U_BOOT_CMD(
 	  "        - Read VPD Data from default address, or device address 'dev_addr'.\n"
 );
 
-#endif /* (CONFIG_COMMANDS & CFG_CMD_BSP) */
+#endif

board/xilinx/ml300/serial.c

@@ -122,7 +122,7 @@ serial_puts(const char *s)
 	}
 }
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB) || defined(CONFIG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 void
 kgdb_serial_init(void)
 {

board/zylonite/nand.c

@@ -22,7 +22,7 @@
 
 #include <common.h>
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND) || defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
 #ifdef CONFIG_NEW_NAND_CODE
 
 #include <nand.h>