Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
	drivers/serial/serial_lh7a40x.c

Signed-off-by: Tom Rini <trini@ti.com>

MAINTAINERS

@@ -583,6 +583,10 @@ Stefano Babic <sbabic@denx.de>
 	twister		omap3
  	vision2		i.MX51
 
+Lukasz Dalek <luk0104@gmail.com>
+
+	h2200		xscale/pxa
+
 Jason Liu <r64343@freescale.com>
 
 	mx53evk         i.MX53

arch/arm/cpu/arm1176/tnetv107x/Makefile

@@ -21,7 +21,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(SOC).o
 
-COBJS	+= aemif.o clock.o init.o mux.o timer.o wdt.o
+COBJS	+= aemif.o clock.o init.o mux.o timer.o
 SOBJS	+= lowlevel_init.o
 
 SRCS	:= $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)

arch/arm/cpu/arm920t/s3c24x0/Makefile

@@ -29,9 +29,6 @@ COBJS-$(CONFIG_USE_IRQ) += interrupts.o
 COBJS-$(CONFIG_DISPLAY_CPUINFO)	+= cpu_info.o
 COBJS-y	+= speed.o
 COBJS-y	+= timer.o
-COBJS-y	+= usb.o
-COBJS-y	+= usb_ohci.o
-
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
 OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))

arch/arm/cpu/arm920t/s3c24x0/usb.c

@@ -1,71 +0,0 @@
-/*
- * (C) Copyright 2006
- * DENX Software Engineering <mk@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#if defined(CONFIG_USB_OHCI_NEW) && \
-    defined(CONFIG_SYS_USB_OHCI_CPU_INIT) && \
-    defined(CONFIG_S3C24X0)
-
-#include <asm/arch/s3c24x0_cpu.h>
-#include <asm/io.h>
-
-int usb_cpu_init(void)
-{
-	struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
-	struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio();
-
-	/*
-	 * Set the 48 MHz UPLL clocking. Values are taken from
-	 * "PLL value selection guide", 6-23, s3c2400_UM.pdf.
-	 */
-	writel((40 << 12) + (1 << 4) + 2, &clk_power->upllcon);
-	/* 1 = use pads related USB for USB host */
-	writel(readl(&gpio->misccr) | 0x8, &gpio->misccr);
-
-	/*
-	 * Enable USB host clock.
-	 */
-	writel(readl(&clk_power->clkcon) | (1 << 4), &clk_power->clkcon);
-
-	return 0;
-}
-
-int usb_cpu_stop(void)
-{
-	struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
-	/* may not want to do this */
-	writel(readl(&clk_power->clkcon) & ~(1 << 4), &clk_power->clkcon);
-	return 0;
-}
-
-int usb_cpu_init_fail(void)
-{
-	struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
-	writel(readl(&clk_power->clkcon) & ~(1 << 4), &clk_power->clkcon);
-	return 0;
-}
-
-#endif /* defined(CONFIG_USB_OHCI_NEW) && \
-	   defined(CONFIG_SYS_USB_OHCI_CPU_INIT) && \
-	   defined(CONFIG_S3C24X0) */

arch/arm/cpu/lh7a40x/config.mk

@@ -1,33 +0,0 @@
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-PLATFORM_RELFLAGS += -fno-common -ffixed-r8 -msoft-float
-
-PLATFORM_CPPFLAGS += -march=armv4
-# =========================================================================
-#
-# Supply options according to compiler version
-#
-# ========================================================================
-PF_RELFLAGS_SLB_AT := $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,))
-PLATFORM_RELFLAGS += $(PF_RELFLAGS_SLB_AT)

arch/arm/cpu/lh7a40x/cpu.c

@@ -1,65 +0,0 @@
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * CPU specific code
- */
-
-#include <common.h>
-#include <command.h>
-#include <asm/system.h>
-
-static void cache_flush(void);
-
-int cleanup_before_linux (void)
-{
-	/*
-	 * this function is called just before we call linux
-	 * it prepares the processor for linux
-	 *
-	 * we turn off caches etc ...
-	 */
-
-	disable_interrupts ();
-
-	/* turn off I/D-cache */
-	icache_disable();
-	dcache_disable();
-
-	/* flush I/D-cache */
-	cache_flush();
-
-	return 0;
-}
-
-/* flush I/D-cache */
-static void cache_flush (void)
-{
-	unsigned long i = 0;
-
-	asm ("mcr p15, 0, %0, c7, c7, 0": :"r" (i));
-}

arch/arm/cpu/lh7a40x/speed.c

@@ -1,83 +0,0 @@
-/*
- * (C) Copyright 2001-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, d.mueller@elsoft.ch
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <lh7a40x.h>
-
-
-/* ------------------------------------------------------------------------- */
-/* NOTE: This describes the proper use of this file.
- *
- * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL.
- *
- * get_FCLK(), get_HCLK(), get_PCLK() return the clock of
- * the specified bus in HZ.
- */
-/* ------------------------------------------------------------------------- */
-
-ulong get_PLLCLK (void)
-{
-	return CONFIG_SYS_CLK_FREQ;
-}
-
-/* return FCLK frequency */
-ulong get_FCLK (void)
-{
-	lh7a40x_csc_t* csc = LH7A40X_CSC_PTR;
-	ulong maindiv1, maindiv2, prediv, ps;
-
-	/*
-	 * from userguide 6.1.1.2
-	 *
-	 * FCLK = ((MAINDIV1 +2) * (MAINDIV2 +2) * 14.7456MHz) /
-	 *                   ((PREDIV+2) * (2^PS))
-	 */
-	maindiv2 = (csc->clkset & CLKSET_MAINDIV2) >> 11;
-	maindiv1 = (csc->clkset & CLKSET_MAINDIV1) >> 7;
-	prediv = (csc->clkset & CLKSET_PREDIV) >> 2;
-	ps = (csc->clkset & CLKSET_PS) >> 16;
-
-	return (((maindiv2 + 2) * (maindiv1 + 2) * CONFIG_SYS_CLK_FREQ) /
-		((prediv + 2) * (1 << ps)));
-}
-
-
-/* return HCLK frequency */
-ulong get_HCLK (void)
-{
-	lh7a40x_csc_t* csc = LH7A40X_CSC_PTR;
-
-	return (get_FCLK () / ((csc->clkset & CLKSET_HCLKDIV) + 1));
-}
-
-/* return PCLK frequency */
-ulong get_PCLK (void)
-{
-	lh7a40x_csc_t* csc = LH7A40X_CSC_PTR;
-
-	return (get_HCLK () /
-		(1 << (((csc->clkset & CLKSET_PCLKDIV) >> 16) + 1)));
-}

arch/arm/cpu/lh7a40x/start.S

@@ -1,506 +0,0 @@
-/*
- *  armboot - Startup Code for ARM920 CPU-core
- *
- *  Copyright (c) 2001	Marius Gröger <mag@sysgo.de>
- *  Copyright (c) 2002	Alex Züpke <azu@sysgo.de>
- *  Copyright (c) 2002	Gary Jennejohn <garyj@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <asm-offsets.h>
-#include <config.h>
-#include <version.h>
-
-/*
- *************************************************************************
- *
- * Jump vector table as in table 3.1 in [1]
- *
- *************************************************************************
- */
-
-
-.globl _start
-_start:	b       reset
-	ldr	pc, _undefined_instruction
-	ldr	pc, _software_interrupt
-	ldr	pc, _prefetch_abort
-	ldr	pc, _data_abort
-	ldr	pc, _not_used
-	ldr	pc, _irq
-	ldr	pc, _fiq
-
-_undefined_instruction:	.word undefined_instruction
-_software_interrupt:	.word software_interrupt
-_prefetch_abort:	.word prefetch_abort
-_data_abort:		.word data_abort
-_not_used:		.word not_used
-_irq:			.word irq
-_fiq:			.word fiq
-
-	.balignl 16,0xdeadbeef
-
-
-/*
- *************************************************************************
- *
- * Startup Code (reset vector)
- *
- * do important init only if we don't start from memory!
- * relocate armboot to ram
- * setup stack
- * jump to second stage
- *
- *************************************************************************
- */
-
-.globl _TEXT_BASE
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE
-
-/*
- * These are defined in the board-specific linker script.
- * Subtracting _start from them lets the linker put their
- * relative position in the executable instead of leaving
- * them null.
- */
-.globl _bss_start_ofs
-_bss_start_ofs:
-	.word __bss_start - _start
-
-.globl _bss_end_ofs
-_bss_end_ofs:
-	.word __bss_end__ - _start
-
-.globl _end_ofs
-_end_ofs:
-	.word _end - _start
-
-#ifdef CONFIG_USE_IRQ
-/* IRQ stack memory (calculated at run-time) */
-.globl IRQ_STACK_START
-IRQ_STACK_START:
-	.word	0x0badc0de
-
-/* IRQ stack memory (calculated at run-time) */
-.globl FIQ_STACK_START
-FIQ_STACK_START:
-	.word 0x0badc0de
-#endif
-
-/* IRQ stack memory (calculated at run-time) + 8 bytes */
-.globl IRQ_STACK_START_IN
-IRQ_STACK_START_IN:
-	.word	0x0badc0de
-
-/*
- * the actual reset code
- */
-
-reset:
-	/*
-	 * set the cpu to SVC32 mode
-	 */
-	mrs	r0,cpsr
-	bic	r0,r0,#0x1f
-	orr	r0,r0,#0xd3
-	msr	cpsr,r0
-
-#define pWDTCTL		0x80001400  /* Watchdog Timer control register */
-#define pINTENC		0x8000050C  /* Interrupt-Controller enable clear register */
-#define pCLKSET		0x80000420  /* clock divisor register */
-
-	/* disable watchdog, set watchdog control register to
-	 * all zeros (default reset)
-	 */
-	ldr     r0, =pWDTCTL
-	mov     r1, #0x0
-	str     r1, [r0]
-
-	/*
-	 * mask all IRQs by setting all bits in the INTENC register (default)
-	 */
-	mov	r1, #0xffffffff
-	ldr	r0, =pINTENC
-	str	r1, [r0]
-
-	/* FCLK:HCLK:PCLK = 1:2:2 */
-	/* default FCLK is 200 MHz, using 14.7456 MHz fin */
-	ldr	r0, =pCLKSET
-	ldr r1, =0x0004ee39
-@	ldr r1, =0x0005ee39	@ 1: 2: 4
-	str	r1, [r0]
-
-	/*
-	 * we do sys-critical inits only at reboot,
-	 * not when booting from ram!
-	 */
-#ifndef CONFIG_SKIP_LOWLEVEL_INIT
-	bl	cpu_init_crit
-#endif
-
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
-	ldr	sp, =(CONFIG_SYS_INIT_SP_ADDR)
-	bic	sp, sp, #7 /* 8-byte alignment for ABI compliance */
-	ldr	r0,=0x00000000
-	bl	board_init_f
-
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- */
-	.globl	relocate_code
-relocate_code:
-	mov	r4, r0	/* save addr_sp */
-	mov	r5, r1	/* save addr of gd */
-	mov	r6, r2	/* save addr of destination */
-
-	/* Set up the stack						    */
-stack_setup:
-	mov	sp, r4
-
-	adr	r0, _start
-	cmp	r0, r6
-	moveq	r9, #0		/* no relocation. relocation offset(r9) = 0 */
-	beq	clear_bss		/* skip relocation */
-	mov	r1, r6			/* r1 <- scratch for copy_loop */
-	ldr	r3, _bss_start_ofs
-	add	r2, r0, r3		/* r2 <- source end address	    */
-
-copy_loop:
-	ldmia	r0!, {r9-r10}		/* copy from source address [r0]    */
-	stmia	r1!, {r9-r10}		/* copy to   target address [r1]    */
-	cmp	r0, r2			/* until source end address [r2]    */
-	blo	copy_loop
-
-#ifndef CONFIG_SPL_BUILD
-	/*
-	 * fix .rel.dyn relocations
-	 */
-	ldr	r0, _TEXT_BASE		/* r0 <- Text base */
-	sub	r9, r6, r0		/* r9 <- relocation offset */
-	ldr	r10, _dynsym_start_ofs	/* r10 <- sym table ofs */
-	add	r10, r10, r0		/* r10 <- sym table in FLASH */
-	ldr	r2, _rel_dyn_start_ofs	/* r2 <- rel dyn start ofs */
-	add	r2, r2, r0		/* r2 <- rel dyn start in FLASH */
-	ldr	r3, _rel_dyn_end_ofs	/* r3 <- rel dyn end ofs */
-	add	r3, r3, r0		/* r3 <- rel dyn end in FLASH */
-fixloop:
-	ldr	r0, [r2]		/* r0 <- location to fix up, IN FLASH! */
-	add	r0, r0, r9		/* r0 <- location to fix up in RAM */
-	ldr	r1, [r2, #4]
-	and	r7, r1, #0xff
-	cmp	r7, #23			/* relative fixup? */
-	beq	fixrel
-	cmp	r7, #2			/* absolute fixup? */
-	beq	fixabs
-	/* ignore unknown type of fixup */
-	b	fixnext
-fixabs:
-	/* absolute fix: set location to (offset) symbol value */
-	mov	r1, r1, LSR #4		/* r1 <- symbol index in .dynsym */
-	add	r1, r10, r1		/* r1 <- address of symbol in table */
-	ldr	r1, [r1, #4]		/* r1 <- symbol value */
-	add	r1, r1, r9		/* r1 <- relocated sym addr */
-	b	fixnext
-fixrel:
-	/* relative fix: increase location by offset */
-	ldr	r1, [r0]
-	add	r1, r1, r9
-fixnext:
-	str	r1, [r0]
-	add	r2, r2, #8		/* each rel.dyn entry is 8 bytes */
-	cmp	r2, r3
-	blo	fixloop
-#endif
-
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
-	ldr	r0, _bss_start_ofs
-	ldr	r1, _bss_end_ofs
-	mov	r4, r6			/* reloc addr */
-	add	r0, r0, r4
-	add	r1, r1, r4
-	mov	r2, #0x00000000		/* clear			    */
-
-clbss_l:cmp	r0, r1			/* clear loop... */
-	bhs	clbss_e			/* if reached end of bss, exit */
-	str	r2, [r0]
-	add	r0, r0, #4
-	b	clbss_l
-clbss_e:
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-	ldr	r0, _board_init_r_ofs
-	adr	r1, _start
-	add	lr, r0, r1
-	add	lr, lr, r9
-	/* setup parameters for board_init_r */
-	mov	r0, r5		/* gd_t */
-	mov	r1, r6		/* dest_addr */
-	/* jump to it ... */
-	mov	pc, lr
-
-_board_init_r_ofs:
-	.word board_init_r - _start
-
-_rel_dyn_start_ofs:
-	.word __rel_dyn_start - _start
-_rel_dyn_end_ofs:
-	.word __rel_dyn_end - _start
-_dynsym_start_ofs:
-	.word __dynsym_start - _start
-
-/*
- *************************************************************************
- *
- * CPU_init_critical registers
- *
- * setup important registers
- * setup memory timing
- *
- *************************************************************************
- */
-
-
-cpu_init_crit:
-	/*
-	 * flush v4 I/D caches
-	 */
-	mov	r0, #0
-	mcr	p15, 0, r0, c7, c7, 0	/* flush v3/v4 cache */
-	mcr	p15, 0, r0, c8, c7, 0	/* flush v4 TLB */
-
-	/*
-	 * disable MMU stuff and caches
-	 */
-	mrc	p15, 0, r0, c1, c0, 0
-	bic	r0, r0, #0x00002300	@ clear bits 13, 9:8 (--V- --RS)
-	bic	r0, r0, #0x00000087	@ clear bits 7, 2:0 (B--- -CAM)
-	orr	r0, r0, #0x00000002	@ set bit 2 (A) Align
-	orr	r0, r0, #0x00001000	@ set bit 12 (I) I-Cache
-	orr	r0, r0, #0x40000000	@ set bit 30 (nF) notFastBus
-	mcr	p15, 0, r0, c1, c0, 0
-
-
-	/*
-	 * before relocating, we have to setup RAM timing
-	 * because memory timing is board-dependend, you will
-	 * find a lowlevel_init.S in your board directory.
-	 */
-	mov	ip, lr
-	bl	lowlevel_init
-	mov	lr, ip
-
-	mov	pc, lr
-
-
-/*
- *************************************************************************
- *
- * Interrupt handling
- *
- *************************************************************************
- */
-
-@
-@ IRQ stack frame.
-@
-#define S_FRAME_SIZE	72
-
-#define S_OLD_R0	68
-#define S_PSR		64
-#define S_PC		60
-#define S_LR		56
-#define S_SP		52
-
-#define S_IP		48
-#define S_FP		44
-#define S_R10		40
-#define S_R9		36
-#define S_R8		32
-#define S_R7		28
-#define S_R6		24
-#define S_R5		20
-#define S_R4		16
-#define S_R3		12
-#define S_R2		8
-#define S_R1		4
-#define S_R0		0
-
-#define MODE_SVC 0x13
-#define I_BIT	 0x80
-
-/*
- * use bad_save_user_regs for abort/prefetch/undef/swi ...
- * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling
- */
-
-	.macro	bad_save_user_regs
-	sub	sp, sp, #S_FRAME_SIZE
-	stmia	sp, {r0 - r12}			@ Calling r0-r12
-	ldr	r2, IRQ_STACK_START_IN
-	ldmia	r2, {r2 - r3}			@ get pc, cpsr
-	add	r0, sp, #S_FRAME_SIZE		@ restore sp_SVC
-
-	add	r5, sp, #S_SP
-	mov	r1, lr
-	stmia	r5, {r0 - r3}			@ save sp_SVC, lr_SVC, pc, cpsr
-	mov	r0, sp
-	.endm
-
-	.macro	irq_save_user_regs
-	sub	sp, sp, #S_FRAME_SIZE
-	stmia	sp, {r0 - r12}			@ Calling r0-r12
-	add     r8, sp, #S_PC
-	stmdb   r8, {sp, lr}^                   @ Calling SP, LR
-	str     lr, [r8, #0]                    @ Save calling PC
-	mrs     r6, spsr
-	str     r6, [r8, #4]                    @ Save CPSR
-	str     r0, [r8, #8]                    @ Save OLD_R0
-	mov	r0, sp
-	.endm
-
-	.macro	irq_restore_user_regs
-	ldmia	sp, {r0 - lr}^			@ Calling r0 - lr
-	mov	r0, r0
-	ldr	lr, [sp, #S_PC]			@ Get PC
-	add	sp, sp, #S_FRAME_SIZE
-	subs	pc, lr, #4			@ return & move spsr_svc into cpsr
-	.endm
-
-	.macro get_bad_stack
-	ldr	r13, IRQ_STACK_START_IN		@ setup our mode stack
-
-	str	lr, [r13]			@ save caller lr / spsr
-	mrs	lr, spsr
-	str     lr, [r13, #4]
-
-	mov	r13, #MODE_SVC			@ prepare SVC-Mode
-	@ msr	spsr_c, r13
-	msr	spsr, r13
-	mov	lr, pc
-	movs	pc, lr
-	.endm
-
-	.macro get_irq_stack			@ setup IRQ stack
-	ldr	sp, IRQ_STACK_START
-	.endm
-
-	.macro get_fiq_stack			@ setup FIQ stack
-	ldr	sp, FIQ_STACK_START
-	.endm
-
-/*
- * exception handlers
- */
-	.align  5
-undefined_instruction:
-	get_bad_stack
-	bad_save_user_regs
-	bl	do_undefined_instruction
-
-	.align	5
-software_interrupt:
-	get_bad_stack
-	bad_save_user_regs
-	bl	do_software_interrupt
-
-	.align	5
-prefetch_abort:
-	get_bad_stack
-	bad_save_user_regs
-	bl	do_prefetch_abort
-
-	.align	5
-data_abort:
-	get_bad_stack
-	bad_save_user_regs
-	bl	do_data_abort
-
-	.align	5
-not_used:
-	get_bad_stack
-	bad_save_user_regs
-	bl	do_not_used
-
-#ifdef CONFIG_USE_IRQ
-
-	.align	5
-irq:
-	get_irq_stack
-	irq_save_user_regs
-	bl	do_irq
-	irq_restore_user_regs
-
-	.align	5
-fiq:
-	get_fiq_stack
-	/* someone ought to write a more effiction fiq_save_user_regs */
-	irq_save_user_regs
-	bl	do_fiq
-	irq_restore_user_regs
-
-#else
-
-	.align	5
-irq:
-	get_bad_stack
-	bad_save_user_regs
-	bl	do_irq
-
-	.align	5
-fiq:
-	get_bad_stack
-	bad_save_user_regs
-	bl	do_fiq
-
-#endif
-
-	.align	5
-.globl reset_cpu
-reset_cpu:
-	bl	disable_interrupts
-
-	/* Disable watchdog */
-	ldr	r1, =pWDTCTL
-	mov	r3, #0
-	str	r3, [r1]
-
-	/* reset counter */
-	ldr	r3, =0x00001984
-	str	r3, [r1, #4]
-
-	/* Enable the watchdog */
-	mov	r3, #1
-	str	r3, [r1]
-
-_loop_forever:
-	b	_loop_forever

arch/arm/cpu/lh7a40x/timer.c

@@ -1,182 +0,0 @@
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Alex Zuepke <azu@sysgo.de>
- *
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <lh7a40x.h>
-
-static ulong timer_load_val = 0;
-
-/* macro to read the 16 bit timer */
-static inline ulong READ_TIMER(void)
-{
-	lh7a40x_timers_t* timers = LH7A40X_TIMERS_PTR;
-	lh7a40x_timer_t* timer = &timers->timer1;
-
-	return (timer->value & 0x0000ffff);
-}
-
-static ulong timestamp;
-static ulong lastdec;
-
-int timer_init (void)
-{
-	lh7a40x_timers_t* timers = LH7A40X_TIMERS_PTR;
-	lh7a40x_timer_t* timer = &timers->timer1;
-
-	/* a periodic timer using the 508kHz source */
-	timer->control = (TIMER_PER | TIMER_CLK508K);
-
-	if (timer_load_val == 0) {
-		/*
-		 * 10ms period with 508.469kHz clock = 5084
-		 */
-		timer_load_val = CONFIG_SYS_HZ/100;
-	}
-
-	/* load value for 10 ms timeout */
-	lastdec = timer->load = timer_load_val;
-
-	/* auto load, start timer */
-	timer->control = timer->control | TIMER_EN;
-	timestamp = 0;
-
-	return (0);
-}
-
-/*
- * timer without interrupts
- */
-ulong get_timer (ulong base)
-{
-	return (get_timer_masked() - base);
-}
-
-void __udelay (unsigned long usec)
-{
-	ulong tmo,tmp;
-
-	/* normalize */
-	if (usec >= 1000) {
-		tmo = usec / 1000;
-		tmo *= CONFIG_SYS_HZ;
-		tmo /= 1000;
-	}
-	else {
-		if (usec > 1) {
-			tmo = usec * CONFIG_SYS_HZ;
-			tmo /= (1000*1000);
-		}
-		else
-			tmo = 1;
-	}
-
-	/* check for rollover during this delay */
-	tmp = get_timer (0);
-	if ((tmp + tmo) < tmp )
-		reset_timer_masked();  /* timer would roll over */
-	else
-		tmo += tmp;
-
-	while (get_timer_masked () < tmo);
-}
-
-void reset_timer_masked (void)
-{
-	/* reset time */
-	lastdec = READ_TIMER();
-	timestamp = 0;
-}
-
-ulong get_timer_masked (void)
-{
-	ulong now = READ_TIMER();
-
-	if (lastdec >= now) {
-		/* normal mode */
-		timestamp += (lastdec - now);
-	} else {
-		/* we have an overflow ... */
-		timestamp += ((lastdec + timer_load_val) - now);
-	}
-	lastdec = now;
-
-	return timestamp;
-}
-
-void udelay_masked (unsigned long usec)
-{
-	ulong tmo;
-	ulong endtime;
-	signed long diff;
-
-	/* normalize */
-	if (usec >= 1000) {
-		tmo = usec / 1000;
-		tmo *= CONFIG_SYS_HZ;
-		tmo /= 1000;
-	} else {
-		if (usec > 1) {
-			tmo = usec * CONFIG_SYS_HZ;
-			tmo /= (1000*1000);
-		} else {
-			tmo = 1;
-		}
-	}
-
-	endtime = get_timer_masked () + tmo;
-
-	do {
-		ulong now = get_timer_masked ();
-		diff = endtime - now;
-	} while (diff >= 0);
-}
-
-/*
- * This function is derived from PowerPC code (read timebase as long long).
- * On ARM it just returns the timer value.
- */
-unsigned long long get_ticks(void)
-{
-	return get_timer(0);
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk (void)
-{
-	ulong tbclk;
-
-	tbclk = timer_load_val * 100;
-
-	return tbclk;
-}

arch/arm/lib/board.c

@@ -274,6 +274,8 @@ void board_init_f(ulong bootflag)
 #ifdef CONFIG_PRAM
 	ulong reg;
 #endif
+	void *new_fdt = NULL;
+	size_t fdt_size = 0;
 
 	bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_F, "board_init_f");
 
@@ -409,6 +411,22 @@ void board_init_f(ulong bootflag)
 	debug("Reserving %zu Bytes for Global Data at: %08lx\n",
 			sizeof (gd_t), addr_sp);
 
+#if defined(CONFIG_OF_SEPARATE) && defined(CONFIG_OF_CONTROL)
+	/*
+	 * If the device tree is sitting immediate above our image then we
+	 * must relocate it. If it is embedded in the data section, then it
+	 * will be relocated with other data.
+	 */
+	if (gd->fdt_blob) {
+		fdt_size = ALIGN(fdt_totalsize(gd->fdt_blob) + 0x1000, 32);
+
+		addr_sp -= fdt_size;
+		new_fdt = (void *)addr_sp;
+		debug("Reserving %zu Bytes for FDT at: %08lx\n",
+		      fdt_size, addr_sp);
+	}
+#endif
+
 	/* setup stackpointer for exeptions */
 	gd->irq_sp = addr_sp;
 #ifdef CONFIG_USE_IRQ
@@ -442,6 +460,10 @@ void board_init_f(ulong bootflag)
 	gd->start_addr_sp = addr_sp;
 	gd->reloc_off = addr - _TEXT_BASE;
 	debug("relocation Offset is: %08lx\n", gd->reloc_off);
+	if (new_fdt) {
+		memcpy(new_fdt, gd->fdt_blob, fdt_size);
+		gd->fdt_blob = new_fdt;
+	}
 	memcpy(id, (void *)gd, sizeof(gd_t));
 
 	relocate_code(addr_sp, id, addr);

board/actux1/u-boot.lds

@@ -34,7 +34,7 @@ SECTIONS
 		net/libnet.o(.text*)
 		board/actux1/libactux1.o(.text*)
 		arch/arm/cpu/ixp/libixp.o(.text*)
-		drivers/serial/libserial.o(.text*)
+		drivers/input/libinput.o(.text*)
 
 		. = env_offset;
 		common/env_embedded.o(.ppcenv)

board/actux2/u-boot.lds

@@ -34,7 +34,7 @@ SECTIONS
 		net/libnet.o(.text*)
 		board/actux2/libactux2.o(.text*)
 		arch/arm/cpu/ixp/libixp.o(.text*)
-		drivers/serial/libserial.o(.text*)
+		drivers/input/libinput.o(.text*)
 
 		. = env_offset;
 		common/env_embedded.o(.ppcenv)

board/actux3/u-boot.lds

@@ -34,7 +34,7 @@ SECTIONS
 		net/libnet.o(.text*)
 		board/actux3/libactux3.o(.text*)
 		arch/arm/cpu/ixp/libixp.o(.text*)
-		drivers/serial/libserial.o(.text*)
+		drivers/input/libinput.o(.text*)
 
 		. = env_offset;
 		common/env_embedded.o(.ppcenv)

arch/arm/cpu/lh7a40x/Makefile → board/h2200/Makefile

@@ -1,9 +1,7 @@
 #
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+# h2200 Support
 #
-# See file CREDITS for list of people who contributed to this
-# project.
+# Copyright (C) 2012 Lukasz Dalek <luk0104@gmail.com>
 #
 # This program is free software; you can redistribute it and/or
 # modify it under the terms of the GNU General Public License as
@@ -23,18 +21,22 @@
 
 include $(TOPDIR)/config.mk
 
-LIB	= $(obj)lib$(CPU).o
+LIB	= $(obj)lib$(BOARD).o
 
-START	= start.o
-COBJS	= cpu.o speed.o timer.o
+COBJS	:= h2200.o
 
-SRCS	:= $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
-START	:= $(addprefix $(obj),$(START))
+SRCS	:= $(COBJS:.o=.c) h2200-header.S
+OBJS	:= $(addprefix $(obj),$(COBJS))
 
-all:	$(obj).depend $(START) $(LIB)
+all: $(LIB) $(obj)h2200-header.bin
 
-$(LIB):	$(OBJS)
+$(obj)h2200-header.o: h2200-header.S
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+$(obj)h2200-header.bin: $(obj)h2200-header.o
+	$(OBJCOPY) -O binary $< $@
+
+$(LIB):	$(obj).depend $(OBJS)
 	$(call cmd_link_o_target, $(OBJS))
 
 #########################################################################

board/h2200/h2200-header.S

@@ -0,0 +1,27 @@
+/*
+ * iPAQ h2200 header
+ *
+ * Copyright (C) 2012 Lukasz Dalek <luk0104@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+	.word 0xea0003fe /* b 0x1000 */
+
+	.org 0x40
+	.ascii "ECEC"
+
+	.org 0x1000 - 1
+	.byte 0x0

board/h2200/h2200.c

@@ -0,0 +1,53 @@
+/*
+ * iPAQ h2200 board configuration
+ *
+ * Copyright (C) 2012 Lukasz Dalek <luk0104@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <common.h>
+#include <asm/arch/pxa.h>
+#include <asm/arch/pxa-regs.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+	/* We have RAM, disable cache */
+	dcache_disable();
+	icache_disable();
+
+	gd->bd->bi_arch_number = MACH_TYPE_H2200;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0xa0000100;
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	/*
+	 * Everything except MSC0 was already set up by
+	 * 1st stage bootloader.
+	 *
+	 * This setting enables access to companion chip.
+	 */
+	clrsetbits_le32(MSC0, 0xffffffff, CONFIG_SYS_MSC0_VAL);
+	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+	return 0;
+}

boards.cfg

@@ -295,6 +295,7 @@ dvlhost                      arm         ixp
 pdnb3                        arm         ixp         pdnb3               prodrive
 scpu                         arm         ixp         pdnb3               prodrive       -           pdnb3:SCPU
 balloon3                     arm         pxa
+h2200                        arm         pxa
 lubbock                      arm         pxa
 palmld                       arm         pxa
 palmtc                       arm         pxa

doc/driver-model/UDM-serial.txt

@@ -125,67 +125,63 @@ III) Analysis of in-tree drivers
   -------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  17) serial_lh7a40x.c
+  17) serial_lpc2292.c
   --------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  18) serial_lpc2292.c
+  18) serial_max3100.c
   --------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  19) serial_max3100.c
-  --------------------
-  No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
-
-  20) serial_mxc.c
+  19) serial_mxc.c
   ----------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  21) serial_netarm.c
+  20) serial_netarm.c
   -------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  22) serial_pl01x.c
+  21) serial_pl01x.c
   ------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible, though this
   driver in fact contains two drivers in total.
 
-  23) serial_pxa.c
+  22) serial_pxa.c
   ----------------
   This driver is a bit complicated, but due to clean support for
   CONFIG_SERIAL_MULTI, there are no expected obstructions throughout the
   conversion process.
 
-  24) serial_s3c24x0.c
+  23) serial_s3c24x0.c
   --------------------
   This driver, being quite ad-hoc might need some work to bring back to shape.
 
-  25) serial_s3c44b0.c
+  24) serial_s3c44b0.c
   --------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  26) serial_s5p.c
+  25) serial_s5p.c
   ----------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  27) serial_sa1100.c
+  26) serial_sa1100.c
   -------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  28) serial_sh.c
+  27) serial_sh.c
   ---------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  29) serial_xuartlite.c
+  28) serial_xuartlite.c
   ----------------------
   No support for CONFIG_SERIAL_MULTI. Simple conversion possible.
 
-  30) usbtty.c
+  29) usbtty.c
   ------------
   This driver seems very complicated and entangled with USB framework. The
   conversion might be complicated here.
 
-  31) arch/powerpc/cpu/mpc512x/serial.c
+  30) arch/powerpc/cpu/mpc512x/serial.c
   -------------------------------------
   This driver supports CONFIG_SERIAL_MULTI. This driver will need to be moved to
   proper place.

drivers/serial/Makefile

@@ -45,7 +45,6 @@ COBJS-$(CONFIG_IMX_SERIAL) += serial_imx.o
 COBJS-$(CONFIG_IXP_SERIAL) += serial_ixp.o
 COBJS-$(CONFIG_KS8695_SERIAL) += serial_ks8695.o
 COBJS-$(CONFIG_LPC2292_SERIAL) += serial_lpc2292.o
-COBJS-$(CONFIG_LH7A40X_SERIAL) += serial_lh7a40x.o
 COBJS-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o
 COBJS-$(CONFIG_MXC_UART) += serial_mxc.o
 COBJS-$(CONFIG_NETARM_SERIAL) += serial_netarm.o

drivers/serial/serial_lh7a40x.c

@@ -1,197 +0,0 @@
-/*
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#include <common.h>
-#include <lh7a40x.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_CONSOLE_UART1)
-# define UART_CONSOLE 1
-#elif defined(CONFIG_CONSOLE_UART2)
-# define UART_CONSOLE 2
-#elif defined(CONFIG_CONSOLE_UART3)
-# define UART_CONSOLE 3
-#else
-# error "No console configured ... "
-#endif
-
-static void lh7a40x_serial_setbrg(void)
-{
-	lh7a40x_uart_t* uart = LH7A40X_UART_PTR(UART_CONSOLE);
-	int i;
-	unsigned int reg = 0;
-
-	/*
-	 * userguide 15.1.2.4
-	 *
-	 * BAUDDIV is (UART_REF_FREQ/(16 X BAUD))-1
-	 *
-	 *   UART_REF_FREQ = external system clock input / 2 (Hz)
-	 *   BAUD is desired baudrate (bits/s)
-	 *
-	 *   NOTE: we add (divisor/2) to numerator to round for
-	 *         more precision
-	 */
-	reg = (((get_PLLCLK()/2) + ((16*gd->baudrate)/2)) / (16 * gd->baudrate)) - 1;
-	uart->brcon = reg;
-
-	for (i = 0; i < 100; i++);
-}
-
-/*
- * Initialise the serial port with the given baudrate. The settings
- * are always 8 data bits, no parity, 1 stop bit, no start bits.
- *
- */
-static int lh7a40x_serial_init(void)
-{
-	lh7a40x_uart_t* uart = LH7A40X_UART_PTR(UART_CONSOLE);
-
-	/* UART must be enabled before writing to any config registers */
-	uart->con |= (UART_EN);
-
-#ifdef CONFIG_CONSOLE_UART1
-	/* infrared disabled */
-	uart->con |= UART_SIRD;
-#endif
-	/* loopback disabled */
-	uart->con &= ~(UART_LBE);
-
-	/* modem lines and tx/rx polarities */
-	uart->con &= ~(UART_MXP | UART_TXP | UART_RXP);
-
-	/* FIFO enable, N81 */
-	uart->fcon = (UART_WLEN_8 | UART_FEN | UART_STP2_1);
-
-	/* set baudrate */
-	serial_setbrg ();
-
-	/* enable rx interrupt */
-	uart->inten |= UART_RI;
-
-	return (0);
-}
-
-/*
- * Read a single byte from the serial port. Returns 1 on success, 0
- * otherwise. When the function is succesfull, the character read is
- * written into its argument c.
- */
-static int lh7a40x_serial_getc(void)
-{
-	lh7a40x_uart_t* uart = LH7A40X_UART_PTR(UART_CONSOLE);
-
-	/* wait for character to arrive */
-	while (uart->status & UART_RXFE);
-
-	return(uart->data & 0xff);
-}
-
-#ifdef CONFIG_HWFLOW
-static int hwflow = 0; /* turned off by default */
-int hwflow_onoff(int on)
-{
-	switch(on) {
-	case 0:
-	default:
-		break; /* return current */
-	case 1:
-		hwflow = 1; /* turn on */
-		break;
-	case -1:
-		hwflow = 0; /* turn off */
-		break;
-	}
-	return hwflow;
-}
-#endif
-
-#ifdef CONFIG_MODEM_SUPPORT
-static int be_quiet = 0;
-void disable_putc(void)
-{
-	be_quiet = 1;
-}
-
-void enable_putc(void)
-{
-	be_quiet = 0;
-}
-#endif
-
-
-/*
- * Output a single byte to the serial port.
- */
-static void lh7a40x_serial_putc(const char c)
-{
-	lh7a40x_uart_t* uart = LH7A40X_UART_PTR(UART_CONSOLE);
-
-#ifdef CONFIG_MODEM_SUPPORT
-	if (be_quiet)
-		return;
-#endif
-
-	/* wait for room in the tx FIFO */
-	while (!(uart->status & UART_TXFE));
-
-#ifdef CONFIG_HWFLOW
-	/* Wait for CTS up */
-	while(hwflow && !(uart->status & UART_CTS));
-#endif
-
-	uart->data = c;
-
-	/* If \n, also do \r */
-	if (c == '\n')
-		serial_putc ('\r');
-}
-
-/*
- * Test whether a character is in the RX buffer
- */
-static int lh7a40x_serial_tstc(void)
-{
-	lh7a40x_uart_t* uart = LH7A40X_UART_PTR(UART_CONSOLE);
-
-	return(!(uart->status & UART_RXFE));
-}
-
-static struct serial_device lh7a40x_serial_drv = {
-	.name	= "lh7a40x_serial",
-	.start	= lh7a40x_serial_init,
-	.stop	= NULL,
-	.setbrg	= lh7a40x_serial_setbrg,
-	.putc	= lh7a40x_serial_putc,
-	.puts	= default_serial_puts,
-	.getc	= lh7a40x_serial_getc,
-	.tstc	= lh7a40x_serial_tstc,
-};
-
-void lh7a40x_serial_initialize(void)
-{
-	serial_register(&lh7a40x_serial_drv);
-}
-
-__weak struct serial_device *default_serial_console(void)
-{
-	return &lh7a40x_serial_drv;
-}

drivers/usb/gadget/gadget_chips.h

@@ -58,12 +58,6 @@
 #define	gadget_is_sa1100(g)	0
 #endif
 
-#ifdef CONFIG_USB_GADGET_LH7A40X
-#define	gadget_is_lh7a40x(g)	(!strcmp("lh7a40x_udc", (g)->name))
-#else
-#define	gadget_is_lh7a40x(g)	0
-#endif
-
 /* handhelds.org tree (?) */
 #ifdef CONFIG_USB_GADGET_MQ11XX
 #define	gadget_is_mq11xx(g)	(!strcmp("mq11xx_udc", (g)->name))
@@ -195,33 +189,31 @@ static inline int usb_gadget_controller_number(struct usb_gadget *gadget)
 		return 0x07;
 	else if (gadget_is_omap(gadget))
 		return 0x08;
-	else if (gadget_is_lh7a40x(gadget))
-		return 0x09;
 	else if (gadget_is_n9604(gadget))
-		return 0x10;
+		return 0x09;
 	else if (gadget_is_pxa27x(gadget))
-		return 0x11;
+		return 0x10;
 	else if (gadget_is_s3c2410(gadget))
-		return 0x12;
+		return 0x11;
 	else if (gadget_is_at91(gadget))
-		return 0x13;
+		return 0x12;
 	else if (gadget_is_imx(gadget))
-		return 0x14;
+		return 0x13;
 	else if (gadget_is_musbhsfc(gadget))
-		return 0x15;
+		return 0x14;
 	else if (gadget_is_musbhdrc(gadget))
-		return 0x16;
+		return 0x15;
 	else if (gadget_is_mpc8272(gadget))
-		return 0x17;
+		return 0x16;
 	else if (gadget_is_atmel_usba(gadget))
-		return 0x18;
+		return 0x17;
 	else if (gadget_is_fsl_usb2(gadget))
-		return 0x19;
+		return 0x18;
 	else if (gadget_is_amd5536udc(gadget))
-		return 0x20;
+		return 0x19;
 	else if (gadget_is_m66592(gadget))
-		return 0x21;
+		return 0x20;
 	else if (gadget_is_mv(gadget))
-		return 0x22;
+		return 0x21;
 	return -ENOENT;
 }

drivers/usb/host/Makefile

@@ -33,6 +33,7 @@ COBJS-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
 COBJS-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o
 COBJS-$(CONFIG_USB_S3C64XX) += s3c64xx-hcd.o
 COBJS-$(CONFIG_USB_SL811HS) += sl811-hcd.o
+COBJS-$(CONFIG_USB_OHCI_S3C24XX) += ohci-s3c24xx.o
 
 # echi
 COBJS-$(CONFIG_USB_EHCI) += ehci-hcd.o

arch/arm/cpu/arm920t/s3c24x0/usb_ohci.c → drivers/usb/host/ohci-s3c24xx.c

@@ -42,7 +42,7 @@
 #include <asm/io.h>
 #include <malloc.h>
 #include <usb.h>
-#include "usb_ohci.h"
+#include "ohci-s3c24xx.h"
 
 #define OHCI_USE_NPS		/* force NoPowerSwitching mode */
 #undef OHCI_VERBOSE_DEBUG	/* not always helpful */
@@ -1755,3 +1755,47 @@ int usb_lowlevel_stop(int index)
 }
 
 #endif /* defined(CONFIG_USB_OHCI) && defined(CONFIG_S3C24X0) */
+
+#if defined(CONFIG_USB_OHCI_NEW) && \
+    defined(CONFIG_SYS_USB_OHCI_CPU_INIT) && \
+    defined(CONFIG_S3C24X0)
+
+int usb_cpu_init(void)
+{
+	struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
+	struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio();
+
+	/*
+	 * Set the 48 MHz UPLL clocking. Values are taken from
+	 * "PLL value selection guide", 6-23, s3c2400_UM.pdf.
+	 */
+	writel((40 << 12) + (1 << 4) + 2, &clk_power->upllcon);
+	/* 1 = use pads related USB for USB host */
+	writel(readl(&gpio->misccr) | 0x8, &gpio->misccr);
+
+	/*
+	 * Enable USB host clock.
+	 */
+	writel(readl(&clk_power->clkcon) | (1 << 4), &clk_power->clkcon);
+
+	return 0;
+}
+
+int usb_cpu_stop(void)
+{
+	struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
+	/* may not want to do this */
+	writel(readl(&clk_power->clkcon) & ~(1 << 4), &clk_power->clkcon);
+	return 0;
+}
+
+int usb_cpu_init_fail(void)
+{
+	struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
+	writel(readl(&clk_power->clkcon) & ~(1 << 4), &clk_power->clkcon);
+	return 0;
+}
+
+#endif /* defined(CONFIG_USB_OHCI_NEW) && \
+	   defined(CONFIG_SYS_USB_OHCI_CPU_INIT) && \
+	   defined(CONFIG_S3C24X0) */

drivers/watchdog/Makefile

@@ -27,6 +27,7 @@ LIB	:= $(obj)libwatchdog.o
 
 COBJS-$(CONFIG_AT91SAM9_WATCHDOG) += at91sam9_wdt.o
 COBJS-$(CONFIG_FTWDT010_WATCHDOG) += ftwdt010_wdt.o
+COBJS-$(CONFIG_TNETV107X_WATCHDOG) += tnetv107x_wdt.o
 
 COBJS	:= $(COBJS-y)
 SRCS	:= $(COBJS:.o=.c)

include/configs/VCMA9.h

@@ -124,6 +124,7 @@
 
 /* USB support (currently only works with D-cache off) */
 #define CONFIG_USB_OHCI
+#define CONFIG_USB_OHCI_S3C24XX
 #define CONFIG_USB_KEYBOARD
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION

include/configs/ca9x4_ct_vxp.h

@@ -163,6 +163,8 @@
 /* Room required on the stack for the environment data */
 #define CONFIG_ENV_SIZE			FLASH_MAX_SECTOR_SIZE
 
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes */
+
 /*
  * Amount of flash used for environment:
  * We don't know which end has the small erase blocks so we use the penultimate

include/configs/h2200.h

@@ -0,0 +1,157 @@
+/*
+ * iPAQ h2200 board configuration
+ *
+ * Copyright (C) 2012 Lukasz Dalek <luk0104@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define MACH_TYPE_H2200			341
+#define CONFIG_MACH_TYPE		MACH_TYPE_H2200
+
+#define CONFIG_CPU_PXA25X		1
+#define CONFIG_BOARD_H2200
+
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM_1			0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE		0x04000000 /* 64 MB */
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_SDRAM_SIZE		PHYS_SDRAM_1_SIZE
+
+#define CONFIG_SYS_INIT_SP_ADDR		0xfffff800
+
+#define CONFIG_ENV_SIZE			0x00040000
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
+
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_LOAD_ADDR		0xa3000000 /* default load address */
+
+/*
+ * iPAQ 1st stage bootloader loads 2nd stage bootloader
+ * at address 0xa0040000 but bootloader requires header
+ * which is 0x1000 long.
+ *
+ * --- Header begin ---
+ *	.word 0xea0003fe ; b 0x1000
+ *
+ *	.org 0x40
+ *	.ascii "ECEC"
+ *
+ *	.org 0x1000
+ * --- Header end ---
+ */
+
+#define CONFIG_SYS_TEXT_BASE		0xa0041000
+
+/*
+ * Static chips
+ */
+
+#define CONFIG_SYS_MSC0_VAL		0x246c7ffc
+#define CONFIG_SYS_MSC1_VAL		0x7ff07ff0
+#define CONFIG_SYS_MSC2_VAL		0x7ff07ff0
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+
+#define CONFIG_SYS_MECR_VAL		0x00000000
+#define CONFIG_SYS_MCMEM0_VAL		0x00000000
+#define CONFIG_SYS_MCMEM1_VAL		0x00000000
+#define CONFIG_SYS_MCATT0_VAL		0x00000000
+#define CONFIG_SYS_MCATT1_VAL		0x00000000
+#define CONFIG_SYS_MCIO0_VAL		0x00000000
+#define CONFIG_SYS_MCIO1_VAL		0x00000000
+
+#define CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define CONFIG_SYS_SXCNFG_VAL		0x00040004
+
+#define CONFIG_SYS_MDREFR_VAL		0x0099E018
+#define CONFIG_SYS_MDCNFG_VAL		0x01C801CB
+#define CONFIG_SYS_MDMRS_VAL		0x00220022
+
+#define CONFIG_SYS_PSSR_VAL		0x00000000
+#define CONFIG_SYS_CKEN			0x00004840
+#define CONFIG_SYS_CCCR			0x00000161
+
+/*
+ * GPIOs
+ */
+
+#define CONFIG_SYS_GPSR0_VAL		0x01000000
+#define CONFIG_SYS_GPSR1_VAL		0x00000000
+#define CONFIG_SYS_GPSR2_VAL		0x00010000
+
+#define CONFIG_SYS_GPCR0_VAL		0x00000000
+#define CONFIG_SYS_GPCR1_VAL		0x00000000
+#define CONFIG_SYS_GPCR2_VAL		0x00000000
+
+#define CONFIG_SYS_GPDR0_VAL		0xF7E38C00
+#define CONFIG_SYS_GPDR1_VAL		0xBCFFBF83
+#define CONFIG_SYS_GPDR2_VAL		0x000157FF
+
+#define CONFIG_SYS_GAFR0_L_VAL		0x80401000
+#define CONFIG_SYS_GAFR0_U_VAL		0x00000112
+#define CONFIG_SYS_GAFR1_L_VAL		0x600A9550
+#define CONFIG_SYS_GAFR1_U_VAL		0x0005AAAA
+#define CONFIG_SYS_GAFR2_L_VAL		0x20000000
+#define CONFIG_SYS_GAFR2_U_VAL		0x00000000
+
+/*
+ * Serial port
+ */
+
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART
+#define CONFIG_CONS_INDEX		3
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 38400, 115200 }
+
+#define CONFIG_CMD_IMPORTENV		1
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_SOURCE
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_IMI
+
+#define CONFIG_FIT
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_PROMPT		"> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"$ "
+
+/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE		256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+
+#define CONFIG_BOOTARGS "root=/dev/ram0 ro console=ttyS0,115200n8"
+
+#endif /* __CONFIG_H */

include/configs/smdk2410.h

@@ -66,6 +66,7 @@
  * USB support (currently only works with D-cache off)
  ************************************************************/
 #define CONFIG_USB_OHCI
+#define CONFIG_USB_OHCI_S3C24XX
 #define CONFIG_USB_KEYBOARD
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION

include/configs/tnetv107x_evm.h

@@ -32,6 +32,7 @@
 #define CONFIG_ARM1176
 #define CONFIG_TNETV107X
 #define CONFIG_TNETV107X_EVM
+#define CONFIG_TNETV107X_WATCHDOG
 #define CONFIG_ARCH_CPU_INIT
 #define CONFIG_SYS_UBOOT_BASE		CONFIG_SYS_TEXT_BASE
 #define CONFIG_DISABLE_TCM

include/configs/versatile.h

@@ -230,6 +230,7 @@
 #define CONFIG_SYS_FLASH_PROTECTION	/* The devices have real protection */
 #define CONFIG_SYS_FLASH_EMPTY_INFO	/* flinfo indicates empty blocks */
 
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes */
 #endif
 
 #endif	/* __CONFIG_H */

include/lh7a400.h

@@ -1,75 +0,0 @@
-/*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * lh7a400 SoC interface
- */
-
-#ifndef __LH7A400_H__
-#define __LH7A400_H__
-
-#include "lh7a40x.h"
-
-/* Interrupt Controller (userguide 8.2.1) */
-typedef struct {
-	volatile u32  intsr;
-	volatile u32  intrsr;
-	volatile u32  intens;
-	volatile u32  intenc;
-	volatile u32  rsvd1;
-	volatile u32  rsvd2;
-	volatile u32  rsvd3;
-} /*__attribute__((__packed__))*/ lh7a400_interrupt_t;
-#define LH7A400_INTERRUPT_BASE    (0x80000500)
-#define LH7A400_INTERRUPT_PTR     ((lh7a400_interrupt_t*) LH7A400_INTERRUPT_BASE)
-
-/* (DMA) Direct Memory Access Controller (userguide 9.2.1) */
-typedef struct {
-	lh7a40x_dmachan_t  chan[15];
-	volatile u32       glblint;
-	volatile u32       rsvd1;
-	volatile u32       rsvd2;
-	volatile u32       rsvd3;
-} /*__attribute__((__packed__))*/ lh7a400_dma_t;
-
-#define LH7A400_DMA_BASE      (0x80002800)
-#define DMA_USBTX_OFFSET      (0x000)
-#define DMA_USBRX_OFFSET      (0x040)
-#define DMA_MMCTX_OFFSET      (0x080)
-#define DMA_MMCRX_OFFSET      (0x0C0)
-#define DMA_AC97_BASE         (0x80002A00)
-
-#define LH7A400_DMA_PTR    ((lh7a400_dma_t*) LH7A400_DMA_BASE)
-#define LH7A400_DMA_USBTX \
-	((lh7a400_dmachan_t*) (LH7A400_DMA_BASE + DMA_USBTX_OFFSET))
-#define LH7A400_DMA_USBRX \
-	((lh7a400_dmachan_t*) (LH7A400_DMA_BASE + DMA_USBRX_OFFSET))
-#define LH7A400_DMA_MMCTX \
-	((lh7a400_dmachan_t*) (LH7A400_DMA_BASE + DMA_MMCTX_OFFSET))
-#define LH7A400_DMA_MMCRX \
-	((lh7a400_dmachan_t*) (LH7A400_DMA_BASE + DMA_MMCRX_OFFSET))
-#define LH7A400_AC97RX(n) \
-	((lh7a400_dmachan_t*) (LH7A400_AC97_BASE + \
-	((2*n) * sizeof(lh7a400_dmachan_t))))
-#define LH7A400_AC97TX(n) \
-	((lh7a400_dmachan_t*) (LH7A400_AC97_BASE + \
-	(((2*n)+1) * sizeof(lh7a400_dmachan_t))))
-
-#endif  /* __LH7A400_H__ */

include/lh7a404.h

@@ -1,83 +0,0 @@
-/*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * lh7a404 SoC interface
- */
-
-#ifndef __LH7A404_H__
-#define __LH7A404_H__
-
-#include "lh7a40x.h"
-
-/* Interrupt Controller (userguide 8.2.1) */
-typedef struct {
-	volatile u32  irqstatus;
-	volatile u32  fiqstatus;
-	volatile u32  rawintr;
-	volatile u32  intsel;
-	volatile u32  inten;
-	volatile u32  intenclr;
-	volatile u32  softint;
-	volatile u32  softintclr;
-	volatile u32  protect;
-	volatile u32  unused1;
-	volatile u32  unused2;
-	volatile u32  vectaddr;
-	volatile u32  nvaddr;
-	volatile u32  unused3[32];
-	volatile u32  vad[16];
-	volatile u32  unused4[44];
-	volatile u32  vectcntl[16];
-	volatile u32  unused5[44];
-	volatile u32  itcr;
-	volatile u32  itip1;
-	volatile u32  itip2;
-	volatile u32  itop1;
-	volatile u32  itop2;
-	volatile u32  unused6[333];
-	volatile u32  periphid[4];
-	volatile u32  pcellid[4];
-} /*__attribute__((__packed__))*/ lh7a404_vic_t;
-#define LH7A404_VIC_BASE	(0x80008000)
-#define LH7A400_VIC_PTR(x)  ((lh7a404_vic_t*)(LH7A400_VIC_BASE + (x*0x2000)))
-
-
-typedef struct {
-	lh7a40x_dmachan_t  m2p0_tx;
-	lh7a40x_dmachan_t  m2p1_rx;
-	lh7a40x_dmachan_t  m2p2_tx;
-	lh7a40x_dmachan_t  m2p3_rx;
-	lh7a40x_dmachan_t  m2m0;
-	lh7a40x_dmachan_t  m2m1;
-	lh7a40x_dmachan_t  unused1;
-	lh7a40x_dmachan_t  unused2;
-	lh7a40x_dmachan_t  m2p5_rx;
-	lh7a40x_dmachan_t  m2p4_tx;
-	lh7a40x_dmachan_t  m2p7_rx;
-	lh7a40x_dmachan_t  m2p6_tx;
-	lh7a40x_dmachan_t  m2p9_rx;
-	lh7a40x_dmachan_t  m2p8_tx;
-	volatile u32       chanarb;
-	volatile u32       glblint;
-} /*__attribute__((__packed__))*/ lh7a400_dma_t;
-
-
-#endif  /* __LH7A404_H__ */

include/lh7a40x.h

@@ -1,279 +0,0 @@
-/*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * lh7a40x SoC series common interface
- */
-
-#ifndef __LH7A40X_H__
-#define __LH7A40X_H__
-
-/* (SMC) Static Memory Controller (usersguide 4.2.1) */
-typedef struct {
-	volatile u32  attib;
-	volatile u32  com;
-	volatile u32  io;
-	volatile u32  rsvd1;
-} /*__attribute__((__packed__))*/ lh7a40x_pccard_t;
-
-typedef struct {
-	volatile u32      bcr[8];
-	lh7a40x_pccard_t  pccard[2];
-	volatile u32	  pcmciacon;
-} /*__attribute__((__packed__))*/ lh7a40x_smc_t;
-#define LH7A40X_SMC_BASE  (0x80002000)
-#define LH7A40X_SMC_PTR   ((lh7a40x_smc_t*) LH7A40X_SMC_BASE)
-
-/* (SDMC) Synchronous Dynamic Ram Controller (usersguide 5.3.1) */
-typedef struct {
-	volatile u32  rsvd1;
-	volatile u32  gblcnfg;
-	volatile u32  rfshtmr;
-	volatile u32  bootstat;
-	volatile u32  sdcsc[4];
-} /*__attribute__((__packed__))*/ lh7a40x_sdmc_t;
-#define LH7A40X_SDMC_BASE  (0x80002400)
-#define LH7A40X_SDMC_PTR   ((lh7a40x_sdmc_t*) LH7A40X_SDMC_BASE)
-
-/* (CSC) Clock and State Controller (userguide 6.2.1) */
-typedef struct {
-	volatile u32  pwrsr;
-	volatile u32  pwrcnt;
-	volatile u32  halt;
-	volatile u32  stby;
-	volatile u32  bleoi;
-	volatile u32  mceoi;
-	volatile u32  teoi;
-	volatile u32  stfclr;
-	volatile u32  clkset;
-	volatile u32  scrreg[2];
-	volatile u32  rsvd1;
-	volatile u32  usbreset;
-} /*__attribute__((__packed__))*/ lh7a40x_csc_t;
-#define LH7A40X_STPWR_BASE  (0x80000400)
-#define LH7A40X_CSC_PTR     ((lh7a40x_csc_t*) LH7A40X_STPWR_BASE)
-
-#define CLKSET_SMCROM		(0x01000000)
-#define CLKSET_PS		(0x000C0000)
-#define CLKSET_PS_0		(0x00000000)
-#define CLKSET_PS_1		(0x00040000)
-#define CLKSET_PS_2		(0x00080000)
-#define CLKSET_PS_3		(0x000C0000)
-#define CLKSET_PCLKDIV		(0x00030000)
-#define CLKSET_PCLKDIV_2	(0x00000000)
-#define CLKSET_PCLKDIV_4	(0x00010000)
-#define CLKSET_PCLKDIV_8	(0x00020000)
-#define CLKSET_MAINDIV2		(0x0000f800)
-#define CLKSET_MAINDIV1		(0x00000780)
-#define CLKSET_PREDIV		(0x0000007C)
-#define CLKSET_HCLKDIV		(0x00000003)
-
-/* (DMA) Direct Memory Access Controller (userguide 9.2.1) */
-typedef struct {
-	volatile u32  maxcnt;
-	volatile u32  base;
-	volatile u32  current;
-	volatile u32  rsvd1;
-} lh7a40x_dmabuf_t;
-
-typedef struct {
-	volatile u32      control;
-	volatile u32      interrupt;
-	volatile u32      rsvd1;
-	volatile u32      status;
-	volatile u32      rsvd2;
-	volatile u32      remain;
-	volatile u32      rsvd3;
-	volatile u32      rsvd4;
-	lh7a40x_dmabuf_t  buf[2];
-} /*__attribute__((__packed__))*/ lh7a40x_dmachan_t;
-
-
-/* (WDT) Watchdog Timer (userguide 11.2.1) */
-typedef struct {
-	volatile u32  ctl;
-	volatile u32  rst;
-	volatile u32  status;
-	volatile u32  count[4];
-} /*__attribute__((__packed__))*/ lh7a40x_wdt_t;
-#define LH7A40X_WDT_BASE    (0x80001400)
-#define LH7A40X_WDT_PTR     ((lh7a40x_wdt_t*) LH7A40X_WDT_BASE)
-
-/* (RTC) Real Time Clock (lh7a400 userguide 12.2.1, lh7a404 userguide 13.2.1) */
-typedef struct {
-	volatile u32  rtcdr;
-	volatile u32  rtclr;
-	volatile u32  rtcmr;
-	volatile u32  unk1;
-	volatile u32  rtcstat_eoi;
-	volatile u32  rtccr;
-	volatile u32  rsvd1[58];
-} /*__attribute__((__packed__))*/ lh7a40x_rtc_t;
-#define LH7A40X_RTC_BASE    (0x80000D00)
-#define LH7A40X_RTC_PTR     ((lh7a40x_rtc_t*) LH7A40X_RTC_BASE)
-
-/* Timers (lh7a400 userguide 13.2.1, lh7a404 userguide 11.2.1) */
-typedef struct {
-	volatile u32  load;
-	volatile u32  value;
-	volatile u32  control;
-	volatile u32  tceoi;
-} /*__attribute__((__packed__))*/ lh7a40x_timer_t;
-
-typedef struct {
-	lh7a40x_timer_t  timer1;
-	volatile u32     rsvd1[4];
-	lh7a40x_timer_t  timer2;
-	volatile u32     unk1[4];
-	volatile u32     bzcon;
-	volatile u32     unk2[15];
-	lh7a40x_timer_t  timer3;
-	/*volatile u32     rsvd2;*/
-} /*__attribute__((__packed__))*/ lh7a40x_timers_t;
-#define LH7A40X_TIMERS_BASE    (0x80000C00)
-#define LH7A40X_TIMERS_PTR     ((lh7a40x_timers_t*) LH7A40X_TIMERS_BASE)
-
-#define TIMER_EN	(0x00000080)
-#define TIMER_PER	(0x00000040)
-#define TIMER_FREE	(0x00000000)
-#define TIMER_CLK508K	(0x00000008)
-#define TIMER_CLK2K	(0x00000000)
-
-/* (SSP) Sychronous Serial Ports (lh7a400 userguide 14.2.1, lh7a404 userguide 14.2.1) */
-typedef struct {
-	volatile u32  cr0;
-	volatile u32  cr1;
-	volatile u32  irr_roeoi;
-	volatile u32  dr;
-	volatile u32  cpr;
-	volatile u32  sr;
-	/*volatile u32  rsvd1[58];*/
-} /*__attribute__((__packed__))*/ lh7a40x_ssp_t;
-#define LH7A40X_SSP_BASE    (0x80000B00)
-#define LH7A40X_SSP_PTR     ((lh7a40x_ssp_t*) LH7A40X_SSP_BASE)
-
-/* (UART) Universal Asychronous Receiver/Transmitter (lh7a400 userguide 15.2.1, lh7a404 userguide 15.2.1) */
-typedef struct {
-	volatile u32  data;
-	volatile u32  fcon;
-	volatile u32  brcon;
-	volatile u32  con;
-	volatile u32  status;
-	volatile u32  rawisr;
-	volatile u32  inten;
-	volatile u32  isr;
-	volatile u32  rsvd1[56];
-} /*__attribute__((__packed__))*/ lh7a40x_uart_t;
-#define LH7A40X_UART_BASE    (0x80000600)
-#define LH7A40X_UART_PTR(n) \
-	((lh7a40x_uart_t*) (LH7A40X_UART_BASE + ((n-1) * sizeof(lh7a40x_uart_t))))
-
-#define UART_BE		(0x00000800)      /* the rx error bits */
-#define UART_OE		(0x00000400)
-#define UART_PE		(0x00000200)
-#define UART_FE		(0x00000100)
-
-#define UART_WLEN	(0x00000060)	/* fcon bits */
-#define UART_WLEN_8	(0x00000060)
-#define UART_WLEN_7	(0x00000040)
-#define UART_WLEN_6	(0x00000020)
-#define UART_WLEN_5	(0x00000000)
-#define UART_FEN	(0x00000010)
-#define UART_STP2	(0x00000008)
-#define UART_STP2_2	(0x00000008)
-#define UART_STP2_1	(0x00000000)
-#define UART_EPS	(0x00000004)
-#define UART_EPS_EVEN	(0x00000004)
-#define UART_EPS_ODD	(0x00000000)
-#define UART_PEN	(0x00000002)
-#define UART_BRK	(0x00000001)
-
-#define UART_BAUDDIV	(0x0000ffff)	/* brcon bits */
-
-#define UART_SIRBD	(0x00000080)	/* con bits */
-#define UART_LBE	(0x00000040)
-#define UART_MXP	(0x00000020)
-#define UART_TXP	(0x00000010)
-#define UART_RXP	(0x00000008)
-#define UART_SIRLP	(0x00000004)
-#define UART_SIRD	(0x00000002)
-#define UART_EN		(0x00000001)
-
-#define UART_TXFE	(0x00000080)	/* status bits */
-#define UART_RXFF	(0x00000040)
-#define UART_TXFF	(0x00000020)
-#define UART_RXFE	(0x00000010)
-#define UART_BUSY	(0x00000008)
-#define UART_DCD	(0x00000004)
-#define UART_DSR	(0x00000002)
-#define UART_CTS	(0x00000001)
-
-#define UART_MSEOI	(0xfffffff0)	/* rawisr interrupt bits */
-
-#define UART_RTI	(0x00000008)	/* generic interrupt bits */
-#define UART_MI		(0x00000004)
-#define UART_TI		(0x00000002)
-#define UART_RI		(0x00000001)
-
-/* (GPIO) General Purpose IO and External Interrupts (userguide 16.2.1) */
-typedef struct {
-	volatile u32  pad;
-	volatile u32  pbd;
-	volatile u32  pcd;
-	volatile u32  pdd;
-	volatile u32  padd;
-	volatile u32  pbdd;
-	volatile u32  pcdd;
-	volatile u32  pddd;
-	volatile u32  ped;
-	volatile u32  pedd;
-	volatile u32  kbdctl;
-	volatile u32  pinmux;
-	volatile u32  pfd;
-	volatile u32  pfdd;
-	volatile u32  pgd;
-	volatile u32  pgdd;
-	volatile u32  phd;
-	volatile u32  phdd;
-	volatile u32  rsvd1;
-	volatile u32  inttype1;
-	volatile u32  inttype2;
-	volatile u32  gpiofeoi;
-	volatile u32  gpiointen;
-	volatile u32  intstatus;
-	volatile u32  rawintstatus;
-	volatile u32  gpiodb;
-	volatile u32  papd;
-	volatile u32  pbpd;
-	volatile u32  pcpd;
-	volatile u32  pdpd;
-	volatile u32  pepd;
-	volatile u32  pfpd;
-	volatile u32  pgpd;
-	volatile u32  phpd;
-} /*__attribute__((__packed__))*/ lh7a40x_gpioint_t;
-#define LH7A40X_GPIOINT_BASE    (0x80000E00)
-#define LH7A40X_GPIOINT_PTR     ((lh7a40x_gpioint_t*) LH7A40X_GPIOINT_BASE)
-
-/* Embedded SRAM */
-#define CONFIG_SYS_SRAM_BASE	(0xB0000000)
-#define CONFIG_SYS_SRAM_SIZE	(80*1024)	/* 80kB */
-
-#endif  /* __LH7A40X_H__ */

include/lpd7a400_cpld.h

@@ -1,195 +0,0 @@
-/*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * Logic lh7a400-10 Card Engine CPLD interface
- */
-
-#ifndef __LPD7A400_CPLD_H_
-#define __LPD7A400_CPLD_H_
-
-
-/*
- * IO Controller Address and Register Definitions
- *   - using LH7A400-10 Card Engine IO Controller Specification
- *     (logic PN: 70000079)
- */
-
-/*------------------------------------------------------------------
- * Slow Peripherals (nCS6)
- */
-#define LPD7A400_CPLD_CF		(0x60200000)
-#define LPD7A400_CPLD_ISA		(0x60400000)
-
-/*------------------------------------------------------------------
- * Fast Peripherals (nCS7)
- *
- * The CPLD directs access to 0x70000000-0x701fffff to the onboard
- * ethernet controller
- */
-#define LPD7A400_CPLD_WLAN_BASE		(0x70000000)
-
-/* All registers are 8 bit */
-#define LPD7A400_CPLD_CECTL_REG		(0x70200000)
-#define LPD7A400_CPLD_SPIDATA_REG	(0x70600000)
-#define LPD7A400_CPLD_SPICTL_REG	(0x70800000)
-#define LPD7A400_CPLD_EEPSPI_REG	(0x70a00000)
-#define LPD7A400_CPLD_INTMASK_REG	(0x70c00000)
-#define LPD7A400_CPLD_MODE_REG		(0x70e00000)
-#define LPD7A400_CPLD_FLASH_REG		(0x71000000)
-#define LPD7A400_CPLD_PWRMG_REG		(0x71200000)
-#define LPD7A400_CPLD_REV_REG		(0x71400000)
-#define LPD7A400_CPLD_EXTGPIO_REG	(0x71600000)
-#define LPD7A400_CPLD_GPIODATA_REG	(0x71800000)
-#define LPD7A400_CPLD_GPIODIR_REG	(0x71a00000)
-
-#define LPD7A400_CPLD_REGPTR		(volatile u8*)
-
-/* Card Engine Control Register (section 3.1.2) */
-#define CECTL_SWINT	(0x80)	/* Software settable interrupt source
-				   (routed to uP PF3)
-				   0 = generate interrupt, 1 = do not */
-#define CECTL_OCMSK	(0x40)	/* USB1 connection interrupt mask
-				   0 = not masked, 1 = masked */
-#define CECTL_PDRV	(0x20)	/* PCC_nDRV output
-				   0 = active, 1 = inactive */
-#define CECTL_USB1C	(0x10)	/* USB1 connection interrupt
-				   0 = active, 1 = inactive */
-#define CECTL_USB1P	(0x08)  /* USB1 Power enable
-				   0 = enabled, 1 = disabled */
-#define CECTL_AWKP	(0x04)  /* Auto-Wakeup enable
-				   0 = enabled, 1 = disabled */
-#define CECTL_LCDV	(0x02)  /* LCD VEE enable
-				   0 = disabled, 1 = enabled */
-#define CECTL_WLPE	(0x01)  /* Wired LAN power enable
-				   0 = enabled, 1 = disabled */
-
-/* SPI Control Register (section 3.1.5) */
-#define SPICTL_SPLD	(0x20)	/* SPI load (R)
-				   0 = data reg. has not been loaded, shift
-				       count has not been reset
-				   1 = data reg. loaded, shift count reset */
-#define SPICTL_SPST	(0x10)  /* SPI start (RW)
-				   0 = don't load data reg. and reset shift count
-				   1 = ready to load data reg and reset shift count */
-#define SPICTL_SPDN	(0x08)  /* SPI done (R)
-				   0 = not done
-				   1 = access done */
-#define SPICTL_SPRW	(0x04)  /* SPI read/write (RW)
-				   0 = SPI write access
-				   1 = SPI read access */
-#define SPICTL_STCS	(0x02)  /* SPI touch chip select (RW)
-				   0 = not selected
-				   1 = selected */
-#define SPICTL_SCCS	(0x01)  /* SPI CODEC chip select (RW) {not used}
-				   0 = not selected
-				   1 = selected */
-
-/* EEPROM SPI Interface Register (section 3.1.6) */
-#define EEPSPI_EECS	(0x08)	/* EEPROM chip select (RW)
-				   0 = not selected
-				   1 = selected */
-#define EEPSPI_EECK	(0x04)	/* EEPROM SPI clock (RW) */
-#define EEPSPI_EETX	(0x02)  /* EEPROM SPI tx data (RW) */
-#define EEPSPI_EERX	(0x01)  /* EEPROM SPI rx data (R) */
-
-/* Interrupt/Mask Register (section 3.1.7) */
-#define INTMASK_CMSK	(0x80)  /* CPLD_nIRQD interrupt mask (RW)
-				   0 = not masked
-				   1 = masked */
-#define INTMASK_CIRQ	(0x40)	/* interrupt signal to CPLD (R)
-				   0 = interrupt active
-				   1 = no interrupt */
-#define INTMASK_PIRQ	(0x10)	/* legacy, no effect */
-#define INTMASK_TMSK	(0x08)	/* Touch chip interrupt mask (RW)
-				   0 = not masked
-				   1 = masked */
-#define INTMASK_WMSK	(0x04)  /* Wired LAN interrupt mask (RW)
-				   0 = not masked
-				   1 = masked */
-#define INTMASK_TIRQ	(0x02)  /* Touch chip interrupt request (R)
-				   0 = interrupt active
-				   1 = no interrupt */
-#define INTMASK_WIRQ	(0x01)  /* Wired LAN interrupt request (R)
-				   0 = interrupt active
-				   1 = no interrupt */
-
-/* Mode Register (section 3.1.8) */
-#define MODE_VS1	(0x80)  /* PCMCIA Voltage Sense 1 input (PCC_VS1) (R)
-				   0 = active slot VS1 pin is low
-				   1 = active slot VS1 pin is high */
-#define MODE_CD2	(0x40)  /* PCMCIA Card Detect 2 input (PCC_nCD2) (R)
-				   0 = active slot CD2 is low
-				   1 = active slot CD2 is high */
-#define MODE_IOIS16	(0x20)  /* PCMCIA IOIS16 input (PCC_nIOIS16) (R)
-				   0 = 16 bit access area
-				   1 = 8 bit access area */
-#define MODE_CD1	(0x10)  /* PCMCIA Card Detect 1 input (PCC_nCD1) (R)
-				   0 = active slot CD1 is low
-				   1 = active slot CD1 is high */
-#define MODE_upMODE3	(0x08)  /* Mode Pin 3 (R)
-				   0 = off-board boot device
-				   1 = on-board boot device (flash) */
-#define MODE_upMODE2	(0x04)  /* Mode Pin 2 (R) (LH7A400 Little Endian only)
-				   0 = big endian
-				   1 = little endian */
-#define MODE_upMODE1	(0x02)  /* Mode Pin 1 and Mode Pin 2 (R) */
-#define MODE_upMODE0	(0x01)  /*   - bus width at boot */
-
-
-/* Flash Register (section 3.1.9) */
-#define FLASH_FPOP	(0x08)	/* Flash populated (RW)
-				   0 = populated, 1 = not */
-#define FLASH_FST2	(0x04)  /* Flash status (R) (RY/BY# pin for upper 16 bit chip
-				   0 = busy, 1 = ready */
-#define FLASH_FST1	(0x02)  /* Flash status (R) (RY/BY# pin for lower 16 bit chip
-				   0 = busy, 1 = ready */
-#define FLASH_FPEN	(0x01)  /* Flash program enable (RW)
-				   0 = flash write protected
-				   1 = programming enabled */
-
-/* Power Management Register (section 3.1.10)
- *    - when either of these is low an unmaskable interrupt to cpu
- *      is generated
- */
-#define PWRMG_STBY	(0x10)  /* state of nSTANDBY signal to CPLD (R)
-				   0 = low, 1 = high */
-#define PWRMG_SPND	(0x04)  /* state of nSUSPEND signal to CPLD (R)
-				   0 = low, 1 = high */
-
-
-/* Extended GPIO Register (section 3.1.12) */
-#define EXTGPIO_STATUS1	(0x04)  /* Status 1 output (RW) (uP_STATUS_1)
-				   0 = set pin low, 1 = set pin high */
-#define EXTGPIO_STATUS2 (0x02)  /* Status 2 output (RW) (uP_STATUS_2)
-				   0 = set pin low, 1 = set pin high */
-#define EXTGPIO_GPIO1	(0x01)  /* General purpose output (RW) (CPLD_GPIO_1)
-				   0 = set pin low, 1 = set pin high */
-
-/* GPIO Data Register (section 3.1.13) */
-#define GPIODATA_GPIO2	(0x01)  /* General purpose input/output (RW) (CPLD_GPIO_2)
-				   0 = set low (output) / read low (input)
-				   1 = set high (output) / read high (input) */
-
-/* GPIO Direction Register (section 3.1.14) */
-#define GPIODIR_GPDR0	(0x01)  /* GPIO2 direction (RW)
-				   0 = output, 1 = input */
-
-#endif  /* __LH7A400_H__ */