ARM: remove duplicated code for LaCie boards

This patch groups together all the common functions for LaCie boards:
Ethernet PHY and MAC address initializations.

Moreover the configurations for LaCie Kirkwood boards are merged into
a single file: include/configs/lacie_kw.h

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>

board/LaCie/common/common.c

@@ -0,0 +1,87 @@
+/*
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <miiphy.h>
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+
+#define MV88E1116_LED_FCTRL_REG		10
+#define MV88E1116_CPRSP_CR3_REG		21
+#define MV88E1116_MAC_CTRL_REG		21
+#define MV88E1116_PGADR_REG		22
+#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
+
+void mv_phy_88e1116_init(const char *name)
+{
+	u16 reg;
+	u16 devadr;
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+		printf("Err..(%s) could not read PHY dev address\n", __func__);
+		return;
+	}
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
+	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, devadr);
+
+	printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_CMD_NET && CONFIG_RESET_PHY_R */
+
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
+int lacie_read_mac_address(uchar *mac_addr)
+{
+	int ret;
+	ushort version;
+
+	/* I2C-0 for on-board EEPROM */
+	i2c_set_bus_num(0);
+
+	/* Check layout version for EEPROM data */
+	ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
+			CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
+			(uchar *) &version, 2);
+	if (ret != 0) {
+		printf("Error: failed to read I2C EEPROM @%02x\n",
+			CONFIG_SYS_I2C_EEPROM_ADDR);
+		return ret;
+	}
+	version = be16_to_cpu(version);
+	if (version < 1 || version > 3) {
+		printf("Error: unknown version %d for EEPROM data\n",
+			version);
+		return -1;
+	}
+
+	/* Read Ethernet MAC address from EEPROM */
+	ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
+			CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac_addr, 6);
+	if (ret != 0)
+		printf("Error: failed to read I2C EEPROM @%02x\n",
+			CONFIG_SYS_I2C_EEPROM_ADDR);
+	return ret;
+}
+#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_EEPROM_ADDR */

board/LaCie/common/common.h

@@ -0,0 +1,20 @@
+/*
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef _LACIE_COMMON_H
+#define _LACIE_COMMON_H
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+void mv_phy_88e1116_init(const char *name);
+#endif
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
+int lacie_read_mac_address(uchar *mac);
+#endif
+
+#endif /* _LACIE_COMMON_H */

board/LaCie/edminiv2/Makefile

@@ -26,10 +26,13 @@
 #
 
 include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
 
 LIB	= $(obj)lib$(BOARD).o
 
-COBJS	:= edminiv2.o
+COBJS	:= edminiv2.o ../common/common.o
 
 SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))

board/LaCie/edminiv2/edminiv2.c

@@ -27,7 +27,6 @@
 #include <common.h>
 #include <miiphy.h>
 #include <asm/arch/orion5x.h>
-#include "edminiv2.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -96,33 +95,6 @@ int board_init(void)
 /* Configure and enable MV88E1116 PHY */
 void reset_phy(void)
 {
-	u16 reg;
-	u16 devadr;
-	char *name = "egiga0";
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	/* command to read PHY dev address */
-	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
-		printf("Err..%s could not read PHY dev address\n",
-			__func__);
-		return;
-	}
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	miiphy_reset(name, devadr);
-
-	printf("88E1116 Initialized on %s\n", name);
+	mv_phy_88e1116_init("egiga0");
 }
 #endif /* CONFIG_RESET_PHY_R */

board/LaCie/edminiv2/edminiv2.h

@@ -1,41 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.h:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-#ifndef __EDMINIV2_BASE_H
-#define __EDMINIV2_BASE_H
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG		10
-#define MV88E1116_CPRSP_CR3_REG		21
-#define MV88E1116_MAC_CTRL_REG		21
-#define MV88E1116_PGADR_REG		22
-#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
-
-#endif /* __EDMINIV2_BASE_H */

board/LaCie/net2big_v2/Makefile

@@ -21,10 +21,13 @@
 #
 
 include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
 
 LIB	= $(obj)lib$(BOARD).o
 
-COBJS	:= net2big_v2.o
+COBJS	:= $(BOARD).o ../common/common.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))

board/LaCie/net2big_v2/net2big_v2.c

@@ -21,15 +21,14 @@
  */
 
 #include <common.h>
-#include <miiphy.h>
-#include <netdev.h>
 #include <command.h>
-#include <i2c.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/kirkwood.h>
 #include <asm/arch/mpp.h>
 #include <asm/arch/gpio.h>
+
 #include "net2big_v2.h"
+#include "../common/common.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -92,91 +91,29 @@ int board_init(void)
 	return 0;
 }
 
+#if defined(CONFIG_MISC_INIT_R)
 int misc_init_r(void)
 {
-#ifdef CONFIG_CMD_I2C
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
 	if (!getenv("ethaddr")) {
-		ushort version;
 		uchar mac[6];
-		int ret;
-
-		/* I2C-0 for on-board EEPROM */
-		i2c_set_bus_num(0);
-
-		/* Check layout version for EEPROM data */
-		ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
-				CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
-				(uchar *) &version, 2);
-		if (ret != 0) {
-			printf("Error: failed to read I2C EEPROM @%02x\n",
-				CONFIG_SYS_I2C_EEPROM_ADDR);
-			return ret;
-		}
-		version = be16_to_cpu(version);
-		if (version < 1 || version > 3) {
-			printf("Error: unknown version %d for EEPROM data\n",
-				version);
-			return -1;
-		}
-
-		/* Read Ethernet MAC address from EEPROM */
-		ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
-				CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac, 6);
-		if (ret != 0) {
-			printf("Error: failed to read I2C EEPROM @%02x\n",
-				CONFIG_SYS_I2C_EEPROM_ADDR);
-			return ret;
-		}
-		eth_setenv_enetaddr("ethaddr", mac);
+		if (lacie_read_mac_address(mac) == 0)
+			eth_setenv_enetaddr("ethaddr", mac);
 	}
-#endif /* CONFIG_CMD_I2C */
-
+#endif
 	return 0;
 }
+#endif
 
-void mv_phy_88e1116_init(char *name)
-{
-	u16 reg;
-	u16 devadr;
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	/* command to read PHY dev address */
-	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
-		printf("Err..(%s) could not read PHY dev address\n", __func__);
-		return;
-	}
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	if (miiphy_read(name, devadr, MII_BMCR, &reg) != 0) {
-		printf("Err..(%s) PHY status read failed\n", __func__);
-		return;
-	}
-	if (miiphy_write(name, devadr, MII_BMCR, reg | 0x8000) != 0) {
-		printf("Err..(%s) PHY reset failed\n", __func__);
-		return;
-	}
-
-	debug("88E1116 Initialized on %s\n", name);
-}
-
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
 /* Configure and initialize PHY */
 void reset_phy(void)
 {
 	mv_phy_88e1116_init("egiga0");
 }
+#endif
 
+#if defined(CONFIG_KIRKWOOD_GPIO)
 /* Return GPIO push button status */
 static int
 do_read_push_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
@@ -186,3 +123,4 @@ do_read_push_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 
 U_BOOT_CMD(button, 1, 1, do_read_push_button,
 	   "Return GPIO push button status 0=off 1=on", "");
+#endif

board/LaCie/net2big_v2/net2big_v2.h

@@ -32,12 +32,4 @@
 /* Buttons */
 #define NET2BIG_V2_GPIO_PUSH_BUTTON	34
 
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG		10
-#define MV88E1116_CPRSP_CR3_REG		21
-#define MV88E1116_MAC_CTRL_REG		21
-#define MV88E1116_PGADR_REG		22
-#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
-
 #endif /* NET2BIG_V2_H */

board/LaCie/netspace_v2/Makefile

@@ -21,10 +21,13 @@
 #
 
 include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
 
 LIB	= $(obj)lib$(BOARD).o
 
-COBJS	:= netspace_v2.o
+COBJS	:= $(BOARD).o ../common/common.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))

board/LaCie/netspace_v2/netspace_v2.c

@@ -21,15 +21,14 @@
  */
 
 #include <common.h>
-#include <miiphy.h>
-#include <netdev.h>
 #include <command.h>
-#include <i2c.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/kirkwood.h>
 #include <asm/arch/mpp.h>
 #include <asm/arch/gpio.h>
+
 #include "netspace_v2.h"
+#include "../common/common.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -90,91 +89,29 @@ int board_init(void)
 	return 0;
 }
 
+#if defined(CONFIG_MISC_INIT_R)
 int misc_init_r(void)
 {
 #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
 	if (!getenv("ethaddr")) {
-		ushort version;
 		uchar mac[6];
-		int ret;
-
-		/* I2C-0 for on-board EEPROM */
-		i2c_set_bus_num(0);
-
-		/* Check layout version for EEPROM data */
-		ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
-				CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
-				(uchar *) &version, 2);
-		if (ret != 0) {
-			printf("Error: failed to read I2C EEPROM @%02x\n",
-				CONFIG_SYS_I2C_EEPROM_ADDR);
-			return ret;
-		}
-		version = be16_to_cpu(version);
-		if (version < 1 || version > 3) {
-			printf("Error: unknown version %d for EEPROM data\n",
-				version);
-			return -1;
-		}
-
-		/* Read Ethernet MAC address from EEPROM */
-		ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 2,
-				CONFIG_SYS_I2C_EEPROM_ADDR_LEN, mac, 6);
-		if (ret != 0) {
-			printf("Error: failed to read I2C EEPROM @%02x\n",
-				CONFIG_SYS_I2C_EEPROM_ADDR);
-			return ret;
-		}
-		eth_setenv_enetaddr("ethaddr", mac);
+		if (lacie_read_mac_address(mac) == 0)
+			eth_setenv_enetaddr("ethaddr", mac);
 	}
-#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_EEPROM_ADDR */
-
+#endif
 	return 0;
 }
+#endif
 
-void mv_phy_88e1116_init(char *name)
-{
-	u16 reg;
-	u16 devadr;
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	/* command to read PHY dev address */
-	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
-		printf("Err..(%s) could not read PHY dev address\n", __func__);
-		return;
-	}
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	if (miiphy_read(name, devadr, MII_BMCR, &reg) != 0) {
-		printf("Err..(%s) PHY status read failed\n", __func__);
-		return;
-	}
-	if (miiphy_write(name, devadr, MII_BMCR, reg | 0x8000) != 0) {
-		printf("Err..(%s) PHY reset failed\n", __func__);
-		return;
-	}
-
-	debug("88E1116 Initialized on %s\n", name);
-}
-
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
 /* Configure and initialize PHY */
 void reset_phy(void)
 {
 	mv_phy_88e1116_init("egiga0");
 }
+#endif
 
+#if defined(CONFIG_KIRKWOOD_GPIO)
 /* Return GPIO button status */
 static int
 do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
@@ -184,3 +121,4 @@ do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 
 U_BOOT_CMD(button, 1, 1, do_read_button,
 	   "Return GPIO button status 0=off 1=on", "");
+#endif

board/LaCie/netspace_v2/netspace_v2.h

@@ -31,12 +31,4 @@
 
 #define NETSPACE_V2_GPIO_BUTTON         32
 
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG		10
-#define MV88E1116_CPRSP_CR3_REG		21
-#define MV88E1116_MAC_CTRL_REG		21
-#define MV88E1116_PGADR_REG		22
-#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
-
 #endif /* NETSPACE_V2_H */

boards.cfg

@@ -140,10 +140,10 @@ km_kirkwood                  arm         arm926ejs   km_arm              keymile
 km_kirkwood_pci              arm         arm926ejs   km_arm              keymile        kirkwood	km_kirkwood:KM_RECONFIG_XLX
 mgcoge3un                    arm         arm926ejs   km_arm              keymile        kirkwood
 portl2                       arm         arm926ejs   km_arm              keymile        kirkwood
-inetspace_v2                 arm         arm926ejs   netspace_v2         LaCie          kirkwood    netspace_v2:INETSPACE_V2
-net2big_v2                   arm         arm926ejs   net2big_v2          LaCie          kirkwood
-netspace_v2                  arm         arm926ejs   netspace_v2         LaCie          kirkwood    netspace_v2:NETSPACE_V2
-netspace_max_v2              arm         arm926ejs   netspace_v2         LaCie          kirkwood    netspace_v2:NETSPACE_MAX_V2
+inetspace_v2                 arm         arm926ejs   netspace_v2         LaCie          kirkwood	lacie_kw:INETSPACE_V2
+net2big_v2                   arm         arm926ejs   net2big_v2          LaCie          kirkwood	lacie_kw:NET2BIG_V2
+netspace_v2                  arm         arm926ejs   netspace_v2         LaCie          kirkwood	lacie_kw:NETSPACE_V2
+netspace_max_v2              arm         arm926ejs   netspace_v2         LaCie          kirkwood	lacie_kw:NETSPACE_MAX_V2
 dreamplug                    arm         arm926ejs   -                   Marvell        kirkwood
 guruplug                     arm         arm926ejs   -                   Marvell        kirkwood
 mv88f6281gtw_ge              arm         arm926ejs   -                   Marvell        kirkwood

include/configs/netspace_v2.h → include/configs/lacie_kw.h

@@ -15,8 +15,8 @@
  * GNU General Public License for more details.
  */
 
-#ifndef _CONFIG_NETSPACE_V2_H
-#define _CONFIG_NETSPACE_V2_H
+#ifndef _CONFIG_LACIE_KW_H
+#define _CONFIG_LACIE_KW_H
 
 /*
  * Machine number definition
@@ -30,6 +30,9 @@
 #elif defined(CONFIG_NETSPACE_MAX_V2)
 #define CONFIG_MACH_TYPE		MACH_TYPE_NETSPACE_MAX_V2
 #define CONFIG_IDENT_STRING		" NS Max v2"
+#elif defined(CONFIG_NET2BIG_V2)
+#define CONFIG_MACH_TYPE		MACH_TYPE_NET2BIG_V2
+#define CONFIG_IDENT_STRING		" 2Big v2"
 #else
 #error "Unknown board"
 #endif
@@ -56,11 +59,19 @@
 #define CONFIG_CMD_USB
 
 /*
- * Core clock definition.
+ * Core clock definition
  */
 #define CONFIG_SYS_TCLK			166000000 /* 166MHz */
 
+/*
+ * SDRAM configuration
+ */
+#if defined(CONFIG_NET2BIG_V2)
+#define CONFIG_NR_DRAM_BANKS		2
+#else
 #define CONFIG_NR_DRAM_BANKS		1
+#endif
+
 #ifdef CONFIG_INETSPACE_V2
 /* Different SDRAM configuration and size for Internet Space v2 */
 #define CONFIG_SYS_KWD_CONFIG ($(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-is2.cfg)
@@ -81,7 +92,11 @@
 #define CONFIG_ENV_SPI_MAX_HZ           20000000 /* 20Mhz */
 #define CONFIG_SYS_IDE_MAXBUS           1
 #define CONFIG_SYS_IDE_MAXDEVICE        1
+#if defined(CONFIG_NET2BIG_V2)
+#define CONFIG_SYS_PROMPT		"2big2> "
+#else
 #define CONFIG_SYS_PROMPT		"ns2> "
+#endif
 
 /*
  * Ethernet Driver configuration
@@ -97,11 +112,10 @@
  */
 #ifdef CONFIG_MVSATA_IDE
 #define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
-/* Network Space Max v2 use 2 SATA ports */
-#ifdef CONFIG_NETSPACE_MAX_V2
+#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_NET2BIG_V2)
 #define CONFIG_SYS_ATA_IDE1_OFFSET      MV_SATA_PORT1_OFFSET
 #endif
-#endif
+#endif /* CONFIG_MVSATA_IDE */
 
 /*
  * Enable GPI0 support
@@ -176,4 +190,4 @@
 	"usbload=usb start && "					\
 		"fatload usb 0:1 $loadaddr /boot/$bootfile\0"
 
-#endif /* _CONFIG_NETSPACE_V2_H */
+#endif /* _CONFIG_LACIE_KW_H */

include/configs/net2big_v2.h

@@ -1,161 +0,0 @@
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef _CONFIG_NET2BIG_V2_H
-#define _CONFIG_NET2BIG_V2_H
-
-/*
- * Machine number information
- */
-#define CONFIG_IDENT_STRING		" 2Big v2"
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131		/* CPU Core subversion */
-#define CONFIG_KIRKWOOD			/* SOC Family Name */
-#define CONFIG_KW88F6281		/* SOC Name */
-#define CONFIG_MACH_NET2BIG_V2		/* Machine type */
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_USB
-
-/*
- * Core clock definition.
- */
-#define CONFIG_SYS_TCLK			166000000 /* 166MHz */
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#define CONFIG_NR_DRAM_BANKS		2
-#include "mv-common.h"
-
-/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_RBTREE
-#undef CONFIG_ENV_SPI_MAX_HZ
-#undef CONFIG_SYS_IDE_MAXBUS
-#undef CONFIG_SYS_IDE_MAXDEVICE
-#undef CONFIG_SYS_PROMPT
-#define CONFIG_ENV_SPI_MAX_HZ           20000000 /* 20Mhz */
-#define CONFIG_SYS_IDE_MAXBUS           1
-#define CONFIG_SYS_IDE_MAXDEVICE        1
-#define CONFIG_SYS_PROMPT		"2big2> "
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MISC_INIT_R /* Call misc_init_r() to initialize MAC address */
-#define CONFIG_MVGBE_PORTS		{1, 0} /* enable port 0 only */
-#define CONFIG_NETCONSOLE
-#endif
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
-#define CONFIG_SYS_ATA_IDE1_OFFSET      MV_SATA_PORT1_OFFSET
-#endif
-
-/*
- * Enable GPI0 support
- */
-#define CONFIG_KIRKWOOD_GPIO
-
-/*
- * Enable I2C support
- */
-#ifdef CONFIG_CMD_I2C
-/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
-#define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4 /* 16-byte page size */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1 /* 8-bit device address */
-#endif /* CONFIG_CMD_I2C */
-
-/*
- * File systems support
- */
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-
-/*
- * Use the HUSH parser
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-
-/*
- * Console configuration
- */
-#define CONFIG_CONSOLE_MUX
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-/*
- * Enable device tree support
- */
-#define CONFIG_OF_LIBFDT
-
-/*
- * Environment variables configurations
- */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SECT_SIZE		0x10000	/* 64KB */
-#define CONFIG_ENV_SIZE			0x1000	/* 4KB */
-#define CONFIG_ENV_ADDR			0x70000
-#define CONFIG_ENV_OFFSET		0x70000	/* env starts here */
-
-/*
- * Default environment variables
- */
-#define CONFIG_BOOTARGS "console=ttyS0,115200"
-
-#define CONFIG_BOOTCOMMAND					\
-	"dhcp && run netconsole; "				\
-	"if run usbload || run diskload; then bootm; fi"
-
-#define CONFIG_EXTRA_ENV_SETTINGS				\
-	"stdin=serial\0"					\
-	"stdout=serial\0"					\
-	"stderr=serial\0"					\
-	"bootfile=uImage\0"					\
-	"loadaddr=0x800000\0"					\
-	"autoload=no\0"						\
-	"netconsole="						\
-		"set stdin $stdin,nc; "				\
-		"set stdout $stdout,nc; "			\
-		"set stderr $stderr,nc;\0"			\
-	"diskload=ide reset && "				\
-		"ext2load ide 0:1 $loadaddr /boot/$bootfile\0"	\
-	"usbload=usb start && "					\
-		"fatload usb 0:1 $loadaddr /boot/$bootfile\0"
-
-#endif /* _CONFIG_NET2BIG_V2_H */