include/configs: Use new CONFIG_CMD_* in various g* named board config files.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

include/configs/evb4510.h

@@ -83,7 +83,6 @@
 #define CONFIG_CMD_PING
 
 
-
 #define CONFIG_ETHADDR		00:40:95:36:35:33
 #define CONFIG_NETMASK		255.255.255.0
 #define CONFIG_IPADDR		10.0.0.11

include/configs/gcplus.h

@@ -79,18 +79,23 @@
 
 #define CONFIG_BAUDRATE		38400
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | CFG_CMD_DHCP)
-#define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
+#define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
 
 #define CONFIG_BOOTDELAY	3
 #define CONFIG_BOOTARGS		"console=ttySA0,38400n8 mtdparts=sa1100-flash:1m@0(zImage),3m@1m(ramdisk.gz),12m@4m(userfs) root=/dev/nfs ip=bootp"
 #define CONFIG_BOOTCOMMAND	"bootp;tftp;bootm"
 #define CFG_AUTOLOAD            "n"             /* No autoload */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	38400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
 #endif

include/configs/gth2.h

@@ -71,12 +71,28 @@
 /* Boot from Compact flash partition 2 as default */
 #define CONFIG_BOOTCOMMAND	"ide reset;disk 0x81000000 0:2;run addmisc;bootm"
 
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP ) & \
- ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \
-   CFG_CMD_MII | CFG_CMD_LOADS	| CFG_CMD_LOADB | CFG_CMD_ELF | \
-   CFG_CMD_BDI | CFG_CMD_BEDBUG | CFG_CMD_NFS | CFG_CMD_AUTOSCRIPT ))
 
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_DHCP
+
+#undef CONFIG_CMD_ENV
+#undef CONFIG_CMD_FAT
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_MII
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_ELF
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_BEDBUG
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_AUTOSCRIPT
+
 
 /*
  * Miscellaneous configurable options

include/configs/gw8260.h

@@ -300,14 +300,21 @@
 /* Monitor Command Prompt */
 #define CFG_PROMPT      "=> "
 
-/* What U-Boot subsytems do you want enabled? */
-#define CONFIG_COMMANDS     (((CONFIG_CMD_DFL & ~(CFG_CMD_KGDB))) | \
-			       CFG_CMD_BEDBUG  | \
-			       CFG_CMD_ELF | \
-			       CFG_CMD_ASKENV  | \
-			       CFG_CMD_REGINFO | \
-			       CFG_CMD_IMMAP   | \
-			       CFG_CMD_MII)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_MII
+
+#undef CONFIG_CMD_KGDB
+
 
 /* Where do the internal registers live? */
 #define CFG_IMMR        0xf0000000
@@ -331,13 +338,10 @@
 #define CONFIG_GW8260       1   /* on an GW8260 Board  */
 #define CONFIG_CPM2		1	/* Has a CPM2 */
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 /*
  * Miscellaneous configurable options
  */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #  define CFG_CBSIZE        1024    /* Console I/O Buffer Size       */
 #else
 #  define CFG_CBSIZE        256     /* Console I/O Buffer Size       */
@@ -473,7 +477,7 @@
  */
 #define CFG_CACHELINE_SIZE  32      /* For MPC8260 CPU */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 # define CFG_CACHELINE_SHIFT    5   /* log base 2 of the above value */
 #endif