ppc4xx: Unify AMCC's board config files (part 3/3)

This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:

include/configs/amcc-common.h

This header now includes all common configuration options/defines which
are removed from the board specific headers.

The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.

Signed-off-by: Stefan Roese <sr@denx.de>

board/amcc/sequoia/config.mk

@@ -28,6 +28,10 @@ sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
 
 ifndef TEXT_BASE
 TEXT_BASE = 0xFFFA0000
+#
+# When defining CONFIG_VIDEO, TEXT_BASE needs to be 0xFFF80000
+# TEXT_BASE = 0xFFF80000
+#
 endif
 
 PLATFORM_CPPFLAGS += -DCONFIG_440=1

include/configs/ocotea.h

@@ -46,13 +46,17 @@
 #define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		ocotea
+#include "amcc-common.h"
+
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE	    0x00000000	    /* _must_ be 0		*/
 #define CFG_FLASH_BASE	    0xff800000	    /* start of FLASH		*/
-#define CFG_MONITOR_BASE    0xfffc0000	    /* start of monitor		*/
 #define CFG_PCI_MEMBASE	    0x80000000	    /* mapped pci memory	*/
 #define CFG_PERIPHERAL_BASE 0xe0000000	    /* internal peripherals	*/
 #define CFG_ISRAM_BASE	    0xc0000000	    /* internal SRAM		*/
@@ -74,18 +78,11 @@
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
-#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
-
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE		115200
-
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
 /*-----------------------------------------------------------------------
  * Environment
@@ -155,10 +152,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -167,54 +161,17 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=ocotea\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/ocotea/uImage\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fff00000\0"					\
 	"ramdisk_addr=fff10000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 #define CONFIG_PHY1_ADDR	2
 #define CONFIG_PHY2_ADDR	0x10
@@ -227,73 +184,15 @@
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
 #define CONFIG_PHY_RESET_DELAY	1000
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -310,28 +209,4 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */

include/configs/sequoia.h

@@ -34,11 +34,19 @@
 /* This config file is used for Sequoia (440EPx) and Rainier (440GRx)	*/
 #ifndef CONFIG_RAINIER
 #define CONFIG_440EPX		1	/* Specific PPC440EPx		*/
+#define CONFIG_HOSTNAME		sequoia
 #else
 #define CONFIG_440GRX		1	/* Specific PPC440GRx		*/
+#define CONFIG_HOSTNAME		rainier
 #endif
 #define CONFIG_440		1	/* ... PPC440 family		*/
 #define CONFIG_4xx		1	/* ... PPC4xx family		*/
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
 /* Detect Sequoia PLL input clock automatically via CPLD bit		*/
 #define CONFIG_SYS_CLK_FREQ    ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
 				33333333 : 33000000)
@@ -64,19 +72,9 @@
  * Base addresses -- Note these are effective addresses where the actual
  * resources get mapped (not physical addresses).
  */
-#ifndef CONFIG_VIDEO
-#define CFG_MONITOR_LEN		(384 * 1024) /* Reserve 384 kiB for Monitor  */
-#define CFG_MALLOC_LEN		(256 * 1024) /* Reserve 256 kiB for malloc() */
-#else
-#define CFG_MONITOR_LEN		(512 * 1024)    /* Reserve 512 kB for Monitor   */
-#define CFG_MALLOC_LEN		(1024 * 1024)   /* Reserve 1024 kB for malloc() */
-#endif
-
 #define CFG_TLB_FOR_BOOT_FLASH	0x0003
 #define CFG_BOOT_BASE_ADDR	0xf0000000
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
-#define CFG_MONITOR_BASE	TEXT_BASE
 #define CFG_NAND_ADDR		0xd0000000	/* NAND Flash		*/
 #define CFG_OCM_BASE		0xe0010000	/* ocm			*/
 #define CFG_OCM_DATA_ADDR	CFG_OCM_BASE
@@ -108,14 +106,9 @@
  * Serial Port
  */
 #define CFG_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI	1
 /* define this if you want console on UART1 */
 #undef CONFIG_UART1_CONSOLE
 
-#define CFG_BAUDRATE_TABLE						\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*
  * Environment
  */
@@ -227,10 +220,7 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -247,80 +237,27 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-#define CONFIG_PREBOOT	"echo;"						\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_RAINIER
-#define CONFIG_HOSTNAME		sequoia
-#define CFG_BOOTFILE		"bootfile=sequoia/uImage\0"
-#define CFG_DTBFILE		"fdt_file=sequoia/sequoia.dtb\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME		rainier
-#define CFG_BOOTFILE		"bootfile=rainier/uImage\0"
-#define CFG_DTBFILE		"fdt_file=rainier/rainier.dtb\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CFG_BOOTFILE							\
-	CFG_ROOTPATH							\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"addmisc=setenv bootargs ${bootargs}\0"				\
-	"flash_nfs=run nfsargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};"				\
-		"run nfsargs addip addtty addmisc;"			\
-		"bootm\0"						\
-	"fdt_file=sequoia/sequoia.dtb\0"				\
-	"fdt_addr=400000\0"						\
-	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
-		"tftp ${fdt_addr} ${fdt_file};"				\
-		"run nfsargs addip addtty addmisc;"			\
-		"bootm 200000 - ${fdt_addr}\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=FC000000\0"					\
 	"ramdisk_addr=FC180000\0"					\
-	"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0"		\
-	"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;"	\
-		"cp.b 200000 FFFA0000 60000\0"			        \
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_M88E1111_PHY	1
 #define	CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
 
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 
 #define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx	*/
-					/*   buffers & descriptors	*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #define CONFIG_PHY1_ADDR	1
 
@@ -347,35 +284,12 @@
 #define CONFIG_ISO_PARTITION
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
 #ifdef CONFIG_440EPX
@@ -406,35 +320,6 @@
 
 #define CONFIG_SUPPORT_VFAT
 
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-					/* Print Buffer Size		*/
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1  /* To use extended board_into (bd_t)	*/
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW		1	/* enable loopw command		*/
-#define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands	*/
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable	*/
-
 /*
  * PCI stuff
  */
@@ -452,13 +337,6 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC				*/
 #define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever			*/
 
-/*
- * For booting Linux, the board info and command line data have to be in the
- * first 8 MB of memory, since this is the maximum mapped by the Linux kernel
- * during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
 /*
  * External Bus Controller (EBC) Setup
  */
@@ -577,23 +455,6 @@
 }											\
 }
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02	/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400 /* speed to run kgdb serial port	*/
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #ifdef CONFIG_VIDEO
 #define CONFIG_BIOSEMU			/* x86 bios emulator for vga bios */
 #define CONFIG_ATI_RADEON_FB		/* use radeon framebuffer driver */

include/configs/taihu.h

@@ -32,6 +32,12 @@
 #define CONFIG_4xx		1	/*  member of PPC4xx family */
 #define CONFIG_TAIHU	        1	/*  on a taihu board */
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		taihu
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f */
 
 #define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
@@ -70,87 +76,31 @@
 
 #define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars */
 
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"bootfile=/tftpboot/taihu/uImage\0"				\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"netdev=eth0\0"							\
-	"hostname=taihu\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
+/*
+ * Default environment variables
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=FC000000\0"					\
 	"ramdisk_addr=FC180000\0"					\
-	"load=tftp 200000 /tftpboot/taihu/u-boot.bin\0"			\
-	"update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;"	\
-		"cp.b 200000 FFFC0000 40000\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0x14	/* PHY address			*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_PHY1_ADDR	0x10	/* EMAC1 PHY address		*/
-#define CONFIG_NET_MULTI	1
-#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
 #define CONFIG_PHY_RESET	1
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SPI
 
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
 #undef CONFIG_SPD_EEPROM		/* use SPD EEPROM for setup */
 #define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */
 #define CFG_SDRAM_BANKS	        2
@@ -168,23 +118,6 @@
 #define CFG_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
 #define CFG_SDRAM_tRFC		66	/* Auto refresh period */
 
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START  0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END	   0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
 /*
  * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
@@ -198,35 +131,13 @@
 #undef  CFG_EXT_SERIAL_CLOCK           /* external serial clock */
 #undef  CFG_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
 #define CFG_BASE_BAUD		691200
-
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_UART1_CONSOLE	1
 
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR	    0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
 /*-----------------------------------------------------------------------
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef  CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_NOPROBES	{ 0x69 } /* avoid iprobe hangup (why?) */
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6 /* 24C02 requires 5ms delay */
@@ -278,25 +189,12 @@ unsigned char spi_read(void);
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xFFE00000
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
 #define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
@@ -421,21 +319,5 @@ unsigned char spi_read(void);
 
 #define CPLD_REG0_ADDR	0x50100000
 #define CPLD_REG1_ADDR	0x50100001
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
 
 #endif	/* __CONFIG_H */

include/configs/taishan.h

@@ -34,6 +34,13 @@
 #define CONFIG_4xx		1	/* ... PPC4xx family		*/
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		taishan
+#define CONFIG_USE_TTY		ttyS1
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
 #define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
 
@@ -41,9 +48,7 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
-#define CFG_MONITOR_BASE	0xfffc0000	/* start of monitor	*/
 #define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
 #define CFG_PERIPHERAL_BASE	0xe0000000	/* internal peripherals	*/
 #define CFG_ISRAM_BASE		0xc0000000	/* internal SRAM	*/
@@ -69,19 +74,11 @@
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon*/
-#define CFG_MALLOC_LEN		(1024 * 1024)	/* Reserve 1024 kB for malloc*/
-
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CONFIG_UART1_CONSOLE	1	/* use of UART1 as console	*/
-#define CONFIG_SERIAL_MULTI     1	/* enable serial multi support	*/
 #define CFG_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE		115200
-
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
 /*-----------------------------------------------------------------------
  * Environment
@@ -137,10 +134,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #undef CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	0x50
@@ -158,65 +152,23 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=taishan\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/taishan/uImage\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc180000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/taishan/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
-	"fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
-	"$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0"	\
-	"dhcp=setenv bootargs $(bootargs) ip=dhcp\0"			\
 	"kozio=bootm 0xffe00000\0"					\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 /*-----------------------------------------------------------------------
  * Networking
  *----------------------------------------------------------------------*/
 #define CONFIG_EMAC_NR_START	2	/* start with EMAC 2 (skip 0&1)	*/
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_PHY_ADDR		0xff	     /* no phy on EMAC0		*/
 #define CONFIG_PHY1_ADDR	0xff	     /* no phy on EMAC1		*/
 #define CONFIG_PHY2_ADDR	0x1
@@ -229,70 +181,12 @@
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
 #define CONFIG_PHY_RESET_DELAY	1000
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
 
 /*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -311,28 +205,4 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */

include/configs/walnut.h

@@ -38,121 +38,43 @@
 #define CONFIG_WALNUT		1	/* ...on a WALNUT board		*/
 					/* ...and on a SYCAMORE board	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		walnut
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/
 
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=walnut\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
-		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/walnut/uImage\0"				\
+/*
+ * Default environment variables
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fff80000\0"					\
 	"ramdisk_addr=fff80000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/walnut/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"				\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
-
-#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 #define CONFIG_HAS_ETH0		1
 
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
-
 #define CONFIG_RTC_DS174x	1	/* use DS1743 RTC in Walnut	*/
 
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
 /*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
 #define CONFIG_SPD_EEPROM      1       /* use SPD EEPROM for setup    */
 
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
 /*
  * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
@@ -167,29 +89,11 @@
 #undef	CFG_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
 #define CFG_BASE_BAUD	    691200
 
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW		1	/* enable loopw command		*/
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -224,13 +128,8 @@
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xFFF80000
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
 
 /*
  * Define here the location of the environment variables (FLASH or NVRAM).
@@ -243,13 +142,6 @@
 #define CFG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
 #endif
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
@@ -335,21 +227,4 @@
  */
 #define SPD_EEPROM_ADDRESS	0x50
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */

include/configs/yosemite.h

@@ -42,6 +42,11 @@
 #define CONFIG_4xx		1	/* ... PPC4xx family		*/
 #define CONFIG_SYS_CLK_FREQ	66666666    /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 #define CONFIG_BOARD_RESET	1	/* call board_reset()		*/
@@ -50,10 +55,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN		(512 * 1024)	/* Reserve 512 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE	        0x00000000	    /* _must_ be 0	*/
 #define CFG_FLASH_BASE	        0xfc000000	    /* start of FLASH	*/
 #define CFG_PCI_MEMBASE	        0xa0000000	    /* mapped pci memory*/
 #define CFG_PCI_MEMBASE1        CFG_PCI_MEMBASE  + 0x10000000
@@ -84,14 +85,9 @@
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CFG_EXT_SERIAL_CLOCK	11059200 /* use external 11.059MHz clk	*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI     1
 /*define this if you want console on UART1*/
 #undef CONFIG_UART1_CONSOLE
 
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -142,10 +138,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -167,72 +160,22 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_YELLOWSTONE
-#define CONFIG_HOSTNAME		yosemite
-#define CFG_BOOTFILE		"bootfile=/tftpboot/yosemite/uImage\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME		yellowstone
-#define CFG_BOOTFILE		"bootfile=/tftpboot/yellowstone/uImage\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CFG_BOOTFILE							\
-	CFG_ROOTPATH							\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"bootfile=/tftpboot/${hostname}/uImage\0"			\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc180000\0"					\
-	"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0"		\
-	"update=protect off fff80000 ffffffff;era fff80000 ffffffff;"	\
-		"cp.b 200000 fff80000 80000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_NET_MULTI        1	/* required for netconsole      */
-#define CONFIG_PHY1_ADDR        3
 #define CONFIG_HAS_ETH0		1	/* add support for "ethaddr"	*/
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
-
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+#define CONFIG_PHY1_ADDR        3
 
 /* Partitions */
 #define CONFIG_MAC_PARTITION
@@ -263,36 +206,11 @@
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif
 
-
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
 
 #ifdef CONFIG_440EP
     #define CONFIG_CMD_USB
@@ -300,36 +218,6 @@
     #define CONFIG_CMD_EXT2
 #endif
 
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on	        */
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI          1       /* support kdi files            */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -347,13 +235,6 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
@@ -370,21 +251,4 @@
 
 #define CFG_BCSR5_PCI66EN	0x80
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */

include/configs/yucca.h

@@ -44,6 +44,12 @@
 #define EXTCLK_50		50000000
 #define EXTCLK_83		83333333
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		yucca
+#include "amcc-common.h"
+
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 #undef  CONFIG_STRESS
@@ -52,9 +58,7 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xfff00000	/* start of FLASH	*/
-#define CFG_MONITOR_BASE	0xfffb0000	/* start of monitor	*/
 #define CFG_PERIPHERAL_BASE	0xa0000000	/* internal peripherals	*/
 #define CFG_ISRAM_BASE		0x90000000	/* internal SRAM	*/
 
@@ -98,24 +102,15 @@
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN		(320 * 1024)	/* Reserve 320 kB for Mon */
-#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc */
-
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI	1
 #undef CONFIG_UART1_CONSOLE
 
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #undef CFG_EXT_SERIAL_CLOCK
 /* #define CFG_EXT_SERIAL_CLOCK	(1843200 * 6) */ /* Ext clk @ 11.059 MHz */
 
-#define CONFIG_BAUDRATE		115200
-
-#define CFG_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
@@ -126,10 +121,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define IIC0_BOOTPROM_ADDR	0x50
 #define IIC0_ALT_BOOTPROM_ADDR	0x54
@@ -152,123 +144,32 @@
 #undef	CFG_ENV_IS_IN_EEPROM		/* ... not in EEPROM		*/
 #define CONFIG_ENV_OVERWRITE	1
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=yucca\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=yucca/uImage\0"					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=E7F10000\0"					\
 	"ramdisk_addr=E7F20000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 yuca/u-boot.bin\0"				\
-	"update=protect off 2:4-7;era 2:4-7;"				\
-		"cp.b ${fileaddr} FFFB0000 ${filesize};"		\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:EP:EP\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
-
 #define	CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
-#undef CONFIG_NET_MULTI
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
 #define CONFIG_PHY_RESET_DELAY	1000
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP				/* undef to save memory		*/
-#define CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address		*/
-#define CFG_EXTBDINFO		1		/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
 /*-----------------------------------------------------------------------
  * FLASH related
@@ -317,26 +218,6 @@
 /* Support for Intel 82557/82559/82559ER chips. */
 #define CONFIG_EEPRO100
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/*Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
 /* FB Divisor selection */
 #define FPGA_FB_DIV_6		6
 #define FPGA_FB_DIV_10		10
@@ -538,10 +419,4 @@
 #define PERIOD_33_33MHZ		30000	/* 30ns */
 #define PERIOD_25_00MHZ		40000	/* 40ns */
 
-/*---------------------------------------------------------------------------*/
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */