Merge with git://www.denx.de/git/u-boot.git

CHANGELOG

@@ -1,3 +1,831 @@
+commit 6923565db12af34fd5e02d354ee65a8c78ac460f
+Author: Detlev Zundel <dzu@denx.de>
+Date:	Fri Apr 20 12:01:47 2007 +0200
+
+    Fix breakage of NC650 board with respect to nand support.
+
+    Signed-off-by: Detlev Zundel <dzu@denx.de>
+
+commit 39f23cd90947639ac278a18ff277ec786b5ac167
+Author: Domen Puncer <domen.puncer@telargo.com>
+Date:	Fri Apr 20 11:13:16 2007 +0200
+
+    [RFC PATCH] icecube/lite5200b: fix OF_TBCLK (timebase-frequency) calculation
+
+    G2 core reference manual says decrementer and time base
+    are decreasing/increasing once every 4 bus clock cycles.
+    Lets fix it, so time in Linux won't run twice as fast
+
+    Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
+    Acked-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 7651f8bdbba03bb0b4f241e2d2c4cb65b230bd56
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Thu Apr 19 23:14:39 2007 -0400
+
+    Fix serious pointer bug with bootm and reserve map.
+
+    What was suppose to be a stack variable was declared as a pointer,
+      overwriting random memory.
+    Also moved the libfdt.a requirement into the main Makefile.  That is
+      The U-Boot Way.
+
+commit 37837828d89084879bee2f2b8c7c68d4695940df
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 18 17:49:29 2007 +0200
+
+    Clenaup, update CHANGELOG
+
+    Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit fd094c6379e2ef8a4d0ceb5640b24cb0c8d04449
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 18 17:20:58 2007 +0200
+
+    Update CHANGELOG
+
+    Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 2a26ec4732efd7a308d0bbc97714c1d75ef1173b
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 18 17:07:26 2007 +0200
+
+    Cleanup, update CHANGELOG
+
+    Sigend-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 5f6c732affea9647762d27a4617a2ae64c52dceb
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 18 16:17:46 2007 +0200
+
+    Update CHANGELOG
+
+commit ad4eb555671d97f96dc56eab55103b1f86874b01
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 18 14:30:39 2007 +0200
+
+    MCC200 board: remove warning which is obsolete after PSoC firmware changes
+
+    Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 3747a3f010b2b1442dec3e871c69788b6017aaae
+Author: Domen Puncer <domen.puncer@telargo.com>
+Date:	Wed Apr 18 12:11:05 2007 +0200
+
+    [PATCH] icecube/lite5200b: document wakeup from low-power support
+
+    Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
+
+commit e673226ff9d6aa91b47ceac74b8c13770b06bb37
+Author: Stefan Roese <sr@denx.de>
+Date:	Wed Apr 18 12:07:47 2007 +0200
+
+    ppc4xx: Update Acadia to not setup PLL when booting via bootstrap EEPROM
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 90e6f41cf09fc98f6ccb510e183d53ab8546cf2f
+Author: Stefan Roese <sr@denx.de>
+Date:	Wed Apr 18 12:05:59 2007 +0200
+
+    ppc4xx: Add output for bootrom location to 405EZ ports
+
+    Now 405EZ ports also show upon bootup from which boot device
+    they are configured to boot:
+
+    U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)
+
+    CPU:   AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
+	   Bootstrap Option E - Boot ROM Location EBC (32 bits)
+	   16 kB I-Cache 16 kB D-Cache
+    Board: Acadia - AMCC PPC405EZ Evaluation Board
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 9c00dfb0bf89c8c23e8af5b5bdf49cf66d769f85
+Author: Peter Pearse <peter.pearse@arm.com>
+Date:	Tue Apr 17 13:30:33 2007 +0100
+
+    Move ppearse to ARM board list
+    Add Konstantin Kletschke for scb9328.
+    Signed-off-by: Peter Pearse <peter.pearse@arm.com>
+
+commit d3832e8fe1b214ec62424eac36cfda9fc56d21b3
+Author: Domen Puncer <domen.puncer@telargo.com>
+Date:	Mon Apr 16 14:00:13 2007 +0200
+
+    [PATCH] icecube/lite5200b: wakeup from low-power support
+
+    U-Boot part of Lite5200b low power mode support.
+    Puts SDRAM out of self-refresh and transfers control to
+    address saved at physical 0x0.
+
+    Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
+    Acked-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit f35a53fc7b0c79fcfe7bdc01163c4b34aaba1460
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sun Apr 15 13:54:26 2007 -0400
+
+    Fix the ft_cpu_setup() property settings.
+
+    Use "setter" functions instead of flags, cleaner and more flexible.
+    It also fixes the problem noted by Timur Tabi that the ethernet MAC
+    addresses were all being set incorrectly to the same MAC address.
+
+commit c28abb9c614f65ce2096cc4a66fc886c77d0e5a4
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Apr 14 22:51:24 2007 -0400
+
+    Improve the bootm command for CONFIG_OF_LIBFDT
+
+    In bootm, create the "/chosen" node only if it doesn't already exist
+      (better matches the previous behavior).
+    Update for proper reserved memory map handling for initrd.
+
+commit 3f9f08cf91c8a6949a5d78a18bd3d8df7b86d888
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Apr 14 22:46:41 2007 -0400
+
+    Add some utilities to manipulate the reserved memory map.
+
+commit 8048cdd56f04a756eeea4951f402bf5cc33785db
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Sat Apr 14 21:16:54 2007 +0200
+
+    Update CHANGELOG
+
+commit 8e6875183cdca91c134408d119d4abcd48ef6856
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 18:56:46 2006 +0100
+
+    AVR32: Enable MMC support
+
+    Set up the portmux for the MMC interface and enable the MMC driver
+    along with support for DOS partitions, ext2 and FAT filesystems.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit fc26c97bb6df41b4a95662c34054fe912387bf38
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Fri Jan 20 10:03:53 2006 +0100
+
+    Atmel MCI driver
+
+    Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs.
+
+    The AT91 ARM-based CPUs use basically the same hardware, so it should
+    be possible to share this driver, but no effort has been made so far.
+
+    Hardware documentation can be found in the AT32AP7000 data sheet,
+    which can be downloaded from
+
+    http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 05fdab1ef6a10d049a50021a86f1226f444d9b9f
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 18:55:37 2006 +0100
+
+    AVR32: Add clk and gpio infrastructure for mmci
+
+    Implement functions for configuring the mmci pins, as well as
+    functions for getting the clock rate of the mmci controller.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 7fac3f69e9f05c5e5326681976c35d129324c4de
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 18:53:56 2006 +0100
+
+    Enable partition support with MMC
+
+    Include implementations of init_part() and get_partition_info() when
+    CONFIG_MMC is set.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 9a24f477a1ed5bb0f74377c985d754ebbfa44872
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 17:14:30 2006 +0100
+
+    AVR32: Enable networking
+
+    Implement MACB initialization for AVR32 and ATSTK1000, and turn
+    everything on, including the MACB driver.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 5c1fe1ffffd1750a7e47e5a2e2cd600c00e4f009
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Fri Jan 20 10:03:34 2006 +0100
+
+    Atmel MACB ethernet driver
+
+    Driver for the Atmel MACB on-chip ethernet controller.
+
+    This driver has been tested on the ATSTK1000 board with a AT32AP7000
+    CPU. It should probably work on AT91SAM926x as well with some minor
+    modifications.
+
+    Hardware documentation can be found in the AT32AP7000 data sheet,
+    which can be downloaded from
+
+    http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit b4ec9c2d43d894729bb633bfdbdfa95a962c1556
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 16:56:14 2006 +0100
+
+    AVR32: Add clk and gpio infrastructure for macb0 and macb1
+
+    Implement functions for configuring the macb0 and macb1 pins, as
+    well as functions for getting the clock rate of the various
+    busses the macb ethernet controllers are connected to.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit d5acb95b16a0a74c643524342c3437e765426d05
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 15:39:15 2006 +0100
+
+    AVR32: Implement simple DMA memory allocator
+
+    Implement dma_alloc_coherent() which returns cache-aligned
+    uncacheable memory.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 91975b0fea773c9e681fea8cf3349669f27685ee
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 15:46:02 2006 +0100
+
+    Import <linux/mii.h> from the Linux kernel
+
+    Instead of creating yet another set of MII register definitions
+    in the macb driver, here's a complete set of definitions for everyone
+    to use.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 1b804b229556a4d862da93c0ec94e79419364b2c
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Wed Mar 21 19:47:36 2007 +0100
+
+    AVR32: Include more commands for ATSTK1000
+
+    Include the imi, imls and jffs commands sets by default on ATSTK1000.
+    Also define CONFIG_BOOTARGS to something more useful, define
+    CONFIG_BOOTCOMMAND and enable autoboot by default.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 9c0deb5ae3ea0189f2e08ac29ef1316f1fb8548d
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Wed Mar 21 19:44:48 2007 +0100
+
+    AVR32: Provide a definition of struct stat
+
+    Copy the definition of struct stat from the Linux kernel.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 12f099c08167a7a51aeee623bc16dafd0841271c
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Dec 17 14:46:06 2006 +0100
+
+    AVR32: Use initdram() instead of board_init_memories()
+
+    Conform to the "standard" interface and use initdram() instead of
+    board_init_memories() on AVR32. This enables us to get rid of the
+    sdram_size member of the global_data struct as well.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 1f4f2121c2685182eb87fa9a9b799d1917387a1c
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Mon Nov 20 15:53:10 2006 +0100
+
+    AVR32: Relocate u-boot to SDRAM
+
+    Relocate the u-boot image into SDRAM like everyone else does. This
+    means that we can handle much larger .data and .bss than we used to.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit df548d3c3e2bbc40258713167859ffc2ce99a900
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sun Nov 19 18:06:53 2006 +0100
+
+    AVR32: Resource management rewrite
+
+    Rewrite the resource management code (i.e. I/O memory, clock gating,
+    gpio) so it doesn't depend on any global state. This is necessary
+    because this code is heavily used before relocation to RAM, so we
+    can't write to any global variables.
+
+    As an added bonus, this makes u-boot's memory footprint a bit smaller,
+    although some functionality has been left out; all clocks are enabled
+    all the time, and there's no checking for gpio line conflicts.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 03d1e1365796cd15d1726e8a51fd8b5be50b2fe9
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sat Nov 18 18:01:13 2006 +0100
+
+    AVR32: Clean up memory-map.h for at32ap7000
+
+    Convert spaces to tabs (must have missed this one last time around),
+    sort the entries by address and group them together by bus
+    connectivity.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 28c699ef69f4b6cdf252e4747b7b590028a88981
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sat Nov 18 17:32:31 2006 +0100
+
+    AVR32: Build position-independent u-boot
+
+    Add -fPIC -mno-init-got to the avr32-specific CFLAGS to make u-boot
+    position independent. This will make relocation a lot easier.
+
+    -mno-init-got means that gcc shouldn't emit code to load the GOT
+    address into r6 in every function prologue. We do it once and for
+    all in the early startup assembly code, so enabling this option
+    makes u-boot a bit faster and smaller.
+
+    The assembly parts have always been position-independent, so no code
+    changes should be necessary.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 5374b36de91d006d1df9536259fa9f66b01aa3aa
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sat Nov 18 17:24:31 2006 +0100
+
+    AVR32: Use avr32-linux- cross-compilation prefix by default
+
+    It doesn't really matter which toolchain you use to compile u-boot,
+    but the avr32-linux one is probably what most people have installed.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit c841beeddebece0039e724fb27f4d1a39ee1c6b6
+Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
+Date:	Sat Nov 18 17:15:30 2006 +0100
+
+    AVR32: Split start_u_boot into board_init_f and board_init_r
+
+    Split the avr32 initialization code into a function to run before
+    relocation, board_init_f and a function to run after relocation,
+    board_init_r. For now, board_init_f simply calls board_init_r
+    at the end.
+
+    Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
+
+commit 37403005cfe6bb13964d450f6a48a0b0f2f7017e
+Author: Heiko Schocher <hs@pollux.denx.de>
+Date:	Sat Apr 14 05:26:48 2007 +0200
+
+    [Fix]	Set the LED status register on the UC101 for the LXT971 PHY.
+	    clear the Display after reset.
+
+    Signed-off-by: Heiko Schocher <hs@denx.de>
+
+commit 7882751c78b7ecabfd49b0eff8de27661c71f16c
+Author: Denis Peter <d.peter@mpl.ch>
+Date:	Fri Apr 13 09:13:33 2007 +0200
+
+    [PATCH] Fix bugs in cmd_ide.c and cmd_scsi.c
+
+    Fix bug introduced by "Fix get_partition_info() parameter error in all
+    other calls" from 2005-03-04 in cmd_ide.c and cmd_scsi.c, which prevented
+    to use diskboot or scsiboot form another device than 0.
+
+    Signed-off-by: Denis Peter <d.peter@mpl.ch>
+
+commit 0b94504d22e70f537c17a0d38c87edb6e370977d
+Author: Greg Lopp <lopp@pobox.com>
+Date:	Fri Apr 13 08:02:24 2007 +0200
+
+    [PATCH] Fix use of "void *" for block dev read/write buffer pointers
+
+    Signed-of-by: Greg Lopp <lopp@pobox.com>
+    Acked-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 2ad3aba01d37b72e7c957b07e102fccd64fe6d13
+Author: Jeffrey Mann <mannj@embeddedplanet.com>
+Date:	Thu Apr 12 14:15:59 2007 +0200
+
+    ppc4xx: Fix i2c divisor calcularion for PPC4xx
+
+    This patch fixes changes the i2c_init(...) function to use the function
+    get_OPB_freq() rather than calculating the OPB speed by
+    sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is
+    specific per processor. The prior method was not and so was calculating
+    the wrong speed for some PPC4xx processors.
+
+    Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 6c9ba919375db977aaad9146bf320c7afd07ae7a
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 11 17:25:01 2007 +0200
+
+    Update CHANGELOG
+
+    Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 51056dd9863e6a1bc363afbbe1775c58cd967418
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 11 17:22:55 2007 +0200
+
+    Update for SC3 board
+
+    * Make IDE timeout configurable through ide_reset_timeout variable.
+    * Use Newline as "password" string
+    * Use just a single partition in NAND flash
+
+commit 3d98b85800c80dc68227c8f10bf5c93456d6d054
+Author: Haiying Wang <haiying.wang@freescale.com>
+Date:	Mon Jan 22 12:37:30 2007 -0600
+
+    Add PIXIS FPGA support for MPC8641HPCN board.
+
+    Move the 8641HPCN's PIXIS code to the new directory
+    board/freescale/common/ as it will be shared by
+    future boards not in the same processor family.
+
+    Write a "pixis_reset" command that utilizes the FPGA
+    reset sequencer to support alternate soft-reset options
+    such as using the "alternate" flash bank, enabling
+    the watch dog, or choosing different CPU frequencies.
+
+    Add documentation for the pixis_reset to README.mpc8641hpcn.
+
+    Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
+    Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 64dbbd40c58349b64f43fd33dbb5ca0adb67d642
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Fri Apr 6 14:19:43 2007 -0400
+
+    Moved fdt command support code to fdt_support.c
+
+    ...in preparation for improving the bootm command's handling of fdt blobs.
+    Also cleaned up some coding sloppiness.
+
+commit 6679f9299534e488a171a9bb8f9bb891de247aab
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Fri Apr 6 14:17:14 2007 -0400
+
+    libfdt: Make fdt_check_header() public
+
+    Changed _fdt_check_header() to fdt_check_header() and made it part of
+    the interface - it is a useful routine.
+
+    Also did some asthetics cleanup to the include files (headers).
+
+commit c0707ce65677650b5ceab0500ee50ae5168afef2
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:34:06 2007 +0800
+
+    [Blackfin][PATCH] Kill off a bunch of common local prototypes
+
+commit 7b7e30aa64bb6657a1bfd32fdbdbfeb561e6a48d
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:33:04 2007 +0800
+
+    [Blackfin][PATCH] Fix dynamic CPLB generation issue
+
+commit 0445e3a264251d75b1be45ef713c70726a2952f0
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:31:47 2007 +0800
+
+    [Blackfin][PATCH] minior cleanup
+
+commit 155fd766573981090e638b493d5857562151862e
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:31:18 2007 +0800
+
+    [Blackfin][PATCH] Fix copyright and update license
+
+commit 9fd437bbd75d282f899e1da50be20a2bf38450bc
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:30:25 2007 +0800
+
+    [Blackfin][PATCH] Add BF537 EMAC driver initialization
+
+commit 889256e8604e0c68db1d866d720894dffede9df6
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:29:55 2007 +0800
+
+    [Blackfin][PATCH] call real the system synchronize instruction
+
+commit e0df1c921b788289564e4c1ee7120a6a9cd3ab05
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:29:17 2007 +0800
+
+    [Blackfin][PATCH] remove asm/page.h as we do not actually use/want any of these definitions nor does any other arch include it
+
+commit dfeeab2cd680df047e68e723b246adf6f33bb556
+Author: Aubrey Li <aubrey.adi@gmail.com>
+Date:	Thu Apr 5 18:28:34 2007 +0800
+
+    [Blackfin][PATCH]: fix flash unaligned copy issue
+
+commit 443feb740584e406efa203af909fe2926608e8d5
+Author: Igor Marnat <marny@rambler.ru>
+Date:	Wed Mar 21 09:55:01 2007 +0300
+
+    Update usage of 'nc' in README.NetConsole
+
+    Added information about usage of NetConsole on systems where the -l and -p
+    switches are mutually exclusive.
+
+    Signed-off-by: Igor Marnat <marny@rambler.ru>
+    Signed-off-by: Ben Warren <bwarren@qstreams.com>
+
+commit 31c98a88228021b314c89ebb8104fb6473da4471
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 4 02:09:30 2007 +0200
+
+    Minor coding style cleanup.
+
+commit 94abd7c0583ebe01e799b25f451201deeaab550d
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Wed Apr 4 01:49:15 2007 +0200
+
+    Minor cleanup.
+
+commit a65c5768e5537530bd1780af3d3fddc3113a163c
+Author: Stefan Roese <sr@denx.de>
+Date:	Mon Apr 2 10:09:30 2007 +0200
+
+    ppc4xx: Change SysACE address on Katmai
+
+    With this new base address of the Xilinx SystemACE controller
+    the Linux driver will be easier to adapt, since it can now be
+    mapped via the "normal" ioremap() call.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit aea03c4e8c3a21ce43d3faf48a6e6d474c8bdf73
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Mar 31 14:30:53 2007 -0400
+
+    Fix some minor whitespace violations.
+
+commit 213bf8c822de8eecaf69860684469cdaba2e9e6a
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Mar 31 12:23:51 2007 -0400
+
+    Add a flattened device tree (fdt) command (2 of 2)
+
+    Modifications to the existing code to support the new fdt command.
+
+commit 781e09ee6e3e3e392ab362c1f0ef1068adc76e3e
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Mar 31 12:22:10 2007 -0400
+
+    Add a flattened device tree (fdt) command (1 of 2)
+
+    The fdt command uses David Gibson's libfdt library to manipulate as well
+    as print the flattened device tree.  This patch is the new command,
+    the second part is the modifications to the existing code.
+
+commit 3af0d587d93e0be5f96e1b30fa41e662f8b0803e
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Mar 31 12:13:43 2007 -0400
+
+    libfdt: Enhanced and published fdt_next_tag()
+
+    Enhanced the formerly private function _fdt_next_tag() to allow stepping
+      through the tree, used to produce a human-readable dump, and made
+      it part of the published interface.
+    Also added some comments.
+
+commit fa3a74cec73dfd06a5ae35a9a3368200273aaa71
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Mar 31 12:05:39 2007 -0400
+
+    libfdt: Customizations for use by u-boot.
+
+    Changes to David Gibson's original source to fit into u-boot's
+    environment.  No functionality changes.
+
+commit 35748177c64a4a83a00057e93bb33e40278a2a96
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Mar 31 12:00:56 2007 -0400
+
+    libfdt: Import libfdt source (2 of 2)
+
+    This adds the applicable libfdt source files (unmodified) and a README
+    to explain where the source came from.
+
+commit 7cd5da0fe877e7171a4cdd44880bce783132871a
+Author: Gerald Van Baren <vanbaren@cideas.com>
+Date:	Sat Mar 31 11:59:59 2007 -0400
+
+    libfdt: Import libfdt source (1 of 2)
+
+    This adds the applicable libfdt source files (unmodified) and a README
+    to explain where the source came from.
+
+commit da6ebc1bc082cbe3b6bbde079cafe09f7ebbad4b
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 31 13:16:23 2007 +0200
+
+    ppc4xx: Update Katmai bootstrap command
+
+    Now the DDR2 frequency is also 2*PLB frequency when 166MHz PLB
+    is selected.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit cabee756a6532986729477c3cc1ea16ef8517ad2
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 31 13:15:06 2007 +0200
+
+    ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
+
+    Additional RAM information is now printed upon powerup, like
+    DDR2 frequency and CAS latency.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 60723803431ac75cad085690789e433d5ab9174e
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 31 08:48:36 2007 +0200
+
+    ppc4xx: Change Yucca config file to support ECC
+
+    With the updated 44x DDR2 driver the Yucca board now supports
+    ECC generation and checking.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 490e5730c674b20d708b783a2c5ffd7208f83873
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 31 08:47:34 2007 +0200
+
+    ppc4xx: Fix "bootstrap" command for Katmai board
+
+    The board specific "bootstrap" command is now fixed and can
+    be used for the AMCC Katmai board to configure different
+    CPU/PLB/OPB frequencies.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 94f54703c3a776ec23e427ca2a16e0a79a5d50c1
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 31 08:46:08 2007 +0200
+
+    ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
+
+    Fix a bug in the auto calibration routine. This driver now runs
+    more reliable with the tested modules. It's also tested with
+    167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 342cd097be1e7affe82f42ab3da220959a699e64
+Author: Michal Simek <monstr@monstr.eu>
+Date:	Fri Mar 30 22:52:09 2007 +0200
+
+    [PATCH] Clean include dependence
+
+commit 6f934210fb293fde2cfb4251c6d96fdc58b6a906
+Author: Michal Simek <monstr@monstr.eu>
+Date:	Fri Mar 30 22:42:45 2007 +0200
+
+    [CLEAN] Remove inefficient Suzaku code
+
+commit 430f1b0f9a670c2f13eaa52e66a10db96dd3647d
+Author: Stefan Roese <sr@denx.de>
+Date:	Wed Mar 28 15:03:16 2007 +0200
+
+    Merge some AMCC make targets to keep the top-level Makefile smaller
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 0c75c9d84307a9f1cbe1ff0c4d8937ee3a96475e
+Author: Stefan Roese <sr@denx.de>
+Date:	Wed Mar 28 14:52:12 2007 +0200
+
+    i2c: Enable "old" i2c commands even when CONFIG_I2C_CMD_TREE is defined
+
+    The "old" i2c commands (iprobe, imd...) are now compiled in again,
+    even when the i2c command tree is enabled via the CONFIG_I2C_CMD_TREE
+    config option.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 5da048adf44bea5e3b94080d02903c2e3fe7aa4a
+Author: Michal Simek <monstr@monstr.eu>
+Date:	Tue Mar 27 00:32:16 2007 +0200
+
+    PATCH: Resolve GPL license problem
+
+commit 1798049522f594013aea29457d46794298c6ae15
+Author: Michal Simek <root@monstr.eu>
+Date:	Mon Mar 26 01:39:07 2007 +0200
+
+    Support for XUPV2P board
+    Reset support
+    BSP autoconfig support
+
+commit 0d974d5297349504a2ddfa09314be573b5df320a
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 24 15:57:09 2007 +0100
+
+    [PATCH] Add 4xx GPIO functions
+
+    This patch adds some 4xx GPIO functions. It also moves some of the
+    common code and defines into a common 4xx GPIO header file.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 2db633658bbf366ab0c8dad7a0727e1fb2ae6b11
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 24 15:55:58 2007 +0100
+
+    [PATCH] Small Sequoia cleanup
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 3cb86f3e40d2a80356177434a99f75bc8baa9caf
+Author: Stefan Roese <sr@denx.de>
+Date:	Sat Mar 24 15:45:34 2007 +0100
+
+    [PATCH] Clean up 40EZ/Acadia support
+
+    This patch cleans up all the open issue of the preliminary
+    Acadia support.
+
+    Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 6eb1df835191d8ce4b81d5af40fa8e0fbe78e997
+Author: Jon Loeliger <jdl@freescale.com>
+Date:	Tue Dec 12 11:02:20 2006 -0600
+
+    Fix 8641HPCN problem with ld version 2.16
+
+    (Dot outside sections problem).
+
+    This fix is in the spirit of 807d5d7319330e336ab34a5623c5e0d73b87d540.
+
+    Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 9964a4dd0d4ef5a037febaebf1aa494b1a72991c
+Author: Haiying Wang <haiying.wang@freescale.com>
+Date:	Thu Dec 7 10:35:55 2006 -0600
+
+    Set Rev 2.x 86xx PIC in mixed mode.
+
+    Prevent false interrupt from hanging Linux as MSR[EE] is set
+    to enable interrupts by changing the PIC out of the default
+    pass through mode into mixed mode.
+
+    Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
+    Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 5a58a73ceb0a4059c42ef64cedbc1a45e0aaa00e
+Author: Jason Jin <jason.jin@freescale.com>
+Date:	Thu Dec 7 10:32:35 2006 -0600
+
+    Add flash cmd function to 8641HPCN ramboot
+
+    Also fixes some commmand for 8641 HPCN ramboot case.
+
+    Signed-off-by: Jason Jin <jason.jin@freescale.com>
+    Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 2ccceacc04b009d923afb7c26189ba2f8a2a5d46
+Author: Ed Swarthout <ed.swarthout@freescale.com>
+Date:	Thu Dec 7 10:34:14 2006 -0600
+
+    Add support for 8641 Rev 2 silicon.
+
+    Without this patch, I am unable to get to the prompt on rev 2 silicon.
+    Only set ddrioovcr for rev1.
+
+    Signed-off-by: Ed Swarthout<ed.swarthout@freescale.com>
+    Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 44ba464b99001f8bd1c456a1e9d59726252f707a
+Author: Wolfgang Denk <wd@denx.de>
+Date:	Thu Mar 22 00:13:12 2007 +0100
+
+    Code cleanup / re-insert previous Copyright entries.
+
+    Signed-off-by: Wolfgang Denk <wd@denx.de>
+
 commit 2a8dfe08359a1b663418b2faa1da1d7bce34d302
 Author: Wolfgang Denk <wd@denx.de>
 Date:	Wed Mar 21 23:26:15 2007 +0100
@@ -148,6 +976,38 @@ Date:	Mon Mar 12 00:25:14 2007 +0800
 
     [Blackfin][PATCH] code cleanup
 
+commit cfc67116a706fd18b8f6a9c11a16753c5626d689
+Author: Michal Simek <monstr@monstr.eu>
+Date:	Sun Mar 11 13:48:24 2007 +0100
+
+    [Microblaze][PATCH] part 2
+    timer support
+    interrupt controller support
+    flash support
+    ethernet support
+    cache support
+    board information support
+    env support
+    booting image support
+
+    adding support for Xilinx ML401
+
+commit 76316a318de91f6184e7c22a10e02d275ade2441
+Author: Michal Simek <monstr@monstr.eu>
+Date:	Sun Mar 11 13:42:58 2007 +0100
+
+    [Microblaze][PATCH]
+    timer support
+    interrupt controller support
+    flash support
+    ethernet support
+    cache support
+    board information support
+    env support
+    booting image support
+
+    adding support for Xilinx ML401
+
 commit 8db13d63157811c839d15a313d9f2d2f5fd10af3
 Author: Aubrey Li <aubrey.adi@gmail.com>
 Date:	Sat Mar 10 23:49:29 2007 +0800
@@ -282,6 +1142,24 @@ Date:	Thu Mar 8 10:06:09 2007 +0100
 
     Signed-off-by: Stefan Roese <sr@denx.de>
 
+commit 83853178bd36bca6f0f8f1331476620c84a587fc
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date:	Wed Mar 7 12:14:50 2007 -0600
+
+    net - Support ping reply when processing net-loop
+
+    Add ICMP_ECHO_REQUEST packet support by responding with a ICMP_ECHO_REPLY.
+
+    This permits the ping command to test the phy interface when the phy
+    is put in loopback mode (typically by setting register 0 bit 14).
+
+    It also allows the port to respond to an external ping when u-boot is
+    processing some other net command (such as tftp).  This is useful when
+    tftp appears to hang.
+
+    Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+    Signed-off-by: Ben Warren <bwarren@qstreams.com>
+
 commit fa1aef15bcd47736687be1af544506e90fba545d
 Author: Stefan Roese <sr@denx.de>
 Date:	Wed Mar 7 16:43:00 2007 +0100
@@ -358,6 +1236,12 @@ Date:	Tue Mar 6 07:47:04 2007 +0100
 
     Signed-off-by: Stefan Roese <sr@denx.de>
 
+commit 647d3c3eed0da1d1505eecabe0b0fab96f956e68
+Author: Wolfgang Denk <wd@pollux.denx.de>
+Date:	Sun Mar 4 01:36:05 2007 +0100
+
+    Some code cleanup.
+
 commit 781e026c8aa6f7e9eb5f0e72cc4d20971219b148
 Author: Kim Phillips <kim.phillips@freescale.com>
 Date:	Wed Feb 28 00:02:04 2007 -0600
@@ -1229,6 +2113,15 @@ Date:	Tue Jan 23 13:25:22 2007 +0100
     [ColdFire MCF5271 family] Add CPU detection based on the value of Chip
     Identification Register (CIR).
 
+commit fdef388758506765d4d6a7155c8f1584c63ff581
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Mon Jan 22 13:19:21 2007 +0800
+
+    use  CFG_WRITE_SWAPPED_DATA define instead of define CFG_FLASH_CFI_SWAP
+    The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
+    fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
+    mpc7448hpc2 board.
+
 commit a4012396645533aef218354eeba754dff0deace8
 Author: Wolfgang Denk <wd@pollux.denx.de>
 Date:	Fri Jan 19 23:08:39 2007 +0100
@@ -1644,6 +2537,72 @@ Date:	Fri Dec 8 16:23:08 2006 +0100
 
     automatic update mechanism
 
+commit 9d27b3a0685ff99fc477983f315c04d49f657a8a
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Mon Dec 4 17:56:59 2006 +0800
+
+    Slight code clean up.
+    Add comments, delete duplicate define and remove spaces.
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 4dbcd69e3e2776ea334590d5768e3692c5fae5c1
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Mon Dec 4 17:54:21 2006 +0800
+
+    Introduce PLL_CFG[0:4] table for processor 7448/7447A/7455/7457. The original
+    multiplier table can not refect the real PLL clock behavior of these
+    processors. Please refer to the hardware specification for detailed
+    information of the corresponding processors.
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 4efe20c9579011d9987f62ed7d35ee8cdc1cf0e0
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Mon Dec 4 14:46:23 2006 +0800
+
+    Remove the static MAC address, ip address, server ip, netmask and
+    gateway ip for network setting.
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 6f12c61cf31ed73d72ddfcfc712a854a3a177aaf
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Mon Dec 4 14:33:08 2006 +0800
+
+    Remove the duplicate memory test code for mpc744ihpc2 board.
+    If a memory test is needed, please use the functions in
+    post/memory.c or memtest command.
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit c9c1eeed7dd193fa65fb194654132040d49d4d3a
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Fri Dec 1 19:01:25 2006 +0800
+
+    Fix the exception occuring in RAM table search issue.
+    The original search_one_table() function code can only processes the search
+    for the exception occurring in FLASH/ROM, because the exception and fixup
+    table usually locate in FLASH. If the exception address is also in
+    FLASH, it will be OK.
+    If the exception occurs in RAM, after the u-boot relocation, a
+    relocation offset should be added.
+
+    clean up the code in cpu/74xx_7xx/cpu.c
+
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit ee311214e0d216f904feea269599d0934bf71f23
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Fri Dec 1 11:47:36 2006 +0800
+
+    Clean up the code according to codestyle:
+    (1) remove some C++ comments.
+    (2) remove trailing white space.
+    (3) remove trailing empty line.
+    (4) Indentation by table.
+    (5) remove {} in one line condition.
+    (6) add space before '(' in function call.
+    Remove some weird printf () output.
+    Add necessary comments.
+    Modified Makefile to support building in a separate directory.
+
 commit dd520bf314c7add4183c5191692180f576f96b60
 Author: Wolfgang Denk <wd@pollux.denx.de>
 Date:	Thu Nov 30 18:02:20 2006 +0100
@@ -2350,12 +3309,191 @@ Date:	Thu Sep 7 07:39:46 2006 -0700
 
     Signed-off-by: Nick Spence <nick.spence@freescale.com>
 
+commit 4831c8b8a97799da77923d6bbb4c260c0d45521c
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Fri Nov 3 13:10:00 2006 +0800
+
+    Remove some unused CFG define.
+    undef CFG_DRAM_TEST
+
+commit 99c09c4dec34f77c243bf51bea532e3f339410ad
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Fri Nov 3 13:07:36 2006 +0800
+
+    Change the TEXT_BASE from 0xFFF00000 to 0xFF000000.
+    Both work. 0xFF000000 seems more reasonable.
+
 commit c59200443072353044aa4bf737a5a60f9a9af231
 Author: Wolfgang Denk <wd@pollux.denx.de>
 Date:	Thu Nov 2 15:15:01 2006 +0100
 
     Release U-Boot 1.1.6
 
+commit c1fbe4103a0d6c8957f912af902d705ba67836f2
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 19:14:48 2006 +0800
+
+    This patch comes from Yuli's posted patch on 8/8/2006
+    titled "CFI Driver Little-Endian write Issue".
+
+    http://sourceforge.net/mailarchive/message.php?msg_id=36311999
+
+    If that patch applied, please discard this one.
+    Until now , I do not see his patch is applied. So please apply this one.
+
+    Signed-off-by: Yuli Barcohen <yuli@arabellasw.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit b825f158e449e1e9cf74c08e572955e122394c96
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 19:12:31 2006 +0800
+
+    Tsi108 on chip i2c support.
+
+    The i2c  Interface provides a master-only, serial interface that can be
+    used for initializing Tsi108/Tsi109 registers from an EEPROM after a
+    device reset.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 9226e7d6f09b9a1ac074cd918c81225a4689bba8
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 19:11:06 2006 +0800
+
+    Tsi108 on chip pci controller support.
+
+    If there is no pci card, the tsi108/109 pci configure read will
+    cause a machine check exception to the processor. PCI error should
+    also be cleared after the read.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit d1927cee977126e547ceeba23e4f978f377cfb8f
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 19:08:55 2006 +0800
+
+    Tundra tsi108 on chip Ethernet controller support.
+
+    The following is a brief description of the Ethernet controller:
+    The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
+    Gigabit Ethernet ports,E0 and E1.  It uses a single Management interface
+    to manage the two physical connection devices (PHYs).  Each Ethernet port
+    has its own statistics monitor that tracks and reports key interface
+    statistics.  Each port supports a 256-entry hash table for address
+    filtering.	In addition, each port is bridged to the Switch Fabric
+    through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
+
+    Each Ethernet port also has a pair of internal Ethernet DMA channels to
+    support the transmit and receive data flows.  The Ethernet DMA channels
+    use descriptors set up in memory, the memory map of the device, and
+    access via the Switch Fabric.  The Ethernet Controller?s DMA arbiter
+    handles arbitration for the Switch Fabric.	The Controller also
+    has a register businterface for register accesses and status monitor
+    control.
+
+    The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
+    modes.  The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
+    The GMII and TBI modes are used to connect with Gigabit PMDs.  Internal
+    data flows to and from the Ethernet Controller through the Switch Fabric.
+
+    Each Ethernet port uses its transmit and receive DMA channels to manage
+    data flows through buffer descriptors that are predefined by the
+    system (the descriptors can exist anywhere in the system memory map).
+    These descriptors are data structures that point to buffers filled
+    with data ready to transmit over Ethernet, or they point to empty
+    buffers ready to receive data from Ethernet.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 78aa0c3427f3ecdeb34aabfbbe2dd23b6ad8f40e
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 19:01:33 2006 +0800
+
+    Tundra tsi108 header file.
+
+    The Tundra Semiconductor Corporation (Tundra) Tsi108 is a host bridge for
+    PowerPC processors that offers numerous system interconnect options for
+    embedded application designers. The Tsi108 can interconnect 60x or
+    MPX processors to PCI/X peripherals, DDR2-400 memory, Gigabit Ethernet,
+    and Flash. Provided the macro define for tsi108 chip.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 87c4db09699c6b89176b31004afcb83eb1585d47
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 18:59:15 2006 +0800
+
+    Add  mpc7448hpc2  (mpc7448 + tsi108)  board associated code support.
+    mpc7448hpc2 board support high level code:tsi108 init + mpc7448hpc2.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 27801b8ab11c61b577e45742a515bb3b23b80241
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 18:57:21 2006 +0800
+
+    Add  mpc7448hpc2  (mpc7448 + tsi108)  board associated code support.
+    Make ,config.mk and link file for the mpc7448hpc2 board.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit c6411c0c3bbc79f9ba8aef58296a42d8f9d8a0a6
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 18:55:04 2006 +0800
+
+    Add  mpc7448hpc2  (mpc7448 + tsi108)  board associated code support.
+    The mpc7448hpc2 board support header file.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 625bb5ddb50b243f931262ca8c46956409471917
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 18:52:21 2006 +0800
+
+    Add  mpc7448hpc2  (mpc7448 + tsi108)  board associated code support.
+    The mpc7448hpc2 board support low level assemble language init code.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 4c52783b3d024e153c4972b97332e314bc3bdc46
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 18:49:51 2006 +0800
+
+    General code modification for mpc7448hpc2 board support.
+    1. Add 7447A and 7448 processor support.
+    2. Add the following flags.
+
+    CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically
+    (such as by switch on board), this flag should be set.
+
+    CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot
+    relocates to RAM, this flag should be set.
+
+    CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the
+    system hang in exception, this flag should be set.
+
+    There is a design issue for tsi108/109 pci configure  read. When pci scan
+    the slots, if there is no pci card, the tsi108/9 will cause a machine
+    check exception for mpc7448 processor.
+
+    Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 69366bf42f22d67efce8da3f8c40a43d4a3c2695
+Author: roy zang <tie-fei.zang@freescale.com>
+Date:	Thu Nov 2 18:34:47 2006 +0800
+
+    Add README file for mpc7448hpc2 board.
+    Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
 commit 25721b5cec2be4bce79cfade17ec8f6aa1e67526
 Author: Bartlomiej Sieka <tur@semihalf.com>
 Date:	Wed Nov 1 02:04:38 2006 +0100

CREDITS

@@ -474,3 +474,8 @@ N: Timur Tabi
 E: timur@freescale.com
 D: Support for MPC8349E-mITX
 W: www.freescale.com
+
+N: Michal Simek
+E: monstr@monstr.eu
+D: Support for Microblaze, ML401, XUPV2P board
+W: www.monstr.eu

MAINTAINERS

@@ -257,15 +257,6 @@ Frank Panno <fpanno@delphintech.com>
 
 	ep8260			MPC8260
 
-Peter Pearse <peter.pearse@arm.com>
-	integratorcp		All current ARM supplied &
-				supported core modules
-				- see http://www.arm.com
-				/products/DevTools
-				/Hardware_Platforms.html
-	versatile		ARM926EJ-S
-	versatile		ARM926EJ-S
-
 Denis Peter <d.peter@mpl.ch>
 
 	MIP405			PPC4xx
@@ -444,6 +435,9 @@ Gary Jennejohn <gj@denx.de>
 	smdk2400		ARM920T
 	trab			ARM920T
 
+Konstantin Kletschke <kletschke@synertronixx.de>
+	scb9328			ARM920T
+
 Nishant Kamat <nskamat@ti.com>
 
 	omap1610h2		ARM926EJS
@@ -461,6 +455,15 @@ Rolf Offermanns <rof@sysgo.de>
 
 	shannon			SA1100
 
+Peter Pearse <peter.pearse@arm.com>
+	integratorcp		All current ARM supplied &
+				supported core modules
+				-see http://www.arm.com
+				/products/DevTools
+				/Hardware_Platforms.html
+	versatile		ARM926EJ-S
+	versatile		ARM926EJ-S
+
 Dave Peverley <dpeverley@mpc-data.co.uk>
 
 	omap730p2		ARM926EJS
@@ -564,6 +567,11 @@ Yasushi Shoji <yashi@atmark-techno.com>
 
 	SUZAKU			MicroBlaze
 
+Michal Simek <monstr@monstr.eu>
+
+	ML401			MicroBlaze
+	XUPV2P			MicroBlaze
+
 #########################################################################
 # Coldfire Systems:							#
 #									#

MAKEALL

@@ -155,6 +155,7 @@ LIST_85xx="	\
 LIST_74xx="	\
 	DB64360		DB64460		EVB64260	P3G4		\
 	p3m7448		PCIPPC2		PCIPPC6		ZUMA		\
+	mpc7448hpc2
 "
 
 LIST_7xx="	\
@@ -293,7 +294,7 @@ LIST_nios2="	\
 #########################################################################
 
 LIST_microblaze="	\
-	suzaku
+	suzaku		ml401		xupv2p
 "
 
 #########################################################################

Makefile

@@ -149,7 +149,7 @@ ifeq ($(ARCH),blackfin)
 CROSS_COMPILE = bfin-uclinux-
 endif
 ifeq ($(ARCH),avr32)
-CROSS_COMPILE = avr32-
+CROSS_COMPILE = avr32-linux-
 endif
 endif
 endif
@@ -219,6 +219,7 @@ LIBS += $(shell if [ -d post/cpu/$(CPU) ]; then echo \
 LIBS += $(shell if [ -d post/board/$(BOARDDIR) ]; then echo \
 	"post/board/$(BOARDDIR)/libpost$(BOARD).a"; fi)
 LIBS += common/libcommon.a
+LIBS += libfdt/libfdt.a
 LIBS += $(BOARDLIBS)
 
 LIBS := $(addprefix $(obj),$(LIBS))
@@ -430,6 +431,7 @@ inka4x0_config:	unconfig
 	@$(MKCONFIG) inka4x0 ppc mpc5xxx inka4x0
 
 lite5200b_config	\
+lite5200b_PM_config	\
 lite5200b_LOWBOOT_config:	unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)board/icecube
@@ -438,6 +440,10 @@ lite5200b_LOWBOOT_config:	unconfig
 	@ echo "... DDR memory revision"
 	@ echo "#define CONFIG_MPC5200"		>>$(obj)include/config.h
 	@ echo "#define CONFIG_LITE5200B"	>>$(obj)include/config.h
+	@[ -z "$(findstring _PM_,$@)" ] || \
+		{ echo "#define CONFIG_LITE5200B_PM"	>>$(obj)include/config.h ; \
+		  echo "... with power management (low-power mode) support" ; \
+		}
 	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
 		{ echo "TEXT_BASE = 0xFF000000" >$(obj)board/icecube/config.tmp ; \
 		  echo "... with LOWBOOT configuration" ; \
@@ -1193,44 +1199,31 @@ PPChameleonEVB_HI_33_config:	unconfig
 		}
 	@$(MKCONFIG) -a $(call xtract_4xx,$@) ppc ppc4xx PPChameleonEVB dave
 
-rainier_config:	unconfig
-	@mkdir -p $(obj)include
-	@echo "#define CONFIG_RAINIER" > $(obj)include/config.h
-	@$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
-
-rainier_nand_config:	unconfig
-	@mkdir -p $(obj)include
-	@mkdir -p $(obj)nand_spl
-	@mkdir -p $(obj)board/amcc/sequoia
-	@echo "#define CONFIG_RAINIER" > $(obj)include/config.h
-	@echo "#define CONFIG_NAND_U_BOOT" >> $(obj)include/config.h
-	@echo "Compile NAND boot image for sequoia"
-	@$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
-	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
-	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
-
 sbc405_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx sbc405
 
-sequoia_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) ppc ppc4xx sequoia amcc
+sequoia_config \
+rainier_config: unconfig
+	@mkdir -p $(obj)include
+	@echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
+		tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
 
-sequoia_nand_config:	unconfig
+sequoia_nand_config \
+rainier_nand_config: unconfig
 	@mkdir -p $(obj)include
 	@mkdir -p $(obj)nand_spl
 	@mkdir -p $(obj)board/amcc/sequoia
 	@echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
-	@echo "Compile NAND boot image for sequoia"
-	@$(MKCONFIG) -a sequoia ppc ppc4xx sequoia amcc
+	@echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
+		tr '[:lower:]' '[:upper:]')" >> $(obj)include/config.h
+	@$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 
 sc3_config:unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx sc3
 
-sycamore_config:	unconfig
-	@$(MKCONFIG) -n $@ -a walnut ppc ppc4xx walnut amcc
-
 taishan_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx taishan amcc
 
@@ -1247,8 +1240,10 @@ W7OLMC_config	\
 W7OLMG_config: unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx w7o
 
-walnut_config: unconfig
-	@$(MKCONFIG) $(@:_config=) ppc ppc4xx walnut amcc
+# Walnut & Sycamore images are identical (recognized via PVR)
+walnut_config \
+sycamore_config: unconfig
+	@$(MKCONFIG) -n $@ -a walnut ppc ppc4xx walnut amcc
 
 WUH405_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx wuh405 esd
@@ -1256,12 +1251,11 @@ WUH405_config:	unconfig
 XPEDITE1K_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx xpedite1k
 
-yosemite_config:	unconfig
-	@$(MKCONFIG) $(@:_config=) ppc ppc4xx yosemite amcc
-
-yellowstone_config:	unconfig
+yosemite_config \
+yellowstone_config: unconfig
 	@mkdir -p $(obj)include
-	@echo "#define CONFIG_YELLOWSTONE" > $(obj)include/config.h
+	@echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
+		tr '[:lower:]' '[:upper:]')" >$(obj)include/config.h
 	@$(MKCONFIG) -n $@ -a yosemite ppc ppc4xx yosemite amcc
 
 yucca_config:	unconfig
@@ -1829,6 +1823,9 @@ EVB64260_config	\
 EVB64260_750CX_config:	unconfig
 	@$(MKCONFIG) EVB64260 ppc 74xx_7xx evb64260
 
+mpc7448hpc2_config:  unconfig
+	@$(MKCONFIG) $(@:_config=) ppc 74xx_7xx mpc7448hpc2
+
 P3G4_config: unconfig
 	@$(MKCONFIG) $(@:_config=) ppc 74xx_7xx evb64260
 
@@ -2361,6 +2358,16 @@ suzaku_config:	unconfig
 	@echo "#define CONFIG_SUZAKU 1" >> $(obj)include/config.h
 	@$(MKCONFIG) -a $(@:_config=) microblaze microblaze suzaku AtmarkTechno
 
+ml401_config:	unconfig
+	@ >include/config.h
+	@echo "#define CONFIG_ML401 1" >> include/config.h
+	@./mkconfig -a $(@:_config=) microblaze microblaze ml401 xilinx
+
+xupv2p_config:	unconfig
+	@ >include/config.h
+	@echo "#define CONFIG_XUPV2P 1" >> include/config.h
+	@./mkconfig -a $(@:_config=) microblaze microblaze xupv2p xilinx
+
 #########################################################################
 ## Blackfin
 #########################################################################

README

@@ -164,6 +164,7 @@ Directory Hierarchy:
 - lib_mips	Files generic to MIPS	 architecture
 - lib_nios	Files generic to NIOS	 architecture
 - lib_ppc	Files generic to PowerPC architecture
+- libfdt 	Library files to support flattened device trees
 - net		Networking code
 - post		Power On Self Test
 - rtc		Real Time Clock drivers
@@ -431,12 +432,23 @@ The following options need to be configured:
 		expect it to be in bytes, others in MB.
 		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
 
-		CONFIG_OF_FLAT_TREE
+		CONFIG_OF_LIBFDT / CONFIG_OF_FLAT_TREE
 
 		New kernel versions are expecting firmware settings to be
-		passed using flat open firmware trees.
-		The environment variable "disable_of", when set, disables this
-		functionality.
+		passed using flattened device trees (based on open firmware
+		concepts).
+
+		CONFIG_OF_LIBFDT
+		 * New libfdt-based support
+		 * Adds the "fdt" command
+		 * The bootm command does _not_ modify the fdt
+
+		CONFIG_OF_FLAT_TREE
+		 * Deprecated, see CONFIG_OF_LIBFDT
+		 * Original ft_build.c-based support
+		 * Automatically modifies the dft as part of the bootm command
+		 * The environment variable "disable_of", when set,
+		     disables this functionality.
 
 		CONFIG_OF_FLAT_TREE_MAX_SIZE
 
@@ -449,13 +461,16 @@ The following options need to be configured:
 
 		CONFIG_OF_HAS_BD_T
 
-		The resulting flat device tree will have a copy of the bd_t.
-		Space should be pre-allocated in the dts for the bd_t.
+		 * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
+		 * CONFIG_OF_FLAT_TREE - The resulting flat device tree
+		     will have a copy of the bd_t.  Space should be
+		     pre-allocated in the dts for the bd_t.
 
 		CONFIG_OF_HAS_UBOOT_ENV
 
-		The resulting flat device tree will have a copy of u-boot's
-		environment variables
+		 * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
+		 * CONFIG_OF_FLAT_TREE - The resulting flat device tree
+		     will have a copy of u-boot's environment variables
 
 		CONFIG_OF_BOARD_SETUP
 
@@ -722,6 +737,8 @@ The following options need to be configured:
 
 		#define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
 
+	Other Commands:
+		fdt (flattened device tree) command: CONFIG_OF_LIBFDT
 
 	Note:	Don't enable the "icache" and "dcache" commands
 		(configuration option CFG_CMD_CACHE) unless you know
@@ -2444,17 +2461,17 @@ configurations; the following names are supported:
 	csb272_config		lwmon_config		sbc8260_config
 	CU824_config		MBX860T_config		sbc8560_33_config
 	DUET_ADS_config		MBX_config		sbc8560_66_config
-	EBONY_config		MPC8260ADS_config	SM850_config
-	ELPT860_config		MPC8540ADS_config	SPD823TS_config
-	ESTEEM192E_config	MPC8540EVAL_config	stxgp3_config
-	ETX094_config		MPC8560ADS_config	SXNI855T_config
-	FADS823_config		NETVIA_config		TQM823L_config
-	FADS850SAR_config	omap1510inn_config	TQM850L_config
-	FADS860T_config		omap1610h2_config	TQM855L_config
-	FPS850L_config		omap1610inn_config	TQM860L_config
-				omap5912osk_config	walnut_config
-				omap2420h4_config	Yukon8220_config
-							ZPC1900_config
+	EBONY_config		mpc7448hpc2_config	SM850_config
+	ELPT860_config		MPC8260ADS_config	SPD823TS_config
+	ESTEEM192E_config	MPC8540ADS_config	stxgp3_config
+	ETX094_config		MPC8540EVAL_config	SXNI855T_config
+	FADS823_config		NMPC8560ADS_config	TQM823L_config
+	FADS850SAR_config	NETVIA_config		TQM850L_config
+	FADS860T_config		omap1510inn_config	TQM855L_config
+	FPS850L_config		omap1610h2_config	TQM860L_config
+				omap1610inn_config	walnut_config
+				omap5912osk_config	Yukon8220_config
+				omap2420h4_config	ZPC1900_config
 
 Note: for some board special configuration names may exist; check if
       additional information is available from the board vendor; for

avr32_config.mk

@@ -21,5 +21,5 @@
 # MA 02111-1307 USA
 #
 
-PLATFORM_RELFLAGS	+= -ffixed-r5 -mno-pic -mrelax
+PLATFORM_RELFLAGS	+= -ffixed-r5 -fPIC -mno-init-got -mrelax
 PLATFORM_LDFLAGS	+= --relax

board/AtmarkTechno/suzaku/suzaku.c

@@ -24,7 +24,7 @@
 
 /* This is a board specific file.  It's OK to include board specific
  * header files */
-#include <asm/suzaku.h>
+#include <config.h>
 
 void do_reset(void)
 {

board/AtmarkTechno/suzaku/u-boot.lds

@@ -61,6 +61,7 @@ SECTIONS
 	{
 		__bss_start = .;
 		*(.bss)
-		__bss_start = .;
+		__bss_end = .;
 	}
+	__end = . ;
 }

board/amcc/acadia/Makefile

@@ -23,25 +23,29 @@
 
 include $(TOPDIR)/config.mk
 
-LIB	= lib$(BOARD).a
+LIB	= $(obj)lib$(BOARD).a
 
-OBJS	= $(BOARD).o cpr.o memory.o
+COBJS	= $(BOARD).o cpr.o memory.o
 SOBJS	=
 
-$(LIB):	$(OBJS) $(SOBJS)
-	$(AR) crv $@ $(OBJS) $(SOBJS)
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
 
 clean:
 	rm -f $(SOBJS) $(OBJS)
 
 distclean:	clean
-	rm -f $(LIB) core *.bak .depend
+	rm -f $(LIB) core *.bak .depend *~
 
 #########################################################################
 
-.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
-		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
 
-sinclude .depend
+sinclude $(obj).depend
 
 #########################################################################

board/amcc/acadia/acadia.c

@@ -26,10 +26,7 @@
 
 extern void board_pll_init_f(void);
 
-/* Some specific Acadia Defines */
-#define CPLD_BASE	0x80000000
-
-void liveoak_gpio_init(void)
+static void acadia_gpio_init(void)
 {
 	/*
 	 * GPIO0 setup (select GPIO or alternate function)
@@ -54,62 +51,16 @@ void liveoak_gpio_init(void)
 	out32(GPIO1_TCR, CFG_GPIO1_TCR);  /* enable output driver for outputs */
 }
 
-#if 0 /* test-only: not called at all??? */
-void ext_bus_cntlr_init(void)
-{
-#if (defined(EBC_PB4AP) && defined(EBC_PB4CR) && !(CFG_INIT_DCACHE_CS == 4))
-       	mtebc(pb4ap, EBC_PB4AP);
-       	mtebc(pb4cr, EBC_PB4CR);
-#endif
-}
-#endif
-
 int board_early_init_f(void)
 {
 	unsigned int reg;
 
-#if 0 /* test-only */
-	/*
-	 * If CRAM memory and SPI/NAND boot, and if the CRAM memory is
-	 * already initialized by the pre-loader then we can't reinitialize
-	 * CPR registers, GPIO registers and EBC registers as this will
-	 * have the effect of un-initializing CRAM.
-	 */
-	spr_reg = (volatile unsigned long) mfspr(SPRG7);
-	if (spr_reg != LOAK_CRAM) { /* != CRAM */
+	/* don't reinit PLL when booting via I2C bootstrap option */
+	mfsdr(SDR_PINSTP, reg);
+	if (reg != 0xf0000000)
 		board_pll_init_f();
-		liveoak_gpio_init();
-		ext_bus_cntlr_init();
 
-		mtebc(pb1ap, CFG_EBC_PB1AP);
-		mtebc(pb1cr, CFG_EBC_PB1CR);
-
-		mtebc(pb2ap, CFG_EBC_PB2AP);
-		mtebc(pb2cr, CFG_EBC_PB2CR);
-	}
-#else
-	board_pll_init_f();
-	liveoak_gpio_init();
-/*	ext_bus_cntlr_init(); */
-#endif
-
-#if 0 /* test-only (orig) */
-	/*
-	 * If we boot from NAND Flash, we are running in
-	 * RAM, so disable the EBC_CS0 so that it goes back
-	 * to the NOR Flash.  It will be enabled later
-	 * for the NAND Flash on EBC_CS1
-	 */
-	mfsdr(sdrultra0, reg);
-	mtsdr(sdrultra0, reg & ~SDR_ULTRA0_CSNSEL0);
-#endif
-#if 0 /* test-only */
-	/* configure for NAND */
-	mfsdr(sdrultra0, reg);
-	reg &= ~SDR_ULTRA0_CSN_MASK;
-	reg |= SDR_ULTRA0_CSNSEL0 >> CFG_NAND_CS;
-	mtsdr(sdrultra0, reg & ~SDR_ULTRA0_CSNSEL0);
-#endif
+	acadia_gpio_init();
 
 	/* USB Host core needs this bit set */
 	mfsdr(sdrultra1, reg);
@@ -128,7 +79,7 @@ int board_early_init_f(void)
 int misc_init_f(void)
 {
 	/* Set EPLD to take PHY out of reset */
-	out8(CPLD_BASE + 0x05, 0x00);
+	out8(CFG_CPLD_BASE + 0x05, 0x00);
 	udelay(100000);
 
 	return 0;

board/amcc/acadia/config.mk

@@ -1,5 +1,5 @@
 #
-# (C) Copyright 2000
+# (C) Copyright 2007
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this
@@ -21,21 +21,10 @@
 # MA 02111-1307 USA
 #
 
-sinclude $(TOPDIR)/board/amcc/liveoak/config.tmp
-
 ifndef TEXT_BASE
 TEXT_BASE = 0xFFFC0000
 endif
 
-ifeq ($(CONFIG_NAND_U_BOOT),y)
-LDSCRIPT = $(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds
-endif
-
-ifeq ($(CONFIG_SPI_U_BOOT),y)
-LDSCRIPT = $(TOPDIR)/board/$(BOARDDIR)/u-boot-spi.lds
-PAD_TO = 0x00840000
-endif
-
 ifeq ($(debug),1)
 PLATFORM_CPPFLAGS += -DDEBUG
 endif

board/amcc/acadia/cpr.c

@@ -76,19 +76,19 @@ void board_pll_init_f(void)
 	 * | UART0 |   28.57    |   7 (0x07)|
 	 * | UART1 |   28.57    |   7 (0x07)|
 	 * | DAC   |   28.57    |   7 (0xA7)|
-	 * | ADC   |    4     	|  50 (0x32)|
+	 * | ADC   |    4       |  50 (0x32)|
 	 * | PWM   |   28.57    |   7 (0x07)|
 	 * | EMAC  |    4       |  50 (0x32)|
 	 * -----------------------------------
 	 */
 
 	/* Initialize PLL */
-	mtcpr(cprpllc,   0x20000238);
-	mtcpr(cprplld,   0x03010400);
+	mtcpr(cprpllc, 0x20000238);
+	mtcpr(cprplld, 0x03010400);
 	mtcpr(cprprimad, 0x03050a0a);
-	mtcpr(cprperc0,  0x00000000);
-	mtcpr(cprperd0,  0x070a0707);	/* SPI clk div. eq. OPB clk div. */
-	mtcpr(cprperd1,  0x07323200);
+	mtcpr(cprperc0, 0x00000000);
+	mtcpr(cprperd0, 0x070a0707);	/* SPI clk div. eq. OPB clk div. */
+	mtcpr(cprperd1, 0x07323200);
 	mtcpr(cprclkupd, 0x40000000);
 }
 
@@ -117,11 +117,11 @@ void board_pll_init_f(void)
 	 */
 
 	/* Initialize PLL */
-	mtcpr(cprpllc,   0x0000033C);
-	mtcpr(cprplld,   0x0a010000);
+	mtcpr(cprpllc, 0x0000033C);
+	mtcpr(cprplld, 0x0a010000);
 	mtcpr(cprprimad, 0x02040808);
-	mtcpr(cprperd0,  0x02080505);	/* SPI clk div. eq. OPB clk div. */
-	mtcpr(cprperd1,  0xA6A60300);
+	mtcpr(cprperd0, 0x02080505);	/* SPI clk div. eq. OPB clk div. */
+	mtcpr(cprperd1, 0xA6A60300);
 	mtcpr(cprclkupd, 0x40000000);
 }
 
@@ -143,20 +143,20 @@ void board_pll_init_f(void)
 	 */
 
 	/* Initialize PLL */
-	mtcpr(cprpllc,   0x000003BC);
-	mtcpr(cprplld,   0x06060600);
+	mtcpr(cprpllc, 0x000003BC);
+	mtcpr(cprplld, 0x06060600);
 	mtcpr(cprprimad, 0x02020004);
-	mtcpr(cprperd0,  0x04002828);	/* SPI clk div. eq. OPB clk div. */
-	mtcpr(cprperd1,  0xC8C81600);
+	mtcpr(cprperd0, 0x04002828);	/* SPI clk div. eq. OPB clk div. */
+	mtcpr(cprperd1, 0xC8C81600);
 	mtcpr(cprclkupd, 0x40000000);
 }
-#endif /* CPU_<speed>_405EZ */
+#endif				/* CPU_<speed>_405EZ */
 
 #if defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL)
 /*
  * Get timebase clock frequency
  */
-unsigned long get_tbclk (void)
+unsigned long get_tbclk(void)
 {
 	unsigned long cpr_plld;
 	unsigned long cpr_primad;
@@ -192,4 +192,4 @@ unsigned long get_tbclk (void)
 
 	return (freqProcessor);
 }
-#endif	/* defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL) */
+#endif /* defined(CONFIG_NAND_SPL) || defined(CONFIG_SPI_SPL) */

board/amcc/acadia/flash.c

@@ -1,1108 +0,0 @@
-/*
- * (C) Copyright 2004-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2002 Jun Gu <jung@artesyncp.com>
- * Add support for Am29F016D and dynamic switch setting.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * Modified 4/5/2001
- * Wait for completion of each sector erase command issued
- * 4/5/2001
- * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
- */
-
-#include <common.h>
-#include <ppc4xx.h>
-#include <asm/processor.h>
-
-#ifdef DEBUG
-#define DEBUGF(x...) printf(x)
-#else
-#define DEBUGF(x...)
-#endif				/* DEBUG */
-
-flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips */
-
-/*
- * Mark big flash bank (16 bit instead of 8 bit access) in address with bit 0
- */
-static unsigned long flash_addr_table[][CFG_MAX_FLASH_BANKS] = {
-	{0xffc00001}, /* 0:boot from big flash */
-};
-
-/*
- * include common flash code (for amcc boards)
- */
-/*-----------------------------------------------------------------------
- * Functions
- */
-static int write_word(flash_info_t * info, ulong dest, ulong data);
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-static int write_word_1(flash_info_t * info, ulong dest, ulong data);
-static int write_word_2(flash_info_t * info, ulong dest, ulong data);
-static int flash_erase_1(flash_info_t * info, int s_first, int s_last);
-static int flash_erase_2(flash_info_t * info, int s_first, int s_last);
-static ulong flash_get_size_1(vu_long * addr, flash_info_t * info);
-static ulong flash_get_size_2(vu_long * addr, flash_info_t * info);
-#endif
-
-void flash_print_info(flash_info_t * info)
-{
-	int i;
-	int k;
-	int size;
-	int erased;
-	volatile unsigned long *flash;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:
-		printf("AMD ");
-		break;
-	case FLASH_MAN_STM:
-		printf("STM ");
-		break;
-	case FLASH_MAN_FUJ:
-		printf("FUJITSU ");
-		break;
-	case FLASH_MAN_SST:
-		printf("SST ");
-		break;
-	case FLASH_MAN_MX:
-		printf("MIXC ");
-		break;
-	default:
-		printf("Unknown Vendor ");
-		break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AM040:
-		printf("AM29F040 (512 Kbit, uniform sector size)\n");
-		break;
-	case FLASH_AM400B:
-		printf("AM29LV400B (4 Mbit, bottom boot sect)\n");
-		break;
-	case FLASH_AM400T:
-		printf("AM29LV400T (4 Mbit, top boot sector)\n");
-		break;
-	case FLASH_AM800B:
-		printf("AM29LV800B (8 Mbit, bottom boot sect)\n");
-		break;
-	case FLASH_AM800T:
-		printf("AM29LV800T (8 Mbit, top boot sector)\n");
-		break;
-	case FLASH_AMD016:
-		printf("AM29F016D (16 Mbit, uniform sector size)\n");
-		break;
-	case FLASH_AM160B:
-		printf("AM29LV160B (16 Mbit, bottom boot sect)\n");
-		break;
-	case FLASH_AM160T:
-		printf("AM29LV160T (16 Mbit, top boot sector)\n");
-		break;
-	case FLASH_AM320B:
-		printf("AM29LV320B (32 Mbit, bottom boot sect)\n");
-		break;
-	case FLASH_AM320T:
-		printf("AM29LV320T (32 Mbit, top boot sector)\n");
-		break;
-	case FLASH_AM033C:
-		printf("AM29LV033C (32 Mbit, top boot sector)\n");
-		break;
-	case FLASH_SST800A:
-		printf("SST39LF/VF800 (8 Mbit, uniform sector size)\n");
-		break;
-	case FLASH_SST160A:
-		printf("SST39LF/VF160 (16 Mbit, uniform sector size)\n");
-		break;
-	case FLASH_STMW320DT:
-		printf ("M29W320DT (32 M, top sector)\n");
-		break;
-	case FLASH_MXLV320T:
-		printf ("MXLV320T (32 Mbit, top sector)\n");
-		break;
-	default:
-		printf("Unknown Chip Type\n");
-		break;
-	}
-
-	printf("  Size: %ld KB in %d Sectors\n",
-	       info->size >> 10, info->sector_count);
-
-	printf("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; ++i) {
-		/*
-		 * Check if whole sector is erased
-		 */
-		if (i != (info->sector_count - 1))
-			size = info->start[i + 1] - info->start[i];
-		else
-			size = info->start[0] + info->size - info->start[i];
-		erased = 1;
-		flash = (volatile unsigned long *)info->start[i];
-		size = size >> 2;	/* divide by 4 for longword access */
-		for (k = 0; k < size; k++) {
-			if (*flash++ != 0xffffffff) {
-				erased = 0;
-				break;
-			}
-		}
-
-		if ((i % 5) == 0)
-			printf("\n   ");
-		printf(" %08lX%s%s",
-		       info->start[i],
-		       erased ? " E" : "  ", info->protect[i] ? "RO " : "   ");
-	}
-	printf("\n");
-	return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-static ulong flash_get_size(vu_long * addr, flash_info_t * info)
-{
-	/* bit 0 used for big flash marking */
-	if ((ulong)addr & 0x1) {
-		return flash_get_size_2((vu_long *)((ulong)addr & 0xfffffffe), info);
-	} else {
-		return flash_get_size_1(addr, info);
-	}
-}
-
-static ulong flash_get_size_1(vu_long * addr, flash_info_t * info)
-#else
-static ulong flash_get_size(vu_long * addr, flash_info_t * info)
-#endif
-{
-	short i;
-	CFG_FLASH_WORD_SIZE value;
-	ulong base = (ulong) addr;
-	volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr;
-
-	DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr);
-
-	/* Write auto select command: read Manufacturer ID */
-	addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-	addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-	addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00900090;
-	udelay(1000);
-
-	value = addr2[0];
-	DEBUGF("FLASH MANUFACT: %x\n", value);
-
-	switch (value) {
-	case (CFG_FLASH_WORD_SIZE) AMD_MANUFACT:
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-	case (CFG_FLASH_WORD_SIZE) FUJ_MANUFACT:
-		info->flash_id = FLASH_MAN_FUJ;
-		break;
-	case (CFG_FLASH_WORD_SIZE) SST_MANUFACT:
-		info->flash_id = FLASH_MAN_SST;
-		break;
-	case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
-		info->flash_id = FLASH_MAN_STM;
-		break;
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);	/* no or unknown flash  */
-	}
-
-	value = addr2[1];	/* device ID            */
-	DEBUGF("\nFLASH DEVICEID: %x\n", value);
-
-	switch (value) {
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV040B:
-		info->flash_id += FLASH_AM040;
-		info->sector_count = 8;
-		info->size = 0x0080000;	/* => 512 ko */
-		break;
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_F040B:
-		info->flash_id += FLASH_AM040;
-		info->sector_count = 8;
-		info->size = 0x0080000;	/* => 512 ko */
-		break;
-
-	case (CFG_FLASH_WORD_SIZE) STM_ID_M29W040B:
-		info->flash_id += FLASH_AM040;
-		info->sector_count = 8;
-		info->size = 0x0080000;	/* => 512 ko */
-		break;
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_F016D:
-		info->flash_id += FLASH_AMD016;
-		info->sector_count = 32;
-		info->size = 0x00200000;
-		break;		/* => 2 MB              */
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV033C:
-		info->flash_id += FLASH_AMDLV033C;
-		info->sector_count = 64;
-		info->size = 0x00400000;
-		break;		/* => 4 MB              */
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400T:
-		info->flash_id += FLASH_AM400T;
-		info->sector_count = 11;
-		info->size = 0x00080000;
-		break;		/* => 0.5 MB            */
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400B:
-		info->flash_id += FLASH_AM400B;
-		info->sector_count = 11;
-		info->size = 0x00080000;
-		break;		/* => 0.5 MB            */
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800T:
-		info->flash_id += FLASH_AM800T;
-		info->sector_count = 19;
-		info->size = 0x00100000;
-		break;		/* => 1 MB              */
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800B:
-		info->flash_id += FLASH_AM800B;
-		info->sector_count = 19;
-		info->size = 0x00100000;
-		break;		/* => 1 MB              */
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160T:
-		info->flash_id += FLASH_AM160T;
-		info->sector_count = 35;
-		info->size = 0x00200000;
-		break;		/* => 2 MB              */
-
-	case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160B:
-		info->flash_id += FLASH_AM160B;
-		info->sector_count = 35;
-		info->size = 0x00200000;
-		break;		/* => 2 MB              */
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);	/* => no or unknown flash */
-	}
-
-	/* set up sector start address table */
-	if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) {
-		for (i = 0; i < info->sector_count; i++)
-			info->start[i] = base + (i * 0x00010000);
-	} else {
-		if (info->flash_id & FLASH_BTYPE) {
-			/* set sector offsets for bottom boot block type        */
-			info->start[0] = base + 0x00000000;
-			info->start[1] = base + 0x00004000;
-			info->start[2] = base + 0x00006000;
-			info->start[3] = base + 0x00008000;
-			for (i = 4; i < info->sector_count; i++) {
-				info->start[i] =
-				    base + (i * 0x00010000) - 0x00030000;
-			}
-		} else {
-			/* set sector offsets for top boot block type           */
-			i = info->sector_count - 1;
-			info->start[i--] = base + info->size - 0x00004000;
-			info->start[i--] = base + info->size - 0x00006000;
-			info->start[i--] = base + info->size - 0x00008000;
-			for (; i >= 0; i--) {
-				info->start[i] = base + i * 0x00010000;
-			}
-		}
-	}
-
-	/* check for protected sectors */
-	for (i = 0; i < info->sector_count; i++) {
-		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
-		/* D0 = 1 if protected */
-		addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]);
-
-		/* For AMD29033C flash we need to resend the command of *
-		 * reading flash protection for upper 8 Mb of flash     */
-		if (i == 32) {
-			addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA;
-			addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555;
-			addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090;
-		}
-
-		if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
-			info->protect[i] = 0;
-		else
-			info->protect[i] = addr2[2] & 1;
-	}
-
-	/* issue bank reset to return to read mode */
-	addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
-
-	return (info->size);
-}
-
-static int wait_for_DQ7_1(flash_info_t * info, int sect)
-{
-	ulong start, now, last;
-	volatile CFG_FLASH_WORD_SIZE *addr =
-	    (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
-	start = get_timer(0);
-	last = start;
-	while ((addr[0] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
-	       (CFG_FLASH_WORD_SIZE) 0x00800080) {
-		if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-			printf("Timeout\n");
-			return -1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 1000) {	/* every second */
-			putc('.');
-			last = now;
-		}
-	}
-	return 0;
-}
-
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-int flash_erase(flash_info_t * info, int s_first, int s_last)
-{
-	if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T)) {
-		return flash_erase_2(info, s_first, s_last);
-	} else {
-		return flash_erase_1(info, s_first, s_last);
-	}
-}
-
-static int flash_erase_1(flash_info_t * info, int s_first, int s_last)
-#else
-int flash_erase(flash_info_t * info, int s_first, int s_last)
-#endif
-{
-	volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
-	volatile CFG_FLASH_WORD_SIZE *addr2;
-	int flag, prot, sect, l_sect;
-	int i;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf("- missing\n");
-		} else {
-			printf("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf("Can't erase unknown flash type - aborted\n");
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf("- Warning: %d protected sectors will not be erased!\n",
-		       prot);
-	} else {
-		printf("\n");
-	}
-
-	l_sect = -1;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
-			if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00500050;	/* block erase */
-				for (i = 0; i < 50; i++)
-					udelay(1000);	/* wait 1 ms */
-			} else {
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00300030;	/* sector erase */
-			}
-			l_sect = sect;
-			/*
-			 * Wait for each sector to complete, it's more
-			 * reliable.  According to AMD Spec, you must
-			 * issue all erase commands within a specified
-			 * timeout.  This has been seen to fail, especially
-			 * if printf()s are included (for debug)!!
-			 */
-			wait_for_DQ7_1(info, sect);
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay(1000);
-
-	/* reset to read mode */
-	addr = (CFG_FLASH_WORD_SIZE *) info->start[0];
-	addr[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;	/* reset bank */
-
-	printf(" done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i = 0, cp = wp; i < l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-		for (; i < 4 && cnt > 0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt == 0 && i < 4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i = 0; i < 4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i < 4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *) cp);
-	}
-
-	return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-static int write_word(flash_info_t * info, ulong dest, ulong data)
-{
-	if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T)) {
-		return write_word_2(info, dest, data);
-	} else {
-		return write_word_1(info, dest, data);
-	}
-}
-
-static int write_word_1(flash_info_t * info, ulong dest, ulong data)
-#else
-static int write_word(flash_info_t * info, ulong dest, ulong data)
-#endif
-{
-	volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
-	volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest;
-	volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data;
-	ulong start;
-	int i;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*((vu_long *)dest) & data) != data) {
-		return (2);
-	}
-
-	for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) {
-		int flag;
-
-		/* Disable interrupts which might cause a timeout here */
-		flag = disable_interrupts();
-
-		addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-		addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-		addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00A000A0;
-
-		dest2[i] = data2[i];
-
-		/* re-enable interrupts if necessary */
-		if (flag)
-			enable_interrupts();
-
-		/* data polling for D7 */
-		start = get_timer(0);
-		while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
-		       (data2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080)) {
-
-			if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-				return (1);
-			}
-		}
-	}
-
-	return (0);
-}
-
-#ifdef CFG_FLASH_2ND_16BIT_DEV
-
-#undef  CFG_FLASH_WORD_SIZE
-#define CFG_FLASH_WORD_SIZE unsigned short
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size_2(vu_long * addr, flash_info_t * info)
-{
-	short i;
-	int n;
-	CFG_FLASH_WORD_SIZE value;
-	ulong base = (ulong) addr;
-	volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr;
-
-	DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr);
-
-	/* issue bank reset to return to read mode */
-	addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
-	/* Write auto select command: read Manufacturer ID */
-	addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-	addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-	addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00900090;
-	udelay(1000);
-
-	value = addr2[0];
-	DEBUGF("FLASH MANUFACT: %x\n", value);
-
-#if 0 /* TODO: remove ifdef when Flash responds correctly */
-	switch (value) {
-	case (CFG_FLASH_WORD_SIZE) AMD_MANUFACT:
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-	case (CFG_FLASH_WORD_SIZE) FUJ_MANUFACT:
-		info->flash_id = FLASH_MAN_FUJ;
-		break;
-	case (CFG_FLASH_WORD_SIZE) SST_MANUFACT:
-		info->flash_id = FLASH_MAN_SST;
-		break;
-	case (CFG_FLASH_WORD_SIZE) STM_MANUFACT:
-		info->flash_id = FLASH_MAN_STM;
-		break;
-	case (CFG_FLASH_WORD_SIZE) MX_MANUFACT:
-		info->flash_id = FLASH_MAN_MX;
-		break;
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);	/* no or unknown flash  */
-	}
-#endif /* TODO: remove ifdef when Flash responds correctly */
-
-	/*
-	 * TODO: Start
-	 * 	 uncomment block above when Flash responds correctly.
-	 *	 also remove the lines below:
-	 */
-	info->flash_id = FLASH_MAN_AMD;
-	DEBUGF("FLASH MANUFACT: FLASH_MAN_AMD\n");
-	/* TODO: End */
-
-	value = addr2[1];	/* device ID            */
-
-	DEBUGF("\nFLASH DEVICEID: %x\n", value);
-
-#if 0 /* TODO: remove ifdef when Flash responds correctly */
-	switch (value) {
-
-	case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320T:
-		info->flash_id += FLASH_AM320T;
-		info->sector_count = 71;
-		info->size = 0x00400000;  break;	/* => 4 MB	*/
-
-	case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320B:
-		info->flash_id += FLASH_AM320B;
-		info->sector_count = 71;
-		info->size = 0x00400000;  break;	/* => 4 MB	*/
-
-	case (CFG_FLASH_WORD_SIZE)STM_ID_29W320DT:
-		info->flash_id += FLASH_STMW320DT;
-		info->sector_count = 67;
-		info->size = 0x00400000;  break;	/* => 4 MB	*/
-
-	case (CFG_FLASH_WORD_SIZE)MX_ID_LV320T:
-		info->flash_id += FLASH_MXLV320T;
-		info->sector_count = 71;
-		info->size = 0x00400000;  break;	/* => 4 MB	*/
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);	/* => no or unknown flash */
-	}
-#endif /* TODO: remove ifdef when Flash responds correctly */
-
-	/*
-	 * TODO: Start
-	 * 	 uncomment block above when Flash responds correctly.
-	 *	 also remove the lines below:
-	 */
-	DEBUGF("\nFLASH DEVICEID: FLASH_AM320T\n");
-	info->flash_id += FLASH_AM320T;
-	info->sector_count = 71;
-	info->size = 0x00400000;  /* => 4 MB	*/
-	/* TODO: End */
-
-	/* set up sector start address table */
-	if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
-	    ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) {
-		for (i = 0; i < info->sector_count; i++)
-			info->start[i] = base + (i * 0x00010000);
-	} else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT) {
-		/* set sector offsets for top boot block type		*/
-		base += info->size;
-		i = info->sector_count;
-		/*  1 x 16k boot sector */
-		base -= 16 << 10;
-		--i;
-		info->start[i] = base;
-		/*  2 x 8k  boot sectors */
-		for (n=0; n<2; ++n) {
-			base -= 8 << 10;
-			--i;
-			info->start[i] = base;
-		}
-		/*  1 x 32k boot sector */
-		base -= 32 << 10;
-		--i;
-		info->start[i] = base;
-
-		while (i > 0) {			/* 64k regular sectors	*/
-			base -= 64 << 10;
-			--i;
-			info->start[i] = base;
-		}
-	} else if ( ((info->flash_id & FLASH_TYPEMASK) == FLASH_MXLV320T) ||
-		    ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) ) {
-		i = info->sector_count - 1;
-		info->start[i--] = base + info->size - 0x00002000;
-		info->start[i--] = base + info->size - 0x00004000;
-		info->start[i--] = base + info->size - 0x00006000;
-		info->start[i--] = base + info->size - 0x00008000;
-		info->start[i--] = base + info->size - 0x0000a000;
-		info->start[i--] = base + info->size - 0x0000c000;
-		info->start[i--] = base + info->size - 0x0000e000;
-		info->start[i--] = base + info->size - 0x00010000;
-		for (; i >= 0; i--) {
-			info->start[i] = base + i * 0x00010000;
-		}
-	}
-	else {
-		if (info->flash_id & FLASH_BTYPE){
-			/* set sector offsets for bottom boot block type */
-			info->start[0] = base + 0x00000000;
-			info->start[1] = base + 0x00004000;
-			info->start[2] = base + 0x00006000;
-			info->start[3] = base + 0x00008000;
-			for (i = 4; i < info->sector_count; i++) {
-				info->start[i] =
-				    base + (i * 0x00010000) - 0x00030000;
-			}
-		} else {
-			/* set sector offsets for top boot block type */
-			i = info->sector_count - 1;
-			info->start[i--] = base + info->size - 0x00004000;
-			info->start[i--] = base + info->size - 0x00006000;
-			info->start[i--] = base + info->size - 0x00008000;
-			for (; i >= 0; i--) {
-				info->start[i] = base + i * 0x00010000;
-			}
-		}
-	}
-
-	/* check for protected sectors */
-	for (i = 0; i < info->sector_count; i++) {
-		/* read sector protection at sector address,(A7 .. A0) = 0x02 */
-		/* D0 = 1 if protected */
-		addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]);
-
-		/* For AMD29033C flash we need to resend the command of *
-		 * reading flash protection for upper 8 Mb of flash     */
-		if (i == 32) {
-			addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA;
-			addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555;
-			addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090;
-		}
-
-		if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
-			info->protect[i] = 0;
-		else
-			info->protect[i] = addr2[2] & 1;
-	}
-
-	/* issue bank reset to return to read mode */
-	addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;
-
-	return (info->size);
-}
-
-/*
- * TODO: FIX: this wait loop sometimes fails: DQ7 indicates the erase command
- *		never was accepted (i.e. didn't start) - why????
- */
-static int wait_for_DQ7_2(flash_info_t * info, int sect)
-{
-	ulong start, now, last, counter = 0;
-	volatile CFG_FLASH_WORD_SIZE *addr =
-	    (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
-	start = get_timer(0);
-	DEBUGF("DQ7_2: start = 0x%08lx\n", start);
-	last = start;
-	while ((addr[0] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
-	       (CFG_FLASH_WORD_SIZE) 0x00800080) {
-		DEBUGF("DQ7_2: start = 0x%08lx, now = 0x%08lx\n", start, now);
-		if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-			printf("Timeout\n");
-			return -1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 1000) {	/* every second */
-			putc('.');
-			last = now;
-		}
-		udelay(1000000); /* 1 sec */
-		putc('.');
-		counter++;
-		if (counter > 5)  {
-			return -1;
-		}
-		DEBUGF("DQ7_2: now = 0x%08lx, last = 0x%08lx\n", now, last);
-	}
-	return 0;
-}
-
-static void wr_flash_cmd(ulong sector, ushort addr, CFG_FLASH_WORD_SIZE value)
-{
-	int fw_size;
-
-	fw_size = sizeof(value);
-	switch (fw_size)
-	{
-	case 1:
-		out8((ulong)(sector + addr), value);
-		break;
-	case 2:
-		out16((ulong)(sector + (addr << 1)), value);
-		break;
-	default:
-		printf("flash_erase: error incorrect chip programing size.\n");
-	}
-	return;
-}
-
-static int flash_erase_2(flash_info_t * info, int s_first, int s_last)
-{
-	volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
-	volatile CFG_FLASH_WORD_SIZE *addr2;
-	int flag, prot, sect, l_sect, count = 0;
-	int i;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf("- missing\n");
-		} else {
-			printf("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf("Can't erase unknown flash type - aborted\n");
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf("- Warning: %d protected sectors will not be erased!\n",
-		       prot);
-	} else {
-		printf("\n");
-	}
-
-	l_sect = -1;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first, count = 0; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
-
-			if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00500050;	/* block erase */
-				for (i = 0; i < 50; i++)
-					udelay(1000);	/* wait 1 ms */
-			} else {
-				/*
-				 * TODO: fix code
-				 */
-				wr_flash_cmd((ulong)addr, 0, (CFG_FLASH_WORD_SIZE) 0x00F000F0);
-				wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR0, (CFG_FLASH_WORD_SIZE) 0x00AA00AA);
-				wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR1, (CFG_FLASH_WORD_SIZE) 0x00550055);
-				wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR0, (CFG_FLASH_WORD_SIZE) 0x00800080);
-				wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR0, (CFG_FLASH_WORD_SIZE) 0x00AA00AA);
-				wr_flash_cmd((ulong)addr, CFG_FLASH_ADDR1, (CFG_FLASH_WORD_SIZE) 0x00550055);
-				wr_flash_cmd((ulong)addr2, 0, (CFG_FLASH_WORD_SIZE) 0x00300030);
-				udelay(2000000);	/* 2 sec */
-				wr_flash_cmd((ulong)addr, 0, (CFG_FLASH_WORD_SIZE) 0x00F000F0);
-
-#if 0
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080;
-				addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-				addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00300030;	/* sector erase */
-#endif
-			}
-			l_sect = sect;
-			printf("..");
-			printf("..");
-			/*
-			 * Wait for each sector to complete, it's more
-			 * reliable.  According to AMD Spec, you must
-			 * issue all erase commands within a specified
-			 * timeout.  This has been seen to fail, especially
-			 * if printf()s are included (for debug)!!
-			 */
-			wait_for_DQ7_2(info, sect);
-			count++;
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay(1000);
-
-	/* reset to read mode */
-	addr = (CFG_FLASH_WORD_SIZE *) info->start[0];
-	addr[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0;	/* reset bank */
-
-	printf(" done\n");
-
-	if (count > 0) {
-		return 0;
-	} else {
-		return 1;
-	}
-}
-
-static int write_word_2(flash_info_t * info, ulong dest, ulong data)
-{
-	volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
-	volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest;
-	volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data;
-	ulong start;
-	int i;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*((vu_long *)dest) & data) != data) {
-		return (2);
-	}
-
-	for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) {
-		int flag;
-
-		/* Disable interrupts which might cause a timeout here */
-		flag = disable_interrupts();
-
-		addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA;
-		addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055;
-		addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00A000A0;
-
-		dest2[i] = data2[i];
-
-		/* re-enable interrupts if necessary */
-		if (flag)
-			enable_interrupts();
-
-		/* data polling for D7 */
-		start = get_timer(0);
-		while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080) !=
-		       (data2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080)) {
-
-			if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-				return (1);
-			}
-		}
-	}
-
-	return (0);
-}
-#endif /* CFG_FLASH_2ND_16BIT_DEV */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(vu_long * addr, flash_info_t * info);
-static int write_word(flash_info_t * info, ulong dest, ulong data);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init(void)
-{
-	unsigned long total_b = 0;
-	unsigned long size_b[CFG_MAX_FLASH_BANKS];
-	unsigned short index = 0;
-	int i;
-
-	index = 0;
-
-	DEBUGF("\n");
-	DEBUGF("FLASH: Index: %d\n", index);
-
-	/* Init: no FLASHes known */
-	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-		flash_info[i].sector_count = -1;
-		flash_info[i].size = 0;
-
-		/* check whether the address is 0 */
-		if (flash_addr_table[index][i] == 0) {
-			continue;
-		}
-
-		/* call flash_get_size() to initialize sector address */
-		size_b[i] = flash_get_size((vu_long *) flash_addr_table[index][i],
-				   &flash_info[i]);
-		flash_info[i].size = size_b[i];
-		if (flash_info[i].flash_id == FLASH_UNKNOWN) {
-			printf("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
-			       i, size_b[i], size_b[i] << 20);
-			flash_info[i].sector_count = -1;
-			flash_info[i].size = 0;
-		}
-
-		/* Monitor protection ON by default */
-		(void)flash_protect(FLAG_PROTECT_SET, CFG_MONITOR_BASE,
-				    CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
-				    &flash_info[i]);
-#if defined(CFG_ENV_IS_IN_FLASH)
-		(void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR,
-				    CFG_ENV_ADDR + CFG_ENV_SECT_SIZE - 1,
-				    &flash_info[i]);
-#if defined(CFG_ENV_IS_IN_FLASH) && defined(CFG_ENV_ADDR_REDUND)
-		(void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR_REDUND,
-				    CFG_ENV_ADDR_REDUND + CFG_ENV_SECT_SIZE - 1,
-				    &flash_info[i]);
-#endif
-#endif
-
-		total_b += flash_info[i].size;
-	}
-
-	return total_b;
-}

board/amcc/acadia/memory.c

@@ -21,529 +21,80 @@
  * MA 02111-1307 USA
  */
 
+/* define DEBUG for debugging output (obviously ;-)) */
+#if 0
+#define DEBUG
+#endif
+
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
 
-#define CRAM_BANK0_BASE 		0x0
-#define CRAM_DIDR			0x00100000
-#define	MICRON_MT45W8MW16BGX_CRAM_ID	0x1b431b43
-#define	MICRON_MT45W8MW16BGX_CRAM_ID2	0x13431343
-#define	MICRON_DIDR_VENDOR_ID		0x00030003	/* 00011b */
-#define	CRAM_DIDR_VENDOR_ID_MASK	0x001f001f	/* DIDR[4:0] */
-#define	CRAM_DEVID_NOT_SUPPORTED	0x00000000
-
-#define PSRAM_PASS	0x50415353	/* "PASS" */
-#define PSRAM_FAIL	0x4641494C	/* "FAIL" */
-
-static u32 is_cram_inited(void);
-static u32 is_cram(void);
-static long int cram_init(u32);
-static void cram_bcr_write(u32);
-void udelay (unsigned long);
-
+/*
+ * sdram_init - Dummy implementation for start.S, spd_sdram used on this board!
+ */
 void sdram_init(void)
 {
-	volatile unsigned long spr_reg;
-
-	/*
-	 * If CRAM not initialized or CRAM looks initialized because this
-	 * is after a warm reboot then set SPRG7 to indicate CRAM needs
-	 * initialization.  Note that CRAM is initialized by the SPI and
-	 * NAND preloader.
-	 */
-	spr_reg = (volatile unsigned long) mfspr(SPRG6);
-	if ((is_cram_inited() != 1) || (spr_reg != LOAK_SPL)) {
-		mtspr(SPRG7, LOAK_NONE);	/* "NONE" */
-	}
-#if 1
-	/*
-	 * When running the NAND SPL, the normal EBC configuration is not
-	 * done, so We need to enable EPLD access on EBC_CS_2 and the memory
-	 * on EBC_CS_3
-	 */
-
-	/* Enable CPLD - Needed for PSRAM Access */
-
-
-	/* Init SDRAM by setting EBC Bank 3 for PSRAM */
-	mtebc(pb1ap, CFG_EBC_PB1AP);
-	mtebc(pb1cr, CFG_EBC_PB1CR);
-
-	mtebc(pb2ap, CFG_EBC_PB2AP);
-	mtebc(pb2cr, CFG_EBC_PB2CR);
-
-	/* pre-boot loader code: we are in OCM */
-	mtspr(SPRG6, LOAK_SPL);	/* "SPL " */
-	mtspr(SPRG7, LOAK_OCM);	/* "OCM " */
-#endif
 	return;
 }
 
 static void cram_bcr_write(u32 wr_val)
 {
-	u32 tmp_reg;
-	u32 val;
-	volatile u32 gpio_reg;
-
-	/* # Program CRAM write */
-
-	/*
-	 * set CRAM_CRE = 0x1
-	 * set wr_val = wr_val << 2
-	 */
-	gpio_reg = in32(GPIO1_OR);
-	out32(GPIO1_OR,  gpio_reg | 0x00000400);
-	wr_val = wr_val << 2;
-	/* wr_val = 0x1c048; */
+	wr_val <<= 2;
 
-	/*
-	 * # stop PLL clock before programming CRAM
-	 * set EPLD0_MUX_CTL.OESPR3 = 1
-	 * delay 2
-	 */
+	/* set CRAM_CRE to 1 */
+	gpio_write_bit(CFG_GPIO_CRAM_CRE, 1);
 
-	/*
-	 * # CS1
-	 * read 0x00200000
-	 * #shift 2 bit left before write
-	 * set val = wr_val + 0x00200000
-	 * write dmem val 0
-	 * read 0x00200000 val
-	 * print val/8x
-	 */
-	tmp_reg = in32(0x00200000);
-	val = wr_val + 0x00200000;
-	/* val = 0x0021c048; */
-	out32(val, 0x0000);
-	udelay(100000);
-	val = in32(0x00200000);
+	/* Write BCR to CRAM on CS1 */
+	out32(wr_val + 0x00200000, 0);
+	debug("CRAM VAL: %08x for CS1 ", wr_val + 0x00200000);
 
-	debug("CRAM VAL: %x for CS1 ", val);
+	/* Write BCR to CRAM on CS2 */
+	out32(wr_val + 0x02200000, 0);
+	debug("CRAM VAL: %08x for CS2\n", wr_val + 0x02200000);
 
-	/*
-	 * # CS2
-	 * read 0x02200000
-	 * #shift 2 bit left before write
-	 * set val = wr_val + 0x02200000
-	 * write dmem val 0
-	 * read 0x02200000 val
-	 * print val/8x
-	 */
-	tmp_reg = in32(0x02200000);
-	val = wr_val + 0x02200000;
-	/* val = 0x0221c048; */
-	out32(val, 0x0000);
-	udelay(100000);
-	val = in32(0x02200000);
+	sync();
+	eieio();
 
-	debug("CRAM VAL: %x for CS2 ", val);
+	/* set CRAM_CRE back to 0 (normal operation) */
+	gpio_write_bit(CFG_GPIO_CRAM_CRE, 0);
 
-	/*
-	 * # Start PLL clock before programming CRAM
-	 * set EPLD0_MUX_CTL.OESPR3 = 0
-	 */
-
-	/*
-	 * set CRAMCR = 0x1
-	 */
-	gpio_reg = in32(GPIO1_OR);
-	out32(GPIO1_OR,  gpio_reg | 0x00000400);
-
-	/*
-	 * # read CRAM config BCR ( bit19:18 = 10b )
-	 * #read 0x00200000
-	 * # 1001_1001_0001_1111 ( 991f ) =>
-	 * #10_0110_0100_0111_1100  =>   2647c => 0022647c
-	 * #0011_0010_0011_1110 (323e)
-	 * #
-	 */
-
-	/*
-	 * set EPLD0_MUX_CTL.CRAMCR = 0x0
-	 */
-	gpio_reg = in32(GPIO1_OR);
-	out32(GPIO1_OR,  gpio_reg & 0xFFFFFBFF);
 	return;
 }
 
-static u32 is_cram_inited()
-{
-	volatile unsigned long spr_reg;
-
-	/*
- 	 * If CRAM is initialized already, then don't reinitialize it again.
-	 * In the case of NAND boot and SPI boot, CRAM will already be
-	 * initialized by the pre-loader
-	 */
-	spr_reg = (volatile unsigned long) mfspr(SPRG7);
-	if (spr_reg == LOAK_CRAM) {
-		return 1;
-	} else {
-		return 0;
-	}
-}
-
-/******
- * return 0 if not CRAM
- * return 1 if CRAM and it's already inited by preloader
- * else return cram_id (CRAM Device Identification Register)
- ******/
-static u32 is_cram(void)
-{
-	u32 gpio_TCR, gpio_OSRL, gpio_OR, gpio_ISR1L;
-	volatile u32 gpio_reg;
-	volatile u32 cram_id = 0;
-
-	if (is_cram_inited() == 1) {
-		/* this is CRAM and it is already inited (by preloader) */
-		cram_id = 1;
-	} else {
-		/*
-		 * # CRAM CLOCK
-		 * set GPIO0_TCR.G8 = 1
-		 * set GPIO0_OSRL.G8 = 0
-		 * set GPIO0_OR.G8 = 0
-		 */
-		gpio_reg = in32(GPIO0_TCR);
-		gpio_TCR = gpio_reg;
-		out32(GPIO0_TCR, gpio_reg | 0x00800000);
-		gpio_reg = in32(GPIO0_OSRL);
-		gpio_OSRL = gpio_reg;
-		out32(GPIO0_OSRL, gpio_reg & 0xffffbfff);
-		gpio_reg = in32(GPIO0_OR);
-		gpio_OR = gpio_reg;
-		out32(GPIO0_OR, gpio_reg & 0xff7fffff);
-
-		/*
-		 * # CRAM Addreaa Valid
-		 * set GPIO0_TCR.G10 = 1
-		 * set GPIO0_OSRL.G10 = 0
-		 * set GPIO0_OR.G10 = 0
-		 */
-		gpio_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, gpio_reg | 0x00200000);
-		gpio_reg = in32(GPIO0_OSRL);
-		out32(GPIO0_OSRL, gpio_reg & 0xfffffbff);
-		gpio_reg = in32(GPIO0_OR);
-		out32(GPIO0_OR, gpio_reg & 0xffdfffff);
-
-		/*
-		 * # config input (EBC_WAIT)
-		 * set GPIO0_ISR1L.G9 = 1
-		 * set GPIO0_TCR.G9 = 0
-		 */
-		gpio_reg = in32(GPIO0_ISR1L);
-		gpio_ISR1L = gpio_reg;
-		out32(GPIO0_ISR1L, gpio_reg | 0x00001000);
-		gpio_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, gpio_reg & 0xffbfffff);
-
-		/*
-		 * Enable CRE to read Registers
-		 * set GPIO0_TCR.21 = 1
-		 * set GPIO1_OR.21 = 1
-		 */
-		gpio_reg = in32(GPIO1_TCR);
-		out32(GPIO1_TCR, gpio_reg | 0x00000400);
-
-		gpio_reg = in32(GPIO1_OR);
-		out32(GPIO1_OR,  gpio_reg | 0x00000400);
-
-		/* Read Version ID */
-		cram_id = (volatile u32) in32(CRAM_BANK0_BASE+CRAM_DIDR);
-		udelay(100000);
-
-		asm volatile("	sync");
-		asm volatile("	eieio");
-
-		debug("Cram ID: %X ", cram_id);
-
-		switch (cram_id) {
-		case MICRON_MT45W8MW16BGX_CRAM_ID:
-		case MICRON_MT45W8MW16BGX_CRAM_ID2:
-			/* supported CRAM vendor/part */
-			break;
-		case CRAM_DEVID_NOT_SUPPORTED:
-		default:
-			/* check for DIDR Vendor ID of Micron */
-			if ((cram_id & CRAM_DIDR_VENDOR_ID_MASK) ==
-						MICRON_DIDR_VENDOR_ID)
-			{
-				/* supported CRAM vendor */
-				break;
-			}
-			/* this is not CRAM or not supported CRAM vendor/part */
-			cram_id = 0;
-			/*
-			 * reset the GPIO registers to the values that were
-			 * there before this routine
-			 */
-			out32(GPIO0_TCR, gpio_TCR);
-			out32(GPIO0_OSRL, gpio_OSRL);
-			out32(GPIO0_OR, gpio_OR);
-			out32(GPIO0_ISR1L, gpio_ISR1L);
-			break;
-		}
-	}
-
-	return cram_id;
-}
-
-static long int cram_init(u32 already_inited)
-{
-	volatile u32 tmp_reg;
-	u32 cram_wr_val;
-
-	if (already_inited == 0) return 0;
-
-	/*
-	 * If CRAM is initialized already, then don't reinitialize it again.
-	 * In the case of NAND boot and SPI boot, CRAM will already be
-	 * initialized by the pre-loader
-	 */
-	if (already_inited != 1) {
-		/*
-		 * #o CRAM Card
-		 * #  - CRAMCRE @reg16 = 1; for CRAM to use
-		 * #  - CRAMCRE @reg16 = 0; for CRAM to program
-		 *
-		 * # enable CRAM SEL, move from setEPLD.cmd
-		 * set EPLD0_MUX_CTL.OECRAM = 0
-		 * set EPLD0_MUX_CTL.CRAMCR = 1
-		 * set EPLD0_ETHRSTBOOT.SLCRAM = 0
-		 * #end
-		 */
-
-		/*
-		 * #1. EBC need to program READY, CLK, ADV for ASync mode
-		 * # config output
-		 */
-
-		/*
-		 * # CRAM CLOCK
-		 * set GPIO0_TCR.G8 = 1
-		 * set GPIO0_OSRL.G8 = 0
-		 * set GPIO0_OR.G8 = 0
-		 */
-		tmp_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, tmp_reg | 0x00800000);
-		tmp_reg = in32(GPIO0_OSRL);
-		out32(GPIO0_OSRL, tmp_reg & 0xffffbfff);
-		tmp_reg = in32(GPIO0_OR);
-		out32(GPIO0_OR, tmp_reg & 0xff7fffff);
-
-		/*
-		 * # CRAM Addreaa Valid
-		 * set GPIO0_TCR.G10 = 1
-		 * set GPIO0_OSRL.G10 = 0
-		 * set GPIO0_OR.G10 = 0
-		 */
-		tmp_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, tmp_reg | 0x00200000);
-		tmp_reg = in32(GPIO0_OSRL);
-		out32(GPIO0_OSRL, tmp_reg & 0xfffffbff);
-		tmp_reg = in32(GPIO0_OR);
-		out32(GPIO0_OR, tmp_reg & 0xffdfffff);
-
-		/*
-		 * # config input (EBC_WAIT)
-		 * set GPIO0_ISR1L.G9 = 1
-		 * set GPIO0_TCR.G9 = 0
-		 */
-		tmp_reg = in32(GPIO0_ISR1L);
-		out32(GPIO0_ISR1L, tmp_reg | 0x00001000);
-		tmp_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, tmp_reg & 0xffbfffff);
-
-		/*
-		 * # config CS4 from GPIO
-		 * set GPIO0_TCR.G0 = 1
-		 * set GPIO0_OSRL.G0 = 1
-		 */
-		tmp_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, tmp_reg | 0x80000000);
-		tmp_reg = in32(GPIO0_OSRL);
-		out32(GPIO0_OSRL, tmp_reg | 0x40000000);
-
-		/*
-		 * #2. EBC in Async mode
-		 * # set EBC0_PB1AP = 0x078f0ec0
-		 * set EBC0_PB1AP = 0x078f1ec0
-		 * set EBC0_PB2AP = 0x078f1ec0
-		 */
-		mtebc(pb1ap, 0x078F1EC0);
-		mtebc(pb2ap, 0x078F1EC0);
-
-		/*
-		 * #set EBC0_PB1CR = 0x000bc000
-		 * #enable CS2 for CRAM
-		 * set EBC0_PB2CR = 0x020bc000
-		 */
-		mtebc(pb1cr, 0x000BC000);
-		mtebc(pb2cr, 0x020BC000);
-
-		/*
-		 * #3. set CRAM in Sync mode
-		 * #exec cm_bcr_write.cmd { 0x701f }
-		 * #3. set CRAM in Sync mode (full drv strength)
-		 * exec cm_bcr_write.cmd { 0x701F }
-		 */
-		cram_wr_val = 0x7012;	/* CRAM burst setting */
-		cram_bcr_write(cram_wr_val);
-
-		/*
-		 * #4. EBC in Sync mode
-		 * #set EBC0_PB1AP = 0x9f800fc0
-		 * #set EBC0_PB1AP = 0x900001c0
-		 * set EBC0_PB2AP = 0x9C0201c0
-		 * set EBC0_PB2AP = 0x9C0201c0
-		 */
-		mtebc(pb1ap, 0x9C0201C0);
-		mtebc(pb2ap, 0x9C0201C0);
-
-		/*
-		 * #5. EBC need to program READY, CLK, ADV for Sync mode
-		 * # config output
-		 * set GPIO0_TCR.G8 = 1
-		 * set GPIO0_OSRL.G8 = 1
-		 * set GPIO0_TCR.G10 = 1
-		 * set GPIO0_OSRL.G10 = 1
-		 */
-		tmp_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, tmp_reg | 0x00800000);
-		tmp_reg = in32(GPIO0_OSRL);
-		out32(GPIO0_OSRL, tmp_reg | 0x00004000);
-		tmp_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, tmp_reg | 0x00200000);
-		tmp_reg = in32(GPIO0_OSRL);
-		out32(GPIO0_OSRL, tmp_reg | 0x00000400);
-
-		/*
-		 * # config input
-		 * set GPIO0_ISR1L.G9 = 1
-		 * set GPIO0_TCR.G9 = 0
-		 */
-		tmp_reg = in32(GPIO0_ISR1L);
-		out32(GPIO0_ISR1L, tmp_reg | 0x00001000);
-		tmp_reg = in32(GPIO0_TCR);
-		out32(GPIO0_TCR, tmp_reg & 0xffbfffff);
-
-		/*
-		 * # config EBC to use RDY
-		 * set SDR0_ULTRA0.EBCREN = 1
-		 */
-		mfsdr(sdrultra0, tmp_reg);
-		mtsdr(sdrultra0, tmp_reg | 0x04000000);
-
-		/*
-		 * set EPLD0_MUX_CTL.OESPR3 = 0
-		 */
-		mtspr(SPRG7, LOAK_CRAM);	/* "CRAM" */
-	} /* if (already_inited != 1) */
-
-	return (64 * 1024 * 1024);
-}
-
-/******
- * return 0 if not PSRAM
- * return 1 if is PSRAM
- ******/
-static int is_psram(u32 addr)
-{
-	u32 test_pattern = 0xdeadbeef;
-	volatile u32 readback;
-
-	if (addr == CFG_SDRAM_BASE) {
-		/* This is to temp enable OE for PSRAM */
-		out16(EPLD_BASE+EPLD_MUXOE, 0x7f0f);
-		udelay(10000);
-	}
-
-	out32(addr, test_pattern);
-	asm volatile("	sync");
-	asm volatile("	eieio");
-
-	readback = (volatile u32) in32(addr);
-	asm volatile("	sync");
-	asm volatile("	eieio");
-	if (readback == test_pattern) {
-		return 1;
-	} else {
-		return 0;
-	}
-}
-
-static long int psram_init(void)
+long int initdram(int board_type)
 {
-	u32 readback;
-	long psramsize = 0;
-	int i;
-
-	/* This is to temp enable OE for PSRAM */
-	out16(EPLD_BASE+EPLD_MUXOE, 0x7f0f);
-	udelay(10000);
+	u32 val;
 
-	/*
-	 * PSRAM bank 1: read then write to address 0x00000000
-	 */
-	for (i = 0; i < 100; i++) {
-		if (is_psram(CFG_SDRAM_BASE + (i*256)) == 1) {
-			readback = PSRAM_PASS;
-		} else {
-			readback = PSRAM_FAIL;
-			break;
-		}
-	}
-	if (readback == PSRAM_PASS) {
-		debug("psram_init(bank0): pass\n");
-		psramsize = (16 * 1024 * 1024);
-	} else {
-		debug("psram_init(bank0): fail\n");
-		return 0;
-	}
+	/* 1. EBC need to program READY, CLK, ADV for ASync mode */
+	gpio_config(CFG_GPIO_CRAM_CLK, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
+	gpio_config(CFG_GPIO_CRAM_ADV, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
+	gpio_config(CFG_GPIO_CRAM_CRE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
+	gpio_config(CFG_GPIO_CRAM_WAIT, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG);
 
-#if 0
-	/*
-	 * PSRAM bank 1: read then write to address 0x01000000
-	 */
-	for (i = 0; i < 100; i++) {
-		if (is_psram((1 << 24) + (i*256)) == 1) {
-			readback = PSRAM_PASS;
-		} else {
-			readback = PSRAM_FAIL;
-			break;
-		}
-	}
-	if (readback == PSRAM_PASS) {
-		debug("psram_init(bank1): pass\n");
-		psramsize = psramsize + (16 * 1024 * 1024);
-	}
-#endif
+	/* 2. EBC in Async mode */
+	mtebc(pb1ap, 0x078F1EC0);
+	mtebc(pb2ap, 0x078F1EC0);
+	mtebc(pb1cr, 0x000BC000);
+	mtebc(pb2cr, 0x020BC000);
 
-	mtspr(SPRG7, LOAK_PSRAM);	/* "PSRA" - PSRAM */
+	/* 3. Set CRAM in Sync mode */
+	cram_bcr_write(0x7012);		/* CRAM burst setting */
 
-	return psramsize;
-}
+	/* 4. EBC in Sync mode */
+	mtebc(pb1ap, 0x9C0201C0);
+	mtebc(pb2ap, 0x9C0201C0);
 
-long int initdram(int board_type)
-{
-	long int sram_size;
-	u32 cram_inited;
+	/* Set GPIO pins back to alternate function */
+	gpio_config(CFG_GPIO_CRAM_CLK, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
+	gpio_config(CFG_GPIO_CRAM_ADV, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
 
-	/* Determine Attached Memory Expansion Card*/
-	cram_inited = is_cram();
-	if (cram_inited != 0) {					/* CRAM */
-		debug("CRAM Expansion Card attached\n");
-		sram_size = cram_init(cram_inited);
-	} else if (is_psram(CFG_SDRAM_BASE+4) == 1) {		/* PSRAM */
-		debug("PSRAM Expansion Card attached\n");
-		sram_size = psram_init();
-	} else { 						/* no SRAM */
-		debug("No Memory Card Attached!!\n");
-		sram_size = 0;
-	}
+	/* Config EBC to use RDY */
+	mfsdr(sdrultra0, val);
+	mtsdr(sdrultra0, val | 0x04000000);
 
-	return sram_size;
+	return (CFG_MBYTES_RAM << 20);
 }
 
 int testdram(void)

board/amcc/acadia/u-boot.lds

@@ -62,19 +62,6 @@ SECTIONS
     /* the sector layout of our flash chips!	XXX FIXME XXX	*/
 
     cpu/ppc4xx/start.o	(.text)
-    cpu/ppc4xx/kgdb.o	(.text)
-    cpu/ppc4xx/traps.o	(.text)
-    cpu/ppc4xx/interrupts.o	(.text)
-    cpu/ppc4xx/serial.o	(.text)
-    cpu/ppc4xx/cpu_init.o	(.text)
-    cpu/ppc4xx/speed.o	(.text)
-    common/dlmalloc.o	(.text)
-    lib_generic/crc32.o		(.text)
-    lib_ppc/extable.o	(.text)
-    lib_generic/zlib.o		(.text)
-
-/*    . = env_offset;*/
-/*    common/environment.o(.text)*/
 
     *(.text)
     *(.fixup)

board/amcc/bamboo/bamboo.c

@@ -23,6 +23,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/gpio.h>
 #include <spd_sdram.h>
 #include <ppc440.h>
 #include "bamboo.h"

board/amcc/bamboo/bamboo.h

@@ -264,19 +264,9 @@
 #define TRUE 1
 #define FALSE 0
 
-#define GPIO_GROUP_MAX	    2
-#define GPIO_MAX	    32
-#define GPIO_ALT1_SEL	    0x40000000	    /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 0 */
-#define GPIO_ALT2_SEL	    0x80000000	    /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 1 */
-#define GPIO_ALT3_SEL	    0xC0000000	    /* GPIO_OUT value put in GPIO_TSx for the GPIO nb 2 */
-#define GPIO_MASK	    0xC0000000	    /* GPIO_MASK */
-#define GPIO_IN_SEL	    0x40000000	    /* GPIO_IN value put in GPIO_ISx for the GPIO nb 0 */
-					    /* For the other GPIO number, you must shift */
-
 #define GPIO0		0
 #define GPIO1		1
 
-
 /*#define MAX_SELECTION_NB	CORE_NB */
 #define MAX_CORE_SELECT_NB	22
 

board/amcc/katmai/cmd_katmai.c

@@ -27,6 +27,9 @@
 #include <i2c.h>
 #include <asm/byteorder.h>
 
+#define	CONFIG_STRESS		/* enable 667 MHz CPU freq selection */
+#define DEBUG
+
 static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
 	uchar	chip;
@@ -49,55 +52,28 @@ static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	else
 		chip = IIC0_ALT_BOOTPROM_ADDR;
 
-	do {
-		printf("enter sys clock frequency 33 or 66 Mhz or quit to abort\n");
-		nbytes = readline (" ? ");
-
-		if (strcmp(console_buffer, "quit") == 0)
-			return 0;
-
-		if ((strcmp(console_buffer, "33") != 0) &
-		    (strcmp(console_buffer, "66") != 0))
-			nbytes=0;
-
-		strcpy(sysClock, console_buffer);
-
-	} while (nbytes == 0);
+	/* on Katmai SysClk is always 33MHz */
+	strcpy(sysClock, "33");
 
 	do {
-		if (strcmp(sysClock, "66") == 0) {
-			printf("enter cpu clock frequency 400, 533 Mhz or quit to abort\n");
-		} else {
 #ifdef	CONFIG_STRESS
-			printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
+		printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
 #else
-			printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
+		printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
 #endif
-		}
 		nbytes = readline (" ? ");
 
 		if (strcmp(console_buffer, "quit") == 0)
 			return 0;
 
-		if (strcmp(sysClock, "66") == 0) {
-			if ((strcmp(console_buffer, "400") != 0) &
-			    (strcmp(console_buffer, "533") != 0)
-#ifdef	CONFIG_STRESS
-			    & (strcmp(console_buffer, "667") != 0)
-#endif
-				) {
-				nbytes = 0;
-			}
-		} else {
-			if ((strcmp(console_buffer, "400") != 0) &
-			    (strcmp(console_buffer, "500") != 0) &
-			    (strcmp(console_buffer, "533") != 0)
+		if ((strcmp(console_buffer, "400") != 0) &&
+		    (strcmp(console_buffer, "500") != 0) &&
+		    (strcmp(console_buffer, "533") != 0)
 #ifdef	CONFIG_STRESS
-			    & (strcmp(console_buffer, "667") != 0)
+		    && (strcmp(console_buffer, "667") != 0)
 #endif
-				) {
-				nbytes = 0;
-			}
+			) {
+			nbytes = 0;
 		}
 
 		strcpy(cpuClock, console_buffer);
@@ -124,13 +100,13 @@ static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 				return 0;
 
 			if (strcmp(cpuClock, "400") == 0) {
-				if ((strcmp(console_buffer, "100") != 0) &
+				if ((strcmp(console_buffer, "100") != 0) &&
 				    (strcmp(console_buffer, "133") != 0))
 					nbytes = 0;
 			}
 #ifdef	CONFIG_STRESS
 			if (strcmp(cpuClock, "667") == 0) {
-				if ((strcmp(console_buffer, "133") != 0) &
+				if ((strcmp(console_buffer, "133") != 0) &&
 				    (strcmp(console_buffer, "166") != 0))
 					nbytes = 0;
 			}
@@ -147,9 +123,9 @@ static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		if (strcmp(console_buffer, "quit") == 0)
 			return 0;
 
-		if ((strcmp(console_buffer, "33") != 0) &
-		    (strcmp(console_buffer, "66") != 0) &
-		    (strcmp(console_buffer, "100") != 0) &
+		if ((strcmp(console_buffer, "33") != 0) &&
+		    (strcmp(console_buffer, "66") != 0) &&
+		    (strcmp(console_buffer, "100") != 0) &&
 		    (strcmp(console_buffer, "133") != 0)) {
 			nbytes = 0;
 		}
@@ -176,11 +152,11 @@ static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	} while (nbytes == 0);
 
 	if (strcmp(sysClock, "33") == 0) {
-		if ((strcmp(cpuClock, "400") == 0) &
+		if ((strcmp(cpuClock, "400") == 0) &&
 		    (strcmp(plbClock, "100") == 0))
 			data = 0x8678c206;
 
-		if ((strcmp(cpuClock, "400") == 0) &
+		if ((strcmp(cpuClock, "400") == 0) &&
 		    (strcmp(plbClock, "133") == 0))
 			data = 0x8678c2c6;
 
@@ -189,42 +165,16 @@ static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 		if ((strcmp(cpuClock, "533") == 0))
 			data = 0x87790252;
-
 #ifdef	CONFIG_STRESS
-		if ((strcmp(cpuClock, "667") == 0) &
+		if ((strcmp(cpuClock, "667") == 0) &&
 		    (strcmp(plbClock, "133") == 0))
 			data = 0x87794256;
 
-		if ((strcmp(cpuClock, "667") == 0) &
+		if ((strcmp(cpuClock, "667") == 0) &&
 		    (strcmp(plbClock, "166") == 0))
 			data = 0x87794206;
-
-#endif
-	}
-	if (strcmp(sysClock, "66") == 0) {
-		if ((strcmp(cpuClock, "400") == 0) &
-		    (strcmp(plbClock, "100") == 0))
-			data = 0x84706206;
-
-		if ((strcmp(cpuClock, "400") == 0) &
-		    (strcmp(plbClock, "133") == 0))
-			data = 0x847062c6;
-
-		if ((strcmp(cpuClock, "533") == 0))
-			data = 0x85708206;
-
-#ifdef	CONFIG_STRESS
-		if ((strcmp(cpuClock, "667") == 0) &
-		    (strcmp(plbClock, "133") == 0))
-			data = 0x8570a256;
-
-		if ((strcmp(cpuClock, "667") == 0) &
-		    (strcmp(plbClock, "166") == 0))
-			data = 0x8570a206;
-
 #endif
 	}
-
 #ifdef	DEBUG
 	printf(" pin strap0 to write in i2c  = %x\n", data);
 #endif	/* DEBUG */
@@ -233,19 +183,20 @@ static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		printf("Error writing strap0 in %s\n", argv[2]);
 
 	if (strcmp(pcixClock, "33") == 0)
-		data = 0x00000701;
+		data = 0x000007E1;
 
 	if (strcmp(pcixClock, "66") == 0)
-		data = 0x00000601;
+		data = 0x000006E1;
 
 	if (strcmp(pcixClock, "100") == 0)
-		data = 0x00000501;
+		data = 0x000005E1;
 
 	if (strcmp(pcixClock, "133") == 0)
-		data = 0x00000401;
+		data = 0x000004E1;
 
 	if (strcmp(plbClock, "166") == 0)
-		data |= 0x05950000;
+/*		data |= 0x05950000; */	/* this set's DDR2 clock == PLB clock */
+		data |= 0x05A50000;	/* this set's DDR2 clock == 2 * PLB clock */
 	else
 		data |= 0x05A50000;
 

board/amcc/katmai/init.S

@@ -103,7 +103,7 @@ tlbtabB:
 
 	tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
 
-	tlbentry(CFG_ACE_BASE, SZ_1K, 0xE0000000, 4,AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_ACE_BASE, SZ_1K, CFG_ACE_BASE, 4,AC_R|AC_W|SA_G|SA_I)
 
 	tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
 	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)

board/amcc/katmai/katmai.c

@@ -27,6 +27,7 @@
 #include <asm/processor.h>
 #include <i2c.h>
 #include <asm-ppc/io.h>
+#include <asm-ppc/gpio.h>
 
 #include "../cpu/ppc4xx/440spe_pcie.h"
 

board/amcc/sequoia/sequoia.c

@@ -363,8 +363,8 @@ int checkboard(void)
 	printf("Board: Rainier - AMCC PPC440GRx Evaluation Board");
 #endif
 
-	rev = *(u8 *)(CFG_CPLD + 0);
-	val = *(u8 *)(CFG_CPLD + 5) & 0x01;
+	rev = *(u8 *)(CFG_BCSR_BASE + 0);
+	val = *(u8 *)(CFG_BCSR_BASE + 5) & 0x01;
 	printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33);
 
 	if (s != NULL) {

board/atmel/atstk1000/Makefile

@@ -26,7 +26,7 @@ include $(TOPDIR)/config.mk
 
 LIB	:= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o flash.o
+COBJS	:= $(BOARD).o flash.o eth.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))

board/atmel/atstk1000/atstk1000.c

@@ -23,6 +23,8 @@
 
 #include <asm/io.h>
 #include <asm/sdram.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/hmatrix2.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -40,9 +42,27 @@ static const struct sdram_info sdram = {
 	.txsr		= 5,
 };
 
-void board_init_memories(void)
+int board_early_init_f(void)
 {
-	gd->sdram_size = sdram_init(&sdram);
+	/* Set the SDRAM_ENABLE bit in the HEBI SFR */
+	hmatrix2_writel(SFR4, 1 << 1);
+
+	gpio_enable_ebi();
+	gpio_enable_usart1();
+#if defined(CONFIG_MACB)
+	gpio_enable_macb0();
+	gpio_enable_macb1();
+#endif
+#if defined(CONFIG_MMC)
+	gpio_enable_mmci();
+#endif
+
+	return 0;
+}
+
+long int initdram(int board_type)
+{
+	return sdram_init(&sdram);
 }
 
 void board_init_info(void)

cpu/at32ap/at32ap7000/hebi.c → board/atmel/atstk1000/eth.c

@@ -1,5 +1,7 @@
 /*
- * Copyright (C) 2006 Atmel Corporation
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * Ethernet initialization for the ATSTK1000 starterkit
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -21,18 +23,16 @@
  */
 #include <common.h>
 
-#include <asm/io.h>
-
-#include <asm/arch/hmatrix2.h>
 #include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
 
-void cpu_enable_sdram(void)
-{
-	const struct device *hmatrix;
+extern int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
 
-	hmatrix = get_device(DEVICE_HMATRIX);
+#if defined(CONFIG_MACB) && (CONFIG_COMMANDS & CFG_CMD_NET)
+void atstk1000_eth_initialize(bd_t *bi)
+{
+	int id = 0;
 
-	/* Set the SDRAM_ENABLE bit in the HEBI SFR */
-	hmatrix2_writel(hmatrix, SFR4, 1 << 1);
+	macb_eth_initialize(id++, (void *)MACB0_BASE, bi->bi_phy_id[0]);
+	macb_eth_initialize(id++, (void *)MACB1_BASE, bi->bi_phy_id[1]);
 }
+#endif

board/atmel/atstk1000/flash.c

@@ -57,7 +57,7 @@ unsigned long flash_init(void)
 
 	gd->bd->bi_flashstart = CFG_FLASH_BASE;
 	gd->bd->bi_flashsize = CFG_FLASH_SIZE;
-	gd->bd->bi_flashoffset = __edata_lma - _text;
+	gd->bd->bi_flashoffset = _edata - _text;
 
 	flash_info[0].size = CFG_FLASH_SIZE;
 	flash_info[0].sector_count = 135;

board/atmel/atstk1000/u-boot.lds

@@ -40,35 +40,38 @@ SECTIONS
 	}
 	. = ALIGN(32);
 	__flashprog_end = .;
+	_etext = .;
 
-	. = ALIGN(8);
 	.rodata : {
 		*(.rodata)
 		*(.rodata.*)
 	}
-	_etext = .;
 
-	__data_lma = ALIGN(8);
-	. = 0x24000000;
+	. = ALIGN(8);
 	_data = .;
-	.data : AT(__data_lma) {
+	.data : {
 		*(.data)
 		*(.data.*)
 	}
 
 	. = ALIGN(4);
 	__u_boot_cmd_start = .;
-	__u_boot_cmd_lma = __data_lma + (__u_boot_cmd_start - _data);
-	.u_boot_cmd : AT(__u_boot_cmd_lma) {
+	.u_boot_cmd : {
 		KEEP(*(.u_boot_cmd))
 	}
 	__u_boot_cmd_end = .;
 
+	. = ALIGN(4);
+	_got = .;
+	.got : {
+		*(.got)
+	}
+	_egot = .;
+
 	. = ALIGN(8);
 	_edata = .;
-	__edata_lma = __u_boot_cmd_lma + (_edata - __u_boot_cmd_start);
 
-	.bss : AT(__edata_lma) {
+	.bss : {
 		*(.bss)
 		*(.bss.*)
 	}

board/bf533-ezkit/Makefile

@@ -1,7 +1,7 @@
 #
 # U-boot - Makefile
 #
-# Copyright (c) 2007 Analog Device Inc.
+# Copyright (c) 2005-2007 Analog Device Inc.
 #
 # (C) Copyright 2000-2006
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.

board/bf533-ezkit/bf533-ezkit.c

@@ -1,7 +1,7 @@
 /*
  * U-boot - ezkit533.c
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #include <common.h>

board/bf533-ezkit/flash-defines.h

@@ -1,7 +1,7 @@
 /*
  * U-boot - flash-defines.h
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #ifndef __FLASHDEFINES_H__
@@ -60,7 +60,7 @@ void reset_flash(void);
 int erase_flash(void);
 int erase_block_flash(int, unsigned long);
 void unlock_flash(long lOffset);
-int write_data(long lStart, long lCount, long lStride, int *pnData);
+int write_data(long lStart, long lCount, uchar *pnData);
 int FillData(long lStart, long lCount, long lStride, int *pnData);
 int read_data(long lStart, long lCount, long lStride, int *pnData);
 int read_flash(long nOffset, int *pnValue);

board/bf533-ezkit/flash.c

@@ -1,7 +1,7 @@
 /*
  * U-boot - flash.c Flash driver for PSD4256GV
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  * This file is based on BF533EzFlash.c originally written by Analog Devices, Inc.
  *
  * (C) Copyright 2000-2004
@@ -22,8 +22,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #include <asm/io.h>
@@ -178,63 +178,66 @@ int flash_erase(flash_info_t * info, int s_first, int s_last)
 int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
 {
 	int ret;
-
-	ret = write_data(addr, cnt, 1, (int *)src);
+	int d;
+	if (addr % 2) {
+		read_flash(addr - 1 - CFG_FLASH_BASE, &d);
+		d = (int)((d & 0x00FF) | (*src++ << 8));
+		ret = write_data(addr - 1, 2, (uchar *) & d);
+		if (ret == FLASH_FAIL)
+			return ERR_NOT_ERASED;
+		ret = write_data(addr + 1, cnt - 1, src);
+	} else
+		ret = write_data(addr, cnt, src);
 	if (ret == FLASH_FAIL)
 		return ERR_NOT_ERASED;
 	return FLASH_SUCCESS;
 }
 
-int write_data(long lStart, long lCount, long lStride, int *pnData)
+int write_data(long lStart, long lCount, uchar * pnData)
 {
 	long i = 0;
-	int j = 0;
 	unsigned long ulOffset = lStart - CFG_FLASH_BASE;
 	int d;
-	int iShift = 0;
-	int iNumWords = 2;
-	int nLeftover = lCount % 4;
 	int nSector = 0;
+	int flag = 0;
 
-	for (i = 0; (i < lCount / 4) && (i < BUFFER_SIZE); i++) {
-		for (iShift = 0, j = 0; (j < iNumWords);
-		     j++, ulOffset += (lStride * 2)) {
-			if ((ulOffset >= INVALIDLOCNSTART)
-			    && (ulOffset < INVALIDLOCNEND)) {
-				printf
-				    ("Invalid locations, Try writing to another location \n");
-				return FLASH_FAIL;
-			}
-			get_sector_number(ulOffset, &nSector);
-			read_flash(ulOffset, &d);
-			if (d != 0xffff) {
-				printf
-				    ("Flash not erased at offset 0x%x Please erase to reprogram \n",
-				     ulOffset);
-				return FLASH_FAIL;
-			}
-			unlock_flash(ulOffset);
-			if (write_flash(ulOffset, (pnData[i] >> iShift)) < 0) {
-				printf("Error programming the flash \n");
-				return FLASH_FAIL;
-			}
-			iShift += 16;
-		}
+	if (lCount % 2) {
+		flag = 1;
+		lCount = lCount - 1;
 	}
-	if (nLeftover > 0) {
-		if ((ulOffset >= INVALIDLOCNSTART)
-		    && (ulOffset < INVALIDLOCNEND))
+
+	for (i = 0; i < lCount - 1; i += 2, ulOffset += 2) {
+		get_sector_number(ulOffset, &nSector);
+		read_flash(ulOffset, &d);
+		if (d != 0xffff) {
+			printf
+			    ("Flash not erased at offset 0x%x Please erase to reprogram \n",
+			     ulOffset);
 			return FLASH_FAIL;
+		}
+		unlock_flash(ulOffset);
+		d = (int)(pnData[i] | pnData[i + 1] << 8);
+		write_flash(ulOffset, d);
+		if (poll_toggle_bit(ulOffset) < 0) {
+			printf("Error programming the flash \n");
+			return FLASH_FAIL;
+		}
+		if ((i > 0) && (!(i % AFP_SectorSize2)))
+			printf(".");
+	}
+	if (flag) {
 		get_sector_number(ulOffset, &nSector);
 		read_flash(ulOffset, &d);
 		if (d != 0xffff) {
 			printf
-			    ("Flash already programmed. Please erase to reprogram \n");
-			printf("uloffset = 0x%x \t d = 0x%x\n", ulOffset, d);
+			    ("Flash not erased at offset 0x%x Please erase to reprogram \n",
+			     ulOffset);
 			return FLASH_FAIL;
 		}
 		unlock_flash(ulOffset);
-		if (write_flash(ulOffset, pnData[i]) < 0) {
+		d = (int)(pnData[i] | (d & 0xFF00));
+		write_flash(ulOffset, d);
+		if (poll_toggle_bit(ulOffset) < 0) {
 			printf("Error programming the flash \n");
 			return FLASH_FAIL;
 		}

board/bf533-ezkit/psd4256.h

@@ -1,7 +1,7 @@
 /*
  * U-boot - psd4256.h
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 /*

board/bf533-stamp/Makefile

@@ -1,7 +1,7 @@
 #
 # U-boot - Makefile
 #
-# Copyright (c) 2007 Analog Device Inc.
+# Copyright (c) 2005-2007 Analog Device Inc.
 #
 # (C) Copyright 2000-2006
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.

board/bf533-stamp/bf533-stamp.c

@@ -1,7 +1,7 @@
 /*
  * U-boot - stamp.c STAMP board specific routines
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #include <common.h>

board/bf533-stamp/bf533-stamp.h

@@ -1,7 +1,7 @@
 /*
  * U-boot - stamp.h
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #ifndef __STAMP_H__

board/bf537-stamp/bf537-stamp.c

@@ -1,7 +1,7 @@
 /*
  * U-boot - BF537.c
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #include <common.h>

board/bf537-stamp/flash-defines.h

@@ -1,7 +1,7 @@
 /*
  * U-boot - flash-defines.h
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -21,8 +21,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #ifndef __FLASHDEFINES_H__

board/bf537-stamp/flash.c

@@ -1,7 +1,7 @@
 /*
  * U-boot - flash.c Flash driver for PSD4256GV
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  * This file is based on BF533EzFlash.c originally written by Analog Devices, Inc.
  *
  * (C) Copyright 2000-2004
@@ -22,8 +22,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #include <malloc.h>

board/bf561-ezkit/bf561-ezkit.c

@@ -2,7 +2,7 @@
  * U-boot - ezkit561.c
  *
  * Copyright (c) 2005 Bas Vermeulen <bas@buyways.nl>
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * (C) Copyright 2000-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -22,8 +22,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #include <common.h>

board/mpc8641hpcn/pixis.c → board/freescale/common/pixis.c

@@ -23,14 +23,25 @@
  */
 
 #include <common.h>
-#include <watchdog.h>
 #include <command.h>
+#include <watchdog.h>
 #include <asm/cache.h>
-#include <mpc86xx.h>
 
 #include "pixis.h"
 
 
+static ulong strfractoint(uchar *strptr);
+
+
+/*
+ * Simple board reset.
+ */
+void pixis_reset(void)
+{
+    out8(PIXIS_BASE + PIXIS_RST, 0);
+}
+
+
 /*
  * Per table 27, page 58 of MPC8641HPCN spec.
  */
@@ -235,7 +246,8 @@ void set_px_go_with_watchdog(void)
 }
 
 
-int disable_watchdog(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int pixis_disable_watchdog_cmd(cmd_tbl_t *cmdtp,
+			       int flag, int argc, char *argv[])
 {
 	u8 tmp;
 
@@ -252,7 +264,7 @@ int disable_watchdog(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 }
 
 U_BOOT_CMD(
-	   diswd, 1, 0, disable_watchdog,
+	   diswd, 1, 0, pixis_disable_watchdog_cmd,
 	   "diswd	- Disable watchdog timer \n",
 	   NULL);
 
@@ -263,7 +275,7 @@ U_BOOT_CMD(
  * input: strptr i.e. argv[2]
  */
 
-ulong strfractoint(uchar *strptr)
+static ulong strfractoint(uchar *strptr)
 {
 	int i, j, retval;
 	int mulconst;
@@ -319,3 +331,142 @@ ulong strfractoint(uchar *strptr)
 
 	return retval;
 }
+
+
+int
+pixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	ulong val;
+	ulong corepll;
+
+	/*
+	 * No args is a simple reset request.
+	 */
+	if (argc <= 1) {
+		pixis_reset();
+		/* not reached */
+	}
+
+	if (strcmp(argv[1], "cf") == 0) {
+
+		/*
+		 * Reset with frequency changed:
+		 *    cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+		 */
+		if (argc < 5) {
+			puts(cmdtp->usage);
+			return 1;
+		}
+
+		read_from_px_regs(0);
+
+		val = set_px_sysclk(simple_strtoul(argv[2], NULL, 10));
+
+		corepll = strfractoint(argv[3]);
+		val = val + set_px_corepll(corepll);
+		val = val + set_px_mpxpll(simple_strtoul(argv[4], NULL, 10));
+		if (val == 3) {
+			puts("Setting registers VCFGEN0 and VCTL\n");
+			read_from_px_regs(1);
+			puts("Resetting board with values from ");
+			puts("VSPEED0, VSPEED1, VCLKH, and VCLKL \n");
+			set_px_go();
+		} else {
+			puts(cmdtp->usage);
+			return 1;
+		}
+
+		while (1) ;	/* Not reached */
+
+	} else if (strcmp(argv[1], "altbank") == 0) {
+
+		/*
+		 * Reset using alternate flash bank:
+		 */
+		if (argv[2] == 0) {
+			/*
+			 * Reset from alternate bank without changing
+			 * frequency and without watchdog timer enabled.
+			 *	altbank
+			 */
+			read_from_px_regs(0);
+			read_from_px_regs_altbank(0);
+			if (argc > 2) {
+				puts(cmdtp->usage);
+				return 1;
+			}
+			puts("Setting registers VCFGNE1, VBOOT, and VCTL\n");
+			set_altbank();
+			read_from_px_regs_altbank(1);
+			puts("Resetting board to boot from the other bank.\n");
+			set_px_go();
+
+		} else if (strcmp(argv[2], "cf") == 0) {
+			/*
+			 * Reset with frequency changed
+			 *    altbank cf <SYSCLK freq> <COREPLL ratio>
+			 *				<MPXPLL ratio>
+			 */
+			read_from_px_regs(0);
+			read_from_px_regs_altbank(0);
+			val = set_px_sysclk(simple_strtoul(argv[3], NULL, 10));
+			corepll = strfractoint(argv[4]);
+			val = val + set_px_corepll(corepll);
+			val = val + set_px_mpxpll(simple_strtoul(argv[5],
+								 NULL, 10));
+			if (val == 3) {
+				puts("Setting registers VCFGEN0, VCFGEN1, VBOOT, and VCTL\n");
+				set_altbank();
+				read_from_px_regs(1);
+				read_from_px_regs_altbank(1);
+				puts("Enabling watchdog timer on the FPGA\n");
+				puts("Resetting board with values from ");
+				puts("VSPEED0, VSPEED1, VCLKH and VCLKL ");
+				puts("to boot from the other bank.\n");
+				set_px_go_with_watchdog();
+			} else {
+				puts(cmdtp->usage);
+				return 1;
+			}
+
+			while (1) ;	/* Not reached */
+
+		} else if (strcmp(argv[2], "wd") == 0) {
+			/*
+			 * Reset from alternate bank without changing
+			 * frequencies but with watchdog timer enabled:
+			 *    altbank wd
+			 */
+			read_from_px_regs(0);
+			read_from_px_regs_altbank(0);
+			puts("Setting registers VCFGEN1, VBOOT, and VCTL\n");
+			set_altbank();
+			read_from_px_regs_altbank(1);
+			puts("Enabling watchdog timer on the FPGA\n");
+			puts("Resetting board to boot from the other bank.\n");
+			set_px_go_with_watchdog();
+			while (1) ;	/* Not reached */
+
+		} else {
+			puts(cmdtp->usage);
+			return 1;
+		}
+
+	} else {
+		puts(cmdtp->usage);
+		return 1;
+	}
+
+	return 0;
+}
+
+
+U_BOOT_CMD(
+	pixis_reset, CFG_MAXARGS, 1, pixis_reset_cmd,
+	"pixis_reset - Reset the board using the FPGA sequencer\n",
+	"    pixis_reset\n"
+	"    pixis_reset [altbank]\n"
+	"    pixis_reset altbank wd\n"
+	"    pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>\n"
+	"    pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>\n"
+	);

board/mpc8641hpcn/pixis.h → board/freescale/common/pixis.h

@@ -20,6 +20,7 @@
  * MA 02111-1307 USA
  */
 
+extern void pixis_reset(void);
 extern int set_px_sysclk(ulong sysclk);
 extern int set_px_mpxpll(ulong mpxpll);
 extern int set_px_corepll(ulong corepll);
@@ -28,6 +29,3 @@ extern void read_from_px_regs_altbank(int set);
 extern void set_altbank(void);
 extern void set_px_go(void);
 extern void set_px_go_with_watchdog(void);
-extern int disable_watchdog(cmd_tbl_t *cmdtp,
-			    int flag, int argc, char *argv[]);
-extern ulong strfractoint(uchar *strptr);

board/icecube/icecube.c

@@ -42,6 +42,53 @@
 #include "mt48lc16m16a2-75.h"
 # endif
 #endif
+
+#ifdef CONFIG_LITE5200B_PM
+/* u-boot part of low-power mode implementation */
+#define SAVED_ADDR (*(void **)0x00000000)
+#define PSC2_4 0x02
+
+void lite5200b_wakeup(void)
+{
+	unsigned char wakeup_pin;
+	void (*linux_wakeup)(void);
+
+	/* check PSC2_4, if it's down "QT" is signaling we have a wakeup
+	 * from low power mode */
+	*(vu_char *)MPC5XXX_WU_GPIO_ENABLE = PSC2_4;
+	__asm__ volatile ("sync");
+
+	wakeup_pin = *(vu_char *)MPC5XXX_WU_GPIO_DATA_I;
+	if (wakeup_pin & PSC2_4)
+		return;
+
+	/* acknowledge to "QT"
+	 * by holding pin at 1 for 10 uS */
+	*(vu_char *)MPC5XXX_WU_GPIO_DIR = PSC2_4;
+	__asm__ volatile ("sync");
+	*(vu_char *)MPC5XXX_WU_GPIO_DATA_O = PSC2_4;
+	__asm__ volatile ("sync");
+	udelay(10);
+
+	/* put ram out of self-refresh */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x80000000;	/* mode_en */
+	__asm__ volatile ("sync");
+	*(vu_long *)MPC5XXX_SDRAM_CTRL |= 0x50000000;	/* cke ref_en */
+	__asm__ volatile ("sync");
+	*(vu_long *)MPC5XXX_SDRAM_CTRL &= ~0x80000000;	/* !mode_en */
+	__asm__ volatile ("sync");
+	udelay(10); /* wait a bit */
+
+	/* jump back to linux kernel code */
+	linux_wakeup = SAVED_ADDR;
+	printf("\n\nLooks like we just woke, transferring control to 0x%08lx\n",
+			linux_wakeup);
+	linux_wakeup();
+}
+#else
+#define lite5200b_wakeup()
+#endif
+
 #ifndef CFG_RAMBOOT
 static void sdram_start (int hi_addr)
 {
@@ -208,6 +255,8 @@ long int initdram (int board_type)
 		__asm__ volatile ("sync");
 	}
 
+	lite5200b_wakeup();
+
 	return dramsize + dramsize2;
 }
 

board/mcc200/lcd.c

@@ -180,10 +180,6 @@ void lcd_enable (void)
 			break;
 		udelay (PSOC_WAIT_TIME);
 	}
-	if (!retries) {
-		printf ("%s Warning: PSoC doesn't respond on "
-			"RTS NEGATE\n",	__FUNCTION__);
-	}
 
 	return;
 }

board/mpc7448hpc2/Makefile

@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o tsi108_init.o
+SOBJS	:= asm_init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+.PHONY: distclean
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude ($obj).depend
+
+#########################################################################

board/mpc7448hpc2/asm_init.S

@@ -0,0 +1,918 @@
+/*
+ * (C) Copyright 2004-05;  Tundra Semiconductor Corp.
+ *
+ * Added automatic detect of SDC settings
+ * Copyright (c) 2005 Freescale Semiconductor, Inc.
+ * Maintainer tie-fei.zang@freescale.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * FILENAME: asm_init.s
+ *
+ * Originator: Alex Bounine
+ *
+ * DESCRIPTION:
+ * Initialization code for the Tundra Tsi108 bridge chip
+ *
+ */
+
+#include <config.h>
+#include <version.h>
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/processor.h>
+
+#include <tsi108.h>
+
+/*
+ * Build Configuration Options
+ */
+
+/* #define DISABLE_PBM		disables usage of PB Master */
+/* #define SDC_HARDCODED_INIT	config SDRAM controller with hardcoded values */
+/* #define SDC_AUTOPRECH_EN	enable SDRAM auto precharge */
+
+/*
+ * Hardcoded SDC settings
+ */
+
+#ifdef SDC_HARDCODED_INIT
+
+/* Micron MT9HTF6472AY-40EA1 : Unbuffered, 512MB, 400, CL3, Single Rank */
+
+#define VAL_SD_REFRESH	(0x61A)
+#define VAL_SD_TIMING	(0x0308336b)
+#define VAL_SD_D0_CTRL	(0x07100021)	/* auto-precharge disabled */
+#define VAL_SD_D0_BAR	(0x0FE00000)	/* 512MB @ 0x00000000 */
+#define VAL_SD_D1_CTRL	(0x07100021)	/* auto-precharge disabled */
+#define VAL_SD_D1_BAR	(0x0FE00200)	/* 512MB @ 0x20000000 */
+
+#endif /* SDC_HARDCODED_INIT */
+
+/*
+ CPU Configuration:
+
+ CPU Address and Data Parity enables.
+
+#define CPU_AP
+#define CPU_DP
+*/
+
+/*
+ * Macros
+ * !!! Attention !!! Macros LOAD_PTR, LOAD_U32 and LOAD_MEM defined below are
+ * expected to work correctly for the CSR space within 32KB range.
+ *
+ * LOAD_PTR and LOAD_U32 - load specified register with a 32 bit constant.
+ * These macros are absolutely identical except their names. This difference
+ * is provided intentionally for better readable code.
+ */
+
+#define LOAD_PTR(reg,const32) \
+	addis reg,r0,const32@h; ori reg,reg,const32@l
+
+#define LOAD_U32(reg,const32) \
+	addis reg,r0,const32@h; ori reg,reg,const32@l
+
+/* LOADMEM initializes a register with the contents of a specified 32-bit
+ * memory location, usually a CSR value.
+ */
+
+#define LOAD_MEM(reg,addr32) \
+	addis reg,r0,addr32@ha; lwz reg,addr32@l(reg)
+
+#ifndef SDC_HARDCODED_INIT
+sdc_clk_sync:
+	/* MHz: 0,0,183,100,133,167,200,233 */
+	.long	0, 0, 6, 10, 8, 6, 5, 4		/* nSec */
+#endif
+
+/*
+ * board_asm_init() - early initialization function. Coded to be portable to
+ * dual-CPU configuration.
+ * Checks CPU number and performs board HW initialization if called for CPU0.
+ * Registers used: r3,r4,r5,r6,r19,r29
+ *
+ * NOTE: For dual-CPU configuration only CPU0 is allowed to configure Tsi108
+ * and the rest of the board. Current implementation demonstrates two
+ * possible ways to identify CPU number:
+ * - for MPC74xx platform: uses MSSCR0[ID] bit as defined in UM.
+ * - for PPC750FX/GX boards: uses WHO_AM_I bit reported by Tsi108.
+ */
+
+	.globl board_asm_init
+board_asm_init:
+	mflr	r19	/* Save LR to be able return later. */
+	bl	icache_enable	/* Enable icache to reduce reads from flash. */
+
+/* Initialize pointer to Tsi108 register space */
+
+	LOAD_PTR(r29,CFG_TSI108_CSR_RST_BASE)/* r29 - pointer to tsi108 CSR space */
+	ori r4,r29,TSI108_PB_REG_OFFSET
+
+/* Check Processor Version Number */
+
+	mfspr	r3, PVR
+	rlwinm	r3,r3,16,16,23	/* get ((Processor Version Number) & 0xFF00) */
+
+	cmpli	0,0,r3,0x8000	/* MPC74xx */
+	bne	cont_brd_init
+
+	/*
+	 * For MPC744x/5x enable extended BATs[4-7]
+	 * Sri: Set HIGH_BAT_EN and XBSEN, and SPD =1
+	 * to disable prefetch
+	 */
+
+	mfspr	r5, HID0
+	oris	r5, r5, 0x0080	/* Set HID0[HIGH_BAT_EN] bit #8 */
+	ori	r5, r5, 0x0380	/* Set SPD,XBSEN,SGE bits #22,23,24 */
+	mtspr	HID0, r5
+	isync
+	sync
+
+	/* Adding code to disable external interventions in MPX bus mode */
+	mfspr	r3, 1014
+	oris	r3, r3, 0x0100	/* Set the EIDIS bit in MSSCR0:  bit 7 */
+	mtspr	1014, r3
+	isync
+	sync
+
+	/* Sri: code to enable FP unit */
+	mfmsr	r3
+	ori	r3, r3, 0x2000
+	mtmsr	r3
+	isync
+	sync
+
+	/* def CONFIG_DUAL_CPU
+	 * For MPC74xx processor, use MSSCR0[ID] bit to identify CPU number.
+	 */
+#if(1)
+	mfspr	r3,1014		/* read MSSCR0 */
+	rlwinm.	r3,r3,27,31,31	/* get processor ID number */
+	mtspr	SPRN_PIR,r3	/* Save CPU ID */
+	sync
+	bne	init_done
+	b	do_tsi108_init
+
+cont_brd_init:
+
+	/* An alternative method of checking the processor number (in addition
+	 * to configuration using MSSCR0[ID] bit on MPC74xx).
+	 * Good for IBM PPC750FX/GX.
+	 */
+
+	lwz	r3,PB_BUS_MS_SELECT(r4)	/* read PB_ID register */
+	rlwinm.	r3,r3,24,31,31		/* get processor ID number */
+	bne init_done
+#else
+
+cont_brd_init:
+
+#endif /* CONFIG_DUAL_CPU */
+
+	/* Initialize Tsi108 chip */
+
+do_tsi108_init:
+
+	/*
+	 * Adjust HLP/Flash parameters. By default after reset the HLP port is
+	 * set to support slow devices. Better performance can be achived when
+	 * an optimal parameters are used for specific EPROM device.
+	 * NOTE: This should be performed ASAP for the emulation platform
+	 * because it has 5MHz HLP clocking.
+	 */
+
+#ifdef CONFIG_TSI108EMU
+	ori	r4,r29,TSI108_HLP_REG_OFFSET
+	LOAD_U32(r5,0x434422c0)
+	stw	r5,0x08(r4)	/* set HLP B0_CTRL0 */
+	sync
+	LOAD_U32(r5,0xd0012000)
+	stw	r5,0x0c(r4)		/* set HLP B0_CTRL1 */
+	sync
+#endif
+
+	/* Initialize PB interface. */
+
+	ori r4,r29,TSI108_PB_REG_OFFSET
+
+#if (CFG_TSI108_CSR_BASE != CFG_TSI108_CSR_RST_BASE)
+	/* Relocate (if required) Tsi108 registers. Set new value for
+	 * PB_REG_BAR:
+	 * Note we are in the 32-bit address mode.
+	 */
+	LOAD_U32(r5,(CFG_TSI108_CSR_BASE | 0x01)) /* PB_REG_BAR: BA + EN */
+	stw	r5,PB_REG_BAR(r4)
+	andis.	r29,r5,0xFFFF
+	sync
+	ori	r4,r29,TSI108_PB_REG_OFFSET
+#endif
+
+	/* Set PB Slave configuration register */
+
+	LOAD_U32(r5,0x00002481)	/* PB_SCR: TEA enabled,AACK delay = 1 */
+	lwz	r3, PB_RSR(r4)	/* get PB bus mode */
+	xori	r3,r3,0x0001	/* mask PB_BMODE: r3 -> (0 = 60X, 1 = MPX) */
+	rlwimi  r5,r3,14,17,17	/* for MPX: set DTI_MODE bit */
+	stw	r5,PB_SCR(r4)
+	sync
+
+	/* Configure PB Arbiter */
+
+	lwz	r5,PB_ARB_CTRL(r4)	/* Read PB Arbiter Control Register */
+	li	r3, 0x00F0		/* ARB_PIPELINE_DEP mask */
+#ifdef DISABLE_PBM
+	ori	r3,r3,0x1000	/* add PBM_EN to clear (enabled by default) */
+#endif
+	andc	r5,r5,r3	/* Clear the masked bit fields */
+	ori	r5,r5,0x0001	/* Set pipeline depth */
+	stw	r5,PB_ARB_CTRL(r4)
+
+#if (0)	/* currently using the default settings for PBM after reset */
+	LOAD_U32(r5,0x)		/* value for PB_MCR */
+	stw	r5,PB_MCR(r4)
+	sync
+
+	LOAD_U32(r5,0x)		/* value for PB_MCMD */
+	stw	r5,PB_MCMD(r4)
+	sync
+#endif
+
+	/* Disable or enable PVT based on processor bus frequency
+	 * 1. Read CG_PWRUP_STATUS register field bits 18,17,16
+	 * 2. See if the value is < or > 133mhz (18:16 = 100)
+	 * 3. If > enable PVT
+	 */
+
+	LOAD_U32(r3,0xC0002234)
+	lwz	r3,0(r3)
+	rlwinm	r3,r3,16,29,31
+
+	cmpi	0,0,r3,0x0004
+	bgt	sdc_init
+
+#ifndef CONFIG_TSI108EMU
+	/* FIXME: Disable PB calibration control for any real Tsi108 board */
+	li	r5,0x0101	/* disable calibration control */
+	stw	r5,PB_PVT_CTRL2(r4)
+	sync
+#endif
+
+	/* Initialize SDRAM controller. */
+
+sdc_init:
+
+#ifndef SDC_HARDCODED_INIT
+	/* get SDC clock prior doing sdram controller autoconfig */
+	ori	r4,r29,TSI108_CLK_REG_OFFSET	/* r4 - ptr to CG registers */
+	lwz	r3, CG_PWRUP_STATUS(r4)		/* get CG configuration */
+	rlwinm	r3,r3,12,29,31			/* r3 - SD clk */
+	lis	r5,sdc_clk_sync@h
+	ori	r5,r5,sdc_clk_sync@l
+	/* Sri:  At this point check if r3 = 001. If yes,
+	 * the memory frequency should be same as the
+	 * MPX bus frequency
+	 */
+	cmpi	0,0,r3,0x0001
+	bne	get_nsec
+	lwz	r6, CG_PWRUP_STATUS(r4)
+	rlwinm	r6,r6,16,29,31
+	mr	r3,r6
+
+get_nsec:
+	rlwinm	r3,r3,2,0,31
+	lwzx	r9,r5,r3	/* get SD clk rate in nSec */
+	/* ATTN: r9 will be used by SPD routine */
+#endif /* !SDC_HARDCODED_INIT */
+
+	ori	r4,r29,TSI108_SD_REG_OFFSET /* r4 - ptr to SDRAM registers */
+
+	/* Initialize SDRAM controller. SDRAM Size = 512MB, One DIMM. */
+
+	LOAD_U32(r5,0x00)
+	stw	r5,SD_INT_ENABLE(r4) /* Ensure that interrupts are disabled */
+#ifdef ENABLE_SDRAM_ECC
+	li	r5, 0x01
+#endif /* ENABLE_SDRAM_ECC */
+	stw	r5,SD_ECC_CTRL(r4)	/* Enable/Disable ECC */
+	sync
+
+#ifdef SDC_HARDCODED_INIT /* config sdram controller with hardcoded values */
+
+	/* First read the CG_PWRUP_STATUS register to get the
+	 * memory speed from bits 22,21,20
+	 */
+
+	LOAD_U32(r3,0xC0002234)
+	lwz	r3,0(r3)
+	rlwinm	r3,r3,12,29,31
+
+	/* Now first check for 166, then 200, or default */
+
+	cmpi	0,0,r3,0x0005
+	bne	check_for_200mhz
+
+	/* set values for 166 Mhz memory speed
+	 * Set refresh rate and timing parameters
+	 */
+	LOAD_U32(r5,0x00000515)
+	stw	r5,SD_REFRESH(r4)
+	LOAD_U32(r5,0x03073368)
+	stw	r5,SD_TIMING(r4)
+	sync
+
+	/* Initialize DIMM0 control and BAR registers */
+	LOAD_U32(r5,VAL_SD_D0_CTRL)	/* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+	oris	r5,r5,0x0001		/* set auto precharge EN bit */
+#endif
+	stw	r5,SD_D0_CTRL(r4)
+	LOAD_U32(r5,VAL_SD_D0_BAR)
+	stw	r5,SD_D0_BAR(r4)
+	sync
+
+	/* Initialize DIMM1 control and BAR registers
+	 * (same as dimm 0, next 512MB, disabled)
+	 */
+	LOAD_U32(r5,VAL_SD_D1_CTRL)	/* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+	oris	r5,r5,0x0001	/* set auto precharge EN bit */
+#endif
+	stw	r5,SD_D1_CTRL(r4)
+	LOAD_U32(r5,VAL_SD_D1_BAR)
+	stw	r5,SD_D1_BAR(r4)
+	sync
+
+	b	sdc_init_done
+
+check_for_200mhz:
+
+	cmpi	0,0,r3,0x0006
+	bne	set_default_values
+
+	/* set values for 200Mhz memory speed
+	 * Set refresh rate and timing parameters
+	 */
+	LOAD_U32(r5,0x0000061a)
+	stw	r5,SD_REFRESH(r4)
+	LOAD_U32(r5,0x03083348)
+	stw	r5,SD_TIMING(r4)
+	sync
+
+	/* Initialize DIMM0 control and BAR registers */
+	LOAD_U32(r5,VAL_SD_D0_CTRL)	/* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+	oris	r5,r5,0x0001		/* set auto precharge EN bit */
+#endif
+	stw	r5,SD_D0_CTRL(r4)
+	LOAD_U32(r5,VAL_SD_D0_BAR)
+	stw	r5,SD_D0_BAR(r4)
+	sync
+
+	/* Initialize DIMM1 control and BAR registers
+	 * (same as dimm 0, next 512MB, disabled)
+	 */
+	LOAD_U32(r5,VAL_SD_D1_CTRL)	/* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+	oris	r5,r5,0x0001		/* set auto precharge EN bit */
+#endif
+	stw	r5,SD_D1_CTRL(r4)
+	LOAD_U32(r5,VAL_SD_D1_BAR)
+	stw	r5,SD_D1_BAR(r4)
+	sync
+
+	b	sdc_init_done
+
+set_default_values:
+
+	/* Set refresh rate and timing parameters */
+	LOAD_U32(r5,VAL_SD_REFRESH)
+	stw	r5,SD_REFRESH(r4)
+	LOAD_U32(r5,VAL_SD_TIMING)
+	stw	r5,SD_TIMING(r4)
+	sync
+
+	/* Initialize DIMM0 control and BAR registers */
+	LOAD_U32(r5,VAL_SD_D0_CTRL)	/* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+	oris	r5,r5,0x0001		/* set auto precharge EN bit */
+#endif
+	stw 	r5,SD_D0_CTRL(r4)
+	LOAD_U32(r5,VAL_SD_D0_BAR)
+	stw	r5,SD_D0_BAR(r4)
+	sync
+
+	/* Initialize DIMM1 control and BAR registers
+	 * (same as dimm 0, next 512MB, disabled)
+	 */
+	LOAD_U32(r5,VAL_SD_D1_CTRL)	/* auto-precharge disabled */
+#ifdef SDC_AUTOPRECH_EN
+	oris	r5,r5,0x0001		/* set auto precharge EN bit */
+#endif
+	stw	r5,SD_D1_CTRL(r4)
+	LOAD_U32(r5,VAL_SD_D1_BAR)
+	stw	r5,SD_D1_BAR(r4)
+	sync
+#else /* !SDC_HARDCODED_INIT */
+	bl	tsi108_sdram_spd	/* automatically detect SDC settings */
+#endif /* SDC_HARDCODED_INIT */
+
+sdc_init_done:
+
+#ifdef DISABLE_PBM
+	LOAD_U32(r5,0x00000030)		/* PB_EN + OCN_EN */
+#else
+	LOAD_U32(r5,0x00000230)		/* PB_EN + OCN_EN + PB/OCN=80/20 */
+#endif /* DISABLE_PBM */
+
+#ifdef CONFIG_TSI108EMU
+	oris	r5,r5,0x0010		/* set EMULATION_MODE bit */
+#endif
+
+	stw	r5,SD_CTRL(r4)
+	eieio
+	sync
+
+	/* Enable SDRAM access */
+
+	oris	r5,r5,0x8000		/* start SDC: set SD_CTRL[ENABLE] bit */
+	stw	r5,SD_CTRL(r4)
+	sync
+
+wait_init_complete:
+	lwz	r5,SD_STATUS(r4)
+	andi.	r5,r5,0x0001
+	/* wait until SDRAM initialization is complete */
+	beq	wait_init_complete
+
+	/* Map SDRAM into the processor bus address space */
+
+	ori	r4,r29,TSI108_PB_REG_OFFSET
+
+	/* Setup BARs associated with direct path PB<->SDRAM */
+
+	/* PB_SDRAM_BAR1:
+	 * provides a direct path to the main system memory (cacheable SDRAM)
+	 */
+
+	/* BA=0,Size=512MB, ENable, No Addr.Translation */
+	LOAD_U32(r5, 0x00000011)
+	stw	r5,PB_SDRAM_BAR1(r4)
+	sync
+
+	/* Make sure that PB_SDRAM_BAR1 decoder is set
+	 * (to allow following immediate read from SDRAM)
+	 */
+	lwz	r5,PB_SDRAM_BAR1(r4)
+	sync
+
+	/* PB_SDRAM_BAR2:
+	 * provides non-cacheable alias (via the direct path) to main
+	 * system memory.
+	 * Size = 512MB, ENable, Addr.Translation - ON,
+	 * BA = 0x0_40000000, TA = 0x0_00000000
+	 */
+
+	LOAD_U32(r5, 0x40010011)
+	stw	r5,PB_SDRAM_BAR2(r4)
+	sync
+
+	/* Make sure that PB_SDRAM_BAR2 decoder is set
+	 * (to allow following immediate read from SDRAM)
+	 */
+	lwz	r5,PB_SDRAM_BAR2(r4)
+	sync
+
+init_done:
+
+	/* All done. Restore LR and return. */
+	mtlr	r19
+	blr
+
+#if (0)
+	/*
+	 * init_cpu1
+	 * This routine enables CPU1 on the dual-processor system.
+	 * Now there is only one processor in the system
+	 */
+
+	.global enable_cpu1
+enable_cpu1:
+
+	lis	r3,Tsi108_Base@ha	/* Get Grendel CSR Base Addr */
+	addi	r3,r3,Tsi108_Base@l
+	lwz	r3,0(r3)		/* R3 = CSR Base Addr */
+	ori	r4,r3,TSI108_PB_REG_OFFSET
+	lwz	r3,PB_ARB_CTRL(r4)	/* Read PB Arbiter Control Register */
+	ori	r3,r3,0x0200		/* Set M1_EN bit */
+	stw	r3,PB_ARB_CTRL(r4)
+
+	blr
+#endif
+
+	/*
+	 * enable_EI
+	 * Enable CPU core external interrupt
+	 */
+
+	.global	enable_EI
+enable_EI:
+	mfmsr	r3
+	ori	r3,r3,0x8000	/* set EE bit */
+	mtmsr	r3
+	blr
+
+	/*
+	 * disable_EI
+	 * Disable CPU core external interrupt
+	 */
+
+	.global disable_EI
+disable_EI:
+	mfmsr	r3
+	li	r4,-32768	/* aka "li  r4,0x8000" */
+	andc	r3,r3,r4	/* clear EE bit */
+	mtmsr	r3
+	blr
+
+#ifdef ENABLE_SDRAM_ECC
+	/* enables SDRAM ECC  */
+
+	.global	enable_ECC
+enable_ECC:
+	ori	r4,r29,TSI108_SD_REG_OFFSET
+	lwz	r3,SD_ECC_CTRL(r4)	/* Read SDRAM ECC Control Register */
+	ori	r3,r3,0x0001		/* Set ECC_EN bit */
+	stw	r3,SD_ECC_CTRL(r4)
+	blr
+
+	/*
+	 * clear_ECC_err
+	 * Clears all pending SDRAM ECC errors
+	 * (normally after SDRAM scrubbing/initialization)
+	 */
+
+	.global	clear_ECC_err
+clear_ECC_err:
+	ori r4,r29,TSI108_SD_REG_OFFSET
+	ori r3,r0,0x0030	/* ECC_UE_INT + ECC_CE_INT bits */
+	stw r3,SD_INT_STATUS(r4)
+	blr
+
+#endif /* ENABLE_SDRAM_ECC */
+
+#ifndef SDC_HARDCODED_INIT
+
+	/* SDRAM SPD Support */
+#define	SD_I2C_CTRL1	(0x400)
+#define	SD_I2C_CTRL2	(0x404)
+#define SD_I2C_RD_DATA	(0x408)
+#define SD_I2C_WR_DATA	(0x40C)
+
+	/*
+	 * SDRAM SPD Support Macros
+	 */
+
+#define SPD_DIMM0	(0x00000100)
+#define SPD_DIMM1	(0x00000200)	/* SPD_DIMM1 was 0x00000000 */
+
+#define SPD_RDIMM			(0x01)
+#define SPD_UDIMM			(0x02)
+
+#define SPD_CAS_3			0x8
+#define SPD_CAS_4			0x10
+#define SPD_CAS_5			0x20
+
+#define ERR_NO_DIMM_FOUND		(0xdb0)
+#define ERR_TRAS_FAIL			(0xdb1)
+#define ERR_TRCD_FAIL			(0xdb2)
+#define ERR_TRP_FAIL			(0xdb3)
+#define ERR_TWR_FAIL			(0xdb4)
+#define ERR_UNKNOWN_PART		(0xdb5)
+#define ERR_NRANK_INVALID		(0xdb6)
+#define ERR_DIMM_SIZE			(0xdb7)
+#define ERR_ADDR_MODE			(0xdb8)
+#define ERR_RFRSH_RATE			(0xdb9)
+#define ERR_DIMM_TYPE			(0xdba)
+#define ERR_CL_VALUE			(0xdbb)
+#define ERR_TRFC_FAIL			(0xdbc)
+
+/* READ_SPD requirements:
+ * byte - byte address in SPD device (0 - 255)
+ * r3 = will return data read from I2C Byte location
+ * r4 - unchanged (SDC base addr)
+ * r5 - clobbered in routine (I2C status)
+ * r10 - number of DDR slot where first SPD device is detected
+ */
+
+#define READ_SPD(byte_num)		\
+	addis	r3, 0, byte_num@l;	\
+	or	r3, r3, r10;		\
+	ori	r3, r3, 0x0A;		\
+	stw	r3, SD_I2C_CTRL1(r4);	\
+	li	r3, I2C_CNTRL2_START;	\
+	stw	r3, SD_I2C_CTRL2(r4);	\
+	eieio;				\
+	sync;				\
+	li	r3, 0x100;		\
+1:;					\
+	addic.	r3, r3, -1;		\
+	bne	1b;			\
+2:;					\
+	lwz	r5, SD_I2C_CTRL2(r4);	\
+	rlwinm.	r3,r5,0,23,23;		\
+	bne	2b;			\
+	rlwinm.	r3,r5,0,3,3;		\
+	lwz	r3,SD_I2C_RD_DATA(r4)
+
+#define SPD_MIN_RFRSH	(0x80)
+#define SPD_MAX_RFRSH	(0x85)
+
+refresh_rates:	/* in nSec */
+	.long	15625	/* Normal (0x80) */
+	.long	3900	/* Reduced 0.25x (0x81) */
+	.long	7800	/* Reduced 0.5x (0x82) */
+	.long	31300	/* Extended 2x (0x83) */
+	.long	62500	/* Extended 4x (0x84) */
+	.long	125000	/* Extended 8x (0x85) */
+
+/*
+ * tsi108_sdram_spd
+ *
+ * Inittializes SDRAM Controller using DDR2 DIMM Serial Presence Detect data
+ * Uses registers: r4 - SDC base address (not changed)
+ *				   r9 - SDC clocking period in nSec
+ * Changes registers: r3,r5,r6,r7,r8,r10,r11
+ */
+
+tsi108_sdram_spd:
+
+	li	r10,SPD_DIMM0
+	xor	r11,r11,r11		/* DIMM Base Address: starts from 0 */
+
+do_first_dimm:
+
+	/* Program Refresh Rate	Register */
+
+	READ_SPD(12)			/* get Refresh Rate */
+	beq	check_next_slot
+	li	r5, ERR_RFRSH_RATE
+	cmpi	0,0,r3,SPD_MIN_RFRSH
+	ble	spd_fail
+	cmpi	0,0,r3,SPD_MAX_RFRSH
+	bgt	spd_fail
+	addi	r3,r3,-SPD_MIN_RFRSH
+	rlwinm	r3,r3,2,0,31
+	lis	r5,refresh_rates@h
+	ori	r5,r5,refresh_rates@l
+	lwzx	r5,r5,r3		/* get refresh rate in nSec */
+	divwu	r5,r5,r9		/* calculate # of SDC clocks */
+	stw	r5,SD_REFRESH(r4)	/* Set refresh rate */
+	sync
+
+	/* Program SD Timing Register */
+
+	li	r7, 0		/* clear r7 prior parameter collection */
+
+	READ_SPD(20)		/* get DIMM type: Registered or Unbuffered */
+	beq	spd_read_fail
+	li	r5, ERR_DIMM_TYPE
+	cmpi	0,0,r3,SPD_UDIMM
+	beq	do_cl
+	cmpi	0,0,r3,SPD_RDIMM
+	bne	spd_fail
+	oris	r7,r7,0x1000	/* set SD_TIMING[DIMM_TYPE] bit */
+
+do_cl:
+	READ_SPD(18)		/* Get CAS Latency */
+	beq	spd_read_fail
+	li	r5,ERR_CL_VALUE
+	andi.	r6,r3,SPD_CAS_3
+	beq	cl_4
+	li	r6,3
+	b	set_cl
+cl_4:
+	andi.	r6,r3,SPD_CAS_4
+	beq	cl_5
+	li	r6,4
+	b	set_cl
+cl_5:
+	andi.	r6,r3,SPD_CAS_5
+	beq	spd_fail
+	li	r6,5
+set_cl:
+	rlwimi	r7,r6,24,5,7
+
+	READ_SPD(30)		/* Get tRAS */
+	beq	spd_read_fail
+	divwu	r6,r3,r9
+	mullw	r8,r6,r9
+	subf.	r8,r8,r3
+	beq	set_tras
+	addi	r6,r6,1
+set_tras:
+	li r5,ERR_TRAS_FAIL
+	cmpi	0,0,r6,0x0F	/* max supported value */
+	bgt	spd_fail
+	rlwimi	r7,r6,16,12,15
+
+	READ_SPD(29)	/* Get tRCD */
+	beq	spd_read_fail
+	/* right shift tRCD by 2 bits as per DDR2 spec */
+	rlwinm	r3,r3,30,2,31
+	divwu	r6,r3,r9
+	mullw	r8,r6,r9
+	subf.	r8,r8,r3
+	beq	set_trcd
+	addi	r6,r6,1
+set_trcd:
+	li	r5,ERR_TRCD_FAIL
+	cmpi	0,0,r6,0x07	/* max supported value */
+	bgt	spd_fail
+	rlwimi	r7,r6,12,17,19
+
+	READ_SPD(27)	/* Get tRP value */
+	beq	spd_read_fail
+	rlwinm	r3,r3,30,2,31	/* right shift tRP by 2 bits as per DDR2 spec */
+	divwu	r6,r3,r9
+	mullw	r8,r6,r9
+	subf.	r8,r8,r3
+	beq	set_trp
+	addi	r6,r6,1
+set_trp:
+	li	r5,ERR_TRP_FAIL
+	cmpi	0,0,r6,0x07	/* max supported value */
+	bgt	spd_fail
+	rlwimi	r7,r6,8,21,23
+
+	READ_SPD(36)	/* Get tWR value */
+	beq	spd_read_fail
+	rlwinm	r3,r3,30,2,31	/* right shift tWR by 2 bits as per DDR2 spec */
+	divwu	r6,r3,r9
+	mullw	r8,r6,r9
+	subf.	r8,r8,r3
+	beq	set_twr
+	addi	r6,r6,1
+set_twr:
+	addi	r6,r6,-1	/* Tsi108 SDC always gives one extra clock */
+	li	r5,ERR_TWR_FAIL
+	cmpi	0,0,r6,0x07	/* max supported value */
+	bgt	spd_fail
+	rlwimi	r7,r6,5,24,26
+
+	READ_SPD(42)	/* Get tRFC */
+	beq	spd_read_fail
+	li	r5, ERR_TRFC_FAIL
+	/* Tsi108 spec: tRFC=(tRFC + 1)/2 */
+	addi	r3,r3,1
+	rlwinm.	r3,r3,31,1,31	/* divide by 2 */
+	beq	spd_fail
+	divwu	r6,r3,r9
+	mullw	r8,r6,r9
+	subf.	r8,r8,r3
+	beq	set_trfc
+	addi	r6,r6,1
+set_trfc:
+	cmpi	0,0,r6,0x1F	/* max supported value */
+	bgt	spd_fail
+	rlwimi	r7,r6,0,27,31
+
+	stw	r7,SD_TIMING(r4)
+	sync
+
+	/*
+	 * The following two registers are set on per-DIMM basis.
+	 * The SD_REFRESH and SD_TIMING settings are common for both DIMMS
+	 */
+
+do_each_dimm:
+
+	/* Program SDRAM DIMM Control Register */
+
+	li	r7, 0		/* clear r7 prior parameter collection */
+
+	READ_SPD(13)		/* Get Primary SDRAM Width */
+	beq	spd_read_fail
+	cmpi	0,0,r3,4	/* Check for 4-bit SDRAM */
+	beq	do_nbank
+	oris	r7,r7,0x0010	/* Set MEM_WIDTH bit */
+
+do_nbank:
+	READ_SPD(17)		/* Get Number of banks on SDRAM device */
+	beq	spd_read_fail
+	/* Grendel only distinguish betw. 4 or 8-bank memory parts */
+	li	r5,ERR_UNKNOWN_PART	/* non-supported memory part */
+	cmpi	0,0,r3,4
+	beq	do_nrank
+	cmpi	0,0,r3,8
+	bne	spd_fail
+	ori	r7,r7,0x1000
+
+do_nrank:
+	READ_SPD(5)		/* Get # of Ranks */
+	beq	spd_read_fail
+	li	r5,ERR_NRANK_INVALID
+	andi.	r6,r3,0x7	/* Use bits [2..0] only */
+	beq	do_addr_mode
+	cmpi	0,0,r6,1
+	bgt	spd_fail
+	rlwimi	r7,r6,8,23,23
+
+do_addr_mode:
+	READ_SPD(4)		/* Get # of Column Addresses */
+	beq	spd_read_fail
+	li	r5, ERR_ADDR_MODE
+	andi.	r3,r3,0x0f	/* cut off reserved bits */
+	cmpi	0,0,r3,8
+	ble	spd_fail
+	cmpi	0,0,r3,15
+	bgt	spd_fail
+	addi	r6,r3,-8	/* calculate ADDR_MODE parameter */
+	rlwimi	r7,r6,4,24,27	/* set ADDR_MODE field */
+
+set_dimm_ctrl:
+#ifdef SDC_AUTOPRECH_EN
+	oris	r7,r7,0x0001	/* set auto precharge EN bit */
+#endif
+	ori	r7,r7,1		/* set ENABLE bit */
+	cmpi	0,0,r10,SPD_DIMM0
+	bne	1f
+	stw	r7,SD_D0_CTRL(r4)
+	sync
+	b	set_dimm_bar
+1:
+	stw	r7,SD_D1_CTRL(r4)
+	sync
+
+
+	/* Program SDRAM DIMMx Base Address Register */
+
+set_dimm_bar:
+	READ_SPD(5)		/* get # of Ranks */
+	beq	spd_read_fail
+	andi.	r7,r3,0x7
+	addi	r7,r7,1
+	READ_SPD(31)		/* Read DIMM rank density */
+	beq	spd_read_fail
+	rlwinm	r5,r3,27,29,31
+	rlwinm	r6,r3,3,24,28
+	or	r5,r6,r5	/* r5 = Normalized Rank Density byte */
+	lis	r8, 0x0080	/* 128MB >> 4 */
+	mullw	r8,r8,r5	/* r8 = (rank_size >> 4) */
+	mullw	r8,r8,r7	/* r8 = (DIMM_size >> 4) */
+	neg	r7,r8
+	rlwinm	r7,r7,28,4,31
+	or	r7,r7,r11	/* set ADDR field */
+	rlwinm	r8,r8,12,20,31
+	add	r11,r11,r8	/* set Base Addr for next DIMM */
+
+	cmpi	0,0,r10,SPD_DIMM0
+	bne	set_dimm1_size
+	stw	r7,SD_D0_BAR(r4)
+	sync
+	li	r10,SPD_DIMM1
+	READ_SPD(0)
+	bne do_each_dimm
+	b spd_done
+
+set_dimm1_size:
+	stw	r7,SD_D1_BAR(r4)
+	sync
+spd_done:
+	blr
+
+check_next_slot:
+	cmpi	0,0,r10,SPD_DIMM1
+	beq	spd_read_fail
+	li	r10,SPD_DIMM1
+	b	do_first_dimm
+spd_read_fail:
+	ori	r3,r0,0xdead
+	b	err_hung
+spd_fail:
+	li	r3,0x0bad
+	sync
+err_hung:	/* hang here for debugging */
+	nop
+	nop
+	b	err_hung
+
+#endif /* !SDC_HARDCODED_INIT */

board/mpc7448hpc2/config.mk

@@ -0,0 +1,28 @@
+#
+# Copyright (c) 2005 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+# Flash address
+TEXT_BASE = 0xFF000000
+# RAM address
+#TEXT_BASE = 0x00400000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -maltivec -mabi=altivec -msoft-float

board/mpc7448hpc2/mpc7448hpc2.c

@@ -0,0 +1,107 @@
+/*
+ * (C) Copyright 2005 Freescale Semiconductor, Inc.
+ *
+ * Roy Zang <tie-fei.zang@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * modifications for the Tsi108 Emul Board by avb@Tundra
+ */
+
+/*
+ * board support/init functions for the
+ * Freescale MPC7448 HPC2 (High-Performance Computing 2 Platform).
+ */
+
+#include <common.h>
+#include <74xx_7xx.h>
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+extern void ft_cpu_setup (void *blob, bd_t *bd);
+#endif
+
+#undef	DEBUG
+
+extern void flush_data_cache (void);
+extern void invalidate_l1_instruction_cache (void);
+extern void tsi108_init_f (void);
+
+int display_mem_map (void);
+
+void after_reloc (ulong dest_addr)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/*
+	 * Jump to the main U-Boot board init code
+	 */
+	board_init_r ((gd_t *) gd, dest_addr);
+	/* NOTREACHED */
+}
+
+/*
+ * Check Board Identity:
+ * report board type
+ */
+
+int checkboard (void)
+{
+	int l_type = 0;
+
+	printf ("BOARD: %s\n", CFG_BOARD_NAME);
+	return (l_type);
+}
+
+/*
+ * Read Processor ID:
+ *
+ * report calling processor number
+ */
+
+int read_pid (void)
+{
+	return 0;		/* we are on single CPU platform for a while */
+}
+
+long int dram_size (int board_type)
+{
+	return 0x20000000;	/* 256M bytes */
+}
+
+long int initdram (int board_type)
+{
+	return dram_size (board_type);
+}
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup (void *blob, bd_t *bd)
+{
+	u32 *p;
+	int len;
+
+	ft_cpu_setup (blob, bd);
+
+	p = ft_get_prop (blob, "/memory/reg", &len);
+	if (p != NULL) {
+		*p++ = cpu_to_be32 (bd->bi_memstart);
+		*p = cpu_to_be32 (bd->bi_memsize);
+	}
+}
+#endif

board/mpc7448hpc2/tsi108_init.c

@@ -0,0 +1,665 @@
+/*****************************************************************************
+ * (C) Copyright 2003;  Tundra Semiconductor Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *****************************************************************************/
+
+/*----------------------------------------------------------------------------
+ * FILENAME: tsi108_init.c
+ *
+ * Originator: Alex Bounine
+ *
+ * DESCRIPTION:
+ * Initialization code for the Tundra Tsi108 bridge chip
+ *---------------------------------------------------------------------------*/
+
+#include <common.h>
+#include <74xx_7xx.h>
+#include <config.h>
+#include <version.h>
+#include <asm/processor.h>
+#include <tsi108.h>
+
+extern void mpicInit (int verbose);
+
+/*
+ * Configuration Options
+ */
+
+typedef struct {
+	ulong upper;
+	ulong lower;
+} PB2OCN_LUT_ENTRY;
+
+PB2OCN_LUT_ENTRY pb2ocn_lut1[32] = {
+	/* 0 - 7 */
+	{0x00000000, 0x00000201}, /* PBA=0xE000_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE100_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE200_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE300_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE400_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE500_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE600_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE700_0000 -> PCI/X (Byte-Swap) */
+
+	/* 8 - 15 */
+	{0x00000000, 0x00000201}, /* PBA=0xE800_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xE900_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xEA00_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xEB00_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xEC00_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xED00_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xEE00_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xEF00_0000 -> PCI/X (Byte-Swap) */
+
+	/* 16 - 23 */
+	{0x00000000, 0x00000201}, /* PBA=0xF000_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF100_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF200_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF300_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF400_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF500_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF600_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF700_0000 -> PCI/X (Byte-Swap) */
+	/* 24 - 31 */
+	{0x00000000, 0x00000201}, /* PBA=0xF800_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xF900_0000 -> PCI/X (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xFA00_0000 -> PCI/X  PCI I/O (Byte-Swap) */
+	{0x00000000, 0x00000201}, /* PBA=0xFB00_0000 -> PCI/X  PCI Config (Byte-Swap) */
+
+	{0x00000000, 0x02000240}, /* PBA=0xFC00_0000 -> HLP */
+	{0x00000000, 0x01000240}, /* PBA=0xFD00_0000 -> HLP */
+	{0x00000000, 0x03000240}, /* PBA=0xFE00_0000 -> HLP */
+	{0x00000000, 0x00000240}  /* PBA=0xFF00_0000 -> HLP : (Translation Enabled + Byte-Swap)*/
+};
+
+#ifdef CFG_CLK_SPREAD
+typedef struct {
+	ulong ctrl0;
+	ulong ctrl1;
+} PLL_CTRL_SET;
+
+/*
+ * Clock Generator SPLL0 initialization values
+ * PLL0 configuration table for various PB_CLKO freq.
+ * Uses pre-calculated values for Fs = 30 kHz, D = 0.5%
+ * Fout depends on required PB_CLKO. Based on Fref = 33 MHz
+ */
+
+static PLL_CTRL_SET pll0_config[8] = {
+	{0x00000000, 0x00000000},	/* 0: bypass */
+	{0x00000000, 0x00000000},	/* 1: reserved */
+	{0x00430044, 0x00000043},	/* 2: CG_PB_CLKO = 183 MHz */
+	{0x005c0044, 0x00000039},	/* 3: CG_PB_CLKO = 100 MHz */
+	{0x005c0044, 0x00000039},	/* 4: CG_PB_CLKO = 133 MHz */
+	{0x004a0044, 0x00000040},	/* 5: CG_PB_CLKO = 167 MHz */
+	{0x005c0044, 0x00000039},	/* 6: CG_PB_CLKO = 200 MHz */
+	{0x004f0044, 0x0000003e}	/* 7: CG_PB_CLKO = 233 MHz */
+};
+#endif	/* CFG_CLK_SPREAD */
+
+/*
+ * Prosessor Bus Clock (in MHz) defined by CG_PB_SELECT
+ * (based on recommended Tsi108 reference clock 33MHz)
+ */
+static int pb_clk_sel[8] = { 0, 0, 183, 100, 133, 167, 200, 233 };
+
+/*
+ * get_board_bus_clk ()
+ *
+ * returns the bus clock in Hz.
+ */
+unsigned long get_board_bus_clk (void)
+{
+	ulong i;
+
+	/* Detect PB clock freq. */
+	i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
+	i = (i >> 16) & 0x07;	/* Get PB PLL multiplier */
+
+	return pb_clk_sel[i] * 1000000;
+}
+
+/*
+ * board_early_init_f ()
+ *
+ * board-specific initialization executed from flash
+ */
+
+int board_early_init_f (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	ulong i;
+
+	gd->mem_clk = 0;
+	i = in32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET +
+			CG_PWRUP_STATUS);
+	i = (i >> 20) & 0x07;	/* Get GD PLL multiplier */
+	switch (i) {
+	case 0:	/* external clock */
+		printf ("Using external clock\n");
+		break;
+	case 1:	/* system clock */
+		gd->mem_clk = gd->bus_clk;
+		break;
+	case 4:	/* 133 MHz */
+	case 5:	/* 166 MHz */
+	case 6:	/* 200 MHz */
+		gd->mem_clk = pb_clk_sel[i] * 1000000;
+		break;
+	default:
+		printf ("Invalid DDR2 clock setting\n");
+		return -1;
+	}
+	printf ("BUS: %d MHz\n", get_board_bus_clk() / 1000000);
+	printf ("MEM: %d MHz\n", gd->mem_clk / 1000000);
+	return 0;
+}
+
+/*
+ * board_early_init_r() - Tsi108 initialization function executed right after
+ * relocation. Contains code that cannot be executed from flash.
+ */
+
+int board_early_init_r (void)
+{
+	ulong temp, i;
+	ulong reg_val;
+	volatile ulong *reg_ptr;
+
+	reg_ptr =
+		(ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900);
+
+	for (i = 0; i < 32; i++) {
+		*reg_ptr++ = 0x00000201;	/* SWAP ENABLED */
+		*reg_ptr++ = 0x00;
+	}
+
+	__asm__ __volatile__ ("eieio");
+	__asm__ __volatile__ ("sync");
+
+	/* Setup PB_OCN_BAR2: size 256B + ENable @ 0x0_80000000 */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2,
+		0x80000001);
+	__asm__ __volatile__ ("sync");
+
+	/* Make sure that OCN_BAR2 decoder is set (to allow following immediate
+	 * read from SDRAM)
+	 */
+
+	temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2);
+	__asm__ __volatile__ ("sync");
+
+	/*
+	 * Remap PB_OCN_BAR1 to accomodate PCI-bus aperture and EPROM into the
+	 * processor bus address space. Immediately after reset LUT and address
+	 * translation are disabled for this BAR. Now we have to initialize LUT
+	 * and switch from the BOOT mode to the normal operation mode.
+	 *
+	 * The aperture defined by PB_OCN_BAR1 startes at address 0xE0000000
+	 * and covers 512MB of address space. To allow larger aperture we also
+	 * have to relocate register window of Tsi108
+	 *
+	 * Initialize LUT (32-entries) prior switching PB_OCN_BAR1 from BOOT
+	 * mode.
+	 *
+	 * initialize pointer to LUT associated with PB_OCN_BAR1
+	 */
+	reg_ptr =
+		(ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x800);
+
+	for (i = 0; i < 32; i++) {
+		*reg_ptr++ = pb2ocn_lut1[i].lower;
+		*reg_ptr++ = pb2ocn_lut1[i].upper;
+	}
+
+	__asm__ __volatile__ ("sync");
+
+	/* Base addresses for CS0, CS1, CS2, CS3 */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_ADDR,
+		0x00000000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_ADDR,
+		0x00100000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_ADDR,
+		0x00200000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_ADDR,
+		0x00300000);
+	__asm__ __volatile__ ("sync");
+
+	/* Masks for HLP banks */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_MASK,
+		0xFFF00000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_MASK,
+		0xFFF00000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_MASK,
+		0xFFF00000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_MASK,
+		0xFFF00000);
+	__asm__ __volatile__ ("sync");
+
+	/* Set CTRL0 values for banks */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL0,
+		0x7FFC44C2);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL0,
+		0x7FFC44C0);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL0,
+		0x7FFC44C0);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL0,
+		0x7FFC44C2);
+	__asm__ __volatile__ ("sync");
+
+	/* Set banks to latched mode, enabled, and other default settings */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL1,
+		0x7C0F2000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL1,
+		0x7C0F2000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL1,
+		0x7C0F2000);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1,
+		0x7C0F2000);
+	__asm__ __volatile__ ("sync");
+
+	/*
+	 * Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode.
+	 * value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable)
+	 */
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1,
+		0xE0000011);
+	__asm__ __volatile__ ("sync");
+
+	/* Make sure that OCN_BAR2 decoder is set (to allow following
+	 * immediate read from SDRAM)
+	 */
+
+	temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1);
+	__asm__ __volatile__ ("sync");
+
+	/*
+	 * SRI: At this point we have enabled the HLP banks. That means we can
+	 * now read from the NVRAM and initialize the environment variables.
+	 * We will over-ride the env_init called in board_init_f
+	 * This is really a work-around because, the HLP bank 1
+	 * where NVRAM resides is not visible during board_init_f
+	 * (lib_ppc/board.c)
+	 * Alternatively, we could use the I2C EEPROM at start-up to configure
+	 * and enable all HLP banks and not just HLP 0 as is being done for
+	 * Taiga Rev. 2.
+	 */
+
+	env_init ();
+
+#ifndef DISABLE_PBM
+
+	/*
+	 * For IBM processors we have to set Address-Only commands generated
+	 * by PBM that are different from ones set after reset.
+	 */
+
+	temp = get_cpu_type ();
+
+	if ((CPU_750FX == temp) || (CPU_750GX == temp))
+		out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_MCMD,
+			0x00009955);
+#endif	/* DISABLE_PBM */
+
+#ifdef CONFIG_PCI
+	/*
+	 * Initialize PCI/X block
+	 */
+
+	/* Map PCI/X Configuration Space (16MB @ 0x0_FE000000) */
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
+		PCI_PFAB_BAR0_UPPER, 0);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0,
+		0xFB000001);
+	__asm__ __volatile__ ("sync");
+
+	/* Set Bus Number for the attached PCI/X bus (we will use 0 for NB) */
+
+	temp =	in32(CFG_TSI108_CSR_BASE +
+		TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT);
+
+	temp &= ~0xFF00;	/* Clear the BUS_NUM field */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT,
+		temp);
+
+	/* Map PCI/X IO Space (64KB @ 0x0_FD000000) takes one 16MB LUT entry */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO_UPPER,
+		0);
+	__asm__ __volatile__ ("sync");
+
+	/* This register is on the PCI side to interpret the address it receives
+	 * and maps it as a IO address.
+	 */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO,
+		0xFA000001);
+	__asm__ __volatile__ ("sync");
+
+	/*
+	 * Map PCI/X Memory Space
+	 *
+	 * Transactions directed from OCM to PCI Memory Space are directed
+	 * from PB to PCI
+	 * unchanged (as defined by PB_OCN_BAR1,2 and LUT settings).
+	 * If address remapping is required the corresponding PCI_PFAB_MEM32
+	 * and PCI_PFAB_PFMx register groups have to be configured.
+	 *
+	 * Map the path from the PCI/X bus into the system memory
+	 *
+	 * The memory mapped window assotiated with PCI P2O_BAR2 provides
+	 * access to the system memory without address remapping.
+	 * All system memory is opened for accesses initiated by PCI/X bus
+	 * masters.
+	 *
+	 * Initialize LUT associated with PCI P2O_BAR2
+	 *
+	 * set pointer to LUT associated with PCI P2O_BAR2
+	 */
+
+	reg_ptr =
+		(ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x500);
+
+#ifdef DISABLE_PBM
+
+	/* In case when PBM is disabled (no HW supported cache snoopng on PB)
+	 * P2O_BAR2 is directly mapped into the system memory without address
+	 * translation.
+	 */
+
+	reg_val = 0x00000004;	/* SDRAM port + NO Addr_Translation */
+
+	for (i = 0; i < 32; i++) {
+		*reg_ptr++ = reg_val;	/* P2O_BAR2_LUTx */
+		*reg_ptr++ = 0;		/* P2O_BAR2_LUT_UPPERx */
+	}
+
+	/* value for PCI BAR2 (size = 512MB, Enabled, No Addr. Translation) */
+	reg_val = 0x00007500;
+#else
+
+	reg_val = 0x00000002;	/* Destination port = PBM */
+
+	for (i = 0; i < 32; i++) {
+		*reg_ptr++ = reg_val;	/* P2O_BAR2_LUTx */
+/* P2O_BAR2_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */
+		*reg_ptr++ = 0x40000000;
+/* offset = 16MB, address translation is enabled to allow byte swapping */
+		reg_val += 0x01000000;
+	}
+
+/* value for PCI BAR2 (size = 512MB, Enabled, Address Translation Enabled) */
+	reg_val = 0x00007100;
+#endif
+
+	__asm__ __volatile__ ("eieio");
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
+		reg_val);
+	__asm__ __volatile__ ("sync");
+
+	/* Set 64-bit PCI bus address for system memory
+	 * ( 0 is the best choice for easy mapping)
+	 */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2,
+		0x00000000);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2_UPPER,
+		0x00000000);
+	__asm__ __volatile__ ("sync");
+
+#ifndef DISABLE_PBM
+	/*
+	 *  The memory mapped window assotiated with PCI P2O_BAR3 provides
+	 *  access to the system memory using SDRAM OCN port and address
+	 *  translation. This is alternative way to access SDRAM from PCI
+	 *  required for Tsi108 emulation testing.
+	 *  All system memory is opened for accesses initiated by
+	 *  PCI/X bus masters.
+	 *
+	 *  Initialize LUT associated with PCI P2O_BAR3
+	 *
+	 *  set pointer to LUT associated with PCI P2O_BAR3
+	 */
+	reg_ptr =
+		(ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x600);
+
+	reg_val = 0x00000004;	/* Destination port = SDC */
+
+	for (i = 0; i < 32; i++) {
+		*reg_ptr++ = reg_val;	/* P2O_BAR3_LUTx */
+
+/* P2O_BAR3_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */
+		*reg_ptr++ = 0;
+
+/* offset = 16MB, address translation is enabled to allow byte swapping */
+		reg_val += 0x01000000;
+	}
+
+	__asm__ __volatile__ ("eieio");
+	__asm__ __volatile__ ("sync");
+
+	/* Configure PCI P2O_BAR3 (size = 512MB, Enabled) */
+
+	reg_val =
+		in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET +
+		 PCI_P2O_PAGE_SIZES);
+	reg_val &= ~0x00FF;
+	reg_val |= 0x0071;
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES,
+		reg_val);
+	__asm__ __volatile__ ("sync");
+
+	/* Set 64-bit base PCI bus address for window (0x20000000) */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3_UPPER,
+		0x00000000);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3,
+		0x20000000);
+	__asm__ __volatile__ ("sync");
+
+#endif	/* !DISABLE_PBM */
+
+#ifdef ENABLE_PCI_CSR_BAR
+	/* open if required access to Tsi108 CSRs from the PCI/X bus */
+	/* enable BAR0 on the PCI/X bus */
+	reg_val = in32(CFG_TSI108_CSR_BASE +
+		TSI108_PCI_REG_OFFSET + PCI_MISC_CSR);
+	reg_val |= 0x02;
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR,
+		reg_val);
+	__asm__ __volatile__ ("sync");
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0_UPPER,
+		0x00000000);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0,
+		CFG_TSI108_CSR_BASE);
+	__asm__ __volatile__ ("sync");
+
+#endif
+
+	/*
+	 * Finally enable PCI/X Bus Master and Memory Space access
+	 */
+
+	reg_val = in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR);
+	reg_val |= 0x06;
+	out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val);
+	__asm__ __volatile__ ("sync");
+
+#endif	/* CONFIG_PCI */
+
+	/*
+	 * Initialize MPIC outputs (interrupt pins):
+	 * Interrupt routing on the Grendel Emul. Board:
+	 * PB_INT[0] -> INT (CPU0)
+	 * PB_INT[1] -> INT (CPU1)
+	 * PB_INT[2] -> MCP (CPU0)
+	 * PB_INT[3] -> MCP (CPU1)
+	 * Set interrupt controller outputs as Level_Sensitive/Active_Low
+	 */
+	out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(0), 0x02);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(1), 0x02);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(2), 0x02);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(3), 0x02);
+	__asm__ __volatile__ ("sync");
+
+	/*
+	 * Ensure that Machine Check exception is enabled
+	 * We need it to support PCI Bus probing (configuration reads)
+	 */
+
+	reg_val = mfmsr ();
+	mtmsr(reg_val | MSR_ME);
+
+	return 0;
+}
+
+/*
+ * Needed to print out L2 cache info
+ * used in the misc_init_r function
+ */
+
+unsigned long get_l2cr (void)
+{
+	unsigned long l2controlreg;
+	asm volatile ("mfspr %0, 1017":"=r" (l2controlreg):);
+	return l2controlreg;
+}
+
+/*
+ * misc_init_r()
+ *
+ * various things to do after relocation
+ *
+ */
+
+int misc_init_r (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+#ifdef CFG_CLK_SPREAD	/* Initialize Spread-Spectrum Clock generation */
+	ulong i;
+
+	/* Ensure that Spread-Spectrum is disabled */
+	out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, 0);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0);
+
+	/* Initialize PLL1: CG_PCI_CLK , internal OCN_CLK
+	 * Uses pre-calculated value for Fout = 800 MHz, Fs = 30 kHz, D = 0.5%
+	 */
+
+	out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
+		0x002e0044);	/* D = 0.25% */
+	out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL1,
+		0x00000039);	/* BWADJ */
+
+	/* Initialize PLL0: CG_PB_CLKO  */
+	/* Detect PB clock freq. */
+	i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS);
+	i = (i >> 16) & 0x07;	/* Get PB PLL multiplier */
+
+	out32 (CFG_TSI108_CSR_BASE +
+		TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, pll0_config[i].ctrl0);
+	out32 (CFG_TSI108_CSR_BASE +
+		TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL1, pll0_config[i].ctrl1);
+
+	/* Wait and set SSEN for both PLL0 and 1 */
+	udelay (1000);
+	out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0,
+		0x802e0044);	/* D=0.25% */
+	out32 (CFG_TSI108_CSR_BASE +
+		TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0,
+	 	0x80000000 | pll0_config[i].ctrl0);
+#endif	/* CFG_CLK_SPREAD */
+
+#ifdef CFG_L2
+	l2cache_enable ();
+#endif
+	printf ("BUS:   %d MHz\n", gd->bus_clk / 1000000);
+	printf ("MEM:   %d MHz\n", gd->mem_clk / 1000000);
+
+	/*
+	 * All the information needed to print the cache details is avaiblable
+	 * at this point i.e. above call to l2cache_enable is the very last
+	 * thing done with regards to enabling diabling the cache.
+	 * So this seems like a good place to print all this information
+	 */
+
+	printf ("CACHE: ");
+	switch (get_cpu_type()) {
+	case CPU_7447A:
+		printf ("L1 Instruction cache - 32KB 8-way");
+		(get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") :
+			printf (" DISABLED\n");
+		printf ("L1 Data cache - 32KB 8-way");
+		(get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") :
+			printf (" DISABLED\n");
+		printf ("Unified L2 cache - 512KB 8-way");
+		(get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") :
+			printf (" DISABLED\n");
+		printf ("\n");
+		break;
+
+	case CPU_7448:
+		printf ("L1 Instruction cache - 32KB 8-way");
+		(get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") :
+			printf (" DISABLED\n");
+		printf ("L1 Data cache - 32KB 8-way");
+		(get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") :
+			printf (" DISABLED\n");
+		printf ("Unified L2 cache - 1MB 8-way");
+		(get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") :
+			printf (" DISABLED\n");
+		break;
+	default:
+		break;
+	}
+	return 0;
+}

board/mpc7448hpc2/u-boot.lds

@@ -0,0 +1,136 @@
+/*
+ * (C) Copyright 2001
+ * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * u-boot.lds - linker script for U-Boot on mpc7448hpc2 Board.
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/74xx_7xx/start.o	(.text)
+
+/* store the environment in a seperate sector in the boot flash */
+/*    . = env_offset; */
+/*    common/environment.o(.text) */
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/mpc8360emds/mpc8360emds.c

@@ -31,6 +31,10 @@
 #if defined(CONFIG_OF_FLAT_TREE)
 #include <ft_build.h>
 #endif
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#include <libfdt_env.h>
+#endif
 
 const qe_iop_conf_t qe_iop_conf_tab[] = {
 	/* GETH1 */
@@ -658,22 +662,45 @@ U_BOOT_CMD(ecc, 4, 0, do_ecc,
 	   "  - disables injects\n" "  - re-inits memory");
 #endif				/* if defined(CONFIG_DDR_ECC) && defined(CONFIG_DDR_ECC_CMD) */
 
-#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+#if (defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)) \
+     && defined(CONFIG_OF_BOARD_SETUP)
+
+/*
+ * Prototypes of functions that we use.
+ */
+void ft_cpu_setup(void *blob, bd_t *bd);
+
+#ifdef CONFIG_PCI
+void ft_pci_setup(void *blob, bd_t *bd);
+#endif
+
 void
 ft_board_setup(void *blob, bd_t *bd)
 {
+#if defined(CONFIG_OF_LIBFDT)
+	int nodeoffset;
+	int tmp[2];
+
+	nodeoffset = fdt_path_offset (fdt, "/memory");
+	if (nodeoffset >= 0) {
+		tmp[0] = cpu_to_be32(bd->bi_memstart);
+		tmp[1] = cpu_to_be32(bd->bi_memsize);
+		fdt_setprop(fdt, nodeoffset, "reg", tmp, sizeof(tmp));
+	}
+#else
 	u32 *p;
 	int len;
 
-#ifdef CONFIG_PCI
-	ft_pci_setup(blob, bd);
-#endif
-	ft_cpu_setup(blob, bd);
-
 	p = ft_get_prop(blob, "/memory/reg", &len);
 	if (p != NULL) {
 		*p++ = cpu_to_be32(bd->bi_memstart);
 		*p = cpu_to_be32(bd->bi_memsize);
 	}
-}
 #endif
+
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+	ft_cpu_setup(blob, bd);
+}
+#endif /* CONFIG_OF_x */

board/mpc8360emds/pci.c

@@ -21,6 +21,10 @@
 #if defined(CONFIG_OF_FLAT_TREE)
 #include <ft_build.h>
 #endif
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#include <libfdt_env.h>
+#endif
 
 #include <asm/fsl_i2c.h>
 
@@ -299,6 +303,22 @@ void pci_init_board(void)
 }
 #endif				/* CONFIG_PCISLAVE */
 
+#if defined(CONFIG_OF_LIBFDT)
+void
+ft_pci_setup(void *blob, bd_t *bd)
+{
+	int nodeoffset;
+	int err;
+	int tmp[2];
+
+	nodeoffset = fdt_path_offset (fdt, "/" OF_SOC "/pci@8500");
+	if (nodeoffset >= 0) {
+		tmp[0] = cpu_to_be32(hose[0].first_busno);
+		tmp[1] = cpu_to_be32(hose[0].last_busno);
+		err = fdt_setprop(fdt, nodeoffset, "bus-range", tmp, sizeof(tmp));
+	}
+}
+#endif				/* CONFIG_OF_LIBFDT */
 #ifdef CONFIG_OF_FLAT_TREE
 void
 ft_pci_setup(void *blob, bd_t *bd)

board/mpc8641hpcn/Makefile

@@ -25,7 +25,9 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= $(BOARD).o pixis.o sys_eeprom.o
+COBJS	:= $(BOARD).o sys_eeprom.o \
+		../freescale/common/pixis.o
+
 SOBJS	:= init.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)

board/mpc8641hpcn/mpc8641hpcn.c

@@ -1,9 +1,5 @@
 /*
- * Copyright 2004 Freescale Semiconductor.
- * Jeff Brown
- * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ * Copyright 2006, 2007 Freescale Semiconductor.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -25,18 +21,18 @@
  */
 
 #include <common.h>
-#include <command.h>
 #include <pci.h>
 #include <asm/processor.h>
 #include <asm/immap_86xx.h>
 #include <spd.h>
+#include <asm/io.h>
 
 #if defined(CONFIG_OF_FLAT_TREE)
 #include <ft_build.h>
 extern void ft_cpu_setup(void *blob, bd_t *bd);
 #endif
 
-#include "pixis.h"
+#include "../freescale/common/pixis.h"
 
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
 extern void ddr_enable_ecc(unsigned int dram_size);
@@ -258,109 +254,6 @@ ft_board_setup(void *blob, bd_t *bd)
 #endif
 
 
-void
-mpc8641_reset_board(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
-{
-	char cmd;
-	ulong val;
-	ulong corepll;
-
-	/*
-	 * No args is a simple reset request.
-	 */
-	if (argc <= 1) {
-		out8(PIXIS_BASE + PIXIS_RST, 0);
-		/* not reached */
-	}
-
-	cmd = argv[1][1];
-	switch (cmd) {
-	case 'f':		/* reset with frequency changed */
-		if (argc < 5)
-			goto my_usage;
-		read_from_px_regs(0);
-
-		val = set_px_sysclk(simple_strtoul(argv[2], NULL, 10));
-
-		corepll = strfractoint(argv[3]);
-		val = val + set_px_corepll(corepll);
-		val = val + set_px_mpxpll(simple_strtoul(argv[4], NULL, 10));
-		if (val == 3) {
-			puts("Setting registers VCFGEN0 and VCTL\n");
-			read_from_px_regs(1);
-			puts("Resetting board with values from VSPEED0, VSPEED1, VCLKH, and VCLKL ....\n");
-			set_px_go();
-		} else
-			goto my_usage;
-
-		while (1) ;	/* Not reached */
-
-	case 'l':
-		if (argv[2][1] == 'f') {
-			read_from_px_regs(0);
-			read_from_px_regs_altbank(0);
-			/* reset with frequency changed */
-			val = set_px_sysclk(simple_strtoul(argv[3], NULL, 10));
-
-			corepll = strfractoint(argv[4]);
-			val = val + set_px_corepll(corepll);
-			val = val + set_px_mpxpll(simple_strtoul(argv[5],
-								 NULL, 10));
-			if (val == 3) {
-				puts("Setting registers VCFGEN0, VCFGEN1, VBOOT, and VCTL\n");
-				set_altbank();
-				read_from_px_regs(1);
-				read_from_px_regs_altbank(1);
-				puts("Enabling watchdog timer on the FPGA and resetting board with values from VSPEED0, VSPEED1, VCLKH, and VCLKL to boot from the other bank ....\n");
-				set_px_go_with_watchdog();
-			} else
-				goto my_usage;
-
-			while (1) ;	/* Not reached */
-
-		} else if (argv[2][1] == 'd') {
-			/*
-			 * Reset from alternate bank without changing
-			 * frequencies but with watchdog timer enabled.
-			 */
-			read_from_px_regs(0);
-			read_from_px_regs_altbank(0);
-			puts("Setting registers VCFGEN1, VBOOT, and VCTL\n");
-			set_altbank();
-			read_from_px_regs_altbank(1);
-			puts("Enabling watchdog timer on the FPGA and resetting board to boot from the other bank....\n");
-			set_px_go_with_watchdog();
-			while (1) ;	/* Not reached */
-
-		} else {
-			/*
-			 * Reset from next bank without changing
-			 * frequency and without watchdog timer enabled.
-			 */
-			read_from_px_regs(0);
-			read_from_px_regs_altbank(0);
-			if (argc > 2)
-				goto my_usage;
-			puts("Setting registers VCFGNE1, VBOOT, and VCTL\n");
-			set_altbank();
-			read_from_px_regs_altbank(1);
-			puts("Resetting board to boot from the other bank....\n");
-			set_px_go();
-		}
-
-	default:
-		goto my_usage;
-	}
-
-my_usage:
-	puts("\nUsage: reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>\n");
-	puts("       reset altbank [cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>]\n");
-	puts("       reset altbank [wd]\n");
-	puts("For example:   reset cf 40 2.5 10\n");
-	puts("See MPC8641HPCN Design Workbook for valid values of command line parameters.\n");
-}
-
-
 /*
  * get_board_sys_clk
  *      Reads the FPGA on board for CONFIG_SYS_CLK_FREQ

board/nc650/config.mk

@@ -1,5 +1,5 @@
 #
-# (C) Copyright 2006 Detlev Zundel, dzu@denx.de
+# (C) Copyright 2006, 2007 Detlev Zundel, dzu@denx.de
 # (C) Copyright 2004
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
@@ -27,4 +27,3 @@
 #
 
 TEXT_BASE = 0x40700000
-BOARDLIBS = $(obj)drivers/nand/libnand.a

board/nc650/nc650.c

@@ -177,16 +177,14 @@ long int initdram (int board_type)
 	 *
 	 * try 8 column mode
 	 */
-	size8 = dram_size (CFG_MAMR_8COL, (ulong *) SDRAM_BASE3_PRELIM,
-					   SDRAM_MAX_SIZE);
+	size8 = dram_size (CFG_MAMR_8COL, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
 
 	udelay (1000);
 
 	/*
 	 * try 9 column mode
 	 */
-	size9 = dram_size (CFG_MAMR_9COL, (ulong *) SDRAM_BASE3_PRELIM,
-					  SDRAM_MAX_SIZE);
+	size9 = dram_size (CFG_MAMR_9COL, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
 
 	udelay (1000);
 

board/uc101/uc101.c

@@ -221,6 +221,8 @@ long int initdram (int board_type)
 int checkboard (void)
 {
 	puts ("Board: MAN UC101\n");
+	/* clear the Display */
+	*(char *)(CFG_DISP_CWORD) = 0x80;
 	return 0;
 }
 

board/xilinx/ml401/Makefile

@@ -0,0 +1,65 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+$(shell mkdir -p $(obj)../xilinx_enet)
+endif
+
+INCS		:= -I../common -I../xilinx_enet
+CFLAGS		+= $(INCS)
+HOST_CFLAGS	+= $(INCS)
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	= $(BOARD).o \
+	  ../xilinx_enet/emac_adapter.o  ../xilinx_enet/xemac.o \
+	  ../xilinx_enet/xemac_options.o ../xilinx_enet/xemac_polled.o \
+	  ../xilinx_enet/xemac_intr.o ../xilinx_enet/xemac_g.o \
+	  ../xilinx_enet/xemac_intr_dma.o ../common/xipif_v1_23_b.o \
+	  ../common/xbasic_types.o ../common/xdma_channel.o \
+	  ../common/xdma_channel_sg.o ../common/xpacket_fifo_v1_00_b.o \
+	  ../common/xversion.o \
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/xilinx/ml401/config.mk

@@ -0,0 +1,32 @@
+#
+# (C) Copyright 2007 Michal Simek
+#
+# Michal  SIMEK <monstr@monstr.eu>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# CAUTION: This file is automatically generated by libgen.
+# Version: Xilinx EDK 6.3 EDK_Gmm.12.3
+#
+
+TEXT_BASE = 0x12000000
+
+PLATFORM_CPPFLAGS += -mno-xl-soft-mul
+PLATFORM_CPPFLAGS += -mno-xl-soft-div
+PLATFORM_CPPFLAGS += -mxl-barrel-shift

board/xilinx/ml401/ml401.c

@@ -0,0 +1,49 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal  SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This is a board specific file.  It's OK to include board specific
+ * header files */
+
+#include <common.h>
+#include <config.h>
+
+void do_reset (void)
+{
+#ifdef CFG_GPIO_0
+	*((unsigned long *)(CFG_GPIO_0_ADDR)) =
+	    ++(*((unsigned long *)(CFG_GPIO_0_ADDR)));
+#endif
+#ifdef CFG_RESET_ADDRESS
+	puts ("Reseting board\n");
+	asm ("bra r0");
+#endif
+}
+
+int gpio_init (void)
+{
+#ifdef CFG_GPIO_0
+	*((unsigned long *)(CFG_GPIO_0_ADDR)) = 0x0;
+#endif
+	return 0;
+}

board/xilinx/ml401/u-boot.lds

@@ -0,0 +1,67 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(microblaze)
+ENTRY(_start)
+
+SECTIONS
+{
+	.text ALIGN(0x4):
+	{
+		__text_start = .;
+		cpu/microblaze/start.o (.text)
+		*(.text)
+		__text_end = .;
+	}
+
+	.rodata ALIGN(0x4):
+	{
+		__rodata_start = .;
+		*(.rodata)
+		__rodata_end = .;
+	}
+
+	.data ALIGN(0x4):
+	{
+		__data_start = .;
+		*(.data)
+		__data_end = .;
+	}
+
+	.u_boot_cmd ALIGN(0x4):
+	{
+		. = .;
+		__u_boot_cmd_start = .;
+		*(.u_boot_cmd)
+		__u_boot_cmd_end = .;
+	}
+
+	.bss ALIGN(0x4):
+	{
+		__bss_start = .;
+		*(.bss)
+		__bss_end = .;
+	}
+	__end = . ;
+}

board/xilinx/ml401/xparameters.h

@@ -0,0 +1,67 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal  SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ *
+ * CAUTION: This file is automatically generated by libgen.
+ * Version: Xilinx EDK 6.3 EDK_Gmm.12.3
+ */
+
+/* System Clock Frequency */
+#define XILINX_CLOCK_FREQ	66666667
+
+/* Interrupt controller is intc_0 */
+#define XILINX_INTC_BASEADDR	0xd1000fc0
+#define XILINX_INTC_NUM_INTR_INPUTS	12
+
+/* Timer pheriphery is opb_timer_0 */
+#define XILINX_TIMER_BASEADDR	0xa2000000
+#define XILINX_TIMER_IRQ	0
+
+/* Uart pheriphery is console_uart */
+#define XILINX_UART_BASEADDR	0xa0000000
+#define XILINX_UART_BAUDRATE	115200
+
+/* GPIO is opb_gpio_0*/
+#define XILINX_GPIO_BASEADDR	0x90000000
+
+/* Flash Memory is opb_emc_0 */
+#define XILINX_FLASH_START	0x28000000
+#define XILINX_FLASH_SIZE	0x00800000
+
+/* Main Memory is plb_ddr_0 */
+#define XILINX_RAM_START	0x10000000
+#define XILINX_RAM_SIZE	0x10000000
+
+/* Sysace Controller is opb_sysace_0 */
+#define XILINX_SYSACE_BASEADDR	0xCF000000
+#define XILINX_SYSACE_HIGHADDR	0xCF0001FF
+#define XILINX_SYSACE_MEM_WIDTH	16
+
+/* Ethernet controller is opb_ethernet_0 */
+#define XPAR_XEMAC_NUM_INSTANCES	1
+#define XPAR_OPB_ETHERNET_0_DEVICE_ID	0
+#define XPAR_OPB_ETHERNET_0_BASEADDR	0x60000000
+#define XPAR_OPB_ETHERNET_0_HIGHADDR	0x60003FFF
+#define XPAR_OPB_ETHERNET_0_DMA_PRESENT	1
+#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST	1
+#define XPAR_OPB_ETHERNET_0_MII_EXIST	1

board/xilinx/xilinx_enet/emac_adapter.c

@@ -147,7 +147,11 @@ eth_rx(void)
 	RecvFrameLength = PKTSIZE;
 	Result = XEmac_PollRecv(&Emac, (u8 *) etherrxbuff, &RecvFrameLength);
 	if (Result == XST_SUCCESS) {
+#ifndef CONFIG_EMACLITE
 		NetReceive((uchar *)etherrxbuff, RecvFrameLength);
+#else
+		NetReceive(etherrxbuff, RecvFrameLength);
+#endif
 		return (1);
 	} else {
 		return (0);

board/xilinx/xupv2p/Makefile

@@ -0,0 +1,65 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+$(shell mkdir -p $(obj)../xilinx_enet)
+endif
+
+INCS		:= -I../common -I../xilinx_enet
+CFLAGS		+= $(INCS)
+HOST_CFLAGS	+= $(INCS)
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	= $(BOARD).o \
+	  ../xilinx_enet/emac_adapter.o  ../xilinx_enet/xemac.o \
+	  ../xilinx_enet/xemac_options.o ../xilinx_enet/xemac_polled.o \
+	  ../xilinx_enet/xemac_intr.o ../xilinx_enet/xemac_g.o \
+	  ../xilinx_enet/xemac_intr_dma.o ../common/xipif_v1_23_b.o \
+	  ../common/xbasic_types.o ../common/xdma_channel.o \
+	  ../common/xdma_channel_sg.o ../common/xpacket_fifo_v1_00_b.o \
+	  ../common/xversion.o \
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/xilinx/xupv2p/config.mk

@@ -0,0 +1,32 @@
+#
+# (C) Copyright 2007 Michal Simek
+#
+# Michal  SIMEK <monstr@monstr.eu>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# CAUTION: This file is automatically generated by libgen.
+# Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
+#
+
+TEXT_BASE = 0x38000000
+
+PLATFORM_CPPFLAGS += -mno-xl-soft-mul
+PLATFORM_CPPFLAGS += -mno-xl-soft-div
+PLATFORM_CPPFLAGS += -mxl-barrel-shift

board/xilinx/xupv2p/u-boot.lds

@@ -0,0 +1,67 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(microblaze)
+ENTRY(_start)
+
+SECTIONS
+{
+	.text ALIGN(0x4):
+	{
+		__text_start = .;
+		cpu/microblaze/start.o (.text)
+		*(.text)
+		__text_end = .;
+	}
+
+	.rodata ALIGN(0x4):
+	{
+		__rodata_start = .;
+		*(.rodata)
+		__rodata_end = .;
+	}
+
+	.data ALIGN(0x4):
+	{
+		__data_start = .;
+		*(.data)
+		__data_end = .;
+	}
+
+	.u_boot_cmd ALIGN(0x4):
+	{
+		. = .;
+		__u_boot_cmd_start = .;
+		*(.u_boot_cmd)
+		__u_boot_cmd_end = .;
+	}
+
+	.bss ALIGN(0x4):
+	{
+		__bss_start = .;
+		*(.bss)
+		__bss_end = .;
+	}
+	__end = . ;
+}

board/xilinx/xupv2p/xparameters.h

@@ -0,0 +1,64 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal  SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * CAUTION: This file is automatically generated by libgen.
+ * Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
+ */
+
+/* System Clock Frequency */
+#define XILINX_CLOCK_FREQ	100000000
+
+/* Interrupt controller is opb_intc_0 */
+#define XILINX_INTC_BASEADDR	0x41200000
+#define XILINX_INTC_NUM_INTR_INPUTS	11
+
+/* Timer pheriphery is opb_timer_1 */
+#define XILINX_TIMER_BASEADDR	0x41c00000
+#define XILINX_TIMER_IRQ	1
+
+/* Uart pheriphery is RS232_Uart_1 */
+#define XILINX_UART_BASEADDR	0x40600000
+#define XILINX_UART_BAUDRATE	115200
+
+/* GPIO is LEDs_4Bit*/
+#define XILINX_GPIO_BASEADDR	0x40000000
+
+/* FLASH doesn't exist none */
+
+/* Main Memory is DDR_256MB_32MX64_rank1_row13_col10_cl2_5 */
+#define XILINX_RAM_START	0x30000000
+#define XILINX_RAM_SIZE	0x10000000
+
+/* Sysace Controller is SysACE_CompactFlash */
+#define XILINX_SYSACE_BASEADDR	0x41800000
+#define XILINX_SYSACE_HIGHADDR	0x4180ffff
+#define XILINX_SYSACE_MEM_WIDTH	16
+
+/* Ethernet controller is Ethernet_MAC */
+#define XPAR_XEMAC_NUM_INSTANCES	1
+#define XPAR_OPB_ETHERNET_0_DEVICE_ID	0
+#define XPAR_OPB_ETHERNET_0_BASEADDR	0x40c00000
+#define XPAR_OPB_ETHERNET_0_HIGHADDR	0x40c0ffff
+#define XPAR_OPB_ETHERNET_0_DMA_PRESENT	1
+#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST	1
+#define XPAR_OPB_ETHERNET_0_MII_EXIST	1

board/xilinx/xupv2p/xupv2p.c

@@ -0,0 +1,49 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal  SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This is a board specific file.  It's OK to include board specific
+ * header files */
+
+#include <common.h>
+#include <config.h>
+
+void do_reset (void)
+{
+#ifdef CFG_GPIO_0
+	*((unsigned long *)(CFG_GPIO_0_ADDR)) =
+	    ++(*((unsigned long *)(CFG_GPIO_0_ADDR)));
+#endif
+#ifdef CFG_RESET_ADDRESS
+	puts ("Reseting board\n");
+	asm ("bra r0");
+#endif
+}
+
+int gpio_init (void)
+{
+#ifdef CFG_GPIO_0
+	*((unsigned long *)(CFG_GPIO_0_ADDR)) = 0x0;
+#endif
+	return 0;
+}

common/Makefile

@@ -32,7 +32,7 @@ COBJS	= main.o ACEX1K.o altera.o bedbug.o circbuf.o cmd_autoscript.o \
 	  cmd_cache.o cmd_console.o \
 	  cmd_date.o cmd_dcr.o cmd_diag.o cmd_display.o cmd_doc.o cmd_dtt.o \
 	  cmd_eeprom.o cmd_elf.o cmd_ext2.o \
-	  cmd_fat.o cmd_fdc.o cmd_fdos.o cmd_flash.o cmd_fpga.o \
+	  cmd_fat.o cmd_fdc.o cmd_fdt.o cmd_fdos.o cmd_flash.o cmd_fpga.o \
 	  cmd_i2c.o cmd_ide.o cmd_immap.o cmd_itest.o cmd_jffs2.o \
 	  cmd_load.o cmd_log.o \
 	  cmd_mem.o cmd_mii.o cmd_misc.o cmd_mmc.o \
@@ -45,7 +45,7 @@ COBJS	= main.o ACEX1K.o altera.o bedbug.o circbuf.o cmd_autoscript.o \
 	  env_nand.o env_dataflash.o env_flash.o env_eeprom.o \
 	  env_nvram.o env_nowhere.o \
 	  exports.o \
-	  flash.o fpga.o ft_build.o \
+	  fdt_support.o flash.o fpga.o ft_build.o \
 	  hush.o kgdb.o lcd.o lists.o lynxkdi.o \
 	  memsize.o miiphybb.o miiphyutil.o \
 	  s_record.o serial.o soft_i2c.o soft_spi.o spartan2.o spartan3.o \

common/cmd_bdinfo.c

@@ -180,6 +180,32 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 	return 0;
 }
+#elif defined(CONFIG_MICROBLAZE) /* ! PPC, which leaves Microblaze */
+
+int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	int i;
+	bd_t *bd = gd->bd;
+	print_num ("mem start      ",	(ulong)bd->bi_memstart);
+	print_num ("mem size       ",	(ulong)bd->bi_memsize);
+	print_num ("flash start    ",	(ulong)bd->bi_flashstart);
+	print_num ("flash size     ",	(ulong)bd->bi_flashsize);
+	print_num ("flash offset   ",	(ulong)bd->bi_flashoffset);
+#if defined(CFG_SRAM_BASE)
+	print_num ("sram start     ",	(ulong)bd->bi_sramstart);
+	print_num ("sram size      ",	(ulong)bd->bi_sramsize);
+#endif
+#if defined(CFG_CMD_NET)
+	puts ("ethaddr     =");
+	for (i=0; i<6; ++i) {
+		printf ("%c%02X", i ? ':' : ' ', bd->bi_enetaddr[i]);
+	}
+	puts ("\nip_addr     = ");
+	print_IPaddr (bd->bi_ip_addr);
+#endif
+	printf ("\nbaudrate    = %d bps\n", (ulong)bd->bi_baudrate);
+	return 0;
+}
 
 #else /* ! PPC, which leaves MIPS */
 

common/cmd_bootm.c

@@ -34,7 +34,12 @@
 #include <environment.h>
 #include <asm/byteorder.h>
 
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_LIBFDT)
+#include <fdt.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#endif
+#if defined(CONFIG_OF_FLAT_TREE)
 #include <ft_build.h>
 #endif
 
@@ -467,7 +472,7 @@ U_BOOT_CMD(
  	"[addr [arg ...]]\n    - boot application image stored in memory\n"
  	"\tpassing arguments 'arg ...'; when booting a Linux kernel,\n"
  	"\t'arg' can be the address of an initrd image\n"
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
 	"\tWhen booting a Linux kernel which requires a flat device-tree\n"
 	"\ta third argument is required which is the address of the of the\n"
 	"\tdevice-tree blob. To boot that kernel without an initrd image,\n"
@@ -529,7 +534,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 	bd_t	*kbd;
 	void	(*kernel)(bd_t *, ulong, ulong, ulong, ulong);
 	image_header_t *hdr = &header;
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
 	char	*of_flat_tree = NULL;
 	ulong	of_data = 0;
 #endif
@@ -622,7 +627,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 	 * Check if there is an initrd image
 	 */
 
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
 	/* Look for a '-' which indicates to ignore the ramdisk argument */
 	if (argc >= 3 && strcmp(argv[2], "-") ==  0) {
 			debug ("Skipping initrd\n");
@@ -739,12 +744,15 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 		len = data = 0;
 	}
 
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
 	if(argc > 3) {
 		of_flat_tree = (char *) simple_strtoul(argv[3], NULL, 16);
 		hdr = (image_header_t *)of_flat_tree;
-
-		if  (*(ulong *)of_flat_tree == OF_DT_HEADER) {
+#if defined(CONFIG_OF_LIBFDT)
+		if (fdt_check_header(of_flat_tree) == 0) {
+#else
+		if (*(ulong *)of_flat_tree == OF_DT_HEADER) {
+#endif
 #ifndef CFG_NO_FLASH
 			if (addr2info((ulong)of_flat_tree) != NULL)
 				of_data = (ulong)of_flat_tree;
@@ -787,7 +795,11 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 				printf("ERROR: uImage is not uncompressed\n");
 				return;
 			}
+#if defined(CONFIG_OF_LIBFDT)
+			if (fdt_check_header(of_flat_tree + sizeof(image_header_t)) == 0) {
+#else
 			if (*((ulong *)(of_flat_tree + sizeof(image_header_t))) != OF_DT_HEADER) {
+#endif
 				printf ("ERROR: uImage data is not a flat device tree\n");
 				return;
 			}
@@ -824,12 +836,20 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 			of_data += 4 - tail;
 		}
 
+#if defined(CONFIG_OF_LIBFDT)
+		if (fdt_check_header((void *)of_data) != 0) {
+#else
 		if (((struct boot_param_header *)of_data)->magic != OF_DT_HEADER) {
+#endif
 			printf ("ERROR: image is not a flat device tree\n");
 			return;
 		}
 
+#if defined(CONFIG_OF_LIBFDT)
+		if (be32_to_cpu(fdt_totalsize(of_data)) !=  ntohl(len_ptr[2])) {
+#else
 		if (((struct boot_param_header *)of_data)->totalsize != ntohl(len_ptr[2])) {
+#endif
 			printf ("ERROR: flat device tree size does not agree with image\n");
 			return;
 		}
@@ -913,7 +933,52 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 	unlock_ram_in_cache();
 #endif
 
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_LIBFDT)
+	/* move of_flat_tree if needed */
+	if (of_data) {
+		int err;
+		ulong of_start, of_len;
+
+		of_len = be32_to_cpu(fdt_totalsize(of_data));
+		/* position on a 4K boundary before the initrd/kbd */
+		if (initrd_start)
+			of_start = initrd_start - of_len;
+		else
+			of_start  = (ulong)kbd - of_len;
+		of_start &= ~(4096 - 1);	/* align on page */
+		debug ("## device tree at 0x%08lX ... 0x%08lX (len=%ld=0x%lX)\n",
+			of_data, of_data + of_len - 1, of_len, of_len);
+
+		of_flat_tree = (char *)of_start;
+		printf ("   Loading Device Tree to %08lx, end %08lx ... ",
+			of_start, of_start + of_len - 1);
+		err = fdt_open_into((void *)of_start, (void *)of_data, of_len);
+		if (err != 0) {
+			printf ("libfdt: %s " __FILE__ " %d\n", fdt_strerror(err), __LINE__);
+		}
+		/*
+		 * Add the chosen node if it doesn't exist, add the env and bd_t
+		 * if the user wants it (the logic is in the subroutines).
+		 */
+		if (fdt_chosen(of_flat_tree, initrd_start, initrd_end, 0) < 0) {
+				printf("Failed creating the /chosen node (0x%08X), aborting.\n", of_flat_tree);
+				return;
+		}
+#ifdef CONFIG_OF_HAS_UBOOT_ENV
+		if (fdt_env(of_flat_tree) < 0) {
+				printf("Failed creating the /u-boot-env node, aborting.\n");
+				return;
+		}
+#endif
+#ifdef CONFIG_OF_HAS_BD_T
+		if (fdt_bd_t(of_flat_tree) < 0) {
+				printf("Failed creating the /bd_t node, aborting.\n");
+				return;
+		}
+#endif
+	}
+#endif
+#if defined(CONFIG_OF_FLAT_TREE)
 	/* move of_flat_tree if needed */
 	if (of_data) {
 		ulong of_start, of_len;
@@ -942,13 +1007,13 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 	 *   r6: Start of command line string
 	 *   r7: End   of command line string
 	 */
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
 	if (!of_flat_tree)	/* no device tree; boot old style */
 #endif
 		(*kernel) (kbd, initrd_start, initrd_end, cmd_start, cmd_end);
 		/* does not return */
 
-#ifdef CONFIG_OF_FLAT_TREE
+#if defined(CONFIG_OF_FLAT_TREE) || defined(CONFIG_OF_LIBFDT)
 	/*
 	 * Linux Kernel Parameters (passing device tree):
 	 *   r3: ptr to OF flat tree, followed by the board info data
@@ -957,8 +1022,28 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 	 *   r6: NULL
 	 *   r7: NULL
 	 */
+#if defined(CONFIG_OF_FLAT_TREE)
 	ft_setup(of_flat_tree, kbd, initrd_start, initrd_end);
 	/* ft_dump_blob(of_flat_tree); */
+#endif
+#if defined(CONFIG_OF_LIBFDT)
+	if (fdt_chosen(of_flat_tree, initrd_start, initrd_end, 0) < 0) {
+		printf("Failed creating the /chosen node (0x%08X), aborting.\n", of_flat_tree);
+		return;
+	}
+#ifdef CONFIG_OF_HAS_UBOOT_ENV
+	if (fdt_env(of_flat_tree) < 0) {
+		printf("Failed creating the /u-boot-env node, aborting.\n");
+		return;
+	}
+#endif
+#ifdef CONFIG_OF_HAS_BD_T
+	if (fdt_bd_t(of_flat_tree) < 0) {
+		printf("Failed creating the /bd_t node, aborting.\n");
+		return;
+	}
+#endif
+#endif /* if defined(CONFIG_OF_LIBFDT) */
 
 	(*kernel) ((bd_t *)of_flat_tree, (ulong)kernel, 0, 0, 0);
 #endif

common/cmd_fdt.c

@@ -0,0 +1,635 @@
+/*
+ * (C) Copyright 2007
+ * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com
+ * Based on code written by:
+ *   Pantelis Antoniou <pantelis.antoniou@gmail.com> and
+ *   Matthew McClintock <msm@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <linux/ctype.h>
+#include <linux/types.h>
+
+#ifdef CONFIG_OF_LIBFDT
+
+#include <asm/global_data.h>
+#include <fdt.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+
+#define MAX_LEVEL	32		/* how deeply nested we will go */
+#define SCRATCHPAD	1024	/* bytes of scratchpad memory */
+
+/*
+ * Global data (for the gd->bd)
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Scratchpad memory.
+ */
+static char data[SCRATCHPAD];
+
+
+/*
+ * Function prototypes/declarations.
+ */
+static int fdt_valid(void);
+static void print_data(const void *data, int len);
+
+
+/*
+ * Flattened Device Tree command, see the help for parameter definitions.
+ */
+int do_fdt (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+	char		op;
+
+	if (argc < 2) {
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	/*
+	 * Figure out which subcommand was given
+	 */
+	op = argv[1][0];
+	/********************************************************************
+	 * Set the address of the fdt
+	 ********************************************************************/
+	if (op == 'a') {
+		/*
+		 * Set the address [and length] of the fdt.
+		 */
+		fdt = (struct fdt_header *)simple_strtoul(argv[2], NULL, 16);
+
+		if (!fdt_valid()) {
+			return 1;
+		}
+
+		if (argc >= 4) {
+			int  len;
+			int  err;
+			/*
+			 * Optional new length
+			 */
+			len =  simple_strtoul(argv[3], NULL, 16);
+			if (len < fdt_totalsize(fdt)) {
+				printf ("New length %d < existing length %d, ignoring.\n",
+					len, fdt_totalsize(fdt));
+			} else {
+				/*
+				 * Open in place with a new length.
+				 */
+				err = fdt_open_into(fdt, fdt, len);
+				if (err != 0) {
+					printf ("libfdt: %s\n", fdt_strerror(err));
+				}
+			}
+		}
+
+	/********************************************************************
+	 * Move the fdt
+	 ********************************************************************/
+	} else if (op == 'm') {
+		struct fdt_header *newaddr;
+		int  len;
+		int  err;
+
+		if (argc != 5) {
+			printf ("Usage:\n%s\n", cmdtp->usage);
+			return 1;
+		}
+
+		/*
+		 * Set the address and length of the fdt.
+		 */
+		fdt = (struct fdt_header *)simple_strtoul(argv[2], NULL, 16);
+		if (!fdt_valid()) {
+			return 1;
+		}
+
+		newaddr = (struct fdt_header *)simple_strtoul(argv[3], NULL, 16);
+		len     =  simple_strtoul(argv[4], NULL, 16);
+		if (len < fdt_totalsize(fdt)) {
+			printf ("New length %d < existing length %d, aborting.\n",
+				len, fdt_totalsize(fdt));
+			return 1;
+		}
+
+		/*
+		 * Copy to the new location.
+		 */
+		err = fdt_open_into(fdt, newaddr, len);
+		if (err != 0) {
+			printf ("libfdt: %s\n", fdt_strerror(err));
+			return 1;
+		}
+		fdt = newaddr;
+
+	/********************************************************************
+	 * Set the value of a node in the fdt.
+	 ********************************************************************/
+	} else if (op == 's') {
+		char *pathp;		/* path */
+		char *prop;			/* property */
+		struct fdt_property *nodep;	/* node struct pointer */
+		char *newval;		/* value from the user (as a string) */
+		char *vp;			/* temporary value pointer */
+		char *cp;			/* temporary char pointer */
+		int  nodeoffset;	/* node offset from libfdt */
+		int  len;			/* new length of the property */
+		int  oldlen;		/* original length of the property */
+		unsigned long tmp;	/* holds converted values */
+		int  ret;			/* return value */
+
+		/*
+		 * Parameters: Node path, property, value.
+		 */
+		if (argc < 5) {
+			printf ("Usage:\n%s\n", cmdtp->usage);
+			return 1;
+		}
+
+		pathp  = argv[2];
+		prop   = argv[3];
+		newval = argv[4];
+
+		if (strcmp(pathp, "/") == 0) {
+			nodeoffset = 0;
+		} else {
+			nodeoffset = fdt_path_offset (fdt, pathp);
+			if (nodeoffset < 0) {
+				/*
+			 	 * Not found or something else bad happened.
+			 	 */
+				printf ("libfdt: %s\n", fdt_strerror(nodeoffset));
+				return 1;
+			}
+		}
+		nodep = fdt_getprop (fdt, nodeoffset, prop, &oldlen);
+		if (oldlen < 0) {
+			printf ("libfdt %s\n", fdt_strerror(oldlen));
+			return 1;
+		} else if (oldlen == 0) {
+			/*
+			 * The specified property has no value
+			 */
+			printf("%s has no value, cannot set one (yet).\n", prop);
+			return 1;
+		} else {
+			/*
+			 * Convert the new property
+			 */
+			vp = data;
+			if (*newval == '<') {
+				/*
+				 * Bigger values than bytes.
+				 */
+				len = 0;
+				newval++;
+				while ((*newval != '>') && (*newval != '\0')) {
+					cp = newval;
+					tmp = simple_strtoul(cp, &newval, 16);
+					if ((newval - cp) <= 2) {
+						*vp = tmp & 0xFF;
+						vp  += 1;
+						len += 1;
+					} else if ((newval - cp) <= 4) {
+						*(uint16_t *)vp = __cpu_to_be16(tmp);
+						vp  += 2;
+						len += 2;
+					} else if ((newval - cp) <= 8) {
+						*(uint32_t *)vp = __cpu_to_be32(tmp);
+						vp  += 4;
+						len += 4;
+					} else {
+						printf("Sorry, I could not convert \"%s\"\n", cp);
+						return 1;
+					}
+					while (*newval == ' ')
+						newval++;
+				}
+				if (*newval != '>') {
+					printf("Unexpected character '%c'\n", *newval);
+					return 1;
+				}
+			} else if (*newval == '[') {
+				/*
+				 * Byte stream.  Convert the values.
+				 */
+				len = 0;
+				newval++;
+				while ((*newval != ']') && (*newval != '\0')) {
+					tmp = simple_strtoul(newval, &newval, 16);
+					*vp++ = tmp & 0xFF;
+					len++;
+					while (*newval == ' ')
+						newval++;
+				}
+				if (*newval != ']') {
+					printf("Unexpected character '%c'\n", *newval);
+					return 1;
+				}
+			} else {
+				/*
+				 * Assume it is a string.  Copy it into our data area for
+				 * convenience (including the terminating '\0').
+				 */
+				len = strlen(newval) + 1;
+				strcpy(data, newval);
+			}
+
+			ret = fdt_setprop(fdt, nodeoffset, prop, data, len);
+			if (ret < 0) {
+				printf ("libfdt %s\n", fdt_strerror(ret));
+				return 1;
+			}
+		}
+
+	/********************************************************************
+	 * Print (recursive) / List (single level)
+	 ********************************************************************/
+	} else if ((op == 'p') || (op == 'l')) {
+		/*
+		 * Recursively print (a portion of) the fdt.
+		 */
+		static int offstack[MAX_LEVEL];
+		static char tabs[MAX_LEVEL+1] = "\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t";
+		int depth = MAX_LEVEL;	/* how deep to print */
+		char *pathp;		/* path */
+		char *prop;			/* property */
+		void *nodep;		/* property node pointer */
+		int  nodeoffset;	/* node offset from libfdt */
+		int  nextoffset;	/* next node offset from libfdt */
+		uint32_t tag;		/* tag */
+		int  len;			/* length of the property */
+		int  level = 0;		/* keep track of nesting level */
+
+		/*
+		 * list is an alias for print, but limited to 1 level
+		 */
+		if (op == 'l') {
+			depth = 1;
+		}
+
+		/*
+		 * Get the starting path.  The root node is an oddball,
+		 * the offset is zero and has no name.
+		 */
+		pathp = argv[2];
+		if (argc > 3)
+			prop = argv[3];
+		else
+			prop = NULL;
+
+		if (strcmp(pathp, "/") == 0) {
+			nodeoffset = 0;
+			printf("/");
+		} else {
+			nodeoffset = fdt_path_offset (fdt, pathp);
+			if (nodeoffset < 0) {
+				/*
+				 * Not found or something else bad happened.
+				 */
+				printf ("libfdt %s\n", fdt_strerror(nodeoffset));
+				return 1;
+			}
+		}
+		/*
+		 * The user passed in a property as well as node path.  Print only
+		 * the given property and then return.
+		 */
+		if (prop) {
+			nodep = fdt_getprop (fdt, nodeoffset, prop, &len);
+			if (len == 0) {
+				printf("%s %s\n", pathp, prop);	/* no property value */
+				return 0;
+			} else if (len > 0) {
+				printf("%s=", prop);
+				print_data (nodep, len);
+				printf("\n");
+				return 0;
+			} else {
+				printf ("libfdt %s\n", fdt_strerror(len));
+				return 1;
+			}
+		}
+
+		/*
+		 * The user passed in a node path and no property, print the node
+		 * and all subnodes.
+		 */
+		offstack[0] = nodeoffset;
+
+		while(level >= 0) {
+			tag = fdt_next_tag(fdt, nodeoffset, &nextoffset, &pathp);
+			switch(tag) {
+			case FDT_BEGIN_NODE:
+				if(level <= depth)
+					printf("%s%s {\n", &tabs[MAX_LEVEL - level], pathp);
+				level++;
+				offstack[level] = nodeoffset;
+				if (level >= MAX_LEVEL) {
+					printf("Aaaiii <splat> nested too deep.\n");
+					return 1;
+				}
+				break;
+			case FDT_END_NODE:
+				level--;
+				if(level <= depth)
+					printf("%s};\n", &tabs[MAX_LEVEL - level]);
+				if (level == 0) {
+					level = -1;		/* exit the loop */
+				}
+				break;
+			case FDT_PROP:
+				nodep = fdt_getprop (fdt, offstack[level], pathp, &len);
+				if (len < 0) {
+					printf ("libfdt %s\n", fdt_strerror(len));
+					return 1;
+				} else if (len == 0) {
+					/* the property has no value */
+					if(level <= depth)
+						printf("%s%s;\n", &tabs[MAX_LEVEL - level], pathp);
+				} else {
+					if(level <= depth) {
+						printf("%s%s=", &tabs[MAX_LEVEL - level], pathp);
+						print_data (nodep, len);
+						printf(";\n");
+					}
+				}
+				break;
+			case FDT_NOP:
+				break;
+			case FDT_END:
+				return 1;
+			default:
+				if(level <= depth)
+					printf("Unknown tag 0x%08X\n", tag);
+				return 1;
+			}
+			nodeoffset = nextoffset;
+		}
+
+	/********************************************************************
+	 * Remove a property/node
+	 ********************************************************************/
+	} else if (op == 'r') {
+		int  nodeoffset;	/* node offset from libfdt */
+		int  err;
+
+		/*
+		 * Get the path.  The root node is an oddball, the offset
+		 * is zero and has no name.
+		 */
+		if (strcmp(argv[2], "/") == 0) {
+			nodeoffset = 0;
+		} else {
+			nodeoffset = fdt_path_offset (fdt, argv[2]);
+			if (nodeoffset < 0) {
+				/*
+				 * Not found or something else bad happened.
+				 */
+				printf ("libfdt %s\n", fdt_strerror(nodeoffset));
+				return 1;
+			}
+		}
+		/*
+		 * Do the delete.  A fourth parameter means delete a property,
+		 * otherwise delete the node.
+		 */
+		if (argc > 3) {
+			err = fdt_delprop(fdt, nodeoffset, argv[3]);
+			if (err < 0) {
+				printf("fdt_delprop libfdt: %s\n", fdt_strerror(err));
+				return err;
+			}
+		} else {
+			err = fdt_del_node(fdt, nodeoffset);
+			if (err < 0) {
+				printf("fdt_del_node libfdt: %s\n", fdt_strerror(err));
+				return err;
+			}
+		}
+
+	/********************************************************************
+	 * Create a chosen node
+	 ********************************************************************/
+	} else if (op == 'c') {
+		fdt_chosen(fdt, 0, 0, 1);
+
+	/********************************************************************
+	 * Create a u-boot-env node
+	 ********************************************************************/
+	} else if (op == 'e') {
+		fdt_env(fdt);
+
+	/********************************************************************
+	 * Create a bd_t node
+	 ********************************************************************/
+	} else if (op == 'b') {
+		fdt_bd_t(fdt);
+
+	/********************************************************************
+	 * Unrecognized command
+	 ********************************************************************/
+	} else {
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	return 0;
+}
+
+/********************************************************************/
+
+static int fdt_valid(void)
+{
+	int  err;
+
+	if (fdt == NULL) {
+		printf ("The address of the fdt is invalid (NULL).\n");
+		return 0;
+	}
+
+	err = fdt_check_header(fdt);
+	if (err == 0)
+		return 1;	/* valid */
+
+	if (err < 0) {
+		printf("libfdt: %s", fdt_strerror(err));
+		/*
+		 * Be more informative on bad version.
+		 */
+		if (err == -FDT_ERR_BADVERSION) {
+			if (fdt_version(fdt) < FDT_FIRST_SUPPORTED_VERSION) {
+				printf (" - too old, fdt $d < %d",
+					fdt_version(fdt), FDT_FIRST_SUPPORTED_VERSION);
+				fdt = NULL;
+			}
+			if (fdt_last_comp_version(fdt) > FDT_LAST_SUPPORTED_VERSION) {
+				printf (" - too new, fdt $d > %d",
+					fdt_version(fdt), FDT_LAST_SUPPORTED_VERSION);
+				fdt = NULL;
+			}
+			return 0;
+		}
+		printf("\n");
+		return 0;
+	}
+	return 1;
+}
+
+/********************************************************************/
+
+/*
+ * OF flat tree handling
+ * Written by: Pantelis Antoniou <pantelis.antoniou@gmail.com>
+ * Updated by: Matthew McClintock <msm@freescale.com>
+ * Converted to libfdt by: Gerald Van Baren <vanbaren@cideas.com>
+ */
+
+static int is_printable_string(const void *data, int len)
+{
+	const char *s = data;
+
+	/* zero length is not */
+	if (len == 0)
+		return 0;
+
+	/* must terminate with zero */
+	if (s[len - 1] != '\0')
+		return 0;
+
+	/* printable or a null byte (concatenated strings) */
+	while (((*s == '\0') || isprint(*s)) && (len > 0)) {
+		/*
+		 * If we see a null, there are three possibilities:
+		 * 1) If len == 1, it is the end of the string, printable
+		 * 2) Next character also a null, not printable.
+		 * 3) Next character not a null, continue to check.
+		 */
+		if (s[0] == '\0') {
+			if (len == 1)
+				return 1;
+			if (s[1] == '\0')
+				return 0;
+		}
+		s++;
+		len--;
+	}
+
+	/* Not the null termination, or not done yet: not printable */
+	if (*s != '\0' || (len != 0))
+		return 0;
+
+	return 1;
+}
+
+static void print_data(const void *data, int len)
+{
+	int j;
+	const u8 *s;
+
+	/* no data, don't print */
+	if (len == 0)
+		return;
+
+	/*
+	 * It is a string, but it may have multiple strings (embedded '\0's).
+	 */
+	if (is_printable_string(data, len)) {
+		puts("\"");
+		j = 0;
+		while (j < len) {
+			if (j > 0)
+				puts("\", \"");
+			puts(data);
+			j    += strlen(data) + 1;
+			data += strlen(data) + 1;
+		}
+		puts("\"");
+		return;
+	}
+
+	switch (len) {
+	case 1:	 /* byte */
+		printf("<%02x>", (*(u8 *) data) & 0xff);
+		break;
+	case 2:	 /* half-word */
+		printf("<%04x>", be16_to_cpu(*(u16 *) data) & 0xffff);
+		break;
+	case 4:	 /* word */
+		printf("<%08x>", be32_to_cpu(*(u32 *) data) & 0xffffffffU);
+		break;
+	case 8:	 /* double-word */
+#if __WORDSIZE == 64
+		printf("<%016llx>", be64_to_cpu(*(uint64_t *) data));
+#else
+		printf("<%08x ", be32_to_cpu(*(u32 *) data) & 0xffffffffU);
+		data += 4;
+		printf("%08x>", be32_to_cpu(*(u32 *) data) & 0xffffffffU);
+#endif
+		break;
+	default:		/* anything else... hexdump */
+		printf("[");
+		for (j = 0, s = data; j < len; j++)
+			printf("%02x%s", s[j], j < len - 1 ? " " : "");
+		printf("]");
+
+		break;
+	}
+}
+
+/********************************************************************/
+
+U_BOOT_CMD(
+	fdt,	5,	0,	do_fdt,
+	"fdt     - flattened device tree utility commands\n",
+	    "addr   <addr> [<length>]        - Set the fdt location to <addr>\n"
+	"fdt move   <fdt> <newaddr> <length> - Copy the fdt to <addr>\n"
+	"fdt print  <path> [<prop>]          - Recursive print starting at <path>\n"
+	"fdt list   <path> [<prop>]          - Print one level starting at <path>\n"
+	"fdt set    <path> <prop> [<val>]    - Set <property> [to <val>]\n"
+	"fdt mknode <path> <node>            - Create a new node after <path>\n"
+	"fdt rm     <path> [<prop>]          - Delete the node or <property>\n"
+	"fdt chosen - Add/update the \"/chosen\" branch in the tree\n"
+#ifdef CONFIG_OF_HAS_UBOOT_ENV
+	"fdt env    - Add/replace the \"/u-boot-env\" branch in the tree\n"
+#endif
+#ifdef CONFIG_OF_HAS_BD_T
+	"fdt bd_t   - Add/replace the \"/bd_t\" branch in the tree\n"
+#endif
+	"Hints:\n"
+	" * Set a larger length with the fdt addr command to add to the blob.\n"
+	" * If the property you are setting/printing has a '#' character,\n"
+	"     you MUST escape it with a \\ character or quote it with \" or\n"
+	"     it will be ignored as a comment.\n"
+	" * If the value has spaces in it, you MUST escape the spaces with\n"
+	"     \\ characters or quote it with \"\"\n"
+	"Examples: fdt print /               # print the whole tree\n"
+	"          fdt print /cpus \"#address-cells\"\n"
+	"          fdt set   /cpus \"#address-cells\" \"[00 00 00 01]\"\n"
+);
+
+#endif /* CONFIG_OF_LIBFDT */

common/cmd_i2c.c

@@ -969,7 +969,7 @@ U_BOOT_CMD(
 	"i2c sdram chip - print SDRAM configuration information\n"
 #endif  /* CFG_CMD_SDRAM */
 );
-#else /* CONFIG_I2C_CMD_TREE */
+#endif /* CONFIG_I2C_CMD_TREE */
 U_BOOT_CMD(
 	imd,	4,	1,	do_i2c_md,		\
 	"imd     - i2c memory display\n",				\
@@ -1024,6 +1024,5 @@ U_BOOT_CMD(
 	"      (valid chip values 50..57)\n"
 );
 #endif
-#endif  /* CONFIG_I2C_CMD_TREE */
 
 #endif	/* CFG_CMD_I2C */

common/cmd_ide.c

@@ -423,7 +423,7 @@ int do_diskboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		}
 		part = simple_strtoul(++ep, NULL, 16);
 	}
-	if (get_partition_info (ide_dev_desc, part, &info)) {
+	if (get_partition_info (&ide_dev_desc[dev], part, &info)) {
 		SHOW_BOOT_PROGRESS (-1);
 		return 1;
 	}
@@ -513,9 +513,11 @@ void ide_init (void)
 #endif
 	unsigned char c;
 	int i, bus;
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+	unsigned int ata_reset_time;
+#endif
 #ifdef CONFIG_AMIGAONEG3SE
 	unsigned int max_bus_scan;
-	unsigned int ata_reset_time;
 	char *s;
 #endif
 #ifdef CONFIG_IDE_8xx_PCCARD
@@ -617,10 +619,9 @@ void ide_init (void)
 		udelay (100000);		/* 100 ms */
 		ide_outb (dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev));
 		udelay (100000);		/* 100 ms */
-#ifdef CONFIG_AMIGAONEG3SE
-		ata_reset_time = ATA_RESET_TIME;
-		s = getenv("ide_reset_timeout");
-		if (s) ata_reset_time = 2*simple_strtol(s, NULL, 10);
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
+		if ((s = getenv("ide_reset_timeout")) != NULL)
+			ata_reset_time = simple_strtol(s, NULL, 10);
 #endif
 		i = 0;
 		do {
@@ -628,7 +629,7 @@ void ide_init (void)
 
 			c = ide_inb (dev, ATA_STATUS);
 			i++;
-#ifdef CONFIG_AMIGAONEG3SE
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CONFIG_SC3)
 			if (i > (ata_reset_time * 100)) {
 #else
 			if (i > (ATA_RESET_TIME * 100)) {
@@ -1343,7 +1344,7 @@ ulong ide_read (int device, lbaint_t blknr, ulong blkcnt, void *buffer)
 
 		++n;
 		++blknr;
-		buffer += ATA_SECTORWORDS;
+		buffer += ATA_BLOCKSIZE;
 	}
 IDE_READ_E:
 	ide_led (DEVICE_LED(device), 0);	/* LED off	*/
@@ -1427,7 +1428,7 @@ ulong ide_write (int device, lbaint_t blknr, ulong blkcnt, void *buffer)
 		c = ide_inb (device, ATA_STATUS);	/* clear IRQ */
 		++n;
 		++blknr;
-		buffer += ATA_SECTORWORDS;
+		buffer += ATA_BLOCKSIZE;
 	}
 WR_OUT:
 	ide_led (DEVICE_LED(device), 0);	/* LED off	*/
@@ -2051,7 +2052,7 @@ ulong atapi_read (int device, lbaint_t blknr, ulong blkcnt, void *buffer)
 		n+=cnt;
 		blkcnt-=cnt;
 		blknr+=cnt;
-		buffer+=cnt*(ATAPI_READ_BLOCK_SIZE/4); /* ulong blocksize in ulong */
+		buffer+=(cnt*ATAPI_READ_BLOCK_SIZE);
 	} while (blkcnt > 0);
 	return (n);
 }

common/cmd_scsi.c

@@ -248,7 +248,7 @@ int do_scsiboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		}
 		part = simple_strtoul(++ep, NULL, 16);
 	}
-	if (get_partition_info (scsi_dev_desc, part, &info)) {
+	if (get_partition_info (&scsi_dev_desc[dev], part, &info)) {
 		printf("error reading partinfo\n");
 		return 1;
 	}

common/fdt_support.c

@@ -0,0 +1,347 @@
+/*
+ * (C) Copyright 2007
+ * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/ctype.h>
+#include <linux/types.h>
+
+#ifdef CONFIG_OF_LIBFDT
+
+#include <asm/global_data.h>
+#include <fdt.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+
+/*
+ * Global data (for the gd->bd)
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+
+/********************************************************************/
+
+int fdt_chosen(void *fdt, ulong initrd_start, ulong initrd_end, int force)
+{
+	bd_t *bd = gd->bd;
+	int   nodeoffset;
+	int   err;
+	u32   tmp;			/* used to set 32 bit integer properties */
+	char  *str;			/* used to set string properties */
+	ulong clock;
+
+	err = fdt_check_header(fdt);
+	if (err < 0) {
+		printf("libfdt: %s\n", fdt_strerror(err));
+		return err;
+	}
+
+	if (initrd_start && initrd_end) {
+		struct fdt_reserve_entry re;
+		int  used;
+		int  total;
+		int  j;
+
+		err = fdt_num_reservemap(fdt, &used, &total);
+		if (err < 0) {
+			printf("libfdt: %s\n", fdt_strerror(err));
+			return err;
+		}
+		if (used >= total) {
+			printf("fdt_chosen: no room in the reserved map (%d of %d)\n",
+				used, total);
+			return -1;
+		}
+		/*
+		 * Look for an existing entry and update it.  If we don't find
+		 * the entry, we will j be the next available slot.
+		 */
+		for (j = 0; j < used; j++) {
+			err = fdt_get_reservemap(fdt, j, &re);
+			if (re.address == initrd_start) {
+				break;
+			}
+		}
+		err = fdt_replace_reservemap_entry(fdt, j,
+			initrd_start, initrd_end - initrd_start + 1);
+		if (err < 0) {
+			printf("libfdt: %s\n", fdt_strerror(err));
+			return err;
+		}
+	}
+
+	/*
+	 * Find the "chosen" node.
+	 */
+	nodeoffset = fdt_path_offset (fdt, "/chosen");
+
+	/*
+	 * If we have a "chosen" node already the "force the writing"
+	 * is not set, our job is done.
+	 */
+	if ((nodeoffset >= 0) && !force)
+		return 0;
+
+	/*
+	 * No "chosen" node in the blob: create it.
+	 */
+	if (nodeoffset < 0) {
+		/*
+		 * Create a new node "/chosen" (offset 0 is root level)
+		 */
+		nodeoffset = fdt_add_subnode(fdt, 0, "chosen");
+		if (nodeoffset < 0) {
+			printf("libfdt: %s\n", fdt_strerror(nodeoffset));
+			return nodeoffset;
+		}
+	}
+
+	/*
+	 * Update pre-existing properties, create them if non-existant.
+	 */
+	str = getenv("bootargs");
+	if (str != NULL) {
+		err = fdt_setprop(fdt, nodeoffset, "bootargs", str, strlen(str)+1);
+		if (err < 0)
+			printf("libfdt: %s\n", fdt_strerror(err));
+	}
+	if (initrd_start && initrd_end) {
+		tmp = __cpu_to_be32(initrd_start);
+		err = fdt_setprop(fdt, nodeoffset, "linux,initrd-start", &tmp, sizeof(tmp));
+		if (err < 0)
+			printf("libfdt: %s\n", fdt_strerror(err));
+		tmp = __cpu_to_be32(initrd_end);
+		err = fdt_setprop(fdt, nodeoffset, "linux,initrd-end", &tmp, sizeof(tmp));
+		if (err < 0)
+			printf("libfdt: %s\n", fdt_strerror(err));
+	}
+#ifdef OF_STDOUT_PATH
+	err = fdt_setprop(fdt, nodeoffset, "linux,stdout-path", OF_STDOUT_PATH, strlen(OF_STDOUT_PATH)+1);
+	if (err < 0)
+		printf("libfdt: %s\n", fdt_strerror(err));
+#endif
+
+	nodeoffset = fdt_path_offset (fdt, "/cpus");
+	if (nodeoffset >= 0) {
+		clock = cpu_to_be32(bd->bi_intfreq);
+		err = fdt_setprop(fdt, nodeoffset, "clock-frequency", &clock, 4);
+		if (err < 0)
+			printf("libfdt: %s\n", fdt_strerror(err));
+	}
+#ifdef OF_TBCLK
+	nodeoffset = fdt_path_offset (fdt, "/cpus/" OF_CPU "/timebase-frequency");
+	if (nodeoffset >= 0) {
+		clock = cpu_to_be32(OF_TBCLK);
+		err = fdt_setprop(fdt, nodeoffset, "clock-frequency", &clock, 4);
+		if (err < 0)
+			printf("libfdt: %s\n", fdt_strerror(err));
+	}
+#endif
+	return err;
+}
+
+/********************************************************************/
+
+#ifdef CONFIG_OF_HAS_UBOOT_ENV
+
+/* Function that returns a character from the environment */
+extern uchar(*env_get_char) (int);
+
+
+int fdt_env(void *fdt)
+{
+	int   nodeoffset;
+	int   err;
+	int   k, nxt;
+	int i;
+	static char tmpenv[256];
+
+	err = fdt_check_header(fdt);
+	if (err < 0) {
+		printf("libfdt: %s\n", fdt_strerror(err));
+		return err;
+	}
+
+	/*
+	 * See if we already have a "u-boot-env" node, delete it if so.
+	 * Then create a new empty node.
+	 */
+	nodeoffset = fdt_path_offset (fdt, "/u-boot-env");
+	if (nodeoffset >= 0) {
+		err = fdt_del_node(fdt, nodeoffset);
+		if (err < 0) {
+			printf("libfdt: %s\n", fdt_strerror(err));
+			return err;
+		}
+	}
+	/*
+	 * Create a new node "/u-boot-env" (offset 0 is root level)
+	 */
+	nodeoffset = fdt_add_subnode(fdt, 0, "u-boot-env");
+	if (nodeoffset < 0) {
+		printf("libfdt: %s\n", fdt_strerror(nodeoffset));
+		return nodeoffset;
+	}
+
+	for (i = 0; env_get_char(i) != '\0'; i = nxt + 1) {
+		char *s, *lval, *rval;
+
+		/*
+		 * Find the end of the name=definition
+		 */
+		for (nxt = i; env_get_char(nxt) != '\0'; ++nxt)
+			;
+		s = tmpenv;
+		for (k = i; k < nxt && s < &tmpenv[sizeof(tmpenv) - 1]; ++k)
+			*s++ = env_get_char(k);
+		*s++ = '\0';
+		lval = tmpenv;
+		/*
+		 * Find the first '=': it separates the name from the value
+		 */
+		s = strchr(tmpenv, '=');
+		if (s != NULL) {
+			*s++ = '\0';
+			rval = s;
+		} else
+			continue;
+		err = fdt_setprop(fdt, nodeoffset, lval, rval, strlen(rval)+1);
+		if (err < 0) {
+			printf("libfdt: %s\n", fdt_strerror(err));
+			return err;
+		}
+	}
+	return 0;
+}
+#endif /* ifdef CONFIG_OF_HAS_UBOOT_ENV */
+
+/********************************************************************/
+
+#ifdef CONFIG_OF_HAS_BD_T
+
+#define BDM(x)	{	.name = #x, .offset = offsetof(bd_t, bi_ ##x ) }
+
+static const struct {
+	const char *name;
+	int offset;
+} bd_map[] = {
+	BDM(memstart),
+	BDM(memsize),
+	BDM(flashstart),
+	BDM(flashsize),
+	BDM(flashoffset),
+	BDM(sramstart),
+	BDM(sramsize),
+#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || defined(CONFIG_8260) \
+	|| defined(CONFIG_E500)
+	BDM(immr_base),
+#endif
+#if defined(CONFIG_MPC5xxx)
+	BDM(mbar_base),
+#endif
+#if defined(CONFIG_MPC83XX)
+	BDM(immrbar),
+#endif
+#if defined(CONFIG_MPC8220)
+	BDM(mbar_base),
+	BDM(inpfreq),
+	BDM(pcifreq),
+	BDM(pevfreq),
+	BDM(flbfreq),
+	BDM(vcofreq),
+#endif
+	BDM(bootflags),
+	BDM(ip_addr),
+	BDM(intfreq),
+	BDM(busfreq),
+#ifdef CONFIG_CPM2
+	BDM(cpmfreq),
+	BDM(brgfreq),
+	BDM(sccfreq),
+	BDM(vco),
+#endif
+#if defined(CONFIG_MPC5xxx)
+	BDM(ipbfreq),
+	BDM(pcifreq),
+#endif
+	BDM(baudrate),
+};
+
+
+int fdt_bd_t(void *fdt)
+{
+	bd_t *bd = gd->bd;
+	int   nodeoffset;
+	int   err;
+	u32   tmp;			/* used to set 32 bit integer properties */
+	int i;
+
+	err = fdt_check_header(fdt);
+	if (err < 0) {
+		printf("libfdt: %s\n", fdt_strerror(err));
+		return err;
+	}
+
+	/*
+	 * See if we already have a "bd_t" node, delete it if so.
+	 * Then create a new empty node.
+	 */
+	nodeoffset = fdt_path_offset (fdt, "/bd_t");
+	if (nodeoffset >= 0) {
+		err = fdt_del_node(fdt, nodeoffset);
+		if (err < 0) {
+			printf("libfdt: %s\n", fdt_strerror(err));
+			return err;
+		}
+	}
+	/*
+	 * Create a new node "/bd_t" (offset 0 is root level)
+	 */
+	nodeoffset = fdt_add_subnode(fdt, 0, "bd_t");
+	if (nodeoffset < 0) {
+		printf("libfdt: %s\n", fdt_strerror(nodeoffset));
+		return nodeoffset;
+	}
+	/*
+	 * Use the string/pointer structure to create the entries...
+	 */
+	for (i = 0; i < sizeof(bd_map)/sizeof(bd_map[0]); i++) {
+		tmp = cpu_to_be32(getenv("bootargs"));
+		err = fdt_setprop(fdt, nodeoffset, bd_map[i].name, &tmp, sizeof(tmp));
+		if (err < 0)
+			printf("libfdt: %s\n", fdt_strerror(err));
+	}
+	/*
+	 * Add a couple of oddball entries...
+	 */
+	err = fdt_setprop(fdt, nodeoffset, "enetaddr", &bd->bi_enetaddr, 6);
+	if (err < 0)
+		printf("libfdt: %s\n", fdt_strerror(err));
+	err = fdt_setprop(fdt, nodeoffset, "ethspeed", &bd->bi_ethspeed, 4);
+	if (err < 0)
+		printf("libfdt: %s\n", fdt_strerror(err));
+
+	return 0;
+}
+#endif /* ifdef CONFIG_OF_HAS_BD_T */
+
+#endif /* CONFIG_OF_LIBFDT */

common/serial.c

@@ -41,7 +41,7 @@ struct serial_device *default_serial_console (void)
    || defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4)
 	return &serial_scc_device;
 #elif defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
-   || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
+   || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx)
 #if defined(CONFIG_CONS_INDEX) && defined(CFG_NS16550_SERIAL)
 #if (CONFIG_CONS_INDEX==1)
 	return &eserial1_device;
@@ -91,7 +91,7 @@ void serial_initialize (void)
 #endif
 
 #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
- || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
+ || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx)
 	serial_register(&serial0_device);
 	serial_register(&serial1_device);
 #endif

cpu/74xx_7xx/cpu.c

@@ -44,6 +44,10 @@
 #include <74xx_7xx.h>
 #include <asm/cache.h>
 
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+#endif
+
 #ifdef CONFIG_AMIGAONEG3SE
 #include "../board/MAI/AmigaOneG3SE/via686.h"
 #include "../board/MAI/AmigaOneG3SE/memio.h"
@@ -101,6 +105,10 @@ get_cpu_type(void)
 		type = CPU_7457;
 		break;
 
+	case 0x8003:
+		type = CPU_7447A;
+		break;
+
 	case 0x8004:
 		type = CPU_7448;
 		break;
@@ -156,6 +164,10 @@ int checkcpu (void)
 		str = "MPC7410";
 		break;
 
+	case CPU_7447A:
+		str = "MPC7447A";
+		break;
+
 	case CPU_7448:
 		str = "MPC7448";
 		break;
@@ -264,20 +276,19 @@ do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 /*
  * For the 7400 the TB clock runs at 1/4 the cpu bus speed.
  */
-#ifdef CONFIG_AMIGAONEG3SE
+#if defined(CONFIG_AMIGAONEG3SE) || defined(CFG_CONFIG_BUS_CLK)
 unsigned long get_tbclk(void)
 {
 	return (gd->bus_clk / 4);
 }
-#else	/* ! CONFIG_AMIGAONEG3SE */
+#else	/* ! CONFIG_AMIGAONEG3SE and !CFG_CONFIG_BUS_CLK*/
 
 unsigned long get_tbclk (void)
 {
 	return CFG_BUS_HZ / 4;
 }
-#endif	/* CONFIG_AMIGAONEG3SE */
+#endif	/* CONFIG_AMIGAONEG3SE or CFG_CONFIG_BUS_CLK*/
 /* ------------------------------------------------------------------------- */
-
 #if defined(CONFIG_WATCHDOG)
 #if !defined(CONFIG_PCIPPC2) && !defined(CONFIG_BAB7xx)
 void
@@ -289,3 +300,30 @@ watchdog_reset(void)
 #endif	/* CONFIG_WATCHDOG */
 
 /* ------------------------------------------------------------------------- */
+
+#ifdef CONFIG_OF_FLAT_TREE
+void
+ft_cpu_setup (void *blob, bd_t *bd)
+{
+	u32 *p;
+	ulong clock;
+	int len;
+
+	clock = bd->bi_busfreq;
+
+	p = ft_get_prop (blob, "/cpus/" OF_CPU "/bus-frequency", &len);
+	if (p != NULL)
+		*p = cpu_to_be32 (clock);
+
+#if defined(CONFIG_TSI108_ETH)
+	p = ft_get_prop (blob, "/" OF_TSI "/ethernet@6200/address", &len);
+		memcpy (p, bd->bi_enetaddr, 6);
+#endif
+
+#if defined(CONFIG_HAS_ETH1)
+	p = ft_get_prop (blob, "/" OF_TSI "/ethernet@6600/address", &len);
+		memcpy (p, bd->bi_enet1addr, 6);
+#endif
+}
+#endif
+/* ------------------------------------------------------------------------- */

cpu/74xx_7xx/cpu_init.c

@@ -43,6 +43,7 @@ cpu_init_f (void)
 	case CPU_7450:
 	case CPU_7455:
 	case CPU_7457:
+	case CPU_7447A:
 	case CPU_7448:
 		/* enable the timebase bit in HID0 */
 		set_hid0(get_hid0() | 0x4000000);

cpu/74xx_7xx/speed.c

@@ -31,6 +31,8 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+extern unsigned long get_board_bus_clk (void);
+
 static const int hid1_multipliers_x_10[] = {
 	25,	/* 0000 - 2.5x */
 	75,	/* 0001 - 7.5x */
@@ -50,6 +52,42 @@ static const int hid1_multipliers_x_10[] = {
 	0	/* 1111 - off */
 };
 
+/* PLL_CFG[0:4] table for cpu 7448/7447A/7455/7457 */
+static const int hid1_74xx_multipliers_x_10[] = {
+	115,	/* 00000 - 11.5x  */
+	170,	/* 00001 - 17x    */
+	75,	/* 00010 -  7.5x  */
+	150,	/* 00011 - 15x    */
+	70,	/* 00100 -  7x    */
+	180,	/* 00101 - 18x    */
+	10,	/* 00110 - bypass */
+	200,	/* 00111 - 20x    */
+	20,	/* 01000 -  2x    */
+	210,	/* 01001 - 21x    */
+	65,	/* 01010 -  6.5x  */
+	130,	/* 01011 - 13x    */
+	85,	/* 01100 -  8.5x  */
+	240,	/* 01101 - 24x    */
+	95,	/* 01110 -  9.5x  */
+	90,	/* 01111 -  9x    */
+	30,	/* 10000 -  3x    */
+	105,	/* 10001 - 10.5x  */
+	55,	/* 10010 -  5.5x  */
+	110,	/* 10011 - 11x    */
+	40,	/* 10100 -  4x    */
+	100,	/* 10101 - 10x    */
+	50,	/* 10110 -  5x    */
+	120,	/* 10111 - 12x    */
+	80,	/* 11000 -  8x    */
+	140,	/* 11001 - 14x    */
+	60,	/* 11010 -  6x    */
+	160,	/* 11011 - 16x    */
+	135,	/* 11100 - 13.5x  */
+	280,	/* 11101 - 28x    */
+	0,	/* 11110 - off    */
+	125	/* 11111 - 12.5x  */
+};
+
 static const int hid1_fx_multipliers_x_10[] = {
 	00,	/* 0000 - off */
 	00,	/* 0001 - off */
@@ -89,22 +127,30 @@ int get_clocks (void)
 {
 	ulong clock = 0;
 
+#ifdef CFG_BUS_CLK
+	gd->bus_clk = CFG_BUS_CLK;	/* bus clock is a fixed frequency */
+#else
+	gd->bus_clk = get_board_bus_clk ();	/* bus clock is configurable */
+#endif
+
 	/* calculate the clock frequency based upon the CPU type */
 	switch (get_cpu_type()) {
+	case CPU_7447A:
 	case CPU_7448:
 	case CPU_7455:
 	case CPU_7457:
 		/*
-		 * It is assumed that the PLL_EXT line is zero.
 		 * Make sure division is done before multiplication to prevent 32-bit
 		 * arithmetic overflows which will cause a negative number
 		 */
-		clock = (CFG_BUS_CLK / 10) * hid1_multipliers_x_10[(get_hid1 () >> 13) & 0xF];
+		clock = (gd->bus_clk / 10) *
+			hid1_74xx_multipliers_x_10[(get_hid1 () >> 12) & 0x1F];
 		break;
 
 	case CPU_750GX:
 	case CPU_750FX:
-		clock = CFG_BUS_CLK * hid1_fx_multipliers_x_10[get_hid1 () >> 27] / 10;
+		clock = gd->bus_clk *
+			hid1_fx_multipliers_x_10[get_hid1 () >> 27] / 10;
 		break;
 
 	case CPU_7450:
@@ -121,7 +167,8 @@ int get_clocks (void)
 		 * Make sure division is done before multiplication to prevent 32-bit
 		 * arithmetic overflows which will cause a negative number
 		 */
-		clock = (CFG_BUS_CLK / 10) * hid1_multipliers_x_10[get_hid1 () >> 28];
+		clock = (gd->bus_clk / 10) *
+			hid1_multipliers_x_10[get_hid1 () >> 28];
 		break;
 
 	case CPU_UNKNOWN:
@@ -131,7 +178,6 @@ int get_clocks (void)
 	}
 
 	gd->cpu_clk = clock;
-	gd->bus_clk = CFG_BUS_CLK;
 
 	return (0);
 }

cpu/at32ap/Makefile

@@ -30,7 +30,7 @@ LIB	:= $(obj)lib$(CPU).a
 START	:= start.o
 SOBJS	:= entry.o
 COBJS	:= cpu.o hsdramc.o exception.o cache.o
-COBJS	+= interrupts.o device.o pm.o pio.o
+COBJS	+= interrupts.o pio.o atmel_mci.o
 SRCS	:= $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
 START	:= $(addprefix $(obj),$(START))

cpu/at32ap/at32ap7000/Makefile

@@ -24,7 +24,7 @@ include $(TOPDIR)/config.mk
 
 LIB	:= $(obj)lib$(SOC).a
 
-COBJS	:= hebi.o devices.o
+COBJS	:= gpio.o
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
 

cpu/at32ap/at32ap7000/devices.c

@@ -1,448 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-
-#include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
-
-#include "../sm.h"
-
-#define ARRAY_SIZE(x)	(sizeof(x) / sizeof((x)[0]))
-
-const struct clock_domain chip_clock[] = {
-	[CLOCK_CPU] = {
-		.reg	= SM_PM_CPU_MASK,
-		.id	= CLOCK_CPU,
-		.bridge	= NO_DEVICE,
-	},
-	[CLOCK_HSB] = {
-		.reg	= SM_PM_HSB_MASK,
-		.id	= CLOCK_HSB,
-		.bridge	= NO_DEVICE,
-	},
-	[CLOCK_PBA] = {
-		.reg	= SM_PM_PBA_MASK,
-		.id	= CLOCK_PBA,
-		.bridge	= DEVICE_PBA_BRIDGE,
-	},
-	[CLOCK_PBB] = {
-		.reg	= SM_PM_PBB_MASK,
-		.id	= CLOCK_PBB,
-		.bridge	= DEVICE_PBB_BRIDGE,
-	},
-};
-
-static const struct resource hebi_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 0 },
-		},
-	}, {
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBB, 13 },
-		},
-	}, {
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBB, 14 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio	= { 27, DEVICE_PIOE, GPIO_FUNC_A, 0 },
-		},
-	},
-};
-static const struct resource pba_bridge_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 1 },
-		}
-	}, {
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			/* HSB-HSB Bridge */
-			.clock	= { CLOCK_HSB, 4 },
-		},
-	},
-};
-static const struct resource pbb_bridge_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 2 },
-		},
-	},
-};
-static const struct resource hramc_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 3 },
-		},
-	},
-};
-static const struct resource pioa_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 10 },
-		},
-	},
-};
-static const struct resource piob_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 11 },
-		},
-	},
-};
-static const struct resource pioc_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 12 },
-		},
-	},
-};
-static const struct resource piod_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 13 },
-		},
-	},
-};
-static const struct resource pioe_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 14 },
-		},
-	},
-};
-static const struct resource sm_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBB, 0 },
-		},
-	},
-};
-static const struct resource intc_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock = { CLOCK_PBB, 1 },
-		},
-	},
-};
-static const struct resource hmatrix_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock = { CLOCK_PBB, 2 },
-		},
-	},
-};
-#if defined(CFG_HPDC)
-static const struct resource hpdc_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 16 },
-		},
-	},
-};
-#endif
-#if defined(CFG_MACB0)
-static const struct resource macb0_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 8 },
-		},
-	}, {
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBB, 6 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio	= { 19, DEVICE_PIOC, GPIO_FUNC_A, 0 },
-		},
-	},
-};
-#endif
-#if defined(CFG_MACB1)
-static const struct resource macb1_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 9 },
-		},
-	}, {
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBB, 7 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio	= { 12, DEVICE_PIOC, GPIO_FUNC_B, 19 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio	= { 14, DEVICE_PIOD, GPIO_FUNC_B, 2 },
-		},
-	},
-};
-#endif
-#if defined(CFG_LCDC)
-static const struct resource lcdc_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 7 },
-		},
-	},
-};
-#endif
-#if defined(CFG_USART0)
-static const struct resource usart0_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 3 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio = { 2, DEVICE_PIOA, GPIO_FUNC_B, 8 },
-		},
-	},
-};
-#endif
-#if defined(CFG_USART1)
-static const struct resource usart1_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 4 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio = { 2, DEVICE_PIOA, GPIO_FUNC_A, 17 },
-		},
-	},
-};
-#endif
-#if defined(CFG_USART2)
-static const struct resource usart2_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 5 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio = { 2, DEVICE_PIOB, GPIO_FUNC_B, 26 },
-		},
-	},
-};
-#endif
-#if defined(CFG_USART3)
-static const struct resource usart3_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBA, 6 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio = { 2, DEVICE_PIOB, GPIO_FUNC_B, 17 },
-		},
-	},
-};
-#endif
-#if defined(CFG_MMCI)
-static const struct resource mmci_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_PBB, 9 },
-		},
-	}, {
-		.type	= RESOURCE_GPIO,
-		.u	= {
-			.gpio = { 6, DEVICE_PIOA, GPIO_FUNC_A, 10 },
-		},
-	},
-};
-#endif
-#if defined(CFG_DMAC)
-static const struct resource dmac_resource[] = {
-	{
-		.type	= RESOURCE_CLOCK,
-		.u	= {
-			.clock	= { CLOCK_HSB, 10 },
-		},
-	},
-};
-#endif
-
-const struct device chip_device[] = {
-	[DEVICE_HEBI] = {
-		.regs		= (void *)HSMC_BASE,
-		.nr_resources	= ARRAY_SIZE(hebi_resource),
-		.resource	= hebi_resource,
-	},
-	[DEVICE_PBA_BRIDGE] = {
-		.nr_resources	= ARRAY_SIZE(pba_bridge_resource),
-		.resource	= pba_bridge_resource,
-	},
-	[DEVICE_PBB_BRIDGE] = {
-		.nr_resources	= ARRAY_SIZE(pbb_bridge_resource),
-		.resource	= pbb_bridge_resource,
-	},
-	[DEVICE_HRAMC] = {
-		.nr_resources	= ARRAY_SIZE(hramc_resource),
-		.resource	= hramc_resource,
-	},
-	[DEVICE_PIOA] = {
-		.regs		= (void *)PIOA_BASE,
-		.nr_resources	= ARRAY_SIZE(pioa_resource),
-		.resource	= pioa_resource,
-	},
-	[DEVICE_PIOB] = {
-		.regs		= (void *)PIOB_BASE,
-		.nr_resources	= ARRAY_SIZE(piob_resource),
-		.resource	= piob_resource,
-	},
-	[DEVICE_PIOC] = {
-		.regs		= (void *)PIOC_BASE,
-		.nr_resources	= ARRAY_SIZE(pioc_resource),
-		.resource	= pioc_resource,
-	},
-	[DEVICE_PIOD] = {
-		.regs		= (void *)PIOD_BASE,
-		.nr_resources	= ARRAY_SIZE(piod_resource),
-		.resource	= piod_resource,
-	},
-	[DEVICE_PIOE] = {
-		.regs		= (void *)PIOE_BASE,
-		.nr_resources	= ARRAY_SIZE(pioe_resource),
-		.resource	= pioe_resource,
-	},
-	[DEVICE_SM] = {
-		.regs		= (void *)SM_BASE,
-		.nr_resources	= ARRAY_SIZE(sm_resource),
-		.resource	= sm_resource,
-	},
-	[DEVICE_INTC] = {
-		.regs		= (void *)INTC_BASE,
-		.nr_resources	= ARRAY_SIZE(intc_resource),
-		.resource	= intc_resource,
-	},
-	[DEVICE_HMATRIX] = {
-		.regs		= (void *)HMATRIX_BASE,
-		.nr_resources	= ARRAY_SIZE(hmatrix_resource),
-		.resource	= hmatrix_resource,
-	},
-#if defined(CFG_HPDC)
-	[DEVICE_HPDC] = {
-		.nr_resources	= ARRAY_SIZE(hpdc_resource),
-		.resource	= hpdc_resource,
-	},
-#endif
-#if defined(CFG_MACB0)
-	[DEVICE_MACB0] = {
-		.regs		= (void *)MACB0_BASE,
-		.nr_resources	= ARRAY_SIZE(macb0_resource),
-		.resource	= macb0_resource,
-	},
-#endif
-#if defined(CFG_MACB1)
-	[DEVICE_MACB1] = {
-		.regs		= (void *)MACB1_BASE,
-		.nr_resources	= ARRAY_SIZE(macb1_resource),
-		.resource	= macb1_resource,
-	},
-#endif
-#if defined(CFG_LCDC)
-	[DEVICE_LCDC] = {
-		.nr_resources	= ARRAY_SIZE(lcdc_resource),
-		.resource	= lcdc_resource,
-	},
-#endif
-#if defined(CFG_USART0)
-	[DEVICE_USART0] = {
-		.regs		= (void *)USART0_BASE,
-		.nr_resources	= ARRAY_SIZE(usart0_resource),
-		.resource	= usart0_resource,
-	},
-#endif
-#if defined(CFG_USART1)
-	[DEVICE_USART1] = {
-		.regs		= (void *)USART1_BASE,
-		.nr_resources	= ARRAY_SIZE(usart1_resource),
-		.resource	= usart1_resource,
-	},
-#endif
-#if defined(CFG_USART2)
-	[DEVICE_USART2] = {
-		.regs		= (void *)USART2_BASE,
-		.nr_resources	= ARRAY_SIZE(usart2_resource),
-		.resource	= usart2_resource,
-	},
-#endif
-#if defined(CFG_USART3)
-	[DEVICE_USART3] = {
-		.regs		= (void *)USART3_BASE,
-		.nr_resources	= ARRAY_SIZE(usart3_resource),
-		.resource	= usart3_resource,
-	},
-#endif
-#if defined(CFG_MMCI)
-	[DEVICE_MMCI] = {
-		.regs		= (void *)MMCI_BASE,
-		.nr_resources	= ARRAY_SIZE(mmci_resource),
-		.resource	= mmci_resource,
-	},
-#endif
-#if defined(CFG_DMAC)
-	[DEVICE_DMAC] = {
-		.regs		= (void *)DMAC_BASE,
-		.nr_resources	= ARRAY_SIZE(dmac_resource),
-		.resource	= dmac_resource,
-	},
-#endif
-};

cpu/at32ap/at32ap7000/gpio.c

@@ -0,0 +1,137 @@
+/*
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+
+#include <asm/arch/gpio.h>
+
+/*
+ * Lots of small functions here. We depend on --gc-sections getting
+ * rid of the ones we don't need.
+ */
+void gpio_enable_ebi(void)
+{
+#ifdef CFG_HSDRAMC
+#ifndef CFG_SDRAM_16BIT
+	gpio_select_periph_A(GPIO_PIN_PE0, 0);
+	gpio_select_periph_A(GPIO_PIN_PE1, 0);
+	gpio_select_periph_A(GPIO_PIN_PE2, 0);
+	gpio_select_periph_A(GPIO_PIN_PE3, 0);
+	gpio_select_periph_A(GPIO_PIN_PE4, 0);
+	gpio_select_periph_A(GPIO_PIN_PE5, 0);
+	gpio_select_periph_A(GPIO_PIN_PE6, 0);
+	gpio_select_periph_A(GPIO_PIN_PE7, 0);
+	gpio_select_periph_A(GPIO_PIN_PE8, 0);
+	gpio_select_periph_A(GPIO_PIN_PE9, 0);
+	gpio_select_periph_A(GPIO_PIN_PE10, 0);
+	gpio_select_periph_A(GPIO_PIN_PE11, 0);
+	gpio_select_periph_A(GPIO_PIN_PE12, 0);
+	gpio_select_periph_A(GPIO_PIN_PE13, 0);
+	gpio_select_periph_A(GPIO_PIN_PE14, 0);
+	gpio_select_periph_A(GPIO_PIN_PE15, 0);
+#endif
+	gpio_select_periph_A(GPIO_PIN_PE26, 0);
+#endif
+}
+
+void gpio_enable_usart0(void)
+{
+	gpio_select_periph_B(GPIO_PIN_PA8, 0);
+	gpio_select_periph_B(GPIO_PIN_PA9, 0);
+}
+
+void gpio_enable_usart1(void)
+{
+	gpio_select_periph_A(GPIO_PIN_PA17, 0);
+	gpio_select_periph_A(GPIO_PIN_PA18, 0);
+}
+
+void gpio_enable_usart2(void)
+{
+	gpio_select_periph_B(GPIO_PIN_PB26, 0);
+	gpio_select_periph_B(GPIO_PIN_PB27, 0);
+}
+
+void gpio_enable_usart3(void)
+{
+	gpio_select_periph_B(GPIO_PIN_PB18, 0);
+	gpio_select_periph_B(GPIO_PIN_PB19, 0);
+}
+
+void gpio_enable_macb0(void)
+{
+	gpio_select_periph_A(GPIO_PIN_PC3,  0);	/* TXD0	*/
+	gpio_select_periph_A(GPIO_PIN_PC4,  0);	/* TXD1	*/
+	gpio_select_periph_A(GPIO_PIN_PC7,  0);	/* TXEN	*/
+	gpio_select_periph_A(GPIO_PIN_PC8,  0);	/* TXCK */
+	gpio_select_periph_A(GPIO_PIN_PC9,  0);	/* RXD0	*/
+	gpio_select_periph_A(GPIO_PIN_PC10, 0);	/* RXD1	*/
+	gpio_select_periph_A(GPIO_PIN_PC13, 0);	/* RXER	*/
+	gpio_select_periph_A(GPIO_PIN_PC15, 0);	/* RXDV	*/
+	gpio_select_periph_A(GPIO_PIN_PC16, 0);	/* MDC	*/
+	gpio_select_periph_A(GPIO_PIN_PC17, 0);	/* MDIO	*/
+#if !defined(CONFIG_RMII)
+	gpio_select_periph_A(GPIO_PIN_PC0,  0);	/* COL	*/
+	gpio_select_periph_A(GPIO_PIN_PC1,  0);	/* CRS	*/
+	gpio_select_periph_A(GPIO_PIN_PC2,  0);	/* TXER	*/
+	gpio_select_periph_A(GPIO_PIN_PC5,  0);	/* TXD2	*/
+	gpio_select_periph_A(GPIO_PIN_PC6,  0);	/* TXD3 */
+	gpio_select_periph_A(GPIO_PIN_PC11, 0);	/* RXD2	*/
+	gpio_select_periph_A(GPIO_PIN_PC12, 0);	/* RXD3	*/
+	gpio_select_periph_A(GPIO_PIN_PC14, 0);	/* RXCK	*/
+	gpio_select_periph_A(GPIO_PIN_PC18, 0);	/* SPD	*/
+#endif
+}
+
+void gpio_enable_macb1(void)
+{
+	gpio_select_periph_B(GPIO_PIN_PD13, 0);	/* TXD0	*/
+	gpio_select_periph_B(GPIO_PIN_PD14, 0);	/* TXD1	*/
+	gpio_select_periph_B(GPIO_PIN_PD11, 0);	/* TXEN	*/
+	gpio_select_periph_B(GPIO_PIN_PD12, 0);	/* TXCK */
+	gpio_select_periph_B(GPIO_PIN_PD10, 0);	/* RXD0	*/
+	gpio_select_periph_B(GPIO_PIN_PD6,  0);	/* RXD1	*/
+	gpio_select_periph_B(GPIO_PIN_PD5,  0);	/* RXER	*/
+	gpio_select_periph_B(GPIO_PIN_PD4,  0);	/* RXDV	*/
+	gpio_select_periph_B(GPIO_PIN_PD3,  0);	/* MDC	*/
+	gpio_select_periph_B(GPIO_PIN_PD2,  0);	/* MDIO	*/
+#if !defined(CONFIG_RMII)
+	gpio_select_periph_B(GPIO_PIN_PC19, 0);	/* COL	*/
+	gpio_select_periph_B(GPIO_PIN_PC23, 0);	/* CRS	*/
+	gpio_select_periph_B(GPIO_PIN_PC26, 0);	/* TXER	*/
+	gpio_select_periph_B(GPIO_PIN_PC27, 0);	/* TXD2	*/
+	gpio_select_periph_B(GPIO_PIN_PC28, 0);	/* TXD3 */
+	gpio_select_periph_B(GPIO_PIN_PC29, 0);	/* RXD2	*/
+	gpio_select_periph_B(GPIO_PIN_PC30, 0);	/* RXD3	*/
+	gpio_select_periph_B(GPIO_PIN_PC24, 0);	/* RXCK	*/
+	gpio_select_periph_B(GPIO_PIN_PD15, 0);	/* SPD	*/
+#endif
+}
+
+void gpio_enable_mmci(void)
+{
+	gpio_select_periph_A(GPIO_PIN_PA10, 0);	/* CLK	 */
+	gpio_select_periph_A(GPIO_PIN_PA11, 0);	/* CMD	 */
+	gpio_select_periph_A(GPIO_PIN_PA12, 0);	/* DATA0 */
+	gpio_select_periph_A(GPIO_PIN_PA13, 0);	/* DATA1 */
+	gpio_select_periph_A(GPIO_PIN_PA14, 0);	/* DATA2 */
+	gpio_select_periph_A(GPIO_PIN_PA15, 0);	/* DATA3 */
+}

cpu/at32ap/atmel_mci.c

@@ -0,0 +1,477 @@
+/*
+ * Copyright (C) 2004-2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+
+#ifdef CONFIG_MMC
+
+#include <part.h>
+#include <mmc.h>
+
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/byteorder.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/memory-map.h>
+
+#include "atmel_mci.h"
+
+#ifdef DEBUG
+#define pr_debug(fmt, args...) printf(fmt, ##args)
+#else
+#define pr_debug(...) do { } while(0)
+#endif
+
+#ifndef CFG_MMC_CLK_OD
+#define CFG_MMC_CLK_OD		150000
+#endif
+
+#ifndef CFG_MMC_CLK_PP
+#define CFG_MMC_CLK_PP		5000000
+#endif
+
+#ifndef CFG_MMC_OP_COND
+#define CFG_MMC_OP_COND		0x00100000
+#endif
+
+#define MMC_DEFAULT_BLKLEN	512
+#define MMC_DEFAULT_RCA		1
+
+static unsigned int mmc_rca;
+static block_dev_desc_t mmc_blkdev;
+
+block_dev_desc_t *mmc_get_dev(int dev)
+{
+	return &mmc_blkdev;
+}
+
+static void mci_set_mode(unsigned long hz, unsigned long blklen)
+{
+	unsigned long bus_hz;
+	unsigned long clkdiv;
+
+	bus_hz = get_mci_clk_rate();
+	clkdiv = (bus_hz / hz) / 2 - 1;
+
+	pr_debug("mmc: setting clock %lu Hz, block size %lu\n",
+		 hz, blklen);
+
+	if (clkdiv & ~255UL) {
+		clkdiv = 255;
+		printf("mmc: clock %lu too low; setting CLKDIV to 255\n",
+			hz);
+	}
+
+	blklen &= 0xfffc;
+	mmci_writel(MR, (MMCI_BF(CLKDIV, clkdiv)
+			 | MMCI_BF(BLKLEN, blklen)));
+}
+
+#define RESP_NO_CRC	1
+#define R1		MMCI_BF(RSPTYP, 1)
+#define R2		MMCI_BF(RSPTYP, 2)
+#define R3		(R1 | RESP_NO_CRC)
+#define R6		R1
+#define NID		MMCI_BF(MAXLAT, 0)
+#define NCR		MMCI_BF(MAXLAT, 1)
+#define TRCMD_START	MMCI_BF(TRCMD, 1)
+#define TRDIR_READ	MMCI_BF(TRDIR, 1)
+#define TRTYP_BLOCK	MMCI_BF(TRTYP, 0)
+#define INIT_CMD	MMCI_BF(SPCMD, 1)
+#define OPEN_DRAIN	MMCI_BF(OPDCMD, 1)
+
+#define ERROR_FLAGS	(MMCI_BIT(DTOE)			\
+			 | MMCI_BIT(RDIRE)		\
+			 | MMCI_BIT(RENDE)		\
+			 | MMCI_BIT(RINDE)		\
+			 | MMCI_BIT(RTOE))
+
+static int
+mmc_cmd(unsigned long cmd, unsigned long arg,
+	void *resp, unsigned long flags)
+{
+	unsigned long *response = resp;
+	int i, response_words = 0;
+	unsigned long error_flags;
+	u32 status;
+
+	pr_debug("mmc: CMD%lu 0x%lx (flags 0x%lx)\n",
+		 cmd, arg, flags);
+
+	error_flags = ERROR_FLAGS;
+	if (!(flags & RESP_NO_CRC))
+		error_flags |= MMCI_BIT(RCRCE);
+
+	flags &= ~MMCI_BF(CMDNB, ~0UL);
+
+	if (MMCI_BFEXT(RSPTYP, flags) == MMCI_RSPTYP_48_BIT_RESP)
+		response_words = 1;
+	else if (MMCI_BFEXT(RSPTYP, flags) == MMCI_RSPTYP_136_BIT_RESP)
+		response_words = 4;
+
+	mmci_writel(ARGR, arg);
+	mmci_writel(CMDR, cmd | flags);
+	do {
+		udelay(40);
+		status = mmci_readl(SR);
+	} while (!(status & MMCI_BIT(CMDRDY)));
+
+	pr_debug("mmc: status 0x%08lx\n", status);
+
+	if (status & ERROR_FLAGS) {
+		printf("mmc: command %lu failed (status: 0x%08lx)\n",
+		       cmd, status);
+		return -EIO;
+	}
+
+	if (response_words)
+		pr_debug("mmc: response:");
+
+	for (i = 0; i < response_words; i++) {
+		response[i] = mmci_readl(RSPR);
+		pr_debug(" %08lx", response[i]);
+	}
+	pr_debug("\n");
+
+	return 0;
+}
+
+static int mmc_acmd(unsigned long cmd, unsigned long arg,
+		    void *resp, unsigned long flags)
+{
+	unsigned long aresp[4];
+	int ret;
+
+	/*
+	 * Seems like the APP_CMD part of an ACMD has 64 cycles max
+	 * latency even though the ACMD part doesn't. This isn't
+	 * entirely clear in the SD Card spec, but some cards refuse
+	 * to work if we attempt to use 5 cycles max latency here...
+	 */
+	ret = mmc_cmd(MMC_CMD_APP_CMD, 0, aresp,
+		      R1 | NCR | (flags & OPEN_DRAIN));
+	if (ret)
+		return ret;
+	if ((aresp[0] & (R1_ILLEGAL_COMMAND | R1_APP_CMD)) != R1_APP_CMD)
+		return -ENODEV;
+
+	ret = mmc_cmd(cmd, arg, resp, flags);
+	return ret;
+}
+
+static unsigned long
+mmc_bread(int dev, unsigned long start, lbaint_t blkcnt,
+	  unsigned long *buffer)
+{
+	int ret, i = 0;
+	unsigned long resp[4];
+	unsigned long card_status, data;
+	unsigned long wordcount;
+	u32 status;
+
+	if (blkcnt == 0)
+		return 0;
+
+	pr_debug("mmc_bread: dev %d, start %lx, blkcnt %lx\n",
+		 dev, start, blkcnt);
+
+	/* Put the device into Transfer state */
+	ret = mmc_cmd(MMC_CMD_SELECT_CARD, mmc_rca << 16, resp, R1 | NCR);
+	if (ret) goto fail;
+
+	/* Set block length */
+	ret = mmc_cmd(MMC_CMD_SET_BLOCKLEN, mmc_blkdev.blksz, resp, R1 | NCR);
+	if (ret) goto fail;
+
+	pr_debug("MCI_DTOR = %08lx\n", mmci_readl(DTOR));
+
+	for (i = 0; i < blkcnt; i++, start++) {
+		ret = mmc_cmd(MMC_CMD_READ_SINGLE_BLOCK,
+			      start * mmc_blkdev.blksz, resp,
+			      (R1 | NCR | TRCMD_START | TRDIR_READ
+			       | TRTYP_BLOCK));
+		if (ret) goto fail;
+
+		ret = -EIO;
+		wordcount = 0;
+		do {
+			do {
+				status = mmci_readl(SR);
+				if (status & (ERROR_FLAGS | MMCI_BIT(OVRE)))
+					goto fail;
+			} while (!(status & MMCI_BIT(RXRDY)));
+
+			if (status & MMCI_BIT(RXRDY)) {
+				data = mmci_readl(RDR);
+				/* pr_debug("%x\n", data); */
+				*buffer++ = data;
+				wordcount++;
+			}
+		} while(wordcount < (512 / 4));
+
+		pr_debug("mmc: read %u words, waiting for BLKE\n", wordcount);
+
+		do {
+			status = mmci_readl(SR);
+		} while (!(status & MMCI_BIT(BLKE)));
+
+		putc('.');
+	}
+
+out:
+	/* Put the device back into Standby state */
+	mmc_cmd(MMC_CMD_SELECT_CARD, 0, resp, NCR);
+	return i;
+
+fail:
+	mmc_cmd(MMC_CMD_SEND_STATUS, mmc_rca << 16, &card_status, R1 | NCR);
+	printf("mmc: bread failed, card status = ", card_status);
+	goto out;
+}
+
+static void mmc_parse_cid(struct mmc_cid *cid, unsigned long *resp)
+{
+	cid->mid = resp[0] >> 24;
+	cid->oid = (resp[0] >> 8) & 0xffff;
+	cid->pnm[0] = resp[0];
+	cid->pnm[1] = resp[1] >> 24;
+	cid->pnm[2] = resp[1] >> 16;
+	cid->pnm[3] = resp[1] >> 8;
+	cid->pnm[4] = resp[1];
+	cid->pnm[5] = resp[2] >> 24;
+	cid->pnm[6] = 0;
+	cid->prv = resp[2] >> 16;
+	cid->psn = (resp[2] << 16) | (resp[3] >> 16);
+	cid->mdt = resp[3] >> 8;
+}
+
+static void sd_parse_cid(struct mmc_cid *cid, unsigned long *resp)
+{
+	cid->mid = resp[0] >> 24;
+	cid->oid = (resp[0] >> 8) & 0xffff;
+	cid->pnm[0] = resp[0];
+	cid->pnm[1] = resp[1] >> 24;
+	cid->pnm[2] = resp[1] >> 16;
+	cid->pnm[3] = resp[1] >> 8;
+	cid->pnm[4] = resp[1];
+	cid->pnm[5] = 0;
+	cid->pnm[6] = 0;
+	cid->prv = resp[2] >> 24;
+	cid->psn = (resp[2] << 8) | (resp[3] >> 24);
+	cid->mdt = (resp[3] >> 8) & 0x0fff;
+}
+
+static void mmc_dump_cid(const struct mmc_cid *cid)
+{
+	printf("Manufacturer ID:       %02lX\n", cid->mid);
+	printf("OEM/Application ID:    %04lX\n", cid->oid);
+	printf("Product name:          %s\n", cid->pnm);
+	printf("Product Revision:      %lu.%lu\n",
+	       cid->prv >> 4, cid->prv & 0x0f);
+	printf("Product Serial Number: %lu\n", cid->psn);
+	printf("Manufacturing Date:    %02lu/%02lu\n",
+	       cid->mdt >> 4, cid->mdt & 0x0f);
+}
+
+static void mmc_dump_csd(const struct mmc_csd *csd)
+{
+	unsigned long *csd_raw = (unsigned long *)csd;
+	printf("CSD data: %08lx %08lx %08lx %08lx\n",
+	       csd_raw[0], csd_raw[1], csd_raw[2], csd_raw[3]);
+	printf("CSD structure version:   1.%u\n", csd->csd_structure);
+	printf("MMC System Spec version: %u\n", csd->spec_vers);
+	printf("Card command classes:    %03x\n", csd->ccc);
+	printf("Read block length:       %u\n", 1 << csd->read_bl_len);
+	if (csd->read_bl_partial)
+		puts("Supports partial reads\n");
+	else
+		puts("Does not support partial reads\n");
+	printf("Write block length:      %u\n", 1 << csd->write_bl_len);
+	if (csd->write_bl_partial)
+		puts("Supports partial writes\n");
+	else
+		puts("Does not support partial writes\n");
+	if (csd->wp_grp_enable)
+		printf("Supports group WP:      %u\n", csd->wp_grp_size + 1);
+	else
+		puts("Does not support group WP\n");
+	printf("Card capacity:		%u bytes\n",
+	       (csd->c_size + 1) * (1 << (csd->c_size_mult + 2)) *
+	       (1 << csd->read_bl_len));
+	printf("File format:            %u/%u\n",
+	       csd->file_format_grp, csd->file_format);
+	puts("Write protection:        ");
+	if (csd->perm_write_protect)
+		puts(" permanent");
+	if (csd->tmp_write_protect)
+		puts(" temporary");
+	putc('\n');
+}
+
+static int mmc_idle_cards(void)
+{
+	int ret;
+
+	/* Reset and initialize all cards */
+	ret = mmc_cmd(MMC_CMD_GO_IDLE_STATE, 0, NULL, 0);
+	if (ret)
+		return ret;
+
+	/* Keep the bus idle for 74 clock cycles */
+	return mmc_cmd(0, 0, NULL, INIT_CMD);
+}
+
+static int sd_init_card(struct mmc_cid *cid, int verbose)
+{
+	unsigned long resp[4];
+	int i, ret = 0;
+
+	mmc_idle_cards();
+	for (i = 0; i < 1000; i++) {
+		ret = mmc_acmd(MMC_ACMD_SD_SEND_OP_COND, CFG_MMC_OP_COND,
+			       resp, R3 | NID);
+		if (ret || (resp[0] & 0x80000000))
+			break;
+		ret = -ETIMEDOUT;
+	}
+
+	if (ret)
+		return ret;
+
+	ret = mmc_cmd(MMC_CMD_ALL_SEND_CID, 0, resp, R2 | NID);
+	if (ret)
+		return ret;
+	sd_parse_cid(cid, resp);
+	if (verbose)
+		mmc_dump_cid(cid);
+
+	/* Get RCA of the card that responded */
+	ret = mmc_cmd(MMC_CMD_SD_SEND_RELATIVE_ADDR, 0, resp, R6 | NCR);
+	if (ret)
+		return ret;
+
+	mmc_rca = resp[0] >> 16;
+	if (verbose)
+		printf("SD Card detected (RCA %u)\n", mmc_rca);
+	return 0;
+}
+
+static int mmc_init_card(struct mmc_cid *cid, int verbose)
+{
+	unsigned long resp[4];
+	int i, ret = 0;
+
+	mmc_idle_cards();
+	for (i = 0; i < 1000; i++) {
+		ret = mmc_cmd(MMC_CMD_SEND_OP_COND, CFG_MMC_OP_COND, resp,
+			      R3 | NID | OPEN_DRAIN);
+		if (ret || (resp[0] & 0x80000000))
+			break;
+		ret = -ETIMEDOUT;
+	}
+
+	if (ret)
+		return ret;
+
+	/* Get CID of all cards. FIXME: Support more than one card */
+	ret = mmc_cmd(MMC_CMD_ALL_SEND_CID, 0, resp, R2 | NID | OPEN_DRAIN);
+	if (ret)
+		return ret;
+	mmc_parse_cid(cid, resp);
+	if (verbose)
+		mmc_dump_cid(cid);
+
+	/* Set Relative Address of the card that responded */
+	ret = mmc_cmd(MMC_CMD_SET_RELATIVE_ADDR, mmc_rca << 16, resp,
+		      R1 | NCR | OPEN_DRAIN);
+	return ret;
+}
+
+int mmc_init(int verbose)
+{
+	struct mmc_cid cid;
+	struct mmc_csd csd;
+	int ret;
+
+	/* Initialize controller */
+	mmci_writel(CR, MMCI_BIT(SWRST));
+	mmci_writel(CR, MMCI_BIT(MCIEN));
+	mmci_writel(DTOR, 0x5f);
+	mmci_writel(IDR, ~0UL);
+	mci_set_mode(CFG_MMC_CLK_OD, MMC_DEFAULT_BLKLEN);
+
+	ret = sd_init_card(&cid, verbose);
+	if (ret) {
+		mmc_rca = MMC_DEFAULT_RCA;
+		ret = mmc_init_card(&cid, verbose);
+	}
+	if (ret)
+		return ret;
+
+	/* Get CSD from the card */
+	ret = mmc_cmd(MMC_CMD_SEND_CSD, mmc_rca << 16, &csd, R2 | NCR);
+	if (ret)
+		return ret;
+	if (verbose)
+		mmc_dump_csd(&csd);
+
+	/* Initialize the blockdev structure */
+	mmc_blkdev.if_type = IF_TYPE_MMC;
+	mmc_blkdev.part_type = PART_TYPE_DOS;
+	mmc_blkdev.block_read = mmc_bread;
+	sprintf((char *)mmc_blkdev.vendor,
+		"Man %02x%04x Snr %08x",
+		cid.mid, cid.oid, cid.psn);
+	strncpy((char *)mmc_blkdev.product, cid.pnm,
+		sizeof(mmc_blkdev.product));
+	sprintf((char *)mmc_blkdev.revision, "%x %x",
+		cid.prv >> 4, cid.prv & 0x0f);
+	mmc_blkdev.blksz = 1 << csd.read_bl_len;
+	mmc_blkdev.lba = (csd.c_size + 1) * (1 << (csd.c_size_mult + 2));
+
+	mci_set_mode(CFG_MMC_CLK_PP, mmc_blkdev.blksz);
+
+#if 0
+	if (fat_register_device(&mmc_blkdev, 1))
+		printf("Could not register MMC fat device\n");
+#else
+	init_part(&mmc_blkdev);
+#endif
+
+	return 0;
+}
+
+int mmc_read(ulong src, uchar *dst, int size)
+{
+	return -ENOSYS;
+}
+
+int mmc_write(uchar *src, ulong dst, int size)
+{
+	return -ENOSYS;
+}
+
+int mmc2info(ulong addr)
+{
+	return 0;
+}
+
+#endif /* CONFIG_MMC */

cpu/at32ap/atmel_mci.h

@@ -0,0 +1,197 @@
+/*
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef __CPU_AT32AP_ATMEL_MCI_H__
+#define __CPU_AT32AP_ATMEL_MCI_H__
+
+/* Atmel MultiMedia Card Interface (MCI) registers */
+#define MMCI_CR					0x0000
+#define MMCI_MR					0x0004
+#define MMCI_DTOR				0x0008
+#define MMCI_SDCR				0x000c
+#define MMCI_ARGR				0x0010
+#define MMCI_CMDR				0x0014
+#define MMCI_RSPR				0x0020
+#define MMCI_RSPR1				0x0024
+#define MMCI_RSPR2				0x0028
+#define MMCI_RSPR3				0x002c
+#define MMCI_RDR				0x0030
+#define MMCI_TDR				0x0034
+#define MMCI_SR					0x0040
+#define MMCI_IER				0x0044
+#define MMCI_IDR				0x0048
+#define MMCI_IMR				0x004c
+
+/* Bitfields in CR */
+#define MMCI_MCIEN_OFFSET			0
+#define MMCI_MCIEN_SIZE				1
+#define MMCI_MCIDIS_OFFSET			1
+#define MMCI_MCIDIS_SIZE			1
+#define MMCI_PWSEN_OFFSET			2
+#define MMCI_PWSEN_SIZE				1
+#define MMCI_PWSDIS_OFFSET			3
+#define MMCI_PWSDIS_SIZE			1
+#define MMCI_SWRST_OFFSET			7
+#define MMCI_SWRST_SIZE				1
+
+/* Bitfields in MR */
+#define MMCI_CLKDIV_OFFSET			0
+#define MMCI_CLKDIV_SIZE			8
+#define MMCI_PWSDIV_OFFSET			8
+#define MMCI_PWSDIV_SIZE			3
+#define MMCI_PDCPADV_OFFSET			14
+#define MMCI_PDCPADV_SIZE			1
+#define MMCI_PDCMODE_OFFSET			15
+#define MMCI_PDCMODE_SIZE			1
+#define MMCI_BLKLEN_OFFSET			16
+#define MMCI_BLKLEN_SIZE			16
+
+/* Bitfields in DTOR */
+#define MMCI_DTOCYC_OFFSET			0
+#define MMCI_DTOCYC_SIZE			4
+#define MMCI_DTOMUL_OFFSET			4
+#define MMCI_DTOMUL_SIZE			3
+
+/* Bitfields in SDCR */
+#define MMCI_SCDSEL_OFFSET			0
+#define MMCI_SCDSEL_SIZE			4
+#define MMCI_SCDBUS_OFFSET			7
+#define MMCI_SCDBUS_SIZE			1
+
+/* Bitfields in ARGR */
+#define MMCI_ARG_OFFSET				0
+#define MMCI_ARG_SIZE				32
+
+/* Bitfields in CMDR */
+#define MMCI_CMDNB_OFFSET			0
+#define MMCI_CMDNB_SIZE				6
+#define MMCI_RSPTYP_OFFSET			6
+#define MMCI_RSPTYP_SIZE			2
+#define MMCI_SPCMD_OFFSET			8
+#define MMCI_SPCMD_SIZE				3
+#define MMCI_OPDCMD_OFFSET			11
+#define MMCI_OPDCMD_SIZE			1
+#define MMCI_MAXLAT_OFFSET			12
+#define MMCI_MAXLAT_SIZE			1
+#define MMCI_TRCMD_OFFSET			16
+#define MMCI_TRCMD_SIZE				2
+#define MMCI_TRDIR_OFFSET			18
+#define MMCI_TRDIR_SIZE				1
+#define MMCI_TRTYP_OFFSET			19
+#define MMCI_TRTYP_SIZE				2
+
+/* Bitfields in RSPRx */
+#define MMCI_RSP_OFFSET				0
+#define MMCI_RSP_SIZE				32
+
+/* Bitfields in SR/IER/IDR/IMR */
+#define MMCI_CMDRDY_OFFSET			0
+#define MMCI_CMDRDY_SIZE			1
+#define MMCI_RXRDY_OFFSET			1
+#define MMCI_RXRDY_SIZE				1
+#define MMCI_TXRDY_OFFSET			2
+#define MMCI_TXRDY_SIZE				1
+#define MMCI_BLKE_OFFSET			3
+#define MMCI_BLKE_SIZE				1
+#define MMCI_DTIP_OFFSET			4
+#define MMCI_DTIP_SIZE				1
+#define MMCI_NOTBUSY_OFFSET			5
+#define MMCI_NOTBUSY_SIZE			1
+#define MMCI_ENDRX_OFFSET			6
+#define MMCI_ENDRX_SIZE				1
+#define MMCI_ENDTX_OFFSET			7
+#define MMCI_ENDTX_SIZE				1
+#define MMCI_RXBUFF_OFFSET			14
+#define MMCI_RXBUFF_SIZE			1
+#define MMCI_TXBUFE_OFFSET			15
+#define MMCI_TXBUFE_SIZE			1
+#define MMCI_RINDE_OFFSET			16
+#define MMCI_RINDE_SIZE				1
+#define MMCI_RDIRE_OFFSET			17
+#define MMCI_RDIRE_SIZE				1
+#define MMCI_RCRCE_OFFSET			18
+#define MMCI_RCRCE_SIZE				1
+#define MMCI_RENDE_OFFSET			19
+#define MMCI_RENDE_SIZE				1
+#define MMCI_RTOE_OFFSET			20
+#define MMCI_RTOE_SIZE				1
+#define MMCI_DCRCE_OFFSET			21
+#define MMCI_DCRCE_SIZE				1
+#define MMCI_DTOE_OFFSET			22
+#define MMCI_DTOE_SIZE				1
+#define MMCI_OVRE_OFFSET			30
+#define MMCI_OVRE_SIZE				1
+#define MMCI_UNRE_OFFSET			31
+#define MMCI_UNRE_SIZE				1
+
+/* Constants for DTOMUL */
+#define MMCI_DTOMUL_1_CYCLE			0
+#define MMCI_DTOMUL_16_CYCLES			1
+#define MMCI_DTOMUL_128_CYCLES			2
+#define MMCI_DTOMUL_256_CYCLES			3
+#define MMCI_DTOMUL_1024_CYCLES			4
+#define MMCI_DTOMUL_4096_CYCLES			5
+#define MMCI_DTOMUL_65536_CYCLES		6
+#define MMCI_DTOMUL_1048576_CYCLES		7
+
+/* Constants for RSPTYP */
+#define MMCI_RSPTYP_NO_RESP			0
+#define MMCI_RSPTYP_48_BIT_RESP			1
+#define MMCI_RSPTYP_136_BIT_RESP		2
+
+/* Constants for SPCMD */
+#define MMCI_SPCMD_NO_SPEC_CMD			0
+#define MMCI_SPCMD_INIT_CMD			1
+#define MMCI_SPCMD_SYNC_CMD			2
+#define MMCI_SPCMD_INT_CMD			4
+#define MMCI_SPCMD_INT_RESP			5
+
+/* Constants for TRCMD */
+#define MMCI_TRCMD_NO_TRANS			0
+#define MMCI_TRCMD_START_TRANS			1
+#define MMCI_TRCMD_STOP_TRANS			2
+
+/* Constants for TRTYP */
+#define MMCI_TRTYP_BLOCK			0
+#define MMCI_TRTYP_MULTI_BLOCK			1
+#define MMCI_TRTYP_STREAM			2
+
+/* Bit manipulation macros */
+#define MMCI_BIT(name)					\
+	(1 << MMCI_##name##_OFFSET)
+#define MMCI_BF(name,value)				\
+	(((value) & ((1 << MMCI_##name##_SIZE) - 1))	\
+	 << MMCI_##name##_OFFSET)
+#define MMCI_BFEXT(name,value)				\
+	(((value) >> MMCI_##name##_OFFSET)\
+	 & ((1 << MMCI_##name##_SIZE) - 1))
+#define MMCI_BFINS(name,value,old)			\
+	(((old) & ~(((1 << MMCI_##name##_SIZE) - 1)	\
+		    << MMCI_##name##_OFFSET))		\
+	 | MMCI_BF(name,value))
+
+/* Register access macros */
+#define mmci_readl(reg)					\
+	readl((void *)MMCI_BASE + MMCI_##reg)
+#define mmci_writel(reg,value)				\
+	writel((value), (void *)MMCI_BASE + MMCI_##reg)
+
+#endif /* __CPU_AT32AP_ATMEL_MCI_H__ */

cpu/at32ap/cpu.c

@@ -26,33 +26,79 @@
 #include <asm/sections.h>
 #include <asm/sysreg.h>
 
+#include <asm/arch/clk.h>
 #include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
 
 #include "hsmc3.h"
+#include "sm.h"
+
+/* Sanity checks */
+#if (CFG_CLKDIV_CPU > CFG_CLKDIV_HSB)		\
+	|| (CFG_CLKDIV_HSB > CFG_CLKDIV_PBA)	\
+	|| (CFG_CLKDIV_HSB > CFG_CLKDIV_PBB)
+# error Constraint fCPU >= fHSB >= fPB{A,B} violated
+#endif
+#if defined(CONFIG_PLL) && ((CFG_PLL0_MUL < 1) || (CFG_PLL0_DIV < 1))
+# error Invalid PLL multiplier and/or divider
+#endif
 
 DECLARE_GLOBAL_DATA_PTR;
 
+static void pm_init(void)
+{
+	uint32_t cksel;
+
+#ifdef CONFIG_PLL
+	/* Initialize the PLL */
+	sm_writel(PM_PLL0, (SM_BF(PLLCOUNT, CFG_PLL0_SUPPRESS_CYCLES)
+			    | SM_BF(PLLMUL, CFG_PLL0_MUL - 1)
+			    | SM_BF(PLLDIV, CFG_PLL0_DIV - 1)
+			    | SM_BF(PLLOPT, CFG_PLL0_OPT)
+			    | SM_BF(PLLOSC, 0)
+			    | SM_BIT(PLLEN)));
+
+	/* Wait for lock */
+	while (!(sm_readl(PM_ISR) & SM_BIT(LOCK0))) ;
+#endif
+
+	/* Set up clocks for the CPU and all peripheral buses */
+	cksel = 0;
+	if (CFG_CLKDIV_CPU)
+		cksel |= SM_BIT(CPUDIV) | SM_BF(CPUSEL, CFG_CLKDIV_CPU - 1);
+	if (CFG_CLKDIV_HSB)
+		cksel |= SM_BIT(HSBDIV) | SM_BF(HSBSEL, CFG_CLKDIV_HSB - 1);
+	if (CFG_CLKDIV_PBA)
+		cksel |= SM_BIT(PBADIV) | SM_BF(PBASEL, CFG_CLKDIV_PBA - 1);
+	if (CFG_CLKDIV_PBB)
+		cksel |= SM_BIT(PBBDIV) | SM_BF(PBBSEL, CFG_CLKDIV_PBB - 1);
+	sm_writel(PM_CKSEL, cksel);
+
+	gd->cpu_hz = get_cpu_clk_rate();
+
+#ifdef CONFIG_PLL
+	/* Use PLL0 as main clock */
+	sm_writel(PM_MCCTRL, SM_BIT(PLLSEL));
+#endif
+}
+
 int cpu_init(void)
 {
-	const struct device *hebi;
 	extern void _evba(void);
 	char *p;
 
 	gd->cpu_hz = CFG_OSC0_HZ;
 
-	/* fff03400: 00010001 04030402 00050005 10011103 */
-	hebi = get_device(DEVICE_HEBI);
-	hsmc3_writel(hebi, MODE0, 0x00031103);
-	hsmc3_writel(hebi, CYCLE0, 0x000c000d);
-	hsmc3_writel(hebi, PULSE0, 0x0b0a0906);
-	hsmc3_writel(hebi, SETUP0, 0x00010002);
+	/* TODO: Move somewhere else, but needs to be run before we
+	 * increase the clock frequency. */
+	hsmc3_writel(MODE0, 0x00031103);
+	hsmc3_writel(CYCLE0, 0x000c000d);
+	hsmc3_writel(PULSE0, 0x0b0a0906);
+	hsmc3_writel(SETUP0, 0x00010002);
 
 	pm_init();
 
 	sysreg_write(EVBA, (unsigned long)&_evba);
 	asm volatile("csrf	%0" : : "i"(SYSREG_EM_OFFSET));
-	gd->console_uart = get_device(CFG_CONSOLE_UART_DEV);
 
 	/* Lock everything that mess with the flash in the icache */
 	for (p = __flashprog_start; p <= (__flashprog_end + CFG_ICACHE_LINESZ);

cpu/at32ap/device.c

@@ -1,126 +0,0 @@
-/*
- * Copyright (C) 2006 Atmel Corporation
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-#include <common.h>
-
-#include <asm/arch/platform.h>
-
-#include "sm.h"
-
-struct device_state {
-	int refcount;
-};
-
-static struct device_state device_state[NR_DEVICES];
-
-static int claim_resource(const struct resource *res)
-{
-	int ret = 0;
-
-	switch (res->type) {
-	case RESOURCE_GPIO:
-		ret = gpio_set_func(res->u.gpio.gpio_dev,
-				    res->u.gpio.start,
-				    res->u.gpio.nr_pins,
-				    res->u.gpio.func);
-		break;
-	case RESOURCE_CLOCK:
-		ret = pm_enable_clock(res->u.clock.id, res->u.clock.index);
-		break;
-	}
-
-	return ret;
-}
-
-static void free_resource(const struct resource *res)
-{
-	switch (res->type) {
-	case RESOURCE_GPIO:
-		gpio_free(res->u.gpio.gpio_dev, res->u.gpio.start,
-			  res->u.gpio.nr_pins);
-		break;
-	case RESOURCE_CLOCK:
-		pm_disable_clock(res->u.clock.id, res->u.clock.index);
-		break;
-	}
-}
-
-static int init_dev(const struct device *dev)
-{
-	unsigned int i;
-	int ret = 0;
-
-	for (i = 0; i < dev->nr_resources; i++) {
-		ret = claim_resource(&dev->resource[i]);
-		if (ret)
-			goto cleanup;
-	}
-
-	return 0;
-
-cleanup:
-	while (i--)
-		free_resource(&dev->resource[i]);
-
-	return ret;
-}
-
-const struct device *get_device(enum device_id devid)
-{
-	struct device_state *devstate;
-	const struct device *dev;
-	unsigned long flags;
-	int initialized = 0;
-	int ret = 0;
-
-	devstate = &device_state[devid];
-	dev = &chip_device[devid];
-
-	flags = disable_interrupts();
-	if (devstate->refcount++)
-		initialized = 1;
-	if (flags)
-		enable_interrupts();
-
-	if (!initialized)
-		ret = init_dev(dev);
-
-	return ret ? NULL : dev;
-}
-
-void put_device(const struct device *dev)
-{
-	struct device_state *devstate;
-	unsigned long devid, flags;
-
-	devid = (unsigned long)(dev - chip_device) / sizeof(struct device);
-	devstate = &device_state[devid];
-
-	flags = disable_interrupts();
-	devstate--;
-	if (!devstate) {
-		unsigned int i;
-		for (i = 0; i < dev->nr_resources; i++)
-			free_resource(&dev->resource[i]);
-	}
-	if (flags)
-		enable_interrupts();
-}

cpu/at32ap/entry.S

@@ -42,8 +42,7 @@ timer_interrupt_handler:
 	 * We're running at interrupt level 3, so we don't need to save
 	 * r8-r12 or lr to the stack.
 	 */
-	mov	r8, lo(timer_overflow)
-	orh	r8, hi(timer_overflow)
+	lda.w	r8, timer_overflow
 	ld.w	r9, r8[0]
 	mov	r10, -1
 	mtsr	SYSREG_COMPARE, r10

cpu/at32ap/exception.c

@@ -24,6 +24,8 @@
 #include <asm/sysreg.h>
 #include <asm/ptrace.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 static const char * const cpu_modes[8] = {
 	"Application", "Supervisor", "Interrupt level 0", "Interrupt level 1",
 	"Interrupt level 2", "Interrupt level 3", "Exception", "NMI"
@@ -109,11 +111,10 @@ void do_unknown_exception(unsigned int ecr, struct pt_regs *regs)
 	printf("CPU Mode: %s\n", cpu_modes[mode]);
 
 	/* Avoid exception loops */
-	if (regs->sp >= CFG_INIT_SP_ADDR
-	    || regs->sp < (CFG_INIT_SP_ADDR - CONFIG_STACKSIZE))
+	if (regs->sp < CFG_SDRAM_BASE || regs->sp >= gd->stack_end)
 		printf("\nStack pointer seems bogus, won't do stack dump\n");
 	else
-		dump_mem("\nStack: ", regs->sp, CFG_INIT_SP_ADDR);
+		dump_mem("\nStack: ", regs->sp, gd->stack_end);
 
 	panic("Unhandled exception\n");
 }

cpu/at32ap/hsdramc.c

@@ -25,17 +25,11 @@
 #include <asm/io.h>
 #include <asm/sdram.h>
 
-#include <asm/arch/platform.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/memory-map.h>
 
 #include "hsdramc1.h"
 
-struct hsdramc {
-	const struct device *hebi;
-	void *regs;
-};
-
-static struct hsdramc hsdramc;
-
 unsigned long sdram_init(const struct sdram_info *info)
 {
 	unsigned long *sdram = (unsigned long *)uncached(info->phys_addr);
@@ -44,16 +38,6 @@ unsigned long sdram_init(const struct sdram_info *info)
 	unsigned long bus_hz;
 	unsigned int i;
 
-	hsdramc.hebi = get_device(DEVICE_HEBI);
-	if (!hsdramc.hebi)
-		return 0;
-
-	/* FIXME: Both of these lines are complete hacks */
-	hsdramc.regs = hsdramc.hebi->regs + 0x400;
-	bus_hz = pm_get_clock_freq(hsdramc.hebi->resource[0].u.clock.id);
-
-	cpu_enable_sdram();
-
 	tmp = (HSDRAMC1_BF(NC, info->col_bits - 8)
 	       | HSDRAMC1_BF(NR, info->row_bits - 11)
 	       | HSDRAMC1_BF(NB, info->bank_bits - 1)
@@ -74,7 +58,7 @@ unsigned long sdram_init(const struct sdram_info *info)
 			   + info->bank_bits + 2);
 #endif
 
-	hsdramc1_writel(&hsdramc, CR, tmp);
+	hsdramc1_writel(CR, tmp);
 
 	/*
 	 * Initialization sequence for SDRAM, from the data sheet:
@@ -87,15 +71,15 @@ unsigned long sdram_init(const struct sdram_info *info)
 	/*
 	 * 2. A Precharge All command is issued to the SDRAM
 	 */
-	hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_BANKS_PRECHARGE);
-	hsdramc1_readl(&hsdramc, MR);
+	hsdramc1_writel(MR, HSDRAMC1_MODE_BANKS_PRECHARGE);
+	hsdramc1_readl(MR);
 	writel(0, sdram);
 
 	/*
 	 * 3. Eight auto-refresh (CBR) cycles are provided
 	 */
-	hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_AUTO_REFRESH);
-	hsdramc1_readl(&hsdramc, MR);
+	hsdramc1_writel(MR, HSDRAMC1_MODE_AUTO_REFRESH);
+	hsdramc1_readl(MR);
 	for (i = 0; i < 8; i++)
 		writel(0, sdram);
 
@@ -106,8 +90,8 @@ unsigned long sdram_init(const struct sdram_info *info)
 	 *
 	 * CAS from info struct, burst length 1, serial burst type
 	 */
-	hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_LOAD_MODE);
-	hsdramc1_readl(&hsdramc, MR);
+	hsdramc1_writel(MR, HSDRAMC1_MODE_LOAD_MODE);
+	hsdramc1_readl(MR);
 	writel(0, sdram + (info->cas << 4));
 
 	/*
@@ -117,9 +101,9 @@ unsigned long sdram_init(const struct sdram_info *info)
 	 * From the timing diagram, it looks like tMRD is 3
 	 * cycles...try a dummy read from the peripheral bus.
 	 */
-	hsdramc1_readl(&hsdramc, MR);
-	hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_NORMAL);
-	hsdramc1_readl(&hsdramc, MR);
+	hsdramc1_readl(MR);
+	hsdramc1_writel(MR, HSDRAMC1_MODE_NORMAL);
+	hsdramc1_readl(MR);
 	writel(0, sdram);
 
 	/*
@@ -128,7 +112,8 @@ unsigned long sdram_init(const struct sdram_info *info)
 	 *
 	 * 15.6 us is a typical value for a burst of length one
 	 */
-	hsdramc1_writel(&hsdramc, TR, (156 * (bus_hz / 1000)) / 10000);
+	bus_hz = get_sdram_clk_rate();
+	hsdramc1_writel(TR, (156 * (bus_hz / 1000)) / 10000);
 
 	printf("SDRAM: %u MB at address 0x%08lx\n",
 	       sdram_size >> 20, info->phys_addr);

cpu/at32ap/hsdramc1.h

@@ -135,9 +135,9 @@
 	 | HSDRAMC1_BF(name,value))
 
 /* Register access macros */
-#define hsdramc1_readl(port,reg)				\
-	readl((port)->regs + HSDRAMC1_##reg)
-#define hsdramc1_writel(port,reg,value)				\
-	writel((value), (port)->regs + HSDRAMC1_##reg)
+#define hsdramc1_readl(reg)					\
+	readl((void *)HSDRAMC_BASE + HSDRAMC1_##reg)
+#define hsdramc1_writel(reg,value)				\
+	writel((value), (void *)HSDRAMC_BASE + HSDRAMC1_##reg)
 
 #endif /* __ASM_AVR32_HSDRAMC1_H__ */

cpu/at32ap/hsmc3.h

@@ -118,9 +118,9 @@
 	 | HSMC3_BF(name,value))
 
 /* Register access macros */
-#define hsmc3_readl(port,reg)					\
-	readl((port)->regs + HSMC3_##reg)
-#define hsmc3_writel(port,reg,value)				\
-	writel((value), (port)->regs + HSMC3_##reg)
+#define hsmc3_readl(reg)					\
+	readl((void *)HSMC_BASE + HSMC3_##reg)
+#define hsmc3_writel(reg,value)					\
+	writel((value), (void *)HSMC_BASE + HSMC3_##reg)
 
 #endif /* __CPU_AT32AP_HSMC3_H__ */

cpu/at32ap/interrupts.c

@@ -27,7 +27,7 @@
 #include <asm/processor.h>
 #include <asm/sysreg.h>
 
-#include <asm/arch/platform.h>
+#include <asm/arch/memory-map.h>
 
 #define HANDLER_MASK	0x00ffffff
 #define INTLEV_SHIFT	30
@@ -44,8 +44,6 @@ volatile unsigned long timer_overflow;
  */
 static unsigned long tb_factor;
 
-static const struct device *intc_dev;
-
 unsigned long get_tbclk(void)
 {
 	return gd->cpu_hz;
@@ -117,16 +115,19 @@ void udelay(unsigned long usec)
 static int set_interrupt_handler(unsigned int nr, void (*handler)(void),
 				 unsigned int priority)
 {
+	extern void _evba(void);
 	unsigned long intpr;
 	unsigned long handler_addr = (unsigned long)handler;
 
+	handler_addr -= (unsigned long)&_evba;
+
 	if ((handler_addr & HANDLER_MASK) != handler_addr
 	    || (priority & INTLEV_MASK) != priority)
 		return -EINVAL;
 
 	intpr = (handler_addr & HANDLER_MASK);
 	intpr |= (priority & INTLEV_MASK) << INTLEV_SHIFT;
-	writel(intpr, intc_dev->regs + 4 * nr);
+	writel(intpr, (void *)INTC_BASE + 4 * nr);
 
 	return 0;
 }
@@ -143,10 +144,7 @@ void timer_init(void)
 	do_div(tmp, gd->cpu_hz);
 	tb_factor = (u32)tmp;
 
-	intc_dev = get_device(DEVICE_INTC);
-
-	if (!intc_dev
-	    || set_interrupt_handler(0, &timer_interrupt_handler, 3))
+	if (set_interrupt_handler(0, &timer_interrupt_handler, 3))
 		return;
 
 	/* For all practical purposes, this gives us an overflow interrupt */

cpu/at32ap/pio.c

@@ -21,74 +21,40 @@
  */
 #include <common.h>
 
-#include <asm/errno.h>
 #include <asm/io.h>
-#include <asm/arch/platform.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/memory-map.h>
 
 #include "pio2.h"
 
-struct pio_state {
-	const struct device *dev;
-	u32 alloc_mask;
-};
-
-static struct pio_state pio_state[CFG_NR_PIOS];
-
-int gpio_set_func(enum device_id gpio_devid, unsigned int start,
-		  unsigned int nr_pins, enum gpio_func func)
+void gpio_select_periph_A(unsigned int pin, int use_pullup)
 {
-	const struct device *gpio;
-	struct pio_state *state;
-	u32 mask;
-
-	state = &pio_state[gpio_devid - DEVICE_PIOA];
-
-	gpio = get_device(gpio_devid);
-	if (!gpio)
-		return -EBUSY;
-
-	state->dev = gpio;
-	mask = ((1 << nr_pins) - 1) << start;
-
-	if (mask & state->alloc_mask) {
-		put_device(gpio);
-		return -EBUSY;
-	}
-	state->alloc_mask |= mask;
-
-	switch (func) {
-	case GPIO_FUNC_GPIO:
-		/* TODO */
-		return -EINVAL;
-	case GPIO_FUNC_A:
-		pio2_writel(gpio, ASR, mask);
-		pio2_writel(gpio, PDR, mask);
-		pio2_writel(gpio, PUDR, mask);
-		break;
-	case GPIO_FUNC_B:
-		pio2_writel(gpio, BSR, mask);
-		pio2_writel(gpio, PDR, mask);
-		pio2_writel(gpio, PUDR, mask);
-		break;
-	}
-
-	return 0;
+	void *base = gpio_pin_to_addr(pin);
+	uint32_t mask = 1 << (pin & 0x1f);
+
+	if (!base)
+		panic("Invalid GPIO pin %u\n", pin);
+
+	pio2_writel(base, ASR, mask);
+	pio2_writel(base, PDR, mask);
+	if (use_pullup)
+		pio2_writel(base, PUER, mask);
+	else
+		pio2_writel(base, PUDR, mask);
 }
 
-void gpio_free(enum device_id gpio_devid, unsigned int start,
-	       unsigned int nr_pins)
+void gpio_select_periph_B(unsigned int pin, int use_pullup)
 {
-	const struct device *gpio;
-	struct pio_state *state;
-	u32 mask;
-
-	state = &pio_state[gpio_devid - DEVICE_PIOA];
-	gpio = state->dev;
-	mask = ((1 << nr_pins) - 1) << start;
-
-	pio2_writel(gpio, ODR, mask);
-	pio2_writel(gpio, PER, mask);
-
-	state->alloc_mask &= ~mask;
-	put_device(gpio);
+	void *base = gpio_pin_to_addr(pin);
+	uint32_t mask = 1 << (pin & 0x1f);
+
+	if (!base)
+		panic("Invalid GPIO pin %u\n", pin);
+
+	pio2_writel(base, BSR, mask);
+	pio2_writel(base, PDR, mask);
+	if (use_pullup)
+		pio2_writel(base, PUER, mask);
+	else
+		pio2_writel(base, PUDR, mask);
 }

cpu/at32ap/pio2.h

@@ -36,9 +36,9 @@
 #define PIO2_OWSR				0x00a8
 
 /* Register access macros */
-#define pio2_readl(port,reg)				\
-	readl((port)->regs + PIO2_##reg)
-#define pio2_writel(port,reg,value)			\
-	writel((value), (port)->regs + PIO2_##reg)
+#define pio2_readl(base,reg)				\
+	readl((void *)base + PIO2_##reg)
+#define pio2_writel(base,reg,value)			\
+	writel((value), (void *)base + PIO2_##reg)
 
 #endif /* __CPU_AT32AP_PIO2_H__ */

cpu/at32ap/pm.c

@@ -26,138 +26,17 @@
 #include <asm/io.h>
 
 #include <asm/arch/memory-map.h>
-#include <asm/arch/platform.h>
 
 #include "sm.h"
 
-/* Sanity checks */
-#if (CFG_CLKDIV_CPU > CFG_CLKDIV_HSB)		\
-	|| (CFG_CLKDIV_HSB > CFG_CLKDIV_PBA)	\
-	|| (CFG_CLKDIV_HSB > CFG_CLKDIV_PBB)
-# error Constraint fCPU >= fHSB >= fPB{A,B} violated
-#endif
-#if defined(CONFIG_PLL) && ((CFG_PLL0_MUL < 1) || (CFG_PLL0_DIV < 1))
-# error Invalid PLL multiplier and/or divider
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct clock_domain_state {
-	const struct device *bridge;
-	unsigned long freq;
-	u32 mask;
-};
-static struct clock_domain_state ckd_state[NR_CLOCK_DOMAINS];
-
-int pm_enable_clock(enum clock_domain_id id, unsigned int index)
-{
-	const struct clock_domain *ckd = &chip_clock[id];
-	struct clock_domain_state *state = &ckd_state[id];
-
-	if (ckd->bridge != NO_DEVICE) {
-		state->bridge = get_device(ckd->bridge);
-		if (!state->bridge)
-			return -EBUSY;
-	}
-
-	state->mask |= 1 << index;
-	if (gd->sm)
-		writel(state->mask, gd->sm->regs + ckd->reg);
-
-	return 0;
-}
-
-void pm_disable_clock(enum clock_domain_id id, unsigned int index)
-{
-	const struct clock_domain *ckd = &chip_clock[id];
-	struct clock_domain_state *state = &ckd_state[id];
-
-	state->mask &= ~(1 << index);
-	if (gd->sm)
-		writel(state->mask, gd->sm->regs + ckd->reg);
-
-	if (ckd->bridge)
-		put_device(state->bridge);
-}
-
-unsigned long pm_get_clock_freq(enum clock_domain_id domain)
-{
-	return ckd_state[domain].freq;
-}
-
-void pm_init(void)
-{
-	uint32_t cksel = 0;
-	unsigned long main_clock;
-
-	/* Make sure we don't disable any device we're already using */
-	get_device(DEVICE_HRAMC);
-	get_device(DEVICE_HEBI);
-
-	/* Enable the PICO as well */
-	ckd_state[CLOCK_CPU].mask |= 1;
-
-	gd->sm = get_device(DEVICE_SM);
-	if (!gd->sm)
-		panic("Unable to claim system manager device!\n");
-
-	/* Disable any devices that haven't been explicitly claimed */
-	sm_writel(gd->sm, PM_PBB_MASK, ckd_state[CLOCK_PBB].mask);
-	sm_writel(gd->sm, PM_PBA_MASK, ckd_state[CLOCK_PBA].mask);
-	sm_writel(gd->sm, PM_HSB_MASK, ckd_state[CLOCK_HSB].mask);
-	sm_writel(gd->sm, PM_CPU_MASK, ckd_state[CLOCK_CPU].mask);
 
 #ifdef CONFIG_PLL
-	/* Initialize the PLL */
-	main_clock = (CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL;
-
-	sm_writel(gd->sm, PM_PLL0, (SM_BF(PLLCOUNT, CFG_PLL0_SUPPRESS_CYCLES)
-				    | SM_BF(PLLMUL, CFG_PLL0_MUL - 1)
-				    | SM_BF(PLLDIV, CFG_PLL0_DIV - 1)
-				    | SM_BF(PLLOPT, CFG_PLL0_OPT)
-				    | SM_BF(PLLOSC, 0)
-				    | SM_BIT(PLLEN)));
-
-	/* Wait for lock */
-	while (!(sm_readl(gd->sm, PM_ISR) & SM_BIT(LOCK0))) ;
+#define MAIN_CLK_RATE ((CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL)
 #else
-	main_clock = CFG_OSC0_HZ;
+#define MAIN_CLK_RATE (CFG_OSC0_HZ)
 #endif
 
-	/* Set up clocks for the CPU and all peripheral buses */
-	if (CFG_CLKDIV_CPU) {
-		cksel |= SM_BIT(CPUDIV) | SM_BF(CPUSEL, CFG_CLKDIV_CPU - 1);
-		ckd_state[CLOCK_CPU].freq = main_clock / (1 << CFG_CLKDIV_CPU);
-	} else {
-		ckd_state[CLOCK_CPU].freq = main_clock;
-	}
-	if (CFG_CLKDIV_HSB) {
-		cksel |= SM_BIT(HSBDIV) | SM_BF(HSBSEL, CFG_CLKDIV_HSB - 1);
-		ckd_state[CLOCK_HSB].freq = main_clock / (1 << CFG_CLKDIV_HSB);
-	} else {
-		ckd_state[CLOCK_HSB].freq = main_clock;
-	}
-	if (CFG_CLKDIV_PBA) {
-		cksel |= SM_BIT(PBADIV) | SM_BF(PBASEL, CFG_CLKDIV_PBA - 1);
-		ckd_state[CLOCK_PBA].freq = main_clock / (1 << CFG_CLKDIV_PBA);
-	} else {
-		ckd_state[CLOCK_PBA].freq = main_clock;
-	}
-	if (CFG_CLKDIV_PBB) {
-		cksel |= SM_BIT(PBBDIV) | SM_BF(PBBSEL, CFG_CLKDIV_PBB - 1);
-		ckd_state[CLOCK_PBB].freq = main_clock / (1 << CFG_CLKDIV_PBB);
-	} else {
-		ckd_state[CLOCK_PBB].freq = main_clock;
-	}
-	sm_writel(gd->sm, PM_CKSEL, cksel);
-
-	/* CFG_HZ currently depends on cpu_hz */
-	gd->cpu_hz = ckd_state[CLOCK_CPU].freq;
+DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_PLL
-	/* Use PLL0 as main clock */
-	sm_writel(gd->sm, PM_MCCTRL, SM_BIT(PLLSEL));
-#endif
-}
 
 #endif /* CFG_POWER_MANAGER */

cpu/at32ap/sm.h

@@ -196,9 +196,9 @@
 	 | SM_BF(name,value))
 
 /* Register access macros */
-#define sm_readl(port,reg)				\
-	readl((port)->regs + SM_##reg)
-#define sm_writel(port,reg,value)			\
-	writel((value), (port)->regs + SM_##reg)
+#define sm_readl(reg)					\
+	readl((void *)SM_BASE + SM_##reg)
+#define sm_writel(reg,value)				\
+	writel((value), (void *)SM_BASE + SM_##reg)
 
 #endif /* __CPU_AT32AP_SM_H__ */

cpu/at32ap/start.S

@@ -70,32 +70,12 @@ _start:
 
 2:	lddpc	sp, sp_init
 
-	/*
-	 * Relocate the data section and initialize .bss.  Everything
-	 * is guaranteed to be at least doubleword aligned by the
-	 * linker script.
-	 */
-	lddpc	r12, .Ldata_vma
-	lddpc	r11, .Ldata_lma
-	lddpc	r10, .Ldata_end
-	sub	r10, r12
-4:	ld.d	r8, r11++
-	sub	r10, 8
-	st.d	r12++, r8
-	brne	4b
-
-	mov	r8, 0
-	mov	r9, 0
-	lddpc	r10, .Lbss_end
-	sub	r10, r12
-4:	sub	r10, 8
-	st.d	r12++, r8
-	brne	4b
-
 	/* Initialize the GOT pointer */
 	lddpc	r6, got_init
 3:	rsub	r6, pc
-	ld.w	pc, r6[start_u_boot@got]
+
+	/* Let's go */
+	rjmp	board_init_f
 
 	.align	2
 	.type	sp_init,@object
@@ -103,11 +83,82 @@ sp_init:
 	.long	CFG_INIT_SP_ADDR
 got_init:
 	.long	3b - _GLOBAL_OFFSET_TABLE_
-.Ldata_lma:
-	.long	__data_lma
-.Ldata_vma:
-	.long	_data
-.Ldata_end:
-	.long	_edata
-.Lbss_end:
-	.long	_end
+
+	/*
+	 * void	relocate_code(new_sp, new_gd, monitor_addr)
+	 *
+	 * Relocate the u-boot image into RAM and continue from there.
+	 * Does not return.
+	 */
+	.global	relocate_code
+	.type	relocate_code,@function
+relocate_code:
+	mov	sp, r12		/* use new stack */
+	mov	r12, r11	/* save new_gd */
+	mov	r11, r10	/* save destination address */
+
+	/* copy .text section and flush the cache along the way */
+	lda.w	r8, _text
+	lda.w	r9, _etext
+	sub	lr, r10, r8	/* relocation offset */
+
+1:	ldm	r8++, r0-r3
+	stm	r10, r0-r3
+	sub	r10, -16
+	ldm	r8++, r0-r3
+	stm	r10, r0-r3
+	sub	r10, -16
+	cp.w	r8, r9
+	cache	r10[-4], 0x0d	/* dcache clean/invalidate */
+	cache	r10[-4], 0x01	/* icache invalidate */
+	brlt	1b
+
+	/* flush write buffer */
+	sync	0
+
+	/* copy data sections */
+	lda.w	r9, _edata
+1:	ld.d	r0, r8++
+	st.d	r10++, r0
+	cp.w	r8, r9
+	brlt	1b
+
+	/* zero out .bss */
+	mov	r0, 0
+	mov	r1, 0
+	lda.w	r9, _end
+	sub	r9, r8
+1:	st.d	r10++, r0
+	sub	r9, 8
+	brgt	1b
+
+	/* jump to RAM */
+	sub	r0, pc, . - in_ram
+	add	pc, r0, lr
+
+	.align	2
+in_ram:
+	/* find the new GOT and relocate it */
+	lddpc	r6, got_init_reloc
+3:	rsub	r6, pc
+	mov	r8, r6
+	lda.w	r9, _egot
+	lda.w	r10, _got
+	sub	r9, r10
+1:	ld.w	r0, r8[0]
+	add	r0, lr
+	st.w	r8++, r0
+	sub	r9, 4
+	brgt	1b
+
+	/* Move the exception handlers */
+	mfsr	r2, SYSREG_EVBA
+	add	r2, lr
+	mtsr	SYSREG_EVBA, r2
+
+	/* Do the rest of the initialization sequence */
+	call	board_init_r
+
+	.align	2
+got_init_reloc:
+	.long	3b - _GLOBAL_OFFSET_TABLE_

cpu/bf533/Makefile

@@ -1,6 +1,6 @@
 # U-boot - Makefile
 #
-# Copyright (c) 2005 blackfin.uclinux.org
+# Copyright (c) 2005-2007 Analog Devices Inc.
 #
 # (C) Copyright 2000-2006
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
@@ -20,8 +20,8 @@
 #
 # You should have received a copy of the GNU General Public License
 # along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
+# Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+# MA 02110-1301 USA
 #
 
 include $(TOPDIR)/config.mk

cpu/bf533/bf533_serial.h

@@ -1,7 +1,7 @@
 /*
  * U-boot - bf533_serial.h Serial Driver defines
  *
- * Copyright (c) 2005 blackfin.uclinux.org
+ * Copyright (c) 2005-2007 Analog Devices Inc.
  *
  * This file is based on
  * bf533_serial.h: Definitions for the BlackFin BF533 DSP serial driver.
@@ -38,8 +38,8 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
  */
 
 #ifndef _Bf533_SERIAL_H