ARM: Add support for IGEP COM AQUILA/CYGNUS

The IGEP COM AQUILA and CYGNUS are industrial processors modules with
following highlights:

  o AM3352/AM3354 Texas Instruments processor
  o Cortex-A8 ARM CPU
  o 3.3 volts Inputs / Outputs use industrial
  o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
  o MicroSD card reader on-board
  o Ethernet controller on-board
  o JTAG debug connector available
  o Designed for industrial range purposes

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>

MAINTAINERS

@@ -607,6 +607,7 @@ Enric Balletbo i Serra <eballetbo@iseebcn.com>
 	igep0020	ARM ARMV7 (OMAP3xx SoC)
 	igep0030	ARM ARMV7 (OMAP3xx SoC)
 	igep0032	ARM ARMV7 (OMAP3xx SoC)
+	igep0033	ARM ARMV7 (AM33xx Soc)
 
 Eric Benard <eric@eukrea.com>
 

board/isee/igep0033/Makefile

@@ -0,0 +1,46 @@
+#
+# Makefile
+#
+# Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed "as is" WITHOUT ANY WARRANTY of any
+# kind, whether express or implied; without even the implied warranty
+# of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifdef CONFIG_SPL_BUILD
+COBJS	:= mux.o
+endif
+
+COBJS	+= board.o
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################

board/isee/igep0033/board.c

@@ -0,0 +1,232 @@
+/*
+ * Board functions for IGEP COM AQUILA/CYGNUS based boards
+ *
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
+#ifdef CONFIG_SPL_BUILD
+static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
+#endif
+
+/* MII mode defines */
+#define RMII_MODE_ENABLE	0x4D
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+/* UART Defines */
+#ifdef CONFIG_SPL_BUILD
+#define UART_RESET		(0x1 << 1)
+#define UART_CLK_RUNNING_MASK	0x1
+#define UART_SMART_IDLE_EN	(0x1 << 0x3)
+
+static void rtc32k_enable(void)
+{
+	struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
+
+	/*
+	 * Unlock the RTC's registers.  For more details please see the
+	 * RTC_SS section of the TRM.  In order to unlock we need to
+	 * write these specific values (keys) in this order.
+	 */
+	writel(0x83e70b13, &rtc->kick0r);
+	writel(0x95a4f1e0, &rtc->kick1r);
+
+	/* Enable the RTC 32K OSC by setting bits 3 and 6. */
+	writel((1 << 3) | (1 << 6), &rtc->osc);
+}
+
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = K4B2G1646EBIH9_RD_DQS,
+	.datawdsratio0 = K4B2G1646EBIH9_WR_DQS,
+	.datafwsratio0 = K4B2G1646EBIH9_PHY_FIFO_WE,
+	.datawrsratio0 = K4B2G1646EBIH9_PHY_WR_DATA,
+	.datadldiff0 = PHY_DLL_LOCK_DIFF,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = K4B2G1646EBIH9_RATIO,
+	.cmd0dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF,
+	.cmd0iclkout = K4B2G1646EBIH9_INVERT_CLKOUT,
+
+	.cmd1csratio = K4B2G1646EBIH9_RATIO,
+	.cmd1dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF,
+	.cmd1iclkout = K4B2G1646EBIH9_INVERT_CLKOUT,
+
+	.cmd2csratio = K4B2G1646EBIH9_RATIO,
+	.cmd2dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF,
+	.cmd2iclkout = K4B2G1646EBIH9_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = K4B2G1646EBIH9_EMIF_SDCFG,
+	.ref_ctrl = K4B2G1646EBIH9_EMIF_SDREF,
+	.sdram_tim1 = K4B2G1646EBIH9_EMIF_TIM1,
+	.sdram_tim2 = K4B2G1646EBIH9_EMIF_TIM2,
+	.sdram_tim3 = K4B2G1646EBIH9_EMIF_TIM3,
+	.zq_config = K4B2G1646EBIH9_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = K4B2G1646EBIH9_EMIF_READ_LATENCY,
+};
+#endif
+
+/*
+ * Early system init of muxing and clocks.
+ */
+void s_init(void)
+{
+	/* WDT1 is already running when the bootloader gets control
+	 * Disable it to avoid "random" resets
+	 */
+	writel(0xAAAA, &wdtimer->wdtwspr);
+	while (readl(&wdtimer->wdtwwps) != 0x0)
+		;
+	writel(0x5555, &wdtimer->wdtwspr);
+	while (readl(&wdtimer->wdtwwps) != 0x0)
+		;
+
+#ifdef CONFIG_SPL_BUILD
+	/* Setup the PLLs and the clocks for the peripherals */
+	pll_init();
+
+	/* Enable RTC32K clock */
+	rtc32k_enable();
+
+	/* UART softreset */
+	u32 regval;
+
+	enable_uart0_pin_mux();
+
+	regval = readl(&uart_base->uartsyscfg);
+	regval |= UART_RESET;
+	writel(regval, &uart_base->uartsyscfg);
+	while ((readl(&uart_base->uartsyssts) &
+		UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK)
+		;
+
+	/* Disable smart idle */
+	regval = readl(&uart_base->uartsyscfg);
+	regval |= UART_SMART_IDLE_EN;
+	writel(regval, &uart_base->uartsyscfg);
+
+	gd = &gdata;
+
+	preloader_console_init();
+
+	/* Configure board pin mux */
+	enable_board_pin_mux();
+
+	config_ddr(303, K4B2G1646EBIH9_IOCTRL_VALUE, &ddr3_data,
+		   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+#endif
+}
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+
+	gpmc_init();
+
+	return 0;
+}
+
+#if defined(CONFIG_DRIVER_TI_CPSW)
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+		.phy_if		= PHY_INTERFACE_MODE_RMII,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+	int rv, ret = 0;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+	}
+
+	writel(RMII_MODE_ENABLE, &cdev->miisel);
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0)
+		printf("Error %d registering CPSW switch\n", rv);
+	else
+		ret += rv;
+
+	return ret;
+}
+#endif
+

board/isee/igep0033/board.h

@@ -0,0 +1,27 @@
+/*
+ * IGEP COM AQUILA/CYGNUS boards information header
+ *
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * We must be able to enable uart0, for initial output. We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void enable_board_pin_mux(void);
+#endif

board/isee/igep0033/mux.c

@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},		/* UART0_TXD */
+	{-1},
+};
+
+static struct module_pin_mux mmc0_pin_mux[] = {
+	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT3 */
+	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT2 */
+	{OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT1 */
+	{OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT0 */
+	{OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CLK */
+	{OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CMD */
+	{OFFSET(mcasp0_aclkx), (MODE(4) | RXACTIVE)},		/* MMC0_CD */
+	{-1},
+};
+
+static struct module_pin_mux nand_pin_mux[] = {
+	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
+	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
+	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
+	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
+	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
+	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
+	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
+	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
+	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
+	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},		/* NAND_CS0 */
+	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)},	/* NAND_ADV_ALE */
+	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
+	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
+	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
+	{-1},
+};
+
+static struct module_pin_mux rmii1_pin_mux[] = {
+	{OFFSET(mii1_txen), MODE(1)},			/* RMII1_TXEN */
+	{OFFSET(mii1_rxerr), MODE(1) | RXACTIVE},	/* RMII1_RXERR */
+	{OFFSET(mii1_crs), MODE(1) | RXACTIVE},		/* RMII1_CRS_DV */
+	{OFFSET(mii1_rxd0), MODE(1) | RXACTIVE},	/* RMII1_RXD0 */
+	{OFFSET(mii1_rxd1), MODE(1) | RXACTIVE},	/* RMII1_RXD1 */
+	{OFFSET(mii1_txd0), MODE(1)},			/* RMII1_TXD0 */
+	{OFFSET(mii1_txd1), MODE(1)},			/* RMII1_TXD1 */
+	{OFFSET(rmii1_refclk), MODE(0) | RXACTIVE},	/* RMII1_REF_CLK */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},	/* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+/*
+ * Do board-specific muxes.
+ */
+void enable_board_pin_mux(void)
+{
+	/* NAND Flash */
+	configure_module_pin_mux(nand_pin_mux);
+	/* SD Card */
+	configure_module_pin_mux(mmc0_pin_mux);
+	/* Ethernet pinmux. */
+	configure_module_pin_mux(rmii1_pin_mux);
+}
+

boards.cfg

@@ -277,6 +277,7 @@ igep0020_nand                arm         armv7       igep00x0            isee
 igep0030                     arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_ONENAND
 igep0030_nand                arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_NAND
 igep0032                     arm         armv7       igep00x0            isee           omap3		igep00x0:MACH_TYPE=MACH_TYPE_IGEP0032,BOOT_ONENAND
+igep0033                     arm         armv7       igep0033            isee           am33xx
 am3517_evm                   arm         armv7       am3517evm           logicpd        omap3
 mt_ventoux                   arm         armv7       mt_ventoux          teejet         omap3
 omap3_zoom1                  arm         armv7       zoom1               logicpd        omap3

include/configs/igep0033.h

@@ -0,0 +1,284 @@
+/*
+ * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __CONFIG_IGEP0033_H
+#define __CONFIG_IGEP0033_H
+
+#define CONFIG_AM33XX
+
+#include <asm/arch/omap.h>
+
+/* Mach type */
+#define MACH_TYPE_IGEP0033		4521	/* Until the next sync */
+#define CONFIG_MACH_TYPE		MACH_TYPE_IGEP0033
+
+/* Clock defines */
+#define V_OSCK				24000000  /* Clock output from T2 */
+#define V_SCLK				(V_OSCK)
+
+/* DMA defines */
+#define CONFIG_DMA_COHERENT
+#define CONFIG_DMA_COHERENT_SIZE	(1 << 20)
+
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
+#define CONFIG_SYS_MALLOC_LEN		(1024 << 10)
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT		"U-Boot# "
+#define CONFIG_SYS_NO_FLASH
+
+/* Display cpuinfo */
+#define CONFIG_DISPLAY_CPUINFO
+
+/* Commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+/*
+ * Because the issues explained in doc/README.memory-test, the "mtest command
+ * is considered deprecated. It should not be enabled in most normal ports of
+ * U-Boot.
+ */
+#undef CONFIG_CMD_MEMTEST
+
+#define CONFIG_BOOTDELAY		1	/* negative for no autoboot */
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"loadaddr=0x80200000\0" \
+	"rdaddr=0x81000000\0" \
+	"bootfile=/boot/uImage\0" \
+	"console=ttyO0,115200n8\0" \
+	"optargs=\0" \
+	"mmcdev=0\0" \
+	"mmcroot=/dev/mmcblk0p2 rw\0" \
+	"mmcrootfstype=ext4 rootwait\0" \
+	"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=${rdaddr},64M\0" \
+	"ramrootfstype=ext2\0" \
+	"mmcargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=${mmcroot} " \
+		"rootfstype=${mmcrootfstype}\0" \
+	"bootenv=uEnv.txt\0" \
+	"loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
+	"importbootenv=echo Importing environment from mmc ...; " \
+		"env import -t $loadaddr $filesize\0" \
+	"ramargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=${ramroot} " \
+		"rootfstype=${ramrootfstype}\0" \
+	"loadramdisk=load mmc ${mmcdev} ${rdaddr} ramdisk.gz\0" \
+	"loaduimagefat=load mmc ${mmcdev} ${loadaddr} ${bootfile}\0" \
+	"loaduimage=load mmc ${mmcdev}:2 ${loadaddr} ${bootfile}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"bootm ${loadaddr}\0" \
+	"ramboot=echo Booting from ramdisk ...; " \
+		"run ramargs; " \
+		"bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"mmc dev ${mmcdev}; if mmc rescan; then " \
+		"echo SD/MMC found on device ${mmcdev};" \
+		"if run loadbootenv; then " \
+			"echo Loaded environment from ${bootenv};" \
+			"run importbootenv;" \
+		"fi;" \
+		"if test -n $uenvcmd; then " \
+			"echo Running uenvcmd ...;" \
+			"run uenvcmd;" \
+		"fi;" \
+		"if run loaduimage; then " \
+			"run mmcboot;" \
+		"fi;" \
+	"fi;" \
+
+/* Max number of command args */
+#define CONFIG_SYS_MAXARGS		16
+
+/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE		512
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
+					+ sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_LOAD_ADDR		0x81000000 /* Default load address */
+#define CONFIG_SYS_HZ			1000 /* 1ms clock */
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1		/*  1 bank of DRAM */
+#define PHYS_DRAM_1			0x80000000	/* DRAM Bank #1 */
+#define CONFIG_MAX_RAM_BANK_SIZE	(1024 << 20)	/* 1GB */
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_DRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR         (NON_SECURE_SRAM_END - \
+						GENERATED_GBL_DATA_SIZE)
+/* Platform/Board specific defs */
+#define CONFIG_SYS_TIMERBASE		0x48040000	/* Use Timer2 */
+#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ			1000
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		(48000000)
+#define CONFIG_SYS_NS16550_COM1		0x44e09000	/* UART0 */
+
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+#define CONFIG_ENV_OVERWRITE		1
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+
+/* MMC support */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_DOS_PARTITION
+
+/* GPIO support */
+#define CONFIG_OMAP_GPIO
+
+/* Ethernet support */
+#define CONFIG_DRIVER_TI_CPSW
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT         10
+#define CONFIG_NET_MULTI
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR			0
+#define CONFIG_PHY_SMSC
+
+/* NAND support */
+#define CONFIG_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT	1
+#define CONFIG_SYS_NAND_BASE		(0x08000000)	/* phys address CS0 */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_ONFI_DETECTION	1
+#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		0x260000 /* environment starts here */
+
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+
+#define MTDIDS_DEFAULT			"nand0=nand"
+#define MTDPARTS_DEFAULT		"mtdparts=nand:512k(SPL),"\
+					"1m(U-Boot),128k(U-Boot Env),"\
+					"5m(Kernel),-(File System)"
+
+/* Unsupported features */
+#undef CONFIG_USE_IRQ
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE		0x402F0400
+#define CONFIG_SPL_MAX_SIZE		(101 * 1024)
+#define CONFIG_SPL_STACK		CONFIG_SYS_INIT_SP_ADDR
+
+#define CONFIG_SPL_BSS_START_ADDR	0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME	"u-boot.img"
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_YMODEM_SUPPORT
+#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_NAND_AM33XX_BCH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / \
+					 CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE	2048
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS		{ 2, 3, 4, 5, 6, 7, 8, 9, \
+					 10, 11, 12, 13, 14, 15, 16, 17, \
+					 18, 19, 20, 21, 22, 23, 24, 25, \
+					 26, 27, 28, 29, 30, 31, 32, 33, \
+					 34, 35, 36, 37, 38, 39, 40, 41, \
+					 42, 43, 44, 45, 46, 47, 48, 49, \
+					 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	14
+
+#define CONFIG_SYS_NAND_ECCSTEPS	4
+#define	CONFIG_SYS_NAND_ECCTOTAL	(CONFIG_SYS_NAND_ECCBYTES * \
+						CONFIG_SYS_NAND_ECCSTEPS)
+
+#define	CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
+
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE		0x80800000
+#define CONFIG_SYS_SPL_MALLOC_START	0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
+
+/*
+ * Since SPL did pll and ddr initialization for us,
+ * we don't need to do it twice.
+ */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
+
+#endif	/* ! __CONFIG_IGEP0033_H */