Merge with http://www.denx.de/git/u-boot.git

CHANGELOG

@@ -2,6 +2,256 @@
 Changes since U-Boot 1.1.4:
 ======================================================================
 
+* Enable Quad UART om MCC200 board.
+
+* Cleanup MCC200 board configuration; omit non-existent stuff.
+
+* Add support for MPC859/866 Rev. A.0
+
+* Add command for handling DDR ECC registers on MPC8349EE MDS board.
+
+* Fix DDR ECC bit definitions for MPC83xx.
+
+* Add initial support for MPC8349E MDS board.
+
+* Add support for ECC DDR initialization on MPC83xx.
+
+* Add DMA support for MPC83xx.
+
+* Add sync in do_reset() routine for MPC83xx after RPR register
+  was written to. It is need on some targets when BAT translation
+  is enabled.
+
+* Add bit definitions for MPC83xx DDR controller registers.
+
+* Add Dcbz(), Dcbi() and Dcbf() routines for MPC83xx.
+
+* Correct shift offsets in icache_status and dcache_status for MPC83xx.
+
+* Add support for DS1374 RTC chip.
+
+* Add support for Lite5200B board.
+  Patch by  Patch by Jose Maria (Txema) Lopez, 16 Jan 2006
+
+* Apply SoC concept to arm926ejs CPUs, i.e. move the SoC specific
+  timer and cpu_reset code from cpu/$(CPU) into the new
+  cpu/$(CPU)/$(SOC) directories
+  Patch by Andreas Engel, 13 Mar 2006
+
+* Change max size of uncompressed uImage's to 8MByte and add
+  CFG_BOOTM_LEN to adjust this setting.
+
+  As mentioned by Robin Getz on 2005-05-24 the size of uncompressed
+  uImages was restricted to 4MBytes. This default size is now
+  increased to 8Mbytes and can be overrided by setting CFG_BOOTM_LEN
+  in the board config file.
+
+  Patch by Stefan Roese, 13 Mar 2006
+
+* Fix problem with updated PCI code in cpu/ppc4xx/405gp_pci.c
+  Patch by Stefan Roese, 13 Mar 2006
+
+* cpu/ppc4xx/start.S : exceptions are enabled after relocation
+  Patch by Cedric Vincent, 06 Jul 2005
+
+* au1x00_eth.c: check malloc return value and abort if it failed
+  Patch by Andrew Dyer, 26 Jul 2005
+
+* Change the sequence of events in soft_i2c.c:send_ack() to keep from
+  incorrectly generating start/stop conditions on the bus.
+  Patch by Andrew Dyer, 26 Jul 2005
+
+* Fix bug in [id]cache_status commands for MPC85xx processors;
+  should look at LSB of L1CSRn registers to determine if L1 cache is
+  enabled, not the MSB.
+  Patch by Murray Jensen, 19 Jul 2005
+
+* Fix array overflow with fw_setenv on uninitialised environment
+  Patch by Murray Jensen, 15 Jul 2005
+
+* Add support for EmbeddedPlanet EP88x boards
+  Patch by Yuli Barcohen, 13 Jul 2005
+
+* Remove board specific configuration includes from the common xilinx
+  ethernet and iic adapter code.
+  Patch by Michael Libeskind, 12 Jul 2005
+
+* Add Nat Semi DP83865 PHY support to MPC85xx TSEC driver
+  Patch by Murray Jensen, 08 Jul 2005
+
+* Add (some) definitions for the MPC85xx local bus controller
+  Patch by Murray Jensen, 08 Jul 2005
+
+* Add CPM2 I/O pin functions for MPC85xx processors
+  Patch by Murray Jensen, 08 Jul 2005
+
+* Fix compile problem
+
+* Added PCI support for MPC8349ADS board
+  Patch by Kumar Gala 11 Jan 2006
+
+* Enable address translation on MPC83xx
+  Patch by Kumar Gala, 10 Feb 2006
+
+* Decopuled setting of OR/BR and LBLAWBAR/LBLAWAR on MPC83xx
+  Patch by Kumar Gala, 25 Jan 2006
+
+* Fixed defines for MPC83xx SICRL register to match current specs
+  Patch by Kumar Gala, 23 Jan 2006
+
+* Only disable the MPC83xx watchdog if its enabled out of reset.
+  If its disabled out of reset SW can later enable it if so desired
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Allow config of GPIO direction & data registers at boot on 83xx
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Enable time handling on 83xx
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Make System IO Config Registers board configurable on MPC83xx
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Fixed PCI indirect config ops to handle multiple PCI controllers
+  We need to adjust the bus number we are trying to access based
+  on which PCI controller its on
+  Patch by Kumar Gala, 12 Jan 2006
+
+* Report back PCI bus when doing table based device config
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Added support for PCI prefetchable region and BARs
+  If a host controller sets up a region as prefetchable and
+  a device's BAR denotes it as prefetchable, allocate the
+  BAR into the prefetch region.
+
+  If a BAR is prefetchable and no prefetchable region has
+  been setup by the controller we fall back to allocating
+  the BAR into the normally memory region.
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Add helper function for generic flat device tree fixups for mpc83xx
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for passing initrd information via flat device tree
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Added OF_STDOUT_PATH and OF_SOC
+
+  OF_STDOUT_PATH specifies the path to the device the kernel can use
+  for console output
+
+  OF_SOC specifies the proper name of the SOC node if one exists.
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Allow board code to fixup the flat device tree before booting a kernel
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Added CONFIG_ options for bd_t and env in flat dev tree
+
+	CONFIG_OF_HAS_BD_T will put a copy of the bd_t
+	into the resulting flat device tree.
+
+	CONFIG_OF_HAS_UBOOT_ENV will copy the environment
+	variables from u-boot into the flat device tree
+
+  Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for the DHCP vendor optional bootfile (#67).
+  Ignores the vendor TFTP server name option (#66).
+  Patch by Murray Jensen, 30 Jun 2005
+
+* Fix a HW timing issue on 8548 CDS for eTSEC 3 in RGMII mode
+  Patch by Andy Fleming, 14 Jun 2005
+
+* Fix bad register definitions for LTX971 PHY on MPC85xx boards.
+  Patch by Gerhard Jaeger, 21 Jun 2005
+
+* Add netconsole and some more commands to RPXlite_DW board
+  Patch by Sam Song, 19 Jun 2005
+
+* Fix bad declaration on pci_cfgfunc_nothing
+  Patch by Sam Song, 19 Jun 2005
+
+* Adjust "echo" as a default command
+  Patch by Sam Song, 19 Jun 2005
+
+* Fix PCIDF calculation in cpu/mpc8260/speed.c for MPC8280EC
+  Patch by KokHow Teh, 16 Jun 2005
+
+* Add crc of data to jffs2 (in jffs2_1pass_build_lists()).
+  Patch by Rick Bronson, 15 Jun 2005
+
+* Coding Style cleanup
+
+* Avoid dereferencing NULL in find_cmd() if no valid commands were found
+  Patch by Andrew Dyer, 13 Jun 2005
+
+* Add ADI Blackfin support
+  - add support for Analog Devices Blackfin BF533 CPU
+  - add support for the ADI BF533 Stamp uClinux board
+  - add support for the ADI BF533 EZKit board
+  Patches by Richard Klingler, 11 Jun 2005
+
+* Add loads of ntohl() in image header handling
+  Patch by Steven Scholz, 10 Jun 2005
+
+* Switch MPC86xADS and MPC885ADS boards to use cpuclk environment
+  variable to set clock
+  Patch by Yuli Barcohen, 05 Jun 2005
+
+* RPXlite configuration fixes
+  - Use correct flash sector size
+  - Use correct memory test end address
+  - Add support for bzip2 compression
+  - Various small fixes
+  Patch by Yuli Barcohen, 05 Jun 2005
+
+* Memory configuration changes for ZPC.1900 board
+  - Fix SDRAM timing on both local bus and 60x bus
+  - Add support for second flash bank (SIMM)
+  - Change boot flash base
+  Patch by Yuli Barcohen, 05 Jun 2005
+
+* Add support for Adder boards with 16MB SDRAM;
+  add support for second FEC on Adder87x board.
+  Patch by Yuli Barcohen, 05 Jun 2005
+
+* Fix conditional for including ks8695eth driver
+  Patch by Greg Ungerer, 04 Jun 2005
+
+* Fix Makefile: include config.mk only after CROSS_COMPILE is defined
+  Patch by Friedrich Lobenstock, 02 Jun 2005
+
+* Fix comment in common/soft_i2c.c
+  Patches by Peter Korsgaard/Tolunay Orkun, 26 May 2005
+
+* Cleanup compiler warnings.
+  Patch by Greg Ungerer, 21 May 2005
+
+* Word alignment fixes for word aligned NS16550 UART
+  Patch by Jean-Paul Saman, 01 Mar 2005
+
+  Fixes bug with UART that only supports word aligned access: removed
+  "__attribute__ ((packed));" for "(CFG_NS16550_REG_SIZE == 4)" some
+  (broken!) versions of GCC generate byte accesses when encountering
+  the packed attribute regardless if the struct is already correctly
+  aligned for a platform. Peripherals that can only handle word
+  aligned access won't work properly when accessed with byte access.
+  The struct NS16550 is already word aligned for REG_SIZE = 4, so
+  there is no need to packed the struct in that case.
+
+* Fix behaviour if gatewayip is not set
+  Patch by Robin Gilks, 23 Dec 2004
+
+* Fix cleanup for netstart board.
+  Remove build results from repository
+
+* Some code cleanup for GCC 4.x
+
+* Fixes to support environment in NAND flash;
+  enable NAND flash based environment for delta board.
+
 * Add support for Intel Monahans CPU on Zylonite and Delta boards
   (This is Work in Progress!)
 

MAKEALL

@@ -25,9 +25,10 @@ LIST_5xx="	\
 #########################################################################
 
 LIST_5xxx="	\
-	cpci5200	icecube_5100	icecube_5200	EVAL5200	\
-	mcc200		o2dnt		pf5200		PM520		\
-	Total5100	Total5200	Total5200_Rev2	TQM5200_auto	\
+	cpci5200	EVAL5200	icecube_5100	icecube_5200	\
+	lite5200b	mcc200		o2dnt		pf5200		\
+	PM520		Total5100	Total5200	Total5200_Rev2	\
+	TQM5200_auto							\
 "
 
 #########################################################################
@@ -43,16 +44,16 @@ LIST_8xx="	\
 	CCM		IP860		NETPHONE	RPXlite_DW	\
 	cogent_mpc8xx	IVML24		NETTA		RRvision	\
 	ELPT860		IVML24_128	NETTA2		SM850		\
-	ESTEEM192E	IVML24_256	NETTA_ISDN	SPD823TS	\
-	ETX094		IVMS8		NETVIA		svm_sc8xx	\
-	FADS823		IVMS8_128	NETVIA_V2	SXNI855T	\
-	FADS850SAR	IVMS8_256	NX823		TOP860		\
-	FADS860T	KUP4K		pcu_e		TQM823L		\
-	FLAGADM		KUP4X		QS823		TQM823L_LCD	\
-	FPS850L		LANTEC		QS850		TQM850L		\
-	GEN860T		lwmon		QS860T		TQM855L		\
-	GEN860T_SC	MBX		quantum		TQM860L		\
-							uc100		\
+	EP88x		IVML24_256	NETTA_ISDN	SPD823TS	\
+	ESTEEM192E	IVMS8		NETVIA		svm_sc8xx	\
+	ETX094		IVMS8_128	NETVIA_V2	SXNI855T	\
+	FADS823		IVMS8_256	NX823		TOP860		\
+	FADS850SAR	KUP4K		pcu_e		TQM823L		\
+	FADS860T	KUP4X		QS823		TQM823L_LCD	\
+	FLAGADM		LANTEC		QS850		TQM850L		\
+	FPS850L		lwmon		QS860T		TQM855L		\
+	GEN860T		MBX		quantum		TQM860L		\
+	GEN860T_SC					uc100		\
 							v37		\
 "
 
@@ -116,7 +117,7 @@ LIST_8260="	\
 #########################################################################
 
 LIST_83xx="	\
-	MPC8349ADS	TQM834x\
+	MPC8349ADS	TQM834x		MPC8349EMDS			\
 "
 
 

Makefile

@@ -53,9 +53,6 @@ ifeq (include/config.mk,$(wildcard include/config.mk))
 # load ARCH, BOARD, and CPU configuration
 include include/config.mk
 export	ARCH CPU BOARD VENDOR SOC
-# load other configuration
-include $(TOPDIR)/config.mk
-
 ifndef CROSS_COMPILE
 ifeq ($(HOSTARCH),ppc)
 CROSS_COMPILE =
@@ -88,11 +85,18 @@ endif
 ifeq ($(ARCH),microblaze)
 CROSS_COMPILE = mb-
 endif
+ifeq ($(ARCH),blackfin)
+CROSS_COMPILE = bfin-elf-
+endif
 endif
 endif
 
 export	CROSS_COMPILE
 
+# load other configuration
+include $(TOPDIR)/config.mk
+
+
 #########################################################################
 # U-Boot objects....order is important (i.e. start must be first)
 
@@ -110,6 +114,10 @@ endif
 ifeq ($(CPU),mpc85xx)
 OBJS += cpu/$(CPU)/resetvec.o
 endif
+ifeq ($(CPU),bf533)
+OBJS += cpu/$(CPU)/start1.o	cpu/$(CPU)/interrupt.o	cpu/$(CPU)/cache.o
+OBJS += cpu/$(CPU)/cplbhdlr.o	cpu/$(CPU)/cplbmgr.o	cpu/$(CPU)/flush.o
+endif
 
 LIBS  = lib_generic/libgeneric.a
 LIBS += board/$(BOARDDIR)/lib$(BOARD).a
@@ -295,6 +303,20 @@ icecube_5100_config:			unconfig
 inka4x0_config:	unconfig
 	@./mkconfig inka4x0 ppc mpc5xxx inka4x0
 
+lite5200b_config	\
+lite5200b_LOWBOOT_config:	unconfig
+	@ >include/config.h
+	@ echo "#define CONFIG_MPC5200_DDR"	>>include/config.h
+	@ echo "... DDR memory revision"
+	@ echo "#define CONFIG_MPC5200"		>>include/config.h
+	@ echo "#define CONFIG_LITE5200B"	>>include/config.h
+	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
+		{ echo "TEXT_BASE = 0xFF000000" >board/icecube/config.tmp ; \
+		  echo "... with LOWBOOT configuration" ; \
+		}
+	@ echo "... with MPC5200B processor"
+	@./mkconfig -a IceCube  ppc mpc5xxx icecube
+
 mcc200_config	\
 mcc200_lowboot_config:	unconfig
 	@ >include/config.h
@@ -433,6 +455,9 @@ cogent_mpc8xx_config:	unconfig
 ELPT860_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx elpt860 LEOX
 
+EP88x_config:		unconfig
+	@./mkconfig $(@:_config=) ppc mpc8xx ep88x
+
 ESTEEM192E_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx esteem192e
 
@@ -1282,6 +1307,9 @@ MPC8349ADS_config:	unconfig
 TQM834x_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc83xx tqm834x
 
+MPC8349EMDS_config:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc83xx mpc8349emds
+
 #########################################################################
 ## MPC85xx Systems
 #########################################################################
@@ -1503,7 +1531,7 @@ omap1510inn_config :	unconfig
 	@./mkconfig $(@:_config=) arm arm925t omap1510inn
 
 omap5912osk_config :	unconfig
-	@./mkconfig $(@:_config=) arm arm926ejs omap5912osk
+	@./mkconfig $(@:_config=) arm arm926ejs omap5912osk NULL omap
 
 omap1610inn_config \
 omap1610inn_cs0boot_config \
@@ -1523,7 +1551,7 @@ omap1610h2_cs_autoboot_config:	unconfig
 		echo "#define CONFIG_CS3_BOOT" >> ./include/config.h ; \
 		echo "... configured for CS3 boot"; \
 	fi;
-	@./mkconfig -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn
+	@./mkconfig -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn NULL omap
 
 omap730p2_config \
 omap730p2_cs0boot_config \
@@ -1535,7 +1563,7 @@ omap730p2_cs3boot_config :	unconfig
 		echo "#define CONFIG_CS3_BOOT" >> ./include/config.h ; \
 		echo "... configured for CS3 boot"; \
 	fi;
-	@./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2
+	@./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 NULL omap
 
 scb9328_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t scb9328 NULL imx
@@ -1858,6 +1886,19 @@ suzaku_config:	unconfig
 	@echo "#define CONFIG_SUZAKU 1" >> include/config.h
 	@./mkconfig -a $(@:_config=) microblaze microblaze suzaku AtmarkTechno
 
+#########################################################################
+## Blackfin
+#########################################################################
+ezkit533_config	:	unconfig
+	@./mkconfig $(@:_config=) blackfin bf533 ezkit533
+
+stamp_config	:	unconfig
+	@./mkconfig $(@:_config=) blackfin bf533 stamp
+
+dspstamp_config	:	unconfig
+	@./mkconfig $(@:_config=) blackfin bf533 dsp_stamp
+
+#########################################################################
 #########################################################################
 #########################################################################
 
@@ -1869,6 +1910,7 @@ clean:
 	rm -f examples/hello_world examples/timer \
 	      examples/eepro100_eeprom examples/sched \
 	      examples/mem_to_mem_idma2intr examples/82559_eeprom \
+	      examples/smc91111_eeprom \
 	      examples/test_burst
 	rm -f tools/img2srec tools/mkimage tools/envcrc tools/gen_eth_addr
 	rm -f tools/mpc86x_clk tools/ncb
@@ -1876,6 +1918,8 @@ clean:
 	rm -f tools/gdb/astest tools/gdb/gdbcont tools/gdb/gdbsend
 	rm -f tools/env/fw_printenv tools/env/fw_setenv
 	rm -f board/cray/L1/bootscript.c board/cray/L1/bootscript.image
+	rm -f board/netstar/eeprom board/netstar/crcek
+	rm -f board/netstar/*.srec board/netstar/*.bin
 	rm -f board/trab/trab_fkt board/voiceblue/eeprom
 	rm -f board/integratorap/u-boot.lds board/integratorcp/u-boot.lds
 

README

@@ -262,44 +262,44 @@ The following options need to be configured:
 		PowerPC based boards:
 		---------------------
 
-		CONFIG_ADCIOP		CONFIG_GEN860T		CONFIG_PCIPPC2
-		CONFIG_ADS860		CONFIG_GENIETV		CONFIG_PCIPPC6
-		CONFIG_AMX860		CONFIG_GTH		CONFIG_pcu_e
-		CONFIG_AP1000		CONFIG_gw8260		CONFIG_PIP405
-		CONFIG_AR405		CONFIG_hermes		CONFIG_PM826
-		CONFIG_BAB7xx		CONFIG_hymod		CONFIG_ppmc8260
-		CONFIG_c2mon		CONFIG_IAD210		CONFIG_QS823
-		CONFIG_CANBT		CONFIG_ICU862		CONFIG_QS850
-		CONFIG_CCM		CONFIG_IP860		CONFIG_QS860T
-		CONFIG_CMI		CONFIG_IPHASE4539	CONFIG_RBC823
-		CONFIG_cogent_mpc8260	CONFIG_IVML24		CONFIG_RPXClassic
-		CONFIG_cogent_mpc8xx	CONFIG_IVML24_128	CONFIG_RPXlite
-		CONFIG_CPCI405		CONFIG_IVML24_256	CONFIG_RPXsuper
-		CONFIG_CPCI4052		CONFIG_IVMS8		CONFIG_rsdproto
-		CONFIG_CPCIISER4	CONFIG_IVMS8_128	CONFIG_sacsng
-		CONFIG_CPU86		CONFIG_IVMS8_256	CONFIG_Sandpoint8240
-		CONFIG_CRAYL1		CONFIG_JSE		CONFIG_Sandpoint8245
-		CONFIG_CSB272		CONFIG_LANTEC		CONFIG_sbc8260
-		CONFIG_CU824		CONFIG_lwmon		CONFIG_sbc8560
-		CONFIG_DASA_SIM		CONFIG_MBX		CONFIG_SM850
-		CONFIG_DB64360		CONFIG_MBX860T		CONFIG_SPD823TS
-		CONFIG_DB64460		CONFIG_MHPC		CONFIG_STXGP3
-		CONFIG_DU405		CONFIG_MIP405		CONFIG_SXNI855T
-		CONFIG_DUET_ADS		CONFIG_MOUSSE		CONFIG_TQM823L
-		CONFIG_EBONY		CONFIG_MPC8260ADS	CONFIG_TQM8260
-		CONFIG_ELPPC		CONFIG_MPC8540ADS	CONFIG_TQM850L
-		CONFIG_ELPT860		CONFIG_MPC8540EVAL	CONFIG_TQM855L
-		CONFIG_ep8260		CONFIG_MPC8560ADS	CONFIG_TQM860L
-		CONFIG_ERIC		CONFIG_MUSENKI		CONFIG_TTTech
-		CONFIG_ESTEEM192E	CONFIG_MVS1		CONFIG_UTX8245
-		CONFIG_ETX094		CONFIG_NETPHONE		CONFIG_V37
-		CONFIG_EVB64260		CONFIG_NETTA		CONFIG_W7OLMC
-		CONFIG_FADS823		CONFIG_NETVIA		CONFIG_W7OLMG
-		CONFIG_FADS850SAR	CONFIG_NX823		CONFIG_WALNUT
-		CONFIG_FADS860T		CONFIG_OCRTC		CONFIG_ZPC1900
-		CONFIG_FLAGADM		CONFIG_ORSG		CONFIG_ZUMA
-		CONFIG_FPS850L		CONFIG_OXC
-		CONFIG_FPS860L		CONFIG_PCI405
+		CONFIG_ADCIOP		CONFIG_GEN860T		CONFIG_PCI405
+		CONFIG_ADS860		CONFIG_GENIETV		CONFIG_PCIPPC2
+		CONFIG_AMX860		CONFIG_GTH		CONFIG_PCIPPC6
+		CONFIG_AP1000		CONFIG_gw8260		CONFIG_pcu_e
+		CONFIG_AR405		CONFIG_hermes		CONFIG_PIP405
+		CONFIG_BAB7xx		CONFIG_hymod		CONFIG_PM826
+		CONFIG_c2mon		CONFIG_IAD210		CONFIG_ppmc8260
+		CONFIG_CANBT		CONFIG_ICU862		CONFIG_QS823
+		CONFIG_CCM		CONFIG_IP860		CONFIG_QS850
+		CONFIG_CMI		CONFIG_IPHASE4539	CONFIG_QS860T
+		CONFIG_cogent_mpc8260	CONFIG_IVML24		CONFIG_RBC823
+		CONFIG_cogent_mpc8xx	CONFIG_IVML24_128	CONFIG_RPXClassic
+		CONFIG_CPCI405		CONFIG_IVML24_256	CONFIG_RPXlite
+		CONFIG_CPCI4052		CONFIG_IVMS8		CONFIG_RPXsuper
+		CONFIG_CPCIISER4	CONFIG_IVMS8_128	CONFIG_rsdproto
+		CONFIG_CPU86		CONFIG_IVMS8_256	CONFIG_sacsng
+		CONFIG_CRAYL1		CONFIG_JSE		CONFIG_Sandpoint8240
+		CONFIG_CSB272		CONFIG_LANTEC		CONFIG_Sandpoint8245
+		CONFIG_CU824		CONFIG_LITE5200B	CONFIG_sbc8260
+		CONFIG_DASA_SIM		CONFIG_lwmon		CONFIG_sbc8560
+		CONFIG_DB64360		CONFIG_MBX		CONFIG_SM850
+		CONFIG_DB64460		CONFIG_MBX860T		CONFIG_SPD823TS
+		CONFIG_DU405		CONFIG_MHPC		CONFIG_STXGP3
+		CONFIG_DUET_ADS		CONFIG_MIP405		CONFIG_SXNI855T
+		CONFIG_EBONY		CONFIG_MOUSSE		CONFIG_TQM823L
+		CONFIG_ELPPC		CONFIG_MPC8260ADS	CONFIG_TQM8260
+		CONFIG_ELPT860		CONFIG_MPC8540ADS	CONFIG_TQM850L
+		CONFIG_ep8260		CONFIG_MPC8540EVAL	CONFIG_TQM855L
+		CONFIG_ERIC		CONFIG_MPC8560ADS	CONFIG_TQM860L
+		CONFIG_ESTEEM192E	CONFIG_MUSENKI		CONFIG_TTTech
+		CONFIG_ETX094		CONFIG_MVS1		CONFIG_UTX8245
+		CONFIG_EVB64260		CONFIG_NETPHONE		CONFIG_V37
+		CONFIG_FADS823		CONFIG_NETTA		CONFIG_W7OLMC
+		CONFIG_FADS850SAR	CONFIG_NETVIA		CONFIG_W7OLMG
+		CONFIG_FADS860T		CONFIG_NX823		CONFIG_WALNUT
+		CONFIG_FLAGADM		CONFIG_OCRTC		CONFIG_ZPC1900
+		CONFIG_FPS850L		CONFIG_ORSG		CONFIG_ZUMA
+		CONFIG_FPS860L		CONFIG_OXC
 
 		ARM based boards:
 		-----------------
@@ -426,7 +426,24 @@ The following options need to be configured:
 		The maximum size of the constructed OF tree.
 
 		OF_CPU - The proper name of the cpus node.
+		OF_SOC - The proper name of the soc node.
 		OF_TBCLK - The timebase frequency.
+		OF_STDOUT_PATH - The path to the console device
+
+		CONFIG_OF_HAS_BD_T
+
+		The resulting flat device tree will have a copy of the bd_t.
+		Space should be pre-allocated in the dts for the bd_t.
+
+		CONFIG_OF_HAS_UBOOT_ENV
+
+		The resulting flat device tree will have a copy of u-boot's
+		environment variables
+
+		CONFIG_OF_BOARD_SETUP
+
+		Board code has addition modification that it wants to make
+		to the flat device tree before handing it off to the kernel
 
 - Serial Ports:
 		CFG_PL010_SERIAL
@@ -621,7 +638,7 @@ The following options need to be configured:
 		CFG_CMD_DIAG	* Diagnostics
 		CFG_CMD_DOC	* Disk-On-Chip Support
 		CFG_CMD_DTT	* Digital Therm and Thermostat
-		CFG_CMD_ECHO	* echo arguments
+		CFG_CMD_ECHO	  echo arguments
 		CFG_CMD_EEPROM	* EEPROM read/write support
 		CFG_CMD_ELF	* bootelf, bootvx
 		CFG_CMD_ENV	  saveenv
@@ -1732,6 +1749,12 @@ Configuration Settings:
 - CFG_MALLOC_LEN:
 		Size of DRAM reserved for malloc() use.
 
+- CFG_BOOTM_LEN:
+		Normally compressed uImages are limited to an
+		uncompressed size of 8 MBytes. If this is not enough,
+		you can define CFG_BOOTM_LEN in your board config file
+		to adjust this setting to your needs.
+
 - CFG_BOOTMAPSZ:
 		Maximum size of memory mapped by the startup code of
 		the Linux kernel; all data that must be processed by

blackfin_config.mk

@@ -0,0 +1,24 @@
+#
+# (C) Copyright 2000-2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+PLATFORM_CPPFLAGS += -DCONFIG_BLACKFIN -D__blackfin__

board/adder/adder.c

@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2004 Arabella Software Ltd.
+ * Copyright (C) 2004-2005 Arabella Software Ltd.
  * Yuli Barcohen <yuli@arabellasw.com>
  *
  * Support for Analogue&Micro Adder boards family.
@@ -28,7 +28,8 @@
 #include <mpc8xx.h>
 
 /*
- * SDRAM is single Samsung K4S643232F-T70 chip.
+ * SDRAM is single Samsung K4S643232F-T70   chip (8MB)
+ *       or single Micron  MT48LC4M32B2TG-7 chip (16MB).
  * Minimal CPU frequency is 40MHz.
  */
 static uint sdram_table[] = {
@@ -53,7 +54,7 @@ static uint sdram_table[] = {
 	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
 
 	/* Refresh	(offset 0x30 in UPM RAM) */
-	0x1ff5fca4, 0xfffffc04, 0xfffffc04, 0xfffffc04,
+	0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
 	0xfffffc84, 0xfffffc07, 0xfffffc04, 0xfffffc04,
 	0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04,
 
@@ -63,7 +64,7 @@ static uint sdram_table[] = {
 
 long int initdram (int board_type)
 {
-	long int msize = CFG_SDRAM_SIZE;
+	long int msize;
 	volatile immap_t     *immap  = (volatile immap_t *)CFG_IMMR;
 	volatile memctl8xx_t *memctl = &immap->im_memctl;
 
@@ -72,11 +73,11 @@ long int initdram (int board_type)
 	/* Configure SDRAM refresh */
 	memctl->memc_mptpr = MPTPR_PTP_DIV32; /* BRGCLK/32 */
 
-	memctl->memc_mamr = (94 << 24) | CFG_MAMR;
-	memctl->memc_mar  = 0x0;
+	memctl->memc_mamr = (94 << 24) | CFG_MAMR; /* No refresh */
 	udelay(200);
 
 	/* Run precharge from location 0x15 */
+	memctl->memc_mar = 0x0;
 	memctl->memc_mcr = 0x80002115;
 	udelay(200);
 
@@ -84,13 +85,18 @@ long int initdram (int board_type)
 	memctl->memc_mcr = 0x80002830;
 	udelay(200);
 
-	memctl->memc_mar = 0x88;
-	udelay(200);
-
 	/* Run MRS pattern from location 0x16 */
+	memctl->memc_mar = 0x88;
 	memctl->memc_mcr = 0x80002116;
 	udelay(200);
 
+	memctl->memc_mamr |=  MAMR_PTAE; /* Enable refresh */
+	memctl->memc_or1   = ~(CFG_SDRAM_MAX_SIZE - 1) | OR_CSNT_SAM;
+	memctl->memc_br1   =  CFG_SDRAM_BASE | BR_PS_32 | BR_MS_UPMA | BR_V;
+
+	msize = get_ram_size(CFG_SDRAM_BASE, CFG_SDRAM_MAX_SIZE);
+	memctl->memc_or1  |= ~(msize - 1);
+
 	return msize;
 }
 

board/at91rm9200dk/at45.c

@@ -593,7 +593,7 @@ int AT91F_DataFlashRead(
 		if (AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY) != DATAFLASH_OK)
 			return -1;
 
-		if (AT91F_DataFlashContinuousRead (pDataFlash, addr, buffer, SizeToRead) != DATAFLASH_OK)
+		if (AT91F_DataFlashContinuousRead (pDataFlash, addr, (uchar *)buffer, SizeToRead) != DATAFLASH_OK)
 			return -1;
 
 		size -= SizeToRead;

board/at91rm9200dk/flash.c

@@ -393,8 +393,7 @@ outahere:
  * Copy memory to flash
  */
 
-volatile static int write_word (flash_info_t * info, ulong dest,
-								ulong data)
+static int write_word (flash_info_t * info, ulong dest, ulong data)
 {
 	volatile u16 *addr = (volatile u16 *) dest;
 	ulong result;
@@ -409,7 +408,6 @@ volatile static int write_word (flash_info_t * info, ulong dest,
 	if ((result & data) != data)
 		return ERR_NOT_ERASED;
 
-
 	/*
 	 * Disable interrupts which might cause a timeout
 	 * here. Remember that our exception vectors are

board/cmc_pu2/load_sernum_ethaddr.c

@@ -69,8 +69,8 @@ int i2c_read (unsigned char chip, unsigned int addr, int alen,
 void load_sernum_ethaddr (void)
 {
 	struct manufacturer_data data;
-	unsigned char  serial [9];
-	unsigned char  ethaddr[18];
+	char  ethaddr[18];
+	char  serial [9];
 	unsigned short chksum;
 	unsigned char *p;
 	unsigned short i, is, id;

board/cobra5272/flash.c

@@ -256,8 +256,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 	return rc;
 }
 
-
-volatile static int write_word (flash_info_t * info, ulong dest, ulong data)
+static int write_word (flash_info_t * info, ulong dest, ulong data)
 {
 	volatile u16 *addr = (volatile u16 *) dest;
 	ulong result;

board/delta/nand.c

@@ -229,7 +229,7 @@ static void wait_us(unsigned long us)
 	}
 }
 
-static void dfc_clear_nddb()
+static void dfc_clear_nddb(void)
 {
 	NDCR &= ~NDCR_ND_RUN;
 	wait_us(CFG_NAND_OTHER_TO);
@@ -263,7 +263,7 @@ static unsigned long dfc_wait_event(unsigned long event)
 }
 
 /* we don't always wan't to do this */
-static void dfc_new_cmd()
+static void dfc_new_cmd(void)
 {
 	int retry = 0;
 	unsigned long status;
@@ -393,7 +393,7 @@ static void dfc_cmdfunc(struct mtd_info *mtd, unsigned command,
 	return;
 }
 
-static void dfc_gpio_init()
+static void dfc_gpio_init(void)
 {
 	DFC_DEBUG2("Setting up DFC GPIO's.\n");
 

board/ep88x/Makefile

@@ -0,0 +1,46 @@
+#
+# Copyright (C) 2004 Arabella Software Ltd.
+# Yuli Barcohen <yuli@arabellasw.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/ep88x/config.mk

@@ -0,0 +1,27 @@
+#
+# Copyright (C) 2005 Arabella Software Ltd.
+# Yuli Barcohen <yuli@arabellasw.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Embedded Planet EP88x boards
+#
+TEXT_BASE = 0xFC000000

board/ep88x/ep88x.c

@@ -0,0 +1,133 @@
+/*
+ * Copyright (C) 2005 Arabella Software Ltd.
+ * Yuli Barcohen <yuli@arabellasw.com>
+ *
+ * Support for Embedded Planet EP88x boards.
+ * Tested on EP88xC with MPC885 CPU, 64MB SDRAM and 16MB flash.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+
+/*
+ * SDRAM uses two Micron chips.
+ * Minimal CPU frequency is 40MHz.
+ */
+static uint sdram_table[] = {
+	/* Single read	(offset 0x00 in UPM RAM) */
+	0xEFCBCC04, 0x0F37C804, 0x0EEEC004, 0x01B98404,
+	0x1FF74C00, 0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05,
+
+	/* Burst read	(offset 0x08 in UPM RAM) */
+	0xEFCBCC04, 0x0F37C804, 0x0EEEC004, 0x00BDC404,
+	0x00FFCC00, 0x00FFCC00, 0x01FB8C00, 0x1FF74C00,
+	0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05,
+	0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05,
+
+	/* Single write (offset 0x18 in UPM RAM) */
+	0xEFCBCC04, 0x0F37C804, 0x0EEE8002, 0x01B90404,
+	0x1FF74C05, 0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05,
+
+	/* Burst write	(offset 0x20 in UPM RAM) */
+	0xEFCBCC04, 0x0F37C804, 0x0EEE8000, 0x00BD4400,
+	0x00FFCC00, 0x00FFCC02, 0x01FB8C04, 0x1FF74C05,
+	0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05,
+	0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05, 0xFFFFCC05,
+
+	/* Refresh	(offset 0x30 in UPM RAM) */
+	0xEFFACC04, 0x0FF5CC04, 0x0FFFCC04, 0x1FFFCC04,
+	0xFFFFCC05, 0xFFFFCC05, 0xEFFB8C34, 0x0FF74C34,
+	0x0FFACCB4, 0x0FF5CC34, 0x0FFFC034, 0x0FFFC0B4,
+
+	/* Exception	(offset 0x3C in UPM RAM) */
+	0x0FEA8034, 0x1FB54034,	0xFFFFCC34, 0xFFFFCC05
+};
+
+int board_early_init_f (void)
+{
+	vu_char *bcsr = (vu_char *)CFG_BCSR;
+
+	bcsr[0] |= 0x0C; /* Turn the LEDs off */
+	bcsr[2] |= 0x08; /* Enable flash WE# line - necessary for
+			    flash detection by CFI driver
+			 */
+
+#if defined(CONFIG_8xx_CONS_SMC1)
+	bcsr[6] |= 0x10; /* Enables RS-232 transceiver */
+#endif
+#if defined(CONFIG_8xx_CONS_SCC2)
+	bcsr[7] |= 0x10; /* Enables RS-232 transceiver */
+#endif
+#ifdef CONFIG_ETHER_ON_FEC1
+	bcsr[8] |= 0xC0; /* Enable Ethernet 1 PHY */
+#endif
+#ifdef CONFIG_ETHER_ON_FEC2
+	bcsr[8] |= 0x30; /* Enable Ethernet 2 PHY */
+#endif
+
+	return 0;
+}
+
+long int initdram (int board_type)
+{
+	long int msize;
+	volatile immap_t     *immap  = (volatile immap_t *)CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+	upmconfig(UPMA, sdram_table, sizeof(sdram_table) / sizeof(uint));
+
+	/* Configure SDRAM refresh */
+	memctl->memc_mptpr = MPTPR_PTP_DIV2; /* BRGCLK/2 */
+
+	memctl->memc_mamr = (65 << 24) | CFG_MAMR; /* No refresh */
+	udelay(100);
+
+	/* Run MRS pattern from location 0x36 */
+	memctl->memc_mar = 0x88;
+	memctl->memc_mcr = 0x80002236;
+	udelay(100);
+
+	memctl->memc_mamr |=  MAMR_PTAE; /* Enable refresh */
+	memctl->memc_or1   = ~(CFG_SDRAM_MAX_SIZE - 1) | OR_CSNT_SAM;
+	memctl->memc_br1   =  CFG_SDRAM_BASE | BR_PS_32 | BR_MS_UPMA | BR_V;
+
+	msize = get_ram_size(CFG_SDRAM_BASE, CFG_SDRAM_MAX_SIZE);
+	memctl->memc_or1  |= ~(msize - 1);
+
+	return msize;
+}
+
+int checkboard( void )
+{
+	vu_char *bcsr = (vu_char *)CFG_BCSR;
+
+	puts("Board: ");
+	switch (bcsr[15]) {
+	case 0xE7:
+		puts("EP88xC 1.0");
+		break;
+	default:
+		printf("unknown ID=%02X", bcsr[15]);
+	}
+	printf("  CPLD revision %d\n", bcsr[14]);
+
+	return 0;
+}

board/ep88x/u-boot.lds

@@ -0,0 +1,122 @@
+/*
+ * (C) Copyright 2001-2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Modified by Yuli Barcohen <yuli@arabellasw.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp        : { *(.interp)		}
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt           : { *(.plt)		}
+  .text          :
+  {
+    cpu/mpc8xx/start.o	(.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
+ENTRY(_start)

board/ezkit533/Makefile

@@ -0,0 +1,44 @@
+#
+# U-boot - Makefile
+#
+# Copyright (c) 2005 blackfin.uclinux.org
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o ezkit533.o
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/ezkit533/config.mk

@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x01FC0000
+PLATFORM_CPPFLAGS += -I$(TOPDIR)

board/ezkit533/ezkit533.c

@@ -0,0 +1,71 @@
+/*
+ * U-boot - ezkit533.c
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#if defined(CONFIG_MISC_INIT_R)
+#include "psd4256.h"
+#endif
+
+int checkboard(void)
+{
+	printf("CPU:   ADSP BF533 Rev.: 0.%d\n", *pCHIPID >> 28);
+	printf("Board: ADI BF533 EZ-Kit Lite board\n");
+	printf("       Support: http://blackfin.uclinux.org/\n");
+	printf("       Richard Klingler <richard@uclinux.net>\n");
+	return 0;
+}
+
+long int initdram(int board_type)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+#ifdef DEBUG
+	int brate;
+	char *tmp = getenv("baudrate");
+	brate = simple_strtoul(tmp, NULL, 16);
+	printf("Serial Port initialized with Baud rate = %x\n",brate);
+	printf("SDRAM attributes:\n");
+	printf("tRCD %d SCLK Cycles,tRP %d SCLK Cycles,tRAS %d SCLK Cycles"
+	       "tWR %d SCLK Cycles,CAS Latency %d SCLK cycles \n",
+	       3, 3, 6, 2, 3);
+	printf("SDRAM Begin: 0x%x\n", CFG_SDRAM_BASE);
+	printf("Bank size = %d MB\n", CFG_MAX_RAM_SIZE >> 20);
+#endif
+	gd->bd->bi_memstart = CFG_SDRAM_BASE;
+	gd->bd->bi_memsize = CFG_MAX_RAM_SIZE;
+	return CFG_MAX_RAM_SIZE;
+}
+
+#if defined(CONFIG_MISC_INIT_R)
+/* miscellaneous platform dependent initialisations */
+int misc_init_r(void)
+{
+	/* Set direction bits for Video en/decoder reset as output	*/
+	*(volatile unsigned char *)(CFG_FLASH1_BASE + PSD_PORTA_DIR) = PSDA_VDEC_RST | PSDA_VENC_RST;
+	/* Deactivate Video en/decoder reset lines			*/
+	*(volatile unsigned char *)(CFG_FLASH1_BASE + PSD_PORTA_DOUT) = PSDA_VDEC_RST | PSDA_VENC_RST;
+}
+#endif

board/ezkit533/flash-defines.h

@@ -0,0 +1,130 @@
+/*
+ * U-boot - flash-defines.h
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __FLASHDEFINES_H__
+#define __FLASHDEFINES_H__
+
+#include <common.h>
+
+#define V_ULONG(a)		(*(volatile unsigned long *)( a ))
+#define V_BYTE(a)		(*(volatile unsigned char *)( a ))
+#define TRUE			0x1
+#define FALSE			0x0
+#define BUFFER_SIZE		0x80000
+#define NO_COMMAND		0
+#define GET_CODES		1
+#define RESET			2
+#define WRITE			3
+#define FILL			4
+#define ERASE_ALL		5
+#define ERASE_SECT		6
+#define READ			7
+#define GET_SECTNUM		8
+#define FLASH_START_L 		0x0000
+#define FLASH_START_H 		0x2000
+#define FLASH_TOT_SECT		40
+#define FLASH_SIZE 		0x220000
+#define FLASH_MAN_ST 		2
+#define CFG_FLASH0_BASE		0x20000000
+#define RESET_VAL		0xF0
+
+
+asm("#define FLASH_START_L 0x0000");
+asm("#define FLASH_START_H 0x2000");
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+int get_codes(void);
+int poll_toggle_bit(long lOffset);
+void reset_flash(void);
+int erase_flash(void);
+int erase_block_flash(int,unsigned long);
+void unlock_flash(long lOffset);
+int write_data(long lStart, long lCount, long lStride, int *pnData);
+int FillData(long lStart, long lCount, long lStride, int *pnData);
+int read_data(long lStart, long lCount, long lStride, int *pnData);
+int read_flash(long nOffset, int *pnValue);
+int write_flash(long nOffset, int nValue);
+void get_sector_number(long lOffset, int *pnSector);
+int GetSectorProtectionStatus(flash_info_t * info, int nSector);
+int GetOffset(int nBlock);
+int AFP_NumSectors = 40;
+long AFP_SectorSize1 = 0x10000;
+int AFP_SectorSize2 = 0x4000;
+
+#define WRITESEQ1		0x0AAA
+#define WRITESEQ2		0x0554
+#define WRITESEQ3		0x0AAA
+#define WRITESEQ4		0x0AAA
+#define WRITESEQ5		0x0554
+#define WRITESEQ6		0x0AAA
+#define WRITEDATA1		0xaa
+#define WRITEDATA2		0x55
+#define WRITEDATA3		0x80
+#define WRITEDATA4		0xaa
+#define WRITEDATA5		0x55
+#define WRITEDATA6		0x10
+#define PriFlashABegin		0
+#define SecFlashABegin		32
+#define SecFlashBBegin		36
+#define PriFlashAOff		0x0
+#define PriFlashBOff		0x100000
+#define SecFlashAOff		0x200000
+#define SecFlashBOff		0x280000
+#define INVALIDLOCNSTART	0x20270000
+#define INVALIDLOCNEND		0x20280000
+#define BlockEraseVal		0x30
+#define UNLOCKDATA1		0xaa
+#define UNLOCKDATA2		0x55
+#define UNLOCKDATA3		0xa0
+#define GETCODEDATA1		0xaa
+#define GETCODEDATA2		0x55
+#define GETCODEDATA3		0x90
+#define SecFlashASec1Off	0x200000
+#define SecFlashASec2Off	0x204000
+#define SecFlashASec3Off	0x206000
+#define SecFlashASec4Off	0x208000
+#define SecFlashAEndOff		0x210000
+#define SecFlashBSec1Off	0x280000
+#define SecFlashBSec2Off	0x284000
+#define SecFlashBSec3Off	0x286000
+#define SecFlashBSec4Off	0x288000
+#define SecFlashBEndOff		0x290000
+
+#define SECT32			32
+#define SECT33			33
+#define SECT34			34
+#define SECT35			35
+#define SECT36			36
+#define SECT37			37
+#define SECT38			38
+#define SECT39			39
+
+#define FLASH_SUCCESS	0
+#define FLASH_FAIL	-1
+
+#endif

board/ezkit533/flash.c

@@ -0,0 +1,476 @@
+/*
+ * U-boot - flash.c Flash driver for PSD4256GV
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ * This file is based on BF533EzFlash.c originally written by Analog Devices, Inc.
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include "flash-defines.h"
+
+void flash_reset(void)
+{
+	reset_flash();
+}
+
+unsigned long flash_get_size(ulong baseaddr, flash_info_t * info,
+			     int bank_flag)
+{
+	int id = 0, i = 0;
+	static int FlagDev = 1;
+
+	id = get_codes();
+	if(FlagDev)	{
+#ifdef DEBUG
+		printf("Device ID of the Flash is %x\n", id);
+#endif
+		FlagDev = 0;
+	}
+	info->flash_id = id;
+
+	switch (bank_flag) {
+	case 0:
+		for (i = PriFlashABegin; i < SecFlashABegin; i++)
+			info->start[i] = (baseaddr + (i * AFP_SectorSize1));
+		info->size = 0x200000;
+		info->sector_count = 32;
+		break;
+	case 1:
+		info->start[0] = baseaddr + SecFlashASec1Off;
+		info->start[1] = baseaddr + SecFlashASec2Off;
+		info->start[2] = baseaddr + SecFlashASec3Off;
+		info->start[3] = baseaddr + SecFlashASec4Off;
+		info->size = 0x10000;
+		info->sector_count = 4;
+		break;
+	case 2:
+		info->start[0] = baseaddr + SecFlashBSec1Off;
+		info->start[1] = baseaddr + SecFlashBSec2Off;
+		info->start[2] = baseaddr + SecFlashBSec3Off;
+		info->start[3] = baseaddr + SecFlashBSec4Off;
+		info->size = 0x10000;
+		info->sector_count = 4;
+		break;
+	}
+	return (info->size);
+}
+
+unsigned long flash_init(void)
+{
+	unsigned long size_b0, size_b1, size_b2;
+	int i;
+
+	size_b0 = size_b1 = size_b2 = 0;
+#ifdef DEBUG
+	printf("Flash Memory Start 0x%x\n", CFG_FLASH_BASE);
+	printf("Memory Map for the Flash\n");
+	printf("0x20000000 - 0x200FFFFF Flash A Primary (1MB)\n");
+	printf("0x20100000 - 0x201FFFFF Flash B Primary (1MB)\n");
+	printf("0x20200000 - 0x2020FFFF Flash A Secondary (64KB)\n");
+	printf("0x20280000 - 0x2028FFFF Flash B Secondary (64KB)\n");
+	printf("Please type command flinfo for information on Sectors \n");
+#endif
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	size_b0 = flash_get_size(CFG_FLASH0_BASE, &flash_info[0], 0);
+	size_b1 = flash_get_size(CFG_FLASH0_BASE, &flash_info[1], 1);
+	size_b2 = flash_get_size(CFG_FLASH0_BASE, &flash_info[2], 2);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN || size_b0 == 0) {
+		printf("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0 >> 20);
+	}
+
+	(void)flash_protect(FLAG_PROTECT_SET,CFG_FLASH0_BASE,(flash_info[0].start[2] - 1),&flash_info[0]);
+
+	return (size_b0 + size_b1 + size_b2);
+}
+
+void flash_print_info(flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id) {
+	case FLASH_PSD4256GV:
+		printf("ST Microelectronics ");
+		break;
+	default:
+		printf("Unknown Vendor ");
+		break;
+	}
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf("\n   ");
+		printf(" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "     ");
+	}
+	printf("\n");
+	return;
+}
+
+int flash_erase(flash_info_t * info, int s_first, int s_last)
+{
+	int cnt = 0,i;
+	int prot,sect;
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect])
+			prot++;
+	}
+
+	if (prot)
+		printf ("- Warning: %d protected sectors will not be erased!\n", prot);
+	else
+		printf ("\n");
+
+	cnt = s_last - s_first + 1;
+
+	if (cnt == FLASH_TOT_SECT) {
+		printf("Erasing flash, Please Wait \n");
+		if(erase_flash() < 0) {
+			printf("Erasing flash failed \n");
+			return FLASH_FAIL;
+		}
+	} else {
+		printf("Erasing Flash locations, Please Wait\n");
+		for (i = s_first; i <= s_last; i++) {
+			if (info->protect[i] == 0) {	/* not protected */
+				if(erase_block_flash(i, info->start[i]) < 0) {
+					printf("Error Sector erasing \n");
+					return FLASH_FAIL;
+				}
+			}
+		}
+	}
+	return FLASH_SUCCESS;
+}
+
+int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	int ret;
+
+	ret = write_data(addr, cnt, 1, (int *) src);
+	if(ret == FLASH_FAIL)
+		return ERR_NOT_ERASED;
+	return FLASH_SUCCESS;
+}
+
+
+int write_data(long lStart, long lCount, long lStride, int *pnData)
+{
+	long i = 0;
+	int j = 0;
+	unsigned long ulOffset = lStart - CFG_FLASH_BASE;
+	int d;
+	int iShift = 0;
+	int iNumWords = 2;
+	int nLeftover = lCount % 4;
+	int nSector = 0;
+
+	for (i = 0; (i < lCount / 4) && (i < BUFFER_SIZE); i++) {
+		for (iShift = 0, j = 0; (j < iNumWords);
+			j++, ulOffset += (lStride * 2)) {
+			if ((ulOffset >= INVALIDLOCNSTART)
+			&& (ulOffset < INVALIDLOCNEND)) {
+				printf("Invalid locations, Try writing to another location \n");
+				return FLASH_FAIL;
+			}
+			get_sector_number(ulOffset, &nSector);
+			read_flash(ulOffset,&d);
+			if(d != 0xffff) {
+				printf("Flash not erased at offset 0x%x Please erase to reprogram \n",ulOffset);
+				return FLASH_FAIL;
+			}
+			unlock_flash(ulOffset);
+			if(write_flash(ulOffset, (pnData[i] >> iShift)) < 0) {
+				printf("Error programming the flash \n");
+				return FLASH_FAIL;
+			}
+			iShift += 16;
+		}
+	}
+	if (nLeftover > 0) {
+		if ((ulOffset >= INVALIDLOCNSTART)
+			&& (ulOffset < INVALIDLOCNEND))
+				return FLASH_FAIL;
+		get_sector_number(ulOffset, &nSector);
+		read_flash(ulOffset,&d);
+		if(d != 0xffff) {
+			printf("Flash already programmed. Please erase to reprogram \n");
+			printf("uloffset = 0x%x \t d = 0x%x\n",ulOffset,d);
+			return FLASH_FAIL;
+		}
+		unlock_flash(ulOffset);
+		if(write_flash(ulOffset, pnData[i]) < 0) {
+			printf("Error programming the flash \n");
+			return FLASH_FAIL;
+		}
+	}
+	return FLASH_SUCCESS;
+}
+
+int read_data(long ulStart, long lCount, long lStride, int *pnData)
+{
+	long i = 0;
+	int j = 0;
+	long ulOffset = ulStart;
+	int iShift = 0;
+	int iNumWords = 2;
+	int nLeftover = lCount % 4;
+	int nHi, nLow;
+	int nSector = 0;
+
+	for (i = 0; (i < lCount / 4) && (i < BUFFER_SIZE); i++) {
+		for (iShift = 0, j = 0; j < iNumWords; j += 2) {
+			if ((ulOffset >= INVALIDLOCNSTART)
+				&& (ulOffset < INVALIDLOCNEND))
+					return FLASH_FAIL;
+
+			get_sector_number(ulOffset, &nSector);
+			read_flash(ulOffset, &nLow);
+			ulOffset += (lStride * 2);
+			read_flash(ulOffset, &nHi);
+			ulOffset += (lStride * 2);
+			pnData[i] = (nHi << 16) | nLow;
+		}
+	}
+	if (nLeftover > 0) {
+		if ((ulOffset >= INVALIDLOCNSTART)
+			&& (ulOffset < INVALIDLOCNEND))
+				return FLASH_FAIL;
+
+		get_sector_number(ulOffset, &nSector);
+		read_flash(ulOffset, &pnData[i]);
+	}
+	return FLASH_SUCCESS;
+}
+
+int write_flash(long nOffset, int nValue)
+{
+	long addr;
+
+	addr = (CFG_FLASH_BASE + nOffset);
+	asm("ssync;");
+	*(unsigned volatile short *) addr = nValue;
+	asm("ssync;");
+	if(poll_toggle_bit(nOffset) < 0)
+		return FLASH_FAIL;
+	return FLASH_SUCCESS;
+}
+
+int read_flash(long nOffset, int *pnValue)
+{
+	int nValue = 0x0;
+	long addr = (CFG_FLASH_BASE + nOffset);
+
+	if (nOffset != 0x2)
+		reset_flash();
+	asm("ssync;");
+	nValue = *(volatile unsigned short *) addr;
+	asm("ssync;");
+	*pnValue = nValue;
+	return TRUE;
+}
+
+int poll_toggle_bit(long lOffset)
+{
+	unsigned int u1,u2;
+	unsigned long timeout = 0xFFFFFFFF;
+	volatile unsigned long *FB = (volatile unsigned long *)(0x20000000 + lOffset);
+	while(1) {
+		if(timeout < 0)
+			break;
+		u1 = *(volatile unsigned short *)FB;
+		u2 = *(volatile unsigned short *)FB;
+		if((u1 & 0x0040) == (u2 & 0x0040))
+			return FLASH_SUCCESS;
+		if((u2 & 0x0020) == 0x0000)
+			continue;
+		u1 = *(volatile unsigned short *)FB;
+		if((u2 & 0x0040) == (u1 & 0x0040))
+			return FLASH_SUCCESS;
+		else {
+			reset_flash();
+			return FLASH_FAIL;
+		}
+		timeout--;
+	}
+	printf("Time out occured \n");
+	if(timeout <0)	return FLASH_FAIL;
+}
+
+void reset_flash(void)
+{
+	write_flash(WRITESEQ1, RESET_VAL);
+	/* Wait for 10 micro seconds */
+	udelay(10);
+}
+
+int erase_flash(void)
+{
+	write_flash(WRITESEQ1, WRITEDATA1);
+	write_flash(WRITESEQ2, WRITEDATA2);
+	write_flash(WRITESEQ3, WRITEDATA3);
+	write_flash(WRITESEQ4, WRITEDATA4);
+	write_flash(WRITESEQ5, WRITEDATA5);
+	write_flash(WRITESEQ6, WRITEDATA6);
+
+	if(poll_toggle_bit(0x0000) < 0)
+		return FLASH_FAIL;
+
+	write_flash(SecFlashAOff + WRITESEQ1, WRITEDATA1);
+	write_flash(SecFlashAOff + WRITESEQ2, WRITEDATA2);
+	write_flash(SecFlashAOff + WRITESEQ3, WRITEDATA3);
+	write_flash(SecFlashAOff + WRITESEQ4, WRITEDATA4);
+	write_flash(SecFlashAOff + WRITESEQ5, WRITEDATA5);
+	write_flash(SecFlashAOff + WRITESEQ6, WRITEDATA6);
+
+	if(poll_toggle_bit(SecFlashASec1Off) < 0)
+		return FLASH_FAIL;
+
+	write_flash(PriFlashBOff + WRITESEQ1, WRITEDATA1);
+	write_flash(PriFlashBOff + WRITESEQ2, WRITEDATA2);
+	write_flash(PriFlashBOff + WRITESEQ3, WRITEDATA3);
+	write_flash(PriFlashBOff + WRITESEQ4, WRITEDATA4);
+	write_flash(PriFlashBOff + WRITESEQ5, WRITEDATA5);
+	write_flash(PriFlashBOff + WRITESEQ6, WRITEDATA6);
+
+	if(poll_toggle_bit(PriFlashBOff) <0)
+		return FLASH_FAIL;
+
+	write_flash(SecFlashBOff + WRITESEQ1, WRITEDATA1);
+	write_flash(SecFlashBOff + WRITESEQ2, WRITEDATA2);
+	write_flash(SecFlashBOff + WRITESEQ3, WRITEDATA3);
+	write_flash(SecFlashBOff + WRITESEQ4, WRITEDATA4);
+	write_flash(SecFlashBOff + WRITESEQ5, WRITEDATA5);
+	write_flash(SecFlashBOff + WRITESEQ6, WRITEDATA6);
+
+	if(poll_toggle_bit(SecFlashBOff) < 0)
+		return FLASH_FAIL;
+
+	return FLASH_SUCCESS;
+}
+
+int erase_block_flash(int nBlock, unsigned long address)
+{
+	long ulSectorOff = 0x0;
+
+	if ((nBlock < 0) || (nBlock > AFP_NumSectors))
+		return FALSE;
+
+	ulSectorOff = (address - CFG_FLASH_BASE);
+
+	write_flash((WRITESEQ1 | ulSectorOff), WRITEDATA1);
+	write_flash((WRITESEQ2 | ulSectorOff), WRITEDATA2);
+	write_flash((WRITESEQ3 | ulSectorOff), WRITEDATA3);
+	write_flash((WRITESEQ4 | ulSectorOff), WRITEDATA4);
+	write_flash((WRITESEQ5 | ulSectorOff), WRITEDATA5);
+
+	write_flash(ulSectorOff, BlockEraseVal);
+
+	if(poll_toggle_bit(ulSectorOff) < 0)
+		return FLASH_FAIL;
+
+	return FLASH_SUCCESS;
+}
+
+void unlock_flash(long ulOffset)
+{
+	unsigned long ulOffsetAddr = ulOffset;
+	ulOffsetAddr &= 0xFFFF0000;
+
+	write_flash((WRITESEQ1 | ulOffsetAddr), UNLOCKDATA1);
+	write_flash((WRITESEQ2 | ulOffsetAddr), UNLOCKDATA2);
+	write_flash((WRITESEQ3 | ulOffsetAddr), UNLOCKDATA3);
+}
+
+int get_codes()
+{
+	int dev_id = 0;
+
+	write_flash(WRITESEQ1, GETCODEDATA1);
+	write_flash(WRITESEQ2, GETCODEDATA2);
+	write_flash(WRITESEQ3, GETCODEDATA3);
+
+	read_flash(0x0002, &dev_id);
+	dev_id &= 0x00FF;
+
+	reset_flash();
+
+	return dev_id;
+}
+
+void get_sector_number(long ulOffset, int *pnSector)
+{
+	int nSector = 0;
+
+	if (ulOffset >= SecFlashAOff) {
+		if ((ulOffset < SecFlashASec1Off)
+			&& (ulOffset < SecFlashASec2Off)) {
+				nSector = SECT32;
+		} else if ((ulOffset >= SecFlashASec2Off)
+			&& (ulOffset < SecFlashASec3Off)) {
+				nSector = SECT33;
+		} else if ((ulOffset >= SecFlashASec3Off)
+			&& (ulOffset < SecFlashASec4Off)) {
+				nSector = SECT34;
+		} else if ((ulOffset >= SecFlashASec4Off)
+			&& (ulOffset < SecFlashAEndOff)) {
+				nSector = SECT35;
+		}
+	} else if (ulOffset >= SecFlashBOff) {
+		if ((ulOffset < SecFlashBSec1Off)
+			&& (ulOffset < SecFlashBSec2Off)) {
+				nSector = SECT36;
+		}
+		if ((ulOffset < SecFlashBSec2Off)
+			&& (ulOffset < SecFlashBSec3Off)) {
+				nSector = SECT37;
+		}
+		if ((ulOffset < SecFlashBSec3Off)
+			&& (ulOffset < SecFlashBSec4Off)) {
+				nSector = SECT38;
+		}
+		if ((ulOffset < SecFlashBSec4Off)
+			&& (ulOffset < SecFlashBEndOff)) {
+				nSector = SECT39;
+		}
+	} else if ((ulOffset >= PriFlashAOff) && (ulOffset < SecFlashAOff)) {
+		nSector = ulOffset & 0xffff0000;
+		nSector = ulOffset >> 16;
+		nSector = nSector & 0x000ff;
+	}
+
+	if ((nSector >= 0) && (nSector < AFP_NumSectors)) {
+		*pnSector = nSector;
+	}
+}

board/ezkit533/psd4256.h

@@ -0,0 +1,67 @@
+/*
+ * U-boot - psd4256.h
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Flash A/B Port A configuration registers.
+ * Addresses are offset values to CFG_FLASH1_BASE
+ * for Flash A and CFG_FLASH2_BASE for Flash B.
+ */
+
+#define	PSD_PORTA_DIN	0x070000
+#define	PSD_PORTA_DOUT	0x070004
+#define	PSD_PORTA_DIR	0x070006
+
+/*
+ * Flash A/B Port B configuration registers
+ * Addresses are offset values to CFG_FLASH1_BASE
+ * for Flash A and CFG_FLASH2_BASE for Flash B.
+ */
+
+#define	PSD_PORTB_DIN	0x070001
+#define	PSD_PORTB_DOUT	0x070005
+#define	PSD_PORTB_DIR	0x070007
+
+/*
+ * Flash A Port A Bit definitions
+ */
+
+#define	PSDA_PPICLK1	0x20		/* PPI Clock select bit 1		*/
+#define	PSDA_PPICLK0	0x10		/* PPI Clock select bit 0		*/
+#define	PSDA_VDEC_RST	0x08		/* Video decoder reset, 0 = RESET	*/
+#define	PSDA_VENC_RST	0x04		/* Video encoder reset, 0 = RESET	*/
+#define	PSDA_CODEC_RST	0x01		/* Codec reset, 0 = RESET		*/
+
+/*
+ * Flash A Port B Bit definitions
+ */
+
+#define	PSDA_LED9	0x20		/* LED 9, 1 = LED ON			*/
+#define	PSDA_LED8	0x10		/* LED 8, 1 = LED ON			*/
+#define	PSDA_LED7	0x08		/* LED 7, 1 = LED ON			*/
+#define	PSDA_LED6	0x04		/* LED 6, 1 = LED ON			*/
+#define	PSDA_LED5	0x02		/* LED 5, 1 = LED ON			*/
+#define	PSDA_LED4	0x01		/* LED 4, 1 = LED ON			*/

board/ezkit533/u-boot.lds

@@ -0,0 +1,148 @@
+/*
+ * U-boot - u-boot.lds
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(bfin)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector before the environment sector. If it throws 	*/
+    /* an error during compilation remove an object here to get	*/
+    /* it linked after the configuration sector.		*/
+
+    cpu/bf533/start.o		(.text)
+    cpu/bf533/start1.o		(.text)
+    cpu/bf533/traps.o		(.text)
+    cpu/bf533/interrupt.o	(.text)
+    cpu/bf533/serial.o		(.text)
+    common/dlmalloc.o		(.text)
+    lib_generic/vsprintf.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_generic/zlib.o		(.text)
+    board/ezkit533/ezkit533.o		(.text)
+
+    . = DEFINED(env_offset) ? env_offset : .;
+    common/environment.o	(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/fads/fads.c

@@ -726,24 +726,23 @@ static void checkdboard(void)
 
 int checkboard (void)
 {
-	/* get revision from BCSR 3 */
+#if   defined(CONFIG_MPC86xADS)
+	puts ("Board: MPC86xADS\n");
+#elif defined(CONFIG_MPC885ADS)
+	puts ("Board: MPC885ADS\n");
+#else /* Only old ADS/FADS have got revision ID in BCSR3 */
 	uint r =  (((*((uint *) BCSR3) >> 23) & 1) << 3)
 		| (((*((uint *) BCSR3) >> 19) & 1) << 2)
 		| (((*((uint *) BCSR3) >> 16) & 3));
 
 	puts ("Board: ");
-
-#if defined(CONFIG_MPC86xADS)
-	puts ("MPC86xADS");
-#elif defined(CONFIG_MPC885ADS)
-	puts ("MPC885ADS");
-	r = 0; /* I've got NR (No Revision) board */
-#elif defined(CONFIG_FADS)
+#if defined(CONFIG_FADS)
 	puts ("FADS");
 	checkdboard ();
 #else
 	puts ("ADS");
 #endif
+
 	puts (" rev ");
 
 	switch (r) {
@@ -758,13 +757,9 @@ int checkboard (void)
 		puts ("A - warning, read errata \n");
 		break;
 	case 0x03:
-		puts ("B \n");
+		puts ("B\n");
 		break;
-#elif defined(CONFIG_MPC885ADS)
-	case 0x00:
-		puts ("NR\n");
-		break;
-#else  /* FADS and newer */
+#else  /* FADS */
 	case 0x00:
 		puts ("ENG\n");
 		break;
@@ -776,6 +771,7 @@ int checkboard (void)
 		printf ("unknown (0x%x)\n", r);
 		return -1;
 	}
+#endif /* CONFIG_MPC86xADS */
 
 	return 0;
 }
@@ -848,7 +844,7 @@ int pcmcia_init(void)
 	switch ((pcmp->pcmc_pipr >> 14) & 3)
 #endif
 	{
-	case 0x00 :
+	case 0x03 :
 		printf("5V");
 		v = 5;
 		break;
@@ -860,7 +856,7 @@ int pcmcia_init(void)
 		v = 5;
 #endif
 		break;
-	case 0x03 :
+	case 0x00 :
 		printf("5V, 3V and x.xV");
 #ifdef CONFIG_FADS
 		v = 3; /* User lower voltage if supported! */

board/fads/fads.h

@@ -55,18 +55,26 @@
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 #endif
 
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_NFSBOOTCOMMAND							\
     "dhcp;"									\
-    "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "		\
-    "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"	\
+    "setenv bootargs root=/dev/nfs rw nfsroot=$rootpath "			\
+    "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;"		\
     "bootm"
 
+#define CONFIG_BOOTCOMMAND							\
+    "setenv bootargs root=/dev/mtdblock2 rw mtdparts=phys:1280K(ROM)ro,-(root) "\
+    "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;"		\
+    "bootm fe080000"
+
+#undef CONFIG_BOOTARGS
+
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 #define CONFIG_BZIP2	 /* include support for bzip2 compressed images */
 
 /*
- * New MPC86xADS and Duet provide two Ethernet connectivity options:
+ * New MPC86xADS and MPC885ADS provide two Ethernet connectivity options:
  * 10Mbit/s on SCC and 100Mbit/s on FEC. FADS provides SCC Ethernet on
  * motherboard and FEC Ethernet on daughterboard. All new PQ1 chips have
  * got FEC so FEC is the default.
@@ -89,7 +97,9 @@
 
 #ifndef CONFIG_COMMANDS
 #define CONFIG_COMMANDS	(CONFIG_CMD_DFL   \
+			 | CFG_CMD_ASKENV \
 			 | CFG_CMD_DHCP   \
+			 | CFG_CMD_ECHO   \
 			 | CFG_CMD_IMMAP  \
 			 | CFG_CMD_JFFS2  \
 			 | CFG_CMD_MII    \
@@ -104,16 +114,18 @@
 /*
  * Miscellaneous configurable options
  */
-#undef	CFG_LONGHELP			/* undef to save memory		*/
-#define	CFG_PROMPT		"=>"	/* Monitor Command Prompt	*/
+#define	CFG_PROMPT		"=>"		/* Monitor Command Prompt	*/
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+#define	CFG_LONGHELP				/* #undef to save memory	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
 #endif
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define	CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size	*/
+#define	CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_LOAD_ADDR	 	0x00100000
 
@@ -126,6 +138,7 @@
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
+
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
@@ -148,6 +161,14 @@
 #define	CFG_SDRAM_BASE		0x00000000
 #if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC885ADS) /* New ADS or Duet */
 #define	CFG_SDRAM_SIZE		0x00800000      	/* 8 Mbyte */
+/*
+ * 2048	SDRAM rows
+ * 1000	factor s -> ms
+ * 64	PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4	Number of refresh cycles per period
+ * 64	Refresh cycle in ms per number of rows
+ */
+#define CFG_PTA_PER_CLK		((2048 * 64 * 1000) / (4 * 64))
 #elif defined(CONFIG_FADS)				/* Old/new FADS */
 #define	CFG_SDRAM_SIZE		0x00400000		/* 4 Mbyte */
 #else							/* Old ADS */
@@ -223,9 +244,7 @@
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
 
 /*-----------------------------------------------------------------------
  * I2C configuration
@@ -277,31 +296,21 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#define CFG_SCCR	(SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
+#define CFG_SCCR	SCCR_TBS
 
 /*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		14-22
+ * DER - Debug Enable Register
  *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control
- */
-#ifndef CFG_PLPRCR
-#define CFG_PLPRCR	PLPRCR_TEXPS
-#endif
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
+ * Set to zero to prevent the processor from entering debug mode
  */
 #define CFG_DER		 0
 
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
+/* Because of the way the 860 starts up and assigns CS0 the entire
+ * address space, we have to set the memory controller differently.
+ * Normally, you write the option register first, and then enable the
+ * chip select by writing the base register.  For CS0, you must write
+ * the base register first, followed by the option register.
+ */
 
 /*
  * Init Memory Controller:
@@ -335,9 +344,6 @@
 
 /* values according to the manual */
 
-#define PCMCIA_MEM_ADDR		((uint)0xFF020000)
-#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
-
 #define	BCSR0			((uint) (BCSR_ADDR + 0x00))
 #define	BCSR1			((uint) (BCSR_ADDR + 0x04))
 #define	BCSR2			((uint) (BCSR_ADDR + 0x08))
@@ -396,59 +402,28 @@
 #define BCSR4_TFPLDL             ((uint)0x40000000)
 #define BCSR4_TPSQEL             ((uint)0x20000000)
 #define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#define BCSR4_FETHCFG0           ((uint)0x04000000)
-#define BCSR4_FETHFDE            ((uint)0x02000000)
-#define BCSR4_FETHCFG1           ((uint)0x00400000)
-#define BCSR4_FETHRST            ((uint)0x00200000)
-
-#ifdef CONFIG_MPC823
+#if defined(CONFIG_MPC823)
 #define BCSR4_USB_EN             ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
 #define BCSR4_USB_SPEED          ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0           ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
 #define BCSR4_VCCO               ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE            ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
 #define BCSR4_VIDEO_ON           ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
 #define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1           ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
 #define BCSR4_VIDEO_RST          ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST            ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
 #define BCSR4_MODEM_EN           ((uint)0x00100000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
 #define BCSR4_DATA_VOICE         ((uint)0x00080000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC850
+#elif defined(CONFIG_MPC850)
 #define BCSR4_DATA_VOICE         ((uint)0x00080000)
-#endif /* CONFIG_MPC850 */
+#elif defined(CONFIG_MPC860SAR)
+#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
+#else /* MPC860T and other chips with FEC */
+#define BCSR4_FETH_EN            ((uint)0x08000000)
+#define BCSR4_FETHCFG0           ((uint)0x04000000)
+#define BCSR4_FETHFDE            ((uint)0x02000000)
+#define BCSR4_FETHCFG1           ((uint)0x00400000)
+#define BCSR4_FETHRST            ((uint)0x00200000)
+#endif
 
-/* BSCR5 exists on MPC86xADS and Duet ADS only */
+/* BSCR5 exists on MPC86xADS and MPC885ADS only */
 
 #define CFG_PHYDEV_ADDR		(BCSR_ADDR + 0x20000)
 
@@ -511,4 +486,4 @@
 #define CFG_ATA_ALT_OFFSET	0x0000
 
 #define CONFIG_DISK_SPINUP_TIME 1000000
-#undef CONFIG_DISK_SPINUP_TIME	/* usin´ Compact Flash */
+/* #undef CONFIG_DISK_SPINUP_TIME */	/* usin  Compact Flash */

board/icecube/flash.c

@@ -23,6 +23,7 @@
 
 #include <common.h>
 
+#ifndef CFG_FLASH_CFI_DRIVER
 flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
 
 /* NOTE - CONFIG_FLASH_16BIT means the CPU interface is 16-bit, it
@@ -489,3 +490,4 @@ static int write_word_amd (flash_info_t *info, FPWV *dest, FPW data)
 
 	return (res);
 }
+#endif /*CFG_FLASH_CFI_DRIVER*/

board/icecube/icecube.c

@@ -28,12 +28,15 @@
 #include <mpc5xxx.h>
 #include <pci.h>
 
-#if defined(CONFIG_MPC5200_DDR)
-#include "mt46v16m16-75.h"
+#if defined(CONFIG_LITE5200B)
+#include "mt46v32m16.h"
 #else
+# if defined(CONFIG_MPC5200_DDR)
+#  include "mt46v16m16-75.h"
+# else
 #include "mt48lc16m16a2-75.h"
+# endif
 #endif
-
 #ifndef CFG_RAMBOOT
 static void sdram_start (int hi_addr)
 {
@@ -236,7 +239,9 @@ long int initdram (int board_type)
 
 int checkboard (void)
 {
-#if defined(CONFIG_MPC5200)
+#if defined (CONFIG_LITE5200B)
+	puts ("Board: Freescale Lite5200B\n");
+#elif defined(CONFIG_MPC5200)
 	puts ("Board: Motorola MPC5200 (IceCube)\n");
 #elif defined(CONFIG_MGT5100)
 	puts ("Board: Motorola MGT5100 (IceCube)\n");

board/icecube/mt46v32m16.h

@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR	1		/* is DDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE	0x018D0000
+#define SDRAM_EMODE	0x40090000
+#define SDRAM_CONTROL	0x704f0f00
+#define SDRAM_CONFIG1	0x73722930
+#define SDRAM_CONFIG2	0x47770000
+#define SDRAM_TAPDELAY	0x10000000
+
+#else
+#error CONFIG_MPC5200 not defined
+#endif

board/lart/flash.c

@@ -348,7 +348,7 @@ outahere:
  * Copy memory to flash
  */
 
-volatile static int write_word (flash_info_t *info, ulong dest, ulong data)
+static int write_word (flash_info_t *info, ulong dest, ulong data)
 {
     vu_long *addr = (vu_long *)dest;
     ulong result;

board/lpd7a40x/flash.c

@@ -351,8 +351,7 @@ outahere:
  * Copy memory to flash
  */
 
-volatile static int write_word (flash_info_t * info, ulong dest,
-								ulong data)
+static int write_word (flash_info_t * info, ulong dest, ulong data)
 {
 	vu_long *addr = (vu_long *) dest;
 	ulong result;

board/m5272c3/flash.c

@@ -256,8 +256,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 	return rc;
 }
 
-
-volatile static int write_word (flash_info_t * info, ulong dest, ulong data)
+static int write_word (flash_info_t * info, ulong dest, ulong data)
 {
 	volatile u16 *addr = (volatile u16 *) dest;
 	ulong result;

board/m5282evb/flash.c

@@ -256,8 +256,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 	return rc;
 }
 
-
-volatile static int write_word (flash_info_t * info, ulong dest, ulong data)
+static int write_word (flash_info_t * info, ulong dest, ulong data)
 {
 	volatile u16 *addr = (volatile u16 *) dest;
 	ulong result;

board/mpc8349ads/Makefile

@@ -24,7 +24,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	:= $(BOARD).o
+OBJS	:= $(BOARD).o pci.o
 
 $(LIB):	$(OBJS) $(SOBJS)
 	$(AR) crv $@ $(OBJS)

board/mpc8349ads/mpc8349ads.c

@@ -147,47 +147,6 @@ int checkboard (void)
 	return 0;
 }
 
-#if defined(CONFIG_PCI)
-/*
- * Initialize PCI Devices, report devices found
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc83xxads_config_table[] = {
-	{PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,
-	pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
-				    PCI_ENET0_MEMADDR,
-				    PCI_COMMON_MEMORY | PCI_COMMAND_MASTER
-	} },
-	{}
-}
-#endif
-
-
-volatile static struct pci_controller hose[] = {
-	{
-#ifndef CONFIG_PCI_PNP
-	config_table:pci_mpc83xxads_config_table,
-#endif
-	},
-	{
-#ifndef CONFIG_PCI_PNP
-	config_table:pci_mpc83xxads_config_table,
-#endif
-	}
-};
-#endif /* CONFIG_PCI */
-
-
-void
-pci_init_board(void)
-{
-#ifdef CONFIG_PCI
-	extern void pci_mpc83xx_init(volatile struct pci_controller *hose);
-
-	pci_mpc83xx_init(hose);
-#endif /* CONFIG_PCI */
-}
-
 /*
  * if MPC8349ADS is soldered with SDRAM
  */

board/mpc8349ads/pci.c

@@ -0,0 +1,380 @@
+/*
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <asm/mmu.h>
+#include <common.h>
+#include <asm/global_data.h>
+#include <pci.h>
+#include <asm/mpc8349_pci.h>
+#include <i2c.h>
+
+#ifdef CONFIG_PCI
+
+/* System RAM mapped to PCI space */
+#define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_PHYS	CFG_SDRAM_BASE
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc83xxads_config_table[] = {
+	{PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+	 PCI_IDSEL_NUMBER, PCI_ANY_ID,
+ 	 pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
+				     PCI_ENET0_MEMADDR,
+				     PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+		}
+	},
+	{}
+};
+#endif
+
+static struct pci_controller pci_hose[] = {
+       {
+#ifndef CONFIG_PCI_PNP
+       config_table:pci_mpc83xxads_config_table,
+#endif
+       },
+       {
+#ifndef CONFIG_PCI_PNP
+       config_table:pci_mpc83xxads_config_table,
+#endif
+       }
+};
+
+/**************************************************************************
+ *
+ * pib_init() -- initialize the PCA9555PW IO expander on the PIB board
+ *
+ */
+void
+pib_init(void)
+{
+	u8 val8;
+	/*
+	 * Assign PIB PMC slot to desired PCI bus
+	 */
+	mpc8349_i2c = (i2c_t*)(CFG_IMMRBAR + CFG_I2C2_OFFSET);
+	i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
+
+	val8 = 0;
+	i2c_write(0x23, 0x6, 1, &val8, 1);
+	i2c_write(0x23, 0x7, 1, &val8, 1);
+	val8 = 0xff;
+	i2c_write(0x23, 0x2, 1, &val8, 1);
+	i2c_write(0x23, 0x3, 1, &val8, 1);
+
+	val8 = 0;
+	i2c_write(0x26, 0x6, 1, &val8, 1);
+	val8 = 0x34;
+	i2c_write(0x26, 0x7, 1, &val8, 1);
+#if defined(PCI_64BIT)
+	val8 = 0xf4;	/* PMC2:PCI1/64-bit */
+#elif defined(PCI_ALL_PCI1)
+	val8 = 0xf3;	/* PMC1:PCI1 PMC2:PCI1 PMC3:PCI1 */
+#elif defined(PCI_ONE_PCI1)
+	val8 = 0xf9;	/* PMC1:PCI1 PMC2:PCI2 PMC3:PCI2 */
+#else
+	val8 = 0xf5;	/* PMC1:PCI1 PMC2:PCI1 PMC3:PCI2 */
+#endif
+	i2c_write(0x26, 0x2, 1, &val8, 1);
+	val8 = 0xff;
+	i2c_write(0x26, 0x3, 1, &val8, 1);
+	val8 = 0;
+	i2c_write(0x27, 0x6, 1, &val8, 1);
+	i2c_write(0x27, 0x7, 1, &val8, 1);
+	val8 = 0xff;
+	i2c_write(0x27, 0x2, 1, &val8, 1);
+	val8 = 0xef;
+	i2c_write(0x27, 0x3, 1, &val8, 1);
+	asm("eieio");
+
+#if defined(PCI_64BIT)
+	printf("PCI1: 64-bit on PMC2\n");
+#elif defined(PCI_ALL_PCI1)
+	printf("PCI1: 32-bit on PMC1, PMC2, PMC3\n");
+#elif defined(PCI_ONE_PCI1)
+	printf("PCI1: 32-bit on PMC1\n");
+	printf("PCI2: 32-bit on PMC2, PMC3\n");
+#else
+	printf("PCI1: 32-bit on PMC1, PMC2\n");
+	printf("PCI2: 32-bit on PMC3\n");
+#endif
+}
+
+/**************************************************************************
+ * pci_init_board()
+ *
+ * NOTICE: PCI2 is not currently supported
+ *
+ */
+void
+pci_init_board(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	volatile immap_t *	immr;
+	volatile clk8349_t *	clk;
+	volatile law8349_t *	pci_law;
+	volatile pot8349_t *	pci_pot;
+	volatile pcictrl8349_t *	pci_ctrl;
+	volatile pciconf8349_t *	pci_conf;
+	u16 reg16;
+	u32 reg32;
+	u32 dev;
+	struct	pci_controller * hose;
+
+	immr = (immap_t *)CFG_IMMRBAR;
+	clk = (clk8349_t *)&immr->clk;
+	pci_law = immr->sysconf.pcilaw;
+	pci_pot = immr->ios.pot;
+	pci_ctrl = immr->pci_ctrl;
+	pci_conf = immr->pci_conf;
+
+	hose = &pci_hose[0];
+
+	pib_init();
+
+	/*
+	 * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode
+	 */
+
+	reg32 = clk->occr;
+	udelay(2000);
+	clk->occr = 0xff000000;
+	udelay(2000);
+
+	/*
+	 * Release PCI RST Output signal
+	 */
+	pci_ctrl[0].gcr = 0;
+	udelay(2000);
+	pci_ctrl[0].gcr = 1;
+
+#ifdef CONFIG_MPC83XX_PCI2
+	pci_ctrl[1].gcr = 0;
+	udelay(2000);
+	pci_ctrl[1].gcr = 1;
+#endif
+
+	/* We need to wait at least a 1sec based on PCI specs */
+	{
+		int i;
+
+		for (i = 0; i < 1000; ++i)
+			udelay (1000);
+	}
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR;
+	pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
+
+	pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR;
+	pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_32M;
+
+	/*
+	 * Configure PCI Outbound Translation Windows
+	 */
+
+	/* PCI1 mem space - prefetch */
+	pci_pot[0].potar = (CFG_PCI1_MEM_BASE >> 12) & POTAR_TA_MASK;
+	pci_pot[0].pobar = (CFG_PCI1_MEM_PHYS >> 12) & POBAR_BA_MASK;
+	pci_pot[0].pocmr = POCMR_EN | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+	/* PCI1 IO space */
+	pci_pot[1].potar = (CFG_PCI1_IO_BASE >> 12) & POTAR_TA_MASK;
+	pci_pot[1].pobar = (CFG_PCI1_IO_PHYS >> 12) & POBAR_BA_MASK;
+	pci_pot[1].pocmr = POCMR_EN | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
+
+	/* PCI1 mmio - non-prefetch mem space */
+	pci_pot[2].potar = (CFG_PCI1_MMIO_BASE >> 12) & POTAR_TA_MASK;
+	pci_pot[2].pobar = (CFG_PCI1_MMIO_PHYS >> 12) & POBAR_BA_MASK;
+	pci_pot[2].pocmr = POCMR_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+	/*
+	 * Configure PCI Inbound Translation Windows
+	 */
+
+	/* we need RAM mapped to PCI space for the devices to
+	 * access main memory */
+	pci_ctrl[0].pitar1 = 0x0;
+	pci_ctrl[0].pibar1 = 0x0;
+	pci_ctrl[0].piebar1 = 0x0;
+	pci_ctrl[0].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
+
+	hose->first_busno = 0;
+	hose->last_busno = 0xff;
+
+	/* PCI memory prefetch space */
+	pci_set_region(hose->regions + 0,
+		       CFG_PCI1_MEM_BASE,
+		       CFG_PCI1_MEM_PHYS,
+		       CFG_PCI1_MEM_SIZE,
+		       PCI_REGION_MEM|PCI_REGION_PREFETCH);
+
+	/* PCI memory space */
+	pci_set_region(hose->regions + 1,
+		       CFG_PCI1_MMIO_BASE,
+		       CFG_PCI1_MMIO_PHYS,
+		       CFG_PCI1_MMIO_SIZE,
+		       PCI_REGION_MEM);
+
+	/* PCI IO space */
+	pci_set_region(hose->regions + 2,
+		       CFG_PCI1_IO_BASE,
+		       CFG_PCI1_IO_PHYS,
+		       CFG_PCI1_IO_SIZE,
+		       PCI_REGION_IO);
+
+	/* System memory space */
+	pci_set_region(hose->regions + 3,
+		       CONFIG_PCI_SYS_MEM_BUS,
+		       CONFIG_PCI_SYS_MEM_PHYS,
+		       gd->ram_size,
+		       PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+	hose->region_count = 4;
+
+	pci_setup_indirect(hose,
+			   (CFG_IMMRBAR+0x8300),
+			   (CFG_IMMRBAR+0x8304));
+
+	pci_register_hose(hose);
+
+	/*
+	 * Write to Command register
+	 */
+	reg16 = 0xff;
+	dev = PCI_BDF(hose->first_busno, 0, 0);
+	pci_hose_read_config_word (hose, dev, PCI_COMMAND, &reg16);
+	reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+	pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+	/*
+	 * Clear non-reserved bits in status register.
+	 */
+	pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+	pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+	pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+#ifdef CONFIG_PCI_SCAN_SHOW
+	printf("PCI:   Bus Dev VenId DevId Class Int\n");
+#endif
+	/*
+	 * Hose scan.
+	 */
+	hose->last_busno = pci_hose_scan(hose);
+
+#ifdef CONFIG_MPC83XX_PCI2
+	hose = &pci_hose[1];
+
+	/*
+	 * Configure PCI Outbound Translation Windows
+	 */
+
+	/* PCI2 mem space - prefetch */
+	pci_pot[3].potar = (CFG_PCI2_MEM_BASE >> 12) & POTAR_TA_MASK;
+	pci_pot[3].pobar = (CFG_PCI2_MEM_PHYS >> 12) & POBAR_BA_MASK;
+	pci_pot[3].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK);
+
+	/* PCI2 IO space */
+	pci_pot[4].potar = (CFG_PCI2_IO_BASE >> 12) & POTAR_TA_MASK;
+	pci_pot[4].pobar = (CFG_PCI2_IO_PHYS >> 12) & POBAR_BA_MASK;
+	pci_pot[4].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
+
+	/* PCI2 mmio - non-prefetch mem space */
+	pci_pot[5].potar = (CFG_PCI2_MMIO_BASE >> 12) & POTAR_TA_MASK;
+	pci_pot[5].pobar = (CFG_PCI2_MMIO_PHYS >> 12) & POBAR_BA_MASK;
+	pci_pot[5].pocmr = POCMR_EN | POCMR_PCI2 | (POCMR_CM_256M & POCMR_CM_MASK);
+
+	/*
+	 * Configure PCI Inbound Translation Windows
+	 */
+
+	/* we need RAM mapped to PCI space for the devices to
+	 * access main memory */
+	pci_ctrl[1].pitar1 = 0x0;
+	pci_ctrl[1].pibar1 = 0x0;
+	pci_ctrl[1].piebar1 = 0x0;
+	pci_ctrl[1].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
+
+	hose->first_busno = pci_hose[0].last_busno + 1;
+	hose->last_busno = 0xff;
+
+	/* PCI memory prefetch space */
+	pci_set_region(hose->regions + 0,
+		       CFG_PCI2_MEM_BASE,
+		       CFG_PCI2_MEM_PHYS,
+		       CFG_PCI2_MEM_SIZE,
+		       PCI_REGION_MEM|PCI_REGION_PREFETCH);
+
+	/* PCI memory space */
+	pci_set_region(hose->regions + 1,
+		       CFG_PCI2_MMIO_BASE,
+		       CFG_PCI2_MMIO_PHYS,
+		       CFG_PCI2_MMIO_SIZE,
+		       PCI_REGION_MEM);
+
+	/* PCI IO space */
+	pci_set_region(hose->regions + 2,
+		       CFG_PCI2_IO_BASE,
+		       CFG_PCI2_IO_PHYS,
+		       CFG_PCI2_IO_SIZE,
+		       PCI_REGION_IO);
+
+	/* System memory space */
+	pci_set_region(hose->regions + 3,
+		       CONFIG_PCI_SYS_MEM_BUS,
+		       CONFIG_PCI_SYS_MEM_PHYS,
+		       gd->ram_size,
+		       PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+	hose->region_count = 4;
+
+	pci_setup_indirect(hose,
+			   (CFG_IMMRBAR+0x8380),
+			   (CFG_IMMRBAR+0x8384));
+
+	pci_register_hose(hose);
+
+	/*
+	 * Write to Command register
+	 */
+	reg16 = 0xff;
+	dev = PCI_BDF(hose->first_busno, 0, 0);
+	pci_hose_read_config_word (hose, dev, PCI_COMMAND, &reg16);
+	reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+	pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+	/*
+	 * Clear non-reserved bits in status register.
+	 */
+	pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+	pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+	pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+	/*
+	 * Hose scan.
+	 */
+	hose->last_busno = pci_hose_scan(hose);
+#endif
+
+}
+#endif /* CONFIG_PCI */

board/mpc8349emds/Makefile

@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/mpc8349emds/config.mk

@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# MPC8349EMDS
+#
+
+TEXT_BASE  =   0xFE000000

board/mpc8349emds/mpc8349emds.c

@@ -0,0 +1,602 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ioports.h>
+#include <mpc83xx.h>
+#include <asm/mpc8349_pci.h>
+#include <i2c.h>
+#include <spd.h>
+#include <miiphy.h>
+#include <command.h>
+#if defined(CONFIG_PCI)
+#include <pci.h>
+#endif
+#if defined(CONFIG_SPD_EEPROM)
+#include <spd_sdram.h>
+#endif
+int fixed_sdram(void);
+void sdram_init(void);
+
+#if defined(CONFIG_DDR_ECC) && defined(CONFIG_MPC83XX)
+void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+int board_early_init_f (void)
+{
+	volatile u8* bcsr = (volatile u8*)CFG_BCSR;
+
+	/* Enable flash write */
+	bcsr[1] &= ~0x01;
+
+	return 0;
+}
+
+#define ns2clk(ns) (ns / (1000000000 / CONFIG_8349_CLKIN) + 1)
+
+long int initdram (int board_type)
+{
+	volatile immap_t *im = (immap_t *)CFG_IMMRBAR;
+	u32 msize = 0;
+
+	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	puts("Initializing\n");
+
+	/* DDR SDRAM - Main SODIMM */
+	im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR;
+#if defined(CONFIG_SPD_EEPROM)
+	msize = spd_sdram();
+#else
+	msize = fixed_sdram();
+#endif
+	/*
+	 * Initialize SDRAM if it is on local bus.
+	 */
+	sdram_init();
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(msize * 1024 * 1024);
+#endif
+	puts("   DDR RAM: ");
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return (msize * 1024 * 1024);
+}
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*************************************************************************
+ *  fixed sdram init -- doesn't use serial presence detect.
+ ************************************************************************/
+int fixed_sdram(void)
+{
+	volatile immap_t *im = (immap_t *)CFG_IMMRBAR;
+	u32 msize = 0;
+	u32 ddr_size;
+	u32 ddr_size_log2;
+
+	msize = CFG_DDR_SIZE;
+	for (ddr_size = msize << 20, ddr_size_log2 = 0;
+	     (ddr_size > 1);
+	     ddr_size = ddr_size>>1, ddr_size_log2++) {
+		if (ddr_size & 1) {
+			return -1;
+		}
+	}
+	im->sysconf.ddrlaw[0].bar = ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff);
+	im->sysconf.ddrlaw[0].ar = LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
+
+#if (CFG_DDR_SIZE != 256)
+#warning Currenly any ddr size other than 256 is not supported
+#endif
+	im->ddr.csbnds[2].csbnds = 0x0000000f;
+	im->ddr.cs_config[2] = CFG_DDR_CONFIG;
+
+	/* currently we use only one CS, so disable the other banks */ 
+	im->ddr.cs_config[0] = 0;
+	im->ddr.cs_config[1] = 0;
+	im->ddr.cs_config[3] = 0;
+
+	im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
+	im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
+	
+	im->ddr.sdram_cfg =
+		SDRAM_CFG_SREN
+#if defined(CONFIG_DDR_2T_TIMING)
+		| SDRAM_CFG_2T_EN
+#endif
+		| 2 << SDRAM_CFG_SDRAM_TYPE_SHIFT;
+#if defined (CONFIG_DDR_32BIT)
+	/* for 32-bit mode burst length is 8 */
+	im->ddr.sdram_cfg |= (SDRAM_CFG_32_BE | SDRAM_CFG_8_BE);
+#endif
+	im->ddr.sdram_mode = CFG_DDR_MODE;
+
+	im->ddr.sdram_interval = CFG_DDR_INTERVAL; 
+	udelay(200);
+
+	/* enable DDR controller */
+	im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+	return msize;
+}
+#endif/*!CFG_SPD_EEPROM*/
+
+
+int checkboard (void)
+{
+	puts("Board: Freescale MPC8349EMDS\n");
+	return 0;
+}
+
+#if defined(CONFIG_PCI)
+/*
+ * Initialize PCI Devices, report devices found
+ */
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc8349emds_config_table[] = {
+	{PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,PCI_ANY_ID,
+	pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
+				    PCI_ENET0_MEMADDR,
+				    PCI_COMMON_MEMORY | PCI_COMMAND_MASTER
+	} },
+	{}
+}
+#endif
+
+volatile static struct pci_controller hose[] = {
+	{
+#ifndef CONFIG_PCI_PNP
+	config_table:pci_mpc8349emds_config_table,
+#endif
+	},
+	{
+#ifndef CONFIG_PCI_PNP
+	config_table:pci_mpc8349emds_config_table,
+#endif
+	}
+};
+#endif /* CONFIG_PCI */
+
+void pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+	extern void pci_mpc83xx_init(volatile struct pci_controller *hose);
+
+	pci_mpc83xx_init(hose);
+#endif /* CONFIG_PCI */
+}
+
+/*
+ * if MPC8349EMDS is soldered with SDRAM
+ */
+#if defined(CFG_BR2_PRELIM)  \
+	&& defined(CFG_OR2_PRELIM) \
+	&& defined(CFG_LBLAWBAR2_PRELIM) \
+	&& defined(CFG_LBLAWAR2_PRELIM)
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+
+void sdram_init(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+	volatile lbus8349_t *lbc= &immap->lbus;
+	uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
+
+	puts("\n   SDRAM on Local Bus: ");
+	print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+	/*
+	 * Setup SDRAM Base and Option Registers, already done in cpu_init.c
+	 */
+
+	/* setup mtrpt, lsrt and lbcr for LB bus */
+	lbc->lbcr = CFG_LBC_LBCR;
+	lbc->mrtpr = CFG_LBC_MRTPR;
+	lbc->lsrt = CFG_LBC_LSRT;
+	asm("sync");
+
+	/*
+	 * Configure the SDRAM controller Machine Mode Register.
+	 */
+	lbc->lsdmr = CFG_LBC_LSDMR_5; /* 0x40636733; normal operation */
+
+	lbc->lsdmr = CFG_LBC_LSDMR_1; /* 0x68636733; precharge all the banks */
+	asm("sync");
+	*sdram_addr = 0xff;
+	udelay(100);
+
+	lbc->lsdmr = CFG_LBC_LSDMR_2; /* 0x48636733; auto refresh */
+	asm("sync");
+	/*1 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+	/*2 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+	/*3 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+	/*4 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+	/*5 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+	/*6 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+	/*7 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+	/*8 times*/
+	*sdram_addr = 0xff;
+	udelay(100);
+
+	/* 0x58636733; mode register write operation */
+	lbc->lsdmr = CFG_LBC_LSDMR_4;
+	asm("sync");
+	*sdram_addr = 0xff;
+	udelay(100);
+
+	lbc->lsdmr = CFG_LBC_LSDMR_5; /* 0x40636733; normal operation */
+	asm("sync");
+	*sdram_addr = 0xff;
+	udelay(100);
+}
+#else
+void sdram_init(void)
+{
+	put("SDRAM on Local Bus is NOT available!\n");
+}
+#endif
+
+#if defined(CONFIG_DDR_ECC) && defined(CONFIG_DDR_ECC_CMD)
+/*
+ * ECC user commands
+ */
+void ecc_print_status(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+	volatile ddr8349_t *ddr = &immap->ddr;
+
+	printf("\nECC mode: %s\n\n", (ddr->sdram_cfg & SDRAM_CFG_ECC_EN) ? "ON" : "OFF");
+
+	/* Interrupts */
+	printf("Memory Error Interrupt Enable:\n");
+	printf("  Multiple-Bit Error Interrupt Enable: %d\n",
+			(ddr->err_int_en & ECC_ERR_INT_EN_MBEE) ? 1 : 0);
+	printf("  Single-Bit Error Interrupt Enable: %d\n",
+			(ddr->err_int_en & ECC_ERR_INT_EN_SBEE) ? 1 : 0);
+	printf("  Memory Select Error Interrupt Enable: %d\n\n",
+			(ddr->err_int_en & ECC_ERR_INT_EN_MSEE) ? 1 : 0);
+
+	/* Error disable */
+	printf("Memory Error Disable:\n");
+	printf("  Multiple-Bit Error Disable: %d\n",
+			(ddr->err_disable & ECC_ERROR_DISABLE_MBED) ? 1 : 0);
+	printf("  Sinle-Bit Error Disable: %d\n",
+			(ddr->err_disable & ECC_ERROR_DISABLE_SBED) ? 1 : 0);
+	printf("  Memory Select Error Disable: %d\n\n",
+			(ddr->err_disable & ECC_ERROR_DISABLE_MSED) ? 1 : 0);
+
+	/* Error injection */
+	printf("Memory Data Path Error Injection Mask High/Low: %08lx %08lx\n",
+			ddr->data_err_inject_hi, ddr->data_err_inject_lo);
+
+	printf("Memory Data Path Error Injection Mask ECC:\n");
+	printf("  ECC Mirror Byte: %d\n",
+			(ddr->ecc_err_inject & ECC_ERR_INJECT_EMB) ? 1 : 0);
+	printf("  ECC Injection Enable: %d\n",
+			(ddr->ecc_err_inject & ECC_ERR_INJECT_EIEN) ? 1 : 0);
+	printf("  ECC Error Injection Mask: 0x%02x\n\n",
+			ddr->ecc_err_inject & ECC_ERR_INJECT_EEIM);
+
+	/* SBE counter/threshold */
+	printf("Memory Single-Bit Error Management (0..255):\n");
+	printf("  Single-Bit Error Threshold: %d\n",
+			(ddr->err_sbe & ECC_ERROR_MAN_SBET) >> ECC_ERROR_MAN_SBET_SHIFT);
+	printf("  Single-Bit Error Counter: %d\n\n",
+			(ddr->err_sbe & ECC_ERROR_MAN_SBEC) >> ECC_ERROR_MAN_SBEC_SHIFT);
+
+	/* Error detect */
+	printf("Memory Error Detect:\n");
+	printf("  Multiple Memory Errors: %d\n",
+			(ddr->err_detect & ECC_ERROR_DETECT_MME) ? 1 : 0);
+	printf("  Multiple-Bit Error: %d\n",
+			(ddr->err_detect & ECC_ERROR_DETECT_MBE) ? 1 : 0);
+	printf("  Single-Bit Error: %d\n",
+			(ddr->err_detect & ECC_ERROR_DETECT_SBE) ? 1 : 0);
+	printf("  Memory Select Error: %d\n\n",
+			(ddr->err_detect & ECC_ERROR_DETECT_MSE) ? 1 : 0);
+
+	/* Capture data */
+	printf("Memory Error Address Capture: 0x%08lx\n", ddr->capture_address);
+	printf("Memory Data Path Read Capture High/Low: %08lx %08lx\n",
+			ddr->capture_data_hi, ddr->capture_data_lo);
+	printf("Memory Data Path Read Capture ECC: 0x%02x\n\n",
+		ddr->capture_ecc & CAPTURE_ECC_ECE);
+
+	printf("Memory Error Attributes Capture:\n");
+	printf("  Data Beat Number: %d\n",
+			(ddr->capture_attributes & ECC_CAPT_ATTR_BNUM) >> ECC_CAPT_ATTR_BNUM_SHIFT);
+	printf("  Transaction Size: %d\n",
+			(ddr->capture_attributes & ECC_CAPT_ATTR_TSIZ) >> ECC_CAPT_ATTR_TSIZ_SHIFT);
+	printf("  Transaction Source: %d\n",
+			(ddr->capture_attributes & ECC_CAPT_ATTR_TSRC) >> ECC_CAPT_ATTR_TSRC_SHIFT);
+	printf("  Transaction Type: %d\n",
+			(ddr->capture_attributes & ECC_CAPT_ATTR_TTYP) >> ECC_CAPT_ATTR_TTYP_SHIFT);
+	printf("  Error Information Valid: %d\n\n",
+			ddr->capture_attributes & ECC_CAPT_ATTR_VLD);
+}
+
+int do_ecc ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+	volatile ddr8349_t *ddr = &immap->ddr;
+	volatile u32 val;
+	u64 *addr, count, val64;
+	register u64 *i;
+	
+	if (argc > 4) {
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+	
+	if (argc == 2) {
+		if (strcmp(argv[1], "status") == 0) {
+			ecc_print_status();
+			return 0;
+		} else if (strcmp(argv[1], "captureclear") == 0) {
+			ddr->capture_address = 0;
+			ddr->capture_data_hi = 0;
+			ddr->capture_data_lo = 0;
+			ddr->capture_ecc = 0;
+			ddr->capture_attributes = 0;
+			return 0;
+		}
+	} 
+	
+	if (argc == 3) {
+		if (strcmp(argv[1], "sbecnt") == 0) {
+			val = simple_strtoul(argv[2], NULL, 10);
+			if (val > 255) {
+				printf("Incorrect Counter value, should be 0..255\n");
+				return 1;
+			}
+
+			val = (val << ECC_ERROR_MAN_SBEC_SHIFT);
+			val |= (ddr->err_sbe & ECC_ERROR_MAN_SBET);
+
+			ddr->err_sbe = val;
+			return 0;
+		} else if (strcmp(argv[1], "sbethr") == 0) {
+			val = simple_strtoul(argv[2], NULL, 10);
+			if (val > 255) {
+				printf("Incorrect Counter value, should be 0..255\n");
+				return 1;
+			}
+
+			val = (val << ECC_ERROR_MAN_SBET_SHIFT);
+			val |= (ddr->err_sbe & ECC_ERROR_MAN_SBEC);
+
+			ddr->err_sbe = val;
+			return 0;
+		} else if (strcmp(argv[1], "errdisable") == 0) {
+			val = ddr->err_disable;
+
+			if (strcmp(argv[2], "+sbe") == 0) {
+				val |= ECC_ERROR_DISABLE_SBED;
+			} else if (strcmp(argv[2], "+mbe") == 0) {
+				val |= ECC_ERROR_DISABLE_MBED;
+			} else if (strcmp(argv[2], "+mse") == 0) {
+				val |= ECC_ERROR_DISABLE_MSED;
+			} else if (strcmp(argv[2], "+all") == 0) {
+				val |= (ECC_ERROR_DISABLE_SBED | 
+					ECC_ERROR_DISABLE_MBED | 
+					ECC_ERROR_DISABLE_MSED);
+			} else if (strcmp(argv[2], "-sbe") == 0) {
+				val &= ~ECC_ERROR_DISABLE_SBED;
+			} else if (strcmp(argv[2], "-mbe") == 0) {
+				val &= ~ECC_ERROR_DISABLE_MBED;
+			} else if (strcmp(argv[2], "-mse") == 0) {
+				val &= ~ECC_ERROR_DISABLE_MSED;
+			} else if (strcmp(argv[2], "-all") == 0) {
+				val &= ~(ECC_ERROR_DISABLE_SBED | 
+					ECC_ERROR_DISABLE_MBED | 
+					ECC_ERROR_DISABLE_MSED);
+			} else {
+				printf("Incorrect err_disable field\n");
+				return 1;
+			}
+
+			ddr->err_disable = val;
+			__asm__ __volatile__ ("sync");
+			__asm__ __volatile__ ("isync");
+			return 0;
+		} else if (strcmp(argv[1], "errdetectclr") == 0) {
+			val = ddr->err_detect;
+
+			if (strcmp(argv[2], "mme") == 0) {
+				val |= ECC_ERROR_DETECT_MME;
+			} else if (strcmp(argv[2], "sbe") == 0) {
+				val |= ECC_ERROR_DETECT_SBE;
+			} else if (strcmp(argv[2], "mbe") == 0) {
+				val |= ECC_ERROR_DETECT_MBE;
+			} else if (strcmp(argv[2], "mse") == 0) {
+				val |= ECC_ERROR_DETECT_MSE;
+			} else if (strcmp(argv[2], "all") == 0) {
+				val |= (ECC_ERROR_DETECT_MME |
+					ECC_ERROR_DETECT_MBE |
+					ECC_ERROR_DETECT_SBE |
+					ECC_ERROR_DETECT_MSE);
+			} else {
+				printf("Incorrect err_detect field\n");
+				return 1;
+			}
+
+			ddr->err_detect = val;
+			return 0;
+		} else if (strcmp(argv[1], "injectdatahi") == 0) {
+			val = simple_strtoul(argv[2], NULL, 16);
+
+			ddr->data_err_inject_hi = val;
+			return 0;
+		} else if (strcmp(argv[1], "injectdatalo") == 0) {
+			val = simple_strtoul(argv[2], NULL, 16);
+
+			ddr->data_err_inject_lo = val;
+			return 0;
+		} else if (strcmp(argv[1], "injectecc") == 0) {
+			val = simple_strtoul(argv[2], NULL, 16);
+			if (val > 0xff) {
+				printf("Incorrect ECC inject mask, should be 0x00..0xff\n");
+				return 1;
+			}
+			val |= (ddr->ecc_err_inject & ~ECC_ERR_INJECT_EEIM);
+
+			ddr->ecc_err_inject = val;
+			return 0;
+		} else if (strcmp(argv[1], "inject") == 0) {
+			val = ddr->ecc_err_inject;
+
+			if (strcmp(argv[2], "en") == 0)
+				val |= ECC_ERR_INJECT_EIEN;
+			else if (strcmp(argv[2], "dis") == 0)
+				val &= ~ECC_ERR_INJECT_EIEN;
+			else
+				printf("Incorrect command\n");
+
+			ddr->ecc_err_inject = val;
+			__asm__ __volatile__ ("sync");
+			__asm__ __volatile__ ("isync");
+			return 0;
+		} else if (strcmp(argv[1], "mirror") == 0) {
+			val = ddr->ecc_err_inject;
+
+			if (strcmp(argv[2], "en") == 0)
+				val |= ECC_ERR_INJECT_EMB;
+			else if (strcmp(argv[2], "dis") == 0)
+				val &= ~ECC_ERR_INJECT_EMB;
+			else
+				printf("Incorrect command\n");
+
+			ddr->ecc_err_inject = val;
+			return 0;
+		}
+	}
+
+	if (argc == 4) {
+		if (strcmp(argv[1], "test") == 0) {
+			addr = (u64 *)simple_strtoul(argv[2], NULL, 16);
+			count = simple_strtoul(argv[3], NULL, 16);
+
+			if ((u32)addr % 8) {
+				printf("Address not alligned on double word boundary\n");
+				return 1;
+			}
+
+			disable_interrupts();
+			icache_disable();
+
+			for (i = addr; i < addr + count; i++) {
+				/* enable injects */
+				ddr->ecc_err_inject |= ECC_ERR_INJECT_EIEN;
+				__asm__ __volatile__ ("sync");
+				__asm__ __volatile__ ("isync");
+
+				/* write memory location injecting errors */
+				*i = 0x1122334455667788ULL;
+				__asm__ __volatile__ ("sync");
+
+				/* disable injects */
+				ddr->ecc_err_inject &= ~ECC_ERR_INJECT_EIEN;
+				__asm__ __volatile__ ("sync");
+				__asm__ __volatile__ ("isync");
+
+				/* read data, this generates ECC error */
+				val64 = *i;
+				__asm__ __volatile__ ("sync");
+
+				/* disable errors for ECC */
+				ddr->err_disable |= ~ECC_ERROR_ENABLE;
+				__asm__ __volatile__ ("sync");
+				__asm__ __volatile__ ("isync");
+
+				/* re-initialize memory, write the location again
+				 * NOT injecting errors this time */
+				*i = 0xcafecafecafecafeULL;
+				__asm__ __volatile__ ("sync");
+
+				/* enable errors for ECC */
+				ddr->err_disable &= ECC_ERROR_ENABLE;
+				__asm__ __volatile__ ("sync");
+				__asm__ __volatile__ ("isync");
+			}
+
+			icache_enable();
+			enable_interrupts();
+
+			return 0;
+		}
+	}
+
+	printf ("Usage:\n%s\n", cmdtp->usage);
+	return 1;
+}
+
+U_BOOT_CMD(
+	ecc,     4,     0,      do_ecc,
+	"ecc     - support for DDR ECC features\n",
+	"status              - print out status info\n"
+	"ecc captureclear        - clear capture regs data\n"
+	"ecc sbecnt <val>        - set Single-Bit Error counter\n"
+	"ecc sbethr <val>        - set Single-Bit Threshold\n"
+	"ecc errdisable <flag>   - clear/set disable Memory Error Disable, flag:\n"
+	"  [-|+]sbe - Single-Bit Error\n"
+	"  [-|+]mbe - Multiple-Bit Error\n"
+	"  [-|+]mse - Memory Select Error\n"
+	"  [-|+]all - all errors\n"
+	"ecc errdetectclr <flag> - clear Memory Error Detect, flag:\n"
+	"  mme - Multiple Memory Errors\n"
+	"  sbe - Single-Bit Error\n"
+	"  mbe - Multiple-Bit Error\n"
+	"  mse - Memory Select Error\n"
+	"  all - all errors\n"
+	"ecc injectdatahi <hi>  - set Memory Data Path Error Injection Mask High\n"
+	"ecc injectdatalo <lo>  - set Memory Data Path Error Injection Mask Low\n"
+	"ecc injectecc <ecc>    - set ECC Error Injection Mask\n"
+	"ecc inject <en|dis>    - enable/disable error injection\n"
+	"ecc mirror <en|dis>    - enable/disable mirror byte\n"
+	"ecc test <addr> <cnt>  - test mem region:\n"
+	"  - enables injects\n"
+	"  - writes pattern injecting errors\n"
+	"  - disables injects\n"
+	"  - reads pattern back, generates error\n"
+	"  - re-inits memory"
+);
+#endif /* if defined(CONFIG_DDR_ECC) && defined(CONFIG_DDR_ECC_CMD) */

board/mpc8349emds/u-boot.lds

@@ -0,0 +1,123 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc83xx/start.o	(.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
+ENTRY(_start)

board/netstar/Makefile

@@ -80,6 +80,6 @@ distclean:	clean
 .depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
 		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
 
--include .depend
+sinclude .depend
 
 #########################################################################

board/netstar/flash.c

@@ -230,7 +230,7 @@ out:
  * Copy memory to flash
  */
 
-volatile static int write_hword(flash_info_t *info, ulong dest, ushort data)
+static int write_hword(flash_info_t *info, ulong dest, ushort data)
 {
 	vu_short *addr = (vu_short *) dest;
 	ushort result;

board/netstar/nand.c

@@ -48,10 +48,12 @@ static void netstar_nand_hwcontrol(struct mtd_info *mtd, int cmd)
 /*
  *	chip R/B detection
  */
+/***
 static int netstar_nand_ready(struct mtd_info *mtd)
 {
 	return (*(volatile ushort *)GPIO_DATA_INPUT_REG) & 0x02;
 }
+***/
 
 void board_nand_init(struct nand_chip *nand)
 {

board/shannon/flash.c

@@ -315,7 +315,7 @@ outahere:
  * Copy memory to flash
  */
 
-volatile static int write_word (flash_info_t *info, ulong dest, ulong data)
+static int write_word (flash_info_t *info, ulong dest, ulong data)
 {
     vu_long *addr = (vu_long *)dest;
     ulong result;

board/smdk2400/flash.c

@@ -353,8 +353,7 @@ outahere:
  * Copy memory to flash
  */
 
-volatile static int write_word (flash_info_t * info, ulong dest,
-								ulong data)
+static int write_word (flash_info_t * info, ulong dest, ulong data)
 {
 	vu_long *addr = (vu_long *) dest;
 	ulong result;

board/stamp/Makefile

@@ -0,0 +1,68 @@
+#
+# U-boot - Makefile
+#
+# Copyright (c) 2005 blackfin.uclinux.org
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o stamp.o
+SOBJS	=
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/stamp/config.mk

@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x07FC0000
+PLATFORM_CPPFLAGS += -I$(TOPDIR)

board/stamp/stamp.c

@@ -0,0 +1,275 @@
+/*
+ * U-boot - stamp.c STAMP board specific routines
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mem_init.h>
+#include "stamp.h"
+
+#define STATUS_LED_OFF 0
+#define STATUS_LED_ON  1
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+# define SHOW_BOOT_PROGRESS(arg)	show_boot_progress(arg)
+#else
+# define SHOW_BOOT_PROGRESS(arg)
+#endif
+
+int checkboard (void)
+{
+	printf ("CPU:   ADSP BF533 Rev.: 0.%d\n", *pCHIPID >> 28);
+	printf ("Board: ADI BF533 Stamp board\n");
+	printf ("       Support: http://blackfin.uclinux.org/\n");
+	printf ("       Richard Klingler <richard@uclinux.net>\n");
+	return 0;
+}
+
+long int initdram (int board_type)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+#ifdef DEBUG
+	printf ("SDRAM attributes:\n");
+	printf ("  tRCD:%d Cycles; tRP:%d Cycles; tRAS:%d Cycles; tWR:%d Cycles; "
+		"CAS Latency:%d cycles\n",
+		(SDRAM_tRCD >> 15),
+		(SDRAM_tRP >> 11),
+		(SDRAM_tRAS >> 6),
+		(SDRAM_tWR >> 19),
+		(SDRAM_CL >> 2));
+	printf ("SDRAM Begin: 0x%x\n", CFG_SDRAM_BASE);
+	printf ("Bank size = %d MB\n", 128);
+#endif
+	gd->bd->bi_memstart = CFG_SDRAM_BASE;
+	gd->bd->bi_memsize = CFG_MAX_RAM_SIZE;
+	return (gd->bd->bi_memsize);
+}
+
+void swap_to (int device_id)
+{
+
+	if (device_id == ETHERNET) {
+		*pFIO_DIR = PF0;
+		asm ("ssync;");
+		*pFIO_FLAG_S = PF0;
+		asm ("ssync;");
+	} else if (device_id == FLASH) {
+		*pFIO_DIR = (PF4 | PF3 | PF2 | PF1 | PF0);
+		*pFIO_FLAG_S = (PF4 | PF3 | PF2);
+		*pFIO_MASKA_D = (PF8 | PF6 | PF5);
+		*pFIO_MASKB_D = (PF7);
+		*pFIO_POLAR = (PF8 | PF6 | PF5);
+		*pFIO_EDGE = (PF8 | PF7 | PF6 | PF5);
+		*pFIO_INEN = (PF8 | PF7 | PF6 | PF5);
+		*pFIO_FLAG_D = (PF4 | PF3 | PF2);
+		asm ("ssync;");
+	} else {
+		printf ("Unknown bank to switch\n");
+	}
+
+	return;
+}
+
+#if defined(CONFIG_MISC_INIT_R)
+/* miscellaneous platform dependent initialisations */
+int misc_init_r (void)
+{
+	int i;
+	int cf_stat = 0;
+
+	/* Check whether CF card is inserted */
+	*pFIO_EDGE = FIO_EDGE_CF_BITS;
+	*pFIO_POLAR = FIO_POLAR_CF_BITS;
+	for (i = 0; i < 0x300; i++)
+		asm ("nop;");
+
+	if ((*pFIO_FLAG_S) & CF_STAT_BITS) {
+		cf_stat = 0;
+	} else {
+		cf_stat = 1;
+	}
+
+	*pFIO_EDGE = FIO_EDGE_BITS;
+	*pFIO_POLAR = FIO_POLAR_BITS;
+
+
+	if (cf_stat) {
+		printf ("Booting from COMPACT flash\n");
+
+		/* Set cycle time for CF */
+		*(volatile unsigned long *) ambctl1 = CF_AMBCTL1VAL;
+
+		for (i = 0; i < 0x1000; i++)
+			asm ("nop;");
+		for (i = 0; i < 0x1000; i++)
+			asm ("nop;");
+		for (i = 0; i < 0x1000; i++)
+			asm ("nop;");
+
+		serial_setbrg ();
+		ide_init ();
+
+		setenv ("bootargs", "");
+		setenv ("bootcmd",
+			"fatload ide 0:1 0x1000000 uImage-stamp;bootm 0x1000000;bootm 0x20100000");
+	} else {
+		printf ("Booting from FLASH\n");
+	}
+
+	return 1;
+}
+#endif
+
+#ifdef CONFIG_STAMP_CF
+
+void cf_outb (unsigned char val, volatile unsigned char *addr)
+{
+	/*
+	 * Set PF1 PF0 respectively to 0 1 to divert address
+	 * to the expansion memory banks
+	 */
+	*pFIO_FLAG_S = CF_PF0;
+	*pFIO_FLAG_C = CF_PF1;
+	asm ("ssync;");
+
+	*(addr) = val;
+	asm ("ssync;");
+
+	/* Setback PF1 PF0 to 0 0 to address external
+	 * memory banks  */
+	*(volatile unsigned short *) pFIO_FLAG_C = CF_PF1_PF0;
+	asm ("ssync;");
+}
+
+unsigned char cf_inb (volatile unsigned char *addr)
+{
+	volatile unsigned char c;
+
+	*pFIO_FLAG_S = CF_PF0;
+	*pFIO_FLAG_C = CF_PF1;
+	asm ("ssync;");
+
+	c = *(addr);
+	asm ("ssync;");
+
+	*pFIO_FLAG_C = CF_PF1_PF0;
+	asm ("ssync;");
+
+	return c;
+}
+
+void cf_insw (unsigned short *sect_buf, unsigned short *addr, int words)
+{
+	int i;
+
+	*pFIO_FLAG_S = CF_PF0;
+	*pFIO_FLAG_C = CF_PF1;
+	asm ("ssync;");
+
+	for (i = 0; i < words; i++) {
+		*(sect_buf + i) = *(addr);
+		asm ("ssync;");
+	}
+
+	*pFIO_FLAG_C = CF_PF1_PF0;
+	asm ("ssync;");
+}
+
+void cf_outsw (unsigned short *addr, unsigned short *sect_buf, int words)
+{
+	int i;
+
+	*pFIO_FLAG_S = CF_PF0;
+	*pFIO_FLAG_C = CF_PF1;
+	asm ("ssync;");
+
+	for (i = 0; i < words; i++) {
+		*(addr) = *(sect_buf + i);
+		asm ("ssync;");
+	}
+
+	*pFIO_FLAG_C = CF_PF1_PF0;
+	asm ("ssync;");
+}
+#endif
+
+void stamp_led_set (int LED1, int LED2, int LED3)
+{
+	*pFIO_INEN &= ~(PF2 | PF3 | PF4);
+	*pFIO_DIR |= (PF2 | PF3 | PF4);
+
+	if (LED1 == STATUS_LED_OFF)
+		*pFIO_FLAG_S = PF2;
+	else
+		*pFIO_FLAG_C = PF2;
+	if (LED2 == STATUS_LED_OFF)
+		*pFIO_FLAG_S = PF3;
+	else
+		*pFIO_FLAG_C = PF3;
+	if (LED3 == STATUS_LED_OFF)
+		*pFIO_FLAG_S = PF4;
+	else
+		*pFIO_FLAG_C = PF4;
+	asm ("ssync;");
+}
+
+void show_boot_progress (int status)
+{
+	switch (status) {
+	case 1:
+		stamp_led_set (STATUS_LED_OFF, STATUS_LED_OFF, STATUS_LED_ON);
+		break;
+	case 2:
+		stamp_led_set (STATUS_LED_OFF, STATUS_LED_ON, STATUS_LED_OFF);
+		break;
+	case 3:
+		stamp_led_set (STATUS_LED_OFF, STATUS_LED_ON, STATUS_LED_ON);
+		break;
+	case 4:
+		stamp_led_set (STATUS_LED_ON, STATUS_LED_OFF, STATUS_LED_OFF);
+		break;
+	case 5:
+	case 6:
+		stamp_led_set (STATUS_LED_ON, STATUS_LED_OFF, STATUS_LED_ON);
+		break;
+	case 7:
+	case 8:
+		stamp_led_set (STATUS_LED_ON, STATUS_LED_ON, STATUS_LED_OFF);
+		break;
+	case 9:
+	case 10:
+	case 11:
+	case 12:
+	case 13:
+	case 14:
+	case 15:
+		stamp_led_set (STATUS_LED_OFF, STATUS_LED_OFF,
+			       STATUS_LED_OFF);
+		break;
+	default:
+		stamp_led_set (STATUS_LED_ON, STATUS_LED_ON, STATUS_LED_ON);
+		break;
+	}
+}

board/stamp/stamp.h

@@ -0,0 +1,57 @@
+/*
+ * U-boot - stamp.h
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __STAMP_H__
+#define __STAMP_H__
+
+extern void init_Flags(void);
+
+extern volatile unsigned long *ambctl0;
+extern volatile unsigned long *ambctl1;
+extern volatile unsigned long *amgctl;
+
+extern unsigned long pll_div_fact;
+extern void serial_setbrg(void);
+extern void pll_set(int vco, int crystal_frq, int pll_div);
+
+/* Definitions used in  Compact Flash Boot support */
+#define FIO_EDGE_CF_BITS 	0x0000
+#define FIO_POLAR_CF_BITS 	0x0000
+#define	FIO_EDGE_BITS  		0x1E0
+#define	FIO_POLAR_BITS  	0x160
+
+/* Compact flash status bits in status register */
+#define CF_STAT_BITS 		0x00000060
+
+/* CF Flags used to switch between expansion and external
+ * memory banks
+ */
+#define CF_PF0			0x0001
+#define CF_PF1			0x0002
+#define CF_PF1_PF0		0x0003
+
+#endif

board/stamp/u-boot.lds

@@ -0,0 +1,147 @@
+/*
+ * U-boot - u-boot.lds
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(bfin)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector before the environment sector. If it throws 	*/
+    /* an error during compilation remove an object here to get	*/
+    /* it linked after the configuration sector.		*/
+
+    cpu/bf533/start.o		(.text)
+    cpu/bf533/start1.o		(.text)
+    cpu/bf533/traps.o		(.text)
+    cpu/bf533/interrupt.o	(.text)
+    cpu/bf533/serial.o		(.text)
+    common/dlmalloc.o		(.text)
+    lib_generic/vsprintf.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_generic/zlib.o		(.text)
+
+    . = DEFINED(env_offset) ? env_offset : .;
+    common/environment.o	(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/trab/Makefile

@@ -47,7 +47,7 @@ trab_fkt.srec:	trab_fkt.o rs485.o tsc2000.o $(LIB)
 	$(OBJCOPY) -O srec $(<:.o=) $@
 
 trab_fkt.bin:	trab_fkt.srec
-	$(OBJCOPY) -O binary $< $@ 2>/dev/null
+	$(OBJCOPY) -I srec -O binary $< $@
 
 clean:
 	rm -f $(SOBJS) $(OBJS)

board/trab/flash.c

@@ -308,8 +308,7 @@ outahere:
  * Copy memory to flash
  */
 
-volatile static int write_word (flash_info_t * info, ulong dest,
-								ulong data)
+static int write_word (flash_info_t * info, ulong dest, ulong data)
 {
 	vu_long *addr = (vu_long *) dest;
 	ulong result;

board/versatile/split_by_variant.sh

@@ -36,5 +36,5 @@ fi
 # ---------------------------------------------------------
 # Complete the configuration
 # ---------------------------------------------------------
-./mkconfig -a versatile arm arm926ejs versatile
+./mkconfig -a versatile arm arm926ejs versatile NULL versatile
 echo "Variant:: $variant"

board/xilinx/xilinx_enet/emac_adapter.c

@@ -39,7 +39,6 @@
 
 #include <common.h>
 #include <net.h>
-#include <configs/ml300.h>
 #include "xparameters.h"
 #include "xemac.h"
 

board/xilinx/xilinx_iic/iic_adapter.c

@@ -40,7 +40,6 @@
 #include <common.h>
 #include <environment.h>
 #include <net.h>
-#include <configs/ml300.h>
 #include "xparameters.h"
 
 #ifdef CFG_ENV_IS_IN_EEPROM

board/zpc1900/config.mk

@@ -27,4 +27,4 @@
 # ZPC.1900 board
 #
 
-TEXT_BASE = 0xFFE00000
+TEXT_BASE = 0xFE000000

board/zpc1900/zpc1900.c

@@ -2,7 +2,7 @@
  * (C) Copyright 2001-2003
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
- * (C) Copyright 2003 Arabella Software Ltd.
+ * (C) Copyright 2003-2005 Arabella Software Ltd.
  * Yuli Barcohen <yuli@arabellasw.com>
  *
  * See file CREDITS for list of people who contributed to this
@@ -27,9 +27,6 @@
 #include <common.h>
 #include <ioports.h>
 #include <mpc8260.h>
-#include <asm/m8260_pci.h>
-#include <i2c.h>
-#include <spd.h>
 #include <miiphy.h>
 
 /*
@@ -167,8 +164,8 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,   0,   0,   0,   0   }, /* PD18 */
 	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
 	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
-	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
-	/* PD14 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SCL */
+	/* PD15 */ {   0,   1,   1,   0,   1,   0   }, /* I2C SDA */
+	/* PD14 */ {   0,   1,   1,   0,   1,   0   }, /* I2C SCL */
 	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
 	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
 	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
@@ -231,11 +228,10 @@ long int initdram(int board_type)
 	vu_char *ramaddr;
 	uchar c = 0xFF;
 	long int msize = CFG_SDRAM_SIZE;
-	uint psdmr = CFG_PSDMR;
 	int i;
 
 	if (bcsr[4] & BCSR_PCI_MODE) { /* PCI mode selected by JP9 */
-		immap->im_clkrst.car_sccr |= M826X_SCCR_PCI_MODE_EN;
+		immap->im_clkrst.car_sccr |= SCCR_PCI_MODE;
 		immap->im_siu_conf.sc_siumcr =
 			(immap->im_siu_conf.sc_siumcr & ~SIUMCR_LBPC11)
 			| SIUMCR_LBPC01;
@@ -255,10 +251,10 @@ long int initdram(int board_type)
 	*/
 	if ((immap->im_siu_conf.sc_siumcr & SIUMCR_LBPC11) == SIUMCR_LBPC00) {
 		memctl->memc_lsrt  = CFG_LSRT;
-		memctl->memc_or4   = 0xFFC01480;
-		memctl->memc_br4   = CFG_LSDRAM_BASE | 0x00001861;
-		memctl->memc_lsdmr = CFG_LSDMR | PSDMR_OP_PREA;
+		memctl->memc_or4   = CFG_LSDRAM_OR;
+		memctl->memc_br4   = CFG_LSDRAM_BR;
 		ramaddr = (vu_char *)CFG_LSDRAM_BASE;
+		memctl->memc_lsdmr = CFG_LSDMR | PSDMR_OP_PREA;
 		*ramaddr = c;
 		memctl->memc_lsdmr = CFG_LSDMR | PSDMR_OP_CBRR;
 		for (i = 0; i < 8; i++)
@@ -271,8 +267,8 @@ long int initdram(int board_type)
 
 	/* Initialise 60x bus SDRAM */
 	memctl->memc_psrt = CFG_PSRT;
-	memctl->memc_or2  = 0xFC0028C0;
-	memctl->memc_br2  = CFG_SDRAM_BASE | 0x00000041;
+	memctl->memc_or2  = CFG_PSDRAM_OR;
+	memctl->memc_br2  = CFG_PSDRAM_BR;
 	/*
 	 * The mode data for Mode Register Write command must appear on
 	 * the address lines during a mode-set cycle. It is driven by
@@ -283,15 +279,15 @@ long int initdram(int board_type)
 	 * length must be 4.
 	 */
 	ramaddr = (vu_char *)(CFG_SDRAM_BASE |
-			      ((psdmr & PSDMR_CL_MSK) << 7) | 0x10);
-	memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; /* Precharge all banks */
+			      ((CFG_PSDMR & PSDMR_CL_MSK) << 7) | 0x10);
+	memctl->memc_psdmr = CFG_PSDMR | PSDMR_OP_PREA; /* Precharge all banks */
 	*ramaddr = c;
-	memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; /* CBR refresh */
+	memctl->memc_psdmr = CFG_PSDMR | PSDMR_OP_CBRR; /* CBR refresh */
 	for (i = 0; i < 8; i++)
 		*ramaddr = c;
-	memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;  /* Mode Register write */
+	memctl->memc_psdmr = CFG_PSDMR | PSDMR_OP_MRW;  /* Mode Register write */
 	*ramaddr = c;
-	memctl->memc_psdmr = psdmr | PSDMR_RFEN;    /* Refresh enable */
+	memctl->memc_psdmr = CFG_PSDMR | PSDMR_RFEN;    /* Refresh enable */
 	*ramaddr = c;
 #endif /* CFG_RAMBOOT */
 

common/cmd_bootm.c

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2002
+ * (C) Copyright 2000-2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -140,6 +140,10 @@ static boot_os_Fcn do_bootm_lynxkdi;
 extern void lynxkdi_boot( image_header_t * );
 #endif
 
+#ifndef CFG_BOOTM_LEN
+#define CFG_BOOTM_LEN	0x800000	/* use 8MByte as default max gunzip size */
+#endif
+
 image_header_t header;
 
 ulong load_addr = CFG_LOAD_ADDR;		/* Default Load Address */
@@ -150,7 +154,7 @@ int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	ulong	addr;
 	ulong	data, len, checksum;
 	ulong  *len_ptr;
-	uint	unc_len = 0x400000;
+	uint	unc_len = CFG_BOOTM_LEN;
 	int	i, verify;
 	char	*name, *s;
 	int	(*appl)(int, char *[]);
@@ -252,6 +256,8 @@ int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	if (hdr->ih_arch != IH_CPU_MICROBLAZE)
 #elif defined(__nios2__)
 	if (hdr->ih_arch != IH_CPU_NIOS2)
+#elif defined(__blackfin__)
+	if (hdr->ih_arch != IH_CPU_BLACKFIN)
 #else
 # error Unknown CPU type
 #endif
@@ -606,7 +612,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 #endif /* CONFIG_MPC5xxx */
 	}
 
-	kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong))hdr->ih_ep;
+	kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong)) ntohl(hdr->ih_ep);
 
 	/*
 	 * Check if there is an initrd image
@@ -621,7 +627,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 		/* Copy header so we can blank CRC field for re-calculation */
 		memmove (&header, (char *)addr, sizeof(image_header_t));
 
-		if (hdr->ih_magic  != IH_MAGIC) {
+		if (ntohl(hdr->ih_magic)  != IH_MAGIC) {
 			puts ("Bad Magic Number\n");
 			SHOW_BOOT_PROGRESS (-10);
 			do_reset (cmdtp, flag, argc, argv);
@@ -630,7 +636,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 		data = (ulong)&header;
 		len  = sizeof(image_header_t);
 
-		checksum = hdr->ih_hcrc;
+		checksum = ntohl(hdr->ih_hcrc);
 		hdr->ih_hcrc = 0;
 
 		if (crc32 (0, (uchar *)data, len) != checksum) {
@@ -644,7 +650,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 		print_image_hdr (hdr);
 
 		data = addr + sizeof(image_header_t);
-		len  = hdr->ih_size;
+		len  = ntohl(hdr->ih_size);
 
 		if (verify) {
 			ulong csum = 0;
@@ -670,7 +676,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 			csum = crc32 (0, (uchar *)data, len);
 #endif	/* CONFIG_HW_WATCHDOG || CONFIG_WATCHDOG */
 
-			if (csum != hdr->ih_dcrc) {
+			if (csum != ntohl(hdr->ih_dcrc)) {
 				puts ("Bad Data CRC\n");
 				SHOW_BOOT_PROGRESS (-12);
 				do_reset (cmdtp, flag, argc, argv);
@@ -819,7 +825,7 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 	(*kernel) (kbd, initrd_start, initrd_end, cmd_start, cmd_end);
 
 #else
-	ft_setup(of_flat_tree, OF_FLAT_TREE_MAX_SIZE, kbd);
+	ft_setup(of_flat_tree, OF_FLAT_TREE_MAX_SIZE, kbd, initrd_start, initrd_end);
 	/* ft_dump_blob(of_flat_tree); */
 
 #if defined(CFG_INIT_RAM_LOCK) && !defined(CONFIG_E500)
@@ -828,12 +834,16 @@ do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
 	/*
 	 * Linux Kernel Parameters:
 	 *   r3: ptr to OF flat tree, followed by the board info data
-	 *   r4: initrd_start or 0 if no initrd
-	 *   r5: initrd_end - unused if r4 is 0
-	 *   r6: Start of command line string
-	 *   r7: End   of command line string
+	 *   r4: physical pointer to the kernel itself
+	 *   r5: NULL
+	 *   r6: NULL
+	 *   r7: NULL
 	 */
-	(*kernel) ((bd_t *)of_flat_tree, initrd_start, initrd_end, cmd_start, cmd_end);
+	if (getenv("disable_of") != NULL)
+		(*kernel) ((bd_t *)of_flat_tree, initrd_start, initrd_end,
+			cmd_start, cmd_end);
+	else
+		(*kernel) ((bd_t *)of_flat_tree, (ulong)kernel, 0, 0, 0);
 
 #endif
 }
@@ -902,7 +912,7 @@ do_bootm_netbsd (cmd_tbl_t *cmdtp, int flag,
 		cmdline = "";
 	}
 
-	loader = (void (*)(bd_t *, image_header_t *, char *, char *)) hdr->ih_ep;
+	loader = (void (*)(bd_t *, image_header_t *, char *, char *)) ntohl(hdr->ih_ep);
 
 	printf ("## Transferring control to NetBSD stage-2 loader (at address %08lx) ...\n",
 		(ulong)loader);
@@ -1364,7 +1374,7 @@ do_bootm_rtems (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[],
 	image_header_t *hdr = &header;
 	void	(*entry_point)(bd_t *);
 
-	entry_point = (void (*)(bd_t *)) hdr->ih_ep;
+	entry_point = (void (*)(bd_t *)) ntohl(hdr->ih_ep);
 
 	printf ("## Transferring control to RTEMS (at address %08lx) ...\n",
 		(ulong)entry_point);
@@ -1387,7 +1397,7 @@ do_bootm_vxworks (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[],
 	image_header_t *hdr = &header;
 	char str[80];
 
-	sprintf(str, "%x", hdr->ih_ep); /* write entry-point into string */
+	sprintf(str, "%x", ntohl(hdr->ih_ep)); /* write entry-point into string */
 	setenv("loadaddr", str);
 	do_bootvx(cmdtp, 0, 0, NULL);
 }
@@ -1400,7 +1410,7 @@ do_bootm_qnxelf (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[],
 	char *local_args[2];
 	char str[16];
 
-	sprintf(str, "%x", hdr->ih_ep); /* write entry-point into string */
+	sprintf(str, "%x", ntohl(hdr->ih_ep)); /* write entry-point into string */
 	local_args[0] = argv[0];
 	local_args[1] = str;	/* and provide it via the arguments */
 	do_bootelf(cmdtp, 0, 2, local_args);

common/cmd_doc.c

@@ -250,7 +250,7 @@ int do_docboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 		print_image_hdr (hdr);
 
-		cnt = (hdr->ih_size + sizeof(image_header_t));
+		cnt = (ntohl(hdr->ih_size) + sizeof(image_header_t));
 		cnt -= SECTORSIZE;
 	} else {
 		puts ("\n** Bad Magic Number **\n");

common/cmd_fdc.c

@@ -836,13 +836,13 @@ int do_fdcboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		return 1;
 	}
 	hdr = (image_header_t *)addr;
-	if (hdr->ih_magic  != IH_MAGIC) {
+	if (ntohl(hdr->ih_magic)  != IH_MAGIC) {
 		printf ("Bad Magic Number\n");
 		return 1;
 	}
 	print_image_hdr(hdr);
 
-	imsize= hdr->ih_size+sizeof(image_header_t);
+	imsize= ntohl(hdr->ih_size)+sizeof(image_header_t);
 	nrofblk=imsize/512;
 	if((imsize%512)>0)
 		nrofblk++;

common/cmd_nand.c

@@ -717,7 +717,7 @@ int do_nandboot (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		cnt = (ntohl(hdr->ih_size) + sizeof(image_header_t));
 		cnt -= SECTORSIZE;
 	} else {
-		printf ("\n** Bad Magic Number 0x%x **\n", hdr->ih_magic);
+		printf ("\n** Bad Magic Number 0x%x **\n", ntohl(hdr->ih_magic));
 		SHOW_BOOT_PROGRESS (-1);
 		return 1;
 	}

common/command.c

@@ -42,6 +42,8 @@ U_BOOT_CMD(
 	NULL
 );
 
+#if (CONFIG_COMMANDS & CFG_CMD_ECHO)
+
 int
 do_echo (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
@@ -74,6 +76,8 @@ U_BOOT_CMD(
 	"    - echo args to console; \\c suppresses newline\n"
 );
 
+#endif	/*  CFG_CMD_ECHO */
+
 #ifdef CFG_HUSH_PARSER
 
 int

common/env_nand.c

@@ -111,7 +111,8 @@ int env_init(void)
 #ifdef CFG_ENV_OFFSET_REDUND
 int saveenv(void)
 {
-	int total, ret = 0;
+	ulong total;
+	int ret = 0;
 
 	DECLARE_GLOBAL_DATA_PTR;
 
@@ -146,7 +147,8 @@ int saveenv(void)
 #else /* ! CFG_ENV_OFFSET_REDUND */
 int saveenv(void)
 {
-	int total, ret = 0;
+	ulong total;
+	int ret = 0;
 
 	puts ("Erasing Nand...");
 	if (nand_erase(&nand_info[0], CFG_ENV_OFFSET, CFG_ENV_SIZE))
@@ -154,8 +156,7 @@ int saveenv(void)
 
 	puts ("Writing to Nand... ");
 	total = CFG_ENV_SIZE;
-	ret = nand_write(&nand_info[0], CFG_ENV_OFFSET, &total,
-			(u_char*) env_ptr);
+	ret = nand_write(&nand_info[0], CFG_ENV_OFFSET, &total, (u_char*)env_ptr);
 	if (ret || total != CFG_ENV_SIZE)
 		return 1;
 
@@ -169,7 +170,8 @@ int saveenv(void)
 void env_relocate_spec (void)
 {
 #if !defined(ENV_IS_EMBEDDED)
-	int crc1_ok = 0, crc2_ok = 0, total;
+	ulong total;
+	int crc1_ok = 0, crc2_ok = 0;
 	env_t *tmp_env1, *tmp_env2;
 
 	DECLARE_GLOBAL_DATA_PTR;
@@ -227,12 +229,12 @@ void env_relocate_spec (void)
 void env_relocate_spec (void)
 {
 #if !defined(ENV_IS_EMBEDDED)
-	int ret, total;
+	ulong total;
+	int ret;
 
 	total = CFG_ENV_SIZE;
-	ret = nand_read(&nand_info[0], CFG_ENV_OFFSET, &total,
-			(u_char*) env_ptr);
-	if (ret || total != CFG_ENV_SIZE)
+	ret = nand_read(&nand_info[0], CFG_ENV_OFFSET, &total, (u_char*)env_ptr);
+  	if (ret || total != CFG_ENV_SIZE)
 		return use_default();
 
 	if (crc32(0, env_ptr->data, ENV_SIZE) != env_ptr->crc)

common/ft_build.c

@@ -163,7 +163,7 @@ void ft_add_rsvmap(struct ft_cxt *cxt, u64 physaddr, u64 size)
 	((u64 *) cxt->pres)[0] = cpu_to_be64(physaddr);	/* phys = 0, size = 0, terminate */
 	((u64 *) cxt->pres)[1] = cpu_to_be64(size);
 
-	cxt->pres += 18;	/* advance */
+	cxt->pres += 16;	/* advance */
 
 	((u64 *) cxt->pres)[0] = 0;	/* phys = 0, size = 0, terminate */
 	((u64 *) cxt->pres)[1] = 0;
@@ -529,6 +529,7 @@ extern uchar(*env_get_char) (int);
 
 #define BDM(x)	{	.name = #x, .offset = offsetof(bd_t, bi_ ##x ) }
 
+#ifdef CONFIG_OF_HAS_BD_T
 static const struct {
 	const char *name;
 	int offset;
@@ -574,19 +575,24 @@ static const struct {
 #endif
 	BDM(baudrate),
 };
+#endif
 
-void ft_setup(void *blob, int size, bd_t * bd)
+void ft_setup(void *blob, int size, bd_t * bd, ulong initrd_start, ulong initrd_end)
 {
-	DECLARE_GLOBAL_DATA_PTR;
-	u8 *end;
 	u32 *p;
 	int len;
 	struct ft_cxt cxt;
-	int i, k, nxt;
-	static char tmpenv[256];
-	char *s, *lval, *rval;
 	ulong clock;
-	uint32_t v;
+#if defined(CONFIG_OF_HAS_UBOOT_ENV)
+	int k, nxt;
+#endif
+#if defined(CONFIG_OF_HAS_BD_T)
+	u8 *end;
+#endif
+#if defined(CONFIG_OF_HAS_UBOOT_ENV) || defined(CONFIG_OF_HAS_BD_T)
+	int i;
+	static char tmpenv[256];
+#endif
 
 	/* disable OF tree; booting old kernel */
 	if (getenv("disable_of") != NULL) {
@@ -596,7 +602,8 @@ void ft_setup(void *blob, int size, bd_t * bd)
 
 	ft_begin(&cxt, blob, size);
 
-	/* fs_add_rsvmap not used */
+	if (initrd_start && initrd_end)
+		ft_add_rsvmap(&cxt, initrd_start, initrd_end - initrd_start + 1);
 
 	ft_begin_tree(&cxt);
 
@@ -610,9 +617,12 @@ void ft_setup(void *blob, int size, bd_t * bd)
 	/* back into root */
 	ft_backtrack_node(&cxt);
 
+#ifdef CONFIG_OF_HAS_UBOOT_ENV
 	ft_begin_node(&cxt, "u-boot-env");
 
 	for (i = 0; env_get_char(i) != '\0'; i = nxt + 1) {
+		char *s, *lval, *rval;
+
 		for (nxt = i; env_get_char(nxt) != '\0'; ++nxt) ;
 		s = tmpenv;
 		for (k = i; k < nxt && s < &tmpenv[sizeof(tmpenv) - 1]; ++k)
@@ -629,12 +639,20 @@ void ft_setup(void *blob, int size, bd_t * bd)
 	}
 
 	ft_end_node(&cxt);
+#endif
 
 	ft_begin_node(&cxt, "chosen");
 
 	ft_prop_str(&cxt, "name", "chosen");
 	ft_prop_str(&cxt, "bootargs", getenv("bootargs"));
 	ft_prop_int(&cxt, "linux,platform", 0x600);	/* what is this? */
+	if (initrd_start && initrd_end) {
+		ft_prop_int(&cxt, "linux,initrd-start", initrd_start);
+		ft_prop_int(&cxt, "linux,initrd-end", initrd_end);
+	}
+#ifdef OF_STDOUT_PATH
+	ft_prop_str(&cxt, "linux,stdout-path", OF_STDOUT_PATH);
+#endif
 
 	ft_end_node(&cxt);
 
@@ -647,14 +665,19 @@ void ft_setup(void *blob, int size, bd_t * bd)
 	   ft_dump_blob(blob);
 	 */
 
+#ifdef CONFIG_OF_HAS_BD_T
 	/* paste the bd_t at the end of the flat tree */
 	end = (char *)blob +
 	    be32_to_cpu(((struct boot_param_header *)blob)->totalsize);
 	memcpy(end, bd, sizeof(*bd));
+#endif
 
 #ifdef CONFIG_PPC
 
+#ifdef CONFIG_OF_HAS_BD_T
 	for (i = 0; i < sizeof(bd_map)/sizeof(bd_map[0]); i++) {
+		uint32_t v;
+
 		sprintf(tmpenv, "/bd_t/%s", bd_map[i].name);
 		v = *(uint32_t *)((char *)bd + bd_map[i].offset);
 
@@ -670,6 +693,7 @@ void ft_setup(void *blob, int size, bd_t * bd)
 	p = ft_get_prop(blob, "/bd_t/ethspeed", &len);
 	if (p != NULL)
 		*p = cpu_to_be32((uint32_t) bd->bi_ethspeed);
+#endif
 
 	clock = bd->bi_intfreq;
 	p = ft_get_prop(blob, "/cpus/" OF_CPU "/clock-frequency", &len);
@@ -680,11 +704,14 @@ void ft_setup(void *blob, int size, bd_t * bd)
 	clock = OF_TBCLK;
 	p = ft_get_prop(blob, "/cpus/" OF_CPU "/timebase-frequency", &len);
 	if (p != NULL)
-		*p = cpu_to_be32(OF_TBCLK);
+		*p = cpu_to_be32(clock);
 #endif
-
 #endif				/* __powerpc__ */
 
+#ifdef CONFIG_OF_BOARD_SETUP
+	ft_board_setup(blob, bd);
+#endif
+
 	/*
 	   printf("final OF-tree\n");
 	   ft_dump_blob(blob);

common/lynxkdi.c

@@ -23,11 +23,11 @@
 #if defined(CONFIG_MPC8260) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
 void lynxkdi_boot ( image_header_t *hdr )
 {
-	void (*lynxkdi)(void) = (void(*)(void))hdr->ih_ep;
+	void (*lynxkdi)(void) = (void(*)(void)) ntohl(hdr->ih_ep);
 	lynxos_bootparms_t *parms = (lynxos_bootparms_t *)0x0020;
 	bd_t *kbd;
 	DECLARE_GLOBAL_DATA_PTR;
-	u32 *psz = (u32 *)(hdr->ih_load + 0x0204);
+	u32 *psz = (u32 *)(ntohl(hdr->ih_load) + 0x0204);
 
 	memset( parms, 0, sizeof(*parms));
 	kbd = gd->bd;
@@ -39,9 +39,9 @@ void lynxkdi_boot ( image_header_t *hdr )
 	/* Do a simple check for Bluecat so we can pass the
 	 * kernel command line parameters.
 	 */
-	if( le32_to_cpu(*psz) == hdr->ih_size ){
+	if( le32_to_cpu(*psz) == ntohl(hdr->ih_size) ){	/* FIXME: NOT SURE HERE ! */
 	    char *args;
-	    char *cmdline = (char *)(hdr->ih_load + 0x020c);
+	    char *cmdline = (char *)(ntohl(hdr->ih_load) + 0x020c);
 	    int len;
 
 	    printf("Booting Bluecat KDI ...\n");

common/main.c

@@ -919,7 +919,10 @@ int run_command (const char *cmd, int flag)
 		process_macros (token, finaltoken);
 
 		/* Extract arguments */
-		argc = parse_line (finaltoken, argv);
+		if ((argc = parse_line (finaltoken, argv)) == 0) {
+			rc = -1;	/* no command at all */
+			continue;
+		}
 
 		/* Look up command in command table */
 		if ((cmdtp = find_cmd(argv[0])) == NULL) {
@@ -945,9 +948,9 @@ int run_command (const char *cmd, int flag)
 				puts ("'bootd' recursion detected\n");
 				rc = -1;
 				continue;
-			}
-			else
+			} else {
 				flag |= CMD_FLAG_BOOTD;
+			}
 		}
 #endif	/* CFG_CMD_BOOTD */
 

common/soft_i2c.c

@@ -164,13 +164,10 @@ static void send_ack(int ack)
 	volatile immap_t *immr = (immap_t *)CFG_IMMR;
 #endif
 
-	I2C_ACTIVE;
 	I2C_SCL(0);
 	I2C_DELAY;
-
-	I2C_SDA(ack);
-
 	I2C_ACTIVE;
+	I2C_SDA(ack);
 	I2C_DELAY;
 	I2C_SCL(1);
 	I2C_DELAY;
@@ -288,7 +285,10 @@ int i2c_probe(uchar addr)
 {
 	int rc;
 
-	/* perform 1 byte read transaction */
+	/*
+	 * perform 1 byte write transaction with just address byte
+	 * (fake write)
+	 */
 	send_start();
 	rc = write_byte ((addr << 1) | 0);
 	send_stop();

config.mk

@@ -53,6 +53,10 @@ PLATFORM_CPPFLAGS+= -D__ARM__
 endif
 endif
 
+ifeq ($(ARCH),blackfin)
+PLATFORM_CPPFLAGS+= -D__BLACKFIN__ -mno-underscore
+endif
+
 ifdef	ARCH
 sinclude $(TOPDIR)/$(ARCH)_config.mk	# include architecture dependend rules
 endif

cpu/arm920t/at91rm9200/i2c.c

@@ -111,7 +111,7 @@ at91_xfer(unsigned char chip, unsigned int addr, int alen,
 int
 i2c_probe(unsigned char chip)
 {
-	char buffer[1];
+	unsigned char buffer[1];
 
 	return at91_xfer(chip, 0, 0, buffer, 1, 1);
 }
@@ -191,7 +191,7 @@ i2c_init(int speed, int slaveaddr)
 
 uchar i2c_reg_read(uchar i2c_addr, uchar reg)
 {
-	char buf;
+	unsigned char buf;
 
 	i2c_read(i2c_addr, reg, 1, &buf, 1);
 

cpu/arm920t/s3c24x0/usb_ohci.c

@@ -1647,7 +1647,8 @@ int usb_lowlevel_init(void)
 	}
 
 	/* FIXME this is a second HC reset; why?? */
-	writel (gohci.hc_control = OHCI_USB_RESET, &gohci.regs->control);
+	gohci.hc_control = OHCI_USB_RESET;
+	writel (gohci.hc_control, &gohci.regs->control);
 	wait_ms (10);
 
 	if (hc_start (&gohci) < 0) {

cpu/arm926ejs/interrupts.c

@@ -39,16 +39,6 @@
 #include <arm926ejs.h>
 #include <asm/proc-armv/ptrace.h>
 
-#define TIMER_LOAD_VAL 0xffffffff
-
-/* macro to read the 32 bit timer */
-#ifdef CONFIG_OMAP
-#define READ_TIMER (*(volatile ulong *)(CFG_TIMERBASE+8))
-#endif
-#ifdef CONFIG_VERSATILE
-#define READ_TIMER (*(volatile ulong *)(CFG_TIMERBASE+4))
-#endif
-
 #ifdef CONFIG_USE_IRQ
 /* enable IRQ interrupts */
 void enable_interrupts (void)
@@ -188,146 +178,14 @@ void do_irq (struct pt_regs *pt_regs)
 
 #else
 
-static ulong timestamp;
-static ulong lastdec;
-
 /* nothing really to do with interrupts, just starts up a counter. */
 int interrupt_init (void)
 {
-#ifdef CONFIG_OMAP
-	int32_t val;
-
-	/* Start the decrementer ticking down from 0xffffffff */
-	*((int32_t *) (CFG_TIMERBASE + LOAD_TIM)) = TIMER_LOAD_VAL;
-	val = MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | (CFG_PVT << MPUTIM_PTV_BIT);
-	*((int32_t *) (CFG_TIMERBASE + CNTL_TIMER)) = val;
-#endif	/* CONFIG_OMAP */
-
-#ifdef CONFIG_VERSATILE
-	*(volatile ulong *)(CFG_TIMERBASE + 0) = CFG_TIMER_RELOAD;	/* TimerLoad */
-	*(volatile ulong *)(CFG_TIMERBASE + 4) = CFG_TIMER_RELOAD;	/* TimerValue */
-	*(volatile ulong *)(CFG_TIMERBASE + 8) = 0x8C;
-#endif	/* CONFIG_VERSATILE */
-
-	/* init the timestamp and lastdec value */
-	reset_timer_masked();
-
-	return (0);
-}
-
-/*
- * timer without interrupts
- */
-
-void reset_timer (void)
-{
-	reset_timer_masked ();
-}
+	extern void timer_init(void);
 
-ulong get_timer (ulong base)
-{
-	return get_timer_masked () - base;
-}
+  	timer_init();
 
-void set_timer (ulong t)
-{
-	timestamp = t;
-}
-
-/* delay x useconds AND perserve advance timstamp value */
-void udelay (unsigned long usec)
-{
-	ulong tmo, tmp;
-
-	if(usec >= 1000){		/* if "big" number, spread normalization to seconds */
-		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
-		tmo *= CFG_HZ;		/* find number of "ticks" to wait to achieve target */
-		tmo /= 1000;		/* finish normalize. */
-	}else{				/* else small number, don't kill it prior to HZ multiply */
-		tmo = usec * CFG_HZ;
-		tmo /= (1000*1000);
-	}
-
-	tmp = get_timer (0);		/* get current timestamp */
-	if( (tmo + tmp + 1) < tmp )	/* if setting this fordward will roll time stamp */
-		reset_timer_masked ();	/* reset "advancing" timestamp to 0, set lastdec value */
-	else
-		tmo += tmp;		/* else, set advancing stamp wake up time */
-
-	while (get_timer_masked () < tmo)/* loop till event */
-		/*NOP*/;
-}
-
-void reset_timer_masked (void)
-{
-	/* reset time */
-	lastdec = READ_TIMER;  /* capure current decrementer value time */
-	timestamp = 0;	       /* start "advancing" time stamp from 0 */
-}
-
-ulong get_timer_masked (void)
-{
-	ulong now = READ_TIMER;		/* current tick value */
-
-	if (lastdec >= now) {		/* normal mode (non roll) */
-		/* normal mode */
-		timestamp += lastdec - now; /* move stamp fordward with absoulte diff ticks */
-	} else {			/* we have overflow of the count down timer */
-		/* nts = ts + ld + (TLV - now)
-		 * ts=old stamp, ld=time that passed before passing through -1
-		 * (TLV-now) amount of time after passing though -1
-		 * nts = new "advancing time stamp"...it could also roll and cause problems.
-		 */
-		timestamp += lastdec + TIMER_LOAD_VAL - now;
-	}
-	lastdec = now;
-
-	return timestamp;
-}
-
-/* waits specified delay value and resets timestamp */
-void udelay_masked (unsigned long usec)
-{
-	ulong tmo;
-	ulong endtime;
-	signed long diff;
-
-	if (usec >= 1000) {		/* if "big" number, spread normalization to seconds */
-		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
-		tmo *= CFG_HZ;		/* find number of "ticks" to wait to achieve target */
-		tmo /= 1000;		/* finish normalize. */
-	} else {			/* else small number, don't kill it prior to HZ multiply */
-		tmo = usec * CFG_HZ;
-		tmo /= (1000*1000);
-	}
-
-	endtime = get_timer_masked () + tmo;
-
-	do {
-		ulong now = get_timer_masked ();
-		diff = endtime - now;
-	} while (diff >= 0);
-}
-
-/*
- * This function is derived from PowerPC code (read timebase as long long).
- * On ARM it just returns the timer value.
- */
-unsigned long long get_ticks(void)
-{
-	return get_timer(0);
-}
-
-/*
- * This function is derived from PowerPC code (timebase clock frequency).
- * On ARM it returns the number of timer ticks per second.
- */
-ulong get_tbclk (void)
-{
-	ulong tbclk;
-
-	tbclk = CFG_HZ;
-	return tbclk;
+	return 0;
 }
 
 #endif /* CONFIG_INTEGRATOR */

cpu/arm926ejs/omap/Makefile

@@ -0,0 +1,43 @@
+#
+# (C) Copyright 2000-2005
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(SOC).a
+
+OBJS	= timer.o
+SOBJS	= reset.o
+
+all:	.depend $(LIB)
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+#########################################################################
+
+.depend:	Makefile $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

cpu/arm926ejs/omap/reset.S

@@ -0,0 +1,45 @@
+/*
+ *  armboot - Startup Code for ARM926EJS CPU-core
+ *
+ *  Copyright (c) 2003  Texas Instruments
+ *
+ *  ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------
+ *
+ *  Copyright (c) 2001	Marius Gröger <mag@sysgo.de>
+ *  Copyright (c) 2002	Alex Züpke <azu@sysgo.de>
+ *  Copyright (c) 2002	Gary Jennejohn <gj@denx.de>
+ *  Copyright (c) 2003	Richard Woodruff <r-woodruff2@ti.com>
+ *  Copyright (c) 2003	Kshitij <kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+	.align	5
+.globl reset_cpu
+reset_cpu:
+	ldr	r1, rstctl1	/* get clkm1 reset ctl */
+	mov	r3, #0x0
+	strh	r3, [r1]	/* clear it */
+	mov	r3, #0x8
+	strh	r3, [r1]	/* force dsp+arm reset */
+_loop_forever:
+	b	_loop_forever
+
+rstctl1:
+	.word	0xfffece10

cpu/arm926ejs/omap/timer.c

@@ -0,0 +1,177 @@
+/*
+ * (C) Copyright 2003
+ * Texas Instruments <www.ti.com>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * (C) Copyright 2002-2004
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * (C) Copyright 2004
+ * Philippe Robin, ARM Ltd. <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <arm926ejs.h>
+
+#define TIMER_LOAD_VAL 0xffffffff
+
+/* macro to read the 32 bit timer */
+#define READ_TIMER (*(volatile ulong *)(CFG_TIMERBASE+8))
+
+static ulong timestamp;
+static ulong lastdec;
+
+int timer_init (void)
+{
+	int32_t val;
+
+	/* Start the decrementer ticking down from 0xffffffff */
+	*((int32_t *) (CFG_TIMERBASE + LOAD_TIM)) = TIMER_LOAD_VAL;
+	val = MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | (CFG_PVT << MPUTIM_PTV_BIT);
+	*((int32_t *) (CFG_TIMERBASE + CNTL_TIMER)) = val;
+
+	/* init the timestamp and lastdec value */
+	reset_timer_masked();
+
+	return 0;
+}
+
+/*
+ * timer without interrupts
+ */
+
+void reset_timer (void)
+{
+	reset_timer_masked ();
+}
+
+ulong get_timer (ulong base)
+{
+	return get_timer_masked () - base;
+}
+
+void set_timer (ulong t)
+{
+	timestamp = t;
+}
+
+/* delay x useconds AND perserve advance timstamp value */
+void udelay (unsigned long usec)
+{
+	ulong tmo, tmp;
+
+	if(usec >= 1000){		/* if "big" number, spread normalization to seconds */
+		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
+		tmo *= CFG_HZ;		/* find number of "ticks" to wait to achieve target */
+		tmo /= 1000;		/* finish normalize. */
+	}else{				/* else small number, don't kill it prior to HZ multiply */
+		tmo = usec * CFG_HZ;
+		tmo /= (1000*1000);
+	}
+
+	tmp = get_timer (0);		/* get current timestamp */
+	if( (tmo + tmp + 1) < tmp )	/* if setting this fordward will roll time stamp */
+		reset_timer_masked ();	/* reset "advancing" timestamp to 0, set lastdec value */
+	else
+		tmo += tmp;		/* else, set advancing stamp wake up time */
+
+	while (get_timer_masked () < tmo)/* loop till event */
+		/*NOP*/;
+}
+
+void reset_timer_masked (void)
+{
+	/* reset time */
+	lastdec = READ_TIMER;  /* capure current decrementer value time */
+	timestamp = 0;	       /* start "advancing" time stamp from 0 */
+}
+
+ulong get_timer_masked (void)
+{
+	ulong now = READ_TIMER;		/* current tick value */
+
+	if (lastdec >= now) {		/* normal mode (non roll) */
+		/* normal mode */
+		timestamp += lastdec - now; /* move stamp fordward with absoulte diff ticks */
+	} else {			/* we have overflow of the count down timer */
+		/* nts = ts + ld + (TLV - now)
+		 * ts=old stamp, ld=time that passed before passing through -1
+		 * (TLV-now) amount of time after passing though -1
+		 * nts = new "advancing time stamp"...it could also roll and cause problems.
+		 */
+		timestamp += lastdec + TIMER_LOAD_VAL - now;
+	}
+	lastdec = now;
+
+	return timestamp;
+}
+
+/* waits specified delay value and resets timestamp */
+void udelay_masked (unsigned long usec)
+{
+	ulong tmo;
+	ulong endtime;
+	signed long diff;
+
+	if (usec >= 1000) {		/* if "big" number, spread normalization to seconds */
+		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
+		tmo *= CFG_HZ;		/* find number of "ticks" to wait to achieve target */
+		tmo /= 1000;		/* finish normalize. */
+	} else {			/* else small number, don't kill it prior to HZ multiply */
+		tmo = usec * CFG_HZ;
+		tmo /= (1000*1000);
+	}
+
+	endtime = get_timer_masked () + tmo;
+
+	do {
+		ulong now = get_timer_masked ();
+		diff = endtime - now;
+	} while (diff >= 0);
+}
+
+/*
+ * This function is derived from PowerPC code (read timebase as long long).
+ * On ARM it just returns the timer value.
+ */
+unsigned long long get_ticks(void)
+{
+	return get_timer(0);
+}
+
+/*
+ * This function is derived from PowerPC code (timebase clock frequency).
+ * On ARM it returns the number of timer ticks per second.
+ */
+ulong get_tbclk (void)
+{
+	ulong tbclk;
+
+	tbclk = CFG_HZ;
+	return tbclk;
+}

cpu/arm926ejs/start.S

@@ -392,25 +392,3 @@ fiq:
 	bl	do_fiq
 
 #endif
-
-# ifdef CONFIG_INTEGRATOR
-
-	/* Satisfied by Integrator routine (AP or CP) */
-
-#else
-
-	.align	5
-.globl reset_cpu
-reset_cpu:
-	ldr	r1, rstctl1	/* get clkm1 reset ctl */
-	mov	r3, #0x0
-	strh	r3, [r1]	/* clear it */
-	mov	r3, #0x8
-	strh	r3, [r1]	/* force dsp+arm reset */
-_loop_forever:
-	b	_loop_forever
-
-rstctl1:
-	.word	0xfffece10
-
-#endif /* #ifdef CONFIG_INTEGRATOR */

cpu/arm926ejs/versatile/Makefile

@@ -0,0 +1,43 @@
+#
+# (C) Copyright 2000-2005
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(SOC).a
+
+OBJS	= timer.o
+SOBJS	= reset.o
+
+all:	.depend $(LIB)
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+#########################################################################
+
+.depend:	Makefile $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

cpu/arm926ejs/versatile/reset.S

@@ -0,0 +1,45 @@
+/*
+ *  armboot - Startup Code for ARM926EJS CPU-core
+ *
+ *  Copyright (c) 2003  Texas Instruments
+ *
+ *  ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------
+ *
+ *  Copyright (c) 2001	Marius Gröger <mag@sysgo.de>
+ *  Copyright (c) 2002	Alex Züpke <azu@sysgo.de>
+ *  Copyright (c) 2002	Gary Jennejohn <gj@denx.de>
+ *  Copyright (c) 2003	Richard Woodruff <r-woodruff2@ti.com>
+ *  Copyright (c) 2003	Kshitij <kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+	.align	5
+.globl reset_cpu
+reset_cpu:
+	ldr	r1, rstctl1	/* get clkm1 reset ctl */
+	mov	r3, #0x0
+	strh	r3, [r1]	/* clear it */
+	mov	r3, #0x8
+	strh	r3, [r1]	/* force dsp+arm reset */
+_loop_forever:
+	b	_loop_forever
+
+rstctl1:
+	.word	0xfffece10

cpu/arm926ejs/versatile/timer.c

@@ -0,0 +1,175 @@
+/*
+ * (C) Copyright 2003
+ * Texas Instruments <www.ti.com>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * (C) Copyright 2002-2004
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * (C) Copyright 2004
+ * Philippe Robin, ARM Ltd. <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <arm926ejs.h>
+
+#define TIMER_LOAD_VAL 0xffffffff
+
+/* macro to read the 32 bit timer */
+#define READ_TIMER (*(volatile ulong *)(CFG_TIMERBASE+4))
+
+static ulong timestamp;
+static ulong lastdec;
+
+/* nothing really to do with interrupts, just starts up a counter. */
+int timer_init (void)
+{
+	*(volatile ulong *)(CFG_TIMERBASE + 0) = CFG_TIMER_RELOAD;	/* TimerLoad */
+	*(volatile ulong *)(CFG_TIMERBASE + 4) = CFG_TIMER_RELOAD;	/* TimerValue */
+	*(volatile ulong *)(CFG_TIMERBASE + 8) = 0x8C;
+
+	/* init the timestamp and lastdec value */
+	reset_timer_masked();
+
+	return 0;
+}
+
+/*
+ * timer without interrupts
+ */
+
+void reset_timer (void)
+{
+	reset_timer_masked ();
+}
+
+ulong get_timer (ulong base)
+{
+	return get_timer_masked () - base;
+}
+
+void set_timer (ulong t)
+{
+	timestamp = t;
+}
+
+/* delay x useconds AND perserve advance timstamp value */
+void udelay (unsigned long usec)
+{
+	ulong tmo, tmp;
+
+	if(usec >= 1000){		/* if "big" number, spread normalization to seconds */
+		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
+		tmo *= CFG_HZ;		/* find number of "ticks" to wait to achieve target */
+		tmo /= 1000;		/* finish normalize. */
+	}else{				/* else small number, don't kill it prior to HZ multiply */
+		tmo = usec * CFG_HZ;
+		tmo /= (1000*1000);
+	}
+
+	tmp = get_timer (0);		/* get current timestamp */
+	if( (tmo + tmp + 1) < tmp )	/* if setting this fordward will roll time stamp */
+		reset_timer_masked ();	/* reset "advancing" timestamp to 0, set lastdec value */
+	else
+		tmo += tmp;		/* else, set advancing stamp wake up time */
+
+	while (get_timer_masked () < tmo)/* loop till event */
+		/*NOP*/;
+}
+
+void reset_timer_masked (void)
+{
+	/* reset time */
+	lastdec = READ_TIMER;  /* capure current decrementer value time */
+	timestamp = 0;	       /* start "advancing" time stamp from 0 */
+}
+
+ulong get_timer_masked (void)
+{
+	ulong now = READ_TIMER;		/* current tick value */
+
+	if (lastdec >= now) {		/* normal mode (non roll) */
+		/* normal mode */
+		timestamp += lastdec - now; /* move stamp fordward with absoulte diff ticks */
+	} else {			/* we have overflow of the count down timer */
+		/* nts = ts + ld + (TLV - now)
+		 * ts=old stamp, ld=time that passed before passing through -1
+		 * (TLV-now) amount of time after passing though -1
+		 * nts = new "advancing time stamp"...it could also roll and cause problems.
+		 */
+		timestamp += lastdec + TIMER_LOAD_VAL - now;
+	}
+	lastdec = now;
+
+	return timestamp;
+}
+
+/* waits specified delay value and resets timestamp */
+void udelay_masked (unsigned long usec)
+{
+	ulong tmo;
+	ulong endtime;
+	signed long diff;
+
+	if (usec >= 1000) {		/* if "big" number, spread normalization to seconds */
+		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
+		tmo *= CFG_HZ;		/* find number of "ticks" to wait to achieve target */
+		tmo /= 1000;		/* finish normalize. */
+	} else {			/* else small number, don't kill it prior to HZ multiply */
+		tmo = usec * CFG_HZ;
+		tmo /= (1000*1000);
+	}
+
+	endtime = get_timer_masked () + tmo;
+
+	do {
+		ulong now = get_timer_masked ();
+		diff = endtime - now;
+	} while (diff >= 0);
+}
+
+/*
+ * This function is derived from PowerPC code (read timebase as long long).
+ * On ARM it just returns the timer value.
+ */
+unsigned long long get_ticks(void)
+{
+	return get_timer(0);
+}
+
+/*
+ * This function is derived from PowerPC code (timebase clock frequency).
+ * On ARM it returns the number of timer ticks per second.
+ */
+ulong get_tbclk (void)
+{
+	ulong tbclk;
+
+	tbclk = CFG_HZ;
+	return tbclk;
+}

cpu/bf533/Makefile

@@ -0,0 +1,46 @@
+# U-boot - Makefile
+#
+# Copyright (c) 2005 blackfin.uclinux.org
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(CPU).a
+
+START	= start.o start1.o interrupt.o cache.o cplbhdlr.o cplbmgr.o flush.o
+OBJS	= cpu.o traps.o ints.o serial.o interrupts.o
+
+all:	.depend $(START) $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(START:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(START:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

cpu/bf533/bf533_serial.h

@@ -0,0 +1,78 @@
+/*
+ * U-boot - bf533_serial.h Serial Driver defines
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * This file is based on
+ * bf533_serial.h: Definitions for the BlackFin BF533 DSP serial driver.
+ * Copyright (C) 2003	Bas Vermeulen <bas@buyways.nl>
+ * 			BuyWays B.V. (www.buyways.nl)
+ *
+ * Based heavily on:
+ * blkfinserial.h: Definitions for the BlackFin DSP serial driver.
+ *
+ * Copyright (C) 2001	Tony Z. Kou	tonyko@arcturusnetworks.com
+ * Copyright (C) 2001   Arcturus Networks Inc. <www.arcturusnetworks.com>
+ *
+ * Based on code from 68328serial.c which was:
+ * Copyright (C) 1995       David S. Miller    <davem@caip.rutgers.edu>
+ * Copyright (C) 1998       Kenneth Albanowski <kjahds@kjahds.com>
+ * Copyright (C) 1998, 1999 D. Jeff Dionne     <jeff@uclinux.org>
+ * Copyright (C) 1999       Vladimir Gurevich  <vgurevic@cisco.com>
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _Bf533_SERIAL_H
+#define _Bf533_SERIAL_H
+
+#include <linux/config.h>
+#include <asm/blackfin.h>
+
+#define SYNC_ALL	__asm__ __volatile__ ("ssync;\n")
+#define ACCESS_LATCH	*pUART_LCR |= UART_LCR_DLAB;
+#define ACCESS_PORT_IER	*pUART_LCR &= (~UART_LCR_DLAB);
+
+void serial_setbrg(void);
+static void local_put_char(char ch);
+void calc_baud(void);
+void serial_setbrg(void);
+int serial_init(void);
+void serial_putc(const char c);
+int serial_tstc(void);
+int serial_getc(void);
+void serial_puts(const char *s);
+static void local_put_char(char ch);
+
+extern int get_clock(void);
+int baud_table[5] = {9600, 19200, 38400, 57600, 115200};
+
+struct {
+	unsigned char dl_high;
+	unsigned char dl_low;
+} hw_baud_table[5];
+
+#ifdef CONFIG_STAMP
+extern unsigned long pll_div_fact;
+#endif
+
+#endif

cpu/bf533/cache.S

@@ -0,0 +1,125 @@
+
+
+#define ASSEMBLY
+#include <asm/linkage.h>
+#include <asm/cpu/def_LPBlackfin.h>
+
+.text
+.align 2
+ENTRY(blackfin_icache_flush_range)
+	R2 = -32;
+	R2 = R0 & R2;
+	P0 = R2;
+	P1 = R1;
+	CSYNC;
+1:
+	IFLUSH[P0++];
+	CC = P0 < P1(iu);
+	IF CC JUMP 1b(bp);
+	IFLUSH[P0];
+	SSYNC;
+	RTS;
+
+ENTRY(blackfin_dcache_flush_range)
+	R2 = -32;
+	R2 = R0 & R2;
+	P0 = R2;
+	P1 = R1;
+	CSYNC;
+1:
+	FLUSH[P0++];
+	CC = P0 < P1(iu);
+	IF CC JUMP 1b(bp);
+	FLUSH[P0];
+	SSYNC;
+	RTS;
+
+ENTRY(_icache_invalidate)
+ENTRY(invalidate_entire_icache)
+	[--SP] = ( R7:5);
+
+	P0.L = (IMEM_CONTROL & 0xFFFF);
+	P0.H = (IMEM_CONTROL >> 16);
+	R7 = [P0];
+
+	/* Clear the IMC bit , All valid bits in the instruction
+	 * cache are set to the invalid state
+	 */
+	BITCLR(R7,IMC_P);
+	CLI R6;
+	SSYNC;		/* SSYNC required before invalidating cache. */
+	.align 8;
+	[P0] = R7;
+	SSYNC;
+	STI R6;
+
+	/* Configures the instruction cache agian */
+	R6 = (IMC | ENICPLB);
+	R7 = R7 | R6;
+
+	CLI R6;
+	SSYNC;		/* SSYNC required before writing to IMEM_CONTROL. */
+	.align 8;
+	[P0] = R7;
+	SSYNC;
+	STI R6;
+
+	( R7:5) = [SP++];
+	RTS;
+
+/* Invalidate the Entire Data cache by
+ * clearing DMC[1:0] bits
+ */
+ENTRY(invalidate_entire_dcache)
+ENTRY(_dcache_invalidate)
+	[--SP] = ( R7:6);
+
+	P0.L = (DMEM_CONTROL & 0xFFFF);
+	P0.H = (DMEM_CONTROL >> 16);
+	R7 = [P0];
+
+	/* Clear the DMC[1:0] bits, All valid bits in the data
+	 * cache are set to the invalid state
+	 */
+	BITCLR(R7,DMC0_P);
+	BITCLR(R7,DMC1_P);
+	CLI R6;
+	SSYNC;		/* SSYNC required before writing to DMEM_CONTROL. */
+	.align 8;
+	[P0] = R7;
+	SSYNC;
+	STI R6;
+
+	/* Configures the data cache again */
+
+	R6 = (ACACHE_BCACHE | ENDCPLB | PORT_PREF0);
+	R7 = R7 | R6;
+
+	CLI R6;
+	SSYNC;		/* SSYNC required before writing to DMEM_CONTROL. */
+	.align 8;
+	[P0] = R7;
+	SSYNC;
+	STI R6;
+
+	( R7:6) = [SP++];
+	RTS;
+
+ENTRY(blackfin_dcache_invalidate_range)
+	R2 = -32;
+	R2 = R0 & R2;
+	P0 = R2;
+	P1 = R1;
+	CSYNC;
+1:
+	FLUSHINV[P0++];
+	CC = P0 < P1 (iu);
+	IF CC JUMP 1b (bp);
+
+	/* If the data crosses a cache line, then we'll be pointing to
+	** the last cache line, but won't have flushed/invalidated it yet, so do
+	** one more.
+	*/
+	FLUSHINV[P0];
+	SSYNC;
+	RTS;

cpu/bf533/config.mk

@@ -0,0 +1,27 @@
+# U-boot - config.mk
+#
+# Copyright (c) 2005 blackfin.uclinux.org
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+PLATFORM_RELFLAGS += -ffixed-P5

cpu/bf533/cplbhdlr.S

@@ -0,0 +1,193 @@
+/* Copyright (C) 2003 Analog Devices, Inc. All Rights Reserved.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.
+ *
+ * Blackfin BF533/2.6 support : LG Soft India
+ */
+
+
+/* Include an exception handler to invoke the CPLB manager
+ */
+
+#include <asm-blackfin/linkage.h>
+#include <asm/cplb.h>
+#include <asm/entry.h>
+
+
+.text
+
+.globl _cplb_hdr;
+.type _cplb_hdr, STT_FUNC;
+.extern _cplb_mgr;
+.type _cplb_mgr, STT_FUNC;
+.extern __unknown_exception_occurred;
+.type __unknown_exception_occurred, STT_FUNC;
+.extern __cplb_miss_all_locked;
+.type __cplb_miss_all_locked, STT_FUNC;
+.extern __cplb_miss_without_replacement;
+.type __cplb_miss_without_replacement, STT_FUNC;
+.extern __cplb_protection_violation;
+.type __cplb_protection_violation, STT_FUNC;
+.extern panic_pv;
+
+.align 2;
+
+ENTRY(_cplb_hdr)
+	SSYNC;
+	[--SP] = ( R7:0, P5:0 );
+	[--SP] = ASTAT;
+	[--SP] = SEQSTAT;
+	[--SP] = I0;
+	[--SP] = I1;
+	[--SP] = I2;
+	[--SP] = I3;
+	[--SP] = LT0;
+	[--SP] = LB0;
+	[--SP] = LC0;
+	[--SP] = LT1;
+	[--SP] = LB1;
+	[--SP] = LC1;
+	R2 = SEQSTAT;
+
+	/*Mask the contents of SEQSTAT and leave only EXCAUSE in R2*/
+	R2 <<= 26;
+	R2 >>= 26;
+
+	R1 = 0x23; /* Data access CPLB protection violation */
+	CC = R2 == R1;
+	IF !CC JUMP not_data_write;
+	R0 = 2;		/* is a write to data space*/
+	JUMP is_icplb_miss;
+
+not_data_write:
+	R1 = 0x2C; /* CPLB miss on an instruction fetch */
+	CC = R2 == R1;
+	R0 = 0;		/* is_data_miss == False*/
+	IF CC JUMP is_icplb_miss;
+
+	R1 = 0x26;
+	CC = R2 == R1;
+	IF !CC JUMP unknown;
+
+	R0 = 1;		/* is_data_miss == True*/
+
+is_icplb_miss:
+
+#if ( defined (CONFIG_BLKFIN_CACHE) || defined (CONFIG_BLKFIN_DCACHE))
+#if ( defined (CONFIG_BLKFIN_CACHE) && !defined (CONFIG_BLKFIN_DCACHE))
+	R1 = CPLB_ENABLE_ICACHE;
+#endif
+#if ( !defined (CONFIG_BLKFIN_CACHE) && defined (CONFIG_BLKFIN_DCACHE))
+	R1 = CPLB_ENABLE_DCACHE;
+#endif
+#if ( defined (CONFIG_BLKFIN_CACHE) && defined (CONFIG_BLKFIN_DCACHE))
+	R1 = CPLB_ENABLE_DCACHE | CPLB_ENABLE_ICACHE;
+#endif
+#else
+	R1 = 0;
+#endif
+
+	[--SP] = RETS;
+	CALL _cplb_mgr;
+	RETS = [SP++];
+	CC = R0 == 0;
+	IF !CC JUMP not_replaced;
+	LC1 = [SP++];
+	LB1 = [SP++];
+	LT1 = [SP++];
+	LC0 = [SP++];
+	LB0 = [SP++];
+	LT0 = [SP++];
+	I3 = [SP++];
+	I2 = [SP++];
+	I1 = [SP++];
+	I0 = [SP++];
+	SEQSTAT = [SP++];
+	ASTAT = [SP++];
+	( R7:0, P5:0 ) = [SP++];
+	RTS;
+
+unknown:
+	[--SP] = RETS;
+	CALL __unknown_exception_occurred;
+	RETS = [SP++];
+	JUMP unknown;
+not_replaced:
+	CC = R0 == CPLB_NO_UNLOCKED;
+	IF !CC JUMP next_check;
+	[--SP] = RETS;
+	CALL __cplb_miss_all_locked;
+	RETS = [SP++];
+next_check:
+	CC = R0 == CPLB_NO_ADDR_MATCH;
+	IF !CC JUMP next_check2;
+	[--SP] = RETS;
+	CALL __cplb_miss_without_replacement;
+	RETS = [SP++];
+	JUMP not_replaced;
+next_check2:
+	CC = R0 == CPLB_PROT_VIOL;
+	IF !CC JUMP strange_return_from_cplb_mgr;
+	[--SP] = RETS;
+	CALL __cplb_protection_violation;
+	RETS = [SP++];
+	JUMP not_replaced;
+strange_return_from_cplb_mgr:
+	IDLE;
+	CSYNC;
+	JUMP strange_return_from_cplb_mgr;
+
+/************************************
+ * Diagnostic exception handlers
+ */
+
+__cplb_miss_all_locked:
+	sp += -12;
+	R0 = CPLB_NO_UNLOCKED;
+	call panic_bfin;
+	SP += 12;
+	RTS;
+
+ __cplb_miss_without_replacement:
+	sp += -12;
+	R0 = CPLB_NO_ADDR_MATCH;
+	call panic_bfin;
+	SP += 12;
+	RTS;
+
+__cplb_protection_violation:
+	sp += -12;
+	R0 = CPLB_PROT_VIOL;
+	call panic_bfin;
+	SP += 12;
+	RTS;
+
+__unknown_exception_occurred:
+
+	/* This function is invoked by the default exception
+	 * handler, if it does not recognise the kind of
+	 * exception that has occurred. In other words, the
+	 * default handler only handles some of the system's
+	 * exception types, and it does not expect any others
+	 * to occur. If your application is going to be using
+	 * other kinds of exceptions, you must replace the
+	 * default handler with your own, that handles all the
+	 * exceptions you will use.
+	 *
+	 * Since there's nothing we can do, we just loop here
+	 * at what we hope is a suitably informative label.
+	 */
+
+	IDLE;
+do_not_know_what_to_do:
+	CSYNC;
+	JUMP __unknown_exception_occurred;
+
+	RTS;
+.__unknown_exception_occurred.end:
+.global __unknown_exception_occurred;
+.type __unknown_exception_occurred, STT_FUNC;
+
+panic_bfin:
+	RTS;

cpu/bf533/cplbmgr.S

@@ -0,0 +1,601 @@
+/*This file is subject to the terms and conditions of the GNU General Public
+ * License.
+ *
+ * Blackfin BF533/2.6 support : LG Soft India
+ * Modification: Dec 07 2004
+ *	1. Correction in icheck_lock.  Valid lock entries were
+ *	   geting victimized, for instruction cplb replacement.
+ *	2. Setup loop's are modified as now toolchain support's P Indexed
+ *	   addressing
+ *	   :LG Soft India
+ *
+ */
+
+/* Usage: int _cplb_mgr(is_data_miss,int enable_cache)
+ * is_data_miss==2 => Mark as Dirty, write to the clean data page
+ * is_data_miss==1 => Replace a data CPLB.
+ * is_data_miss==0 => Replace an instruction CPLB.
+ *
+ * Returns:
+ * CPLB_RELOADED	=> Successfully updated CPLB table.
+ * CPLB_NO_UNLOCKED	=> All CPLBs are locked, so cannot be evicted.This indicates
+ *				that the CPLBs in the configuration tablei are badly
+ *				configured, as this should never occur.
+ * CPLB_NO_ADDR_MATCH	=> The address being accessed, that triggered the exception,
+ *				is not covered by any of the CPLBs in the configuration
+ *				table. The application isi presumably misbehaving.
+ * CPLB_PROT_VIOL	=> The address being accessed, that triggered thei exception,
+ *				was not a first-write to a clean Write Back Data page,
+ *				and so presumably is a genuine violation of the page's
+ *				protection attributes. The application is misbehaving.
+ */
+#define ASSEMBLY
+
+#include <asm-blackfin/linkage.h>
+#include <asm-blackfin/blackfin.h>
+#include <asm-blackfin/cplbtab.h>
+#include <asm-blackfin/cplb.h>
+
+.text
+
+.align 2;
+ENTRY(_cplb_mgr)
+
+	[--SP]=( R7:0,P5:0 );
+
+	CC = R0 == 2;
+	IF CC JUMP dcplb_write;
+
+	CC = R0 == 0;
+	IF !CC JUMP dcplb_miss_compare;
+
+	/* ICPLB Miss Exception. We need to choose one of the
+	* currently-installed CPLBs, and replace it with one
+	* from the configuration table.
+	*/
+
+	P4.L = (ICPLB_FAULT_ADDR & 0xFFFF);
+	P4.H = (ICPLB_FAULT_ADDR >> 16);
+
+	P1 = 16;
+	P5.L = page_size_table;
+	P5.H = page_size_table;
+
+	P0.L = (ICPLB_DATA0 & 0xFFFF);
+	P0.H = (ICPLB_DATA0 >> 16);
+	R4 = [P4];		/* Get faulting address*/
+	R6 = 64;		/* Advance past the fault address, which*/
+	R6 = R6 + R4;		/* we'll use if we find a match*/
+	R3 = ((16 << 8) | 2);	/* Extract mask, bits 16 and 17.*/
+
+	R5 = 0;
+isearch:
+
+	R1 = [P0-0x100];	/* Address for this CPLB */
+
+	R0 = [P0++];		/* Info for this CPLB*/
+	CC = BITTST(R0,0);	/* Is the CPLB valid?*/
+	IF !CC JUMP nomatch;	/* Skip it, if not.*/
+	CC = R4 < R1(IU);	/* If fault address less than page start*/
+	IF CC JUMP nomatch;	/* then skip this one.*/
+	R2 = EXTRACT(R0,R3.L) (Z);	/* Get page size*/
+	P1 = R2;
+	P1 = P5 + (P1<<2);	/* index into page-size table*/
+	R2 = [P1];		/* Get the page size*/
+	R1 = R1 + R2;		/* and add to page start, to get page end*/
+	CC = R4 < R1(IU);	/* and see whether fault addr is in page.*/
+	IF !CC R4 = R6;		/* If so, advance the address and finish loop.*/
+	IF !CC JUMP isearch_done;
+nomatch:
+	/* Go around again*/
+	R5 += 1;
+	CC = BITTST(R5, 4);	/* i.e CC = R5 >= 16*/
+	IF !CC JUMP isearch;
+
+isearch_done:
+	I0 = R4;		/* Fault address we'll search for*/
+
+	/* set up pointers */
+	P0.L = (ICPLB_DATA0 & 0xFFFF);
+	P0.H = (ICPLB_DATA0 >> 16);
+
+	/* The replacement procedure for ICPLBs */
+
+	P4.L = (IMEM_CONTROL & 0xFFFF);
+	P4.H = (IMEM_CONTROL >> 16);
+
+	/* disable cplbs */
+	R5 = [P4];		/* Control Register*/
+	BITCLR(R5,ENICPLB_P);
+	CLI R1;
+	SSYNC;		/* SSYNC required before writing to IMEM_CONTROL. */
+	.align 8;
+	[P4] = R5;
+	SSYNC;
+	STI R1;
+
+	R1 = -1;		/* end point comparison */
+	R3 = 16;		/* counter */
+
+	/* Search through CPLBs for first non-locked entry */
+	/* Overwrite it by moving everyone else up by 1 */
+icheck_lock:
+	R0 = [P0++];
+	R3 = R3 + R1;
+	CC = R3 == R1;
+	IF CC JUMP all_locked;
+	CC = BITTST(R0, 0);		/* an invalid entry is good */
+	IF !CC JUMP ifound_victim;
+	CC = BITTST(R0,1);		/* but a locked entry isn't */
+	IF CC JUMP icheck_lock;
+
+ifound_victim:
+#ifdef CONFIG_CPLB_INFO
+	R7 = [P0 - 0x104];
+	P2.L = ipdt_table;
+	P2.H = ipdt_table;
+	P3.L = ipdt_swapcount_table;
+	P3.H = ipdt_swapcount_table;
+	P3 += -4;
+icount:
+	R2 = [P2];	/* address from config table */
+	P2 += 8;
+	P3 += 8;
+	CC = R2==-1;
+	IF CC JUMP icount_done;
+	CC = R7==R2;
+	IF !CC JUMP icount;
+	R7 = [P3];
+	R7 += 1;
+	[P3] = R7;
+	CSYNC;
+icount_done:
+#endif
+	LC0=R3;
+	LSETUP(is_move,ie_move) LC0;
+is_move:
+	R0 = [P0];
+	[P0 - 4] = R0;
+	R0 = [P0 - 0x100];
+	[P0-0x104] = R0;
+ie_move:P0+=4;
+
+	/* We've made space in the ICPLB table, so that ICPLB15
+	 * is now free to be overwritten. Next, we have to determine
+	 * which CPLB we need to install, from the configuration
+	 * table. This is a matter of getting the start-of-page
+	 * addresses and page-lengths from the config table, and
+	 * determining whether the fault address falls within that
+	 * range.
+	 */
+
+	P2.L = ipdt_table;
+	P2.H = ipdt_table;
+#ifdef	CONFIG_CPLB_INFO
+	P3.L = ipdt_swapcount_table;
+	P3.H = ipdt_swapcount_table;
+	P3 += -8;
+#endif
+	P0.L = page_size_table;
+	P0.H = page_size_table;
+
+	/* Retrieve our fault address (which may have been advanced
+	 * because the faulting instruction crossed a page boundary).
+	 */
+
+	R0 = I0;
+
+	/* An extraction pattern, to get the page-size bits from
+	 * the CPLB data entry. Bits 16-17, so two bits at posn 16.
+	 */
+
+	R1 = ((16<<8)|2);
+inext:	R4 = [P2++];	/* address from config table */
+	R2 = [P2++];	/* data from config table */
+#ifdef	CONFIG_CPLB_INFO
+	P3 += 8;
+#endif
+
+	CC = R4 == -1;	/* End of config table*/
+	IF CC JUMP no_page_in_table;
+
+	/* See if failed address > start address */
+	CC = R4 <= R0(IU);
+	IF !CC JUMP inext;
+
+	/* extract page size (17:16)*/
+	R3 = EXTRACT(R2, R1.L) (Z);
+
+	/* add page size to addr to get range */
+
+	P5 = R3;
+	P5 = P0 + (P5 << 2);	/* scaled, for int access*/
+	R3 = [P5];
+	R3 = R3 + R4;
+
+	/* See if failed address < (start address + page size) */
+	CC = R0 < R3(IU);
+	IF !CC JUMP inext;
+
+	/* We've found a CPLB in the config table that covers
+	 * the faulting address, so install this CPLB into the
+	 * last entry of the table.
+	 */
+
+	P1.L = (ICPLB_DATA15 & 0xFFFF);		/*ICPLB_DATA15*/
+	P1.H = (ICPLB_DATA15 >> 16);
+	[P1] = R2;
+	[P1-0x100] = R4;
+#ifdef	CONFIG_CPLB_INFO
+	R3 = [P3];
+	R3 += 1;
+	[P3] = R3;
+#endif
+
+	/* P4 points to IMEM_CONTROL, and R5 contains its old
+	 * value, after we disabled ICPLBS. Re-enable them.
+	 */
+
+	BITSET(R5,ENICPLB_P);
+	CLI R2;
+	SSYNC;		/* SSYNC required before writing to IMEM_CONTROL. */
+	.align 8;
+	[P4] = R5;
+	SSYNC;
+	STI R2;
+
+	( R7:0,P5:0 ) = [SP++];
+	R0 = CPLB_RELOADED;
+	RTS;
+
+/* FAILED CASES*/
+no_page_in_table:
+	( R7:0,P5:0 ) = [SP++];
+	R0 = CPLB_NO_ADDR_MATCH;
+	RTS;
+all_locked:
+	( R7:0,P5:0 ) = [SP++];
+	R0 = CPLB_NO_UNLOCKED;
+	RTS;
+prot_violation:
+	( R7:0,P5:0 ) = [SP++];
+	R0 = CPLB_PROT_VIOL;
+	RTS;
+
+dcplb_write:
+
+	/* if a DCPLB is marked as write-back (CPLB_WT==0), and
+	 * it is clean (CPLB_DIRTY==0), then a write to the
+	 * CPLB's page triggers a protection violation. We have to
+	 * mark the CPLB as dirty, to indicate that there are
+	 * pending writes associated with the CPLB.
+	 */
+
+	P4.L = (DCPLB_STATUS & 0xFFFF);
+	P4.H = (DCPLB_STATUS >> 16);
+	P3.L = (DCPLB_DATA0 & 0xFFFF);
+	P3.H = (DCPLB_DATA0 >> 16);
+	R5 = [P4];
+
+	/* A protection violation can be caused by more than just writes
+	 * to a clean WB page, so we have to ensure that:
+	 * - It's a write
+	 * - to a clean WB page
+	 * - and is allowed in the mode the access occurred.
+	 */
+
+	CC = BITTST(R5, 16);	/* ensure it was a write*/
+	IF !CC JUMP prot_violation;
+
+	/* to check the rest, we have to retrieve the DCPLB.*/
+
+	/* The low half of DCPLB_STATUS is a bit mask*/
+
+	R2 = R5.L (Z);	/* indicating which CPLB triggered the event.*/
+	R3 = 30;	/* so we can use this to determine the offset*/
+	R2.L = SIGNBITS R2;
+	R2 = R2.L (Z);	/* into the DCPLB table.*/
+	R3 = R3 - R2;
+	P4 = R3;
+	P3 = P3 + (P4<<2);
+	R3 = [P3];	/* Retrieve the CPLB*/
+
+	/* Now we can check whether it's a clean WB page*/
+
+	CC = BITTST(R3, 14);	/* 0==WB, 1==WT*/
+	IF CC JUMP prot_violation;
+	CC = BITTST(R3, 7);	/* 0 == clean, 1 == dirty*/
+	IF CC JUMP prot_violation;
+
+	/* Check whether the write is allowed in the mode that was active.*/
+
+	R2 = 1<<3;		/* checking write in user mode*/
+	CC = BITTST(R5, 17);	/* 0==was user, 1==was super*/
+	R5 = CC;
+	R2 <<= R5;		/* if was super, check write in super mode*/
+	R2 = R3 & R2;
+	CC = R2 == 0;
+	IF CC JUMP prot_violation;
+
+	/* It's a genuine write-to-clean-page.*/
+
+	BITSET(R3, 7);		/* mark as dirty*/
+	[P3] = R3;		/* and write back.*/
+	CSYNC;
+	( R7:0,P5:0 ) = [SP++];
+	R0 = CPLB_RELOADED;
+	RTS;
+
+dcplb_miss_compare:
+
+	/* Data CPLB Miss event. We need to choose a CPLB to
+	 * evict, and then locate a new CPLB to install from the
+	 * config table, that covers the faulting address.
+	 */
+
+	P1.L = (DCPLB_DATA15 & 0xFFFF);
+	P1.H = (DCPLB_DATA15 >> 16);
+
+	P4.L = (DCPLB_FAULT_ADDR & 0xFFFF);
+	P4.H = (DCPLB_FAULT_ADDR >> 16);
+	R4 = [P4];
+	I0 = R4;
+
+	/* The replacement procedure for DCPLBs*/
+
+	R6 = R1;	/* Save for later*/
+
+	/* Turn off CPLBs while we work.*/
+	P4.L = (DMEM_CONTROL & 0xFFFF);
+	P4.H = (DMEM_CONTROL >> 16);
+	R5 = [P4];
+	BITCLR(R5,ENDCPLB_P);
+	CLI R0;
+	SSYNC;		/* SSYNC required before writing to DMEM_CONTROL. */
+	.align 8;
+	[P4] = R5;
+	SSYNC;
+	STI R0;
+
+	/* Start looking for a CPLB to evict. Our order of preference
+	 * is: invalid CPLBs, clean CPLBs, dirty CPLBs. Locked CPLBs
+	 * are no good.
+	 */
+
+	I1.L = (DCPLB_DATA0 & 0xFFFF);
+	I1.H = (DCPLB_DATA0 >> 16);
+	P1 = 3;
+	P2 = 16;
+	I2.L = dcplb_preference;
+	I2.H = dcplb_preference;
+	LSETUP(sdsearch1, edsearch1) LC0 = P1;
+sdsearch1:
+	R0 = [I2++];		/* Get the bits we're interested in*/
+	P0 = I1;		/* Go back to start of table*/
+	LSETUP (sdsearch2, edsearch2) LC1 = P2;
+sdsearch2:
+	R1 = [P0++];		/* Fetch each installed CPLB in turn*/
+	R2 = R1 & R0;		/* and test for interesting bits.*/
+	CC = R2 == 0;		/* If none are set, it'll do.*/
+	IF !CC JUMP skip_stack_check;
+
+	R2 = [P0 - 0x104];	/* R2 - PageStart */
+	P3.L = page_size_table; /* retrive end address */
+	P3.H = page_size_table; /* retrive end address */
+	R3 = 0x2;		/* 0th - position, 2 bits -length */
+	nop;			/*Anamoly 05000209*/
+	R7 = EXTRACT(R1,R3.l);
+	R7 = R7 << 2;		/* Page size index offset */
+	P5 = R7;
+	P3 = P3 + P5;
+	R7 = [P3];		/* page size in 1K bytes */
+
+	R7 = R7 << 0xA;		/* in bytes * 1024*/
+	R7 = R2 + R7;		/* R7 - PageEnd */
+	R4 = SP;		/* Test SP is in range */
+
+	CC = R7 < R4;		/* if PageEnd < SP */
+	IF CC JUMP dfound_victim;
+	R3 = 0x284;		/* stack length from start of trap till the point */
+				/* 20 stack locations for future modifications */
+	R4 = R4 + R3;
+	CC = R4 < R2;		/* if SP + stacklen < PageStart */
+	IF CC JUMP dfound_victim;
+skip_stack_check:
+
+edsearch2: NOP;
+edsearch1: NOP;
+
+	/* If we got here, we didn't find a DCPLB we considered
+	 * replacable, which means all of them were locked.
+	 */
+
+	JUMP all_locked;
+dfound_victim:
+
+#ifdef CONFIG_CPLB_INFO
+	R1 = [P0 - 0x104];
+	P2.L = dpdt_table;
+	P2.H = dpdt_table;
+	P3.L = dpdt_swapcount_table;
+	P3.H = dpdt_swapcount_table;
+	P3 += -4;
+dicount:
+	R2 = [P2];
+	P2 += 8;
+	P3 += 8;
+	CC = R2==-1;
+	IF CC JUMP dicount_done;
+	CC = R1==R2;
+	IF !CC JUMP dicount;
+	R1 = [P3];
+	R1 += 1;
+	[P3] = R1;
+	CSYNC;
+dicount_done:
+#endif
+
+	/* Clean down the hardware loops*/
+	R2 = 0;
+	LC1 = R2;
+	LC0 = R2;
+
+	/* There's a suitable victim in [P0-4] (because we've
+	 * advanced already). If it's a valid dirty write-back
+	 * CPLB, we need to flush the pending writes first.
+	 */
+
+	CC = BITTST(R1, 0);	/* Is it valid?*/
+	IF !CC JUMP Ddoverwrite;/* nope.*/
+	CC = BITTST(R1, 7);	/* Is it dirty?*/
+	IF !CC JUMP Ddoverwrite (BP);	/* Nope.*/
+	CC = BITTST(R1, 14);	/* Is it Write-Through?*/
+	IF CC JUMP Ddoverwrite; /* Yep*/
+
+	/* This is a dirty page, so we need to flush all writes
+	 * that are pending on the page.
+	 */
+
+	/* Retrieve the page start address*/
+	R0 = [P0 - 0x104];
+	[--sp] = rets;
+	CALL dcplb_flush;	/* R0==CPLB addr, R1==CPLB data*/
+	rets = [sp++];
+Ddoverwrite:
+
+	/* [P0-4] is a suitable victim CPLB, so we want to
+	 * overwrite it by moving all the following CPLBs
+	 * one space closer to the start.
+	 */
+
+	R1.L = ((DCPLB_DATA15+4) & 0xFFFF);		/*DCPLB_DATA15+4*/
+	R1.H = ((DCPLB_DATA15+4) >> 16);
+	R0 = P0;
+
+	/* If the victim happens to be in DCPLB15,
+	 * we don't need to move anything.
+	 */
+
+	CC = R1 == R0;
+	IF CC JUMP de_moved;
+	R1 = R1 - R0;
+	R1 >>= 2;
+	P1 = R1;
+	LSETUP(ds_move, de_move) LC0=P1;
+ds_move:
+	 R0 = [P0++];	/* move data */
+	[P0 - 8] = R0;
+	R0 = [P0-0x104] /* move address */
+de_move: [P0-0x108] = R0;
+
+	/* We've now made space in DCPLB15 for the new CPLB to be
+	 * installed. The next stage is to locate a CPLB in the
+	 * config table that covers the faulting address.
+	 */
+
+de_moved:NOP;
+	R0 = I0;		/* Our faulting address */
+
+	P2.L = dpdt_table;
+	P2.H = dpdt_table;
+#ifdef	CONFIG_CPLB_INFO
+	P3.L = dpdt_swapcount_table;
+	P3.H = dpdt_swapcount_table;
+	P3 += -8;
+#endif
+
+	P1.L = page_size_table;
+	P1.H = page_size_table;
+
+	/* An extraction pattern, to retrieve bits 17:16.*/
+
+	R1 = (16<<8)|2;
+dnext:	R4 = [P2++];	/* address */
+	R2 = [P2++];	/* data */
+#ifdef	CONFIG_CPLB_INFO
+	P3 += 8;
+#endif
+
+	CC = R4 == -1;
+	IF CC JUMP no_page_in_table;
+
+	/* See if failed address > start address */
+	CC = R4 <= R0(IU);
+	IF !CC JUMP dnext;
+
+	/* extract page size (17:16)*/
+	R3 = EXTRACT(R2, R1.L) (Z);
+
+	/* add page size to addr to get range */
+
+	P5 = R3;
+	P5 = P1 + (P5 << 2);
+	R3 = [P5];
+	R3 = R3 + R4;
+
+	/* See if failed address < (start address + page size) */
+	CC = R0 < R3(IU);
+	IF !CC JUMP dnext;
+
+	/* We've found the CPLB that should be installed, so
+	 * write it into CPLB15, masking off any caching bits
+	 * if necessary.
+	 */
+
+	P1.L = (DCPLB_DATA15 & 0xFFFF);
+	P1.H = (DCPLB_DATA15 >> 16);
+
+	/* If the DCPLB has cache bits set, but caching hasn't
+	 * been enabled, then we want to mask off the cache-in-L1
+	 * bit before installing. Moreover, if caching is off, we
+	 * also want to ensure that the DCPLB has WT mode set, rather
+	 * than WB, since WB pages still trigger first-write exceptions
+	 * even when not caching is off, and the page isn't marked as
+	 * cachable. Finally, we could mark the page as clean, not dirty,
+	 * but we choose to leave that decision to the user; if the user
+	 * chooses to have a CPLB pre-defined as dirty, then they always
+	 * pay the cost of flushing during eviction, but don't pay the
+	 * cost of first-write exceptions to mark the page as dirty.
+	 */
+
+#ifdef CONFIG_BLKFIN_WT
+	BITSET(R6, 14);		/* Set WT*/
+#endif
+
+	[P1] = R2;
+	[P1-0x100] = R4;
+#ifdef	CONFIG_CPLB_INFO
+	R3 = [P3];
+	R3 += 1;
+	[P3] = R3;
+#endif
+
+	/* We've installed the CPLB, so re-enable CPLBs. P4
+	 * points to DMEM_CONTROL, and R5 is the value we
+	 * last wrote to it, when we were disabling CPLBs.
+	 */
+
+	BITSET(R5,ENDCPLB_P);
+	CLI R2;
+	.align 8;
+	[P4] = R5;
+	SSYNC;
+	STI R2;
+
+	( R7:0,P5:0 ) = [SP++];
+	R0 = CPLB_RELOADED;
+	RTS;
+
+.data
+.align 4;
+page_size_table:
+.byte4	0x00000400;	/* 1K */
+.byte4	0x00001000;	/* 4K */
+.byte4	0x00100000;	/* 1M */
+.byte4	0x00400000;	/* 4M */
+
+.align 4;
+dcplb_preference:
+.byte4	0x00000001;	/* valid bit */
+.byte4	0x00000082;	/* dirty+lock bits */
+.byte4	0x00000002;	/* lock bit */

cpu/bf533/cpu.c

@@ -0,0 +1,189 @@
+/*
+ * U-boot - cpu.c CPU specific functions
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/blackfin.h>
+#include <command.h>
+#include <asm/entry.h>
+
+#define SSYNC() asm("ssync;")
+#define CACHE_ON 1
+#define CACHE_OFF 0
+
+/* Data Attibutes*/
+
+#define SDRAM_IGENERIC		(PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID)
+#define SDRAM_IKERNEL		(PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
+#define L1_IMEMORY            	(PAGE_SIZE_1MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)
+#define SDRAM_INON_CHBL		(PAGE_SIZE_4MB | CPLB_USER_RD | CPLB_VALID)
+
+#define ANOMALY_05000158		0x200
+#define SDRAM_DGENERIC          (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
+#define SDRAM_DNON_CHBL         (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158)
+#define SDRAM_DKERNEL           (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158)
+#define L1_DMEMORY              (PAGE_SIZE_4KB | CPLB_L1_CHBL | CPLB_L1_AOW | CPLB_WT | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158)
+#define SDRAM_EBIU              (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158)
+
+static unsigned int icplb_table[16][2]={
+			{0xFFA00000, L1_IMEMORY},
+			{0x00000000, SDRAM_IKERNEL},	/*SDRAM_Page1*/
+			{0x00400000, SDRAM_IKERNEL},	/*SDRAM_Page1*/
+			{0x07C00000, SDRAM_IKERNEL},    /*SDRAM_Page14*/
+			{0x00800000, SDRAM_IGENERIC},	/*SDRAM_Page2*/
+			{0x00C00000, SDRAM_IGENERIC},	/*SDRAM_Page2*/
+			{0x01000000, SDRAM_IGENERIC},	/*SDRAM_Page4*/
+			{0x01400000, SDRAM_IGENERIC},	/*SDRAM_Page5*/
+			{0x01800000, SDRAM_IGENERIC},	/*SDRAM_Page6*/
+			{0x01C00000, SDRAM_IGENERIC},	/*SDRAM_Page7*/
+			{0x02000000, SDRAM_IGENERIC},	/*SDRAM_Page8*/
+			{0x02400000, SDRAM_IGENERIC},	/*SDRAM_Page9*/
+			{0x02800000, SDRAM_IGENERIC},	/*SDRAM_Page10*/
+			{0x02C00000, SDRAM_IGENERIC},	/*SDRAM_Page11*/
+			{0x03000000, SDRAM_IGENERIC},	/*SDRAM_Page12*/
+			{0x03400000, SDRAM_IGENERIC},	/*SDRAM_Page13*/
+};
+
+static unsigned int dcplb_table[16][2]={
+			{0xFFA00000,L1_DMEMORY},
+			{0x00000000,SDRAM_DKERNEL},	/*SDRAM_Page1*/
+			{0x00400000,SDRAM_DKERNEL},	/*SDRAM_Page1*/
+			{0x07C00000,SDRAM_DKERNEL},	/*SDRAM_Page15*/
+			{0x00800000,SDRAM_DGENERIC},	/*SDRAM_Page2*/
+			{0x00C00000,SDRAM_DGENERIC},	/*SDRAM_Page3*/
+			{0x01000000,SDRAM_DGENERIC},	/*SDRAM_Page4*/
+			{0x01400000,SDRAM_DGENERIC},	/*SDRAM_Page5*/
+			{0x01800000,SDRAM_DGENERIC},	/*SDRAM_Page6*/
+			{0x01C00000,SDRAM_DGENERIC},	/*SDRAM_Page7*/
+			{0x02000000,SDRAM_DGENERIC},	/*SDRAM_Page8*/
+			{0x02400000,SDRAM_DGENERIC},	/*SDRAM_Page9*/
+			{0x02800000,SDRAM_DGENERIC},	/*SDRAM_Page10*/
+			{0x02C00000,SDRAM_DGENERIC},	/*SDRAM_Page11*/
+			{0x03000000,SDRAM_DGENERIC},	/*SDRAM_Page12*/
+			{0x20000000,SDRAM_EBIU},	/*For Network */
+};
+
+int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	__asm__ __volatile__
+	("cli r3;"
+	"P0 = %0;"
+	"JUMP (P0);"
+	:
+	: "r" (L1_ISRAM)
+	);
+
+	return 0;
+}
+
+/* These functions are just used to satisfy the linker */
+int cpu_init(void)
+{
+	return 0;
+}
+
+int cleanup_before_linux(void)
+{
+	return 0;
+}
+
+void icache_enable(void)
+{
+	unsigned int *I0,*I1;
+	int i;
+
+	I0 = (unsigned int *)ICPLB_ADDR0;
+	I1 = (unsigned int *)ICPLB_DATA0;
+
+	for(i=0;i<16;i++){
+		*I0++ = icplb_table[i][0];
+		*I1++ = icplb_table[i][1];
+		}
+	cli();
+	SSYNC();
+	*(unsigned int *)IMEM_CONTROL = IMC | ENICPLB;
+	SSYNC();
+	sti();
+}
+
+void icache_disable(void)
+{
+	cli();
+	SSYNC();
+	*(unsigned int *)IMEM_CONTROL &= ~(IMC | ENICPLB);
+	SSYNC();
+	sti();
+}
+
+int icache_status(void)
+{
+	unsigned int value;
+	value = *(unsigned int *)IMEM_CONTROL;
+
+	if( value & (IMC|ENICPLB) )
+		return CACHE_ON;
+	else
+		return CACHE_OFF;
+}
+
+void dcache_enable(void)
+{
+	unsigned int *I0,*I1;
+	unsigned int temp;
+	int i;
+	I0 = (unsigned int *)DCPLB_ADDR0;
+	I1 = (unsigned int *)DCPLB_DATA0;
+
+	for(i=0;i<16;i++){
+		*I0++ = dcplb_table[i][0];
+		*I1++ = dcplb_table[i][1];
+		}
+	cli();
+	temp = *(unsigned int *)DMEM_CONTROL;
+	SSYNC();
+	*(unsigned int *)DMEM_CONTROL = ACACHE_BCACHE |ENDCPLB |PORT_PREF0|temp;
+	SSYNC();
+	sti();
+}
+
+void dcache_disable(void)
+{
+	cli();
+	SSYNC();
+	*(unsigned int *)DMEM_CONTROL &= ~(ACACHE_BCACHE |ENDCPLB |PORT_PREF0);
+	SSYNC();
+	sti();
+}
+
+int dcache_status(void)
+{
+	unsigned int value;
+	value = *(unsigned int *)DMEM_CONTROL;
+	if( value & (ENDCPLB))
+		return CACHE_ON;
+	else
+		return CACHE_OFF;
+}

cpu/bf533/cpu.h

@@ -0,0 +1,65 @@
+/*
+ *  U-boot - cpu.h
+ *
+ *  Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _CPU_H_
+#define _CPU_H_
+
+#include <command.h>
+
+#define INTERNAL_IRQS (32)
+#define NUM_IRQ_NODES 16
+#define DEF_INTERRUPT_FLAGS 1
+#define MAX_TIM_LOAD	0xFFFFFFFF
+
+void blackfin_irq_panic(int reason, struct pt_regs * reg);
+extern void dump(struct pt_regs * regs);
+void display_excp(void);
+asmlinkage void evt_nmi(void);
+asmlinkage void evt_exception(void);
+asmlinkage void trap(void);
+asmlinkage void evt_ivhw(void);
+asmlinkage void evt_rst(void);
+asmlinkage void evt_timer(void);
+asmlinkage void evt_evt7(void);
+asmlinkage void evt_evt8(void);
+asmlinkage void evt_evt9(void);
+asmlinkage void evt_evt10(void);
+asmlinkage void evt_evt11(void);
+asmlinkage void evt_evt12(void);
+asmlinkage void evt_evt13(void);
+asmlinkage void evt_soft_int1(void);
+asmlinkage void evt_system_call(void);
+void blackfin_irq_panic(int reason, struct pt_regs * regs);
+void blackfin_free_irq(unsigned int irq, void *dev_id);
+void call_isr(int irq, struct pt_regs * fp);
+void blackfin_do_irq(int vec, struct pt_regs *fp);
+void blackfin_init_IRQ(void);
+void blackfin_enable_irq(unsigned int irq);
+void blackfin_disable_irq(unsigned int irq);
+extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+int blackfin_request_irq(unsigned int irq,
+		     void (*handler)(int, void *, struct pt_regs *),
+		     unsigned long flags,const char *devname,void *dev_id);
+void timer_init(void);
+#endif

cpu/bf533/flush.S

@@ -0,0 +1,402 @@
+/* Copyright (C) 2003 Analog Devices, Inc. All Rights Reserved.
+ * Copyright (C) 2004 LG SOft India. All Rights Reserved.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.
+ *
+ * Blackfin BF533/2.6 support : LG Soft India
+ */
+#define ASSEMBLY
+
+#include <asm/linkage.h>
+#include <asm/cplb.h>
+#include <asm/blackfin.h>
+
+.text
+
+/* This is an external function being called by the user
+ * application through __flush_cache_all. Currently this function
+ * serves the purpose of flushing all the pending writes in
+ * in the instruction cache.
+ */
+
+ENTRY(flush_instruction_cache)
+	[--SP] = ( R7:6, P5:4 );
+	LINK 12;
+	SP += -12;
+	P5.H = (ICPLB_ADDR0 >> 16);
+	P5.L = (ICPLB_ADDR0 & 0xFFFF);
+	P4.H = (ICPLB_DATA0 >> 16);
+	P4.L = (ICPLB_DATA0 & 0xFFFF);
+	R7 = CPLB_VALID | CPLB_L1_CHBL;
+	R6 = 16;
+inext:	R0 = [P5++];
+	R1 = [P4++];
+	[--SP] =  RETS;
+	CALL icplb_flush;	/* R0 = page, R1 = data*/
+	RETS = [SP++];
+iskip:	R6 += -1;
+	CC = R6;
+	IF CC JUMP inext;
+	SSYNC;
+	SP += 12;
+	UNLINK;
+	( R7:6, P5:4 ) = [SP++];
+	RTS;
+
+/* This is an internal function to flush all pending
+ * writes in the cache associated with a particular ICPLB.
+ *
+ * R0 -  page's start address
+ * R1 -  CPLB's data field.
+ */
+
+.align 2
+ENTRY(icplb_flush)
+	[--SP] = ( R7:0, P5:0 );
+	[--SP] = LC0;
+	[--SP] = LT0;
+	[--SP] = LB0;
+	[--SP] = LC1;
+	[--SP] = LT1;
+	[--SP] = LB1;
+
+	/* If it's a 1K or 4K page, then it's quickest to
+	 * just systematically flush all the addresses in
+	 * the page, regardless of whether they're in the
+	 * cache, or dirty. If it's a 1M or 4M page, there
+	 * are too many addresses, and we have to search the
+	 * cache for lines corresponding to the page.
+	 */
+
+	CC = BITTST(R1, 17);	/* 1MB or 4MB */
+	IF !CC JUMP iflush_whole_page;
+
+	/* We're only interested in the page's size, so extract
+	 * this from the CPLB (bits 17:16), and scale to give an
+	 * offset into the page_size and page_prefix tables.
+	 */
+
+	R1 <<= 14;
+	R1 >>= 30;
+	R1 <<= 2;
+
+	/* We can also determine the sub-bank used, because this is
+	 * taken from bits 13:12 of the address.
+	 */
+
+	R3 = ((12<<8)|2);		/* Extraction pattern */
+	nop;				/*Anamoly 05000209*/
+	R4 = EXTRACT(R0, R3.L) (Z);	/* Extract bits*/
+	R3.H = R4.L << 0 ;		/* Save in extraction pattern for later deposit.*/
+
+
+	/* So:
+	 * R0 = Page start
+	 * R1 = Page length (actually, offset into size/prefix tables)
+	 * R3 = sub-bank deposit values
+  	 *
+	 * The cache has 2 Ways, and 64 sets, so we iterate through
+	 * the sets, accessing the tag for each Way, for our Bank and
+	 * sub-bank, looking for dirty, valid tags that match our
+	 * address prefix.
+	 */
+
+	P5.L = (ITEST_COMMAND & 0xFFFF);
+	P5.H = (ITEST_COMMAND >> 16);
+	P4.L = (ITEST_DATA0 & 0xFFFF);
+	P4.H = (ITEST_DATA0 >> 16);
+
+	P0.L = page_prefix_table;
+	P0.H = page_prefix_table;
+	P1 = R1;
+	R5 = 0;			/* Set counter*/
+	P0 = P1 + P0;
+	R4 = [P0];		/* This is the address prefix*/
+
+	/* We're reading (bit 1==0) the tag (bit 2==0), and we
+	 * don't care about which double-word, since we're only
+	 * fetching tags, so we only have to set Set, Bank,
+	 * Sub-bank and Way.
+	 */
+
+	P2 = 4;
+	LSETUP (ifs1, ife1) LC1 = P2;
+ifs1:	P0 = 32;		/* iterate over all sets*/
+	LSETUP (ifs0, ife0) LC0 = P0;
+ifs0:	R6 = R5 << 5;		/* Combine set*/
+	R6.H = R3.H << 0 ;	/* and sub-bank*/
+	[P5] = R6;		/* Issue Command*/
+	SSYNC;			/* CSYNC will not work here :(*/
+	R7 = [P4];		/* and read Tag.*/
+	CC = BITTST(R7, 0);	/* Check if valid*/
+	IF !CC JUMP ifskip;	/* and skip if not.*/
+
+	/* Compare against the page address. First, plant bits 13:12
+	 * into the tag, since those aren't part of the returned data.
+	 */
+
+	R7 = DEPOSIT(R7, R3);	/* set 13:12*/
+	R1 = R7 & R4;		/* Mask off lower bits*/
+	CC = R1 == R0;		/* Compare against page start.*/
+	IF !CC JUMP ifskip;	/* Skip it if it doesn't match.*/
+
+	/* Tag address matches against page, so this is an entry
+	 * we must flush.
+	 */
+
+	R7 >>= 10;		/* Mask off the non-address bits*/
+	R7 <<= 10;
+	P3 = R7;
+	IFLUSH [P3];		/* And flush the entry*/
+ifskip:
+ife0:	R5 += 1;		/* Advance to next Set*/
+ife1:	NOP;
+
+ifinished:
+	SSYNC;			/* Ensure the data gets out to mem.*/
+
+	/*Finished. Restore context.*/
+	LB1 = [SP++];
+	LT1 = [SP++];
+	LC1 = [SP++];
+	LB0 = [SP++];
+	LT0 = [SP++];
+	LC0 = [SP++];
+	( R7:0, P5:0 ) = [SP++];
+	RTS;
+
+iflush_whole_page:
+	/* It's a 1K or 4K page, so quicker to just flush the
+	 * entire page.
+	 */
+
+	P1 = 32;		/* For 1K pages*/
+	P2 = P1 << 2;		/* For 4K pages*/
+	P0 = R0;		/* Start of page*/
+	CC = BITTST(R1, 16);	/* Whether 1K or 4K*/
+	IF CC P1 = P2;
+	P1 += -1;		/* Unroll one iteration*/
+	SSYNC;
+	IFLUSH [P0++];		/* because CSYNC can't end loops.*/
+	LSETUP (isall, ieall) LC0 = P1;
+isall:IFLUSH [P0++];
+ieall: NOP;
+	SSYNC;
+	JUMP ifinished;
+
+/* This is an external function being called by the user
+ * application through __flush_cache_all. Currently this function
+ * serves the purpose of flushing all the pending writes in
+ * in the data cache.
+ */
+
+ENTRY(flush_data_cache)
+	[--SP] = ( R7:6, P5:4 );
+	LINK 12;
+	SP += -12;
+	P5.H = (DCPLB_ADDR0 >> 16);
+	P5.L = (DCPLB_ADDR0 & 0xFFFF);
+	P4.H = (DCPLB_DATA0 >> 16);
+	P4.L = (DCPLB_DATA0 & 0xFFFF);
+	R7 = CPLB_VALID | CPLB_L1_CHBL | CPLB_DIRTY (Z);
+	R6 = 16;
+next:	R0 = [P5++];
+	R1 = [P4++];
+	CC = BITTST(R1, 14);	/* Is it write-through?*/
+	IF CC JUMP skip;	/* If so, ignore it.*/
+	R2 = R1 & R7;		/* Is it a dirty, cached page?*/
+	CC = R2;
+	IF !CC JUMP skip;	/* If not, ignore it.*/
+	[--SP] = RETS;
+	CALL dcplb_flush;	/* R0 = page, R1 = data*/
+	RETS = [SP++];
+skip:	R6 += -1;
+	CC = R6;
+	IF CC JUMP next;
+	SSYNC;
+	SP += 12;
+	UNLINK;
+	( R7:6, P5:4 ) = [SP++];
+	RTS;
+
+/* This is an internal function to flush all pending
+ * writes in the cache associated with a particular DCPLB.
+ *
+ * R0 -  page's start address
+ * R1 -  CPLB's data field.
+ */
+
+.align 2
+ENTRY(dcplb_flush)
+	[--SP] = ( R7:0, P5:0 );
+	[--SP] = LC0;
+	[--SP] = LT0;
+	[--SP] = LB0;
+	[--SP] = LC1;
+	[--SP] = LT1;
+	[--SP] = LB1;
+
+	/* If it's a 1K or 4K page, then it's quickest to
+	 * just systematically flush all the addresses in
+	 * the page, regardless of whether they're in the
+	 * cache, or dirty. If it's a 1M or 4M page, there
+	 * are too many addresses, and we have to search the
+	 * cache for lines corresponding to the page.
+	 */
+
+	CC = BITTST(R1, 17);	/* 1MB or 4MB */
+	IF !CC JUMP dflush_whole_page;
+
+	/* We're only interested in the page's size, so extract
+	 * this from the CPLB (bits 17:16), and scale to give an
+	 * offset into the page_size and page_prefix tables.
+	 */
+
+	R1 <<= 14;
+	R1 >>= 30;
+	R1 <<= 2;
+
+	/* The page could be mapped into Bank A or Bank B, depending
+	 * on (a) whether both banks are configured as cache, and
+	 * (b) on whether address bit A[x] is set. x is determined
+	 * by DCBS in DMEM_CONTROL
+	 */
+
+	R2 = 0;			/* Default to Bank A (Bank B would be 1)*/
+
+	P0.L = (DMEM_CONTROL & 0xFFFF);
+	P0.H = (DMEM_CONTROL >> 16);
+
+	R3 = [P0];		/* If Bank B is not enabled as cache*/
+	CC = BITTST(R3, 2);	/* then Bank A is our only option.*/
+	IF CC JUMP bank_chosen;
+
+	R4 = 1<<14;		/* If DCBS==0, use A[14].*/
+	R5 = R4 << 7;		/* If DCBS==1, use A[23];*/
+	CC = BITTST(R3, 4);
+	IF CC R4 = R5;		/* R4 now has either bit 14 or bit 23 set.*/
+	R5 = R0 & R4;		/* Use it to test the Page address*/
+	CC = R5;		/* and if that bit is set, we use Bank B,*/
+	R2 = CC;		/* else we use Bank A.*/
+	R2 <<= 23;		/* The Bank selection's at posn 23.*/
+
+bank_chosen:
+
+	/* We can also determine the sub-bank used, because this is
+	 * taken from bits 13:12 of the address.
+	 */
+
+	R3 = ((12<<8)|2);		/* Extraction pattern */
+	nop;				/*Anamoly 05000209*/
+	R4 = EXTRACT(R0, R3.L) (Z);	/* Extract bits*/
+	R3.H = R4.L << 0 ;		/* Save in extraction pattern for later deposit.*/
+
+	/* So:
+	 * R0 = Page start
+	 * R1 = Page length (actually, offset into size/prefix tables)
+	 * R2 = Bank select mask
+	 * R3 = sub-bank deposit values
+  	 *
+	 * The cache has 2 Ways, and 64 sets, so we iterate through
+	 * the sets, accessing the tag for each Way, for our Bank and
+	 * sub-bank, looking for dirty, valid tags that match our
+	 * address prefix.
+	 */
+
+	P5.L = (DTEST_COMMAND & 0xFFFF);
+	P5.H = (DTEST_COMMAND >> 16);
+	P4.L = (DTEST_DATA0 & 0xFFFF);
+	P4.H = (DTEST_DATA0 >> 16);
+
+	P0.L = page_prefix_table;
+	P0.H = page_prefix_table;
+	P1 = R1;
+	R5 = 0;			/* Set counter*/
+	P0 = P1 + P0;
+	R4 = [P0];		/* This is the address prefix*/
+
+
+	/* We're reading (bit 1==0) the tag (bit 2==0), and we
+	 * don't care about which double-word, since we're only
+	 * fetching tags, so we only have to set Set, Bank,
+	 * Sub-bank and Way.
+	 */
+
+	P2 = 2;
+	LSETUP (fs1, fe1) LC1 = P2;
+fs1:	P0 = 64;		/* iterate over all sets*/
+	LSETUP (fs0, fe0) LC0 = P0;
+fs0:	R6 = R5 << 5;		/* Combine set*/
+	R6.H = R3.H << 0 ;	/* and sub-bank*/
+	R6 = R6 | R2;		/* and Bank. Leave Way==0 at first.*/
+	BITSET(R6,14);
+	[P5] = R6;		/* Issue Command*/
+	SSYNC;
+	R7 = [P4];		/* and read Tag.*/
+	CC = BITTST(R7, 0);	/* Check if valid*/
+	IF !CC JUMP fskip;	/* and skip if not.*/
+	CC = BITTST(R7, 1);	/* Check if dirty*/
+	IF !CC JUMP fskip;	/* and skip if not.*/
+
+	/* Compare against the page address. First, plant bits 13:12
+	 * into the tag, since those aren't part of the returned data.
+	 */
+
+	R7 = DEPOSIT(R7, R3);	/* set 13:12*/
+	R1 = R7 & R4;		/* Mask off lower bits*/
+	CC = R1 == R0;		/* Compare against page start.*/
+	IF !CC JUMP fskip;	/* Skip it if it doesn't match.*/
+
+	/* Tag address matches against page, so this is an entry
+	 * we must flush.
+	 */
+
+	R7 >>= 10;		/* Mask off the non-address bits*/
+	R7 <<= 10;
+	P3 = R7;
+	SSYNC;
+	FLUSHINV [P3];		/* And flush the entry*/
+fskip:
+fe0:	R5 += 1;		/* Advance to next Set*/
+fe1:	BITSET(R2, 26);		/* Go to next Way.*/
+
+dfinished:
+	SSYNC;			/* Ensure the data gets out to mem.*/
+
+	/*Finished. Restore context.*/
+	LB1 = [SP++];
+	LT1 = [SP++];
+	LC1 = [SP++];
+	LB0 = [SP++];
+	LT0 = [SP++];
+	LC0 = [SP++];
+	( R7:0, P5:0 ) = [SP++];
+	RTS;
+
+dflush_whole_page:
+
+	/* It's a 1K or 4K page, so quicker to just flush the
+	 * entire page.
+	 */
+
+	P1 = 32;		/* For 1K pages*/
+	P2 = P1 << 2;		/* For 4K pages*/
+	P0 = R0;		/* Start of page*/
+	CC = BITTST(R1, 16);	/* Whether 1K or 4K*/
+	IF CC P1 = P2;
+	P1 += -1;		/* Unroll one iteration*/
+    SSYNC;
+	FLUSHINV [P0++];	/* because CSYNC can't end loops.*/
+	LSETUP (eall, eall) LC0 = P1;
+eall:	FLUSHINV [P0++];
+	SSYNC;
+	JUMP dfinished;
+
+.align 4;
+page_prefix_table:
+.byte4 	0xFFFFFC00;	/* 1K */
+.byte4	0xFFFFF000;	/* 4K */
+.byte4	0xFFF00000;	/* 1M */
+.byte4	0xFFC00000;	/* 4M */
+.page_prefix_table.end:

cpu/bf533/interrupt.S

@@ -0,0 +1,391 @@
+/*
+ * U-boot - interrupt.S Processing of interrupts and exception handling
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * This file is based on interrupt.S
+ *
+ * Copyright (C) 2003  Metrowerks, Inc. <mwaddel@metrowerks.com>
+ * Copyright (C) 2002  Arcturus Networks Ltd. Ted Ma <mated@sympatico.ca>
+ * Copyright (C) 1998  D. Jeff Dionne <jeff@ryeham.ee.ryerson.ca>,
+ *                     Kenneth Albanowski <kjahds@kjahds.com>,
+ *                     The Silver Hammer Group, Ltd.
+ *
+ * (c) 1995, Dionne & Associates
+ * (c) 1995, DKG Display Tech.
+ *
+ * This file is also based on exception.asm
+ * (C) Copyright 2001-2005 - Analog Devices, Inc.  All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define ASSEMBLY
+
+#include <asm/hw_irq.h>
+#include <asm/entry.h>
+#include <asm/blackfin_defs.h>
+#include <asm/cpu/bf533_irq.h>
+
+.global blackfin_irq_panic;
+
+.text
+.align 2
+
+#ifndef CONFIG_KGDB
+.global evt_emulation
+evt_emulation:
+	SAVE_CONTEXT
+	r0 = IRQ_EMU;
+	r1 = seqstat;
+	sp += -12;
+	call blackfin_irq_panic;
+	sp += 12;
+	rte;
+#endif
+
+.global evt_nmi
+evt_nmi:
+	SAVE_CONTEXT
+	r0 = IRQ_NMI;
+	r1 = RETN;
+	sp += -12;
+	call blackfin_irq_panic;
+	sp += 12;
+
+_evt_nmi_exit:
+	rtn;
+
+.global trap
+trap:
+	[--sp] = r0;
+	[--sp] = r1;
+	[--sp] = p0;
+	[--sp] = p1;
+	[--sp] = astat;
+	r0 = seqstat;
+	R0 <<= 26;
+	R0 >>= 26;
+	p0 = r0;
+	p1.l = EVTABLE;
+	p1.h = EVTABLE;
+	p0 = p1 + (p0 << 1);
+	r1 = W[p0] (Z);
+	p1 = r1;
+	jump (pc + p1);
+
+.global _EVENT1
+_EVENT1:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT2
+_EVENT2:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT3
+_EVENT3:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT4
+_EVENT4:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT5
+_EVENT5:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT6
+_EVENT6:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT7
+_EVENT7:
+	RAISE 15;
+	JUMP.S _EXIT;
+
+.global _EVENT8
+_EVENT8:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT9
+_EVENT9:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT10
+_EVENT10:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT11
+_EVENT11:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT12
+_EVENT12:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT13
+_EVENT13:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT14
+_EVENT14:
+/*	RAISE 14;	*/
+	CALL	_cplb_hdr;
+	JUMP.S _EXIT;
+
+.global _EVENT19
+_EVENT19:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT20
+_EVENT20:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EVENT21
+_EVENT21:
+	RAISE 14;
+	JUMP.S _EXIT;
+
+.global _EXIT
+_EXIT:
+	ASTAT = [sp++];
+	p1 = [sp++];
+	p0 = [sp++];
+	r1 = [sp++];
+	r0 = [sp++];
+	RTX;
+
+EVTABLE:
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x0000;
+	.byte2 0x003E;
+	.byte2 0x0042;
+	.byte4 0x0000;
+	.byte4 0x0000;
+	.byte4 0x0000;
+	.byte4 0x0000;
+	.byte4 0x0000;
+	.byte4 0x0000;
+	.byte4 0x0000;
+	.byte2 0x0000;
+	.byte2 0x001E;
+	.byte2 0x0022;
+	.byte2 0x0032;
+	.byte2 0x002e;
+	.byte2 0x0002;
+	.byte2 0x0036;
+	.byte2 0x002A;
+	.byte2 0x001A;
+	.byte2 0x0016;
+	.byte2 0x000A;
+	.byte2 0x000E;
+	.byte2 0x0012;
+	.byte2 0x0006;
+	.byte2 0x0026;
+
+.global evt_rst
+evt_rst:
+	SAVE_CONTEXT
+	r0 = IRQ_RST;
+	r1 = RETN;
+	sp += -12;
+	call do_reset;
+	sp += 12;
+
+_evt_rst_exit:
+	rtn;
+
+irq_panic:
+	r0 = IRQ_EVX;
+	r1 =  sp;
+	sp += -12;
+	call blackfin_irq_panic;
+	sp += 12;
+
+.global evt_ivhw
+evt_ivhw:
+	SAVE_CONTEXT
+	RAISE 14;
+
+_evt_ivhw_exit:
+	 rti;
+
+.global evt_timer
+evt_timer:
+	SAVE_CONTEXT
+	r0 = IRQ_CORETMR;
+	sp += -12;
+	/* Polling method used now. */
+	/* call timer_int; */
+	sp += 12;
+	RESTORE_CONTEXT
+	rti;
+	nop;
+
+.global evt_evt7
+evt_evt7:
+	SAVE_CONTEXT
+	r0 = 7;
+	sp += -12;
+	call process_int;
+	sp += 12;
+
+evt_evt7_exit:
+	RESTORE_CONTEXT
+	rti;
+
+.global evt_evt8
+evt_evt8:
+	SAVE_CONTEXT
+	r0 = 8;
+	sp += -12;
+	call process_int;
+	sp += 12;
+
+evt_evt8_exit:
+	RESTORE_CONTEXT
+	rti;
+
+.global evt_evt9
+evt_evt9:
+	SAVE_CONTEXT
+	r0 = 9;
+	sp += -12;
+	call process_int;
+	sp += 12;
+
+evt_evt9_exit:
+	RESTORE_CONTEXT
+	rti;
+
+.global evt_evt10
+evt_evt10:
+	SAVE_CONTEXT
+	r0 = 10;
+	sp += -12;
+	call process_int;
+	sp += 12;
+
+evt_evt10_exit:
+	RESTORE_CONTEXT
+	rti;
+
+.global evt_evt11
+evt_evt11:
+	SAVE_CONTEXT
+	r0 = 11;
+	sp += -12;
+	call process_int;
+	sp += 12;
+
+evt_evt11_exit:
+	RESTORE_CONTEXT
+	rti;
+
+.global evt_evt12
+evt_evt12:
+	SAVE_CONTEXT
+	r0 = 12;
+	sp += -12;
+	call process_int;
+	sp += 12;
+evt_evt12_exit:
+	 RESTORE_CONTEXT
+	 rti;
+
+.global evt_evt13
+evt_evt13:
+	SAVE_CONTEXT
+	r0 = 13;
+	sp += -12;
+	call process_int;
+	sp += 12;
+
+evt_evt13_exit:
+	 RESTORE_CONTEXT
+	 rti;
+
+.global evt_system_call
+evt_system_call:
+	[--sp] = r0;
+	[--SP] = RETI;
+	r0 = [sp++];
+	r0 += 2;
+	[--sp] = r0;
+	RETI = [SP++];
+	r0 = [SP++];
+	SAVE_CONTEXT
+	sp += -12;
+	call display_excp;
+	sp += 12;
+	RESTORE_CONTEXT
+	RTI;
+
+evt_system_call_exit:
+	rti;
+
+.global evt_soft_int1
+evt_soft_int1:
+	[--sp] = r0;
+	[--SP] = RETI;
+	r0 = [sp++];
+	r0 += 2;
+	[--sp] = r0;
+	RETI = [SP++];
+	r0 = [SP++];
+	SAVE_CONTEXT
+	sp += -12;
+	call display_excp;
+	sp += 12;
+	RESTORE_CONTEXT
+	RTI;
+
+evt_soft_int1_exit:
+	rti;

cpu/bf533/interrupts.c

@@ -0,0 +1,165 @@
+/*
+ * U-boot - interrupts.c Interrupt related routines
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * This file is based on interrupts.c
+ * Copyright 1996 Roman Zippel
+ * Copyright 1999 D. Jeff Dionne <jeff@uclinux.org>
+ * Copyright 2000-2001 Lineo, Inc. D. Jefff Dionne <jeff@lineo.ca>
+ * Copyright 2002 Arcturus Networks Inc. MaTed <mated@sympatico.ca>
+ * Copyright 2003 Metrowerks/Motorola
+ * Copyright 2003 Bas Vermeulen <bas@buyways.nl>,
+ * 			BuyWays B.V. (www.buyways.nl)
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/machdep.h>
+#include <asm/irq.h>
+#include <asm/cpu/defBF533.h>
+#include "cpu.h"
+
+static ulong timestamp;
+static ulong last_time;
+static int int_flag;
+
+int irq_flags; /* needed by asm-blackfin/system.h */
+
+/* Functions just to satisfy the linker */
+
+/*
+ * This function is derived from PowerPC code (read timebase as long long).
+ * On BF533 it just returns the timer value.
+ */
+unsigned long long get_ticks(void)
+{
+	return get_timer(0);
+}
+
+/*
+ * This function is derived from PowerPC code (timebase clock frequency).
+ * On BF533 it returns the number of timer ticks per second.
+ */
+ulong get_tbclk (void)
+{
+	ulong tbclk;
+
+	tbclk = CFG_HZ;
+	return tbclk;
+}
+
+void enable_interrupts(void)
+{
+	restore_flags(int_flag);
+}
+
+int disable_interrupts(void)
+{
+	save_and_cli(int_flag);
+	return 1;
+}
+
+int interrupt_init(void)
+{
+	return (0);
+}
+
+void udelay(unsigned long usec)
+{
+	unsigned long delay, start, stop;
+	unsigned long cclk;
+	cclk = (CONFIG_CCLK_HZ);
+
+	while ( usec > 1 ) {
+	       /*
+		* how many clock ticks to delay?
+		*  - request(in useconds) * clock_ticks(Hz) / useconds/second
+		*/
+		if (usec < 1000) {
+			delay = (usec * (cclk/244)) >> 12 ;
+			usec = 0;
+		} else {
+			delay = (1000 * (cclk/244)) >> 12 ;
+			usec -= 1000;
+		}
+
+		asm volatile (" %0 = CYCLES;": "=g"(start));
+		do {
+			asm volatile (" %0 = CYCLES; ": "=g"(stop));
+		} while (stop - start < delay);
+	}
+
+	return;
+}
+
+void timer_init(void)
+{
+	*pTCNTL = 0x1;
+	*pTSCALE = 0x0;
+	*pTCOUNT  = MAX_TIM_LOAD;
+	*pTPERIOD = MAX_TIM_LOAD;
+	*pTCNTL = 0x7;
+	asm("CSYNC;");
+
+	timestamp = 0;
+	last_time = 0;
+}
+
+/* Any network command or flash
+ * command is started get_timer shall
+ * be called before TCOUNT gets reset,
+ * to implement the accurate timeouts.
+ *
+ * How ever milliconds doesn't return
+ * the number that has been elapsed from
+ * the last reset.
+ *
+ *  As get_timer is used in the u-boot
+ *  only for timeouts this should be
+ *  sufficient
+ */
+ulong get_timer(ulong base)
+{
+	ulong milisec;
+
+	/* Number of clocks elapsed */
+	ulong clocks = (MAX_TIM_LOAD - (*pTCOUNT));
+
+	/* Find if the TCOUNT is reset
+	timestamp gives the number of times
+	TCOUNT got reset */
+	if(clocks < last_time)
+		timestamp++;
+	last_time = clocks;
+
+	/* Get the number of milliseconds */
+	milisec = clocks/(CONFIG_CCLK_HZ / 1000);
+
+	/* Find the number of millisonds
+	that got elapsed before this TCOUNT
+	cycle */
+	milisec += timestamp * (MAX_TIM_LOAD/(CONFIG_CCLK_HZ / 1000));
+
+	return (milisec - base);
+}

cpu/bf533/ints.c

@@ -0,0 +1,107 @@
+/*
+ * U-boot - ints.c Interrupt related routines
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * This file is based on ints.c
+ *
+ * Apr18 2003, Changed by HuTao to support interrupt cascading for Blackfin
+ *             drivers
+ *
+ * Copyright 1996 Roman Zippel
+ * Copyright 1999 D. Jeff Dionne <jeff@uclinux.org>
+ * Copyright 2000-2001 Lineo, Inc. D. Jefff Dionne <jeff@lineo.ca>
+ * Copyright 2002 Arcturus Networks Inc. MaTed <mated@sympatico.ca>
+ * Copyright 2003 Metrowerks/Motorola
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/stddef.h>
+#include <asm/system.h>
+#include <asm/irq.h>
+#include <asm/traps.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/machdep.h>
+#include <asm/setup.h>
+#include <asm/blackfin.h>
+#include "cpu.h"
+
+void blackfin_irq_panic(int reason, struct pt_regs *regs)
+{
+	printf("\n\nException: IRQ 0x%x entered\n", reason);
+	printf("code=[0x%x], ", (unsigned int) (regs->seqstat & 0x3f));
+	printf("stack frame=0x%x, ", (unsigned int) regs);
+	printf("bad PC=0x%04x\n", (unsigned int) regs->pc);
+	dump(regs);
+	printf("Unhandled IRQ or exceptions!\n");
+	printf("Please reset the board \n");
+}
+
+void blackfin_init_IRQ(void)
+{
+	*(unsigned volatile long *) (SIC_IMASK) = SIC_UNMASK_ALL;
+	cli();
+#ifndef CONFIG_KGDB
+	*(unsigned volatile long *) (EVT_EMULATION_ADDR) = 0x0;
+#endif
+	*(unsigned volatile long *) (EVT_NMI_ADDR) =
+		(unsigned volatile long) evt_nmi;
+	*(unsigned volatile long *) (EVT_EXCEPTION_ADDR) =
+		(unsigned volatile long) trap;
+	*(unsigned volatile long *) (EVT_HARDWARE_ERROR_ADDR) =
+		(unsigned volatile long) evt_ivhw;
+	*(unsigned volatile long *) (EVT_RESET_ADDR) =
+		(unsigned volatile long) evt_rst;
+	*(unsigned volatile long *) (EVT_TIMER_ADDR) =
+		(unsigned volatile long) evt_timer;
+	*(unsigned volatile long *) (EVT_IVG7_ADDR) =
+		(unsigned volatile long) evt_evt7;
+	*(unsigned volatile long *) (EVT_IVG8_ADDR) =
+		(unsigned volatile long) evt_evt8;
+	*(unsigned volatile long *) (EVT_IVG9_ADDR) =
+		(unsigned volatile long) evt_evt9;
+	*(unsigned volatile long *) (EVT_IVG10_ADDR) =
+		(unsigned volatile long) evt_evt10;
+	*(unsigned volatile long *) (EVT_IVG11_ADDR) =
+		(unsigned volatile long) evt_evt11;
+	*(unsigned volatile long *) (EVT_IVG12_ADDR) =
+		(unsigned volatile long) evt_evt12;
+	*(unsigned volatile long *) (EVT_IVG13_ADDR) =
+		(unsigned volatile long) evt_evt13;
+	*(unsigned volatile long *) (EVT_IVG14_ADDR) =
+		(unsigned volatile long) evt_system_call;
+	*(unsigned volatile long *) (EVT_IVG15_ADDR) =
+		(unsigned volatile long) evt_soft_int1;
+	*(volatile unsigned long *) ILAT = 0;
+	asm("csync;");
+	sti();
+	*(volatile unsigned long *) IMASK = 0xffbf;
+	asm("csync;");
+}
+
+void display_excp(void)
+{
+	printf("Exception!\n");
+}

cpu/bf533/serial.c

@@ -0,0 +1,194 @@
+/*
+ * U-boot - serial.c Serial driver for BF533
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * This file is based on
+ * bf533_serial.c: Serial driver for BlackFin BF533 DSP internal UART.
+ * Copyright (c) 2003	Bas Vermeulen <bas@buyways.nl>,
+ * 			BuyWays B.V. (www.buyways.nl)
+ *
+ * Based heavily on blkfinserial.c
+ * blkfinserial.c: Serial driver for BlackFin DSP internal USRTs.
+ * Copyright(c) 2003	Metrowerks	<mwaddel@metrowerks.com>
+ * Copyright(c)	2001	Tony Z. Kou	<tonyko@arcturusnetworks.com>
+ * Copyright(c)	2001-2002 Arcturus Networks Inc. <www.arcturusnetworks.com>
+ *
+ * Based on code from 68328 version serial driver imlpementation which was:
+ * Copyright (C) 1995       David S. Miller    <davem@caip.rutgers.edu>
+ * Copyright (C) 1998       Kenneth Albanowski <kjahds@kjahds.com>
+ * Copyright (C) 1998, 1999 D. Jeff Dionne     <jeff@uclinux.org>
+ * Copyright (C) 1999       Vladimir Gurevich  <vgurevic@cisco.com>
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/irq.h>
+#include <asm/system.h>
+#include <asm/segment.h>
+#include <asm/bitops.h>
+#include <asm/delay.h>
+#include <asm/uaccess.h>
+#include "bf533_serial.h"
+
+unsigned long pll_div_fact;
+
+void calc_baud(void)
+{
+	unsigned char i;
+	int	temp;
+
+	for(i = 0; i < sizeof(baud_table)/sizeof(int); i++) {
+		temp =  CONFIG_SCLK_HZ/(baud_table[i]*8);
+		if ( temp && 0x1 == 1 ) {
+			temp++;
+		}
+		temp = temp/2;
+		hw_baud_table[i].dl_high = (temp >> 8)& 0xFF;
+		hw_baud_table[i].dl_low = (temp) & 0xFF;
+	}
+}
+
+void serial_setbrg(void)
+{
+	int i;
+	DECLARE_GLOBAL_DATA_PTR;
+
+	calc_baud();
+
+	for (i = 0; i < sizeof(baud_table) / sizeof(int); i++) {
+		if (gd->baudrate == baud_table[i])
+			break;
+	}
+
+	/* Enable UART */
+	*pUART_GCTL |= UART_GCTL_UCEN;
+	asm("ssync;");
+
+	/* Set DLAB in LCR to Access DLL and DLH */
+	ACCESS_LATCH;
+	asm("ssync;");
+
+	*pUART_DLL = hw_baud_table[i].dl_low;
+	asm("ssync;");
+	*pUART_DLH = hw_baud_table[i].dl_high;
+	asm("ssync;");
+
+	/* Clear DLAB in LCR to Access THR RBR IER */
+	ACCESS_PORT_IER;
+	asm("ssync;");
+
+	/* Enable  ERBFI and ELSI interrupts
+	* to poll SIC_ISR register*/
+	*pUART_IER = UART_IER_ELSI | UART_IER_ERBFI | UART_IER_ETBEI;
+	asm("ssync;");
+
+	/* Set LCR to Word Lengh 8-bit word select */
+	*pUART_LCR = UART_LCR_WLS8;
+	asm("ssync;");
+
+	return;
+}
+
+int serial_init(void)
+{
+	serial_setbrg();
+	return (0);
+}
+
+void serial_putc(const char c)
+{
+	if ((*pUART_LSR) & UART_LSR_TEMT)
+	{
+		if (c == '\n')
+			serial_putc('\r');
+
+		local_put_char(c);
+	}
+
+	while (!((*pUART_LSR) & UART_LSR_TEMT))
+		SYNC_ALL;
+
+	return;
+}
+
+int serial_tstc(void)
+{
+	if (*pUART_LSR & UART_LSR_DR)
+		return 1;
+	else
+		return 0;
+}
+
+int serial_getc(void)
+{
+	unsigned short uart_lsr_val, uart_rbr_val;
+	unsigned long isr_val;
+	int ret;
+
+	/* Poll for RX Interrupt */
+	while (!((isr_val = *(volatile unsigned long *)SIC_ISR) & IRQ_UART_RX_BIT));
+	asm("csync;");
+
+	uart_lsr_val = *pUART_LSR;	/* Clear status bit */
+	uart_rbr_val = *pUART_RBR;	/* getc() */
+
+	if (isr_val & IRQ_UART_ERROR_BIT) {
+		ret =  -1;
+	}
+	else
+	{
+		ret = uart_rbr_val & 0xff;
+	}
+
+	return ret;
+}
+
+void serial_puts(const char *s)
+{
+	while (*s) {
+		serial_putc(*s++);
+	}
+}
+
+static void local_put_char(char ch)
+{
+	int flags = 0;
+	unsigned long isr_val;
+
+	save_and_cli(flags);
+
+	/* Poll for TX Interruput */
+	while (!((isr_val = *pSIC_ISR) & IRQ_UART_TX_BIT));
+	asm("csync;");
+
+	*pUART_THR = ch;			/* putc() */
+
+	if (isr_val & IRQ_UART_ERROR_BIT) {
+		printf("?");
+	}
+
+	restore_flags(flags);
+
+	return ;
+}

cpu/bf533/start.S

@@ -0,0 +1,435 @@
+/*
+ * U-boot - start.S Startup file of u-boot for BF533
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * This file is based on head.S
+ * Copyright (c) 2003  Metrowerks/Motorola
+ * Copyright (C) 1998  D. Jeff Dionne <jeff@ryeham.ee.ryerson.ca>,
+ *                     Kenneth Albanowski <kjahds@kjahds.com>,
+ *                     The Silver Hammer Group, Ltd.
+ * (c) 1995, Dionne & Associates
+ * (c) 1995, DKG Display Tech.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Note: A change in this file subsequently requires a change in
+ *       board/$(board_name)/config.mk for a valid u-boot.bin
+ */
+
+#define ASSEMBLY
+
+#include <linux/config.h>
+#include <asm/blackfin.h>
+#include <config.h>
+#include <asm/mem_init.h>
+
+#if (CONFIG_CCLK_DIV == 1)
+#define CONFIG_CCLK_ACT_DIV   CCLK_DIV1
+#endif
+#if (CONFIG_CCLK_DIV == 2)
+#define CONFIG_CCLK_ACT_DIV   CCLK_DIV2
+#endif
+#if (CONFIG_CCLK_DIV == 4)
+#define CONFIG_CCLK_ACT_DIV   CCLK_DIV4
+#endif
+#if (CONFIG_CCLK_DIV == 8)
+#define CONFIG_CCLK_ACT_DIV   CCLK_DIV8
+#endif
+#ifndef CONFIG_CCLK_ACT_DIV
+#define CONFIG_CCLK_ACT_DIV   CONFIG_CCLK_DIV_not_defined_properly
+#endif
+
+.global _stext;
+.global __bss_start;
+.global start;
+.global _start;
+.global _rambase;
+.global _ramstart;
+.global _ramend;
+.global _bf533_data_dest;
+.global _bf533_data_size;
+.global edata;
+.global _initialize;
+.global _exit;
+.global flashdataend;
+
+.text
+_start:
+start:
+_stext:
+
+	R0 = 0x30;
+	SYSCFG = R0;
+	SSYNC;
+
+	/* As per HW reference manual DAG registers,
+	 * DATA and Address resgister shall be zero'd
+	 * in initialization, after a reset state
+	 */
+	r1 = 0;	/* Data registers zero'd */
+	r2 = 0;
+	r3 = 0;
+	r4 = 0;
+	r5 = 0;
+	r6 = 0;
+	r7 = 0;
+
+	p0 = 0; /* Address registers zero'd */
+	p1 = 0;
+	p2 = 0;
+	p3 = 0;
+	p4 = 0;
+	p5 = 0;
+
+	i0 = 0; /* DAG Registers zero'd */
+	i1 = 0;
+	i2 = 0;
+	i3 = 0;
+	m0 = 0;
+	m1 = 0;
+	m3 = 0;
+	m3 = 0;
+	l0 = 0;
+	l1 = 0;
+	l2 = 0;
+	l3 = 0;
+	b0 = 0;
+	b1 = 0;
+	b2 = 0;
+	b3 = 0;
+
+	/* Set loop counters to zero, to make sure that
+	 * hw loops are disabled.
+	 */
+	lc0 = 0;
+	lc1 = 0;
+
+	SSYNC;
+
+	/* Check soft reset status */
+	p0.h = SWRST >> 16;
+	p0.l = SWRST & 0xFFFF;
+	r0.l = w[p0];
+
+	cc = bittst(r0, 15);
+	if !cc jump no_soft_reset;
+
+	/* Clear Soft reset */
+	r0 = 0x0000;
+	w[p0] = r0;
+	ssync;
+
+no_soft_reset:
+	nop;
+
+	/* Clear EVT registers */
+	p0.h = (EVT_EMULATION_ADDR >> 16);
+	p0.l = (EVT_EMULATION_ADDR & 0xFFFF);
+	p0 += 8;
+	p1 = 14;
+	r1 = 0;
+	LSETUP(4,4) lc0 = p1;
+	[ p0 ++ ] = r1;
+
+	/*
+	 *  Set PLL_CTL
+	 *   - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+	 *   - [8]     = BYPASS    : BYPASS the PLL, run CLKIN into CCLK/SCLK
+	 *   - [7]     = output delay (add 200ps of delay to mem signals)
+	 *   - [6]     = input delay (add 200ps of input delay to mem signals)
+	 *   - [5]     = PDWN      : 1=All Clocks off
+	 *   - [3]     = STOPCK    : 1=Core Clock off
+	 *   - [1]     = PLL_OFF   : 1=Disable Power to PLL
+	 *   - [0]     = DF        : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+	 *   all other bits set to zero
+	 */
+
+	r0 = CONFIG_VCO_MULT;	/* Load the VCO multiplier */
+	r0 = r0 << 9;		/* Shift it over */
+	r1 =  CONFIG_CLKIN_HALF;	/* Do we need to divide CLKIN by 2? */
+	r0 = r1 | r0;
+	r1 = CONFIG_PLL_BYPASS;	/* Bypass the PLL?                 */
+	r1 = r1 << 8;	/* Shift it over */
+	r0 = r1 | r0;	/* add them all together */
+
+	p0.h = (PLL_CTL >> 16);
+	p0.l = (PLL_CTL & 0xFFFF);	/* Load the address */
+	cli r2;				/* Disable interrupts */
+	w[p0] = r0;			/* Set the value */
+	idle;				/* Wait for the PLL to stablize */
+	sti r2;				/* Enable interrupts */
+	ssync;
+
+	/*
+	 * Turn on the CYCLES COUNTER
+	 */
+	r2 = SYSCFG;
+	BITSET (r2,1);
+	SYSCFG = r2;
+
+	/* Configure SCLK & CCLK Dividers */
+	r0 = CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV;
+	p0.h = (PLL_DIV >> 16);
+	p0.l = (PLL_DIV & 0xFFFF);
+	w[p0] = r0;
+	ssync;
+
+wait_for_pll_stab:
+	p0.h = (PLL_STAT >> 16);
+	p0.l = (PLL_STAT & 0xFFFF);
+	r0.l = w[p0];
+	cc = bittst(r0,5);
+	if !cc jump wait_for_pll_stab;
+
+	/* Configure SDRAM if SDRAM is already not enabled */
+	p0.l = (EBIU_SDSTAT & 0xFFFF);
+	p0.h = (EBIU_SDSTAT >> 16);
+	r0.l = w[p0];
+	cc = bittst(r0, 3);
+	if !cc jump skip_sdram_enable;
+
+	/* SDRAM initialization */
+	p0.l = (EBIU_SDGCTL & 0xFFFF);
+	p0.h = (EBIU_SDGCTL >> 16);	/* SDRAM Memory Global Control Register */
+	r0.h = (mem_SDGCTL >> 16);
+	r0.l = (mem_SDGCTL & 0xFFFF);
+	[p0] = r0;
+	ssync;
+
+	p0.l = (EBIU_SDBCTL & 0xFFFF);
+	p0.h = (EBIU_SDBCTL >> 16);	/* SDRAM Memory Bank Control Register */
+	r0 = mem_SDBCTL;
+	w[p0] = r0.l;
+	ssync;
+
+	p0.l = (EBIU_SDRRC & 0xFFFF);
+	p0.h = (EBIU_SDRRC >> 16);	/* SDRAM Refresh Rate Control Register */
+	r0 = mem_SDRRC;
+	w[p0] = r0.l;
+	ssync;
+
+skip_sdram_enable:
+	nop;
+
+#ifndef	CFG_NO_FLASH
+	/* relocate into to RAM */
+	p1.l = (CFG_FLASH_BASE & 0xffff);
+	p1.h = (CFG_FLASH_BASE >> 16);
+	p2.l = (CFG_MONITOR_BASE & 0xffff);
+	p2.h = (CFG_MONITOR_BASE >> 16);
+	r0.l = (CFG_MONITOR_LEN & 0xffff);
+	r0.h = (CFG_MONITOR_LEN >> 16);
+loop1:
+	r1 = [p1];
+	[p2] = r1;
+	p3=0x4;
+	p1=p1+p3;
+	p2=p2+p3;
+	r2=0x4;
+	r0=r0-r2;
+	cc=r0==0x0;
+	if !cc jump loop1;
+#endif
+	/*
+	 * configure STACK
+	 */
+	r0.h = (CONFIG_STACKBASE >> 16);
+	r0.l = (CONFIG_STACKBASE & 0xFFFF);
+	sp = r0;
+	fp = sp;
+
+	/*
+	 * This next section keeps the processor in supervisor mode
+	 * during kernel boot.  Switches to user mode at end of boot.
+	 * See page 3-9 of Hardware Reference manual for documentation.
+	 */
+
+	/* To keep ourselves in the supervisor mode */
+	p0.l = (EVT_IVG15_ADDR & 0xFFFF);
+	p0.h = (EVT_IVG15_ADDR >> 16);
+
+	p1.l = _real_start;
+	p1.h = _real_start;
+	[p0] = p1;
+
+	p0.l = (IMASK & 0xFFFF);
+	p0.h = (IMASK >> 16);
+	r0 = IVG15_POS;
+	[p0] = r0;
+	raise 15;
+	p0.l = WAIT_HERE;
+	p0.h = WAIT_HERE;
+	reti = p0;
+	rti;
+
+WAIT_HERE:
+	jump WAIT_HERE;
+
+.global _real_start;
+_real_start:
+	[ -- sp ] = reti;
+
+#ifdef CONFIG_EZKIT533
+	p0.l = (WDOG_CTL & 0xFFFF);
+	p0.h = (WDOG_CTL >> 16);
+	r0 = WATCHDOG_DISABLE(z);
+	w[p0] = r0;
+#endif
+
+	/* Code for initializing Async mem banks */
+	p2.h = (EBIU_AMBCTL1 >> 16);
+	p2.l = (EBIU_AMBCTL1 & 0xFFFF);
+	r0.h = (AMBCTL1VAL >> 16);
+	r0.l = (AMBCTL1VAL & 0xFFFF);
+	[p2] = r0;
+	ssync;
+
+	p2.h = (EBIU_AMBCTL0 >> 16);
+	p2.l = (EBIU_AMBCTL0 & 0xFFFF);
+	r0.h = (AMBCTL0VAL >> 16);
+	r0.l = (AMBCTL0VAL & 0xFFFF);
+	[p2] = r0;
+	ssync;
+
+	p2.h = (EBIU_AMGCTL >> 16);
+	p2.l = (EBIU_AMGCTL & 0xffff);
+	r0 = AMGCTLVAL;
+	w[p2] = r0;
+	ssync;
+
+	/* DMA reset code to Hi of L1 SRAM */
+copy:
+	P1.H = hi(SYSMMR_BASE);	/* P1 Points to the beginning of SYSTEM MMR Space */
+	P1.L = lo(SYSMMR_BASE);
+
+	R0.H = reset_start;	/* Source Address (high) */
+	R0.L = reset_start;	/* Source Address (low) */
+	R1.H = reset_end;
+	R1.L = reset_end;
+	R2 = R1 - R0;		/* Count */
+	R1.H = hi(L1_ISRAM);	/* Destination Address (high) */
+	R1.L = lo(L1_ISRAM);	/* Destination Address (low) */
+	R3.L = DMAEN;		/* Source DMAConfig Value (8-bit words) */
+	R4.L = (DI_EN | WNR | DMAEN);	/* Destination DMAConfig Value (8-bit words) */
+
+DMA:
+	R6 = 0x1 (Z);
+	W[P1+OFFSET_(MDMA_S0_X_MODIFY)] = R6;	/* Source Modify = 1 */
+	W[P1+OFFSET_(MDMA_D0_X_MODIFY)] = R6;	/* Destination Modify = 1 */
+
+	[P1+OFFSET_(MDMA_S0_START_ADDR)] = R0;	/* Set Source Base Address */
+	W[P1+OFFSET_(MDMA_S0_X_COUNT)] = R2;	/* Set Source Count */
+	/* Set Source  DMAConfig = DMA Enable,
+	Memory Read,  8-Bit Transfers, 1-D DMA, Flow - Stop */
+	W[P1+OFFSET_(MDMA_S0_CONFIG)] = R3;
+
+	[P1+OFFSET_(MDMA_D0_START_ADDR)] = R1;	/* Set Destination Base Address */
+	W[P1+OFFSET_(MDMA_D0_X_COUNT)] = R2;	/* Set Destination Count */
+	/* Set Destination DMAConfig = DMA Enable,
+	Memory Write, 8-Bit Transfers, 1-D DMA, Flow - Stop, IOC */
+	W[P1+OFFSET_(MDMA_D0_CONFIG)] = R4;
+
+	IDLE;	/* Wait for DMA to Complete */
+
+	R0 = 0x1;
+	W[P1+OFFSET_(MDMA_D0_IRQ_STATUS)] = R0;	/* Write 1 to clear DMA interrupt */
+
+	/* DMA reset code to DATA BANK A which uses this port
+	 * to avoid following problem
+	 * " Data from a Data Cache fill can be corrupoted after or during
+	 *   instruction DMA if certain core stalls exist"
+	 */
+
+copy_as_data:
+	R0.H = reset_start;	/* Source Address (high) */
+	R0.L = reset_start;	/* Source Address (low) */
+	R1.H = reset_end;
+	R1.L = reset_end;
+	R2 = R1 - R0;	/* Count */
+	R1.H = hi(DATA_BANKA_SRAM);	/* Destination Address (high) */
+	R1.L = lo(DATA_BANKA_SRAM);	/* Destination Address (low) */
+	R3.L = DMAEN;	/* Source DMAConfig Value (8-bit words) */
+	R4.L = (DI_EN | WNR | DMAEN);	/* Destination DMAConfig Value (8-bit words) */
+
+DMA_DATA:
+	R6 = 0x1 (Z);
+	W[P1+OFFSET_(MDMA_S0_X_MODIFY)] = R6;	/* Source Modify = 1 */
+	W[P1+OFFSET_(MDMA_D0_X_MODIFY)] = R6;	/* Destination Modify = 1 */
+
+ 	[P1+OFFSET_(MDMA_S0_START_ADDR)] = R0;	/* Set Source Base Address */
+	W[P1+OFFSET_(MDMA_S0_X_COUNT)] = R2;	/* Set Source Count */
+	/* Set Source      DMAConfig = DMA Enable,
+	Memory Read,  8-Bit Transfers, 1-D DMA, Flow - Stop */
+	W[P1+OFFSET_(MDMA_S0_CONFIG)] = R3;
+
+	[P1+OFFSET_(MDMA_D0_START_ADDR)] = R1;	/* Set Destination Base Address */
+	W[P1+OFFSET_(MDMA_D0_X_COUNT)] = R2;	/* Set Destination Count */
+	/* Set Destination DMAConfig = DMA Enable,
+	Memory Write, 8-Bit Transfers, 1-D DMA, Flow - Stop, IOC */
+	W[P1+OFFSET_(MDMA_D0_CONFIG)] = R4;
+
+	IDLE;	/* Wait for DMA to Complete */
+
+	R0 = 0x1;
+	W[P1+OFFSET_(MDMA_D0_IRQ_STATUS)] = R0;	/* Write 1 to clear DMA interrupt */
+
+copy_end: nop;
+
+	/* Initialize BSS Section with 0 s */
+	p1.l = __bss_start;
+	p1.h = __bss_start;
+	p2.l = _end;
+	p2.h = _end;
+	r1 = p1;
+	r2 = p2;
+	r3 = r2 - r1;
+	r3 = r3 >> 2;
+	p3 = r3;
+	lsetup (_clear_bss, _clear_bss_end ) lc1 = p3;
+	CC = p2<=p1;
+	if CC jump _clear_bss_skip;
+	r0 = 0;
+_clear_bss:
+_clear_bss_end:
+ 	[p1++] = r0;
+_clear_bss_skip:
+
+	p0.l = _start1;
+	p0.h = _start1;
+	jump (p0);
+
+reset_start:
+	p0.h = WDOG_CNT >> 16;
+	p0.l = WDOG_CNT & 0xffff;
+	r0 = 0x0010;
+	w[p0] = r0;
+	p0.h = WDOG_CTL >> 16;
+	p0.l = WDOG_CTL & 0xffff;
+	r0 = 0x0000;
+	w[p0] = r0;
+reset_wait:
+	jump reset_wait;
+
+reset_end: nop;
+
+_exit:
+	jump.s	_exit;

cpu/bf533/start1.S

@@ -0,0 +1,38 @@
+/*
+ * U-boot - start1.S Code running out of RAM after relocation
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define ASSEMBLY
+#include <linux/config.h>
+#include <asm/blackfin.h>
+#include <config.h>
+
+.global	start1;
+.global	_start1;
+
+.text
+_start1:
+start1:
+	sp += -12;
+	call	board_init_f;
+	sp += 12;

cpu/bf533/traps.c

@@ -0,0 +1,73 @@
+/*
+ * U-boot - traps.c Routines related to interrupts and exceptions
+ *
+ * Copyright (c) 2005 blackfin.uclinux.org
+ *
+ * This file is based on
+ * No original Copyright holder listed,
+ * Probabily original (C) Roman Zippel (assigned DJD, 1999)
+ *
+ * Copyright 2003 Metrowerks - for Blackfin
+ * Copyright 2000-2001 Lineo, Inc. D. Jeff Dionne <jeff@lineo.ca>
+ * Copyright 1999-2000 D. Jeff Dionne, <jeff@uclinux.org>
+ *
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/types.h>
+#include <asm/errno.h>
+#include <asm/irq.h>
+#include <asm/system.h>
+#include <asm/traps.h>
+#include <asm/page.h>
+#include <asm/machdep.h>
+#include "cpu.h"
+
+void init_IRQ(void)
+{
+	blackfin_init_IRQ();
+	return;
+}
+
+void process_int(unsigned long vec, struct pt_regs *fp)
+{
+	return;
+}
+
+void dump(struct pt_regs *fp)
+{
+	printf("PC: %08lx\n", fp->pc);
+	printf("SEQSTAT: %08lx    SP: %08lx\n", (long) fp->seqstat,
+		(long) fp);
+	printf("R0: %08lx    R1: %08lx    R2: %08lx    R3: %08lx\n",
+		fp->r0, fp->r1, fp->r2, fp->r3);
+	printf("R4: %08lx    R5: %08lx    R6: %08lx    R7: %08lx\n",
+		fp->r4, fp->r5, fp->r6, fp->r7);
+	printf("P0: %08lx    P1: %08lx    P2: %08lx    P3: %08lx\n",
+		fp->p0, fp->p1, fp->p2, fp->p3);
+	printf("P4: %08lx    P5: %08lx    FP: %08lx\n", fp->p4, fp->p5,
+		fp->fp);
+	printf("A0.w: %08lx    A0.x: %08lx    A1.w: %08lx    A1.x: %08lx\n",
+		fp->a0w, fp->a0x, fp->a1w, fp->a1x);
+	printf("\n");
+}

cpu/mips/au1x00_eth.c

@@ -224,10 +224,14 @@ static void au1x00_halt(struct eth_device* dev){
 int au1x00_enet_initialize(bd_t *bis){
 	struct eth_device* dev;
 
-	dev = (struct eth_device*) malloc(sizeof *dev);
+	if ((dev = (struct eth_device*)malloc(sizeof *dev)) == NULL) {
+		puts ("malloc failed\n");
+		return 0;
+	}
+
 	memset(dev, 0, sizeof *dev);
 
-	sprintf(dev->name, "Au1X00 ETHERNET");
+	sprintf(dev->name, "Au1X00 ethernet");
 	dev->iobase = 0;
 	dev->priv   = 0;
 	dev->init   = au1x00_init;

cpu/mpc8260/speed.c

@@ -163,7 +163,7 @@ int prt_8260_clks (void)
 
 	volatile immap_t *immap = (immap_t *) CFG_IMMR;
 	ulong sccr, dfbrg;
-	ulong scmr, corecnf, busdf, cpmdf, plldf, pllmf;
+	ulong scmr, corecnf, busdf, cpmdf, plldf, pllmf, pcidf;
 	corecnf_t *cp;
 
 	sccr = immap->im_clkrst.car_sccr;
@@ -175,6 +175,7 @@ int prt_8260_clks (void)
 	cpmdf = (scmr & SCMR_CPMDF_MSK) >> SCMR_CPMDF_SHIFT;
 	plldf = (scmr & SCMR_PLLDF) ? 1 : 0;
 	pllmf = (scmr & SCMR_PLLMF_MSK) >> SCMR_PLLMF_SHIFT;
+	pcidf = (sccr & SCCR_PCIDF_MSK) >> SCCR_PCIDF_SHIFT;
 
 	cp = &corecnf_tab[corecnf];
 
@@ -204,8 +205,9 @@ int prt_8260_clks (void)
 			cp->vco_div, cp->freq_60x, cp->freq_core);
 
 	printf (" - dfbrg %ld, corecnf 0x%02lx, busdf %ld, cpmdf %ld, "
-			"plldf %ld, pllmf %ld\n", dfbrg, corecnf, busdf, cpmdf, plldf,
-			pllmf);
+		"plldf %ld, pllmf %ld, pcidf %ld\n",
+			dfbrg, corecnf, busdf, cpmdf,
+			plldf, pllmf, pcidf);
 
 	printf (" - vco_out %10ld, scc_clk %10ld, brg_clk %10ld\n",
 			gd->vco_out, gd->scc_clk, gd->brg_clk);
@@ -215,9 +217,20 @@ int prt_8260_clks (void)
 
 	if (sccr & SCCR_PCI_MODE) {
 		uint pci_div;
-
-		pci_div = ( (sccr & SCCR_PCI_MODCK) ? 2 : 1) *
-			( ( (sccr & SCCR_PCIDF_MSK) >> SCCR_PCIDF_SHIFT) + 1);
+		uint pcidf = (sccr & SCCR_PCIDF_MSK) >> SCCR_PCIDF_SHIFT;
+
+		if (sccr & SCCR_PCI_MODCK) {
+			pci_div = 2;
+			if (pcidf == 9) {
+				pci_div *= 5;
+			} else if (pcidf == 0xB) {
+				pci_div *= 6;
+			} else {
+				pci_div *= (pcidf + 1);
+			}
+		} else {
+			pci_div = pcidf + 1;
+		}
 
 		printf (" - pci_clk %10ld\n", (gd->cpm_clk * 2) / pci_div);
 	}
@@ -225,5 +238,3 @@ int prt_8260_clks (void)
 
 	return (0);
 }
-
-/* ------------------------------------------------------------------------- */

cpu/mpc83xx/cpu.c

@@ -35,6 +35,7 @@
 #include <watchdog.h>
 #include <command.h>
 #include <mpc83xx.h>
+#include <ft_build.h>
 #include <asm/processor.h>
 
 
@@ -92,6 +93,8 @@ do_reset (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
 
 	/* enable Reset Control Reg */
 	immap->reset.rpr = 0x52535445;
+	__asm__ __volatile__ ("sync");
+	__asm__ __volatile__ ("isync");
 
 	/* confirm Reset Control Reg is enabled */
 	while(!((immap->reset.rcer) & RCER_CRE));
@@ -151,3 +154,125 @@ void watchdog_reset (void)
 	hang();		/* FIXME: implement watchdog_reset()? */
 }
 #endif /* CONFIG_WATCHDOG */
+
+#if defined(CONFIG_OF_FLAT_TREE)
+void
+ft_cpu_setup(void *blob, bd_t *bd)
+{
+	u32 *p;
+	int len;
+	ulong clock;
+
+	clock = bd->bi_busfreq;
+	p = ft_get_prop(blob, "/cpus/" OF_CPU "/bus-frequency", &len);
+	if (p != NULL)
+		*p = cpu_to_be32(clock);
+
+	p = ft_get_prop(blob, "/" OF_SOC "/bus-frequency", &len);
+	if (p != NULL)
+		*p = cpu_to_be32(clock);
+
+	p = ft_get_prop(blob, "/" OF_SOC "/serial@4500/clock-frequency", &len);
+	if (p != NULL)
+		*p = cpu_to_be32(clock);
+
+	p = ft_get_prop(blob, "/" OF_SOC "/serial@4600/clock-frequency", &len);
+	if (p != NULL)
+		*p = cpu_to_be32(clock);
+
+#ifdef CONFIG_MPC83XX_TSEC1
+	p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/address", &len);
+		memcpy(p, bd->bi_enetaddr, 6);
+#endif
+
+#ifdef CONFIG_MPC83XX_TSEC2
+	p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/address", &len);
+		memcpy(p, bd->bi_enet1addr, 6);
+#endif
+}
+#endif
+
+#if defined(CONFIG_DDR_ECC)
+void dma_init(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+	volatile dma8349_t *dma = &immap->dma;
+	volatile u32 status = swab32(dma->dmasr0);
+	volatile u32 dmamr0 = swab32(dma->dmamr0);
+
+	debug("DMA-init\n");
+
+	/* initialize DMASARn, DMADAR and DMAABCRn */
+	dma->dmadar0 = (u32)0;
+	dma->dmasar0 = (u32)0;
+	dma->dmabcr0 = 0;
+
+	__asm__ __volatile__ ("sync");
+	__asm__ __volatile__ ("isync");
+
+	/* clear CS bit */
+	dmamr0 &= ~DMA_CHANNEL_START;
+	dma->dmamr0 = swab32(dmamr0);
+	__asm__ __volatile__ ("sync");
+	__asm__ __volatile__ ("isync");
+
+	/* while the channel is busy, spin */
+	while(status & DMA_CHANNEL_BUSY) {
+		status = swab32(dma->dmasr0);
+	}
+
+	debug("DMA-init end\n");
+}
+
+uint dma_check(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+	volatile dma8349_t *dma = &immap->dma;
+	volatile u32 status = swab32(dma->dmasr0);
+	volatile u32 byte_count = swab32(dma->dmabcr0);
+
+	/* while the channel is busy, spin */
+	while (status & DMA_CHANNEL_BUSY) {
+		status = swab32(dma->dmasr0);
+	}
+
+	if (status & DMA_CHANNEL_TRANSFER_ERROR) {
+		printf ("DMA Error: status = %x @ %d\n", status, byte_count);
+	}
+
+	return status;
+}
+
+int dma_xfer(void *dest, u32 count, void *src)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
+	volatile dma8349_t *dma = &immap->dma;
+	volatile u32 dmamr0;
+
+	/* initialize DMASARn, DMADAR and DMAABCRn */
+	dma->dmadar0 = swab32((u32)dest);
+	dma->dmasar0 = swab32((u32)src);
+	dma->dmabcr0 = swab32(count);
+
+	__asm__ __volatile__ ("sync");
+	__asm__ __volatile__ ("isync");
+
+	/* init direct transfer, clear CS bit */
+	dmamr0 = (DMA_CHANNEL_TRANSFER_MODE_DIRECT |
+			DMA_CHANNEL_SOURCE_ADDRESS_HOLD_8B |
+			DMA_CHANNEL_SOURCE_ADRESSS_HOLD_EN);
+	
+	dma->dmamr0 = swab32(dmamr0);
+
+	__asm__ __volatile__ ("sync");
+	__asm__ __volatile__ ("isync");
+
+	/* set CS to start DMA transfer */
+	dmamr0 |= DMA_CHANNEL_START;
+	dma->dmamr0 = swab32(dmamr0);
+	__asm__ __volatile__ ("sync");
+	__asm__ __volatile__ ("isync");
+
+	return ((int)dma_check());
+}
+#endif /*CONFIG_DDR_ECC*/

cpu/mpc83xx/cpu_init.c

@@ -63,8 +63,12 @@ void cpu_init_f (volatile immap_t * im)
 	im->sysconf.spcr |= SPCR_TBEN;
 
 	/* System General Purpose Register */
-	im->sysconf.sicrh = SICRH_TSOBI1;
-	im->sysconf.sicrl = SICRL_LDP_A;
+#ifdef CFG_SICRH
+	im->sysconf.sicrh = CFG_SICRH;
+#endif
+#ifdef CFG_SICRL
+	im->sysconf.sicrl = CFG_SICRL;
+#endif
 
 	/*
 	 * Memory Controller:
@@ -87,69 +91,70 @@ void cpu_init_f (volatile immap_t * im)
 #error 	CFG_BR0_PRELIM, CFG_OR0_PRELIM, CFG_LBLAWBAR0_PRELIM & CFG_LBLAWAR0_PRELIM must be defined
 #endif
 
-#if defined(CFG_BR1_PRELIM)  \
-	&& defined(CFG_OR1_PRELIM) \
-	&& defined(CFG_LBLAWBAR1_PRELIM) \
-	&& defined(CFG_LBLAWAR1_PRELIM)
+#if defined(CFG_BR1_PRELIM) && defined(CFG_OR1_PRELIM)
 	im->lbus.bank[1].br = CFG_BR1_PRELIM;
 	im->lbus.bank[1].or = CFG_OR1_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR1_PRELIM) && defined(CFG_LBLAWAR1_PRELIM)
 	im->sysconf.lblaw[1].bar = CFG_LBLAWBAR1_PRELIM;
 	im->sysconf.lblaw[1].ar = CFG_LBLAWAR1_PRELIM;
 #endif
-#if defined(CFG_BR2_PRELIM)  \
-	&& defined(CFG_OR2_PRELIM) \
-	&& defined(CFG_LBLAWBAR2_PRELIM) \
-	&& defined(CFG_LBLAWAR2_PRELIM)
+#if defined(CFG_BR2_PRELIM) && defined(CFG_OR2_PRELIM)
 	im->lbus.bank[2].br = CFG_BR2_PRELIM;
 	im->lbus.bank[2].or = CFG_OR2_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR2_PRELIM) && defined(CFG_LBLAWAR2_PRELIM)
 	im->sysconf.lblaw[2].bar = CFG_LBLAWBAR2_PRELIM;
 	im->sysconf.lblaw[2].ar = CFG_LBLAWAR2_PRELIM;
 #endif
-#if defined(CFG_BR3_PRELIM)  \
-	&& defined(CFG_OR3_PRELIM) \
-	&& defined(CFG_LBLAWBAR3_PRELIM) \
-	&& defined(CFG_LBLAWAR3_PRELIM)
+#if defined(CFG_BR3_PRELIM) && defined(CFG_OR3_PRELIM)
 	im->lbus.bank[3].br = CFG_BR3_PRELIM;
 	im->lbus.bank[3].or = CFG_OR3_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR3_PRELIM) && defined(CFG_LBLAWAR3_PRELIM)
 	im->sysconf.lblaw[3].bar = CFG_LBLAWBAR3_PRELIM;
 	im->sysconf.lblaw[3].ar = CFG_LBLAWAR3_PRELIM;
 #endif
-#if defined(CFG_BR4_PRELIM)  \
-	&& defined(CFG_OR4_PRELIM) \
-	&& defined(CFG_LBLAWBAR4_PRELIM) \
-	&& defined(CFG_LBLAWAR4_PRELIM)
+#if defined(CFG_BR4_PRELIM) && defined(CFG_OR4_PRELIM)
 	im->lbus.bank[4].br = CFG_BR4_PRELIM;
 	im->lbus.bank[4].or = CFG_OR4_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR4_PRELIM) && defined(CFG_LBLAWAR4_PRELIM)
 	im->sysconf.lblaw[4].bar = CFG_LBLAWBAR4_PRELIM;
 	im->sysconf.lblaw[4].ar = CFG_LBLAWAR4_PRELIM;
 #endif
-#if defined(CFG_BR5_PRELIM)  \
-	&& defined(CFG_OR5_PRELIM) \
-	&& defined(CFG_LBLAWBAR5_PRELIM) \
-	&& defined(CFG_LBLAWAR5_PRELIM)
+#if defined(CFG_BR5_PRELIM) && defined(CFG_OR5_PRELIM)
 	im->lbus.bank[5].br = CFG_BR5_PRELIM;
 	im->lbus.bank[5].or = CFG_OR5_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR5_PRELIM) && defined(CFG_LBLAWAR5_PRELIM)
 	im->sysconf.lblaw[5].bar = CFG_LBLAWBAR5_PRELIM;
 	im->sysconf.lblaw[5].ar = CFG_LBLAWAR5_PRELIM;
 #endif
-#if defined(CFG_BR6_PRELIM)  \
-	&& defined(CFG_OR6_PRELIM) \
-	&& defined(CFG_LBLAWBAR6_PRELIM) \
-	&& defined(CFG_LBLAWAR6_PRELIM)
+#if defined(CFG_BR6_PRELIM) && defined(CFG_OR6_PRELIM)
 	im->lbus.bank[6].br = CFG_BR6_PRELIM;
 	im->lbus.bank[6].or = CFG_OR6_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR6_PRELIM) && defined(CFG_LBLAWAR6_PRELIM)
 	im->sysconf.lblaw[6].bar = CFG_LBLAWBAR6_PRELIM;
 	im->sysconf.lblaw[6].ar = CFG_LBLAWAR6_PRELIM;
 #endif
-#if defined(CFG_BR7_PRELIM)  \
-	&& defined(CFG_OR7_PRELIM) \
-	&& defined(CFG_LBLAWBAR7_PRELIM) \
-	&& defined(CFG_LBLAWAR7_PRELIM)
+#if defined(CFG_BR7_PRELIM) && defined(CFG_OR7_PRELIM)
 	im->lbus.bank[7].br = CFG_BR7_PRELIM;
 	im->lbus.bank[7].or = CFG_OR7_PRELIM;
+#endif
+#if defined(CFG_LBLAWBAR7_PRELIM) && defined(CFG_LBLAWAR7_PRELIM)
 	im->sysconf.lblaw[7].bar = CFG_LBLAWBAR7_PRELIM;
 	im->sysconf.lblaw[7].ar = CFG_LBLAWAR7_PRELIM;
 #endif
+#ifdef CFG_GPIO1_PRELIM
+	im->pgio[0].dir = CFG_GPIO1_DIR;
+	im->pgio[0].dat = CFG_GPIO1_DAT;
+#endif
+#ifdef CFG_GPIO2_PRELIM
+	im->pgio[1].dir = CFG_GPIO2_DIR;
+	im->pgio[1].dat = CFG_GPIO2_DAT;
+#endif
 }
 
 

cpu/mpc83xx/interrupts.c

@@ -43,6 +43,16 @@ struct irq_action {
 
 int interrupt_init_cpu (unsigned *decrementer_count)
 {
+	DECLARE_GLOBAL_DATA_PTR;
+
+	volatile immap_t *immr = (immap_t *) CFG_IMMRBAR;
+
+	*decrementer_count = (gd->bus_clk / 4) / CFG_HZ;
+
+	/* Enable e300 time base */
+
+	immr->sysconf.spcr |= 0x00400000;
+
 	return 0;
 }
 

cpu/mpc83xx/spd_sdram.c

@@ -1,4 +1,7 @@
 /*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * 
  * Copyright 2004 Freescale Semiconductor.
  * (C) Copyright 2003 Motorola Inc.
  * Xianghua Xiao (X.Xiao@motorola.com)
@@ -63,13 +66,42 @@ picos_to_clk(int picos)
 	return clks;
 }
 
-unsigned int
-banksize(unsigned char row_dens)
+unsigned int banksize(unsigned char row_dens)
 {
 	return ((row_dens >> 2) | ((row_dens & 3) << 6)) << 24;
 }
 
-long int spd_sdram(int(read_spd)(uint addr))
+int read_spd(uint addr)
+{
+	return ((int) addr);
+}
+
+#undef SPD_DEBUG
+#ifdef SPD_DEBUG
+static void spd_debug(spd_eeprom_t *spd)
+{
+	printf ("\nDIMM type:       %-18.18s\n", spd->mpart);
+	printf ("SPD size:        %d\n", spd->info_size);
+	printf ("EEPROM size:     %d\n", 1 << spd->chip_size);
+	printf ("Memory type:     %d\n", spd->mem_type);
+	printf ("Row addr:        %d\n", spd->nrow_addr);
+	printf ("Column addr:     %d\n", spd->ncol_addr);
+	printf ("# of rows:       %d\n", spd->nrows);
+	printf ("Row density:     %d\n", spd->row_dens);
+	printf ("# of banks:      %d\n", spd->nbanks);
+	printf ("Data width:      %d\n",
+			256 * spd->dataw_msb + spd->dataw_lsb);
+	printf ("Chip width:      %d\n", spd->primw);
+	printf ("Refresh rate:    %02X\n", spd->refresh);
+	printf ("CAS latencies:   %02X\n", spd->cas_lat);
+	printf ("Write latencies: %02X\n", spd->write_lat);
+	printf ("tRP:             %d\n", spd->trp);
+	printf ("tRCD:            %d\n", spd->trcd);
+	printf ("\n");
+}
+#endif /* SPD_DEBUG */
+
+long int spd_sdram()
 {
 	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
 	volatile ddr8349_t *ddr = &immap->ddr;
@@ -81,10 +113,10 @@ long int spd_sdram(int(read_spd)(uint addr))
 	unsigned char caslat;
 	unsigned int trfc, trfc_clk, trfc_low;
 
-#warning Current spd_sdram does not fit its usage... adjust implementation or API...
-
 	CFG_READ_SPD(SPD_EEPROM_ADDRESS, 0, 1, (uchar *) & spd, sizeof (spd));
-
+#ifdef SPD_DEBUG
+	spd_debug(&spd);
+#endif
 	if (spd.nrows > 2) {
 		puts("DDR:Only two chip selects are supported on ADS.\n");
 		return 0;
@@ -219,25 +251,31 @@ long int spd_sdram(int(read_spd)(uint addr))
 	 * Only DDR I is supported
 	 * DDR I and II have different mode-register-set definition
 	 */
-
-	/* burst length is always 4 */
 	switch(caslat) {
 	case 2:
-		ddr->sdram_mode = 0x52; /* 1.5 */
+		tmp = 0x50; /* 1.5 */
 		break;
 	case 3:
-		ddr->sdram_mode = 0x22; /* 2.0 */
+		tmp = 0x20; /* 2.0 */
 		break;
 	case 4:
-		ddr->sdram_mode = 0x62; /* 2.5 */
+		tmp = 0x60; /* 2.5 */
 		break;
 	case 5:
-		ddr->sdram_mode = 0x32; /* 3.0 */
+		tmp = 0x30; /* 3.0 */
 		break;
 	default:
 		puts("DDR:only CAS Latency 1.5, 2.0, 2.5, 3.0 is supported.\n");
 		return 0;
 	}
+#if defined (CONFIG_DDR_32BIT)
+	/* set burst length to 8 for 32-bit data path */
+	tmp |= 0x03;
+#else
+	/* set burst length to 4 - default for 64-bit data path */
+	tmp |= 0x02;
+#endif
+	ddr->sdram_mode = tmp;
 	debug("DDR:sdram_mode=0x%08x\n", ddr->sdram_mode);
 
 	switch(spd.refresh) {
@@ -282,8 +320,13 @@ long int spd_sdram(int(read_spd)(uint addr))
 	 */
 #if defined(CONFIG_DDR_ECC)
 	if (spd.config == 0x02) {
-		ddr->err_disable = 0x0000000d;
-		ddr->err_sbe = 0x00ff0000;
+		/* disable error detection */
+		ddr->err_disable = ~ECC_ERROR_ENABLE;
+
+		/* set single bit error threshold to maximum value,
+		 * reset counter to zero */
+		ddr->err_sbe = (255 << ECC_ERROR_MAN_SBET_SHIFT) |
+			(0 << ECC_ERROR_MAN_SBEC_SHIFT);
 	}
 	debug("DDR:err_disable=0x%08x\n", ddr->err_disable);
 	debug("DDR:err_sbe=0x%08x\n", ddr->err_sbe);
@@ -297,7 +340,8 @@ long int spd_sdram(int(read_spd)(uint addr))
 	 * CLK_ADJST = 2-MCK/MCK_B, is lauched 1/2 of one SDRAM
 	 * clock cycle after address/command
 	 */
-	ddr->sdram_clk_cntl = 0x82000000;
+	/*ddr->sdram_clk_cntl = 0x82000000;*/
+	ddr->sdram_clk_cntl = (DDR_SDRAM_CLK_CNTL_SS_EN|DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05);
 
 	/*
 	 * Figure out the settings for the sdram_cfg register.  Build up
@@ -311,6 +355,10 @@ long int spd_sdram(int(read_spd)(uint addr))
 	 */
 	tmp = 0xc2000000;
 
+#if defined (CONFIG_DDR_32BIT)
+	/* in 32-Bit mode burst len is 8 beats */
+	tmp |= (SDRAM_CFG_32_BE | SDRAM_CFG_8_BE);
+#endif
 	/*
 	 * sdram_cfg[3] = RD_EN - registered DIMM enable
 	 *   A value of 0x26 indicates micron registered DIMMS (micron.com)
@@ -324,7 +372,7 @@ long int spd_sdram(int(read_spd)(uint addr))
 	 * If the user wanted ECC (enabled via sdram_cfg[2])
 	 */
 	if (spd.config == 0x02) {
-		tmp |= 0x20000000;
+		tmp |= SDRAM_CFG_ECC_EN;
 	}
 #endif
 
@@ -340,37 +388,94 @@ long int spd_sdram(int(read_spd)(uint addr))
 	udelay(500);
 
 	debug("DDR:sdram_cfg=0x%08x\n", ddr->sdram_cfg);
-
-	return memsize;/*in MBytes*/
+	return memsize; /*in MBytes*/
 }
 #endif /* CONFIG_SPD_EEPROM */
 
 
 #if defined(CONFIG_DDR_ECC)
 /*
- * Initialize all of memory for ECC, then enable errors.
+ * Use timebase counter, get_timer() is not availabe
+ * at this point of initialization yet.
  */
+static __inline__ unsigned long get_tbms (void)
+{
+	unsigned long tbl;
+	unsigned long tbu1, tbu2;
+	unsigned long ms;
+	unsigned long long tmp;
+
+	ulong tbclk = get_tbclk();
+
+	/* get the timebase ticks */
+	do {
+		asm volatile ("mftbu %0":"=r" (tbu1):);
+		asm volatile ("mftb %0":"=r" (tbl):);
+		asm volatile ("mftbu %0":"=r" (tbu2):);
+	} while (tbu1 != tbu2);
+
+	/* convert ticks to ms */
+	tmp = (unsigned long long)(tbu1);
+	tmp = (tmp << 32);
+	tmp += (unsigned long long)(tbl);
+	ms = tmp/(tbclk/1000);
+
+	return ms;
+}
 
-void
-ddr_enable_ecc(unsigned int dram_size)
+/*
+ * Initialize all of memory for ECC, then enable errors.
+ */
+//#define CONFIG_DDR_ECC_INIT_VIA_DMA
+void ddr_enable_ecc(unsigned int dram_size)
 {
-#ifndef FIXME
-	uint *p = 0;
-	uint i = 0;
+	uint *p;
 	volatile immap_t *immap = (immap_t *)CFG_IMMRBAR;
-	volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+	volatile ddr8349_t *ddr = &immap->ddr;
+	unsigned long t_start, t_end;
+#if defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
+	uint i;
+#endif
+
+	debug("Initialize a Cachline in DRAM\n");
+	icache_enable();
 
+#if defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
+	/* Initialise DMA for direct Transfers */
 	dma_init();
+#endif
+
+	t_start = get_tbms();
 
-	for (*p = 0; p < (uint *)(8 * 1024); p++) {
+#if !defined(CONFIG_DDR_ECC_INIT_VIA_DMA)
+	debug("DDR init: Cache flush method\n");
+	for (p = 0; p < (uint *)(dram_size); p++) {
 		if (((unsigned int)p & 0x1f) == 0) {
 			ppcDcbz((unsigned long) p);
 		}
+
+		/* write pattern to cache and flush */
 		*p = (unsigned int)0xdeadbeef;
+
 		if (((unsigned int)p & 0x1c) == 0x1c) {
 			ppcDcbf((unsigned long) p);
 		}
 	}
+#else
+	printf("DDR init: DMA method\n");
+	for (p = 0; p < (uint *)(8 * 1024); p++) {
+		/* zero one data cache line */
+		if (((unsigned int)p & 0x1f) == 0) {
+			ppcDcbz((unsigned long)p);
+		}
+
+		/* write pattern to it and flush */
+		*p = (unsigned int)0xdeadbeef;
+
+		if (((unsigned int)p & 0x1c) == 0x1c) {
+			ppcDcbf((unsigned long)p);
+		}
+	}
 
 	/* 8K */
 	dma_xfer((uint *)0x2000, 0x2000, (uint *)0);
@@ -396,13 +501,31 @@ ddr_enable_ecc(unsigned int dram_size)
 	for (i = 1; i < dram_size / 0x800000; i++) {
 		dma_xfer((uint *)(0x800000*i), 0x800000, (uint *)0);
 	}
-
-	/*
-	 * Enable errors for ECC.
-	 */
-	ddr->err_disable = 0x00000000;
-	asm("sync;isync");
 #endif
-}
 
+	t_end = get_tbms();
+	icache_disable();
+
+	debug("\nREADY!!\n");
+	debug("ddr init duration: %ld ms\n", t_end - t_start);
+
+	/* Clear All ECC Errors */
+	if ((ddr->err_detect & ECC_ERROR_DETECT_MME) == ECC_ERROR_DETECT_MME)
+		ddr->err_detect |= ECC_ERROR_DETECT_MME;
+	if ((ddr->err_detect & ECC_ERROR_DETECT_MBE) == ECC_ERROR_DETECT_MBE)
+		ddr->err_detect |= ECC_ERROR_DETECT_MBE;
+	if ((ddr->err_detect & ECC_ERROR_DETECT_SBE) == ECC_ERROR_DETECT_SBE)
+		ddr->err_detect |= ECC_ERROR_DETECT_SBE;
+	if ((ddr->err_detect & ECC_ERROR_DETECT_MSE) == ECC_ERROR_DETECT_MSE)
+		ddr->err_detect |= ECC_ERROR_DETECT_MSE;
+
+	/* Disable ECC-Interrupts */
+	ddr->err_int_en &= ECC_ERR_INT_DISABLE;
+
+	/* Enable errors for ECC */
+	ddr->err_disable &= ECC_ERROR_ENABLE;
+
+	__asm__ __volatile__ ("sync");
+	__asm__ __volatile__ ("isync");
+}
 #endif	/* CONFIG_DDR_ECC */