powerpc/km82xx: remove 82xx specific functions from common.c

Common code should be valid for more than one architecture,
therefore the km82xx specific code was removed from common.c.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>

board/keymile/common/common.c

@@ -25,9 +25,6 @@
  */
 
 #include <common.h>
-#if defined(CONFIG_KM82XX)
-#include <mpc8260.h>
-#endif
 #include <ioports.h>
 #include <command.h>
 #include <malloc.h>
@@ -44,6 +41,7 @@
 #include "common.h"
 #if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
 #include <i2c.h>
+#endif
 
 static void i2c_write_start_seq(void);
 DECLARE_GLOBAL_DATA_PTR;
@@ -83,70 +81,9 @@ int set_km_env(void)
 	return 0;
 }
 
-#if defined(CONFIG_SYS_I2C_INIT_BOARD)
 #define DELAY_ABORT_SEQ		62  /* @200kHz 9 clocks = 44us, 62us is ok */
 #define DELAY_HALF_PERIOD	(500 / (CONFIG_SYS_I2C_SPEED / 1000))
 
-#if defined(CONFIG_KM_82XX)
-#define SDA_MASK	0x00010000
-#define SCL_MASK	0x00020000
-void set_pin(int state, unsigned long mask)
-{
-	ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
-
-	if (state)
-		setbits_be32(&iop->pdat, mask);
-	else
-		clrbits_be32(&iop->pdat, mask);
-
-	setbits_be32(&iop->pdir, mask);
-}
-
-static int get_pin(unsigned long mask)
-{
-	ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
-
-	clrbits_be32(&iop->pdir, mask);
-	return 0 != (in_be32(&iop->pdat) & mask);
-}
-
-static void set_sda(int state)
-{
-	set_pin(state, SDA_MASK);
-}
-
-static void set_scl(int state)
-{
-	set_pin(state, SCL_MASK);
-}
-
-static int get_sda(void)
-{
-	return get_pin(SDA_MASK);
-}
-
-static int get_scl(void)
-{
-	return get_pin(SCL_MASK);
-}
-
-#if defined(CONFIG_HARD_I2C)
-static void setports(int gpio)
-{
-	ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
-
-	if (gpio) {
-		clrbits_be32(&iop->ppar, (SDA_MASK | SCL_MASK));
-		clrbits_be32(&iop->podr, (SDA_MASK | SCL_MASK));
-	} else {
-		setbits_be32(&iop->ppar, (SDA_MASK | SCL_MASK));
-		clrbits_be32(&iop->pdir, (SDA_MASK | SCL_MASK));
-		setbits_be32(&iop->podr, (SDA_MASK | SCL_MASK));
-	}
-}
-#endif
-#endif
-
 #if !defined(CONFIG_MPC83xx)
 static void i2c_write_start_seq(void)
 {
@@ -223,7 +160,7 @@ int i2c_make_abort(void)
 #endif
 	return ret;
 }
-#endif
+#endif /* !MPC83xx */
 
 #if defined(CONFIG_MPC83xx)
 static void i2c_write_start_seq(void)
@@ -296,8 +233,6 @@ void i2c_init_board(void)
 	/* Now run the AbortSequence() */
 	i2c_make_abort();
 }
-#endif
-#endif
 
 #if !defined(MACH_TYPE_KM_KIRKWOOD)
 int ethernet_present(void)

board/keymile/common/common.h

@@ -124,7 +124,6 @@ struct bfticu_iomap {
 
 int ethernet_present(void);
 int ivm_read_eeprom(void);
-void set_pin(int state, unsigned long mask);
 
 int set_km_env(void);
 int fdt_set_node_and_value(void *blob,

board/keymile/km82xx/km82xx.c

@@ -315,6 +315,8 @@ int last_stage_init(void)
 }
 
 #ifdef CONFIG_MGCOGE3NE
+static void set_pin(int state, unsigned long mask);
+
 /*
  * For mgcoge3ne boards, the mgcoge3un control is controlled from
  * a GPIO line on the PPC CPU. If bobcatreset is set the line
@@ -363,6 +365,64 @@ int hush_init_var(void)
 	return 0;
 }
 
+#define SDA_MASK	0x00010000
+#define SCL_MASK	0x00020000
+
+static void set_pin(int state, unsigned long mask)
+{
+	ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
+
+	if (state)
+		setbits_be32(&iop->pdat, mask);
+	else
+		clrbits_be32(&iop->pdat, mask);
+
+	setbits_be32(&iop->pdir, mask);
+}
+
+static int get_pin(unsigned long mask)
+{
+	ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
+
+	clrbits_be32(&iop->pdir, mask);
+	return 0 != (in_be32(&iop->pdat) & mask);
+}
+
+void set_sda(int state)
+{
+	set_pin(state, SDA_MASK);
+}
+
+void set_scl(int state)
+{
+	set_pin(state, SCL_MASK);
+}
+
+int get_sda(void)
+{
+	return get_pin(SDA_MASK);
+}
+
+int get_scl(void)
+{
+	return get_pin(SCL_MASK);
+}
+
+#if defined(CONFIG_HARD_I2C)
+static void setports(int gpio)
+{
+	ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, 3);
+
+	if (gpio) {
+		clrbits_be32(&iop->ppar, (SDA_MASK | SCL_MASK));
+		clrbits_be32(&iop->podr, (SDA_MASK | SCL_MASK));
+	} else {
+		setbits_be32(&iop->ppar, (SDA_MASK | SCL_MASK));
+		clrbits_be32(&iop->pdir, (SDA_MASK | SCL_MASK));
+		setbits_be32(&iop->podr, (SDA_MASK | SCL_MASK));
+	}
+}
+#endif
 #if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
 void ft_board_setup(void *blob, bd_t *bd)
 {

include/configs/km/km82xx-common.h

@@ -139,6 +139,13 @@
 			} while (0)
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
 
+#ifndef __ASSEMBLY__
+void set_sda(int state);
+void set_scl(int state);
+int get_sda(void);
+int get_scl(void);
+#endif
+
 /* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
 #define CONFIG_DTT_LM75			/* ON Semi's LM75		*/
 #define CONFIG_DTT_SENSORS	{0}	/* Sensor addresses		*/