drivers/block: Move conditional compilation to Makefile

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

drivers/block/Makefile

@@ -25,14 +25,14 @@ include $(TOPDIR)/config.mk
 
 LIB	:= $(obj)libblock.a
 
-COBJS-y += ahci.o
-COBJS-y += ata_piix.o
+COBJS-$(CONFIG_SCSI_AHCI) += ahci.o
+COBJS-$(CONFIG_ATA_PIIX) += ata_piix.o
 COBJS-$(CONFIG_FSL_SATA) += fsl_sata.o
 COBJS-$(CONFIG_LIBATA) += libata.o
 COBJS-$(CONFIG_SATA_SIL3114) += sata_sil3114.o
-COBJS-y += sil680.o
-COBJS-y += sym53c8xx.o
-COBJS-y += systemace.o
+COBJS-$(CONFIG_IDE_SIL680) += sil680.o
+COBJS-$(CONFIG_SCSI_SYM53C8XX) += sym53c8xx.o
+COBJS-$(CONFIG_SYSTEMACE) += systemace.o
 
 COBJS	:= $(COBJS-y)
 SRCS	:= $(COBJS:.o=.c)

drivers/block/ahci.c

@@ -26,8 +26,6 @@
  */
 #include <common.h>
 
-#ifdef CONFIG_SCSI_AHCI
-
 #include <command.h>
 #include <pci.h>
 #include <asm/processor.h>
@@ -700,4 +698,3 @@ void scsi_print_error(ccb * pccb)
 {
 	/*The ahci error info can be read in the ahci driver*/
 }
-#endif

drivers/block/ata_piix.c

@@ -35,8 +35,6 @@
 #include <ide.h>
 #include <ata.h>
 
-#ifdef CFG_ATA_PIIX		/*ata_piix driver */
-
 extern block_dev_desc_t sata_dev_desc[CFG_SATA_MAX_DEVICE];
 extern int curr_device;
 
@@ -756,5 +754,3 @@ int scan_sata(int dev)
 {
 	return 0;
 }
-
-#endif

drivers/block/sil680.c

@@ -27,7 +27,7 @@
  * The following parameters must be defined in the configuration file
  * of the target board:
  *
- * #define CFG_IDE_SIL680
+ * #define CONFIG_IDE_SIL680
  *
  * #define CONFIG_PCI_PNP
  * NOTE it may also be necessary to define this if the default of 8 is
@@ -54,7 +54,6 @@
  */
 
 #include <common.h>
-#if defined(CFG_IDE_SIL680)
 #include <ata.h>
 #include <ide.h>
 #include <pci.h>
@@ -106,5 +105,3 @@ int ide_preinit (void)
 void ide_set_reset (int flag) {
 	return;
 }
-
-#endif /* CFG_IDE_SIL680 */

drivers/block/sym53c8xx.c

@@ -35,8 +35,6 @@
 
 #include <common.h>
 
-#ifdef CONFIG_SCSI_SYM53C8XX
-
 #include <command.h>
 #include <pci.h>
 #include <asm/processor.h>
@@ -870,6 +868,3 @@ void scsi_chip_init(void)
 #endif
 }
 #endif
-
-
-#endif /* CONFIG_SCSI_SYM53C8XX */

drivers/block/systemace.c

@@ -44,8 +44,6 @@
 #include <part.h>
 #include <asm/io.h>
 
-#ifdef CONFIG_SYSTEMACE
-
 /*
  * The ace_readw and writew functions read/write 16bit words, but the
  * offset value is the BYTE offset as most used in the Xilinx
@@ -255,4 +253,3 @@ static unsigned long systemace_read(int dev, unsigned long start,
 
 	return blkcnt;
 }
-#endif /* CONFIG_SYSTEMACE */

include/configs/sc520_cdp.h

@@ -178,7 +178,7 @@
 #define CFG_SATA_MAXBUS         2       /*Max Sata buses supported */
 #define CFG_SATA_DEVS_PER_BUS   2      /*Max no. of devices per bus/port */
 #define CFG_SATA_MAX_DEVICE     (CFG_SATA_MAXBUS* CFG_SATA_DEVS_PER_BUS)
-#define CFG_ATA_PIIX            1       /*Supports ata_piix driver */
+#define CONFIG_ATA_PIIX		1       /*Supports ata_piix driver */
 
 /************************************************************
  * DISK Partition support