u8500: Separating mmc config parameters from driver

Configuration in vexpress and u8500.v1 is different from what
is needed in u8500.v2.  As such, card configuration specifics need
to reside in the board file rather than the driver.

Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>

board/armltd/vexpress/ca9x4_ct_vxp.c

@@ -33,6 +33,8 @@
  * MA 02111-1307 USA
  */
 #include <common.h>
+#include <malloc.h>
+#include <errno.h>
 #include <netdev.h>
 #include <asm/io.h>
 #include <asm/arch/systimer.h>
@@ -90,8 +92,25 @@ int board_eth_init(bd_t *bis)
 int cpu_mmc_init(bd_t *bis)
 {
 	int rc = 0;
+	(void) bis;
 #ifdef CONFIG_ARM_PL180_MMCI
-	rc = arm_pl180_mmci_init();
+	struct pl180_mmc_host *host;
+
+	host = malloc(sizeof(struct pl180_mmc_host));
+	if (!host)
+		return -ENOMEM;
+	memset(host, 0, sizeof(*host));
+
+	strcpy(host->name, "MMC");
+	host->base = (struct sdi_registers *)CONFIG_ARM_PL180_MMCI_BASE;
+	host->pwr_init = INIT_PWR;
+	host->clkdiv_init = SDI_CLKCR_CLKDIV_INIT_V1 | SDI_CLKCR_CLKEN;
+	host->voltages = VOLTAGE_WINDOW_MMC;
+	host->caps = 0;
+	host->clock_in = ARM_MCLK;
+	host->clock_min = ARM_MCLK / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 + 1));
+	host->clock_max = CONFIG_ARM_PL180_MMCI_CLOCK_FREQ;
+	rc = arm_pl180_mmci_init(host);
 #endif
 	return rc;
 }

board/st-ericsson/snowball/snowball.c

@@ -29,6 +29,9 @@
 #include <asm/arch/hardware.h>
 #include <asm/arch/sys_proto.h>
 
+#ifdef CONFIG_MMC
+#include "../../../drivers/mmc/arm_pl180_mmci.h"
+#endif
 #include "db8500_pins.h"
 
 /*
@@ -250,9 +253,96 @@ int board_late_init(void)
 	if ((raise_ab8500_gpio16() < 0))
 		printf("error: cant' raise GPIO16\n");
 
+	return 0;
+}
+
 #ifdef CONFIG_MMC
+/*
+ * emmc_host_init - initialize the emmc controller.
+ * Configure GPIO settings, set initial clock and power for emmc slot.
+ * Initialize mmc struct and register with mmc framework.
+ */
+static int emmc_host_init(void)
+{
+	struct pl180_mmc_host *host;
+
+	host = malloc(sizeof(struct pl180_mmc_host));
+	if (!host)
+		return -ENOMEM;
+	memset(host, 0, sizeof(*host));
+
+	host->base = (struct sdi_registers *)CFG_EMMC_BASE;
+	host->pwr_init = SDI_PWR_OPD | SDI_PWR_PWRCTRL_ON;
+	host->clkdiv_init = SDI_CLKCR_CLKDIV_INIT_V2 |
+				 SDI_CLKCR_CLKEN | SDI_CLKCR_HWFC_EN;
+	strcpy(host->name, "EMMC");
+	host->caps = MMC_MODE_8BIT | MMC_MODE_HS | MMC_MODE_HS_52MHz;
+	host->voltages = VOLTAGE_WINDOW_MMC;
+	host->clock_min = ARM_MCLK / (2 + SDI_CLKCR_CLKDIV_INIT_V2);
+	host->clock_max = ARM_MCLK / 2;
+	host->clock_in = ARM_MCLK;
+	host->version2 = 1;
+
+	return arm_pl180_mmci_init(host);
+}
+
+/*
+ * mmc_host_init - initialize the external mmc controller.
+ * Configure GPIO settings, set initial clock and power for mmc slot.
+ * Initialize mmc struct and register with mmc framework.
+ */
+static int mmc_host_init(void)
+{
+	struct pl180_mmc_host *host;
+	u32 sdi_u32;
+
+	host = malloc(sizeof(struct pl180_mmc_host));
+	if (!host)
+		return -ENOMEM;
+	memset(host, 0, sizeof(*host));
+
+	host->base = (struct sdi_registers *)CFG_MMC_BASE;
+	sdi_u32 = 0xBF;
+	writel(sdi_u32, &host->base->power);
+	host->pwr_init = 0xBF;
+	host->clkdiv_init = SDI_CLKCR_CLKDIV_INIT_V2 |
+				 SDI_CLKCR_CLKEN | SDI_CLKCR_HWFC_EN;
+	strcpy(host->name, "MMC");
+	host->caps = MMC_MODE_8BIT;
+	host->b_max = 0;
+	host->voltages = VOLTAGE_WINDOW_SD;
+	host->clock_min = ARM_MCLK / (2 + SDI_CLKCR_CLKDIV_INIT_V2);
+	host->clock_max = ARM_MCLK / 2;
+	host->clock_in = ARM_MCLK;
+	host->version2 = 1;
+
+	return arm_pl180_mmci_init(host);
+}
+
+/*
+ * board_mmc_init - initialize all the mmc/sd host controllers.
+ * Called by generic mmc framework.
+ */
+int board_mmc_init(bd_t *bis)
+{
+	int error;
+
+	(void) bis;
+
+	error = emmc_host_init();
+	if (error) {
+		printf("emmc_host_init() %d\n", error);
+		return -1;
+	}
+
 	u8500_mmc_power_init();
-#endif /* CONFIG_MMC */
+
+	error = mmc_host_init();
+	if (error) {
+		printf("mmc_host_init() %d\n", error);
+		return -1;
+	}
 
 	return 0;
 }
+#endif /* CONFIG_MMC */

board/st-ericsson/u8500/u8500_href.c

@@ -18,6 +18,7 @@
 
 #include <config.h>
 #include <common.h>
+#include <malloc.h>
 #include <i2c.h>
 #include <asm/types.h>
 #include <asm/io.h>
@@ -374,12 +375,27 @@ static int u8500_mmci_board_init(void)
 
 int board_mmc_init(bd_t *bd)
 {
+	struct pl180_mmc_host *host;
+
 	if (u8500_mmci_board_init())
 		return -ENODEV;
 
-	if (arm_pl180_mmci_init())
-		return -ENODEV;
-	return 0;
+	host = malloc(sizeof(struct pl180_mmc_host));
+	if (!host)
+		return -ENOMEM;
+	memset(host, 0, sizeof(*host));
+
+	strcpy(host->name, "MMC");
+	host->base = (struct sdi_registers *)CONFIG_ARM_PL180_MMCI_BASE;
+	host->pwr_init = INIT_PWR;
+	host->clkdiv_init = SDI_CLKCR_CLKDIV_INIT_V1 | SDI_CLKCR_CLKEN;
+	host->voltages = VOLTAGE_WINDOW_MMC;
+	host->caps = 0;
+	host->clock_in = ARM_MCLK;
+	host->clock_min = ARM_MCLK / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 + 1));
+	host->clock_max = CONFIG_ARM_PL180_MMCI_CLOCK_FREQ;
+
+	return arm_pl180_mmci_init(host);
 }
 #endif
 

drivers/mmc/arm_pl180_mmci.c

@@ -32,14 +32,10 @@
 #include "arm_pl180_mmci.h"
 #include <malloc.h>
 
-struct mmc_host {
-	struct sdi_registers *base;
-};
-
 static int wait_for_command_end(struct mmc *dev, struct mmc_cmd *cmd)
 {
 	u32 hoststatus, statusmask;
-	struct mmc_host *host = dev->priv;
+	struct pl180_mmc_host *host = dev->priv;
 
 	statusmask = SDI_STA_CTIMEOUT | SDI_STA_CCRCFAIL;
 	if ((cmd->resp_type & MMC_RSP_PRESENT))
@@ -53,8 +49,8 @@ static int wait_for_command_end(struct mmc *dev, struct mmc_cmd *cmd)
 
 	writel(statusmask, &host->base->status_clear);
 	if (hoststatus & SDI_STA_CTIMEOUT) {
-		printf("CMD%d time out\n", cmd->cmdidx);
-		return -ETIMEDOUT;
+		debug("CMD%d time out\n", cmd->cmdidx);
+		return TIMEOUT;
 	} else if ((hoststatus & SDI_STA_CCRCFAIL) &&
 		   (cmd->flags & MMC_RSP_CRC)) {
 		printf("CMD%d CRC error\n", cmd->cmdidx);
@@ -80,7 +76,7 @@ static int do_command(struct mmc *dev, struct mmc_cmd *cmd)
 {
 	int result;
 	u32 sdi_cmd = 0;
-	struct mmc_host *host = dev->priv;
+	struct pl180_mmc_host *host = dev->priv;
 
 	sdi_cmd = ((cmd->cmdidx & SDI_CMD_CMDINDEX_MASK) | SDI_CMD_CPSMEN);
 
@@ -112,7 +108,7 @@ static int read_bytes(struct mmc *dev, u32 *dest, u32 blkcount, u32 blksize)
 {
 	u32 *tempbuff = dest;
 	u64 xfercount = blkcount * blksize;
-	struct mmc_host *host = dev->priv;
+	struct pl180_mmc_host *host = dev->priv;
 	u32 status, status_err;
 
 	debug("read_bytes: blkcount=%u blksize=%u\n", blkcount, blksize);
@@ -168,7 +164,7 @@ static int write_bytes(struct mmc *dev, u32 *src, u32 blkcount, u32 blksize)
 	u32 *tempbuff = src;
 	int i;
 	u64 xfercount = blkcount * blksize;
-	struct mmc_host *host = dev->priv;
+	struct pl180_mmc_host *host = dev->priv;
 	u32 status, status_err;
 
 	debug("write_bytes: blkcount=%u blksize=%u\n", blkcount, blksize);
@@ -227,14 +223,19 @@ static int do_data_transfer(struct mmc *dev,
 			    struct mmc_data *data)
 {
 	int error = -ETIMEDOUT;
-	struct mmc_host *host = dev->priv;
+	struct pl180_mmc_host *host = dev->priv;
 	u32 blksz = 0;
 	u32 data_ctrl = 0;
 	u32 data_len = (u32) (data->blocks * data->blocksize);
 
-	blksz = (ffs(data->blocksize) - 1);
-	data_ctrl |= ((blksz << 4) & SDI_DCTRL_DBLKSIZE_MASK);
-	data_ctrl |= SDI_DCTRL_DTEN;
+	if (!host->version2) {
+		blksz = (ffs(data->blocksize) - 1);
+		data_ctrl |= ((blksz << 4) & SDI_DCTRL_DBLKSIZE_MASK);
+	} else {
+		blksz = data->blocksize;
+		data_ctrl |= (blksz << SDI_DCTRL_DBLOCKSIZE_V2_SHIFT);
+	}
+	data_ctrl |= SDI_DCTRL_DTEN | SDI_DCTRL_BUSYMODE;
 
 	writel(SDI_DTIMER_DEFAULT, &host->base->datatimer);
 	writel(data_len, &host->base->datalength);
@@ -257,7 +258,7 @@ static int do_data_transfer(struct mmc *dev,
 
 		writel(data_ctrl, &host->base->datactrl);
 		error = write_bytes(dev, (u32 *)data->src, (u32)data->blocks,
-				    (u32)data->blocksize);
+							(u32)data->blocksize);
 	}
 
 	return error;
@@ -280,17 +281,16 @@ static int host_request(struct mmc *dev,
 /* MMC uses open drain drivers in the enumeration phase */
 static int mmc_host_reset(struct mmc *dev)
 {
-	struct mmc_host *host = dev->priv;
-	u32 sdi_u32 = SDI_PWR_OPD | SDI_PWR_PWRCTRL_ON;
+	struct pl180_mmc_host *host = dev->priv;
 
-	writel(sdi_u32, &host->base->power);
+	writel(host->pwr_init, &host->base->power);
 
 	return 0;
 }
 
 static void host_set_ios(struct mmc *dev)
 {
-	struct mmc_host *host = dev->priv;
+	struct pl180_mmc_host *host = dev->priv;
 	u32 sdi_clkcr;
 
 	sdi_clkcr = readl(&host->base->clock);
@@ -298,15 +298,26 @@ static void host_set_ios(struct mmc *dev)
 	/* Ramp up the clock rate */
 	if (dev->clock) {
 		u32 clkdiv = 0;
+		u32 tmp_clock;
 
-		if (dev->clock >= dev->f_max)
+		if (dev->clock >= dev->f_max) {
+			clkdiv = 0;
 			dev->clock = dev->f_max;
+		} else {
+			clkdiv = (host->clock_in / dev->clock) - 2;
+		}
 
-		clkdiv = ((ARM_MCLK / dev->clock) / 2) - 1;
+		tmp_clock = host->clock_in / (clkdiv + 2);
+		while (tmp_clock > dev->clock) {
+			clkdiv++;
+			tmp_clock = host->clock_in / (clkdiv + 2);
+		}
 
 		if (clkdiv > SDI_CLKCR_CLKDIV_MASK)
 			clkdiv = SDI_CLKCR_CLKDIV_MASK;
 
+		tmp_clock = host->clock_in / (clkdiv + 2);
+		dev->clock = tmp_clock;
 		sdi_clkcr &= ~(SDI_CLKCR_CLKDIV_MASK);
 		sdi_clkcr |= clkdiv;
 	}
@@ -322,8 +333,11 @@ static void host_set_ios(struct mmc *dev)
 		case 4:
 			buswidth |= SDI_CLKCR_WIDBUS_4;
 			break;
+		case 8:
+			buswidth |= SDI_CLKCR_WIDBUS_8;
+			break;
 		default:
-			printf("Invalid bus width\n");
+			printf("Invalid bus width: %d\n", dev->bus_width);
 			break;
 		}
 		sdi_clkcr &= ~(SDI_CLKCR_WIDBUS_MASK);
@@ -334,83 +348,40 @@ static void host_set_ios(struct mmc *dev)
 	udelay(CLK_CHANGE_DELAY);
 }
 
-struct mmc *alloc_mmc_struct(void)
-{
-	struct mmc_host *host = NULL;
-	struct mmc *mmc_device = NULL;
-
-	host = malloc(sizeof(struct mmc_host));
-	if (!host)
-		return NULL;
-
-	mmc_device = malloc(sizeof(struct mmc));
-	if (!mmc_device)
-		goto err;
-
-	mmc_device->priv = host;
-	return mmc_device;
-
-err:
-	free(host);
-	return NULL;
-}
-
 /*
  * mmc_host_init - initialize the mmc controller.
  * Set initial clock and power for mmc slot.
  * Initialize mmc struct and register with mmc framework.
  */
-static int arm_pl180_mmci_host_init(struct mmc *dev)
+int arm_pl180_mmci_init(struct pl180_mmc_host *host)
 {
-	struct mmc_host *host = dev->priv;
+	struct mmc *dev;
 	u32 sdi_u32;
 
-	host->base = (struct sdi_registers *)CONFIG_ARM_PL180_MMCI_BASE;
+	dev = malloc(sizeof(struct mmc));
+	if (!dev)
+		return -ENOMEM;
 
-	/* Initially set power-on, full voltage & MMCI read */
-	sdi_u32 = INIT_PWR;
-	writel(sdi_u32, &host->base->power);
+	memset(dev, 0, sizeof(struct mmc));
+	dev->priv = host;
 
-	/* setting clk freq 505KHz */
-	sdi_u32 = SDI_CLKCR_CLKDIV_INIT | SDI_CLKCR_CLKEN;
-	writel(sdi_u32, &host->base->clock);
+	writel(host->pwr_init, &host->base->power);
+	writel(host->clkdiv_init, &host->base->clock);
 	udelay(CLK_CHANGE_DELAY);
 
 	/* Disable mmc interrupts */
 	sdi_u32 = readl(&host->base->mask0) & ~SDI_MASK0_MASK;
 	writel(sdi_u32, &host->base->mask0);
-
-	sprintf(dev->name, "MMC");
-	dev->clock = ARM_MCLK / (2 * (SDI_CLKCR_CLKDIV_INIT + 1));
+	strncpy(dev->name, host->name, sizeof(dev->name));
 	dev->send_cmd = host_request;
 	dev->set_ios = host_set_ios;
 	dev->init = mmc_host_reset;
 	dev->getcd = NULL;
-	dev->host_caps = 0;
-	dev->voltages = VOLTAGE_WINDOW_MMC;
-	dev->f_min = dev->clock;
-	dev->f_max = CONFIG_ARM_PL180_MMCI_CLOCK_FREQ;
-
-	return 0;
-}
-
-int arm_pl180_mmci_init(void)
-{
-	int error;
-	struct mmc *dev;
-
-	dev = alloc_mmc_struct();
-	if (!dev)
-		return -1;
-
-	error = arm_pl180_mmci_host_init(dev);
-	if (error) {
-		printf("mmci_host_init error - %d\n", error);
-		return -1;
-	}
-
-	dev->b_max = 0;
-
+	dev->host_caps = host->caps;
+	dev->voltages = host->voltages;
+	dev->f_min = host->clock_min;
+	dev->f_max = host->clock_max;
+	dev->b_max = host->b_max;
 	mmc_register(dev);
 	debug("registered mmc interface number is:%d\n", dev->block_dev.dev);
 

drivers/mmc/arm_pl180_mmci.h

@@ -26,8 +26,6 @@
 #ifndef __ARM_PL180_MMCI_H__
 #define __ARM_PL180_MMCI_H__
 
-int arm_pl180_mmci_init(void);
-
 #define COMMAND_REG_DELAY	300
 #define DATA_REG_DELAY		1000
 #define CLK_CHANGE_DELAY	2000
@@ -59,8 +57,13 @@ int arm_pl180_mmci_init(void);
 #define SDI_CLKCR_WIDBUS_MASK	0x00001800
 #define SDI_CLKCR_WIDBUS_1	0x00000000
 #define SDI_CLKCR_WIDBUS_4	0x00000800
+/* V2 only */
+#define SDI_CLKCR_WIDBUS_8	0x00001000
+#define SDI_CLKCR_NEDGE		0x00002000
+#define SDI_CLKCR_HWFC_EN	0x00004000
 
-#define SDI_CLKCR_CLKDIV_INIT	0x000000C6 /* MCLK/(2*(0xC6+1)) => 505KHz */
+#define SDI_CLKCR_CLKDIV_INIT_V1 0x000000C6 /* MCLK/(2*(0xC6+1)) => 505KHz */
+#define SDI_CLKCR_CLKDIV_INIT_V2 0x000000FD
 
 /* SDI command register bits */
 #define SDI_CMD_CMDINDEX_MASK	0x000000FF
@@ -144,6 +147,8 @@ int arm_pl180_mmci_init(void);
 #define SDI_DCTRL_DBOOTMODEEN	0x00002000
 #define SDI_DCTRL_BUSYMODE	0x00004000
 #define SDI_DCTRL_DDR_MODE	0x00008000
+#define SDI_DCTRL_DBLOCKSIZE_V2_MASK   0x7fff0000
+#define SDI_DCTRL_DBLOCKSIZE_V2_SHIFT  16
 
 #define SDI_FIFO_BURST_SIZE	8
 
@@ -180,4 +185,20 @@ struct sdi_registers {
 	u32 pcell_id3;		/* 0xFFC*/
 };
 
+struct pl180_mmc_host {
+	struct sdi_registers *base;
+	char name[32];
+	unsigned int b_max;
+	unsigned int voltages;
+	unsigned int caps;
+	unsigned int clock_in;
+	unsigned int clock_min;
+	unsigned int clock_max;
+	unsigned int clkdiv_init;
+	unsigned int pwr_init;
+	int version2;
+};
+
+int arm_pl180_mmci_init(struct pl180_mmc_host *);
+
 #endif

include/configs/snowball.h

@@ -228,6 +228,14 @@
 #define CONFIG_SYS_TEXT_BASE            0x0
 #endif
 
+/*
+ * MMC related configs
+ */
+#define CONFIG_ARM_PL180_MMCI
+#define MMC_BLOCK_SIZE			512
+#define CFG_EMMC_BASE                   0x80114000
+#define CFG_MMC_BASE                    0x80126000
+
 /*
  * FLASH and environment organization
  */