Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  ARM1136: Fix cache range checks
  mx6: Make pad name macro consistent with the datasheet
  mx28: Fix elftosb source link in README.mx28_common
  doc: README.mx28_common: Add missing entry into Contents

Signed-off-by: Wolfgang Denk <wd@denx.de>

arch/arm/cpu/arm1136/cpu.c

@@ -95,7 +95,7 @@ void flush_dcache_all(void)
 	asm volatile("mcr p15, 0, %0, c7, c10, 4" : : "r" (0));
 }
 
-static inline int bad_cache_range(unsigned long start, unsigned long stop)
+static int check_cache_range(unsigned long start, unsigned long stop)
 {
 	int ok = 1;
 
@@ -114,7 +114,7 @@ static inline int bad_cache_range(unsigned long start, unsigned long stop)
 
 void invalidate_dcache_range(unsigned long start, unsigned long stop)
 {
-	if (bad_cache_range(start, stop))
+	if (!check_cache_range(start, stop))
 		return;
 
 	while (start < stop) {
@@ -125,7 +125,7 @@ void invalidate_dcache_range(unsigned long start, unsigned long stop)
 
 void flush_dcache_range(unsigned long start, unsigned long stop)
 {
-	if (bad_cache_range(start, stop))
+	if (!check_cache_range(start, stop))
 		return;
 
 	while (start < stop) {

arch/arm/include/asm/arch-mx6/mx6x_pins.h

@@ -530,8 +530,8 @@ enum {
 	MX6Q_PAD_EIM_BCLK__IPU1_DI1_PIN16	= IOMUX_PAD(0x046C, 0x0158, 1, 0x0000, 0, 0),
 	MX6Q_PAD_EIM_BCLK__GPIO_6_31		= IOMUX_PAD(0x046C, 0x0158, 5, 0x0000, 0, 0),
 	MX6Q_PAD_EIM_BCLK__TPSMP_HDATA_31	= IOMUX_PAD(0x046C, 0x0158, 6, 0x0000, 0, 0),
-	MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
-	MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 1, 0x0000, 0, 0),
+	MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
+	MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 1, 0x0000, 0, 0),
 	MX6Q_PAD_DI0_DISP_CLK__MIPI_CR_DPY_OT28 = IOMUX_PAD(0x0470, 0x015C, 3, 0x0000, 0, 0),
 	MX6Q_PAD_DI0_DISP_CLK__SDMA_DBG_CR_STA0 = IOMUX_PAD(0x0470, 0x015C, 4, 0x0000, 0, 0),
 	MX6Q_PAD_DI0_DISP_CLK__GPIO_4_16	= IOMUX_PAD(0x0470, 0x015C, 5, 0x0000, 0, 0),

doc/README.mx28_common

@@ -19,6 +19,7 @@ Contents
 1) Prerequisites
 2) Compiling U-Boot for a MX28 based board
 3) Installation of U-Boot for a MX28 based board to SD card
+4) Installation of U-Boot into NAND flash
 
 1) Prerequisites
 ----------------
@@ -29,14 +30,14 @@ is the "mxsboot" tool found in U-Boot source tree.
 
 Firstly, obtain the elftosb archive from the following location:
 
-	http://foss.doredevelopment.dk/mirrors/imx/elftosb-10.12.01.tar.gz
+	ftp://ftp.denx.de/pub/tools/elftosb-10.12.01.tar.gz
 
 We use a $VER variable here to denote the current version. At the time of
 writing of this document, that is "10.12.01". To obtain the file from command
 line, use:
 
 	$ VER="10.12.01"
-	$ wget http://foss.doredevelopment.dk/mirrors/imx/elftosb-${VER}.tar.gz
+	$ wget ftp://ftp.denx.de/pub/tools/elftosb-${VER}.tar.gz
 
 Extract the file:
 
@@ -146,8 +147,8 @@ NOTE: If the user needs to adjust the start sector, the "mxsboot" tool contains
       a "-p" switch for that purpose. The "-p" switch takes the sector number as
       an argument.
 
-4) Installation of U-Boot for NAND flash
------------------------------------------------
+4) Installation of U-Boot into NAND flash
+-----------------------------------------
 
 To boot a MX28 based board from NAND, set the boot mode DIP switches according to i.MX28
 manual chapter 12.2.1 (Table 12-2), PORT=GPMI, NAND 1.8 V.