linux-vybrid_public/drivers/net/bnx2x/bnx2x_link.c

/* Copyright 2008-2011 Broadcom Corporation
 *
 * Unless you and Broadcom execute a separate written software license
 * agreement governing use of this software, this software is licensed to you
 * under the terms of the GNU General Public License version 2, available
 * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL").
 *
 * Notwithstanding the above, under no circumstances may you combine this
 * software in any way with any other Broadcom software provided under a
 * license other than the GPL, without Broadcom's express prior written
 * consent.
 *
 * Written by Yaniv Rosner
 *
 */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/pci.h>
#include <linux/netdevice.h>
#include <linux/delay.h>
#include <linux/ethtool.h>
#include <linux/mutex.h>

#include "bnx2x.h"

/********************************************************/
#define ETH_HLEN			14
/* L2 header size + 2*VLANs (8 bytes) + LLC SNAP (8 bytes) */
#define ETH_OVREHEAD			(ETH_HLEN + 8 + 8)
#define ETH_MIN_PACKET_SIZE		60
#define ETH_MAX_PACKET_SIZE		1500
#define ETH_MAX_JUMBO_PACKET_SIZE	9600
#define MDIO_ACCESS_TIMEOUT		1000
#define BMAC_CONTROL_RX_ENABLE		2

/***********************************************************/
/*			Shortcut definitions		   */
/***********************************************************/

#define NIG_LATCH_BC_ENABLE_MI_INT 0

#define NIG_STATUS_EMAC0_MI_INT \
		NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT
#define NIG_STATUS_XGXS0_LINK10G \
		NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G
#define NIG_STATUS_XGXS0_LINK_STATUS \
		NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS
#define NIG_STATUS_XGXS0_LINK_STATUS_SIZE \
		NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS_SIZE
#define NIG_STATUS_SERDES0_LINK_STATUS \
		NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS
#define NIG_MASK_MI_INT \
		NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT
#define NIG_MASK_XGXS0_LINK10G \
		NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G
#define NIG_MASK_XGXS0_LINK_STATUS \
		NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK_STATUS
#define NIG_MASK_SERDES0_LINK_STATUS \
		NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS

#define MDIO_AN_CL73_OR_37_COMPLETE \
		(MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | \
		 MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE)

#define XGXS_RESET_BITS \
	(MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW |   \
	 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_IDDQ |      \
	 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN |    \
	 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN_SD | \
	 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB)

#define SERDES_RESET_BITS \
	(MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_RSTB_HW | \
	 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ |    \
	 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN |  \
	 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN_SD)

#define AUTONEG_CL37		SHARED_HW_CFG_AN_ENABLE_CL37
#define AUTONEG_CL73		SHARED_HW_CFG_AN_ENABLE_CL73
#define AUTONEG_BAM		SHARED_HW_CFG_AN_ENABLE_BAM
#define AUTONEG_PARALLEL \
				SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION
#define AUTONEG_SGMII_FIBER_AUTODET \
				SHARED_HW_CFG_AN_EN_SGMII_FIBER_AUTO_DETECT
#define AUTONEG_REMOTE_PHY	SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY

#define GP_STATUS_PAUSE_RSOLUTION_TXSIDE \
			MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE
#define GP_STATUS_PAUSE_RSOLUTION_RXSIDE \
			MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE
#define GP_STATUS_SPEED_MASK \
			MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK
#define GP_STATUS_10M	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M
#define GP_STATUS_100M	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M
#define GP_STATUS_1G	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G
#define GP_STATUS_2_5G	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G
#define GP_STATUS_5G	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G
#define GP_STATUS_6G	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G
#define GP_STATUS_10G_HIG \
			MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG
#define GP_STATUS_10G_CX4 \
			MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4
#define GP_STATUS_12G_HIG \
			MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG
#define GP_STATUS_12_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G
#define GP_STATUS_13G	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G
#define GP_STATUS_15G	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G
#define GP_STATUS_16G	MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G
#define GP_STATUS_1G_KX MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX
#define GP_STATUS_10G_KX4 \
			MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4

#define LINK_10THD		LINK_STATUS_SPEED_AND_DUPLEX_10THD
#define LINK_10TFD		LINK_STATUS_SPEED_AND_DUPLEX_10TFD
#define LINK_100TXHD		LINK_STATUS_SPEED_AND_DUPLEX_100TXHD
#define LINK_100T4		LINK_STATUS_SPEED_AND_DUPLEX_100T4
#define LINK_100TXFD		LINK_STATUS_SPEED_AND_DUPLEX_100TXFD
#define LINK_1000THD		LINK_STATUS_SPEED_AND_DUPLEX_1000THD
#define LINK_1000TFD		LINK_STATUS_SPEED_AND_DUPLEX_1000TFD
#define LINK_1000XFD		LINK_STATUS_SPEED_AND_DUPLEX_1000XFD
#define LINK_2500THD		LINK_STATUS_SPEED_AND_DUPLEX_2500THD
#define LINK_2500TFD		LINK_STATUS_SPEED_AND_DUPLEX_2500TFD
#define LINK_2500XFD		LINK_STATUS_SPEED_AND_DUPLEX_2500XFD
#define LINK_10GTFD		LINK_STATUS_SPEED_AND_DUPLEX_10GTFD
#define LINK_10GXFD		LINK_STATUS_SPEED_AND_DUPLEX_10GXFD
#define LINK_12GTFD		LINK_STATUS_SPEED_AND_DUPLEX_12GTFD
#define LINK_12GXFD		LINK_STATUS_SPEED_AND_DUPLEX_12GXFD
#define LINK_12_5GTFD		LINK_STATUS_SPEED_AND_DUPLEX_12_5GTFD
#define LINK_12_5GXFD		LINK_STATUS_SPEED_AND_DUPLEX_12_5GXFD
#define LINK_13GTFD		LINK_STATUS_SPEED_AND_DUPLEX_13GTFD
#define LINK_13GXFD		LINK_STATUS_SPEED_AND_DUPLEX_13GXFD
#define LINK_15GTFD		LINK_STATUS_SPEED_AND_DUPLEX_15GTFD
#define LINK_15GXFD		LINK_STATUS_SPEED_AND_DUPLEX_15GXFD
#define LINK_16GTFD		LINK_STATUS_SPEED_AND_DUPLEX_16GTFD
#define LINK_16GXFD		LINK_STATUS_SPEED_AND_DUPLEX_16GXFD

#define PHY_XGXS_FLAG			0x1
#define PHY_SGMII_FLAG			0x2
#define PHY_SERDES_FLAG			0x4

/* */
#define SFP_EEPROM_CON_TYPE_ADDR		0x2
	#define SFP_EEPROM_CON_TYPE_VAL_LC	0x7
	#define SFP_EEPROM_CON_TYPE_VAL_COPPER	0x21


#define SFP_EEPROM_COMP_CODE_ADDR		0x3
	#define SFP_EEPROM_COMP_CODE_SR_MASK	(1<<4)
	#define SFP_EEPROM_COMP_CODE_LR_MASK	(1<<5)
	#define SFP_EEPROM_COMP_CODE_LRM_MASK	(1<<6)

#define SFP_EEPROM_FC_TX_TECH_ADDR		0x8
	#define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4
	#define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE  0x8

#define SFP_EEPROM_OPTIONS_ADDR			0x40
	#define SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK 0x1
#define SFP_EEPROM_OPTIONS_SIZE			2

#define EDC_MODE_LINEAR				0x0022
#define EDC_MODE_LIMITING				0x0044
#define EDC_MODE_PASSIVE_DAC			0x0055


#define ETS_BW_LIMIT_CREDIT_UPPER_BOUND		(0x5000)
#define ETS_BW_LIMIT_CREDIT_WEIGHT		(0x5000)
/**********************************************************/
/*                     INTERFACE                          */
/**********************************************************/

#define CL22_WR_OVER_CL45(_bp, _phy, _bank, _addr, _val) \
	bnx2x_cl45_write(_bp, _phy, \
		(_phy)->def_md_devad, \
		(_bank + (_addr & 0xf)), \
		_val)

#define CL22_RD_OVER_CL45(_bp, _phy, _bank, _addr, _val) \
	bnx2x_cl45_read(_bp, _phy, \
		(_phy)->def_md_devad, \
		(_bank + (_addr & 0xf)), \
		_val)

static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits)
{
	u32 val = REG_RD(bp, reg);

	val |= bits;
	REG_WR(bp, reg, val);
	return val;
}

static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits)
{
	u32 val = REG_RD(bp, reg);

	val &= ~bits;
	REG_WR(bp, reg, val);
	return val;
}

/******************************************************************/
/*				ETS section			  */
/******************************************************************/
void bnx2x_ets_disabled(struct link_params *params)
{
	/* ETS disabled configuration*/
	struct bnx2x *bp = params->bp;

	DP(NETIF_MSG_LINK, "ETS disabled configuration\n");

	/*
	 * mapping between entry  priority to client number (0,1,2 -debug and
	 * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST)
	 * 3bits client num.
	 *   PRI4    |    PRI3    |    PRI2    |    PRI1    |    PRI0
	 * cos1-100     cos0-011     dbg1-010     dbg0-001     MCP-000
	 */

	REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, 0x4688);
	/*
	 * Bitmap of 5bits length. Each bit specifies whether the entry behaves
	 * as strict.  Bits 0,1,2 - debug and management entries, 3 -
	 * COS0 entry, 4 - COS1 entry.
	 * COS1 | COS0 | DEBUG1 | DEBUG0 | MGMT
	 * bit4   bit3	  bit2   bit1	  bit0
	 * MCP and debug are strict
	 */

	REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7);
	/* defines which entries (clients) are subjected to WFQ arbitration */
	REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0);
	/*
	 * For strict priority entries defines the number of consecutive
	 * slots for the highest priority.
	 */
	REG_WR(bp, NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100);
	/*
	 * mapping between the CREDIT_WEIGHT registers and actual client
	 * numbers
	 */
	REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP, 0);
	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, 0);
	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, 0);

	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0, 0);
	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1, 0);
	REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, 0);
	/* ETS mode disable */
	REG_WR(bp, PBF_REG_ETS_ENABLED, 0);
	/*
	 * If ETS mode is enabled (there is no strict priority) defines a WFQ
	 * weight for COS0/COS1.
	 */
	REG_WR(bp, PBF_REG_COS0_WEIGHT, 0x2710);
	REG_WR(bp, PBF_REG_COS1_WEIGHT, 0x2710);
	/* Upper bound that COS0_WEIGHT can reach in the WFQ arbiter */
	REG_WR(bp, PBF_REG_COS0_UPPER_BOUND, 0x989680);
	REG_WR(bp, PBF_REG_COS1_UPPER_BOUND, 0x989680);
	/* Defines the number of consecutive slots for the strict priority */
	REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0);
}

static void bnx2x_ets_bw_limit_common(const struct link_params *params)
{
	/* ETS disabled configuration */
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "ETS enabled BW limit configuration\n");
	/*
	 * defines which entries (clients) are subjected to WFQ arbitration
	 * COS0 0x8
	 * COS1 0x10
	 */
	REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0x18);
	/*
	 * mapping between the ARB_CREDIT_WEIGHT registers and actual
	 * client numbers (WEIGHT_0 does not actually have to represent
	 * client 0)
	 *    PRI4    |    PRI3    |    PRI2    |    PRI1    |    PRI0
	 *  cos1-001     cos0-000     dbg1-100     dbg0-011     MCP-010
	 */
	REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP, 0x111A);

	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0,
	       ETS_BW_LIMIT_CREDIT_UPPER_BOUND);
	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1,
	       ETS_BW_LIMIT_CREDIT_UPPER_BOUND);

	/* ETS mode enabled*/
	REG_WR(bp, PBF_REG_ETS_ENABLED, 1);

	/* Defines the number of consecutive slots for the strict priority */
	REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0);
	/*
	 * Bitmap of 5bits length. Each bit specifies whether the entry behaves
	 * as strict.  Bits 0,1,2 - debug and management entries, 3 - COS0
	 * entry, 4 - COS1 entry.
	 * COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT
	 * bit4   bit3	  bit2     bit1	   bit0
	 * MCP and debug are strict
	 */
	REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7);

	/* Upper bound that COS0_WEIGHT can reach in the WFQ arbiter.*/
	REG_WR(bp, PBF_REG_COS0_UPPER_BOUND,
	       ETS_BW_LIMIT_CREDIT_UPPER_BOUND);
	REG_WR(bp, PBF_REG_COS1_UPPER_BOUND,
	       ETS_BW_LIMIT_CREDIT_UPPER_BOUND);
}

void bnx2x_ets_bw_limit(const struct link_params *params, const u32 cos0_bw,
			const u32 cos1_bw)
{
	/* ETS disabled configuration*/
	struct bnx2x *bp = params->bp;
	const u32 total_bw = cos0_bw + cos1_bw;
	u32 cos0_credit_weight = 0;
	u32 cos1_credit_weight = 0;

	DP(NETIF_MSG_LINK, "ETS enabled BW limit configuration\n");

	if ((0 == total_bw) ||
	    (0 == cos0_bw) ||
	    (0 == cos1_bw)) {
		DP(NETIF_MSG_LINK, "Total BW can't be zero\n");
		return;
	}

	cos0_credit_weight = (cos0_bw * ETS_BW_LIMIT_CREDIT_WEIGHT)/
		total_bw;
	cos1_credit_weight = (cos1_bw * ETS_BW_LIMIT_CREDIT_WEIGHT)/
		total_bw;

	bnx2x_ets_bw_limit_common(params);

	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, cos0_credit_weight);
	REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, cos1_credit_weight);

	REG_WR(bp, PBF_REG_COS0_WEIGHT, cos0_credit_weight);
	REG_WR(bp, PBF_REG_COS1_WEIGHT, cos1_credit_weight);
}

int bnx2x_ets_strict(const struct link_params *params, const u8 strict_cos)
{
	/* ETS disabled configuration*/
	struct bnx2x *bp = params->bp;
	u32 val	= 0;

	DP(NETIF_MSG_LINK, "ETS enabled strict configuration\n");
	/*
	 * Bitmap of 5bits length. Each bit specifies whether the entry behaves
	 * as strict.  Bits 0,1,2 - debug and management entries,
	 * 3 - COS0 entry, 4 - COS1 entry.
	 *  COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT
	 *  bit4   bit3	  bit2      bit1     bit0
	 * MCP and debug are strict
	 */
	REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x1F);
	/*
	 * For strict priority entries defines the number of consecutive slots
	 * for the highest priority.
	 */
	REG_WR(bp, NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100);
	/* ETS mode disable */
	REG_WR(bp, PBF_REG_ETS_ENABLED, 0);
	/* Defines the number of consecutive slots for the strict priority */
	REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0x100);

	/* Defines the number of consecutive slots for the strict priority */
	REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, strict_cos);

	/*
	 * mapping between entry  priority to client number (0,1,2 -debug and
	 * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST)
	 * 3bits client num.
	 *   PRI4    |    PRI3    |    PRI2    |    PRI1    |    PRI0
	 * dbg0-010     dbg1-001     cos1-100     cos0-011     MCP-000
	 * dbg0-010     dbg1-001     cos0-011     cos1-100     MCP-000
	 */
	val = (0 == strict_cos) ? 0x2318 : 0x22E0;
	REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, val);

	return 0;
}
/******************************************************************/
/*			PFC section				  */
/******************************************************************/

static void bnx2x_bmac2_get_pfc_stat(struct link_params *params,
				     u32 pfc_frames_sent[2],
				     u32 pfc_frames_received[2])
{
	/* Read pfc statistic */
	struct bnx2x *bp = params->bp;
	u32 bmac_addr = params->port ? NIG_REG_INGRESS_BMAC1_MEM :
		NIG_REG_INGRESS_BMAC0_MEM;

	DP(NETIF_MSG_LINK, "pfc statistic read from BMAC\n");

	REG_RD_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_STAT_GTPP,
					pfc_frames_sent, 2);

	REG_RD_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_STAT_GRPP,
					pfc_frames_received, 2);

}
static void bnx2x_emac_get_pfc_stat(struct link_params *params,
				    u32 pfc_frames_sent[2],
				    u32 pfc_frames_received[2])
{
	/* Read pfc statistic */
	struct bnx2x *bp = params->bp;
	u32 emac_base = params->port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
	u32 val_xon = 0;
	u32 val_xoff = 0;

	DP(NETIF_MSG_LINK, "pfc statistic read from EMAC\n");

	/* PFC received frames */
	val_xoff = REG_RD(bp, emac_base +
				EMAC_REG_RX_PFC_STATS_XOFF_RCVD);
	val_xoff &= EMAC_REG_RX_PFC_STATS_XOFF_RCVD_COUNT;
	val_xon = REG_RD(bp, emac_base + EMAC_REG_RX_PFC_STATS_XON_RCVD);
	val_xon &= EMAC_REG_RX_PFC_STATS_XON_RCVD_COUNT;

	pfc_frames_received[0] = val_xon + val_xoff;

	/* PFC received sent */
	val_xoff = REG_RD(bp, emac_base +
				EMAC_REG_RX_PFC_STATS_XOFF_SENT);
	val_xoff &= EMAC_REG_RX_PFC_STATS_XOFF_SENT_COUNT;
	val_xon = REG_RD(bp, emac_base + EMAC_REG_RX_PFC_STATS_XON_SENT);
	val_xon &= EMAC_REG_RX_PFC_STATS_XON_SENT_COUNT;

	pfc_frames_sent[0] = val_xon + val_xoff;
}

void bnx2x_pfc_statistic(struct link_params *params, struct link_vars *vars,
			 u32 pfc_frames_sent[2],
			 u32 pfc_frames_received[2])
{
	/* Read pfc statistic */
	struct bnx2x *bp = params->bp;
	u32 val	= 0;
	DP(NETIF_MSG_LINK, "pfc statistic\n");

	if (!vars->link_up)
		return;

	val = REG_RD(bp, MISC_REG_RESET_REG_2);
	if ((val & (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port))
	    == 0) {
		DP(NETIF_MSG_LINK, "About to read stats from EMAC\n");
		bnx2x_emac_get_pfc_stat(params, pfc_frames_sent,
					pfc_frames_received);
	} else {
		DP(NETIF_MSG_LINK, "About to read stats from BMAC\n");
		bnx2x_bmac2_get_pfc_stat(params, pfc_frames_sent,
					 pfc_frames_received);
	}
}
/******************************************************************/
/*			MAC/PBF section				  */
/******************************************************************/
static void bnx2x_emac_init(struct link_params *params,
			    struct link_vars *vars)
{
	/* reset and unreset the emac core */
	struct bnx2x *bp = params->bp;
	u8 port = params->port;
	u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
	u32 val;
	u16 timeout;

	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
	       (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));
	udelay(5);
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
	       (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port));

	/* init emac - use read-modify-write */
	/* self clear reset */
	val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
	EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET));

	timeout = 200;
	do {
		val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
		DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val);
		if (!timeout) {
			DP(NETIF_MSG_LINK, "EMAC timeout!\n");
			return;
		}
		timeout--;
	} while (val & EMAC_MODE_RESET);

	/* Set mac address */
	val = ((params->mac_addr[0] << 8) |
		params->mac_addr[1]);
	EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH, val);

	val = ((params->mac_addr[2] << 24) |
	       (params->mac_addr[3] << 16) |
	       (params->mac_addr[4] << 8) |
		params->mac_addr[5]);
	EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + 4, val);
}

static int bnx2x_emac_enable(struct link_params *params,
			      struct link_vars *vars, u8 lb)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;
	u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
	u32 val;

	DP(NETIF_MSG_LINK, "enabling EMAC\n");

	/* enable emac and not bmac */
	REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 1);

	/* ASIC */
	if (vars->phy_flags & PHY_XGXS_FLAG) {
		u32 ser_lane = ((params->lane_config &
				 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
				PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);

		DP(NETIF_MSG_LINK, "XGXS\n");
		/* select the master lanes (out of 0-3) */
		REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, ser_lane);
		/* select XGXS */
		REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);

	} else { /* SerDes */
		DP(NETIF_MSG_LINK, "SerDes\n");
		/* select SerDes */
		REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0);
	}

	bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
		      EMAC_RX_MODE_RESET);
	bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
		      EMAC_TX_MODE_RESET);

	if (CHIP_REV_IS_SLOW(bp)) {
		/* config GMII mode */
		val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
		EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII));
	} else { /* ASIC */
		/* pause enable/disable */
		bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
			       EMAC_RX_MODE_FLOW_EN);

		bnx2x_bits_dis(bp,  emac_base + EMAC_REG_EMAC_TX_MODE,
			       (EMAC_TX_MODE_EXT_PAUSE_EN |
				EMAC_TX_MODE_FLOW_EN));
		if (!(params->feature_config_flags &
		      FEATURE_CONFIG_PFC_ENABLED)) {
			if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
				bnx2x_bits_en(bp, emac_base +
					      EMAC_REG_EMAC_RX_MODE,
					      EMAC_RX_MODE_FLOW_EN);

			if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
				bnx2x_bits_en(bp, emac_base +
					      EMAC_REG_EMAC_TX_MODE,
					      (EMAC_TX_MODE_EXT_PAUSE_EN |
					       EMAC_TX_MODE_FLOW_EN));
		} else
			bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
				      EMAC_TX_MODE_FLOW_EN);
	}

	/* KEEP_VLAN_TAG, promiscuous */
	val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE);
	val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS;

	/*
	 * Setting this bit causes MAC control frames (except for pause
	 * frames) to be passed on for processing. This setting has no
	 * affect on the operation of the pause frames. This bit effects
	 * all packets regardless of RX Parser packet sorting logic.
	 * Turn the PFC off to make sure we are in Xon state before
	 * enabling it.
	 */
	EMAC_WR(bp, EMAC_REG_RX_PFC_MODE, 0);
	if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) {
		DP(NETIF_MSG_LINK, "PFC is enabled\n");
		/* Enable PFC again */
		EMAC_WR(bp, EMAC_REG_RX_PFC_MODE,
			EMAC_REG_RX_PFC_MODE_RX_EN |
			EMAC_REG_RX_PFC_MODE_TX_EN |
			EMAC_REG_RX_PFC_MODE_PRIORITIES);

		EMAC_WR(bp, EMAC_REG_RX_PFC_PARAM,
			((0x0101 <<
			  EMAC_REG_RX_PFC_PARAM_OPCODE_BITSHIFT) |
			 (0x00ff <<
			  EMAC_REG_RX_PFC_PARAM_PRIORITY_EN_BITSHIFT)));
		val |= EMAC_RX_MODE_KEEP_MAC_CONTROL;
	}
	EMAC_WR(bp, EMAC_REG_EMAC_RX_MODE, val);

	/* Set Loopback */
	val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE);
	if (lb)
		val |= 0x810;
	else
		val &= ~0x810;
	EMAC_WR(bp, EMAC_REG_EMAC_MODE, val);

	/* enable emac */
	REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1);

	/* enable emac for jumbo packets */
	EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE,
		(EMAC_RX_MTU_SIZE_JUMBO_ENA |
		 (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)));

	/* strip CRC */
	REG_WR(bp, NIG_REG_NIG_INGRESS_EMAC0_NO_CRC + port*4, 0x1);

	/* disable the NIG in/out to the bmac */
	REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x0);
	REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, 0x0);
	REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x0);

	/* enable the NIG in/out to the emac */
	REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x1);
	val = 0;
	if ((params->feature_config_flags &
	      FEATURE_CONFIG_PFC_ENABLED) ||
	    (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
		val = 1;

	REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val);
	REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1);

	REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0);

	vars->mac_type = MAC_TYPE_EMAC;
	return 0;
}

static void bnx2x_update_pfc_bmac1(struct link_params *params,
				   struct link_vars *vars)
{
	u32 wb_data[2];
	struct bnx2x *bp = params->bp;
	u32 bmac_addr =  params->port ? NIG_REG_INGRESS_BMAC1_MEM :
		NIG_REG_INGRESS_BMAC0_MEM;

	u32 val = 0x14;
	if ((!(params->feature_config_flags &
	      FEATURE_CONFIG_PFC_ENABLED)) &&
		(vars->flow_ctrl & BNX2X_FLOW_CTRL_RX))
		/* Enable BigMAC to react on received Pause packets */
		val |= (1<<5);
	wb_data[0] = val;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_CONTROL, wb_data, 2);

	/* tx control */
	val = 0xc0;
	if (!(params->feature_config_flags &
	      FEATURE_CONFIG_PFC_ENABLED) &&
		(vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
		val |= 0x800000;
	wb_data[0] = val;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_CONTROL, wb_data, 2);
}

static void bnx2x_update_pfc_bmac2(struct link_params *params,
				   struct link_vars *vars,
				   u8 is_lb)
{
	/*
	 * Set rx control: Strip CRC and enable BigMAC to relay
	 * control packets to the system as well
	 */
	u32 wb_data[2];
	struct bnx2x *bp = params->bp;
	u32 bmac_addr = params->port ? NIG_REG_INGRESS_BMAC1_MEM :
		NIG_REG_INGRESS_BMAC0_MEM;
	u32 val = 0x14;

	if ((!(params->feature_config_flags &
	      FEATURE_CONFIG_PFC_ENABLED)) &&
		(vars->flow_ctrl & BNX2X_FLOW_CTRL_RX))
		/* Enable BigMAC to react on received Pause packets */
		val |= (1<<5);
	wb_data[0] = val;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL, wb_data, 2);
	udelay(30);

	/* Tx control */
	val = 0xc0;
	if (!(params->feature_config_flags &
				FEATURE_CONFIG_PFC_ENABLED) &&
	    (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
		val |= 0x800000;
	wb_data[0] = val;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_CONTROL, wb_data, 2);

	if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) {
		DP(NETIF_MSG_LINK, "PFC is enabled\n");
		/* Enable PFC RX & TX & STATS and set 8 COS  */
		wb_data[0] = 0x0;
		wb_data[0] |= (1<<0);  /* RX */
		wb_data[0] |= (1<<1);  /* TX */
		wb_data[0] |= (1<<2);  /* Force initial Xon */
		wb_data[0] |= (1<<3);  /* 8 cos */
		wb_data[0] |= (1<<5);  /* STATS */
		wb_data[1] = 0;
		REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_PFC_CONTROL,
			    wb_data, 2);
		/* Clear the force Xon */
		wb_data[0] &= ~(1<<2);
	} else {
		DP(NETIF_MSG_LINK, "PFC is disabled\n");
		/* disable PFC RX & TX & STATS and set 8 COS */
		wb_data[0] = 0x8;
		wb_data[1] = 0;
	}

	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_PFC_CONTROL, wb_data, 2);

	/*
	 * Set Time (based unit is 512 bit time) between automatic
	 * re-sending of PP packets amd enable automatic re-send of
	 * Per-Priroity Packet as long as pp_gen is asserted and
	 * pp_disable is low.
	 */
	val = 0x8000;
	if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED)
		val |= (1<<16); /* enable automatic re-send */

	wb_data[0] = val;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_PAUSE_CONTROL,
		    wb_data, 2);

	/* mac control */
	val = 0x3; /* Enable RX and TX */
	if (is_lb) {
		val |= 0x4; /* Local loopback */
		DP(NETIF_MSG_LINK, "enable bmac loopback\n");
	}
	/* When PFC enabled, Pass pause frames towards the NIG. */
	if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED)
		val |= ((1<<6)|(1<<5));

	wb_data[0] = val;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2);
}

static void bnx2x_update_pfc_brb(struct link_params *params,
		struct link_vars *vars,
		struct bnx2x_nig_brb_pfc_port_params *pfc_params)
{
	struct bnx2x *bp = params->bp;
	int set_pfc = params->feature_config_flags &
		FEATURE_CONFIG_PFC_ENABLED;

	/* default - pause configuration */
	u32 pause_xoff_th = PFC_BRB_MAC_PAUSE_XOFF_THRESHOLD_PAUSEABLE;
	u32 pause_xon_th = PFC_BRB_MAC_PAUSE_XON_THRESHOLD_PAUSEABLE;
	u32 full_xoff_th = PFC_BRB_MAC_FULL_XOFF_THRESHOLD_PAUSEABLE;
	u32 full_xon_th = PFC_BRB_MAC_FULL_XON_THRESHOLD_PAUSEABLE;

	if (set_pfc && pfc_params)
		/* First COS */
		if (!pfc_params->cos0_pauseable) {
			pause_xoff_th =
			  PFC_BRB_MAC_PAUSE_XOFF_THRESHOLD_NON_PAUSEABLE;
			pause_xon_th =
			  PFC_BRB_MAC_PAUSE_XON_THRESHOLD_NON_PAUSEABLE;
			full_xoff_th =
			  PFC_BRB_MAC_FULL_XOFF_THRESHOLD_NON_PAUSEABLE;
			full_xon_th =
			  PFC_BRB_MAC_FULL_XON_THRESHOLD_NON_PAUSEABLE;
		}
	/*
	 * The number of free blocks below which the pause signal to class 0
	 * of MAC #n is asserted. n=0,1
	 */
	REG_WR(bp, BRB1_REG_PAUSE_0_XOFF_THRESHOLD_0 , pause_xoff_th);
	/*
	 * The number of free blocks above which the pause signal to class 0
	 * of MAC #n is de-asserted. n=0,1
	 */
	REG_WR(bp, BRB1_REG_PAUSE_0_XON_THRESHOLD_0 , pause_xon_th);
	/*
	 * The number of free blocks below which the full signal to class 0
	 * of MAC #n is asserted. n=0,1
	 */
	REG_WR(bp, BRB1_REG_FULL_0_XOFF_THRESHOLD_0 , full_xoff_th);
	/*
	 * The number of free blocks above which the full signal to class 0
	 * of MAC #n is de-asserted. n=0,1
	 */
	REG_WR(bp, BRB1_REG_FULL_0_XON_THRESHOLD_0 , full_xon_th);

	if (set_pfc && pfc_params) {
		/* Second COS */
		if (pfc_params->cos1_pauseable) {
			pause_xoff_th =
			  PFC_BRB_MAC_PAUSE_XOFF_THRESHOLD_PAUSEABLE;
			pause_xon_th =
			  PFC_BRB_MAC_PAUSE_XON_THRESHOLD_PAUSEABLE;
			full_xoff_th =
			  PFC_BRB_MAC_FULL_XOFF_THRESHOLD_PAUSEABLE;
			full_xon_th =
			  PFC_BRB_MAC_FULL_XON_THRESHOLD_PAUSEABLE;
		} else {
			pause_xoff_th =
			  PFC_BRB_MAC_PAUSE_XOFF_THRESHOLD_NON_PAUSEABLE;
			pause_xon_th =
			  PFC_BRB_MAC_PAUSE_XON_THRESHOLD_NON_PAUSEABLE;
			full_xoff_th =
			  PFC_BRB_MAC_FULL_XOFF_THRESHOLD_NON_PAUSEABLE;
			full_xon_th =
			  PFC_BRB_MAC_FULL_XON_THRESHOLD_NON_PAUSEABLE;
		}
		/*
		 * The number of free blocks below which the pause signal to
		 * class 1 of MAC #n is asserted. n=0,1
		 */
		REG_WR(bp, BRB1_REG_PAUSE_1_XOFF_THRESHOLD_0, pause_xoff_th);
		/*
		 * The number of free blocks above which the pause signal to
		 * class 1 of MAC #n is de-asserted. n=0,1
		 */
		REG_WR(bp, BRB1_REG_PAUSE_1_XON_THRESHOLD_0, pause_xon_th);
		/*
		 * The number of free blocks below which the full signal to
		 * class 1 of MAC #n is asserted. n=0,1
		 */
		REG_WR(bp, BRB1_REG_FULL_1_XOFF_THRESHOLD_0, full_xoff_th);
		/*
		 * The number of free blocks above which the full signal to
		 * class 1 of MAC #n is de-asserted. n=0,1
		 */
		REG_WR(bp, BRB1_REG_FULL_1_XON_THRESHOLD_0, full_xon_th);
	}
}

static void bnx2x_update_pfc_nig(struct link_params *params,
		struct link_vars *vars,
		struct bnx2x_nig_brb_pfc_port_params *nig_params)
{
	u32 xcm_mask = 0, ppp_enable = 0, pause_enable = 0, llfc_out_en = 0;
	u32 llfc_enable = 0, xcm0_out_en = 0, p0_hwpfc_enable = 0;
	u32 pkt_priority_to_cos = 0;
	u32 val;
	struct bnx2x *bp = params->bp;
	int port = params->port;
	int set_pfc = params->feature_config_flags &
		FEATURE_CONFIG_PFC_ENABLED;
	DP(NETIF_MSG_LINK, "updating pfc nig parameters\n");

	/*
	 * When NIG_LLH0_XCM_MASK_REG_LLHX_XCM_MASK_BCN bit is set
	 * MAC control frames (that are not pause packets)
	 * will be forwarded to the XCM.
	 */
	xcm_mask = REG_RD(bp,
				port ? NIG_REG_LLH1_XCM_MASK :
				NIG_REG_LLH0_XCM_MASK);
	/*
	 * nig params will override non PFC params, since it's possible to
	 * do transition from PFC to SAFC
	 */
	if (set_pfc) {
		pause_enable = 0;
		llfc_out_en = 0;
		llfc_enable = 0;
		ppp_enable = 1;
		xcm_mask &= ~(port ? NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN :
				     NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN);
		xcm0_out_en = 0;
		p0_hwpfc_enable = 1;
	} else  {
		if (nig_params) {
			llfc_out_en = nig_params->llfc_out_en;
			llfc_enable = nig_params->llfc_enable;
			pause_enable = nig_params->pause_enable;
		} else  /*defaul non PFC mode - PAUSE */
			pause_enable = 1;

		xcm_mask |= (port ? NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN :
			NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN);
		xcm0_out_en = 1;
	}

	REG_WR(bp, port ? NIG_REG_LLFC_OUT_EN_1 :
	       NIG_REG_LLFC_OUT_EN_0, llfc_out_en);
	REG_WR(bp, port ? NIG_REG_LLFC_ENABLE_1 :
	       NIG_REG_LLFC_ENABLE_0, llfc_enable);
	REG_WR(bp, port ? NIG_REG_PAUSE_ENABLE_1 :
	       NIG_REG_PAUSE_ENABLE_0, pause_enable);

	REG_WR(bp, port ? NIG_REG_PPP_ENABLE_1 :
	       NIG_REG_PPP_ENABLE_0, ppp_enable);

	REG_WR(bp, port ? NIG_REG_LLH1_XCM_MASK :
	       NIG_REG_LLH0_XCM_MASK, xcm_mask);

	REG_WR(bp,  NIG_REG_LLFC_EGRESS_SRC_ENABLE_0, 0x7);

	/* output enable for RX_XCM # IF */
	REG_WR(bp, NIG_REG_XCM0_OUT_EN, xcm0_out_en);

	/* HW PFC TX enable */
	REG_WR(bp, NIG_REG_P0_HWPFC_ENABLE, p0_hwpfc_enable);

	/* 0x2 = BMAC, 0x1= EMAC */
	switch (vars->mac_type) {
	case MAC_TYPE_EMAC:
		val = 1;
		break;
	case MAC_TYPE_BMAC:
		val = 0;
		break;
	default:
		val = 0;
		break;
	}
	REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT, val);

	if (nig_params) {
		pkt_priority_to_cos = nig_params->pkt_priority_to_cos;

		REG_WR(bp, port ? NIG_REG_P1_RX_COS0_PRIORITY_MASK :
		       NIG_REG_P0_RX_COS0_PRIORITY_MASK,
		       nig_params->rx_cos0_priority_mask);

		REG_WR(bp, port ? NIG_REG_P1_RX_COS1_PRIORITY_MASK :
		       NIG_REG_P0_RX_COS1_PRIORITY_MASK,
		       nig_params->rx_cos1_priority_mask);

		REG_WR(bp, port ? NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_1 :
		       NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_0,
		       nig_params->llfc_high_priority_classes);

		REG_WR(bp, port ? NIG_REG_LLFC_LOW_PRIORITY_CLASSES_1 :
		       NIG_REG_LLFC_LOW_PRIORITY_CLASSES_0,
		       nig_params->llfc_low_priority_classes);
	}
	REG_WR(bp, port ? NIG_REG_P1_PKT_PRIORITY_TO_COS :
	       NIG_REG_P0_PKT_PRIORITY_TO_COS,
	       pkt_priority_to_cos);
}


void bnx2x_update_pfc(struct link_params *params,
		      struct link_vars *vars,
		      struct bnx2x_nig_brb_pfc_port_params *pfc_params)
{
	/*
	 * The PFC and pause are orthogonal to one another, meaning when
	 * PFC is enabled, the pause are disabled, and when PFC is
	 * disabled, pause are set according to the pause result.
	 */
	u32 val;
	struct bnx2x *bp = params->bp;

	/* update NIG params */
	bnx2x_update_pfc_nig(params, vars, pfc_params);

	/* update BRB params */
	bnx2x_update_pfc_brb(params, vars, pfc_params);

	if (!vars->link_up)
		return;

	val = REG_RD(bp, MISC_REG_RESET_REG_2);
	if ((val & (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port))
	    == 0) {
		DP(NETIF_MSG_LINK, "About to update PFC in EMAC\n");
		bnx2x_emac_enable(params, vars, 0);
		return;
	}

	DP(NETIF_MSG_LINK, "About to update PFC in BMAC\n");
	if (CHIP_IS_E2(bp))
		bnx2x_update_pfc_bmac2(params, vars, 0);
	else
		bnx2x_update_pfc_bmac1(params, vars);

	val = 0;
	if ((params->feature_config_flags &
	      FEATURE_CONFIG_PFC_ENABLED) ||
	    (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
		val = 1;
	REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + params->port*4, val);
}

static int bnx2x_bmac1_enable(struct link_params *params,
			      struct link_vars *vars,
			      u8 is_lb)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;
	u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
			       NIG_REG_INGRESS_BMAC0_MEM;
	u32 wb_data[2];
	u32 val;

	DP(NETIF_MSG_LINK, "Enabling BigMAC1\n");

	/* XGXS control */
	wb_data[0] = 0x3c;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_XGXS_CONTROL,
		    wb_data, 2);

	/* tx MAC SA */
	wb_data[0] = ((params->mac_addr[2] << 24) |
		       (params->mac_addr[3] << 16) |
		       (params->mac_addr[4] << 8) |
			params->mac_addr[5]);
	wb_data[1] = ((params->mac_addr[0] << 8) |
			params->mac_addr[1]);
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, wb_data, 2);

	/* mac control */
	val = 0x3;
	if (is_lb) {
		val |= 0x4;
		DP(NETIF_MSG_LINK, "enable bmac loopback\n");
	}
	wb_data[0] = val;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, wb_data, 2);

	/* set rx mtu */
	wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, wb_data, 2);

	bnx2x_update_pfc_bmac1(params, vars);

	/* set tx mtu */
	wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, wb_data, 2);

	/* set cnt max size */
	wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, wb_data, 2);

	/* configure safc */
	wb_data[0] = 0x1000200;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS,
		    wb_data, 2);

	return 0;
}

static int bnx2x_bmac2_enable(struct link_params *params,
			      struct link_vars *vars,
			      u8 is_lb)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;
	u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
			       NIG_REG_INGRESS_BMAC0_MEM;
	u32 wb_data[2];

	DP(NETIF_MSG_LINK, "Enabling BigMAC2\n");

	wb_data[0] = 0;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2);
	udelay(30);

	/* XGXS control: Reset phy HW, MDIO registers, PHY PLL and BMAC */
	wb_data[0] = 0x3c;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_XGXS_CONTROL,
		    wb_data, 2);

	udelay(30);

	/* tx MAC SA */
	wb_data[0] = ((params->mac_addr[2] << 24) |
		       (params->mac_addr[3] << 16) |
		       (params->mac_addr[4] << 8) |
			params->mac_addr[5]);
	wb_data[1] = ((params->mac_addr[0] << 8) |
			params->mac_addr[1]);
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_SOURCE_ADDR,
		    wb_data, 2);

	udelay(30);

	/* Configure SAFC */
	wb_data[0] = 0x1000200;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS,
		    wb_data, 2);
	udelay(30);

	/* set rx mtu */
	wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE, wb_data, 2);
	udelay(30);

	/* set tx mtu */
	wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE, wb_data, 2);
	udelay(30);
	/* set cnt max size */
	wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD - 2;
	wb_data[1] = 0;
	REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE, wb_data, 2);
	udelay(30);
	bnx2x_update_pfc_bmac2(params, vars, is_lb);

	return 0;
}

static int bnx2x_bmac_enable(struct link_params *params,
			     struct link_vars *vars,
			     u8 is_lb)
{
	int rc = 0;
	u8 port = params->port;
	struct bnx2x *bp = params->bp;
	u32 val;
	/* reset and unreset the BigMac */
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
	       (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
	msleep(1);

	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
	       (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));

	/* enable access for bmac registers */
	REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);

	/* Enable BMAC according to BMAC type*/
	if (CHIP_IS_E2(bp))
		rc = bnx2x_bmac2_enable(params, vars, is_lb);
	else
		rc = bnx2x_bmac1_enable(params, vars, is_lb);
	REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0x1);
	REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 0x0);
	REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 0x0);
	val = 0;
	if ((params->feature_config_flags &
	      FEATURE_CONFIG_PFC_ENABLED) ||
	    (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX))
		val = 1;
	REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, val);
	REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x0);
	REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x0);
	REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, 0x0);
	REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x1);
	REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x1);

	vars->mac_type = MAC_TYPE_BMAC;
	return rc;
}


static void bnx2x_update_mng(struct link_params *params, u32 link_status)
{
	struct bnx2x *bp = params->bp;

	REG_WR(bp, params->shmem_base +
	       offsetof(struct shmem_region,
			port_mb[params->port].link_status), link_status);
}

static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port)
{
	u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
			NIG_REG_INGRESS_BMAC0_MEM;
	u32 wb_data[2];
	u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4);

	/* Only if the bmac is out of reset */
	if (REG_RD(bp, MISC_REG_RESET_REG_2) &
			(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port) &&
	    nig_bmac_enable) {

		if (CHIP_IS_E2(bp)) {
			/* Clear Rx Enable bit in BMAC_CONTROL register */
			REG_RD_DMAE(bp, bmac_addr +
				    BIGMAC2_REGISTER_BMAC_CONTROL,
				    wb_data, 2);
			wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
			REG_WR_DMAE(bp, bmac_addr +
				    BIGMAC2_REGISTER_BMAC_CONTROL,
				    wb_data, 2);
		} else {
			/* Clear Rx Enable bit in BMAC_CONTROL register */
			REG_RD_DMAE(bp, bmac_addr +
					BIGMAC_REGISTER_BMAC_CONTROL,
					wb_data, 2);
			wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
			REG_WR_DMAE(bp, bmac_addr +
					BIGMAC_REGISTER_BMAC_CONTROL,
					wb_data, 2);
		}
		msleep(1);
	}
}

static int bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl,
			    u32 line_speed)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;
	u32 init_crd, crd;
	u32 count = 1000;

	/* disable port */
	REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1);

	/* wait for init credit */
	init_crd = REG_RD(bp, PBF_REG_P0_INIT_CRD + port*4);
	crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
	DP(NETIF_MSG_LINK, "init_crd 0x%x  crd 0x%x\n", init_crd, crd);

	while ((init_crd != crd) && count) {
		msleep(5);

		crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
		count--;
	}
	crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8);
	if (init_crd != crd) {
		DP(NETIF_MSG_LINK, "BUG! init_crd 0x%x != crd 0x%x\n",
			  init_crd, crd);
		return -EINVAL;
	}

	if (flow_ctrl & BNX2X_FLOW_CTRL_RX ||
	    line_speed == SPEED_10 ||
	    line_speed == SPEED_100 ||
	    line_speed == SPEED_1000 ||
	    line_speed == SPEED_2500) {
		REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1);
		/* update threshold */
		REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0);
		/* update init credit */
		init_crd = 778;		/* (800-18-4) */

	} else {
		u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE +
			      ETH_OVREHEAD)/16;
		REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0);
		/* update threshold */
		REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh);
		/* update init credit */
		switch (line_speed) {
		case SPEED_10000:
			init_crd = thresh + 553 - 22;
			break;

		case SPEED_12000:
			init_crd = thresh + 664 - 22;
			break;

		case SPEED_13000:
			init_crd = thresh + 742 - 22;
			break;

		case SPEED_16000:
			init_crd = thresh + 778 - 22;
			break;
		default:
			DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
				  line_speed);
			return -EINVAL;
		}
	}
	REG_WR(bp, PBF_REG_P0_INIT_CRD + port*4, init_crd);
	DP(NETIF_MSG_LINK, "PBF updated to speed %d credit %d\n",
		 line_speed, init_crd);

	/* probe the credit changes */
	REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x1);
	msleep(5);
	REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x0);

	/* enable port */
	REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x0);
	return 0;
}

/**
 * bnx2x_get_emac_base - retrive emac base address
 *
 * @bp:			driver handle
 * @mdc_mdio_access:	access type
 * @port:		port id
 *
 * This function selects the MDC/MDIO access (through emac0 or
 * emac1) depend on the mdc_mdio_access, port, port swapped. Each
 * phy has a default access mode, which could also be overridden
 * by nvram configuration. This parameter, whether this is the
 * default phy configuration, or the nvram overrun
 * configuration, is passed here as mdc_mdio_access and selects
 * the emac_base for the CL45 read/writes operations
 */
static u32 bnx2x_get_emac_base(struct bnx2x *bp,
			       u32 mdc_mdio_access, u8 port)
{
	u32 emac_base = 0;
	switch (mdc_mdio_access) {
	case SHARED_HW_CFG_MDC_MDIO_ACCESS1_PHY_TYPE:
		break;
	case SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC0:
		if (REG_RD(bp, NIG_REG_PORT_SWAP))
			emac_base = GRCBASE_EMAC1;
		else
			emac_base = GRCBASE_EMAC0;
		break;
	case SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1:
		if (REG_RD(bp, NIG_REG_PORT_SWAP))
			emac_base = GRCBASE_EMAC0;
		else
			emac_base = GRCBASE_EMAC1;
		break;
	case SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH:
		emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
		break;
	case SHARED_HW_CFG_MDC_MDIO_ACCESS1_SWAPPED:
		emac_base = (port) ? GRCBASE_EMAC0 : GRCBASE_EMAC1;
		break;
	default:
		break;
	}
	return emac_base;

}

/******************************************************************/
/*			CL45 access functions			  */
/******************************************************************/
static int bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy,
			    u8 devad, u16 reg, u16 val)
{
	u32 tmp, saved_mode;
	u8 i;
	int rc = 0;
	/*
	 * Set clause 45 mode, slow down the MDIO clock to 2.5MHz
	 * (a value of 49==0x31) and make sure that the AUTO poll is off
	 */

	saved_mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
	tmp = saved_mode & ~(EMAC_MDIO_MODE_AUTO_POLL |
			     EMAC_MDIO_MODE_CLOCK_CNT);
	tmp |= (EMAC_MDIO_MODE_CLAUSE_45 |
		(49 << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT));
	REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, tmp);
	REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
	udelay(40);

	/* address */

	tmp = ((phy->addr << 21) | (devad << 16) | reg |
	       EMAC_MDIO_COMM_COMMAND_ADDRESS |
	       EMAC_MDIO_COMM_START_BUSY);
	REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);

	for (i = 0; i < 50; i++) {
		udelay(10);

		tmp = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
		if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
			udelay(5);
			break;
		}
	}
	if (tmp & EMAC_MDIO_COMM_START_BUSY) {
		DP(NETIF_MSG_LINK, "write phy register failed\n");
		netdev_err(bp->dev,  "MDC/MDIO access timeout\n");
		rc = -EFAULT;
	} else {
		/* data */
		tmp = ((phy->addr << 21) | (devad << 16) | val |
		       EMAC_MDIO_COMM_COMMAND_WRITE_45 |
		       EMAC_MDIO_COMM_START_BUSY);
		REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp);

		for (i = 0; i < 50; i++) {
			udelay(10);

			tmp = REG_RD(bp, phy->mdio_ctrl +
				     EMAC_REG_EMAC_MDIO_COMM);
			if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) {
				udelay(5);
				break;
			}
		}
		if (tmp & EMAC_MDIO_COMM_START_BUSY) {
			DP(NETIF_MSG_LINK, "write phy register failed\n");
			netdev_err(bp->dev,  "MDC/MDIO access timeout\n");
			rc = -EFAULT;
		}
	}

	/* Restore the saved mode */
	REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, saved_mode);

	return rc;
}

static int bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy,
			   u8 devad, u16 reg, u16 *ret_val)
{
	u32 val, saved_mode;
	u16 i;
	int rc = 0;
	/*
	 * Set clause 45 mode, slow down the MDIO clock to 2.5MHz
	 * (a value of 49==0x31) and make sure that the AUTO poll is off
	 */

	saved_mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
	val = saved_mode & ~((EMAC_MDIO_MODE_AUTO_POLL |
			      EMAC_MDIO_MODE_CLOCK_CNT));
	val |= (EMAC_MDIO_MODE_CLAUSE_45 |
		(49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT));
	REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, val);
	REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE);
	udelay(40);

	/* address */
	val = ((phy->addr << 21) | (devad << 16) | reg |
	       EMAC_MDIO_COMM_COMMAND_ADDRESS |
	       EMAC_MDIO_COMM_START_BUSY);
	REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);

	for (i = 0; i < 50; i++) {
		udelay(10);

		val = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM);
		if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
			udelay(5);
			break;
		}
	}
	if (val & EMAC_MDIO_COMM_START_BUSY) {
		DP(NETIF_MSG_LINK, "read phy register failed\n");
		netdev_err(bp->dev,  "MDC/MDIO access timeout\n");
		*ret_val = 0;
		rc = -EFAULT;

	} else {
		/* data */
		val = ((phy->addr << 21) | (devad << 16) |
		       EMAC_MDIO_COMM_COMMAND_READ_45 |
		       EMAC_MDIO_COMM_START_BUSY);
		REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val);

		for (i = 0; i < 50; i++) {
			udelay(10);

			val = REG_RD(bp, phy->mdio_ctrl +
				     EMAC_REG_EMAC_MDIO_COMM);
			if (!(val & EMAC_MDIO_COMM_START_BUSY)) {
				*ret_val = (u16)(val & EMAC_MDIO_COMM_DATA);
				break;
			}
		}
		if (val & EMAC_MDIO_COMM_START_BUSY) {
			DP(NETIF_MSG_LINK, "read phy register failed\n");
			netdev_err(bp->dev,  "MDC/MDIO access timeout\n");
			*ret_val = 0;
			rc = -EFAULT;
		}
	}

	/* Restore the saved mode */
	REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, saved_mode);

	return rc;
}

int bnx2x_phy_read(struct link_params *params, u8 phy_addr,
		   u8 devad, u16 reg, u16 *ret_val)
{
	u8 phy_index;
	/*
	 * Probe for the phy according to the given phy_addr, and execute
	 * the read request on it
	 */
	for (phy_index = 0; phy_index < params->num_phys; phy_index++) {
		if (params->phy[phy_index].addr == phy_addr) {
			return bnx2x_cl45_read(params->bp,
					       &params->phy[phy_index], devad,
					       reg, ret_val);
		}
	}
	return -EINVAL;
}

int bnx2x_phy_write(struct link_params *params, u8 phy_addr,
		    u8 devad, u16 reg, u16 val)
{
	u8 phy_index;
	/*
	 * Probe for the phy according to the given phy_addr, and execute
	 * the write request on it
	 */
	for (phy_index = 0; phy_index < params->num_phys; phy_index++) {
		if (params->phy[phy_index].addr == phy_addr) {
			return bnx2x_cl45_write(params->bp,
						&params->phy[phy_index], devad,
						reg, val);
		}
	}
	return -EINVAL;
}

static void bnx2x_set_aer_mmd_xgxs(struct link_params *params,
				   struct bnx2x_phy *phy)
{
	u32 ser_lane;
	u16 offset, aer_val;
	struct bnx2x *bp = params->bp;
	ser_lane = ((params->lane_config &
		     PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
		     PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);

	offset = phy->addr + ser_lane;
	if (CHIP_IS_E2(bp))
		aer_val = 0x3800 + offset - 1;
	else
		aer_val = 0x3800 + offset;
	CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK,
			  MDIO_AER_BLOCK_AER_REG, aer_val);
}
static void bnx2x_set_aer_mmd_serdes(struct bnx2x *bp,
				     struct bnx2x_phy *phy)
{
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_AER_BLOCK,
			  MDIO_AER_BLOCK_AER_REG, 0x3800);
}

/******************************************************************/
/*			Internal phy section			  */
/******************************************************************/

static void bnx2x_set_serdes_access(struct bnx2x *bp, u8 port)
{
	u32 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;

	/* Set Clause 22 */
	REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + port*0x10, 1);
	REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245f8000);
	udelay(500);
	REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245d000f);
	udelay(500);
	 /* Set Clause 45 */
	REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + port*0x10, 0);
}

static void bnx2x_serdes_deassert(struct bnx2x *bp, u8 port)
{
	u32 val;

	DP(NETIF_MSG_LINK, "bnx2x_serdes_deassert\n");

	val = SERDES_RESET_BITS << (port*16);

	/* reset and unreset the SerDes/XGXS */
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val);
	udelay(500);
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);

	bnx2x_set_serdes_access(bp, port);

	REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD + port*0x10,
	       DEFAULT_PHY_DEV_ADDR);
}

static void bnx2x_xgxs_deassert(struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u8 port;
	u32 val;
	DP(NETIF_MSG_LINK, "bnx2x_xgxs_deassert\n");
	port = params->port;

	val = XGXS_RESET_BITS << (port*16);

	/* reset and unreset the SerDes/XGXS */
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val);
	udelay(500);
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val);

	REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST + port*0x18, 0);
	REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
	       params->phy[INT_PHY].def_md_devad);
}


void bnx2x_link_status_update(struct link_params *params,
			      struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u8 link_10g;
	u8 port = params->port;
	u32 sync_offset, media_types;
	vars->link_status = REG_RD(bp, params->shmem_base +
				   offsetof(struct shmem_region,
					    port_mb[port].link_status));

	vars->link_up = (vars->link_status & LINK_STATUS_LINK_UP);

	if (vars->link_up) {
		DP(NETIF_MSG_LINK, "phy link up\n");

		vars->phy_link_up = 1;
		vars->duplex = DUPLEX_FULL;
		switch (vars->link_status &
			LINK_STATUS_SPEED_AND_DUPLEX_MASK) {
			case LINK_10THD:
				vars->duplex = DUPLEX_HALF;
				/* fall thru */
			case LINK_10TFD:
				vars->line_speed = SPEED_10;
				break;

			case LINK_100TXHD:
				vars->duplex = DUPLEX_HALF;
				/* fall thru */
			case LINK_100T4:
			case LINK_100TXFD:
				vars->line_speed = SPEED_100;
				break;

			case LINK_1000THD:
				vars->duplex = DUPLEX_HALF;
				/* fall thru */
			case LINK_1000TFD:
				vars->line_speed = SPEED_1000;
				break;

			case LINK_2500THD:
				vars->duplex = DUPLEX_HALF;
				/* fall thru */
			case LINK_2500TFD:
				vars->line_speed = SPEED_2500;
				break;

			case LINK_10GTFD:
				vars->line_speed = SPEED_10000;
				break;

			case LINK_12GTFD:
				vars->line_speed = SPEED_12000;
				break;

			case LINK_12_5GTFD:
				vars->line_speed = SPEED_12500;
				break;

			case LINK_13GTFD:
				vars->line_speed = SPEED_13000;
				break;

			case LINK_15GTFD:
				vars->line_speed = SPEED_15000;
				break;

			case LINK_16GTFD:
				vars->line_speed = SPEED_16000;
				break;

			default:
				break;
		}
		vars->flow_ctrl = 0;
		if (vars->link_status & LINK_STATUS_TX_FLOW_CONTROL_ENABLED)
			vars->flow_ctrl |= BNX2X_FLOW_CTRL_TX;

		if (vars->link_status & LINK_STATUS_RX_FLOW_CONTROL_ENABLED)
			vars->flow_ctrl |= BNX2X_FLOW_CTRL_RX;

		if (!vars->flow_ctrl)
			vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;

		if (vars->line_speed &&
		    ((vars->line_speed == SPEED_10) ||
		     (vars->line_speed == SPEED_100))) {
			vars->phy_flags |= PHY_SGMII_FLAG;
		} else {
			vars->phy_flags &= ~PHY_SGMII_FLAG;
		}

		/* anything 10 and over uses the bmac */
		link_10g = ((vars->line_speed == SPEED_10000) ||
			    (vars->line_speed == SPEED_12000) ||
			    (vars->line_speed == SPEED_12500) ||
			    (vars->line_speed == SPEED_13000) ||
			    (vars->line_speed == SPEED_15000) ||
			    (vars->line_speed == SPEED_16000));
		if (link_10g)
			vars->mac_type = MAC_TYPE_BMAC;
		else
			vars->mac_type = MAC_TYPE_EMAC;

	} else { /* link down */
		DP(NETIF_MSG_LINK, "phy link down\n");

		vars->phy_link_up = 0;

		vars->line_speed = 0;
		vars->duplex = DUPLEX_FULL;
		vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;

		/* indicate no mac active */
		vars->mac_type = MAC_TYPE_NONE;
	}

	/* Sync media type */
	sync_offset = params->shmem_base +
			offsetof(struct shmem_region,
				 dev_info.port_hw_config[port].media_type);
	media_types = REG_RD(bp, sync_offset);

	params->phy[INT_PHY].media_type =
		(media_types & PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) >>
		PORT_HW_CFG_MEDIA_TYPE_PHY0_SHIFT;
	params->phy[EXT_PHY1].media_type =
		(media_types & PORT_HW_CFG_MEDIA_TYPE_PHY1_MASK) >>
		PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT;
	params->phy[EXT_PHY2].media_type =
		(media_types & PORT_HW_CFG_MEDIA_TYPE_PHY2_MASK) >>
		PORT_HW_CFG_MEDIA_TYPE_PHY2_SHIFT;
	DP(NETIF_MSG_LINK, "media_types = 0x%x\n", media_types);

	DP(NETIF_MSG_LINK, "link_status 0x%x  phy_link_up %x\n",
		 vars->link_status, vars->phy_link_up);
	DP(NETIF_MSG_LINK, "line_speed %x  duplex %x  flow_ctrl 0x%x\n",
		 vars->line_speed, vars->duplex, vars->flow_ctrl);
}


static void bnx2x_set_master_ln(struct link_params *params,
				struct bnx2x_phy *phy)
{
	struct bnx2x *bp = params->bp;
	u16 new_master_ln, ser_lane;
	ser_lane = ((params->lane_config &
		     PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
		    PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);

	/* set the master_ln for AN */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_XGXS_BLOCK2,
			  MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
			  &new_master_ln);

	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_XGXS_BLOCK2 ,
			  MDIO_XGXS_BLOCK2_TEST_MODE_LANE,
			  (new_master_ln | ser_lane));
}

static int bnx2x_reset_unicore(struct link_params *params,
			       struct bnx2x_phy *phy,
			       u8 set_serdes)
{
	struct bnx2x *bp = params->bp;
	u16 mii_control;
	u16 i;
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_COMBO_IEEE0,
			  MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control);

	/* reset the unicore */
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_COMBO_IEEE0,
			  MDIO_COMBO_IEEE0_MII_CONTROL,
			  (mii_control |
			   MDIO_COMBO_IEEO_MII_CONTROL_RESET));
	if (set_serdes)
		bnx2x_set_serdes_access(bp, params->port);

	/* wait for the reset to self clear */
	for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) {
		udelay(5);

		/* the reset erased the previous bank value */
		CL22_RD_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_COMBO_IEEE0,
				  MDIO_COMBO_IEEE0_MII_CONTROL,
				  &mii_control);

		if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) {
			udelay(5);
			return 0;
		}
	}

	netdev_err(bp->dev,  "Warning: PHY was not initialized,"
			      " Port %d\n",
			 params->port);
	DP(NETIF_MSG_LINK, "BUG! XGXS is still in reset!\n");
	return -EINVAL;

}

static void bnx2x_set_swap_lanes(struct link_params *params,
				 struct bnx2x_phy *phy)
{
	struct bnx2x *bp = params->bp;
	/*
	 *  Each two bits represents a lane number:
	 *  No swap is 0123 => 0x1b no need to enable the swap
	 */
	u16 ser_lane, rx_lane_swap, tx_lane_swap;

	ser_lane = ((params->lane_config &
		     PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
		    PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
	rx_lane_swap = ((params->lane_config &
			 PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >>
			PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT);
	tx_lane_swap = ((params->lane_config &
			 PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >>
			PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT);

	if (rx_lane_swap != 0x1b) {
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_XGXS_BLOCK2,
				  MDIO_XGXS_BLOCK2_RX_LN_SWAP,
				  (rx_lane_swap |
				   MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE |
				   MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE));
	} else {
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_XGXS_BLOCK2,
				  MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0);
	}

	if (tx_lane_swap != 0x1b) {
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_XGXS_BLOCK2,
				  MDIO_XGXS_BLOCK2_TX_LN_SWAP,
				  (tx_lane_swap |
				   MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE));
	} else {
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_XGXS_BLOCK2,
				  MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0);
	}
}

static void bnx2x_set_parallel_detection(struct bnx2x_phy *phy,
					 struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u16 control2;
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
			  &control2);
	if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
		control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
	else
		control2 &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN;
	DP(NETIF_MSG_LINK, "phy->speed_cap_mask = 0x%x, control2 = 0x%x\n",
		phy->speed_cap_mask, control2);
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_CONTROL2,
			  control2);

	if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
	     (phy->speed_cap_mask &
		    PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
		DP(NETIF_MSG_LINK, "XGXS\n");

		CL22_WR_OVER_CL45(bp, phy,
				 MDIO_REG_BANK_10G_PARALLEL_DETECT,
				 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK,
				 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT);

		CL22_RD_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_10G_PARALLEL_DETECT,
				  MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
				  &control2);


		control2 |=
		    MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN;

		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_10G_PARALLEL_DETECT,
				  MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL,
				  control2);

		/* Disable parallel detection of HiG */
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_XGXS_BLOCK2,
				  MDIO_XGXS_BLOCK2_UNICORE_MODE_10G,
				  MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS |
				  MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS);
	}
}

static void bnx2x_set_autoneg(struct bnx2x_phy *phy,
			      struct link_params *params,
			      struct link_vars *vars,
			      u8 enable_cl73)
{
	struct bnx2x *bp = params->bp;
	u16 reg_val;

	/* CL37 Autoneg */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_COMBO_IEEE0,
			  MDIO_COMBO_IEEE0_MII_CONTROL, &reg_val);

	/* CL37 Autoneg Enabled */
	if (vars->line_speed == SPEED_AUTO_NEG)
		reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN;
	else /* CL37 Autoneg Disabled */
		reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
			     MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN);

	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_COMBO_IEEE0,
			  MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);

	/* Enable/Disable Autodetection */

	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, &reg_val);
	reg_val &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN |
		    MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT);
	reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE;
	if (vars->line_speed == SPEED_AUTO_NEG)
		reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;
	else
		reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET;

	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val);

	/* Enable TetonII and BAM autoneg */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_BAM_NEXT_PAGE,
			  MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
			  &reg_val);
	if (vars->line_speed == SPEED_AUTO_NEG) {
		/* Enable BAM aneg Mode and TetonII aneg Mode */
		reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
			    MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
	} else {
		/* TetonII and BAM Autoneg Disabled */
		reg_val &= ~(MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE |
			     MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN);
	}
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_BAM_NEXT_PAGE,
			  MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
			  reg_val);

	if (enable_cl73) {
		/* Enable Cl73 FSM status bits */
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_CL73_USERB0,
				  MDIO_CL73_USERB0_CL73_UCTRL,
				  0xe);

		/* Enable BAM Station Manager*/
		CL22_WR_OVER_CL45(bp, phy,
			MDIO_REG_BANK_CL73_USERB0,
			MDIO_CL73_USERB0_CL73_BAM_CTRL1,
			MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN |
			MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN |
			MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN);

		/* Advertise CL73 link speeds */
		CL22_RD_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_CL73_IEEEB1,
				  MDIO_CL73_IEEEB1_AN_ADV2,
				  &reg_val);
		if (phy->speed_cap_mask &
		    PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
			reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4;
		if (phy->speed_cap_mask &
		    PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
			reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX;

		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_CL73_IEEEB1,
				  MDIO_CL73_IEEEB1_AN_ADV2,
				  reg_val);

		/* CL73 Autoneg Enabled */
		reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN;

	} else /* CL73 Autoneg Disabled */
		reg_val = 0;

	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_CL73_IEEEB0,
			  MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val);
}

/* program SerDes, forced speed */
static void bnx2x_program_serdes(struct bnx2x_phy *phy,
				 struct link_params *params,
				 struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 reg_val;

	/* program duplex, disable autoneg and sgmii*/
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_COMBO_IEEE0,
			  MDIO_COMBO_IEEE0_MII_CONTROL, &reg_val);
	reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX |
		     MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
		     MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK);
	if (phy->req_duplex == DUPLEX_FULL)
		reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_COMBO_IEEE0,
			  MDIO_COMBO_IEEE0_MII_CONTROL, reg_val);

	/*
	 * program speed
	 *  - needed only if the speed is greater than 1G (2.5G or 10G)
	 */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_MISC1, &reg_val);
	/* clearing the speed value before setting the right speed */
	DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val);

	reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK |
		     MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);

	if (!((vars->line_speed == SPEED_1000) ||
	      (vars->line_speed == SPEED_100) ||
	      (vars->line_speed == SPEED_10))) {

		reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M |
			    MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL);
		if (vars->line_speed == SPEED_10000)
			reg_val |=
				MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4;
		if (vars->line_speed == SPEED_13000)
			reg_val |=
				MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G;
	}

	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_MISC1, reg_val);

}

static void bnx2x_set_brcm_cl37_advertisment(struct bnx2x_phy *phy,
					     struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u16 val = 0;

	/* configure the 48 bits for BAM AN */

	/* set extended capabilities */
	if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)
		val |= MDIO_OVER_1G_UP1_2_5G;
	if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
		val |= MDIO_OVER_1G_UP1_10G;
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_OVER_1G,
			  MDIO_OVER_1G_UP1, val);

	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_OVER_1G,
			  MDIO_OVER_1G_UP3, 0x400);
}

static void bnx2x_calc_ieee_aneg_adv(struct bnx2x_phy *phy,
				     struct link_params *params, u16 *ieee_fc)
{
	struct bnx2x *bp = params->bp;
	*ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX;
	/*
	 * Resolve pause mode and advertisement.
	 * Please refer to Table 28B-3 of the 802.3ab-1999 spec
	 */

	switch (phy->req_flow_ctrl) {
	case BNX2X_FLOW_CTRL_AUTO:
		if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH)
			*ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
		else
			*ieee_fc |=
			MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
		break;
	case BNX2X_FLOW_CTRL_TX:
		*ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
		break;

	case BNX2X_FLOW_CTRL_RX:
	case BNX2X_FLOW_CTRL_BOTH:
		*ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
		break;

	case BNX2X_FLOW_CTRL_NONE:
	default:
		*ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE;
		break;
	}
	DP(NETIF_MSG_LINK, "ieee_fc = 0x%x\n", *ieee_fc);
}

static void bnx2x_set_ieee_aneg_advertisment(struct bnx2x_phy *phy,
					     struct link_params *params,
					     u16 ieee_fc)
{
	struct bnx2x *bp = params->bp;
	u16 val;
	/* for AN, we are always publishing full duplex */

	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_COMBO_IEEE0,
			  MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc);
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_CL73_IEEEB1,
			  MDIO_CL73_IEEEB1_AN_ADV1, &val);
	val &= ~MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH;
	val |= ((ieee_fc<<3) & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK);
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_CL73_IEEEB1,
			  MDIO_CL73_IEEEB1_AN_ADV1, val);
}

static void bnx2x_restart_autoneg(struct bnx2x_phy *phy,
				  struct link_params *params,
				  u8 enable_cl73)
{
	struct bnx2x *bp = params->bp;
	u16 mii_control;

	DP(NETIF_MSG_LINK, "bnx2x_restart_autoneg\n");
	/* Enable and restart BAM/CL37 aneg */

	if (enable_cl73) {
		CL22_RD_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_CL73_IEEEB0,
				  MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
				  &mii_control);

		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_CL73_IEEEB0,
				  MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
				  (mii_control |
				  MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN |
				  MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN));
	} else {

		CL22_RD_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_COMBO_IEEE0,
				  MDIO_COMBO_IEEE0_MII_CONTROL,
				  &mii_control);
		DP(NETIF_MSG_LINK,
			 "bnx2x_restart_autoneg mii_control before = 0x%x\n",
			 mii_control);
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_COMBO_IEEE0,
				  MDIO_COMBO_IEEE0_MII_CONTROL,
				  (mii_control |
				   MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
				   MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
	}
}

static void bnx2x_initialize_sgmii_process(struct bnx2x_phy *phy,
					   struct link_params *params,
					   struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 control1;

	/* in SGMII mode, the unicore is always slave */

	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
			  &control1);
	control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT;
	/* set sgmii mode (and not fiber) */
	control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE |
		      MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET |
		      MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE);
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_CONTROL1,
			  control1);

	/* if forced speed */
	if (!(vars->line_speed == SPEED_AUTO_NEG)) {
		/* set speed, disable autoneg */
		u16 mii_control;

		CL22_RD_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_COMBO_IEEE0,
				  MDIO_COMBO_IEEE0_MII_CONTROL,
				  &mii_control);
		mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
				 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK|
				 MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX);

		switch (vars->line_speed) {
		case SPEED_100:
			mii_control |=
				MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100;
			break;
		case SPEED_1000:
			mii_control |=
				MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000;
			break;
		case SPEED_10:
			/* there is nothing to set for 10M */
			break;
		default:
			/* invalid speed for SGMII */
			DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
				  vars->line_speed);
			break;
		}

		/* setting the full duplex */
		if (phy->req_duplex == DUPLEX_FULL)
			mii_control |=
				MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX;
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_COMBO_IEEE0,
				  MDIO_COMBO_IEEE0_MII_CONTROL,
				  mii_control);

	} else { /* AN mode */
		/* enable and restart AN */
		bnx2x_restart_autoneg(phy, params, 0);
	}
}


/*
 * link management
 */

static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result)
{						/*  LD	    LP	 */
	switch (pause_result) {			/* ASYM P ASYM P */
	case 0xb:				/*   1  0   1  1 */
		vars->flow_ctrl = BNX2X_FLOW_CTRL_TX;
		break;

	case 0xe:				/*   1  1   1  0 */
		vars->flow_ctrl = BNX2X_FLOW_CTRL_RX;
		break;

	case 0x5:				/*   0  1   0  1 */
	case 0x7:				/*   0  1   1  1 */
	case 0xd:				/*   1  1   0  1 */
	case 0xf:				/*   1  1   1  1 */
		vars->flow_ctrl = BNX2X_FLOW_CTRL_BOTH;
		break;

	default:
		break;
	}
	if (pause_result & (1<<0))
		vars->link_status |= LINK_STATUS_LINK_PARTNER_SYMMETRIC_PAUSE;
	if (pause_result & (1<<1))
		vars->link_status |= LINK_STATUS_LINK_PARTNER_ASYMMETRIC_PAUSE;
}

static int bnx2x_direct_parallel_detect_used(struct bnx2x_phy *phy,
					     struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u16 pd_10g, status2_1000x;
	if (phy->req_line_speed != SPEED_AUTO_NEG)
		return 0;
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
			  &status2_1000x);
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_SERDES_DIGITAL,
			  MDIO_SERDES_DIGITAL_A_1000X_STATUS2,
			  &status2_1000x);
	if (status2_1000x & MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED) {
		DP(NETIF_MSG_LINK, "1G parallel detect link on port %d\n",
			 params->port);
		return 1;
	}

	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_10G_PARALLEL_DETECT,
			  MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS,
			  &pd_10g);

	if (pd_10g & MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK) {
		DP(NETIF_MSG_LINK, "10G parallel detect link on port %d\n",
			 params->port);
		return 1;
	}
	return 0;
}

static void bnx2x_flow_ctrl_resolve(struct bnx2x_phy *phy,
				    struct link_params *params,
				    struct link_vars *vars,
				    u32 gp_status)
{
	struct bnx2x *bp = params->bp;
	u16 ld_pause;   /* local driver */
	u16 lp_pause;   /* link partner */
	u16 pause_result;

	vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;

	/* resolve from gp_status in case of AN complete and not sgmii */
	if (phy->req_flow_ctrl != BNX2X_FLOW_CTRL_AUTO)
		vars->flow_ctrl = phy->req_flow_ctrl;
	else if (phy->req_line_speed != SPEED_AUTO_NEG)
		vars->flow_ctrl = params->req_fc_auto_adv;
	else if ((gp_status & MDIO_AN_CL73_OR_37_COMPLETE) &&
		 (!(vars->phy_flags & PHY_SGMII_FLAG))) {
		if (bnx2x_direct_parallel_detect_used(phy, params)) {
			vars->flow_ctrl = params->req_fc_auto_adv;
			return;
		}
		if ((gp_status &
		    (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE |
		     MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) ==
		    (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE |
		     MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) {

			CL22_RD_OVER_CL45(bp, phy,
					  MDIO_REG_BANK_CL73_IEEEB1,
					  MDIO_CL73_IEEEB1_AN_ADV1,
					  &ld_pause);
			CL22_RD_OVER_CL45(bp, phy,
					  MDIO_REG_BANK_CL73_IEEEB1,
					  MDIO_CL73_IEEEB1_AN_LP_ADV1,
					  &lp_pause);
			pause_result = (ld_pause &
					MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK)
					>> 8;
			pause_result |= (lp_pause &
					MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK)
					>> 10;
			DP(NETIF_MSG_LINK, "pause_result CL73 0x%x\n",
				 pause_result);
		} else {
			CL22_RD_OVER_CL45(bp, phy,
					  MDIO_REG_BANK_COMBO_IEEE0,
					  MDIO_COMBO_IEEE0_AUTO_NEG_ADV,
					  &ld_pause);
			CL22_RD_OVER_CL45(bp, phy,
				MDIO_REG_BANK_COMBO_IEEE0,
				MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1,
				&lp_pause);
			pause_result = (ld_pause &
				MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5;
			pause_result |= (lp_pause &
				MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7;
			DP(NETIF_MSG_LINK, "pause_result CL37 0x%x\n",
				 pause_result);
		}
		bnx2x_pause_resolve(vars, pause_result);
	}
	DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl);
}

static void bnx2x_check_fallback_to_cl37(struct bnx2x_phy *phy,
					 struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u16 rx_status, ustat_val, cl37_fsm_recieved;
	DP(NETIF_MSG_LINK, "bnx2x_check_fallback_to_cl37\n");
	/* Step 1: Make sure signal is detected */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_RX0,
			  MDIO_RX0_RX_STATUS,
			  &rx_status);
	if ((rx_status & MDIO_RX0_RX_STATUS_SIGDET) !=
	    (MDIO_RX0_RX_STATUS_SIGDET)) {
		DP(NETIF_MSG_LINK, "Signal is not detected. Restoring CL73."
			     "rx_status(0x80b0) = 0x%x\n", rx_status);
		CL22_WR_OVER_CL45(bp, phy,
				  MDIO_REG_BANK_CL73_IEEEB0,
				  MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
				  MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN);
		return;
	}
	/* Step 2: Check CL73 state machine */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_CL73_USERB0,
			  MDIO_CL73_USERB0_CL73_USTAT1,
			  &ustat_val);
	if ((ustat_val &
	     (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK |
	      MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) !=
	    (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK |
	      MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) {
		DP(NETIF_MSG_LINK, "CL73 state-machine is not stable. "
			     "ustat_val(0x8371) = 0x%x\n", ustat_val);
		return;
	}
	/*
	 * Step 3: Check CL37 Message Pages received to indicate LP
	 * supports only CL37
	 */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_REMOTE_PHY,
			  MDIO_REMOTE_PHY_MISC_RX_STATUS,
			  &cl37_fsm_recieved);
	if ((cl37_fsm_recieved &
	     (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG |
	     MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) !=
	    (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG |
	      MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) {
		DP(NETIF_MSG_LINK, "No CL37 FSM were received. "
			     "misc_rx_status(0x8330) = 0x%x\n",
			 cl37_fsm_recieved);
		return;
	}
	/*
	 * The combined cl37/cl73 fsm state information indicating that
	 * we are connected to a device which does not support cl73, but
	 * does support cl37 BAM. In this case we disable cl73 and
	 * restart cl37 auto-neg
	 */

	/* Disable CL73 */
	CL22_WR_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_CL73_IEEEB0,
			  MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
			  0);
	/* Restart CL37 autoneg */
	bnx2x_restart_autoneg(phy, params, 0);
	DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n");
}

static void bnx2x_xgxs_an_resolve(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars,
				  u32 gp_status)
{
	if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE)
		vars->link_status |=
			LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;

	if (bnx2x_direct_parallel_detect_used(phy, params))
		vars->link_status |=
			LINK_STATUS_PARALLEL_DETECTION_USED;
}

static int bnx2x_link_settings_status(struct bnx2x_phy *phy,
				      struct link_params *params,
				      struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 new_line_speed, gp_status;
	int rc = 0;

	/* Read gp_status */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_GP_STATUS,
			  MDIO_GP_STATUS_TOP_AN_STATUS1,
			  &gp_status);

	if (phy->req_line_speed == SPEED_AUTO_NEG)
		vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED;
	if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) {
		DP(NETIF_MSG_LINK, "phy link up gp_status=0x%x\n",
			 gp_status);

		vars->phy_link_up = 1;
		vars->link_status |= LINK_STATUS_LINK_UP;

		if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS)
			vars->duplex = DUPLEX_FULL;
		else
			vars->duplex = DUPLEX_HALF;

		if (SINGLE_MEDIA_DIRECT(params)) {
			bnx2x_flow_ctrl_resolve(phy, params, vars, gp_status);
			if (phy->req_line_speed == SPEED_AUTO_NEG)
				bnx2x_xgxs_an_resolve(phy, params, vars,
						      gp_status);
		}

		switch (gp_status & GP_STATUS_SPEED_MASK) {
		case GP_STATUS_10M:
			new_line_speed = SPEED_10;
			if (vars->duplex == DUPLEX_FULL)
				vars->link_status |= LINK_10TFD;
			else
				vars->link_status |= LINK_10THD;
			break;

		case GP_STATUS_100M:
			new_line_speed = SPEED_100;
			if (vars->duplex == DUPLEX_FULL)
				vars->link_status |= LINK_100TXFD;
			else
				vars->link_status |= LINK_100TXHD;
			break;

		case GP_STATUS_1G:
		case GP_STATUS_1G_KX:
			new_line_speed = SPEED_1000;
			if (vars->duplex == DUPLEX_FULL)
				vars->link_status |= LINK_1000TFD;
			else
				vars->link_status |= LINK_1000THD;
			break;

		case GP_STATUS_2_5G:
			new_line_speed = SPEED_2500;
			if (vars->duplex == DUPLEX_FULL)
				vars->link_status |= LINK_2500TFD;
			else
				vars->link_status |= LINK_2500THD;
			break;

		case GP_STATUS_5G:
		case GP_STATUS_6G:
			DP(NETIF_MSG_LINK,
				 "link speed unsupported  gp_status 0x%x\n",
				  gp_status);
			return -EINVAL;

		case GP_STATUS_10G_KX4:
		case GP_STATUS_10G_HIG:
		case GP_STATUS_10G_CX4:
			new_line_speed = SPEED_10000;
			vars->link_status |= LINK_10GTFD;
			break;

		case GP_STATUS_12G_HIG:
			new_line_speed = SPEED_12000;
			vars->link_status |= LINK_12GTFD;
			break;

		case GP_STATUS_12_5G:
			new_line_speed = SPEED_12500;
			vars->link_status |= LINK_12_5GTFD;
			break;

		case GP_STATUS_13G:
			new_line_speed = SPEED_13000;
			vars->link_status |= LINK_13GTFD;
			break;

		case GP_STATUS_15G:
			new_line_speed = SPEED_15000;
			vars->link_status |= LINK_15GTFD;
			break;

		case GP_STATUS_16G:
			new_line_speed = SPEED_16000;
			vars->link_status |= LINK_16GTFD;
			break;

		default:
			DP(NETIF_MSG_LINK,
				  "link speed unsupported gp_status 0x%x\n",
				  gp_status);
			return -EINVAL;
		}

		vars->line_speed = new_line_speed;

	} else { /* link_down */
		DP(NETIF_MSG_LINK, "phy link down\n");

		vars->phy_link_up = 0;

		vars->duplex = DUPLEX_FULL;
		vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
		vars->mac_type = MAC_TYPE_NONE;

		if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
		    SINGLE_MEDIA_DIRECT(params)) {
			/* Check signal is detected */
			bnx2x_check_fallback_to_cl37(phy, params);
		}
	}

	DP(NETIF_MSG_LINK, "gp_status 0x%x  phy_link_up %x line_speed %x\n",
		 gp_status, vars->phy_link_up, vars->line_speed);
	DP(NETIF_MSG_LINK, "duplex %x  flow_ctrl 0x%x link_status 0x%x\n",
		   vars->duplex, vars->flow_ctrl, vars->link_status);
	return rc;
}

static void bnx2x_set_gmii_tx_driver(struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	struct bnx2x_phy *phy = &params->phy[INT_PHY];
	u16 lp_up2;
	u16 tx_driver;
	u16 bank;

	/* read precomp */
	CL22_RD_OVER_CL45(bp, phy,
			  MDIO_REG_BANK_OVER_1G,
			  MDIO_OVER_1G_LP_UP2, &lp_up2);

	/* bits [10:7] at lp_up2, positioned at [15:12] */
	lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >>
		   MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) <<
		  MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT);

	if (lp_up2 == 0)
		return;

	for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3;
	      bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) {
		CL22_RD_OVER_CL45(bp, phy,
				  bank,
				  MDIO_TX0_TX_DRIVER, &tx_driver);

		/* replace tx_driver bits [15:12] */
		if (lp_up2 !=
		    (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) {
			tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
			tx_driver |= lp_up2;
			CL22_WR_OVER_CL45(bp, phy,
					  bank,
					  MDIO_TX0_TX_DRIVER, tx_driver);
		}
	}
}

static int bnx2x_emac_program(struct link_params *params,
			      struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;
	u16 mode = 0;

	DP(NETIF_MSG_LINK, "setting link speed & duplex\n");
	bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 +
		       EMAC_REG_EMAC_MODE,
		       (EMAC_MODE_25G_MODE |
			EMAC_MODE_PORT_MII_10M |
			EMAC_MODE_HALF_DUPLEX));
	switch (vars->line_speed) {
	case SPEED_10:
		mode |= EMAC_MODE_PORT_MII_10M;
		break;

	case SPEED_100:
		mode |= EMAC_MODE_PORT_MII;
		break;

	case SPEED_1000:
		mode |= EMAC_MODE_PORT_GMII;
		break;

	case SPEED_2500:
		mode |= (EMAC_MODE_25G_MODE | EMAC_MODE_PORT_GMII);
		break;

	default:
		/* 10G not valid for EMAC */
		DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
			   vars->line_speed);
		return -EINVAL;
	}

	if (vars->duplex == DUPLEX_HALF)
		mode |= EMAC_MODE_HALF_DUPLEX;
	bnx2x_bits_en(bp,
		      GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE,
		      mode);

	bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed);
	return 0;
}

static void bnx2x_set_preemphasis(struct bnx2x_phy *phy,
				  struct link_params *params)
{

	u16 bank, i = 0;
	struct bnx2x *bp = params->bp;

	for (bank = MDIO_REG_BANK_RX0, i = 0; bank <= MDIO_REG_BANK_RX3;
	      bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0), i++) {
			CL22_WR_OVER_CL45(bp, phy,
					  bank,
					  MDIO_RX0_RX_EQ_BOOST,
					  phy->rx_preemphasis[i]);
	}

	for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3;
		      bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0), i++) {
			CL22_WR_OVER_CL45(bp, phy,
					  bank,
					  MDIO_TX0_TX_DRIVER,
					  phy->tx_preemphasis[i]);
	}
}

static void bnx2x_init_internal_phy(struct bnx2x_phy *phy,
				    struct link_params *params,
				    struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u8 enable_cl73 = (SINGLE_MEDIA_DIRECT(params) ||
			  (params->loopback_mode == LOOPBACK_XGXS));
	if (!(vars->phy_flags & PHY_SGMII_FLAG)) {
		if (SINGLE_MEDIA_DIRECT(params) &&
		    (params->feature_config_flags &
		     FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED))
			bnx2x_set_preemphasis(phy, params);

		/* forced speed requested? */
		if (vars->line_speed != SPEED_AUTO_NEG ||
		    (SINGLE_MEDIA_DIRECT(params) &&
		     params->loopback_mode == LOOPBACK_EXT)) {
			DP(NETIF_MSG_LINK, "not SGMII, no AN\n");

			/* disable autoneg */
			bnx2x_set_autoneg(phy, params, vars, 0);

			/* program speed and duplex */
			bnx2x_program_serdes(phy, params, vars);

		} else { /* AN_mode */
			DP(NETIF_MSG_LINK, "not SGMII, AN\n");

			/* AN enabled */
			bnx2x_set_brcm_cl37_advertisment(phy, params);

			/* program duplex & pause advertisement (for aneg) */
			bnx2x_set_ieee_aneg_advertisment(phy, params,
							 vars->ieee_fc);

			/* enable autoneg */
			bnx2x_set_autoneg(phy, params, vars, enable_cl73);

			/* enable and restart AN */
			bnx2x_restart_autoneg(phy, params, enable_cl73);
		}

	} else { /* SGMII mode */
		DP(NETIF_MSG_LINK, "SGMII\n");

		bnx2x_initialize_sgmii_process(phy, params, vars);
	}
}

static int bnx2x_init_serdes(struct bnx2x_phy *phy,
			     struct link_params *params,
			     struct link_vars *vars)
{
	int rc;
	vars->phy_flags |= PHY_SGMII_FLAG;
	bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
	bnx2x_set_aer_mmd_serdes(params->bp, phy);
	rc = bnx2x_reset_unicore(params, phy, 1);
	/* reset the SerDes and wait for reset bit return low */
	if (rc != 0)
		return rc;
	bnx2x_set_aer_mmd_serdes(params->bp, phy);

	return rc;
}

static int bnx2x_init_xgxs(struct bnx2x_phy *phy,
			   struct link_params *params,
			   struct link_vars *vars)
{
	int rc;
	vars->phy_flags = PHY_XGXS_FLAG;
	if ((phy->req_line_speed &&
	     ((phy->req_line_speed == SPEED_100) ||
	      (phy->req_line_speed == SPEED_10))) ||
	    (!phy->req_line_speed &&
	     (phy->speed_cap_mask >=
	      PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) &&
	     (phy->speed_cap_mask <
	      PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
	     ))
		vars->phy_flags |= PHY_SGMII_FLAG;
	else
		vars->phy_flags &= ~PHY_SGMII_FLAG;

	bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
	bnx2x_set_aer_mmd_xgxs(params, phy);
	bnx2x_set_master_ln(params, phy);

	rc = bnx2x_reset_unicore(params, phy, 0);
	/* reset the SerDes and wait for reset bit return low */
	if (rc != 0)
		return rc;

	bnx2x_set_aer_mmd_xgxs(params, phy);

	/* setting the masterLn_def again after the reset */
	bnx2x_set_master_ln(params, phy);
	bnx2x_set_swap_lanes(params, phy);

	return rc;
}

static u16 bnx2x_wait_reset_complete(struct bnx2x *bp,
				     struct bnx2x_phy *phy,
				     struct link_params *params)
{
	u16 cnt, ctrl;
	/* Wait for soft reset to get cleared up to 1 sec */
	for (cnt = 0; cnt < 1000; cnt++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, &ctrl);
		if (!(ctrl & (1<<15)))
			break;
		msleep(1);
	}

	if (cnt == 1000)
		netdev_err(bp->dev,  "Warning: PHY was not initialized,"
				      " Port %d\n",
			 params->port);
	DP(NETIF_MSG_LINK, "control reg 0x%x (after %d ms)\n", ctrl, cnt);
	return cnt;
}

static void bnx2x_link_int_enable(struct link_params *params)
{
	u8 port = params->port;
	u32 mask;
	struct bnx2x *bp = params->bp;

	/* Setting the status to report on link up for either XGXS or SerDes */
	if (params->switch_cfg == SWITCH_CFG_10G) {
		mask = (NIG_MASK_XGXS0_LINK10G |
			NIG_MASK_XGXS0_LINK_STATUS);
		DP(NETIF_MSG_LINK, "enabled XGXS interrupt\n");
		if (!(SINGLE_MEDIA_DIRECT(params)) &&
			params->phy[INT_PHY].type !=
				PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) {
			mask |= NIG_MASK_MI_INT;
			DP(NETIF_MSG_LINK, "enabled external phy int\n");
		}

	} else { /* SerDes */
		mask = NIG_MASK_SERDES0_LINK_STATUS;
		DP(NETIF_MSG_LINK, "enabled SerDes interrupt\n");
		if (!(SINGLE_MEDIA_DIRECT(params)) &&
			params->phy[INT_PHY].type !=
				PORT_HW_CFG_SERDES_EXT_PHY_TYPE_NOT_CONN) {
			mask |= NIG_MASK_MI_INT;
			DP(NETIF_MSG_LINK, "enabled external phy int\n");
		}
	}
	bnx2x_bits_en(bp,
		      NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
		      mask);

	DP(NETIF_MSG_LINK, "port %x, is_xgxs %x, int_status 0x%x\n", port,
		 (params->switch_cfg == SWITCH_CFG_10G),
		 REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4));
	DP(NETIF_MSG_LINK, " int_mask 0x%x, MI_INT %x, SERDES_LINK %x\n",
		 REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
		 REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18),
		 REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS+port*0x3c));
	DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n",
	   REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
	   REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));
}

static void bnx2x_rearm_latch_signal(struct bnx2x *bp, u8 port,
				     u8 exp_mi_int)
{
	u32 latch_status = 0;

	/*
	 * Disable the MI INT ( external phy int ) by writing 1 to the
	 * status register. Link down indication is high-active-signal,
	 * so in this case we need to write the status to clear the XOR
	 */
	/* Read Latched signals */
	latch_status = REG_RD(bp,
				    NIG_REG_LATCH_STATUS_0 + port*8);
	DP(NETIF_MSG_LINK, "latch_status = 0x%x\n", latch_status);
	/* Handle only those with latched-signal=up.*/
	if (exp_mi_int)
		bnx2x_bits_en(bp,
			      NIG_REG_STATUS_INTERRUPT_PORT0
			      + port*4,
			      NIG_STATUS_EMAC0_MI_INT);
	else
		bnx2x_bits_dis(bp,
			       NIG_REG_STATUS_INTERRUPT_PORT0
			       + port*4,
			       NIG_STATUS_EMAC0_MI_INT);

	if (latch_status & 1) {

		/* For all latched-signal=up : Re-Arm Latch signals */
		REG_WR(bp, NIG_REG_LATCH_STATUS_0 + port*8,
		       (latch_status & 0xfffe) | (latch_status & 1));
	}
	/* For all latched-signal=up,Write original_signal to status */
}

static void bnx2x_link_int_ack(struct link_params *params,
			       struct link_vars *vars, u8 is_10g)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;

	/*
	 * First reset all status we assume only one line will be
	 * change at a time
	 */
	bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
		       (NIG_STATUS_XGXS0_LINK10G |
			NIG_STATUS_XGXS0_LINK_STATUS |
			NIG_STATUS_SERDES0_LINK_STATUS));
	if (vars->phy_link_up) {
		if (is_10g) {
			/*
			 * Disable the 10G link interrupt by writing 1 to the
			 * status register
			 */
			DP(NETIF_MSG_LINK, "10G XGXS phy link up\n");
			bnx2x_bits_en(bp,
				      NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
				      NIG_STATUS_XGXS0_LINK10G);

		} else if (params->switch_cfg == SWITCH_CFG_10G) {
			/*
			 * Disable the link interrupt by writing 1 to the
			 * relevant lane in the status register
			 */
			u32 ser_lane = ((params->lane_config &
				    PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
				    PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);

			DP(NETIF_MSG_LINK, "%d speed XGXS phy link up\n",
				 vars->line_speed);
			bnx2x_bits_en(bp,
				      NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
				      ((1 << ser_lane) <<
				       NIG_STATUS_XGXS0_LINK_STATUS_SIZE));

		} else { /* SerDes */
			DP(NETIF_MSG_LINK, "SerDes phy link up\n");
			/*
			 * Disable the link interrupt by writing 1 to the status
			 * register
			 */
			bnx2x_bits_en(bp,
				      NIG_REG_STATUS_INTERRUPT_PORT0 + port*4,
				      NIG_STATUS_SERDES0_LINK_STATUS);
		}

	}
}

static int bnx2x_format_ver(u32 num, u8 *str, u16 *len)
{
	u8 *str_ptr = str;
	u32 mask = 0xf0000000;
	u8 shift = 8*4;
	u8 digit;
	u8 remove_leading_zeros = 1;
	if (*len < 10) {
		/* Need more than 10chars for this format */
		*str_ptr = '\0';
		(*len)--;
		return -EINVAL;
	}
	while (shift > 0) {

		shift -= 4;
		digit = ((num & mask) >> shift);
		if (digit == 0 && remove_leading_zeros) {
			mask = mask >> 4;
			continue;
		} else if (digit < 0xa)
			*str_ptr = digit + '0';
		else
			*str_ptr = digit - 0xa + 'a';
		remove_leading_zeros = 0;
		str_ptr++;
		(*len)--;
		mask = mask >> 4;
		if (shift == 4*4) {
			*str_ptr = '.';
			str_ptr++;
			(*len)--;
			remove_leading_zeros = 1;
		}
	}
	return 0;
}


static int bnx2x_null_format_ver(u32 spirom_ver, u8 *str, u16 *len)
{
	str[0] = '\0';
	(*len)--;
	return 0;
}

int bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded,
				 u8 *version, u16 len)
{
	struct bnx2x *bp;
	u32 spirom_ver = 0;
	int status = 0;
	u8 *ver_p = version;
	u16 remain_len = len;
	if (version == NULL || params == NULL)
		return -EINVAL;
	bp = params->bp;

	/* Extract first external phy*/
	version[0] = '\0';
	spirom_ver = REG_RD(bp, params->phy[EXT_PHY1].ver_addr);

	if (params->phy[EXT_PHY1].format_fw_ver) {
		status |= params->phy[EXT_PHY1].format_fw_ver(spirom_ver,
							      ver_p,
							      &remain_len);
		ver_p += (len - remain_len);
	}
	if ((params->num_phys == MAX_PHYS) &&
	    (params->phy[EXT_PHY2].ver_addr != 0)) {
		spirom_ver = REG_RD(bp, params->phy[EXT_PHY2].ver_addr);
		if (params->phy[EXT_PHY2].format_fw_ver) {
			*ver_p = '/';
			ver_p++;
			remain_len--;
			status |= params->phy[EXT_PHY2].format_fw_ver(
				spirom_ver,
				ver_p,
				&remain_len);
			ver_p = version + (len - remain_len);
		}
	}
	*ver_p = '\0';
	return status;
}

static void bnx2x_set_xgxs_loopback(struct bnx2x_phy *phy,
				    struct link_params *params)
{
	u8 port = params->port;
	struct bnx2x *bp = params->bp;

	if (phy->req_line_speed != SPEED_1000) {
		u32 md_devad;

		DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n");

		/* change the uni_phy_addr in the nig */
		md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD +
				       port*0x18));

		REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 0x5);

		bnx2x_cl45_write(bp, phy,
				 5,
				 (MDIO_REG_BANK_AER_BLOCK +
				  (MDIO_AER_BLOCK_AER_REG & 0xf)),
				 0x2800);

		bnx2x_cl45_write(bp, phy,
				 5,
				 (MDIO_REG_BANK_CL73_IEEEB0 +
				  (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
				 0x6041);
		msleep(200);
		/* set aer mmd back */
		bnx2x_set_aer_mmd_xgxs(params, phy);

		/* and md_devad */
		REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, md_devad);
	} else {
		u16 mii_ctrl;
		DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n");
		bnx2x_cl45_read(bp, phy, 5,
				(MDIO_REG_BANK_COMBO_IEEE0 +
				(MDIO_COMBO_IEEE0_MII_CONTROL & 0xf)),
				&mii_ctrl);
		bnx2x_cl45_write(bp, phy, 5,
				 (MDIO_REG_BANK_COMBO_IEEE0 +
				 (MDIO_COMBO_IEEE0_MII_CONTROL & 0xf)),
				 mii_ctrl |
				 MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK);
	}
}

int bnx2x_set_led(struct link_params *params,
		  struct link_vars *vars, u8 mode, u32 speed)
{
	u8 port = params->port;
	u16 hw_led_mode = params->hw_led_mode;
	int rc = 0;
	u8 phy_idx;
	u32 tmp;
	u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "bnx2x_set_led: port %x, mode %d\n", port, mode);
	DP(NETIF_MSG_LINK, "speed 0x%x, hw_led_mode 0x%x\n",
		 speed, hw_led_mode);
	/* In case */
	for (phy_idx = EXT_PHY1; phy_idx < MAX_PHYS; phy_idx++) {
		if (params->phy[phy_idx].set_link_led) {
			params->phy[phy_idx].set_link_led(
				&params->phy[phy_idx], params, mode);
		}
	}

	switch (mode) {
	case LED_MODE_FRONT_PANEL_OFF:
	case LED_MODE_OFF:
		REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0);
		REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4,
		       SHARED_HW_CFG_LED_MAC1);

		tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
		EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE));
		break;

	case LED_MODE_OPER:
		/*
		 * For all other phys, OPER mode is same as ON, so in case
		 * link is down, do nothing
		 */
		if (!vars->link_up)
			break;
	case LED_MODE_ON:
		if (((params->phy[EXT_PHY1].type ==
			  PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) ||
			 (params->phy[EXT_PHY1].type ==
			  PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722)) &&
		    CHIP_IS_E2(bp) && params->num_phys == 2) {
			/*
			 * This is a work-around for E2+8727 Configurations
			 */
			if (mode == LED_MODE_ON ||
				speed == SPEED_10000){
				REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0);
				REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1);

				tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
				EMAC_WR(bp, EMAC_REG_EMAC_LED,
					(tmp | EMAC_LED_OVERRIDE));
				return rc;
			}
		} else if (SINGLE_MEDIA_DIRECT(params)) {
			/*
			 * This is a work-around for HW issue found when link
			 * is up in CL73
			 */
			REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0);
			REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1);
		} else {
			REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, hw_led_mode);
		}

		REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + port*4, 0);
		/* Set blinking rate to ~15.9Hz */
		REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4,
		       LED_BLINK_RATE_VAL);
		REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 +
		       port*4, 1);
		tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED);
		EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp & (~EMAC_LED_OVERRIDE)));

		if (CHIP_IS_E1(bp) &&
		    ((speed == SPEED_2500) ||
		     (speed == SPEED_1000) ||
		     (speed == SPEED_100) ||
		     (speed == SPEED_10))) {
			/*
			 * On Everest 1 Ax chip versions for speeds less than
			 * 10G LED scheme is different
			 */
			REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0
			       + port*4, 1);
			REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 +
			       port*4, 0);
			REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 +
			       port*4, 1);
		}
		break;

	default:
		rc = -EINVAL;
		DP(NETIF_MSG_LINK, "bnx2x_set_led: Invalid led mode %d\n",
			 mode);
		break;
	}
	return rc;

}

/*
 * This function comes to reflect the actual link state read DIRECTLY from the
 * HW
 */
int bnx2x_test_link(struct link_params *params, struct link_vars *vars,
		    u8 is_serdes)
{
	struct bnx2x *bp = params->bp;
	u16 gp_status = 0, phy_index = 0;
	u8 ext_phy_link_up = 0, serdes_phy_type;
	struct link_vars temp_vars;

	CL22_RD_OVER_CL45(bp, &params->phy[INT_PHY],
			  MDIO_REG_BANK_GP_STATUS,
			  MDIO_GP_STATUS_TOP_AN_STATUS1,
			  &gp_status);
	/* link is up only if both local phy and external phy are up */
	if (!(gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS))
		return -ESRCH;

	switch (params->num_phys) {
	case 1:
		/* No external PHY */
		return 0;
	case 2:
		ext_phy_link_up = params->phy[EXT_PHY1].read_status(
			&params->phy[EXT_PHY1],
			params, &temp_vars);
		break;
	case 3: /* Dual Media */
		for (phy_index = EXT_PHY1; phy_index < params->num_phys;
		      phy_index++) {
			serdes_phy_type = ((params->phy[phy_index].media_type ==
					    ETH_PHY_SFP_FIBER) ||
					   (params->phy[phy_index].media_type ==
					    ETH_PHY_XFP_FIBER) ||
					   (params->phy[phy_index].media_type ==
					    ETH_PHY_DA_TWINAX));

			if (is_serdes != serdes_phy_type)
				continue;
			if (params->phy[phy_index].read_status) {
				ext_phy_link_up |=
					params->phy[phy_index].read_status(
						&params->phy[phy_index],
						params, &temp_vars);
			}
		}
		break;
	}
	if (ext_phy_link_up)
		return 0;
	return -ESRCH;
}

static int bnx2x_link_initialize(struct link_params *params,
				 struct link_vars *vars)
{
	int rc = 0;
	u8 phy_index, non_ext_phy;
	struct bnx2x *bp = params->bp;
	/*
	 * In case of external phy existence, the line speed would be the
	 * line speed linked up by the external phy. In case it is direct
	 * only, then the line_speed during initialization will be
	 * equal to the req_line_speed
	 */
	vars->line_speed = params->phy[INT_PHY].req_line_speed;

	/*
	 * Initialize the internal phy in case this is a direct board
	 * (no external phys), or this board has external phy which requires
	 * to first.
	 */

	if (params->phy[INT_PHY].config_init)
		params->phy[INT_PHY].config_init(
			&params->phy[INT_PHY],
			params, vars);

	/* init ext phy and enable link state int */
	non_ext_phy = (SINGLE_MEDIA_DIRECT(params) ||
		       (params->loopback_mode == LOOPBACK_XGXS));

	if (non_ext_phy ||
	    (params->phy[EXT_PHY1].flags & FLAGS_INIT_XGXS_FIRST) ||
	    (params->loopback_mode == LOOPBACK_EXT_PHY)) {
		struct bnx2x_phy *phy = &params->phy[INT_PHY];
		if (vars->line_speed == SPEED_AUTO_NEG)
			bnx2x_set_parallel_detection(phy, params);
		bnx2x_init_internal_phy(phy, params, vars);
	}

	/* Init external phy*/
	if (!non_ext_phy)
		for (phy_index = EXT_PHY1; phy_index < params->num_phys;
		      phy_index++) {
			/*
			 * No need to initialize second phy in case of first
			 * phy only selection. In case of second phy, we do
			 * need to initialize the first phy, since they are
			 * connected.
			 */
			if (phy_index == EXT_PHY2 &&
			    (bnx2x_phy_selection(params) ==
			     PORT_HW_CFG_PHY_SELECTION_FIRST_PHY)) {
				DP(NETIF_MSG_LINK, "Ignoring second phy\n");
				continue;
			}
			params->phy[phy_index].config_init(
				&params->phy[phy_index],
				params, vars);
		}

	/* Reset the interrupt indication after phy was initialized */
	bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 +
		       params->port*4,
		       (NIG_STATUS_XGXS0_LINK10G |
			NIG_STATUS_XGXS0_LINK_STATUS |
			NIG_STATUS_SERDES0_LINK_STATUS |
			NIG_MASK_MI_INT));
	return rc;
}

static void bnx2x_int_link_reset(struct bnx2x_phy *phy,
				 struct link_params *params)
{
	/* reset the SerDes/XGXS */
	REG_WR(params->bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR,
	       (0x1ff << (params->port*16)));
}

static void bnx2x_common_ext_link_reset(struct bnx2x_phy *phy,
					struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u8 gpio_port;
	/* HW reset */
	if (CHIP_IS_E2(bp))
		gpio_port = BP_PATH(bp);
	else
		gpio_port = params->port;
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW,
		       gpio_port);
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW,
		       gpio_port);
	DP(NETIF_MSG_LINK, "reset external PHY\n");
}

static int bnx2x_update_link_down(struct link_params *params,
				  struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;

	DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port);
	bnx2x_set_led(params, vars, LED_MODE_OFF, 0);

	/* indicate no mac active */
	vars->mac_type = MAC_TYPE_NONE;

	/* update shared memory */
	vars->link_status = 0;
	vars->line_speed = 0;
	bnx2x_update_mng(params, vars->link_status);

	/* activate nig drain */
	REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);

	/* disable emac */
	REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);

	msleep(10);

	/* reset BigMac */
	bnx2x_bmac_rx_disable(bp, params->port);
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
	       (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
	return 0;
}

static int bnx2x_update_link_up(struct link_params *params,
				struct link_vars *vars,
				u8 link_10g)
{
	struct bnx2x *bp = params->bp;
	u8 port = params->port;
	int rc = 0;

	vars->link_status |= LINK_STATUS_LINK_UP;

	if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
		vars->link_status |=
			LINK_STATUS_TX_FLOW_CONTROL_ENABLED;

	if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
		vars->link_status |=
			LINK_STATUS_RX_FLOW_CONTROL_ENABLED;

	if (link_10g) {
		bnx2x_bmac_enable(params, vars, 0);
		bnx2x_set_led(params, vars,
			      LED_MODE_OPER, SPEED_10000);
	} else {
		rc = bnx2x_emac_program(params, vars);

		bnx2x_emac_enable(params, vars, 0);

		/* AN complete? */
		if ((vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE)
		    && (!(vars->phy_flags & PHY_SGMII_FLAG)) &&
		    SINGLE_MEDIA_DIRECT(params))
			bnx2x_set_gmii_tx_driver(params);
	}

	/* PBF - link up */
	if (!(CHIP_IS_E2(bp)))
		rc |= bnx2x_pbf_update(params, vars->flow_ctrl,
				       vars->line_speed);

	/* disable drain */
	REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0);

	/* update shared memory */
	bnx2x_update_mng(params, vars->link_status);
	msleep(20);
	return rc;
}
/*
 * The bnx2x_link_update function should be called upon link
 * interrupt.
 * Link is considered up as follows:
 * - DIRECT_SINGLE_MEDIA - Only XGXS link (internal link) needs
 *   to be up
 * - SINGLE_MEDIA - The link between the 577xx and the external
 *   phy (XGXS) need to up as well as the external link of the
 *   phy (PHY_EXT1)
 * - DUAL_MEDIA - The link between the 577xx and the first
 *   external phy needs to be up, and at least one of the 2
 *   external phy link must be up.
 */
int bnx2x_link_update(struct link_params *params, struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	struct link_vars phy_vars[MAX_PHYS];
	u8 port = params->port;
	u8 link_10g, phy_index;
	u8 ext_phy_link_up = 0, cur_link_up;
	int rc = 0;
	u8 is_mi_int = 0;
	u16 ext_phy_line_speed = 0, prev_line_speed = vars->line_speed;
	u8 active_external_phy = INT_PHY;
	vars->link_status = 0;
	for (phy_index = INT_PHY; phy_index < params->num_phys;
	      phy_index++) {
		phy_vars[phy_index].flow_ctrl = 0;
		phy_vars[phy_index].link_status = 0;
		phy_vars[phy_index].line_speed = 0;
		phy_vars[phy_index].duplex = DUPLEX_FULL;
		phy_vars[phy_index].phy_link_up = 0;
		phy_vars[phy_index].link_up = 0;
	}

	DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n",
		 port, (vars->phy_flags & PHY_XGXS_FLAG),
		 REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4));

	is_mi_int = (u8)(REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT +
				port*0x18) > 0);
	DP(NETIF_MSG_LINK, "int_mask 0x%x MI_INT %x, SERDES_LINK %x\n",
		 REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4),
		 is_mi_int,
		 REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c));

	DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n",
	  REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
	  REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));

	/* disable emac */
	REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);

	/*
	 * Step 1:
	 * Check external link change only for external phys, and apply
	 * priority selection between them in case the link on both phys
	 * is up. Note that the instead of the common vars, a temporary
	 * vars argument is used since each phy may have different link/
	 * speed/duplex result
	 */
	for (phy_index = EXT_PHY1; phy_index < params->num_phys;
	      phy_index++) {
		struct bnx2x_phy *phy = &params->phy[phy_index];
		if (!phy->read_status)
			continue;
		/* Read link status and params of this ext phy */
		cur_link_up = phy->read_status(phy, params,
					       &phy_vars[phy_index]);
		if (cur_link_up) {
			DP(NETIF_MSG_LINK, "phy in index %d link is up\n",
				   phy_index);
		} else {
			DP(NETIF_MSG_LINK, "phy in index %d link is down\n",
				   phy_index);
			continue;
		}

		if (!ext_phy_link_up) {
			ext_phy_link_up = 1;
			active_external_phy = phy_index;
		} else {
			switch (bnx2x_phy_selection(params)) {
			case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT:
			case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
			/*
			 * In this option, the first PHY makes sure to pass the
			 * traffic through itself only.
			 * Its not clear how to reset the link on the second phy
			 */
				active_external_phy = EXT_PHY1;
				break;
			case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
			/*
			 * In this option, the first PHY makes sure to pass the
			 * traffic through the second PHY.
			 */
				active_external_phy = EXT_PHY2;
				break;
			default:
			/*
			 * Link indication on both PHYs with the following cases
			 * is invalid:
			 * - FIRST_PHY means that second phy wasn't initialized,
			 * hence its link is expected to be down
			 * - SECOND_PHY means that first phy should not be able
			 * to link up by itself (using configuration)
			 * - DEFAULT should be overriden during initialiazation
			 */
				DP(NETIF_MSG_LINK, "Invalid link indication"
					   "mpc=0x%x. DISABLING LINK !!!\n",
					   params->multi_phy_config);
				ext_phy_link_up = 0;
				break;
			}
		}
	}
	prev_line_speed = vars->line_speed;
	/*
	 * Step 2:
	 * Read the status of the internal phy. In case of
	 * DIRECT_SINGLE_MEDIA board, this link is the external link,
	 * otherwise this is the link between the 577xx and the first
	 * external phy
	 */
	if (params->phy[INT_PHY].read_status)
		params->phy[INT_PHY].read_status(
			&params->phy[INT_PHY],
			params, vars);
	/*
	 * The INT_PHY flow control reside in the vars. This include the
	 * case where the speed or flow control are not set to AUTO.
	 * Otherwise, the active external phy flow control result is set
	 * to the vars. The ext_phy_line_speed is needed to check if the
	 * speed is different between the internal phy and external phy.
	 * This case may be result of intermediate link speed change.
	 */
	if (active_external_phy > INT_PHY) {
		vars->flow_ctrl = phy_vars[active_external_phy].flow_ctrl;
		/*
		 * Link speed is taken from the XGXS. AN and FC result from
		 * the external phy.
		 */
		vars->link_status |= phy_vars[active_external_phy].link_status;

		/*
		 * if active_external_phy is first PHY and link is up - disable
		 * disable TX on second external PHY
		 */
		if (active_external_phy == EXT_PHY1) {
			if (params->phy[EXT_PHY2].phy_specific_func) {
				DP(NETIF_MSG_LINK, "Disabling TX on"
						   " EXT_PHY2\n");
				params->phy[EXT_PHY2].phy_specific_func(
					&params->phy[EXT_PHY2],
					params, DISABLE_TX);
			}
		}

		ext_phy_line_speed = phy_vars[active_external_phy].line_speed;
		vars->duplex = phy_vars[active_external_phy].duplex;
		if (params->phy[active_external_phy].supported &
		    SUPPORTED_FIBRE)
			vars->link_status |= LINK_STATUS_SERDES_LINK;
		DP(NETIF_MSG_LINK, "Active external phy selected: %x\n",
			   active_external_phy);
	}

	for (phy_index = EXT_PHY1; phy_index < params->num_phys;
	      phy_index++) {
		if (params->phy[phy_index].flags &
		    FLAGS_REARM_LATCH_SIGNAL) {
			bnx2x_rearm_latch_signal(bp, port,
						 phy_index ==
						 active_external_phy);
			break;
		}
	}
	DP(NETIF_MSG_LINK, "vars->flow_ctrl = 0x%x, vars->link_status = 0x%x,"
		   " ext_phy_line_speed = %d\n", vars->flow_ctrl,
		   vars->link_status, ext_phy_line_speed);
	/*
	 * Upon link speed change set the NIG into drain mode. Comes to
	 * deals with possible FIFO glitch due to clk change when speed
	 * is decreased without link down indicator
	 */

	if (vars->phy_link_up) {
		if (!(SINGLE_MEDIA_DIRECT(params)) && ext_phy_link_up &&
		    (ext_phy_line_speed != vars->line_speed)) {
			DP(NETIF_MSG_LINK, "Internal link speed %d is"
				   " different than the external"
				   " link speed %d\n", vars->line_speed,
				   ext_phy_line_speed);
			vars->phy_link_up = 0;
		} else if (prev_line_speed != vars->line_speed) {
			REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4,
			       0);
			msleep(1);
		}
	}

	/* anything 10 and over uses the bmac */
	link_10g = ((vars->line_speed == SPEED_10000) ||
		    (vars->line_speed == SPEED_12000) ||
		    (vars->line_speed == SPEED_12500) ||
		    (vars->line_speed == SPEED_13000) ||
		    (vars->line_speed == SPEED_15000) ||
		    (vars->line_speed == SPEED_16000));

	bnx2x_link_int_ack(params, vars, link_10g);

	/*
	 * In case external phy link is up, and internal link is down
	 * (not initialized yet probably after link initialization, it
	 * needs to be initialized.
	 * Note that after link down-up as result of cable plug, the xgxs
	 * link would probably become up again without the need
	 * initialize it
	 */
	if (!(SINGLE_MEDIA_DIRECT(params))) {
		DP(NETIF_MSG_LINK, "ext_phy_link_up = %d, int_link_up = %d,"
			   " init_preceding = %d\n", ext_phy_link_up,
			   vars->phy_link_up,
			   params->phy[EXT_PHY1].flags &
			   FLAGS_INIT_XGXS_FIRST);
		if (!(params->phy[EXT_PHY1].flags &
		      FLAGS_INIT_XGXS_FIRST)
		    && ext_phy_link_up && !vars->phy_link_up) {
			vars->line_speed = ext_phy_line_speed;
			if (vars->line_speed < SPEED_1000)
				vars->phy_flags |= PHY_SGMII_FLAG;
			else
				vars->phy_flags &= ~PHY_SGMII_FLAG;
			bnx2x_init_internal_phy(&params->phy[INT_PHY],
						params,
						vars);
		}
	}
	/*
	 * Link is up only if both local phy and external phy (in case of
	 * non-direct board) are up
	 */
	vars->link_up = (vars->phy_link_up &&
			 (ext_phy_link_up ||
			  SINGLE_MEDIA_DIRECT(params)));

	if (vars->link_up)
		rc = bnx2x_update_link_up(params, vars, link_10g);
	else
		rc = bnx2x_update_link_down(params, vars);

	return rc;
}


/*****************************************************************************/
/*			    External Phy section			     */
/*****************************************************************************/
void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port)
{
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
	msleep(1);
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH, port);
}

static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port,
				      u32 spirom_ver, u32 ver_addr)
{
	DP(NETIF_MSG_LINK, "FW version 0x%x:0x%x for port %d\n",
		 (u16)(spirom_ver>>16), (u16)spirom_ver, port);

	if (ver_addr)
		REG_WR(bp, ver_addr, spirom_ver);
}

static void bnx2x_save_bcm_spirom_ver(struct bnx2x *bp,
				      struct bnx2x_phy *phy,
				      u8 port)
{
	u16 fw_ver1, fw_ver2;

	bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
			MDIO_PMA_REG_ROM_VER1, &fw_ver1);
	bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD,
			MDIO_PMA_REG_ROM_VER2, &fw_ver2);
	bnx2x_save_spirom_version(bp, port, (u32)(fw_ver1<<16 | fw_ver2),
				  phy->ver_addr);
}

static void bnx2x_ext_phy_set_pause(struct link_params *params,
				    struct bnx2x_phy *phy,
				    struct link_vars *vars)
{
	u16 val;
	struct bnx2x *bp = params->bp;
	/* read modify write pause advertizing */
	bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV_PAUSE, &val);

	val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH;

	/* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
	bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
	if ((vars->ieee_fc &
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
		val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC;
	}
	if ((vars->ieee_fc &
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) {
		val |= MDIO_AN_REG_ADV_PAUSE_PAUSE;
	}
	DP(NETIF_MSG_LINK, "Ext phy AN advertize 0x%x\n", val);
	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV_PAUSE, val);
}

static u8 bnx2x_ext_phy_resolve_fc(struct bnx2x_phy *phy,
				   struct link_params *params,
				   struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 ld_pause;		/* local */
	u16 lp_pause;		/* link partner */
	u16 pause_result;
	u8 ret = 0;
	/* read twice */

	vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;

	if (phy->req_flow_ctrl != BNX2X_FLOW_CTRL_AUTO)
		vars->flow_ctrl = phy->req_flow_ctrl;
	else if (phy->req_line_speed != SPEED_AUTO_NEG)
		vars->flow_ctrl = params->req_fc_auto_adv;
	else if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) {
		ret = 1;
		bnx2x_cl45_read(bp, phy,
				MDIO_AN_DEVAD,
				MDIO_AN_REG_ADV_PAUSE, &ld_pause);
		bnx2x_cl45_read(bp, phy,
				MDIO_AN_DEVAD,
				MDIO_AN_REG_LP_AUTO_NEG, &lp_pause);
		pause_result = (ld_pause &
				MDIO_AN_REG_ADV_PAUSE_MASK) >> 8;
		pause_result |= (lp_pause &
				 MDIO_AN_REG_ADV_PAUSE_MASK) >> 10;
		DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x\n",
		   pause_result);
		bnx2x_pause_resolve(vars, pause_result);
	}
	return ret;
}

static void bnx2x_ext_phy_10G_an_resolve(struct bnx2x *bp,
				       struct bnx2x_phy *phy,
				       struct link_vars *vars)
{
	u16 val;
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD,
			MDIO_AN_REG_STATUS, &val);
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD,
			MDIO_AN_REG_STATUS, &val);
	if (val & (1<<5))
		vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
	if ((val & (1<<0)) == 0)
		vars->link_status |= LINK_STATUS_PARALLEL_DETECTION_USED;
}

/******************************************************************/
/*		common BCM8073/BCM8727 PHY SECTION		  */
/******************************************************************/
static void bnx2x_8073_resolve_fc(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	if (phy->req_line_speed == SPEED_10 ||
	    phy->req_line_speed == SPEED_100) {
		vars->flow_ctrl = phy->req_flow_ctrl;
		return;
	}

	if (bnx2x_ext_phy_resolve_fc(phy, params, vars) &&
	    (vars->flow_ctrl == BNX2X_FLOW_CTRL_NONE)) {
		u16 pause_result;
		u16 ld_pause;		/* local */
		u16 lp_pause;		/* link partner */
		bnx2x_cl45_read(bp, phy,
				MDIO_AN_DEVAD,
				MDIO_AN_REG_CL37_FC_LD, &ld_pause);

		bnx2x_cl45_read(bp, phy,
				MDIO_AN_DEVAD,
				MDIO_AN_REG_CL37_FC_LP, &lp_pause);
		pause_result = (ld_pause &
				MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5;
		pause_result |= (lp_pause &
				 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7;

		bnx2x_pause_resolve(vars, pause_result);
		DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x\n",
			   pause_result);
	}
}
static int bnx2x_8073_8727_external_rom_boot(struct bnx2x *bp,
					     struct bnx2x_phy *phy,
					     u8 port)
{
	u32 count = 0;
	u16 fw_ver1, fw_msgout;
	int rc = 0;

	/* Boot port from external ROM  */
	/* EDC grst */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_GEN_CTRL,
			 0x0001);

	/* ucode reboot and rst */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_GEN_CTRL,
			 0x008c);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_MISC_CTRL1, 0x0001);

	/* Reset internal microprocessor */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_GEN_CTRL,
			 MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);

	/* Release srst bit */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_GEN_CTRL,
			 MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);

	/* Delay 100ms per the PHY specifications */
	msleep(100);

	/* 8073 sometimes taking longer to download */
	do {
		count++;
		if (count > 300) {
			DP(NETIF_MSG_LINK,
				 "bnx2x_8073_8727_external_rom_boot port %x:"
				 "Download failed. fw version = 0x%x\n",
				 port, fw_ver1);
			rc = -EINVAL;
			break;
		}

		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_ROM_VER1, &fw_ver1);
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_M8051_MSGOUT_REG, &fw_msgout);

		msleep(1);
	} while (fw_ver1 == 0 || fw_ver1 == 0x4321 ||
			((fw_msgout & 0xff) != 0x03 && (phy->type ==
			PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073)));

	/* Clear ser_boot_ctl bit */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_MISC_CTRL1, 0x0000);
	bnx2x_save_bcm_spirom_ver(bp, phy, port);

	DP(NETIF_MSG_LINK,
		 "bnx2x_8073_8727_external_rom_boot port %x:"
		 "Download complete. fw version = 0x%x\n",
		 port, fw_ver1);

	return rc;
}

/******************************************************************/
/*			BCM8073 PHY SECTION			  */
/******************************************************************/
static int bnx2x_8073_is_snr_needed(struct bnx2x *bp, struct bnx2x_phy *phy)
{
	/* This is only required for 8073A1, version 102 only */
	u16 val;

	/* Read 8073 HW revision*/
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_8073_CHIP_REV, &val);

	if (val != 1) {
		/* No need to workaround in 8073 A1 */
		return 0;
	}

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_ROM_VER2, &val);

	/* SNR should be applied only for version 0x102 */
	if (val != 0x102)
		return 0;

	return 1;
}

static int bnx2x_8073_xaui_wa(struct bnx2x *bp, struct bnx2x_phy *phy)
{
	u16 val, cnt, cnt1 ;

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_8073_CHIP_REV, &val);

	if (val > 0) {
		/* No need to workaround in 8073 A1 */
		return 0;
	}
	/* XAUI workaround in 8073 A0: */

	/*
	 * After loading the boot ROM and restarting Autoneg, poll
	 * Dev1, Reg $C820:
	 */

	for (cnt = 0; cnt < 1000; cnt++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
				&val);
		  /*
		   * If bit [14] = 0 or bit [13] = 0, continue on with
		   * system initialization (XAUI work-around not required, as
		   * these bits indicate 2.5G or 1G link up).
		   */
		if (!(val & (1<<14)) || !(val & (1<<13))) {
			DP(NETIF_MSG_LINK, "XAUI work-around not required\n");
			return 0;
		} else if (!(val & (1<<15))) {
			DP(NETIF_MSG_LINK, "bit 15 went off\n");
			/*
			 * If bit 15 is 0, then poll Dev1, Reg $C841 until it's
			 * MSB (bit15) goes to 1 (indicating that the XAUI
			 * workaround has completed), then continue on with
			 * system initialization.
			 */
			for (cnt1 = 0; cnt1 < 1000; cnt1++) {
				bnx2x_cl45_read(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8073_XAUI_WA, &val);
				if (val & (1<<15)) {
					DP(NETIF_MSG_LINK,
					  "XAUI workaround has completed\n");
					return 0;
				 }
				 msleep(3);
			}
			break;
		}
		msleep(3);
	}
	DP(NETIF_MSG_LINK, "Warning: XAUI work-around timeout !!!\n");
	return -EINVAL;
}

static void bnx2x_807x_force_10G(struct bnx2x *bp, struct bnx2x_phy *phy)
{
	/* Force KR or KX */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040);
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0x000b);
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_BCM_CTRL, 0x0000);
	bnx2x_cl45_write(bp, phy,
			 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x0000);
}

static void bnx2x_8073_set_pause_cl37(struct link_params *params,
				      struct bnx2x_phy *phy,
				      struct link_vars *vars)
{
	u16 cl37_val;
	struct bnx2x *bp = params->bp;
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, &cl37_val);

	cl37_val &= ~MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
	/* Please refer to Table 28B-3 of 802.3ab-1999 spec. */
	bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
	if ((vars->ieee_fc &
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) ==
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) {
		cl37_val |=  MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC;
	}
	if ((vars->ieee_fc &
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) ==
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) {
		cl37_val |=  MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC;
	}
	if ((vars->ieee_fc &
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) ==
	    MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) {
		cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH;
	}
	DP(NETIF_MSG_LINK,
		 "Ext phy AN advertize cl37 0x%x\n", cl37_val);

	bnx2x_cl45_write(bp, phy,
			 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, cl37_val);
	msleep(500);
}

static int bnx2x_8073_config_init(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 val = 0, tmp1;
	u8 gpio_port;
	DP(NETIF_MSG_LINK, "Init 8073\n");

	if (CHIP_IS_E2(bp))
		gpio_port = BP_PATH(bp);
	else
		gpio_port = params->port;
	/* Restore normal power mode*/
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);

	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);

	/* enable LASI */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM_CTRL, (1<<2));
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL,  0x0004);

	bnx2x_8073_set_pause_cl37(params, phy, vars);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &tmp1);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM, &tmp1);

	DP(NETIF_MSG_LINK, "Before rom RX_ALARM(port1): 0x%x\n", tmp1);

	/* Swap polarity if required - Must be done only in non-1G mode */
	if (params->lane_config & PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) {
		/* Configure the 8073 to swap _P and _N of the KR lines */
		DP(NETIF_MSG_LINK, "Swapping polarity for the 8073\n");
		/* 10G Rx/Tx and 1G Tx signal polarity swap */
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL, &val);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL,
				 (val | (3<<9)));
	}


	/* Enable CL37 BAM */
	if (REG_RD(bp, params->shmem_base +
			 offsetof(struct shmem_region, dev_info.
				  port_hw_config[params->port].default_cfg)) &
	    PORT_HW_CFG_ENABLE_BAM_ON_KR_ENABLED) {

		bnx2x_cl45_read(bp, phy,
				MDIO_AN_DEVAD,
				MDIO_AN_REG_8073_BAM, &val);
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD,
				 MDIO_AN_REG_8073_BAM, val | 1);
		DP(NETIF_MSG_LINK, "Enable CL37 BAM on KR\n");
	}
	if (params->loopback_mode == LOOPBACK_EXT) {
		bnx2x_807x_force_10G(bp, phy);
		DP(NETIF_MSG_LINK, "Forced speed 10G on 807X\n");
		return 0;
	} else {
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_BCM_CTRL, 0x0002);
	}
	if (phy->req_line_speed != SPEED_AUTO_NEG) {
		if (phy->req_line_speed == SPEED_10000) {
			val = (1<<7);
		} else if (phy->req_line_speed ==  SPEED_2500) {
			val = (1<<5);
			/*
			 * Note that 2.5G works only when used with 1G
			 * advertisement
			 */
		} else
			val = (1<<5);
	} else {
		val = 0;
		if (phy->speed_cap_mask &
			PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)
			val |= (1<<7);

		/* Note that 2.5G works only when used with 1G advertisement */
		if (phy->speed_cap_mask &
			(PORT_HW_CFG_SPEED_CAPABILITY_D0_1G |
			 PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G))
			val |= (1<<5);
		DP(NETIF_MSG_LINK, "807x autoneg val = 0x%x\n", val);
	}

	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV, val);
	bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_8073_2_5G, &tmp1);

	if (((phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) &&
	     (phy->req_line_speed == SPEED_AUTO_NEG)) ||
	    (phy->req_line_speed == SPEED_2500)) {
		u16 phy_ver;
		/* Allow 2.5G for A1 and above */
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD, MDIO_PMA_REG_8073_CHIP_REV,
				&phy_ver);
		DP(NETIF_MSG_LINK, "Add 2.5G\n");
		if (phy_ver > 0)
			tmp1 |= 1;
		else
			tmp1 &= 0xfffe;
	} else {
		DP(NETIF_MSG_LINK, "Disable 2.5G\n");
		tmp1 &= 0xfffe;
	}

	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_8073_2_5G, tmp1);
	/* Add support for CL37 (passive mode) II */

	bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, &tmp1);
	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD,
			 (tmp1 | ((phy->req_duplex == DUPLEX_FULL) ?
				  0x20 : 0x40)));

	/* Add support for CL37 (passive mode) III */
	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000);

	/*
	 * The SNR will improve about 2db by changing BW and FEE main
	 * tap. Rest commands are executed after link is up
	 * Change FFE main cursor to 5 in EDC register
	 */
	if (bnx2x_8073_is_snr_needed(bp, phy))
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_EDC_FFE_MAIN,
				 0xFB0C);

	/* Enable FEC (Forware Error Correction) Request in the AN */
	bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV2, &tmp1);
	tmp1 |= (1<<15);
	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV2, tmp1);

	bnx2x_ext_phy_set_pause(params, phy, vars);

	/* Restart autoneg */
	msleep(500);
	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200);
	DP(NETIF_MSG_LINK, "807x Autoneg Restart: Advertise 1G=%x, 10G=%x\n",
		   ((val & (1<<5)) > 0), ((val & (1<<7)) > 0));
	return 0;
}

static u8 bnx2x_8073_read_status(struct bnx2x_phy *phy,
				 struct link_params *params,
				 struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u8 link_up = 0;
	u16 val1, val2;
	u16 link_status = 0;
	u16 an1000_status = 0;

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val1);

	DP(NETIF_MSG_LINK, "8703 LASI status 0x%x\n", val1);

	/* clear the interrupt LASI status register */
	bnx2x_cl45_read(bp, phy,
			MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val2);
	bnx2x_cl45_read(bp, phy,
			MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val1);
	DP(NETIF_MSG_LINK, "807x PCS status 0x%x->0x%x\n", val2, val1);
	/* Clear MSG-OUT */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &val1);

	/* Check the LASI */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM, &val2);

	DP(NETIF_MSG_LINK, "KR 0x9003 0x%x\n", val2);

	/* Check the link status */
	bnx2x_cl45_read(bp, phy,
			MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val2);
	DP(NETIF_MSG_LINK, "KR PCS status 0x%x\n", val2);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1);
	link_up = ((val1 & 4) == 4);
	DP(NETIF_MSG_LINK, "PMA_REG_STATUS=0x%x\n", val1);

	if (link_up &&
	     ((phy->req_line_speed != SPEED_10000))) {
		if (bnx2x_8073_xaui_wa(bp, phy) != 0)
			return 0;
	}
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &an1000_status);
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &an1000_status);

	/* Check the link status on 1.1.2 */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1);
	DP(NETIF_MSG_LINK, "KR PMA status 0x%x->0x%x,"
		   "an_link_status=0x%x\n", val2, val1, an1000_status);

	link_up = (((val1 & 4) == 4) || (an1000_status & (1<<1)));
	if (link_up && bnx2x_8073_is_snr_needed(bp, phy)) {
		/*
		 * The SNR will improve about 2dbby changing the BW and FEE main
		 * tap. The 1st write to change FFE main tap is set before
		 * restart AN. Change PLL Bandwidth in EDC register
		 */
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_PLL_BANDWIDTH,
				 0x26BC);

		/* Change CDR Bandwidth in EDC register */
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_CDR_BANDWIDTH,
				 0x0333);
	}
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
			&link_status);

	/* Bits 0..2 --> speed detected, bits 13..15--> link is down */
	if ((link_status & (1<<2)) && (!(link_status & (1<<15)))) {
		link_up = 1;
		vars->line_speed = SPEED_10000;
		DP(NETIF_MSG_LINK, "port %x: External link up in 10G\n",
			   params->port);
	} else if ((link_status & (1<<1)) && (!(link_status & (1<<14)))) {
		link_up = 1;
		vars->line_speed = SPEED_2500;
		DP(NETIF_MSG_LINK, "port %x: External link up in 2.5G\n",
			   params->port);
	} else if ((link_status & (1<<0)) && (!(link_status & (1<<13)))) {
		link_up = 1;
		vars->line_speed = SPEED_1000;
		DP(NETIF_MSG_LINK, "port %x: External link up in 1G\n",
			   params->port);
	} else {
		link_up = 0;
		DP(NETIF_MSG_LINK, "port %x: External link is down\n",
			   params->port);
	}

	if (link_up) {
		/* Swap polarity if required */
		if (params->lane_config &
		    PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) {
			/* Configure the 8073 to swap P and N of the KR lines */
			bnx2x_cl45_read(bp, phy,
					MDIO_XS_DEVAD,
					MDIO_XS_REG_8073_RX_CTRL_PCIE, &val1);
			/*
			 * Set bit 3 to invert Rx in 1G mode and clear this bit
			 * when it`s in 10G mode.
			 */
			if (vars->line_speed == SPEED_1000) {
				DP(NETIF_MSG_LINK, "Swapping 1G polarity for"
					      "the 8073\n");
				val1 |= (1<<3);
			} else
				val1 &= ~(1<<3);

			bnx2x_cl45_write(bp, phy,
					 MDIO_XS_DEVAD,
					 MDIO_XS_REG_8073_RX_CTRL_PCIE,
					 val1);
		}
		bnx2x_ext_phy_10G_an_resolve(bp, phy, vars);
		bnx2x_8073_resolve_fc(phy, params, vars);
		vars->duplex = DUPLEX_FULL;
	}
	return link_up;
}

static void bnx2x_8073_link_reset(struct bnx2x_phy *phy,
				  struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u8 gpio_port;
	if (CHIP_IS_E2(bp))
		gpio_port = BP_PATH(bp);
	else
		gpio_port = params->port;
	DP(NETIF_MSG_LINK, "Setting 8073 port %d into low power mode\n",
	   gpio_port);
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW,
		       gpio_port);
}

/******************************************************************/
/*			BCM8705 PHY SECTION			  */
/******************************************************************/
static int bnx2x_8705_config_init(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "init 8705\n");
	/* Restore normal power mode*/
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
	/* HW reset */
	bnx2x_ext_phy_hw_reset(bp, params->port);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
	bnx2x_wait_reset_complete(bp, phy, params);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL, 0x8288);
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, 0x7fbf);
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_CMU_PLL_BYPASS, 0x0100);
	bnx2x_cl45_write(bp, phy,
			 MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_CNTL, 0x1);
	/* BCM8705 doesn't have microcode, hence the 0 */
	bnx2x_save_spirom_version(bp, params->port, params->shmem_base, 0);
	return 0;
}

static u8 bnx2x_8705_read_status(struct bnx2x_phy *phy,
				 struct link_params *params,
				 struct link_vars *vars)
{
	u8 link_up = 0;
	u16 val1, rx_sd;
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "read status 8705\n");
	bnx2x_cl45_read(bp, phy,
		      MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_STATUS, &val1);
	DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);

	bnx2x_cl45_read(bp, phy,
		      MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_STATUS, &val1);
	DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1);

	bnx2x_cl45_read(bp, phy,
		      MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD, &rx_sd);

	bnx2x_cl45_read(bp, phy,
		      MDIO_PMA_DEVAD, 0xc809, &val1);
	bnx2x_cl45_read(bp, phy,
		      MDIO_PMA_DEVAD, 0xc809, &val1);

	DP(NETIF_MSG_LINK, "8705 1.c809 val=0x%x\n", val1);
	link_up = ((rx_sd & 0x1) && (val1 & (1<<9)) && ((val1 & (1<<8)) == 0));
	if (link_up) {
		vars->line_speed = SPEED_10000;
		bnx2x_ext_phy_resolve_fc(phy, params, vars);
	}
	return link_up;
}

/******************************************************************/
/*			SFP+ module Section			  */
/******************************************************************/
static u8 bnx2x_get_gpio_port(struct link_params *params)
{
	u8 gpio_port;
	u32 swap_val, swap_override;
	struct bnx2x *bp = params->bp;
	if (CHIP_IS_E2(bp))
		gpio_port = BP_PATH(bp);
	else
		gpio_port = params->port;
	swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
	swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
	return gpio_port ^ (swap_val && swap_override);
}
static void bnx2x_sfp_set_transmitter(struct link_params *params,
				      struct bnx2x_phy *phy,
				      u8 tx_en)
{
	u16 val;
	u8 port = params->port;
	struct bnx2x *bp = params->bp;
	u32 tx_en_mode;

	/* Disable/Enable transmitter ( TX laser of the SFP+ module.)*/
	tx_en_mode = REG_RD(bp, params->shmem_base +
			    offsetof(struct shmem_region,
				     dev_info.port_hw_config[port].sfp_ctrl)) &
		PORT_HW_CFG_TX_LASER_MASK;
	DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x "
			   "mode = %x\n", tx_en, port, tx_en_mode);
	switch (tx_en_mode) {
	case PORT_HW_CFG_TX_LASER_MDIO:

		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_PHY_IDENTIFIER,
				&val);

		if (tx_en)
			val &= ~(1<<15);
		else
			val |= (1<<15);

		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_PHY_IDENTIFIER,
				 val);
	break;
	case PORT_HW_CFG_TX_LASER_GPIO0:
	case PORT_HW_CFG_TX_LASER_GPIO1:
	case PORT_HW_CFG_TX_LASER_GPIO2:
	case PORT_HW_CFG_TX_LASER_GPIO3:
	{
		u16 gpio_pin;
		u8 gpio_port, gpio_mode;
		if (tx_en)
			gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_HIGH;
		else
			gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_LOW;

		gpio_pin = tx_en_mode - PORT_HW_CFG_TX_LASER_GPIO0;
		gpio_port = bnx2x_get_gpio_port(params);
		bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port);
		break;
	}
	default:
		DP(NETIF_MSG_LINK, "Invalid TX_LASER_MDIO 0x%x\n", tx_en_mode);
		break;
	}
}

static int bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy,
					     struct link_params *params,
					     u16 addr, u8 byte_cnt, u8 *o_buf)
{
	struct bnx2x *bp = params->bp;
	u16 val = 0;
	u16 i;
	if (byte_cnt > 16) {
		DP(NETIF_MSG_LINK, "Reading from eeprom is"
			    " is limited to 0xf\n");
		return -EINVAL;
	}
	/* Set the read command byte count */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
			 (byte_cnt | 0xa000));

	/* Set the read command address */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
			 addr);

	/* Activate read command */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
			 0x2c0f);

	/* Wait up to 500us for command complete status */
	for (i = 0; i < 100; i++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
		if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
		    MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
			break;
		udelay(5);
	}

	if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) !=
		    MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) {
		DP(NETIF_MSG_LINK,
			 "Got bad status 0x%x when reading from SFP+ EEPROM\n",
			 (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK));
		return -EINVAL;
	}

	/* Read the buffer */
	for (i = 0; i < byte_cnt; i++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val);
		o_buf[i] = (u8)(val & MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK);
	}

	for (i = 0; i < 100; i++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
		if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
		    MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
			return 0;
		msleep(1);
	}
	return -EINVAL;
}

static int bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy,
					     struct link_params *params,
					     u16 addr, u8 byte_cnt, u8 *o_buf)
{
	struct bnx2x *bp = params->bp;
	u16 val, i;

	if (byte_cnt > 16) {
		DP(NETIF_MSG_LINK, "Reading from eeprom is"
			    " is limited to 0xf\n");
		return -EINVAL;
	}

	/* Need to read from 1.8000 to clear it */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
			&val);

	/* Set the read command byte count */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
			 ((byte_cnt < 2) ? 2 : byte_cnt));

	/* Set the read command address */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR,
			 addr);
	/* Set the destination address */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 0x8004,
			 MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF);

	/* Activate read command */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL,
			 0x8002);
	/*
	 * Wait appropriate time for two-wire command to finish before
	 * polling the status register
	 */
	msleep(1);

	/* Wait up to 500us for command complete status */
	for (i = 0; i < 100; i++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
		if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
		    MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE)
			break;
		udelay(5);
	}

	if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) !=
		    MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) {
		DP(NETIF_MSG_LINK,
			 "Got bad status 0x%x when reading from SFP+ EEPROM\n",
			 (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK));
		return -EFAULT;
	}

	/* Read the buffer */
	for (i = 0; i < byte_cnt; i++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val);
		o_buf[i] = (u8)(val & MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK);
	}

	for (i = 0; i < 100; i++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val);
		if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) ==
		    MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE)
			return 0;
		msleep(1);
	}

	return -EINVAL;
}

int bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy,
				 struct link_params *params, u16 addr,
				 u8 byte_cnt, u8 *o_buf)
{
	int rc = -EINVAL;
	switch (phy->type) {
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
		rc = bnx2x_8726_read_sfp_module_eeprom(phy, params, addr,
						       byte_cnt, o_buf);
	break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
		rc = bnx2x_8727_read_sfp_module_eeprom(phy, params, addr,
						       byte_cnt, o_buf);
	break;
	}
	return rc;
}

static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
			      struct link_params *params,
			      u16 *edc_mode)
{
	struct bnx2x *bp = params->bp;
	u32 sync_offset = 0, phy_idx, media_types;
	u8 val, check_limiting_mode = 0;
	*edc_mode = EDC_MODE_LIMITING;

	phy->media_type = ETH_PHY_UNSPECIFIED;
	/* First check for copper cable */
	if (bnx2x_read_sfp_module_eeprom(phy,
					 params,
					 SFP_EEPROM_CON_TYPE_ADDR,
					 1,
					 &val) != 0) {
		DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n");
		return -EINVAL;
	}

	switch (val) {
	case SFP_EEPROM_CON_TYPE_VAL_COPPER:
	{
		u8 copper_module_type;
		phy->media_type = ETH_PHY_DA_TWINAX;
		/*
		 * Check if its active cable (includes SFP+ module)
		 * of passive cable
		 */
		if (bnx2x_read_sfp_module_eeprom(phy,
					       params,
					       SFP_EEPROM_FC_TX_TECH_ADDR,
					       1,
					       &copper_module_type) !=
		    0) {
			DP(NETIF_MSG_LINK,
				"Failed to read copper-cable-type"
				" from SFP+ EEPROM\n");
			return -EINVAL;
		}

		if (copper_module_type &
		    SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) {
			DP(NETIF_MSG_LINK, "Active Copper cable detected\n");
			check_limiting_mode = 1;
		} else if (copper_module_type &
			SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) {
				DP(NETIF_MSG_LINK, "Passive Copper"
					    " cable detected\n");
				*edc_mode =
				      EDC_MODE_PASSIVE_DAC;
		} else {
			DP(NETIF_MSG_LINK, "Unknown copper-cable-"
				     "type 0x%x !!!\n", copper_module_type);
			return -EINVAL;
		}
		break;
	}
	case SFP_EEPROM_CON_TYPE_VAL_LC:
		phy->media_type = ETH_PHY_SFP_FIBER;
		DP(NETIF_MSG_LINK, "Optic module detected\n");
		check_limiting_mode = 1;
		break;
	default:
		DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n",
			 val);
		return -EINVAL;
	}
	sync_offset = params->shmem_base +
		offsetof(struct shmem_region,
			 dev_info.port_hw_config[params->port].media_type);
	media_types = REG_RD(bp, sync_offset);
	/* Update media type for non-PMF sync */
	for (phy_idx = INT_PHY; phy_idx < MAX_PHYS; phy_idx++) {
		if (&(params->phy[phy_idx]) == phy) {
			media_types &= ~(PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK <<
				(PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx));
			media_types |= ((phy->media_type &
					PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) <<
				(PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx));
			break;
		}
	}
	REG_WR(bp, sync_offset, media_types);
	if (check_limiting_mode) {
		u8 options[SFP_EEPROM_OPTIONS_SIZE];
		if (bnx2x_read_sfp_module_eeprom(phy,
						 params,
						 SFP_EEPROM_OPTIONS_ADDR,
						 SFP_EEPROM_OPTIONS_SIZE,
						 options) != 0) {
			DP(NETIF_MSG_LINK, "Failed to read Option"
				" field from module EEPROM\n");
			return -EINVAL;
		}
		if ((options[0] & SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK))
			*edc_mode = EDC_MODE_LINEAR;
		else
			*edc_mode = EDC_MODE_LIMITING;
	}
	DP(NETIF_MSG_LINK, "EDC mode is set to 0x%x\n", *edc_mode);
	return 0;
}
/*
 * This function read the relevant field from the module (SFP+), and verify it
 * is compliant with this board
 */
static int bnx2x_verify_sfp_module(struct bnx2x_phy *phy,
				   struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u32 val, cmd;
	u32 fw_resp, fw_cmd_param;
	char vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE+1];
	char vendor_pn[SFP_EEPROM_PART_NO_SIZE+1];
	phy->flags &= ~FLAGS_SFP_NOT_APPROVED;
	val = REG_RD(bp, params->shmem_base +
			 offsetof(struct shmem_region, dev_info.
				  port_feature_config[params->port].config));
	if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
	    PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_NO_ENFORCEMENT) {
		DP(NETIF_MSG_LINK, "NOT enforcing module verification\n");
		return 0;
	}

	if (params->feature_config_flags &
	    FEATURE_CONFIG_BC_SUPPORTS_DUAL_PHY_OPT_MDL_VRFY) {
		/* Use specific phy request */
		cmd = DRV_MSG_CODE_VRFY_SPECIFIC_PHY_OPT_MDL;
	} else if (params->feature_config_flags &
		   FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY) {
		/* Use first phy request only in case of non-dual media*/
		if (DUAL_MEDIA(params)) {
			DP(NETIF_MSG_LINK, "FW does not support OPT MDL "
			   "verification\n");
			return -EINVAL;
		}
		cmd = DRV_MSG_CODE_VRFY_FIRST_PHY_OPT_MDL;
	} else {
		/* No support in OPT MDL detection */
		DP(NETIF_MSG_LINK, "FW does not support OPT MDL "
			  "verification\n");
		return -EINVAL;
	}

	fw_cmd_param = FW_PARAM_SET(phy->addr, phy->type, phy->mdio_ctrl);
	fw_resp = bnx2x_fw_command(bp, cmd, fw_cmd_param);
	if (fw_resp == FW_MSG_CODE_VRFY_OPT_MDL_SUCCESS) {
		DP(NETIF_MSG_LINK, "Approved module\n");
		return 0;
	}

	/* format the warning message */
	if (bnx2x_read_sfp_module_eeprom(phy,
					 params,
					 SFP_EEPROM_VENDOR_NAME_ADDR,
					 SFP_EEPROM_VENDOR_NAME_SIZE,
					 (u8 *)vendor_name))
		vendor_name[0] = '\0';
	else
		vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0';
	if (bnx2x_read_sfp_module_eeprom(phy,
					 params,
					 SFP_EEPROM_PART_NO_ADDR,
					 SFP_EEPROM_PART_NO_SIZE,
					 (u8 *)vendor_pn))
		vendor_pn[0] = '\0';
	else
		vendor_pn[SFP_EEPROM_PART_NO_SIZE] = '\0';

	netdev_err(bp->dev,  "Warning: Unqualified SFP+ module detected,"
			      " Port %d from %s part number %s\n",
			 params->port, vendor_name, vendor_pn);
	phy->flags |= FLAGS_SFP_NOT_APPROVED;
	return -EINVAL;
}

static int bnx2x_wait_for_sfp_module_initialized(struct bnx2x_phy *phy,
						 struct link_params *params)

{
	u8 val;
	struct bnx2x *bp = params->bp;
	u16 timeout;
	/*
	 * Initialization time after hot-plug may take up to 300ms for
	 * some phys type ( e.g. JDSU )
	 */

	for (timeout = 0; timeout < 60; timeout++) {
		if (bnx2x_read_sfp_module_eeprom(phy, params, 1, 1, &val)
		    == 0) {
			DP(NETIF_MSG_LINK, "SFP+ module initialization "
				     "took %d ms\n", timeout * 5);
			return 0;
		}
		msleep(5);
	}
	return -EINVAL;
}

static void bnx2x_8727_power_module(struct bnx2x *bp,
				    struct bnx2x_phy *phy,
				    u8 is_power_up) {
	/* Make sure GPIOs are not using for LED mode */
	u16 val;
	/*
	 * In the GPIO register, bit 4 is use to determine if the GPIOs are
	 * operating as INPUT or as OUTPUT. Bit 1 is for input, and 0 for
	 * output
	 * Bits 0-1 determine the gpios value for OUTPUT in case bit 4 val is 0
	 * Bits 8-9 determine the gpios value for INPUT in case bit 4 val is 1
	 * where the 1st bit is the over-current(only input), and 2nd bit is
	 * for power( only output )
	 *
	 * In case of NOC feature is disabled and power is up, set GPIO control
	 *  as input to enable listening of over-current indication
	 */
	if (phy->flags & FLAGS_NOC)
		return;
	if (!(phy->flags &
	      FLAGS_NOC) && is_power_up)
		val = (1<<4);
	else
		/*
		 * Set GPIO control to OUTPUT, and set the power bit
		 * to according to the is_power_up
		 */
		val = ((!(is_power_up)) << 1);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_8727_GPIO_CTRL,
			 val);
}

static int bnx2x_8726_set_limiting_mode(struct bnx2x *bp,
					struct bnx2x_phy *phy,
					u16 edc_mode)
{
	u16 cur_limiting_mode;

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_ROM_VER2,
			&cur_limiting_mode);
	DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n",
		 cur_limiting_mode);

	if (edc_mode == EDC_MODE_LIMITING) {
		DP(NETIF_MSG_LINK, "Setting LIMITING MODE\n");
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_ROM_VER2,
				 EDC_MODE_LIMITING);
	} else { /* LRM mode ( default )*/

		DP(NETIF_MSG_LINK, "Setting LRM MODE\n");

		/*
		 * Changing to LRM mode takes quite few seconds. So do it only
		 * if current mode is limiting (default is LRM)
		 */
		if (cur_limiting_mode != EDC_MODE_LIMITING)
			return 0;

		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_LRM_MODE,
				 0);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_ROM_VER2,
				 0x128);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_MISC_CTRL0,
				 0x4008);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_LRM_MODE,
				 0xaaaa);
	}
	return 0;
}

static int bnx2x_8727_set_limiting_mode(struct bnx2x *bp,
					struct bnx2x_phy *phy,
					u16 edc_mode)
{
	u16 phy_identifier;
	u16 rom_ver2_val;
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_PHY_IDENTIFIER,
			&phy_identifier);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_PHY_IDENTIFIER,
			 (phy_identifier & ~(1<<9)));

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_ROM_VER2,
			&rom_ver2_val);
	/* Keep the MSB 8-bits, and set the LSB 8-bits with the edc_mode */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_ROM_VER2,
			 (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff));

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_PHY_IDENTIFIER,
			 (phy_identifier | (1<<9)));

	return 0;
}

static void bnx2x_8727_specific_func(struct bnx2x_phy *phy,
				     struct link_params *params,
				     u32 action)
{
	struct bnx2x *bp = params->bp;

	switch (action) {
	case DISABLE_TX:
		bnx2x_sfp_set_transmitter(params, phy, 0);
		break;
	case ENABLE_TX:
		if (!(phy->flags & FLAGS_SFP_NOT_APPROVED))
			bnx2x_sfp_set_transmitter(params, phy, 1);
		break;
	default:
		DP(NETIF_MSG_LINK, "Function 0x%x not supported by 8727\n",
		   action);
		return;
	}
}

static void bnx2x_set_sfp_module_fault_led(struct link_params *params,
					   u8 gpio_mode)
{
	struct bnx2x *bp = params->bp;

	u32 fault_led_gpio = REG_RD(bp, params->shmem_base +
			    offsetof(struct shmem_region,
			dev_info.port_hw_config[params->port].sfp_ctrl)) &
		PORT_HW_CFG_FAULT_MODULE_LED_MASK;
	switch (fault_led_gpio) {
	case PORT_HW_CFG_FAULT_MODULE_LED_DISABLED:
		return;
	case PORT_HW_CFG_FAULT_MODULE_LED_GPIO0:
	case PORT_HW_CFG_FAULT_MODULE_LED_GPIO1:
	case PORT_HW_CFG_FAULT_MODULE_LED_GPIO2:
	case PORT_HW_CFG_FAULT_MODULE_LED_GPIO3:
	{
		u8 gpio_port = bnx2x_get_gpio_port(params);
		u16 gpio_pin = fault_led_gpio -
			PORT_HW_CFG_FAULT_MODULE_LED_GPIO0;
		DP(NETIF_MSG_LINK, "Set fault module-detected led "
				   "pin %x port %x mode %x\n",
			       gpio_pin, gpio_port, gpio_mode);
		bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port);
	}
	break;
	default:
		DP(NETIF_MSG_LINK, "Error: Invalid fault led mode 0x%x\n",
			       fault_led_gpio);
	}
}

static void bnx2x_power_sfp_module(struct link_params *params,
				   struct bnx2x_phy *phy,
				   u8 power)
{
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "Setting SFP+ power to %x\n", power);

	switch (phy->type) {
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
		bnx2x_8727_power_module(params->bp, phy, power);
		break;
	default:
		break;
	}
}

static void bnx2x_set_limiting_mode(struct link_params *params,
				    struct bnx2x_phy *phy,
				    u16 edc_mode)
{
	switch (phy->type) {
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
		bnx2x_8726_set_limiting_mode(params->bp, phy, edc_mode);
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
		bnx2x_8727_set_limiting_mode(params->bp, phy, edc_mode);
		break;
	}
}

int bnx2x_sfp_module_detection(struct bnx2x_phy *phy,
			       struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u16 edc_mode;
	int rc = 0;

	u32 val = REG_RD(bp, params->shmem_base +
			     offsetof(struct shmem_region, dev_info.
				     port_feature_config[params->port].config));

	DP(NETIF_MSG_LINK, "SFP+ module plugged in/out detected on port %d\n",
		 params->port);
	/* Power up module */
	bnx2x_power_sfp_module(params, phy, 1);
	if (bnx2x_get_edc_mode(phy, params, &edc_mode) != 0) {
		DP(NETIF_MSG_LINK, "Failed to get valid module type\n");
		return -EINVAL;
	} else if (bnx2x_verify_sfp_module(phy, params) != 0) {
		/* check SFP+ module compatibility */
		DP(NETIF_MSG_LINK, "Module verification failed!!\n");
		rc = -EINVAL;
		/* Turn on fault module-detected led */
		bnx2x_set_sfp_module_fault_led(params,
					       MISC_REGISTERS_GPIO_HIGH);

		/* Check if need to power down the SFP+ module */
		if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
		     PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN) {
			DP(NETIF_MSG_LINK, "Shutdown SFP+ module!!\n");
			bnx2x_power_sfp_module(params, phy, 0);
			return rc;
		}
	} else {
		/* Turn off fault module-detected led */
		bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_LOW);
	}

	/*
	 * Check and set limiting mode / LRM mode on 8726. On 8727 it
	 * is done automatically
	 */
	bnx2x_set_limiting_mode(params, phy, edc_mode);

	/*
	 * Enable transmit for this module if the module is approved, or
	 * if unapproved modules should also enable the Tx laser
	 */
	if (rc == 0 ||
	    (val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) !=
	    PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
		bnx2x_sfp_set_transmitter(params, phy, 1);
	else
		bnx2x_sfp_set_transmitter(params, phy, 0);

	return rc;
}

void bnx2x_handle_module_detect_int(struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	struct bnx2x_phy *phy = &params->phy[EXT_PHY1];
	u32 gpio_val;
	u8 port = params->port;

	/* Set valid module led off */
	bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_HIGH);

	/* Get current gpio val reflecting module plugged in / out*/
	gpio_val = bnx2x_get_gpio(bp, MISC_REGISTERS_GPIO_3, port);

	/* Call the handling function in case module is detected */
	if (gpio_val == 0) {
		bnx2x_power_sfp_module(params, phy, 1);
		bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3,
				   MISC_REGISTERS_GPIO_INT_OUTPUT_CLR,
				   port);

		if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0)
			bnx2x_sfp_module_detection(phy, params);
		else
			DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
	} else {
		u32 val = REG_RD(bp, params->shmem_base +
				 offsetof(struct shmem_region, dev_info.
					  port_feature_config[params->port].
					  config));

		bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3,
				   MISC_REGISTERS_GPIO_INT_OUTPUT_SET,
				   port);
		/*
		 * Module was plugged out.
		 * Disable transmit for this module
		 */
		phy->media_type = ETH_PHY_NOT_PRESENT;
		if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
		    PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
			bnx2x_sfp_set_transmitter(params, phy, 0);
	}
}

/******************************************************************/
/*		common BCM8706/BCM8726 PHY SECTION		  */
/******************************************************************/
static u8 bnx2x_8706_8726_read_status(struct bnx2x_phy *phy,
				      struct link_params *params,
				      struct link_vars *vars)
{
	u8 link_up = 0;
	u16 val1, val2, rx_sd, pcs_status;
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "XGXS 8706/8726\n");
	/* Clear RX Alarm*/
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM, &val2);
	/* clear LASI indication*/
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val1);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val2);
	DP(NETIF_MSG_LINK, "8706/8726 LASI status 0x%x--> 0x%x\n", val1, val2);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD, &rx_sd);
	bnx2x_cl45_read(bp, phy,
			MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &pcs_status);
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &val2);
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &val2);

	DP(NETIF_MSG_LINK, "8706/8726 rx_sd 0x%x pcs_status 0x%x 1Gbps"
			" link_status 0x%x\n", rx_sd, pcs_status, val2);
	/*
	 * link is up if both bit 0 of pmd_rx_sd and bit 0 of pcs_status
	 * are set, or if the autoneg bit 1 is set
	 */
	link_up = ((rx_sd & pcs_status & 0x1) || (val2 & (1<<1)));
	if (link_up) {
		if (val2 & (1<<1))
			vars->line_speed = SPEED_1000;
		else
			vars->line_speed = SPEED_10000;
		bnx2x_ext_phy_resolve_fc(phy, params, vars);
		vars->duplex = DUPLEX_FULL;
	}
	return link_up;
}

/******************************************************************/
/*			BCM8706 PHY SECTION			  */
/******************************************************************/
static u8 bnx2x_8706_config_init(struct bnx2x_phy *phy,
				 struct link_params *params,
				 struct link_vars *vars)
{
	u32 tx_en_mode;
	u16 cnt, val, tmp1;
	struct bnx2x *bp = params->bp;
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
	/* HW reset */
	bnx2x_ext_phy_hw_reset(bp, params->port);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040);
	bnx2x_wait_reset_complete(bp, phy, params);

	/* Wait until fw is loaded */
	for (cnt = 0; cnt < 100; cnt++) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD, MDIO_PMA_REG_ROM_VER1, &val);
		if (val)
			break;
		msleep(10);
	}
	DP(NETIF_MSG_LINK, "XGXS 8706 is initialized after %d ms\n", cnt);
	if ((params->feature_config_flags &
	     FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
		u8 i;
		u16 reg;
		for (i = 0; i < 4; i++) {
			reg = MDIO_XS_8706_REG_BANK_RX0 +
				i*(MDIO_XS_8706_REG_BANK_RX1 -
				   MDIO_XS_8706_REG_BANK_RX0);
			bnx2x_cl45_read(bp, phy, MDIO_XS_DEVAD, reg, &val);
			/* Clear first 3 bits of the control */
			val &= ~0x7;
			/* Set control bits according to configuration */
			val |= (phy->rx_preemphasis[i] & 0x7);
			DP(NETIF_MSG_LINK, "Setting RX Equalizer to BCM8706"
				   " reg 0x%x <-- val 0x%x\n", reg, val);
			bnx2x_cl45_write(bp, phy, MDIO_XS_DEVAD, reg, val);
		}
	}
	/* Force speed */
	if (phy->req_line_speed == SPEED_10000) {
		DP(NETIF_MSG_LINK, "XGXS 8706 force 10Gbps\n");

		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_DIGITAL_CTRL, 0x400);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 1);
	} else {
		/* Force 1Gbps using autoneg with 1G advertisement */

		/* Allow CL37 through CL73 */
		DP(NETIF_MSG_LINK, "XGXS 8706 AutoNeg\n");
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_CL73, 0x040c);

		/* Enable Full-Duplex advertisement on CL37 */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LP, 0x0020);
		/* Enable CL37 AN */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000);
		/* 1G support */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_ADV, (1<<5));

		/* Enable clause 73 AN */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM_CTRL,
				 0x0400);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL,
				 0x0004);
	}
	bnx2x_save_bcm_spirom_ver(bp, phy, params->port);

	/*
	 * If TX Laser is controlled by GPIO_0, do not let PHY go into low
	 * power mode, if TX Laser is disabled
	 */

	tx_en_mode = REG_RD(bp, params->shmem_base +
			    offsetof(struct shmem_region,
				dev_info.port_hw_config[params->port].sfp_ctrl))
			& PORT_HW_CFG_TX_LASER_MASK;

	if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) {
		DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n");
		bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, &tmp1);
		tmp1 |= 0x1;
		bnx2x_cl45_write(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, tmp1);
	}

	return 0;
}

static int bnx2x_8706_read_status(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	return bnx2x_8706_8726_read_status(phy, params, vars);
}

/******************************************************************/
/*			BCM8726 PHY SECTION			  */
/******************************************************************/
static void bnx2x_8726_config_loopback(struct bnx2x_phy *phy,
				       struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "PMA/PMD ext_phy_loopback: 8726\n");
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x0001);
}

static void bnx2x_8726_external_rom_boot(struct bnx2x_phy *phy,
					 struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	/* Need to wait 100ms after reset */
	msleep(100);

	/* Micro controller re-boot */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x018B);

	/* Set soft reset */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_GEN_CTRL,
			 MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_MISC_CTRL1, 0x0001);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_GEN_CTRL,
			 MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);

	/* wait for 150ms for microcode load */
	msleep(150);

	/* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_MISC_CTRL1, 0x0000);

	msleep(200);
	bnx2x_save_bcm_spirom_ver(bp, phy, params->port);
}

static u8 bnx2x_8726_read_status(struct bnx2x_phy *phy,
				 struct link_params *params,
				 struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 val1;
	u8 link_up = bnx2x_8706_8726_read_status(phy, params, vars);
	if (link_up) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER,
				&val1);
		if (val1 & (1<<15)) {
			DP(NETIF_MSG_LINK, "Tx is disabled\n");
			link_up = 0;
			vars->line_speed = 0;
		}
	}
	return link_up;
}


static int bnx2x_8726_config_init(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u32 val;
	u32 swap_val, swap_override, aeu_gpio_mask, offset;
	DP(NETIF_MSG_LINK, "Initializing BCM8726\n");

	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
	bnx2x_wait_reset_complete(bp, phy, params);

	bnx2x_8726_external_rom_boot(phy, params);

	/*
	 * Need to call module detected on initialization since the module
	 * detection triggered by actual module insertion might occur before
	 * driver is loaded, and when driver is loaded, it reset all
	 * registers, including the transmitter
	 */
	bnx2x_sfp_module_detection(phy, params);

	if (phy->req_line_speed == SPEED_1000) {
		DP(NETIF_MSG_LINK, "Setting 1G force\n");
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 0x5);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM_CTRL,
				 0x400);
	} else if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
		   (phy->speed_cap_mask &
		      PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) &&
		   ((phy->speed_cap_mask &
		      PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) !=
		    PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
		DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
		/* Set Flow control */
		bnx2x_ext_phy_set_pause(params, phy, vars);
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_ADV, 0x20);
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_CL73, 0x040c);
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, 0x0020);
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000);
		bnx2x_cl45_write(bp, phy,
				MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200);
		/*
		 * Enable RX-ALARM control to receive interrupt for 1G speed
		 * change
		 */
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 0x4);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM_CTRL,
				 0x400);

	} else { /* Default 10G. Set only LASI control */
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 1);
	}

	/* Set TX PreEmphasis if needed */
	if ((params->feature_config_flags &
	     FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
		DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x,"
			 "TX_CTRL2 0x%x\n",
			 phy->tx_preemphasis[0],
			 phy->tx_preemphasis[1]);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_8726_TX_CTRL1,
				 phy->tx_preemphasis[0]);

		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_8726_TX_CTRL2,
				 phy->tx_preemphasis[1]);
	}

	/* Set GPIO3 to trigger SFP+ module insertion/removal */
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
		       MISC_REGISTERS_GPIO_INPUT_HI_Z, params->port);

	/* The GPIO should be swapped if the swap register is set and active */
	swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
	swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);

	/* Select function upon port-swap configuration */
	if (params->port == 0) {
		offset = MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0;
		aeu_gpio_mask = (swap_val && swap_override) ?
			AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1 :
			AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0;
	} else {
		offset = MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0;
		aeu_gpio_mask = (swap_val && swap_override) ?
			AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 :
			AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1;
	}
	val = REG_RD(bp, offset);
	/* add GPIO3 to group */
	val |= aeu_gpio_mask;
	REG_WR(bp, offset, val);
	return 0;

}

static void bnx2x_8726_link_reset(struct bnx2x_phy *phy,
				  struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "bnx2x_8726_link_reset port %d\n", params->port);
	/* Set serial boot control for external load */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_GEN_CTRL, 0x0001);
}

/******************************************************************/
/*			BCM8727 PHY SECTION			  */
/******************************************************************/

static void bnx2x_8727_set_link_led(struct bnx2x_phy *phy,
				    struct link_params *params, u8 mode)
{
	struct bnx2x *bp = params->bp;
	u16 led_mode_bitmask = 0;
	u16 gpio_pins_bitmask = 0;
	u16 val;
	/* Only NOC flavor requires to set the LED specifically */
	if (!(phy->flags & FLAGS_NOC))
		return;
	switch (mode) {
	case LED_MODE_FRONT_PANEL_OFF:
	case LED_MODE_OFF:
		led_mode_bitmask = 0;
		gpio_pins_bitmask = 0x03;
		break;
	case LED_MODE_ON:
		led_mode_bitmask = 0;
		gpio_pins_bitmask = 0x02;
		break;
	case LED_MODE_OPER:
		led_mode_bitmask = 0x60;
		gpio_pins_bitmask = 0x11;
		break;
	}
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_8727_PCS_OPT_CTRL,
			&val);
	val &= 0xff8f;
	val |= led_mode_bitmask;
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_8727_PCS_OPT_CTRL,
			 val);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_8727_GPIO_CTRL,
			&val);
	val &= 0xffe0;
	val |= gpio_pins_bitmask;
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_8727_GPIO_CTRL,
			 val);
}
static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy,
				struct link_params *params) {
	u32 swap_val, swap_override;
	u8 port;
	/*
	 * The PHY reset is controlled by GPIO 1. Fake the port number
	 * to cancel the swap done in set_gpio()
	 */
	struct bnx2x *bp = params->bp;
	swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
	swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
	port = (swap_val && swap_override) ^ 1;
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
}

static int bnx2x_8727_config_init(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	u32 tx_en_mode;
	u16 tmp1, val, mod_abs, tmp2;
	u16 rx_alarm_ctrl_val;
	u16 lasi_ctrl_val;
	struct bnx2x *bp = params->bp;
	/* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */

	bnx2x_wait_reset_complete(bp, phy, params);
	rx_alarm_ctrl_val = (1<<2) | (1<<5) ;
	lasi_ctrl_val = 0x0004;

	DP(NETIF_MSG_LINK, "Initializing BCM8727\n");
	/* enable LASI */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM_CTRL,
			 rx_alarm_ctrl_val);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, lasi_ctrl_val);

	/*
	 * Initially configure MOD_ABS to interrupt when module is
	 * presence( bit 8)
	 */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
	/*
	 * Set EDC off by setting OPTXLOS signal input to low (bit 9).
	 * When the EDC is off it locks onto a reference clock and avoids
	 * becoming 'lost'
	 */
	mod_abs &= ~(1<<8);
	if (!(phy->flags & FLAGS_NOC))
		mod_abs &= ~(1<<9);
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);


	/* Make MOD_ABS give interrupt on change */
	bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_PCS_OPT_CTRL,
			&val);
	val |= (1<<12);
	if (phy->flags & FLAGS_NOC)
		val |= (3<<5);

	/*
	 * Set 8727 GPIOs to input to allow reading from the 8727 GPIO0
	 * status which reflect SFP+ module over-current
	 */
	if (!(phy->flags & FLAGS_NOC))
		val &= 0xff8f; /* Reset bits 4-6 */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_PCS_OPT_CTRL, val);

	bnx2x_8727_power_module(bp, phy, 1);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &tmp1);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM, &tmp1);

	/* Set option 1G speed */
	if (phy->req_line_speed == SPEED_1000) {
		DP(NETIF_MSG_LINK, "Setting 1G force\n");
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD);
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1);
		DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1);
		/*
		 * Power down the XAUI until link is up in case of dual-media
		 * and 1G
		 */
		if (DUAL_MEDIA(params)) {
			bnx2x_cl45_read(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8727_PCS_GP, &val);
			val |= (3<<10);
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8727_PCS_GP, val);
		}
	} else if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
		   ((phy->speed_cap_mask &
		     PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) &&
		   ((phy->speed_cap_mask &
		      PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) !=
		   PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {

		DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 0);
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300);
	} else {
		/*
		 * Since the 8727 has only single reset pin, need to set the 10G
		 * registers although it is default
		 */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL,
				 0x0020);
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x0100);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2,
				 0x0008);
	}

	/*
	 * Set 2-wire transfer rate of SFP+ module EEPROM
	 * to 100Khz since some DACs(direct attached cables) do
	 * not work at 400Khz.
	 */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR,
			 0xa001);

	/* Set TX PreEmphasis if needed */
	if ((params->feature_config_flags &
	     FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
		DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x, TX_CTRL2 0x%x\n",
			   phy->tx_preemphasis[0],
			   phy->tx_preemphasis[1]);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TX_CTRL1,
				 phy->tx_preemphasis[0]);

		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TX_CTRL2,
				 phy->tx_preemphasis[1]);
	}

	/*
	 * If TX Laser is controlled by GPIO_0, do not let PHY go into low
	 * power mode, if TX Laser is disabled
	 */
	tx_en_mode = REG_RD(bp, params->shmem_base +
			    offsetof(struct shmem_region,
				dev_info.port_hw_config[params->port].sfp_ctrl))
			& PORT_HW_CFG_TX_LASER_MASK;

	if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) {

		DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n");
		bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, &tmp2);
		tmp2 |= 0x1000;
		tmp2 &= 0xFFEF;
		bnx2x_cl45_write(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, tmp2);
	}

	return 0;
}

static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy,
				      struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u16 mod_abs, rx_alarm_status;
	u32 val = REG_RD(bp, params->shmem_base +
			     offsetof(struct shmem_region, dev_info.
				      port_feature_config[params->port].
				      config));
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs);
	if (mod_abs & (1<<8)) {

		/* Module is absent */
		DP(NETIF_MSG_LINK, "MOD_ABS indication "
			    "show module is absent\n");
		phy->media_type = ETH_PHY_NOT_PRESENT;
		/*
		 * 1. Set mod_abs to detect next module
		 *    presence event
		 * 2. Set EDC off by setting OPTXLOS signal input to low
		 *    (bit 9).
		 *    When the EDC is off it locks onto a reference clock and
		 *    avoids becoming 'lost'.
		 */
		mod_abs &= ~(1<<8);
		if (!(phy->flags & FLAGS_NOC))
			mod_abs &= ~(1<<9);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);

		/*
		 * Clear RX alarm since it stays up as long as
		 * the mod_abs wasn't changed
		 */
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);

	} else {
		/* Module is present */
		DP(NETIF_MSG_LINK, "MOD_ABS indication "
			    "show module is present\n");
		/*
		 * First disable transmitter, and if the module is ok, the
		 * module_detection will enable it
		 * 1. Set mod_abs to detect next module absent event ( bit 8)
		 * 2. Restore the default polarity of the OPRXLOS signal and
		 * this signal will then correctly indicate the presence or
		 * absence of the Rx signal. (bit 9)
		 */
		mod_abs |= (1<<8);
		if (!(phy->flags & FLAGS_NOC))
			mod_abs |= (1<<9);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs);

		/*
		 * Clear RX alarm since it stays up as long as the mod_abs
		 * wasn't changed. This is need to be done before calling the
		 * module detection, otherwise it will clear* the link update
		 * alarm
		 */
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);


		if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
		    PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
			bnx2x_sfp_set_transmitter(params, phy, 0);

		if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0)
			bnx2x_sfp_module_detection(phy, params);
		else
			DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
	}

	DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n",
		   rx_alarm_status);
	/* No need to check link status in case of module plugged in/out */
}

static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy,
				 struct link_params *params,
				 struct link_vars *vars)

{
	struct bnx2x *bp = params->bp;
	u8 link_up = 0;
	u16 link_status = 0;
	u16 rx_alarm_status, lasi_ctrl, val1;

	/* If PHY is not initialized, do not check link status */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL,
			&lasi_ctrl);
	if (!lasi_ctrl)
		return 0;

	/* Check the LASI */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM,
			&rx_alarm_status);
	vars->line_speed = 0;
	DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS  0x%x\n", rx_alarm_status);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val1);

	DP(NETIF_MSG_LINK, "8727 LASI status 0x%x\n", val1);

	/* Clear MSG-OUT */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &val1);

	/*
	 * If a module is present and there is need to check
	 * for over current
	 */
	if (!(phy->flags & FLAGS_NOC) && !(rx_alarm_status & (1<<5))) {
		/* Check over-current using 8727 GPIO0 input*/
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_GPIO_CTRL,
				&val1);

		if ((val1 & (1<<8)) == 0) {
			DP(NETIF_MSG_LINK, "8727 Power fault has been detected"
				       " on port %d\n", params->port);
			netdev_err(bp->dev, "Error:  Power fault on Port %d has"
					    " been detected and the power to "
					    "that SFP+ module has been removed"
					    " to prevent failure of the card."
					    " Please remove the SFP+ module and"
					    " restart the system to clear this"
					    " error.\n",
			 params->port);
			/* Disable all RX_ALARMs except for mod_abs */
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_RX_ALARM_CTRL, (1<<5));

			bnx2x_cl45_read(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_PHY_IDENTIFIER, &val1);
			/* Wait for module_absent_event */
			val1 |= (1<<8);
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_PHY_IDENTIFIER, val1);
			/* Clear RX alarm */
			bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_RX_ALARM, &rx_alarm_status);
			return 0;
		}
	} /* Over current check */

	/* When module absent bit is set, check module */
	if (rx_alarm_status & (1<<5)) {
		bnx2x_8727_handle_mod_abs(phy, params);
		/* Enable all mod_abs and link detection bits */
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM_CTRL,
				 ((1<<5) | (1<<2)));
	}
	DP(NETIF_MSG_LINK, "Enabling 8727 TX laser if SFP is approved\n");
	bnx2x_8727_specific_func(phy, params, ENABLE_TX);
	/* If transmitter is disabled, ignore false link up indication */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, &val1);
	if (val1 & (1<<15)) {
		DP(NETIF_MSG_LINK, "Tx is disabled\n");
		return 0;
	}

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_8073_SPEED_LINK_STATUS, &link_status);

	/*
	 * Bits 0..2 --> speed detected,
	 * Bits 13..15--> link is down
	 */
	if ((link_status & (1<<2)) && (!(link_status & (1<<15)))) {
		link_up = 1;
		vars->line_speed = SPEED_10000;
		DP(NETIF_MSG_LINK, "port %x: External link up in 10G\n",
			   params->port);
	} else if ((link_status & (1<<0)) && (!(link_status & (1<<13)))) {
		link_up = 1;
		vars->line_speed = SPEED_1000;
		DP(NETIF_MSG_LINK, "port %x: External link up in 1G\n",
			   params->port);
	} else {
		link_up = 0;
		DP(NETIF_MSG_LINK, "port %x: External link is down\n",
			   params->port);
	}
	if (link_up) {
		bnx2x_ext_phy_resolve_fc(phy, params, vars);
		vars->duplex = DUPLEX_FULL;
		DP(NETIF_MSG_LINK, "duplex = 0x%x\n", vars->duplex);
	}

	if ((DUAL_MEDIA(params)) &&
	    (phy->req_line_speed == SPEED_1000)) {
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_8727_PCS_GP, &val1);
		/*
		 * In case of dual-media board and 1G, power up the XAUI side,
		 * otherwise power it down. For 10G it is done automatically
		 */
		if (link_up)
			val1 &= ~(3<<10);
		else
			val1 |= (3<<10);
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_8727_PCS_GP, val1);
	}
	return link_up;
}

static void bnx2x_8727_link_reset(struct bnx2x_phy *phy,
				  struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	/* Disable Transmitter */
	bnx2x_sfp_set_transmitter(params, phy, 0);
	/* Clear LASI */
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 0);

}

/******************************************************************/
/*		BCM8481/BCM84823/BCM84833 PHY SECTION	          */
/******************************************************************/
static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy,
					   struct link_params *params)
{
	u16 val, fw_ver1, fw_ver2, cnt, adj;
	struct bnx2x *bp = params->bp;

	adj = 0;
	if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
		adj = -1;

	/* For the 32 bits registers in 848xx, access via MDIO2ARM interface.*/
	/* (1) set register 0xc200_0014(SPI_BRIDGE_CTRL_2) to 0x03000000 */
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819 + adj, 0x0014);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A + adj, 0xc200);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81B + adj, 0x0000);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81C + adj, 0x0300);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817 + adj, 0x0009);

	for (cnt = 0; cnt < 100; cnt++) {
		bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818 + adj, &val);
		if (val & 1)
			break;
		udelay(5);
	}
	if (cnt == 100) {
		DP(NETIF_MSG_LINK, "Unable to read 848xx phy fw version(1)\n");
		bnx2x_save_spirom_version(bp, params->port, 0,
					  phy->ver_addr);
		return;
	}


	/* 2) read register 0xc200_0000 (SPI_FW_STATUS) */
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819 + adj, 0x0000);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A + adj, 0xc200);
	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817 + adj, 0x000A);
	for (cnt = 0; cnt < 100; cnt++) {
		bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818 + adj, &val);
		if (val & 1)
			break;
		udelay(5);
	}
	if (cnt == 100) {
		DP(NETIF_MSG_LINK, "Unable to read 848xx phy fw version(2)\n");
		bnx2x_save_spirom_version(bp, params->port, 0,
					  phy->ver_addr);
		return;
	}

	/* lower 16 bits of the register SPI_FW_STATUS */
	bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81B + adj, &fw_ver1);
	/* upper 16 bits of register SPI_FW_STATUS */
	bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81C + adj, &fw_ver2);

	bnx2x_save_spirom_version(bp, params->port, (fw_ver2<<16) | fw_ver1,
				  phy->ver_addr);
}

static void bnx2x_848xx_set_led(struct bnx2x *bp,
				struct bnx2x_phy *phy)
{
	u16 val, adj;

	adj = 0;
	if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
		adj = -1;

	/* PHYC_CTL_LED_CTL */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_8481_LINK_SIGNAL + adj, &val);
	val &= 0xFE00;
	val |= 0x0092;

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_8481_LINK_SIGNAL + adj, val);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_8481_LED1_MASK + adj,
			 0x80);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_8481_LED2_MASK + adj,
			 0x18);

	/* Select activity source by Tx and Rx, as suggested by PHY AE */
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_8481_LED3_MASK + adj,
			 0x0006);

	/* Select the closest activity blink rate to that in 10/100/1000 */
	bnx2x_cl45_write(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_8481_LED3_BLINK + adj,
			0);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_84823_CTL_LED_CTL_1 + adj, &val);
	val |= MDIO_PMA_REG_84823_LED3_STRETCH_EN; /* stretch_en for LED3*/

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_84823_CTL_LED_CTL_1 + adj, val);

	/* 'Interrupt Mask' */
	bnx2x_cl45_write(bp, phy,
			 MDIO_AN_DEVAD,
			 0xFFFB, 0xFFFD);
}

static int bnx2x_848xx_cmn_config_init(struct bnx2x_phy *phy,
				       struct link_params *params,
				       struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 autoneg_val, an_1000_val, an_10_100_val;
	/*
	 * This phy uses the NIG latch mechanism since link indication
	 * arrives through its LED4 and not via its LASI signal, so we
	 * get steady signal instead of clear on read
	 */
	bnx2x_bits_en(bp, NIG_REG_LATCH_BC_0 + params->port*4,
		      1 << NIG_LATCH_BC_ENABLE_MI_INT);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x0000);

	bnx2x_848xx_set_led(bp, phy);

	/* set 1000 speed advertisement */
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_8481_1000T_CTRL,
			&an_1000_val);

	bnx2x_ext_phy_set_pause(params, phy, vars);
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD,
			MDIO_AN_REG_8481_LEGACY_AN_ADV,
			&an_10_100_val);
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_8481_LEGACY_MII_CTRL,
			&autoneg_val);
	/* Disable forced speed */
	autoneg_val &= ~((1<<6) | (1<<8) | (1<<9) | (1<<12) | (1<<13));
	an_10_100_val &= ~((1<<5) | (1<<6) | (1<<7) | (1<<8));

	if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
	     (phy->speed_cap_mask &
	     PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) ||
	    (phy->req_line_speed == SPEED_1000)) {
		an_1000_val |= (1<<8);
		autoneg_val |= (1<<9 | 1<<12);
		if (phy->req_duplex == DUPLEX_FULL)
			an_1000_val |= (1<<9);
		DP(NETIF_MSG_LINK, "Advertising 1G\n");
	} else
		an_1000_val &= ~((1<<8) | (1<<9));

	bnx2x_cl45_write(bp, phy,
			 MDIO_AN_DEVAD, MDIO_AN_REG_8481_1000T_CTRL,
			 an_1000_val);

	/* set 10 speed advertisement */
	if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
	     (phy->speed_cap_mask &
	     (PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL |
	      PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)))) {
		an_10_100_val |= (1<<7);
		/* Enable autoneg and restart autoneg for legacy speeds */
		autoneg_val |= (1<<9 | 1<<12);

		if (phy->req_duplex == DUPLEX_FULL)
			an_10_100_val |= (1<<8);
		DP(NETIF_MSG_LINK, "Advertising 100M\n");
	}
	/* set 10 speed advertisement */
	if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
	    (phy->speed_cap_mask &
	  (PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL |
	   PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF)))) {
		an_10_100_val |= (1<<5);
		autoneg_val |= (1<<9 | 1<<12);
		if (phy->req_duplex == DUPLEX_FULL)
			an_10_100_val |= (1<<6);
		DP(NETIF_MSG_LINK, "Advertising 10M\n");
	}

	/* Only 10/100 are allowed to work in FORCE mode */
	if (phy->req_line_speed == SPEED_100) {
		autoneg_val |= (1<<13);
		/* Enabled AUTO-MDIX when autoneg is disabled */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_8481_AUX_CTRL,
				 (1<<15 | 1<<9 | 7<<0));
		DP(NETIF_MSG_LINK, "Setting 100M force\n");
	}
	if (phy->req_line_speed == SPEED_10) {
		/* Enabled AUTO-MDIX when autoneg is disabled */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_8481_AUX_CTRL,
				 (1<<15 | 1<<9 | 7<<0));
		DP(NETIF_MSG_LINK, "Setting 10M force\n");
	}

	bnx2x_cl45_write(bp, phy,
			 MDIO_AN_DEVAD, MDIO_AN_REG_8481_LEGACY_AN_ADV,
			 an_10_100_val);

	if (phy->req_duplex == DUPLEX_FULL)
		autoneg_val |= (1<<8);

	bnx2x_cl45_write(bp, phy,
			 MDIO_AN_DEVAD,
			 MDIO_AN_REG_8481_LEGACY_MII_CTRL, autoneg_val);

	if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
	    (phy->speed_cap_mask &
	     PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) ||
		(phy->req_line_speed == SPEED_10000)) {
		DP(NETIF_MSG_LINK, "Advertising 10G\n");
		/* Restart autoneg for 10G*/

		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL,
				 0x3200);
	} else if (phy->req_line_speed != SPEED_10 &&
		   phy->req_line_speed != SPEED_100) {
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD,
				 MDIO_AN_REG_8481_10GBASE_T_AN_CTRL,
				 1);
	}
	/* Save spirom version */
	bnx2x_save_848xx_spirom_version(phy, params);

	return 0;
}

static int bnx2x_8481_config_init(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	/* Restore normal power mode*/
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);

	/* HW reset */
	bnx2x_ext_phy_hw_reset(bp, params->port);
	bnx2x_wait_reset_complete(bp, phy, params);

	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
	return bnx2x_848xx_cmn_config_init(phy, params, vars);
}

static int bnx2x_848x3_config_init(struct bnx2x_phy *phy,
				   struct link_params *params,
				   struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u8 port, initialize = 1;
	u16 val, adj;
	u16 temp;
	u32 actual_phy_selection, cms_enable;
	int rc = 0;

	/* This is just for MDIO_CTL_REG_84823_MEDIA register. */
	adj = 0;
	if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
		adj = 3;

	msleep(1);
	if (CHIP_IS_E2(bp))
		port = BP_PATH(bp);
	else
		port = params->port;
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH,
		       port);
	bnx2x_wait_reset_complete(bp, phy, params);
	/* Wait for GPHY to come out of reset */
	msleep(50);
	/*
	 * BCM84823 requires that XGXS links up first @ 10G for normal behavior
	 */
	temp = vars->line_speed;
	vars->line_speed = SPEED_10000;
	bnx2x_set_autoneg(&params->phy[INT_PHY], params, vars, 0);
	bnx2x_program_serdes(&params->phy[INT_PHY], params, vars);
	vars->line_speed = temp;

	/* Set dual-media configuration according to configuration */

	bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
			MDIO_CTL_REG_84823_MEDIA + adj, &val);
	val &= ~(MDIO_CTL_REG_84823_MEDIA_MAC_MASK |
		 MDIO_CTL_REG_84823_MEDIA_LINE_MASK |
		 MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN |
		 MDIO_CTL_REG_84823_MEDIA_PRIORITY_MASK |
		 MDIO_CTL_REG_84823_MEDIA_FIBER_1G);
	val |= MDIO_CTL_REG_84823_CTRL_MAC_XFI |
		MDIO_CTL_REG_84823_MEDIA_LINE_XAUI_L;

	actual_phy_selection = bnx2x_phy_selection(params);

	switch (actual_phy_selection) {
	case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT:
		/* Do nothing. Essentially this is like the priority copper */
		break;
	case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
		val |= MDIO_CTL_REG_84823_MEDIA_PRIORITY_COPPER;
		break;
	case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
		val |= MDIO_CTL_REG_84823_MEDIA_PRIORITY_FIBER;
		break;
	case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY:
		/* Do nothing here. The first PHY won't be initialized at all */
		break;
	case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY:
		val |= MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN;
		initialize = 0;
		break;
	}
	if (params->phy[EXT_PHY2].req_line_speed == SPEED_1000)
		val |= MDIO_CTL_REG_84823_MEDIA_FIBER_1G;

	bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
			 MDIO_CTL_REG_84823_MEDIA + adj, val);
	DP(NETIF_MSG_LINK, "Multi_phy config = 0x%x, Media control = 0x%x\n",
		   params->multi_phy_config, val);

	if (initialize)
		rc = bnx2x_848xx_cmn_config_init(phy, params, vars);
	else
		bnx2x_save_848xx_spirom_version(phy, params);
	cms_enable = REG_RD(bp, params->shmem_base +
			offsetof(struct shmem_region,
			dev_info.port_hw_config[params->port].default_cfg)) &
			PORT_HW_CFG_ENABLE_CMS_MASK;

	bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD,
		MDIO_CTL_REG_84823_USER_CTRL_REG, &val);
	if (cms_enable)
		val |= MDIO_CTL_REG_84823_USER_CTRL_CMS;
	else
		val &= ~MDIO_CTL_REG_84823_USER_CTRL_CMS;
	bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD,
		MDIO_CTL_REG_84823_USER_CTRL_REG, val);


	return rc;
}

static u8 bnx2x_848xx_read_status(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u16 val, val1, val2, adj;
	u8 link_up = 0;

	/* Reg offset adjustment for 84833 */
	adj = 0;
	if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
		adj = -1;

	/* Check 10G-BaseT link status */
	/* Check PMD signal ok */
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, 0xFFFA, &val1);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_PMD_SIGNAL + adj,
			&val2);
	DP(NETIF_MSG_LINK, "BCM848xx: PMD_SIGNAL 1.a811 = 0x%x\n", val2);

	/* Check link 10G */
	if (val2 & (1<<11)) {
		vars->line_speed = SPEED_10000;
		vars->duplex = DUPLEX_FULL;
		link_up = 1;
		bnx2x_ext_phy_10G_an_resolve(bp, phy, vars);
	} else { /* Check Legacy speed link */
		u16 legacy_status, legacy_speed;

		/* Enable expansion register 0x42 (Operation mode status) */
		bnx2x_cl45_write(bp, phy,
				 MDIO_AN_DEVAD,
				 MDIO_AN_REG_8481_EXPANSION_REG_ACCESS, 0xf42);

		/* Get legacy speed operation status */
		bnx2x_cl45_read(bp, phy,
				MDIO_AN_DEVAD,
				MDIO_AN_REG_8481_EXPANSION_REG_RD_RW,
				&legacy_status);

		DP(NETIF_MSG_LINK, "Legacy speed status"
			     " = 0x%x\n", legacy_status);
		link_up = ((legacy_status & (1<<11)) == (1<<11));
		if (link_up) {
			legacy_speed = (legacy_status & (3<<9));
			if (legacy_speed == (0<<9))
				vars->line_speed = SPEED_10;
			else if (legacy_speed == (1<<9))
				vars->line_speed = SPEED_100;
			else if (legacy_speed == (2<<9))
				vars->line_speed = SPEED_1000;
			else /* Should not happen */
				vars->line_speed = 0;

			if (legacy_status & (1<<8))
				vars->duplex = DUPLEX_FULL;
			else
				vars->duplex = DUPLEX_HALF;

			DP(NETIF_MSG_LINK, "Link is up in %dMbps,"
				   " is_duplex_full= %d\n", vars->line_speed,
				   (vars->duplex == DUPLEX_FULL));
			/* Check legacy speed AN resolution */
			bnx2x_cl45_read(bp, phy,
					MDIO_AN_DEVAD,
					MDIO_AN_REG_8481_LEGACY_MII_STATUS,
					&val);
			if (val & (1<<5))
				vars->link_status |=
					LINK_STATUS_AUTO_NEGOTIATE_COMPLETE;
			bnx2x_cl45_read(bp, phy,
					MDIO_AN_DEVAD,
					MDIO_AN_REG_8481_LEGACY_AN_EXPANSION,
					&val);
			if ((val & (1<<0)) == 0)
				vars->link_status |=
					LINK_STATUS_PARALLEL_DETECTION_USED;
		}
	}
	if (link_up) {
		DP(NETIF_MSG_LINK, "BCM84823: link speed is %d\n",
			   vars->line_speed);
		bnx2x_ext_phy_resolve_fc(phy, params, vars);
	}

	return link_up;
}


static int bnx2x_848xx_format_ver(u32 raw_ver, u8 *str, u16 *len)
{
	int status = 0;
	u32 spirom_ver;
	spirom_ver = ((raw_ver & 0xF80) >> 7) << 16 | (raw_ver & 0x7F);
	status = bnx2x_format_ver(spirom_ver, str, len);
	return status;
}

static void bnx2x_8481_hw_reset(struct bnx2x_phy *phy,
				struct link_params *params)
{
	bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW, 0);
	bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW, 1);
}

static void bnx2x_8481_link_reset(struct bnx2x_phy *phy,
					struct link_params *params)
{
	bnx2x_cl45_write(params->bp, phy,
			 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x0000);
	bnx2x_cl45_write(params->bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1);
}

static void bnx2x_848x3_link_reset(struct bnx2x_phy *phy,
				   struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u8 port;
	if (CHIP_IS_E2(bp))
		port = BP_PATH(bp);
	else
		port = params->port;
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW,
		       port);
}

static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy,
				     struct link_params *params, u8 mode)
{
	struct bnx2x *bp = params->bp;
	u16 val;

	switch (mode) {
	case LED_MODE_OFF:

		DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE OFF\n", params->port);

		if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
		    SHARED_HW_CFG_LED_EXTPHY1) {

			/* Set LED masks */
			bnx2x_cl45_write(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8481_LED1_MASK,
					0x0);

			bnx2x_cl45_write(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8481_LED2_MASK,
					0x0);

			bnx2x_cl45_write(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8481_LED3_MASK,
					0x0);

			bnx2x_cl45_write(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8481_LED5_MASK,
					0x0);

		} else {
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED1_MASK,
					 0x0);
		}
		break;
	case LED_MODE_FRONT_PANEL_OFF:

		DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE FRONT PANEL OFF\n",
		   params->port);

		if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
		    SHARED_HW_CFG_LED_EXTPHY1) {

			/* Set LED masks */
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED1_MASK,
					 0x0);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED2_MASK,
					 0x0);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED3_MASK,
					 0x0);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED5_MASK,
					 0x20);

		} else {
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED1_MASK,
					 0x0);
		}
		break;
	case LED_MODE_ON:

		DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE ON\n", params->port);

		if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
		    SHARED_HW_CFG_LED_EXTPHY1) {
			/* Set control reg */
			bnx2x_cl45_read(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8481_LINK_SIGNAL,
					&val);
			val &= 0x8000;
			val |= 0x2492;

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LINK_SIGNAL,
					 val);

			/* Set LED masks */
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED1_MASK,
					 0x0);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED2_MASK,
					 0x20);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED3_MASK,
					 0x20);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED5_MASK,
					 0x0);
		} else {
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED1_MASK,
					 0x20);
		}
		break;

	case LED_MODE_OPER:

		DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE OPER\n", params->port);

		if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) ==
		    SHARED_HW_CFG_LED_EXTPHY1) {

			/* Set control reg */
			bnx2x_cl45_read(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8481_LINK_SIGNAL,
					&val);

			if (!((val &
			       MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK)
			  >> MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT)) {
				DP(NETIF_MSG_LINK, "Setting LINK_SIGNAL\n");
				bnx2x_cl45_write(bp, phy,
						 MDIO_PMA_DEVAD,
						 MDIO_PMA_REG_8481_LINK_SIGNAL,
						 0xa492);
			}

			/* Set LED masks */
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED1_MASK,
					 0x10);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED2_MASK,
					 0x80);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED3_MASK,
					 0x98);

			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED5_MASK,
					 0x40);

		} else {
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LED1_MASK,
					 0x80);

			/* Tell LED3 to blink on source */
			bnx2x_cl45_read(bp, phy,
					MDIO_PMA_DEVAD,
					MDIO_PMA_REG_8481_LINK_SIGNAL,
					&val);
			val &= ~(7<<6);
			val |= (1<<6); /* A83B[8:6]= 1 */
			bnx2x_cl45_write(bp, phy,
					 MDIO_PMA_DEVAD,
					 MDIO_PMA_REG_8481_LINK_SIGNAL,
					 val);
		}
		break;
	}
}
/******************************************************************/
/*			SFX7101 PHY SECTION			  */
/******************************************************************/
static void bnx2x_7101_config_loopback(struct bnx2x_phy *phy,
				       struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	/* SFX7101_XGXS_TEST1 */
	bnx2x_cl45_write(bp, phy,
			 MDIO_XS_DEVAD, MDIO_XS_SFX7101_XGXS_TEST1, 0x100);
}

static int bnx2x_7101_config_init(struct bnx2x_phy *phy,
				  struct link_params *params,
				  struct link_vars *vars)
{
	u16 fw_ver1, fw_ver2, val;
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "Setting the SFX7101 LASI indication\n");

	/* Restore normal power mode*/
	bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port);
	/* HW reset */
	bnx2x_ext_phy_hw_reset(bp, params->port);
	bnx2x_wait_reset_complete(bp, phy, params);

	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 0x1);
	DP(NETIF_MSG_LINK, "Setting the SFX7101 LED to blink on traffic\n");
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD, MDIO_PMA_REG_7107_LED_CNTL, (1<<3));

	bnx2x_ext_phy_set_pause(params, phy, vars);
	/* Restart autoneg */
	bnx2x_cl45_read(bp, phy,
			MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, &val);
	val |= 0x200;
	bnx2x_cl45_write(bp, phy,
			 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, val);

	/* Save spirom version */
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_7101_VER1, &fw_ver1);

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_7101_VER2, &fw_ver2);
	bnx2x_save_spirom_version(bp, params->port,
				  (u32)(fw_ver1<<16 | fw_ver2), phy->ver_addr);
	return 0;
}

static u8 bnx2x_7101_read_status(struct bnx2x_phy *phy,
				 struct link_params *params,
				 struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	u8 link_up;
	u16 val1, val2;
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val2);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val1);
	DP(NETIF_MSG_LINK, "10G-base-T LASI status 0x%x->0x%x\n",
		   val2, val1);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2);
	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1);
	DP(NETIF_MSG_LINK, "10G-base-T PMA status 0x%x->0x%x\n",
		   val2, val1);
	link_up = ((val1 & 4) == 4);
	/* if link is up print the AN outcome of the SFX7101 PHY */
	if (link_up) {
		bnx2x_cl45_read(bp, phy,
				MDIO_AN_DEVAD, MDIO_AN_REG_MASTER_STATUS,
				&val2);
		vars->line_speed = SPEED_10000;
		vars->duplex = DUPLEX_FULL;
		DP(NETIF_MSG_LINK, "SFX7101 AN status 0x%x->Master=%x\n",
			   val2, (val2 & (1<<14)));
		bnx2x_ext_phy_10G_an_resolve(bp, phy, vars);
		bnx2x_ext_phy_resolve_fc(phy, params, vars);
	}
	return link_up;
}

static int bnx2x_7101_format_ver(u32 spirom_ver, u8 *str, u16 *len)
{
	if (*len < 5)
		return -EINVAL;
	str[0] = (spirom_ver & 0xFF);
	str[1] = (spirom_ver & 0xFF00) >> 8;
	str[2] = (spirom_ver & 0xFF0000) >> 16;
	str[3] = (spirom_ver & 0xFF000000) >> 24;
	str[4] = '\0';
	*len -= 5;
	return 0;
}

void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy)
{
	u16 val, cnt;

	bnx2x_cl45_read(bp, phy,
			MDIO_PMA_DEVAD,
			MDIO_PMA_REG_7101_RESET, &val);

	for (cnt = 0; cnt < 10; cnt++) {
		msleep(50);
		/* Writes a self-clearing reset */
		bnx2x_cl45_write(bp, phy,
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_7101_RESET,
				 (val | (1<<15)));
		/* Wait for clear */
		bnx2x_cl45_read(bp, phy,
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_7101_RESET, &val);

		if ((val & (1<<15)) == 0)
			break;
	}
}

static void bnx2x_7101_hw_reset(struct bnx2x_phy *phy,
				struct link_params *params) {
	/* Low power mode is controlled by GPIO 2 */
	bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_2,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
	/* The PHY reset is controlled by GPIO 1 */
	bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1,
		       MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port);
}

static void bnx2x_7101_set_link_led(struct bnx2x_phy *phy,
				    struct link_params *params, u8 mode)
{
	u16 val = 0;
	struct bnx2x *bp = params->bp;
	switch (mode) {
	case LED_MODE_FRONT_PANEL_OFF:
	case LED_MODE_OFF:
		val = 2;
		break;
	case LED_MODE_ON:
		val = 1;
		break;
	case LED_MODE_OPER:
		val = 0;
		break;
	}
	bnx2x_cl45_write(bp, phy,
			 MDIO_PMA_DEVAD,
			 MDIO_PMA_REG_7107_LINK_LED_CNTL,
			 val);
}

/******************************************************************/
/*			STATIC PHY DECLARATION			  */
/******************************************************************/

static struct bnx2x_phy phy_null = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN,
	.addr		= 0,
	.flags		= FLAGS_INIT_XGXS_FIRST,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= 0,
	.media_type	= ETH_PHY_NOT_PRESENT,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)NULL,
	.read_status	= (read_status_t)NULL,
	.link_reset	= (link_reset_t)NULL,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)NULL,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)NULL,
	.phy_specific_func = (phy_specific_func_t)NULL
};

static struct bnx2x_phy phy_serdes = {
	.type		= PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT,
	.addr		= 0xff,
	.flags		= 0,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10baseT_Half |
			   SUPPORTED_10baseT_Full |
			   SUPPORTED_100baseT_Half |
			   SUPPORTED_100baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_2500baseX_Full |
			   SUPPORTED_TP |
			   SUPPORTED_Autoneg |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_BASE_T,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_init_serdes,
	.read_status	= (read_status_t)bnx2x_link_settings_status,
	.link_reset	= (link_reset_t)bnx2x_int_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)NULL,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)NULL,
	.phy_specific_func = (phy_specific_func_t)NULL
};

static struct bnx2x_phy phy_xgxs = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT,
	.addr		= 0xff,
	.flags		= 0,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10baseT_Half |
			   SUPPORTED_10baseT_Full |
			   SUPPORTED_100baseT_Half |
			   SUPPORTED_100baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_2500baseX_Full |
			   SUPPORTED_10000baseT_Full |
			   SUPPORTED_FIBRE |
			   SUPPORTED_Autoneg |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_CX4,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_init_xgxs,
	.read_status	= (read_status_t)bnx2x_link_settings_status,
	.link_reset	= (link_reset_t)bnx2x_int_link_reset,
	.config_loopback = (config_loopback_t)bnx2x_set_xgxs_loopback,
	.format_fw_ver	= (format_fw_ver_t)NULL,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)NULL,
	.phy_specific_func = (phy_specific_func_t)NULL
};

static struct bnx2x_phy phy_7101 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101,
	.addr		= 0xff,
	.flags		= FLAGS_FAN_FAILURE_DET_REQ,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10000baseT_Full |
			   SUPPORTED_TP |
			   SUPPORTED_Autoneg |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_BASE_T,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_7101_config_init,
	.read_status	= (read_status_t)bnx2x_7101_read_status,
	.link_reset	= (link_reset_t)bnx2x_common_ext_link_reset,
	.config_loopback = (config_loopback_t)bnx2x_7101_config_loopback,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_7101_format_ver,
	.hw_reset	= (hw_reset_t)bnx2x_7101_hw_reset,
	.set_link_led	= (set_link_led_t)bnx2x_7101_set_link_led,
	.phy_specific_func = (phy_specific_func_t)NULL
};
static struct bnx2x_phy phy_8073 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
	.addr		= 0xff,
	.flags		= FLAGS_HW_LOCK_REQUIRED,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10000baseT_Full |
			   SUPPORTED_2500baseX_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_FIBRE |
			   SUPPORTED_Autoneg |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_KR,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_8073_config_init,
	.read_status	= (read_status_t)bnx2x_8073_read_status,
	.link_reset	= (link_reset_t)bnx2x_8073_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_format_ver,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)NULL,
	.phy_specific_func = (phy_specific_func_t)NULL
};
static struct bnx2x_phy phy_8705 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705,
	.addr		= 0xff,
	.flags		= FLAGS_INIT_XGXS_FIRST,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10000baseT_Full |
			   SUPPORTED_FIBRE |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_XFP_FIBER,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_8705_config_init,
	.read_status	= (read_status_t)bnx2x_8705_read_status,
	.link_reset	= (link_reset_t)bnx2x_common_ext_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_null_format_ver,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)NULL,
	.phy_specific_func = (phy_specific_func_t)NULL
};
static struct bnx2x_phy phy_8706 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706,
	.addr		= 0xff,
	.flags		= FLAGS_INIT_XGXS_FIRST,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10000baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_FIBRE |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_SFP_FIBER,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_8706_config_init,
	.read_status	= (read_status_t)bnx2x_8706_read_status,
	.link_reset	= (link_reset_t)bnx2x_common_ext_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_format_ver,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)NULL,
	.phy_specific_func = (phy_specific_func_t)NULL
};

static struct bnx2x_phy phy_8726 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
	.addr		= 0xff,
	.flags		= (FLAGS_HW_LOCK_REQUIRED |
			   FLAGS_INIT_XGXS_FIRST),
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10000baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_Autoneg |
			   SUPPORTED_FIBRE |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_NOT_PRESENT,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_8726_config_init,
	.read_status	= (read_status_t)bnx2x_8726_read_status,
	.link_reset	= (link_reset_t)bnx2x_8726_link_reset,
	.config_loopback = (config_loopback_t)bnx2x_8726_config_loopback,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_format_ver,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)NULL,
	.phy_specific_func = (phy_specific_func_t)NULL
};

static struct bnx2x_phy phy_8727 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727,
	.addr		= 0xff,
	.flags		= FLAGS_FAN_FAILURE_DET_REQ,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10000baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_FIBRE |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_NOT_PRESENT,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_8727_config_init,
	.read_status	= (read_status_t)bnx2x_8727_read_status,
	.link_reset	= (link_reset_t)bnx2x_8727_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_format_ver,
	.hw_reset	= (hw_reset_t)bnx2x_8727_hw_reset,
	.set_link_led	= (set_link_led_t)bnx2x_8727_set_link_led,
	.phy_specific_func = (phy_specific_func_t)bnx2x_8727_specific_func
};
static struct bnx2x_phy phy_8481 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481,
	.addr		= 0xff,
	.flags		= FLAGS_FAN_FAILURE_DET_REQ |
			  FLAGS_REARM_LATCH_SIGNAL,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10baseT_Half |
			   SUPPORTED_10baseT_Full |
			   SUPPORTED_100baseT_Half |
			   SUPPORTED_100baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_10000baseT_Full |
			   SUPPORTED_TP |
			   SUPPORTED_Autoneg |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_BASE_T,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_8481_config_init,
	.read_status	= (read_status_t)bnx2x_848xx_read_status,
	.link_reset	= (link_reset_t)bnx2x_8481_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_848xx_format_ver,
	.hw_reset	= (hw_reset_t)bnx2x_8481_hw_reset,
	.set_link_led	= (set_link_led_t)bnx2x_848xx_set_link_led,
	.phy_specific_func = (phy_specific_func_t)NULL
};

static struct bnx2x_phy phy_84823 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823,
	.addr		= 0xff,
	.flags		= FLAGS_FAN_FAILURE_DET_REQ |
			  FLAGS_REARM_LATCH_SIGNAL,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10baseT_Half |
			   SUPPORTED_10baseT_Full |
			   SUPPORTED_100baseT_Half |
			   SUPPORTED_100baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_10000baseT_Full |
			   SUPPORTED_TP |
			   SUPPORTED_Autoneg |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_BASE_T,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_848x3_config_init,
	.read_status	= (read_status_t)bnx2x_848xx_read_status,
	.link_reset	= (link_reset_t)bnx2x_848x3_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_848xx_format_ver,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)bnx2x_848xx_set_link_led,
	.phy_specific_func = (phy_specific_func_t)NULL
};

static struct bnx2x_phy phy_84833 = {
	.type		= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833,
	.addr		= 0xff,
	.flags		= FLAGS_FAN_FAILURE_DET_REQ |
			    FLAGS_REARM_LATCH_SIGNAL,
	.def_md_devad	= 0,
	.reserved	= 0,
	.rx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.tx_preemphasis	= {0xffff, 0xffff, 0xffff, 0xffff},
	.mdio_ctrl	= 0,
	.supported	= (SUPPORTED_10baseT_Half |
			   SUPPORTED_10baseT_Full |
			   SUPPORTED_100baseT_Half |
			   SUPPORTED_100baseT_Full |
			   SUPPORTED_1000baseT_Full |
			   SUPPORTED_10000baseT_Full |
			   SUPPORTED_TP |
			   SUPPORTED_Autoneg |
			   SUPPORTED_Pause |
			   SUPPORTED_Asym_Pause),
	.media_type	= ETH_PHY_BASE_T,
	.ver_addr	= 0,
	.req_flow_ctrl	= 0,
	.req_line_speed	= 0,
	.speed_cap_mask	= 0,
	.req_duplex	= 0,
	.rsrv		= 0,
	.config_init	= (config_init_t)bnx2x_848x3_config_init,
	.read_status	= (read_status_t)bnx2x_848xx_read_status,
	.link_reset	= (link_reset_t)bnx2x_848x3_link_reset,
	.config_loopback = (config_loopback_t)NULL,
	.format_fw_ver	= (format_fw_ver_t)bnx2x_848xx_format_ver,
	.hw_reset	= (hw_reset_t)NULL,
	.set_link_led	= (set_link_led_t)bnx2x_848xx_set_link_led,
	.phy_specific_func = (phy_specific_func_t)NULL
};

/*****************************************************************/
/*                                                               */
/* Populate the phy according. Main function: bnx2x_populate_phy   */
/*                                                               */
/*****************************************************************/

static void bnx2x_populate_preemphasis(struct bnx2x *bp, u32 shmem_base,
				     struct bnx2x_phy *phy, u8 port,
				     u8 phy_index)
{
	/* Get the 4 lanes xgxs config rx and tx */
	u32 rx = 0, tx = 0, i;
	for (i = 0; i < 2; i++) {
		/*
		 * INT_PHY and EXT_PHY1 share the same value location in the
		 * shmem. When num_phys is greater than 1, than this value
		 * applies only to EXT_PHY1
		 */
		if (phy_index == INT_PHY || phy_index == EXT_PHY1) {
			rx = REG_RD(bp, shmem_base +
				    offsetof(struct shmem_region,
			  dev_info.port_hw_config[port].xgxs_config_rx[i<<1]));

			tx = REG_RD(bp, shmem_base +
				    offsetof(struct shmem_region,
			  dev_info.port_hw_config[port].xgxs_config_tx[i<<1]));
		} else {
			rx = REG_RD(bp, shmem_base +
				    offsetof(struct shmem_region,
			 dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));

			tx = REG_RD(bp, shmem_base +
				    offsetof(struct shmem_region,
			 dev_info.port_hw_config[port].xgxs_config2_rx[i<<1]));
		}

		phy->rx_preemphasis[i << 1] = ((rx>>16) & 0xffff);
		phy->rx_preemphasis[(i << 1) + 1] = (rx & 0xffff);

		phy->tx_preemphasis[i << 1] = ((tx>>16) & 0xffff);
		phy->tx_preemphasis[(i << 1) + 1] = (tx & 0xffff);
	}
}

static u32 bnx2x_get_ext_phy_config(struct bnx2x *bp, u32 shmem_base,
				    u8 phy_index, u8 port)
{
	u32 ext_phy_config = 0;
	switch (phy_index) {
	case EXT_PHY1:
		ext_phy_config = REG_RD(bp, shmem_base +
					      offsetof(struct shmem_region,
			dev_info.port_hw_config[port].external_phy_config));
		break;
	case EXT_PHY2:
		ext_phy_config = REG_RD(bp, shmem_base +
					      offsetof(struct shmem_region,
			dev_info.port_hw_config[port].external_phy_config2));
		break;
	default:
		DP(NETIF_MSG_LINK, "Invalid phy_index %d\n", phy_index);
		return -EINVAL;
	}

	return ext_phy_config;
}
static int bnx2x_populate_int_phy(struct bnx2x *bp, u32 shmem_base, u8 port,
				  struct bnx2x_phy *phy)
{
	u32 phy_addr;
	u32 chip_id;
	u32 switch_cfg = (REG_RD(bp, shmem_base +
				       offsetof(struct shmem_region,
			dev_info.port_feature_config[port].link_config)) &
			  PORT_FEATURE_CONNECTED_SWITCH_MASK);
	chip_id = REG_RD(bp, MISC_REG_CHIP_NUM) << 16;
	switch (switch_cfg) {
	case SWITCH_CFG_1G:
		phy_addr = REG_RD(bp,
					NIG_REG_SERDES0_CTRL_PHY_ADDR +
					port * 0x10);
		*phy = phy_serdes;
		break;
	case SWITCH_CFG_10G:
		phy_addr = REG_RD(bp,
					NIG_REG_XGXS0_CTRL_PHY_ADDR +
					port * 0x18);
		*phy = phy_xgxs;
		break;
	default:
		DP(NETIF_MSG_LINK, "Invalid switch_cfg\n");
		return -EINVAL;
	}
	phy->addr = (u8)phy_addr;
	phy->mdio_ctrl = bnx2x_get_emac_base(bp,
					    SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH,
					    port);
	if (CHIP_IS_E2(bp))
		phy->def_md_devad = E2_DEFAULT_PHY_DEV_ADDR;
	else
		phy->def_md_devad = DEFAULT_PHY_DEV_ADDR;

	DP(NETIF_MSG_LINK, "Internal phy port=%d, addr=0x%x, mdio_ctl=0x%x\n",
		   port, phy->addr, phy->mdio_ctrl);

	bnx2x_populate_preemphasis(bp, shmem_base, phy, port, INT_PHY);
	return 0;
}

static int bnx2x_populate_ext_phy(struct bnx2x *bp,
				  u8 phy_index,
				  u32 shmem_base,
				  u32 shmem2_base,
				  u8 port,
				  struct bnx2x_phy *phy)
{
	u32 ext_phy_config, phy_type, config2;
	u32 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH;
	ext_phy_config = bnx2x_get_ext_phy_config(bp, shmem_base,
						  phy_index, port);
	phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config);
	/* Select the phy type */
	switch (phy_type) {
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
		mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_SWAPPED;
		*phy = phy_8073;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
		*phy = phy_8705;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
		*phy = phy_8706;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
		mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1;
		*phy = phy_8726;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC:
		/* BCM8727_NOC => BCM8727 no over current */
		mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1;
		*phy = phy_8727;
		phy->flags |= FLAGS_NOC;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
		mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1;
		*phy = phy_8727;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
		*phy = phy_8481;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823:
		*phy = phy_84823;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833:
		*phy = phy_84833;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
		*phy = phy_7101;
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
		*phy = phy_null;
		return -EINVAL;
	default:
		*phy = phy_null;
		return 0;
	}

	phy->addr = XGXS_EXT_PHY_ADDR(ext_phy_config);
	bnx2x_populate_preemphasis(bp, shmem_base, phy, port, phy_index);

	/*
	 * The shmem address of the phy version is located on different
	 * structures. In case this structure is too old, do not set
	 * the address
	 */
	config2 = REG_RD(bp, shmem_base + offsetof(struct shmem_region,
					dev_info.shared_hw_config.config2));
	if (phy_index == EXT_PHY1) {
		phy->ver_addr = shmem_base + offsetof(struct shmem_region,
				port_mb[port].ext_phy_fw_version);

		/* Check specific mdc mdio settings */
		if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK)
			mdc_mdio_access = config2 &
			SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK;
	} else {
		u32 size = REG_RD(bp, shmem2_base);

		if (size >
		    offsetof(struct shmem2_region, ext_phy_fw_version2)) {
			phy->ver_addr = shmem2_base +
			    offsetof(struct shmem2_region,
				     ext_phy_fw_version2[port]);
		}
		/* Check specific mdc mdio settings */
		if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS2_MASK)
			mdc_mdio_access = (config2 &
			SHARED_HW_CFG_MDC_MDIO_ACCESS2_MASK) >>
			(SHARED_HW_CFG_MDC_MDIO_ACCESS2_SHIFT -
			 SHARED_HW_CFG_MDC_MDIO_ACCESS1_SHIFT);
	}
	phy->mdio_ctrl = bnx2x_get_emac_base(bp, mdc_mdio_access, port);

	/*
	 * In case mdc/mdio_access of the external phy is different than the
	 * mdc/mdio access of the XGXS, a HW lock must be taken in each access
	 * to prevent one port interfere with another port's CL45 operations.
	 */
	if (mdc_mdio_access != SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH)
		phy->flags |= FLAGS_HW_LOCK_REQUIRED;
	DP(NETIF_MSG_LINK, "phy_type 0x%x port %d found in index %d\n",
		   phy_type, port, phy_index);
	DP(NETIF_MSG_LINK, "             addr=0x%x, mdio_ctl=0x%x\n",
		   phy->addr, phy->mdio_ctrl);
	return 0;
}

static int bnx2x_populate_phy(struct bnx2x *bp, u8 phy_index, u32 shmem_base,
			      u32 shmem2_base, u8 port, struct bnx2x_phy *phy)
{
	int status = 0;
	phy->type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN;
	if (phy_index == INT_PHY)
		return bnx2x_populate_int_phy(bp, shmem_base, port, phy);
	status = bnx2x_populate_ext_phy(bp, phy_index, shmem_base, shmem2_base,
					port, phy);
	return status;
}

static void bnx2x_phy_def_cfg(struct link_params *params,
			      struct bnx2x_phy *phy,
			      u8 phy_index)
{
	struct bnx2x *bp = params->bp;
	u32 link_config;
	/* Populate the default phy configuration for MF mode */
	if (phy_index == EXT_PHY2) {
		link_config = REG_RD(bp, params->shmem_base +
				     offsetof(struct shmem_region, dev_info.
			port_feature_config[params->port].link_config2));
		phy->speed_cap_mask = REG_RD(bp, params->shmem_base +
					     offsetof(struct shmem_region,
						      dev_info.
			port_hw_config[params->port].speed_capability_mask2));
	} else {
		link_config = REG_RD(bp, params->shmem_base +
				     offsetof(struct shmem_region, dev_info.
				port_feature_config[params->port].link_config));
		phy->speed_cap_mask = REG_RD(bp, params->shmem_base +
					     offsetof(struct shmem_region,
						      dev_info.
			port_hw_config[params->port].speed_capability_mask));
	}
	DP(NETIF_MSG_LINK, "Default config phy idx %x cfg 0x%x speed_cap_mask"
		       " 0x%x\n", phy_index, link_config, phy->speed_cap_mask);

	phy->req_duplex = DUPLEX_FULL;
	switch (link_config  & PORT_FEATURE_LINK_SPEED_MASK) {
	case PORT_FEATURE_LINK_SPEED_10M_HALF:
		phy->req_duplex = DUPLEX_HALF;
	case PORT_FEATURE_LINK_SPEED_10M_FULL:
		phy->req_line_speed = SPEED_10;
		break;
	case PORT_FEATURE_LINK_SPEED_100M_HALF:
		phy->req_duplex = DUPLEX_HALF;
	case PORT_FEATURE_LINK_SPEED_100M_FULL:
		phy->req_line_speed = SPEED_100;
		break;
	case PORT_FEATURE_LINK_SPEED_1G:
		phy->req_line_speed = SPEED_1000;
		break;
	case PORT_FEATURE_LINK_SPEED_2_5G:
		phy->req_line_speed = SPEED_2500;
		break;
	case PORT_FEATURE_LINK_SPEED_10G_CX4:
		phy->req_line_speed = SPEED_10000;
		break;
	default:
		phy->req_line_speed = SPEED_AUTO_NEG;
		break;
	}

	switch (link_config  & PORT_FEATURE_FLOW_CONTROL_MASK) {
	case PORT_FEATURE_FLOW_CONTROL_AUTO:
		phy->req_flow_ctrl = BNX2X_FLOW_CTRL_AUTO;
		break;
	case PORT_FEATURE_FLOW_CONTROL_TX:
		phy->req_flow_ctrl = BNX2X_FLOW_CTRL_TX;
		break;
	case PORT_FEATURE_FLOW_CONTROL_RX:
		phy->req_flow_ctrl = BNX2X_FLOW_CTRL_RX;
		break;
	case PORT_FEATURE_FLOW_CONTROL_BOTH:
		phy->req_flow_ctrl = BNX2X_FLOW_CTRL_BOTH;
		break;
	default:
		phy->req_flow_ctrl = BNX2X_FLOW_CTRL_NONE;
		break;
	}
}

u32 bnx2x_phy_selection(struct link_params *params)
{
	u32 phy_config_swapped, prio_cfg;
	u32 return_cfg = PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT;

	phy_config_swapped = params->multi_phy_config &
		PORT_HW_CFG_PHY_SWAPPED_ENABLED;

	prio_cfg = params->multi_phy_config &
			PORT_HW_CFG_PHY_SELECTION_MASK;

	if (phy_config_swapped) {
		switch (prio_cfg) {
		case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
		     return_cfg = PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY;
		     break;
		case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
		     return_cfg = PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY;
		     break;
		case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY:
		     return_cfg = PORT_HW_CFG_PHY_SELECTION_FIRST_PHY;
		     break;
		case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY:
		     return_cfg = PORT_HW_CFG_PHY_SELECTION_SECOND_PHY;
		     break;
		}
	} else
		return_cfg = prio_cfg;

	return return_cfg;
}


int bnx2x_phy_probe(struct link_params *params)
{
	u8 phy_index, actual_phy_idx, link_cfg_idx;
	u32 phy_config_swapped, sync_offset, media_types;
	struct bnx2x *bp = params->bp;
	struct bnx2x_phy *phy;
	params->num_phys = 0;
	DP(NETIF_MSG_LINK, "Begin phy probe\n");
	phy_config_swapped = params->multi_phy_config &
		PORT_HW_CFG_PHY_SWAPPED_ENABLED;

	for (phy_index = INT_PHY; phy_index < MAX_PHYS;
	      phy_index++) {
		link_cfg_idx = LINK_CONFIG_IDX(phy_index);
		actual_phy_idx = phy_index;
		if (phy_config_swapped) {
			if (phy_index == EXT_PHY1)
				actual_phy_idx = EXT_PHY2;
			else if (phy_index == EXT_PHY2)
				actual_phy_idx = EXT_PHY1;
		}
		DP(NETIF_MSG_LINK, "phy_config_swapped %x, phy_index %x,"
			       " actual_phy_idx %x\n", phy_config_swapped,
			   phy_index, actual_phy_idx);
		phy = &params->phy[actual_phy_idx];
		if (bnx2x_populate_phy(bp, phy_index, params->shmem_base,
				       params->shmem2_base, params->port,
				       phy) != 0) {
			params->num_phys = 0;
			DP(NETIF_MSG_LINK, "phy probe failed in phy index %d\n",
				   phy_index);
			for (phy_index = INT_PHY;
			      phy_index < MAX_PHYS;
			      phy_index++)
				*phy = phy_null;
			return -EINVAL;
		}
		if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)
			break;

		sync_offset = params->shmem_base +
			offsetof(struct shmem_region,
			dev_info.port_hw_config[params->port].media_type);
		media_types = REG_RD(bp, sync_offset);

		/*
		 * Update media type for non-PMF sync only for the first time
		 * In case the media type changes afterwards, it will be updated
		 * using the update_status function
		 */
		if ((media_types & (PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK <<
				    (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT *
				     actual_phy_idx))) == 0) {
			media_types |= ((phy->media_type &
					PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) <<
				(PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT *
				 actual_phy_idx));
		}
		REG_WR(bp, sync_offset, media_types);

		bnx2x_phy_def_cfg(params, phy, phy_index);
		params->num_phys++;
	}

	DP(NETIF_MSG_LINK, "End phy probe. #phys found %x\n", params->num_phys);
	return 0;
}

static void set_phy_vars(struct link_params *params)
{
	struct bnx2x *bp = params->bp;
	u8 actual_phy_idx, phy_index, link_cfg_idx;
	u8 phy_config_swapped = params->multi_phy_config &
			PORT_HW_CFG_PHY_SWAPPED_ENABLED;
	for (phy_index = INT_PHY; phy_index < params->num_phys;
	      phy_index++) {
		link_cfg_idx = LINK_CONFIG_IDX(phy_index);
		actual_phy_idx = phy_index;
		if (phy_config_swapped) {
			if (phy_index == EXT_PHY1)
				actual_phy_idx = EXT_PHY2;
			else if (phy_index == EXT_PHY2)
				actual_phy_idx = EXT_PHY1;
		}
		params->phy[actual_phy_idx].req_flow_ctrl =
			params->req_flow_ctrl[link_cfg_idx];

		params->phy[actual_phy_idx].req_line_speed =
			params->req_line_speed[link_cfg_idx];

		params->phy[actual_phy_idx].speed_cap_mask =
			params->speed_cap_mask[link_cfg_idx];

		params->phy[actual_phy_idx].req_duplex =
			params->req_duplex[link_cfg_idx];

		DP(NETIF_MSG_LINK, "req_flow_ctrl %x, req_line_speed %x,"
			   " speed_cap_mask %x\n",
			   params->phy[actual_phy_idx].req_flow_ctrl,
			   params->phy[actual_phy_idx].req_line_speed,
			   params->phy[actual_phy_idx].speed_cap_mask);
	}
}

int bnx2x_phy_init(struct link_params *params, struct link_vars *vars)
{
	struct bnx2x *bp = params->bp;
	DP(NETIF_MSG_LINK, "Phy Initialization started\n");
	DP(NETIF_MSG_LINK, "(1) req_speed %d, req_flowctrl %d\n",
		   params->req_line_speed[0], params->req_flow_ctrl[0]);
	DP(NETIF_MSG_LINK, "(2) req_speed %d, req_flowctrl %d\n",
		   params->req_line_speed[1], params->req_flow_ctrl[1]);
	vars->link_status = 0;
	vars->phy_link_up = 0;
	vars->link_up = 0;
	vars->line_speed = 0;
	vars->duplex = DUPLEX_FULL;
	vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
	vars->mac_type = MAC_TYPE_NONE;
	vars->phy_flags = 0;

	/* disable attentions */
	bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4,
		       (NIG_MASK_XGXS0_LINK_STATUS |
			NIG_MASK_XGXS0_LINK10G |
			NIG_MASK_SERDES0_LINK_STATUS |
			NIG_MASK_MI_INT));

	bnx2x_emac_init(params, vars);

	if (params->num_phys == 0) {
		DP(NETIF_MSG_LINK, "No phy found for initialization !!\n");
		return -EINVAL;
	}
	set_phy_vars(params);

	DP(NETIF_MSG_LINK, "Num of phys on board: %d\n", params->num_phys);
	if (params->loopback_mode == LOOPBACK_BMAC) {

		vars->link_up = 1;
		vars->line_speed = SPEED_10000;
		vars->duplex = DUPLEX_FULL;
		vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
		vars->mac_type = MAC_TYPE_BMAC;

		vars->phy_flags = PHY_XGXS_FLAG;

		bnx2x_xgxs_deassert(params);

		/* set bmac loopback */
		bnx2x_bmac_enable(params, vars, 1);

		REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);

	} else if (params->loopback_mode == LOOPBACK_EMAC) {

		vars->link_up = 1;
		vars->line_speed = SPEED_1000;
		vars->duplex = DUPLEX_FULL;
		vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
		vars->mac_type = MAC_TYPE_EMAC;

		vars->phy_flags = PHY_XGXS_FLAG;

		bnx2x_xgxs_deassert(params);
		/* set bmac loopback */
		bnx2x_emac_enable(params, vars, 1);
		bnx2x_emac_program(params, vars);
		REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);

	} else if ((params->loopback_mode == LOOPBACK_XGXS) ||
		   (params->loopback_mode == LOOPBACK_EXT_PHY)) {

		vars->link_up = 1;
		vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE;
		vars->duplex = DUPLEX_FULL;
		if (params->req_line_speed[0] == SPEED_1000) {
			vars->line_speed = SPEED_1000;
			vars->mac_type = MAC_TYPE_EMAC;
		} else {
			vars->line_speed = SPEED_10000;
			vars->mac_type = MAC_TYPE_BMAC;
		}

		bnx2x_xgxs_deassert(params);
		bnx2x_link_initialize(params, vars);

		if (params->req_line_speed[0] == SPEED_1000) {
			bnx2x_emac_program(params, vars);
			bnx2x_emac_enable(params, vars, 0);
		} else
			bnx2x_bmac_enable(params, vars, 0);
		if (params->loopback_mode == LOOPBACK_XGXS) {
			/* set 10G XGXS loopback */
			params->phy[INT_PHY].config_loopback(
				&params->phy[INT_PHY],
				params);

		} else {
			/* set external phy loopback */
			u8 phy_index;
			for (phy_index = EXT_PHY1;
			      phy_index < params->num_phys; phy_index++) {
				if (params->phy[phy_index].config_loopback)
					params->phy[phy_index].config_loopback(
						&params->phy[phy_index],
						params);
			}
		}
		REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);

		bnx2x_set_led(params, vars,
			      LED_MODE_OPER, vars->line_speed);
	} else
	/* No loopback */
	{
		if (params->switch_cfg == SWITCH_CFG_10G)
			bnx2x_xgxs_deassert(params);
		else
			bnx2x_serdes_deassert(bp, params->port);

		bnx2x_link_initialize(params, vars);
		msleep(30);
		bnx2x_link_int_enable(params);
	}
	return 0;
}

int bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
		     u8 reset_ext_phy)
{
	struct bnx2x *bp = params->bp;
	u8 phy_index, port = params->port, clear_latch_ind = 0;
	DP(NETIF_MSG_LINK, "Resetting the link of port %d\n", port);
	/* disable attentions */
	vars->link_status = 0;
	bnx2x_update_mng(params, vars->link_status);
	bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
		       (NIG_MASK_XGXS0_LINK_STATUS |
			NIG_MASK_XGXS0_LINK10G |
			NIG_MASK_SERDES0_LINK_STATUS |
			NIG_MASK_MI_INT));

	/* activate nig drain */
	REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);

	/* disable nig egress interface */
	REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0);
	REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0);

	/* Stop BigMac rx */
	bnx2x_bmac_rx_disable(bp, port);

	/* disable emac */
	REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);

	msleep(10);
	/* The PHY reset is controlled by GPIO 1
	 * Hold it as vars low
	 */
	 /* clear link led */
	bnx2x_set_led(params, vars, LED_MODE_OFF, 0);

	if (reset_ext_phy) {
		for (phy_index = EXT_PHY1; phy_index < params->num_phys;
		      phy_index++) {
			if (params->phy[phy_index].link_reset)
				params->phy[phy_index].link_reset(
					&params->phy[phy_index],
					params);
			if (params->phy[phy_index].flags &
			    FLAGS_REARM_LATCH_SIGNAL)
				clear_latch_ind = 1;
		}
	}

	if (clear_latch_ind) {
		/* Clear latching indication */
		bnx2x_rearm_latch_signal(bp, port, 0);
		bnx2x_bits_dis(bp, NIG_REG_LATCH_BC_0 + port*4,
			       1 << NIG_LATCH_BC_ENABLE_MI_INT);
	}
	if (params->phy[INT_PHY].link_reset)
		params->phy[INT_PHY].link_reset(
			&params->phy[INT_PHY], params);
	/* reset BigMac */
	REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
	       (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));

	/* disable nig ingress interface */
	REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0);
	REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0);
	REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0);
	REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0);
	vars->link_up = 0;
	return 0;
}

/****************************************************************************/
/*				Common function				    */
/****************************************************************************/
static int bnx2x_8073_common_init_phy(struct bnx2x *bp,
				      u32 shmem_base_path[],
				      u32 shmem2_base_path[], u8 phy_index,
				      u32 chip_id)
{
	struct bnx2x_phy phy[PORT_MAX];
	struct bnx2x_phy *phy_blk[PORT_MAX];
	u16 val;
	s8 port = 0;
	s8 port_of_path = 0;
	u32 swap_val, swap_override;
	swap_val = REG_RD(bp,  NIG_REG_PORT_SWAP);
	swap_override = REG_RD(bp,  NIG_REG_STRAP_OVERRIDE);
	port ^= (swap_val && swap_override);
	bnx2x_ext_phy_hw_reset(bp, port);
	/* PART1 - Reset both phys */
	for (port = PORT_MAX - 1; port >= PORT_0; port--) {
		u32 shmem_base, shmem2_base;
		/* In E2, same phy is using for port0 of the two paths */
		if (CHIP_IS_E2(bp)) {
			shmem_base = shmem_base_path[port];
			shmem2_base = shmem2_base_path[port];
			port_of_path = 0;
		} else {
			shmem_base = shmem_base_path[0];
			shmem2_base = shmem2_base_path[0];
			port_of_path = port;
		}

		/* Extract the ext phy address for the port */
		if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
				       port_of_path, &phy[port]) !=
		    0) {
			DP(NETIF_MSG_LINK, "populate_phy failed\n");
			return -EINVAL;
		}
		/* disable attentions */
		bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 +
			       port_of_path*4,
			       (NIG_MASK_XGXS0_LINK_STATUS |
				NIG_MASK_XGXS0_LINK10G |
				NIG_MASK_SERDES0_LINK_STATUS |
				NIG_MASK_MI_INT));

		/* Need to take the phy out of low power mode in order
			to write to access its registers */
		bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
			       MISC_REGISTERS_GPIO_OUTPUT_HIGH,
			       port);

		/* Reset the phy */
		bnx2x_cl45_write(bp, &phy[port],
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_CTRL,
				 1<<15);
	}

	/* Add delay of 150ms after reset */
	msleep(150);

	if (phy[PORT_0].addr & 0x1) {
		phy_blk[PORT_0] = &(phy[PORT_1]);
		phy_blk[PORT_1] = &(phy[PORT_0]);
	} else {
		phy_blk[PORT_0] = &(phy[PORT_0]);
		phy_blk[PORT_1] = &(phy[PORT_1]);
	}

	/* PART2 - Download firmware to both phys */
	for (port = PORT_MAX - 1; port >= PORT_0; port--) {
		if (CHIP_IS_E2(bp))
			port_of_path = 0;
		else
			port_of_path = port;

		DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n",
			   phy_blk[port]->addr);
		if (bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port],
						      port_of_path))
			return -EINVAL;

		/* Only set bit 10 = 1 (Tx power down) */
		bnx2x_cl45_read(bp, phy_blk[port],
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_TX_POWER_DOWN, &val);

		/* Phase1 of TX_POWER_DOWN reset */
		bnx2x_cl45_write(bp, phy_blk[port],
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_TX_POWER_DOWN,
				 (val | 1<<10));
	}

	/*
	 * Toggle Transmitter: Power down and then up with 600ms delay
	 * between
	 */
	msleep(600);

	/* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */
	for (port = PORT_MAX - 1; port >= PORT_0; port--) {
		/* Phase2 of POWER_DOWN_RESET */
		/* Release bit 10 (Release Tx power down) */
		bnx2x_cl45_read(bp, phy_blk[port],
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_TX_POWER_DOWN, &val);

		bnx2x_cl45_write(bp, phy_blk[port],
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10))));
		msleep(15);

		/* Read modify write the SPI-ROM version select register */
		bnx2x_cl45_read(bp, phy_blk[port],
				MDIO_PMA_DEVAD,
				MDIO_PMA_REG_EDC_FFE_MAIN, &val);
		bnx2x_cl45_write(bp, phy_blk[port],
				 MDIO_PMA_DEVAD,
				 MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12)));

		/* set GPIO2 back to LOW */
		bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
			       MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
	}
	return 0;
}
static int bnx2x_8726_common_init_phy(struct bnx2x *bp,
				      u32 shmem_base_path[],
				      u32 shmem2_base_path[], u8 phy_index,
				      u32 chip_id)
{
	u32 val;
	s8 port;
	struct bnx2x_phy phy;
	/* Use port1 because of the static port-swap */
	/* Enable the module detection interrupt */
	val = REG_RD(bp, MISC_REG_GPIO_EVENT_EN);
	val |= ((1<<MISC_REGISTERS_GPIO_3)|
		(1<<(MISC_REGISTERS_GPIO_3 + MISC_REGISTERS_GPIO_PORT_SHIFT)));
	REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val);

	bnx2x_ext_phy_hw_reset(bp, 0);
	msleep(5);
	for (port = 0; port < PORT_MAX; port++) {
		u32 shmem_base, shmem2_base;

		/* In E2, same phy is using for port0 of the two paths */
		if (CHIP_IS_E2(bp)) {
			shmem_base = shmem_base_path[port];
			shmem2_base = shmem2_base_path[port];
		} else {
			shmem_base = shmem_base_path[0];
			shmem2_base = shmem2_base_path[0];
		}
		/* Extract the ext phy address for the port */
		if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
				       port, &phy) !=
		    0) {
			DP(NETIF_MSG_LINK, "populate phy failed\n");
			return -EINVAL;
		}

		/* Reset phy*/
		bnx2x_cl45_write(bp, &phy,
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x0001);


		/* Set fault module detected LED on */
		bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
			       MISC_REGISTERS_GPIO_HIGH,
			       port);
	}

	return 0;
}
static void bnx2x_get_ext_phy_reset_gpio(struct bnx2x *bp, u32 shmem_base,
					 u8 *io_gpio, u8 *io_port)
{

	u32 phy_gpio_reset = REG_RD(bp, shmem_base +
					  offsetof(struct shmem_region,
				dev_info.port_hw_config[PORT_0].default_cfg));
	switch (phy_gpio_reset) {
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0:
		*io_gpio = 0;
		*io_port = 0;
		break;
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P0:
		*io_gpio = 1;
		*io_port = 0;
		break;
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P0:
		*io_gpio = 2;
		*io_port = 0;
		break;
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P0:
		*io_gpio = 3;
		*io_port = 0;
		break;
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P1:
		*io_gpio = 0;
		*io_port = 1;
		break;
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P1:
		*io_gpio = 1;
		*io_port = 1;
		break;
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P1:
		*io_gpio = 2;
		*io_port = 1;
		break;
	case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P1:
		*io_gpio = 3;
		*io_port = 1;
		break;
	default:
		/* Don't override the io_gpio and io_port */
		break;
	}
}

static int bnx2x_8727_common_init_phy(struct bnx2x *bp,
				      u32 shmem_base_path[],
				      u32 shmem2_base_path[], u8 phy_index,
				      u32 chip_id)
{
	s8 port, reset_gpio;
	u32 swap_val, swap_override;
	struct bnx2x_phy phy[PORT_MAX];
	struct bnx2x_phy *phy_blk[PORT_MAX];
	s8 port_of_path;
	swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
	swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);

	reset_gpio = MISC_REGISTERS_GPIO_1;
	port = 1;

	/*
	 * Retrieve the reset gpio/port which control the reset.
	 * Default is GPIO1, PORT1
	 */
	bnx2x_get_ext_phy_reset_gpio(bp, shmem_base_path[0],
				     (u8 *)&reset_gpio, (u8 *)&port);

	/* Calculate the port based on port swap */
	port ^= (swap_val && swap_override);

	/* Initiate PHY reset*/
	bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_LOW,
		       port);
	msleep(1);
	bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_HIGH,
		       port);

	msleep(5);

	/* PART1 - Reset both phys */
	for (port = PORT_MAX - 1; port >= PORT_0; port--) {
		u32 shmem_base, shmem2_base;

		/* In E2, same phy is using for port0 of the two paths */
		if (CHIP_IS_E2(bp)) {
			shmem_base = shmem_base_path[port];
			shmem2_base = shmem2_base_path[port];
			port_of_path = 0;
		} else {
			shmem_base = shmem_base_path[0];
			shmem2_base = shmem2_base_path[0];
			port_of_path = port;
		}

		/* Extract the ext phy address for the port */
		if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
				       port_of_path, &phy[port]) !=
				       0) {
			DP(NETIF_MSG_LINK, "populate phy failed\n");
			return -EINVAL;
		}
		/* disable attentions */
		bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 +
			       port_of_path*4,
			       (NIG_MASK_XGXS0_LINK_STATUS |
				NIG_MASK_XGXS0_LINK10G |
				NIG_MASK_SERDES0_LINK_STATUS |
				NIG_MASK_MI_INT));


		/* Reset the phy */
		bnx2x_cl45_write(bp, &phy[port],
				 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15);
	}

	/* Add delay of 150ms after reset */
	msleep(150);
	if (phy[PORT_0].addr & 0x1) {
		phy_blk[PORT_0] = &(phy[PORT_1]);
		phy_blk[PORT_1] = &(phy[PORT_0]);
	} else {
		phy_blk[PORT_0] = &(phy[PORT_0]);
		phy_blk[PORT_1] = &(phy[PORT_1]);
	}
	/* PART2 - Download firmware to both phys */
	for (port = PORT_MAX - 1; port >= PORT_0; port--) {
		if (CHIP_IS_E2(bp))
			port_of_path = 0;
		else
			port_of_path = port;
		DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n",
			   phy_blk[port]->addr);
		if (bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port],
						      port_of_path))
			return -EINVAL;

	}
	return 0;
}

static int bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base_path[],
				     u32 shmem2_base_path[], u8 phy_index,
				     u32 ext_phy_type, u32 chip_id)
{
	int rc = 0;

	switch (ext_phy_type) {
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
		rc = bnx2x_8073_common_init_phy(bp, shmem_base_path,
						shmem2_base_path,
						phy_index, chip_id);
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC:
		rc = bnx2x_8727_common_init_phy(bp, shmem_base_path,
						shmem2_base_path,
						phy_index, chip_id);
		break;

	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
		/*
		 * GPIO1 affects both ports, so there's need to pull
		 * it for single port alone
		 */
		rc = bnx2x_8726_common_init_phy(bp, shmem_base_path,
						shmem2_base_path,
						phy_index, chip_id);
		break;
	case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
		rc = -EINVAL;
		break;
	default:
		DP(NETIF_MSG_LINK,
			   "ext_phy 0x%x common init not required\n",
			   ext_phy_type);
		break;
	}

	if (rc != 0)
		netdev_err(bp->dev,  "Warning: PHY was not initialized,"
				      " Port %d\n",
			 0);
	return rc;
}

int bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[],
			  u32 shmem2_base_path[], u32 chip_id)
{
	int rc = 0;
	u32 phy_ver;
	u8 phy_index;
	u32 ext_phy_type, ext_phy_config;
	DP(NETIF_MSG_LINK, "Begin common phy init\n");

	/* Check if common init was already done */
	phy_ver = REG_RD(bp, shmem_base_path[0] +
			 offsetof(struct shmem_region,
				  port_mb[PORT_0].ext_phy_fw_version));
	if (phy_ver) {
		DP(NETIF_MSG_LINK, "Not doing common init; phy ver is 0x%x\n",
			       phy_ver);
		return 0;
	}

	/* Read the ext_phy_type for arbitrary port(0) */
	for (phy_index = EXT_PHY1; phy_index < MAX_PHYS;
	      phy_index++) {
		ext_phy_config = bnx2x_get_ext_phy_config(bp,
							  shmem_base_path[0],
							  phy_index, 0);
		ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config);
		rc |= bnx2x_ext_phy_common_init(bp, shmem_base_path,
						shmem2_base_path,
						phy_index, ext_phy_type,
						chip_id);
	}
	return rc;
}

u8 bnx2x_hw_lock_required(struct bnx2x *bp, u32 shmem_base, u32 shmem2_base)
{
	u8 phy_index;
	struct bnx2x_phy phy;
	for (phy_index = INT_PHY; phy_index < MAX_PHYS;
	      phy_index++) {
		if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
				       0, &phy) != 0) {
			DP(NETIF_MSG_LINK, "populate phy failed\n");
			return 0;
		}

		if (phy.flags & FLAGS_HW_LOCK_REQUIRED)
			return 1;
	}
	return 0;
}

u8 bnx2x_fan_failure_det_req(struct bnx2x *bp,
			     u32 shmem_base,
			     u32 shmem2_base,
			     u8 port)
{
	u8 phy_index, fan_failure_det_req = 0;
	struct bnx2x_phy phy;
	for (phy_index = EXT_PHY1; phy_index < MAX_PHYS;
	      phy_index++) {
		if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
				       port, &phy)
		    != 0) {
			DP(NETIF_MSG_LINK, "populate phy failed\n");
			return 0;
		}
		fan_failure_det_req |= (phy.flags &
					FLAGS_FAN_FAILURE_DET_REQ);
	}
	return fan_failure_det_req;
}

void bnx2x_hw_reset_phy(struct link_params *params)
{
	u8 phy_index;
	for (phy_index = EXT_PHY1; phy_index < MAX_PHYS;
	      phy_index++) {
		if (params->phy[phy_index].hw_reset) {
			params->phy[phy_index].hw_reset(
				&params->phy[phy_index],
				params);
			params->phy[phy_index] = phy_null;
		}
	}
}