linux-vybrid_public/arch/powerpc/platforms/Kconfig

menu "Platform support"

source "arch/powerpc/platforms/powernv/Kconfig"
source "arch/powerpc/platforms/pseries/Kconfig"
source "arch/powerpc/platforms/chrp/Kconfig"
source "arch/powerpc/platforms/512x/Kconfig"
source "arch/powerpc/platforms/52xx/Kconfig"
source "arch/powerpc/platforms/powermac/Kconfig"
source "arch/powerpc/platforms/maple/Kconfig"
source "arch/powerpc/platforms/pasemi/Kconfig"
source "arch/powerpc/platforms/ps3/Kconfig"
source "arch/powerpc/platforms/cell/Kconfig"
source "arch/powerpc/platforms/8xx/Kconfig"
source "arch/powerpc/platforms/82xx/Kconfig"
source "arch/powerpc/platforms/83xx/Kconfig"
source "arch/powerpc/platforms/85xx/Kconfig"
source "arch/powerpc/platforms/86xx/Kconfig"
source "arch/powerpc/platforms/embedded6xx/Kconfig"
source "arch/powerpc/platforms/44x/Kconfig"
source "arch/powerpc/platforms/40x/Kconfig"
source "arch/powerpc/platforms/amigaone/Kconfig"
source "arch/powerpc/platforms/wsp/Kconfig"

config KVM_GUEST
	bool "KVM Guest support"
	default n
	select EPAPR_PARAVIRT
	---help---
	  This option enables various optimizations for running under the KVM
	  hypervisor. Overhead for the kernel when not running inside KVM should
	  be minimal.

	  In case of doubt, say Y

config EPAPR_PARAVIRT
	bool "ePAPR para-virtualization support"
	default n
	help
	  Enables ePAPR para-virtualization support for guests.

	  In case of doubt, say Y

config PPC_NATIVE
	bool
	depends on 6xx || PPC64
	help
	  Support for running natively on the hardware, i.e. without
	  a hypervisor. This option is not user-selectable but should
	  be selected by all platforms that need it.

config PPC_OF_BOOT_TRAMPOLINE
	bool "Support booting from Open Firmware or yaboot"
	depends on 6xx || PPC64
	default y
	help
	  Support from booting from Open Firmware or yaboot using an
	  Open Firmware client interface. This enables the kernel to
	  communicate with open firmware to retrieve system information
	  such as the device tree.

	  In case of doubt, say Y

config UDBG_RTAS_CONSOLE
	bool "RTAS based debug console"
	depends on PPC_RTAS
	default n

config PPC_SMP_MUXED_IPI
	bool
	help
	  Select this opton if your platform supports SMP and your
	  interrupt controller provides less than 4 interrupts to each
	  cpu.	This will enable the generic code to multiplex the 4
	  messages on to one ipi.

config PPC_UDBG_BEAT
	bool "BEAT based debug console"
	depends on PPC_CELLEB
	default n

config IPIC
	bool
	default n

config MPIC
	bool
	default n

config PPC_EPAPR_HV_PIC
	bool
	default n
	select EPAPR_PARAVIRT

config MPIC_WEIRD
	bool
	default n

config MPIC_MSGR
	bool "MPIC message register support"
	depends on MPIC
	default n
	help
	  Enables support for the MPIC message registers.  These
	  registers are used for inter-processor communication.

config PPC_I8259
	bool
	default n

config U3_DART
	bool
	depends on PPC64
	default n

config PPC_RTAS
	bool
	default n

config RTAS_ERROR_LOGGING
	bool
	depends on PPC_RTAS
	default n

config PPC_RTAS_DAEMON
	bool
	depends on PPC_RTAS
	default n

config RTAS_PROC
	bool "Proc interface to RTAS"
	depends on PPC_RTAS && PROC_FS
	default y

config RTAS_FLASH
	tristate "Firmware flash interface"
	depends on PPC64 && RTAS_PROC

config MMIO_NVRAM
	bool
	default n

config MPIC_U3_HT_IRQS
	bool
	default n

config MPIC_BROKEN_REGREAD
	bool
	depends on MPIC
	help
	  This option enables a MPIC driver workaround for some chips
	  that have a bug that causes some interrupt source information
	  to not read back properly. It is safe to use on other chips as
	  well, but enabling it uses about 8KB of memory to keep copies
	  of the register contents in software.

config IBMVIO
	depends on PPC_PSERIES
	bool
	default y

config IBMEBUS
	depends on PPC_PSERIES
	bool "Support for GX bus based adapters"
	help
	  Bus device driver for GX bus based adapters.

config PPC_MPC106
	bool
	default n

config PPC_970_NAP
	bool
	default n

config PPC_P7_NAP
	bool
	default n

config PPC_INDIRECT_IO
	bool
	select GENERIC_IOMAP

config PPC_INDIRECT_PIO
	bool
	select PPC_INDIRECT_IO

config PPC_INDIRECT_MMIO
	bool
	select PPC_INDIRECT_IO

config PPC_IO_WORKAROUNDS
	bool

source "drivers/cpufreq/Kconfig"

menu "CPUIdle driver"

source "drivers/cpuidle/Kconfig"

endmenu

config PPC601_SYNC_FIX
	bool "Workarounds for PPC601 bugs"
	depends on 6xx && PPC_PMAC
	help
	  Some versions of the PPC601 (the first PowerPC chip) have bugs which
	  mean that extra synchronization instructions are required near
	  certain instructions, typically those that make major changes to the
	  CPU state.  These extra instructions reduce performance slightly.
	  If you say N here, these extra instructions will not be included,
	  resulting in a kernel which will run faster but may not run at all
	  on some systems with the PPC601 chip.

	  If in doubt, say Y here.

config TAU
	bool "On-chip CPU temperature sensor support"
	depends on 6xx
	help
	  G3 and G4 processors have an on-chip temperature sensor called the
	  'Thermal Assist Unit (TAU)', which, in theory, can measure the on-die
	  temperature within 2-4 degrees Celsius. This option shows the current
	  on-die temperature in /proc/cpuinfo if the cpu supports it.

	  Unfortunately, on some chip revisions, this sensor is very inaccurate
	  and in many cases, does not work at all, so don't assume the cpu
	  temp is actually what /proc/cpuinfo says it is.

config TAU_INT
	bool "Interrupt driven TAU driver (DANGEROUS)"
	depends on TAU
	---help---
	  The TAU supports an interrupt driven mode which causes an interrupt
	  whenever the temperature goes out of range. This is the fastest way
	  to get notified the temp has exceeded a range. With this option off,
	  a timer is used to re-check the temperature periodically.

	  However, on some cpus it appears that the TAU interrupt hardware
	  is buggy and can cause a situation which would lead unexplained hard
	  lockups.

	  Unless you are extending the TAU driver, or enjoy kernel/hardware
	  debugging, leave this option off.

config TAU_AVERAGE
	bool "Average high and low temp"
	depends on TAU
	---help---
	  The TAU hardware can compare the temperature to an upper and lower
	  bound.  The default behavior is to show both the upper and lower
	  bound in /proc/cpuinfo. If the range is large, the temperature is
	  either changing a lot, or the TAU hardware is broken (likely on some
	  G4's). If the range is small (around 4 degrees), the temperature is
	  relatively stable.  If you say Y here, a single temperature value,
	  halfway between the upper and lower bounds, will be reported in
	  /proc/cpuinfo.

	  If in doubt, say N here.

config QUICC_ENGINE
	bool "Freescale QUICC Engine (QE) Support"
	depends on FSL_SOC && PPC32
	select PPC_LIB_RHEAP
	select CRC32
	help
	  The QUICC Engine (QE) is a new generation of communications
	  coprocessors on Freescale embedded CPUs (akin to CPM in older chips).
	  Selecting this option means that you wish to build a kernel
	  for a machine with a QE coprocessor.

config QE_GPIO
	bool "QE GPIO support"
	depends on QUICC_ENGINE
	select ARCH_REQUIRE_GPIOLIB
	help
	  Say Y here if you're going to use hardware that connects to the
	  QE GPIOs.

config CPM2
	bool "Enable support for the CPM2 (Communications Processor Module)"
	depends on (FSL_SOC_BOOKE && PPC32) || 8260
	select CPM
	select PPC_LIB_RHEAP
	select PPC_PCI_CHOICE
	select ARCH_REQUIRE_GPIOLIB
	help
	  The CPM2 (Communications Processor Module) is a coprocessor on
	  embedded CPUs made by Freescale.  Selecting this option means that
	  you wish to build a kernel for a machine with a CPM2 coprocessor
	  on it (826x, 827x, 8560).

config AXON_RAM
	tristate "Axon DDR2 memory device driver"
	depends on PPC_IBM_CELL_BLADE && BLOCK
	default m
	help
	  It registers one block device per Axon's DDR2 memory bank found
	  on a system. Block devices are called axonram?, their major and
	  minor numbers are available in /proc/devices, /proc/partitions or
	  in /sys/block/axonram?/dev.

config FSL_ULI1575
	bool
	default n
	select GENERIC_ISA_DMA
	help
	  Supports for the ULI1575 PCIe south bridge that exists on some
	  Freescale reference boards. The boards all use the ULI in pretty
	  much the same way.

config CPM
	bool

config OF_RTC
	bool
	help
	  Uses information from the OF or flattened device tree to instantiate
	  platform devices for direct mapped RTC chips like the DS1742 or DS1743.

config SIMPLE_GPIO
	bool "Support for simple, memory-mapped GPIO controllers"
	depends on PPC
	select ARCH_REQUIRE_GPIOLIB
	help
	  Say Y here to support simple, memory-mapped GPIO controllers.
	  These are usually BCSRs used to control board's switches, LEDs,
	  chip-selects, Ethernet/USB PHY's power and various other small
	  on-board peripherals.

config MCU_MPC8349EMITX
	bool "MPC8349E-mITX MCU driver"
	depends on I2C=y && PPC_83xx
	select ARCH_REQUIRE_GPIOLIB
	help
	  Say Y here to enable soft power-off functionality on the Freescale
	  boards with the MPC8349E-mITX-compatible MCU chips. This driver will
	  also register MCU GPIOs with the generic GPIO API, so you'll able
	  to use MCU pins as GPIOs.

config XILINX_PCI
	bool "Xilinx PCI host bridge support"
	depends on PCI && XILINX_VIRTEX

endmenu