linux-vybrid_public/include/linux/ide.h

#ifndef _IDE_H
#define _IDE_H
/*
 *  linux/include/linux/ide.h
 *
 *  Copyright (C) 1994-2002  Linus Torvalds & authors
 */

#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/hdreg.h>
#include <linux/blkdev.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/bitops.h>
#include <linux/bio.h>
#include <linux/device.h>
#include <linux/pci.h>
#include <linux/completion.h>
#ifdef CONFIG_BLK_DEV_IDEACPI
#include <acpi/acpi.h>
#endif
#include <asm/byteorder.h>
#include <asm/system.h>
#include <asm/io.h>
#include <asm/mutex.h>

#if defined(CONFIG_CRIS) || defined(CONFIG_FRV)
# define SUPPORT_VLB_SYNC 0
#else
# define SUPPORT_VLB_SYNC 1
#endif

/*
 * Used to indicate "no IRQ", should be a value that cannot be an IRQ
 * number.
 */
 
#define IDE_NO_IRQ		(-1)

typedef unsigned char	byte;	/* used everywhere */

/*
 * Probably not wise to fiddle with these
 */
#define ERROR_MAX	8	/* Max read/write errors per sector */
#define ERROR_RESET	3	/* Reset controller every 4th retry */
#define ERROR_RECAL	1	/* Recalibrate every 2nd retry */

/*
 * Tune flags
 */
#define IDE_TUNE_NOAUTO		2
#define IDE_TUNE_AUTO		1
#define IDE_TUNE_DEFAULT	0

/*
 * state flags
 */

#define DMA_PIO_RETRY	1	/* retrying in PIO */

#define HWIF(drive)		((ide_hwif_t *)((drive)->hwif))
#define HWGROUP(drive)		((ide_hwgroup_t *)(HWIF(drive)->hwgroup))

/*
 * Definitions for accessing IDE controller registers
 */
#define IDE_NR_PORTS		(10)

#define IDE_DATA_OFFSET		(0)
#define IDE_ERROR_OFFSET	(1)
#define IDE_NSECTOR_OFFSET	(2)
#define IDE_SECTOR_OFFSET	(3)
#define IDE_LCYL_OFFSET		(4)
#define IDE_HCYL_OFFSET		(5)
#define IDE_SELECT_OFFSET	(6)
#define IDE_STATUS_OFFSET	(7)
#define IDE_CONTROL_OFFSET	(8)
#define IDE_IRQ_OFFSET		(9)

#define IDE_FEATURE_OFFSET	IDE_ERROR_OFFSET
#define IDE_COMMAND_OFFSET	IDE_STATUS_OFFSET
#define IDE_ALTSTATUS_OFFSET	IDE_CONTROL_OFFSET
#define IDE_IREASON_OFFSET	IDE_NSECTOR_OFFSET
#define IDE_BCOUNTL_OFFSET	IDE_LCYL_OFFSET
#define IDE_BCOUNTH_OFFSET	IDE_HCYL_OFFSET

#define OK_STAT(stat,good,bad)	(((stat)&((good)|(bad)))==(good))
#define BAD_R_STAT		(BUSY_STAT   | ERR_STAT)
#define BAD_W_STAT		(BAD_R_STAT  | WRERR_STAT)
#define BAD_STAT		(BAD_R_STAT  | DRQ_STAT)
#define DRIVE_READY		(READY_STAT  | SEEK_STAT)

#define BAD_CRC			(ABRT_ERR    | ICRC_ERR)

#define SATA_NR_PORTS		(3)	/* 16 possible ?? */

#define SATA_STATUS_OFFSET	(0)
#define SATA_ERROR_OFFSET	(1)
#define SATA_CONTROL_OFFSET	(2)

/*
 * Our Physical Region Descriptor (PRD) table should be large enough
 * to handle the biggest I/O request we are likely to see.  Since requests
 * can have no more than 256 sectors, and since the typical blocksize is
 * two or more sectors, we could get by with a limit of 128 entries here for
 * the usual worst case.  Most requests seem to include some contiguous blocks,
 * further reducing the number of table entries required.
 *
 * The driver reverts to PIO mode for individual requests that exceed
 * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
 * 100% of all crazy scenarios here is not necessary.
 *
 * As it turns out though, we must allocate a full 4KB page for this,
 * so the two PRD tables (ide0 & ide1) will each get half of that,
 * allowing each to have about 256 entries (8 bytes each) from this.
 */
#define PRD_BYTES       8
#define PRD_ENTRIES	256

/*
 * Some more useful definitions
 */
#define PARTN_BITS	6	/* number of minor dev bits for partitions */
#define MAX_DRIVES	2	/* per interface; 2 assumed by lots of code */
#define SECTOR_SIZE	512
#define SECTOR_WORDS	(SECTOR_SIZE / 4)	/* number of 32bit words per sector */
#define IDE_LARGE_SEEK(b1,b2,t)	(((b1) > (b2) + (t)) || ((b2) > (b1) + (t)))

/*
 * Timeouts for various operations:
 */
#define WAIT_DRQ	(HZ/10)		/* 100msec - spec allows up to 20ms */
#define WAIT_READY	(5*HZ)		/* 5sec - some laptops are very slow */
#define WAIT_PIDENTIFY	(10*HZ)	/* 10sec  - should be less than 3ms (?), if all ATAPI CD is closed at boot */
#define WAIT_WORSTCASE	(30*HZ)	/* 30sec  - worst case when spinning up */
#define WAIT_CMD	(10*HZ)	/* 10sec  - maximum wait for an IRQ to happen */
#define WAIT_MIN_SLEEP	(2*HZ/100)	/* 20msec - minimum sleep time */

/*
 * Check for an interrupt and acknowledge the interrupt status
 */
struct hwif_s;
typedef int (ide_ack_intr_t)(struct hwif_s *);

/*
 * hwif_chipset_t is used to keep track of the specific hardware
 * chipset used by each IDE interface, if known.
 */
enum {		ide_unknown,	ide_generic,	ide_pci,
		ide_cmd640,	ide_dtc2278,	ide_ali14xx,
		ide_qd65xx,	ide_umc8672,	ide_ht6560b,
		ide_rz1000,	ide_trm290,
		ide_cmd646,	ide_cy82c693,	ide_4drives,
		ide_pmac,	ide_etrax100,	ide_acorn,
		ide_au1xxx,	ide_palm3710
};

typedef u8 hwif_chipset_t;

/*
 * Structure to hold all information about the location of this port
 */
typedef struct hw_regs_s {
	unsigned long	io_ports[IDE_NR_PORTS];	/* task file registers */
	int		irq;			/* our irq number */
	ide_ack_intr_t	*ack_intr;		/* acknowledge interrupt */
	hwif_chipset_t  chipset;
	struct device	*dev;
} hw_regs_t;

void ide_init_port_data(struct hwif_s *, unsigned int);
void ide_init_port_hw(struct hwif_s *, hw_regs_t *);

static inline void ide_std_init_ports(hw_regs_t *hw,
				      unsigned long io_addr,
				      unsigned long ctl_addr)
{
	unsigned int i;

	for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
		hw->io_ports[i] = io_addr++;

	hw->io_ports[IDE_CONTROL_OFFSET] = ctl_addr;
}

#include <asm/ide.h>

#if !defined(MAX_HWIFS) || defined(CONFIG_EMBEDDED)
#undef MAX_HWIFS
#define MAX_HWIFS	CONFIG_IDE_MAX_HWIFS
#endif

/* Currently only m68k, apus and m8xx need it */
#ifndef IDE_ARCH_ACK_INTR
# define ide_ack_intr(hwif) (1)
#endif

/* Currently only Atari needs it */
#ifndef IDE_ARCH_LOCK
# define ide_release_lock()			do {} while (0)
# define ide_get_lock(hdlr, data)		do {} while (0)
#endif /* IDE_ARCH_LOCK */

/*
 * Now for the data we need to maintain per-drive:  ide_drive_t
 */

#define ide_scsi	0x21
#define ide_disk	0x20
#define ide_optical	0x7
#define ide_cdrom	0x5
#define ide_tape	0x1
#define ide_floppy	0x0

/*
 * Special Driver Flags
 *
 * set_geometry	: respecify drive geometry
 * recalibrate	: seek to cyl 0
 * set_multmode	: set multmode count
 * set_tune	: tune interface for drive
 * serviced	: service command
 * reserved	: unused
 */
typedef union {
	unsigned all			: 8;
	struct {
		unsigned set_geometry	: 1;
		unsigned recalibrate	: 1;
		unsigned set_multmode	: 1;
		unsigned set_tune	: 1;
		unsigned serviced	: 1;
		unsigned reserved	: 3;
	} b;
} special_t;

/*
 * ATA-IDE Select Register, aka Device-Head
 *
 * head		: always zeros here
 * unit		: drive select number: 0/1
 * bit5		: always 1
 * lba		: using LBA instead of CHS
 * bit7		: always 1
 */
typedef union {
	unsigned all			: 8;
	struct {
#if defined(__LITTLE_ENDIAN_BITFIELD)
		unsigned head		: 4;
		unsigned unit		: 1;
		unsigned bit5		: 1;
		unsigned lba		: 1;
		unsigned bit7		: 1;
#elif defined(__BIG_ENDIAN_BITFIELD)
		unsigned bit7		: 1;
		unsigned lba		: 1;
		unsigned bit5		: 1;
		unsigned unit		: 1;
		unsigned head		: 4;
#else
#error "Please fix <asm/byteorder.h>"
#endif
	} b;
} select_t, ata_select_t;

/*
 * Status returned from various ide_ functions
 */
typedef enum {
	ide_stopped,	/* no drive operation was started */
	ide_started,	/* a drive operation was started, handler was set */
} ide_startstop_t;

struct ide_driver_s;
struct ide_settings_s;

#ifdef CONFIG_BLK_DEV_IDEACPI
struct ide_acpi_drive_link;
struct ide_acpi_hwif_link;
#endif

typedef struct ide_drive_s {
	char		name[4];	/* drive name, such as "hda" */
        char            driver_req[10];	/* requests specific driver */

	struct request_queue	*queue;	/* request queue */

	struct request		*rq;	/* current request */
	struct ide_drive_s 	*next;	/* circular list of hwgroup drives */
	void		*driver_data;	/* extra driver data */
	struct hd_driveid	*id;	/* drive model identification info */
#ifdef CONFIG_IDE_PROC_FS
	struct proc_dir_entry *proc;	/* /proc/ide/ directory entry */
	struct ide_settings_s *settings;/* /proc/ide/ drive settings */
#endif
	struct hwif_s		*hwif;	/* actually (ide_hwif_t *) */

	unsigned long sleep;		/* sleep until this time */
	unsigned long service_start;	/* time we started last request */
	unsigned long service_time;	/* service time of last request */
	unsigned long timeout;		/* max time to wait for irq */

	special_t	special;	/* special action flags */
	select_t	select;		/* basic drive/head select reg value */

	u8	keep_settings;		/* restore settings after drive reset */
	u8	using_dma;		/* disk is using dma for read/write */
	u8	retry_pio;		/* retrying dma capable host in pio */
	u8	state;			/* retry state */
	u8	waiting_for_dma;	/* dma currently in progress */
	u8	unmask;			/* okay to unmask other irqs */
	u8	noflush;		/* don't attempt flushes */
	u8	dsc_overlap;		/* DSC overlap */
	u8	nice1;			/* give potential excess bandwidth */

	unsigned present	: 1;	/* drive is physically present */
	unsigned dead		: 1;	/* device ejected hint */
	unsigned id_read	: 1;	/* 1=id read from disk 0 = synthetic */
	unsigned noprobe 	: 1;	/* from:  hdx=noprobe */
	unsigned removable	: 1;	/* 1 if need to do check_media_change */
	unsigned attach		: 1;	/* needed for removable devices */
	unsigned forced_geom	: 1;	/* 1 if hdx=c,h,s was given at boot */
	unsigned no_unmask	: 1;	/* disallow setting unmask bit */
	unsigned no_io_32bit	: 1;	/* disallow enabling 32bit I/O */
	unsigned atapi_overlap	: 1;	/* ATAPI overlap (not supported) */
	unsigned doorlocking	: 1;	/* for removable only: door lock/unlock works */
	unsigned nodma		: 1;	/* disallow DMA */
	unsigned autotune	: 2;	/* 0=default, 1=autotune, 2=noautotune */
	unsigned remap_0_to_1	: 1;	/* 0=noremap, 1=remap 0->1 (for EZDrive) */
	unsigned blocked        : 1;	/* 1=powermanagment told us not to do anything, so sleep nicely */
	unsigned vdma		: 1;	/* 1=doing PIO over DMA 0=doing normal DMA */
	unsigned scsi		: 1;	/* 0=default, 1=ide-scsi emulation */
	unsigned sleeping	: 1;	/* 1=sleeping & sleep field valid */
	unsigned post_reset	: 1;
	unsigned udma33_warned	: 1;

	u8	addressing;	/* 0=28-bit, 1=48-bit, 2=48-bit doing 28-bit */
        u8	quirk_list;	/* considered quirky, set for a specific host */
        u8	init_speed;	/* transfer rate set at boot */
        u8	current_speed;	/* current transfer rate set */
	u8	desired_speed;	/* desired transfer rate set */
        u8	dn;		/* now wide spread use */
        u8	wcache;		/* status of write cache */
	u8	acoustic;	/* acoustic management */
	u8	media;		/* disk, cdrom, tape, floppy, ... */
	u8	ctl;		/* "normal" value for Control register */
	u8	ready_stat;	/* min status value for drive ready */
	u8	mult_count;	/* current multiple sector setting */
	u8	mult_req;	/* requested multiple sector setting */
	u8	tune_req;	/* requested drive tuning setting */
	u8	io_32bit;	/* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
	u8	bad_wstat;	/* used for ignoring WRERR_STAT */
	u8	nowerr;		/* used for ignoring WRERR_STAT */
	u8	sect0;		/* offset of first sector for DM6:DDO */
	u8	head;		/* "real" number of heads */
	u8	sect;		/* "real" sectors per track */
	u8	bios_head;	/* BIOS/fdisk/LILO number of heads */
	u8	bios_sect;	/* BIOS/fdisk/LILO sectors per track */

	unsigned int	bios_cyl;	/* BIOS/fdisk/LILO number of cyls */
	unsigned int	cyl;		/* "real" number of cyls */
	unsigned int	drive_data;	/* used by set_pio_mode/selectproc */
	unsigned int	failures;	/* current failure count */
	unsigned int	max_failures;	/* maximum allowed failure count */
	u64		probed_capacity;/* initial reported media capacity (ide-cd only currently) */

	u64		capacity64;	/* total number of sectors */

	int		lun;		/* logical unit */
	int		crc_count;	/* crc counter to reduce drive speed */
#ifdef CONFIG_BLK_DEV_IDEACPI
	struct ide_acpi_drive_link *acpidata;
#endif
	struct list_head list;
	struct device	gendev;
	struct completion gendev_rel_comp;	/* to deal with device release() */
} ide_drive_t;

#define to_ide_device(dev)container_of(dev, ide_drive_t, gendev)

#define IDE_CHIPSET_PCI_MASK	\
    ((1<<ide_pci)|(1<<ide_cmd646)|(1<<ide_ali14xx))
#define IDE_CHIPSET_IS_PCI(c)	((IDE_CHIPSET_PCI_MASK >> (c)) & 1)

struct ide_port_info;

struct ide_port_ops {
	/* host specific initialization of devices on a port */
	void	(*port_init_devs)(struct hwif_s *);
	/* routine to program host for PIO mode */
	void	(*set_pio_mode)(ide_drive_t *, const u8);
	/* routine to program host for DMA mode */
	void	(*set_dma_mode)(ide_drive_t *, const u8);
	/* tweaks hardware to select drive */
	void	(*selectproc)(ide_drive_t *);
	/* chipset polling based on hba specifics */
	int	(*reset_poll)(ide_drive_t *);
	/* chipset specific changes to default for device-hba resets */
	void	(*pre_reset)(ide_drive_t *);
	/* routine to reset controller after a disk reset */
	void	(*resetproc)(ide_drive_t *);
	/* special host masking for drive selection */
	void	(*maskproc)(ide_drive_t *, int);
	/* check host's drive quirk list */
	void	(*quirkproc)(ide_drive_t *);

	u8	(*mdma_filter)(ide_drive_t *);
	u8	(*udma_filter)(ide_drive_t *);

	u8	(*cable_detect)(struct hwif_s *);
};

typedef struct hwif_s {
	struct hwif_s *next;		/* for linked-list in ide_hwgroup_t */
	struct hwif_s *mate;		/* other hwif from same PCI chip */
	struct hwgroup_s *hwgroup;	/* actually (ide_hwgroup_t *) */
	struct proc_dir_entry *proc;	/* /proc/ide/ directory entry */

	char name[6];			/* name of interface, eg. "ide0" */

		/* task file registers for pata and sata */
	unsigned long	io_ports[IDE_NR_PORTS];
	unsigned long	sata_scr[SATA_NR_PORTS];

	ide_drive_t	drives[MAX_DRIVES];	/* drive info */

	u8 major;	/* our major number */
	u8 index;	/* 0 for ide0; 1 for ide1; ... */
	u8 channel;	/* for dual-port chips: 0=primary, 1=secondary */
	u8 bus_state;	/* power state of the IDE bus */

	u32 host_flags;

	u8 pio_mask;

	u8 ultra_mask;
	u8 mwdma_mask;
	u8 swdma_mask;

	u8 cbl;		/* cable type */

	hwif_chipset_t chipset;	/* sub-module for tuning.. */

	struct device *dev;

	ide_ack_intr_t *ack_intr;

	void (*rw_disk)(ide_drive_t *, struct request *);

	const struct ide_port_ops	*port_ops;

	void (*ata_input_data)(ide_drive_t *, void *, u32);
	void (*ata_output_data)(ide_drive_t *, void *, u32);

	void (*atapi_input_bytes)(ide_drive_t *, void *, u32);
	void (*atapi_output_bytes)(ide_drive_t *, void *, u32);

	void (*dma_host_set)(ide_drive_t *, int);
	int (*dma_setup)(ide_drive_t *);
	void (*dma_exec_cmd)(ide_drive_t *, u8);
	void (*dma_start)(ide_drive_t *);
	int (*ide_dma_end)(ide_drive_t *drive);
	int (*ide_dma_test_irq)(ide_drive_t *drive);
	void (*ide_dma_clear_irq)(ide_drive_t *drive);
	void (*dma_lost_irq)(ide_drive_t *drive);
	void (*dma_timeout)(ide_drive_t *drive);

	void (*OUTB)(u8 addr, unsigned long port);
	void (*OUTBSYNC)(ide_drive_t *drive, u8 addr, unsigned long port);
	void (*OUTW)(u16 addr, unsigned long port);
	void (*OUTSW)(unsigned long port, void *addr, u32 count);
	void (*OUTSL)(unsigned long port, void *addr, u32 count);

	u8  (*INB)(unsigned long port);
	u16 (*INW)(unsigned long port);
	void (*INSW)(unsigned long port, void *addr, u32 count);
	void (*INSL)(unsigned long port, void *addr, u32 count);

	/* dma physical region descriptor table (cpu view) */
	unsigned int	*dmatable_cpu;
	/* dma physical region descriptor table (dma view) */
	dma_addr_t	dmatable_dma;
	/* Scatter-gather list used to build the above */
	struct scatterlist *sg_table;
	int sg_max_nents;		/* Maximum number of entries in it */
	int sg_nents;			/* Current number of entries in it */
	int sg_dma_direction;		/* dma transfer direction */

	/* data phase of the active command (currently only valid for PIO/DMA) */
	int		data_phase;

	unsigned int nsect;
	unsigned int nleft;
	struct scatterlist *cursg;
	unsigned int cursg_ofs;

	int		rqsize;		/* max sectors per request */
	int		irq;		/* our irq number */

	unsigned long	dma_base;	/* base addr for dma ports */
	unsigned long	dma_command;	/* dma command register */
	unsigned long	dma_vendor1;	/* dma vendor 1 register */
	unsigned long	dma_status;	/* dma status register */
	unsigned long	dma_vendor3;	/* dma vendor 3 register */
	unsigned long	dma_prdtable;	/* actual prd table address */

	unsigned long	config_data;	/* for use by chipset-specific code */
	unsigned long	select_data;	/* for use by chipset-specific code */

	unsigned long	extra_base;	/* extra addr for dma ports */
	unsigned	extra_ports;	/* number of extra dma ports */

	unsigned	present    : 1;	/* this interface exists */
	unsigned	serialized : 1;	/* serialized all channel operation */
	unsigned	sharing_irq: 1;	/* 1 = sharing irq with another hwif */
	unsigned	reset      : 1;	/* reset after probe */
	unsigned	sg_mapped  : 1;	/* sg_table and sg_nents are ready */
	unsigned	mmio       : 1; /* host uses MMIO */

	struct device		gendev;
	struct device		*portdev;

	struct completion gendev_rel_comp; /* To deal with device release() */

	void		*hwif_data;	/* extra hwif data */

	unsigned dma;

#ifdef CONFIG_BLK_DEV_IDEACPI
	struct ide_acpi_hwif_link *acpidata;
#endif
} ____cacheline_internodealigned_in_smp ide_hwif_t;

/*
 *  internal ide interrupt handler type
 */
typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
typedef int (ide_expiry_t)(ide_drive_t *);

/* used by ide-cd, ide-floppy, etc. */
typedef void (xfer_func_t)(ide_drive_t *, void *, u32);

typedef struct hwgroup_s {
		/* irq handler, if active */
	ide_startstop_t	(*handler)(ide_drive_t *);

		/* BOOL: protects all fields below */
	volatile int busy;
		/* BOOL: wake us up on timer expiry */
	unsigned int sleeping	: 1;
		/* BOOL: polling active & poll_timeout field valid */
	unsigned int polling	: 1;
	 	/* BOOL: in a polling reset situation. Must not trigger another reset yet */
	unsigned int resetting  : 1;

		/* current drive */
	ide_drive_t *drive;
		/* ptr to current hwif in linked-list */
	ide_hwif_t *hwif;

		/* current request */
	struct request *rq;

		/* failsafe timer */
	struct timer_list timer;
		/* timeout value during long polls */
	unsigned long poll_timeout;
		/* queried upon timeouts */
	int (*expiry)(ide_drive_t *);

	int req_gen;
	int req_gen_timer;
} ide_hwgroup_t;

typedef struct ide_driver_s ide_driver_t;

extern struct mutex ide_setting_mtx;

int set_io_32bit(ide_drive_t *, int);
int set_pio_mode(ide_drive_t *, int);
int set_using_dma(ide_drive_t *, int);

/* ATAPI packet command flags */
enum {
	/* set when an error is considered normal - no retry (ide-tape) */
	PC_FLAG_ABORT			= (1 << 0),
	PC_FLAG_SUPPRESS_ERROR		= (1 << 1),
	PC_FLAG_WAIT_FOR_DSC		= (1 << 2),
	PC_FLAG_DMA_OK			= (1 << 3),
	PC_FLAG_DMA_RECOMMENDED		= (1 << 4),
	PC_FLAG_DMA_IN_PROGRESS		= (1 << 5),
	PC_FLAG_DMA_ERROR		= (1 << 6),
	PC_FLAG_WRITING			= (1 << 7),
	/* command timed out */
	PC_FLAG_TIMEDOUT		= (1 << 8),
};

struct ide_atapi_pc {
	/* actual packet bytes */
	u8 c[12];
	/* incremented on each retry */
	int retries;
	int error;

	/* bytes to transfer */
	int req_xfer;
	/* bytes actually transferred */
	int xferred;

	/* data buffer */
	u8 *buf;
	/* current buffer position */
	u8 *cur_pos;
	int buf_size;
	/* missing/available data on the current buffer */
	int b_count;

	/* the corresponding request */
	struct request *rq;

	unsigned long flags;

	/*
	 * those are more or less driver-specific and some of them are subject
	 * to change/removal later.
	 */
	u8 pc_buf[256];
	void (*idefloppy_callback) (ide_drive_t *);
	ide_startstop_t (*idetape_callback) (ide_drive_t *);

	/* idetape only */
	struct idetape_bh *bh;
	char *b_data;

	/* idescsi only for now */
	struct scatterlist *sg;
	unsigned int sg_cnt;

	struct scsi_cmnd *scsi_cmd;
	void (*done) (struct scsi_cmnd *);

	unsigned long timeout;
};

#ifdef CONFIG_IDE_PROC_FS
/*
 * configurable drive settings
 */

#define TYPE_INT	0
#define TYPE_BYTE	1
#define TYPE_SHORT	2

#define SETTING_READ	(1 << 0)
#define SETTING_WRITE	(1 << 1)
#define SETTING_RW	(SETTING_READ | SETTING_WRITE)

typedef int (ide_procset_t)(ide_drive_t *, int);
typedef struct ide_settings_s {
	char			*name;
	int			rw;
	int			data_type;
	int			min;
	int			max;
	int			mul_factor;
	int			div_factor;
	void			*data;
	ide_procset_t		*set;
	int			auto_remove;
	struct ide_settings_s	*next;
} ide_settings_t;

int ide_add_setting(ide_drive_t *, const char *, int, int, int, int, int, int, void *, ide_procset_t *set);

/*
 * /proc/ide interface
 */
typedef struct {
	const char	*name;
	mode_t		mode;
	read_proc_t	*read_proc;
	write_proc_t	*write_proc;
} ide_proc_entry_t;

void proc_ide_create(void);
void proc_ide_destroy(void);
void ide_proc_register_port(ide_hwif_t *);
void ide_proc_port_register_devices(ide_hwif_t *);
void ide_proc_unregister_device(ide_drive_t *);
void ide_proc_unregister_port(ide_hwif_t *);
void ide_proc_register_driver(ide_drive_t *, ide_driver_t *);
void ide_proc_unregister_driver(ide_drive_t *, ide_driver_t *);

void ide_add_generic_settings(ide_drive_t *);

read_proc_t proc_ide_read_capacity;
read_proc_t proc_ide_read_geometry;

#ifdef CONFIG_BLK_DEV_IDEPCI
void ide_pci_create_host_proc(const char *, get_info_t *);
#endif

/*
 * Standard exit stuff:
 */
#define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
{					\
	len -= off;			\
	if (len < count) {		\
		*eof = 1;		\
		if (len <= 0)		\
			return 0;	\
	} else				\
		len = count;		\
	*start = page + off;		\
	return len;			\
}
#else
static inline void proc_ide_create(void) { ; }
static inline void proc_ide_destroy(void) { ; }
static inline void ide_proc_register_port(ide_hwif_t *hwif) { ; }
static inline void ide_proc_port_register_devices(ide_hwif_t *hwif) { ; }
static inline void ide_proc_unregister_device(ide_drive_t *drive) { ; }
static inline void ide_proc_unregister_port(ide_hwif_t *hwif) { ; }
static inline void ide_proc_register_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
static inline void ide_proc_unregister_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
static inline void ide_add_generic_settings(ide_drive_t *drive) { ; }
#define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
#endif

/*
 * Power Management step value (rq->pm->pm_step).
 *
 * The step value starts at 0 (ide_pm_state_start_suspend) for a
 * suspend operation or 1000 (ide_pm_state_start_resume) for a
 * resume operation.
 *
 * For each step, the core calls the subdriver start_power_step() first.
 * This can return:
 *	- ide_stopped :	In this case, the core calls us back again unless
 *			step have been set to ide_power_state_completed.
 *	- ide_started :	In this case, the channel is left busy until an
 *			async event (interrupt) occurs.
 * Typically, start_power_step() will issue a taskfile request with
 * do_rw_taskfile().
 *
 * Upon reception of the interrupt, the core will call complete_power_step()
 * with the error code if any. This routine should update the step value
 * and return. It should not start a new request. The core will call
 * start_power_step for the new step value, unless step have been set to
 * ide_power_state_completed.
 *
 * Subdrivers are expected to define their own additional power
 * steps from 1..999 for suspend and from 1001..1999 for resume,
 * other values are reserved for future use.
 */

enum {
	ide_pm_state_completed		= -1,
	ide_pm_state_start_suspend	= 0,
	ide_pm_state_start_resume	= 1000,
};

/*
 * Subdrivers support.
 *
 * The gendriver.owner field should be set to the module owner of this driver.
 * The gendriver.name field should be set to the name of this driver
 */
struct ide_driver_s {
	const char			*version;
	u8				media;
	unsigned supports_dsc_overlap	: 1;
	ide_startstop_t	(*do_request)(ide_drive_t *, struct request *, sector_t);
	int		(*end_request)(ide_drive_t *, int, int);
	ide_startstop_t	(*error)(ide_drive_t *, struct request *rq, u8, u8);
	ide_startstop_t	(*abort)(ide_drive_t *, struct request *rq);
	struct device_driver	gen_driver;
	int		(*probe)(ide_drive_t *);
	void		(*remove)(ide_drive_t *);
	void		(*resume)(ide_drive_t *);
	void		(*shutdown)(ide_drive_t *);
#ifdef CONFIG_IDE_PROC_FS
	ide_proc_entry_t	*proc;
#endif
};

#define to_ide_driver(drv) container_of(drv, ide_driver_t, gen_driver)

int generic_ide_ioctl(ide_drive_t *, struct file *, struct block_device *, unsigned, unsigned long);

/*
 * ide_hwifs[] is the master data structure used to keep track
 * of just about everything in ide.c.  Whenever possible, routines
 * should be using pointers to a drive (ide_drive_t *) or
 * pointers to a hwif (ide_hwif_t *), rather than indexing this
 * structure directly (the allocation/layout may change!).
 *
 */
#ifndef _IDE_C
extern	ide_hwif_t	ide_hwifs[];		/* master data repository */
#endif
extern int noautodma;

ide_hwif_t *ide_find_port_slot(const struct ide_port_info *);

static inline ide_hwif_t *ide_find_port(void)
{
	return ide_find_port_slot(NULL);
}

extern int ide_end_request (ide_drive_t *drive, int uptodate, int nrsecs);
int ide_end_dequeued_request(ide_drive_t *drive, struct request *rq,
			     int uptodate, int nr_sectors);

extern void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry);

void ide_execute_command(ide_drive_t *, u8, ide_handler_t *, unsigned int,
			 ide_expiry_t *);

ide_startstop_t __ide_error(ide_drive_t *, struct request *, u8, u8);

ide_startstop_t ide_error (ide_drive_t *drive, const char *msg, byte stat);

ide_startstop_t __ide_abort(ide_drive_t *, struct request *);

extern ide_startstop_t ide_abort(ide_drive_t *, const char *);

extern void ide_fix_driveid(struct hd_driveid *);

extern void ide_fixstring(u8 *, const int, const int);

int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);

extern ide_startstop_t ide_do_reset (ide_drive_t *);

extern void ide_init_drive_cmd (struct request *rq);

/*
 * "action" parameter type for ide_do_drive_cmd() below.
 */
typedef enum {
	ide_wait,	/* insert rq at end of list, and wait for it */
	ide_preempt,	/* insert rq in front of current request */
	ide_head_wait,	/* insert rq in front of current request and wait for it */
	ide_end		/* insert rq at end of list, but don't wait for it */
} ide_action_t;

extern int ide_do_drive_cmd(ide_drive_t *, struct request *, ide_action_t);

extern void ide_end_drive_cmd(ide_drive_t *, u8, u8);

enum {
	IDE_TFLAG_LBA48			= (1 << 0),
	IDE_TFLAG_NO_SELECT_MASK	= (1 << 1),
	IDE_TFLAG_FLAGGED		= (1 << 2),
	IDE_TFLAG_OUT_DATA		= (1 << 3),
	IDE_TFLAG_OUT_HOB_FEATURE	= (1 << 4),
	IDE_TFLAG_OUT_HOB_NSECT		= (1 << 5),
	IDE_TFLAG_OUT_HOB_LBAL		= (1 << 6),
	IDE_TFLAG_OUT_HOB_LBAM		= (1 << 7),
	IDE_TFLAG_OUT_HOB_LBAH		= (1 << 8),
	IDE_TFLAG_OUT_HOB		= IDE_TFLAG_OUT_HOB_FEATURE |
					  IDE_TFLAG_OUT_HOB_NSECT |
					  IDE_TFLAG_OUT_HOB_LBAL |
					  IDE_TFLAG_OUT_HOB_LBAM |
					  IDE_TFLAG_OUT_HOB_LBAH,
	IDE_TFLAG_OUT_FEATURE		= (1 << 9),
	IDE_TFLAG_OUT_NSECT		= (1 << 10),
	IDE_TFLAG_OUT_LBAL		= (1 << 11),
	IDE_TFLAG_OUT_LBAM		= (1 << 12),
	IDE_TFLAG_OUT_LBAH		= (1 << 13),
	IDE_TFLAG_OUT_TF		= IDE_TFLAG_OUT_FEATURE |
					  IDE_TFLAG_OUT_NSECT |
					  IDE_TFLAG_OUT_LBAL |
					  IDE_TFLAG_OUT_LBAM |
					  IDE_TFLAG_OUT_LBAH,
	IDE_TFLAG_OUT_DEVICE		= (1 << 14),
	IDE_TFLAG_WRITE			= (1 << 15),
	IDE_TFLAG_FLAGGED_SET_IN_FLAGS	= (1 << 16),
	IDE_TFLAG_IN_DATA		= (1 << 17),
	IDE_TFLAG_CUSTOM_HANDLER	= (1 << 18),
	IDE_TFLAG_DMA_PIO_FALLBACK	= (1 << 19),
	IDE_TFLAG_IN_HOB_FEATURE	= (1 << 20),
	IDE_TFLAG_IN_HOB_NSECT		= (1 << 21),
	IDE_TFLAG_IN_HOB_LBAL		= (1 << 22),
	IDE_TFLAG_IN_HOB_LBAM		= (1 << 23),
	IDE_TFLAG_IN_HOB_LBAH		= (1 << 24),
	IDE_TFLAG_IN_HOB_LBA		= IDE_TFLAG_IN_HOB_LBAL |
					  IDE_TFLAG_IN_HOB_LBAM |
					  IDE_TFLAG_IN_HOB_LBAH,
	IDE_TFLAG_IN_HOB		= IDE_TFLAG_IN_HOB_FEATURE |
					  IDE_TFLAG_IN_HOB_NSECT |
					  IDE_TFLAG_IN_HOB_LBA,
	IDE_TFLAG_IN_NSECT		= (1 << 25),
	IDE_TFLAG_IN_LBAL		= (1 << 26),
	IDE_TFLAG_IN_LBAM		= (1 << 27),
	IDE_TFLAG_IN_LBAH		= (1 << 28),
	IDE_TFLAG_IN_LBA		= IDE_TFLAG_IN_LBAL |
					  IDE_TFLAG_IN_LBAM |
					  IDE_TFLAG_IN_LBAH,
	IDE_TFLAG_IN_TF			= IDE_TFLAG_IN_NSECT |
					  IDE_TFLAG_IN_LBA,
	IDE_TFLAG_IN_DEVICE		= (1 << 29),
	IDE_TFLAG_HOB			= IDE_TFLAG_OUT_HOB |
					  IDE_TFLAG_IN_HOB,
	IDE_TFLAG_TF			= IDE_TFLAG_OUT_TF |
					  IDE_TFLAG_IN_TF,
	IDE_TFLAG_DEVICE		= IDE_TFLAG_OUT_DEVICE |
					  IDE_TFLAG_IN_DEVICE,
	/* force 16-bit I/O operations */
	IDE_TFLAG_IO_16BIT		= (1 << 30),
	/* ide_task_t was allocated using kmalloc() */
	IDE_TFLAG_DYN			= (1 << 31),
};

struct ide_taskfile {
	u8	hob_data;	/*  0: high data byte (for TASKFILE IOCTL) */

	u8	hob_feature;	/*  1-5: additional data to support LBA48 */
	u8	hob_nsect;
	u8	hob_lbal;
	u8	hob_lbam;
	u8	hob_lbah;

	u8	data;		/*  6: low data byte (for TASKFILE IOCTL) */

	union {			/*  7: */
		u8 error;	/*   read:  error */
		u8 feature;	/*  write: feature */
	};

	u8	nsect;		/*  8: number of sectors */
	u8	lbal;		/*  9: LBA low */
	u8	lbam;		/* 10: LBA mid */
	u8	lbah;		/* 11: LBA high */

	u8	device;		/* 12: device select */

	union {			/* 13: */
		u8 status;	/*  read: status  */
		u8 command;	/* write: command */
	};
};

typedef struct ide_task_s {
	union {
		struct ide_taskfile	tf;
		u8			tf_array[14];
	};
	u32			tf_flags;
	int			data_phase;
	struct request		*rq;		/* copy of request */
	void			*special;	/* valid_t generally */
} ide_task_t;

void ide_tf_load(ide_drive_t *, ide_task_t *);
void ide_tf_read(ide_drive_t *, ide_task_t *);

extern void SELECT_DRIVE(ide_drive_t *);
extern void SELECT_MASK(ide_drive_t *, int);

extern int drive_is_ready(ide_drive_t *);

void ide_pktcmd_tf_load(ide_drive_t *, u32, u16, u8);

ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);

void task_end_request(ide_drive_t *, struct request *, u8);

int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *, u16);
int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);

int ide_taskfile_ioctl(ide_drive_t *, unsigned int, unsigned long);
int ide_cmd_ioctl(ide_drive_t *, unsigned int, unsigned long);
int ide_task_ioctl(ide_drive_t *, unsigned int, unsigned long);

extern int system_bus_clock(void);

extern int ide_driveid_update(ide_drive_t *);
extern int ide_config_drive_speed(ide_drive_t *, u8);
extern u8 eighty_ninty_three (ide_drive_t *);
extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);

extern int ide_wait_not_busy(ide_hwif_t *hwif, unsigned long timeout);

extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);

extern int ide_spin_wait_hwgroup(ide_drive_t *);
extern void ide_timer_expiry(unsigned long);
extern irqreturn_t ide_intr(int irq, void *dev_id);
extern void do_ide_request(struct request_queue *);

void ide_init_disk(struct gendisk *, ide_drive_t *);

#ifdef CONFIG_IDEPCI_PCIBUS_ORDER
extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
#define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
#else
#define ide_pci_register_driver(d) pci_register_driver(d)
#endif

void ide_pci_setup_ports(struct pci_dev *, const struct ide_port_info *, int, u8 *);
void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);

#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
void ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
#else
static inline void ide_hwif_setup_dma(ide_hwif_t *hwif,
				      const struct ide_port_info *d) { }
#endif

extern void default_hwif_iops(ide_hwif_t *);
extern void default_hwif_mmiops(ide_hwif_t *);
extern void default_hwif_transport(ide_hwif_t *);

typedef struct ide_pci_enablebit_s {
	u8	reg;	/* byte pci reg holding the enable-bit */
	u8	mask;	/* mask to isolate the enable-bit */
	u8	val;	/* value of masked reg when "enabled" */
} ide_pci_enablebit_t;

enum {
	/* Uses ISA control ports not PCI ones. */
	IDE_HFLAG_ISA_PORTS		= (1 << 0),
	/* single port device */
	IDE_HFLAG_SINGLE		= (1 << 1),
	/* don't use legacy PIO blacklist */
	IDE_HFLAG_PIO_NO_BLACKLIST	= (1 << 2),
	/* set for the second port of QD65xx */
	IDE_HFLAG_QD_2ND_PORT		= (1 << 3),
	/* use PIO8/9 for prefetch off/on */
	IDE_HFLAG_ABUSE_PREFETCH	= (1 << 4),
	/* use PIO6/7 for fast-devsel off/on */
	IDE_HFLAG_ABUSE_FAST_DEVSEL	= (1 << 5),
	/* use 100-102 and 200-202 PIO values to set DMA modes */
	IDE_HFLAG_ABUSE_DMA_MODES	= (1 << 6),
	/*
	 * keep DMA setting when programming PIO mode, may be used only
	 * for hosts which have separate PIO and DMA timings (ie. PMAC)
	 */
	IDE_HFLAG_SET_PIO_MODE_KEEP_DMA	= (1 << 7),
	/* program host for the transfer mode after programming device */
	IDE_HFLAG_POST_SET_MODE		= (1 << 8),
	/* don't program host/device for the transfer mode ("smart" hosts) */
	IDE_HFLAG_NO_SET_MODE		= (1 << 9),
	/* trust BIOS for programming chipset/device for DMA */
	IDE_HFLAG_TRUST_BIOS_FOR_DMA	= (1 << 10),
	/* host uses VDMA (tied with IDE_HFLAG_CS5520 for now) */
	IDE_HFLAG_VDMA			= (1 << 11),
	/* ATAPI DMA is unsupported */
	IDE_HFLAG_NO_ATAPI_DMA		= (1 << 12),
	/* set if host is a "non-bootable" controller */
	IDE_HFLAG_NON_BOOTABLE		= (1 << 13),
	/* host doesn't support DMA */
	IDE_HFLAG_NO_DMA		= (1 << 14),
	/* check if host is PCI IDE device before allowing DMA */
	IDE_HFLAG_NO_AUTODMA		= (1 << 15),
	/* don't autotune PIO */
	IDE_HFLAG_NO_AUTOTUNE		= (1 << 16),
	/* host is CS5510/CS5520 */
	IDE_HFLAG_CS5520		= IDE_HFLAG_VDMA,
	/* no LBA48 */
	IDE_HFLAG_NO_LBA48		= (1 << 17),
	/* no LBA48 DMA */
	IDE_HFLAG_NO_LBA48_DMA		= (1 << 18),
	/* data FIFO is cleared by an error */
	IDE_HFLAG_ERROR_STOPS_FIFO	= (1 << 19),
	/* serialize ports */
	IDE_HFLAG_SERIALIZE		= (1 << 20),
	/* use legacy IRQs */
	IDE_HFLAG_LEGACY_IRQS		= (1 << 21),
	/* force use of legacy IRQs */
	IDE_HFLAG_FORCE_LEGACY_IRQS	= (1 << 22),
	/* limit LBA48 requests to 256 sectors */
	IDE_HFLAG_RQSIZE_256		= (1 << 23),
	/* use 32-bit I/O ops */
	IDE_HFLAG_IO_32BIT		= (1 << 24),
	/* unmask IRQs */
	IDE_HFLAG_UNMASK_IRQS		= (1 << 25),
	IDE_HFLAG_ABUSE_SET_DMA_MODE	= (1 << 26),
	/* force host out of "simplex" mode */
	IDE_HFLAG_CLEAR_SIMPLEX		= (1 << 28),
	/* DSC overlap is unsupported */
	IDE_HFLAG_NO_DSC		= (1 << 29),
	/* never use 32-bit I/O ops */
	IDE_HFLAG_NO_IO_32BIT		= (1 << 30),
	/* never unmask IRQs */
	IDE_HFLAG_NO_UNMASK_IRQS	= (1 << 31),
};

#ifdef CONFIG_BLK_DEV_OFFBOARD
# define IDE_HFLAG_OFF_BOARD	0
#else
# define IDE_HFLAG_OFF_BOARD	IDE_HFLAG_NON_BOOTABLE
#endif

struct ide_port_info {
	char			*name;
	unsigned int		(*init_chipset)(struct pci_dev *, const char *);
	void			(*init_iops)(ide_hwif_t *);
	void                    (*init_hwif)(ide_hwif_t *);
	void			(*init_dma)(ide_hwif_t *, unsigned long);

	const struct ide_port_ops	*port_ops;

	ide_pci_enablebit_t	enablebits[2];
	hwif_chipset_t		chipset;
	u32			host_flags;
	u8			pio_mask;
	u8			swdma_mask;
	u8			mwdma_mask;
	u8			udma_mask;
};

int ide_setup_pci_device(struct pci_dev *, const struct ide_port_info *);
int ide_setup_pci_devices(struct pci_dev *, struct pci_dev *, const struct ide_port_info *);

void ide_map_sg(ide_drive_t *, struct request *);
void ide_init_sg_cmd(ide_drive_t *, struct request *);

#define BAD_DMA_DRIVE		0
#define GOOD_DMA_DRIVE		1

struct drive_list_entry {
	const char *id_model;
	const char *id_firmware;
};

int ide_in_drive_list(struct hd_driveid *, const struct drive_list_entry *);

#ifdef CONFIG_BLK_DEV_IDEDMA
int __ide_dma_bad_drive(ide_drive_t *);
int ide_id_dma_bug(ide_drive_t *);

u8 ide_find_dma_mode(ide_drive_t *, u8);

static inline u8 ide_max_dma_mode(ide_drive_t *drive)
{
	return ide_find_dma_mode(drive, XFER_UDMA_6);
}

void ide_dma_off_quietly(ide_drive_t *);
void ide_dma_off(ide_drive_t *);
void ide_dma_on(ide_drive_t *);
int ide_set_dma(ide_drive_t *);
void ide_check_dma_crc(ide_drive_t *);
ide_startstop_t ide_dma_intr(ide_drive_t *);

int ide_build_sglist(ide_drive_t *, struct request *);
void ide_destroy_dmatable(ide_drive_t *);

#ifdef CONFIG_BLK_DEV_IDEDMA_SFF
extern int ide_build_dmatable(ide_drive_t *, struct request *);
int ide_allocate_dma_engine(ide_hwif_t *);
void ide_release_dma_engine(ide_hwif_t *);
extern void ide_setup_dma(ide_hwif_t *, unsigned long);

void ide_dma_host_set(ide_drive_t *, int);
extern int ide_dma_setup(ide_drive_t *);
extern void ide_dma_start(ide_drive_t *);
extern int __ide_dma_end(ide_drive_t *);
extern void ide_dma_lost_irq(ide_drive_t *);
extern void ide_dma_timeout(ide_drive_t *);
#endif /* CONFIG_BLK_DEV_IDEDMA_SFF */

#else
static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
static inline void ide_dma_off(ide_drive_t *drive) { ; }
static inline void ide_dma_on(ide_drive_t *drive) { ; }
static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
static inline void ide_check_dma_crc(ide_drive_t *drive) { ; }
#endif /* CONFIG_BLK_DEV_IDEDMA */

#ifndef CONFIG_BLK_DEV_IDEDMA_SFF
static inline void ide_release_dma_engine(ide_hwif_t *hwif) { ; }
#endif

#ifdef CONFIG_BLK_DEV_IDEACPI
extern int ide_acpi_exec_tfs(ide_drive_t *drive);
extern void ide_acpi_get_timing(ide_hwif_t *hwif);
extern void ide_acpi_push_timing(ide_hwif_t *hwif);
extern void ide_acpi_init(ide_hwif_t *hwif);
void ide_acpi_port_init_devices(ide_hwif_t *);
extern void ide_acpi_set_state(ide_hwif_t *hwif, int on);
#else
static inline int ide_acpi_exec_tfs(ide_drive_t *drive) { return 0; }
static inline void ide_acpi_get_timing(ide_hwif_t *hwif) { ; }
static inline void ide_acpi_push_timing(ide_hwif_t *hwif) { ; }
static inline void ide_acpi_init(ide_hwif_t *hwif) { ; }
static inline void ide_acpi_port_init_devices(ide_hwif_t *hwif) { ; }
static inline void ide_acpi_set_state(ide_hwif_t *hwif, int on) {}
#endif

void ide_remove_port_from_hwgroup(ide_hwif_t *);
void ide_unregister(unsigned int);

void ide_register_region(struct gendisk *);
void ide_unregister_region(struct gendisk *);

void ide_undecoded_slave(ide_drive_t *);

int ide_device_add_all(u8 *idx, const struct ide_port_info *);
int ide_device_add(u8 idx[4], const struct ide_port_info *);
int ide_legacy_device_add(const struct ide_port_info *, unsigned long);
void ide_port_unregister_devices(ide_hwif_t *);
void ide_port_scan(ide_hwif_t *);

static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
{
	return hwif->hwif_data;
}

static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
{
	hwif->hwif_data = data;
}

const char *ide_xfer_verbose(u8 mode);
extern void ide_toggle_bounce(ide_drive_t *drive, int on);
extern int ide_set_xfer_rate(ide_drive_t *drive, u8 rate);

static inline int ide_dev_has_iordy(struct hd_driveid *id)
{
	return ((id->field_valid & 2) && (id->capability & 8)) ? 1 : 0;
}

static inline int ide_dev_is_sata(struct hd_driveid *id)
{
	/*
	 * See if word 93 is 0 AND drive is at least ATA-5 compatible
	 * verifying that word 80 by casting it to a signed type --
	 * this trick allows us to filter out the reserved values of
	 * 0x0000 and 0xffff along with the earlier ATA revisions...
	 */
	if (id->hw_config == 0 && (short)id->major_rev_num >= 0x0020)
		return 1;
	return 0;
}

u64 ide_get_lba_addr(struct ide_taskfile *, int);
u8 ide_dump_status(ide_drive_t *, const char *, u8);

typedef struct ide_pio_timings_s {
	int	setup_time;	/* Address setup (ns) minimum */
	int	active_time;	/* Active pulse (ns) minimum */
	int	cycle_time;	/* Cycle time (ns) minimum = */
				/* active + recovery (+ setup for some chips) */
} ide_pio_timings_t;

unsigned int ide_pio_cycle_time(ide_drive_t *, u8);
u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
extern const ide_pio_timings_t ide_pio_timings[6];

int ide_set_pio_mode(ide_drive_t *, u8);
int ide_set_dma_mode(ide_drive_t *, u8);

void ide_set_pio(ide_drive_t *, u8);

static inline void ide_set_max_pio(ide_drive_t *drive)
{
	ide_set_pio(drive, 255);
}

extern spinlock_t ide_lock;
extern struct mutex ide_cfg_mtx;
/*
 * Structure locking:
 *
 * ide_cfg_mtx and ide_lock together protect changes to
 * ide_hwif_t->{next,hwgroup}
 * ide_drive_t->next
 *
 * ide_hwgroup_t->busy: ide_lock
 * ide_hwgroup_t->hwif: ide_lock
 * ide_hwif_t->mate: constant, no locking
 * ide_drive_t->hwif: constant, no locking
 */

#define local_irq_set(flags)	do { local_save_flags((flags)); local_irq_enable_in_hardirq(); } while (0)

extern struct bus_type ide_bus_type;
extern struct class *ide_port_class;

/* check if CACHE FLUSH (EXT) command is supported (bits defined in ATA-6) */
#define ide_id_has_flush_cache(id)	((id)->cfs_enable_2 & 0x3000)

/* some Maxtor disks have bit 13 defined incorrectly so check bit 10 too */
#define ide_id_has_flush_cache_ext(id)	\
	(((id)->cfs_enable_2 & 0x2400) == 0x2400)

static inline void ide_dump_identify(u8 *id)
{
	print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 2, id, 512, 0);
}

static inline int hwif_to_node(ide_hwif_t *hwif)
{
	struct pci_dev *dev = to_pci_dev(hwif->dev);
	return hwif->dev ? pcibus_to_node(dev->bus) : -1;
}

static inline ide_drive_t *ide_get_paired_drive(ide_drive_t *drive)
{
	ide_hwif_t *hwif	= HWIF(drive);

	return &hwif->drives[(drive->dn ^ 1) & 1];
}

static inline void ide_set_irq(ide_drive_t *drive, int on)
{
	ide_hwif_t *hwif = drive->hwif;

	hwif->OUTB(drive->ctl | (on ? 0 : 2),
		   hwif->io_ports[IDE_CONTROL_OFFSET]);
}

static inline u8 ide_read_status(ide_drive_t *drive)
{
	ide_hwif_t *hwif = drive->hwif;

	return hwif->INB(hwif->io_ports[IDE_STATUS_OFFSET]);
}

static inline u8 ide_read_altstatus(ide_drive_t *drive)
{
	ide_hwif_t *hwif = drive->hwif;

	return hwif->INB(hwif->io_ports[IDE_CONTROL_OFFSET]);
}

static inline u8 ide_read_error(ide_drive_t *drive)
{
	ide_hwif_t *hwif = drive->hwif;

	return hwif->INB(hwif->io_ports[IDE_ERROR_OFFSET]);
}

/*
 * Too bad. The drive wants to send us data which we are not ready to accept.
 * Just throw it away.
 */
static inline void ide_atapi_discard_data(ide_drive_t *drive, unsigned bcount)
{
	ide_hwif_t *hwif = drive->hwif;

	/* FIXME: use ->atapi_input_bytes */
	while (bcount--)
		(void)hwif->INB(hwif->io_ports[IDE_DATA_OFFSET]);
}

static inline void ide_atapi_write_zeros(ide_drive_t *drive, unsigned bcount)
{
	ide_hwif_t *hwif = drive->hwif;

	/* FIXME: use ->atapi_output_bytes */
	while (bcount--)
		hwif->OUTB(0, hwif->io_ports[IDE_DATA_OFFSET]);
}

#endif /* _IDE_H */