linux-vybrid_public/drivers/ide/Kconfig

#
# IDE ATA ATAPI Block device driver configuration
#

# Select HAVE_IDE if IDE is supported
config HAVE_IDE
	bool

menuconfig IDE
	tristate "ATA/ATAPI/MFM/RLL support"
	depends on HAVE_IDE
	depends on BLOCK
	---help---
	  If you say Y here, your kernel will be able to manage low cost mass
	  storage units such as ATA/(E)IDE and ATAPI units. The most common
	  cases are IDE hard drives and ATAPI CD-ROM drives.

	  If your system is pure SCSI and doesn't use these interfaces, you
	  can say N here.

	  Integrated Disk Electronics (IDE aka ATA-1) is a connecting standard
	  for mass storage units such as hard disks. It was designed by
	  Western Digital and Compaq Computer in 1984. It was then named
	  ST506. Quite a number of disks use the IDE interface.

	  AT Attachment (ATA) is the superset of the IDE specifications.
	  ST506 was also called ATA-1.

	  Fast-IDE is ATA-2 (also named Fast ATA), Enhanced IDE (EIDE) is
	  ATA-3. It provides support for larger disks (up to 8.4GB by means of
	  the LBA standard), more disks (4 instead of 2) and for other mass
	  storage units such as tapes and cdrom. UDMA/33 (aka UltraDMA/33) is
	  ATA-4 and provides faster (and more CPU friendly) transfer modes
	  than previous PIO (Programmed processor Input/Output) from previous
	  ATA/IDE standards by means of fast DMA controllers.

	  ATA Packet Interface (ATAPI) is a protocol used by EIDE tape and
	  CD-ROM drives, similar in many respects to the SCSI protocol.

	  SMART IDE (Self Monitoring, Analysis and Reporting Technology) was
	  designed in order to prevent data corruption and disk crash by
	  detecting pre hardware failure conditions (heat, access time, and
	  the like...). Disks built since June 1995 may follow this standard.
	  The kernel itself doesn't manage this; however there are quite a
	  number of user programs such as smart that can query the status of
	  SMART parameters from disk drives.

	  To compile this driver as a module, choose M here: the
	  module will be called ide-core.ko.

	  For further information, please read <file:Documentation/ide/ide.txt>.

	  If unsure, say Y.

if IDE

comment "Please see Documentation/ide/ide.txt for help/info on IDE drives"

config IDE_XFER_MODE
	bool

config IDE_TIMINGS
	bool
	select IDE_XFER_MODE

config IDE_ATAPI
	bool

config IDE_LEGACY
	bool

config BLK_DEV_IDE_SATA
	bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
	default n
	---help---
	  There are two drivers for Serial ATA controllers.

	  The main driver, "libata", uses the SCSI subsystem
	  and supports most modern SATA controllers. In order to use it
	  you may take a look at "Serial ATA (prod) and Parallel ATA
	  (experimental) drivers".

	  The IDE driver (which you are currently configuring) supports
	  a few first-generation SATA controllers.

	  In order to eliminate conflicts between the two subsystems,
	  this config option enables the IDE driver's SATA support.
	  Normally this is disabled, as it is preferred that libata
	  supports SATA controllers, and this (IDE) driver supports
	  PATA controllers.

	  If unsure, say N.

config IDE_GD
	tristate "generic ATA/ATAPI disk support"
	default y
	help
	  Support for ATA/ATAPI disks (including ATAPI floppy drives).

	  To compile this driver as a module, choose M here.
	  The module will be called ide-gd_mod.

	  If unsure, say Y.

config IDE_GD_ATA
	bool "ATA disk support"
	depends on IDE_GD
	default y
	help
	  This will include support for ATA hard disks.

	  If unsure, say Y.

config IDE_GD_ATAPI
	bool "ATAPI floppy support"
	depends on IDE_GD
	select IDE_ATAPI
	help
	  This will include support for ATAPI floppy drives
	  (i.e. Iomega ZIP or MKE LS-120).

	  For information about jumper settings and the question
	  of when a ZIP drive uses a partition table, see
	  <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.

	  If unsure, say N.

config BLK_DEV_IDECS
	tristate "PCMCIA IDE support"
	depends on PCMCIA
	help
	  Support for Compact Flash cards, outboard IDE disks, tape drives,
	  and CD-ROM drives connected through a PCMCIA card.

config BLK_DEV_DELKIN
	tristate "Cardbus IDE support (Delkin/ASKA/Workbit)"
	depends on CARDBUS && PCI
	help
	  Support for Delkin, ASKA, and Workbit Cardbus CompactFlash
	  Adapters.  This may also work for similar SD and XD adapters.

config BLK_DEV_IDECD
	tristate "Include IDE/ATAPI CDROM support"
	select IDE_ATAPI
	---help---
	  If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
	  a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
	  SCSI protocol. Most new CD-ROM drives use ATAPI, including the
	  NEC-260, Mitsumi FX400, Sony 55E, and just about all non-SCSI
	  double(2X) or better speed drives.

	  If you say Y here, the CD-ROM drive will be identified at boot time
	  along with other IDE devices, as "hdb" or "hdc", or something
	  similar (check the boot messages with dmesg). If this is your only
	  CD-ROM drive, you can say N to all other CD-ROM options, but be sure
	  to say Y or M to "ISO 9660 CD-ROM file system support".

	  To compile this driver as a module, choose M here: the
	  module will be called ide-cd.

config BLK_DEV_IDECD_VERBOSE_ERRORS
	bool "Verbose error logging for IDE/ATAPI CDROM driver" if EMBEDDED
	depends on BLK_DEV_IDECD
	default y
	help
	  Turn this on to have the driver print out the meanings of the
	  ATAPI error codes.  This will use up additional 8kB of kernel-space
	  memory, though.

config BLK_DEV_IDETAPE
	tristate "Include IDE/ATAPI TAPE support"
	select IDE_ATAPI
	help
	  If you have an IDE tape drive using the ATAPI protocol, say Y.
	  ATAPI is a newer protocol used by IDE tape and CD-ROM drives,
	  similar to the SCSI protocol.  If you have an SCSI tape drive
	  however, you can say N here.

	  You should also say Y if you have an OnStream DI-30 tape drive; this
	  will not work with the SCSI protocol, until there is support for the
	  SC-30 and SC-50 versions.

	  If you say Y here, the tape drive will be identified at boot time
	  along with other IDE devices, as "hdb" or "hdc", or something
	  similar, and will be mapped to a character device such as "ht0"
	  (check the boot messages with dmesg).  Be sure to consult the
	  <file:drivers/ide/ide-tape.c> and <file:Documentation/ide/ide.txt>
	  files for usage information.

	  To compile this driver as a module, choose M here: the
	  module will be called ide-tape.

config BLK_DEV_IDEACPI
	bool "IDE ACPI support"
	depends on ACPI
	---help---
	  Implement ACPI support for generic IDE devices. On modern
	  machines ACPI support is required to properly handle ACPI S3 states.

config IDE_TASK_IOCTL
	bool "IDE Taskfile Access"
	help
	  This is a direct raw access to the media.  It is a complex but
	  elegant solution to test and validate the domain of the hardware and
	  perform below the driver data recovery if needed.  This is the most
	  basic form of media-forensics.

	  If you are unsure, say N here.

config IDE_PROC_FS
	bool "legacy /proc/ide/ support"
	depends on IDE && PROC_FS
	default y
	help
	  This option enables support for the various files in
	  /proc/ide.  In Linux 2.6 this has been superseded by
	  files in sysfs but many legacy applications rely on this.

	  If unsure say Y.

comment "IDE chipset support/bugfixes"

config IDE_GENERIC
	tristate "generic/default IDE chipset support"
	depends on ALPHA || X86 || IA64 || M32R || MIPS || ARCH_RPC || ARCH_SHARK
	default ARM && (ARCH_RPC || ARCH_SHARK)
	help
	  This is the generic IDE driver.  This driver attaches to the
	  fixed legacy ports (e.g. on PCs 0x1f0/0x170, 0x1e8/0x168 and
	  so on).  Please note that if this driver is built into the
	  kernel or loaded before other ATA (IDE or libata) drivers
	  and the controller is located at legacy ports, this driver
	  may grab those ports and thus can prevent the controller
	  specific driver from attaching.

	  Also, currently, IDE generic doesn't allow IRQ sharing
	  meaning that the IRQs it grabs won't be available to other
	  controllers sharing those IRQs which usually makes drivers
	  for those controllers fail.  Generally, it's not a good idea
	  to load IDE generic driver on modern systems.

	  If unsure, say N.

config BLK_DEV_PLATFORM
	tristate "Platform driver for IDE interfaces"
	help
	  This is the platform IDE driver, used mostly for Memory Mapped
	  IDE devices, like Compact Flashes running in True IDE mode.

	  If unsure, say N.

config BLK_DEV_CMD640
	tristate "CMD640 chipset bugfix/support"
	depends on X86
	select IDE_TIMINGS
	---help---
	  The CMD-Technologies CMD640 IDE chip is used on many common 486 and
	  Pentium motherboards, usually in combination with a "Neptune" or
	  "SiS" chipset. Unfortunately, it has a number of rather nasty
	  design flaws that can cause severe data corruption under many common
	  conditions. Say Y here to include code which tries to automatically
	  detect and correct the problems under Linux. This option also
	  enables access to the secondary IDE ports in some CMD640 based
	  systems.

	  This driver will work automatically in PCI based systems (most new
	  systems have PCI slots). But if your system uses VESA local bus
	  (VLB) instead of PCI, you must also supply a kernel boot parameter
	  to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man
	  bootparam" or see the documentation of your boot loader about how to
	  pass options to the kernel.)

	  The CMD640 chip is also used on add-in cards by Acculogic, and on
	  the "CSA-6400E PCI to IDE controller" that some people have. For
	  details, read <file:Documentation/ide/ide.txt>.

config BLK_DEV_CMD640_ENHANCED
	bool "CMD640 enhanced support"
	depends on BLK_DEV_CMD640
	help
	  This option includes support for setting/autotuning PIO modes and
	  prefetch on CMD640 IDE interfaces.  For details, read
	  <file:Documentation/ide/ide.txt>. If you have a CMD640 IDE interface
	  and your BIOS does not already do this for you, then say Y here.
	  Otherwise say N.

config BLK_DEV_IDEPNP
	tristate "PNP EIDE support"
	depends on PNP
	help
	  If you have a PnP (Plug and Play) compatible EIDE card and
	  would like the kernel to automatically detect and activate
	  it, say Y here.

config BLK_DEV_IDEDMA_SFF
	bool

if PCI

comment "PCI IDE chipsets support"

config BLK_DEV_IDEPCI
	bool

config IDEPCI_PCIBUS_ORDER
	bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
	depends on IDE=y && BLK_DEV_IDEPCI
	default y
	help
	  Probe IDE PCI devices in the order in which they appear on the
	  PCI bus (i.e. 00:1f.1 PCI device before 02:01.0 PCI device)
	  instead of the order in which IDE PCI host drivers are loaded.

	  Please note that this method of assuring stable naming of
	  IDE devices is unreliable and use other means for achieving
	  it (i.e. udev).

	  If in doubt, say N.

# TODO: split it on per host driver config options (or module parameters)
config BLK_DEV_OFFBOARD
	bool "Boot off-board chipsets first support (DEPRECATED)"
	depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
	help
	  Normally, IDE controllers built into the motherboard (on-board
	  controllers) are assigned to ide0 and ide1 while those on add-in PCI
	  cards (off-board controllers) are relegated to ide2 and ide3.
	  Answering Y here will allow you to reverse the situation, with
	  off-board controllers on ide0/1 and on-board controllers on ide2/3.
	  This can improve the usability of some boot managers such as lilo
	  when booting from a drive on an off-board controller.

	  Note that, if you do this, the order of the hd* devices will be
	  rearranged which may require modification of fstab and other files.

	  Please also note that this method of assuring stable naming of
	  IDE devices is unreliable and use other means for achieving it
	  (i.e. udev).

	  If in doubt, say N.

config BLK_DEV_GENERIC
	tristate "Generic PCI IDE Chipset Support"
	select BLK_DEV_IDEPCI
        help
          This option provides generic support for various PCI IDE Chipsets
          which otherwise might not be supported.

config BLK_DEV_OPTI621
	tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	select BLK_DEV_IDEPCI
	help
	  This is a driver for the OPTi 82C621 EIDE controller.
	  Please read the comments at the top of <file:drivers/ide/pci/opti621.c>.

config BLK_DEV_RZ1000
	tristate "RZ1000 chipset bugfix/support"
	depends on X86
	select BLK_DEV_IDEPCI
	help
	  The PC-Technologies RZ1000 IDE chip is used on many common 486 and
	  Pentium motherboards, usually along with the "Neptune" chipset.
	  Unfortunately, it has a rather nasty design flaw that can cause
	  severe data corruption under many conditions. Say Y here to include
	  code which automatically detects and corrects the problem under
	  Linux. This may slow disk throughput by a few percent, but at least
	  things will operate 100% reliably.

config BLK_DEV_IDEDMA_PCI
	bool
	select BLK_DEV_IDEPCI
	select BLK_DEV_IDEDMA_SFF

config BLK_DEV_AEC62XX
	tristate "AEC62XX chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds explicit support for Acard AEC62xx (Artop ATP8xx)
	  IDE controllers. This allows the kernel to change PIO, DMA and UDMA
	  speeds and to configure the chip to optimum performance.

config BLK_DEV_ALI15X3
	tristate "ALI M15x3 chipset support"
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver ensures (U)DMA support for ALI 1533, 1543 and 1543C
	  onboard chipsets.  It also tests for Simplex mode and enables
	  normal dual channel support.

	  Please read the comments at the top of
	  <file:drivers/ide/pci/alim15x3.c>.

	  If unsure, say N.

config BLK_DEV_AMD74XX
	tristate "AMD and nVidia IDE support"
	depends on !ARM
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds explicit support for AMD-7xx and AMD-8111 chips
	  and also for the nVidia nForce chip.  This allows the kernel to
	  change PIO, DMA and UDMA speeds and to configure the chip to
	  optimum performance.

config BLK_DEV_ATIIXP
	tristate "ATI IXP chipset IDE support"
	depends on X86
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds explicit support for ATI IXP chipset.
	  This allows the kernel to change PIO, DMA and UDMA speeds
	  and to configure the chip to optimum performance.

	  Say Y here if you have an ATI IXP chipset IDE controller.

config BLK_DEV_CMD64X
	tristate "CMD64{3|6|8|9} chipset support"
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_PCI
	help
	  Say Y here if you have an IDE controller which uses any of these
	  chipsets: CMD643, CMD646, or CMD648.

config BLK_DEV_TRIFLEX
	tristate "Compaq Triflex IDE support"
	select BLK_DEV_IDEDMA_PCI
	help
	  Say Y here if you have a Compaq Triflex IDE controller, such
	  as those commonly found on Compaq Pentium-Pro systems

config BLK_DEV_CY82C693
	tristate "CY82C693 chipset support"
	depends on ALPHA
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds detection and support for the CY82C693 chipset
	  used on Digital's PC-Alpha 164SX boards.

config BLK_DEV_CS5520
	tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
	depends on EXPERIMENTAL
	select BLK_DEV_IDEDMA_PCI
	help
	  Include support for PIO tuning and virtual DMA on the Cyrix MediaGX
	  5510/5520 chipset. This will automatically be detected and
	  configured if found.

	  It is safe to say Y to this question.

config BLK_DEV_CS5530
	tristate "Cyrix/National Semiconductor CS5530 MediaGX chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  Include support for UDMA on the Cyrix MediaGX 5530 chipset. This
	  will automatically be detected and configured if found.

	  It is safe to say Y to this question.

config BLK_DEV_CS5535
	tristate "AMD CS5535 chipset support"
	depends on X86 && !X86_64
	select BLK_DEV_IDEDMA_PCI
	help
	  Include support for UDMA on the NSC/AMD CS5535 companion chipset.
	  This will automatically be detected and configured if found.

	  It is safe to say Y to this question.

config BLK_DEV_CS5536
	tristate "CS5536 chipset support"
	depends on X86_32
	select BLK_DEV_IDEDMA_PCI
	help
	  This option enables support for the AMD CS5536
	  companion chip used with the Geode LX processor family.

	  If unsure, say N.

config BLK_DEV_HPT366
	tristate "HPT36X/37X chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  HPT366 is an Ultra DMA chipset for ATA-66.
	  HPT368 is an Ultra DMA chipset for ATA-66 RAID Based.
	  HPT370 is an Ultra DMA chipset for ATA-100.
	  HPT372 is an Ultra DMA chipset for ATA-100.
	  HPT374 is an Ultra DMA chipset for ATA-100.

	  This driver adds up to 4 more EIDE devices sharing a single
	  interrupt.

	  The HPT366 chipset in its current form is bootable. One solution
	  for this problem are special LILO commands for redirecting the
	  reference to device 0x80. The other solution is to say Y to "Boot
	  off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless
	  your mother board has the chipset natively mounted. Regardless one
	  should use the fore mentioned option and call at LILO.

	  This driver requires dynamic tuning of the chipset during the
	  ide-probe at boot. It is reported to support DVD II drives, by the
	  manufacturer.

config BLK_DEV_JMICRON
	tristate "JMicron JMB36x support"
	select BLK_DEV_IDEDMA_PCI
	help
	  Basic support for the JMicron ATA controllers. For full support
	  use the libata drivers.

config BLK_DEV_SC1200
	tristate "National SCx200 chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds support for the on-board IDE controller on the
	  National SCx200 series of embedded x86 "Geode" systems.

config BLK_DEV_PIIX
	tristate "Intel PIIX/ICH chipsets support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds explicit support for Intel PIIX and ICH chips.
	  This allows the kernel to change PIO, DMA and UDMA speeds and to
	  configure the chip to optimum performance.

config BLK_DEV_IT8172
	tristate "IT8172 IDE support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds support for the IDE controller on the
	  IT8172 System Controller.

config BLK_DEV_IT8213
	tristate "IT8213 IDE support"
	select BLK_DEV_IDEDMA_PCI
	help
	 This driver adds support for the ITE 8213 IDE controller.

config BLK_DEV_IT821X
	tristate "IT821X IDE support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds support for the ITE 8211 IDE controller and the
	  IT 8212 IDE RAID controller in both RAID and pass-through mode.

config BLK_DEV_NS87415
	tristate "NS87415 chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds detection and support for the NS87415 chip
	  (used mainly on SPARC64 and PA-RISC machines).

	  Please read the comments at the top of <file:drivers/ide/pci/ns87415.c>.

config BLK_DEV_PDC202XX_OLD
	tristate "PROMISE PDC202{46|62|65|67} support"
	select BLK_DEV_IDEDMA_PCI
	help
	  Promise Ultra33 or PDC20246
	  Promise Ultra66 or PDC20262
	  Promise Ultra100 or PDC20265/PDC20267/PDC20268

	  This driver adds up to 4 more EIDE devices sharing a single
	  interrupt. This add-on card is a bootable PCI UDMA controller. Since
	  multiple cards can be installed and there are BIOS ROM problems that
	  happen if the BIOS revisions of all installed cards (three-max) do
	  not match, the driver attempts to do dynamic tuning of the chipset
	  at boot-time for max-speed.  Ultra33 BIOS 1.25 or newer is required
	  for more than one card.

	  Please read the comments at the top of
	  <file:drivers/ide/pci/pdc202xx_old.c>.

	  If unsure, say N.

config BLK_DEV_PDC202XX_NEW
	tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
	select BLK_DEV_IDEDMA_PCI

config BLK_DEV_SVWKS
	tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds PIO/(U)DMA support for the ServerWorks OSB4/CSB5
	  chipsets.

config BLK_DEV_SGIIOC4
	tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
	depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
	  chipset, which has one channel and can support two devices.
	  Please say Y here if you have an Altix System from SGI.

config BLK_DEV_SIIMAGE
	tristate "Silicon Image chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds PIO/(U)DMA support for the SI CMD680 and SII
	  3112 (Serial ATA) chips.

config BLK_DEV_SIS5513
	tristate "SiS5513 chipset support"
	depends on X86
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver ensures (U)DMA support for SIS5513 chipset family based
	  mainboards.

	  The following chipsets are supported:
	  ATA16:  SiS5511, SiS5513
	  ATA33:  SiS5591, SiS5597, SiS5598, SiS5600
	  ATA66:  SiS530, SiS540, SiS620, SiS630, SiS640
	  ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740,
	  SiS745, SiS750

	  Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.

config BLK_DEV_SL82C105
	tristate "Winbond SL82c105 support"
	depends on (PPC || ARM)
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_PCI
	help
	  If you have a Winbond SL82c105 IDE controller, say Y here to enable
	  special configuration for this chip. This is common on various CHRP
	  motherboards, but could be used elsewhere. If in doubt, say Y.

config BLK_DEV_SLC90E66
	tristate "SLC90E66 chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver ensures (U)DMA support for Victory66 SouthBridges for
	  SMsC with Intel NorthBridges.  This is an Ultra66 based chipset.
	  The nice thing about it is that you can mix Ultra/DMA/PIO devices
	  and it will handle timing cycles.  Since this is an improved
	  look-a-like to the PIIX4 it should be a nice addition.

	  Please read the comments at the top of
	  <file:drivers/ide/pci/slc90e66.c>.

config BLK_DEV_TRM290
	tristate "Tekram TRM290 chipset support"
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds support for bus master DMA transfers
	  using the Tekram TRM290 PCI IDE chip. Volunteers are
	  needed for further tweaking and development.
	  Please read the comments at the top of <file:drivers/ide/pci/trm290.c>.

config BLK_DEV_VIA82CXXX
	tristate "VIA82CXXX chipset support"
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver adds explicit support for VIA BusMastering IDE chips.
	  This allows the kernel to change PIO, DMA and UDMA speeds and to
	  configure the chip to optimum performance.

config BLK_DEV_TC86C001
	tristate "Toshiba TC86C001 support"
	select BLK_DEV_IDEDMA_PCI
	help
	This driver adds support for Toshiba TC86C001 GOKU-S chip.

config BLK_DEV_CELLEB
	tristate "Toshiba's Cell Reference Set IDE support"
	depends on PPC_CELLEB
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver provides support for the on-board IDE controller on
	  Toshiba Cell Reference Board.
	  If unsure, say Y.

endif

# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
config BLK_DEV_IDE_PMAC
	tristate "PowerMac on-board IDE support"
	depends on PPC_PMAC
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_PCI
	help
	  This driver provides support for the on-board IDE controller on
	  most of the recent Apple Power Macintoshes and PowerBooks.
	  If unsure, say Y.

config BLK_DEV_IDE_PMAC_ATA100FIRST
	bool "Probe on-board ATA/100 (Kauai) first"
	depends on BLK_DEV_IDE_PMAC
	help
	  This option will cause the ATA/100 controller found in UniNorth2
	  based machines (Windtunnel PowerMac, Aluminium PowerBooks, ...)
	  to be probed before the ATA/66 and ATA/33 controllers. Without
	  these, those machine used to have the hard disk on hdc and the
	  CD-ROM on hda. This option changes this to more natural hda for
	  hard disk and hdc for CD-ROM.

config BLK_DEV_IDE_AU1XXX
       bool "IDE for AMD Alchemy Au1200"
       depends on SOC_AU1200
       select IDE_XFER_MODE
choice
       prompt "IDE Mode for AMD Alchemy Au1200"
       default CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
       depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX

config BLK_DEV_IDE_AU1XXX_PIO_DBDMA
       bool "PIO+DbDMA IDE for AMD Alchemy Au1200"

config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
       bool "MDMA2+DbDMA IDE for AMD Alchemy Au1200"
       depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
endchoice

config BLK_DEV_IDE_TX4938
	tristate "TX4938 internal IDE support"
	depends on SOC_TX4938
	select IDE_TIMINGS

config BLK_DEV_IDE_TX4939
	tristate "TX4939 internal IDE support"
	depends on SOC_TX4939
	select BLK_DEV_IDEDMA_SFF

config BLK_DEV_IDE_AT91
	tristate "Atmel AT91 (SAM9, CAP9, AT572D940HF) IDE support"
	depends on ARM && ARCH_AT91 && !ARCH_AT91RM9200 && !ARCH_AT91X40
	select IDE_TIMINGS

config BLK_DEV_IDE_ICSIDE
	tristate "ICS IDE interface support"
	depends on ARM && ARCH_ACORN
	help
	  On Acorn systems, say Y here if you wish to use the ICS IDE
	  interface card.  This is not required for ICS partition support.
	  If you are unsure, say N to this.

config BLK_DEV_IDEDMA_ICS
	bool "ICS DMA support"
	depends on BLK_DEV_IDE_ICSIDE
	help
	  Say Y here if you want to add DMA (Direct Memory Access) support to
	  the ICS IDE driver.

config BLK_DEV_IDE_RAPIDE
	tristate "RapIDE interface support"
	depends on ARM && ARCH_ACORN
	help
	  Say Y here if you want to support the Yellowstone RapIDE controller
	  manufactured for use with Acorn computers.

config IDE_H8300
	tristate "H8300 IDE support"
	depends on H8300
	default y
	help
	  Enables the H8300 IDE driver.

config BLK_DEV_GAYLE
	tristate "Amiga Gayle IDE interface support"
	depends on AMIGA
	help
	  This is the IDE driver for the Amiga Gayle IDE interface. It supports
	  both the `A1200 style' and `A4000 style' of the Gayle IDE interface,
	  This includes on-board IDE interfaces on some Amiga models (A600,
	  A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion
	  bus (M-Tech E-Matrix 530 expansion card).

	  It also provides support for the so-called `IDE doublers' (made
	  by various manufacturers, e.g. Eyetech) that can be connected to
	  the on-board IDE interface of some Amiga models. Using such an IDE
	  doubler, you can connect up to four instead of two IDE devices to
	  the Amiga's on-board IDE interface. The feature is enabled at kernel
	  runtime using the "gayle.doubler" kernel boot parameter.

	  Say Y if you have an Amiga with a Gayle IDE interface and want to use
	  IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
	  it.

	  Note that you also have to enable Zorro bus support if you want to
	  use Gayle IDE interfaces on the Zorro expansion bus.

config BLK_DEV_BUDDHA
	tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
	depends on ZORRO && EXPERIMENTAL
	help
	  This is the IDE driver for the IDE interfaces on the Buddha, Catweasel
	  and X-Surf expansion boards.  It supports up to two interfaces on the
	  Buddha, three on the Catweasel and two on the X-Surf.

	  Say Y if you have a Buddha or Catweasel expansion board and want to
	  use IDE devices (hard disks, CD-ROM drives, etc.) that are connected
	  to one of its IDE interfaces.

config BLK_DEV_FALCON_IDE
	tristate "Falcon IDE interface support"
	depends on ATARI
	help
	  This is the IDE driver for the on-board IDE interface on the Atari
	  Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
	  disks, CD-ROM drives, etc.) that are connected to the on-board IDE
	  interface.

config BLK_DEV_MAC_IDE
	tristate "Macintosh Quadra/Powerbook IDE interface support"
	depends on MAC
	help
	  This is the IDE driver for the on-board IDE interface on some m68k
	  Macintosh models. It supports both the `Quadra style' (used in
	  Quadra/ Centris 630 and Performa 588 models) and `Powerbook style'
	  (used in the Powerbook 150 and 190 models) IDE interface.

	  Say Y if you have such an Macintosh model and want to use IDE
	  devices (hard disks, CD-ROM drives, etc.) that are connected to the
	  on-board IDE interface.

config BLK_DEV_Q40IDE
	tristate "Q40/Q60 IDE interface support"
	depends on Q40
	help
	  Enable the on-board IDE controller in the Q40/Q60.  This should
	  normally be on; disable it only if you are running a custom hard
	  drive subsystem through an expansion card.

config BLK_DEV_PALMCHIP_BK3710
	tristate "Palmchip bk3710 IDE controller support"
	depends on ARCH_DAVINCI
	select IDE_TIMINGS
	select BLK_DEV_IDEDMA_SFF
	help
	  Say Y here if you want to support the onchip IDE controller on the
	  TI DaVinci SoC

# no isa -> no vlb
if ISA && (ALPHA || X86 || MIPS)

comment "Other IDE chipsets support"
comment "Note: most of these also require special kernel boot parameters"

config BLK_DEV_4DRIVES
	tristate "Generic 4 drives/port support"
	help
	  Certain older chipsets, including the Tekram 690CD, use a single set
	  of I/O ports at 0x1f0 to control up to four drives, instead of the
	  customary two drives per port. Support for this can be enabled at
	  runtime using the "ide-4drives.probe" kernel boot parameter if you
	  say Y here.

config BLK_DEV_ALI14XX
	tristate "ALI M14xx support"
	select IDE_TIMINGS
	select IDE_LEGACY
	help
	  This driver is enabled at runtime using the "ali14xx.probe" kernel
	  boot parameter.  It enables support for the secondary IDE interface
	  of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
	  I/O speeds to be set as well.
	  See the files <file:Documentation/ide/ide.txt> and
	  <file:drivers/ide/legacy/ali14xx.c> for more info.

config BLK_DEV_DTC2278
	tristate "DTC-2278 support"
	select IDE_XFER_MODE
	select IDE_LEGACY
	help
	  This driver is enabled at runtime using the "dtc2278.probe" kernel
	  boot parameter. It enables support for the secondary IDE interface
	  of the DTC-2278 card, and permits faster I/O speeds to be set as
	  well. See the <file:Documentation/ide/ide.txt> and
	  <file:drivers/ide/legacy/dtc2278.c> files for more info.

config BLK_DEV_HT6560B
	tristate "Holtek HT6560B support"
	select IDE_TIMINGS
	select IDE_LEGACY
	help
	  This driver is enabled at runtime using the "ht6560b.probe" kernel
	  boot parameter. It enables support for the secondary IDE interface
	  of the Holtek card, and permits faster I/O speeds to be set as well.
	  See the <file:Documentation/ide/ide.txt> and
	  <file:drivers/ide/legacy/ht6560b.c> files for more info.

config BLK_DEV_QD65XX
	tristate "QDI QD65xx support"
	select IDE_TIMINGS
	select IDE_LEGACY
	help
	  This driver is enabled at runtime using the "qd65xx.probe" kernel
	  boot parameter.  It permits faster I/O speeds to be set.  See the
	  <file:Documentation/ide/ide.txt> and <file:drivers/ide/legacy/qd65xx.c>
	  for more info.

config BLK_DEV_UMC8672
	tristate "UMC-8672 support"
	select IDE_XFER_MODE
	select IDE_LEGACY
	help
	  This driver is enabled at runtime using the "umc8672.probe" kernel
	  boot parameter. It enables support for the secondary IDE interface
	  of the UMC-8672, and permits faster I/O speeds to be set as well.
	  See the files <file:Documentation/ide/ide.txt> and
	  <file:drivers/ide/legacy/umc8672.c> for more info.

endif

config BLK_DEV_IDEDMA
	def_bool BLK_DEV_IDEDMA_SFF || \
		 BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
	select IDE_XFER_MODE

endif # IDE