linux-vybrid_public/drivers/net/Kconfig

#
# Network device configuration
#

config HAVE_NET_MACB
	bool

menuconfig NETDEVICES
	default y if UML
	depends on NET
	bool "Network device support"
	---help---
	  You can say N here if you don't intend to connect your Linux box to
	  any other computer at all.

	  You'll have to say Y if your computer contains a network card that
	  you want to use under Linux. If you are going to run SLIP or PPP over
	  telephone line or null modem cable you need say Y here. Connecting
	  two machines with parallel ports using PLIP needs this, as well as
	  AX.25/KISS for sending Internet traffic over amateur radio links.

	  See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	  Terry Dawson. Available at <http://www.tldp.org/guides.html>.

	  If unsure, say Y.

# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES

config IFB
	tristate "Intermediate Functional Block support"
	depends on NET_CLS_ACT
	---help---
	  This is an intermediate driver that allows sharing of
	  resources.
	  To compile this driver as a module, choose M here: the module
	  will be called ifb.  If you want to use more than one ifb
	  device at a time, you need to compile this driver as a module.
	  Instead of 'ifb', the devices will then be called 'ifb0',
	  'ifb1' etc.
	  Look at the iproute2 documentation directory for usage etc

config DUMMY
	tristate "Dummy net driver support"
	---help---
	  This is essentially a bit-bucket device (i.e. traffic you send to
	  this device is consigned into oblivion) with a configurable IP
	  address. It is most commonly used in order to make your currently
	  inactive SLIP address seem like a real address for local programs.
	  If you use SLIP or PPP, you might want to say Y here. Since this
	  thing often comes in handy, the default is Y. It won't enlarge your
	  kernel either. What a deal. Read about it in the Network
	  Administrator's Guide, available from
	  <http://www.tldp.org/docs.html#guide>.

	  To compile this driver as a module, choose M here: the module
	  will be called dummy.  If you want to use more than one dummy
	  device at a time, you need to compile this driver as a module.
	  Instead of 'dummy', the devices will then be called 'dummy0',
	  'dummy1' etc.

config BONDING
	tristate "Bonding driver support"
	depends on INET
	depends on IPV6 || IPV6=n
	---help---
	  Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	  Channels together. This is called 'Etherchannel' by Cisco,
	  'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.

	  The driver supports multiple bonding modes to allow for both high
	  performance and high availability operation.

	  Refer to <file:Documentation/networking/bonding.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called bonding.

config MACVLAN
	tristate "MAC-VLAN support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	---help---
	  This allows one to create virtual interfaces that map packets to
	  or from specific MAC addresses to a particular interface.

	  Macvlan devices can be added using the "ip" command from the
	  iproute2 package starting with the iproute2-2.6.23 release:

	  "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"

	  To compile this driver as a module, choose M here: the module
	  will be called macvlan.

config MACVTAP
	tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
	depends on MACVLAN
	help
	  This adds a specialized tap character device driver that is based
	  on the MAC-VLAN network interface, called macvtap. A macvtap device
	  can be added in the same way as a macvlan device, using 'type
	  macvlan', and then be accessed through the tap user space interface.

	  To compile this driver as a module, choose M here: the module
	  will be called macvtap.

config EQUALIZER
	tristate "EQL (serial line load balancing) support"
	---help---
	  If you have two serial connections to some other computer (this
	  usually requires two modems and two telephone lines) and you use
	  SLIP (the protocol for sending Internet traffic over telephone
	  lines) or PPP (a better SLIP) on them, you can make them behave like
	  one double speed connection using this driver.  Naturally, this has
	  to be supported at the other end as well, either with a similar EQL
	  Linux driver or with a Livingston Portmaster 2e.

	  Say Y if you want this and read
	  <file:Documentation/networking/eql.txt>.  You may also want to read
	  section 6.2 of the NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the module
	  will be called eql.  If unsure, say N.

config TUN
	tristate "Universal TUN/TAP device driver support"
	select CRC32
	---help---
	  TUN/TAP provides packet reception and transmission for user space
	  programs.  It can be viewed as a simple Point-to-Point or Ethernet
	  device, which instead of receiving packets from a physical media,
	  receives them from user space program and instead of sending packets
	  via physical media writes them to the user space program.

	  When a program opens /dev/net/tun, driver creates and registers
	  corresponding net device tunX or tapX.  After a program closed above
	  devices, driver will automatically delete tunXX or tapXX device and
	  all routes corresponding to it.

	  Please read <file:Documentation/networking/tuntap.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called tun.

	  If you don't know what to use this for, you don't need it.

config VETH
	tristate "Virtual ethernet pair device"
	---help---
	  This device is a local ethernet tunnel. Devices are created in pairs.
	  When one end receives the packet it appears on its pair and vice
	  versa.

config NET_SB1000
	tristate "General Instruments Surfboard 1000"
	depends on PNP
	---help---
	  This is a driver for the General Instrument (also known as
	  NextLevel) SURFboard 1000 internal
	  cable modem. This is an ISA card which is used by a number of cable
	  TV companies to provide cable modem access. It's a one-way
	  downstream-only cable modem, meaning that your upstream net link is
	  provided by your regular phone modem.

	  At present this driver only compiles as a module, so say M here if
	  you have this card. The module will be called sb1000. Then read
	  <file:Documentation/networking/README.sb1000> for information on how
	  to use this module, as it needs special ppp scripts for establishing
	  a connection. Further documentation and the necessary scripts can be
	  found at:

	  <http://www.jacksonville.net/~fventuri/>
	  <http://home.adelphia.net/~siglercm/sb1000.html>
	  <http://linuxpower.cx/~cable/>

	  If you don't have this card, of course say N.

source "drivers/net/arcnet/Kconfig"

config MII
	tristate "Generic Media Independent Interface device support"
	help
	  Most ethernet controllers have MII transceiver either as an external
	  or internal device.  It is safe to say Y or M here even if your
	  ethernet card lacks MII.

source "drivers/net/phy/Kconfig"

#
#	Ethernet
#

source "drivers/net/ethernet/Kconfig"

menuconfig NET_ETHERNET
	bool "Ethernet (10 or 100Mbit)"
	depends on !UML
	---help---
	  Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
	  type of Local Area Network (LAN) in universities and companies.

	  Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
	  coaxial cable, linking computers in a chain), 10BASE-T or twisted
	  pair (10 Mbps over twisted pair cable, linking computers to central
	  hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
	  100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
	  100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
	  cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
	  [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
	  Ethernet (1 Gbps over optical fiber or short copper links).

	  If your Linux machine will be connected to an Ethernet and you have
	  an Ethernet network interface card (NIC) installed in your computer,
	  say Y here and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. You will then also have
	  to say Y to the driver for your particular NIC.

	  Note that the answer to this question won't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about Ethernet network cards. If unsure, say N.

if NET_ETHERNET

config MACB
	tristate "Atmel MACB support"
	depends on HAVE_NET_MACB
	select PHYLIB
	help
	  The Atmel MACB ethernet interface is found on many AT32 and AT91
	  parts. Say Y to include support for the MACB chip.

	  To compile this driver as a module, choose M here: the module
	  will be called macb.

source "drivers/net/arm/Kconfig"

config KORINA
	tristate "Korina (IDT RC32434) Ethernet support"
	depends on NET_ETHERNET && MIKROTIK_RB532
	help
	  If you have a Mikrotik RouterBoard 500 or IDT RC32434
	  based system say Y. Otherwise say N.

config MIPS_SIM_NET
	tristate "MIPS simulator Network device"
	depends on MIPS_SIM
	help
	  The MIPSNET device is a simple Ethernet network device which is
	  emulated by the MIPS Simulator.
	  If you are not using a MIPSsim or are unsure, say N.

config SH_ETH
	tristate "Renesas SuperH Ethernet support"
	depends on SUPERH && \
		(CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \
		 CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \
		 CPU_SUBTYPE_SH7724 || CPU_SUBTYPE_SH7757)
	select CRC32
	select MII
	select MDIO_BITBANG
	select PHYLIB
	help
	  Renesas SuperH Ethernet device driver.
	  This driver supporting CPUs are:
		- SH7710, SH7712, SH7763, SH7619, SH7724, and SH7757.

config BFIN_MAC
	tristate "Blackfin on-chip MAC support"
	depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
	select CRC32
	select MII
	select PHYLIB
	select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
	help
	  This is the driver for Blackfin on-chip mac device. Say Y if you want it
	  compiled into the kernel. This driver is also available as a module
	  ( = code which can be inserted in and removed from the running kernel
	  whenever you want). The module will be called bfin_mac.

config BFIN_MAC_USE_L1
	bool "Use L1 memory for rx/tx packets"
	depends on BFIN_MAC && (BF527 || BF537)
	default y
	help
	  To get maximum network performance, you should use L1 memory as rx/tx buffers.
	  Say N here if you want to reserve L1 memory for other uses.

config BFIN_TX_DESC_NUM
	int "Number of transmit buffer packets"
	depends on BFIN_MAC
	range 6 10 if BFIN_MAC_USE_L1
	range 10 100
	default "10"
	help
	  Set the number of buffer packets used in driver.

config BFIN_RX_DESC_NUM
	int "Number of receive buffer packets"
	depends on BFIN_MAC
	range 20 100 if BFIN_MAC_USE_L1
	range 20 800
	default "20"
	help
	  Set the number of buffer packets used in driver.

config BFIN_MAC_USE_HWSTAMP
	bool "Use IEEE 1588 hwstamp"
	depends on BFIN_MAC && BF518
	default y
	help
	  To support the IEEE 1588 Precision Time Protocol (PTP), select y here

config NET_NETX
	tristate "NetX Ethernet support"
	select MII
	depends on ARCH_NETX
	help
	  This is support for the Hilscher netX builtin Ethernet ports

	  To compile this driver as a module, choose M here. The module
	  will be called netx-eth.

config TI_DAVINCI_EMAC
	tristate "TI DaVinci EMAC Support"
	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
	select TI_DAVINCI_MDIO
	select TI_DAVINCI_CPDMA
	select PHYLIB
	help
	  This driver supports TI's DaVinci Ethernet .

	  To compile this driver as a module, choose M here: the module
	  will be called davinci_emac_driver.  This is recommended.

config TI_DAVINCI_MDIO
	tristate "TI DaVinci MDIO Support"
	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
	select PHYLIB
	help
	  This driver supports TI's DaVinci MDIO module.

	  To compile this driver as a module, choose M here: the module
	  will be called davinci_mdio.  This is recommended.

config TI_DAVINCI_CPDMA
	tristate "TI DaVinci CPDMA Support"
	depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
	help
	  This driver supports TI's DaVinci CPDMA dma engine.

	  To compile this driver as a module, choose M here: the module
	  will be called davinci_cpdma.  This is recommended.

config DM9000
	tristate "DM9000 support"
	depends on ARM || BLACKFIN || MIPS
	select CRC32
	select MII
	---help---
	  Support for DM9000 chipset.

	  To compile this driver as a module, choose M here.  The module
	  will be called dm9000.

config DM9000_DEBUGLEVEL
	int "DM9000 maximum debug level"
	depends on DM9000
	default 4
	help
	  The maximum level of debugging code compiled into the DM9000
	  driver.

config DM9000_FORCE_SIMPLE_PHY_POLL
	bool "Force simple NSR based PHY polling"
	depends on DM9000
	---help---
	  This configuration forces the DM9000 to use the NSR's LinkStatus
	  bit to determine if the link is up or down instead of the more
	  costly MII PHY reads. Note, this will not work if the chip is
	  operating with an external PHY.

config ENC28J60
	tristate "ENC28J60 support"
	depends on EXPERIMENTAL && SPI && NET_ETHERNET
	select CRC32
	---help---
	  Support for the Microchip EN28J60 ethernet chip.

	  To compile this driver as a module, choose M here. The module will be
	  called enc28j60.

config ENC28J60_WRITEVERIFY
	bool "Enable write verify"
	depends on ENC28J60
	---help---
	  Enable the verify after the buffer write useful for debugging purpose.
	  If unsure, say N.

config ETHOC
	tristate "OpenCores 10/100 Mbps Ethernet MAC support"
	depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
	select MII
	select PHYLIB
	select CRC32
	select BITREVERSE
	help
	  Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.

config GRETH
	tristate "Aeroflex Gaisler GRETH Ethernet MAC support"
	depends on SPARC
	select PHYLIB
	select CRC32
	help
	  Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC.

config DNET
	tristate "Dave ethernet support (DNET)"
	depends on NET_ETHERNET && HAS_IOMEM
	select PHYLIB
	help
	  The Dave ethernet interface (DNET) is found on Qong Board FPGA.
	  Say Y to include support for the DNET chip.

	  To compile this driver as a module, choose M here: the module
	  will be called dnet.

config AT1700
	tristate "AT1700/1720 support (EXPERIMENTAL)"
	depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
	select CRC32
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here. The module
	  will be called at1700.

config HP100
	tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
	depends on ISA || EISA || PCI
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here. The module
	  will be called hp100.

config NET_ISA
	bool "Other ISA cards"
	depends on ISA
	---help---
	  If your network (Ethernet) card hasn't been mentioned yet and its
	  bus system (that's the way the cards talks to the other components
	  of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
	  Make sure you know the name of your card. Read the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>.

	  If unsure, say Y.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the remaining ISA network card questions. If you say Y, you will be
	  asked for your specific card in the following questions.

config ETH16I
	tristate "ICL EtherTeam 16i/32 support"
	depends on NET_ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here. The module
	  will be called eth16i.

config NET_PCI
	bool "EISA, VLB, PCI and on board controllers"
	depends on ISA || EISA || PCI
	help
	  This is another class of network cards which attach directly to the
	  bus. If you have one of those, say Y and read the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about this class of network cards. If you say Y, you
	  will be asked for your specific card in the following questions. If
	  you are unsure, say Y.

config ADAPTEC_STARFIRE
	tristate "Adaptec Starfire/DuraLAN support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
	  adapter. The DuraLAN chip is used on the 64 bit PCI boards from
	  Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
	  driver.

	  To compile this driver as a module, choose M here: the module
	  will be called starfire.  This is recommended.

config KSZ884X_PCI
	tristate "Micrel KSZ8841/2 PCI"
	depends on NET_PCI && PCI
	select MII
	select CRC32
	help
	  This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.

	  To compile this driver as a module, choose M here. The module
	  will be called ksz884x.

config FORCEDETH
	tristate "nForce Ethernet support"
	depends on NET_PCI && PCI
	help
	  If you have a network (Ethernet) controller of this type, say Y and
	  read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here. The module
	  will be called forcedeth.

config TC35815
	tristate "TOSHIBA TC35815 Ethernet support"
	depends on NET_PCI && PCI && MIPS
	select PHYLIB

config FEALNX
	tristate "Myson MTD-8xx PCI Ethernet support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  Say Y here to support the Myson MTD-800 family of PCI-based Ethernet 
	  cards. <http://www.myson.com.tw/>

config R6040
	tristate "RDC R6040 Fast Ethernet Adapter support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	select PHYLIB
	help
	  This is a driver for the R6040 Fast Ethernet MACs found in the
	  the RDC R-321x System-on-chips.

	  To compile this driver as a module, choose M here: the module
	  will be called r6040. This is recommended.

config SIS900
	tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	---help---
	  This is a driver for the Fast Ethernet PCI network cards based on
	  the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
	  SiS 630 and SiS 540 chipsets.

	  This driver also supports AMD 79C901 HomePNA so that you can use
	  your phone line as a network cable.

	  To compile this driver as a module, choose M here: the module
	  will be called sis900.  This is recommended.

config TLAN
	tristate "TI ThunderLAN support"
	depends on NET_PCI && (PCI || EISA)
	---help---
	  If you have a PCI Ethernet network card based on the ThunderLAN chip
	  which is supported by this driver, say Y and read the
	  Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  Devices currently supported by this driver are Compaq Netelligent,
	  Compaq NetFlex and Olicom cards.  Please read the file
	  <file:Documentation/networking/tlan.txt> for more details.

	  To compile this driver as a module, choose M here. The module
	  will be called tlan.

	  Please email feedback to <torben.mathiasen@compaq.com>.

config KS8842
	tristate "Micrel KSZ8841/42 with generic bus interface"
	depends on HAS_IOMEM && DMA_ENGINE
	help
	  This platform driver is for KSZ8841(1-port) / KS8842(2-port)
	  ethernet switch chip (managed, VLAN, QoS) from Micrel or
	  Timberdale(FPGA).

config KS8851
	tristate "Micrel KS8851 SPI"
	depends on SPI
	select MII
	select CRC32
	help
	  SPI driver for Micrel KS8851 SPI attached network chip.

config KS8851_MLL
	tristate "Micrel KS8851 MLL"
	depends on HAS_IOMEM
	select MII
	help
	  This platform driver is for Micrel KS8851 Address/data bus
	  multiplexed network chip.

config VIA_RHINE
	tristate "VIA Rhine support"
	depends on NET_PCI && PCI
	select CRC32
	select MII
	help
	  If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
	  Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
	  Ethernet functions can also be found integrated on South Bridges
	  (e.g. VT8235).

	  To compile this driver as a module, choose M here. The module
	  will be called via-rhine.

config VIA_RHINE_MMIO
	bool "Use MMIO instead of PIO"
	depends on VIA_RHINE
	help
	  This instructs the driver to use PCI shared memory (MMIO) instead of
	  programmed I/O ports (PIO). Enabling this gives an improvement in
	  processing time in parts of the driver.

	  If unsure, say Y.

config CPMAC
	tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
	depends on NET_ETHERNET && EXPERIMENTAL && AR7
	select PHYLIB
	help
	  TI AR7 CPMAC Ethernet support

config NET_POCKET
	bool "Pocket and portable adapters"
	depends on PARPORT
	---help---
	  Cute little network (Ethernet) devices which attach to the parallel
	  port ("pocket adapters"), commonly used with laptops. If you have
	  one of those, say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  If you want to plug a network (or some other) card into the PCMCIA
	  (or PC-card) slot of your laptop instead (PCMCIA is the standard for
	  credit card size extension cards used by all modern laptops), you
	  need the pcmcia-cs package (location contained in the file
	  <file:Documentation/Changes>) and you can say N here.

	  Laptop users should read the Linux Laptop home page at
	  <http://www.linux-on-laptops.com/> or
	  Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about this class of network devices. If you say Y, you
	  will be asked for your specific device in the following questions.

config FEC
	bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
	depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
		IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC
	default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM
	select PHYLIB
	help
	  Say Y here if you want to use the built-in 10/100 Fast ethernet
	  controller on some Motorola ColdFire and Freescale i.MX processors.

config FEC_MPC52xx
	tristate "MPC52xx FEC driver"
	depends on PPC_MPC52xx && PPC_BESTCOMM
	select CRC32
	select PHYLIB
	select PPC_BESTCOMM_FEC
	---help---
	  This option enables support for the MPC5200's on-chip
	  Fast Ethernet Controller
	  If compiled as module, it will be called fec_mpc52xx.

config FEC_MPC52xx_MDIO
	bool "MPC52xx FEC MDIO bus driver"
	depends on FEC_MPC52xx
	default y
	---help---
	  The MPC5200's FEC can connect to the Ethernet either with
	  an external MII PHY chip or 10 Mbps 7-wire interface
	  (Motorola? industry standard).
	  If your board uses an external PHY connected to FEC, enable this.
	  If not sure, enable.
	  If compiled as module, it will be called fec_mpc52xx_phy.

config XILINX_EMACLITE
	tristate "Xilinx 10/100 Ethernet Lite support"
	depends on PPC32 || MICROBLAZE
	select PHYLIB
	help
	  This driver supports the 10/100 Ethernet Lite from Xilinx.

config LANTIQ_ETOP
	tristate "Lantiq SoC ETOP driver"
	depends on SOC_TYPE_XWAY
	help
	  Support for the MII0 inside the Lantiq SoC


source "drivers/net/fs_enet/Kconfig"

source "drivers/net/octeon/Kconfig"

endif # NET_ETHERNET

#
#	Gigabit Ethernet
#

menuconfig NETDEV_1000
	bool "Ethernet (1000 Mbit)"
	depends on !UML
	default y
	---help---
	  Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
	  type of Local Area Network (LAN) in universities and companies.

	  Say Y here to get to see options for Gigabit Ethernet drivers.
	  This option alone does not add any kernel code.
	  Note that drivers supporting both 100 and 1000 MBit may be listed
	  under "Ethernet (10 or 100MBit)" instead.

	  If you say N, all options in this submenu will be skipped and disabled.

if NETDEV_1000

config IP1000
	tristate "IP1000 Gigabit Ethernet support"
	depends on PCI && EXPERIMENTAL
	select MII
	---help---
	  This driver supports IP1000 gigabit Ethernet cards.

	  To compile this driver as a module, choose M here: the module
	  will be called ipg.  This is recommended.

config HAMACHI
	tristate "Packet Engines Hamachi GNIC-II support"
	depends on PCI
	select MII
	help
	  If you have a Gigabit Ethernet card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here. The module will be
	  called hamachi.

config YELLOWFIN
	tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
	depends on PCI && EXPERIMENTAL
	select CRC32
	---help---
	  Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
	  adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
	  used by the Beowulf Linux cluster project.  See
	  <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
	  information about this driver in particular and Beowulf in general.

	  To compile this driver as a module, choose M here: the module
	  will be called yellowfin.  This is recommended.

config SIS190
	tristate "SiS190/SiS191 gigabit ethernet support"
	depends on PCI
	select CRC32
	select MII
	---help---
	  Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
	  a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
	  appear in lan on motherboard designs which are based on SiS 965
	  and SiS 966 south bridge.

	  To compile this driver as a module, choose M here: the module
	  will be called sis190.  This is recommended.

config VIA_VELOCITY
	tristate "VIA Velocity support"
	depends on PCI
	select CRC32
	select CRC_CCITT
	select MII
	help
	  If you have a VIA "Velocity" based network card say Y here.

	  To compile this driver as a module, choose M here. The module
	  will be called via-velocity.

config SPIDER_NET
	tristate "Spider Gigabit Ethernet driver"
	depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
	select FW_LOADER
	select SUNGEM_PHY
	help
	  This driver supports the Gigabit Ethernet chips present on the
	  Cell Processor-Based Blades from IBM.

config TSI108_ETH
	tristate "Tundra TSI108 gigabit Ethernet support"
	depends on TSI108_BRIDGE
	help
	  This driver supports Tundra TSI108 gigabit Ethernet ports.
	  To compile this driver as a module, choose M here: the module
	  will be called tsi108_eth.

config GELIC_NET
	tristate "PS3 Gigabit Ethernet driver"
	depends on PPC_PS3
	select PS3_SYS_MANAGER
	help
	  This driver supports the network device on the PS3 game
	  console.  This driver has built-in support for Ethernet.

	  To compile this driver as a module, choose M here: the
	  module will be called ps3_gelic.

config GELIC_WIRELESS
	bool "PS3 Wireless support"
	depends on WLAN
	depends on GELIC_NET
	select WIRELESS_EXT
	help
	  This option adds the support for the wireless feature of PS3.
	  If you have the wireless-less model of PS3 or have no plan to
	  use wireless feature, disabling this option saves memory.  As
	  the driver automatically distinguishes the models, you can
	  safely enable this option even if you have a wireless-less model.

config FSL_PQ_MDIO
	tristate "Freescale PQ MDIO"
	depends on FSL_SOC
	select PHYLIB
	help
	  This driver supports the MDIO bus used by the gianfar and UCC drivers.

config GIANFAR
	tristate "Gianfar Ethernet"
	depends on FSL_SOC
	select FSL_PQ_MDIO
	select PHYLIB
	select CRC32
	help
	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
	  and MPC86xx family of chips, and the FEC on the 8540.

config UCC_GETH
	tristate "Freescale QE Gigabit Ethernet"
	depends on QUICC_ENGINE
	select FSL_PQ_MDIO
	select PHYLIB
	help
	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
	  which is available on some Freescale SOCs.

config UGETH_TX_ON_DEMAND
	bool "Transmit on Demand support"
	depends on UCC_GETH

config XILINX_LL_TEMAC
	tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
	depends on PPC || MICROBLAZE
	select PHYLIB
	help
	  This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
	  core used in Xilinx Spartan and Virtex FPGAs

config JME
	tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
	depends on PCI
	select CRC32
	select MII
	---help---
	  This driver supports the PCI-Express gigabit ethernet adapters
	  based on JMicron JMC250 chipset.

	  To compile this driver as a module, choose M here. The module
	  will be called jme.

config S6GMAC
	tristate "S6105 GMAC ethernet support"
	depends on XTENSA_VARIANT_S6000
	select PHYLIB
	help
	  This driver supports the on chip ethernet device on the
	  S6105 xtensa processor.

	  To compile this driver as a module, choose M here. The module
	  will be called s6gmac.

endif # NETDEV_1000

#
#	10 Gigabit Ethernet
#

menuconfig NETDEV_10000
	bool "Ethernet (10000 Mbit)"
	depends on !UML
	default y
	---help---
	  Say Y here to get to see options for 10 Gigabit Ethernet drivers.
	  This option alone does not add any kernel code.

	  If you say N, all options in this submenu will be skipped and disabled.

if NETDEV_10000

config MDIO
	tristate

config SUNGEM_PHY
	tristate

endif # NETDEV_10000

source "drivers/net/tokenring/Kconfig"

source "drivers/net/wireless/Kconfig"

source "drivers/net/wimax/Kconfig"

source "drivers/net/usb/Kconfig"

source "drivers/net/pcmcia/Kconfig"

source "drivers/net/wan/Kconfig"

source "drivers/atm/Kconfig"

source "drivers/ieee802154/Kconfig"

source "drivers/s390/net/Kconfig"

source "drivers/net/caif/Kconfig"

config TILE_NET
	tristate "Tilera GBE/XGBE network driver support"
	depends on TILE
	default y
	select CRC32
	help
	  This is a standard Linux network device driver for the
	  on-chip Tilera Gigabit Ethernet and XAUI interfaces.

	  To compile this driver as a module, choose M here: the module
	  will be called tile_net.

config XEN_NETDEV_FRONTEND
	tristate "Xen network device frontend driver"
	depends on XEN
	select XEN_XENBUS_FRONTEND
	default y
	help
	  This driver provides support for Xen paravirtual network
	  devices exported by a Xen network driver domain (often
	  domain 0).

	  The corresponding Linux backend driver is enabled by the
	  CONFIG_XEN_NETDEV_BACKEND option.

	  If you are compiling a kernel for use as Xen guest, you
	  should say Y here. To compile this driver as a module, chose
	  M here: the module will be called xen-netfront.

config XEN_NETDEV_BACKEND
	tristate "Xen backend network device"
	depends on XEN_BACKEND
	help
	  This driver allows the kernel to act as a Xen network driver
	  domain which exports paravirtual network devices to other
	  Xen domains. These devices can be accessed by any operating
	  system that implements a compatible front end.

	  The corresponding Linux frontend driver is enabled by the
	  CONFIG_XEN_NETDEV_FRONTEND configuration option.

	  The backend driver presents a standard network device
	  endpoint for each paravirtual network device to the driver
	  domain network stack. These can then be bridged or routed
	  etc in order to provide full network connectivity.

	  If you are compiling a kernel to run in a Xen network driver
	  domain (often this is domain 0) you should say Y here. To
	  compile this driver as a module, chose M here: the module
	  will be called xen-netback.

config RIONET
	tristate "RapidIO Ethernet over messaging driver support"
	depends on RAPIDIO

config RIONET_TX_SIZE
	int "Number of outbound queue entries"
	depends on RIONET
	default "128"

config RIONET_RX_SIZE
	int "Number of inbound queue entries"
	depends on RIONET
	default "128"

config FDDI
	tristate "FDDI driver support"
	depends on (PCI || EISA || TC)
	help
	  Fiber Distributed Data Interface is a high speed local area network
	  design; essentially a replacement for high speed Ethernet. FDDI can
	  run over copper or fiber. If you are connected to such a network and
	  want a driver for the FDDI card in your computer, say Y here (and
	  then also Y to the driver for your FDDI card, below). Most people
	  will say N.

config DEFXX
	tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
	depends on FDDI && (PCI || EISA || TC)
	---help---
	  This is support for the DIGITAL series of TURBOchannel (DEFTA),
	  EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
	  to a local FDDI network.

	  To compile this driver as a module, choose M here: the module
	  will be called defxx.  If unsure, say N.

config DEFXX_MMIO
	bool
	prompt "Use MMIO instead of PIO" if PCI || EISA
	depends on DEFXX
	default n if PCI || EISA
	default y
	---help---
	  This instructs the driver to use EISA or PCI memory-mapped I/O
	  (MMIO) as appropriate instead of programmed I/O ports (PIO).
	  Enabling this gives an improvement in processing time in parts
	  of the driver, but it may cause problems with EISA (DEFEA)
	  adapters.  TURBOchannel does not have the concept of I/O ports,
	  so MMIO is always used for these (DEFTA) adapters.

	  If unsure, say N.

config SKFP
	tristate "SysKonnect FDDI PCI support"
	depends on FDDI && PCI
	select BITREVERSE
	---help---
	  Say Y here if you have a SysKonnect FDDI PCI adapter.
	  The following adapters are supported by this driver:
	  - SK-5521 (SK-NET FDDI-UP)
	  - SK-5522 (SK-NET FDDI-UP DAS)
	  - SK-5541 (SK-NET FDDI-FP)
	  - SK-5543 (SK-NET FDDI-LP)
	  - SK-5544 (SK-NET FDDI-LP DAS)
	  - SK-5821 (SK-NET FDDI-UP64)
	  - SK-5822 (SK-NET FDDI-UP64 DAS)
	  - SK-5841 (SK-NET FDDI-FP64)
	  - SK-5843 (SK-NET FDDI-LP64)
	  - SK-5844 (SK-NET FDDI-LP64 DAS)
	  - Netelligent 100 FDDI DAS Fibre SC
	  - Netelligent 100 FDDI SAS Fibre SC
	  - Netelligent 100 FDDI DAS UTP
	  - Netelligent 100 FDDI SAS UTP
	  - Netelligent 100 FDDI SAS Fibre MIC

	  Read <file:Documentation/networking/skfp.txt> for information about
	  the driver.

	  Questions concerning this driver can be addressed to:
	  <linux@syskonnect.de>

	  To compile this driver as a module, choose M here: the module
	  will be called skfp.  This is recommended.

config HIPPI
	bool "HIPPI driver support (EXPERIMENTAL)"
	depends on EXPERIMENTAL && INET && PCI
	help
	  HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
	  1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
	  can run over copper (25m) or fiber (300m on multi-mode or 10km on
	  single-mode). HIPPI networks are commonly used for clusters and to
	  connect to super computers. If you are connected to a HIPPI network
	  and have a HIPPI network card in your computer that you want to use
	  under Linux, say Y here (you must also remember to enable the driver
	  for your HIPPI card below). Most people will say N here.

config ROADRUNNER
	tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
	depends on HIPPI && PCI
	help
	  Say Y here if this is your PCI HIPPI network card.

	  To compile this driver as a module, choose M here: the module
	  will be called rrunner.  If unsure, say N.

config ROADRUNNER_LARGE_RINGS
	bool "Use large TX/RX rings (EXPERIMENTAL)"
	depends on ROADRUNNER
	help
	  If you say Y here, the RoadRunner driver will preallocate up to 2 MB
	  of additional memory to allow for fastest operation, both for
	  transmitting and receiving. This memory cannot be used by any other
	  kernel code or by user space programs. Say Y here only if you have
	  the memory.

config PLIP
	tristate "PLIP (parallel port) support"
	depends on PARPORT
	---help---
	  PLIP (Parallel Line Internet Protocol) is used to create a
	  reasonably fast mini network consisting of two (or, rarely, more)
	  local machines.  A PLIP link from a Linux box is a popular means to
	  install a Linux distribution on a machine which doesn't have a
	  CD-ROM drive (a minimal system has to be transferred with floppies
	  first). The kernels on both machines need to have this PLIP option
	  enabled for this to work.

	  The PLIP driver has two modes, mode 0 and mode 1.  The parallel
	  ports (the connectors at the computers with 25 holes) are connected
	  with "null printer" or "Turbo Laplink" cables which can transmit 4
	  bits at a time (mode 0) or with special PLIP cables, to be used on
	  bidirectional parallel ports only, which can transmit 8 bits at a
	  time (mode 1); you can find the wiring of these cables in
	  <file:Documentation/networking/PLIP.txt>.  The cables can be up to
	  15m long.  Mode 0 works also if one of the machines runs DOS/Windows
	  and has some PLIP software installed, e.g. the Crynwr PLIP packet
	  driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
	  and winsock or NCSA's telnet.

	  If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
	  as the NET-3-HOWTO, both available from
	  <http://www.tldp.org/docs.html#howto>.  Note that the PLIP
	  protocol has been changed and this PLIP driver won't work together
	  with the PLIP support in Linux versions 1.0.x.  This option enlarges
	  your kernel by about 8 KB.

	  To compile this driver as a module, choose M here. The module
	  will be called plip. If unsure, say Y or M, in case you buy
	  a laptop later.

config PPP
	tristate "PPP (point-to-point protocol) support"
	select SLHC
	---help---
	  PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
	  the same purpose: sending Internet traffic over telephone (and other
	  serial) lines.  Ask your access provider if they support it, because
	  otherwise you can't use it; most Internet access providers these
	  days support PPP rather than SLIP.

	  To use PPP, you need an additional program called pppd as described
	  in the PPP-HOWTO, available at
	  <http://www.tldp.org/docs.html#howto>.  Make sure that you have
	  the version of pppd recommended in <file:Documentation/Changes>.
	  The PPP option enlarges your kernel by about 16 KB.

	  There are actually two versions of PPP: the traditional PPP for
	  asynchronous lines, such as regular analog phone lines, and
	  synchronous PPP which can be used over digital ISDN lines for
	  example.  If you want to use PPP over phone lines or other
	  asynchronous serial lines, you need to say Y (or M) here and also to
	  the next option, "PPP support for async serial ports".  For PPP over
	  synchronous lines, you should say Y (or M) here and to "Support
	  synchronous PPP", below.

	  If you said Y to "Version information on all symbols" above, then
	  you cannot compile the PPP driver into the kernel; you can then only
	  compile it as a module. To compile this driver as a module, choose M
	  here. The module will be called ppp_generic.

config PPP_MULTILINK
	bool "PPP multilink support (EXPERIMENTAL)"
	depends on PPP && EXPERIMENTAL
	help
	  PPP multilink is a protocol (defined in RFC 1990) which allows you
	  to combine several (logical or physical) lines into one logical PPP
	  connection, so that you can utilize your full bandwidth.

	  This has to be supported at the other end as well and you need a
	  version of the pppd daemon which understands the multilink protocol.

	  If unsure, say N.

config PPP_FILTER
	bool "PPP filtering"
	depends on PPP
	help
	  Say Y here if you want to be able to filter the packets passing over
	  PPP interfaces.  This allows you to control which packets count as
	  activity (i.e. which packets will reset the idle timer or bring up
	  a demand-dialed link) and which packets are to be dropped entirely.
	  You need to say Y here if you wish to use the pass-filter and
	  active-filter options to pppd.

	  If unsure, say N.

config PPP_ASYNC
	tristate "PPP support for async serial ports"
	depends on PPP
	select CRC_CCITT
	---help---
	  Say Y (or M) here if you want to be able to use PPP over standard
	  asynchronous serial ports, such as COM1 or COM2 on a PC.  If you use
	  a modem (not a synchronous or ISDN modem) to contact your ISP, you
	  need this option.

	  To compile this driver as a module, choose M here.

	  If unsure, say Y.

config PPP_SYNC_TTY
	tristate "PPP support for sync tty ports"
	depends on PPP
	help
	  Say Y (or M) here if you want to be able to use PPP over synchronous
	  (HDLC) tty devices, such as the SyncLink adapter. These devices
	  are often used for high-speed leased lines like T1/E1.

	  To compile this driver as a module, choose M here.

config PPP_DEFLATE
	tristate "PPP Deflate compression"
	depends on PPP
	select ZLIB_INFLATE
	select ZLIB_DEFLATE
	---help---
	  Support for the Deflate compression method for PPP, which uses the
	  Deflate algorithm (the same algorithm that gzip uses) to compress
	  each PPP packet before it is sent over the wire.  The machine at the
	  other end of the PPP link (usually your ISP) has to support the
	  Deflate compression method as well for this to be useful.  Even if
	  they don't support it, it is safe to say Y here.

	  To compile this driver as a module, choose M here.

config PPP_BSDCOMP
	tristate "PPP BSD-Compress compression"
	depends on PPP
	---help---
	  Support for the BSD-Compress compression method for PPP, which uses
	  the LZW compression method to compress each PPP packet before it is
	  sent over the wire. The machine at the other end of the PPP link
	  (usually your ISP) has to support the BSD-Compress compression
	  method as well for this to be useful. Even if they don't support it,
	  it is safe to say Y here.

	  The PPP Deflate compression method ("PPP Deflate compression",
	  above) is preferable to BSD-Compress, because it compresses better
	  and is patent-free.

	  Note that the BSD compression code will always be compiled as a
	  module; it is called bsd_comp and will show up in the directory
	  modules once you have said "make modules". If unsure, say N.

config PPP_MPPE
	tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
	depends on PPP && EXPERIMENTAL
	select CRYPTO
	select CRYPTO_SHA1
	select CRYPTO_ARC4
	select CRYPTO_ECB
	---help---
	  Support for the MPPE Encryption protocol, as employed by the
	  Microsoft Point-to-Point Tunneling Protocol.

	  See http://pptpclient.sourceforge.net/ for information on
	  configuring PPTP clients and servers to utilize this method.

config PPPOE
	tristate "PPP over Ethernet (EXPERIMENTAL)"
	depends on EXPERIMENTAL && PPP
	help
	  Support for PPP over Ethernet.

	  This driver requires the latest version of pppd from the CVS
	  repository at cvs.samba.org.  Alternatively, see the 
	  RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
	  which contains instruction on how to use this driver (under 
	  the heading "Kernel mode PPPoE").

config PPTP
	tristate "PPP over IPv4 (PPTP) (EXPERIMENTAL)"
	depends on EXPERIMENTAL && PPP && NET_IPGRE_DEMUX
	help
	  Support for PPP over IPv4.(Point-to-Point Tunneling Protocol)

	  This driver requires pppd plugin to work in client mode or
	  modified pptpd (poptop) to work in server mode.
	  See http://accel-pptp.sourceforge.net/ for information how to
	  utilize this module.

config PPPOATM
	tristate "PPP over ATM"
	depends on ATM && PPP
	help
	  Support PPP (Point to Point Protocol) encapsulated in ATM frames.
	  This implementation does not yet comply with section 8 of RFC2364,
	  which can lead to bad results if the ATM peer loses state and
	  changes its encapsulation unilaterally.

config PPPOL2TP
	tristate "PPP over L2TP (EXPERIMENTAL)"
	depends on EXPERIMENTAL && L2TP && PPP
	help
	  Support for PPP-over-L2TP socket family. L2TP is a protocol
	  used by ISPs and enterprises to tunnel PPP traffic over UDP
	  tunnels. L2TP is replacing PPTP for VPN uses.

config SLIP
	tristate "SLIP (serial line) support"
	---help---
	  Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
	  connect to your Internet service provider or to connect to some
	  other local Unix box or if you want to configure your Linux box as a
	  Slip/CSlip server for other people to dial in. SLIP (Serial Line
	  Internet Protocol) is a protocol used to send Internet traffic over
	  serial connections such as telephone lines or null modem cables;
	  nowadays, the protocol PPP is more commonly used for this same
	  purpose.

	  Normally, your access provider has to support SLIP in order for you
	  to be able to use it, but there is now a SLIP emulator called SLiRP
	  around (available from
	  <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
	  allows you to use SLIP over a regular dial up shell connection. If
	  you plan to use SLiRP, make sure to say Y to CSLIP, below. The
	  NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>, explains how to
	  configure SLIP. Note that you don't need this option if you just
	  want to run term (term is a program which gives you almost full
	  Internet connectivity if you have a regular dial up shell account on
	  some Internet connected Unix computer. Read
	  <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
	  support will enlarge your kernel by about 4 KB. If unsure, say N.

	  To compile this driver as a module, choose M here. The module
	  will be called slip.

config SLIP_COMPRESSED
	bool "CSLIP compressed headers"
	depends on SLIP
	select SLHC
	---help---
	  This protocol is faster than SLIP because it uses compression on the
	  TCP/IP headers (not on the data itself), but it has to be supported
	  on both ends. Ask your access provider if you are not sure and
	  answer Y, just in case. You will still be able to use plain SLIP. If
	  you plan to use SLiRP, the SLIP emulator (available from
	  <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
	  allows you to use SLIP over a regular dial up shell connection, you
	  definitely want to say Y here. The NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>, explains how to configure
	  CSLIP. This won't enlarge your kernel.

config SLHC
	tristate
	help
	  This option enables Van Jacobsen serial line header compression
	  routines.

config SLIP_SMART
	bool "Keepalive and linefill"
	depends on SLIP
	help
	  Adds additional capabilities to the SLIP driver to support the
	  RELCOM line fill and keepalive monitoring. Ideal on poor quality
	  analogue lines.

config SLIP_MODE_SLIP6
	bool "Six bit SLIP encapsulation"
	depends on SLIP
	help
	  Just occasionally you may need to run IP over hostile serial
	  networks that don't pass all control characters or are only seven
	  bit. Saying Y here adds an extra mode you can use with SLIP:
	  "slip6". In this mode, SLIP will only send normal ASCII symbols over
	  the serial device. Naturally, this has to be supported at the other
	  end of the link as well. It's good enough, for example, to run IP
	  over the async ports of a Camtec JNT Pad. If unsure, say N.

config NET_FC
	bool "Fibre Channel driver support"
	depends on SCSI && PCI
	help
	  Fibre Channel is a high speed serial protocol mainly used to connect
	  large storage devices to the computer; it is compatible with and
	  intended to replace SCSI.

	  If you intend to use Fibre Channel, you need to have a Fibre channel
	  adaptor card in your computer; say Y here and to the driver for your
	  adaptor below. You also should have said Y to "SCSI support" and
	  "SCSI generic support".

config NETCONSOLE
	tristate "Network console logging support"
	---help---
	If you want to log kernel messages over the network, enable this.
	See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
	bool "Dynamic reconfiguration of logging targets"
	depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
			!(NETCONSOLE=y && CONFIGFS_FS=m)
	help
	  This option enables the ability to dynamically reconfigure target
	  parameters (interface, IP addresses, port numbers, MAC addresses)
	  at runtime through a userspace interface exported using configfs.
	  See <file:Documentation/networking/netconsole.txt> for details.

config NETPOLL
	def_bool NETCONSOLE

config NETPOLL_TRAP
	bool "Netpoll traffic trapping"
	default n
	depends on NETPOLL

config NET_POLL_CONTROLLER
	def_bool NETPOLL

config VIRTIO_NET
	tristate "Virtio network driver (EXPERIMENTAL)"
	depends on EXPERIMENTAL && VIRTIO
	---help---
	  This is the virtual network driver for virtio.  It can be used with
	  lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.

config VMXNET3
	tristate "VMware VMXNET3 ethernet driver"
	depends on PCI && INET
	help
	  This driver supports VMware's vmxnet3 virtual ethernet NIC.
	  To compile this driver as a module, choose M here: the
	  module will be called vmxnet3.

endif # NETDEVICES