| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117 |
- #
- # 1-wire slaves configuration
- #
- menu "1-wire Slaves"
- config W1_SLAVE_THERM
- tristate "Thermal family implementation"
- help
- Say Y here if you want to connect 1-wire thermal sensors to your
- wire.
- config W1_SLAVE_SMEM
- tristate "Simple 64bit memory family implementation"
- help
- Say Y here if you want to connect 1-wire
- simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.
- config W1_SLAVE_DS2408
- tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)"
- help
- Say Y here if you want to use a 1-wire
- DS2408 8-Channel Addressable Switch device support
- config W1_SLAVE_DS2423
- tristate "Counter 1-wire device (DS2423)"
- select CRC16
- help
- If you enable this you can read the counter values available
- in the DS2423 chipset from the w1_slave file under the
- sys file system.
- Say Y here if you want to use a 1-wire
- counter family device (DS2423).
- config W1_SLAVE_DS2431
- tristate "1kb EEPROM family support (DS2431)"
- help
- Say Y here if you want to use a 1-wire
- 1kb EEPROM family device (DS2431)
- config W1_SLAVE_DS2433
- tristate "4kb EEPROM family support (DS2433)"
- help
- Say Y here if you want to use a 1-wire
- 4kb EEPROM family device (DS2433).
- config W1_SLAVE_DS2433_CRC
- bool "Protect DS2433 data with a CRC16"
- depends on W1_SLAVE_DS2433
- select CRC16
- help
- Say Y here to protect DS2433 data with a CRC16.
- Each block has 30 bytes of data and a two byte CRC16.
- Full block writes are only allowed if the CRC is valid.
- config W1_SLAVE_DS2760
- tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)"
- depends on W1
- help
- If you enable this you will have the DS2760 battery monitor
- chip support.
- The battery monitor chip is used in many batteries/devices
- as the one who is responsible for charging/discharging/monitoring
- Li+ batteries.
- If you are unsure, say N.
- config W1_SLAVE_DS2780
- tristate "Dallas 2780 battery monitor chip"
- depends on W1
- help
- If you enable this you will have the DS2780 battery monitor
- chip support.
- The battery monitor chip is used in many batteries/devices
- as the one who is responsible for charging/discharging/monitoring
- Li+ batteries.
- If you are unsure, say N.
- config W1_SLAVE_DS2781
- tristate "Dallas 2781 battery monitor chip"
- depends on W1
- help
- If you enable this you will have the DS2781 battery monitor
- chip support.
- The battery monitor chip is used in many batteries/devices
- as the one who is responsible for charging/discharging/monitoring
- Li+ batteries.
- If you are unsure, say N.
- config W1_SLAVE_DS28E04
- tristate "4096-Bit Addressable 1-Wire EEPROM with PIO (DS28E04-100)"
- depends on W1
- select CRC16
- help
- If you enable this you will have the DS28E04-100
- chip support.
- Say Y here if you want to use a 1-wire
- 4kb EEPROM with PIO family device (DS28E04).
- If you are unsure, say N.
- config W1_SLAVE_BQ27000
- tristate "BQ27000 slave support"
- depends on W1
- help
- Say Y here if you want to use a hdq
- bq27000 slave support.
- endmenu
|
