Merge branch 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

From Kukjin Kim <kgene.kim@samsung.com>:

It is for supporting spi dt for exynos4210 and exynos5250, and got the
ack from Grant Likely for spi driver.

Note: Since this is including spi driver changes, so it was made based
on next/devel-dma-ops which touches same file, Samsung spi driver for
avoiding bad conflicts.

* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
  ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
  ARM: EXYNOS: Add spi clock support for EXYNOS5
  ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
  ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
  ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
  ARM: EXYNOS: Add device tree node for EXYNOS4 interrupt combiner controller
  spi: s3c64xx: add device tree support
  spi: s3c64xx: Remove the 'set_level' callback from controller data
  ARM: SAMSUNG: Modify s3c64xx_spi{0|1|2}_set_platdata function
  ARM: SAMSUNG: Remove pdev pointer parameter from spi gpio setup functions
  spi: s3c64xx: move controller information into driver data
  spi: s3c64xx: remove unused S3C64XX_SPI_ST_TRLCNTZ macro
  ARM: S3C64XX: Add a new dma request id for device tree based dma channel lookup

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/spi/spi-samsung.txt

@@ -0,0 +1,113 @@
+* Samsung SPI Controller
+
+The Samsung SPI controller is used to interface with various devices such as flash
+and display controllers using the SPI communication interface.
+
+Required SoC Specific Properties:
+
+- compatible: should be one of the following.
+    - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
+    - samsung,s3c6410-spi: for s3c6410 platforms
+    - samsung,s5p6440-spi: for s5p6440 and s5p6450 platforms
+    - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
+    - samsung,exynos4210-spi: for exynos4 and exynos5 platforms
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- interrupts: The interrupt number to the cpu. The interrupt specifier format
+  depends on the interrupt controller.
+
+- tx-dma-channel: The dma channel specifier for tx operations. The format of
+  the dma specifier depends on the dma controller.
+
+- rx-dma-channel: The dma channel specifier for rx operations. The format of
+  the dma specifier depends on the dma controller.
+
+Required Board Specific Properties:
+
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+- gpios: The gpio specifier for clock, mosi and miso interface lines (in the
+  order specified). The format of the gpio specifier depends on the gpio
+  controller.
+
+Optional Board Specific Properties:
+
+- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
+  select the clock source for the spi bus clock, this property can be used to
+  indicate the clock to be used for driving the spi bus clock. If not specified,
+  the clock number 0 is used as default.
+
+- num-cs: Specifies the number of chip select lines supported. If
+  not specified, the default number of chip select lines is set to 1.
+
+SPI Controller specific data in SPI slave nodes:
+
+- The spi slave nodes should provide the following information which is required
+  by the spi controller.
+
+  - cs-gpio: A gpio specifier that specifies the gpio line used as
+    the slave select line by the spi controller. The format of the gpio
+    specifier depends on the gpio controller.
+
+  - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
+    miso line (to account for any lag in the miso line). The following are the
+    valid values.
+
+      - 0: No phase shift.
+      - 1: 90 degree phase shift sampling.
+      - 2: 180 degree phase shift sampling.
+      - 3: 270 degree phase shift sampling.
+
+Aliases:
+
+- All the SPI controller nodes should be represented in the aliases node using
+  the following format 'spi{n}' where n is a unique number for the alias.
+
+
+Example:
+
+- SoC Specific Portion:
+
+	spi_0: spi@12d20000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d20000 0x100>;
+		interrupts = <0 66 0>;
+		tx-dma-channel = <&pdma0 5>;
+		rx-dma-channel = <&pdma0 4>;
+	};
+
+- Board Specific Portion:
+
+	spi_0: spi@12d20000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpa2 4 2 3 0>,
+			<&gpa2 6 2 3 0>,
+			<&gpa2 7 2 3 0>;
+
+		w25q80bw@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "w25x80";
+			reg = <0>;
+			spi-max-frequency = <10000>;
+
+			controller-data {
+				cs-gpio = <&gpa2 5 1 0 3>;
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "Kernel";
+				reg = <0x40000 0xc0000>;
+			};
+		};
+	};

arch/arm/boot/dts/exynos4210-origen.dts

@@ -134,4 +134,16 @@
 	i2c@138D0000 {
 		status = "disabled";
 	};
+
+	spi_0: spi@13920000 {
+		status = "disabled";
+	};
+
+	spi_1: spi@13930000 {
+		status = "disabled";
+	};
+
+	spi_2: spi@13940000 {
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/exynos4210-smdkv310.dts

@@ -179,4 +179,42 @@
 	i2c@138D0000 {
 		status = "disabled";
 	};
+
+	spi_0: spi@13920000 {
+		status = "disabled";
+	};
+
+	spi_1: spi@13930000 {
+		status = "disabled";
+	};
+
+	spi_2: spi@13940000 {
+		gpios = <&gpc1 1 5 3 0>,
+			<&gpc1 3 5 3 0>,
+			<&gpc1 4 5 3 0>;
+
+		w25x80@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "w25x80";
+			reg = <0>;
+			spi-max-frequency = <1000000>;
+
+			controller-data {
+				cs-gpio = <&gpc1 2 1 0 3>;
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "Kernel";
+				reg = <0x40000 0xc0000>;
+			};
+		};
+	};
 };

arch/arm/boot/dts/exynos4210.dtsi

@@ -25,6 +25,12 @@
 	compatible = "samsung,exynos4210";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		spi0 = &spi_0;
+		spi1 = &spi_1;
+		spi2 = &spi_2;
+	};
+
 	gic:interrupt-controller@10490000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
@@ -33,6 +39,17 @@
 		reg = <0x10490000 0x1000>, <0x10480000 0x100>;
 	};
 
+	combiner:interrupt-controller@10440000 {
+		compatible = "samsung,exynos4210-combiner";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <0x10440000 0x1000>;
+		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
+	};
+
 	watchdog@10060000 {
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x10060000 0x100>;
@@ -147,6 +164,36 @@
 		interrupts = <0 65 0>;
 	};
 
+	spi_0: spi@13920000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x13920000 0x100>;
+		interrupts = <0 66 0>;
+		tx-dma-channel = <&pdma0 7>;
+		rx-dma-channel = <&pdma0 6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_1: spi@13930000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x13930000 0x100>;
+		interrupts = <0 67 0>;
+		tx-dma-channel = <&pdma1 7>;
+		rx-dma-channel = <&pdma1 6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_2: spi@13940000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x13940000 0x100>;
+		interrupts = <0 68 0>;
+		tx-dma-channel = <&pdma0 9>;
+		rx-dma-channel = <&pdma0 8>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -71,4 +71,42 @@
 	i2c@12CD0000 {
 		status = "disabled";
 	};
+
+	spi_0: spi@12d20000 {
+		status = "disabled";
+	};
+
+	spi_1: spi@12d30000 {
+		gpios = <&gpa2 4 2 3 0>,
+			<&gpa2 6 2 3 0>,
+			<&gpa2 7 2 3 0>;
+
+		w25q80bw@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "w25x80";
+			reg = <0>;
+			spi-max-frequency = <1000000>;
+
+			controller-data {
+				cs-gpio = <&gpa2 5 1 0 3>;
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "Kernel";
+				reg = <0x40000 0xc0000>;
+			};
+		};
+	};
+
+	spi_2: spi@12d40000 {
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/exynos5250.dtsi

@@ -23,6 +23,12 @@
 	compatible = "samsung,exynos5250";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		spi0 = &spi_0;
+		spi1 = &spi_1;
+		spi2 = &spi_2;
+	};
+
 	gic:interrupt-controller@10481000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
@@ -146,6 +152,36 @@
 		#size-cells = <0>;
 	};
 
+	spi_0: spi@12d20000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d20000 0x100>;
+		interrupts = <0 66 0>;
+		tx-dma-channel = <&pdma0 5>;
+		rx-dma-channel = <&pdma0 4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_1: spi@12d30000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d30000 0x100>;
+		interrupts = <0 67 0>;
+		tx-dma-channel = <&pdma1 5>;
+		rx-dma-channel = <&pdma1 4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_2: spi@12d40000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d40000 0x100>;
+		interrupts = <0 68 0>;
+		tx-dma-channel = <&pdma0 7>;
+		rx-dma-channel = <&pdma0 6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/mach-exynos/clock-exynos4.c

@@ -586,17 +586,17 @@ static struct clk exynos4_init_clocks_off[] = {
 		.ctrlbit	= (1 << 13),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "exynos4210-spi.0",
 		.enable		= exynos4_clk_ip_peril_ctrl,
 		.ctrlbit	= (1 << 16),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "exynos4210-spi.1",
 		.enable		= exynos4_clk_ip_peril_ctrl,
 		.ctrlbit	= (1 << 17),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "exynos4210-spi.2",
 		.enable		= exynos4_clk_ip_peril_ctrl,
 		.ctrlbit	= (1 << 18),
 	}, {
@@ -1242,40 +1242,67 @@ static struct clksrc_clk exynos4_clk_sclk_mmc3 = {
 	.reg_div = { .reg = EXYNOS4_CLKDIV_FSYS2, .shift = 24, .size = 8 },
 };
 
+static struct clksrc_clk exynos4_clk_mdout_spi0 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.0",
+	},
+	.sources = &exynos4_clkset_group,
+	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 16, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk exynos4_clk_mdout_spi1 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.1",
+	},
+	.sources = &exynos4_clkset_group,
+	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 20, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk exynos4_clk_mdout_spi2 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.2",
+	},
+	.sources = &exynos4_clkset_group,
+	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 24, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL2, .shift = 0, .size = 4 },
+};
+
 static struct clksrc_clk exynos4_clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "exynos4210-spi.0",
+		.parent		= &exynos4_clk_mdout_spi0.clk,
 		.enable		= exynos4_clksrc_mask_peril1_ctrl,
 		.ctrlbit	= (1 << 16),
 	},
-	.sources = &exynos4_clkset_group,
-	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 16, .size = 4 },
-	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 0, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 8, .size = 8 },
 };
 
 static struct clksrc_clk exynos4_clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "exynos4210-spi.1",
+		.parent		= &exynos4_clk_mdout_spi1.clk,
 		.enable		= exynos4_clksrc_mask_peril1_ctrl,
 		.ctrlbit	= (1 << 20),
 	},
-	.sources = &exynos4_clkset_group,
-	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 20, .size = 4 },
-	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 16, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 24, .size = 8 },
 };
 
 static struct clksrc_clk exynos4_clk_sclk_spi2 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "exynos4210-spi.2",
+		.parent		= &exynos4_clk_mdout_spi2.clk,
 		.enable		= exynos4_clksrc_mask_peril1_ctrl,
 		.ctrlbit	= (1 << 24),
 	},
-	.sources = &exynos4_clkset_group,
-	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 24, .size = 4 },
-	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL2, .shift = 0, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL2, .shift = 8, .size = 8 },
 };
 
 /* Clock initialization code */
@@ -1331,7 +1358,9 @@ static struct clksrc_clk *exynos4_clksrc_cdev[] = {
 	&exynos4_clk_sclk_spi0,
 	&exynos4_clk_sclk_spi1,
 	&exynos4_clk_sclk_spi2,
-
+	&exynos4_clk_mdout_spi0,
+	&exynos4_clk_mdout_spi1,
+	&exynos4_clk_mdout_spi2,
 };
 
 static struct clk_lookup exynos4_clk_lookup[] = {
@@ -1347,9 +1376,9 @@ static struct clk_lookup exynos4_clk_lookup[] = {
 	CLKDEV_INIT("dma-pl330.0", "apb_pclk", &exynos4_clk_pdma0),
 	CLKDEV_INIT("dma-pl330.1", "apb_pclk", &exynos4_clk_pdma1),
 	CLKDEV_INIT("dma-pl330.2", "apb_pclk", &exynos4_clk_mdma1),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk0", &exynos4_clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk0", &exynos4_clk_sclk_spi1.clk),
-	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk0", &exynos4_clk_sclk_spi2.clk),
+	CLKDEV_INIT("exynos4210-spi.0", "spi_busclk0", &exynos4_clk_sclk_spi0.clk),
+	CLKDEV_INIT("exynos4210-spi.1", "spi_busclk0", &exynos4_clk_sclk_spi1.clk),
+	CLKDEV_INIT("exynos4210-spi.2", "spi_busclk0", &exynos4_clk_sclk_spi2.clk),
 };
 
 static int xtal_rate;

arch/arm/mach-exynos/clock-exynos5.c

@@ -131,6 +131,11 @@ static int exynos5_clksrc_mask_peric0_ctrl(struct clk *clk, int enable)
 	return s5p_gatectrl(EXYNOS5_CLKSRC_MASK_PERIC0, clk, enable);
 }
 
+static int exynos5_clksrc_mask_peric1_ctrl(struct clk *clk, int enable)
+{
+	return s5p_gatectrl(EXYNOS5_CLKSRC_MASK_PERIC1, clk, enable);
+}
+
 static int exynos5_clk_ip_acp_ctrl(struct clk *clk, int enable)
 {
 	return s5p_gatectrl(EXYNOS5_CLKGATE_IP_ACP, clk, enable);
@@ -740,6 +745,24 @@ static struct clk exynos5_init_clocks_off[] = {
 		.parent		= &exynos5_clk_aclk_66.clk,
 		.enable		= exynos5_clk_ip_peric_ctrl,
 		.ctrlbit	= (1 << 14),
+	}, {
+		.name		= "spi",
+		.devname	= "exynos4210-spi.0",
+		.parent		= &exynos5_clk_aclk_66.clk,
+		.enable		= exynos5_clk_ip_peric_ctrl,
+		.ctrlbit	= (1 << 16),
+	}, {
+		.name		= "spi",
+		.devname	= "exynos4210-spi.1",
+		.parent		= &exynos5_clk_aclk_66.clk,
+		.enable		= exynos5_clk_ip_peric_ctrl,
+		.ctrlbit	= (1 << 17),
+	}, {
+		.name		= "spi",
+		.devname	= "exynos4210-spi.2",
+		.parent		= &exynos5_clk_aclk_66.clk,
+		.enable		= exynos5_clk_ip_peric_ctrl,
+		.ctrlbit	= (1 << 18),
 	}, {
 		.name		= SYSMMU_CLOCK_NAME,
 		.devname	= SYSMMU_CLOCK_DEVNAME(mfc_l, 0),
@@ -1034,6 +1057,69 @@ static struct clksrc_clk exynos5_clk_sclk_mmc3 = {
 	.reg_div = { .reg = EXYNOS5_CLKDIV_FSYS2, .shift = 24, .size = 8 },
 };
 
+static struct clksrc_clk exynos5_clk_mdout_spi0 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.0",
+	},
+	.sources = &exynos5_clkset_group,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_PERIC1, .shift = 16, .size = 4 },
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk exynos5_clk_mdout_spi1 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.1",
+	},
+	.sources = &exynos5_clkset_group,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_PERIC1, .shift = 20, .size = 4 },
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk exynos5_clk_mdout_spi2 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.2",
+	},
+	.sources = &exynos5_clkset_group,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_PERIC1, .shift = 24, .size = 4 },
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk exynos5_clk_sclk_spi0 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "exynos4210-spi.0",
+		.parent		= &exynos5_clk_mdout_spi0.clk,
+		.enable		= exynos5_clksrc_mask_peric1_ctrl,
+		.ctrlbit	= (1 << 16),
+	},
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 8, .size = 8 },
+};
+
+static struct clksrc_clk exynos5_clk_sclk_spi1 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "exynos4210-spi.1",
+		.parent		= &exynos5_clk_mdout_spi1.clk,
+		.enable		= exynos5_clksrc_mask_peric1_ctrl,
+		.ctrlbit	= (1 << 20),
+	},
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 24, .size = 8 },
+};
+
+static struct clksrc_clk exynos5_clk_sclk_spi2 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "exynos4210-spi.2",
+		.parent		= &exynos5_clk_mdout_spi2.clk,
+		.enable		= exynos5_clksrc_mask_peric1_ctrl,
+		.ctrlbit	= (1 << 24),
+	},
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC2, .shift = 8, .size = 8 },
+};
+
 static struct clksrc_clk exynos5_clksrcs[] = {
 	{
 		.clk	= {
@@ -1148,6 +1234,12 @@ static struct clksrc_clk *exynos5_sysclks[] = {
 	&exynos5_clk_dout_mmc4,
 	&exynos5_clk_aclk_acp,
 	&exynos5_clk_pclk_acp,
+	&exynos5_clk_sclk_spi0,
+	&exynos5_clk_sclk_spi1,
+	&exynos5_clk_sclk_spi2,
+	&exynos5_clk_mdout_spi0,
+	&exynos5_clk_mdout_spi1,
+	&exynos5_clk_mdout_spi2,
 };
 
 static struct clk *exynos5_clk_cdev[] = {
@@ -1176,6 +1268,9 @@ static struct clk_lookup exynos5_clk_lookup[] = {
 	CLKDEV_INIT("exynos4-sdhci.1", "mmc_busclk.2", &exynos5_clk_sclk_mmc1.clk),
 	CLKDEV_INIT("exynos4-sdhci.2", "mmc_busclk.2", &exynos5_clk_sclk_mmc2.clk),
 	CLKDEV_INIT("exynos4-sdhci.3", "mmc_busclk.2", &exynos5_clk_sclk_mmc3.clk),
+	CLKDEV_INIT("exynos4210-spi.0", "spi_busclk0", &exynos5_clk_sclk_spi0.clk),
+	CLKDEV_INIT("exynos4210-spi.1", "spi_busclk0", &exynos5_clk_sclk_spi1.clk),
+	CLKDEV_INIT("exynos4210-spi.2", "spi_busclk0", &exynos5_clk_sclk_spi2.clk),
 	CLKDEV_INIT("dma-pl330.0", "apb_pclk", &exynos5_clk_pdma0),
 	CLKDEV_INIT("dma-pl330.1", "apb_pclk", &exynos5_clk_pdma1),
 	CLKDEV_INIT("dma-pl330.2", "apb_pclk", &exynos5_clk_mdma1),

arch/arm/mach-exynos/include/mach/irqs.h

@@ -195,6 +195,10 @@
 #define IRQ_IIC6			EXYNOS4_IRQ_IIC6
 #define IRQ_IIC7			EXYNOS4_IRQ_IIC7
 
+#define IRQ_SPI0			EXYNOS4_IRQ_SPI0
+#define IRQ_SPI1			EXYNOS4_IRQ_SPI1
+#define IRQ_SPI2			EXYNOS4_IRQ_SPI2
+
 #define IRQ_USB_HOST			EXYNOS4_IRQ_USB_HOST
 #define IRQ_OTG				EXYNOS4_IRQ_USB_HSOTG
 

arch/arm/mach-exynos/include/mach/map.h

@@ -154,6 +154,9 @@
 #define EXYNOS4_PA_SPI0			0x13920000
 #define EXYNOS4_PA_SPI1			0x13930000
 #define EXYNOS4_PA_SPI2			0x13940000
+#define EXYNOS5_PA_SPI0			0x12D20000
+#define EXYNOS5_PA_SPI1			0x12D30000
+#define EXYNOS5_PA_SPI2			0x12D40000
 
 #define EXYNOS4_PA_GPIO1		0x11400000
 #define EXYNOS4_PA_GPIO2		0x11000000

arch/arm/mach-exynos/mach-exynos4-dt.c

@@ -55,6 +55,12 @@ static const struct of_dev_auxdata exynos4210_auxdata_lookup[] __initconst = {
 				"exynos4-sdhci.3", NULL),
 	OF_DEV_AUXDATA("samsung,s3c2440-i2c", EXYNOS4_PA_IIC(0),
 				"s3c2440-i2c.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS4_PA_SPI0,
+				"exynos4210-spi.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS4_PA_SPI1,
+				"exynos4210-spi.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS4_PA_SPI2,
+				"exynos4210-spi.2", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA0, "dma-pl330.0", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA1, "dma-pl330.1", NULL),
 	{},

arch/arm/mach-exynos/mach-exynos5-dt.c

@@ -47,6 +47,12 @@ static const struct of_dev_auxdata exynos5250_auxdata_lookup[] __initconst = {
 				"s3c2440-i2c.0", NULL),
 	OF_DEV_AUXDATA("samsung,s3c2440-i2c", EXYNOS5_PA_IIC(1),
 				"s3c2440-i2c.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS5_PA_SPI0,
+				"exynos4210-spi.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS5_PA_SPI1,
+				"exynos4210-spi.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS5_PA_SPI2,
+				"exynos4210-spi.2", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA0, "dma-pl330.0", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA1, "dma-pl330.1", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_MDMA1, "dma-pl330.2", NULL),

arch/arm/mach-exynos/setup-spi.c

@@ -9,21 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.clk_from_cmu	= true,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(EXYNOS4_GPB(0), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(EXYNOS4_GPB(0), S3C_GPIO_PULL_UP);
@@ -34,15 +23,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.clk_from_cmu	= true,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(EXYNOS4_GPB(4), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(EXYNOS4_GPB(4), S3C_GPIO_PULL_UP);
@@ -53,15 +34,7 @@ int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI2
-struct s3c64xx_spi_info s3c64xx_spi2_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.clk_from_cmu	= true,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi2_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi2_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(EXYNOS4_GPC1(1), S3C_GPIO_SFN(5));
 	s3c_gpio_setpull(EXYNOS4_GPC1(1), S3C_GPIO_PULL_UP);

arch/arm/mach-s3c24xx/clock-s3c2416.c

@@ -144,7 +144,8 @@ static struct clk_lookup s3c2416_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &hsmmc0_clk),
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &hsmmc_mux0.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &hsmmc_mux1.clk),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &hsspi_mux.clk),
+	/* s3c2443-spi.0 is used on s3c2416 and s3c2450 as well */
+	CLKDEV_INIT("s3c2443-spi.0", "spi_busclk2", &hsspi_mux.clk),
 };
 
 void __init s3c2416_init_clocks(int xtal)

arch/arm/mach-s3c24xx/clock-s3c2443.c

@@ -181,7 +181,7 @@ static struct clk *clks[] __initdata = {
 
 static struct clk_lookup s3c2443_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_hsmmc),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_hsspi.clk),
+	CLKDEV_INIT("s3c2443-spi.0", "spi_busclk2", &clk_hsspi.clk),
 };
 
 void __init s3c2443_init_clocks(int xtal)

arch/arm/mach-s3c24xx/common-s3c2443.c

@@ -559,7 +559,7 @@ static struct clk hsmmc1_clk = {
 
 static struct clk hsspi_clk = {
 	.name		= "spi",
-	.devname	= "s3c64xx-spi.0",
+	.devname	= "s3c2443-spi.0",
 	.parent		= &clk_p,
 	.enable		= s3c2443_clkcon_enable_p,
 	.ctrlbit	= S3C2443_PCLKCON_HSSPI,
@@ -633,7 +633,7 @@ static struct clk_lookup s3c2443_clk_lookup[] = {
 	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
 	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_esys_uart.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &hsmmc1_clk),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk0", &hsspi_clk),
+	CLKDEV_INIT("s3c2443-spi.0", "spi_busclk0", &hsspi_clk),
 };
 
 void __init s3c2443_common_init_clocks(int xtal, pll_fn get_mpll,

arch/arm/mach-s3c24xx/setup-spi.c

@@ -13,20 +13,12 @@
 #include <linux/platform_device.h>
 
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #include <mach/hardware.h>
 #include <mach/regs-gpio.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.tx_st_done	= 21,
-	.high_speed	= 1,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *pdev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	/* enable hsspi bit in misccr */
 	s3c2410_modify_misccr(S3C2416_MISCCR_HSSPI_EN2, 1);

arch/arm/mach-s3c64xx/clock.c

@@ -178,13 +178,13 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= S3C_CLKCON_PCLK_KEYPAD,
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s3c6410-spi.0",
 		.parent		= &clk_p,
 		.enable		= s3c64xx_pclk_ctrl,
 		.ctrlbit	= S3C_CLKCON_PCLK_SPI0,
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s3c6410-spi.1",
 		.parent		= &clk_p,
 		.enable		= s3c64xx_pclk_ctrl,
 		.ctrlbit	= S3C_CLKCON_PCLK_SPI1,
@@ -331,7 +331,7 @@ static struct clk init_clocks_off[] = {
 
 static struct clk clk_48m_spi0 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.0",
+	.devname	= "s3c6410-spi.0",
 	.parent		= &clk_48m,
 	.enable		= s3c64xx_sclk_ctrl,
 	.ctrlbit	= S3C_CLKCON_SCLK_SPI0_48,
@@ -339,7 +339,7 @@ static struct clk clk_48m_spi0 = {
 
 static struct clk clk_48m_spi1 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.1",
+	.devname	= "s3c6410-spi.1",
 	.parent		= &clk_48m,
 	.enable		= s3c64xx_sclk_ctrl,
 	.ctrlbit	= S3C_CLKCON_SCLK_SPI1_48,
@@ -802,7 +802,7 @@ static struct clksrc_clk clk_sclk_mmc2 = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "spi-bus",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s3c6410-spi.0",
 		.ctrlbit	= S3C_CLKCON_SCLK_SPI0,
 		.enable		= s3c64xx_sclk_ctrl,
 	},
@@ -814,7 +814,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "spi-bus",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s3c6410-spi.1",
 		.ctrlbit	= S3C_CLKCON_SCLK_SPI1,
 		.enable		= s3c64xx_sclk_ctrl,
 	},
@@ -858,10 +858,10 @@ static struct clk_lookup s3c64xx_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_48m_spi0),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_48m_spi1),
+	CLKDEV_INIT("s3c6410-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s3c6410-spi.0", "spi_busclk2", &clk_48m_spi0),
+	CLKDEV_INIT("s3c6410-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s3c6410-spi.1", "spi_busclk2", &clk_48m_spi1),
 };
 
 #define GET_DIV(clk, field) ((((clk) & field##_MASK) >> field##_SHIFT) + 1)

arch/arm/mach-s3c64xx/include/mach/dma.h

@@ -21,6 +21,7 @@
  */
 enum dma_ch {
 	/* DMA0/SDMA0 */
+	DMACH_DT_PROP = -1, /* not yet supported, do not use */
 	DMACH_UART0 = 0,
 	DMACH_UART0_SRC2,
 	DMACH_UART1,

arch/arm/mach-s3c64xx/mach-crag6410.c

@@ -799,7 +799,7 @@ static void __init crag6410_machine_init(void)
 	i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
 
 	samsung_keypad_set_platdata(&crag6410_keypad_data);
-	s3c64xx_spi0_set_platdata(&s3c64xx_spi0_pdata, 0, 1);
+	s3c64xx_spi0_set_platdata(NULL, 0, 1);
 
 	platform_add_devices(crag6410_devices, ARRAY_SIZE(crag6410_devices));
 

arch/arm/mach-s3c64xx/setup-spi.c

@@ -9,19 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S3C64XX_GPC(0), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
@@ -30,13 +21,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S3C64XX_GPC(4), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);

arch/arm/mach-s5p64x0/clock-s5p6440.c

@@ -227,13 +227,13 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 17),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 21),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 22),
@@ -467,7 +467,7 @@ static struct clksrc_clk clk_sclk_uclk = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.ctrlbit	= (1 << 20),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -479,7 +479,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.ctrlbit	= (1 << 21),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -519,8 +519,8 @@ static struct clk_lookup s5p6440_clk_lookup[] = {
 	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
 	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5p64x0-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5p64x0-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),

arch/arm/mach-s5p64x0/clock-s5p6450.c

@@ -236,13 +236,13 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 17),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 21),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 22),
@@ -528,7 +528,7 @@ static struct clksrc_clk clk_sclk_uclk = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.ctrlbit	= (1 << 20),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -540,7 +540,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.ctrlbit	= (1 << 21),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -562,8 +562,8 @@ static struct clk_lookup s5p6450_clk_lookup[] = {
 	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
 	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5p64x0-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5p64x0-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),

arch/arm/mach-s5p64x0/setup-spi.c

@@ -9,21 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/cpu.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	if (soc_is_s5p6450())
 		s3c_gpio_cfgall_range(S5P6450_GPC(0), 3,
@@ -36,13 +25,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	if (soc_is_s5p6450())
 		s3c_gpio_cfgall_range(S5P6450_GPC(4), 3,

arch/arm/mach-s5pc100/clock.c

@@ -564,19 +564,19 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 5),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pc100-spi.0",
 		.parent		= &clk_div_d1_bus.clk,
 		.enable		= s5pc100_d1_4_ctrl,
 		.ctrlbit	= (1 << 6),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pc100-spi.1",
 		.parent		= &clk_div_d1_bus.clk,
 		.enable		= s5pc100_d1_4_ctrl,
 		.ctrlbit	= (1 << 7),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "s5pc100-spi.2",
 		.parent		= &clk_div_d1_bus.clk,
 		.enable		= s5pc100_d1_4_ctrl,
 		.ctrlbit	= (1 << 8),
@@ -702,7 +702,7 @@ static struct clk clk_hsmmc0 = {
 
 static struct clk clk_48m_spi0 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.0",
+	.devname	= "s5pc100-spi.0",
 	.parent		= &clk_mout_48m.clk,
 	.enable		= s5pc100_sclk0_ctrl,
 	.ctrlbit	= (1 << 7),
@@ -710,7 +710,7 @@ static struct clk clk_48m_spi0 = {
 
 static struct clk clk_48m_spi1 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.1",
+	.devname	= "s5pc100-spi.1",
 	.parent		= &clk_mout_48m.clk,
 	.enable		= s5pc100_sclk0_ctrl,
 	.ctrlbit	= (1 << 8),
@@ -718,7 +718,7 @@ static struct clk clk_48m_spi1 = {
 
 static struct clk clk_48m_spi2 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.2",
+	.devname	= "s5pc100-spi.2",
 	.parent		= &clk_mout_48m.clk,
 	.enable		= s5pc100_sclk0_ctrl,
 	.ctrlbit	= (1 << 9),
@@ -1085,7 +1085,7 @@ static struct clksrc_clk clk_sclk_mmc2 = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pc100-spi.0",
 		.ctrlbit	= (1 << 4),
 		.enable		= s5pc100_sclk0_ctrl,
 	},
@@ -1097,7 +1097,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pc100-spi.1",
 		.ctrlbit	= (1 << 5),
 		.enable		= s5pc100_sclk0_ctrl,
 	},
@@ -1109,7 +1109,7 @@ static struct clksrc_clk clk_sclk_spi1 = {
 static struct clksrc_clk clk_sclk_spi2 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "s5pc100-spi.2",
 		.ctrlbit	= (1 << 6),
 		.enable		= s5pc100_sclk0_ctrl,
 	},
@@ -1315,12 +1315,12 @@ static struct clk_lookup s5pc100_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_48m_spi0),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_48m_spi1),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_sclk_spi1.clk),
-	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk1", &clk_48m_spi2),
-	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk2", &clk_sclk_spi2.clk),
+	CLKDEV_INIT("s5pc100-spi.0", "spi_busclk1", &clk_48m_spi0),
+	CLKDEV_INIT("s5pc100-spi.0", "spi_busclk2", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5pc100-spi.1", "spi_busclk1", &clk_48m_spi1),
+	CLKDEV_INIT("s5pc100-spi.1", "spi_busclk2", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5pc100-spi.2", "spi_busclk1", &clk_48m_spi2),
+	CLKDEV_INIT("s5pc100-spi.2", "spi_busclk2", &clk_sclk_spi2.clk),
 };
 
 void __init s5pc100_register_clocks(void)

arch/arm/mach-s5pc100/setup-spi.c

@@ -9,20 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.high_speed	= 1,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S5PC100_GPB(0), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
@@ -31,14 +21,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.high_speed	= 1,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S5PC100_GPB(4), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
@@ -47,14 +30,7 @@ int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI2
-struct s3c64xx_spi_info s3c64xx_spi2_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.high_speed	= 1,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi2_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi2_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(S5PC100_GPG3(0), S3C_GPIO_SFN(3));
 	s3c_gpio_setpull(S5PC100_GPG3(0), S3C_GPIO_PULL_UP);

arch/arm/mach-s5pv210/clock.c

@@ -445,19 +445,19 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 11),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pv210-spi.0",
 		.parent		= &clk_pclk_psys.clk,
 		.enable		= s5pv210_clk_ip3_ctrl,
 		.ctrlbit	= (1<<12),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pv210-spi.1",
 		.parent		= &clk_pclk_psys.clk,
 		.enable		= s5pv210_clk_ip3_ctrl,
 		.ctrlbit	= (1<<13),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "s5pv210-spi.2",
 		.parent		= &clk_pclk_psys.clk,
 		.enable		= s5pv210_clk_ip3_ctrl,
 		.ctrlbit	= (1<<14),
@@ -1035,7 +1035,7 @@ static struct clksrc_clk clk_sclk_mmc3 = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk		= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pv210-spi.0",
 		.enable		= s5pv210_clk_mask0_ctrl,
 		.ctrlbit	= (1 << 16),
 	},
@@ -1047,7 +1047,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk		= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pv210-spi.1",
 		.enable		= s5pv210_clk_mask0_ctrl,
 		.ctrlbit	= (1 << 17),
 	},
@@ -1331,8 +1331,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
 	CLKDEV_INIT("s3c-sdhci.3", "mmc_busclk.2", &clk_sclk_mmc3.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
 };
 
 void __init s5pv210_register_clocks(void)

arch/arm/mach-s5pv210/setup-spi.c

@@ -9,20 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata = {
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(S5PV210_GPB(0), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(S5PV210_GPB(0), S3C_GPIO_PULL_UP);
@@ -33,14 +23,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(S5PV210_GPB(4), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(S5PV210_GPB(4), S3C_GPIO_PULL_UP);

arch/arm/plat-samsung/devs.c

@@ -1512,7 +1512,7 @@ static struct resource s3c64xx_spi0_resource[] = {
 };
 
 struct platform_device s3c64xx_device_spi0 = {
-	.name		= "s3c64xx-spi",
+	.name		= "s3c6410-spi",
 	.id		= 0,
 	.num_resources	= ARRAY_SIZE(s3c64xx_spi0_resource),
 	.resource	= s3c64xx_spi0_resource,
@@ -1522,13 +1522,10 @@ struct platform_device s3c64xx_device_spi0 = {
 	},
 };
 
-void __init s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs)
+void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
 {
-	if (!pd) {
-		pr_err("%s:Need to pass platform data\n", __func__);
-		return;
-	}
+	struct s3c64xx_spi_info pd;
 
 	/* Reject invalid configuration */
 	if (!num_cs || src_clk_nr < 0) {
@@ -1536,12 +1533,11 @@ void __init s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
 		return;
 	}
 
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	if (!pd->cfg_gpio)
-		pd->cfg_gpio = s3c64xx_spi0_cfg_gpio;
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi0_cfg_gpio;
 
-	s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi0);
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi0);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI0 */
 
@@ -1554,7 +1550,7 @@ static struct resource s3c64xx_spi1_resource[] = {
 };
 
 struct platform_device s3c64xx_device_spi1 = {
-	.name		= "s3c64xx-spi",
+	.name		= "s3c6410-spi",
 	.id		= 1,
 	.num_resources	= ARRAY_SIZE(s3c64xx_spi1_resource),
 	.resource	= s3c64xx_spi1_resource,
@@ -1564,26 +1560,20 @@ struct platform_device s3c64xx_device_spi1 = {
 	},
 };
 
-void __init s3c64xx_spi1_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs)
+void __init s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
 {
-	if (!pd) {
-		pr_err("%s:Need to pass platform data\n", __func__);
-		return;
-	}
-
 	/* Reject invalid configuration */
 	if (!num_cs || src_clk_nr < 0) {
 		pr_err("%s: Invalid SPI configuration\n", __func__);
 		return;
 	}
 
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	if (!pd->cfg_gpio)
-		pd->cfg_gpio = s3c64xx_spi1_cfg_gpio;
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi1_cfg_gpio;
 
-	s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi1);
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi1);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI1 */
 
@@ -1596,7 +1586,7 @@ static struct resource s3c64xx_spi2_resource[] = {
 };
 
 struct platform_device s3c64xx_device_spi2 = {
-	.name		= "s3c64xx-spi",
+	.name		= "s3c6410-spi",
 	.id		= 2,
 	.num_resources	= ARRAY_SIZE(s3c64xx_spi2_resource),
 	.resource	= s3c64xx_spi2_resource,
@@ -1606,13 +1596,10 @@ struct platform_device s3c64xx_device_spi2 = {
 	},
 };
 
-void __init s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs)
+void __init s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
 {
-	if (!pd) {
-		pr_err("%s:Need to pass platform data\n", __func__);
-		return;
-	}
+	struct s3c64xx_spi_info pd;
 
 	/* Reject invalid configuration */
 	if (!num_cs || src_clk_nr < 0) {
@@ -1620,11 +1607,10 @@ void __init s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
 		return;
 	}
 
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	if (!pd->cfg_gpio)
-		pd->cfg_gpio = s3c64xx_spi2_cfg_gpio;
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi2_cfg_gpio;
 
-	s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi2);
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi2);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI2 */

arch/arm/plat-samsung/include/plat/s3c64xx-spi.h

@@ -18,7 +18,6 @@ struct platform_device;
  * @fb_delay: Slave specific feedback delay.
  *            Refer to FB_CLK_SEL register definition in SPI chapter.
  * @line: Custom 'identity' of the CS line.
- * @set_level: CS line control.
  *
  * This is per SPI-Slave Chipselect information.
  * Allocate and initialize one in machine init code and make the
@@ -27,57 +26,41 @@ struct platform_device;
 struct s3c64xx_spi_csinfo {
 	u8 fb_delay;
 	unsigned line;
-	void (*set_level)(unsigned line_id, int lvl);
 };
 
 /**
  * struct s3c64xx_spi_info - SPI Controller defining structure
  * @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
- * @clk_from_cmu: If the SPI clock/prescalar control block is present
- *     by the platform's clock-management-unit and not in SPI controller.
  * @num_cs: Number of CS this controller emulates.
  * @cfg_gpio: Configure pins for this SPI controller.
- * @fifo_lvl_mask: All tx fifo_lvl fields start at offset-6
- * @rx_lvl_offset: Depends on tx fifo_lvl field and bus number
- * @high_speed: If the controller supports HIGH_SPEED_EN bit
- * @tx_st_done: Depends on tx fifo_lvl field
  */
 struct s3c64xx_spi_info {
 	int src_clk_nr;
-	bool clk_from_cmu;
-
 	int num_cs;
-
-	int (*cfg_gpio)(struct platform_device *pdev);
-
-	/* Following two fields are for future compatibility */
-	int fifo_lvl_mask;
-	int rx_lvl_offset;
-	int high_speed;
-	int tx_st_done;
+	int (*cfg_gpio)(void);
 };
 
 /**
  * s3c64xx_spi_set_platdata - SPI Controller configure callback by the board
  *				initialization code.
- * @pd: SPI platform data to set.
+ * @cfg_gpio: Pointer to gpio setup function.
  * @src_clk_nr: Clock the SPI controller is to use to generate SPI clocks.
  * @num_cs: Number of elements in the 'cs' array.
  *
  * Call this from machine init code for each SPI Controller that
  * has some chips attached to it.
  */
-extern void s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs);
-extern void s3c64xx_spi1_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs);
-extern void s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs);
+extern void s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs);
+extern void s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs);
+extern void s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs);
 
 /* defined by architecture to configure gpio */
-extern int s3c64xx_spi0_cfg_gpio(struct platform_device *dev);
-extern int s3c64xx_spi1_cfg_gpio(struct platform_device *dev);
-extern int s3c64xx_spi2_cfg_gpio(struct platform_device *dev);
+extern int s3c64xx_spi0_cfg_gpio(void);
+extern int s3c64xx_spi1_cfg_gpio(void);
+extern int s3c64xx_spi2_cfg_gpio(void);
 
 extern struct s3c64xx_spi_info s3c64xx_spi0_pdata;
 extern struct s3c64xx_spi_info s3c64xx_spi1_pdata;

drivers/spi/spi-s3c64xx.c

@@ -27,10 +27,15 @@
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/spi/spi.h>
+#include <linux/gpio.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
 
 #include <mach/dma.h>
 #include <plat/s3c64xx-spi.h>
 
+#define MAX_SPI_PORTS		3
+
 /* Registers and bit-fields */
 
 #define S3C64XX_SPI_CH_CFG		0x00
@@ -113,13 +118,12 @@
 
 #define S3C64XX_SPI_FBCLK_MSK		(3<<0)
 
-#define S3C64XX_SPI_ST_TRLCNTZ(v, i) ((((v) >> (i)->rx_lvl_offset) & \
-					(((i)->fifo_lvl_mask + 1))) \
-					? 1 : 0)
-
-#define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & (1 << (i)->tx_st_done)) ? 1 : 0)
-#define TX_FIFO_LVL(v, i) (((v) >> 6) & (i)->fifo_lvl_mask)
-#define RX_FIFO_LVL(v, i) (((v) >> (i)->rx_lvl_offset) & (i)->fifo_lvl_mask)
+#define FIFO_LVL_MASK(i) ((i)->port_conf->fifo_lvl_mask[i->port_id])
+#define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & \
+				(1 << (i)->port_conf->tx_st_done)) ? 1 : 0)
+#define TX_FIFO_LVL(v, i) (((v) >> 6) & FIFO_LVL_MASK(i))
+#define RX_FIFO_LVL(v, i) (((v) >> (i)->port_conf->rx_lvl_offset) & \
+					FIFO_LVL_MASK(i))
 
 #define S3C64XX_SPI_MAX_TRAILCNT	0x3ff
 #define S3C64XX_SPI_TRAILCNT_OFF	19
@@ -135,6 +139,29 @@ struct s3c64xx_spi_dma_data {
 	unsigned		ch;
 	enum dma_data_direction direction;
 	enum dma_ch	dmach;
+	struct property		*dma_prop;
+};
+
+/**
+ * struct s3c64xx_spi_info - SPI Controller hardware info
+ * @fifo_lvl_mask: Bit-mask for {TX|RX}_FIFO_LVL bits in SPI_STATUS register.
+ * @rx_lvl_offset: Bit offset of RX_FIFO_LVL bits in SPI_STATUS regiter.
+ * @tx_st_done: Bit offset of TX_DONE bit in SPI_STATUS regiter.
+ * @high_speed: True, if the controller supports HIGH_SPEED_EN bit.
+ * @clk_from_cmu: True, if the controller does not include a clock mux and
+ *	prescaler unit.
+ *
+ * The Samsung s3c64xx SPI controller are used on various Samsung SoC's but
+ * differ in some aspects such as the size of the fifo and spi bus clock
+ * setup. Such differences are specified to the driver using this structure
+ * which is provided as driver data to the driver.
+ */
+struct s3c64xx_spi_port_config {
+	int	fifo_lvl_mask[MAX_SPI_PORTS];
+	int	rx_lvl_offset;
+	int	tx_st_done;
+	bool	high_speed;
+	bool	clk_from_cmu;
 };
 
 /**
@@ -175,6 +202,9 @@ struct s3c64xx_spi_driver_data {
 	struct s3c64xx_spi_dma_data	rx_dma;
 	struct s3c64xx_spi_dma_data	tx_dma;
 	struct samsung_dma_ops		*ops;
+	struct s3c64xx_spi_port_config	*port_conf;
+	unsigned int			port_id;
+	unsigned long			gpios[4];
 };
 
 static struct s3c2410_dma_client s3c64xx_spi_dma_client = {
@@ -183,7 +213,6 @@ static struct s3c2410_dma_client s3c64xx_spi_dma_client = {
 
 static void flush_fifo(struct s3c64xx_spi_driver_data *sdd)
 {
-	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 	void __iomem *regs = sdd->regs;
 	unsigned long loops;
 	u32 val;
@@ -199,7 +228,7 @@ static void flush_fifo(struct s3c64xx_spi_driver_data *sdd)
 	loops = msecs_to_loops(1);
 	do {
 		val = readl(regs + S3C64XX_SPI_STATUS);
-	} while (TX_FIFO_LVL(val, sci) && loops--);
+	} while (TX_FIFO_LVL(val, sdd) && loops--);
 
 	if (loops == 0)
 		dev_warn(&sdd->pdev->dev, "Timed out flushing TX FIFO\n");
@@ -208,7 +237,7 @@ static void flush_fifo(struct s3c64xx_spi_driver_data *sdd)
 	loops = msecs_to_loops(1);
 	do {
 		val = readl(regs + S3C64XX_SPI_STATUS);
-		if (RX_FIFO_LVL(val, sci))
+		if (RX_FIFO_LVL(val, sdd))
 			readl(regs + S3C64XX_SPI_RX_DATA);
 		else
 			break;
@@ -301,7 +330,9 @@ static int acquire_dma(struct s3c64xx_spi_driver_data *sdd)
 	req.cap = DMA_SLAVE;
 	req.client = &s3c64xx_spi_dma_client;
 
+	req.dt_dmach_prop = sdd->rx_dma.dma_prop;
 	sdd->rx_dma.ch = sdd->ops->request(sdd->rx_dma.dmach, &req);
+	req.dt_dmach_prop = sdd->tx_dma.dma_prop;
 	sdd->tx_dma.ch = sdd->ops->request(sdd->tx_dma.dmach, &req);
 
 	return 1;
@@ -311,7 +342,6 @@ static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
 				struct spi_device *spi,
 				struct spi_transfer *xfer, int dma_mode)
 {
-	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 	void __iomem *regs = sdd->regs;
 	u32 modecfg, chcfg;
 
@@ -361,7 +391,7 @@ static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
 	if (xfer->rx_buf != NULL) {
 		sdd->state |= RXBUSY;
 
-		if (sci->high_speed && sdd->cur_speed >= 30000000UL
+		if (sdd->port_conf->high_speed && sdd->cur_speed >= 30000000UL
 					&& !(sdd->cur_mode & SPI_CPHA))
 			chcfg |= S3C64XX_SPI_CH_HS_EN;
 
@@ -388,20 +418,19 @@ static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd,
 		if (sdd->tgl_spi != spi) { /* if last mssg on diff device */
 			/* Deselect the last toggled device */
 			cs = sdd->tgl_spi->controller_data;
-			cs->set_level(cs->line,
-					spi->mode & SPI_CS_HIGH ? 0 : 1);
+			gpio_set_value(cs->line,
+				spi->mode & SPI_CS_HIGH ? 0 : 1);
 		}
 		sdd->tgl_spi = NULL;
 	}
 
 	cs = spi->controller_data;
-	cs->set_level(cs->line, spi->mode & SPI_CS_HIGH ? 1 : 0);
+	gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 1 : 0);
 }
 
 static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
 				struct spi_transfer *xfer, int dma_mode)
 {
-	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 	void __iomem *regs = sdd->regs;
 	unsigned long val;
 	int ms;
@@ -418,7 +447,7 @@ static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
 		val = msecs_to_loops(ms);
 		do {
 			status = readl(regs + S3C64XX_SPI_STATUS);
-		} while (RX_FIFO_LVL(status, sci) < xfer->len && --val);
+		} while (RX_FIFO_LVL(status, sdd) < xfer->len && --val);
 	}
 
 	if (!val)
@@ -437,8 +466,8 @@ static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
 		if (xfer->rx_buf == NULL) {
 			val = msecs_to_loops(10);
 			status = readl(regs + S3C64XX_SPI_STATUS);
-			while ((TX_FIFO_LVL(status, sci)
-				|| !S3C64XX_SPI_ST_TX_DONE(status, sci))
+			while ((TX_FIFO_LVL(status, sdd)
+				|| !S3C64XX_SPI_ST_TX_DONE(status, sdd))
 					&& --val) {
 				cpu_relax();
 				status = readl(regs + S3C64XX_SPI_STATUS);
@@ -482,17 +511,16 @@ static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd,
 	if (sdd->tgl_spi == spi)
 		sdd->tgl_spi = NULL;
 
-	cs->set_level(cs->line, spi->mode & SPI_CS_HIGH ? 0 : 1);
+	gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 0 : 1);
 }
 
 static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
 {
-	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 	void __iomem *regs = sdd->regs;
 	u32 val;
 
 	/* Disable Clock */
-	if (sci->clk_from_cmu) {
+	if (sdd->port_conf->clk_from_cmu) {
 		clk_disable(sdd->src_clk);
 	} else {
 		val = readl(regs + S3C64XX_SPI_CLK_CFG);
@@ -536,7 +564,7 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
 
 	writel(val, regs + S3C64XX_SPI_MODE_CFG);
 
-	if (sci->clk_from_cmu) {
+	if (sdd->port_conf->clk_from_cmu) {
 		/* Configure Clock */
 		/* There is half-multiplier before the SPI */
 		clk_set_rate(sdd->src_clk, sdd->cur_speed * 2);
@@ -562,7 +590,6 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
 static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
 						struct spi_message *msg)
 {
-	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 	struct device *dev = &sdd->pdev->dev;
 	struct spi_transfer *xfer;
 
@@ -578,7 +605,7 @@ static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
 	/* Map until end or first fail */
 	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 
-		if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1))
+		if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1))
 			continue;
 
 		if (xfer->tx_buf != NULL) {
@@ -612,7 +639,6 @@ static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
 static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd,
 						struct spi_message *msg)
 {
-	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 	struct device *dev = &sdd->pdev->dev;
 	struct spi_transfer *xfer;
 
@@ -621,7 +647,7 @@ static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd,
 
 	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 
-		if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1))
+		if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1))
 			continue;
 
 		if (xfer->rx_buf != NULL
@@ -640,7 +666,6 @@ static int s3c64xx_spi_transfer_one_message(struct spi_master *master,
 					    struct spi_message *msg)
 {
 	struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
-	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 	struct spi_device *spi = msg->spi;
 	struct s3c64xx_spi_csinfo *cs = spi->controller_data;
 	struct spi_transfer *xfer;
@@ -695,7 +720,7 @@ static int s3c64xx_spi_transfer_one_message(struct spi_master *master,
 		}
 
 		/* Polling method for xfers not bigger than FIFO capacity */
-		if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1))
+		if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1))
 			use_dma = 0;
 		else
 			use_dma = 1;
@@ -800,6 +825,48 @@ static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi)
 	return 0;
 }
 
+static struct s3c64xx_spi_csinfo *s3c64xx_get_slave_ctrldata(
+				struct s3c64xx_spi_driver_data *sdd,
+				struct spi_device *spi)
+{
+	struct s3c64xx_spi_csinfo *cs;
+	struct device_node *slave_np, *data_np;
+	u32 fb_delay = 0;
+
+	slave_np = spi->dev.of_node;
+	if (!slave_np) {
+		dev_err(&spi->dev, "device node not found\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	for_each_child_of_node(slave_np, data_np)
+		if (!strcmp(data_np->name, "controller-data"))
+			break;
+	if (!data_np) {
+		dev_err(&spi->dev, "child node 'controller-data' not found\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	cs = kzalloc(sizeof(*cs), GFP_KERNEL);
+	if (!cs) {
+		dev_err(&spi->dev, "could not allocate memory for controller"
+					" data\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	cs->line = of_get_named_gpio(data_np, "cs-gpio", 0);
+	if (!gpio_is_valid(cs->line)) {
+		dev_err(&spi->dev, "chip select gpio is not specified or "
+					"invalid\n");
+		kfree(cs);
+		return ERR_PTR(-EINVAL);
+	}
+
+	of_property_read_u32(data_np, "samsung,spi-feedback-delay", &fb_delay);
+	cs->fb_delay = fb_delay;
+	return cs;
+}
+
 /*
  * Here we only check the validity of requested configuration
  * and save the configuration in a local data-structure.
@@ -813,14 +880,30 @@ static int s3c64xx_spi_setup(struct spi_device *spi)
 	struct s3c64xx_spi_info *sci;
 	struct spi_message *msg;
 	unsigned long flags;
-	int err = 0;
+	int err;
 
-	if (cs == NULL || cs->set_level == NULL) {
+	sdd = spi_master_get_devdata(spi->master);
+	if (!cs && spi->dev.of_node) {
+		cs = s3c64xx_get_slave_ctrldata(sdd, spi);
+		spi->controller_data = cs;
+	}
+
+	if (IS_ERR_OR_NULL(cs)) {
 		dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select);
 		return -ENODEV;
 	}
 
-	sdd = spi_master_get_devdata(spi->master);
+	if (!spi_get_ctldata(spi)) {
+		err = gpio_request(cs->line, dev_name(&spi->dev));
+		if (err) {
+			dev_err(&spi->dev, "request for slave select gpio "
+					"line [%d] failed\n", cs->line);
+			err = -EBUSY;
+			goto err_gpio_req;
+		}
+		spi_set_ctldata(spi, cs);
+	}
+
 	sci = sdd->cntrlr_info;
 
 	spin_lock_irqsave(&sdd->lock, flags);
@@ -831,7 +914,8 @@ static int s3c64xx_spi_setup(struct spi_device *spi)
 			dev_err(&spi->dev,
 				"setup: attempt while mssg in queue!\n");
 			spin_unlock_irqrestore(&sdd->lock, flags);
-			return -EBUSY;
+			err = -EBUSY;
+			goto err_msgq;
 		}
 	}
 
@@ -849,7 +933,7 @@ static int s3c64xx_spi_setup(struct spi_device *spi)
 	pm_runtime_get_sync(&sdd->pdev->dev);
 
 	/* Check if we can provide the requested rate */
-	if (!sci->clk_from_cmu) {
+	if (!sdd->port_conf->clk_from_cmu) {
 		u32 psr, speed;
 
 		/* Max possible */
@@ -874,22 +958,44 @@ static int s3c64xx_spi_setup(struct spi_device *spi)
 		}
 
 		speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
-		if (spi->max_speed_hz >= speed)
+		if (spi->max_speed_hz >= speed) {
 			spi->max_speed_hz = speed;
-		else
+		} else {
 			err = -EINVAL;
+			goto setup_exit;
+		}
 	}
 
 	pm_runtime_put(&sdd->pdev->dev);
+	disable_cs(sdd, spi);
+	return 0;
 
 setup_exit:
-
 	/* setup() returns with device de-selected */
 	disable_cs(sdd, spi);
 
+err_msgq:
+	gpio_free(cs->line);
+	spi_set_ctldata(spi, NULL);
+
+err_gpio_req:
+	kfree(cs);
+
 	return err;
 }
 
+static void s3c64xx_spi_cleanup(struct spi_device *spi)
+{
+	struct s3c64xx_spi_csinfo *cs = spi_get_ctldata(spi);
+
+	if (cs) {
+		gpio_free(cs->line);
+		if (spi->dev.of_node)
+			kfree(cs);
+	}
+	spi_set_ctldata(spi, NULL);
+}
+
 static irqreturn_t s3c64xx_spi_irq(int irq, void *data)
 {
 	struct s3c64xx_spi_driver_data *sdd = data;
@@ -930,7 +1036,7 @@ static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel)
 	/* Disable Interrupts - we use Polling if not DMA mode */
 	writel(0, regs + S3C64XX_SPI_INT_EN);
 
-	if (!sci->clk_from_cmu)
+	if (!sdd->port_conf->clk_from_cmu)
 		writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
 				regs + S3C64XX_SPI_CLK_CFG);
 	writel(0, regs + S3C64XX_SPI_MODE_CFG);
@@ -951,40 +1057,164 @@ static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel)
 	flush_fifo(sdd);
 }
 
-static int __init s3c64xx_spi_probe(struct platform_device *pdev)
+static int __devinit s3c64xx_spi_get_dmares(
+			struct s3c64xx_spi_driver_data *sdd, bool tx)
+{
+	struct platform_device *pdev = sdd->pdev;
+	struct s3c64xx_spi_dma_data *dma_data;
+	struct property *prop;
+	struct resource *res;
+	char prop_name[15], *chan_str;
+
+	if (tx) {
+		dma_data = &sdd->tx_dma;
+		dma_data->direction = DMA_TO_DEVICE;
+		chan_str = "tx";
+	} else {
+		dma_data = &sdd->rx_dma;
+		dma_data->direction = DMA_FROM_DEVICE;
+		chan_str = "rx";
+	}
+
+	if (!sdd->pdev->dev.of_node) {
+		res = platform_get_resource(pdev, IORESOURCE_DMA, tx ? 0 : 1);
+		if (!res) {
+			dev_err(&pdev->dev, "Unable to get SPI-%s dma "
+					"resource\n", chan_str);
+			return -ENXIO;
+		}
+		dma_data->dmach = res->start;
+		return 0;
+	}
+
+	sprintf(prop_name, "%s-dma-channel", chan_str);
+	prop = of_find_property(pdev->dev.of_node, prop_name, NULL);
+	if (!prop) {
+		dev_err(&pdev->dev, "%s dma channel property not specified\n",
+					chan_str);
+		return -ENXIO;
+	}
+
+	dma_data->dmach = DMACH_DT_PROP;
+	dma_data->dma_prop = prop;
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static int s3c64xx_spi_parse_dt_gpio(struct s3c64xx_spi_driver_data *sdd)
+{
+	struct device *dev = &sdd->pdev->dev;
+	int idx, gpio, ret;
+
+	/* find gpios for mosi, miso and clock lines */
+	for (idx = 0; idx < 3; idx++) {
+		gpio = of_get_gpio(dev->of_node, idx);
+		if (!gpio_is_valid(gpio)) {
+			dev_err(dev, "invalid gpio[%d]: %d\n", idx, gpio);
+			goto free_gpio;
+		}
+
+		ret = gpio_request(gpio, "spi-bus");
+		if (ret) {
+			dev_err(dev, "gpio [%d] request failed\n", gpio);
+			goto free_gpio;
+		}
+	}
+	return 0;
+
+free_gpio:
+	while (--idx >= 0)
+		gpio_free(sdd->gpios[idx]);
+	return -EINVAL;
+}
+
+static void s3c64xx_spi_dt_gpio_free(struct s3c64xx_spi_driver_data *sdd)
+{
+	unsigned int idx;
+	for (idx = 0; idx < 3; idx++)
+		gpio_free(sdd->gpios[idx]);
+}
+
+static struct __devinit s3c64xx_spi_info * s3c64xx_spi_parse_dt(
+						struct device *dev)
 {
-	struct resource	*mem_res, *dmatx_res, *dmarx_res;
-	struct s3c64xx_spi_driver_data *sdd;
 	struct s3c64xx_spi_info *sci;
-	struct spi_master *master;
-	int ret, irq;
-	char clk_name[16];
+	u32 temp;
 
-	if (pdev->id < 0) {
-		dev_err(&pdev->dev,
-				"Invalid platform device id-%d\n", pdev->id);
-		return -ENODEV;
+	sci = devm_kzalloc(dev, sizeof(*sci), GFP_KERNEL);
+	if (!sci) {
+		dev_err(dev, "memory allocation for spi_info failed\n");
+		return ERR_PTR(-ENOMEM);
 	}
 
-	if (pdev->dev.platform_data == NULL) {
-		dev_err(&pdev->dev, "platform_data missing!\n");
-		return -ENODEV;
+	if (of_property_read_u32(dev->of_node, "samsung,spi-src-clk", &temp)) {
+		dev_warn(dev, "spi bus clock parent not specified, using "
+				"clock at index 0 as parent\n");
+		sci->src_clk_nr = 0;
+	} else {
+		sci->src_clk_nr = temp;
 	}
 
-	sci = pdev->dev.platform_data;
+	if (of_property_read_u32(dev->of_node, "num-cs", &temp)) {
+		dev_warn(dev, "number of chip select lines not specified, "
+				"assuming 1 chip select line\n");
+		sci->num_cs = 1;
+	} else {
+		sci->num_cs = temp;
+	}
+
+	return sci;
+}
+#else
+static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
+{
+	return dev->platform_data;
+}
+
+static int s3c64xx_spi_parse_dt_gpio(struct s3c64xx_spi_driver_data *sdd)
+{
+	return -EINVAL;
+}
 
-	/* Check for availability of necessary resource */
+static void s3c64xx_spi_dt_gpio_free(struct s3c64xx_spi_driver_data *sdd)
+{
+}
+#endif
 
-	dmatx_res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
-	if (dmatx_res == NULL) {
-		dev_err(&pdev->dev, "Unable to get SPI-Tx dma resource\n");
-		return -ENXIO;
+static const struct of_device_id s3c64xx_spi_dt_match[];
+
+static inline struct s3c64xx_spi_port_config *s3c64xx_spi_get_port_config(
+						struct platform_device *pdev)
+{
+#ifdef CONFIG_OF
+	if (pdev->dev.of_node) {
+		const struct of_device_id *match;
+		match = of_match_node(s3c64xx_spi_dt_match, pdev->dev.of_node);
+		return (struct s3c64xx_spi_port_config *)match->data;
 	}
+#endif
+	return (struct s3c64xx_spi_port_config *)
+			 platform_get_device_id(pdev)->driver_data;
+}
 
-	dmarx_res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
-	if (dmarx_res == NULL) {
-		dev_err(&pdev->dev, "Unable to get SPI-Rx dma resource\n");
-		return -ENXIO;
+static int __init s3c64xx_spi_probe(struct platform_device *pdev)
+{
+	struct resource	*mem_res;
+	struct s3c64xx_spi_driver_data *sdd;
+	struct s3c64xx_spi_info *sci = pdev->dev.platform_data;
+	struct spi_master *master;
+	int ret, irq;
+	char clk_name[16];
+
+	if (!sci && pdev->dev.of_node) {
+		sci = s3c64xx_spi_parse_dt(&pdev->dev);
+		if (IS_ERR(sci))
+			return PTR_ERR(sci);
+	}
+
+	if (!sci) {
+		dev_err(&pdev->dev, "platform_data missing!\n");
+		return -ENODEV;
 	}
 
 	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -1009,19 +1239,37 @@ static int __init s3c64xx_spi_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, master);
 
 	sdd = spi_master_get_devdata(master);
+	sdd->port_conf = s3c64xx_spi_get_port_config(pdev);
 	sdd->master = master;
 	sdd->cntrlr_info = sci;
 	sdd->pdev = pdev;
 	sdd->sfr_start = mem_res->start;
-	sdd->tx_dma.dmach = dmatx_res->start;
-	sdd->tx_dma.direction = DMA_MEM_TO_DEV;
-	sdd->rx_dma.dmach = dmarx_res->start;
-	sdd->rx_dma.direction = DMA_DEV_TO_MEM;
+	if (pdev->dev.of_node) {
+		ret = of_alias_get_id(pdev->dev.of_node, "spi");
+		if (ret < 0) {
+			dev_err(&pdev->dev, "failed to get alias id, "
+						"errno %d\n", ret);
+			goto err0;
+		}
+		sdd->port_id = ret;
+	} else {
+		sdd->port_id = pdev->id;
+	}
 
 	sdd->cur_bpw = 8;
 
-	master->bus_num = pdev->id;
+	ret = s3c64xx_spi_get_dmares(sdd, true);
+	if (ret)
+		goto err0;
+
+	ret = s3c64xx_spi_get_dmares(sdd, false);
+	if (ret)
+		goto err0;
+
+	master->dev.of_node = pdev->dev.of_node;
+	master->bus_num = sdd->port_id;
 	master->setup = s3c64xx_spi_setup;
+	master->cleanup = s3c64xx_spi_cleanup;
 	master->prepare_transfer_hardware = s3c64xx_spi_prepare_transfer;
 	master->transfer_one_message = s3c64xx_spi_transfer_one_message;
 	master->unprepare_transfer_hardware = s3c64xx_spi_unprepare_transfer;
@@ -1044,7 +1292,10 @@ static int __init s3c64xx_spi_probe(struct platform_device *pdev)
 		goto err1;
 	}
 
-	if (sci->cfg_gpio == NULL || sci->cfg_gpio(pdev)) {
+	if (!sci->cfg_gpio && pdev->dev.of_node) {
+		if (s3c64xx_spi_parse_dt_gpio(sdd))
+			return -EBUSY;
+	} else if (sci->cfg_gpio == NULL || sci->cfg_gpio()) {
 		dev_err(&pdev->dev, "Unable to config gpio\n");
 		ret = -EBUSY;
 		goto err2;
@@ -1080,7 +1331,7 @@ static int __init s3c64xx_spi_probe(struct platform_device *pdev)
 	}
 
 	/* Setup Deufult Mode */
-	s3c64xx_spi_hwinit(sdd, pdev->id);
+	s3c64xx_spi_hwinit(sdd, sdd->port_id);
 
 	spin_lock_init(&sdd->lock);
 	init_completion(&sdd->xfer_completion);
@@ -1105,7 +1356,7 @@ static int __init s3c64xx_spi_probe(struct platform_device *pdev)
 
 	dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d "
 					"with %d Slaves attached\n",
-					pdev->id, master->num_chipselect);
+					sdd->port_id, master->num_chipselect);
 	dev_dbg(&pdev->dev, "\tIOmem=[0x%x-0x%x]\tDMA=[Rx-%d, Tx-%d]\n",
 					mem_res->end, mem_res->start,
 					sdd->rx_dma.dmach, sdd->tx_dma.dmach);
@@ -1125,6 +1376,8 @@ err5:
 err4:
 	clk_put(sdd->clk);
 err3:
+	if (!sdd->cntrlr_info->cfg_gpio && pdev->dev.of_node)
+		s3c64xx_spi_dt_gpio_free(sdd);
 err2:
 	iounmap((void *) sdd->regs);
 err1:
@@ -1156,6 +1409,9 @@ static int s3c64xx_spi_remove(struct platform_device *pdev)
 	clk_disable(sdd->clk);
 	clk_put(sdd->clk);
 
+	if (!sdd->cntrlr_info->cfg_gpio && pdev->dev.of_node)
+		s3c64xx_spi_dt_gpio_free(sdd);
+
 	iounmap((void *) sdd->regs);
 
 	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -1180,6 +1436,9 @@ static int s3c64xx_spi_suspend(struct device *dev)
 	clk_disable(sdd->src_clk);
 	clk_disable(sdd->clk);
 
+	if (!sdd->cntrlr_info->cfg_gpio && dev->of_node)
+		s3c64xx_spi_dt_gpio_free(sdd);
+
 	sdd->cur_speed = 0; /* Output Clock is stopped */
 
 	return 0;
@@ -1187,18 +1446,20 @@ static int s3c64xx_spi_suspend(struct device *dev)
 
 static int s3c64xx_spi_resume(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
 	struct spi_master *master = spi_master_get(dev_get_drvdata(dev));
 	struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
 	struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
 
-	sci->cfg_gpio(pdev);
+	if (!sci->cfg_gpio && dev->of_node)
+		s3c64xx_spi_parse_dt_gpio(sdd);
+	else
+		sci->cfg_gpio();
 
 	/* Enable the clock */
 	clk_enable(sdd->src_clk);
 	clk_enable(sdd->clk);
 
-	s3c64xx_spi_hwinit(sdd, pdev->id);
+	s3c64xx_spi_hwinit(sdd, sdd->port_id);
 
 	spi_master_resume(master);
 
@@ -1236,13 +1497,89 @@ static const struct dev_pm_ops s3c64xx_spi_pm = {
 			   s3c64xx_spi_runtime_resume, NULL)
 };
 
+struct s3c64xx_spi_port_config s3c2443_spi_port_config = {
+	.fifo_lvl_mask	= { 0x7f },
+	.rx_lvl_offset	= 13,
+	.tx_st_done	= 21,
+	.high_speed	= true,
+};
+
+struct s3c64xx_spi_port_config s3c6410_spi_port_config = {
+	.fifo_lvl_mask	= { 0x7f, 0x7F },
+	.rx_lvl_offset	= 13,
+	.tx_st_done	= 21,
+};
+
+struct s3c64xx_spi_port_config s5p64x0_spi_port_config = {
+	.fifo_lvl_mask	= { 0x1ff, 0x7F },
+	.rx_lvl_offset	= 15,
+	.tx_st_done	= 25,
+};
+
+struct s3c64xx_spi_port_config s5pc100_spi_port_config = {
+	.fifo_lvl_mask	= { 0x7f, 0x7F },
+	.rx_lvl_offset	= 13,
+	.tx_st_done	= 21,
+	.high_speed	= true,
+};
+
+struct s3c64xx_spi_port_config s5pv210_spi_port_config = {
+	.fifo_lvl_mask	= { 0x1ff, 0x7F },
+	.rx_lvl_offset	= 15,
+	.tx_st_done	= 25,
+	.high_speed	= true,
+};
+
+struct s3c64xx_spi_port_config exynos4_spi_port_config = {
+	.fifo_lvl_mask	= { 0x1ff, 0x7F, 0x7F },
+	.rx_lvl_offset	= 15,
+	.tx_st_done	= 25,
+	.high_speed	= true,
+	.clk_from_cmu	= true,
+};
+
+static struct platform_device_id s3c64xx_spi_driver_ids[] = {
+	{
+		.name		= "s3c2443-spi",
+		.driver_data	= (kernel_ulong_t)&s3c2443_spi_port_config,
+	}, {
+		.name		= "s3c6410-spi",
+		.driver_data	= (kernel_ulong_t)&s3c6410_spi_port_config,
+	}, {
+		.name		= "s5p64x0-spi",
+		.driver_data	= (kernel_ulong_t)&s5p64x0_spi_port_config,
+	}, {
+		.name		= "s5pc100-spi",
+		.driver_data	= (kernel_ulong_t)&s5pc100_spi_port_config,
+	}, {
+		.name		= "s5pv210-spi",
+		.driver_data	= (kernel_ulong_t)&s5pv210_spi_port_config,
+	}, {
+		.name		= "exynos4210-spi",
+		.driver_data	= (kernel_ulong_t)&exynos4_spi_port_config,
+	},
+	{ },
+};
+
+#ifdef CONFIG_OF
+static const struct of_device_id s3c64xx_spi_dt_match[] = {
+	{ .compatible = "samsung,exynos4210-spi",
+			.data = (void *)&exynos4_spi_port_config,
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, s3c64xx_spi_dt_match);
+#endif /* CONFIG_OF */
+
 static struct platform_driver s3c64xx_spi_driver = {
 	.driver = {
 		.name	= "s3c64xx-spi",
 		.owner = THIS_MODULE,
 		.pm = &s3c64xx_spi_pm,
+		.of_match_table = of_match_ptr(s3c64xx_spi_dt_match),
 	},
 	.remove = s3c64xx_spi_remove,
+	.id_table = s3c64xx_spi_driver_ids,
 };
 MODULE_ALIAS("platform:s3c64xx-spi");