usb: musb: Use is_cppi_enabled() and tusb_dma_omap() instead of the ifdef

This patch makes use of the two function is_cppi_enabled() and
tusb_dma_omap() instead of the ifdef for the proper DMA implementation
setup code. It basically shifts the code right by one indention level
and adds a few line breaks once the chars are crossed.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

drivers/usb/musb/musb_gadget.c

@@ -357,47 +357,49 @@ static void txstate(struct musb *musb, struct musb_request *req)
 			}
 		}
 
-#elif defined(CONFIG_USB_TI_CPPI_DMA)
-		/* program endpoint CSR first, then setup DMA */
-		csr &= ~(MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_TXPKTRDY);
-		csr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_DMAMODE |
-		       MUSB_TXCSR_MODE;
-		musb_writew(epio, MUSB_TXCSR,
-			(MUSB_TXCSR_P_WZC_BITS & ~MUSB_TXCSR_P_UNDERRUN)
-				| csr);
-
-		/* ensure writebuffer is empty */
-		csr = musb_readw(epio, MUSB_TXCSR);
-
-		/* NOTE host side sets DMAENAB later than this; both are
-		 * OK since the transfer dma glue (between CPPI and Mentor
-		 * fifos) just tells CPPI it could start.  Data only moves
-		 * to the USB TX fifo when both fifos are ready.
-		 */
-
-		/* "mode" is irrelevant here; handle terminating ZLPs like
-		 * PIO does, since the hardware RNDIS mode seems unreliable
-		 * except for the last-packet-is-already-short case.
-		 */
-		use_dma = use_dma && c->channel_program(
-				musb_ep->dma, musb_ep->packet_sz,
-				0,
-				request->dma + request->actual,
-				request_size);
-		if (!use_dma) {
-			c->channel_release(musb_ep->dma);
-			musb_ep->dma = NULL;
-			csr &= ~MUSB_TXCSR_DMAENAB;
-			musb_writew(epio, MUSB_TXCSR, csr);
-			/* invariant: prequest->buf is non-null */
-		}
-#elif defined(CONFIG_USB_TUSB_OMAP_DMA)
-		use_dma = use_dma && c->channel_program(
-				musb_ep->dma, musb_ep->packet_sz,
-				request->zero,
-				request->dma + request->actual,
-				request_size);
 #endif
+		if (is_cppi_enabled()) {
+			/* program endpoint CSR first, then setup DMA */
+			csr &= ~(MUSB_TXCSR_P_UNDERRUN | MUSB_TXCSR_TXPKTRDY);
+			csr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_DMAMODE |
+				MUSB_TXCSR_MODE;
+			musb_writew(epio, MUSB_TXCSR, (MUSB_TXCSR_P_WZC_BITS &
+						~MUSB_TXCSR_P_UNDERRUN) | csr);
+
+			/* ensure writebuffer is empty */
+			csr = musb_readw(epio, MUSB_TXCSR);
+
+			/*
+			 * NOTE host side sets DMAENAB later than this; both are
+			 * OK since the transfer dma glue (between CPPI and
+			 * Mentor fifos) just tells CPPI it could start. Data
+			 * only moves to the USB TX fifo when both fifos are
+			 * ready.
+			 */
+			/*
+			 * "mode" is irrelevant here; handle terminating ZLPs
+			 * like PIO does, since the hardware RNDIS mode seems
+			 * unreliable except for the
+			 * last-packet-is-already-short case.
+			 */
+			use_dma = use_dma && c->channel_program(
+					musb_ep->dma, musb_ep->packet_sz,
+					0,
+					request->dma + request->actual,
+					request_size);
+			if (!use_dma) {
+				c->channel_release(musb_ep->dma);
+				musb_ep->dma = NULL;
+				csr &= ~MUSB_TXCSR_DMAENAB;
+				musb_writew(epio, MUSB_TXCSR, csr);
+				/* invariant: prequest->buf is non-null */
+			}
+		} else if (tusb_dma_omap())
+			use_dma = use_dma && c->channel_program(
+					musb_ep->dma, musb_ep->packet_sz,
+					request->zero,
+					request->dma + request->actual,
+					request_size);
 	}
 #endif