dmaengine/amba-pl08x: max_bytes_per_lli is TRANSFER_SIZE * src_width (not MIN(width))

max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.

Below is summary of mail exchange with them:

[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.

[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.

So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:

        Total transfer size
        ------------------- = 40
          <source width>

[Viresh] Will this change if source is 4 bytes and dest is 2?

[David] Yes - the calculation then becomes:

        Total transfer size
        ------------------- =20
          <source width>

Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.

This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

drivers/dma/amba-pl08x.c

@@ -604,23 +604,17 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 	bd.srcbus.buswidth = bd.srcbus.maxwidth;
 	bd.dstbus.buswidth = bd.dstbus.maxwidth;
 
-	/*
-	 * Bytes transferred == tsize * MIN(buswidths), not max(buswidths)
-	 */
-	max_bytes_per_lli = min(bd.srcbus.buswidth, bd.dstbus.buswidth) *
-		PL080_CONTROL_TRANSFER_SIZE_MASK;
-
 	/* We need to count this down to zero */
 	bd.remainder = txd->len;
 
 	pl08x_choose_master_bus(&bd, &mbus, &sbus, cctl);
 
-	dev_vdbg(&pl08x->adev->dev, "src=0x%08x%s/%u dst=0x%08x%s/%u len=%zu llimax=%zu\n",
+	dev_vdbg(&pl08x->adev->dev, "src=0x%08x%s/%u dst=0x%08x%s/%u len=%zu\n",
 		 bd.srcbus.addr, cctl & PL080_CONTROL_SRC_INCR ? "+" : "",
 		 bd.srcbus.buswidth,
 		 bd.dstbus.addr, cctl & PL080_CONTROL_DST_INCR ? "+" : "",
 		 bd.dstbus.buswidth,
-		 bd.remainder, max_bytes_per_lli);
+		 bd.remainder);
 	dev_vdbg(&pl08x->adev->dev, "mbus=%s sbus=%s\n",
 		 mbus == &bd.srcbus ? "src" : "dst",
 		 sbus == &bd.srcbus ? "src" : "dst");
@@ -660,6 +654,10 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 			sbus->buswidth = 1;
 		}
 
+		/* Bytes transferred = tsize * src width, not MIN(buswidths) */
+		max_bytes_per_lli = bd.srcbus.buswidth *
+			PL080_CONTROL_TRANSFER_SIZE_MASK;
+
 		/*
 		 * Make largest possible LLIs until less than one bus
 		 * width left