Merge branch 'linus' into core/locking

Merge reason: Update to almost-final-.36

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Documentation/networking/e1000.txt

@@ -1,82 +1,35 @@
 Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
 ===============================================================
 
-September 26, 2006
-
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
 
 Contents
 ========
 
-- In This Release
 - Identifying Your Adapter
-- Building and Installation
 - Command Line Parameters
 - Speed and Duplex Configuration
 - Additional Configurations
-- Known Issues
 - Support
 
-
-In This Release
-===============
-
-This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
-of Adapters.  This driver includes support for Itanium(R)2-based systems.
-
-For questions related to hardware requirements, refer to the documentation
-supplied with your Intel PRO/1000 adapter. All hardware requirements listed
-apply to use with Linux.
-
-The following features are now available in supported kernels:
- - Native VLANs
- - Channel Bonding (teaming)
- - SNMP
-
-Channel Bonding documentation can be found in the Linux kernel source:
-/Documentation/networking/bonding.txt
-
-The driver information previously displayed in the /proc filesystem is not
-supported in this release.  Alternatively, you can use ethtool (version 1.6
-or later), lspci, and ifconfig to obtain the same information.
-
-Instructions on updating ethtool can be found in the section "Additional
-Configurations" later in this document.
-
-NOTE: The Intel(R) 82562v 10/100 Network Connection only provides 10/100
-support.
-
-
 Identifying Your Adapter
 ========================
 
 For more information on how to identify your adapter, go to the Adapter &
 Driver ID Guide at:
 
-    http://support.intel.com/support/network/adapter/pro100/21397.htm
+    http://support.intel.com/support/go/network/adapter/idguide.htm
 
 For the latest Intel network drivers for Linux, refer to the following
 website.  In the search field, enter your adapter name or type, or use the
 networking link on the left to search for your adapter:
 
-    http://downloadfinder.intel.com/scripts-df/support_intel.asp
-
+    http://support.intel.com/support/go/network/adapter/home.htm
 
 Command Line Parameters
 =======================
 
-If the driver is built as a module, the  following optional parameters
-are used by entering them on the command line with the modprobe command
-using this syntax:
-
-     modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
-
-For example, with two PRO/1000 PCI adapters, entering:
-
-     modprobe e1000 TxDescriptors=80,128
-
-loads the e1000 driver with 80 TX descriptors for the first adapter and
-128 TX descriptors for the second adapter.
-
 The default value for each parameter is generally the recommended setting,
 unless otherwise noted.
 
@@ -89,10 +42,6 @@ NOTES:  For more information about the AutoNeg, Duplex, and Speed
         parameters, see the application note at:
         http://www.intel.com/design/network/applnots/ap450.htm
 
-        A descriptor describes a data buffer and attributes related to
-        the data buffer.  This information is accessed by the hardware.
-
-
 AutoNeg
 -------
 (Supported only on adapters with copper connections)
@@ -106,7 +55,6 @@ Duplex parameters must not be specified.
 NOTE:  Refer to the Speed and Duplex section of this readme for more
        information on the AutoNeg parameter.
 
-
 Duplex
 ------
 (Supported only on adapters with copper connections)
@@ -119,7 +67,6 @@ set to auto-negotiate, the board auto-detects the correct duplex.  If the
 link partner is forced (either full or half), Duplex defaults to half-
 duplex.
 
-
 FlowControl
 -----------
 Valid Range:   0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
@@ -128,16 +75,16 @@ Default Value: Reads flow control settings from the EEPROM
 This parameter controls the automatic generation(Tx) and response(Rx)
 to Ethernet PAUSE frames.
 
-
 InterruptThrottleRate
 ---------------------
 (not supported on Intel(R) 82542, 82543 or 82544-based adapters)
-Valid Range:   0,1,3,100-100000 (0=off, 1=dynamic, 3=dynamic conservative)
+Valid Range:   0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+                                   4=simplified balancing)
 Default Value: 3
 
 The driver can limit the amount of interrupts per second that the adapter
-will generate for incoming packets. It does this by writing a value to the 
-adapter that is based on the maximum amount of interrupts that the adapter 
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
 will generate per second.
 
 Setting InterruptThrottleRate to a value greater or equal to 100
@@ -146,37 +93,43 @@ per second, even if more packets have come in. This reduces interrupt
 load on the system and can lower CPU utilization under heavy load,
 but will increase latency as packets are not processed as quickly.
 
-The default behaviour of the driver previously assumed a static 
-InterruptThrottleRate value of 8000, providing a good fallback value for 
-all traffic types,but lacking in small packet performance and latency. 
-The hardware can handle many more small packets per second however, and 
+The default behaviour of the driver previously assumed a static
+InterruptThrottleRate value of 8000, providing a good fallback value for
+all traffic types,but lacking in small packet performance and latency.
+The hardware can handle many more small packets per second however, and
 for this reason an adaptive interrupt moderation algorithm was implemented.
 
 Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which
-it dynamically adjusts the InterruptThrottleRate value based on the traffic 
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
 that it receives. After determining the type of incoming traffic in the last
-timeframe, it will adjust the InterruptThrottleRate to an appropriate value 
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
 for that traffic.
 
 The algorithm classifies the incoming traffic every interval into
-classes.  Once the class is determined, the InterruptThrottleRate value is 
-adjusted to suit that traffic type the best. There are three classes defined: 
+classes.  Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
 "Bulk traffic", for large amounts of packets of normal size; "Low latency",
 for small amounts of traffic and/or a significant percentage of small
-packets; and "Lowest latency", for almost completely small packets or 
+packets; and "Lowest latency", for almost completely small packets or
 minimal traffic.
 
-In dynamic conservative mode, the InterruptThrottleRate value is set to 4000 
-for traffic that falls in class "Bulk traffic". If traffic falls in the "Low 
-latency" or "Lowest latency" class, the InterruptThrottleRate is increased 
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
 stepwise to 20000. This default mode is suitable for most applications.
 
 For situations where low latency is vital such as cluster or
 grid computing, the algorithm can reduce latency even more when
 InterruptThrottleRate is set to mode 1. In this mode, which operates
-the same as mode 3, the InterruptThrottleRate will be increased stepwise to 
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
 70000 for traffic in class "Lowest latency".
 
+In simplified mode the interrupt rate is based on the ratio of Tx and
+Rx traffic.  If the bytes per second rate is approximately equal, the
+interrupt rate will drop as low as 2000 interrupts per second.  If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
+
 Setting InterruptThrottleRate to 0 turns off any interrupt moderation
 and may improve small packet latency, but is generally not suitable
 for bulk throughput traffic.
@@ -212,8 +165,6 @@ NOTE:  When e1000 is loaded with default settings and multiple adapters
        be platform-specific.  If CPU utilization is not a concern, use
        RX_POLLING (NAPI) and default driver settings.
 
-
-
 RxDescriptors
 -------------
 Valid Range:   80-256 for 82542 and 82543-based adapters
@@ -225,15 +176,14 @@ by the driver.  Increasing this value allows the driver to buffer more
 incoming packets, at the expense of increased system memory utilization.
 
 Each descriptor is 16 bytes.  A receive buffer is also allocated for each
-descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending 
+descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
 on the MTU setting. The maximum MTU size is 16110.
 
-NOTE:  MTU designates the frame size.  It only needs to be set for Jumbo 
-       Frames.  Depending on the available system resources, the request 
-       for a higher number of receive descriptors may be denied.  In this 
+NOTE:  MTU designates the frame size.  It only needs to be set for Jumbo
+       Frames.  Depending on the available system resources, the request
+       for a higher number of receive descriptors may be denied.  In this
        case, use a lower number.
 
-
 RxIntDelay
 ----------
 Valid Range:   0-65535 (0=off)
@@ -254,7 +204,6 @@ CAUTION:  When setting RxIntDelay to a value other than 0, adapters may
           restoring the network connection.  To eliminate the potential
           for the hang ensure that RxIntDelay is set to 0.
 
-
 RxAbsIntDelay
 -------------
 (This parameter is supported only on 82540, 82545 and later adapters.)
@@ -268,7 +217,6 @@ packet is received within the set amount of time.  Proper tuning,
 along with RxIntDelay, may improve traffic throughput in specific network
 conditions.
 
-
 Speed
 -----
 (This parameter is supported only on adapters with copper connections.)
@@ -280,7 +228,6 @@ Speed forces the line speed to the specified value in megabits per second
 partner is set to auto-negotiate, the board will auto-detect the correct
 speed.  Duplex should also be set when Speed is set to either 10 or 100.
 
-
 TxDescriptors
 -------------
 Valid Range:   80-256 for 82542 and 82543-based adapters
@@ -295,6 +242,36 @@ NOTE:  Depending on the available system resources, the request for a
        higher number of transmit descriptors may be denied.  In this case,
        use a lower number.
 
+TxDescriptorStep
+----------------
+Valid Range:    1 (use every Tx Descriptor)
+		4 (use every 4th Tx Descriptor)
+
+Default Value:  1 (use every Tx Descriptor)
+
+On certain non-Intel architectures, it has been observed that intense TX
+traffic bursts of short packets may result in an improper descriptor
+writeback. If this occurs, the driver will report a "TX Timeout" and reset
+the adapter, after which the transmit flow will restart, though data may
+have stalled for as much as 10 seconds before it resumes.
+
+The improper writeback does not occur on the first descriptor in a system
+memory cache-line, which is typically 32 bytes, or 4 descriptors long.
+
+Setting TxDescriptorStep to a value of 4 will ensure that all TX descriptors
+are aligned to the start of a system memory cache line, and so this problem
+will not occur.
+
+NOTES: Setting TxDescriptorStep to 4 effectively reduces the number of
+       TxDescriptors available for transmits to 1/4 of the normal allocation.
+       This has a possible negative performance impact, which may be
+       compensated for by allocating more descriptors using the TxDescriptors
+       module parameter.
+
+       There are other conditions which may result in "TX Timeout", which will
+       not be resolved by the use of the TxDescriptorStep parameter. As the
+       issue addressed by this parameter has never been observed on Intel
+       Architecture platforms, it should not be used on Intel platforms.
 
 TxIntDelay
 ----------
@@ -307,7 +284,6 @@ efficiency if properly tuned for specific network traffic.  If the
 system is reporting dropped transmits, this value may be set too high
 causing the driver to run out of available transmit descriptors.
 
-
 TxAbsIntDelay
 -------------
 (This parameter is supported only on 82540, 82545 and later adapters.)
@@ -330,6 +306,35 @@ Default Value: 1
 A value of '1' indicates that the driver should enable IP checksum
 offload for received packets (both UDP and TCP) to the adapter hardware.
 
+Copybreak
+---------
+Valid Range:   0-xxxxxxx (0=off)
+Default Value: 256
+Usage: insmod e1000.ko copybreak=128
+
+Driver copies all packets below or equaling this size to a fresh Rx
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value:  0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can turn off
+this parameter in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
 
 Speed and Duplex Configuration
 ==============================
@@ -385,40 +390,9 @@ If the link partner is forced to a specific speed and duplex, then this
 parameter should not be used.  Instead, use the Speed and Duplex parameters
 previously mentioned to force the adapter to the same speed and duplex.
 
-
 Additional Configurations
 =========================
 
-  Configuring the Driver on Different Distributions
-  -------------------------------------------------
-  Configuring a network driver to load properly when the system is started
-  is distribution dependent.  Typically, the configuration process involves
-  adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
-  as editing other system startup scripts and/or configuration files.  Many
-  popular Linux distributions ship with tools to make these changes for you.
-  To learn the proper way to configure a network device for your system,
-  refer to your distribution documentation.  If during this process you are
-  asked for the driver or module name, the name for the Linux Base Driver
-  for the Intel(R) PRO/1000 Family of Adapters is e1000.
-
-  As an example, if you install the e1000 driver for two PRO/1000 adapters
-  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add
-  the following to modules.conf or or modprobe.conf:
-
-       alias eth0 e1000
-       alias eth1 e1000
-       options e1000 Speed=10,100 Duplex=2,1
-
-  Viewing Link Messages
-  ---------------------
-  Link messages will not be displayed to the console if the distribution is
-  restricting system messages.  In order to see network driver link messages
-  on your console, set dmesg to eight by entering the following:
-
-       dmesg -n 8
-
-  NOTE: This setting is not saved across reboots.
-
   Jumbo Frames
   ------------
   Jumbo Frames support is enabled by changing the MTU to a value larger than
@@ -437,9 +411,11 @@ Additional Configurations
    setting in a different location.
 
   Notes:
-
-  - To enable Jumbo Frames, increase the MTU size on the interface beyond
-    1500.
+  Degradation in throughput performance may be observed in some Jumbo frames
+  environments. If this is observed, increasing the application's socket buffer
+  size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
+  See the specific application manual and /usr/src/linux*/Documentation/
+  networking/ip-sysctl.txt for more details.
 
   - The maximum MTU setting for Jumbo Frames is 16110.  This value coincides
     with the maximum Jumbo Frames size of 16128.
@@ -447,40 +423,11 @@ Additional Configurations
   - Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
     loss of link.
 
-  - Some Intel gigabit adapters that support Jumbo Frames have a frame size
-    limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
-    The adapters with this limitation are based on the Intel(R) 82571EB,
-    82572EI, 82573L and 80003ES2LAN controller.  These correspond to the
-    following product names:
-     Intel(R) PRO/1000 PT Server Adapter
-     Intel(R) PRO/1000 PT Desktop Adapter
-     Intel(R) PRO/1000 PT Network Connection
-     Intel(R) PRO/1000 PT Dual Port Server Adapter
-     Intel(R) PRO/1000 PT Dual Port Network Connection
-     Intel(R) PRO/1000 PF Server Adapter
-     Intel(R) PRO/1000 PF Network Connection
-     Intel(R) PRO/1000 PF Dual Port Server Adapter
-     Intel(R) PRO/1000 PB Server Connection
-     Intel(R) PRO/1000 PL Network Connection
-     Intel(R) PRO/1000 EB Network Connection with I/O Acceleration
-     Intel(R) PRO/1000 EB Backplane Connection with I/O Acceleration
-     Intel(R) PRO/1000 PT Quad Port Server Adapter
-
   - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
     support Jumbo Frames. These correspond to the following product names:
      Intel(R) PRO/1000 Gigabit Server Adapter
      Intel(R) PRO/1000 PM Network Connection
 
-  - The following adapters do not support Jumbo Frames:
-     Intel(R) 82562V 10/100 Network Connection
-     Intel(R) 82566DM Gigabit Network Connection
-     Intel(R) 82566DC Gigabit Network Connection
-     Intel(R) 82566MM Gigabit Network Connection
-     Intel(R) 82566MC Gigabit Network Connection
-     Intel(R) 82562GT 10/100 Network Connection
-     Intel(R) 82562G 10/100 Network Connection
-
-
   Ethtool
   -------
   The driver utilizes the ethtool interface for driver configuration and
@@ -490,142 +437,14 @@ Additional Configurations
   The latest release of ethtool can be found from
   http://sourceforge.net/projects/gkernel.
 
-  NOTE: Ethtool 1.6 only supports a limited set of ethtool options.  Support
-  for a more complete ethtool feature set can be enabled by upgrading
-  ethtool to ethtool-1.8.1.
-
   Enabling Wake on LAN* (WoL)
   ---------------------------
-  WoL is configured through the Ethtool* utility.  Ethtool is included with
-  all versions of Red Hat after Red Hat 7.2.  For other Linux distributions,
-  download and install Ethtool from the following website:
-  http://sourceforge.net/projects/gkernel.
-
-  For instructions on enabling WoL with Ethtool, refer to the website listed
-  above.
+  WoL is configured through the Ethtool* utility.
 
   WoL will be enabled on the system during the next shut down or reboot.
   For this driver version, in order to enable WoL, the e1000 driver must be
   loaded when shutting down or rebooting the system.
 
-  Wake On LAN is only supported on port A for the following devices:
-  Intel(R) PRO/1000 PT Dual Port Network Connection
-  Intel(R) PRO/1000 PT Dual Port Server Connection
-  Intel(R) PRO/1000 PT Dual Port Server Adapter
-  Intel(R) PRO/1000 PF Dual Port Server Adapter
-  Intel(R) PRO/1000 PT Quad Port Server Adapter
-
-  NAPI
-  ----
-  NAPI (Rx polling mode) is enabled in the e1000 driver.
-
-  See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
-
-
-Known Issues
-============
-
-Dropped Receive Packets on Half-duplex 10/100 Networks
-------------------------------------------------------
-If you have an Intel PCI Express adapter running at 10mbps or 100mbps, half-
-duplex, you may observe occasional dropped receive packets.  There are no
-workarounds for this problem in this network configuration.  The network must
-be updated to operate in full-duplex, and/or 1000mbps only.
-
-Jumbo Frames System Requirement
--------------------------------
-Memory allocation failures have been observed on Linux systems with 64 MB
-of RAM or less that are running Jumbo Frames.  If you are using Jumbo
-Frames, your system may require more than the advertised minimum
-requirement of 64 MB of system memory.
-
-Performance Degradation with Jumbo Frames
------------------------------------------
-Degradation in throughput performance may be observed in some Jumbo frames
-environments.  If this is observed, increasing the application's socket
-buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
-may help.  See the specific application manual and
-/usr/src/linux*/Documentation/
-networking/ip-sysctl.txt for more details.
-
-Jumbo Frames on Foundry BigIron 8000 switch
--------------------------------------------
-There is a known issue using Jumbo frames when connected to a Foundry
-BigIron 8000 switch.  This is a 3rd party limitation.  If you experience
-loss of packets, lower the MTU size.
-
-Allocating Rx Buffers when Using Jumbo Frames 
----------------------------------------------
-Allocating Rx buffers when using Jumbo Frames on 2.6.x kernels may fail if 
-the available memory is heavily fragmented. This issue may be seen with PCI-X 
-adapters or with packet split disabled. This can be reduced or eliminated 
-by changing the amount of available memory for receive buffer allocation, by
-increasing /proc/sys/vm/min_free_kbytes. 
-
-Multiple Interfaces on Same Ethernet Broadcast Network
-------------------------------------------------------
-Due to the default ARP behavior on Linux, it is not possible to have
-one system on two IP networks in the same Ethernet broadcast domain
-(non-partitioned switch) behave as expected.  All Ethernet interfaces
-will respond to IP traffic for any IP address assigned to the system.
-This results in unbalanced receive traffic.
-
-If you have multiple interfaces in a server, either turn on ARP
-filtering by entering:
-
-    echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
-(this only works if your kernel's version is higher than 2.4.5),
-
-NOTE: This setting is not saved across reboots.  The configuration
-change can be made permanent by adding the line:
-    net.ipv4.conf.all.arp_filter = 1
-to the file /etc/sysctl.conf
-
-      or,
-
-install the interfaces in separate broadcast domains (either in
-different switches or in a switch partitioned to VLANs).
-
-82541/82547 can't link or are slow to link with some link partners
------------------------------------------------------------------
-There is a known compatibility issue with 82541/82547 and some
-low-end switches where the link will not be established, or will
-be slow to establish.  In particular, these switches are known to
-be incompatible with 82541/82547:
-
-    Planex FXG-08TE
-    I-O Data ETG-SH8
-
-To workaround this issue, the driver can be compiled with an override
-of the PHY's master/slave setting.  Forcing master or forcing slave
-mode will improve time-to-link.
-
-    # make CFLAGS_EXTRA=-DE1000_MASTER_SLAVE=<n>
-
-Where <n> is:
-
-    0 = Hardware default
-    1 = Master mode
-    2 = Slave mode
-    3 = Auto master/slave
-
-Disable rx flow control with ethtool
-------------------------------------
-In order to disable receive flow control using ethtool, you must turn
-off auto-negotiation on the same command line.
-
-For example:
-
-   ethtool -A eth? autoneg off rx off
-
-Unplugging network cable while ethtool -p is running
-----------------------------------------------------
-In kernel versions 2.5.50 and later (including 2.6 kernel), unplugging
-the network cable while ethtool -p is running will cause the system to
-become unresponsive to keyboard commands, except for control-alt-delete.
-Restarting the system appears to be the only remedy.
-
-
 Support
 =======
 

Documentation/networking/e1000e.txt

@@ -0,0 +1,302 @@
+Linux* Driver for Intel(R) Network Connection
+===============================================================
+
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
+
+Contents
+========
+
+- Identifying Your Adapter
+- Command Line Parameters
+- Additional Configurations
+- Support
+
+Identifying Your Adapter
+========================
+
+The e1000e driver supports all PCI Express Intel(R) Gigabit Network
+Connections, except those that are 82575, 82576 and 82580-based*.
+
+* NOTE: The Intel(R) PRO/1000 P Dual Port Server Adapter is supported by
+  the e1000 driver, not the e1000e driver due to the 82546 part being used
+  behind a PCI Express bridge.
+
+For more information on how to identify your adapter, go to the Adapter &
+Driver ID Guide at:
+
+    http://support.intel.com/support/go/network/adapter/idguide.htm
+
+For the latest Intel network drivers for Linux, refer to the following
+website.  In the search field, enter your adapter name or type, or use the
+networking link on the left to search for your adapter:
+
+    http://support.intel.com/support/go/network/adapter/home.htm
+
+Command Line Parameters
+=======================
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+NOTES:  For more information about the InterruptThrottleRate,
+        RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
+        parameters, see the application note at:
+        http://www.intel.com/design/network/applnots/ap450.htm
+
+InterruptThrottleRate
+---------------------
+Valid Range:   0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+                                   4=simplified balancing)
+Default Value: 3
+
+The driver can limit the amount of interrupts per second that the adapter
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
+will generate per second.
+
+Setting InterruptThrottleRate to a value greater or equal to 100
+will program the adapter to send out a maximum of that many interrupts
+per second, even if more packets have come in. This reduces interrupt
+load on the system and can lower CPU utilization under heavy load,
+but will increase latency as packets are not processed as quickly.
+
+The driver has two adaptive modes (setting 1 or 3) in which
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
+that it receives. After determining the type of incoming traffic in the last
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
+for that traffic.
+
+The algorithm classifies the incoming traffic every interval into
+classes.  Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
+"Bulk traffic", for large amounts of packets of normal size; "Low latency",
+for small amounts of traffic and/or a significant percentage of small
+packets; and "Lowest latency", for almost completely small packets or
+minimal traffic.
+
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
+stepwise to 20000. This default mode is suitable for most applications.
+
+For situations where low latency is vital such as cluster or
+grid computing, the algorithm can reduce latency even more when
+InterruptThrottleRate is set to mode 1. In this mode, which operates
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
+70000 for traffic in class "Lowest latency".
+
+In simplified mode the interrupt rate is based on the ratio of Tx and
+Rx traffic.  If the bytes per second rate is approximately equal the
+interrupt rate will drop as low as 2000 interrupts per second.  If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
+
+Setting InterruptThrottleRate to 0 turns off any interrupt moderation
+and may improve small packet latency, but is generally not suitable
+for bulk throughput traffic.
+
+NOTE:  InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+       RxAbsIntDelay parameters.  In other words, minimizing the receive
+       and/or transmit absolute delays does not force the controller to
+       generate more interrupts than what the Interrupt Throttle Rate
+       allows.
+
+NOTE:  When e1000e is loaded with default settings and multiple adapters
+       are in use simultaneously, the CPU utilization may increase non-
+       linearly.  In order to limit the CPU utilization without impacting
+       the overall throughput, we recommend that you load the driver as
+       follows:
+
+           modprobe e1000e InterruptThrottleRate=3000,3000,3000
+
+       This sets the InterruptThrottleRate to 3000 interrupts/sec for
+       the first, second, and third instances of the driver.  The range
+       of 2000 to 3000 interrupts per second works on a majority of
+       systems and is a good starting point, but the optimal value will
+       be platform-specific.  If CPU utilization is not a concern, use
+       RX_POLLING (NAPI) and default driver settings.
+
+RxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 0
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds.  Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic.  Increasing this value adds
+extra latency to frame reception and can end up decreasing the throughput
+of TCP traffic.  If the system is reporting dropped receives, this value
+may be set too high, causing the driver to run out of available receive
+descriptors.
+
+CAUTION:  When setting RxIntDelay to a value other than 0, adapters may
+          hang (stop transmitting) under certain network conditions.  If
+          this occurs a NETDEV WATCHDOG message is logged in the system
+          event log.  In addition, the controller is automatically reset,
+          restoring the network connection.  To eliminate the potential
+          for the hang ensure that RxIntDelay is set to 0.
+
+RxAbsIntDelay
+-------------
+Valid Range:   0-65535 (0=off)
+Default Value: 8
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated.  Useful only if RxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is received within the set amount of time.  Proper tuning,
+along with RxIntDelay, may improve traffic throughput in specific network
+conditions.
+
+TxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 8
+
+This value delays the generation of transmit interrupts in units of
+1.024 microseconds.  Transmit interrupt reduction can improve CPU
+efficiency if properly tuned for specific network traffic.  If the
+system is reporting dropped transmits, this value may be set too high
+causing the driver to run out of available transmit descriptors.
+
+TxAbsIntDelay
+-------------
+Valid Range:   0-65535 (0=off)
+Default Value: 32
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated.  Useful only if TxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is sent on the wire within the set amount of time.  Proper tuning,
+along with TxIntDelay, may improve traffic throughput in specific
+network conditions.
+
+Copybreak
+---------
+Valid Range:   0-xxxxxxx (0=off)
+Default Value: 256
+
+Driver copies all packets below or equaling this size to a fresh Rx
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000e/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value:  0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can set this parameter
+in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
+
+IntMode
+-------
+Valid Range: 0-2 (0=legacy, 1=MSI, 2=MSI-X)
+Default Value: 2
+
+Allows changing the interrupt mode at module load time, without requiring a
+recompile. If the driver load fails to enable a specific interrupt mode, the
+driver will try other interrupt modes, from least to most compatible.  The
+interrupt order is MSI-X, MSI, Legacy.  If specifying MSI (IntMode=1)
+interrupts, only MSI and Legacy will be attempted.
+
+CrcStripping
+------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Strip the CRC from received packets before sending up the network stack.  If
+you have a machine with a BMC enabled but cannot receive IPMI traffic after
+loading or enabling the driver, try disabling this feature.
+
+WriteProtectNVM
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Set the hardware to ignore all write/erase cycles to the GbE region in the
+ICHx NVM (non-volatile memory).  This feature can be disabled by the
+WriteProtectNVM module parameter (enabled by default) only after a hardware
+reset, but the machine must be power cycled before trying to enable writes.
+
+Note: the kernel boot option iomem=relaxed may need to be set if the kernel
+config option CONFIG_STRICT_DEVMEM=y, if the root user wants to write the
+NVM from user space via ethtool.
+
+Additional Configurations
+=========================
+
+  Jumbo Frames
+  ------------
+  Jumbo Frames support is enabled by changing the MTU to a value larger than
+  the default of 1500.  Use the ifconfig command to increase the MTU size.
+  For example:
+
+       ifconfig eth<x> mtu 9000 up
+
+  This setting is not saved across reboots.
+
+  Notes:
+
+  - The maximum MTU setting for Jumbo Frames is 9216.  This value coincides
+    with the maximum Jumbo Frames size of 9234 bytes.
+
+  - Using Jumbo Frames at 10 or 100 Mbps is not supported and may result in
+    poor performance or loss of link.
+
+  - Some adapters limit Jumbo Frames sized packets to a maximum of
+    4096 bytes and some adapters do not support Jumbo Frames.
+
+
+  Ethtool
+  -------
+  The driver utilizes the ethtool interface for driver configuration and
+  diagnostics, as well as displaying statistical information.  We
+  strongly recommend downloading the latest version of Ethtool at:
+
+  http://sourceforge.net/projects/gkernel.
+
+  Speed and Duplex
+  ----------------
+  Speed and Duplex are configured through the Ethtool* utility. For
+  instructions,  refer to the Ethtool man page.
+
+  Enabling Wake on LAN* (WoL)
+  ---------------------------
+  WoL is configured through the Ethtool* utility. For instructions on
+  enabling WoL with Ethtool, refer to the Ethtool man page.
+
+  WoL will be enabled on the system during the next shut down or reboot.
+  For this driver version, in order to enable WoL, the e1000e driver must be
+  loaded when shutting down or rebooting the system.
+
+  In most cases Wake On LAN is only supported on port A for multiple port
+  adapters. To verify if a port supports Wake on LAN run ethtool eth<X>.
+
+
+Support
+=======
+
+For general information, go to the Intel support website at:
+
+    www.intel.com/support/
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
+If an issue is identified with the released source code on the supported
+kernel with a supported adapter, email the specific information related
+to the issue to e1000-devel@lists.sf.net

Documentation/networking/ixgbevf.txt

@@ -1,19 +1,16 @@
 Linux* Base Driver for Intel(R) Network Connection
 ==================================================
 
-November 24, 2009
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
 
 Contents
 ========
 
-- In This Release
 - Identifying Your Adapter
 - Known Issues/Troubleshooting
 - Support
 
-In This Release
-===============
-
 This file describes the ixgbevf Linux* Base Driver for Intel Network
 Connection.
 
@@ -33,7 +30,7 @@ Identifying Your Adapter
 For more information on how to identify your adapter, go to the Adapter &
 Driver ID Guide at:
 
-    http://support.intel.com/support/network/sb/CS-008441.htm
+    http://support.intel.com/support/go/network/adapter/idguide.htm
 
 Known Issues/Troubleshooting
 ============================
@@ -57,34 +54,3 @@ or the Intel Wired Networking project hosted by Sourceforge at:
 If an issue is identified with the released source code on the supported
 kernel with a supported adapter, email the specific information related
 to the issue to e1000-devel@lists.sf.net
-
-License
-=======
-
-Intel 10 Gigabit Linux driver.
-Copyright(c) 1999 - 2009 Intel Corporation.
-
-This program is free software; you can redistribute it and/or modify it
-under the terms and conditions of the GNU General Public License,
-version 2, as published by the Free Software Foundation.
-
-This program is distributed in the hope it will be useful, but WITHOUT
-ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
-more details.
-
-You should have received a copy of the GNU General Public License along with
-this program; if not, write to the Free Software Foundation, Inc.,
-51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
-
-The full GNU General Public License is included in this distribution in
-the file called "COPYING".
-
-Trademarks
-==========
-
-Intel, Itanium, and Pentium are trademarks or registered trademarks of
-Intel Corporation or its subsidiaries in the United States and other
-countries.
-
-* Other names and brands may be claimed as the property of others.

Documentation/vm/page-types.c

@@ -478,7 +478,7 @@ static void prepare_hwpoison_fd(void)
 	}
 
 	if (opt_unpoison && !hwpoison_forget_fd) {
-		sprintf(buf, "%s/renew-pfn", hwpoison_debug_fs);
+		sprintf(buf, "%s/unpoison-pfn", hwpoison_debug_fs);
 		hwpoison_forget_fd = checked_open(buf, O_WRONLY);
 	}
 }

MAINTAINERS

@@ -969,6 +969,16 @@ L:	linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-s5p*/
 
+ARM/SAMSUNG S5P SERIES FIMC SUPPORT
+M:	Kyungmin Park <kyungmin.park@samsung.com>
+M:	Sylwester Nawrocki <s.nawrocki@samsung.com>
+L:	linux-arm-kernel@lists.infradead.org
+L:	linux-media@vger.kernel.org
+S:	Maintained
+F:	arch/arm/plat-s5p/dev-fimc*
+F:	arch/arm/plat-samsung/include/plat/*fimc*
+F:	drivers/media/video/s5p-fimc/
+
 ARM/SHMOBILE ARM ARCHITECTURE
 M:	Paul Mundt <lethal@linux-sh.org>
 M:	Magnus Damm <magnus.damm@gmail.com>
@@ -2535,7 +2545,7 @@ S:	Supported
 F:	drivers/scsi/gdt*
 
 GENERIC GPIO I2C DRIVER
-M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
+M:	Haavard Skinnemoen <hskinnemoen@gmail.com>
 S:	Supported
 F:	drivers/i2c/busses/i2c-gpio.c
 F:	include/linux/i2c-gpio.h
@@ -3063,16 +3073,27 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ixp2000/
 
-INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe)
+INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe/ixgbevf)
 M:	Jeff Kirsher <jeffrey.t.kirsher@intel.com>
 M:	Jesse Brandeburg <jesse.brandeburg@intel.com>
 M:	Bruce Allan <bruce.w.allan@intel.com>
-M:	Alex Duyck <alexander.h.duyck@intel.com>
+M:	Carolyn Wyborny <carolyn.wyborny@intel.com>
+M:	Don Skidmore <donald.c.skidmore@intel.com>
+M:	Greg Rose <gregory.v.rose@intel.com>
 M:	PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
+M:	Alex Duyck <alexander.h.duyck@intel.com>
 M:	John Ronciak <john.ronciak@intel.com>
 L:	e1000-devel@lists.sourceforge.net
 W:	http://e1000.sourceforge.net/
 S:	Supported
+F:	Documentation/networking/e100.txt
+F:	Documentation/networking/e1000.txt
+F:	Documentation/networking/e1000e.txt
+F:	Documentation/networking/igb.txt
+F:	Documentation/networking/igbvf.txt
+F:	Documentation/networking/ixgb.txt
+F:	Documentation/networking/ixgbe.txt
+F:	Documentation/networking/ixgbevf.txt
 F:	drivers/net/e100.c
 F:	drivers/net/e1000/
 F:	drivers/net/e1000e/
@@ -3080,6 +3101,7 @@ F:	drivers/net/igb/
 F:	drivers/net/igbvf/
 F:	drivers/net/ixgb/
 F:	drivers/net/ixgbe/
+F:	drivers/net/ixgbevf/
 
 INTEL PRO/WIRELESS 2100 NETWORK CONNECTION SUPPORT
 L:	linux-wireless@vger.kernel.org
@@ -5008,6 +5030,12 @@ F:	drivers/media/common/saa7146*
 F:	drivers/media/video/*7146*
 F:	include/media/*7146*
 
+SAMSUNG AUDIO (ASoC) DRIVERS
+M:	Jassi Brar <jassi.brar@samsung.com>
+L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
+S:	Supported
+F:	sound/soc/s3c24xx
+
 TLG2300 VIDEO4LINUX-2 DRIVER
 M:	Huang Shijie <shijie8@gmail.com>
 M:	Kang Yong <kangyong@telegent.com>
@@ -6450,8 +6478,10 @@ F:	include/linux/wm97xx.h
 WOLFSON MICROELECTRONICS DRIVERS
 M:	Mark Brown <broonie@opensource.wolfsonmicro.com>
 M:	Ian Lartey <ian@opensource.wolfsonmicro.com>
+M:	Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
+T:	git git://opensource.wolfsonmicro.com/linux-2.6-asoc
 T:	git git://opensource.wolfsonmicro.com/linux-2.6-audioplus
-W:	http://opensource.wolfsonmicro.com/node/8
+W:	http://opensource.wolfsonmicro.com/content/linux-drivers-wolfson-devices
 S:	Supported
 F:	Documentation/hwmon/wm83??
 F:	drivers/leds/leds-wm83*.c

Makefile

@@ -1,8 +1,8 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 36
-EXTRAVERSION = -rc6
-NAME = Sheep on Meth
+EXTRAVERSION = -rc8
+NAME = Flesh-Eating Bats with Fangs
 
 # *DOCUMENTATION*
 # To see a list of typical targets execute "make help"

arch/arm/Kconfig

@@ -1101,6 +1101,20 @@ config ARM_ERRATA_720789
 	  invalidated are not, resulting in an incoherency in the system page
 	  tables. The workaround changes the TLB flushing routines to invalidate
 	  entries regardless of the ASID.
+
+config ARM_ERRATA_743622
+	bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption"
+	depends on CPU_V7
+	help
+	  This option enables the workaround for the 743622 Cortex-A9
+	  (r2p0..r2p2) erratum. Under very rare conditions, a faulty
+	  optimisation in the Cortex-A9 Store Buffer may lead to data
+	  corruption. This workaround sets a specific bit in the diagnostic
+	  register of the Cortex-A9 which disables the Store Buffer
+	  optimisation, preventing the defect from occurring. This has no
+	  visible impact on the overall performance or power consumption of the
+	  processor.
+
 endmenu
 
 source "arch/arm/common/Kconfig"

arch/arm/kernel/kprobes-decode.c

@@ -1162,11 +1162,12 @@ space_cccc_001x(kprobe_opcode_t insn, struct arch_specific_insn *asi)
 {
 	/*
 	 * MSR   : cccc 0011 0x10 xxxx xxxx xxxx xxxx xxxx
-	 * Undef : cccc 0011 0x00 xxxx xxxx xxxx xxxx xxxx
+	 * Undef : cccc 0011 0100 xxxx xxxx xxxx xxxx xxxx
 	 * ALU op with S bit and Rd == 15 :
 	 *	   cccc 001x xxx1 xxxx 1111 xxxx xxxx xxxx
 	 */
-	if ((insn & 0x0f900000) == 0x03200000 ||	/* MSR & Undef */
+	if ((insn & 0x0fb00000) == 0x03200000 ||	/* MSR */
+	    (insn & 0x0ff00000) == 0x03400000 ||	/* Undef */
 	    (insn & 0x0e10f000) == 0x0210f000)		/* ALU s-bit, R15  */
 		return INSN_REJECTED;
 
@@ -1177,7 +1178,7 @@ space_cccc_001x(kprobe_opcode_t insn, struct arch_specific_insn *asi)
 	 * *S (bit 20) updates condition codes
 	 * ADC/SBC/RSC reads the C flag
 	 */
-	insn &= 0xfff00fff;	/* Rn = r0, Rd = r0 */
+	insn &= 0xffff0fff;	/* Rd = r0 */
 	asi->insn[0] = insn;
 	asi->insn_handler = (insn & (1 << 20)) ?  /* S-bit */
 			emulate_alu_imm_rwflags : emulate_alu_imm_rflags;

arch/arm/mach-at91/include/mach/system.h

@@ -28,17 +28,16 @@
 
 static inline void arch_idle(void)
 {
-#ifndef CONFIG_DEBUG_KERNEL
 	/*
 	 * Disable the processor clock.  The processor will be automatically
 	 * re-enabled by an interrupt or by a reset.
 	 */
 	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
-#else
+#ifndef CONFIG_CPU_ARM920T
 	/*
 	 * Set the processor (CP15) into 'Wait for Interrupt' mode.
-	 * Unlike disabling the processor clock via the PMC (above)
-	 *  this allows the processor to be woken via JTAG.
+	 * Post-RM9200 processors need this in conjunction with the above
+	 * to save power when idle.
 	 */
 	cpu_do_idle();
 #endif

arch/arm/mach-ep93xx/dma-m2p.c

@@ -276,7 +276,7 @@ static void channel_disable(struct m2p_channel *ch)
 	v &= ~(M2P_CONTROL_STALL_IRQ_EN | M2P_CONTROL_NFB_IRQ_EN);
 	m2p_set_control(ch, v);
 
-	while (m2p_channel_state(ch) == STATE_ON)
+	while (m2p_channel_state(ch) >= STATE_ON)
 		cpu_relax();
 
 	m2p_set_control(ch, 0x0);

arch/arm/mach-imx/Kconfig

@@ -122,6 +122,7 @@ config MACH_CPUIMX27
 	select IMX_HAVE_PLATFORM_IMX_I2C
 	select IMX_HAVE_PLATFORM_IMX_UART
 	select IMX_HAVE_PLATFORM_MXC_NAND
+	select MXC_ULPI if USB_ULPI
 	help
 	  Include support for Eukrea CPUIMX27 platform. This includes
 	  specific configurations for the module and its peripherals.

arch/arm/mach-imx/mach-cpuimx27.c

@@ -259,7 +259,7 @@ static void __init eukrea_cpuimx27_init(void)
 	i2c_register_board_info(0, eukrea_cpuimx27_i2c_devices,
 				ARRAY_SIZE(eukrea_cpuimx27_i2c_devices));
 
-	imx27_add_i2c_imx1(&cpuimx27_i2c1_data);
+	imx27_add_i2c_imx0(&cpuimx27_i2c1_data);
 
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 

arch/arm/mach-s5p6440/cpu.c

@@ -19,6 +19,7 @@
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
+#include <linux/sched.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>

arch/arm/mach-s5p6442/cpu.c

@@ -19,6 +19,7 @@
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
+#include <linux/sched.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>

arch/arm/mach-s5pc100/cpu.c

@@ -21,6 +21,7 @@
 #include <linux/sysdev.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
+#include <linux/sched.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>

arch/arm/mach-s5pv210/clock.c

@@ -173,11 +173,6 @@ static int s5pv210_clk_ip3_ctrl(struct clk *clk, int enable)
 	return s5p_gatectrl(S5P_CLKGATE_IP3, clk, enable);
 }
 
-static int s5pv210_clk_ip4_ctrl(struct clk *clk, int enable)
-{
-	return s5p_gatectrl(S5P_CLKGATE_IP4, clk, enable);
-}
-
 static int s5pv210_clk_mask0_ctrl(struct clk *clk, int enable)
 {
 	return s5p_gatectrl(S5P_CLK_SRC_MASK0, clk, enable);

arch/arm/mach-s5pv210/cpu.c

@@ -19,6 +19,7 @@
 #include <linux/io.h>
 #include <linux/sysdev.h>
 #include <linux/platform_device.h>
+#include <linux/sched.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>

arch/arm/mach-vexpress/ct-ca9x4.c

@@ -68,7 +68,7 @@ static void __init ct_ca9x4_init_irq(void)
 }
 
 #if 0
-static void ct_ca9x4_timer_init(void)
+static void __init ct_ca9x4_timer_init(void)
 {
 	writel(0, MMIO_P2V(CT_CA9X4_TIMER0) + TIMER_CTRL);
 	writel(0, MMIO_P2V(CT_CA9X4_TIMER1) + TIMER_CTRL);
@@ -222,7 +222,7 @@ static struct platform_device pmu_device = {
 	.resource	= pmu_resources,
 };
 
-static void ct_ca9x4_init(void)
+static void __init ct_ca9x4_init(void)
 {
 	int i;
 

arch/arm/mach-vexpress/v2m.c

@@ -48,7 +48,7 @@ void __init v2m_map_io(struct map_desc *tile, size_t num)
 }
 
 
-static void v2m_timer_init(void)
+static void __init v2m_timer_init(void)
 {
 	writel(0, MMIO_P2V(V2M_TIMER0) + TIMER_CTRL);
 	writel(0, MMIO_P2V(V2M_TIMER1) + TIMER_CTRL);

arch/arm/mm/ioremap.c

@@ -204,8 +204,12 @@ void __iomem * __arm_ioremap_pfn_caller(unsigned long pfn,
 	/*
 	 * Don't allow RAM to be mapped - this causes problems with ARMv6+
 	 */
-	if (WARN_ON(pfn_valid(pfn)))
-		return NULL;
+	if (pfn_valid(pfn)) {
+		printk(KERN_WARNING "BUG: Your driver calls ioremap() on system memory.  This leads\n"
+		       KERN_WARNING "to architecturally unpredictable behaviour on ARMv6+, and ioremap()\n"
+		       KERN_WARNING "will fail in the next kernel release.  Please fix your driver.\n");
+		WARN_ON(1);
+	}
 
 	type = get_mem_type(mtype);
 	if (!type)

arch/arm/mm/mmu.c

@@ -248,7 +248,7 @@ static struct mem_type mem_types[] = {
 	},
 	[MT_MEMORY] = {
 		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
-				L_PTE_USER | L_PTE_EXEC,
+				L_PTE_WRITE | L_PTE_EXEC,
 		.prot_l1   = PMD_TYPE_TABLE,
 		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE,
 		.domain    = DOMAIN_KERNEL,
@@ -259,7 +259,7 @@ static struct mem_type mem_types[] = {
 	},
 	[MT_MEMORY_NONCACHED] = {
 		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
-				L_PTE_USER | L_PTE_EXEC | L_PTE_MT_BUFFERABLE,
+				L_PTE_WRITE | L_PTE_EXEC | L_PTE_MT_BUFFERABLE,
 		.prot_l1   = PMD_TYPE_TABLE,
 		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE,
 		.domain    = DOMAIN_KERNEL,

arch/arm/mm/proc-v7.S

@@ -253,6 +253,14 @@ __v7_setup:
 	orreq	r10, r10, #1 << 22		@ set bit #22
 	mcreq	p15, 0, r10, c15, c0, 1		@ write diagnostic register
 #endif
+#ifdef CONFIG_ARM_ERRATA_743622
+	teq	r6, #0x20			@ present in r2p0
+	teqne	r6, #0x21			@ present in r2p1
+	teqne	r6, #0x22			@ present in r2p2
+	mrceq	p15, 0, r10, c15, c0, 1		@ read diagnostic register
+	orreq	r10, r10, #1 << 6		@ set bit #6
+	mcreq	p15, 0, r10, c15, c0, 1		@ write diagnostic register
+#endif
 
 3:	mov	r10, #0
 #ifdef HARVARD_CACHE
@@ -365,7 +373,7 @@ __v7_ca9mp_proc_info:
 	b	__v7_ca9mp_setup
 	.long	cpu_arch_name
 	.long	cpu_elf_name
-	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP
+	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP|HWCAP_TLS
 	.long	cpu_v7_name
 	.long	v7_processor_functions
 	.long	v7wbi_tlb_fns

arch/arm/oprofile/common.c

@@ -102,6 +102,7 @@ static int op_create_counter(int cpu, int event)
 	if (IS_ERR(pevent)) {
 		ret = PTR_ERR(pevent);
 	} else if (pevent->state != PERF_EVENT_STATE_ACTIVE) {
+		perf_event_release_kernel(pevent);
 		pr_warning("oprofile: failed to enable event %d "
 				"on CPU %d\n", event, cpu);
 		ret = -EBUSY;
@@ -365,6 +366,7 @@ int __init oprofile_arch_init(struct oprofile_operations *ops)
 	ret = init_driverfs();
 	if (ret) {
 		kfree(counter_config);
+		counter_config = NULL;
 		return ret;
 	}
 
@@ -402,7 +404,6 @@ void oprofile_arch_exit(void)
 	struct perf_event *event;
 
 	if (*perf_events) {
-		exit_driverfs();
 		for_each_possible_cpu(cpu) {
 			for (id = 0; id < perf_num_counters; ++id) {
 				event = perf_events[cpu][id];
@@ -413,8 +414,10 @@ void oprofile_arch_exit(void)
 		}
 	}
 
-	if (counter_config)
+	if (counter_config) {
 		kfree(counter_config);
+		exit_driverfs();
+	}
 }
 #else
 int __init oprofile_arch_init(struct oprofile_operations *ops)

arch/arm/plat-omap/iommu.c

@@ -320,6 +320,7 @@ void flush_iotlb_page(struct iommu *obj, u32 da)
 		if ((start <= da) && (da < start + bytes)) {
 			dev_dbg(obj->dev, "%s: %08x<=%08x(%x)\n",
 				__func__, start, da, bytes);
+			iotlb_load_cr(obj, &cr);
 			iommu_write_reg(obj, 1, MMU_FLUSH_ENTRY);
 		}
 	}

arch/arm/plat-samsung/adc.c

@@ -435,7 +435,6 @@ static int s3c_adc_suspend(struct platform_device *pdev, pm_message_t state)
 static int s3c_adc_resume(struct platform_device *pdev)
 {
 	struct adc_device *adc = platform_get_drvdata(pdev);
-	unsigned long flags;
 
 	clk_enable(adc->clk);
 	enable_irq(adc->irq);

arch/arm/plat-samsung/clock.c

@@ -48,6 +48,9 @@
 #include <plat/clock.h>
 #include <plat/cpu.h>
 
+#include <linux/serial_core.h>
+#include <plat/regs-serial.h> /* for s3c24xx_uart_devs */
+
 /* clock information */
 
 static LIST_HEAD(clocks);
@@ -65,6 +68,28 @@ static int clk_null_enable(struct clk *clk, int enable)
 	return 0;
 }
 
+static int dev_is_s3c_uart(struct device *dev)
+{
+	struct platform_device **pdev = s3c24xx_uart_devs;
+	int i;
+	for (i = 0; i < ARRAY_SIZE(s3c24xx_uart_devs); i++, pdev++)
+		if (*pdev && dev == &(*pdev)->dev)
+			return 1;
+	return 0;
+}
+
+/*
+ * Serial drivers call get_clock() very early, before platform bus
+ * has been set up, this requires a special check to let them get
+ * a proper clock
+ */
+
+static int dev_is_platform_device(struct device *dev)
+{
+	return dev->bus == &platform_bus_type ||
+	       (dev->bus == NULL && dev_is_s3c_uart(dev));
+}
+
 /* Clock API calls */
 
 struct clk *clk_get(struct device *dev, const char *id)
@@ -73,7 +98,7 @@ struct clk *clk_get(struct device *dev, const char *id)
 	struct clk *clk = ERR_PTR(-ENOENT);
 	int idno;
 
-	if (dev == NULL || dev->bus != &platform_bus_type)
+	if (dev == NULL || !dev_is_platform_device(dev))
 		idno = -1;
 	else
 		idno = to_platform_device(dev)->id;

arch/avr32/kernel/module.c

@@ -314,10 +314,9 @@ int module_finalize(const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs,
 	vfree(module->arch.syminfo);
 	module->arch.syminfo = NULL;
 
-	return module_bug_finalize(hdr, sechdrs, module);
+	return 0;
 }
 
 void module_arch_cleanup(struct module *module)
 {
-	module_bug_cleanup(module);
 }

arch/h8300/kernel/module.c

@@ -112,10 +112,9 @@ int module_finalize(const Elf_Ehdr *hdr,
 		    const Elf_Shdr *sechdrs,
 		    struct module *me)
 {
-	return module_bug_finalize(hdr, sechdrs, me);
+	return 0;
 }
 
 void module_arch_cleanup(struct module *mod)
 {
-	module_bug_cleanup(mod);
 }

arch/m32r/include/asm/elf.h

@@ -82,9 +82,9 @@ typedef elf_fpreg_t elf_fpregset_t;
  * These are used to set parameters in the core dumps.
  */
 #define ELF_CLASS	ELFCLASS32
-#if defined(__LITTLE_ENDIAN)
+#if defined(__LITTLE_ENDIAN__)
 #define ELF_DATA	ELFDATA2LSB
-#elif defined(__BIG_ENDIAN)
+#elif defined(__BIG_ENDIAN__)
 #define ELF_DATA	ELFDATA2MSB
 #else
 #error no endian defined

arch/m32r/kernel/.gitignore

@@ -0,0 +1 @@
+vmlinux.lds

arch/m32r/kernel/signal.c

@@ -28,6 +28,8 @@
 
 #define DEBUG_SIG 0
 
+#define _BLOCKABLE (~(sigmask(SIGKILL) | sigmask(SIGSTOP)))
+
 asmlinkage int
 sys_sigaltstack(const stack_t __user *uss, stack_t __user *uoss,
 		unsigned long r2, unsigned long r3, unsigned long r4,
@@ -254,7 +256,7 @@ give_sigsegv:
 static int prev_insn(struct pt_regs *regs)
 {
 	u16 inst;
-	if (get_user(&inst, (u16 __user *)(regs->bpc - 2)))
+	if (get_user(inst, (u16 __user *)(regs->bpc - 2)))
 		return -EFAULT;
 	if ((inst & 0xfff0) == 0x10f0)	/* trap ? */
 		regs->bpc -= 2;

arch/mips/Kconfig

@@ -13,6 +13,7 @@ config MIPS
 	select HAVE_KPROBES
 	select HAVE_KRETPROBES
 	select RTC_LIB if !MACH_LOONGSON
+	select GENERIC_ATOMIC64 if !64BIT
 
 mainmenu "Linux/MIPS Kernel Configuration"
 
@@ -1646,8 +1647,16 @@ config MIPS_MT_SMP
 	select SYS_SUPPORTS_SMP
 	select SMP_UP
 	help
-	  This is a kernel model which is also known a VSMP or lately
-	  has been marketesed into SMVP.
+	  This is a kernel model which is known a VSMP but lately has been
+	  marketesed into SMVP.
+	  Virtual SMP uses the processor's VPEs  to implement virtual
+	  processors. In currently available configuration of the 34K processor
+	  this allows for a dual processor. Both processors will share the same
+	  primary caches; each will obtain the half of the TLB for it's own
+	  exclusive use. For a layman this model can be described as similar to
+	  what Intel calls Hyperthreading.
+
+	  For further information see http://www.linux-mips.org/wiki/34K#VSMP
 
 config MIPS_MT_SMTC
 	bool "SMTC: Use all TCs on all VPEs for SMP"
@@ -1664,6 +1673,14 @@ config MIPS_MT_SMTC
 	help
 	  This is a kernel model which is known a SMTC or lately has been
 	  marketesed into SMVP.
+	  is presenting the available TC's of the core as processors to Linux.
+	  On currently available 34K processors this means a Linux system will
+	  see up to 5 processors. The implementation of the SMTC kernel differs
+	  significantly from VSMP and cannot efficiently coexist in the same
+	  kernel binary so the choice between VSMP and SMTC is a compile time
+	  decision.
+
+	  For further information see http://www.linux-mips.org/wiki/34K#SMTC
 
 endchoice
 

arch/mips/alchemy/common/prom.c

@@ -43,7 +43,7 @@ int prom_argc;
 char **prom_argv;
 char **prom_envp;
 
-void prom_init_cmdline(void)
+void __init prom_init_cmdline(void)
 {
 	int i;
 
@@ -104,7 +104,7 @@ static inline void str2eaddr(unsigned char *ea, unsigned char *str)
 	}
 }
 
-int prom_get_ethernet_addr(char *ethernet_addr)
+int __init prom_get_ethernet_addr(char *ethernet_addr)
 {
 	char *ethaddr_str;
 
@@ -123,7 +123,6 @@ int prom_get_ethernet_addr(char *ethernet_addr)
 
 	return 0;
 }
-EXPORT_SYMBOL(prom_get_ethernet_addr);
 
 void __init prom_free_prom_memory(void)
 {

arch/mips/boot/compressed/Makefile

@@ -59,7 +59,7 @@ $(obj)/piggy.o: $(obj)/dummy.o $(obj)/vmlinux.bin.z FORCE
 hostprogs-y := calc_vmlinuz_load_addr
 
 VMLINUZ_LOAD_ADDRESS = $(shell $(obj)/calc_vmlinuz_load_addr \
-		$(objtree)/$(KBUILD_IMAGE) $(VMLINUX_LOAD_ADDRESS))
+		$(obj)/vmlinux.bin $(VMLINUX_LOAD_ADDRESS))
 
 vmlinuzobjs-y += $(obj)/piggy.o
 

arch/mips/cavium-octeon/Kconfig

@@ -83,3 +83,7 @@ config ARCH_SPARSEMEM_ENABLE
 	def_bool y
 	select SPARSEMEM_STATIC
 	depends on CPU_CAVIUM_OCTEON
+
+config CAVIUM_OCTEON_HELPER
+	def_bool y
+	depends on OCTEON_ETHERNET || PCI

arch/mips/cavium-octeon/cpu.c

@@ -41,7 +41,7 @@ static int cnmips_cu2_call(struct notifier_block *nfb, unsigned long action,
 	return NOTIFY_OK;		/* Let default notifier send signals */
 }
 
-static int cnmips_cu2_setup(void)
+static int __init cnmips_cu2_setup(void)
 {
 	return cu2_notifier(cnmips_cu2_call, 0);
 }

arch/mips/cavium-octeon/executive/Makefile

@@ -11,4 +11,4 @@
 
 obj-y += cvmx-bootmem.o cvmx-l2c.o cvmx-sysinfo.o octeon-model.o
 
-obj-$(CONFIG_PCI) += cvmx-helper-errata.o cvmx-helper-jtag.o
+obj-$(CONFIG_CAVIUM_OCTEON_HELPER) += cvmx-helper-errata.o cvmx-helper-jtag.o

arch/mips/include/asm/atomic.h

@@ -782,6 +782,10 @@ static __inline__ int atomic64_add_unless(atomic64_t *v, long a, long u)
  */
 #define atomic64_add_negative(i, v) (atomic64_add_return(i, (v)) < 0)
 
+#else /* !CONFIG_64BIT */
+
+#include <asm-generic/atomic64.h>
+
 #endif /* CONFIG_64BIT */
 
 /*

arch/mips/include/asm/cop2.h

@@ -24,7 +24,7 @@ extern int cu2_notifier_call_chain(unsigned long val, void *v);
 
 #define cu2_notifier(fn, pri)						\
 ({									\
-	static struct notifier_block fn##_nb __cpuinitdata = {		\
+	static struct notifier_block fn##_nb = {			\
 		.notifier_call = fn,					\
 		.priority = pri						\
 	};								\

arch/mips/include/asm/gic.h

@@ -321,6 +321,7 @@ struct gic_intrmask_regs {
  */
 struct gic_intr_map {
 	unsigned int cpunum;	/* Directed to this CPU */
+#define GIC_UNUSED		0xdead			/* Dummy data */
 	unsigned int pin;	/* Directed to this Pin */
 	unsigned int polarity;	/* Polarity : +/-	*/
 	unsigned int trigtype;	/* Trigger  : Edge/Levl */

arch/mips/include/asm/mach-tx49xx/kmalloc.h

@@ -1,6 +1,6 @@
 #ifndef __ASM_MACH_TX49XX_KMALLOC_H
 #define __ASM_MACH_TX49XX_KMALLOC_H
 
-#define ARCH_KMALLOC_MINALIGN	L1_CACHE_BYTES
+#define ARCH_DMA_MINALIGN L1_CACHE_BYTES
 
 #endif /* __ASM_MACH_TX49XX_KMALLOC_H */

arch/mips/include/asm/mips-boards/maltaint.h

@@ -88,9 +88,6 @@
 
 #define GIC_EXT_INTR(x)		x
 
-/* Dummy data */
-#define X			0xdead
-
 /* External Interrupts used for IPI */
 #define GIC_IPI_EXT_INTR_RESCHED_VPE0	16
 #define GIC_IPI_EXT_INTR_CALLFNC_VPE0	17

arch/mips/include/asm/page.h

@@ -150,6 +150,20 @@ typedef struct { unsigned long pgprot; } pgprot_t;
     ((unsigned long)(x) - PAGE_OFFSET + PHYS_OFFSET)
 #endif
 #define __va(x)		((void *)((unsigned long)(x) + PAGE_OFFSET - PHYS_OFFSET))
+
+/*
+ * RELOC_HIDE was originally added by 6007b903dfe5f1d13e0c711ac2894bdd4a61b1ad
+ * (lmo) rsp. 8431fd094d625b94d364fe393076ccef88e6ce18 (kernel.org).  The
+ * discussion can be found in lkml posting
+ * <a2ebde260608230500o3407b108hc03debb9da6e62c@mail.gmail.com> which is
+ * archived at http://lists.linuxcoding.com/kernel/2006-q3/msg17360.html
+ *
+ * It is unclear if the misscompilations mentioned in
+ * http://lkml.org/lkml/2010/8/8/138 also affect MIPS so we keep this one
+ * until GCC 3.x has been retired before we can apply
+ * https://patchwork.linux-mips.org/patch/1541/
+ */
+
 #define __pa_symbol(x)	__pa(RELOC_HIDE((unsigned long)(x), 0))
 
 #define pfn_to_kaddr(pfn)	__va((pfn) << PAGE_SHIFT)

arch/mips/include/asm/siginfo.h

@@ -88,6 +88,7 @@ typedef struct siginfo {
 #ifdef __ARCH_SI_TRAPNO
 			int _trapno;	/* TRAP # which caused the signal */
 #endif
+			short _addr_lsb;
 		} _sigfault;
 
 		/* SIGPOLL, SIGXFSZ (To do ...)  */

arch/mips/include/asm/thread_info.h

@@ -146,7 +146,8 @@ register struct thread_info *__current_thread_info __asm__("$28");
 #define _TIF_LOAD_WATCH		(1<<TIF_LOAD_WATCH)
 
 /* work to do on interrupt/exception return */
-#define _TIF_WORK_MASK		(0x0000ffef & ~_TIF_SECCOMP)
+#define _TIF_WORK_MASK		(0x0000ffef &				\
+					~(_TIF_SECCOMP | _TIF_SYSCALL_AUDIT))
 /* work to do on any return to u-space */
 #define _TIF_ALLWORK_MASK	(0x8000ffff & ~_TIF_SECCOMP)
 

arch/mips/include/asm/unistd.h

@@ -356,16 +356,19 @@
 #define __NR_perf_event_open		(__NR_Linux + 333)
 #define __NR_accept4			(__NR_Linux + 334)
 #define __NR_recvmmsg			(__NR_Linux + 335)
+#define __NR_fanotify_init		(__NR_Linux + 336)
+#define __NR_fanotify_mark		(__NR_Linux + 337)
+#define __NR_prlimit64			(__NR_Linux + 338)
 
 /*
  * Offset of the last Linux o32 flavoured syscall
  */
-#define __NR_Linux_syscalls		335
+#define __NR_Linux_syscalls		338
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
 
 #define __NR_O32_Linux			4000
-#define __NR_O32_Linux_syscalls		335
+#define __NR_O32_Linux_syscalls		338
 
 #if _MIPS_SIM == _MIPS_SIM_ABI64
 
@@ -668,16 +671,19 @@
 #define __NR_perf_event_open		(__NR_Linux + 292)
 #define __NR_accept4			(__NR_Linux + 293)
 #define __NR_recvmmsg			(__NR_Linux + 294)
+#define __NR_fanotify_init		(__NR_Linux + 295)
+#define __NR_fanotify_mark		(__NR_Linux + 296)
+#define __NR_prlimit64			(__NR_Linux + 297)
 
 /*
  * Offset of the last Linux 64-bit flavoured syscall
  */
-#define __NR_Linux_syscalls		294
+#define __NR_Linux_syscalls		297
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
 
 #define __NR_64_Linux			5000
-#define __NR_64_Linux_syscalls		294
+#define __NR_64_Linux_syscalls		297
 
 #if _MIPS_SIM == _MIPS_SIM_NABI32
 
@@ -985,16 +991,19 @@
 #define __NR_accept4			(__NR_Linux + 297)
 #define __NR_recvmmsg			(__NR_Linux + 298)
 #define __NR_getdents64			(__NR_Linux + 299)
+#define __NR_fanotify_init		(__NR_Linux + 300)
+#define __NR_fanotify_mark		(__NR_Linux + 301)
+#define __NR_prlimit64			(__NR_Linux + 302)
 
 /*
  * Offset of the last N32 flavoured syscall
  */
-#define __NR_Linux_syscalls		299
+#define __NR_Linux_syscalls		302
 
 #endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */
 
 #define __NR_N32_Linux			6000
-#define __NR_N32_Linux_syscalls		299
+#define __NR_N32_Linux_syscalls		302
 
 #ifdef __KERNEL__
 

arch/mips/kernel/irq-gic.c

@@ -7,7 +7,6 @@
 #include <asm/io.h>
 #include <asm/gic.h>
 #include <asm/gcmpregs.h>
-#include <asm/mips-boards/maltaint.h>
 #include <asm/irq.h>
 #include <linux/hardirq.h>
 #include <asm-generic/bitops/find.h>
@@ -131,7 +130,7 @@ static int gic_set_affinity(unsigned int irq, const struct cpumask *cpumask)
 	int		i;
 
 	irq -= _irqbase;
-	pr_debug(KERN_DEBUG "%s(%d) called\n", __func__, irq);
+	pr_debug("%s(%d) called\n", __func__, irq);
 	cpumask_and(&tmp, cpumask, cpu_online_mask);
 	if (cpus_empty(tmp))
 		return -1;
@@ -222,7 +221,7 @@ static void __init gic_basic_init(int numintrs, int numvpes,
 	/* Setup specifics */
 	for (i = 0; i < mapsize; i++) {
 		cpu = intrmap[i].cpunum;
-		if (cpu == X)
+		if (cpu == GIC_UNUSED)
 			continue;
 		if (cpu == 0 && i != 0 && intrmap[i].flags == 0)
 			continue;

arch/mips/kernel/kgdb.c

@@ -283,7 +283,7 @@ static int kgdb_mips_notify(struct notifier_block *self, unsigned long cmd,
 	struct pt_regs *regs = args->regs;
 	int trap = (regs->cp0_cause & 0x7c) >> 2;
 
-	/* Userpace events, ignore. */
+	/* Userspace events, ignore. */
 	if (user_mode(regs))
 		return NOTIFY_DONE;
 

arch/mips/kernel/kspd.c

@@ -251,7 +251,7 @@ void sp_work_handle_request(void)
  		memset(&tz, 0, sizeof(tz));
  		if ((ret.retval = sp_syscall(__NR_gettimeofday, (int)&tv,
 					     (int)&tz, 0, 0)) == 0)
-		ret.retval = tv.tv_sec;
+			ret.retval = tv.tv_sec;
 		break;
 
  	case MTSP_SYSCALL_EXIT:

arch/mips/kernel/linux32.c

@@ -341,3 +341,10 @@ asmlinkage long sys32_lookup_dcookie(u32 a0, u32 a1, char __user *buf,
 {
 	return sys_lookup_dcookie(merge_64(a0, a1), buf, len);
 }
+
+SYSCALL_DEFINE6(32_fanotify_mark, int, fanotify_fd, unsigned int, flags,
+		u64, a3, u64, a4, int, dfd, const char  __user *, pathname)
+{
+	return sys_fanotify_mark(fanotify_fd, flags, merge_64(a3, a4),
+				 dfd, pathname);
+}

arch/mips/kernel/scall32-o32.S

@@ -583,7 +583,10 @@ einval:	li	v0, -ENOSYS
 	sys	sys_rt_tgsigqueueinfo	4
 	sys	sys_perf_event_open	5
 	sys	sys_accept4		4
-	sys     sys_recvmmsg            5
+	sys	sys_recvmmsg		5	/* 4335 */
+	sys	sys_fanotify_init	2
+	sys	sys_fanotify_mark	6
+	sys	sys_prlimit64		4
 	.endm
 
 	/* We pre-compute the number of _instruction_ bytes needed to

arch/mips/kernel/scall64-64.S

@@ -416,9 +416,12 @@ sys_call_table:
 	PTR	sys_pipe2
 	PTR	sys_inotify_init1
 	PTR	sys_preadv
-	PTR	sys_pwritev			/* 5390 */
+	PTR	sys_pwritev			/* 5290 */
 	PTR	sys_rt_tgsigqueueinfo
 	PTR	sys_perf_event_open
 	PTR	sys_accept4
-	PTR     sys_recvmmsg
+	PTR	sys_recvmmsg
+	PTR	sys_fanotify_init		/* 5295 */
+	PTR	sys_fanotify_mark
+	PTR	sys_prlimit64
 	.size	sys_call_table,.-sys_call_table

arch/mips/kernel/scall64-n32.S

@@ -419,5 +419,8 @@ EXPORT(sysn32_call_table)
 	PTR	sys_perf_event_open
 	PTR	sys_accept4
 	PTR     compat_sys_recvmmsg
-	PTR     sys_getdents
+	PTR     sys_getdents64
+	PTR	sys_fanotify_init		/* 6300 */
+	PTR	sys_fanotify_mark
+	PTR	sys_prlimit64
 	.size	sysn32_call_table,.-sysn32_call_table

arch/mips/kernel/scall64-o32.S

@@ -538,5 +538,8 @@ sys_call_table:
 	PTR	compat_sys_rt_tgsigqueueinfo
 	PTR	sys_perf_event_open
 	PTR	sys_accept4
-	PTR     compat_sys_recvmmsg
+	PTR	compat_sys_recvmmsg		/* 4335 */
+	PTR	sys_fanotify_init
+	PTR	sys_32_fanotify_mark
+	PTR	sys_prlimit64
 	.size	sys_call_table,.-sys_call_table

arch/mips/mm/dma-default.c

@@ -44,27 +44,39 @@ static inline int cpu_is_noncoherent_r10000(struct device *dev)
 
 static gfp_t massage_gfp_flags(const struct device *dev, gfp_t gfp)
 {
+	gfp_t dma_flag;
+
 	/* ignore region specifiers */
 	gfp &= ~(__GFP_DMA | __GFP_DMA32 | __GFP_HIGHMEM);
 
-#ifdef CONFIG_ZONE_DMA
+#ifdef CONFIG_ISA
 	if (dev == NULL)
-		gfp |= __GFP_DMA;
-	else if (dev->coherent_dma_mask < DMA_BIT_MASK(24))
-		gfp |= __GFP_DMA;
+		dma_flag = __GFP_DMA;
 	else
 #endif
-#ifdef CONFIG_ZONE_DMA32
+#if defined(CONFIG_ZONE_DMA32) && defined(CONFIG_ZONE_DMA)
 	     if (dev->coherent_dma_mask < DMA_BIT_MASK(32))
-		gfp |= __GFP_DMA32;
+			dma_flag = __GFP_DMA;
+	else if (dev->coherent_dma_mask < DMA_BIT_MASK(64))
+			dma_flag = __GFP_DMA32;
+	else
+#endif
+#if defined(CONFIG_ZONE_DMA32) && !defined(CONFIG_ZONE_DMA)
+	     if (dev->coherent_dma_mask < DMA_BIT_MASK(64))
+		dma_flag = __GFP_DMA32;
+	else
+#endif
+#if defined(CONFIG_ZONE_DMA) && !defined(CONFIG_ZONE_DMA32)
+	     if (dev->coherent_dma_mask < DMA_BIT_MASK(64))
+		dma_flag = __GFP_DMA;
 	else
 #endif
-		;
+		dma_flag = 0;
 
 	/* Don't invoke OOM killer */
 	gfp |= __GFP_NORETRY;
 
-	return gfp;
+	return gfp | dma_flag;
 }
 
 void *dma_alloc_noncoherent(struct device *dev, size_t size,

arch/mips/mm/sc-rm7k.c

@@ -30,7 +30,7 @@
 #define tc_lsize	32
 
 extern unsigned long icache_way_size, dcache_way_size;
-unsigned long tcache_size;
+static unsigned long tcache_size;
 
 #include <asm/r4kcache.h>
 

arch/mips/mti-malta/malta-int.c

@@ -385,6 +385,8 @@ static int __initdata msc_nr_eicirqs = ARRAY_SIZE(msc_eicirqmap);
  */
 
 #define GIC_CPU_NMI GIC_MAP_TO_NMI_MSK
+#define X GIC_UNUSED
+
 static struct gic_intr_map gic_intr_map[GIC_NUM_INTRS] = {
 	{ X, X,		   X,		X,		0 },
 	{ X, X,		   X,	 	X,		0 },
@@ -404,6 +406,7 @@ static struct gic_intr_map gic_intr_map[GIC_NUM_INTRS] = {
 	{ X, X,		   X,		X,	        0 },
 	/* The remainder of this table is initialised by fill_ipi_map */
 };
+#undef X
 
 /*
  * GCMP needs to be detected before any SMP initialisation

arch/mips/pci/pci-rc32434.c

@@ -118,7 +118,7 @@ static int __init rc32434_pcibridge_init(void)
 	if (!((pcicvalue == PCIM_H_EA) ||
 	      (pcicvalue == PCIM_H_IA_FIX) ||
 	      (pcicvalue == PCIM_H_IA_RR))) {
-		pr_err(KERN_ERR "PCI init error!!!\n");
+		pr_err("PCI init error!!!\n");
 		/* Not in Host Mode, return ERROR */
 		return -1;
 	}

arch/mips/pnx8550/common/reset.c

@@ -22,29 +22,19 @@
  */
 #include <linux/kernel.h>
 
+#include <asm/processor.h>
 #include <asm/reboot.h>
 #include <glb.h>
 
 void pnx8550_machine_restart(char *command)
 {
-	char head[] = "************* Machine restart *************";
-	char foot[] = "*******************************************";
-
-	printk("\n\n");
-	printk("%s\n", head);
-	if (command != NULL)
-		printk("* %s\n", command);
-	printk("%s\n", foot);
-
 	PNX8550_RST_CTL = PNX8550_RST_DO_SW_RST;
 }
 
 void pnx8550_machine_halt(void)
 {
-	printk("*** Machine halt. (Not implemented) ***\n");
-}
-
-void pnx8550_machine_power_off(void)
-{
-	printk("*** Machine power off.  (Not implemented) ***\n");
+	while (1) {
+		if (cpu_wait)
+			cpu_wait();
+	}
 }

arch/mips/pnx8550/common/setup.c

@@ -44,7 +44,6 @@
 extern void __init board_setup(void);
 extern void pnx8550_machine_restart(char *);
 extern void pnx8550_machine_halt(void);
-extern void pnx8550_machine_power_off(void);
 extern struct resource ioport_resource;
 extern struct resource iomem_resource;
 extern char *prom_getcmdline(void);
@@ -100,7 +99,7 @@ void __init plat_mem_setup(void)
 
         _machine_restart = pnx8550_machine_restart;
         _machine_halt = pnx8550_machine_halt;
-        pm_power_off = pnx8550_machine_power_off;
+        pm_power_off = pnx8550_machine_halt;
 
 	/* Clear the Global 2 Register, PCI Inta Output Enable Registers
 	   Bit 1:Enable DAC Powerdown

arch/mn10300/kernel/module.c

@@ -206,7 +206,7 @@ int module_finalize(const Elf_Ehdr *hdr,
 		    const Elf_Shdr *sechdrs,
 		    struct module *me)
 {
-	return module_bug_finalize(hdr, sechdrs, me);
+	return 0;
 }
 
 /*
@@ -214,5 +214,4 @@ int module_finalize(const Elf_Ehdr *hdr,
  */
 void module_arch_cleanup(struct module *mod)
 {
-	module_bug_cleanup(mod);
 }

arch/parisc/kernel/module.c

@@ -941,11 +941,10 @@ int module_finalize(const Elf_Ehdr *hdr,
 	nsyms = newptr - (Elf_Sym *)symhdr->sh_addr;
 	DEBUGP("NEW num_symtab %lu\n", nsyms);
 	symhdr->sh_size = nsyms * sizeof(Elf_Sym);
-	return module_bug_finalize(hdr, sechdrs, me);
+	return 0;
 }
 
 void module_arch_cleanup(struct module *mod)
 {
 	deregister_unwind_table(mod);
-	module_bug_cleanup(mod);
 }

arch/powerpc/kernel/module.c

@@ -63,11 +63,6 @@ int module_finalize(const Elf_Ehdr *hdr,
 		const Elf_Shdr *sechdrs, struct module *me)
 {
 	const Elf_Shdr *sect;
-	int err;
-
-	err = module_bug_finalize(hdr, sechdrs, me);
-	if (err)
-		return err;
 
 	/* Apply feature fixups */
 	sect = find_section(hdr, sechdrs, "__ftr_fixup");
@@ -101,5 +96,4 @@ int module_finalize(const Elf_Ehdr *hdr,
 
 void module_arch_cleanup(struct module *mod)
 {
-	module_bug_cleanup(mod);
 }

arch/s390/kernel/module.c

@@ -407,10 +407,9 @@ int module_finalize(const Elf_Ehdr *hdr,
 {
 	vfree(me->arch.syminfo);
 	me->arch.syminfo = NULL;
-	return module_bug_finalize(hdr, sechdrs, me);
+	return 0;
 }
 
 void module_arch_cleanup(struct module *mod)
 {
-	module_bug_cleanup(mod);
 }

arch/sh/kernel/module.c

@@ -149,13 +149,11 @@ int module_finalize(const Elf_Ehdr *hdr,
 	int ret = 0;
 
 	ret |= module_dwarf_finalize(hdr, sechdrs, me);
-	ret |= module_bug_finalize(hdr, sechdrs, me);
 
 	return ret;
 }
 
 void module_arch_cleanup(struct module *mod)
 {
-	module_bug_cleanup(mod);
 	module_dwarf_cleanup(mod);
 }

arch/um/drivers/hostaudio_kern.c

@@ -40,6 +40,11 @@ static char *mixer = HOSTAUDIO_DEV_MIXER;
 "    This is used to specify the host mixer device to the hostaudio driver.\n"\
 "    The default is \"" HOSTAUDIO_DEV_MIXER "\".\n\n"
 
+module_param(dsp, charp, 0644);
+MODULE_PARM_DESC(dsp, DSP_HELP);
+module_param(mixer, charp, 0644);
+MODULE_PARM_DESC(mixer, MIXER_HELP);
+
 #ifndef MODULE
 static int set_dsp(char *name, int *add)
 {
@@ -56,15 +61,6 @@ static int set_mixer(char *name, int *add)
 }
 
 __uml_setup("mixer=", set_mixer, "mixer=<mixer device>\n" MIXER_HELP);
-
-#else /*MODULE*/
-
-module_param(dsp, charp, 0644);
-MODULE_PARM_DESC(dsp, DSP_HELP);
-
-module_param(mixer, charp, 0644);
-MODULE_PARM_DESC(mixer, MIXER_HELP);
-
 #endif
 
 /* /dev/dsp file operations */

arch/um/drivers/ubd_kern.c

@@ -163,6 +163,7 @@ struct ubd {
 	struct scatterlist sg[MAX_SG];
 	struct request *request;
 	int start_sg, end_sg;
+	sector_t rq_pos;
 };
 
 #define DEFAULT_COW { \
@@ -187,6 +188,7 @@ struct ubd {
 	.request =		NULL, \
 	.start_sg =		0, \
 	.end_sg =		0, \
+	.rq_pos =		0, \
 }
 
 /* Protected by ubd_lock */
@@ -1228,7 +1230,6 @@ static void do_ubd_request(struct request_queue *q)
 {
 	struct io_thread_req *io_req;
 	struct request *req;
-	sector_t sector;
 	int n;
 
 	while(1){
@@ -1239,12 +1240,12 @@ static void do_ubd_request(struct request_queue *q)
 				return;
 
 			dev->request = req;
+			dev->rq_pos = blk_rq_pos(req);
 			dev->start_sg = 0;
 			dev->end_sg = blk_rq_map_sg(q, req, dev->sg);
 		}
 
 		req = dev->request;
-		sector = blk_rq_pos(req);
 		while(dev->start_sg < dev->end_sg){
 			struct scatterlist *sg = &dev->sg[dev->start_sg];
 
@@ -1256,10 +1257,9 @@ static void do_ubd_request(struct request_queue *q)
 				return;
 			}
 			prepare_request(req, io_req,
-					(unsigned long long)sector << 9,
+					(unsigned long long)dev->rq_pos << 9,
 					sg->offset, sg->length, sg_page(sg));
 
-			sector += sg->length >> 9;
 			n = os_write_file(thread_fd, &io_req,
 					  sizeof(struct io_thread_req *));
 			if(n != sizeof(struct io_thread_req *)){
@@ -1272,6 +1272,7 @@ static void do_ubd_request(struct request_queue *q)
 				return;
 			}
 
+			dev->rq_pos += sg->length >> 9;
 			dev->start_sg++;
 		}
 		dev->end_sg = 0;

arch/x86/ia32/ia32_aout.c

@@ -34,7 +34,7 @@
 #include <asm/ia32.h>
 
 #undef WARN_OLD
-#undef CORE_DUMP /* probably broken */
+#undef CORE_DUMP /* definitely broken */
 
 static int load_aout_binary(struct linux_binprm *, struct pt_regs *regs);
 static int load_aout_library(struct file *);
@@ -131,21 +131,15 @@ static void set_brk(unsigned long start, unsigned long end)
  * macros to write out all the necessary info.
  */
 
-static int dump_write(struct file *file, const void *addr, int nr)
-{
-	return file->f_op->write(file, addr, nr, &file->f_pos) == nr;
-}
+#include <linux/coredump.h>
 
 #define DUMP_WRITE(addr, nr)			     \
 	if (!dump_write(file, (void *)(addr), (nr))) \
 		goto end_coredump;
 
-#define DUMP_SEEK(offset)						\
-	if (file->f_op->llseek) {					\
-		if (file->f_op->llseek(file, (offset), 0) != (offset))	\
-			goto end_coredump;				\
-	} else								\
-		file->f_pos = (offset)
+#define DUMP_SEEK(offset)		\
+	if (!dump_seek(file, offset))	\
+		goto end_coredump;
 
 #define START_DATA()	(u.u_tsize << PAGE_SHIFT)
 #define START_STACK(u)	(u.start_stack)
@@ -217,12 +211,6 @@ static int aout_core_dump(long signr, struct pt_regs *regs, struct file *file,
 		dump_size = dump.u_ssize << PAGE_SHIFT;
 		DUMP_WRITE(dump_start, dump_size);
 	}
-	/*
-	 * Finally dump the task struct.  Not be used by gdb, but
-	 * could be useful
-	 */
-	set_fs(KERNEL_DS);
-	DUMP_WRITE(current, sizeof(*current));
 end_coredump:
 	set_fs(fs);
 	return has_dumped;

arch/x86/kernel/cpu/mcheck/mce_amd.c

@@ -141,6 +141,7 @@ void mce_amd_feature_init(struct cpuinfo_x86 *c)
 				address = (low & MASK_BLKPTR_LO) >> 21;
 				if (!address)
 					break;
+
 				address += MCG_XBLK_ADDR;
 			} else
 				++address;
@@ -148,12 +149,8 @@ void mce_amd_feature_init(struct cpuinfo_x86 *c)
 			if (rdmsr_safe(address, &low, &high))
 				break;
 
-			if (!(high & MASK_VALID_HI)) {
-				if (block)
-					continue;
-				else
-					break;
-			}
+			if (!(high & MASK_VALID_HI))
+				continue;
 
 			if (!(high & MASK_CNTP_HI)  ||
 			     (high & MASK_LOCKED_HI))

arch/x86/kernel/cpu/mcheck/therm_throt.c

@@ -216,7 +216,7 @@ static __cpuinit int thermal_throttle_add_dev(struct sys_device *sys_dev,
 		err = sysfs_add_file_to_group(&sys_dev->kobj,
 					      &attr_core_power_limit_count.attr,
 					      thermal_attr_group.name);
-	if (cpu_has(c, X86_FEATURE_PTS))
+	if (cpu_has(c, X86_FEATURE_PTS)) {
 		err = sysfs_add_file_to_group(&sys_dev->kobj,
 					      &attr_package_throttle_count.attr,
 					      thermal_attr_group.name);
@@ -224,6 +224,7 @@ static __cpuinit int thermal_throttle_add_dev(struct sys_device *sys_dev,
 			err = sysfs_add_file_to_group(&sys_dev->kobj,
 					&attr_package_power_limit_count.attr,
 					thermal_attr_group.name);
+	}
 
 	return err;
 }

arch/x86/kernel/cpu/perf_event_p4.c

@@ -660,8 +660,12 @@ static int p4_pmu_handle_irq(struct pt_regs *regs)
 	for (idx = 0; idx < x86_pmu.num_counters; idx++) {
 		int overflow;
 
-		if (!test_bit(idx, cpuc->active_mask))
+		if (!test_bit(idx, cpuc->active_mask)) {
+			/* catch in-flight IRQs */
+			if (__test_and_clear_bit(idx, cpuc->running))
+				handled++;
 			continue;
+		}
 
 		event = cpuc->events[idx];
 		hwc = &event->hw;

arch/x86/kernel/module.c

@@ -239,11 +239,10 @@ int module_finalize(const Elf_Ehdr *hdr,
 		apply_paravirt(pseg, pseg + para->sh_size);
 	}
 
-	return module_bug_finalize(hdr, sechdrs, me);
+	return 0;
 }
 
 void module_arch_cleanup(struct module *mod)
 {
 	alternatives_smp_module_del(mod);
-	module_bug_cleanup(mod);
 }

arch/x86/kvm/svm.c

@@ -766,7 +766,6 @@ static void init_vmcb(struct vcpu_svm *svm)
 
 	control->iopm_base_pa = iopm_base;
 	control->msrpm_base_pa = __pa(svm->msrpm);
-	control->tsc_offset = 0;
 	control->int_ctl = V_INTR_MASKING_MASK;
 
 	init_seg(&save->es);
@@ -902,6 +901,7 @@ static struct kvm_vcpu *svm_create_vcpu(struct kvm *kvm, unsigned int id)
 	svm->vmcb_pa = page_to_pfn(page) << PAGE_SHIFT;
 	svm->asid_generation = 0;
 	init_vmcb(svm);
+	svm->vmcb->control.tsc_offset = 0-native_read_tsc();
 
 	err = fx_init(&svm->vcpu);
 	if (err)

arch/x86/mm/srat_64.c

@@ -420,9 +420,11 @@ int __init acpi_scan_nodes(unsigned long start, unsigned long end)
 		return -1;
 	}
 
-	for_each_node_mask(i, nodes_parsed)
-		e820_register_active_regions(i, nodes[i].start >> PAGE_SHIFT,
-						nodes[i].end >> PAGE_SHIFT);
+	for (i = 0; i < num_node_memblks; i++)
+		e820_register_active_regions(memblk_nodeid[i],
+				node_memblk_range[i].start >> PAGE_SHIFT,
+				node_memblk_range[i].end >> PAGE_SHIFT);
+
 	/* for out of order entries in SRAT */
 	sort_node_map();
 	if (!nodes_cover_memory(nodes)) {

arch/x86/oprofile/nmi_int.c

@@ -674,6 +674,7 @@ static int __init ppro_init(char **cpu_type)
 	case 0x0f:
 	case 0x16:
 	case 0x17:
+	case 0x1d:
 		*cpu_type = "i386/core_2";
 		break;
 	case 0x1a:

arch/x86/xen/time.c

@@ -489,8 +489,9 @@ static void xen_hvm_setup_cpu_clockevents(void)
 __init void xen_hvm_init_time_ops(void)
 {
 	/* vector callback is needed otherwise we cannot receive interrupts
-	 * on cpu > 0 */
-	if (!xen_have_vector_callback && num_present_cpus() > 1)
+	 * on cpu > 0 and at this point we don't know how many cpus are
+	 * available */
+	if (!xen_have_vector_callback)
 		return;
 	if (!xen_feature(XENFEAT_hvm_safe_pvclock)) {
 		printk(KERN_INFO "Xen doesn't support pvclock on HVM,"

block/elevator.c

@@ -938,6 +938,7 @@ int elv_register_queue(struct request_queue *q)
 			}
 		}
 		kobject_uevent(&e->kobj, KOBJ_ADD);
+		e->registered = 1;
 	}
 	return error;
 }
@@ -947,6 +948,7 @@ static void __elv_unregister_queue(struct elevator_queue *e)
 {
 	kobject_uevent(&e->kobj, KOBJ_REMOVE);
 	kobject_del(&e->kobj);
+	e->registered = 0;
 }
 
 void elv_unregister_queue(struct request_queue *q)
@@ -1042,11 +1044,13 @@ static int elevator_switch(struct request_queue *q, struct elevator_type *new_e)
 
 	spin_unlock_irq(q->queue_lock);
 
-	__elv_unregister_queue(old_elevator);
+	if (old_elevator->registered) {
+		__elv_unregister_queue(old_elevator);
 
-	err = elv_register_queue(q);
-	if (err)
-		goto fail_register;
+		err = elv_register_queue(q);
+		if (err)
+			goto fail_register;
+	}
 
 	/*
 	 * finally exit old elevator and turn off BYPASS.

drivers/acpi/blacklist.c

@@ -204,6 +204,23 @@ static struct dmi_system_id acpi_osi_dmi_table[] __initdata = {
 		},
 	},
 	{
+	/*
+	 * There have a NVIF method in MSI GX723 DSDT need call by Nvidia
+	 * driver (e.g. nouveau) when user press brightness hotkey.
+	 * Currently, nouveau driver didn't do the job and it causes there
+	 * have a infinite while loop in DSDT when user press hotkey.
+	 * We add MSI GX723's dmi information to this table for workaround
+	 * this issue.
+	 * Will remove MSI GX723 from the table after nouveau grows support.
+	 */
+	.callback = dmi_disable_osi_vista,
+	.ident = "MSI GX723",
+	.matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR, "Micro-Star International"),
+		     DMI_MATCH(DMI_PRODUCT_NAME, "GX723"),
+		},
+	},
+	{
 	.callback = dmi_disable_osi_vista,
 	.ident = "Sony VGN-NS10J_S",
 	.matches = {

drivers/acpi/processor_core.c

@@ -346,4 +346,5 @@ void __init acpi_early_processor_set_pdc(void)
 	acpi_walk_namespace(ACPI_TYPE_PROCESSOR, ACPI_ROOT_OBJECT,
 			    ACPI_UINT32_MAX,
 			    early_init_pdc, NULL, NULL, NULL);
+	acpi_get_devices("ACPI0007", early_init_pdc, NULL, NULL);
 }

drivers/atm/iphase.c

@@ -3156,7 +3156,6 @@ static int __devinit ia_init_one(struct pci_dev *pdev,
 {  
 	struct atm_dev *dev;  
 	IADEV *iadev;  
-        unsigned long flags;
 	int ret;
 
 	iadev = kzalloc(sizeof(*iadev), GFP_KERNEL);
@@ -3188,19 +3187,14 @@ static int __devinit ia_init_one(struct pci_dev *pdev,
 	ia_dev[iadev_count] = iadev;
 	_ia_dev[iadev_count] = dev;
 	iadev_count++;
-	spin_lock_init(&iadev->misc_lock);
-	/* First fixes first. I don't want to think about this now. */
-	spin_lock_irqsave(&iadev->misc_lock, flags); 
 	if (ia_init(dev) || ia_start(dev)) {  
 		IF_INIT(printk("IA register failed!\n");)
 		iadev_count--;
 		ia_dev[iadev_count] = NULL;
 		_ia_dev[iadev_count] = NULL;
-		spin_unlock_irqrestore(&iadev->misc_lock, flags); 
 		ret = -EINVAL;
 		goto err_out_deregister_dev;
 	}
-	spin_unlock_irqrestore(&iadev->misc_lock, flags); 
 	IF_EVENT(printk("iadev_count = %d\n", iadev_count);)
 
 	iadev->next_board = ia_boards;  

drivers/atm/iphase.h

@@ -1022,7 +1022,7 @@ typedef struct iadev_t {
 	struct dle_q rx_dle_q;  
 	struct free_desc_q *rx_free_desc_qhead;  
 	struct sk_buff_head rx_dma_q;  
-        spinlock_t rx_lock, misc_lock;
+	spinlock_t rx_lock;
 	struct atm_vcc **rx_open;	/* list of all open VCs */  
         u16 num_rx_desc, rx_buf_sz, rxing;
         u32 rx_pkt_ram, rx_tmp_cnt;

drivers/atm/solos-pci.c

@@ -444,6 +444,7 @@ static ssize_t console_show(struct device *dev, struct device_attribute *attr,
 	struct atm_dev *atmdev = container_of(dev, struct atm_dev, class_dev);
 	struct solos_card *card = atmdev->dev_data;
 	struct sk_buff *skb;
+	unsigned int len;
 
 	spin_lock(&card->cli_queue_lock);
 	skb = skb_dequeue(&card->cli_queue[SOLOS_CHAN(atmdev)]);
@@ -451,11 +452,12 @@ static ssize_t console_show(struct device *dev, struct device_attribute *attr,
 	if(skb == NULL)
 		return sprintf(buf, "No data.\n");
 
-	memcpy(buf, skb->data, skb->len);
-	dev_dbg(&card->dev->dev, "len: %d\n", skb->len);
+	len = skb->len;
+	memcpy(buf, skb->data, len);
+	dev_dbg(&card->dev->dev, "len: %d\n", len);
 
 	kfree_skb(skb);
-	return skb->len;
+	return len;
 }
 
 static int send_command(struct solos_card *card, int dev, const char *buf, size_t size)

drivers/block/ps3disk.c

@@ -113,7 +113,7 @@ static void ps3disk_scatter_gather(struct ps3_storage_device *dev,
 			memcpy(buf, dev->bounce_buf+offset, size);
 		offset += size;
 		flush_kernel_dcache_page(bvec->bv_page);
-		bvec_kunmap_irq(bvec, &flags);
+		bvec_kunmap_irq(buf, &flags);
 		i++;
 	}
 }

drivers/block/virtio_blk.c

@@ -202,6 +202,7 @@ static int virtblk_get_id(struct gendisk *disk, char *id_str)
 	struct virtio_blk *vblk = disk->private_data;
 	struct request *req;
 	struct bio *bio;
+	int err;
 
 	bio = bio_map_kern(vblk->disk->queue, id_str, VIRTIO_BLK_ID_BYTES,
 			   GFP_KERNEL);
@@ -215,7 +216,10 @@ static int virtblk_get_id(struct gendisk *disk, char *id_str)
 	}
 
 	req->cmd_type = REQ_TYPE_SPECIAL;
-	return blk_execute_rq(vblk->disk->queue, vblk->disk, req, false);
+	err = blk_execute_rq(vblk->disk->queue, vblk->disk, req, false);
+	blk_put_request(req);
+
+	return err;
 }
 
 static int virtblk_locked_ioctl(struct block_device *bdev, fmode_t mode,

drivers/dma/ioat/dma_v2.c

@@ -879,7 +879,7 @@ int __devinit ioat2_dma_probe(struct ioatdma_device *device, int dca)
 	dma->device_issue_pending = ioat2_issue_pending;
 	dma->device_alloc_chan_resources = ioat2_alloc_chan_resources;
 	dma->device_free_chan_resources = ioat2_free_chan_resources;
-	dma->device_tx_status = ioat_tx_status;
+	dma->device_tx_status = ioat_dma_tx_status;
 
 	err = ioat_probe(device);
 	if (err)

drivers/gpu/drm/i915/i915_dma.c

@@ -2231,6 +2231,9 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	dev_priv->mchdev_lock = &mchdev_lock;
 	spin_unlock(&mchdev_lock);
 
+	/* XXX Prevent module unload due to memory corruption bugs. */
+	__module_get(THIS_MODULE);
+
 	return 0;
 
 out_workqueue_free:

drivers/gpu/drm/i915/intel_fb.c

@@ -238,8 +238,8 @@ int intel_fbdev_destroy(struct drm_device *dev,
 
 	drm_framebuffer_cleanup(&ifb->base);
 	if (ifb->obj) {
-		drm_gem_object_handle_unreference(ifb->obj);
 		drm_gem_object_unreference(ifb->obj);
+		ifb->obj = NULL;
 	}
 
 	return 0;

drivers/gpu/drm/nouveau/nouveau_fbcon.c

@@ -352,7 +352,6 @@ nouveau_fbcon_destroy(struct drm_device *dev, struct nouveau_fbdev *nfbdev)
 
 	if (nouveau_fb->nvbo) {
 		nouveau_bo_unmap(nouveau_fb->nvbo);
-		drm_gem_object_handle_unreference_unlocked(nouveau_fb->nvbo->gem);
 		drm_gem_object_unreference_unlocked(nouveau_fb->nvbo->gem);
 		nouveau_fb->nvbo = NULL;
 	}

drivers/gpu/drm/nouveau/nouveau_notifier.c

@@ -79,7 +79,6 @@ nouveau_notifier_takedown_channel(struct nouveau_channel *chan)
 	mutex_lock(&dev->struct_mutex);
 	nouveau_bo_unpin(chan->notifier_bo);
 	mutex_unlock(&dev->struct_mutex);
-	drm_gem_object_handle_unreference_unlocked(chan->notifier_bo->gem);
 	drm_gem_object_unreference_unlocked(chan->notifier_bo->gem);
 	drm_mm_takedown(&chan->notifier_heap);
 }

drivers/gpu/drm/radeon/evergreen.c

@@ -1137,7 +1137,7 @@ static void evergreen_gpu_init(struct radeon_device *rdev)
 
 		WREG32(RCU_IND_INDEX, 0x203);
 		efuse_straps_3 = RREG32(RCU_IND_DATA);
-		efuse_box_bit_127_124 = (u8)(efuse_straps_3 & 0xF0000000) >> 28;
+		efuse_box_bit_127_124 = (u8)((efuse_straps_3 & 0xF0000000) >> 28);
 
 		switch(efuse_box_bit_127_124) {
 		case 0x0:
@@ -1407,6 +1407,7 @@ int evergreen_mc_init(struct radeon_device *rdev)
 	rdev->mc.mc_vram_size = RREG32(CONFIG_MEMSIZE) * 1024 * 1024;
 	rdev->mc.real_vram_size = RREG32(CONFIG_MEMSIZE) * 1024 * 1024;
 	rdev->mc.visible_vram_size = rdev->mc.aper_size;
+	rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
 	r600_vram_gtt_location(rdev, &rdev->mc);
 	radeon_update_bandwidth_info(rdev);
 
@@ -1520,7 +1521,7 @@ void evergreen_disable_interrupt_state(struct radeon_device *rdev)
 {
 	u32 tmp;
 
-	WREG32(CP_INT_CNTL, 0);
+	WREG32(CP_INT_CNTL, CNTX_BUSY_INT_ENABLE | CNTX_EMPTY_INT_ENABLE);
 	WREG32(GRBM_INT_CNTL, 0);
 	WREG32(INT_MASK + EVERGREEN_CRTC0_REGISTER_OFFSET, 0);
 	WREG32(INT_MASK + EVERGREEN_CRTC1_REGISTER_OFFSET, 0);

drivers/gpu/drm/radeon/r100.c

@@ -1030,6 +1030,7 @@ int r100_cp_init(struct radeon_device *rdev, unsigned ring_size)
 		return r;
 	}
 	rdev->cp.ready = true;
+	rdev->mc.active_vram_size = rdev->mc.real_vram_size;
 	return 0;
 }
 
@@ -1047,6 +1048,7 @@ void r100_cp_fini(struct radeon_device *rdev)
 void r100_cp_disable(struct radeon_device *rdev)
 {
 	/* Disable ring */
+	rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
 	rdev->cp.ready = false;
 	WREG32(RADEON_CP_CSQ_MODE, 0);
 	WREG32(RADEON_CP_CSQ_CNTL, 0);
@@ -2295,6 +2297,7 @@ void r100_vram_init_sizes(struct radeon_device *rdev)
 	/* FIXME we don't use the second aperture yet when we could use it */
 	if (rdev->mc.visible_vram_size > rdev->mc.aper_size)
 		rdev->mc.visible_vram_size = rdev->mc.aper_size;
+	rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
 	config_aper_size = RREG32(RADEON_CONFIG_APER_SIZE);
 	if (rdev->flags & RADEON_IS_IGP) {
 		uint32_t tom;

drivers/gpu/drm/radeon/r600.c

@@ -1248,6 +1248,7 @@ int r600_mc_init(struct radeon_device *rdev)
 	rdev->mc.mc_vram_size = RREG32(CONFIG_MEMSIZE);
 	rdev->mc.real_vram_size = RREG32(CONFIG_MEMSIZE);
 	rdev->mc.visible_vram_size = rdev->mc.aper_size;
+	rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
 	r600_vram_gtt_location(rdev, &rdev->mc);
 
 	if (rdev->flags & RADEON_IS_IGP) {
@@ -1917,6 +1918,7 @@ void r600_pciep_wreg(struct radeon_device *rdev, u32 reg, u32 v)
  */
 void r600_cp_stop(struct radeon_device *rdev)
 {
+	rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
 	WREG32(R_0086D8_CP_ME_CNTL, S_0086D8_CP_ME_HALT(1));
 }
 
@@ -2910,7 +2912,7 @@ static void r600_disable_interrupt_state(struct radeon_device *rdev)
 {
 	u32 tmp;
 
-	WREG32(CP_INT_CNTL, 0);
+	WREG32(CP_INT_CNTL, CNTX_BUSY_INT_ENABLE | CNTX_EMPTY_INT_ENABLE);
 	WREG32(GRBM_INT_CNTL, 0);
 	WREG32(DxMODE_INT_MASK, 0);
 	if (ASIC_IS_DCE3(rdev)) {

drivers/gpu/drm/radeon/r600_blit_kms.c

@@ -532,6 +532,7 @@ int r600_blit_init(struct radeon_device *rdev)
 	memcpy(ptr + rdev->r600_blit.ps_offset, r6xx_ps, r6xx_ps_size * 4);
 	radeon_bo_kunmap(rdev->r600_blit.shader_obj);
 	radeon_bo_unreserve(rdev->r600_blit.shader_obj);
+	rdev->mc.active_vram_size = rdev->mc.real_vram_size;
 	return 0;
 }
 
@@ -539,6 +540,7 @@ void r600_blit_fini(struct radeon_device *rdev)
 {
 	int r;
 
+	rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
 	if (rdev->r600_blit.shader_obj == NULL)
 		return;
 	/* If we can't reserve the bo, unref should be enough to destroy

drivers/gpu/drm/radeon/radeon.h

@@ -344,6 +344,7 @@ struct radeon_mc {
 	 * about vram size near mc fb location */
 	u64			mc_vram_size;
 	u64			visible_vram_size;
+	u64			active_vram_size;
 	u64			gtt_size;
 	u64			gtt_start;
 	u64			gtt_end;

drivers/gpu/drm/radeon/radeon_atombios.c

@@ -1558,39 +1558,39 @@ radeon_atombios_get_tv_info(struct radeon_device *rdev)
 		switch (tv_info->ucTV_BootUpDefaultStandard) {
 		case ATOM_TV_NTSC:
 			tv_std = TV_STD_NTSC;
-			DRM_INFO("Default TV standard: NTSC\n");
+			DRM_DEBUG_KMS("Default TV standard: NTSC\n");
 			break;
 		case ATOM_TV_NTSCJ:
 			tv_std = TV_STD_NTSC_J;
-			DRM_INFO("Default TV standard: NTSC-J\n");
+			DRM_DEBUG_KMS("Default TV standard: NTSC-J\n");
 			break;
 		case ATOM_TV_PAL:
 			tv_std = TV_STD_PAL;
-			DRM_INFO("Default TV standard: PAL\n");
+			DRM_DEBUG_KMS("Default TV standard: PAL\n");
 			break;
 		case ATOM_TV_PALM:
 			tv_std = TV_STD_PAL_M;
-			DRM_INFO("Default TV standard: PAL-M\n");
+			DRM_DEBUG_KMS("Default TV standard: PAL-M\n");
 			break;
 		case ATOM_TV_PALN:
 			tv_std = TV_STD_PAL_N;
-			DRM_INFO("Default TV standard: PAL-N\n");
+			DRM_DEBUG_KMS("Default TV standard: PAL-N\n");
 			break;
 		case ATOM_TV_PALCN:
 			tv_std = TV_STD_PAL_CN;
-			DRM_INFO("Default TV standard: PAL-CN\n");
+			DRM_DEBUG_KMS("Default TV standard: PAL-CN\n");
 			break;
 		case ATOM_TV_PAL60:
 			tv_std = TV_STD_PAL_60;
-			DRM_INFO("Default TV standard: PAL-60\n");
+			DRM_DEBUG_KMS("Default TV standard: PAL-60\n");
 			break;
 		case ATOM_TV_SECAM:
 			tv_std = TV_STD_SECAM;
-			DRM_INFO("Default TV standard: SECAM\n");
+			DRM_DEBUG_KMS("Default TV standard: SECAM\n");
 			break;
 		default:
 			tv_std = TV_STD_NTSC;
-			DRM_INFO("Unknown TV standard; defaulting to NTSC\n");
+			DRM_DEBUG_KMS("Unknown TV standard; defaulting to NTSC\n");
 			break;
 		}
 	}

drivers/gpu/drm/radeon/radeon_combios.c

@@ -913,47 +913,47 @@ radeon_combios_get_tv_info(struct radeon_device *rdev)
 			switch (RBIOS8(tv_info + 7) & 0xf) {
 			case 1:
 				tv_std = TV_STD_NTSC;
-				DRM_INFO("Default TV standard: NTSC\n");
+				DRM_DEBUG_KMS("Default TV standard: NTSC\n");
 				break;
 			case 2:
 				tv_std = TV_STD_PAL;
-				DRM_INFO("Default TV standard: PAL\n");
+				DRM_DEBUG_KMS("Default TV standard: PAL\n");
 				break;
 			case 3:
 				tv_std = TV_STD_PAL_M;
-				DRM_INFO("Default TV standard: PAL-M\n");
+				DRM_DEBUG_KMS("Default TV standard: PAL-M\n");
 				break;
 			case 4:
 				tv_std = TV_STD_PAL_60;
-				DRM_INFO("Default TV standard: PAL-60\n");
+				DRM_DEBUG_KMS("Default TV standard: PAL-60\n");
 				break;
 			case 5:
 				tv_std = TV_STD_NTSC_J;
-				DRM_INFO("Default TV standard: NTSC-J\n");
+				DRM_DEBUG_KMS("Default TV standard: NTSC-J\n");
 				break;
 			case 6:
 				tv_std = TV_STD_SCART_PAL;
-				DRM_INFO("Default TV standard: SCART-PAL\n");
+				DRM_DEBUG_KMS("Default TV standard: SCART-PAL\n");
 				break;
 			default:
 				tv_std = TV_STD_NTSC;
-				DRM_INFO
+				DRM_DEBUG_KMS
 				    ("Unknown TV standard; defaulting to NTSC\n");
 				break;
 			}
 
 			switch ((RBIOS8(tv_info + 9) >> 2) & 0x3) {
 			case 0:
-				DRM_INFO("29.498928713 MHz TV ref clk\n");
+				DRM_DEBUG_KMS("29.498928713 MHz TV ref clk\n");
 				break;
 			case 1:
-				DRM_INFO("28.636360000 MHz TV ref clk\n");
+				DRM_DEBUG_KMS("28.636360000 MHz TV ref clk\n");
 				break;
 			case 2:
-				DRM_INFO("14.318180000 MHz TV ref clk\n");
+				DRM_DEBUG_KMS("14.318180000 MHz TV ref clk\n");
 				break;
 			case 3:
-				DRM_INFO("27.000000000 MHz TV ref clk\n");
+				DRM_DEBUG_KMS("27.000000000 MHz TV ref clk\n");
 				break;
 			default:
 				break;
@@ -1324,7 +1324,7 @@ bool radeon_legacy_get_tmds_info_from_combios(struct radeon_encoder *encoder,
 
 	if (tmds_info) {
 		ver = RBIOS8(tmds_info);
-		DRM_INFO("DFP table revision: %d\n", ver);
+		DRM_DEBUG_KMS("DFP table revision: %d\n", ver);
 		if (ver == 3) {
 			n = RBIOS8(tmds_info + 5) + 1;
 			if (n > 4)
@@ -1408,7 +1408,7 @@ bool radeon_legacy_get_ext_tmds_info_from_combios(struct radeon_encoder *encoder
 		offset = combios_get_table_offset(dev, COMBIOS_EXT_TMDS_INFO_TABLE);
 		if (offset) {
 			ver = RBIOS8(offset);
-			DRM_INFO("External TMDS Table revision: %d\n", ver);
+			DRM_DEBUG_KMS("External TMDS Table revision: %d\n", ver);
 			tmds->slave_addr = RBIOS8(offset + 4 + 2);
 			tmds->slave_addr >>= 1; /* 7 bit addressing */
 			gpio = RBIOS8(offset + 4 + 3);

drivers/gpu/drm/radeon/radeon_fb.c

@@ -97,7 +97,6 @@ static void radeonfb_destroy_pinned_object(struct drm_gem_object *gobj)
 		radeon_bo_unpin(rbo);
 		radeon_bo_unreserve(rbo);
 	}
-	drm_gem_object_handle_unreference(gobj);
 	drm_gem_object_unreference_unlocked(gobj);
 }
 

drivers/gpu/drm/radeon/radeon_object.c

@@ -69,7 +69,7 @@ void radeon_ttm_placement_from_domain(struct radeon_bo *rbo, u32 domain)
 	u32 c = 0;
 
 	rbo->placement.fpfn = 0;
-	rbo->placement.lpfn = 0;
+	rbo->placement.lpfn = rbo->rdev->mc.active_vram_size >> PAGE_SHIFT;
 	rbo->placement.placement = rbo->placements;
 	rbo->placement.busy_placement = rbo->placements;
 	if (domain & RADEON_GEM_DOMAIN_VRAM)

drivers/gpu/drm/radeon/radeon_object.h

@@ -124,11 +124,8 @@ static inline int radeon_bo_wait(struct radeon_bo *bo, u32 *mem_type,
 	int r;
 
 	r = ttm_bo_reserve(&bo->tbo, true, no_wait, false, 0);
-	if (unlikely(r != 0)) {
-		if (r != -ERESTARTSYS)
-			dev_err(bo->rdev->dev, "%p reserve failed for wait\n", bo);
+	if (unlikely(r != 0))
 		return r;
-	}
 	spin_lock(&bo->tbo.lock);
 	if (mem_type)
 		*mem_type = bo->tbo.mem.mem_type;

drivers/gpu/drm/radeon/rs600.c

@@ -693,6 +693,7 @@ void rs600_mc_init(struct radeon_device *rdev)
 	rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
 	rdev->mc.mc_vram_size = rdev->mc.real_vram_size;
 	rdev->mc.visible_vram_size = rdev->mc.aper_size;
+	rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
 	rdev->mc.igp_sideport_enabled = radeon_atombios_sideport_present(rdev);
 	base = RREG32_MC(R_000004_MC_FB_LOCATION);
 	base = G_000004_MC_FB_START(base) << 16;