Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/w1-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/w1-2.6:
  [PATCH] w1: warning fix
  [PATCH] w1: clean up W1_CON dependency.
  [PATCH] drivers/w1/w1.c: fix a compile error
  [PATCH] W1: fix dependencies of W1_SLAVE_DS2433_CRC
  [PATCH] W1: possible cleanups
  [PATCH] W1: cleanups
  [PATCH] w1 exports
  [PATCH] w1: Use mutexes instead of semaphores.
  [PATCH] w1: Make w1 connector notifications depend on connector.
  [PATCH] w1: netlink: Mark netlink group 1 as unused.
  [PATCH] w1: Move w1-connector definitions into linux/include/connector.h
  [PATCH] w1: Userspace communication protocol over connector.
  [PATCH] w1: Replace dscore and ds_w1_bridge with ds2490 driver.
  [PATCH] w1: Added default generic read/write operations.

Documentation/w1/masters/ds2490

@@ -0,0 +1,18 @@
+Kernel driver ds2490
+====================
+
+Supported chips:
+  * Maxim DS2490 based
+
+Author: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
+
+
+Description
+-----------
+
+The Maixm/Dallas Semiconductor DS2490 is a chip
+which allows to build USB <-> W1 bridges.
+
+DS9490(R) is a USB <-> W1 bus master device
+which has 0x81 family ID integrated chip and DS2490
+low-level operational chip.

Documentation/w1/w1.generic

@@ -27,8 +27,19 @@ When a w1 master driver registers with the w1 subsystem, the following occurs:
 
 When a device is found on the bus, w1 core checks if driver for it's family is
 loaded. If so, the family driver is attached to the slave.
-If there is no driver for the family, a simple sysfs entry is created
-for the slave device.
+If there is no driver for the family, default one is assigned, which allows to perform
+almost any kind of operations. Each logical operation is a transaction
+in nature, which can contain several (two or one) low-level operations.
+Let's see how one can read EEPROM context:
+1. one must write control buffer, i.e. buffer containing command byte
+and two byte address. At this step bus is reset and appropriate device
+is selected using either W1_SKIP_ROM or W1_MATCH_ROM command.
+Then provided control buffer is being written to the wire.
+2. reading. This will issue reading eeprom response.
+
+It is possible that between 1. and 2. w1 master thread will reset bus for searching
+and slave device will be even removed, but in this case 0xff will
+be read, since no device was selected.
 
 
 W1 device families
@@ -89,4 +100,5 @@ driver             - (standard) symlink to the w1 driver
 name               - the device name, usually the same as the directory name
 w1_slave           - (optional) a binary file whose meaning depends on the
                      family driver
-
+rw		   - (optional) created for slave devices which do not have
+		     appropriate family driver. Allows to read/write binary data.

Documentation/w1/w1.netlink

@@ -0,0 +1,98 @@
+Userspace communication protocol over connector [1].
+
+
+Message types.
+=============
+
+There are three types of messages between w1 core and userspace:
+1. Events. They are generated each time new master or slave device found
+	either due to automatic or requested search.
+2. Userspace commands. Includes read/write and search/alarm search comamnds.
+3. Replies to userspace commands.
+
+
+Protocol.
+========
+
+[struct cn_msg] - connector header. It's length field is equal to size of the attached data.
+[struct w1_netlink_msg] - w1 netlink header.
+	__u8 type 	- message type.
+			W1_SLAVE_ADD/W1_SLAVE_REMOVE - slave add/remove events.
+			W1_MASTER_ADD/W1_MASTER_REMOVE - master add/remove events.
+			W1_MASTER_CMD - userspace command for bus master device (search/alarm search).
+			W1_SLAVE_CMD - userspace command for slave device (read/write/ search/alarm search
+					for bus master device where given slave device found).
+	__u8 res	- reserved
+	__u16 len	- size of attached to this header data.
+	union {
+		__u8 id;			 - slave unique device id
+		struct w1_mst {
+			__u32		id;	 - master's id.
+			__u32		res;	 - reserved
+		} mst;
+	} id;
+
+[strucrt w1_netlink_cmd] - command for gived master or slave device.
+	__u8 cmd	- command opcode.
+			W1_CMD_READ 	- read command.
+			W1_CMD_WRITE	- write command.
+			W1_CMD_SEARCH	- search command.
+			W1_CMD_ALARM_SEARCH - alarm search command.
+	__u8 res	- reserved
+	__u16 len	- length of data for this command.
+			For read command data must be allocated like for write command.
+	__u8 data[0]	- data for this command.
+
+
+Each connector message can include one or more w1_netlink_msg with zero of more attached w1_netlink_cmd messages.
+
+For event messages there are no w1_netlink_cmd embedded structures, only connector header
+and w1_netlink_msg strucutre with "len" field being zero and filled type (one of event types)
+and id - either 8 bytes of slave unique id in host order, or master's id, which is assigned
+to bus master device when it is added to w1 core.
+
+Currently replies to userspace commands are only generated for read command request.
+One reply is generated exactly for one w1_netlink_cmd read request.
+Replies are not combined when sent - i.e. typical reply messages looks like the following:
+[cn_msg][w1_netlink_msg][w1_netlink_cmd]
+cn_msg.len = sizeof(struct w1_netlink_msg) + sizeof(struct w1_netlink_cmd) + cmd->len;
+w1_netlink_msg.len = sizeof(struct w1_netlink_cmd) + cmd->len;
+w1_netlink_cmd.len = cmd->len;
+
+
+Operation steps in w1 core when new command is received.
+=======================================================
+
+When new message (w1_netlink_msg) is received w1 core detects if it is master of slave request,
+according to w1_netlink_msg.type field.
+Then master or slave device is searched for.
+When found, master device (requested or those one on where slave device is found) is locked.
+If slave command is requested, then reset/select procedure is started to select given device.
+
+Then all requested in w1_netlink_msg operations are performed one by one.
+If command requires reply (like read command) it is sent on command completion.
+
+When all commands (w1_netlink_cmd) are processed muster device is unlocked
+and next w1_netlink_msg header processing started.
+
+
+Connector [1] specific documentation.
+====================================
+
+Each connector message includes two u32 fields as "address".
+w1 uses CN_W1_IDX and CN_W1_VAL defined in include/linux/connector.h header.
+Each message also includes sequence and acknowledge numbers.
+Sequence number for event messages is appropriate bus master sequence number increased with
+each event message sent "through" this master.
+Sequence number for userspace requests is set by userspace application.
+Sequence number for reply is the same as was in request, and
+acknowledge number is set to seq+1.
+
+
+Additional documantion, source code examples.
+============================================
+
+1. Documentation/connector
+2. http://tservice.net.ru/~s0mbre/archive/w1
+This archive includes userspace application w1d.c which
+uses read/write/search commands for all master/slave devices found on the bus.

drivers/w1/Kconfig

@@ -3,7 +3,7 @@ menu "Dallas's 1-wire bus"
 config W1
 	tristate "Dallas's 1-wire support"
 	---help---
-	  Dallas's 1-wire bus is useful to connect slow 1-pin devices
+	  Dallas' 1-wire bus is useful to connect slow 1-pin devices
 	  such as iButtons and thermal sensors.
 
 	  If you want W1 support, you should say Y here.
@@ -11,6 +11,18 @@ config W1
 	  This W1 support can also be built as a module.  If so, the module
 	  will be called wire.ko.
 
+config W1_CON
+	depends on CONNECTOR && W1
+	bool "Userspace communication over connector"
+	default y
+	--- help ---
+	  This allows to communicate with userspace using connector [Documentation/connector].
+	  There are three types of messages between w1 core and userspace:
+	  1. Events. They are generated each time new master or slave device found
+		either due to automatic or requested search.
+	  2. Userspace commands. Includes read/write and search/alarm search comamnds.
+	  3. Replies to userspace commands.
+
 source drivers/w1/masters/Kconfig
 source drivers/w1/slaves/Kconfig
 

drivers/w1/Makefile

@@ -2,10 +2,6 @@
 # Makefile for the Dallas's 1-wire bus.
 #
 
-ifneq ($(CONFIG_NET), y)
-EXTRA_CFLAGS	+= -DNETLINK_DISABLED
-endif
-
 ifeq ($(CONFIG_W1_DS2433_CRC), y)
 EXTRA_CFLAGS	+= -DCONFIG_W1_F23_CRC
 endif

drivers/w1/masters/Kconfig

@@ -15,24 +15,15 @@ config W1_MASTER_MATROX
 	  This support is also available as a module.  If so, the module
 	  will be called matrox_w1.ko.
 
-config W1_MASTER_DS9490
-	tristate "DS9490R transport layer driver"
-	depends on W1 && USB
-	help
-	  Say Y here if you want to have a driver for DS9490R UWB <-> W1 bridge.
-
-	  This support is also available as a module.  If so, the module
-	  will be called ds9490r.ko.
-
-config W1_MASTER_DS9490_BRIDGE
-	tristate "DS9490R USB <-> W1 transport layer for 1-wire"
-	depends on W1_MASTER_DS9490
-	help
-	  Say Y here if you want to communicate with your 1-wire devices
-	  using DS9490R USB bridge.
-
-	  This support is also available as a module.  If so, the module
-	  will be called ds_w1_bridge.ko.
+config W1_MASTER_DS2490
+	tristate "DS2490 USB <-> W1 transport layer for 1-wire"
+  	depends on W1 && USB
+  	help
+	  Say Y here if you want to have a driver for DS2490 based USB <-> W1 bridges,
+	  for example DS9490*.
+
+  	  This support is also available as a module.  If so, the module
+	  will be called ds2490.ko.
 
 config W1_MASTER_DS2482
 	tristate "Maxim DS2482 I2C to 1-Wire bridge"

drivers/w1/masters/Makefile

@@ -3,11 +3,6 @@
 #
 
 obj-$(CONFIG_W1_MASTER_MATROX)		+= matrox_w1.o
-
-obj-$(CONFIG_W1_MASTER_DS9490)		+= ds9490r.o
-ds9490r-objs    := dscore.o
-
-obj-$(CONFIG_W1_MASTER_DS9490_BRIDGE)	+= ds_w1_bridge.o
-
+obj-$(CONFIG_W1_MASTER_DS2490)		+= ds2490.o
 obj-$(CONFIG_W1_MASTER_DS2482)		+= ds2482.o
 

drivers/w1/masters/ds2482.c

@@ -125,7 +125,7 @@ struct ds2482_w1_chan {
 
 struct ds2482_data {
 	struct i2c_client	client;
-	struct semaphore	access_lock;
+	struct mutex		access_lock;
 
 	/* 1-wire interface(s) */
 	int			w1_count;	/* 1 or 8 */
@@ -265,7 +265,7 @@ static u8 ds2482_w1_touch_bit(void *data, u8 bit)
 	struct ds2482_data    *pdev = pchan->pdev;
 	int status = -1;
 
-	down(&pdev->access_lock);
+	mutex_lock(&pdev->access_lock);
 
 	/* Select the channel */
 	ds2482_wait_1wire_idle(pdev);
@@ -277,7 +277,7 @@ static u8 ds2482_w1_touch_bit(void *data, u8 bit)
 				  bit ? 0xFF : 0))
 		status = ds2482_wait_1wire_idle(pdev);
 
-	up(&pdev->access_lock);
+	mutex_unlock(&pdev->access_lock);
 
 	return (status & DS2482_REG_STS_SBR) ? 1 : 0;
 }
@@ -297,7 +297,7 @@ static u8 ds2482_w1_triplet(void *data, u8 dbit)
 	struct ds2482_data    *pdev = pchan->pdev;
 	int status = (3 << 5);
 
-	down(&pdev->access_lock);
+	mutex_lock(&pdev->access_lock);
 
 	/* Select the channel */
 	ds2482_wait_1wire_idle(pdev);
@@ -309,7 +309,7 @@ static u8 ds2482_w1_triplet(void *data, u8 dbit)
 				  dbit ? 0xFF : 0))
 		status = ds2482_wait_1wire_idle(pdev);
 
-	up(&pdev->access_lock);
+	mutex_unlock(&pdev->access_lock);
 
 	/* Decode the status */
 	return (status >> 5);
@@ -326,7 +326,7 @@ static void ds2482_w1_write_byte(void *data, u8 byte)
 	struct ds2482_w1_chan *pchan = data;
 	struct ds2482_data    *pdev = pchan->pdev;
 
-	down(&pdev->access_lock);
+	mutex_lock(&pdev->access_lock);
 
 	/* Select the channel */
 	ds2482_wait_1wire_idle(pdev);
@@ -336,7 +336,7 @@ static void ds2482_w1_write_byte(void *data, u8 byte)
 	/* Send the write byte command */
 	ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_WRITE_BYTE, byte);
 
-	up(&pdev->access_lock);
+	mutex_unlock(&pdev->access_lock);
 }
 
 /**
@@ -351,7 +351,7 @@ static u8 ds2482_w1_read_byte(void *data)
 	struct ds2482_data    *pdev = pchan->pdev;
 	int result;
 
-	down(&pdev->access_lock);
+	mutex_lock(&pdev->access_lock);
 
 	/* Select the channel */
 	ds2482_wait_1wire_idle(pdev);
@@ -370,7 +370,7 @@ static u8 ds2482_w1_read_byte(void *data)
 	/* Read the data byte */
 	result = i2c_smbus_read_byte(&pdev->client);
 
-	up(&pdev->access_lock);
+	mutex_unlock(&pdev->access_lock);
 
 	return result;
 }
@@ -389,7 +389,7 @@ static u8 ds2482_w1_reset_bus(void *data)
 	int err;
 	u8 retval = 1;
 
-	down(&pdev->access_lock);
+	mutex_lock(&pdev->access_lock);
 
 	/* Select the channel */
 	ds2482_wait_1wire_idle(pdev);
@@ -409,7 +409,7 @@ static u8 ds2482_w1_reset_bus(void *data)
 					     0xF0);
 	}
 
-	up(&pdev->access_lock);
+	mutex_unlock(&pdev->access_lock);
 
 	return retval;
 }
@@ -482,7 +482,7 @@ static int ds2482_detect(struct i2c_adapter *adapter, int address, int kind)
 	snprintf(new_client->name, sizeof(new_client->name), "ds2482-%d00",
 		 data->w1_count);
 
-	init_MUTEX(&data->access_lock);
+	mutex_init(&data->access_lock);
 
 	/* Tell the I2C layer a new client has arrived */
 	if ((err = i2c_attach_client(new_client)))

drivers/w1/masters/dscore.c → drivers/w1/masters/ds2490.c

@@ -24,7 +24,136 @@
 #include <linux/mod_devicetable.h>
 #include <linux/usb.h>
 
-#include "dscore.h"
+#include "../w1_int.h"
+#include "../w1.h"
+
+/* COMMAND TYPE CODES */
+#define CONTROL_CMD			0x00
+#define COMM_CMD			0x01
+#define MODE_CMD			0x02
+
+/* CONTROL COMMAND CODES */
+#define CTL_RESET_DEVICE		0x0000
+#define CTL_START_EXE			0x0001
+#define CTL_RESUME_EXE			0x0002
+#define CTL_HALT_EXE_IDLE		0x0003
+#define CTL_HALT_EXE_DONE		0x0004
+#define CTL_FLUSH_COMM_CMDS		0x0007
+#define CTL_FLUSH_RCV_BUFFER		0x0008
+#define CTL_FLUSH_XMT_BUFFER		0x0009
+#define CTL_GET_COMM_CMDS		0x000A
+
+/* MODE COMMAND CODES */
+#define MOD_PULSE_EN			0x0000
+#define MOD_SPEED_CHANGE_EN		0x0001
+#define MOD_1WIRE_SPEED			0x0002
+#define MOD_STRONG_PU_DURATION		0x0003
+#define MOD_PULLDOWN_SLEWRATE		0x0004
+#define MOD_PROG_PULSE_DURATION		0x0005
+#define MOD_WRITE1_LOWTIME		0x0006
+#define MOD_DSOW0_TREC			0x0007
+
+/* COMMUNICATION COMMAND CODES */
+#define COMM_ERROR_ESCAPE		0x0601
+#define COMM_SET_DURATION		0x0012
+#define COMM_BIT_IO			0x0020
+#define COMM_PULSE			0x0030
+#define COMM_1_WIRE_RESET		0x0042
+#define COMM_BYTE_IO			0x0052
+#define COMM_MATCH_ACCESS		0x0064
+#define COMM_BLOCK_IO			0x0074
+#define COMM_READ_STRAIGHT		0x0080
+#define COMM_DO_RELEASE			0x6092
+#define COMM_SET_PATH			0x00A2
+#define COMM_WRITE_SRAM_PAGE		0x00B2
+#define COMM_WRITE_EPROM		0x00C4
+#define COMM_READ_CRC_PROT_PAGE		0x00D4
+#define COMM_READ_REDIRECT_PAGE_CRC	0x21E4
+#define COMM_SEARCH_ACCESS		0x00F4
+
+/* Communication command bits */
+#define COMM_TYPE			0x0008
+#define COMM_SE				0x0008
+#define COMM_D				0x0008
+#define COMM_Z				0x0008
+#define COMM_CH				0x0008
+#define COMM_SM				0x0008
+#define COMM_R				0x0008
+#define COMM_IM				0x0001
+
+#define COMM_PS				0x4000
+#define COMM_PST			0x4000
+#define COMM_CIB			0x4000
+#define COMM_RTS			0x4000
+#define COMM_DT				0x2000
+#define COMM_SPU			0x1000
+#define COMM_F				0x0800
+#define COMM_NTP			0x0400
+#define COMM_ICP			0x0200
+#define COMM_RST			0x0100
+
+#define PULSE_PROG			0x01
+#define PULSE_SPUE			0x02
+
+#define BRANCH_MAIN			0xCC
+#define BRANCH_AUX			0x33
+
+/*
+ * Duration of the strong pull-up pulse in milliseconds.
+ */
+#define PULLUP_PULSE_DURATION		750
+
+/* Status flags */
+#define ST_SPUA				0x01  /* Strong Pull-up is active */
+#define ST_PRGA				0x02  /* 12V programming pulse is being generated */
+#define ST_12VP				0x04  /* external 12V programming voltage is present */
+#define ST_PMOD				0x08  /* DS2490 powered from USB and external sources */
+#define ST_HALT				0x10  /* DS2490 is currently halted */
+#define ST_IDLE				0x20  /* DS2490 is currently idle */
+#define ST_EPOF				0x80
+
+#define SPEED_NORMAL			0x00
+#define SPEED_FLEXIBLE			0x01
+#define SPEED_OVERDRIVE			0x02
+
+#define NUM_EP				4
+#define EP_CONTROL			0
+#define EP_STATUS			1
+#define EP_DATA_OUT			2
+#define EP_DATA_IN			3
+
+struct ds_device
+{
+	struct list_head	ds_entry;
+
+	struct usb_device	*udev;
+	struct usb_interface	*intf;
+
+	int			ep[NUM_EP];
+
+	struct w1_bus_master	master;
+};
+
+struct ds_status
+{
+	u8			enable;
+	u8			speed;
+	u8			pullup_dur;
+	u8			ppuls_dur;
+	u8			pulldown_slew;
+	u8			write1_time;
+	u8			write0_time;
+	u8			reserved0;
+	u8			status;
+	u8			command0;
+	u8			command1;
+	u8			command_buffer_status;
+	u8			data_out_buffer_status;
+	u8			data_in_buffer_status;
+	u8			reserved1;
+	u8			reserved2;
+
+};
 
 static struct usb_device_id ds_id_table [] = {
 	{ USB_DEVICE(0x04fa, 0x2490) },
@@ -35,21 +164,12 @@ MODULE_DEVICE_TABLE(usb, ds_id_table);
 static int ds_probe(struct usb_interface *, const struct usb_device_id *);
 static void ds_disconnect(struct usb_interface *);
 
-int ds_touch_bit(struct ds_device *, u8, u8 *);
-int ds_read_byte(struct ds_device *, u8 *);
-int ds_read_bit(struct ds_device *, u8 *);
-int ds_write_byte(struct ds_device *, u8);
-int ds_write_bit(struct ds_device *, u8);
-static int ds_start_pulse(struct ds_device *, int);
-int ds_reset(struct ds_device *, struct ds_status *);
-struct ds_device * ds_get_device(void);
-void ds_put_device(struct ds_device *);
-
 static inline void ds_dump_status(unsigned char *, unsigned char *, int);
 static int ds_send_control(struct ds_device *, u16, u16);
-static int ds_send_control_mode(struct ds_device *, u16, u16);
 static int ds_send_control_cmd(struct ds_device *, u16, u16);
 
+static LIST_HEAD(ds_devices);
+static DEFINE_MUTEX(ds_mutex);
 
 static struct usb_driver ds_driver = {
 	.name =		"DS9490R",
@@ -58,20 +178,6 @@ static struct usb_driver ds_driver = {
 	.id_table =	ds_id_table,
 };
 
-static struct ds_device *ds_dev;
-
-struct ds_device * ds_get_device(void)
-{
-	if (ds_dev)
-		atomic_inc(&ds_dev->refcnt);
-	return ds_dev;
-}
-
-void ds_put_device(struct ds_device *dev)
-{
-	atomic_dec(&dev->refcnt);
-}
-
 static int ds_send_control_cmd(struct ds_device *dev, u16 value, u16 index)
 {
 	int err;
@@ -86,7 +192,7 @@ static int ds_send_control_cmd(struct ds_device *dev, u16 value, u16 index)
 
 	return err;
 }
-
+#if 0
 static int ds_send_control_mode(struct ds_device *dev, u16 value, u16 index)
 {
 	int err;
@@ -101,7 +207,7 @@ static int ds_send_control_mode(struct ds_device *dev, u16 value, u16 index)
 
 	return err;
 }
-
+#endif
 static int ds_send_control(struct ds_device *dev, u16 value, u16 index)
 {
 	int err;
@@ -324,7 +430,7 @@ static int ds_wait_status(struct ds_device *dev, struct ds_status *st)
 		return 0;
 }
 
-int ds_reset(struct ds_device *dev, struct ds_status *st)
+static int ds_reset(struct ds_device *dev, struct ds_status *st)
 {
 	int err;
 
@@ -345,7 +451,7 @@ int ds_reset(struct ds_device *dev, struct ds_status *st)
 }
 
 #if 0
-int ds_set_speed(struct ds_device *dev, int speed)
+static int ds_set_speed(struct ds_device *dev, int speed)
 {
 	int err;
 
@@ -395,7 +501,7 @@ static int ds_start_pulse(struct ds_device *dev, int delay)
 	return err;
 }
 
-int ds_touch_bit(struct ds_device *dev, u8 bit, u8 *tbit)
+static int ds_touch_bit(struct ds_device *dev, u8 bit, u8 *tbit)
 {
 	int err, count;
 	struct ds_status st;
@@ -427,7 +533,7 @@ int ds_touch_bit(struct ds_device *dev, u8 bit, u8 *tbit)
 	return 0;
 }
 
-int ds_write_bit(struct ds_device *dev, u8 bit)
+static int ds_write_bit(struct ds_device *dev, u8 bit)
 {
 	int err;
 	struct ds_status st;
@@ -441,7 +547,7 @@ int ds_write_bit(struct ds_device *dev, u8 bit)
 	return 0;
 }
 
-int ds_write_byte(struct ds_device *dev, u8 byte)
+static int ds_write_byte(struct ds_device *dev, u8 byte)
 {
 	int err;
 	struct ds_status st;
@@ -464,26 +570,7 @@ int ds_write_byte(struct ds_device *dev, u8 byte)
 	return !(byte == rbyte);
 }
 
-int ds_read_bit(struct ds_device *dev, u8 *bit)
-{
-	int err;
-
-	err = ds_send_control_mode(dev, MOD_PULSE_EN, PULSE_SPUE);
-	if (err)
-		return err;
-
-	err = ds_send_control(dev, COMM_BIT_IO | COMM_IM | COMM_SPU | COMM_D, 0);
-	if (err)
-		return err;
-
-	err = ds_recv_data(dev, bit, sizeof(*bit));
-	if (err < 0)
-		return err;
-
-	return 0;
-}
-
-int ds_read_byte(struct ds_device *dev, u8 *byte)
+static int ds_read_byte(struct ds_device *dev, u8 *byte)
 {
 	int err;
 	struct ds_status st;
@@ -501,7 +588,7 @@ int ds_read_byte(struct ds_device *dev, u8 *byte)
 	return 0;
 }
 
-int ds_read_block(struct ds_device *dev, u8 *buf, int len)
+static int ds_read_block(struct ds_device *dev, u8 *buf, int len)
 {
 	struct ds_status st;
 	int err;
@@ -527,7 +614,7 @@ int ds_read_block(struct ds_device *dev, u8 *buf, int len)
 	return err;
 }
 
-int ds_write_block(struct ds_device *dev, u8 *buf, int len)
+static int ds_write_block(struct ds_device *dev, u8 *buf, int len)
 {
 	int err;
 	struct ds_status st;
@@ -555,7 +642,7 @@ int ds_write_block(struct ds_device *dev, u8 *buf, int len)
 
 #if 0
 
-int ds_search(struct ds_device *dev, u64 init, u64 *buf, u8 id_number, int conditional_search)
+static int ds_search(struct ds_device *dev, u64 init, u64 *buf, u8 id_number, int conditional_search)
 {
 	int err;
 	u16 value, index;
@@ -584,7 +671,7 @@ int ds_search(struct ds_device *dev, u64 init, u64 *buf, u8 id_number, int condi
 	return err/8;
 }
 
-int ds_match_access(struct ds_device *dev, u64 init)
+static int ds_match_access(struct ds_device *dev, u64 init)
 {
 	int err;
 	struct ds_status st;
@@ -604,7 +691,7 @@ int ds_match_access(struct ds_device *dev, u64 init)
 	return 0;
 }
 
-int ds_set_path(struct ds_device *dev, u64 init)
+static int ds_set_path(struct ds_device *dev, u64 init)
 {
 	int err;
 	struct ds_status st;
@@ -630,45 +717,156 @@ int ds_set_path(struct ds_device *dev, u64 init)
 
 #endif  /*  0  */
 
+static u8 ds9490r_touch_bit(void *data, u8 bit)
+{
+	u8 ret;
+	struct ds_device *dev = data;
+
+	if (ds_touch_bit(dev, bit, &ret))
+		return 0;
+
+	return ret;
+}
+
+static void ds9490r_write_bit(void *data, u8 bit)
+{
+	struct ds_device *dev = data;
+
+	ds_write_bit(dev, bit);
+}
+
+static void ds9490r_write_byte(void *data, u8 byte)
+{
+	struct ds_device *dev = data;
+
+	ds_write_byte(dev, byte);
+}
+
+static u8 ds9490r_read_bit(void *data)
+{
+	struct ds_device *dev = data;
+	int err;
+	u8 bit = 0;
+
+	err = ds_touch_bit(dev, 1, &bit);
+	if (err)
+		return 0;
+
+	return bit & 1;
+}
+
+static u8 ds9490r_read_byte(void *data)
+{
+	struct ds_device *dev = data;
+	int err;
+	u8 byte = 0;
+
+	err = ds_read_byte(dev, &byte);
+	if (err)
+		return 0;
+
+	return byte;
+}
+
+static void ds9490r_write_block(void *data, const u8 *buf, int len)
+{
+	struct ds_device *dev = data;
+
+	ds_write_block(dev, (u8 *)buf, len);
+}
+
+static u8 ds9490r_read_block(void *data, u8 *buf, int len)
+{
+	struct ds_device *dev = data;
+	int err;
+
+	err = ds_read_block(dev, buf, len);
+	if (err < 0)
+		return 0;
+
+	return len;
+}
+
+static u8 ds9490r_reset(void *data)
+{
+	struct ds_device *dev = data;
+	struct ds_status st;
+	int err;
+
+	memset(&st, 0, sizeof(st));
+
+	err = ds_reset(dev, &st);
+	if (err)
+		return 1;
+
+	return 0;
+}
+
+static int ds_w1_init(struct ds_device *dev)
+{
+	memset(&dev->master, 0, sizeof(struct w1_bus_master));
+
+	dev->master.data	= dev;
+	dev->master.touch_bit	= &ds9490r_touch_bit;
+	dev->master.read_bit	= &ds9490r_read_bit;
+	dev->master.write_bit	= &ds9490r_write_bit;
+	dev->master.read_byte	= &ds9490r_read_byte;
+	dev->master.write_byte	= &ds9490r_write_byte;
+	dev->master.read_block	= &ds9490r_read_block;
+	dev->master.write_block	= &ds9490r_write_block;
+	dev->master.reset_bus	= &ds9490r_reset;
+
+	return w1_add_master_device(&dev->master);
+}
+
+static void ds_w1_fini(struct ds_device *dev)
+{
+	w1_remove_master_device(&dev->master);
+}
+
 static int ds_probe(struct usb_interface *intf,
 		    const struct usb_device_id *udev_id)
 {
 	struct usb_device *udev = interface_to_usbdev(intf);
 	struct usb_endpoint_descriptor *endpoint;
 	struct usb_host_interface *iface_desc;
+	struct ds_device *dev;
 	int i, err;
 
-	ds_dev = kmalloc(sizeof(struct ds_device), GFP_KERNEL);
-	if (!ds_dev) {
+	dev = kmalloc(sizeof(struct ds_device), GFP_KERNEL);
+	if (!dev) {
 		printk(KERN_INFO "Failed to allocate new DS9490R structure.\n");
 		return -ENOMEM;
 	}
+	dev->udev = usb_get_dev(udev);
+	if (!dev->udev) {
+		err = -ENOMEM;
+		goto err_out_free;
+	}
+	memset(dev->ep, 0, sizeof(dev->ep));
 
-	ds_dev->udev = usb_get_dev(udev);
-	usb_set_intfdata(intf, ds_dev);
+	usb_set_intfdata(intf, dev);
 
-	err = usb_set_interface(ds_dev->udev, intf->altsetting[0].desc.bInterfaceNumber, 3);
+	err = usb_set_interface(dev->udev, intf->altsetting[0].desc.bInterfaceNumber, 3);
 	if (err) {
 		printk(KERN_ERR "Failed to set alternative setting 3 for %d interface: err=%d.\n",
 				intf->altsetting[0].desc.bInterfaceNumber, err);
-		return err;
+		goto err_out_clear;
 	}
 
-	err = usb_reset_configuration(ds_dev->udev);
+	err = usb_reset_configuration(dev->udev);
 	if (err) {
 		printk(KERN_ERR "Failed to reset configuration: err=%d.\n", err);
-		return err;
+		goto err_out_clear;
 	}
 
 	iface_desc = &intf->altsetting[0];
 	if (iface_desc->desc.bNumEndpoints != NUM_EP-1) {
 		printk(KERN_INFO "Num endpoints=%d. It is not DS9490R.\n", iface_desc->desc.bNumEndpoints);
-		return -ENODEV;
+		err = -EINVAL;
+		goto err_out_clear;
 	}
 
-	atomic_set(&ds_dev->refcnt, 0);
-	memset(ds_dev->ep, 0, sizeof(ds_dev->ep));
-
 	/*
 	 * This loop doesn'd show control 0 endpoint,
 	 * so we will fill only 1-3 endpoints entry.
@@ -676,54 +874,31 @@ static int ds_probe(struct usb_interface *intf,
 	for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
 		endpoint = &iface_desc->endpoint[i].desc;
 
-		ds_dev->ep[i+1] = endpoint->bEndpointAddress;
-
+		dev->ep[i+1] = endpoint->bEndpointAddress;
+#if 0
 		printk("%d: addr=%x, size=%d, dir=%s, type=%x\n",
 			i, endpoint->bEndpointAddress, le16_to_cpu(endpoint->wMaxPacketSize),
 			(endpoint->bEndpointAddress & USB_DIR_IN)?"IN":"OUT",
 			endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK);
+#endif
 	}
 
-#if 0
-	{
-		int err, i;
-		u64 buf[3];
-		u64 init=0xb30000002078ee81ull;
-		struct ds_status st;
-
-		ds_reset(ds_dev, &st);
-		err = ds_search(ds_dev, init, buf, 3, 0);
-		if (err < 0)
-			return err;
-		for (i=0; i<err; ++i)
-			printk("%d: %llx\n", i, buf[i]);
-
-		printk("Resetting...\n");
-		ds_reset(ds_dev, &st);
-		printk("Setting path for %llx.\n", init);
-		err = ds_set_path(ds_dev, init);
-		if (err)
-			return err;
-		printk("Calling MATCH_ACCESS.\n");
-		err = ds_match_access(ds_dev, init);
-		if (err)
-			return err;
-
-		printk("Searching the bus...\n");
-		err = ds_search(ds_dev, init, buf, 3, 0);
-
-		printk("ds_search() returned %d\n", err);
-
-		if (err < 0)
-			return err;
-		for (i=0; i<err; ++i)
-			printk("%d: %llx\n", i, buf[i]);
+	err = ds_w1_init(dev);
+	if (err)
+		goto err_out_clear;
 
-		return 0;
-	}
-#endif
+	mutex_lock(&ds_mutex);
+	list_add_tail(&dev->ds_entry, &ds_devices);
+	mutex_unlock(&ds_mutex);
 
 	return 0;
+
+err_out_clear:
+	usb_set_intfdata(intf, NULL);
+	usb_put_dev(dev->udev);
+err_out_free:
+	kfree(dev);
+	return err;
 }
 
 static void ds_disconnect(struct usb_interface *intf)
@@ -731,19 +906,19 @@ static void ds_disconnect(struct usb_interface *intf)
 	struct ds_device *dev;
 
 	dev = usb_get_intfdata(intf);
-	usb_set_intfdata(intf, NULL);
+	if (!dev)
+		return;
 
-	while (atomic_read(&dev->refcnt)) {
-		printk(KERN_INFO "Waiting for DS to become free: refcnt=%d.\n",
-				atomic_read(&dev->refcnt));
+	mutex_lock(&ds_mutex);
+	list_del(&dev->ds_entry);
+	mutex_unlock(&ds_mutex);
 
-		if (msleep_interruptible(1000))
-			flush_signals(current);
-	}
+	ds_w1_fini(dev);
+
+	usb_set_intfdata(intf, NULL);
 
 	usb_put_dev(dev->udev);
 	kfree(dev);
-	ds_dev = NULL;
 }
 
 static int ds_init(void)
@@ -769,27 +944,4 @@ module_exit(ds_fini);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>");
-
-EXPORT_SYMBOL(ds_touch_bit);
-EXPORT_SYMBOL(ds_read_byte);
-EXPORT_SYMBOL(ds_read_bit);
-EXPORT_SYMBOL(ds_read_block);
-EXPORT_SYMBOL(ds_write_byte);
-EXPORT_SYMBOL(ds_write_bit);
-EXPORT_SYMBOL(ds_write_block);
-EXPORT_SYMBOL(ds_reset);
-EXPORT_SYMBOL(ds_get_device);
-EXPORT_SYMBOL(ds_put_device);
-
-/*
- * This functions can be used for EEPROM programming,
- * when driver will be included into mainline this will
- * require uncommenting.
- */
-#if 0
-EXPORT_SYMBOL(ds_start_pulse);
-EXPORT_SYMBOL(ds_set_speed);
-EXPORT_SYMBOL(ds_detect);
-EXPORT_SYMBOL(ds_stop_pulse);
-EXPORT_SYMBOL(ds_search);
-#endif
+MODULE_DESCRIPTION("DS2490 USB <-> W1 bus master driver (DS9490*)");

drivers/w1/masters/ds_w1_bridge.c

@@ -1,174 +0,0 @@
-/*
- *	ds_w1_bridge.c
- *
- * Copyright (c) 2004 Evgeniy Polyakov <johnpol@2ka.mipt.ru>
- *
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-
-#include "../w1.h"
-#include "../w1_int.h"
-#include "dscore.h"
-
-static struct ds_device *ds_dev;
-static struct w1_bus_master *ds_bus_master;
-
-static u8 ds9490r_touch_bit(void *data, u8 bit)
-{
-	u8 ret;
-	struct ds_device *dev = data;
-
-	if (ds_touch_bit(dev, bit, &ret))
-		return 0;
-
-	return ret;
-}
-
-static void ds9490r_write_bit(void *data, u8 bit)
-{
-	struct ds_device *dev = data;
-
-	ds_write_bit(dev, bit);
-}
-
-static void ds9490r_write_byte(void *data, u8 byte)
-{
-	struct ds_device *dev = data;
-
-	ds_write_byte(dev, byte);
-}
-
-static u8 ds9490r_read_bit(void *data)
-{
-	struct ds_device *dev = data;
-	int err;
-	u8 bit = 0;
-
-	err = ds_touch_bit(dev, 1, &bit);
-	if (err)
-		return 0;
-	//err = ds_read_bit(dev, &bit);
-	//if (err)
-	//	return 0;
-
-	return bit & 1;
-}
-
-static u8 ds9490r_read_byte(void *data)
-{
-	struct ds_device *dev = data;
-	int err;
-	u8 byte = 0;
-
-	err = ds_read_byte(dev, &byte);
-	if (err)
-		return 0;
-
-	return byte;
-}
-
-static void ds9490r_write_block(void *data, const u8 *buf, int len)
-{
-	struct ds_device *dev = data;
-
-	ds_write_block(dev, (u8 *)buf, len);
-}
-
-static u8 ds9490r_read_block(void *data, u8 *buf, int len)
-{
-	struct ds_device *dev = data;
-	int err;
-
-	err = ds_read_block(dev, buf, len);
-	if (err < 0)
-		return 0;
-
-	return len;
-}
-
-static u8 ds9490r_reset(void *data)
-{
-	struct ds_device *dev = data;
-	struct ds_status st;
-	int err;
-
-	memset(&st, 0, sizeof(st));
-
-	err = ds_reset(dev, &st);
-	if (err)
-		return 1;
-
-	return 0;
-}
-
-static int __devinit ds_w1_init(void)
-{
-	int err;
-
-	ds_bus_master = kmalloc(sizeof(*ds_bus_master), GFP_KERNEL);
-	if (!ds_bus_master) {
-		printk(KERN_ERR "Failed to allocate DS9490R USB<->W1 bus_master structure.\n");
-		return -ENOMEM;
-	}
-
-	ds_dev = ds_get_device();
-	if (!ds_dev) {
-		printk(KERN_ERR "DS9490R is not registered.\n");
-		err =  -ENODEV;
-		goto err_out_free_bus_master;
-	}
-
-	memset(ds_bus_master, 0, sizeof(*ds_bus_master));
-
-	ds_bus_master->data		= ds_dev;
-	ds_bus_master->touch_bit	= &ds9490r_touch_bit;
-	ds_bus_master->read_bit		= &ds9490r_read_bit;
-	ds_bus_master->write_bit	= &ds9490r_write_bit;
-	ds_bus_master->read_byte	= &ds9490r_read_byte;
-	ds_bus_master->write_byte	= &ds9490r_write_byte;
-	ds_bus_master->read_block	= &ds9490r_read_block;
-	ds_bus_master->write_block	= &ds9490r_write_block;
-	ds_bus_master->reset_bus	= &ds9490r_reset;
-
-	err = w1_add_master_device(ds_bus_master);
-	if (err)
-		goto err_out_put_device;
-
-	return 0;
-
-err_out_put_device:
-	ds_put_device(ds_dev);
-err_out_free_bus_master:
-	kfree(ds_bus_master);
-
-	return err;
-}
-
-static void __devexit ds_w1_fini(void)
-{
-	w1_remove_master_device(ds_bus_master);
-	ds_put_device(ds_dev);
-	kfree(ds_bus_master);
-}
-
-module_init(ds_w1_init);
-module_exit(ds_w1_fini);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>");

drivers/w1/masters/dscore.h

@@ -1,166 +0,0 @@
-/*
- *	dscore.h
- *
- * Copyright (c) 2004 Evgeniy Polyakov <johnpol@2ka.mipt.ru>
- *
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#ifndef __DSCORE_H
-#define __DSCORE_H
-
-#include <linux/usb.h>
-#include <asm/atomic.h>
-
-/* COMMAND TYPE CODES */
-#define CONTROL_CMD			0x00
-#define COMM_CMD			0x01
-#define MODE_CMD			0x02
-
-/* CONTROL COMMAND CODES */
-#define CTL_RESET_DEVICE		0x0000
-#define CTL_START_EXE			0x0001
-#define CTL_RESUME_EXE			0x0002
-#define CTL_HALT_EXE_IDLE		0x0003
-#define CTL_HALT_EXE_DONE		0x0004
-#define CTL_FLUSH_COMM_CMDS		0x0007
-#define CTL_FLUSH_RCV_BUFFER		0x0008
-#define CTL_FLUSH_XMT_BUFFER		0x0009
-#define CTL_GET_COMM_CMDS		0x000A
-
-/* MODE COMMAND CODES */
-#define MOD_PULSE_EN			0x0000
-#define MOD_SPEED_CHANGE_EN		0x0001
-#define MOD_1WIRE_SPEED			0x0002
-#define MOD_STRONG_PU_DURATION		0x0003
-#define MOD_PULLDOWN_SLEWRATE		0x0004
-#define MOD_PROG_PULSE_DURATION		0x0005
-#define MOD_WRITE1_LOWTIME		0x0006
-#define MOD_DSOW0_TREC			0x0007
-
-/* COMMUNICATION COMMAND CODES */
-#define COMM_ERROR_ESCAPE		0x0601
-#define COMM_SET_DURATION		0x0012
-#define COMM_BIT_IO			0x0020
-#define COMM_PULSE			0x0030
-#define COMM_1_WIRE_RESET		0x0042
-#define COMM_BYTE_IO			0x0052
-#define COMM_MATCH_ACCESS		0x0064
-#define COMM_BLOCK_IO			0x0074
-#define COMM_READ_STRAIGHT		0x0080
-#define COMM_DO_RELEASE			0x6092
-#define COMM_SET_PATH			0x00A2
-#define COMM_WRITE_SRAM_PAGE		0x00B2
-#define COMM_WRITE_EPROM		0x00C4
-#define COMM_READ_CRC_PROT_PAGE		0x00D4
-#define COMM_READ_REDIRECT_PAGE_CRC	0x21E4
-#define COMM_SEARCH_ACCESS		0x00F4
-
-/* Communication command bits */
-#define COMM_TYPE			0x0008
-#define COMM_SE				0x0008
-#define COMM_D				0x0008
-#define COMM_Z				0x0008
-#define COMM_CH				0x0008
-#define COMM_SM				0x0008
-#define COMM_R				0x0008
-#define COMM_IM				0x0001
-
-#define COMM_PS				0x4000
-#define COMM_PST			0x4000
-#define COMM_CIB			0x4000
-#define COMM_RTS			0x4000
-#define COMM_DT				0x2000
-#define COMM_SPU			0x1000
-#define COMM_F				0x0800
-#define COMM_NTP			0x0400
-#define COMM_ICP			0x0200
-#define COMM_RST			0x0100
-
-#define PULSE_PROG			0x01
-#define PULSE_SPUE			0x02
-
-#define BRANCH_MAIN			0xCC
-#define BRANCH_AUX			0x33
-
-/*
- * Duration of the strong pull-up pulse in milliseconds.
- */
-#define PULLUP_PULSE_DURATION		750
-
-/* Status flags */
-#define ST_SPUA				0x01  /* Strong Pull-up is active */
-#define ST_PRGA				0x02  /* 12V programming pulse is being generated */
-#define ST_12VP				0x04  /* external 12V programming voltage is present */
-#define ST_PMOD				0x08  /* DS2490 powered from USB and external sources */
-#define ST_HALT				0x10  /* DS2490 is currently halted */
-#define ST_IDLE				0x20  /* DS2490 is currently idle */
-#define ST_EPOF				0x80
-
-#define SPEED_NORMAL			0x00
-#define SPEED_FLEXIBLE			0x01
-#define SPEED_OVERDRIVE			0x02
-
-#define NUM_EP				4
-#define EP_CONTROL			0
-#define EP_STATUS			1
-#define EP_DATA_OUT			2
-#define EP_DATA_IN			3
-
-struct ds_device
-{
-	struct usb_device	*udev;
-	struct usb_interface	*intf;
-
-	int			ep[NUM_EP];
-
-	atomic_t		refcnt;
-};
-
-struct ds_status
-{
-	u8			enable;
-	u8			speed;
-	u8			pullup_dur;
-	u8			ppuls_dur;
-	u8			pulldown_slew;
-	u8			write1_time;
-	u8			write0_time;
-	u8			reserved0;
-	u8			status;
-	u8			command0;
-	u8			command1;
-	u8			command_buffer_status;
-	u8			data_out_buffer_status;
-	u8			data_in_buffer_status;
-	u8			reserved1;
-	u8			reserved2;
-
-};
-
-int ds_touch_bit(struct ds_device *, u8, u8 *);
-int ds_read_byte(struct ds_device *, u8 *);
-int ds_read_bit(struct ds_device *, u8 *);
-int ds_write_byte(struct ds_device *, u8);
-int ds_write_bit(struct ds_device *, u8);
-int ds_reset(struct ds_device *, struct ds_status *);
-struct ds_device * ds_get_device(void);
-void ds_put_device(struct ds_device *);
-int ds_write_block(struct ds_device *, u8 *, int);
-int ds_read_block(struct ds_device *, u8 *, int);
-
-#endif /* __DSCORE_H */
-

drivers/w1/slaves/Kconfig

@@ -28,7 +28,7 @@ config W1_SLAVE_DS2433
 
 config W1_SLAVE_DS2433_CRC
 	bool "Protect DS2433 data with a CRC16"
-	depends on W1_DS2433
+	depends on W1_SLAVE_DS2433
 	select CRC16
 	help
 	  Say Y here to protect DS2433 data with a CRC16.

drivers/w1/slaves/w1_ds2433.c

@@ -22,7 +22,6 @@
 #endif
 
 #include "../w1.h"
-#include "../w1_io.h"
 #include "../w1_int.h"
 #include "../w1_family.h"
 
@@ -106,11 +105,7 @@ static ssize_t w1_f23_read_bin(struct kobject *kobj, char *buf, loff_t off,
 	if ((count = w1_f23_fix_count(off, count, W1_EEPROM_SIZE)) == 0)
 		return 0;
 
-	atomic_inc(&sl->refcnt);
-	if (down_interruptible(&sl->master->mutex)) {
-		count = 0;
-		goto out_dec;
-	}
+	mutex_lock(&sl->master->mutex);
 
 #ifdef CONFIG_W1_F23_CRC
 
@@ -141,9 +136,7 @@ static ssize_t w1_f23_read_bin(struct kobject *kobj, char *buf, loff_t off,
 #endif	/* CONFIG_W1_F23_CRC */
 
 out_up:
-	up(&sl->master->mutex);
-out_dec:
-	atomic_dec(&sl->refcnt);
+	mutex_unlock(&sl->master->mutex);
 
 	return count;
 }
@@ -232,11 +225,7 @@ static ssize_t w1_f23_write_bin(struct kobject *kobj, char *buf, loff_t off,
 	}
 #endif	/* CONFIG_W1_F23_CRC */
 
-	atomic_inc(&sl->refcnt);
-	if (down_interruptible(&sl->master->mutex)) {
-		count = 0;
-		goto out_dec;
-	}
+	mutex_lock(&sl->master->mutex);
 
 	/* Can only write data to one page at a time */
 	idx = 0;
@@ -254,9 +243,7 @@ static ssize_t w1_f23_write_bin(struct kobject *kobj, char *buf, loff_t off,
 	}
 
 out_up:
-	up(&sl->master->mutex);
-out_dec:
-	atomic_dec(&sl->refcnt);
+	mutex_unlock(&sl->master->mutex);
 
 	return count;
 }

drivers/w1/slaves/w1_smem.c

@@ -28,7 +28,6 @@
 #include <linux/types.h>
 
 #include "../w1.h"
-#include "../w1_io.h"
 #include "../w1_int.h"
 #include "../w1_family.h"
 

drivers/w1/slaves/w1_therm.c

@@ -29,7 +29,6 @@
 #include <linux/delay.h>
 
 #include "../w1.h"
-#include "../w1_io.h"
 #include "../w1_int.h"
 #include "../w1_family.h"
 
@@ -166,12 +165,7 @@ static ssize_t w1_therm_read_bin(struct kobject *kobj, char *buf, loff_t off, si
 	u8 rom[9], crc, verdict;
 	int i, max_trying = 10;
 
-	atomic_inc(&sl->refcnt);
-	smp_mb__after_atomic_inc();
-	if (down_interruptible(&sl->master->mutex)) {
-		count = 0;
-		goto out_dec;
-	}
+	mutex_lock(&sl->master->mutex);
 
 	if (off > W1_SLAVE_DATA_SIZE) {
 		count = 0;
@@ -234,10 +228,7 @@ static ssize_t w1_therm_read_bin(struct kobject *kobj, char *buf, loff_t off, si
 
 	count += sprintf(buf + count, "t=%d\n", w1_convert_temp(rom, sl->family->fid));
 out:
-	up(&dev->mutex);
-out_dec:
-	smp_mb__before_atomic_inc();
-	atomic_dec(&sl->refcnt);
+	mutex_unlock(&dev->mutex);
 
 	return count;
 }

drivers/w1/w1.c

@@ -35,7 +35,6 @@
 #include <asm/atomic.h>
 
 #include "w1.h"
-#include "w1_io.h"
 #include "w1_log.h"
 #include "w1_int.h"
 #include "w1_family.h"
@@ -55,7 +54,7 @@ module_param_named(control_timeout, w1_control_timeout, int, 0);
 module_param_named(max_slave_count, w1_max_slave_count, int, 0);
 module_param_named(slave_ttl, w1_max_slave_ttl, int, 0);
 
-DEFINE_SPINLOCK(w1_mlock);
+DEFINE_MUTEX(w1_mlock);
 LIST_HEAD(w1_masters);
 
 static struct task_struct *w1_control_thread;
@@ -75,8 +74,6 @@ static void w1_master_release(struct device *dev)
 	struct w1_master *md = dev_to_w1_master(dev);
 
 	dev_dbg(dev, "%s: Releasing %s.\n", __func__, md->name);
-
-	dev_fini_netlink(md);
 	memset(md, 0, sizeof(struct w1_master) + sizeof(struct w1_bus_master));
 	kfree(md);
 }
@@ -85,10 +82,10 @@ static void w1_slave_release(struct device *dev)
 {
 	struct w1_slave *sl = dev_to_w1_slave(dev);
 
-	dev_dbg(dev, "%s: Releasing %s.\n", __func__, sl->name);
+	printk("%s: Releasing %s.\n", __func__, sl->name);
 
 	while (atomic_read(&sl->refcnt)) {
-		dev_dbg(dev, "Waiting for %s to become free: refcnt=%d.\n",
+		printk("Waiting for %s to become free: refcnt=%d.\n",
 				sl->name, atomic_read(&sl->refcnt));
 		if (msleep_interruptible(1000))
 			flush_signals(current);
@@ -111,7 +108,6 @@ static ssize_t w1_slave_read_id(struct kobject *kobj, char *buf, loff_t off, siz
 {
 	struct w1_slave *sl = kobj_to_w1_slave(kobj);
 
-	atomic_inc(&sl->refcnt);
 	if (off > 8) {
 		count = 0;
 	} else {
@@ -120,7 +116,6 @@ static ssize_t w1_slave_read_id(struct kobject *kobj, char *buf, loff_t off, siz
 
 		memcpy(buf, (u8 *)&sl->reg_num, count);
 	}
-	atomic_dec(&sl->refcnt);
 
 	return count;
 }
@@ -139,7 +134,63 @@ static struct bin_attribute w1_slave_attr_bin_id = {
 };
 
 /* Default family */
-static struct w1_family w1_default_family;
+
+static ssize_t w1_default_write(struct kobject *kobj, char *buf, loff_t off, size_t count)
+{
+	struct w1_slave *sl = kobj_to_w1_slave(kobj);
+
+	mutex_lock(&sl->master->mutex);
+	if (w1_reset_select_slave(sl)) {
+		count = 0;
+		goto out_up;
+	}
+
+	w1_write_block(sl->master, buf, count);
+
+out_up:
+	mutex_unlock(&sl->master->mutex);
+	return count;
+}
+
+static ssize_t w1_default_read(struct kobject *kobj, char *buf, loff_t off, size_t count)
+{
+	struct w1_slave *sl = kobj_to_w1_slave(kobj);
+
+	mutex_lock(&sl->master->mutex);
+	w1_read_block(sl->master, buf, count);
+	mutex_unlock(&sl->master->mutex);
+	return count;
+}
+
+static struct bin_attribute w1_default_attr = {
+      .attr = {
+              .name = "rw",
+              .mode = S_IRUGO | S_IWUSR,
+              .owner = THIS_MODULE,
+      },
+      .size = PAGE_SIZE,
+      .read = w1_default_read,
+      .write = w1_default_write,
+};
+
+static int w1_default_add_slave(struct w1_slave *sl)
+{
+	return sysfs_create_bin_file(&sl->dev.kobj, &w1_default_attr);
+}
+
+static void w1_default_remove_slave(struct w1_slave *sl)
+{
+	sysfs_remove_bin_file(&sl->dev.kobj, &w1_default_attr);
+}
+
+static struct w1_family_ops w1_default_fops = {
+	.add_slave	= w1_default_add_slave,
+	.remove_slave	= w1_default_remove_slave,
+};
+
+static struct w1_family w1_default_family = {
+	.fops = &w1_default_fops,
+};
 
 static int w1_uevent(struct device *dev, char **envp, int num_envp, char *buffer, int buffer_size);
 
@@ -183,12 +234,9 @@ static ssize_t w1_master_attribute_show_name(struct device *dev, struct device_a
 	struct w1_master *md = dev_to_w1_master(dev);
 	ssize_t count;
 
-	if (down_interruptible (&md->mutex))
-		return -EBUSY;
-
+	mutex_lock(&md->mutex);
 	count = sprintf(buf, "%s\n", md->name);
-
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 
 	return count;
 }
@@ -199,12 +247,9 @@ static ssize_t w1_master_attribute_store_search(struct device * dev,
 {
 	struct w1_master *md = dev_to_w1_master(dev);
 
-	if (down_interruptible (&md->mutex))
-		return -EBUSY;
-
+	mutex_lock(&md->mutex);
 	md->search_count = simple_strtol(buf, NULL, 0);
-
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 
 	return count;
 }
@@ -216,12 +261,9 @@ static ssize_t w1_master_attribute_show_search(struct device *dev,
 	struct w1_master *md = dev_to_w1_master(dev);
 	ssize_t count;
 
-	if (down_interruptible (&md->mutex))
-		return -EBUSY;
-
+	mutex_lock(&md->mutex);
 	count = sprintf(buf, "%d\n", md->search_count);
-
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 
 	return count;
 }
@@ -231,12 +273,9 @@ static ssize_t w1_master_attribute_show_pointer(struct device *dev, struct devic
 	struct w1_master *md = dev_to_w1_master(dev);
 	ssize_t count;
 
-	if (down_interruptible(&md->mutex))
-		return -EBUSY;
-
+	mutex_lock(&md->mutex);
 	count = sprintf(buf, "0x%p\n", md->bus_master);
-
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 	return count;
 }
 
@@ -252,12 +291,9 @@ static ssize_t w1_master_attribute_show_max_slave_count(struct device *dev, stru
 	struct w1_master *md = dev_to_w1_master(dev);
 	ssize_t count;
 
-	if (down_interruptible(&md->mutex))
-		return -EBUSY;
-
+	mutex_lock(&md->mutex);
 	count = sprintf(buf, "%d\n", md->max_slave_count);
-
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 	return count;
 }
 
@@ -266,12 +302,9 @@ static ssize_t w1_master_attribute_show_attempts(struct device *dev, struct devi
 	struct w1_master *md = dev_to_w1_master(dev);
 	ssize_t count;
 
-	if (down_interruptible(&md->mutex))
-		return -EBUSY;
-
+	mutex_lock(&md->mutex);
 	count = sprintf(buf, "%lu\n", md->attempts);
-
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 	return count;
 }
 
@@ -280,12 +313,9 @@ static ssize_t w1_master_attribute_show_slave_count(struct device *dev, struct d
 	struct w1_master *md = dev_to_w1_master(dev);
 	ssize_t count;
 
-	if (down_interruptible(&md->mutex))
-		return -EBUSY;
-
+	mutex_lock(&md->mutex);
 	count = sprintf(buf, "%d\n", md->slave_count);
-
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 	return count;
 }
 
@@ -294,8 +324,7 @@ static ssize_t w1_master_attribute_show_slaves(struct device *dev, struct device
 	struct w1_master *md = dev_to_w1_master(dev);
 	int c = PAGE_SIZE;
 
-	if (down_interruptible(&md->mutex))
-		return -EBUSY;
+	mutex_lock(&md->mutex);
 
 	if (md->slave_count == 0)
 		c -= snprintf(buf + PAGE_SIZE - c, c, "not found.\n");
@@ -310,7 +339,7 @@ static ssize_t w1_master_attribute_show_slaves(struct device *dev, struct device
 		}
 	}
 
-	up(&md->mutex);
+	mutex_unlock(&md->mutex);
 
 	return PAGE_SIZE - c;
 }
@@ -362,7 +391,8 @@ static void w1_destroy_master_attributes(struct w1_master *master)
 }
 
 #ifdef CONFIG_HOTPLUG
-static int w1_uevent(struct device *dev, char **envp, int num_envp, char *buffer, int buffer_size)
+static int w1_uevent(struct device *dev, char **envp, int num_envp,
+			char *buffer, int buffer_size)
 {
 	struct w1_master *md = NULL;
 	struct w1_slave *sl = NULL;
@@ -382,7 +412,8 @@ static int w1_uevent(struct device *dev, char **envp, int num_envp, char *buffer
 		return -EINVAL;
 	}
 
-	dev_dbg(dev, "Hotplug event for %s %s, bus_id=%s.\n", event_owner, name, dev->bus_id);
+	dev_dbg(dev, "Hotplug event for %s %s, bus_id=%s.\n",
+			event_owner, name, dev->bus_id);
 
 	if (dev->driver != &w1_slave_driver || !sl)
 		return 0;
@@ -401,7 +432,8 @@ static int w1_uevent(struct device *dev, char **envp, int num_envp, char *buffer
 	return 0;
 };
 #else
-static int w1_uevent(struct device *dev, char **envp, int num_envp, char *buffer, int buffer_size)
+static int w1_uevent(struct device *dev, char **envp, int num_envp,
+			char *buffer, int buffer_size)
 {
 	return 0;
 }
@@ -425,7 +457,8 @@ static int __w1_attach_slave_device(struct w1_slave *sl)
 		 (unsigned int) sl->reg_num.family,
 		 (unsigned long long) sl->reg_num.id);
 
-	dev_dbg(&sl->dev, "%s: registering %s as %p.\n", __func__, &sl->dev.bus_id[0]);
+	dev_dbg(&sl->dev, "%s: registering %s as %p.\n", __func__,
+		&sl->dev.bus_id[0]);
 
 	err = device_register(&sl->dev);
 	if (err < 0) {
@@ -496,6 +529,7 @@ static int w1_attach_slave_device(struct w1_master *dev, struct w1_reg_num *rn)
 	sl->master = dev;
 	set_bit(W1_SLAVE_ACTIVE, (long *)&sl->flags);
 
+	memset(&msg, 0, sizeof(msg));
 	memcpy(&sl->reg_num, rn, sizeof(sl->reg_num));
 	atomic_set(&sl->refcnt, 0);
 	init_completion(&sl->released);
@@ -526,7 +560,7 @@ static int w1_attach_slave_device(struct w1_master *dev, struct w1_reg_num *rn)
 	sl->ttl = dev->slave_ttl;
 	dev->slave_count++;
 
-	memcpy(&msg.id.id, rn, sizeof(msg.id.id));
+	memcpy(msg.id.id, rn, sizeof(msg.id));
 	msg.type = W1_SLAVE_ADD;
 	w1_netlink_send(dev, &msg);
 
@@ -544,7 +578,8 @@ static void w1_slave_detach(struct w1_slave *sl)
 	if (sl->family->fops && sl->family->fops->remove_slave)
 		sl->family->fops->remove_slave(sl);
 
-	memcpy(&msg.id.id, &sl->reg_num, sizeof(msg.id.id));
+	memset(&msg, 0, sizeof(msg));
+	memcpy(msg.id.id, &sl->reg_num, sizeof(msg.id));
 	msg.type = W1_SLAVE_REMOVE;
 	w1_netlink_send(sl->master, &msg);
 
@@ -561,7 +596,7 @@ static struct w1_master *w1_search_master(void *data)
 	struct w1_master *dev;
 	int found = 0;
 
-	spin_lock_bh(&w1_mlock);
+	mutex_lock(&w1_mlock);
 	list_for_each_entry(dev, &w1_masters, w1_master_entry) {
 		if (dev->bus_master->data == data) {
 			found = 1;
@@ -569,22 +604,69 @@ static struct w1_master *w1_search_master(void *data)
 			break;
 		}
 	}
-	spin_unlock_bh(&w1_mlock);
+	mutex_unlock(&w1_mlock);
+
+	return (found)?dev:NULL;
+}
+
+struct w1_master *w1_search_master_id(u32 id)
+{
+	struct w1_master *dev;
+	int found = 0;
+
+	mutex_lock(&w1_mlock);
+	list_for_each_entry(dev, &w1_masters, w1_master_entry) {
+		if (dev->id == id) {
+			found = 1;
+			atomic_inc(&dev->refcnt);
+			break;
+		}
+	}
+	mutex_unlock(&w1_mlock);
 
 	return (found)?dev:NULL;
 }
 
+struct w1_slave *w1_search_slave(struct w1_reg_num *id)
+{
+	struct w1_master *dev;
+	struct w1_slave *sl = NULL;
+	int found = 0;
+
+	mutex_lock(&w1_mlock);
+	list_for_each_entry(dev, &w1_masters, w1_master_entry) {
+		mutex_lock(&dev->mutex);
+		list_for_each_entry(sl, &dev->slist, w1_slave_entry) {
+			if (sl->reg_num.family == id->family &&
+					sl->reg_num.id == id->id &&
+					sl->reg_num.crc == id->crc) {
+				found = 1;
+				atomic_inc(&dev->refcnt);
+				atomic_inc(&sl->refcnt);
+				break;
+			}
+		}
+		mutex_unlock(&dev->mutex);
+
+		if (found)
+			break;
+	}
+	mutex_unlock(&w1_mlock);
+
+	return (found)?sl:NULL;
+}
+
 void w1_reconnect_slaves(struct w1_family *f)
 {
 	struct w1_master *dev;
 
-	spin_lock_bh(&w1_mlock);
+	mutex_lock(&w1_mlock);
 	list_for_each_entry(dev, &w1_masters, w1_master_entry) {
 		dev_dbg(&dev->dev, "Reconnecting slaves in %s into new family %02x.\n",
 				dev->name, f->fid);
 		set_bit(W1_MASTER_NEED_RECONNECT, &dev->flags);
 	}
-	spin_unlock_bh(&w1_mlock);
+	mutex_unlock(&w1_mlock);
 }
 
 static void w1_slave_found(void *data, u64 rn)
@@ -646,7 +728,7 @@ static void w1_slave_found(void *data, u64 rn)
  * @dev        The master device to search
  * @cb         Function to call when a device is found
  */
-void w1_search(struct w1_master *dev, w1_slave_found_callback cb)
+void w1_search(struct w1_master *dev, u8 search_type, w1_slave_found_callback cb)
 {
 	u64 last_rn, rn, tmp64;
 	int i, slave_count = 0;
@@ -677,7 +759,7 @@ void w1_search(struct w1_master *dev, w1_slave_found_callback cb)
 		}
 
 		/* Start the search */
-		w1_write_8(dev, W1_SEARCH);
+		w1_write_8(dev, search_type);
 		for (i = 0; i < 64; ++i) {
 			/* Determine the direction/search bit */
 			if (i == desc_bit)
@@ -739,23 +821,23 @@ static int w1_control(void *data)
 			if (kthread_should_stop() || test_bit(W1_MASTER_NEED_EXIT, &dev->flags)) {
 				set_bit(W1_MASTER_NEED_EXIT, &dev->flags);
 
-				spin_lock(&w1_mlock);
+				mutex_lock(&w1_mlock);
 				list_del(&dev->w1_master_entry);
-				spin_unlock(&w1_mlock);
+				mutex_unlock(&w1_mlock);
 
-				down(&dev->mutex);
+				mutex_lock(&dev->mutex);
 				list_for_each_entry_safe(sl, sln, &dev->slist, w1_slave_entry) {
 					w1_slave_detach(sl);
 				}
 				w1_destroy_master_attributes(dev);
-				up(&dev->mutex);
+				mutex_unlock(&dev->mutex);
 				atomic_dec(&dev->refcnt);
 				continue;
 			}
 
 			if (test_bit(W1_MASTER_NEED_RECONNECT, &dev->flags)) {
 				dev_dbg(&dev->dev, "Reconnecting slaves in device %s.\n", dev->name);
-				down(&dev->mutex);
+				mutex_lock(&dev->mutex);
 				list_for_each_entry_safe(sl, sln, &dev->slist, w1_slave_entry) {
 					if (sl->family->fid == W1_FAMILY_DEFAULT) {
 						struct w1_reg_num rn;
@@ -768,7 +850,7 @@ static int w1_control(void *data)
 				}
 				dev_dbg(&dev->dev, "Reconnecting slaves in device %s has been finished.\n", dev->name);
 				clear_bit(W1_MASTER_NEED_RECONNECT, &dev->flags);
-				up(&dev->mutex);
+				mutex_unlock(&dev->mutex);
 			}
 		}
 	}
@@ -776,10 +858,31 @@ static int w1_control(void *data)
 	return 0;
 }
 
+void w1_search_process(struct w1_master *dev, u8 search_type)
+{
+	struct w1_slave *sl, *sln;
+
+	list_for_each_entry(sl, &dev->slist, w1_slave_entry)
+		clear_bit(W1_SLAVE_ACTIVE, (long *)&sl->flags);
+
+	w1_search_devices(dev, search_type, w1_slave_found);
+
+	list_for_each_entry_safe(sl, sln, &dev->slist, w1_slave_entry) {
+		if (!test_bit(W1_SLAVE_ACTIVE, (unsigned long *)&sl->flags) && !--sl->ttl) {
+			w1_slave_detach(sl);
+
+			dev->slave_count--;
+		} else if (test_bit(W1_SLAVE_ACTIVE, (unsigned long *)&sl->flags))
+			sl->ttl = dev->slave_ttl;
+	}
+
+	if (dev->search_count > 0)
+		dev->search_count--;
+}
+
 int w1_process(void *data)
 {
 	struct w1_master *dev = (struct w1_master *) data;
-	struct w1_slave *sl, *sln;
 
 	while (!kthread_should_stop() && !test_bit(W1_MASTER_NEED_EXIT, &dev->flags)) {
 		try_to_freeze();
@@ -794,27 +897,9 @@ int w1_process(void *data)
 		if (dev->search_count == 0)
 			continue;
 
-		if (down_interruptible(&dev->mutex))
-			continue;
-
-		list_for_each_entry(sl, &dev->slist, w1_slave_entry)
-			clear_bit(W1_SLAVE_ACTIVE, (long *)&sl->flags);
-
-		w1_search_devices(dev, w1_slave_found);
-
-		list_for_each_entry_safe(sl, sln, &dev->slist, w1_slave_entry) {
-			if (!test_bit(W1_SLAVE_ACTIVE, (unsigned long *)&sl->flags) && !--sl->ttl) {
-				w1_slave_detach(sl);
-
-				dev->slave_count--;
-			} else if (test_bit(W1_SLAVE_ACTIVE, (unsigned long *)&sl->flags))
-				sl->ttl = dev->slave_ttl;
-		}
-
-		if (dev->search_count > 0)
-			dev->search_count--;
-
-		up(&dev->mutex);
+		mutex_lock(&dev->mutex);
+		w1_search_process(dev, W1_SEARCH);
+		mutex_unlock(&dev->mutex);
 	}
 
 	atomic_dec(&dev->refcnt);
@@ -828,6 +913,8 @@ static int w1_init(void)
 
 	printk(KERN_INFO "Driver for 1-wire Dallas network protocol.\n");
 
+	w1_init_netlink();
+
 	retval = bus_register(&w1_bus_type);
 	if (retval) {
 		printk(KERN_ERR "Failed to register bus. err=%d.\n", retval);
@@ -880,6 +967,8 @@ static void w1_fini(void)
 	list_for_each_entry(dev, &w1_masters, w1_master_entry)
 		__w1_remove_master_device(dev);
 
+	w1_fini_netlink();
+
 	kthread_stop(w1_control_thread);
 
 	driver_unregister(&w1_slave_driver);

drivers/w1/w1.h

@@ -41,10 +41,7 @@ struct w1_reg_num
 
 #include <linux/completion.h>
 #include <linux/device.h>
-
-#include <net/sock.h>
-
-#include <asm/semaphore.h>
+#include <linux/mutex.h>
 
 #include "w1_family.h"
 
@@ -52,7 +49,7 @@ struct w1_reg_num
 #define W1_SLAVE_DATA_SIZE	128
 
 #define W1_SEARCH		0xF0
-#define W1_CONDITIONAL_SEARCH	0xEC
+#define W1_ALARM_SEARCH		0xEC
 #define W1_CONVERT_TEMP		0x44
 #define W1_SKIP_ROM		0xCC
 #define W1_READ_SCRATCHPAD	0xBE
@@ -60,7 +57,7 @@ struct w1_reg_num
 #define W1_READ_PSUPPLY		0xB4
 #define W1_MATCH_ROM		0x55
 
-#define W1_SLAVE_ACTIVE		(1<<0)
+#define W1_SLAVE_ACTIVE		0
 
 struct w1_slave
 {
@@ -145,8 +142,8 @@ struct w1_bus_master
 	 */
 	u8		(*reset_bus)(void *);
 
-	/** Really nice hardware can handles the ROM searches */
-	void		(*search)(void *, w1_slave_found_callback);
+	/** Really nice hardware can handles the different types of ROM search */
+	void		(*search)(void *, u8, w1_slave_found_callback);
 };
 
 #define W1_MASTER_NEED_EXIT		0
@@ -173,19 +170,30 @@ struct w1_master
 	long			flags;
 
 	struct task_struct	*thread;
-	struct semaphore	mutex;
+	struct mutex		mutex;
 
 	struct device_driver	*driver;
 	struct device		dev;
 
 	struct w1_bus_master	*bus_master;
 
-	u32			seq, groups;
-	struct sock		*nls;
+	u32			seq;
 };
 
 int w1_create_master_attributes(struct w1_master *);
-void w1_search(struct w1_master *dev, w1_slave_found_callback cb);
+void w1_search(struct w1_master *dev, u8 search_type, w1_slave_found_callback cb);
+void w1_search_devices(struct w1_master *dev, u8 search_type, w1_slave_found_callback cb);
+struct w1_slave *w1_search_slave(struct w1_reg_num *id);
+void w1_search_process(struct w1_master *dev, u8 search_type);
+struct w1_master *w1_search_master_id(u32 id);
+
+u8 w1_triplet(struct w1_master *dev, int bdir);
+void w1_write_8(struct w1_master *, u8);
+int w1_reset_bus(struct w1_master *);
+u8 w1_calc_crc8(u8 *, int);
+void w1_write_block(struct w1_master *, const u8 *, int);
+u8 w1_read_block(struct w1_master *, u8 *, int);
+int w1_reset_select_slave(struct w1_slave *sl);
 
 static inline struct w1_slave* dev_to_w1_slave(struct device *dev)
 {
@@ -202,15 +210,14 @@ static inline struct w1_master* dev_to_w1_master(struct device *dev)
 	return container_of(dev, struct w1_master, dev);
 }
 
+extern struct device_driver w1_master_driver;
+extern struct device w1_master_device;
 extern int w1_max_slave_count;
 extern int w1_max_slave_ttl;
-extern spinlock_t w1_mlock;
 extern struct list_head w1_masters;
-extern struct device_driver w1_master_driver;
-extern struct device w1_master_device;
+extern struct mutex w1_mlock;
 
-int w1_process(void *data);
-void w1_reconnect_slaves(struct w1_family *f);
+extern int w1_process(void *);
 
 #endif /* __KERNEL__ */
 

drivers/w1/w1_family.c

@@ -107,6 +107,12 @@ struct w1_family * w1_family_registered(u8 fid)
 	return (ret) ? f : NULL;
 }
 
+static void __w1_family_put(struct w1_family *f)
+{
+	if (atomic_dec_and_test(&f->refcnt))
+		f->need_exit = 1;
+}
+
 void w1_family_put(struct w1_family *f)
 {
 	spin_lock(&w1_flock);
@@ -114,19 +120,14 @@ void w1_family_put(struct w1_family *f)
 	spin_unlock(&w1_flock);
 }
 
-void __w1_family_put(struct w1_family *f)
-{
-	if (atomic_dec_and_test(&f->refcnt))
-		f->need_exit = 1;
-}
-
+#if 0
 void w1_family_get(struct w1_family *f)
 {
 	spin_lock(&w1_flock);
 	__w1_family_get(f);
 	spin_unlock(&w1_flock);
-
 }
+#endif  /*  0  */
 
 void __w1_family_get(struct w1_family *f)
 {
@@ -135,8 +136,5 @@ void __w1_family_get(struct w1_family *f)
 	smp_mb__after_atomic_inc();
 }
 
-EXPORT_SYMBOL(w1_family_get);
-EXPORT_SYMBOL(w1_family_put);
-EXPORT_SYMBOL(w1_family_registered);
 EXPORT_SYMBOL(w1_unregister_family);
 EXPORT_SYMBOL(w1_register_family);

drivers/w1/w1_family.h

@@ -57,12 +57,11 @@ struct w1_family
 
 extern spinlock_t w1_flock;
 
-void w1_family_get(struct w1_family *);
 void w1_family_put(struct w1_family *);
 void __w1_family_get(struct w1_family *);
-void __w1_family_put(struct w1_family *);
 struct w1_family * w1_family_registered(u8);
 void w1_unregister_family(struct w1_family *);
 int w1_register_family(struct w1_family *);
+void w1_reconnect_slaves(struct w1_family *f);
 
 #endif /* __W1_FAMILY_H */

drivers/w1/w1_int.c

@@ -65,7 +65,7 @@ static struct w1_master * w1_alloc_dev(u32 id, int slave_count, int slave_ttl,
 	atomic_set(&dev->refcnt, 2);
 
 	INIT_LIST_HEAD(&dev->slist);
-	init_MUTEX(&dev->mutex);
+	mutex_init(&dev->mutex);
 
 	memcpy(&dev->dev, device, sizeof(struct device));
 	snprintf(dev->dev.bus_id, sizeof(dev->dev.bus_id),
@@ -74,16 +74,11 @@ static struct w1_master * w1_alloc_dev(u32 id, int slave_count, int slave_ttl,
 
 	dev->driver = driver;
 
-	dev->groups = 1;
 	dev->seq = 1;
-	dev_init_netlink(dev);
 
 	err = device_register(&dev->dev);
 	if (err) {
 		printk(KERN_ERR "Failed to register master device. err=%d\n", err);
-
-		dev_fini_netlink(dev);
-
 		memset(dev, 0, sizeof(struct w1_master));
 		kfree(dev);
 		dev = NULL;
@@ -131,12 +126,12 @@ int w1_add_master_device(struct w1_bus_master *master)
 
 	dev->initialized = 1;
 
-	spin_lock(&w1_mlock);
+	mutex_lock(&w1_mlock);
 	list_add(&dev->w1_master_entry, &w1_masters);
-	spin_unlock(&w1_mlock);
+	mutex_unlock(&w1_mlock);
 
+	memset(&msg, 0, sizeof(msg));
 	msg.id.mst.id = dev->id;
-	msg.id.mst.pid = dev->thread->pid;
 	msg.type = W1_MASTER_ADD;
 	w1_netlink_send(dev, &msg);
 
@@ -153,7 +148,6 @@ err_out_free_dev:
 void __w1_remove_master_device(struct w1_master *dev)
 {
 	struct w1_netlink_msg msg;
-	pid_t pid = dev->thread->pid;
 
 	set_bit(W1_MASTER_NEED_EXIT, &dev->flags);
 	kthread_stop(dev->thread);
@@ -166,8 +160,8 @@ void __w1_remove_master_device(struct w1_master *dev)
 			flush_signals(current);
 	}
 
+	memset(&msg, 0, sizeof(msg));
 	msg.id.mst.id = dev->id;
-	msg.id.mst.pid = pid;
 	msg.type = W1_MASTER_REMOVE;
 	w1_netlink_send(dev, &msg);
 

drivers/w1/w1_io.c

@@ -23,10 +23,10 @@
 
 #include <linux/delay.h>
 #include <linux/moduleparam.h>
+#include <linux/module.h>
 
 #include "w1.h"
 #include "w1_log.h"
-#include "w1_io.h"
 
 static int w1_delay_parm = 1;
 module_param_named(delay_coef, w1_delay_parm, int, 0);
@@ -50,7 +50,7 @@ static u8 w1_crc8_table[] = {
 	116, 42, 200, 150, 21, 75, 169, 247, 182, 232, 10, 84, 215, 137, 107, 53
 };
 
-void w1_delay(unsigned long tm)
+static void w1_delay(unsigned long tm)
 {
 	udelay(tm * w1_delay_parm);
 }
@@ -61,7 +61,7 @@ static u8 w1_read_bit(struct w1_master *dev);
 /**
  * Generates a write-0 or write-1 cycle and samples the level.
  */
-u8 w1_touch_bit(struct w1_master *dev, int bit)
+static u8 w1_touch_bit(struct w1_master *dev, int bit)
 {
 	if (dev->bus_master->touch_bit)
 		return dev->bus_master->touch_bit(dev->bus_master->data, bit);
@@ -108,6 +108,7 @@ void w1_write_8(struct w1_master *dev, u8 byte)
 		for (i = 0; i < 8; ++i)
 			w1_touch_bit(dev, (byte >> i) & 0x1);
 }
+EXPORT_SYMBOL_GPL(w1_write_8);
 
 
 /**
@@ -176,7 +177,7 @@ u8 w1_triplet(struct w1_master *dev, int bdir)
  * @param dev     the master device
  * @return        the byte read
  */
-u8 w1_read_8(struct w1_master * dev)
+static u8 w1_read_8(struct w1_master * dev)
 {
 	int i;
 	u8 res = 0;
@@ -208,6 +209,7 @@ void w1_write_block(struct w1_master *dev, const u8 *buf, int len)
 		for (i = 0; i < len; ++i)
 			w1_write_8(dev, buf[i]);
 }
+EXPORT_SYMBOL_GPL(w1_write_block);
 
 /**
  * Reads a series of bytes.
@@ -232,6 +234,7 @@ u8 w1_read_block(struct w1_master *dev, u8 *buf, int len)
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(w1_read_block);
 
 /**
  * Issues a reset bus sequence.
@@ -257,6 +260,7 @@ int w1_reset_bus(struct w1_master *dev)
 
 	return result;
 }
+EXPORT_SYMBOL_GPL(w1_reset_bus);
 
 u8 w1_calc_crc8(u8 * data, int len)
 {
@@ -267,14 +271,15 @@ u8 w1_calc_crc8(u8 * data, int len)
 
 	return crc;
 }
+EXPORT_SYMBOL_GPL(w1_calc_crc8);
 
-void w1_search_devices(struct w1_master *dev, w1_slave_found_callback cb)
+void w1_search_devices(struct w1_master *dev, u8 search_type, w1_slave_found_callback cb)
 {
 	dev->attempts++;
 	if (dev->bus_master->search)
-		dev->bus_master->search(dev->bus_master->data, cb);
+		dev->bus_master->search(dev->bus_master->data, search_type, cb);
 	else
-		w1_search(dev, cb);
+		w1_search(dev, search_type, cb);
 }
 
 /**
@@ -299,14 +304,4 @@ int w1_reset_select_slave(struct w1_slave *sl)
 	}
 	return 0;
 }
-
-EXPORT_SYMBOL(w1_touch_bit);
-EXPORT_SYMBOL(w1_write_8);
-EXPORT_SYMBOL(w1_read_8);
-EXPORT_SYMBOL(w1_reset_bus);
-EXPORT_SYMBOL(w1_calc_crc8);
-EXPORT_SYMBOL(w1_delay);
-EXPORT_SYMBOL(w1_read_block);
-EXPORT_SYMBOL(w1_write_block);
-EXPORT_SYMBOL(w1_search_devices);
-EXPORT_SYMBOL(w1_reset_select_slave);
+EXPORT_SYMBOL_GPL(w1_reset_select_slave);

drivers/w1/w1_io.h

@@ -24,11 +24,8 @@
 
 #include "w1.h"
 
-void w1_delay(unsigned long);
-u8 w1_touch_bit(struct w1_master *, int);
 u8 w1_triplet(struct w1_master *dev, int bdir);
 void w1_write_8(struct w1_master *, u8);
-u8 w1_read_8(struct w1_master *);
 int w1_reset_bus(struct w1_master *);
 u8 w1_calc_crc8(u8 *, int);
 void w1_write_block(struct w1_master *, const u8 *, int);

drivers/w1/w1_netlink.c

@@ -21,72 +21,225 @@
 
 #include <linux/skbuff.h>
 #include <linux/netlink.h>
+#include <linux/connector.h>
 
 #include "w1.h"
 #include "w1_log.h"
 #include "w1_netlink.h"
 
-#ifndef NETLINK_DISABLED
+#if defined(CONFIG_W1_CON) && (defined(CONFIG_CONNECTOR) || (defined(CONFIG_CONNECTOR_MODULE) && defined(CONFIG_W1_MODULE)))
 void w1_netlink_send(struct w1_master *dev, struct w1_netlink_msg *msg)
 {
-	unsigned int size;
-	struct sk_buff *skb;
-	struct w1_netlink_msg *data;
-	struct nlmsghdr *nlh;
+	char buf[sizeof(struct cn_msg) + sizeof(struct w1_netlink_msg)];
+	struct cn_msg *m = (struct cn_msg *)buf;
+	struct w1_netlink_msg *w = (struct w1_netlink_msg *)(m+1);
 
-	if (!dev->nls)
-		return;
+	memset(buf, 0, sizeof(buf));
 
-	size = NLMSG_SPACE(sizeof(struct w1_netlink_msg));
+	m->id.idx = CN_W1_IDX;
+	m->id.val = CN_W1_VAL;
 
-	skb = alloc_skb(size, GFP_ATOMIC);
-	if (!skb) {
-		dev_err(&dev->dev, "skb_alloc() failed.\n");
-		return;
-	}
+	m->seq = dev->seq++;
+	m->len = sizeof(struct w1_netlink_msg);
+
+	memcpy(w, msg, sizeof(struct w1_netlink_msg));
+
+	cn_netlink_send(m, 0, GFP_KERNEL);
+}
+
+static int w1_process_command_master(struct w1_master *dev, struct cn_msg *msg,
+		struct w1_netlink_msg *hdr, struct w1_netlink_cmd *cmd)
+{
+	dev_dbg(&dev->dev, "%s: %s: cmd=%02x, len=%u.\n",
+		__func__, dev->name, cmd->cmd, cmd->len);
+
+	if (cmd->cmd != W1_CMD_SEARCH && cmd->cmd != W1_CMD_ALARM_SEARCH)
+		return -EINVAL;
+
+	w1_search_process(dev, (cmd->cmd == W1_CMD_ALARM_SEARCH)?W1_ALARM_SEARCH:W1_SEARCH);
+	return 0;
+}
+
+static int w1_send_read_reply(struct w1_slave *sl, struct cn_msg *msg,
+		struct w1_netlink_msg *hdr, struct w1_netlink_cmd *cmd)
+{
+	void *data;
+	struct w1_netlink_msg *h;
+	struct w1_netlink_cmd *c;
+	struct cn_msg *cm;
+	int err;
+
+	data = kzalloc(sizeof(struct cn_msg) +
+			sizeof(struct w1_netlink_msg) +
+			sizeof(struct w1_netlink_cmd) +
+			cmd->len, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	cm = (struct cn_msg *)(data);
+	h = (struct w1_netlink_msg *)(cm + 1);
+	c = (struct w1_netlink_cmd *)(h + 1);
+
+	memcpy(cm, msg, sizeof(struct cn_msg));
+	memcpy(h, hdr, sizeof(struct w1_netlink_msg));
+	memcpy(c, cmd, sizeof(struct w1_netlink_cmd));
 
-	nlh = NLMSG_PUT(skb, 0, dev->seq++, NLMSG_DONE, size - sizeof(*nlh));
+	cm->ack = msg->seq+1;
+	cm->len = sizeof(struct w1_netlink_msg) + sizeof(struct w1_netlink_cmd) + cmd->len;
 
-	data = (struct w1_netlink_msg *)NLMSG_DATA(nlh);
+	h->len = sizeof(struct w1_netlink_cmd) + cmd->len;
 
-	memcpy(data, msg, sizeof(struct w1_netlink_msg));
+	memcpy(c->data, cmd->data, c->len);
 
-	NETLINK_CB(skb).dst_group = dev->groups;
-	netlink_broadcast(dev->nls, skb, 0, dev->groups, GFP_ATOMIC);
+	err = cn_netlink_send(cm, 0, GFP_KERNEL);
 
-nlmsg_failure:
-	return;
+	kfree(data);
+
+	return err;
 }
 
-int dev_init_netlink(struct w1_master *dev)
+static int w1_process_command_slave(struct w1_slave *sl, struct cn_msg *msg,
+		struct w1_netlink_msg *hdr, struct w1_netlink_cmd *cmd)
 {
-	dev->nls = netlink_kernel_create(NETLINK_W1, 1, NULL, THIS_MODULE);
-	if (!dev->nls) {
-		printk(KERN_ERR "Failed to create new netlink socket(%u) for w1 master %s.\n",
-			NETLINK_W1, dev->dev.bus_id);
+	int err = 0;
+
+	dev_dbg(&sl->master->dev, "%s: %02x.%012llx.%02x: cmd=%02x, len=%u.\n",
+		__func__, sl->reg_num.family, (unsigned long long)sl->reg_num.id, sl->reg_num.crc,
+		cmd->cmd, cmd->len);
+
+	switch (cmd->cmd) {
+		case W1_CMD_READ:
+			w1_read_block(sl->master, cmd->data, cmd->len);
+			w1_send_read_reply(sl, msg, hdr, cmd);
+			break;
+		case W1_CMD_WRITE:
+			w1_write_block(sl->master, cmd->data, cmd->len);
+			break;
+		case W1_CMD_SEARCH:
+		case W1_CMD_ALARM_SEARCH:
+			w1_search_process(sl->master,
+					(cmd->cmd == W1_CMD_ALARM_SEARCH)?W1_ALARM_SEARCH:W1_SEARCH);
+			break;
+		default:
+			err = -1;
+			break;
 	}
 
-	return 0;
+	return err;
 }
 
-void dev_fini_netlink(struct w1_master *dev)
+static void w1_cn_callback(void *data)
 {
-	if (dev->nls && dev->nls->sk_socket)
-		sock_release(dev->nls->sk_socket);
+	struct cn_msg *msg = data;
+	struct w1_netlink_msg *m = (struct w1_netlink_msg *)(msg + 1);
+	struct w1_netlink_cmd *cmd;
+	struct w1_slave *sl;
+	struct w1_master *dev;
+	int err = 0;
+
+	while (msg->len && !err) {
+		struct w1_reg_num id;
+		u16 mlen = m->len;
+		u8 *cmd_data = m->data;
+
+		dev = NULL;
+		sl = NULL;
+
+		memcpy(&id, m->id.id, sizeof(id));
+#if 0
+		printk("%s: %02x.%012llx.%02x: type=%02x, len=%u.\n",
+				__func__, id.family, (unsigned long long)id.id, id.crc, m->type, m->len);
+#endif
+		if (m->len + sizeof(struct w1_netlink_msg) > msg->len) {
+			err = -E2BIG;
+			break;
+		}
+
+		if (!mlen)
+			goto out_cont;
+
+		if (m->type == W1_MASTER_CMD) {
+			dev = w1_search_master_id(m->id.mst.id);
+		} else if (m->type == W1_SLAVE_CMD) {
+			sl = w1_search_slave(&id);
+			if (sl)
+				dev = sl->master;
+		}
+
+		if (!dev) {
+			err = -ENODEV;
+			goto out_cont;
+		}
+
+		mutex_lock(&dev->mutex);
+
+		if (sl && w1_reset_select_slave(sl)) {
+			err = -ENODEV;
+			goto out_up;
+		}
+
+		while (mlen) {
+			cmd = (struct w1_netlink_cmd *)cmd_data;
+
+			if (cmd->len + sizeof(struct w1_netlink_cmd) > mlen) {
+				err = -E2BIG;
+				break;
+			}
+
+			if (sl)
+				w1_process_command_slave(sl, msg, m, cmd);
+			else
+				w1_process_command_master(dev, msg, m, cmd);
+
+			cmd_data += cmd->len + sizeof(struct w1_netlink_cmd);
+			mlen -= cmd->len + sizeof(struct w1_netlink_cmd);
+		}
+out_up:
+		atomic_dec(&dev->refcnt);
+		if (sl)
+			atomic_dec(&sl->refcnt);
+		mutex_unlock(&dev->mutex);
+out_cont:
+		msg->len -= sizeof(struct w1_netlink_msg) + m->len;
+		m = (struct w1_netlink_msg *)(((u8 *)m) + sizeof(struct w1_netlink_msg) + m->len);
+
+		/*
+		 * Let's allow requests for nonexisting devices.
+		 */
+		if (err == -ENODEV)
+			err = 0;
+	}
+#if 0
+	if (err) {
+		printk("%s: malformed message. Dropping.\n", __func__);
+	}
+#endif
 }
-#else
-#warning Netlink support is disabled. Please compile with NET support enabled.
 
+int w1_init_netlink(void)
+{
+	struct cb_id w1_id = {.idx = CN_W1_IDX, .val = CN_W1_VAL};
+
+	return cn_add_callback(&w1_id, "w1", &w1_cn_callback);
+}
+
+void w1_fini_netlink(void)
+{
+	struct cb_id w1_id = {.idx = CN_W1_IDX, .val = CN_W1_VAL};
+
+	cn_del_callback(&w1_id);
+}
+#else
 void w1_netlink_send(struct w1_master *dev, struct w1_netlink_msg *msg)
 {
 }
 
-int dev_init_netlink(struct w1_master *dev)
+int w1_init_netlink(void)
 {
 	return 0;
 }
 
-void dev_fini_netlink(struct w1_master *dev)
+void w1_fini_netlink(void)
 {
 }
 #endif

drivers/w1/w1_netlink.h

@@ -23,6 +23,7 @@
 #define __W1_NETLINK_H
 
 #include <asm/types.h>
+#include <linux/connector.h>
 
 #include "w1.h"
 
@@ -31,29 +32,43 @@ enum w1_netlink_message_types {
 	W1_SLAVE_REMOVE,
 	W1_MASTER_ADD,
 	W1_MASTER_REMOVE,
+	W1_MASTER_CMD,
+	W1_SLAVE_CMD,
 };
 
 struct w1_netlink_msg
 {
 	__u8				type;
-	__u8				reserved[3];
-	union
-	{
-		struct w1_reg_num	id;
-		__u64			w1_id;
-		struct
-		{
+	__u8				reserved;
+	__u16				len;
+	union {
+		__u8			id[8];
+		struct w1_mst {
 			__u32		id;
-			__u32		pid;
+			__u32		res;
 		} mst;
 	} id;
+	__u8				data[0];
+};
+
+#define W1_CMD_READ		0x0
+#define W1_CMD_WRITE		0x1
+#define W1_CMD_SEARCH		0x2
+#define W1_CMD_ALARM_SEARCH	0x3
+
+struct w1_netlink_cmd
+{
+	__u8				cmd;
+	__u8				res;
+	__u16				len;
+	__u8				data[0];
 };
 
 #ifdef __KERNEL__
 
 void w1_netlink_send(struct w1_master *, struct w1_netlink_msg *);
-int dev_init_netlink(struct w1_master *dev);
-void dev_fini_netlink(struct w1_master *dev);
+int w1_init_netlink(void);
+void w1_fini_netlink(void);
 
 #endif /* __KERNEL__ */
 #endif /* __W1_NETLINK_H */

include/linux/connector.h

@@ -34,8 +34,11 @@
 #define CN_VAL_PROC			0x1
 #define CN_IDX_CIFS			0x2
 #define CN_VAL_CIFS                     0x1
+#define CN_W1_IDX			0x3	/* w1 communication */
+#define CN_W1_VAL			0x1
 
-#define CN_NETLINK_USERS		1
+
+#define CN_NETLINK_USERS		4
 
 /*
  * Maximum connector's message size.

include/linux/netlink.h

@@ -5,7 +5,7 @@
 #include <linux/types.h>
 
 #define NETLINK_ROUTE		0	/* Routing/device hook				*/
-#define NETLINK_W1		1	/* 1-wire subsystem				*/
+#define NETLINK_UNUSED		1	/* Unused number				*/
 #define NETLINK_USERSOCK	2	/* Reserved for user mode socket protocols 	*/
 #define NETLINK_FIREWALL	3	/* Firewalling hook				*/
 #define NETLINK_INET_DIAG	4	/* INET socket monitoring			*/