Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
  [POWERPC] Add memchr() to the bootwrapper
  [POWERPC] Implement logging of unhandled signals
  [POWERPC] Add legacy serial support for OPB with flattened device tree
  [POWERPC] Use 1TB segments
  [POWERPC] XilinxFB: Allow fixed framebuffer base address
  [POWERPC] XilinxFB: Add support for custom screen resolution
  [POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
  [POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
  [POWERPC] 4xx: Kilauea defconfig file
  [POWERPC] 4xx: Kilauea DTS
  [POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
  [POWERPC] 4xx: Add AMCC 405EX support to cputable.c
  [POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
  [POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
  [POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
  [POWERPC] 85xx: Killed <asm/mpc85xx.h>
  [POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
  [POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
  [POWERPC] mpc8272ads: Remove muram from the CPM reg property.
  [POWERPC] Make clockevents work on PPC601 processors
  ...

Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.

Documentation/powerpc/booting-without-of.txt

@@ -50,7 +50,7 @@ Table of Contents
       g) Freescale SOC SEC Security Engines
       h) Board Control and Status (BCSR)
       i) Freescale QUICC Engine module (QE)
-      j) Flash chip nodes
+      j) CFI or JEDEC memory-mapped NOR flash
       k) Global Utilities Block
 
   VII - Specifying interrupt information for devices
@@ -1510,7 +1510,10 @@ platforms are moved over to use the flattened-device-tree model.
 
    i) Freescale QUICC Engine module (QE)
    This represents qe module that is installed on PowerQUICC II Pro.
-   Hopefully it will merge backward compatibility with CPM/CPM2.
+
+   NOTE:  This is an interim binding; it should be updated to fit
+   in with the CPM binding later in this document.
+
    Basically, it is a bus of devices, that could act more or less
    as a complete entity (UCC, USB etc ). All of them should be siblings on
    the "root" qe node, using the common properties from there.
@@ -1548,7 +1551,7 @@ platforms are moved over to use the flattened-device-tree model.
    Required properties:
    - device_type : should be "spi".
    - compatible : should be "fsl_spi".
-   - mode : the SPI operation mode, it can be "cpu" or "qe".
+   - mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
    - reg : Offset and length of the register set for the device
    - interrupts : <a b> where a is the interrupt number and b is a
      field that represents an encoding of the sense and level
@@ -1757,45 +1760,69 @@ platforms are moved over to use the flattened-device-tree model.
 		};
 	};
 
-    j) Flash chip nodes
+   j) CFI or JEDEC memory-mapped NOR flash
 
     Flash chips (Memory Technology Devices) are often used for solid state
     file systems on embedded devices.
 
-    Required properties:
-
-     - device_type : has to be "rom"
-     - compatible : Should specify what this flash device is compatible with.
-       Currently, this is most likely to be "direct-mapped" (which
-       corresponds to the MTD physmap mapping driver).
-     - reg : Offset and length of the register set (or memory mapping) for
-       the device.
-     - bank-width : Width of the flash data bus in bytes. Required
-       for the NOR flashes (compatible == "direct-mapped" and others) ONLY.
-
-    Recommended properties :
-
-     - partitions : Several pairs of 32-bit values where the first value is
-       partition's offset from the start of the device and the second one is
-       partition size in bytes with LSB used to signify a read only
-       partition (so, the partition size should always be an even number).
-     - partition-names : The list of concatenated zero terminated strings
-       representing the partition names.
-     - probe-type : The type of probe which should be done for the chip
-       (JEDEC vs CFI actually). Valid ONLY for NOR flashes.
+     - compatible : should contain the specific model of flash chip(s)
+       used, if known, followed by either "cfi-flash" or "jedec-flash"
+     - reg : Address range of the flash chip
+     - bank-width : Width (in bytes) of the flash bank.  Equal to the
+       device width times the number of interleaved chips.
+     - device-width : (optional) Width of a single flash chip.  If
+       omitted, assumed to be equal to 'bank-width'.
+     - #address-cells, #size-cells : Must be present if the flash has
+       sub-nodes representing partitions (see below).  In this case
+       both #address-cells and #size-cells must be equal to 1.
+
+    For JEDEC compatible devices, the following additional properties
+    are defined:
+
+     - vendor-id : Contains the flash chip's vendor id (1 byte).
+     - device-id : Contains the flash chip's device id (1 byte).
+
+    In addition to the information on the flash bank itself, the
+    device tree may optionally contain additional information
+    describing partitions of the flash address space.  This can be
+    used on platforms which have strong conventions about which
+    portions of the flash are used for what purposes, but which don't
+    use an on-flash partition table such as RedBoot.
+
+    Each partition is represented as a sub-node of the flash device.
+    Each node's name represents the name of the corresponding
+    partition of the flash device.
+
+    Flash partitions
+     - reg : The partition's offset and size within the flash bank.
+     - label : (optional) The label / name for this flash partition.
+       If omitted, the label is taken from the node name (excluding
+       the unit address).
+     - read-only : (optional) This parameter, if present, is a hint to
+       Linux that this flash partition should only be mounted
+       read-only.  This is usually used for flash partitions
+       containing early-boot firmware images or data which should not
+       be clobbered.
 
-   Example:
+    Example:
 
- 	flash@ff000000 {
- 		device_type = "rom";
- 		compatible = "direct-mapped";
- 		probe-type = "CFI";
- 		reg = <ff000000 01000000>;
- 		bank-width = <4>;
- 		partitions = <00000000 00f80000
- 			      00f80000 00080001>;
- 		partition-names = "fs\0firmware";
- 	};
+	flash@ff000000 {
+		compatible = "amd,am29lv128ml", "cfi-flash";
+		reg = <ff000000 01000000>;
+		bank-width = <4>;
+		device-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		fs@0 {
+			label = "fs";
+			reg = <0 f80000>;
+		};
+		firmware@f80000 {
+			label ="firmware";
+			reg = <f80000 80000>;
+			read-only;
+		};
+	};
 
    k) Global Utilities Block
 
@@ -1824,8 +1851,243 @@ platforms are moved over to use the flattened-device-tree model.
 		fsl,has-rstcr;
 	};
 
+   l) Freescale Communications Processor Module
+
+   NOTE: This is an interim binding, and will likely change slightly,
+   as more devices are supported.  The QE bindings especially are
+   incomplete.
+
+   i) Root CPM node
+
+   Properties:
+   - compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
+   - reg : A 48-byte region beginning with CPCR.
+
+   Example:
+	cpm@119c0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		#interrupt-cells = <2>;
+		compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
+		reg = <119c0 30>;
+	}
+
+   ii) Properties common to mulitple CPM/QE devices
+
+   - fsl,cpm-command : This value is ORed with the opcode and command flag
+                       to specify the device on which a CPM command operates.
+
+   - fsl,cpm-brg : Indicates which baud rate generator the device
+                   is associated with.  If absent, an unused BRG
+                   should be dynamically allocated.  If zero, the
+                   device uses an external clock rather than a BRG.
+
+   - reg : Unless otherwise specified, the first resource represents the
+           scc/fcc/ucc registers, and the second represents the device's
+           parameter RAM region (if it has one).
+
+   iii) Serial
+
+   Currently defined compatibles:
+   - fsl,cpm1-smc-uart
+   - fsl,cpm2-smc-uart
+   - fsl,cpm1-scc-uart
+   - fsl,cpm2-scc-uart
+   - fsl,qe-uart
+
+   Example:
+
+	serial@11a00 {
+		device_type = "serial";
+		compatible = "fsl,mpc8272-scc-uart",
+		             "fsl,cpm2-scc-uart";
+		reg = <11a00 20 8000 100>;
+		interrupts = <28 8>;
+		interrupt-parent = <&PIC>;
+		fsl,cpm-brg = <1>;
+		fsl,cpm-command = <00800000>;
+	};
+
+   iii) Network
+
+   Currently defined compatibles:
+   - fsl,cpm1-scc-enet
+   - fsl,cpm2-scc-enet
+   - fsl,cpm1-fec-enet
+   - fsl,cpm2-fcc-enet (third resource is GFEMR)
+   - fsl,qe-enet
+
+   Example:
+
+	ethernet@11300 {
+		device_type = "network";
+		compatible = "fsl,mpc8272-fcc-enet",
+		             "fsl,cpm2-fcc-enet";
+		reg = <11300 20 8400 100 11390 1>;
+		local-mac-address = [ 00 00 00 00 00 00 ];
+		interrupts = <20 8>;
+		interrupt-parent = <&PIC>;
+		phy-handle = <&PHY0>;
+		linux,network-index = <0>;
+		fsl,cpm-command = <12000300>;
+	};
+
+   iv) MDIO
+
+   Currently defined compatibles:
+   fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
+   fsl,cpm2-mdio-bitbang (reg is port C registers)
+
+   Properties for fsl,cpm2-mdio-bitbang:
+   fsl,mdio-pin : pin of port C controlling mdio data
+   fsl,mdc-pin : pin of port C controlling mdio clock
+
+   Example:
+
+	mdio@10d40 {
+		device_type = "mdio";
+		compatible = "fsl,mpc8272ads-mdio-bitbang",
+		             "fsl,mpc8272-mdio-bitbang",
+		             "fsl,cpm2-mdio-bitbang";
+		reg = <10d40 14>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		fsl,mdio-pin = <12>;
+		fsl,mdc-pin = <13>;
+	};
+
+   v) Baud Rate Generators
+
+   Currently defined compatibles:
+   fsl,cpm-brg
+   fsl,cpm1-brg
+   fsl,cpm2-brg
+
+   Properties:
+   - reg : There may be an arbitrary number of reg resources; BRG
+     numbers are assigned to these in order.
+   - clock-frequency : Specifies the base frequency driving
+     the BRG.
+
+   Example:
+
+	brg@119f0 {
+		compatible = "fsl,mpc8272-brg",
+		             "fsl,cpm2-brg",
+		             "fsl,cpm-brg";
+		reg = <119f0 10 115f0 10>;
+		clock-frequency = <d#25000000>;
+	};
+
+   vi) Interrupt Controllers
+
+   Currently defined compatibles:
+   - fsl,cpm1-pic
+     - only one interrupt cell
+   - fsl,pq1-pic
+   - fsl,cpm2-pic
+     - second interrupt cell is level/sense:
+       - 2 is falling edge
+       - 8 is active low
+
+   Example:
+
+	interrupt-controller@10c00 {
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <10c00 80>;
+		compatible = "mpc8272-pic", "fsl,cpm2-pic";
+	};
+
+   vii) USB (Universal Serial Bus Controller)
+
+   Properties:
+   - compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
+
+   Example:
+	usb@11bc0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,cpm2-usb";
+		reg = <11b60 18 8b00 100>;
+		interrupts = <b 8>;
+		interrupt-parent = <&PIC>;
+		fsl,cpm-command = <2e600000>;
+	};
+
+   viii) Multi-User RAM (MURAM)
+
+   The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
+
+   Ranges must be set up subject to the following restrictions:
+
+   - Children's reg nodes must be offsets from the start of all muram, even
+     if the user-data area does not begin at zero.
+   - If multiple range entries are used, the difference between the parent
+     address and the child address must be the same in all, so that a single
+     mapping can cover them all while maintaining the ability to determine
+     CPM-side offsets with pointer subtraction.  It is recommended that
+     multiple range entries not be used.
+   - A child address of zero must be translatable, even if no reg resources
+     contain it.
+
+   A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
+   indicate the portion of muram that is usable by the OS for arbitrary
+   purposes.  The data node may have an arbitrary number of reg resources,
+   all of which contribute to the allocatable muram pool.
+
+   Example, based on mpc8272:
+
+	muram@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 10000>;
+
+		data@0 {
+			compatible = "fsl,cpm-muram-data";
+			reg = <0 2000 9800 800>;
+		};
+	};
+
+   m) Chipselect/Local Bus
+
+   Properties:
+   - name : Should be localbus
+   - #address-cells : Should be either two or three.  The first cell is the
+                      chipselect number, and the remaining cells are the
+                      offset into the chipselect.
+   - #size-cells : Either one or two, depending on how large each chipselect
+                   can be.
+   - ranges : Each range corresponds to a single chipselect, and cover
+              the entire access window as configured.
+
+   Example:
+	localbus@f0010100 {
+		compatible = "fsl,mpc8272ads-localbus",
+		             "fsl,mpc8272-localbus",
+		             "fsl,pq2-localbus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <f0010100 40>;
+
+		ranges = <0 0 fe000000 02000000
+		          1 0 f4500000 00008000>;
+
+		flash@0,0 {
+			compatible = "jedec-flash";
+			reg = <0 0 2000000>;
+			bank-width = <4>;
+			device-width = <1>;
+		};
+
+		board-control@1,0 {
+			reg = <1 0 20>;
+			compatible = "fsl,mpc8272ads-bcsr";
+		};
+	};
+
 
-    h) 4xx/Axon EMAC ethernet nodes
+    n) 4xx/Axon EMAC ethernet nodes
 
     The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
     the Axon bridge.  To operate this needs to interact with a ths

MAINTAINERS

@@ -1535,7 +1535,7 @@ P:	Pantelis Antoniou
 M:	pantelis.antoniou@gmail.com
 P:	Vitaly Bordug
 M:	vbordug@ru.mvista.com
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
 L:	netdev@vger.kernel.org
 S:	Maintained
 
@@ -1543,14 +1543,14 @@ FREESCALE HIGHSPEED USB DEVICE DRIVER
 P:	Li Yang
 M:	leoli@freescale.com
 L:	linux-usb-devel@lists.sourceforge.net
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 FREESCALE QUICC ENGINE UCC ETHERNET DRIVER
 P:	Li Yang
 M:	leoli@freescale.com
 L:	netdev@vger.kernel.org
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 FILE LOCKING (flock() and fcntl()/lockf())
@@ -2297,38 +2297,49 @@ S:	Maintained
 LINUX FOR POWERPC EMBEDDED MPC52XX
 P:	Sylvain Munaut
 M:	tnt@246tNt.com
+P:	Grant Likely
+M:	grant.likely@secretlab.ca
 W:	http://www.246tNt.com/mpc52xx/
 W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
-L:	linuxppc-embedded@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED PPC4XX
+P:	Josh Boyer
+M:	jwboyer@linux.vnet.ibm.com
 P:	Matt Porter
 M:	mporter@kernel.crashing.org
 W:	http://www.penguinppc.org/
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
+T:	git kernel.org:/pub/scm/linux/kernel/git/jwboyer/powerpc.git
+S:	Maintained
+
+LINUX FOR POWERPC EMBEDDED XILINX VIRTEX
+P:	Grant Likely
+M:	grant.likely@secretlab.ca
+W:	http://wiki.secretlab.ca/index.php/Linux_on_Xilinx_Virtex
+L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC BOOT CODE
 P:	Tom Rini
 M:	trini@kernel.crashing.org
 W:	http://www.penguinppc.org/
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED PPC8XX
 P:	Marcelo Tosatti
 M:	marcelo@kvack.org
 W:	http://www.penguinppc.org/
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED PPC83XX AND PPC85XX
 P:	Kumar Gala
 M:	galak@kernel.crashing.org
 W:	http://www.penguinppc.org/
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC PA SEMI PWRFICIENT
@@ -2990,7 +3001,7 @@ POWERPC 4xx EMAC DRIVER
 P:	Eugene Surovegin
 M:	ebs@ebshome.net
 W:	http://kernel.ebshome.net/emac/
-L:	linuxppc-embedded@ozlabs.org
+L:	linuxppc-dev@ozlabs.org
 L:	netdev@vger.kernel.org
 S:	Maintained
 

arch/powerpc/Kconfig

@@ -14,6 +14,11 @@ config 64BIT
 	bool
 	default y if PPC64
 
+config WORD_SIZE
+	int
+	default 64 if PPC64
+	default 32 if !PPC64
+
 config PPC_MERGE
 	def_bool y
 
@@ -21,6 +26,18 @@ config MMU
 	bool
 	default y
 
+config GENERIC_CMOS_UPDATE
+	def_bool y
+
+config GENERIC_TIME
+	def_bool y
+
+config GENERIC_TIME_VSYSCALL
+	def_bool y
+
+config GENERIC_CLOCKEVENTS
+	def_bool y
+
 config GENERIC_HARDIRQS
 	bool
 	default y
@@ -156,6 +173,7 @@ config HIGHMEM
 	bool "High memory support"
 	depends on PPC32
 
+source kernel/time/Kconfig
 source kernel/Kconfig.hz
 source kernel/Kconfig.preempt
 source "fs/Kconfig.binfmt"
@@ -180,17 +198,29 @@ config MATH_EMULATION
 	  unit, which will allow programs that use floating-point
 	  instructions to run.
 
+config 8XX_MINIMAL_FPEMU
+	bool "Minimal math emulation for 8xx"
+	depends on 8xx && !MATH_EMULATION
+	help
+	  Older arch/ppc kernels still emulated a few floating point
+	  instructions such as load and store, even when full math
+	  emulation is disabled.  Say "Y" here if you want to preserve
+	  this behavior.
+
+	  It is recommended that you build a soft-float userspace instead.
+
 config IOMMU_VMERGE
-	bool "Enable IOMMU virtual merging (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && PPC64
-	default n
+	bool "Enable IOMMU virtual merging"
+	depends on PPC64
+	default y
 	help
 	  Cause IO segments sent to a device for DMA to be merged virtually
 	  by the IOMMU when they happen to have been allocated contiguously.
 	  This doesn't add pressure to the IOMMU allocator. However, some
 	  drivers don't support getting large merged segments coming back
-	  from *_map_sg(). Say Y if you know the drivers you are using are
-	  properly handling this case.
+	  from *_map_sg().
+
+	  Most drivers don't have this problem; it is safe to say Y here.
 
 config HOTPLUG_CPU
 	bool "Support for enabling/disabling CPUs"
@@ -465,7 +495,7 @@ config PCI_8260
 
 config 8260_PCI9
 	bool "Enable workaround for MPC826x erratum PCI 9"
-	depends on PCI_8260 && !ADS8272
+	depends on PCI_8260 && !8272
 	default y
 
 choice
@@ -569,7 +599,8 @@ config TASK_SIZE_BOOL
 
 config TASK_SIZE
 	hex "Size of user task space" if TASK_SIZE_BOOL
-	default "0x80000000"
+	default "0x80000000" if PPC_PREP || PPC_8xx
+	default "0xc0000000"
 
 config CONSISTENT_START_BOOL
 	bool "Set custom consistent memory pool address"
@@ -581,6 +612,7 @@ config CONSISTENT_START_BOOL
 
 config CONSISTENT_START
 	hex "Base virtual address of consistent memory pool" if CONSISTENT_START_BOOL
+	default "0xfd000000" if (NOT_COHERENT_CACHE && 8xx)
 	default "0xff100000" if NOT_COHERENT_CACHE
 
 config CONSISTENT_SIZE_BOOL
@@ -662,3 +694,7 @@ config KEYS_COMPAT
 	default y
 
 source "crypto/Kconfig"
+
+config PPC_CLOCK
+	bool
+	default n

arch/powerpc/Kconfig.debug

@@ -124,6 +124,16 @@ config IRQSTACKS
 	  for handling hard and soft interrupts.  This can help avoid
 	  overflowing the process kernel stacks.
 
+config VIRQ_DEBUG
+	bool "Expose hardware/virtual IRQ mapping via debugfs"
+	depends on DEBUG_FS && PPC_MERGE
+	help
+	  This option will show the mapping relationship between hardware irq
+	  numbers and virtual irq numbers. The mapping is exposed via debugfs
+	  in the file powerpc/virq_mapping.
+
+	  If you don't know what this means you don't need it.
+
 config BDI_SWITCH
 	bool "Include BDI-2000 user context switcher"
 	depends on DEBUG_KERNEL && PPC32
@@ -211,6 +221,15 @@ config PPC_EARLY_DEBUG_44x
 	  Select this to enable early debugging for IBM 44x chips via the
 	  inbuilt serial port.
 
+config PPC_EARLY_DEBUG_CPM
+	bool "Early serial debugging for Freescale CPM-based serial ports"
+	depends on SERIAL_CPM
+	select PIN_TLB if PPC_8xx
+	help
+	  Select this to enable early debugging for Freescale chips
+	  using a CPM-based serial port.  This assumes that the bootwrapper
+	  has run, and set up the CPM in a particular way.
+
 endchoice
 
 config PPC_EARLY_DEBUG_44x_PHYSLOW
@@ -223,4 +242,16 @@ config PPC_EARLY_DEBUG_44x_PHYSHIGH
 	depends PPC_EARLY_DEBUG_44x
 	default "0x1"
 
+config PPC_EARLY_DEBUG_CPM_ADDR
+	hex "CPM UART early debug transmit descriptor address"
+	depends on PPC_EARLY_DEBUG_CPM
+	default "0xfa202008" if PPC_EP88XC
+	default "0xf0000008" if CPM2
+	default "0xff002008" if CPM1
+	help
+	  This specifies the address of the transmit descriptor
+	  used for early debug output.  Because it is needed before
+	  platform probing is done, all platforms selected must
+	  share the same address.
+
 endmenu

arch/powerpc/Makefile

@@ -35,11 +35,14 @@ endif
 
 export CROSS32CC CROSS32AS CROSS32LD CROSS32AR CROSS32OBJCOPY
 
+ifeq ($(CROSS_COMPILE),)
 KBUILD_DEFCONFIG := $(shell uname -m)_defconfig
+else
+KBUILD_DEFCONFIG := ppc64_defconfig
+endif
 
 ifeq ($(CONFIG_PPC64),y)
 OLDARCH	:= ppc64
-SZ	:= 64
 
 new_nm := $(shell if $(NM) --help 2>&1 | grep -- '--synthetic' > /dev/null; then echo y; else echo n; fi)
 
@@ -49,22 +52,26 @@ endif
 
 else
 OLDARCH	:= ppc
-SZ	:= 32
+endif
+
+# It seems there are times we use this Makefile without
+# including the config file, but this replicates the old behaviour
+ifeq ($(CONFIG_WORD_SIZE),)
+CONFIG_WORD_SIZE := 32
 endif
 
 UTS_MACHINE := $(OLDARCH)
 
 ifeq ($(HAS_BIARCH),y)
-override AS	+= -a$(SZ)
-override LD	+= -m elf$(SZ)ppc
-override CC	+= -m$(SZ)
-override AR	:= GNUTARGET=elf$(SZ)-powerpc $(AR)
+override AS	+= -a$(CONFIG_WORD_SIZE)
+override LD	+= -m elf$(CONFIG_WORD_SIZE)ppc
+override CC	+= -m$(CONFIG_WORD_SIZE)
+override AR	:= GNUTARGET=elf$(CONFIG_WORD_SIZE)-powerpc $(AR)
 endif
 
 LDFLAGS_vmlinux	:= -Bstatic
 
-# The -Iarch/$(ARCH)/include is temporary while we are merging
-CPPFLAGS-$(CONFIG_PPC32) := -Iarch/$(ARCH) -Iarch/$(ARCH)/include
+CPPFLAGS-$(CONFIG_PPC32) := -Iarch/$(ARCH)
 AFLAGS-$(CONFIG_PPC32)	:= -Iarch/$(ARCH)
 CFLAGS-$(CONFIG_PPC64)	:= -mminimal-toc -mtraceback=none  -mcall-aixdesc
 CFLAGS-$(CONFIG_PPC32)	:= -Iarch/$(ARCH) -ffixed-r2 -mmultiple
@@ -72,11 +79,8 @@ CPPFLAGS	+= $(CPPFLAGS-y)
 AFLAGS		+= $(AFLAGS-y)
 CFLAGS		+= -msoft-float -pipe $(CFLAGS-y)
 CPP		= $(CC) -E $(CFLAGS)
-# Temporary hack until we have migrated to asm-powerpc
-LINUXINCLUDE-$(CONFIG_PPC32)	:= -Iarch/$(ARCH)/include
-LINUXINCLUDE    += $(LINUXINCLUDE-y)
 
-CHECKFLAGS	+= -m$(SZ) -D__powerpc__ -D__powerpc$(SZ)__
+CHECKFLAGS	+= -m$(CONFIG_WORD_SIZE) -D__powerpc__ -D__powerpc$(CONFIG_WORD_SIZE)__
 
 ifeq ($(CONFIG_PPC64),y)
 GCC_BROKEN_VEC	:= $(shell if [ $(call cc-version) -lt 0400 ] ; then echo "y"; fi)
@@ -96,6 +100,10 @@ else
 endif
 endif
 
+ifeq ($(CONFIG_TUNE_CELL),y)
+	CFLAGS += $(call cc-option,-mtune=cell)
+endif
+
 # No AltiVec instruction when building kernel
 CFLAGS += $(call cc-option,-mno-altivec)
 
@@ -120,10 +128,9 @@ cpu-as-$(CONFIG_E200)		+= -Wa,-me200
 AFLAGS += $(cpu-as-y)
 CFLAGS += $(cpu-as-y)
 
-head-y				:= arch/powerpc/kernel/head_32.o
-head-$(CONFIG_PPC64)		:= arch/powerpc/kernel/head_64.o
+head-y				:= arch/powerpc/kernel/head_$(CONFIG_WORD_SIZE).o
 head-$(CONFIG_8xx)		:= arch/powerpc/kernel/head_8xx.o
-head-$(CONFIG_4xx)		:= arch/powerpc/kernel/head_4xx.o
+head-$(CONFIG_40x)		:= arch/powerpc/kernel/head_40x.o
 head-$(CONFIG_44x)		:= arch/powerpc/kernel/head_44x.o
 head-$(CONFIG_FSL_BOOKE)	:= arch/powerpc/kernel/head_fsl_booke.o
 
@@ -166,25 +173,20 @@ define archhelp
   @echo '  *_defconfig     - Select default config from arch/$(ARCH)/configs'
 endef
 
-install:
+install: vdso_install
 	$(Q)$(MAKE) $(build)=$(boot) BOOTIMAGE=$(KBUILD_IMAGE) install
 
+vdso_install:
+ifeq ($(CONFIG_PPC64),y)
+	$(Q)$(MAKE) $(build)=arch/$(ARCH)/kernel/vdso64 $@
+endif
+	$(Q)$(MAKE) $(build)=arch/$(ARCH)/kernel/vdso32 $@
+
 archclean:
 	$(Q)$(MAKE) $(clean)=$(boot)
 
-archmrproper:
-	$(Q)rm -rf arch/$(ARCH)/include
-
 archprepare: checkbin
 
-ifeq ($(CONFIG_PPC32),y)
-# Temporary hack until we have migrated to asm-powerpc
-include/asm: arch/$(ARCH)/include/asm
-arch/$(ARCH)/include/asm: FORCE
-	$(Q)if [ ! -d arch/$(ARCH)/include ]; then mkdir -p arch/$(ARCH)/include; fi
-	$(Q)ln -fsn $(srctree)/include/asm-$(OLDARCH) arch/$(ARCH)/include/asm
-endif
-
 # Use the file '.tmp_gas_check' for binutils tests, as gas won't output
 # to stdout and these checks are run even on install targets.
 TOUT	:= .tmp_gas_check

arch/powerpc/boot/.gitignore

@@ -18,14 +18,15 @@ kernel-vmlinux.strip.c
 kernel-vmlinux.strip.gz
 mktree
 uImage
-cuImage
-cuImage.bin.gz
-cuImage.elf
+cuImage.*
+treeImage.*
 zImage
+zImage.bin.*
 zImage.chrp
 zImage.coff
 zImage.coff.lds
-zImage.lds
+zImage.ep*
+zImage.*lds
 zImage.miboot
 zImage.pmac
 zImage.pseries

arch/powerpc/boot/44x.c

@@ -1,85 +0,0 @@
-/*
- * Copyright 2007 David Gibson, IBM Corporation.
- *
- * Based on earlier code:
- *   Matt Porter <mporter@kernel.crashing.org>
- *   Copyright 2002-2005 MontaVista Software Inc.
- *
- *   Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
- *   Copyright (c) 2003, 2004 Zultys Technologies
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-#include <stddef.h>
-#include "types.h"
-#include "string.h"
-#include "stdio.h"
-#include "ops.h"
-#include "reg.h"
-#include "dcr.h"
-
-/* Read the 44x memory controller to get size of system memory. */
-void ibm44x_fixup_memsize(void)
-{
-	int i;
-	unsigned long memsize, bank_config;
-
-	memsize = 0;
-	for (i = 0; i < ARRAY_SIZE(sdram_bxcr); i++) {
-		mtdcr(DCRN_SDRAM0_CFGADDR, sdram_bxcr[i]);
-		bank_config = mfdcr(DCRN_SDRAM0_CFGDATA);
-
-		if (bank_config & SDRAM_CONFIG_BANK_ENABLE)
-			memsize += SDRAM_CONFIG_BANK_SIZE(bank_config);
-	}
-
-	dt_fixup_memory(0, memsize);
-}
-
-#define SPRN_DBCR0		0x134
-#define   DBCR0_RST_SYSTEM	0x30000000
-
-void ibm44x_dbcr_reset(void)
-{
-	unsigned long tmp;
-
-	asm volatile (
-		"mfspr	%0,%1\n"
-		"oris	%0,%0,%2@h\n"
-		"mtspr	%1,%0"
-		: "=&r"(tmp) : "i"(SPRN_DBCR0), "i"(DBCR0_RST_SYSTEM)
-		);
-
-}
-
-/* Read 4xx EBC bus bridge registers to get mappings of the peripheral
- * banks into the OPB address space */
-void ibm4xx_fixup_ebc_ranges(const char *ebc)
-{
-	void *devp;
-	u32 bxcr;
-	u32 ranges[EBC_NUM_BANKS*4];
-	u32 *p = ranges;
-	int i;
-
-	for (i = 0; i < EBC_NUM_BANKS; i++) {
-		mtdcr(DCRN_EBC0_CFGADDR, EBC_BXCR(i));
-		bxcr = mfdcr(DCRN_EBC0_CFGDATA);
-
-		if ((bxcr & EBC_BXCR_BU) != EBC_BXCR_BU_OFF) {
-			*p++ = i;
-			*p++ = 0;
-			*p++ = bxcr & EBC_BXCR_BAS;
-			*p++ = EBC_BXCR_BANK_SIZE(bxcr);
-		}
-	}
-
-	devp = finddevice(ebc);
-	if (! devp)
-		fatal("Couldn't locate EBC node %s\n\r", ebc);
-
-	setprop(devp, "ranges", ranges, (p - ranges) * sizeof(u32));
-}

arch/powerpc/boot/44x.h

@@ -10,10 +10,7 @@
 #ifndef _PPC_BOOT_44X_H_
 #define _PPC_BOOT_44X_H_
 
-void ibm44x_fixup_memsize(void);
-void ibm4xx_fixup_ebc_ranges(const char *ebc);
-
-void ibm44x_dbcr_reset(void);
 void ebony_init(void *mac0, void *mac1);
+void bamboo_init(void *mac0, void *mac1);
 
 #endif /* _PPC_BOOT_44X_H_ */

arch/powerpc/boot/4xx.c

@@ -0,0 +1,300 @@
+/*
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * Based on earlier code:
+ *   Matt Porter <mporter@kernel.crashing.org>
+ *   Copyright 2002-2005 MontaVista Software Inc.
+ *
+ *   Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
+ *   Copyright (c) 2003, 2004 Zultys Technologies
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <stddef.h>
+#include "types.h"
+#include "string.h"
+#include "stdio.h"
+#include "ops.h"
+#include "reg.h"
+#include "dcr.h"
+
+/* Read the 4xx SDRAM controller to get size of system memory. */
+void ibm4xx_fixup_memsize(void)
+{
+	int i;
+	unsigned long memsize, bank_config;
+
+	memsize = 0;
+	for (i = 0; i < ARRAY_SIZE(sdram_bxcr); i++) {
+		mtdcr(DCRN_SDRAM0_CFGADDR, sdram_bxcr[i]);
+		bank_config = mfdcr(DCRN_SDRAM0_CFGDATA);
+
+		if (bank_config & SDRAM_CONFIG_BANK_ENABLE)
+			memsize += SDRAM_CONFIG_BANK_SIZE(bank_config);
+	}
+
+	dt_fixup_memory(0, memsize);
+}
+
+/* 4xx DDR1/2 Denali memory controller support */
+/* DDR0 registers */
+#define DDR0_02			2
+#define DDR0_08			8
+#define DDR0_10			10
+#define DDR0_14			14
+#define DDR0_42			42
+#define DDR0_43			43
+
+/* DDR0_02 */
+#define DDR_START		0x1
+#define DDR_START_SHIFT		0
+#define DDR_MAX_CS_REG		0x3
+#define DDR_MAX_CS_REG_SHIFT	24
+#define DDR_MAX_COL_REG		0xf
+#define DDR_MAX_COL_REG_SHIFT	16
+#define DDR_MAX_ROW_REG		0xf
+#define DDR_MAX_ROW_REG_SHIFT	8
+/* DDR0_08 */
+#define DDR_DDR2_MODE		0x1
+#define DDR_DDR2_MODE_SHIFT	0
+/* DDR0_10 */
+#define DDR_CS_MAP		0x3
+#define DDR_CS_MAP_SHIFT	8
+/* DDR0_14 */
+#define DDR_REDUC		0x1
+#define DDR_REDUC_SHIFT		16
+/* DDR0_42 */
+#define DDR_APIN		0x7
+#define DDR_APIN_SHIFT		24
+/* DDR0_43 */
+#define DDR_COL_SZ		0x7
+#define DDR_COL_SZ_SHIFT	8
+#define DDR_BANK8		0x1
+#define DDR_BANK8_SHIFT		0
+
+#define DDR_GET_VAL(val, mask, shift)	(((val) >> (shift)) & (mask))
+
+static inline u32 mfdcr_sdram0(u32 reg)
+{
+        mtdcr(DCRN_SDRAM0_CFGADDR, reg);
+        return mfdcr(DCRN_SDRAM0_CFGDATA);
+}
+
+void ibm4xx_denali_fixup_memsize(void)
+{
+	u32 val, max_cs, max_col, max_row;
+	u32 cs, col, row, bank, dpath;
+	unsigned long memsize;
+
+	val = mfdcr_sdram0(DDR0_02);
+	if (!DDR_GET_VAL(val, DDR_START, DDR_START_SHIFT))
+		fatal("DDR controller is not initialized\n");
+
+	/* get maximum cs col and row values */
+	max_cs  = DDR_GET_VAL(val, DDR_MAX_CS_REG, DDR_MAX_CS_REG_SHIFT);
+	max_col = DDR_GET_VAL(val, DDR_MAX_COL_REG, DDR_MAX_COL_REG_SHIFT);
+	max_row = DDR_GET_VAL(val, DDR_MAX_ROW_REG, DDR_MAX_ROW_REG_SHIFT);
+
+	/* get CS value */
+	val = mfdcr_sdram0(DDR0_10);
+
+	val = DDR_GET_VAL(val, DDR_CS_MAP, DDR_CS_MAP_SHIFT);
+	cs = 0;
+	while (val) {
+		if (val && 0x1)
+			cs++;
+		val = val >> 1;
+	}
+
+	if (!cs)
+		fatal("No memory installed\n");
+	if (cs > max_cs)
+		fatal("DDR wrong CS configuration\n");
+
+	/* get data path bytes */
+	val = mfdcr_sdram0(DDR0_14);
+
+	if (DDR_GET_VAL(val, DDR_REDUC, DDR_REDUC_SHIFT))
+		dpath = 8; /* 64 bits */
+	else
+		dpath = 4; /* 32 bits */
+
+	/* get adress pins (rows) */
+	val = mfdcr_sdram0(DDR0_42);
+
+	row = DDR_GET_VAL(val, DDR_APIN, DDR_APIN_SHIFT);
+	if (row > max_row)
+		fatal("DDR wrong APIN configuration\n");
+	row = max_row - row;
+
+	/* get collomn size and banks */
+	val = mfdcr_sdram0(DDR0_43);
+
+	col = DDR_GET_VAL(val, DDR_COL_SZ, DDR_COL_SZ_SHIFT);
+	if (col > max_col)
+		fatal("DDR wrong COL configuration\n");
+	col = max_col - col;
+
+	if (DDR_GET_VAL(val, DDR_BANK8, DDR_BANK8_SHIFT))
+		bank = 8; /* 8 banks */
+	else
+		bank = 4; /* 4 banks */
+
+	memsize = cs * (1 << (col+row)) * bank * dpath;
+	dt_fixup_memory(0, memsize);
+}
+
+#define SPRN_DBCR0_40X 0x3F2
+#define SPRN_DBCR0_44X 0x134
+#define DBCR0_RST_SYSTEM 0x30000000
+
+void ibm44x_dbcr_reset(void)
+{
+	unsigned long tmp;
+
+	asm volatile (
+		"mfspr	%0,%1\n"
+		"oris	%0,%0,%2@h\n"
+		"mtspr	%1,%0"
+		: "=&r"(tmp) : "i"(SPRN_DBCR0_44X), "i"(DBCR0_RST_SYSTEM)
+		);
+
+}
+
+void ibm40x_dbcr_reset(void)
+{
+	unsigned long tmp;
+
+	asm volatile (
+		"mfspr	%0,%1\n"
+		"oris	%0,%0,%2@h\n"
+		"mtspr	%1,%0"
+		: "=&r"(tmp) : "i"(SPRN_DBCR0_40X), "i"(DBCR0_RST_SYSTEM)
+		);
+}
+
+#define EMAC_RESET 0x20000000
+void ibm4xx_quiesce_eth(u32 *emac0, u32 *emac1)
+{
+	/* Quiesce the MAL and EMAC(s) since PIBS/OpenBIOS don't do this for us */
+	if (emac0)
+		*emac0 = EMAC_RESET;
+	if (emac1)
+		*emac1 = EMAC_RESET;
+
+	mtdcr(DCRN_MAL0_CFG, MAL_RESET);
+}
+
+/* Read 4xx EBC bus bridge registers to get mappings of the peripheral
+ * banks into the OPB address space */
+void ibm4xx_fixup_ebc_ranges(const char *ebc)
+{
+	void *devp;
+	u32 bxcr;
+	u32 ranges[EBC_NUM_BANKS*4];
+	u32 *p = ranges;
+	int i;
+
+	for (i = 0; i < EBC_NUM_BANKS; i++) {
+		mtdcr(DCRN_EBC0_CFGADDR, EBC_BXCR(i));
+		bxcr = mfdcr(DCRN_EBC0_CFGDATA);
+
+		if ((bxcr & EBC_BXCR_BU) != EBC_BXCR_BU_OFF) {
+			*p++ = i;
+			*p++ = 0;
+			*p++ = bxcr & EBC_BXCR_BAS;
+			*p++ = EBC_BXCR_BANK_SIZE(bxcr);
+		}
+	}
+
+	devp = finddevice(ebc);
+	if (! devp)
+		fatal("Couldn't locate EBC node %s\n\r", ebc);
+
+	setprop(devp, "ranges", ranges, (p - ranges) * sizeof(u32));
+}
+
+#define SPRN_CCR1 0x378
+void ibm440ep_fixup_clocks(unsigned int sysclk, unsigned int ser_clk)
+{
+	u32 cpu, plb, opb, ebc, tb, uart0, m, vco;
+	u32 reg;
+	u32 fwdva, fwdvb, fbdv, lfbdv, opbdv0, perdv0, spcid0, prbdv0, tmp;
+
+	mtdcr(DCRN_CPR0_ADDR, CPR0_PLLD0);
+	reg = mfdcr(DCRN_CPR0_DATA);
+	tmp = (reg & 0x000F0000) >> 16;
+	fwdva = tmp ? tmp : 16;
+	tmp = (reg & 0x00000700) >> 8;
+	fwdvb = tmp ? tmp : 8;
+	tmp = (reg & 0x1F000000) >> 24;
+	fbdv = tmp ? tmp : 32;
+	lfbdv = (reg & 0x0000007F);
+
+	mtdcr(DCRN_CPR0_ADDR, CPR0_OPBD0);
+	reg = mfdcr(DCRN_CPR0_DATA);
+	tmp = (reg & 0x03000000) >> 24;
+	opbdv0 = tmp ? tmp : 4;
+
+	mtdcr(DCRN_CPR0_ADDR, CPR0_PERD0);
+	reg = mfdcr(DCRN_CPR0_DATA);
+	tmp = (reg & 0x07000000) >> 24;
+	perdv0 = tmp ? tmp : 8;
+
+	mtdcr(DCRN_CPR0_ADDR, CPR0_PRIMBD0);
+	reg = mfdcr(DCRN_CPR0_DATA);
+	tmp = (reg & 0x07000000) >> 24;
+	prbdv0 = tmp ? tmp : 8;
+
+	mtdcr(DCRN_CPR0_ADDR, CPR0_SCPID);
+	reg = mfdcr(DCRN_CPR0_DATA);
+	tmp = (reg & 0x03000000) >> 24;
+	spcid0 = tmp ? tmp : 4;
+
+	/* Calculate M */
+	mtdcr(DCRN_CPR0_ADDR, CPR0_PLLC0);
+	reg = mfdcr(DCRN_CPR0_DATA);
+	tmp = (reg & 0x03000000) >> 24;
+	if (tmp == 0) { /* PLL output */
+		tmp = (reg & 0x20000000) >> 29;
+		if (!tmp) /* PLLOUTA */
+			m = fbdv * lfbdv * fwdva;
+		else
+			m = fbdv * lfbdv * fwdvb;
+	}
+	else if (tmp == 1) /* CPU output */
+		m = fbdv * fwdva;
+	else
+		m = perdv0 * opbdv0 * fwdvb;
+
+	vco = (m * sysclk) + (m >> 1);
+	cpu = vco / fwdva;
+	plb = vco / fwdvb / prbdv0;
+	opb = plb / opbdv0;
+	ebc = plb / perdv0;
+
+	/* FIXME */
+	uart0 = ser_clk;
+
+	/* Figure out timebase.  Either CPU or default TmrClk */
+	asm volatile (
+			"mfspr	%0,%1\n"
+			:
+			"=&r"(reg) : "i"(SPRN_CCR1));
+	if (reg & 0x0080)
+		tb = 25000000; /* TmrClk is 25MHz */
+	else
+		tb = cpu;
+
+	dt_fixup_cpu_clocks(cpu, tb, 0);
+	dt_fixup_clock("/plb", plb);
+	dt_fixup_clock("/plb/opb", opb);
+	dt_fixup_clock("/plb/opb/ebc", ebc);
+	dt_fixup_clock("/plb/opb/serial@ef600300", uart0);
+	dt_fixup_clock("/plb/opb/serial@ef600400", uart0);
+	dt_fixup_clock("/plb/opb/serial@ef600500", uart0);
+	dt_fixup_clock("/plb/opb/serial@ef600600", uart0);
+}

arch/powerpc/boot/4xx.h

@@ -0,0 +1,22 @@
+/*
+ * PowerPC 4xx related functions
+ *
+ * Copyright 2007 IBM Corporation.
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#ifndef _POWERPC_BOOT_4XX_H_
+#define _POWERPC_BOOT_4XX_H_
+
+void ibm4xx_fixup_memsize(void);
+void ibm4xx_denali_fixup_memsize(void);
+void ibm44x_dbcr_reset(void);
+void ibm40x_dbcr_reset(void);
+void ibm4xx_quiesce_eth(u32 *emac0, u32 *emac1);
+void ibm4xx_fixup_ebc_ranges(const char *ebc);
+void ibm440ep_fixup_clocks(unsigned int sysclk, unsigned int ser_clk);
+
+#endif /* _POWERPC_BOOT_4XX_H_ */

arch/powerpc/boot/Makefile

@@ -25,14 +25,19 @@ BOOTCFLAGS    := -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs \
 		 -isystem $(shell $(CROSS32CC) -print-file-name=include)
 BOOTAFLAGS	:= -D__ASSEMBLY__ $(BOOTCFLAGS) -traditional -nostdinc
 
+ifdef CONFIG_DEBUG_INFO
+BOOTCFLAGS	+= -g
+endif
+
 ifeq ($(call cc-option-yn, -fstack-protector),y)
 BOOTCFLAGS	+= -fno-stack-protector
 endif
 
 BOOTCFLAGS	+= -I$(obj) -I$(srctree)/$(obj)
 
-$(obj)/44x.o: BOOTCFLAGS += -mcpu=440
+$(obj)/4xx.o: BOOTCFLAGS += -mcpu=440
 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=440
+$(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
 
 zlib       := inffast.c inflate.c inftrees.c
 zlibheader := inffast.h inffixed.h inflate.h inftrees.h infutil.h
@@ -44,10 +49,14 @@ $(addprefix $(obj)/,$(zlib) gunzip_util.o main.o): \
 src-wlib := string.S crt0.S stdio.c main.c flatdevtree.c flatdevtree_misc.c \
 		ns16550.c serial.c simple_alloc.c div64.S util.S \
 		gunzip_util.c elf_util.c $(zlib) devtree.c oflib.c ofconsole.c \
-		44x.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c
-src-plat := of.c cuboot-83xx.c cuboot-85xx.c holly.c \
+		4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c bamboo.c \
+		cpm-serial.c stdlib.c mpc52xx-psc.c planetcore.c uartlite.c \
+		fsl-soc.c mpc8xx.c pq2.c
+src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
 		cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
-		ps3-head.S ps3-hvcall.S ps3.c
+		ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
+		cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c \
+		fixed-head.S ep88xc.c cuboot-hpc2.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -139,9 +148,17 @@ image-$(CONFIG_PPC_ISERIES)		+= zImage.iseries
 image-$(CONFIG_DEFAULT_UIMAGE)		+= uImage
 
 ifneq ($(CONFIG_DEVICE_TREE),"")
+image-$(CONFIG_PPC_8xx)			+= cuImage.8xx
+image-$(CONFIG_PPC_EP88XC)		+= zImage.ep88xc
+image-$(CONFIG_8260)			+= cuImage.pq2
+image-$(CONFIG_PPC_MPC52xx)		+= cuImage.52xx
 image-$(CONFIG_PPC_83xx)		+= cuImage.83xx
 image-$(CONFIG_PPC_85xx)		+= cuImage.85xx
+image-$(CONFIG_MPC7448HPC2)		+= cuImage.hpc2
 image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
+image-$(CONFIG_BAMBOO)			+= treeImage.bamboo cuImage.bamboo
+image-$(CONFIG_SEQUOIA)			+= cuImage.sequoia
+image-$(CONFIG_WALNUT)			+= treeImage.walnut
 endif
 
 # For 32-bit powermacs, build the COFF and miboot images

arch/powerpc/boot/bamboo.c

@@ -0,0 +1,47 @@
+/*
+ * Copyright IBM Corporation, 2007
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Based on ebony wrapper:
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * Clocking code based on code by:
+ * Stefan Roese <sr@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2 of the License
+ */
+#include <stdarg.h>
+#include <stddef.h>
+#include "types.h"
+#include "elf.h"
+#include "string.h"
+#include "stdio.h"
+#include "page.h"
+#include "ops.h"
+#include "dcr.h"
+#include "4xx.h"
+#include "44x.h"
+
+static u8 *bamboo_mac0, *bamboo_mac1;
+
+static void bamboo_fixups(void)
+{
+	unsigned long sysclk = 33333333;
+
+	ibm440ep_fixup_clocks(sysclk, 11059200);
+	ibm4xx_fixup_memsize();
+	ibm4xx_quiesce_eth((u32 *)0xef600e00, (u32 *)0xef600f00);
+	dt_fixup_mac_addresses(bamboo_mac0, bamboo_mac1);
+}
+
+void bamboo_init(void *mac0, void *mac1)
+{
+	platform_ops.fixups = bamboo_fixups;
+	platform_ops.exit = ibm44x_dbcr_reset;
+	bamboo_mac0 = mac0;
+	bamboo_mac1 = mac1;
+	ft_init(_dtb_start, 0, 32);
+	serial_console_init();
+}

arch/powerpc/boot/cpm-serial.c

@@ -0,0 +1,269 @@
+/*
+ * CPM serial console support.
+ *
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * It is assumed that the firmware (or the platform file) has already set
+ * up the port.
+ */
+
+#include "types.h"
+#include "io.h"
+#include "ops.h"
+
+struct cpm_scc {
+	u32 gsmrl;
+	u32 gsmrh;
+	u16 psmr;
+	u8 res1[2];
+	u16 todr;
+	u16 dsr;
+	u16 scce;
+	u8 res2[2];
+	u16 sccm;
+	u8 res3;
+	u8 sccs;
+	u8 res4[8];
+};
+
+struct cpm_smc {
+	u8 res1[2];
+	u16 smcmr;
+	u8 res2[2];
+	u8 smce;
+	u8 res3[3];
+	u8 smcm;
+	u8 res4[5];
+};
+
+struct cpm_param {
+	u16 rbase;
+	u16 tbase;
+	u8 rfcr;
+	u8 tfcr;
+};
+
+struct cpm_bd {
+	u16 sc;   /* Status and Control */
+	u16 len;  /* Data length in buffer */
+	u8 *addr; /* Buffer address in host memory */
+};
+
+static void *cpcr;
+static struct cpm_param *param;
+static struct cpm_smc *smc;
+static struct cpm_scc *scc;
+struct cpm_bd *tbdf, *rbdf;
+static u32 cpm_cmd;
+static u8 *muram_start;
+static u32 muram_offset;
+
+static void (*do_cmd)(int op);
+static void (*enable_port)(void);
+static void (*disable_port)(void);
+
+#define CPM_CMD_STOP_TX     4
+#define CPM_CMD_RESTART_TX  6
+#define CPM_CMD_INIT_RX_TX  0
+
+static void cpm1_cmd(int op)
+{
+	while (in_be16(cpcr) & 1)
+		;
+
+	out_be16(cpcr, (op << 8) | cpm_cmd | 1);
+
+	while (in_be16(cpcr) & 1)
+		;
+}
+
+static void cpm2_cmd(int op)
+{
+	while (in_be32(cpcr) & 0x10000)
+		;
+
+	out_be32(cpcr, op | cpm_cmd | 0x10000);
+
+	while (in_be32(cpcr) & 0x10000)
+		;
+}
+
+static void smc_disable_port(void)
+{
+	do_cmd(CPM_CMD_STOP_TX);
+	out_be16(&smc->smcmr, in_be16(&smc->smcmr) & ~3);
+}
+
+static void scc_disable_port(void)
+{
+	do_cmd(CPM_CMD_STOP_TX);
+	out_be32(&scc->gsmrl, in_be32(&scc->gsmrl) & ~0x30);
+}
+
+static void smc_enable_port(void)
+{
+	out_be16(&smc->smcmr, in_be16(&smc->smcmr) | 3);
+	do_cmd(CPM_CMD_RESTART_TX);
+}
+
+static void scc_enable_port(void)
+{
+	out_be32(&scc->gsmrl, in_be32(&scc->gsmrl) | 0x30);
+	do_cmd(CPM_CMD_RESTART_TX);
+}
+
+static int cpm_serial_open(void)
+{
+	disable_port();
+
+	out_8(&param->rfcr, 0x10);
+	out_8(&param->tfcr, 0x10);
+
+	rbdf = (struct cpm_bd *)muram_start;
+	rbdf->addr = (u8 *)(rbdf + 2);
+	rbdf->sc = 0xa000;
+	rbdf->len = 1;
+
+	tbdf = rbdf + 1;
+	tbdf->addr = (u8 *)(rbdf + 2) + 1;
+	tbdf->sc = 0x2000;
+	tbdf->len = 1;
+
+	sync();
+	out_be16(&param->rbase, muram_offset);
+	out_be16(&param->tbase, muram_offset + sizeof(struct cpm_bd));
+
+	do_cmd(CPM_CMD_INIT_RX_TX);
+
+	enable_port();
+	return 0;
+}
+
+static void cpm_serial_putc(unsigned char c)
+{
+	while (tbdf->sc & 0x8000)
+		barrier();
+
+	sync();
+
+	tbdf->addr[0] = c;
+	eieio();
+	tbdf->sc |= 0x8000;
+}
+
+static unsigned char cpm_serial_tstc(void)
+{
+	barrier();
+	return !(rbdf->sc & 0x8000);
+}
+
+static unsigned char cpm_serial_getc(void)
+{
+	unsigned char c;
+
+	while (!cpm_serial_tstc())
+		;
+
+	sync();
+	c = rbdf->addr[0];
+	eieio();
+	rbdf->sc |= 0x8000;
+
+	return c;
+}
+
+int cpm_console_init(void *devp, struct serial_console_data *scdp)
+{
+	void *reg_virt[2];
+	int is_smc = 0, is_cpm2 = 0, n;
+	unsigned long reg_phys;
+	void *parent, *muram;
+
+	if (dt_is_compatible(devp, "fsl,cpm1-smc-uart")) {
+		is_smc = 1;
+	} else if (dt_is_compatible(devp, "fsl,cpm2-scc-uart")) {
+		is_cpm2 = 1;
+	} else if (dt_is_compatible(devp, "fsl,cpm2-smc-uart")) {
+		is_cpm2 = 1;
+		is_smc = 1;
+	}
+
+	if (is_smc) {
+		enable_port = smc_enable_port;
+		disable_port = smc_disable_port;
+	} else {
+		enable_port = scc_enable_port;
+		disable_port = scc_disable_port;
+	}
+
+	if (is_cpm2)
+		do_cmd = cpm2_cmd;
+	else
+		do_cmd = cpm1_cmd;
+
+	n = getprop(devp, "fsl,cpm-command", &cpm_cmd, 4);
+	if (n < 4)
+		return -1;
+
+	n = getprop(devp, "virtual-reg", reg_virt, sizeof(reg_virt));
+	if (n < (int)sizeof(reg_virt)) {
+		for (n = 0; n < 2; n++) {
+			if (!dt_xlate_reg(devp, n, &reg_phys, NULL))
+				return -1;
+
+			reg_virt[n] = (void *)reg_phys;
+		}
+	}
+
+	if (is_smc)
+		smc = reg_virt[0];
+	else
+		scc = reg_virt[0];
+
+	param = reg_virt[1];
+
+	parent = get_parent(devp);
+	if (!parent)
+		return -1;
+
+	n = getprop(parent, "virtual-reg", reg_virt, sizeof(reg_virt));
+	if (n < (int)sizeof(reg_virt)) {
+		if (!dt_xlate_reg(parent, 0, &reg_phys, NULL))
+			return -1;
+
+		reg_virt[0] = (void *)reg_phys;
+	}
+
+	cpcr = reg_virt[0];
+
+	muram = finddevice("/soc/cpm/muram/data");
+	if (!muram)
+		return -1;
+
+	/* For bootwrapper-compatible device trees, we assume that the first
+	 * entry has at least 18 bytes, and that #address-cells/#data-cells
+	 * is one for both parent and child.
+	 */
+
+	n = getprop(muram, "virtual-reg", reg_virt, sizeof(reg_virt));
+	if (n < (int)sizeof(reg_virt)) {
+		if (!dt_xlate_reg(muram, 0, &reg_phys, NULL))
+			return -1;
+
+		reg_virt[0] = (void *)reg_phys;
+	}
+
+	muram_start = reg_virt[0];
+
+	n = getprop(muram, "reg", &muram_offset, 4);
+	if (n < 4)
+		return -1;
+
+	scdp->open = cpm_serial_open;
+	scdp->putc = cpm_serial_putc;
+	scdp->getc = cpm_serial_getc;
+	scdp->tstc = cpm_serial_tstc;
+
+	return 0;
+}

arch/powerpc/boot/cuboot-52xx.c

@@ -0,0 +1,59 @@
+/*
+ * Old U-boot compatibility for MPC5200
+ *
+ * Author: Grant Likely <grant.likely@secretlab.ca>
+ *
+ * Copyright (c) 2007 Secret Lab Technologies Ltd.
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "io.h"
+#include "cuboot.h"
+
+#define TARGET_PPC_MPC52xx
+#include "ppcboot.h"
+
+static bd_t bd;
+
+static void platform_fixups(void)
+{
+	void *soc, *reg;
+	int div;
+	u32 sysfreq;
+
+
+	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+	dt_fixup_mac_addresses(bd.bi_enetaddr);
+	dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 4, bd.bi_busfreq);
+
+	/* Unfortunately, the specific model number is encoded in the
+	 * soc node name in existing dts files -- once that is fixed,
+	 * this can do a simple path lookup.
+	 */
+	soc = find_node_by_devtype(NULL, "soc");
+	if (soc) {
+		setprop(soc, "bus-frequency", &bd.bi_ipbfreq,
+			sizeof(bd.bi_ipbfreq));
+
+		if (!dt_xlate_reg(soc, 0, (void*)&reg, NULL))
+			return;
+		div = in_8(reg + 0x204) & 0x0020 ? 8 : 4;
+		sysfreq = bd.bi_busfreq * div;
+		setprop(soc, "system-frequency", &sysfreq, sizeof(sysfreq));
+	}
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+                   unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	ft_init(_dtb_start, _dtb_end - _dtb_start, 32);
+	serial_console_init();
+	platform_ops.fixups = platform_fixups;
+}

arch/powerpc/boot/cuboot-83xx.c

@@ -18,7 +18,6 @@
 #include "ppcboot.h"
 
 static bd_t bd;
-extern char _dtb_start[], _dtb_end[];
 
 static void platform_fixups(void)
 {

arch/powerpc/boot/cuboot-85xx.c

@@ -18,7 +18,6 @@
 #include "ppcboot.h"
 
 static bd_t bd;
-extern char _dtb_start[], _dtb_end[];
 
 static void platform_fixups(void)
 {

arch/powerpc/boot/cuboot-8xx.c

@@ -0,0 +1,47 @@
+/*
+ * Old U-boot compatibility for 8xx
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "cuboot.h"
+
+#define TARGET_8xx
+#define TARGET_HAS_ETH1
+#include "ppcboot.h"
+
+static bd_t bd;
+
+static void platform_fixups(void)
+{
+	void *node;
+
+	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+	dt_fixup_mac_addresses(bd.bi_enetaddr, bd.bi_enet1addr);
+	dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 16, bd.bi_busfreq);
+
+	node = finddevice("/soc/cpm");
+	if (node)
+		setprop(node, "clock-frequency", &bd.bi_busfreq, 4);
+
+	node = finddevice("/soc/cpm/brg");
+	if (node)
+		setprop(node, "clock-frequency",  &bd.bi_busfreq, 4);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+                   unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	ft_init(_dtb_start, _dtb_end - _dtb_start, 32);
+	serial_console_init();
+	platform_ops.fixups = platform_fixups;
+}

arch/powerpc/boot/cuboot-bamboo.c

@@ -0,0 +1,30 @@
+/*
+ * Old U-boot compatibility for Bamboo
+ *
+ * Author: Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Copyright 2007 IBM Corporation
+ *
+ * Based on cuboot-ebony.c
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+		unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	bamboo_init(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}

arch/powerpc/boot/cuboot-hpc2.c

@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * Author: Roy Zang <tie-fei.zang@freescale.com>
+ *
+ * Description:
+ * Old U-boot compatibility for mpc7448hpc2 board
+ * Based on the code of Scott Wood <scottwood@freescale.com>
+ * for 83xx and 85xx.
+ *
+ * This is free software; you can redistribute it and/or modify
+ * it under the terms of  the GNU General  Public License as published by
+ * the Free Software Foundation;  either version 2 of the  License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "cuboot.h"
+
+#define TARGET_HAS_ETH1
+#include "ppcboot.h"
+
+static bd_t bd;
+extern char _dtb_start[], _dtb_end[];
+
+static void platform_fixups(void)
+{
+	void *tsi;
+
+	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+	dt_fixup_mac_addresses(bd.bi_enetaddr, bd.bi_enet1addr);
+	dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 4, bd.bi_busfreq);
+	tsi = find_node_by_devtype(NULL, "tsi-bridge");
+	if (tsi)
+		setprop(tsi, "bus-frequency", &bd.bi_busfreq,
+			sizeof(bd.bi_busfreq));
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+		unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	ft_init(_dtb_start, _dtb_end - _dtb_start, 32);
+	serial_console_init();
+	platform_ops.fixups = platform_fixups;
+}

arch/powerpc/boot/cuboot-pq2.c

@@ -0,0 +1,261 @@
+/*
+ * Old U-boot compatibility for PowerQUICC II
+ * (a.k.a. 82xx with CPM, not the 8240 family of chips)
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "cuboot.h"
+#include "io.h"
+#include "fsl-soc.h"
+
+#define TARGET_CPM2
+#define TARGET_HAS_ETH1
+#include "ppcboot.h"
+
+static bd_t bd;
+
+struct cs_range {
+	u32 csnum;
+	u32 base; /* must be zero */
+	u32 addr;
+	u32 size;
+};
+
+struct pci_range {
+	u32 flags;
+	u32 pci_addr[2];
+	u32 phys_addr;
+	u32 size[2];
+};
+
+struct cs_range cs_ranges_buf[MAX_PROP_LEN / sizeof(struct cs_range)];
+struct pci_range pci_ranges_buf[MAX_PROP_LEN / sizeof(struct pci_range)];
+
+/* Different versions of u-boot put the BCSR in different places, and
+ * some don't set up the PCI PIC at all, so we assume the device tree is
+ * sane and update the BRx registers appropriately.
+ *
+ * For any node defined as compatible with fsl,pq2-localbus,
+ * #address/#size must be 2/1 for the localbus, and 1/1 for the parent bus.
+ * Ranges must be for whole chip selects.
+ */
+static void update_cs_ranges(void)
+{
+	void *bus_node, *parent_node;
+	u32 *ctrl_addr;
+	unsigned long ctrl_size;
+	u32 naddr, nsize;
+	int len;
+	int i;
+
+	bus_node = finddevice("/localbus");
+	if (!bus_node || !dt_is_compatible(bus_node, "fsl,pq2-localbus"))
+		return;
+
+	dt_get_reg_format(bus_node, &naddr, &nsize);
+	if (naddr != 2 || nsize != 1)
+		goto err;
+
+	parent_node = get_parent(bus_node);
+	if (!parent_node)
+		goto err;
+
+	dt_get_reg_format(parent_node, &naddr, &nsize);
+	if (naddr != 1 || nsize != 1)
+		goto err;
+
+	if (!dt_xlate_reg(bus_node, 0, (unsigned long *)&ctrl_addr,
+	                  &ctrl_size))
+		goto err;
+
+	len = getprop(bus_node, "ranges", cs_ranges_buf, sizeof(cs_ranges_buf));
+
+	for (i = 0; i < len / sizeof(struct cs_range); i++) {
+		u32 base, option;
+		int cs = cs_ranges_buf[i].csnum;
+		if (cs >= ctrl_size / 8)
+			goto err;
+
+		if (cs_ranges_buf[i].base != 0)
+			goto err;
+
+		base = in_be32(&ctrl_addr[cs * 2]);
+
+		/* If CS is already valid, use the existing flags.
+		 * Otherwise, guess a sane default.
+		 */
+		if (base & 1) {
+			base &= 0x7fff;
+			option = in_be32(&ctrl_addr[cs * 2 + 1]) & 0x7fff;
+		} else {
+			base = 0x1801;
+			option = 0x10;
+		}
+
+		out_be32(&ctrl_addr[cs * 2], 0);
+		out_be32(&ctrl_addr[cs * 2 + 1],
+		         option | ~(cs_ranges_buf[i].size - 1));
+		out_be32(&ctrl_addr[cs * 2], base | cs_ranges_buf[i].addr);
+	}
+
+	return;
+
+err:
+	printf("Bad /localbus node\r\n");
+}
+
+/* Older u-boots don't set PCI up properly.  Update the hardware to match
+ * the device tree.  The prefetch mem region and non-prefetch mem region
+ * must be contiguous in the host bus.  As required by the PCI binding,
+ * PCI #addr/#size must be 3/2.  The parent bus must be 1/1.  Only
+ * 32-bit PCI is supported.  All three region types (prefetchable mem,
+ * non-prefetchable mem, and I/O) must be present.
+ */
+static void fixup_pci(void)
+{
+	struct pci_range *mem = NULL, *mmio = NULL,
+	                 *io = NULL, *mem_base = NULL;
+	u32 *pci_regs[3];
+	u8 *soc_regs;
+	int i, len;
+	void *node, *parent_node;
+	u32 naddr, nsize, mem_log2;
+
+	node = finddevice("/pci");
+	if (!node || !dt_is_compatible(node, "fsl,pq2-pci"))
+		return;
+
+	for (i = 0; i < 3; i++)
+		if (!dt_xlate_reg(node, i,
+		                  (unsigned long *)&pci_regs[i], NULL))
+			goto err;
+
+	soc_regs = (u8 *)fsl_get_immr();
+	if (!soc_regs)
+		goto err;
+
+	dt_get_reg_format(node, &naddr, &nsize);
+	if (naddr != 3 || nsize != 2)
+		goto err;
+
+	parent_node = get_parent(node);
+	if (!parent_node)
+		goto err;
+
+	dt_get_reg_format(parent_node, &naddr, &nsize);
+	if (naddr != 1 || nsize != 1)
+		goto err;
+
+	len = getprop(node, "ranges", pci_ranges_buf,
+	              sizeof(pci_ranges_buf));
+
+	for (i = 0; i < len / sizeof(struct pci_range); i++) {
+		u32 flags = pci_ranges_buf[i].flags & 0x43000000;
+
+		if (flags == 0x42000000)
+			mem = &pci_ranges_buf[i];
+		else if (flags == 0x02000000)
+			mmio = &pci_ranges_buf[i];
+		else if (flags == 0x01000000)
+			io = &pci_ranges_buf[i];
+	}
+
+	if (!mem || !mmio || !io)
+		goto err;
+
+	if (mem->phys_addr + mem->size[1] == mmio->phys_addr)
+		mem_base = mem;
+	else if (mmio->phys_addr + mmio->size[1] == mem->phys_addr)
+		mem_base = mmio;
+	else
+		goto err;
+
+	out_be32(&pci_regs[1][0], mem_base->phys_addr | 1);
+	out_be32(&pci_regs[2][0], ~(mem->size[1] + mmio->size[1] - 1));
+
+	out_be32(&pci_regs[1][1], io->phys_addr | 1);
+	out_be32(&pci_regs[2][1], ~(io->size[1] - 1));
+
+	out_le32(&pci_regs[0][0], mem->pci_addr[1] >> 12);
+	out_le32(&pci_regs[0][2], mem->phys_addr >> 12);
+	out_le32(&pci_regs[0][4], (~(mem->size[1] - 1) >> 12) | 0xa0000000);
+
+	out_le32(&pci_regs[0][6], mmio->pci_addr[1] >> 12);
+	out_le32(&pci_regs[0][8], mmio->phys_addr >> 12);
+	out_le32(&pci_regs[0][10], (~(mmio->size[1] - 1) >> 12) | 0x80000000);
+
+	out_le32(&pci_regs[0][12], io->pci_addr[1] >> 12);
+	out_le32(&pci_regs[0][14], io->phys_addr >> 12);
+	out_le32(&pci_regs[0][16], (~(io->size[1] - 1) >> 12) | 0xc0000000);
+
+	/* Inbound translation */
+	out_le32(&pci_regs[0][58], 0);
+	out_le32(&pci_regs[0][60], 0);
+
+	mem_log2 = 1 << (__ilog2_u32(bd.bi_memsize - 1) + 1);
+	out_le32(&pci_regs[0][62], 0xa0000000 | ~((1 << (mem_log2 - 12)) - 1));
+
+	/* If PCI is disabled, drive RST high to enable. */
+	if (!(in_le32(&pci_regs[0][32]) & 1)) {
+		 /* Tpvrh (Power valid to RST# high) 100 ms */
+		udelay(100000);
+
+		out_le32(&pci_regs[0][32], 1);
+
+		/* Trhfa (RST# high to first cfg access) 2^25 clocks */
+		udelay(1020000);
+	}
+
+	/* Enable bus master and memory access */
+	out_le32(&pci_regs[0][64], 0x80000004);
+	out_le32(&pci_regs[0][65], in_le32(&pci_regs[0][65]) | 6);
+
+	/* Park the bus on PCI, and elevate PCI's arbitration priority,
+	 * as required by section 9.6 of the user's manual.
+	 */
+	out_8(&soc_regs[0x10028], 3);
+	out_be32((u32 *)&soc_regs[0x1002c], 0x01236745);
+
+	return;
+
+err:
+	printf("Bad PCI node\r\n");
+}
+
+static void pq2_platform_fixups(void)
+{
+	void *node;
+
+	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+	dt_fixup_mac_addresses(bd.bi_enetaddr, bd.bi_enet1addr);
+	dt_fixup_cpu_clocks(bd.bi_intfreq, bd.bi_busfreq / 4, bd.bi_busfreq);
+
+	node = finddevice("/soc/cpm");
+	if (node)
+		setprop(node, "clock-frequency", &bd.bi_cpmfreq, 4);
+
+	node = finddevice("/soc/cpm/brg");
+	if (node)
+		setprop(node, "clock-frequency",  &bd.bi_brgfreq, 4);
+
+	update_cs_ranges();
+	fixup_pci();
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+                   unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	ft_init(_dtb_start, _dtb_end - _dtb_start, 32);
+	serial_console_init();
+	platform_ops.fixups = pq2_platform_fixups;
+}

arch/powerpc/boot/cuboot-sequoia.c

@@ -0,0 +1,56 @@
+/*
+ * Old U-boot compatibility for Sequoia
+ *
+ * Valentine Barshak <vbarshak@ru.mvista.com>
+ * Copyright 2007 MontaVista Software, Inc
+ *
+ * Based on Ebony code by David Gibson <david@gibson.dropbear.id.au>
+ * Copyright IBM Corporation, 2007
+ *
+ * Based on Bamboo code by Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ * Copyright IBM Corporation, 2007
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2 of the License
+ */
+
+#include <stdarg.h>
+#include <stddef.h>
+#include "types.h"
+#include "elf.h"
+#include "string.h"
+#include "stdio.h"
+#include "page.h"
+#include "ops.h"
+#include "dcr.h"
+#include "4xx.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_4xx
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+
+static void sequoia_fixups(void)
+{
+	unsigned long sysclk = 33333333;
+
+	ibm440ep_fixup_clocks(sysclk, 11059200);
+	ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
+	ibm4xx_denali_fixup_memsize();
+	dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+                   unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	platform_ops.fixups = sequoia_fixups;
+	platform_ops.exit = ibm44x_dbcr_reset;
+	ft_init(_dtb_start, 0, 32);
+	serial_console_init();
+}

arch/powerpc/boot/cuboot.c

@@ -17,9 +17,6 @@
 
 #include "ppcboot.h"
 
-extern char _end[];
-extern char _dtb_start[], _dtb_end[];
-
 void cuboot_init(unsigned long r4, unsigned long r5,
 		 unsigned long r6, unsigned long r7,
 		 unsigned long end_of_ram)

arch/powerpc/boot/dcr.h

@@ -121,4 +121,22 @@ static const unsigned long sdram_bxcr[] = { SDRAM0_B0CR, SDRAM0_B1CR, SDRAM0_B2C
 #define DCRN_CPC0_MIRQ1					0x0ed
 #define DCRN_CPC0_JTAGID				0x0ef
 
+#define DCRN_MAL0_CFG					0x180
+#define MAL_RESET 0x80000000
+
+/* 440EP Clock/Power-on Reset regs */
+#define DCRN_CPR0_ADDR	0xc
+#define DCRN_CPR0_DATA	0xd
+#define CPR0_PLLD0	0x60
+#define CPR0_OPBD0	0xc0
+#define CPR0_PERD0	0xe0
+#define CPR0_PRIMBD0	0xa0
+#define CPR0_SCPID	0x120
+#define CPR0_PLLC0	0x40
+
+/* 405GP Clocking/Power Management/Chip Control regs */
+#define DCRN_CPC0_PLLMR 0xb0
+#define DCRN_405_CPC0_CR0 0xb1
+#define DCRN_405_CPC0_CR1 0xb2
+
 #endif	/* _PPC_BOOT_DCR_H_ */

arch/powerpc/boot/devtree.c

@@ -74,6 +74,8 @@ void dt_fixup_cpu_clocks(u32 cpu, u32 tb, u32 bus)
 		if (bus > 0)
 			setprop_val(devp, "bus-frequency", bus);
 	}
+
+	timebase_period_ns = 1000000000 / tb;
 }
 
 void dt_fixup_clock(const char *path, u32 freq)
@@ -86,34 +88,38 @@ void dt_fixup_clock(const char *path, u32 freq)
 	}
 }
 
+void dt_fixup_mac_address(u32 index, const u8 *addr)
+{
+	void *devp = find_node_by_prop_value(NULL, "linux,network-index",
+	                                     (void*)&index, sizeof(index));
+
+	if (devp) {
+		printf("ENET%d: local-mac-address <-"
+		       " %02x:%02x:%02x:%02x:%02x:%02x\n\r", index,
+		       addr[0], addr[1], addr[2],
+		       addr[3], addr[4], addr[5]);
+
+		setprop(devp, "local-mac-address", addr, 6);
+	}
+}
+
 void __dt_fixup_mac_addresses(u32 startindex, ...)
 {
 	va_list ap;
 	u32 index = startindex;
-	void *devp;
 	const u8 *addr;
 
 	va_start(ap, startindex);
-	while ((addr = va_arg(ap, const u8 *))) {
-		devp = find_node_by_prop_value(NULL, "linux,network-index",
-					       (void*)&index, sizeof(index));
-
-		printf("ENET%d: local-mac-address <-"
-		       " %02x:%02x:%02x:%02x:%02x:%02x\n\r", index,
-		       addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]);
 
-		if (devp)
-			setprop(devp, "local-mac-address", addr, 6);
+	while ((addr = va_arg(ap, const u8 *)))
+		dt_fixup_mac_address(index++, addr);
 
-		index++;
-	}
 	va_end(ap);
 }
 
 #define MAX_ADDR_CELLS 4
-#define MAX_RANGES 8
 
-static void get_reg_format(void *node, u32 *naddr, u32 *nsize)
+void dt_get_reg_format(void *node, u32 *naddr, u32 *nsize)
 {
 	if (getprop(node, "#address-cells", naddr, 4) != 4)
 		*naddr = 2;
@@ -207,7 +213,7 @@ static int find_range(u32 *reg, u32 *ranges, int nregaddr,
  * In particular, PCI is not supported.  Also, only the beginning of the
  * reg block is tracked; size is ignored except in ranges.
  */
-static u32 dt_xlate_buf[MAX_ADDR_CELLS * MAX_RANGES * 3];
+static u32 prop_buf[MAX_PROP_LEN / 4];
 
 static int dt_xlate(void *node, int res, int reglen, unsigned long *addr,
 		unsigned long *size)
@@ -216,14 +222,14 @@ static int dt_xlate(void *node, int res, int reglen, unsigned long *addr,
 	u32 this_addr[MAX_ADDR_CELLS];
 	void *parent;
 	u64 ret_addr, ret_size;
-	u32 naddr, nsize, prev_naddr;
+	u32 naddr, nsize, prev_naddr, prev_nsize;
 	int buflen, offset;
 
 	parent = get_parent(node);
 	if (!parent)
 		return 0;
 
-	get_reg_format(parent, &naddr, &nsize);
+	dt_get_reg_format(parent, &naddr, &nsize);
 
 	if (nsize > 2)
 		return 0;
@@ -231,41 +237,47 @@ static int dt_xlate(void *node, int res, int reglen, unsigned long *addr,
 	offset = (naddr + nsize) * res;
 
 	if (reglen < offset + naddr + nsize ||
-	    sizeof(dt_xlate_buf) < offset + naddr + nsize)
+	    MAX_PROP_LEN < (offset + naddr + nsize) * 4)
 		return 0;
 
-	copy_val(last_addr, dt_xlate_buf + offset, naddr);
+	copy_val(last_addr, prop_buf + offset, naddr);
 
-	ret_size = dt_xlate_buf[offset + naddr];
+	ret_size = prop_buf[offset + naddr];
 	if (nsize == 2) {
 		ret_size <<= 32;
-		ret_size |= dt_xlate_buf[offset + naddr + 1];
+		ret_size |= prop_buf[offset + naddr + 1];
 	}
 
-	while ((node = get_parent(node))) {
+	for (;;) {
 		prev_naddr = naddr;
+		prev_nsize = nsize;
+		node = parent;
+
+		parent = get_parent(node);
+		if (!parent)
+			break;
 
-		get_reg_format(node, &naddr, &nsize);
+		dt_get_reg_format(parent, &naddr, &nsize);
 
-		buflen = getprop(node, "ranges", dt_xlate_buf,
-				sizeof(dt_xlate_buf));
-		if (buflen < 0)
+		buflen = getprop(node, "ranges", prop_buf,
+				sizeof(prop_buf));
+		if (buflen == 0)
 			continue;
-		if (buflen > sizeof(dt_xlate_buf))
+		if (buflen < 0 || buflen > sizeof(prop_buf))
 			return 0;
 
-		offset = find_range(last_addr, dt_xlate_buf, prev_naddr,
-		                    naddr, nsize, buflen / 4);
+		offset = find_range(last_addr, prop_buf, prev_naddr,
+		                    naddr, prev_nsize, buflen / 4);
 
 		if (offset < 0)
 			return 0;
 
-		copy_val(this_addr, dt_xlate_buf + offset, prev_naddr);
+		copy_val(this_addr, prop_buf + offset, prev_naddr);
 
 		if (!sub_reg(last_addr, this_addr))
 			return 0;
 
-		copy_val(this_addr, dt_xlate_buf + offset + prev_naddr, naddr);
+		copy_val(this_addr, prop_buf + offset + prev_naddr, naddr);
 
 		if (!add_reg(last_addr, this_addr, naddr))
 			return 0;
@@ -292,16 +304,35 @@ int dt_xlate_reg(void *node, int res, unsigned long *addr, unsigned long *size)
 {
 	int reglen;
 
-	reglen = getprop(node, "reg", dt_xlate_buf, sizeof(dt_xlate_buf)) / 4;
+	reglen = getprop(node, "reg", prop_buf, sizeof(prop_buf)) / 4;
 	return dt_xlate(node, res, reglen, addr, size);
 }
 
 int dt_xlate_addr(void *node, u32 *buf, int buflen, unsigned long *xlated_addr)
 {
 
-	if (buflen > sizeof(dt_xlate_buf))
+	if (buflen > sizeof(prop_buf))
 		return 0;
 
-	memcpy(dt_xlate_buf, buf, buflen);
+	memcpy(prop_buf, buf, buflen);
 	return dt_xlate(node, 0, buflen / 4, xlated_addr, NULL);
 }
+
+int dt_is_compatible(void *node, const char *compat)
+{
+	char *buf = (char *)prop_buf;
+	int len, pos;
+
+	len = getprop(node, "compatible", buf, MAX_PROP_LEN);
+	if (len < 0)
+		return 0;
+
+	for (pos = 0; pos < len; pos++) {
+		if (!strcmp(buf + pos, compat))
+			return 1;
+
+		pos += strnlen(&buf[pos], len - pos);
+	}
+
+	return 0;
+}

arch/powerpc/boot/dts/bamboo.dts

@@ -0,0 +1,244 @@
+/*
+ * Device Tree Source for AMCC Bamboo
+ *
+ * Copyright (c) 2006, 2007 IBM Corp.
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * FIXME: Draft only!
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	model = "amcc,bamboo";
+	compatible = "amcc,bamboo";
+	dcr-parent = <&/cpus/PowerPC,440EP@0>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,440EP@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <0>; /* Filled in by zImage */
+			timebase-frequency = <0>; /* Filled in by zImage */
+			i-cache-line-size = <20>;
+			d-cache-line-size = <20>;
+			i-cache-size = <8000>;
+			d-cache-size = <8000>;
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0 0>; /* Filled in by zImage */
+	};
+
+	UIC0: interrupt-controller0 {
+		compatible = "ibm,uic-440ep","ibm,uic";
+		interrupt-controller;
+		cell-index = <0>;
+		dcr-reg = <0c0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+	};
+
+	UIC1: interrupt-controller1 {
+		compatible = "ibm,uic-440ep","ibm,uic";
+		interrupt-controller;
+		cell-index = <1>;
+		dcr-reg = <0d0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupt-parent = <&UIC0>;
+	};
+
+	SDR0: sdr {
+		compatible = "ibm,sdr-440ep";
+		dcr-reg = <00e 002>;
+	};
+
+	CPR0: cpr {
+		compatible = "ibm,cpr-440ep";
+		dcr-reg = <00c 002>;
+	};
+
+	plb {
+		compatible = "ibm,plb-440ep", "ibm,plb-440gp", "ibm,plb4";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <0>; /* Filled in by zImage */
+
+		SDRAM0: sdram {
+			compatible = "ibm,sdram-440ep", "ibm,sdram-405gp";
+			dcr-reg = <010 2>;
+		};
+
+		DMA0: dma {
+			compatible = "ibm,dma-440ep", "ibm,dma-440gp";
+			dcr-reg = <100 027>;
+		};
+
+		MAL0: mcmal {
+			compatible = "ibm,mcmal-440ep", "ibm,mcmal-440gp", "ibm,mcmal";
+			dcr-reg = <180 62>;
+			num-tx-chans = <4>;
+			num-rx-chans = <2>;
+			interrupt-parent = <&MAL0>;
+			interrupts = <0 1 2 3 4>;
+			#interrupt-cells = <1>;
+			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+					/*RXEOB*/ 1 &UIC0 b 4
+					/*SERR*/  2 &UIC1 0 4
+					/*TXDE*/  3 &UIC1 1 4
+					/*RXDE*/  4 &UIC1 3 4>;
+		};
+
+		POB0: opb {
+		  	compatible = "ibm,opb-440ep", "ibm,opb-440gp", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* Bamboo is oddball in the 44x world and doesn't use the ERPN
+			 * bits.
+			 */
+		  	ranges = <00000000 0 00000000 80000000
+			          80000000 0 80000000 80000000>;
+		  	interrupt-parent = <&UIC1>;
+		  	interrupts = <7 4>;
+		  	clock-frequency = <0>; /* Filled in by zImage */
+
+			EBC0: ebc {
+				compatible = "ibm,ebc-440ep", "ibm,ebc-440gp", "ibm,ebc";
+				dcr-reg = <012 2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				clock-frequency = <0>; /* Filled in by zImage */
+				ranges;
+				interrupts = <5 1>;
+				interrupt-parent = <&UIC1>;
+			};
+
+			UART0: serial@ef600300 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600300 8>;
+		   		virtual-reg = <ef600300>;
+		   		clock-frequency = <0>; /* Filled in by zImage */
+		   		current-speed = <1c200>;
+		   		interrupt-parent = <&UIC0>;
+		   		interrupts = <0 4>;
+	   		};
+
+			UART1: serial@ef600400 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600400 8>;
+		   		virtual-reg = <ef600400>;
+		   		clock-frequency = <0>;
+		   		current-speed = <0>;
+		   		interrupt-parent = <&UIC0>;
+		   		interrupts = <1 4>;
+	   		};
+
+			UART2: serial@ef600500 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600500 8>;
+		   		virtual-reg = <ef600500>;
+		   		clock-frequency = <0>;
+		   		current-speed = <0>;
+		   		interrupt-parent = <&UIC0>;
+		   		interrupts = <3 4>;
+	   		};
+
+			UART3: serial@ef600600 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600600 8>;
+		   		virtual-reg = <ef600600>;
+		   		clock-frequency = <0>;
+		   		current-speed = <0>;
+		   		interrupt-parent = <&UIC0>;
+		   		interrupts = <4 4>;
+	   		};
+
+			IIC0: i2c@ef600700 {
+				device_type = "i2c";
+				compatible = "ibm,iic-440ep", "ibm,iic-440gp", "ibm,iic";
+				reg = <ef600700 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <2 4>;
+			};
+
+			IIC1: i2c@ef600800 {
+				device_type = "i2c";
+				compatible = "ibm,iic-440ep", "ibm,iic-440gp", "ibm,iic";
+				reg = <ef600800 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <7 4>;
+			};
+
+			ZMII0: emac-zmii@ef600d00 {
+				device_type = "zmii-interface";
+				compatible = "ibm,zmii-440ep", "ibm,zmii-440gp", "ibm,zmii";
+				reg = <ef600d00 c>;
+			};
+
+			EMAC0: ethernet@ef600e00 {
+				device_type = "network";
+				compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1c 4 1d 4>;
+				reg = <ef600e00 70>;
+				local-mac-address = [000000000000];
+				mal-device = <&MAL0>;
+				mal-tx-channel = <0 1>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <0>;
+			};
+
+			EMAC1: ethernet@ef600f00 {
+				device_type = "network";
+				compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1e 4 1f 4>;
+				reg = <ef600f00 70>;
+				local-mac-address = [000000000000];
+				mal-device = <&MAL0>;
+				mal-tx-channel = <2 3>;
+				mal-rx-channel = <1>;
+				cell-index = <1>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <1>;
+			};
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@ef600300";
+		bootargs = "console=ttyS0,115200";
+	};
+};

arch/powerpc/boot/dts/ebony.dts

@@ -9,10 +9,6 @@
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without
  * any warranty of any kind, whether express or implied.
- *
- * To build:
- *   dtc -I dts -O asm -o ebony.S -b 0 ebony.dts
- *   dtc -I dts -O dtb -o ebony.dtb -b 0 ebony.dts
  */
 
 / {
@@ -142,13 +138,16 @@
 				interrupt-parent = <&UIC1>;
 
 				small-flash@0,80000 {
-					device_type = "rom";
-					compatible = "direct-mapped";
-					probe-type = "JEDEC";
+					compatible = "jedec-flash";
 					bank-width = <1>;
-					partitions = <0 80000>;
-					partition-names = "OpenBIOS";
 					reg = <0 80000 80000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					partition@0 {
+						label = "OpenBIOS";
+						reg = <0 80000>;
+						read-only;
+					};
 				};
 
 				ds1743@1,0 {
@@ -158,14 +157,19 @@
 				};
 
 				large-flash@2,0 {
-					device_type = "rom";
-					compatible = "direct-mapped";
-					probe-type = "JEDEC";
+					compatible = "jedec-flash";
 					bank-width = <1>;
-					partitions = <0 380000
-						      380000 80000>;
-					partition-names = "fs", "firmware";
 					reg = <2 0 400000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					partition@0 {
+						label = "fs";
+						reg = <0 380000>;
+					};
+					partition@380000 {
+						label = "firmware";
+						reg = <380000 80000>;
+					};
 				};
 
 				ir@3,0 {
@@ -175,6 +179,7 @@
 				fpga@7,0 {
 					compatible = "Ebony-FPGA";
 					reg = <7 0 10>;
+					virtual-reg = <e8300000>;
 				};
 			};
 

arch/powerpc/boot/dts/ep88xc.dts

@@ -0,0 +1,214 @@
+/*
+ * EP88xC Device Tree Source
+ *
+ * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+
+/ {
+	model = "EP88xC";
+	compatible = "fsl,ep88xc";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,885@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <d#16>;
+			i-cache-line-size = <d#16>;
+			d-cache-size = <d#8192>;
+			i-cache-size = <d#8192>;
+			timebase-frequency = <0>;
+			bus-frequency = <0>;
+			clock-frequency = <0>;
+			interrupts = <f 2>;	// decrementer interrupt
+			interrupt-parent = <&PIC>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	localbus@fa200100 {
+		compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <fa200100 40>;
+
+		ranges = <
+			0 0 fc000000 04000000
+			3 0 fa000000 01000000
+		>;
+
+		flash@0,2000000 {
+			compatible = "cfi-flash";
+			reg = <0 2000000 2000000>;
+			bank-width = <4>;
+			device-width = <2>;
+		};
+
+		board-control@3,400000 {
+			reg = <3 400000 10>;
+			compatible = "fsl,ep88xc-bcsr";
+		};
+	};
+
+	soc@fa200000 {
+		compatible = "fsl,mpc885", "fsl,pq1-soc";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		ranges = <0 fa200000 00004000>;
+		bus-frequency = <0>;
+
+		// Temporary -- will go away once kernel uses ranges for get_immrbase().
+		reg = <fa200000 4000>;
+
+		mdio@e00 {
+			compatible = "fsl,mpc885-fec-mdio", "fsl,pq1-fec-mdio";
+			reg = <e00 188>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			PHY0: ethernet-phy@0 {
+				reg = <0>;
+				device_type = "ethernet-phy";
+			};
+
+			PHY1: ethernet-phy@1 {
+				reg = <1>;
+				device_type = "ethernet-phy";
+			};
+		};
+
+		ethernet@e00 {
+			device_type = "network";
+			compatible = "fsl,mpc885-fec-enet",
+			             "fsl,pq1-fec-enet";
+			reg = <e00 188>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <3 1>;
+			interrupt-parent = <&PIC>;
+			phy-handle = <&PHY0>;
+			linux,network-index = <0>;
+		};
+
+		ethernet@1e00 {
+			device_type = "network";
+			compatible = "fsl,mpc885-fec-enet",
+			             "fsl,pq1-fec-enet";
+			reg = <1e00 188>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <7 1>;
+			interrupt-parent = <&PIC>;
+			phy-handle = <&PHY1>;
+			linux,network-index = <1>;
+		};
+
+		PIC: interrupt-controller@0 {
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0 24>;
+			compatible = "fsl,mpc885-pic", "fsl,pq1-pic";
+		};
+
+		pcmcia@80 {
+			#address-cells = <3>;
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			compatible = "fsl,pq-pcmcia";
+			device_type = "pcmcia";
+			reg = <80 80>;
+			interrupt-parent = <&PIC>;
+			interrupts = <d 1>;
+		};
+
+		cpm@9c0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,mpc885-cpm", "fsl,cpm1";
+			command-proc = <9c0>;
+			interrupts = <0>;	// cpm error interrupt
+			interrupt-parent = <&CPM_PIC>;
+			reg = <9c0 40>;
+			ranges;
+
+			muram@2000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 2000 2000>;
+
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0 1c00>;
+				};
+			};
+
+			brg@9f0 {
+				compatible = "fsl,mpc885-brg",
+				             "fsl,cpm1-brg",
+				             "fsl,cpm-brg";
+				reg = <9f0 10>;
+			};
+
+			CPM_PIC: interrupt-controller@930 {
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupts = <5 2 0 2>;
+				interrupt-parent = <&PIC>;
+				reg = <930 20>;
+				compatible = "fsl,mpc885-cpm-pic",
+				             "fsl,cpm1-pic";
+			};
+
+			// MON-1
+			serial@a80 {
+				device_type = "serial";
+				compatible = "fsl,mpc885-smc-uart",
+				             "fsl,cpm1-smc-uart";
+				reg = <a80 10 3e80 40>;
+				interrupts = <4>;
+				interrupt-parent = <&CPM_PIC>;
+				fsl,cpm-brg = <1>;
+				fsl,cpm-command = <0090>;
+				linux,planetcore-label = "SMC1";
+			};
+
+			// SER-1
+			serial@a20 {
+				device_type = "serial";
+				compatible = "fsl,mpc885-scc-uart",
+				             "fsl,cpm1-scc-uart";
+				reg = <a20 20 3d00 80>;
+				interrupts = <1d>;
+				interrupt-parent = <&CPM_PIC>;
+				fsl,cpm-brg = <2>;
+				fsl,cpm-command = <0040>;
+				linux,planetcore-label = "SCC2";
+			};
+
+			usb@a00 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,mpc885-usb",
+				             "fsl,cpm1-usb";
+				reg = <a00 18 1c00 80>;
+				interrupt-parent = <&CPM_PIC>;
+				interrupts = <1e>;
+				fsl,cpm-command = <0000>;
+			};
+		};
+	};
+};

arch/powerpc/boot/dts/holly.dts

@@ -8,10 +8,6 @@
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without
  * any warranty of any kind, whether express or implied.
- *
- * To build:
- *   dtc -I dts -O asm -o holly.S -b 0 holly.dts
- *   dtc -I dts -O dtb -o holly.dtb -b 0 holly.dts
  */
 
 / {
@@ -35,7 +31,6 @@
 			timebase-frequency = <2faf080>;
 			clock-frequency = <23c34600>;
 			bus-frequency = <bebc200>;
-			32-bit;
 		};
 	};
 

arch/powerpc/boot/dts/kilauea.dts

@@ -0,0 +1,252 @@
+/*
+ * Device Tree Source for AMCC Kilauea (405EX)
+ *
+ * Copyright 2007 DENX Software Engineering, Stefan Roese <sr@denx.de>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "amcc,kilauea";
+	compatible = "amcc,kilauea";
+	dcr-parent = <&/cpus/PowerPC,405EX@0>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,405EX@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <0>; /* Filled in by U-Boot */
+			timebase-frequency = <0>; /* Filled in by U-Boot */
+			i-cache-line-size = <20>;
+			d-cache-line-size = <20>;
+			i-cache-size = <4000>; /* 16 kB */
+			d-cache-size = <4000>; /* 16 kB */
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>; /* Filled in by U-Boot */
+	};
+
+	UIC0: interrupt-controller {
+		compatible = "ibm,uic-405ex", "ibm,uic";
+		interrupt-controller;
+		cell-index = <0>;
+		dcr-reg = <0c0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+	};
+
+	UIC1: interrupt-controller1 {
+		compatible = "ibm,uic-405ex","ibm,uic";
+		interrupt-controller;
+		cell-index = <1>;
+		dcr-reg = <0d0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupt-parent = <&UIC0>;
+	};
+
+	UIC2: interrupt-controller2 {
+		compatible = "ibm,uic-405ex","ibm,uic";
+		interrupt-controller;
+		cell-index = <2>;
+		dcr-reg = <0e0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <1c 4 1d 4>; /* cascade */
+		interrupt-parent = <&UIC0>;
+	};
+
+	plb {
+		compatible = "ibm,plb-405ex", "ibm,plb4";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <0>; /* Filled in by U-Boot */
+
+		SDRAM0: memory-controller {
+			compatible = "ibm,sdram-405ex";
+			dcr-reg = <010 2>;
+		};
+
+		MAL0: mcmal {
+			compatible = "ibm,mcmal-405ex", "ibm,mcmal2";
+			dcr-reg = <180 62>;
+			num-tx-chans = <2>;
+			num-rx-chans = <2>;
+			interrupt-parent = <&MAL0>;
+			interrupts = <0 1 2 3 4>;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+					/*RXEOB*/ 1 &UIC0 b 4
+					/*SERR*/  2 &UIC1 0 4
+					/*TXDE*/  3 &UIC1 1 4
+					/*RXDE*/  4 &UIC1 2 4>;
+			interrupt-map-mask = <ffffffff>;
+		};
+
+		POB0: opb {
+			compatible = "ibm,opb-405ex", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <80000000 80000000 10000000
+				  ef600000 ef600000 a00000
+				  f0000000 f0000000 10000000>;
+			dcr-reg = <0a0 5>;
+			clock-frequency = <0>; /* Filled in by U-Boot */
+
+			EBC0: ebc {
+				compatible = "ibm,ebc-405ex", "ibm,ebc";
+				dcr-reg = <012 2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				clock-frequency = <0>; /* Filled in by U-Boot */
+				/* ranges property is supplied by U-Boot */
+				interrupts = <5 1>;
+				interrupt-parent = <&UIC1>;
+
+				nor_flash@0,0 {
+					compatible = "amd,s29gl512n", "cfi-flash";
+					bank-width = <2>;
+					reg = <0 000000 4000000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					partition@0 {
+						label = "kernel";
+						reg = <0 200000>;
+					};
+					partition@200000 {
+						label = "root";
+						reg = <200000 200000>;
+					};
+					partition@400000 {
+						label = "user";
+						reg = <400000 3b60000>;
+					};
+					partition@3f60000 {
+						label = "env";
+						reg = <3f60000 40000>;
+					};
+					partition@3fa0000 {
+						label = "u-boot";
+						reg = <3fa0000 60000>;
+					};
+				};
+			};
+
+			UART0: serial@ef600200 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <ef600200 8>;
+				virtual-reg = <ef600200>;
+				clock-frequency = <0>; /* Filled in by U-Boot */
+				current-speed = <0>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <1a 4>;
+			};
+
+			UART1: serial@ef600300 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <ef600300 8>;
+				virtual-reg = <ef600300>;
+				clock-frequency = <0>; /* Filled in by U-Boot */
+				current-speed = <0>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <1 4>;
+			};
+
+			IIC0: i2c@ef600400 {
+				device_type = "i2c";
+				compatible = "ibm,iic-405ex", "ibm,iic";
+				reg = <ef600400 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <2 4>;
+			};
+
+			IIC1: i2c@ef600500 {
+				device_type = "i2c";
+				compatible = "ibm,iic-405ex", "ibm,iic";
+				reg = <ef600500 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <7 4>;
+			};
+
+
+			RGMII0: emac-rgmii@ef600b00 {
+				device_type = "rgmii-interface";
+				compatible = "ibm,rgmii-405ex", "ibm,rgmii";
+				reg = <ef600b00 104>;
+			};
+
+			EMAC0: ethernet@ef600900 {
+				linux,network-index = <0>;
+				device_type = "network";
+				compatible = "ibm,emac-405ex", "ibm,emac4";
+				interrupt-parent = <&EMAC0>;
+				interrupts = <0 1>;
+				#interrupt-cells = <1>;
+				#address-cells = <0>;
+				#size-cells = <0>;
+				interrupt-map = </*Status*/ 0 &UIC0 18 4
+						/*Wake*/  1 &UIC1 1d 4>;
+				reg = <ef600900 70>;
+				local-mac-address = [000000000000]; /* Filled in by U-Boot */
+				mal-device = <&MAL0>;
+				mal-tx-channel = <0>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rgmii";
+				phy-map = <00000000>;
+				rgmii-device = <&RGMII0>;
+				rgmii-channel = <0>;
+			};
+
+			EMAC1: ethernet@ef600a00 {
+				linux,network-index = <1>;
+				device_type = "network";
+				compatible = "ibm,emac-405ex", "ibm,emac4";
+				interrupt-parent = <&EMAC1>;
+				interrupts = <0 1>;
+				#interrupt-cells = <1>;
+				#address-cells = <0>;
+				#size-cells = <0>;
+				interrupt-map = </*Status*/ 0 &UIC0 19 4
+						/*Wake*/  1 &UIC1 1f 4>;
+				reg = <ef600a00 70>;
+				local-mac-address = [000000000000]; /* Filled in by U-Boot */
+				mal-device = <&MAL0>;
+				mal-tx-channel = <1>;
+				mal-rx-channel = <1>;
+				cell-index = <1>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rgmii";
+				phy-map = <00000000>;
+				rgmii-device = <&RGMII0>;
+				rgmii-channel = <1>;
+			};
+		};
+	};
+};

arch/powerpc/boot/dts/kuroboxHD.dts

@@ -15,9 +15,6 @@
 
 XXXX add flash parts, rtc, ??
 
-build with: "dtc -f -I dts -O dtb -o kuroboxHD.dtb -V 16 kuroboxHD.dts"
-
-
  */
 
 / {
@@ -50,7 +47,6 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHD.dtb -V 16 kuroboxHD.dts"
 	soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		compatible = "mpc10x";
 		store-gathering = <0>; /* 0 == off, !0 == on */
@@ -72,7 +68,7 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHD.dtb -V 16 kuroboxHD.dts"
 
 			rtc@32 {
 				device_type = "rtc";
-				compatible = "ricoh,rs5c372b";
+				compatible = "ricoh,rs5c372a";
 				reg = <32>;
 			};
 		};
@@ -83,7 +79,7 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHD.dtb -V 16 kuroboxHD.dts"
 			reg = <80004500 8>;
 			clock-frequency = <5d08d88>;
 			current-speed = <2580>;
-			interrupts = <9 2>;
+			interrupts = <9 0>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -104,7 +100,6 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHD.dtb -V 16 kuroboxHD.dts"
 			compatible = "chrp,open-pic";
 			interrupt-controller;
 			reg = <80040000 40000>;
-			built-in;
 		};
 
 		pci@fec00000 {

arch/powerpc/boot/dts/kuroboxHG.dts

@@ -15,9 +15,6 @@
 
 XXXX add flash parts, rtc, ??
 
-build with: "dtc -f -I dts -O dtb -o kuroboxHG.dtb -V 16 kuroboxHG.dts"
-
-
  */
 
 / {
@@ -50,7 +47,6 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHG.dtb -V 16 kuroboxHG.dts"
 	soc10x { /* AFAICT need to make soc for 8245's uarts to be defined */
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		compatible = "mpc10x";
 		store-gathering = <0>; /* 0 == off, !0 == on */
@@ -72,7 +68,7 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHG.dtb -V 16 kuroboxHG.dts"
 
 			rtc@32 {
 				device_type = "rtc";
-				compatible = "ricoh,rs5c372b";
+				compatible = "ricoh,rs5c372a";
 				reg = <32>;
 			};
 		};
@@ -83,7 +79,7 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHG.dtb -V 16 kuroboxHG.dts"
 			reg = <80004500 8>;
 			clock-frequency = <7c044a8>;
 			current-speed = <2580>;
-			interrupts = <9 2>;
+			interrupts = <9 0>;
 			interrupt-parent = <&mpic>;
 		};
 
@@ -104,7 +100,6 @@ build with: "dtc -f -I dts -O dtb -o kuroboxHG.dtb -V 16 kuroboxHG.dts"
 			compatible = "chrp,open-pic";
 			interrupt-controller;
 			reg = <80040000 40000>;
-			built-in;
 		};
 
 		pci@fec00000 {

arch/powerpc/boot/dts/lite5200.dts

@@ -19,7 +19,7 @@
 / {
 	model = "fsl,lite5200";
 	// revision = "1.0";
-	compatible = "fsl,lite5200\0generic-mpc5200";
+	compatible = "fsl,lite5200","generic-mpc5200";
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -37,7 +37,6 @@
 			timebase-frequency = <0>;	// from bootloader
 			bus-frequency = <0>;		// from bootloader
 			clock-frequency = <0>;		// from bootloader
-			32-bit;
 		};
 	};
 
@@ -50,10 +49,9 @@
 		model = "fsl,mpc5200";
 		compatible = "mpc5200";
 		revision = "";			// from bootloader
-		#interrupt-cells = <3>;
 		device_type = "soc";
-		ranges = <0 f0000000 f0010000>;
-		reg = <f0000000 00010000>;
+		ranges = <0 f0000000 0000c000>;
+		reg = <f0000000 00000100>;
 		bus-frequency = <0>;		// from bootloader
 		system-frequency = <0>;		// from bootloader
 
@@ -69,7 +67,6 @@
 			device_type = "interrupt-controller";
 			compatible = "mpc5200-pic";
 			reg = <500 80>;
-			built-in;
 		};
 
 		gpt@600 {	// General Purpose Timer
@@ -185,27 +182,6 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		pci@0d00 {
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			device_type = "pci";
-			compatible = "mpc5200-pci";
-			reg = <d00 100>;
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3
-			                 c000 0 0 2 &mpc5200_pic 0 0 3
-			                 c000 0 0 3 &mpc5200_pic 0 0 3
-			                 c000 0 0 4 &mpc5200_pic 0 0 3>;
-			clock-frequency = <0>; // From boot loader
-			interrupts = <2 8 0 2 9 0 2 a 0>;
-			interrupt-parent = <&mpc5200_pic>;
-			bus-range = <0 0>;
-			ranges = <42000000 0 80000000 80000000 0 20000000
-			          02000000 0 a0000000 a0000000 0 10000000
-			          01000000 0 00000000 b0000000 0 01000000>;
-		};
-
 		spi@f00 {
 			device_type = "spi";
 			compatible = "mpc5200-spi";
@@ -216,7 +192,7 @@
 
 		usb@1000 {
 			device_type = "usb-ohci-be";
-			compatible = "mpc5200-ohci\0ohci-be";
+			compatible = "mpc5200-ohci","ohci-be";
 			reg = <1000 ff>;
 			interrupts = <2 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -317,7 +293,7 @@
 
 		i2c@3d00 {
 			device_type = "i2c";
-			compatible = "mpc5200-i2c\0fsl-i2c";
+			compatible = "mpc5200-i2c","fsl-i2c";
 			cell-index = <0>;
 			reg = <3d00 40>;
 			interrupts = <2 f 0>;
@@ -327,7 +303,7 @@
 
 		i2c@3d40 {
 			device_type = "i2c";
-			compatible = "mpc5200-i2c\0fsl-i2c";
+			compatible = "mpc5200-i2c","fsl-i2c";
 			cell-index = <1>;
 			reg = <3d40 40>;
 			interrupts = <2 10 0>;
@@ -336,8 +312,29 @@
 		};
 		sram@8000 {
 			device_type = "sram";
-			compatible = "mpc5200-sram\0sram";
+			compatible = "mpc5200-sram","sram";
 			reg = <8000 4000>;
 		};
 	};
+
+	pci@f0000d00 {
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		compatible = "mpc5200-pci";
+		reg = <f0000d00 100>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3
+				 c000 0 0 2 &mpc5200_pic 0 0 3
+				 c000 0 0 3 &mpc5200_pic 0 0 3
+				 c000 0 0 4 &mpc5200_pic 0 0 3>;
+		clock-frequency = <0>; // From boot loader
+		interrupts = <2 8 0 2 9 0 2 a 0>;
+		interrupt-parent = <&mpc5200_pic>;
+		bus-range = <0 0>;
+		ranges = <42000000 0 80000000 80000000 0 20000000
+			  02000000 0 a0000000 a0000000 0 10000000
+			  01000000 0 00000000 b0000000 0 01000000>;
+	};
 };

arch/powerpc/boot/dts/lite5200b.dts

@@ -19,7 +19,7 @@
 / {
 	model = "fsl,lite5200b";
 	// revision = "1.0";
-	compatible = "fsl,lite5200b\0generic-mpc5200";
+	compatible = "fsl,lite5200b","generic-mpc5200";
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -37,7 +37,6 @@
 			timebase-frequency = <0>;	// from bootloader
 			bus-frequency = <0>;		// from bootloader
 			clock-frequency = <0>;		// from bootloader
-			32-bit;
 		};
 	};
 
@@ -50,15 +49,14 @@
 		model = "fsl,mpc5200b";
 		compatible = "mpc5200";
 		revision = "";			// from bootloader
-		#interrupt-cells = <3>;
 		device_type = "soc";
-		ranges = <0 f0000000 f0010000>;
-		reg = <f0000000 00010000>;
+		ranges = <0 f0000000 0000c000>;
+		reg = <f0000000 00000100>;
 		bus-frequency = <0>;		// from bootloader
 		system-frequency = <0>;		// from bootloader
 
 		cdm@200 {
-			compatible = "mpc5200b-cdm\0mpc5200-cdm";
+			compatible = "mpc5200b-cdm","mpc5200-cdm";
 			reg = <200 38>;
 		};
 
@@ -67,13 +65,12 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			device_type = "interrupt-controller";
-			compatible = "mpc5200b-pic\0mpc5200-pic";
+			compatible = "mpc5200b-pic","mpc5200-pic";
 			reg = <500 80>;
-			built-in;
 		};
 
 		gpt@600 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <0>;
 			reg = <600 10>;
@@ -83,7 +80,7 @@
 		};
 
 		gpt@610 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <1>;
 			reg = <610 10>;
@@ -92,7 +89,7 @@
 		};
 
 		gpt@620 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <2>;
 			reg = <620 10>;
@@ -101,7 +98,7 @@
 		};
 
 		gpt@630 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <3>;
 			reg = <630 10>;
@@ -110,7 +107,7 @@
 		};
 
 		gpt@640 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <4>;
 			reg = <640 10>;
@@ -119,7 +116,7 @@
 		};
 
 		gpt@650 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <5>;
 			reg = <650 10>;
@@ -128,7 +125,7 @@
 		};
 
 		gpt@660 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <6>;
 			reg = <660 10>;
@@ -137,7 +134,7 @@
 		};
 
 		gpt@670 {	// General Purpose Timer
-			compatible = "mpc5200b-gpt\0mpc5200-gpt";
+			compatible = "mpc5200b-gpt","mpc5200-gpt";
 			device_type = "gpt";
 			cell-index = <7>;
 			reg = <670 10>;
@@ -146,7 +143,7 @@
 		};
 
 		rtc@800 {	// Real time clock
-			compatible = "mpc5200b-rtc\0mpc5200-rtc";
+			compatible = "mpc5200b-rtc","mpc5200-rtc";
 			device_type = "rtc";
 			reg = <800 100>;
 			interrupts = <1 5 0 1 6 0>;
@@ -155,7 +152,7 @@
 
 		mscan@900 {
 			device_type = "mscan";
-			compatible = "mpc5200b-mscan\0mpc5200-mscan";
+			compatible = "mpc5200b-mscan","mpc5200-mscan";
 			cell-index = <0>;
 			interrupts = <2 11 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -164,7 +161,7 @@
 
 		mscan@980 {
 			device_type = "mscan";
-			compatible = "mpc5200b-mscan\0mpc5200-mscan";
+			compatible = "mpc5200b-mscan","mpc5200-mscan";
 			cell-index = <1>;
 			interrupts = <2 12 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -172,48 +169,22 @@
 		};
 
 		gpio@b00 {
-			compatible = "mpc5200b-gpio\0mpc5200-gpio";
+			compatible = "mpc5200b-gpio","mpc5200-gpio";
 			reg = <b00 40>;
 			interrupts = <1 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		gpio-wkup@c00 {
-			compatible = "mpc5200b-gpio-wkup\0mpc5200-gpio-wkup";
+			compatible = "mpc5200b-gpio-wkup","mpc5200-gpio-wkup";
 			reg = <c00 40>;
 			interrupts = <1 8 0 0 3 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		pci@0d00 {
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			device_type = "pci";
-			compatible = "mpc5200b-pci\0mpc5200-pci";
-			reg = <d00 100>;
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
-			                 c000 0 0 2 &mpc5200_pic 1 1 3
-			                 c000 0 0 3 &mpc5200_pic 1 2 3
-			                 c000 0 0 4 &mpc5200_pic 1 3 3
-
-			                 c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
-			                 c800 0 0 2 &mpc5200_pic 1 2 3
-			                 c800 0 0 3 &mpc5200_pic 1 3 3
-			                 c800 0 0 4 &mpc5200_pic 0 0 3>;
-			clock-frequency = <0>; // From boot loader
-			interrupts = <2 8 0 2 9 0 2 a 0>;
-			interrupt-parent = <&mpc5200_pic>;
-			bus-range = <0 0>;
-			ranges = <42000000 0 80000000 80000000 0 20000000
-			          02000000 0 a0000000 a0000000 0 10000000
-			          01000000 0 00000000 b0000000 0 01000000>;
-		};
-
 		spi@f00 {
 			device_type = "spi";
-			compatible = "mpc5200b-spi\0mpc5200-spi";
+			compatible = "mpc5200b-spi","mpc5200-spi";
 			reg = <f00 20>;
 			interrupts = <2 d 0 2 e 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -221,7 +192,7 @@
 
 		usb@1000 {
 			device_type = "usb-ohci-be";
-			compatible = "mpc5200b-ohci\0mpc5200-ohci\0ohci-be";
+			compatible = "mpc5200b-ohci","mpc5200-ohci","ohci-be";
 			reg = <1000 ff>;
 			interrupts = <2 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -229,7 +200,7 @@
 
 		bestcomm@1200 {
 			device_type = "dma-controller";
-			compatible = "mpc5200b-bestcomm\0mpc5200-bestcomm";
+			compatible = "mpc5200b-bestcomm","mpc5200-bestcomm";
 			reg = <1200 80>;
 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
 			              3 4 0  3 5 0  3 6 0  3 7 0
@@ -239,13 +210,13 @@
 		};
 
 		xlb@1f00 {
-			compatible = "mpc5200b-xlb\0mpc5200-xlb";
+			compatible = "mpc5200b-xlb","mpc5200-xlb";
 			reg = <1f00 100>;
 		};
 
 		serial@2000 {		// PSC1
 			device_type = "serial";
-			compatible = "mpc5200b-psc-uart\0mpc5200-psc-uart";
+			compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
 			port-number = <0>;  // Logical port assignment
 			cell-index = <0>;
 			reg = <2000 100>;
@@ -256,7 +227,7 @@
 		// PSC2 in ac97 mode example
 		//ac97@2200 {		// PSC2
 		//	device_type = "sound";
-		//	compatible = "mpc5200b-psc-ac97\0mpc5200-psc-ac97";
+		//	compatible = "mpc5200b-psc-ac97","mpc5200-psc-ac97";
 		//	cell-index = <1>;
 		//	reg = <2200 100>;
 		//	interrupts = <2 2 0>;
@@ -276,7 +247,7 @@
 		// PSC4 in uart mode example
 		//serial@2600 {		// PSC4
 		//	device_type = "serial";
-		//	compatible = "mpc5200b-psc-uart\0mpc5200-psc-uart";
+		//	compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
 		//	cell-index = <3>;
 		//	reg = <2600 100>;
 		//	interrupts = <2 b 0>;
@@ -286,7 +257,7 @@
 		// PSC5 in uart mode example
 		//serial@2800 {		// PSC5
 		//	device_type = "serial";
-		//	compatible = "mpc5200b-psc-uart\0mpc5200-psc-uart";
+		//	compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
 		//	cell-index = <4>;
 		//	reg = <2800 100>;
 		//	interrupts = <2 c 0>;
@@ -296,7 +267,7 @@
 		// PSC6 in spi mode example
 		//spi@2c00 {		// PSC6
 		//	device_type = "spi";
-		//	compatible = "mpc5200b-psc-spi\0mpc5200-psc-spi";
+		//	compatible = "mpc5200b-psc-spi","mpc5200-psc-spi";
 		//	cell-index = <5>;
 		//	reg = <2c00 100>;
 		//	interrupts = <2 4 0>;
@@ -305,7 +276,7 @@
 
 		ethernet@3000 {
 			device_type = "network";
-			compatible = "mpc5200b-fec\0mpc5200-fec";
+			compatible = "mpc5200b-fec","mpc5200-fec";
 			reg = <3000 800>;
 			mac-address = [ 02 03 04 05 06 07 ]; // Bad!
 			interrupts = <2 5 0>;
@@ -314,7 +285,7 @@
 
 		ata@3a00 {
 			device_type = "ata";
-			compatible = "mpc5200b-ata\0mpc5200-ata";
+			compatible = "mpc5200b-ata","mpc5200-ata";
 			reg = <3a00 100>;
 			interrupts = <2 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -322,7 +293,7 @@
 
 		i2c@3d00 {
 			device_type = "i2c";
-			compatible = "mpc5200b-i2c\0mpc5200-i2c\0fsl-i2c";
+			compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
 			cell-index = <0>;
 			reg = <3d00 40>;
 			interrupts = <2 f 0>;
@@ -332,7 +303,7 @@
 
 		i2c@3d40 {
 			device_type = "i2c";
-			compatible = "mpc5200b-i2c\0mpc5200-i2c\0fsl-i2c";
+			compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
 			cell-index = <1>;
 			reg = <3d40 40>;
 			interrupts = <2 10 0>;
@@ -341,8 +312,34 @@
 		};
 		sram@8000 {
 			device_type = "sram";
-			compatible = "mpc5200b-sram\0mpc5200-sram\0sram";
+			compatible = "mpc5200b-sram","mpc5200-sram","sram";
 			reg = <8000 4000>;
 		};
 	};
+
+	pci@f0000d00 {
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		compatible = "mpc5200b-pci","mpc5200-pci";
+		reg = <f0000d00 100>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
+				 c000 0 0 2 &mpc5200_pic 1 1 3
+				 c000 0 0 3 &mpc5200_pic 1 2 3
+				 c000 0 0 4 &mpc5200_pic 1 3 3
+
+				 c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
+				 c800 0 0 2 &mpc5200_pic 1 2 3
+				 c800 0 0 3 &mpc5200_pic 1 3 3
+				 c800 0 0 4 &mpc5200_pic 0 0 3>;
+		clock-frequency = <0>; // From boot loader
+		interrupts = <2 8 0 2 9 0 2 a 0>;
+		interrupt-parent = <&mpc5200_pic>;
+		bus-range = <0 0>;
+		ranges = <42000000 0 80000000 80000000 0 20000000
+			  02000000 0 a0000000 a0000000 0 10000000
+			  01000000 0 00000000 b0000000 0 01000000>;
+	};
 };

arch/powerpc/boot/dts/mpc7448hpc2.dts

@@ -31,7 +31,6 @@
 			timebase-frequency = <0>;	// 33 MHz, from uboot
 			clock-frequency = <0>;		// From U-Boot
 			bus-frequency = <0>;		// From U-Boot
-			32-bit;
 		};
 	};
 
@@ -44,7 +43,6 @@
   	tsi108@c0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "tsi-bridge";
 		ranges = <00000000 c0000000 00010000>;
 		reg = <c0000000 00010000>;
@@ -80,6 +78,7 @@
 		};
 
 		ethernet@6200 {
+			linux,network-index = <0>;
 			#size-cells = <0>;
 			device_type = "network";
 			compatible = "tsi108-ethernet";
@@ -92,6 +91,7 @@
 		};
 
 		ethernet@6600 {
+			linux,network-index = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			device_type = "network";
@@ -128,7 +128,6 @@
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <7400 400>;
-			built-in;
 			compatible = "chrp,open-pic";
 			device_type = "open-pic";
                        	big-endian;
@@ -180,12 +179,14 @@
 				device_type = "pic-router";
 				#address-cells = <0>;
 				#interrupt-cells = <2>;
-				built-in;
 				big-endian;
 				interrupts = <17 2>;
 				interrupt-parent = <&mpic>;
 			};
 		};
 	};
+	chosen {
+		linux,stdout-path = "/tsi108@c0000000/serial@7808";
+	};
 
 };

arch/powerpc/boot/dts/mpc8272ads.dts

@@ -10,207 +10,240 @@
  */
 
 / {
-       model = "MPC8272ADS";
-       compatible = "MPC8260ADS";
-       #address-cells = <1>;
-       #size-cells = <1>;
-
-       cpus {
-               #address-cells = <1>;
-               #size-cells = <0>;
-
-               PowerPC,8272@0 {
-                       device_type = "cpu";
-                       reg = <0>;
-                       d-cache-line-size = <20>;       // 32 bytes
-                       i-cache-line-size = <20>;       // 32 bytes
-                       d-cache-size = <4000>;          // L1, 16K
-                       i-cache-size = <4000>;          // L1, 16K
-                       timebase-frequency = <0>;
-                       bus-frequency = <0>;
-                       clock-frequency = <0>;
-                       32-bit;
-               };
-       };
-
-		pci_pic: interrupt-controller@f8200000 {
-               #address-cells = <0>;
-               #interrupt-cells = <2>;
-               interrupt-controller;
-               reg = <f8200000 f8200004>;
-               built-in;
-               device_type = "pci-pic";
-       };
-       memory {
-               device_type = "memory";
-               reg = <00000000 4000000 f4500000 00000020>;
-       };
-
-       chosen {
-               name = "chosen";
-               linux,platform = <0>;
-		interrupt-controller = <&Cpm_pic>;
-       };
-
-       soc8272@f0000000 {
-               #address-cells = <1>;
-               #size-cells = <1>;
-               #interrupt-cells = <2>;
-               device_type = "soc";
-               ranges = <00000000 f0000000 00053000>;
-               reg = <f0000000 10000>;
-
-               mdio@0 {
-                       device_type = "mdio";
-                       compatible = "fs_enet";
-                       reg = <0 0>;
-                       #address-cells = <1>;
-                       #size-cells = <0>;
-			phy0:ethernet-phy@0 {
-				interrupt-parent = <&Cpm_pic>;
-                               interrupts = <17 4>;
-                               reg = <0>;
-                               bitbang = [ 12 12 13 02 02 01 ];
-                               device_type = "ethernet-phy";
-                       };
-			phy1:ethernet-phy@1 {
-				interrupt-parent = <&Cpm_pic>;
-                               interrupts = <17 4>;
-                               bitbang = [ 12 12 13 02 02 01 ];
-                               reg = <3>;
-                               device_type = "ethernet-phy";
-                       };
-               };
-
-               ethernet@24000 {
-                       #address-cells = <1>;
-                       #size-cells = <0>;
-                       device_type = "network";
-                       device-id = <1>;
-                       compatible = "fs_enet";
-                       model = "FCC";
-                       reg = <11300 20 8400 100 11380 30>;
-                       mac-address = [ 00 11 2F 99 43 54 ];
-                       interrupts = <20 2>;
-			interrupt-parent = <&Cpm_pic>;
-			phy-handle = <&Phy0>;
-                       rx-clock = <13>;
-                       tx-clock = <12>;
-               };
-
-               ethernet@25000 {
-                       device_type = "network";
-                       device-id = <2>;
-                       compatible = "fs_enet";
-                       model = "FCC";
-                       reg = <11320 20 8500 100 113b0 30>;
-                       mac-address = [ 00 11 2F 99 44 54 ];
-                       interrupts = <21 2>;
-			interrupt-parent = <&Cpm_pic>;
-			phy-handle = <&Phy1>;
-                       rx-clock = <17>;
-                       tx-clock = <18>;
-               };
-
-               cpm@f0000000 {
-                       #address-cells = <1>;
-                       #size-cells = <1>;
-                       #interrupt-cells = <2>;
-                       device_type = "cpm";
-                       model = "CPM2";
-                       ranges = <00000000 00000000 20000>;
-                       reg = <0 20000>;
-                       command-proc = <119c0>;
-                       brg-frequency = <17D7840>;
-                       cpm_clk = <BEBC200>;
-
-                       scc@11a00 {
-                               device_type = "serial";
-                               compatible = "cpm_uart";
-                               model = "SCC";
-                               device-id = <1>;
-                               reg = <11a00 20 8000 100>;
-                               current-speed = <1c200>;
-                               interrupts = <28 2>;
-				interrupt-parent = <&Cpm_pic>;
-                               clock-setup = <0 00ffffff>;
-                               rx-clock = <1>;
-                               tx-clock = <1>;
-                       };
-
-                       scc@11a60 {
-                               device_type = "serial";
-                               compatible = "cpm_uart";
-                               model = "SCC";
-                               device-id = <4>;
-                               reg = <11a60 20 8300 100>;
-                               current-speed = <1c200>;
-                               interrupts = <2b 2>;
-				interrupt-parent = <&Cpm_pic>;
-                               clock-setup = <1b ffffff00>;
-                               rx-clock = <4>;
-                               tx-clock = <4>;
-                       };
-
-               };
-			cpm_pic:interrupt-controller@10c00 {
-                       #address-cells = <0>;
-                       #interrupt-cells = <2>;
-                       interrupt-controller;
-                       reg = <10c00 80>;
-                       built-in;
-                       device_type = "cpm-pic";
-		       compatible = "CPM2";
-               };
-               pci@0500 {
-                       #interrupt-cells = <1>;
-                       #size-cells = <2>;
-                       #address-cells = <3>;
-                       compatible = "8272";
-                       device_type = "pci";
-                       reg = <10430 4dc>;
-                       clock-frequency = <3f940aa>;
-                       interrupt-map-mask = <f800 0 0 7>;
-                       interrupt-map = <
-
-                                       /* IDSEL 0x16 */
-                                        b000 0 0 1 f8200000 40 8
-                                        b000 0 0 2 f8200000 41 8
-                                        b000 0 0 3 f8200000 42 8
-                                        b000 0 0 4 f8200000 43 8
-
-                                       /* IDSEL 0x17 */
-                                        b800 0 0 1 f8200000 43 8
-                                        b800 0 0 2 f8200000 40 8
-                                        b800 0 0 3 f8200000 41 8
-                                        b800 0 0 4 f8200000 42 8
-
-                                       /* IDSEL 0x18 */
-                                        c000 0 0 1 f8200000 42 8
-                                        c000 0 0 2 f8200000 43 8
-                                        c000 0 0 3 f8200000 40 8
-                                        c000 0 0 4 f8200000 41 8>;
-			interrupt-parent = <&Cpm_pic>;
-                       interrupts = <14 8>;
-                       bus-range = <0 0>;
-                       ranges = <02000000 0 80000000 80000000 0 40000000
-                                 01000000 0 00000000 f6000000 0 02000000>;
-               };
+	model = "MPC8272ADS";
+	compatible = "fsl,mpc8272ads";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8272@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <d#32>;
+			i-cache-line-size = <d#32>;
+			d-cache-size = <d#16384>;
+			i-cache-size = <d#16384>;
+			timebase-frequency = <0>;
+			bus-frequency = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	localbus@f0010100 {
+		compatible = "fsl,mpc8272-localbus",
+		             "fsl,pq2-localbus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <f0010100 40>;
+
+		ranges = <0 0 fe000000 02000000
+		          1 0 f4500000 00008000
+		          3 0 f8200000 00008000>;
+
+		flash@0,0 {
+			compatible = "jedec-flash";
+			reg = <0 0 2000000>;
+			bank-width = <4>;
+			device-width = <1>;
+		};
+
+		board-control@1,0 {
+			reg = <1 0 20>;
+			compatible = "fsl,mpc8272ads-bcsr";
+		};
+
+		PCI_PIC: interrupt-controller@3,0 {
+			compatible = "fsl,mpc8272ads-pci-pic",
+			             "fsl,pq2ads-pci-pic";
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			reg = <3 0 8>;
+			interrupt-parent = <&PIC>;
+			interrupts = <14 8>;
+		};
+	};
+
+
+	pci@f0010800 {
+		device_type = "pci";
+		reg = <f0010800 10c f00101ac 8 f00101c4 8>;
+		compatible = "fsl,mpc8272-pci", "fsl,pq2-pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		clock-frequency = <d#66666666>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+		                 /* IDSEL 0x16 */
+		                 b000 0 0 1 &PCI_PIC 0
+		                 b000 0 0 2 &PCI_PIC 1
+		                 b000 0 0 3 &PCI_PIC 2
+		                 b000 0 0 4 &PCI_PIC 3
+
+		                 /* IDSEL 0x17 */
+		                 b800 0 0 1 &PCI_PIC 4
+		                 b800 0 0 2 &PCI_PIC 5
+		                 b800 0 0 3 &PCI_PIC 6
+		                 b800 0 0 4 &PCI_PIC 7
+
+		                 /* IDSEL 0x18 */
+		                 c000 0 0 1 &PCI_PIC 8
+		                 c000 0 0 2 &PCI_PIC 9
+		                 c000 0 0 3 &PCI_PIC a
+		                 c000 0 0 4 &PCI_PIC b>;
+
+		interrupt-parent = <&PIC>;
+		interrupts = <12 8>;
+		ranges = <42000000 0 80000000 80000000 0 20000000
+		          02000000 0 a0000000 a0000000 0 20000000
+		          01000000 0 00000000 f6000000 0 02000000>;
+	};
+
+	soc@f0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,mpc8272", "fsl,pq2-soc";
+		ranges = <00000000 f0000000 00053000>;
+
+		// Temporary -- will go away once kernel uses ranges for get_immrbase().
+		reg = <f0000000 00053000>;
+
+		cpm@119c0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
+			reg = <119c0 30>;
+			ranges;
+
+			muram@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0 10000>;
+
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0 2000 9800 800>;
+				};
+			};
+
+			brg@119f0 {
+				compatible = "fsl,mpc8272-brg",
+				             "fsl,cpm2-brg",
+				             "fsl,cpm-brg";
+				reg = <119f0 10 115f0 10>;
+			};
+
+			serial@11a00 {
+				device_type = "serial";
+				compatible = "fsl,mpc8272-scc-uart",
+				             "fsl,cpm2-scc-uart";
+				reg = <11a00 20 8000 100>;
+				interrupts = <28 8>;
+				interrupt-parent = <&PIC>;
+				fsl,cpm-brg = <1>;
+				fsl,cpm-command = <00800000>;
+			};
+
+			serial@11a60 {
+				device_type = "serial";
+				compatible = "fsl,mpc8272-scc-uart",
+				             "fsl,cpm2-scc-uart";
+				reg = <11a60 20 8300 100>;
+				interrupts = <2b 8>;
+				interrupt-parent = <&PIC>;
+				fsl,cpm-brg = <4>;
+				fsl,cpm-command = <0ce00000>;
+			};
+
+			mdio@10d40 {
+				device_type = "mdio";
+				compatible = "fsl,mpc8272ads-mdio-bitbang",
+				             "fsl,mpc8272-mdio-bitbang",
+				             "fsl,cpm2-mdio-bitbang";
+				reg = <10d40 14>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				fsl,mdio-pin = <12>;
+				fsl,mdc-pin = <13>;
+
+				PHY0: ethernet-phy@0 {
+					interrupt-parent = <&PIC>;
+					interrupts = <17 8>;
+					reg = <0>;
+					device_type = "ethernet-phy";
+				};
+
+				PHY1: ethernet-phy@1 {
+					interrupt-parent = <&PIC>;
+					interrupts = <17 8>;
+					reg = <3>;
+					device_type = "ethernet-phy";
+				};
+			};
+
+			ethernet@11300 {
+				device_type = "network";
+				compatible = "fsl,mpc8272-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <11300 20 8400 100 11390 1>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+				interrupts = <20 8>;
+				interrupt-parent = <&PIC>;
+				phy-handle = <&PHY0>;
+				linux,network-index = <0>;
+				fsl,cpm-command = <12000300>;
+			};
+
+			ethernet@11320 {
+				device_type = "network";
+				compatible = "fsl,mpc8272-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <11320 20 8500 100 113b0 1>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+				interrupts = <21 8>;
+				interrupt-parent = <&PIC>;
+				phy-handle = <&PHY1>;
+				linux,network-index = <1>;
+				fsl,cpm-command = <16200300>;
+			};
+		};
+
+		PIC: interrupt-controller@10c00 {
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			reg = <10c00 80>;
+			compatible = "fsl,mpc8272-pic", "fsl,cpm2-pic";
+		};
 
 /* May need to remove if on a part without crypto engine */
-               crypto@30000 {
-                       device_type = "crypto";
-                       model = "SEC2";
-                       compatible = "talitos";
-                       reg = <30000 10000>;
-                       interrupts = <b 2>;
-			interrupt-parent = <&Cpm_pic>;
-                       num-channels = <4>;
-                       channel-fifo-len = <18>;
-                       exec-units-mask = <0000007e>;
+		crypto@30000 {
+			device_type = "crypto";
+			model = "SEC2";
+			compatible = "fsl,mpc8272-talitos-sec2",
+			             "fsl,talitos-sec2",
+			             "fsl,talitos",
+			             "talitos";
+			reg = <30000 10000>;
+			interrupts = <b 8>;
+			interrupt-parent = <&PIC>;
+			num-channels = <4>;
+			channel-fifo-len = <18>;
+			exec-units-mask = <0000007e>;
 /* desc mask is for rev1.x, we need runtime fixup for >=2.x */
-                       descriptor-types-mask = <01010ebf>;
-               };
+			descriptor-types-mask = <01010ebf>;
+		};
+	};
 
-       };
+	chosen {
+		linux,stdout-path = "/soc/cpm/serial@11a00";
+	};
 };

arch/powerpc/boot/dts/mpc8313erdb.dts

@@ -29,7 +29,6 @@
 			timebase-frequency = <0>;	// from bootloader
 			bus-frequency = <0>;		// from bootloader
 			clock-frequency = <0>;		// from bootloader
-			32-bit;
 		};
 	};
 
@@ -41,7 +40,6 @@
 	soc8313@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -73,11 +71,11 @@
 
 		spi@7000 {
 			device_type = "spi";
-			compatible = "mpc83xx_spi";
+			compatible = "fsl_spi";
 			reg = <7000 1000>;
 			interrupts = <10 8>;
 			interrupt-parent = < &ipic >;
-			mode = <0>;
+			mode = "cpu";
 		};
 
 		/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
@@ -152,36 +150,6 @@
 			interrupt-parent = < &ipic >;
 		};
 
-		pci@8500 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-					/* IDSEL 0x0E -mini PCI */
-					 7000 0 0 1 &ipic 12 8
-					 7000 0 0 2 &ipic 12 8
-					 7000 0 0 3 &ipic 12 8
-					 7000 0 0 4 &ipic 12 8
-
-					/* IDSEL 0x0F - PCI slot */
-					 7800 0 0 1 &ipic 11 8
-					 7800 0 0 2 &ipic 12 8
-					 7800 0 0 3 &ipic 11 8
-					 7800 0 0 4 &ipic 12 8>;
-			interrupt-parent = < &ipic >;
-			interrupts = <42 8>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 90000000 90000000 0 10000000
-			          42000000 0 80000000 80000000 0 10000000
-			          01000000 0 00000000 e2000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8500 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
 		crypto@30000 {
 			device_type = "crypto";
 			model = "SEC2";
@@ -207,8 +175,37 @@
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <700 100>;
-			built-in;
 			device_type = "ipic";
 		};
 	};
+
+	pci@e0008500 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+				/* IDSEL 0x0E -mini PCI */
+				 7000 0 0 1 &ipic 12 8
+				 7000 0 0 2 &ipic 12 8
+				 7000 0 0 3 &ipic 12 8
+				 7000 0 0 4 &ipic 12 8
+
+				/* IDSEL 0x0F - PCI slot */
+				 7800 0 0 1 &ipic 11 8
+				 7800 0 0 2 &ipic 12 8
+				 7800 0 0 3 &ipic 11 8
+				 7800 0 0 4 &ipic 12 8>;
+		interrupt-parent = < &ipic >;
+		interrupts = <42 8>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 90000000 90000000 0 10000000
+			  42000000 0 80000000 80000000 0 10000000
+			  01000000 0 00000000 e2000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008500 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
 };

arch/powerpc/boot/dts/mpc832x_mds.dts

@@ -29,7 +29,6 @@
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
-			32-bit;
 		};
 	};
 
@@ -46,7 +45,6 @@
 	soc8323@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -99,71 +97,11 @@
 			descriptor-types-mask = <0122003f>;
 		};
 
-		pci@8500 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-					/* IDSEL 0x11 AD17 */
-					 8800 0 0 1 &ipic 14 8
-					 8800 0 0 2 &ipic 15 8
-					 8800 0 0 3 &ipic 16 8
-					 8800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x12 AD18 */
-					 9000 0 0 1 &ipic 16 8
-					 9000 0 0 2 &ipic 17 8
-					 9000 0 0 3 &ipic 14 8
-					 9000 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x13 AD19 */
-					 9800 0 0 1 &ipic 17 8
-					 9800 0 0 2 &ipic 14 8
-					 9800 0 0 3 &ipic 15 8
-					 9800 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x15 AD21*/
-					 a800 0 0 1 &ipic 14 8
-					 a800 0 0 2 &ipic 15 8
-					 a800 0 0 3 &ipic 16 8
-					 a800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x16 AD22*/
-					 b000 0 0 1 &ipic 17 8
-					 b000 0 0 2 &ipic 14 8
-					 b000 0 0 3 &ipic 15 8
-					 b000 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x17 AD23*/
-					 b800 0 0 1 &ipic 16 8
-					 b800 0 0 2 &ipic 17 8
-					 b800 0 0 3 &ipic 14 8
-					 b800 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x18 AD24*/
-					 c000 0 0 1 &ipic 15 8
-					 c000 0 0 2 &ipic 16 8
-					 c000 0 0 3 &ipic 17 8
-					 c000 0 0 4 &ipic 14 8>;
-			interrupt-parent = < &ipic >;
-			interrupts = <42 8>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 90000000 90000000 0 10000000
-			          42000000 0 80000000 80000000 0 10000000
-			          01000000 0 00000000 d0000000 0 00100000>;
-			clock-frequency = <0>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8500 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
 		ipic: pic@700 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <700 100>;
-			built-in;
 			device_type = "ipic";
 		};
 		
@@ -333,10 +271,68 @@
 			#address-cells = <0>;
 			#interrupt-cells = <1>;
 			reg = <80 80>;
-			built-in;
 			big-endian;
 			interrupts = <20 8 21 8>; //high:32 low:33
 			interrupt-parent = < &ipic >;
 		};
 	};
+
+	pci@e0008500 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+				/* IDSEL 0x11 AD17 */
+				 8800 0 0 1 &ipic 14 8
+				 8800 0 0 2 &ipic 15 8
+				 8800 0 0 3 &ipic 16 8
+				 8800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x12 AD18 */
+				 9000 0 0 1 &ipic 16 8
+				 9000 0 0 2 &ipic 17 8
+				 9000 0 0 3 &ipic 14 8
+				 9000 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x13 AD19 */
+				 9800 0 0 1 &ipic 17 8
+				 9800 0 0 2 &ipic 14 8
+				 9800 0 0 3 &ipic 15 8
+				 9800 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x15 AD21*/
+				 a800 0 0 1 &ipic 14 8
+				 a800 0 0 2 &ipic 15 8
+				 a800 0 0 3 &ipic 16 8
+				 a800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x16 AD22*/
+				 b000 0 0 1 &ipic 17 8
+				 b000 0 0 2 &ipic 14 8
+				 b000 0 0 3 &ipic 15 8
+				 b000 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x17 AD23*/
+				 b800 0 0 1 &ipic 16 8
+				 b800 0 0 2 &ipic 17 8
+				 b800 0 0 3 &ipic 14 8
+				 b800 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x18 AD24*/
+				 c000 0 0 1 &ipic 15 8
+				 c000 0 0 2 &ipic 16 8
+				 c000 0 0 3 &ipic 17 8
+				 c000 0 0 4 &ipic 14 8>;
+		interrupt-parent = < &ipic >;
+		interrupts = <42 8>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 90000000 90000000 0 10000000
+			  42000000 0 80000000 80000000 0 10000000
+			  01000000 0 00000000 d0000000 0 00100000>;
+		clock-frequency = <0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008500 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
 };

arch/powerpc/boot/dts/mpc832x_rdb.dts

@@ -29,7 +29,6 @@
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
-			32-bit;
 		};
 	};
 
@@ -41,7 +40,6 @@
 	soc8323@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -94,45 +92,11 @@
 			descriptor-types-mask = <0122003f>;
 		};
 
-		pci@8500 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-					/* IDSEL 0x10 AD16 (USB) */
-					 8000 0 0 1 &pic 11 8
-
-					/* IDSEL 0x11 AD17 (Mini1)*/
-					 8800 0 0 1 &pic 12 8
-					 8800 0 0 2 &pic 13 8
-					 8800 0 0 3 &pic 14 8
-					 8800 0 0 4 &pic 30 8
-
-					/* IDSEL 0x12 AD18 (PCI/Mini2) */
-					 9000 0 0 1 &pic 13 8
-					 9000 0 0 2 &pic 14 8
-					 9000 0 0 3 &pic 30 8
-					 9000 0 0 4 &pic 11 8>;
-
-			interrupt-parent = <&pic>;
-			interrupts = <42 8>;
-			bus-range = <0 0>;
-			ranges = <42000000 0 80000000 80000000 0 10000000
-			          02000000 0 90000000 90000000 0 10000000
-			          01000000 0 d0000000 d0000000 0 04000000>;
-			clock-frequency = <0>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8500 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
 		pic:pic@700 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <700 100>;
-			built-in;
 			device_type = "ipic";
 		};
 
@@ -211,7 +175,7 @@
 			reg = <4c0 40>;
 			interrupts = <2>;
 			interrupt-parent = <&qeic>;
-			mode = "cpu";
+			mode = "cpu-qe";
 		};
 
 		spi@500 {
@@ -292,10 +256,42 @@
 			#address-cells = <0>;
 			#interrupt-cells = <1>;
 			reg = <80 80>;
-			built-in;
 			big-endian;
 			interrupts = <20 8 21 8>; //high:32 low:33
 			interrupt-parent = <&pic>;
 		};
 	};
+
+	pci@e0008500 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+				/* IDSEL 0x10 AD16 (USB) */
+				 8000 0 0 1 &pic 11 8
+
+				/* IDSEL 0x11 AD17 (Mini1)*/
+				 8800 0 0 1 &pic 12 8
+				 8800 0 0 2 &pic 13 8
+				 8800 0 0 3 &pic 14 8
+				 8800 0 0 4 &pic 30 8
+
+				/* IDSEL 0x12 AD18 (PCI/Mini2) */
+				 9000 0 0 1 &pic 13 8
+				 9000 0 0 2 &pic 14 8
+				 9000 0 0 3 &pic 30 8
+				 9000 0 0 4 &pic 11 8>;
+
+		interrupt-parent = <&pic>;
+		interrupts = <42 8>;
+		bus-range = <0 0>;
+		ranges = <42000000 0 80000000 80000000 0 10000000
+			  02000000 0 90000000 90000000 0 10000000
+			  01000000 0 d0000000 d0000000 0 04000000>;
+		clock-frequency = <0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008500 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
 };

arch/powerpc/boot/dts/mpc8349emitx.dts

@@ -28,7 +28,6 @@
 			timebase-frequency = <0>;	// from bootloader
 			bus-frequency = <0>;		// from bootloader
 			clock-frequency = <0>;		// from bootloader
-			32-bit;
 		};
 	};
 
@@ -40,7 +39,6 @@
 	soc8349@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -72,11 +70,11 @@
 
 		spi@7000 {
 			device_type = "spi";
-			compatible = "mpc83xx_spi";
+			compatible = "fsl_spi";
 			reg = <7000 1000>;
 			interrupts = <10 8>;
 			interrupt-parent = < &ipic >;
-			mode = <0>;
+			mode = "cpu";
 		};
 
 		usb@22000 {
@@ -142,6 +140,7 @@
 			interrupts = <20 8 21 8 22 8>;
 			interrupt-parent = < &ipic >;
 			phy-handle = < &phy1c >;
+			linux,network-index = <0>;
 		};
 
 		ethernet@25000 {
@@ -161,6 +160,7 @@
 			interrupts = <23 8 24 8 25 8>;
 			interrupt-parent = < &ipic >;
 			phy-handle = < &phy1f >;
+			linux,network-index = <1>;
 		};
 
 		serial@4500 {
@@ -181,52 +181,6 @@
 			interrupt-parent = < &ipic >;
 		};
 
-		pci@8500 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-					/* IDSEL 0x10 - SATA */
-					8000 0 0 1 &ipic 16 8 /* SATA_INTA */
-					>;
-			interrupt-parent = < &ipic >;
-			interrupts = <42 8>;
-			bus-range = <0 0>;
-			ranges = <42000000 0 80000000 80000000 0 10000000
-				  02000000 0 90000000 90000000 0 10000000
-				  01000000 0 00000000 e2000000 0 01000000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8500 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
-		pci@8600 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-					/* IDSEL 0x0E - MiniPCI Slot */
-					7000 0 0 1 &ipic 15 8 /* PCI_INTA */
-
-					/* IDSEL 0x0F - PCI Slot */
-					7800 0 0 1 &ipic 14 8 /* PCI_INTA */
-					7800 0 0 2 &ipic 15 8 /* PCI_INTB */
-					 >;
-			interrupt-parent = < &ipic >;
-			interrupts = <43 8>;
-			bus-range = <1 1>;
-			ranges = <42000000 0 a0000000 a0000000 0 10000000
-				  02000000 0 b0000000 b0000000 0 10000000
-				  01000000 0 00000000 e3000000 0 01000000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8600 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
 		crypto@30000 {
 			device_type = "crypto";
 			model = "SEC2";
@@ -245,8 +199,56 @@
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <700 100>;
-			built-in;
 			device_type = "ipic";
 		};
 	};
+
+	pci@e0008500 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+				/* IDSEL 0x10 - SATA */
+				8000 0 0 1 &ipic 16 8 /* SATA_INTA */
+				>;
+		interrupt-parent = < &ipic >;
+		interrupts = <42 8>;
+		bus-range = <0 0>;
+		ranges = <42000000 0 80000000 80000000 0 10000000
+			  02000000 0 90000000 90000000 0 10000000
+			  01000000 0 00000000 e2000000 0 01000000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008500 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
+
+	pci@e0008600 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+				/* IDSEL 0x0E - MiniPCI Slot */
+				7000 0 0 1 &ipic 15 8 /* PCI_INTA */
+
+				/* IDSEL 0x0F - PCI Slot */
+				7800 0 0 1 &ipic 14 8 /* PCI_INTA */
+				7800 0 0 2 &ipic 15 8 /* PCI_INTB */
+				 >;
+		interrupt-parent = < &ipic >;
+		interrupts = <43 8>;
+		bus-range = <0 0>;
+		ranges = <42000000 0 a0000000 a0000000 0 10000000
+			  02000000 0 b0000000 b0000000 0 10000000
+			  01000000 0 00000000 e3000000 0 01000000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008600 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
+
+
+
 };

arch/powerpc/boot/dts/mpc8349emitxgp.dts

@@ -28,7 +28,6 @@
 			timebase-frequency = <0>;	// from bootloader
 			bus-frequency = <0>;		// from bootloader
 			clock-frequency = <0>;		// from bootloader
-			32-bit;
 		};
 	};
 
@@ -40,7 +39,6 @@
 	soc8349@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -72,11 +70,11 @@
 
 		spi@7000 {
 			device_type = "spi";
-			compatible = "mpc83xx_spi";
+			compatible = "fsl_spi";
 			reg = <7000 1000>;
 			interrupts = <10 8>;
 			interrupt-parent = < &ipic >;
-			mode = <0>;
+			mode = "cpu";
 		};
 
 		usb@23000 {
@@ -116,6 +114,7 @@
 			interrupts = <20 8 21 8 22 8>;
 			interrupt-parent = < &ipic >;
 			phy-handle = < &phy1c >;
+			linux,network-index = <0>;
 		};
 
 		serial@4500 {
@@ -136,28 +135,6 @@
 			interrupt-parent = < &ipic >;
 		};
 
-		pci@8600 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-					/* IDSEL 0x0F - PCI Slot */
-					7800 0 0 1 &ipic 14 8 /* PCI_INTA */
-					7800 0 0 2 &ipic 15 8 /* PCI_INTB */
-					 >;
-			interrupt-parent = < &ipic >;
-			interrupts = <43 8>;
-			bus-range = <1 1>;
-			ranges = <42000000 0 a0000000 a0000000 0 10000000
-				  02000000 0 b0000000 b0000000 0 10000000
-				  01000000 0 00000000 e3000000 0 01000000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8600 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
 		crypto@30000 {
 			device_type = "crypto";
 			model = "SEC2";
@@ -176,8 +153,29 @@
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <700 100>;
-			built-in;
 			device_type = "ipic";
 		};
 	};
+
+	pci@e0008600 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+				/* IDSEL 0x0F - PCI Slot */
+				7800 0 0 1 &ipic 14 8 /* PCI_INTA */
+				7800 0 0 2 &ipic 15 8 /* PCI_INTB */
+				 >;
+		interrupt-parent = < &ipic >;
+		interrupts = <43 8>;
+		bus-range = <1 1>;
+		ranges = <42000000 0 a0000000 a0000000 0 10000000
+			  02000000 0 b0000000 b0000000 0 10000000
+			  01000000 0 00000000 e3000000 0 01000000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008600 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
 };

arch/powerpc/boot/dts/mpc834x_mds.dts

@@ -29,7 +29,6 @@
 			timebase-frequency = <0>;	// from bootloader
 			bus-frequency = <0>;		// from bootloader
 			clock-frequency = <0>;		// from bootloader
-			32-bit;
 		};
 	};
 
@@ -46,7 +45,6 @@
 	soc8349@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -78,11 +76,11 @@
 
 		spi@7000 {
 			device_type = "spi";
-			compatible = "mpc83xx_spi";
+			compatible = "fsl_spi";
 			reg = <7000 1000>;
 			interrupts = <10 8>;
 			interrupt-parent = < &ipic >;
-			mode = <0>;
+			mode = "cpu";
 		};
 
 		/* phy type (ULPI or SERIAL) are only types supportted for MPH */
@@ -146,6 +144,7 @@
 			interrupts = <20 8 21 8 22 8>;
 			interrupt-parent = < &ipic >;
 			phy-handle = < &phy0 >;
+			linux,network-index = <0>;
 		};
 
 		ethernet@25000 {
@@ -165,6 +164,7 @@
 			interrupts = <23 8 24 8 25 8>;
 			interrupt-parent = < &ipic >;
 			phy-handle = < &phy1 >;
+			linux,network-index = <1>;
 		};
 
 		serial@4500 {
@@ -185,126 +185,6 @@
 			interrupt-parent = < &ipic >;
 		};
 
-		pci@8500 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-					/* IDSEL 0x11 */
-					 8800 0 0 1 &ipic 14 8
-					 8800 0 0 2 &ipic 15 8
-					 8800 0 0 3 &ipic 16 8
-					 8800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x12 */
-					 9000 0 0 1 &ipic 16 8
-					 9000 0 0 2 &ipic 17 8
-					 9000 0 0 3 &ipic 14 8
-					 9000 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x13 */
-					 9800 0 0 1 &ipic 17 8
-					 9800 0 0 2 &ipic 14 8
-					 9800 0 0 3 &ipic 15 8
-					 9800 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x15 */
-					 a800 0 0 1 &ipic 14 8
-					 a800 0 0 2 &ipic 15 8
-					 a800 0 0 3 &ipic 16 8
-					 a800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x16 */
-					 b000 0 0 1 &ipic 17 8
-					 b000 0 0 2 &ipic 14 8
-					 b000 0 0 3 &ipic 15 8
-					 b000 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x17 */
-					 b800 0 0 1 &ipic 16 8
-					 b800 0 0 2 &ipic 17 8
-					 b800 0 0 3 &ipic 14 8
-					 b800 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x18 */
-					 c000 0 0 1 &ipic 15 8
-					 c000 0 0 2 &ipic 16 8
-					 c000 0 0 3 &ipic 17 8
-					 c000 0 0 4 &ipic 14 8>;
-			interrupt-parent = < &ipic >;
-			interrupts = <42 8>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 90000000 90000000 0 10000000
-				  42000000 0 80000000 80000000 0 10000000
-				  01000000 0 00000000 e2000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8500 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
-		pci@8600 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-					/* IDSEL 0x11 */
-					 8800 0 0 1 &ipic 14 8
-					 8800 0 0 2 &ipic 15 8
-					 8800 0 0 3 &ipic 16 8
-					 8800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x12 */
-					 9000 0 0 1 &ipic 16 8
-					 9000 0 0 2 &ipic 17 8
-					 9000 0 0 3 &ipic 14 8
-					 9000 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x13 */
-					 9800 0 0 1 &ipic 17 8
-					 9800 0 0 2 &ipic 14 8
-					 9800 0 0 3 &ipic 15 8
-					 9800 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x15 */
-					 a800 0 0 1 &ipic 14 8
-					 a800 0 0 2 &ipic 15 8
-					 a800 0 0 3 &ipic 16 8
-					 a800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x16 */
-					 b000 0 0 1 &ipic 17 8
-					 b000 0 0 2 &ipic 14 8
-					 b000 0 0 3 &ipic 15 8
-					 b000 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x17 */
-					 b800 0 0 1 &ipic 16 8
-					 b800 0 0 2 &ipic 17 8
-					 b800 0 0 3 &ipic 14 8
-					 b800 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x18 */
-					 c000 0 0 1 &ipic 15 8
-					 c000 0 0 2 &ipic 16 8
-					 c000 0 0 3 &ipic 17 8
-					 c000 0 0 4 &ipic 14 8>;
-			interrupt-parent = < &ipic >;
-			interrupts = <42 8>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 b0000000 b0000000 0 10000000
-				  42000000 0 a0000000 a0000000 0 10000000
-				  01000000 0 00000000 e2100000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8600 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
 		/* May need to remove if on a part without crypto engine */
 		crypto@30000 {
 			device_type = "crypto";
@@ -332,8 +212,127 @@
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <700 100>;
-			built-in;
 			device_type = "ipic";
 		};
 	};
+
+	pci@e0008500 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+				/* IDSEL 0x11 */
+				 8800 0 0 1 &ipic 14 8
+				 8800 0 0 2 &ipic 15 8
+				 8800 0 0 3 &ipic 16 8
+				 8800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x12 */
+				 9000 0 0 1 &ipic 16 8
+				 9000 0 0 2 &ipic 17 8
+				 9000 0 0 3 &ipic 14 8
+				 9000 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x13 */
+				 9800 0 0 1 &ipic 17 8
+				 9800 0 0 2 &ipic 14 8
+				 9800 0 0 3 &ipic 15 8
+				 9800 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x15 */
+				 a800 0 0 1 &ipic 14 8
+				 a800 0 0 2 &ipic 15 8
+				 a800 0 0 3 &ipic 16 8
+				 a800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x16 */
+				 b000 0 0 1 &ipic 17 8
+				 b000 0 0 2 &ipic 14 8
+				 b000 0 0 3 &ipic 15 8
+				 b000 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x17 */
+				 b800 0 0 1 &ipic 16 8
+				 b800 0 0 2 &ipic 17 8
+				 b800 0 0 3 &ipic 14 8
+				 b800 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x18 */
+				 c000 0 0 1 &ipic 15 8
+				 c000 0 0 2 &ipic 16 8
+				 c000 0 0 3 &ipic 17 8
+				 c000 0 0 4 &ipic 14 8>;
+		interrupt-parent = < &ipic >;
+		interrupts = <42 8>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 90000000 90000000 0 10000000
+			  42000000 0 80000000 80000000 0 10000000
+			  01000000 0 00000000 e2000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008500 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
+
+	pci@e0008600 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+				/* IDSEL 0x11 */
+				 8800 0 0 1 &ipic 14 8
+				 8800 0 0 2 &ipic 15 8
+				 8800 0 0 3 &ipic 16 8
+				 8800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x12 */
+				 9000 0 0 1 &ipic 16 8
+				 9000 0 0 2 &ipic 17 8
+				 9000 0 0 3 &ipic 14 8
+				 9000 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x13 */
+				 9800 0 0 1 &ipic 17 8
+				 9800 0 0 2 &ipic 14 8
+				 9800 0 0 3 &ipic 15 8
+				 9800 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x15 */
+				 a800 0 0 1 &ipic 14 8
+				 a800 0 0 2 &ipic 15 8
+				 a800 0 0 3 &ipic 16 8
+				 a800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x16 */
+				 b000 0 0 1 &ipic 17 8
+				 b000 0 0 2 &ipic 14 8
+				 b000 0 0 3 &ipic 15 8
+				 b000 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x17 */
+				 b800 0 0 1 &ipic 16 8
+				 b800 0 0 2 &ipic 17 8
+				 b800 0 0 3 &ipic 14 8
+				 b800 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x18 */
+				 c000 0 0 1 &ipic 15 8
+				 c000 0 0 2 &ipic 16 8
+				 c000 0 0 3 &ipic 17 8
+				 c000 0 0 4 &ipic 14 8>;
+		interrupt-parent = < &ipic >;
+		interrupts = <42 8>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 b0000000 b0000000 0 10000000
+			  42000000 0 a0000000 a0000000 0 10000000
+			  01000000 0 00000000 e2100000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008600 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
+	};
 };

arch/powerpc/boot/dts/mpc836x_mds.dts

@@ -34,7 +34,6 @@
 			timebase-frequency = <3EF1480>;
 			bus-frequency = <FBC5200>;
 			clock-frequency = <1F78A400>;
-			32-bit;
 		};
 	};
 
@@ -51,7 +50,6 @@
 	soc8360@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -113,72 +111,11 @@
 			descriptor-types-mask = <01010ebf>;
 		};
 
-		pci@8500 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-					/* IDSEL 0x11 AD17 */
-					 8800 0 0 1 &ipic 14 8
-					 8800 0 0 2 &ipic 15 8
-					 8800 0 0 3 &ipic 16 8
-					 8800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x12 AD18 */
-					 9000 0 0 1 &ipic 16 8
-					 9000 0 0 2 &ipic 17 8
-					 9000 0 0 3 &ipic 14 8
-					 9000 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x13 AD19 */
-					 9800 0 0 1 &ipic 17 8
-					 9800 0 0 2 &ipic 14 8
-					 9800 0 0 3 &ipic 15 8
-					 9800 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x15 AD21*/
-					 a800 0 0 1 &ipic 14 8
-					 a800 0 0 2 &ipic 15 8
-					 a800 0 0 3 &ipic 16 8
-					 a800 0 0 4 &ipic 17 8
-
-					/* IDSEL 0x16 AD22*/
-					 b000 0 0 1 &ipic 17 8
-					 b000 0 0 2 &ipic 14 8
-					 b000 0 0 3 &ipic 15 8
-					 b000 0 0 4 &ipic 16 8
-
-					/* IDSEL 0x17 AD23*/
-					 b800 0 0 1 &ipic 16 8
-					 b800 0 0 2 &ipic 17 8
-					 b800 0 0 3 &ipic 14 8
-					 b800 0 0 4 &ipic 15 8
-
-					/* IDSEL 0x18 AD24*/
-					 c000 0 0 1 &ipic 15 8
-					 c000 0 0 2 &ipic 16 8
-					 c000 0 0 3 &ipic 17 8
-					 c000 0 0 4 &ipic 14 8>;
-			interrupt-parent = < &ipic >;
-			interrupts = <42 8>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 a0000000 a0000000 0 10000000
-				  42000000 0 80000000 80000000 0 10000000
-				  01000000 0 00000000 e2000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8500 100>;
-			compatible = "fsl,mpc8349-pci";
-			device_type = "pci";
-		};
-
 		ipic: pic@700 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <700 100>;
-			built-in;
 			device_type = "ipic";
 		};
 
@@ -364,11 +301,69 @@
 			#address-cells = <0>;
 			#interrupt-cells = <1>;
 			reg = <80 80>;
-			built-in;
 			big-endian;
 			interrupts = <20 8 21 8>; //high:32 low:33
 			interrupt-parent = < &ipic >;
 		};
+	};
 
+	pci@e0008500 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+				/* IDSEL 0x11 AD17 */
+				 8800 0 0 1 &ipic 14 8
+				 8800 0 0 2 &ipic 15 8
+				 8800 0 0 3 &ipic 16 8
+				 8800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x12 AD18 */
+				 9000 0 0 1 &ipic 16 8
+				 9000 0 0 2 &ipic 17 8
+				 9000 0 0 3 &ipic 14 8
+				 9000 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x13 AD19 */
+				 9800 0 0 1 &ipic 17 8
+				 9800 0 0 2 &ipic 14 8
+				 9800 0 0 3 &ipic 15 8
+				 9800 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x15 AD21*/
+				 a800 0 0 1 &ipic 14 8
+				 a800 0 0 2 &ipic 15 8
+				 a800 0 0 3 &ipic 16 8
+				 a800 0 0 4 &ipic 17 8
+
+				/* IDSEL 0x16 AD22*/
+				 b000 0 0 1 &ipic 17 8
+				 b000 0 0 2 &ipic 14 8
+				 b000 0 0 3 &ipic 15 8
+				 b000 0 0 4 &ipic 16 8
+
+				/* IDSEL 0x17 AD23*/
+				 b800 0 0 1 &ipic 16 8
+				 b800 0 0 2 &ipic 17 8
+				 b800 0 0 3 &ipic 14 8
+				 b800 0 0 4 &ipic 15 8
+
+				/* IDSEL 0x18 AD24*/
+				 c000 0 0 1 &ipic 15 8
+				 c000 0 0 2 &ipic 16 8
+				 c000 0 0 3 &ipic 17 8
+				 c000 0 0 4 &ipic 14 8>;
+		interrupt-parent = < &ipic >;
+		interrupts = <42 8>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 a0000000 a0000000 0 10000000
+			  42000000 0 80000000 80000000 0 10000000
+			  01000000 0 00000000 e2000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008500 100>;
+		compatible = "fsl,mpc8349-pci";
+		device_type = "pci";
 	};
 };

arch/powerpc/boot/dts/mpc8540ads.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <0>;	//  33 MHz, from uboot
 			bus-frequency = <0>;	// 166 MHz
 			clock-frequency = <0>;	// 825 MHz, from uboot
-			32-bit;
 		};
 	};
 
@@ -42,7 +41,6 @@
 	soc8540@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00100000>;	// CCSRBAR 1M
@@ -173,105 +171,104 @@
 			interrupts = <2a 2>;
 			interrupt-parent = <&mpic>;
 		};
-		pci@8000 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
+		mpic: pic@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+			big-endian;
+		};
+	};
 
-				/* IDSEL 0x02 */
-				1000 0 0 1 &mpic 1 1
-				1000 0 0 2 &mpic 2 1
-				1000 0 0 3 &mpic 3 1
-				1000 0 0 4 &mpic 4 1
+	pci@e0008000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
 
-				/* IDSEL 0x03 */
-				1800 0 0 1 &mpic 4 1
-				1800 0 0 2 &mpic 1 1
-				1800 0 0 3 &mpic 2 1
-				1800 0 0 4 &mpic 3 1
+			/* IDSEL 0x02 */
+			1000 0 0 1 &mpic 1 1
+			1000 0 0 2 &mpic 2 1
+			1000 0 0 3 &mpic 3 1
+			1000 0 0 4 &mpic 4 1
 
-				/* IDSEL 0x04 */
-				2000 0 0 1 &mpic 3 1
-				2000 0 0 2 &mpic 4 1
-				2000 0 0 3 &mpic 1 1
-				2000 0 0 4 &mpic 2 1
+			/* IDSEL 0x03 */
+			1800 0 0 1 &mpic 4 1
+			1800 0 0 2 &mpic 1 1
+			1800 0 0 3 &mpic 2 1
+			1800 0 0 4 &mpic 3 1
 
-				/* IDSEL 0x05 */
-				2800 0 0 1 &mpic 2 1
-				2800 0 0 2 &mpic 3 1
-				2800 0 0 3 &mpic 4 1
-				2800 0 0 4 &mpic 1 1
+			/* IDSEL 0x04 */
+			2000 0 0 1 &mpic 3 1
+			2000 0 0 2 &mpic 4 1
+			2000 0 0 3 &mpic 1 1
+			2000 0 0 4 &mpic 2 1
 
-				/* IDSEL 0x0c */
-				6000 0 0 1 &mpic 1 1
-				6000 0 0 2 &mpic 2 1
-				6000 0 0 3 &mpic 3 1
-				6000 0 0 4 &mpic 4 1
+			/* IDSEL 0x05 */
+			2800 0 0 1 &mpic 2 1
+			2800 0 0 2 &mpic 3 1
+			2800 0 0 3 &mpic 4 1
+			2800 0 0 4 &mpic 1 1
 
-				/* IDSEL 0x0d */
-				6800 0 0 1 &mpic 4 1
-				6800 0 0 2 &mpic 1 1
-				6800 0 0 3 &mpic 2 1
-				6800 0 0 4 &mpic 3 1
+			/* IDSEL 0x0c */
+			6000 0 0 1 &mpic 1 1
+			6000 0 0 2 &mpic 2 1
+			6000 0 0 3 &mpic 3 1
+			6000 0 0 4 &mpic 4 1
 
-				/* IDSEL 0x0e */
-				7000 0 0 1 &mpic 3 1
-				7000 0 0 2 &mpic 4 1
-				7000 0 0 3 &mpic 1 1
-				7000 0 0 4 &mpic 2 1
+			/* IDSEL 0x0d */
+			6800 0 0 1 &mpic 4 1
+			6800 0 0 2 &mpic 1 1
+			6800 0 0 3 &mpic 2 1
+			6800 0 0 4 &mpic 3 1
 
-				/* IDSEL 0x0f */
-				7800 0 0 1 &mpic 2 1
-				7800 0 0 2 &mpic 3 1
-				7800 0 0 3 &mpic 4 1
-				7800 0 0 4 &mpic 1 1
+			/* IDSEL 0x0e */
+			7000 0 0 1 &mpic 3 1
+			7000 0 0 2 &mpic 4 1
+			7000 0 0 3 &mpic 1 1
+			7000 0 0 4 &mpic 2 1
 
-				/* IDSEL 0x12 */
-				9000 0 0 1 &mpic 1 1
-				9000 0 0 2 &mpic 2 1
-				9000 0 0 3 &mpic 3 1
-				9000 0 0 4 &mpic 4 1
+			/* IDSEL 0x0f */
+			7800 0 0 1 &mpic 2 1
+			7800 0 0 2 &mpic 3 1
+			7800 0 0 3 &mpic 4 1
+			7800 0 0 4 &mpic 1 1
 
-				/* IDSEL 0x13 */
-				9800 0 0 1 &mpic 4 1
-				9800 0 0 2 &mpic 1 1
-				9800 0 0 3 &mpic 2 1
-				9800 0 0 4 &mpic 3 1
+			/* IDSEL 0x12 */
+			9000 0 0 1 &mpic 1 1
+			9000 0 0 2 &mpic 2 1
+			9000 0 0 3 &mpic 3 1
+			9000 0 0 4 &mpic 4 1
 
-				/* IDSEL 0x14 */
-				a000 0 0 1 &mpic 3 1
-				a000 0 0 2 &mpic 4 1
-				a000 0 0 3 &mpic 1 1
-				a000 0 0 4 &mpic 2 1
+			/* IDSEL 0x13 */
+			9800 0 0 1 &mpic 4 1
+			9800 0 0 2 &mpic 1 1
+			9800 0 0 3 &mpic 2 1
+			9800 0 0 4 &mpic 3 1
 
-				/* IDSEL 0x15 */
-				a800 0 0 1 &mpic 2 1
-				a800 0 0 2 &mpic 3 1
-				a800 0 0 3 &mpic 4 1
-				a800 0 0 4 &mpic 1 1>;
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 80000000 80000000 0 20000000
-				  01000000 0 00000000 e2000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8000 1000>;
-			compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
-			device_type = "pci";
-		};
+			/* IDSEL 0x14 */
+			a000 0 0 1 &mpic 3 1
+			a000 0 0 2 &mpic 4 1
+			a000 0 0 3 &mpic 1 1
+			a000 0 0 4 &mpic 2 1
 
-		mpic: pic@40000 {
-			clock-frequency = <0>;
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <2>;
-			reg = <40000 40000>;
-			built-in;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
-			big-endian;
-		};
+			/* IDSEL 0x15 */
+			a800 0 0 1 &mpic 2 1
+			a800 0 0 2 &mpic 3 1
+			a800 0 0 3 &mpic 4 1
+			a800 0 0 4 &mpic 1 1>;
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 e2000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008000 1000>;
+		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+		device_type = "pci";
 	};
 };

arch/powerpc/boot/dts/mpc8541cds.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <0>;	//  33 MHz, from uboot
 			bus-frequency = <0>;	// 166 MHz
 			clock-frequency = <0>;	// 825 MHz, from uboot
-			32-bit;
 		};
 	};
 
@@ -42,10 +41,9 @@
 	soc8541@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
-		reg = <e0000000 00100000>;	// CCSRBAR 1M
+		reg = <e0000000 00001000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
 
 		memory-controller@2000 {
@@ -137,113 +135,145 @@
 			interrupt-parent = <&mpic>;
 		};
 
-		pci1: pci@8000 {
-			interrupt-map-mask = <1f800 0 0 7>;
-			interrupt-map = <
-
-				/* IDSEL 0x10 */
-				08000 0 0 1 &mpic 0 1
-				08000 0 0 2 &mpic 1 1
-				08000 0 0 3 &mpic 2 1
-				08000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x11 */
-				08800 0 0 1 &mpic 0 1
-				08800 0 0 2 &mpic 1 1
-				08800 0 0 3 &mpic 2 1
-				08800 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x12 (Slot 1) */
-				09000 0 0 1 &mpic 0 1
-				09000 0 0 2 &mpic 1 1
-				09000 0 0 3 &mpic 2 1
-				09000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x13 (Slot 2) */
-				09800 0 0 1 &mpic 1 1
-				09800 0 0 2 &mpic 2 1
-				09800 0 0 3 &mpic 3 1
-				09800 0 0 4 &mpic 0 1
-
-				/* IDSEL 0x14 (Slot 3) */
-				0a000 0 0 1 &mpic 2 1
-				0a000 0 0 2 &mpic 3 1
-				0a000 0 0 3 &mpic 0 1
-				0a000 0 0 4 &mpic 1 1
-
-				/* IDSEL 0x15 (Slot 4) */
-				0a800 0 0 1 &mpic 3 1
-				0a800 0 0 2 &mpic 0 1
-				0a800 0 0 3 &mpic 1 1
-				0a800 0 0 4 &mpic 2 1
-
-				/* Bus 1 (Tundra Bridge) */
-				/* IDSEL 0x12 (ISA bridge) */
-				19000 0 0 1 &mpic 0 1
-				19000 0 0 2 &mpic 1 1
-				19000 0 0 3 &mpic 2 1
-				19000 0 0 4 &mpic 3 1>;
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 80000000 80000000 0 20000000
-				  01000000 0 00000000 e2000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8000 1000>;
-			compatible = "fsl,mpc8540-pci";
-			device_type = "pci";
-
-			i8259@19000 {
-				clock-frequency = <0>;
+		mpic: pic@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+                        big-endian;
+		};
+
+		cpm@919c0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,mpc8541-cpm", "fsl,cpm2";
+			reg = <919c0 30>;
+			ranges;
+
+			muram@80000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 80000 10000>;
+
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0 2000 9000 1000>;
+				};
+			};
+
+			brg@919f0 {
+				compatible = "fsl,mpc8541-brg",
+				             "fsl,cpm2-brg",
+				             "fsl,cpm-brg";
+				reg = <919f0 10 915f0 10>;
+			};
+
+			cpmpic: pic@90c00 {
 				interrupt-controller;
-				device_type = "interrupt-controller";
-				reg = <19000 0 0 0 1>;
 				#address-cells = <0>;
 				#interrupt-cells = <2>;
-				built-in;
-				compatible = "chrp,iic";
-				big-endian;
-				interrupts = <1>;
-				interrupt-parent = <&pci1>;
+				interrupts = <2e 2>;
+				interrupt-parent = <&mpic>;
+				reg = <90c00 80>;
+				compatible = "fsl,mpc8541-cpm-pic", "fsl,cpm2-pic";
 			};
 		};
+	};
 
-		pci@9000 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
+	pci1: pci@e0008000 {
+		interrupt-map-mask = <1f800 0 0 7>;
+		interrupt-map = <
 
-				/* IDSEL 0x15 */
-				a800 0 0 1 &mpic b 1
-				a800 0 0 2 &mpic b 1
-				a800 0 0 3 &mpic b 1
-				a800 0 0 4 &mpic b 1>;
-			interrupt-parent = <&mpic>;
-			interrupts = <19 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 a0000000 a0000000 0 20000000
-				  01000000 0 00000000 e3000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <9000 1000>;
-			compatible = "fsl,mpc8540-pci";
-			device_type = "pci";
-		};
+			/* IDSEL 0x10 */
+			08000 0 0 1 &mpic 0 1
+			08000 0 0 2 &mpic 1 1
+			08000 0 0 3 &mpic 2 1
+			08000 0 0 4 &mpic 3 1
 
-		mpic: pic@40000 {
-			clock-frequency = <0>;
+			/* IDSEL 0x11 */
+			08800 0 0 1 &mpic 0 1
+			08800 0 0 2 &mpic 1 1
+			08800 0 0 3 &mpic 2 1
+			08800 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x12 (Slot 1) */
+			09000 0 0 1 &mpic 0 1
+			09000 0 0 2 &mpic 1 1
+			09000 0 0 3 &mpic 2 1
+			09000 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x13 (Slot 2) */
+			09800 0 0 1 &mpic 1 1
+			09800 0 0 2 &mpic 2 1
+			09800 0 0 3 &mpic 3 1
+			09800 0 0 4 &mpic 0 1
+
+			/* IDSEL 0x14 (Slot 3) */
+			0a000 0 0 1 &mpic 2 1
+			0a000 0 0 2 &mpic 3 1
+			0a000 0 0 3 &mpic 0 1
+			0a000 0 0 4 &mpic 1 1
+
+			/* IDSEL 0x15 (Slot 4) */
+			0a800 0 0 1 &mpic 3 1
+			0a800 0 0 2 &mpic 0 1
+			0a800 0 0 3 &mpic 1 1
+			0a800 0 0 4 &mpic 2 1
+
+			/* Bus 1 (Tundra Bridge) */
+			/* IDSEL 0x12 (ISA bridge) */
+			19000 0 0 1 &mpic 0 1
+			19000 0 0 2 &mpic 1 1
+			19000 0 0 3 &mpic 2 1
+			19000 0 0 4 &mpic 3 1>;
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 e2000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008000 1000>;
+		compatible = "fsl,mpc8540-pci";
+		device_type = "pci";
+
+		i8259@19000 {
 			interrupt-controller;
+			device_type = "interrupt-controller";
+			reg = <19000 0 0 0 1>;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
-			reg = <40000 40000>;
-			built-in;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
-                        big-endian;
+			compatible = "chrp,iic";
+			interrupts = <1>;
+			interrupt-parent = <&pci1>;
 		};
 	};
+
+	pci@e0009000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+			/* IDSEL 0x15 */
+			a800 0 0 1 &mpic b 1
+			a800 0 0 2 &mpic b 1
+			a800 0 0 3 &mpic b 1
+			a800 0 0 4 &mpic b 1>;
+		interrupt-parent = <&mpic>;
+		interrupts = <19 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 a0000000 a0000000 0 20000000
+			  01000000 0 00000000 e3000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0009000 1000>;
+		compatible = "fsl,mpc8540-pci";
+		device_type = "pci";
+	};
 };

arch/powerpc/boot/dts/mpc8544ds.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
-			32-bit;
 		};
 	};
 
@@ -42,19 +41,9 @@
 	soc8544@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 
-
-		ranges = <00001000 e0001000 000ff000
-			  80000000 80000000 20000000
-			  a0000000 a0000000 10000000
-			  b0000000 b0000000 00100000
-			  c0000000 c0000000 20000000
-			  b0100000 b0100000 00100000
-			  e1000000 e1000000 00010000
-			  e1010000 e1010000 00010000
-			  e1020000 e1020000 00010000>;
+		ranges = <00000000 e0000000 00100000>;
 		reg = <e0000000 00001000>;	// CCSRBAR 1M
 		bus-frequency = <0>;		// Filled out by uboot.
 
@@ -149,115 +138,173 @@
 			interrupt-parent = <&mpic>;
 		};
 
-		pci@8000 {
-			compatible = "fsl,mpc8540-pci";
-			device_type = "pci";
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-				/* IDSEL 0x11 J17 Slot 1 */
-				8800 0 0 1 &mpic 2 1
-				8800 0 0 2 &mpic 3 1
-				8800 0 0 3 &mpic 4 1
-				8800 0 0 4 &mpic 1 1
+		global-utilities@e0000 {	//global utilities block
+			compatible = "fsl,mpc8548-guts";
+			reg = <e0000 1000>;
+			fsl,has-rstcr;
+		};
 
-				/* IDSEL 0x12 J16 Slot 2 */
+		mpic: pic@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+			big-endian;
+		};
+	};
 
-				9000 0 0 1 &mpic 3 1
-				9000 0 0 2 &mpic 4 1
-				9000 0 0 3 &mpic 2 1
-				9000 0 0 4 &mpic 1 1>;
+	pci@e0008000 {
+		compatible = "fsl,mpc8540-pci";
+		device_type = "pci";
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+			/* IDSEL 0x11 J17 Slot 1 */
+			8800 0 0 1 &mpic 2 1
+			8800 0 0 2 &mpic 3 1
+			8800 0 0 3 &mpic 4 1
+			8800 0 0 4 &mpic 1 1
+
+			/* IDSEL 0x12 J16 Slot 2 */
+
+			9000 0 0 1 &mpic 3 1
+			9000 0 0 2 &mpic 4 1
+			9000 0 0 3 &mpic 2 1
+			9000 0 0 4 &mpic 1 1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 c0000000 c0000000 0 20000000
+			  01000000 0 00000000 e1000000 0 00010000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008000 1000>;
+	};
 
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 c0000000 c0000000 0 20000000
-				  01000000 0 00000000 e1000000 0 00010000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
+	pcie@e0009000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0009000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 e1010000 0 00010000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <1a 2>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 4 1
+			0000 0 0 2 &mpic 5 1
+			0000 0 0 3 &mpic 6 1
+			0000 0 0 4 &mpic 7 1
+			>;
+		pcie@0 {
+			reg = <0 0 0 0 0>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <8000 1000>;
-		};
-
-		pcie@9000 {
-			compatible = "fsl,mpc8548-pcie";
 			device_type = "pci";
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <9000 1000>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 80000000 80000000 0 20000000
-				  01000000 0 00000000 e1010000 0 00010000>;
-			clock-frequency = <1fca055>;
-			interrupt-parent = <&mpic>;
-			interrupts = <1a 2>;
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-				/* IDSEL 0x0 */
-				0000 0 0 1 &mpic 4 1
-				0000 0 0 2 &mpic 5 1
-				0000 0 0 3 &mpic 6 1
-				0000 0 0 4 &mpic 7 1
-				>;
+			ranges = <02000000 0 80000000
+				  02000000 0 80000000
+				  0 20000000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00010000>;
 		};
+	};
 
-		pcie@a000 {
-			compatible = "fsl,mpc8548-pcie";
-			device_type = "pci";
-			#interrupt-cells = <1>;
+	pcie@e000a000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e000a000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 a0000000 a0000000 0 10000000
+			  01000000 0 00000000 e1020000 0 00010000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <19 2>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 0 1
+			0000 0 0 2 &mpic 1 1
+			0000 0 0 3 &mpic 2 1
+			0000 0 0 4 &mpic 3 1
+			>;
+		pcie@0 {
+			reg = <0 0 0 0 0>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <a000 1000>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 a0000000 a0000000 0 10000000
-				  01000000 0 00000000 e1020000 0 00010000>;
-			clock-frequency = <1fca055>;
-			interrupt-parent = <&mpic>;
-			interrupts = <19 2>;
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-				/* IDSEL 0x0 */
-				0000 0 0 1 &mpic 0 1
-				0000 0 0 2 &mpic 1 1
-				0000 0 0 3 &mpic 2 1
-				0000 0 0 4 &mpic 3 1
-				>;
+			device_type = "pci";
+			ranges = <02000000 0 a0000000
+				  02000000 0 a0000000
+				  0 10000000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00010000>;
 		};
+	};
 
-		pcie@b000 {
-			compatible = "fsl,mpc8548-pcie";
-			device_type = "pci";
-			#interrupt-cells = <1>;
+	pcie@e000b000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e000b000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 b0000000 b0000000 0 00100000
+			  01000000 0 00000000 b0100000 0 00100000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <1b 2>;
+		interrupt-map-mask = <fb00 0 0 0>;
+		interrupt-map = <
+			// IDSEL 0x1c  USB
+			e000 0 0 0 &i8259 c 2
+			e100 0 0 0 &i8259 9 2
+			e200 0 0 0 &i8259 a 2
+			e300 0 0 0 &i8259 b 2
+
+			// IDSEL 0x1d  Audio
+			e800 0 0 0 &i8259 6 2
+
+			// IDSEL 0x1e Legacy
+			f000 0 0 0 &i8259 7 2
+			f100 0 0 0 &i8259 7 2
+
+			// IDSEL 0x1f IDE/SATA
+			f800 0 0 0 &i8259 e 2
+			f900 0 0 0 &i8259 5 2
+		>;
+
+		pcie@0 {
+			reg = <0 0 0 0 0>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <b000 1000>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 b0000000 b0000000 0 00100000
-				  01000000 0 00000000 b0100000 0 00100000>;
-			clock-frequency = <1fca055>;
-			interrupt-parent = <&mpic>;
-			interrupts = <1b 2>;
-			interrupt-map-mask = <fb00 0 0 0>;
-			interrupt-map = <
-				// IDSEL 0x1c  USB
-				e000 0 0 0 &i8259 c 2
-				e100 0 0 0 &i8259 9 2
-				e200 0 0 0 &i8259 a 2
-				e300 0 0 0 &i8259 b 2
-
-				// IDSEL 0x1d  Audio
-				e800 0 0 0 &i8259 6 2
-
-				// IDSEL 0x1e Legacy
-				f000 0 0 0 &i8259 7 2
-				f100 0 0 0 &i8259 7 2
-
-				// IDSEL 0x1f IDE/SATA
-				f800 0 0 0 &i8259 e 2
-				f900 0 0 0 &i8259 5 2
-			>;
+			device_type = "pci";
+			ranges = <02000000 0 b0000000
+				  02000000 0 b0000000
+				  0 00100000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00100000>;
+
 			uli1575@0 {
 				reg = <0 0 0 0 0>;
 				#size-cells = <2>;
@@ -265,95 +312,63 @@
 				ranges = <02000000 0 b0000000
 					  02000000 0 b0000000
 					  0 00100000
+
 					  01000000 0 00000000
 					  01000000 0 00000000
 					  0 00100000>;
-
-				pci_bridge@0 {
-					reg = <0 0 0 0 0>;
-					#size-cells = <2>;
-					#address-cells = <3>;
-					ranges = <02000000 0 b0000000
-						  02000000 0 b0000000
-						  0 00100000
-						  01000000 0 00000000
-						  01000000 0 00000000
-						  0 00100000>; 
-
-					isa@1e {
-						device_type = "isa";
+				isa@1e {
+					device_type = "isa";
+					#interrupt-cells = <2>;
+					#size-cells = <1>;
+					#address-cells = <2>;
+					reg = <f000 0 0 0 0>;
+					ranges = <1 0
+						  01000000 0 0
+						  00001000>;
+					interrupt-parent = <&i8259>;
+
+					i8259: interrupt-controller@20 {
+						reg = <1 20 2
+						       1 a0 2
+						       1 4d0 2>;
+						interrupt-controller;
+						device_type = "interrupt-controller";
+						#address-cells = <0>;
 						#interrupt-cells = <2>;
-						#size-cells = <1>;
-						#address-cells = <2>;
-						reg = <f000 0 0 0 0>;
-						ranges = <1 0
-							  01000000 0 0
-							  00001000>;
+						compatible = "chrp,iic";
+						interrupts = <9 2>;
+						interrupt-parent = <&mpic>;
+					};
+
+					i8042@60 {
+						#size-cells = <0>;
+						#address-cells = <1>;
+						reg = <1 60 1 1 64 1>;
+						interrupts = <1 3 c 3>;
 						interrupt-parent = <&i8259>;
 
-						i8259: interrupt-controller@20 {
-							reg = <1 20 2
-							       1 a0 2
-							       1 4d0 2>;
-							clock-frequency = <0>;
-							interrupt-controller;
-							device_type = "interrupt-controller";
-							#address-cells = <0>;
-							#interrupt-cells = <2>;
-							built-in;
-							compatible = "chrp,iic";
-							interrupts = <9 2>;
-							interrupt-parent = <&mpic>;
+						keyboard@0 {
+							reg = <0>;
+							compatible = "pnpPNP,303";
 						};
 
-						i8042@60 {
-							#size-cells = <0>;
-							#address-cells = <1>;
-							reg = <1 60 1 1 64 1>;
-							interrupts = <1 3 c 3>;
-							interrupt-parent = <&i8259>;
-
-							keyboard@0 {
-								reg = <0>;
-								compatible = "pnpPNP,303";
-							};
-
-							mouse@1 {
-								reg = <1>;
-								compatible = "pnpPNP,f03";
-							};
+						mouse@1 {
+							reg = <1>;
+							compatible = "pnpPNP,f03";
 						};
+					};
 
-						rtc@70 {
-							compatible = "pnpPNP,b00";
-							reg = <1 70 2>;
-						};
+					rtc@70 {
+						compatible = "pnpPNP,b00";
+						reg = <1 70 2>;
+					};
 
-						gpio@400 {
-							reg = <1 400 80>;
-						};
+					gpio@400 {
+						reg = <1 400 80>;
 					};
 				};
 			};
-
 		};
 
-		global-utilities@e0000 {	//global utilities block
-			compatible = "fsl,mpc8548-guts";
-			reg = <e0000 1000>;
-			fsl,has-rstcr;
-		};
-
-		mpic: pic@40000 {
-			clock-frequency = <0>;
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <2>;
-			reg = <40000 40000>;
-			built-in;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
-			big-endian;
-		};
 	};
 };

arch/powerpc/boot/dts/mpc8548cds.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <0>;	//  33 MHz, from uboot
 			bus-frequency = <0>;	// 166 MHz
 			clock-frequency = <0>;	// 825 MHz, from uboot
-			32-bit;
 		};
 	};
 
@@ -42,15 +41,8 @@
 	soc8548@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
-		ranges = <00001000 e0001000 000ff000
-			  80000000 80000000 10000000
-			  e2000000 e2000000 00800000
-			  90000000 90000000 10000000
-			  e2800000 e2800000 00800000
-			  a0000000 a0000000 20000000
-		          e3000000 e3000000 01000000>;
+		ranges = <00000000 e0000000 00100000>;
 		reg = <e0000000 00001000>;	// CCSRBAR
 		bus-frequency = <0>;
 
@@ -189,215 +181,225 @@
 			fsl,has-rstcr;
 		};
 
-		pci@8000 {
+		mpic: pic@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+                        big-endian;
+		};
+	};
+
+	pci@e0008000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x4 (PCIX Slot 2) */
+			02000 0 0 1 &mpic 0 1
+			02000 0 0 2 &mpic 1 1
+			02000 0 0 3 &mpic 2 1
+			02000 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x5 (PCIX Slot 3) */
+			02800 0 0 1 &mpic 1 1
+			02800 0 0 2 &mpic 2 1
+			02800 0 0 3 &mpic 3 1
+			02800 0 0 4 &mpic 0 1
+
+			/* IDSEL 0x6 (PCIX Slot 4) */
+			03000 0 0 1 &mpic 2 1
+			03000 0 0 2 &mpic 3 1
+			03000 0 0 3 &mpic 0 1
+			03000 0 0 4 &mpic 1 1
+
+			/* IDSEL 0x8 (PCIX Slot 5) */
+			04000 0 0 1 &mpic 0 1
+			04000 0 0 2 &mpic 1 1
+			04000 0 0 3 &mpic 2 1
+			04000 0 0 4 &mpic 3 1
+
+			/* IDSEL 0xC (Tsi310 bridge) */
+			06000 0 0 1 &mpic 0 1
+			06000 0 0 2 &mpic 1 1
+			06000 0 0 3 &mpic 2 1
+			06000 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x14 (Slot 2) */
+			0a000 0 0 1 &mpic 0 1
+			0a000 0 0 2 &mpic 1 1
+			0a000 0 0 3 &mpic 2 1
+			0a000 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x15 (Slot 3) */
+			0a800 0 0 1 &mpic 1 1
+			0a800 0 0 2 &mpic 2 1
+			0a800 0 0 3 &mpic 3 1
+			0a800 0 0 4 &mpic 0 1
+
+			/* IDSEL 0x16 (Slot 4) */
+			0b000 0 0 1 &mpic 2 1
+			0b000 0 0 2 &mpic 3 1
+			0b000 0 0 3 &mpic 0 1
+			0b000 0 0 4 &mpic 1 1
+
+			/* IDSEL 0x18 (Slot 5) */
+			0c000 0 0 1 &mpic 0 1
+			0c000 0 0 2 &mpic 1 1
+			0c000 0 0 3 &mpic 2 1
+			0c000 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x1C (Tsi310 bridge PCI primary) */
+			0E000 0 0 1 &mpic 0 1
+			0E000 0 0 2 &mpic 1 1
+			0E000 0 0 3 &mpic 2 1
+			0E000 0 0 4 &mpic 3 1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 80000000 80000000 0 10000000
+			  01000000 0 00000000 e2000000 0 00800000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008000 1000>;
+		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+		device_type = "pci";
+
+		pci_bridge@1c {
 			interrupt-map-mask = <f800 0 0 7>;
 			interrupt-map = <
-				/* IDSEL 0x4 (PCIX Slot 2) */
-				02000 0 0 1 &mpic 0 1
-				02000 0 0 2 &mpic 1 1
-				02000 0 0 3 &mpic 2 1
-				02000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x5 (PCIX Slot 3) */
-				02800 0 0 1 &mpic 1 1
-				02800 0 0 2 &mpic 2 1
-				02800 0 0 3 &mpic 3 1
-				02800 0 0 4 &mpic 0 1
-
-				/* IDSEL 0x6 (PCIX Slot 4) */
-				03000 0 0 1 &mpic 2 1
-				03000 0 0 2 &mpic 3 1
-				03000 0 0 3 &mpic 0 1
-				03000 0 0 4 &mpic 1 1
-
-				/* IDSEL 0x8 (PCIX Slot 5) */
-				04000 0 0 1 &mpic 0 1
-				04000 0 0 2 &mpic 1 1
-				04000 0 0 3 &mpic 2 1
-				04000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0xC (Tsi310 bridge) */
-				06000 0 0 1 &mpic 0 1
-				06000 0 0 2 &mpic 1 1
-				06000 0 0 3 &mpic 2 1
-				06000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x14 (Slot 2) */
-				0a000 0 0 1 &mpic 0 1
-				0a000 0 0 2 &mpic 1 1
-				0a000 0 0 3 &mpic 2 1
-				0a000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x15 (Slot 3) */
-				0a800 0 0 1 &mpic 1 1
-				0a800 0 0 2 &mpic 2 1
-				0a800 0 0 3 &mpic 3 1
-				0a800 0 0 4 &mpic 0 1
-
-				/* IDSEL 0x16 (Slot 4) */
-				0b000 0 0 1 &mpic 2 1
-				0b000 0 0 2 &mpic 3 1
-				0b000 0 0 3 &mpic 0 1
-				0b000 0 0 4 &mpic 1 1
-
-				/* IDSEL 0x18 (Slot 5) */
-				0c000 0 0 1 &mpic 0 1
-				0c000 0 0 2 &mpic 1 1
-				0c000 0 0 3 &mpic 2 1
-				0c000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x1C (Tsi310 bridge PCI primary) */
-				0E000 0 0 1 &mpic 0 1
-				0E000 0 0 2 &mpic 1 1
-				0E000 0 0 3 &mpic 2 1
-				0E000 0 0 4 &mpic 3 1>;
 
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 80000000 80000000 0 10000000
-				  01000000 0 00000000 e2000000 0 00800000>;
-			clock-frequency = <3f940aa>;
+				/* IDSEL 0x00 (PrPMC Site) */
+				0000 0 0 1 &mpic 0 1
+				0000 0 0 2 &mpic 1 1
+				0000 0 0 3 &mpic 2 1
+				0000 0 0 4 &mpic 3 1
+
+				/* IDSEL 0x04 (VIA chip) */
+				2000 0 0 1 &mpic 0 1
+				2000 0 0 2 &mpic 1 1
+				2000 0 0 3 &mpic 2 1
+				2000 0 0 4 &mpic 3 1
+
+				/* IDSEL 0x05 (8139) */
+				2800 0 0 1 &mpic 1 1
+
+				/* IDSEL 0x06 (Slot 6) */
+				3000 0 0 1 &mpic 2 1
+				3000 0 0 2 &mpic 3 1
+				3000 0 0 3 &mpic 0 1
+				3000 0 0 4 &mpic 1 1
+
+				/* IDESL 0x07 (Slot 7) */
+				3800 0 0 1 &mpic 3 1
+				3800 0 0 2 &mpic 0 1
+				3800 0 0 3 &mpic 1 1
+				3800 0 0 4 &mpic 2 1>;
+
+			reg = <e000 0 0 0 0>;
 			#interrupt-cells = <1>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <8000 1000>;
-			compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
-			device_type = "pci";
+			ranges = <02000000 0 80000000
+				  02000000 0 80000000
+				  0 20000000
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00080000>;
+			clock-frequency = <1fca055>;
 
-			pci_bridge@1c {
-				interrupt-map-mask = <f800 0 0 7>;
-				interrupt-map = <
-
-					/* IDSEL 0x00 (PrPMC Site) */
-					0000 0 0 1 &mpic 0 1
-					0000 0 0 2 &mpic 1 1
-					0000 0 0 3 &mpic 2 1
-					0000 0 0 4 &mpic 3 1
-
-					/* IDSEL 0x04 (VIA chip) */
-					2000 0 0 1 &mpic 0 1
-					2000 0 0 2 &mpic 1 1
-					2000 0 0 3 &mpic 2 1
-					2000 0 0 4 &mpic 3 1
-
-					/* IDSEL 0x05 (8139) */
-					2800 0 0 1 &mpic 1 1
-
-					/* IDSEL 0x06 (Slot 6) */
-					3000 0 0 1 &mpic 2 1
-					3000 0 0 2 &mpic 3 1
-					3000 0 0 3 &mpic 0 1
-					3000 0 0 4 &mpic 1 1
-
-					/* IDESL 0x07 (Slot 7) */
-					3800 0 0 1 &mpic 3 1
-					3800 0 0 2 &mpic 0 1
-					3800 0 0 3 &mpic 1 1
-					3800 0 0 4 &mpic 2 1>;
-
-				reg = <e000 0 0 0 0>;
-				#interrupt-cells = <1>;
-				#size-cells = <2>;
-				#address-cells = <3>;
-				ranges = <02000000 0 80000000
-					  02000000 0 80000000
-					  0 20000000
-					  01000000 0 00000000
-					  01000000 0 00000000
-					  0 00080000>;
-				clock-frequency = <1fca055>;
-
-				isa@4 {
-					device_type = "isa";
+			isa@4 {
+				device_type = "isa";
+				#interrupt-cells = <2>;
+				#size-cells = <1>;
+				#address-cells = <2>;
+				reg = <2000 0 0 0 0>;
+				ranges = <1 0 01000000 0 0 00001000>;
+				interrupt-parent = <&i8259>;
+
+				i8259: interrupt-controller@20 {
+					interrupt-controller;
+					device_type = "interrupt-controller";
+					reg = <1 20 2
+					       1 a0 2
+					       1 4d0 2>;
+					#address-cells = <0>;
 					#interrupt-cells = <2>;
-					#size-cells = <1>;
-					#address-cells = <2>;
-					reg = <2000 0 0 0 0>;
-					ranges = <1 0 01000000 0 0 00001000>;
-					interrupt-parent = <&i8259>;
-
-					i8259: interrupt-controller@20 {
-						clock-frequency = <0>;
-						interrupt-controller;
-						device_type = "interrupt-controller";
-						reg = <1 20 2
-						       1 a0 2
-						       1 4d0 2>;
-						#address-cells = <0>;
-						#interrupt-cells = <2>;
-						built-in;
-						compatible = "chrp,iic";
-						interrupts = <0 1>;
-						interrupt-parent = <&mpic>;
-					};
-
-					rtc@70 {
-						compatible = "pnpPNP,b00";
-						reg = <1 70 2>;
-					};
+					compatible = "chrp,iic";
+					interrupts = <0 1>;
+					interrupt-parent = <&mpic>;
 				};
-			};
-		};
 
-		pci@9000 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-				/* IDSEL 0x15 */
-				a800 0 0 1 &mpic b 1
-				a800 0 0 2 &mpic 1 1
-				a800 0 0 3 &mpic 2 1
-				a800 0 0 4 &mpic 3 1>;
-
-			interrupt-parent = <&mpic>;
-			interrupts = <19 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 90000000 90000000 0 10000000
-				  01000000 0 00000000 e2800000 0 00800000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <9000 1000>;
-			compatible = "fsl,mpc8540-pci";
-			device_type = "pci";
+				rtc@70 {
+					compatible = "pnpPNP,b00";
+					reg = <1 70 2>;
+				};
+			};
 		};
-		/* PCI Express */
-		pcie@a000 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
+	};
 
-				/* IDSEL 0x0 (PEX) */
-				00000 0 0 1 &mpic 0 1
-				00000 0 0 2 &mpic 1 1
-				00000 0 0 3 &mpic 2 1
-				00000 0 0 4 &mpic 3 1>;
+	pci@e0009000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+			/* IDSEL 0x15 */
+			a800 0 0 1 &mpic b 1
+			a800 0 0 2 &mpic 1 1
+			a800 0 0 3 &mpic 2 1
+			a800 0 0 4 &mpic 3 1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <19 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 90000000 90000000 0 10000000
+			  01000000 0 00000000 e2800000 0 00800000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0009000 1000>;
+		compatible = "fsl,mpc8540-pci";
+		device_type = "pci";
+	};
 
-			interrupt-parent = <&mpic>;
-			interrupts = <1a 2>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 a0000000 a0000000 0 20000000
-				  01000000 0 00000000 e3000000 0 08000000>;
-			clock-frequency = <1fca055>;
-			#interrupt-cells = <1>;
+	pcie@e000a000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+			/* IDSEL 0x0 (PEX) */
+			00000 0 0 1 &mpic 0 1
+			00000 0 0 2 &mpic 1 1
+			00000 0 0 3 &mpic 2 1
+			00000 0 0 4 &mpic 3 1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <1a 2>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 a0000000 a0000000 0 20000000
+			  01000000 0 00000000 e3000000 0 08000000>;
+		clock-frequency = <1fca055>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e000a000 1000>;
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		pcie@0 {
+			reg = <0 0 0 0 0>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <a000 1000>;
-			compatible = "fsl,mpc8548-pcie";
 			device_type = "pci";
-		};
+			ranges = <02000000 0 a0000000
+				  02000000 0 a0000000
+				  0 20000000
 
-		mpic: pic@40000 {
-			clock-frequency = <0>;
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <2>;
-			reg = <40000 40000>;
-			built-in;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
-                        big-endian;
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 08000000>;
 		};
 	};
 };

arch/powerpc/boot/dts/mpc8555cds.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <0>;	//  33 MHz, from uboot
 			bus-frequency = <0>;	// 166 MHz
 			clock-frequency = <0>;	// 825 MHz, from uboot
-			32-bit;
 		};
 	};
 
@@ -42,10 +41,9 @@
 	soc8555@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
-		reg = <e0000000 00100000>;	// CCSRBAR 1M
+		reg = <e0000000 00001000>;	// CCSRBAR 1M
 		bus-frequency = <0>;
 
 		memory-controller@2000 {
@@ -137,113 +135,145 @@
 			interrupt-parent = <&mpic>;
 		};
 
-		pci1: pci@8000 {
-			interrupt-map-mask = <1f800 0 0 7>;
-			interrupt-map = <
-
-				/* IDSEL 0x10 */
-				08000 0 0 1 &mpic 0 1
-				08000 0 0 2 &mpic 1 1
-				08000 0 0 3 &mpic 2 1
-				08000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x11 */
-				08800 0 0 1 &mpic 0 1
-				08800 0 0 2 &mpic 1 1
-				08800 0 0 3 &mpic 2 1
-				08800 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x12 (Slot 1) */
-				09000 0 0 1 &mpic 0 1
-				09000 0 0 2 &mpic 1 1
-				09000 0 0 3 &mpic 2 1
-				09000 0 0 4 &mpic 3 1
-
-				/* IDSEL 0x13 (Slot 2) */
-				09800 0 0 1 &mpic 1 1
-				09800 0 0 2 &mpic 2 1
-				09800 0 0 3 &mpic 3 1
-				09800 0 0 4 &mpic 0 1
-
-				/* IDSEL 0x14 (Slot 3) */
-				0a000 0 0 1 &mpic 2 1
-				0a000 0 0 2 &mpic 3 1
-				0a000 0 0 3 &mpic 0 1
-				0a000 0 0 4 &mpic 1 1
-
-				/* IDSEL 0x15 (Slot 4) */
-				0a800 0 0 1 &mpic 3 1
-				0a800 0 0 2 &mpic 0 1
-				0a800 0 0 3 &mpic 1 1
-				0a800 0 0 4 &mpic 2 1
-
-				/* Bus 1 (Tundra Bridge) */
-				/* IDSEL 0x12 (ISA bridge) */
-				19000 0 0 1 &mpic 0 1
-				19000 0 0 2 &mpic 1 1
-				19000 0 0 3 &mpic 2 1
-				19000 0 0 4 &mpic 3 1>;
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 80000000 80000000 0 20000000
-				  01000000 0 00000000 e2000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8000 1000>;
-			compatible = "fsl,mpc8540-pci";
-			device_type = "pci";
-
-			i8259@19000 {
-				clock-frequency = <0>;
+		mpic: pic@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+                        big-endian;
+		};
+
+		cpm@919c0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,mpc8555-cpm", "fsl,cpm2";
+			reg = <919c0 30>;
+			ranges;
+
+			muram@80000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 80000 10000>;
+
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0 2000 9000 1000>;
+				};
+			};
+
+			brg@919f0 {
+				compatible = "fsl,mpc8555-brg",
+				             "fsl,cpm2-brg",
+				             "fsl,cpm-brg";
+				reg = <919f0 10 915f0 10>;
+			};
+
+			cpmpic: pic@90c00 {
 				interrupt-controller;
-				device_type = "interrupt-controller";
-				reg = <19000 0 0 0 1>;
 				#address-cells = <0>;
 				#interrupt-cells = <2>;
-				built-in;
-				compatible = "chrp,iic";
-				big-endian;
-				interrupts = <1>;
-				interrupt-parent = <&pci1>;
+				interrupts = <2e 2>;
+				interrupt-parent = <&mpic>;
+				reg = <90c00 80>;
+				compatible = "fsl,mpc8555-cpm-pic", "fsl,cpm2-pic";
 			};
 		};
+	};
 
-		pci@9000 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
+	pci1: pci@e0008000 {
+		interrupt-map-mask = <1f800 0 0 7>;
+		interrupt-map = <
 
-				/* IDSEL 0x15 */
-				a800 0 0 1 &mpic b 1
-				a800 0 0 2 &mpic b 1
-				a800 0 0 3 &mpic b 1
-				a800 0 0 4 &mpic b 1>;
-			interrupt-parent = <&mpic>;
-			interrupts = <19 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 a0000000 a0000000 0 20000000
-				  01000000 0 00000000 e3000000 0 00100000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <9000 1000>;
-			compatible = "fsl,mpc8540-pci";
-			device_type = "pci";
-		};
+			/* IDSEL 0x10 */
+			08000 0 0 1 &mpic 0 1
+			08000 0 0 2 &mpic 1 1
+			08000 0 0 3 &mpic 2 1
+			08000 0 0 4 &mpic 3 1
 
-		mpic: pic@40000 {
-			clock-frequency = <0>;
+			/* IDSEL 0x11 */
+			08800 0 0 1 &mpic 0 1
+			08800 0 0 2 &mpic 1 1
+			08800 0 0 3 &mpic 2 1
+			08800 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x12 (Slot 1) */
+			09000 0 0 1 &mpic 0 1
+			09000 0 0 2 &mpic 1 1
+			09000 0 0 3 &mpic 2 1
+			09000 0 0 4 &mpic 3 1
+
+			/* IDSEL 0x13 (Slot 2) */
+			09800 0 0 1 &mpic 1 1
+			09800 0 0 2 &mpic 2 1
+			09800 0 0 3 &mpic 3 1
+			09800 0 0 4 &mpic 0 1
+
+			/* IDSEL 0x14 (Slot 3) */
+			0a000 0 0 1 &mpic 2 1
+			0a000 0 0 2 &mpic 3 1
+			0a000 0 0 3 &mpic 0 1
+			0a000 0 0 4 &mpic 1 1
+
+			/* IDSEL 0x15 (Slot 4) */
+			0a800 0 0 1 &mpic 3 1
+			0a800 0 0 2 &mpic 0 1
+			0a800 0 0 3 &mpic 1 1
+			0a800 0 0 4 &mpic 2 1
+
+			/* Bus 1 (Tundra Bridge) */
+			/* IDSEL 0x12 (ISA bridge) */
+			19000 0 0 1 &mpic 0 1
+			19000 0 0 2 &mpic 1 1
+			19000 0 0 3 &mpic 2 1
+			19000 0 0 4 &mpic 3 1>;
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 e2000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008000 1000>;
+		compatible = "fsl,mpc8540-pci";
+		device_type = "pci";
+
+		i8259@19000 {
 			interrupt-controller;
+			device_type = "interrupt-controller";
+			reg = <19000 0 0 0 1>;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
-			reg = <40000 40000>;
-			built-in;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
-                        big-endian;
+			compatible = "chrp,iic";
+			interrupts = <1>;
+			interrupt-parent = <&pci1>;
 		};
 	};
+
+	pci@e0009000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+			/* IDSEL 0x15 */
+			a800 0 0 1 &mpic b 1
+			a800 0 0 2 &mpic b 1
+			a800 0 0 3 &mpic b 1
+			a800 0 0 4 &mpic b 1>;
+		interrupt-parent = <&mpic>;
+		interrupts = <19 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 a0000000 a0000000 0 20000000
+			  01000000 0 00000000 e3000000 0 00100000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0009000 1000>;
+		compatible = "fsl,mpc8540-pci";
+		device_type = "pci";
+	};
 };

arch/powerpc/boot/dts/mpc8560ads.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <04ead9a0>;
 			bus-frequency = <13ab6680>;
 			clock-frequency = <312c8040>;
-			32-bit;
 		};
 	};
 
@@ -42,7 +41,6 @@
 	soc8560@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
 		reg = <e0000000 00000200>;
@@ -132,115 +130,39 @@
 			phy-handle = <&phy1>;
 		};
 
-		pci@8000 {
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
-			device_type = "pci";
-			reg = <8000 1000>;
-			clock-frequency = <3f940aa>;
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-					/* IDSEL 0x2 */
-					 1000 0 0 1 &mpic 1 1
-					 1000 0 0 2 &mpic 2 1
-					 1000 0 0 3 &mpic 3 1
-					 1000 0 0 4 &mpic 4 1
-
-					/* IDSEL 0x3 */
-					 1800 0 0 1 &mpic 4 1
-					 1800 0 0 2 &mpic 1 1
-					 1800 0 0 3 &mpic 2 1
-					 1800 0 0 4 &mpic 3 1
-
-					/* IDSEL 0x4 */
-					 2000 0 0 1 &mpic 3 1
-					 2000 0 0 2 &mpic 4 1
-					 2000 0 0 3 &mpic 1 1
-					 2000 0 0 4 &mpic 2 1
-
-					/* IDSEL 0x5  */
-					 2800 0 0 1 &mpic 2 1
-					 2800 0 0 2 &mpic 3 1
-					 2800 0 0 3 &mpic 4 1
-					 2800 0 0 4 &mpic 1 1
-
-					/* IDSEL 12 */
-					 6000 0 0 1 &mpic 1 1
-					 6000 0 0 2 &mpic 2 1
-					 6000 0 0 3 &mpic 3 1
-					 6000 0 0 4 &mpic 4 1
-
-					/* IDSEL 13 */
-					 6800 0 0 1 &mpic 4 1
-					 6800 0 0 2 &mpic 1 1
-					 6800 0 0 3 &mpic 2 1
-					 6800 0 0 4 &mpic 3 1
-
-					/* IDSEL 14*/
-					 7000 0 0 1 &mpic 3 1
-					 7000 0 0 2 &mpic 4 1
-					 7000 0 0 3 &mpic 1 1
-					 7000 0 0 4 &mpic 2 1
-
-					/* IDSEL 15 */
-					 7800 0 0 1 &mpic 2 1
-					 7800 0 0 2 &mpic 3 1
-					 7800 0 0 3 &mpic 4 1
-					 7800 0 0 4 &mpic 1 1
-
-					/* IDSEL 18 */
-					 9000 0 0 1 &mpic 1 1
-					 9000 0 0 2 &mpic 2 1
-					 9000 0 0 3 &mpic 3 1
-					 9000 0 0 4 &mpic 4 1
-
-					/* IDSEL 19 */
-					 9800 0 0 1 &mpic 4 1
-					 9800 0 0 2 &mpic 1 1
-					 9800 0 0 3 &mpic 2 1
-					 9800 0 0 4 &mpic 3 1
-
-					/* IDSEL 20 */
-					 a000 0 0 1 &mpic 3 1
-					 a000 0 0 2 &mpic 4 1
-					 a000 0 0 3 &mpic 1 1
-					 a000 0 0 4 &mpic 2 1
-
-					/* IDSEL 21 */
-					 a800 0 0 1 &mpic 2 1
-					 a800 0 0 2 &mpic 3 1
-					 a800 0 0 3 &mpic 4 1
-					 a800 0 0 4 &mpic 1 1>;
-
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			bus-range = <0 0>;
-			ranges = <02000000 0 80000000 80000000 0 20000000
-				  01000000 0 00000000 e2000000 0 01000000>;
-		};
-
 		mpic: pic@40000 {
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <40000 40000>;
-			built-in;
 			device_type = "open-pic";
 		};
 
-		cpm@e0000000 {
+		cpm@919c0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-			#interrupt-cells = <2>;
-			device_type = "cpm";
-			model = "CPM2";
-			ranges = <0 0 c0000>;
-			reg = <80000 40000>;
-			command-proc = <919c0>;
-			brg-frequency = <9d5b340>;
+			compatible = "fsl,mpc8560-cpm", "fsl,cpm2";
+			reg = <919c0 30>;
+			ranges;
+
+			muram@80000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 80000 10000>;
+
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0 4000 9000 2000>;
+				};
+			};
+
+			brg@919f0 {
+				compatible = "fsl,mpc8560-brg",
+				             "fsl,cpm2-brg",
+				             "fsl,cpm-brg";
+				reg = <919f0 10 915f0 10>;
+				clock-frequency = <d#165000000>;
+			};
 
 			cpmpic: pic@90c00 {
 				interrupt-controller;
@@ -249,44 +171,38 @@
 				interrupts = <2e 2>;
 				interrupt-parent = <&mpic>;
 				reg = <90c00 80>;
-				built-in;
-				device_type = "cpm-pic";
+				compatible = "fsl,mpc8560-cpm-pic", "fsl,cpm2-pic";
 			};
 
-			scc@91a00 {
+			serial@91a00 {
 				device_type = "serial";
-				compatible = "cpm_uart";
-				model = "SCC";
-				device-id = <1>;
+				compatible = "fsl,mpc8560-scc-uart",
+				             "fsl,cpm2-scc-uart";
 				reg = <91a00 20 88000 100>;
-				clock-setup = <00ffffff 0>;
-				rx-clock = <1>;
-				tx-clock = <1>;
+				fsl,cpm-brg = <1>;
+				fsl,cpm-command = <00800000>;
 				current-speed = <1c200>;
 				interrupts = <28 8>;
 				interrupt-parent = <&cpmpic>;
 			};
 
-			scc@91a20 {
+			serial@91a20 {
 				device_type = "serial";
-				compatible = "cpm_uart";
-				model = "SCC";
-				device-id = <2>;
+				compatible = "fsl,mpc8560-scc-uart",
+				             "fsl,cpm2-scc-uart";
 				reg = <91a20 20 88100 100>;
-				clock-setup = <ff00ffff 90000>;
-				rx-clock = <2>;
-				tx-clock = <2>;
+				fsl,cpm-brg = <2>;
+				fsl,cpm-command = <04a00000>;
 				current-speed = <1c200>;
 				interrupts = <29 8>;
 				interrupt-parent = <&cpmpic>;
 			};
 
-			fcc@91320 {
+			ethernet@91320 {
 				device_type = "network";
-				compatible = "fs_enet";
-				model = "FCC";
-				device-id = <2>;
-				reg = <91320 20 88500 100 913a0 30>;
+				compatible = "fsl,mpc8560-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <91320 20 88500 100 913b0 1>;
 				/*
 				 * mac-address is deprecated and will be removed
 				 * in 2.6.25.  Only recent versions of
@@ -294,20 +210,17 @@
 				 */
 				mac-address = [ 00 00 00 00 00 00 ];
 				local-mac-address = [ 00 00 00 00 00 00 ];
-				clock-setup = <ff00ffff 250000>;
-				rx-clock = <15>;
-				tx-clock = <16>;
+				fsl,cpm-command = <16200300>;
 				interrupts = <21 8>;
 				interrupt-parent = <&cpmpic>;
 				phy-handle = <&phy2>;
 			};
 
-			fcc@91340 {
+			ethernet@91340 {
 				device_type = "network";
-				compatible = "fs_enet";
-				model = "FCC";
-				device-id = <3>;
-				reg = <91340 20 88600 100 913d0 30>;
+				compatible = "fsl,mpc8560-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <91340 20 88600 100 913d0 1>;
 				/*
 				 * mac-address is deprecated and will be removed
 				 * in 2.6.25.  Only recent versions of
@@ -315,13 +228,101 @@
 				 */
 				mac-address = [ 00 00 00 00 00 00 ];
 				local-mac-address = [ 00 00 00 00 00 00 ];
-				clock-setup = <ffff00ff 3700>;
-				rx-clock = <17>;
-				tx-clock = <18>;
+				fsl,cpm-command = <1a400300>;
 				interrupts = <22 8>;
 				interrupt-parent = <&cpmpic>;
 				phy-handle = <&phy3>;
 			};
 		};
 	};
+
+	pci@e0008000 {
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+		device_type = "pci";
+		reg = <e0008000 1000>;
+		clock-frequency = <3f940aa>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+				/* IDSEL 0x2 */
+				 1000 0 0 1 &mpic 1 1
+				 1000 0 0 2 &mpic 2 1
+				 1000 0 0 3 &mpic 3 1
+				 1000 0 0 4 &mpic 4 1
+
+				/* IDSEL 0x3 */
+				 1800 0 0 1 &mpic 4 1
+				 1800 0 0 2 &mpic 1 1
+				 1800 0 0 3 &mpic 2 1
+				 1800 0 0 4 &mpic 3 1
+
+				/* IDSEL 0x4 */
+				 2000 0 0 1 &mpic 3 1
+				 2000 0 0 2 &mpic 4 1
+				 2000 0 0 3 &mpic 1 1
+				 2000 0 0 4 &mpic 2 1
+
+				/* IDSEL 0x5  */
+				 2800 0 0 1 &mpic 2 1
+				 2800 0 0 2 &mpic 3 1
+				 2800 0 0 3 &mpic 4 1
+				 2800 0 0 4 &mpic 1 1
+
+				/* IDSEL 12 */
+				 6000 0 0 1 &mpic 1 1
+				 6000 0 0 2 &mpic 2 1
+				 6000 0 0 3 &mpic 3 1
+				 6000 0 0 4 &mpic 4 1
+
+				/* IDSEL 13 */
+				 6800 0 0 1 &mpic 4 1
+				 6800 0 0 2 &mpic 1 1
+				 6800 0 0 3 &mpic 2 1
+				 6800 0 0 4 &mpic 3 1
+
+				/* IDSEL 14*/
+				 7000 0 0 1 &mpic 3 1
+				 7000 0 0 2 &mpic 4 1
+				 7000 0 0 3 &mpic 1 1
+				 7000 0 0 4 &mpic 2 1
+
+				/* IDSEL 15 */
+				 7800 0 0 1 &mpic 2 1
+				 7800 0 0 2 &mpic 3 1
+				 7800 0 0 3 &mpic 4 1
+				 7800 0 0 4 &mpic 1 1
+
+				/* IDSEL 18 */
+				 9000 0 0 1 &mpic 1 1
+				 9000 0 0 2 &mpic 2 1
+				 9000 0 0 3 &mpic 3 1
+				 9000 0 0 4 &mpic 4 1
+
+				/* IDSEL 19 */
+				 9800 0 0 1 &mpic 4 1
+				 9800 0 0 2 &mpic 1 1
+				 9800 0 0 3 &mpic 2 1
+				 9800 0 0 4 &mpic 3 1
+
+				/* IDSEL 20 */
+				 a000 0 0 1 &mpic 3 1
+				 a000 0 0 2 &mpic 4 1
+				 a000 0 0 3 &mpic 1 1
+				 a000 0 0 4 &mpic 2 1
+
+				/* IDSEL 21 */
+				 a800 0 0 1 &mpic 2 1
+				 a800 0 0 2 &mpic 3 1
+				 a800 0 0 3 &mpic 4 1
+				 a800 0 0 4 &mpic 1 1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 e2000000 0 01000000>;
+	};
 };

arch/powerpc/boot/dts/mpc8568mds.dts

@@ -34,7 +34,6 @@
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
-			32-bit;
 		};
 	};
 
@@ -51,10 +50,9 @@
 	soc8568@e0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 e0000000 00100000>;
-		reg = <e0000000 00100000>;
+		reg = <e0000000 00001000>;
 		bus-frequency = <0>;
 
 		memory-controller@2000 {
@@ -74,15 +72,24 @@
 		};
 
 		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
 			device_type = "i2c";
 			compatible = "fsl-i2c";
 			reg = <3000 100>;
 			interrupts = <2b 2>;
 			interrupt-parent = <&mpic>;
 			dfsrr;
+
+			rtc@68 {
+				compatible = "dallas,ds1374";
+				reg = <68>;
+			};
 		};
 
 		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
 			device_type = "i2c";
 			compatible = "fsl-i2c";
 			reg = <3100 100>;
@@ -97,10 +104,10 @@
 			device_type = "mdio";
 			compatible = "gianfar";
 			reg = <24520 20>;
-			phy0: ethernet-phy@0 {
+			phy0: ethernet-phy@7 {
 				interrupt-parent = <&mpic>;
 				interrupts = <1 1>;
-				reg = <0>;
+				reg = <7>;
 				device_type = "ethernet-phy";
 			};
 			phy1: ethernet-phy@1 {
@@ -176,60 +183,6 @@
 			fsl,has-rstcr;
 		};
 
-		pci@8000 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-				/* IDSEL 0x12 AD18 */
-				9000 0 0 1 &mpic 5 1
-				9000 0 0 2 &mpic 6 1
-				9000 0 0 3 &mpic 7 1
-				9000 0 0 4 &mpic 4 1
-
-				/* IDSEL 0x13 AD19 */
-				9800 0 0 1 &mpic 6 1
-				9800 0 0 2 &mpic 7 1
-				9800 0 0 3 &mpic 4 1
-				9800 0 0 4 &mpic 5 1>;
-
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 80000000 80000000 0 20000000
-				  01000000 0 00000000 e2000000 0 00800000>;
-			clock-frequency = <3f940aa>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <8000 1000>;
-			compatible = "fsl,mpc8540-pci";
-			device_type = "pci";
-		};
-
-		/* PCI Express */
-		pcie@a000 {
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-
-				/* IDSEL 0x0 (PEX) */
-				00000 0 0 1 &mpic 0 1
-				00000 0 0 2 &mpic 1 1
-				00000 0 0 3 &mpic 2 1
-				00000 0 0 4 &mpic 3 1>;
-
-			interrupt-parent = <&mpic>;
-			interrupts = <1a 2>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 a0000000 a0000000 0 20000000
-				  01000000 0 00000000 e3000000 0 08000000>;
-			clock-frequency = <1fca055>;
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			reg = <a000 1000>;
-			compatible = "fsl,mpc8548-pcie";
-			device_type = "pci";
-		};
-
 		serial@4600 {
 			device_type = "serial";
 			compatible = "ns16550";
@@ -258,11 +211,11 @@
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <40000 40000>;
-			built-in;
 			compatible = "chrp,open-pic";
 			device_type = "open-pic";
                         big-endian;
 		};
+
 		par_io@e0100 {
 			reg = <e0100 100>;
 			device_type = "par_io";
@@ -289,12 +242,13 @@
 					4  1a  2  0  2  0 	/* RxD7 */
 					4  0b  1  0  2  0 	/* TX_EN */
 					4  18  1  0  2  0 	/* TX_ER */
-					4  0f  2  0  2  0 	/* RX_DV */
+					4  10  2  0  2  0 	/* RX_DV */
 					4  1e  2  0  2  0 	/* RX_ER */
 					4  11  2  0  2  0 	/* RX_CLK */
 					4  13  1  0  2  0 	/* GTX_CLK */
 					1  1f  2  0  3  0>;	/* GTX125 */
 			};
+
 			pio2: ucc_pin@02 {
 				pio-map = <
 			/* port  pin  dir  open_drain  assignment  has_irq */
@@ -380,10 +334,10 @@
 			mac-address = [ 00 00 00 00 00 00 ];
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			rx-clock = <0>;
-			tx-clock = <19>;
-			phy-handle = <&qe_phy0>;
-			phy-connection-type = "gmii";
+			tx-clock = <20>;
 			pio-handle = <&pio1>;
+			phy-handle = <&phy0>;
+			phy-connection-type = "rgmii-id";
 		};
 
 		ucc@3000 {
@@ -402,10 +356,10 @@
 			mac-address = [ 00 00 00 00 00 00 ];
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			rx-clock = <0>;
-			tx-clock = <14>;
-			phy-handle = <&qe_phy1>;
-			phy-connection-type = "gmii";
+			tx-clock = <20>;
 			pio-handle = <&pio2>;
+			phy-handle = <&phy1>;
+			phy-connection-type = "rgmii-id";
 		};
 
 		mdio@2120 {
@@ -417,10 +371,10 @@
 
 			/* These are the same PHYs as on
 			 * gianfar's MDIO bus */
-			qe_phy0: ethernet-phy@00 {
+			qe_phy0: ethernet-phy@07 {
 				interrupt-parent = <&mpic>;
 				interrupts = <1 1>;
-				reg = <0>;
+				reg = <7>;
 				device_type = "ethernet-phy";
 			};
 			qe_phy1: ethernet-phy@01 {
@@ -449,11 +403,77 @@
 			#address-cells = <0>;
 			#interrupt-cells = <1>;
 			reg = <80 80>;
-			built-in;
 			big-endian;
 			interrupts = <2e 2 2e 2>; //high:30 low:30
 			interrupt-parent = <&mpic>;
 		};
 
 	};
+
+	pci@e0008000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x12 AD18 */
+			9000 0 0 1 &mpic 5 1
+			9000 0 0 2 &mpic 6 1
+			9000 0 0 3 &mpic 7 1
+			9000 0 0 4 &mpic 4 1
+
+			/* IDSEL 0x13 AD19 */
+			9800 0 0 1 &mpic 6 1
+			9800 0 0 2 &mpic 7 1
+			9800 0 0 3 &mpic 4 1
+			9800 0 0 4 &mpic 5 1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 e2000000 0 00800000>;
+		clock-frequency = <3f940aa>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008000 1000>;
+		compatible = "fsl,mpc8540-pci";
+		device_type = "pci";
+	};
+
+	/* PCI Express */
+	pcie@e000a000 {
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+
+			/* IDSEL 0x0 (PEX) */
+			00000 0 0 1 &mpic 0 1
+			00000 0 0 2 &mpic 1 1
+			00000 0 0 3 &mpic 2 1
+			00000 0 0 4 &mpic 3 1>;
+
+		interrupt-parent = <&mpic>;
+		interrupts = <1a 2>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 a0000000 a0000000 0 10000000
+			  01000000 0 00000000 e2800000 0 00800000>;
+		clock-frequency = <1fca055>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e000a000 1000>;
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		pcie@0 {
+			reg = <0 0 0 0 0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <02000000 0 a0000000
+				  02000000 0 a0000000
+				  0 10000000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00800000>;
+		};
+	};
 };

arch/powerpc/boot/dts/mpc8572ds.dts

@@ -0,0 +1,404 @@
+/*
+ * MPC8572 DS Device Tree Source
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/ {
+	model = "fsl,MPC8572DS";
+	compatible = "fsl,MPC8572DS";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8572@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <20>;	// 32 bytes
+			i-cache-line-size = <20>;	// 32 bytes
+			d-cache-size = <8000>;		// L1, 32K
+			i-cache-size = <8000>;		// L1, 32K
+			timebase-frequency = <0>;
+			bus-frequency = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <00000000 00000000>;	// Filled by U-Boot
+	};
+
+	soc8572@ffe00000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		ranges = <00000000 ffe00000 00100000>;
+		reg = <ffe00000 00001000>;	// CCSRBAR & soc regs, remove once parse code for immrbase fixed
+		bus-frequency = <0>;		// Filled out by uboot.
+
+		memory-controller@2000 {
+			compatible = "fsl,mpc8572-memory-controller";
+			reg = <2000 1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <12 2>;
+		};
+
+		memory-controller@6000 {
+			compatible = "fsl,mpc8572-memory-controller";
+			reg = <6000 1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <12 2>;
+		};
+
+		l2-cache-controller@20000 {
+			compatible = "fsl,mpc8572-l2-cache-controller";
+			reg = <20000 1000>;
+			cache-line-size = <20>;	// 32 bytes
+			cache-size = <80000>;	// L2, 512K
+			interrupt-parent = <&mpic>;
+			interrupts = <10 2>;
+		};
+
+		i2c@3000 {
+			device_type = "i2c";
+			compatible = "fsl-i2c";
+			reg = <3000 100>;
+			interrupts = <2b 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			device_type = "i2c";
+			compatible = "fsl-i2c";
+			reg = <3100 100>;
+			interrupts = <2b 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		mdio@24520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			device_type = "mdio";
+			compatible = "gianfar";
+			reg = <24520 20>;
+			phy0: ethernet-phy@0 {
+				interrupt-parent = <&mpic>;
+				interrupts = <a 1>;
+				reg = <0>;
+			};
+			phy1: ethernet-phy@1 {
+				interrupt-parent = <&mpic>;
+				interrupts = <a 1>;
+				reg = <1>;
+			};
+			phy2: ethernet-phy@2 {
+				interrupt-parent = <&mpic>;
+				interrupts = <a 1>;
+				reg = <2>;
+			};
+			phy3: ethernet-phy@3 {
+				interrupt-parent = <&mpic>;
+				interrupts = <a 1>;
+				reg = <3>;
+			};
+		};
+
+		ethernet@24000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <24000 1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <1d 2 1e 2 22 2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy0>;
+			phy-connection-type = "rgmii-id";
+		};
+
+		ethernet@25000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <25000 1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <23 2 24 2 28 2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy1>;
+			phy-connection-type = "rgmii-id";
+		};
+
+		ethernet@26000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <26000 1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <1f 2 20 2 21 2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy2>;
+			phy-connection-type = "rgmii-id";
+		};
+
+		ethernet@27000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "gianfar";
+			reg = <27000 1000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <25 2 26 2 27 2>;
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy3>;
+			phy-connection-type = "rgmii-id";
+		};
+
+		serial@4500 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <4500 100>;
+			clock-frequency = <0>;
+			interrupts = <2a 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		serial@4600 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <4600 100>;
+			clock-frequency = <0>;
+			interrupts = <2a 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		global-utilities@e0000 {	//global utilities block
+			compatible = "fsl,mpc8572-guts";
+			reg = <e0000 1000>;
+			fsl,has-rstcr;
+		};
+
+		mpic: pic@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+			big-endian;
+		};
+	};
+
+	pcie@ffe08000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <ffe08000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 ffc00000 0 00010000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		interrupt-map-mask = <fb00 0 0 0>;
+		interrupt-map = <
+			/* IDSEL 0x11 - PCI slot 1 */
+			8800 0 0 1 &mpic 2 1
+			8800 0 0 2 &mpic 3 1
+			8800 0 0 3 &mpic 4 1
+			8800 0 0 4 &mpic 1 1
+
+			/* IDSEL 0x12 - PCI slot 2 */
+			9000 0 0 1 &mpic 3 1
+			9000 0 0 2 &mpic 4 1
+			9000 0 0 3 &mpic 1 1
+			9000 0 0 4 &mpic 2 1
+
+			// IDSEL 0x1c  USB
+			e000 0 0 0 &i8259 c 2
+			e100 0 0 0 &i8259 9 2
+			e200 0 0 0 &i8259 a 2
+			e300 0 0 0 &i8259 b 2
+
+			// IDSEL 0x1d  Audio
+			e800 0 0 0 &i8259 6 2
+
+			// IDSEL 0x1e Legacy
+			f000 0 0 0 &i8259 7 2
+			f100 0 0 0 &i8259 7 2
+
+			// IDSEL 0x1f IDE/SATA
+			f800 0 0 0 &i8259 e 2
+			f900 0 0 0 &i8259 5 2
+
+			>;
+
+		pcie@0 {
+			reg = <0 0 0 0 0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <02000000 0 80000000
+				  02000000 0 80000000
+				  0 20000000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00100000>;
+			uli1575@0 {
+				reg = <0 0 0 0 0>;
+				#size-cells = <2>;
+				#address-cells = <3>;
+				ranges = <02000000 0 80000000
+					  02000000 0 80000000
+					  0 20000000
+
+					  01000000 0 00000000
+					  01000000 0 00000000
+					  0 00100000>;
+				isa@1e {
+					device_type = "isa";
+					#interrupt-cells = <2>;
+					#size-cells = <1>;
+					#address-cells = <2>;
+					reg = <f000 0 0 0 0>;
+					ranges = <1 0 01000000 0 0
+						  00001000>;
+					interrupt-parent = <&i8259>;
+
+					i8259: interrupt-controller@20 {
+						reg = <1 20 2
+						       1 a0 2
+						       1 4d0 2>;
+						interrupt-controller;
+						device_type = "interrupt-controller";
+						#address-cells = <0>;
+						#interrupt-cells = <2>;
+						compatible = "chrp,iic";
+						interrupts = <9 2>;
+						interrupt-parent = <&mpic>;
+					};
+
+					i8042@60 {
+						#size-cells = <0>;
+						#address-cells = <1>;
+						reg = <1 60 1 1 64 1>;
+						interrupts = <1 3 c 3>;
+						interrupt-parent =
+							<&i8259>;
+
+						keyboard@0 {
+							reg = <0>;
+							compatible = "pnpPNP,303";
+						};
+
+						mouse@1 {
+							reg = <1>;
+							compatible = "pnpPNP,f03";
+						};
+					};
+
+					rtc@70 {
+						compatible = "pnpPNP,b00";
+						reg = <1 70 2>;
+					};
+
+					gpio@400 {
+						reg = <1 400 80>;
+					};
+				};
+			};
+		};
+
+	};
+
+	pcie@ffe09000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <ffe09000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 a0000000 a0000000 0 20000000
+			  01000000 0 00000000 ffc10000 0 00010000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <1a 2>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 4 1
+			0000 0 0 2 &mpic 5 1
+			0000 0 0 3 &mpic 6 1
+			0000 0 0 4 &mpic 7 1
+			>;
+		pcie@0 {
+			reg = <0 0 0 0 0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <02000000 0 a0000000
+				  02000000 0 a0000000
+				  0 20000000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00100000>;
+		};
+	};
+
+	pcie@ffe0a000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <ffe0a000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 c0000000 c0000000 0 20000000
+			  01000000 0 00000000 ffc20000 0 00010000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <1b 2>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 0 1
+			0000 0 0 2 &mpic 1 1
+			0000 0 0 3 &mpic 2 1
+			0000 0 0 4 &mpic 3 1
+			>;
+		pcie@0 {
+			reg = <0 0 0 0 0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <02000000 0 c0000000
+				  02000000 0 c0000000
+				  0 20000000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00100000>;
+		};
+	};
+};

arch/powerpc/boot/dts/mpc8610_hpcd.dts

@@ -0,0 +1,191 @@
+/*
+ * MPC8610 HPCD Device Tree Source
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under the terms of the GNU General Public License Version 2 as published
+ * by the Free Software Foundation.
+ */
+
+
+/ {
+	model = "MPC8610HPCD";
+	compatible = "fsl,MPC8610HPCD";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8610@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <d# 32>;	// bytes
+			i-cache-line-size = <d# 32>;	// bytes
+			d-cache-size = <8000>;		// L1, 32K
+			i-cache-size = <8000>;		// L1, 32K
+			timebase-frequency = <0>;	// 33 MHz, from uboot
+			bus-frequency = <0>;		// From uboot
+			clock-frequency = <0>;		// From uboot
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <00000000 20000000>;	// 512M at 0x0
+	};
+
+	soc@e0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		#interrupt-cells = <2>;
+		device_type = "soc";
+		ranges = <0 e0000000 00100000>;
+		reg = <e0000000 1000>;
+		bus-frequency = <0>;
+
+		i2c@3000 {
+			device_type = "i2c";
+			compatible = "fsl-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3000 100>;
+			interrupts = <2b 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			device_type = "i2c";
+			compatible = "fsl-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3100 100>;
+			interrupts = <2b 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		serial@4500 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <4500 100>;
+			clock-frequency = <0>;
+			interrupts = <2a 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		serial@4600 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <4600 100>;
+			clock-frequency = <0>;
+			interrupts = <1c 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+
+		mpic: interrupt-controller@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+			big-endian;
+		};
+
+		global-utilities@e0000 {
+			compatible = "fsl,mpc8610-guts";
+			reg = <e0000 1000>;
+			fsl,has-rstcr;
+		};
+	};
+
+	pci@e0008000 {
+		compatible = "fsl,mpc8610-pci";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e0008000 1000>;
+		bus-range = <0 0>;
+		ranges = <02000000 0 80000000 80000000 0 10000000
+			  01000000 0 00000000 e1000000 0 00100000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x11 */
+			8800 0 0 1 &mpic 4 1
+			8800 0 0 2 &mpic 5 1
+			8800 0 0 3 &mpic 6 1
+			8800 0 0 4 &mpic 7 1
+
+			/* IDSEL 0x12 */
+			9000 0 0 1 &mpic 5 1
+			9000 0 0 2 &mpic 6 1
+			9000 0 0 3 &mpic 7 1
+			9000 0 0 4 &mpic 4 1
+			>;
+	};
+
+	pcie@e000a000 {
+		compatible = "fsl,mpc8641-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <e000a000 1000>;
+		bus-range = <1 3>;
+		ranges = <02000000 0 a0000000 a0000000 0 10000000
+			  01000000 0 00000000 e3000000 0 00100000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <1a 2>;
+		interrupt-map-mask = <f800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x1b */
+			d800 0 0 1 &mpic 2 1
+
+			/* IDSEL 0x1c*/
+			e000 0 0 1 &mpic 1 1
+			e000 0 0 2 &mpic 1 1
+			e000 0 0 3 &mpic 1 1
+			e000 0 0 4 &mpic 1 1
+
+			/* IDSEL 0x1f */
+			f800 0 0 1 &mpic 3 0
+			f800 0 0 2 &mpic 0 1
+		>;
+
+		pcie@0 {
+			reg = <0 0 0 0 0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <02000000 0 a0000000
+				  02000000 0 a0000000
+				  0 10000000
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00100000>;
+			uli1575@0 {
+				reg = <0 0 0 0 0>;
+				#size-cells = <2>;
+				#address-cells = <3>;
+				ranges = <02000000 0 a0000000
+					  02000000 0 a0000000
+					  0 10000000
+					  01000000 0 00000000
+					  01000000 0 00000000
+					  0 00100000>;
+			};
+		};
+	};
+};

arch/powerpc/boot/dts/mpc8641_hpcn.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <0>;	// 33 MHz, from uboot
 			bus-frequency = <0>;		// From uboot
 			clock-frequency = <0>;		// From uboot
-			32-bit;
 		};
 		PowerPC,8641@1 {
 			device_type = "cpu";
@@ -42,7 +41,6 @@
 			timebase-frequency = <0>;	// 33 MHz, from uboot
 			bus-frequency = <0>;		// From uboot
 			clock-frequency = <0>;		// From uboot
-			32-bit;
 		};
 	};
 
@@ -54,13 +52,8 @@
 	soc8641@f8000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
-		ranges = <00001000 f8001000 000ff000
-			  80000000 80000000 20000000
-			  e2000000 e2000000 00100000
-			  a0000000 a0000000 20000000
-			  e3000000 e3000000 00100000>;
+		ranges = <00000000 f8000000 00100000>;
 		reg = <f8000000 00001000>;	// CCSRBAR
 		bus-frequency = <0>;
 
@@ -211,50 +204,81 @@
 			interrupt-parent = <&mpic>;
 		};
 
-		pcie@8000 {
-			compatible = "fsl,mpc8641-pcie";
-			device_type = "pci";
-			#interrupt-cells = <1>;
+		mpic: pic@40000 {
+			clock-frequency = <0>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <40000 40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+			big-endian;
+		};
+
+		global-utilities@e0000 {
+			compatible = "fsl,mpc8641-guts";
+			reg = <e0000 1000>;
+			fsl,has-rstcr;
+		};
+	};
+
+	pcie@f8008000 {
+		compatible = "fsl,mpc8641-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <f8008000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 80000000 80000000 0 20000000
+			  01000000 0 00000000 e2000000 0 00100000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <18 2>;
+		interrupt-map-mask = <fb00 0 0 0>;
+		interrupt-map = <
+			/* IDSEL 0x11 */
+			8800 0 0 1 &i8259 9 2
+			8800 0 0 2 &i8259 a 2
+			8800 0 0 3 &i8259 b 2
+			8800 0 0 4 &i8259 c 2
+
+			/* IDSEL 0x12 */
+			9000 0 0 1 &i8259 a 2
+			9000 0 0 2 &i8259 b 2
+			9000 0 0 3 &i8259 c 2
+			9000 0 0 4 &i8259 9 2
+
+			// IDSEL 0x1c  USB
+			e000 0 0 0 &i8259 c 2
+			e100 0 0 0 &i8259 9 2
+			e200 0 0 0 &i8259 a 2
+			e300 0 0 0 &i8259 b 2
+
+			// IDSEL 0x1d  Audio
+			e800 0 0 0 &i8259 6 2
+
+			// IDSEL 0x1e Legacy
+			f000 0 0 0 &i8259 7 2
+			f100 0 0 0 &i8259 7 2
+
+			// IDSEL 0x1f IDE/SATA
+			f800 0 0 0 &i8259 e 2
+			f900 0 0 0 &i8259 5 2
+			>;
+
+		pcie@0 {
+			reg = <0 0 0 0 0>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <8000 1000>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 80000000 80000000 0 20000000
-				  01000000 0 00000000 e2000000 0 00100000>;
-			clock-frequency = <1fca055>;
-			interrupt-parent = <&mpic>;
-			interrupts = <18 2>;
-			interrupt-map-mask = <fb00 0 0 0>;
-			interrupt-map = <
-				/* IDSEL 0x11 */
-				8800 0 0 1 &i8259 9 2
-				8800 0 0 2 &i8259 a 2
-				8800 0 0 3 &i8259 b 2
-				8800 0 0 4 &i8259 c 2
-
-				/* IDSEL 0x12 */
-				9000 0 0 1 &i8259 a 2
-				9000 0 0 2 &i8259 b 2
-				9000 0 0 3 &i8259 c 2
-				9000 0 0 4 &i8259 9 2
-
-				// IDSEL 0x1c  USB
-				e000 0 0 0 &i8259 c 2
-				e100 0 0 0 &i8259 9 2
-				e200 0 0 0 &i8259 a 2
-				e300 0 0 0 &i8259 b 2
-
-				// IDSEL 0x1d  Audio
-				e800 0 0 0 &i8259 6 2
-
-				// IDSEL 0x1e Legacy
-				f000 0 0 0 &i8259 7 2
-				f100 0 0 0 &i8259 7 2
-
-				// IDSEL 0x1f IDE/SATA
-				f800 0 0 0 &i8259 e 2
-				f900 0 0 0 &i8259 5 2
-				>;
+			device_type = "pci";
+			ranges = <02000000 0 80000000
+				  02000000 0 80000000
+				  0 20000000
+
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00100000>;
 			uli1575@0 {
 				reg = <0 0 0 0 0>;
 				#size-cells = <2>;
@@ -265,111 +289,96 @@
 					  01000000 0 00000000
 					  01000000 0 00000000
 					  0 00100000>;
+				isa@1e {
+					device_type = "isa";
+					#interrupt-cells = <2>;
+					#size-cells = <1>;
+					#address-cells = <2>;
+					reg = <f000 0 0 0 0>;
+					ranges = <1 0 01000000 0 0
+						  00001000>;
+					interrupt-parent = <&i8259>;
 
-				pci_bridge@0 {
-					reg = <0 0 0 0 0>;
-					#size-cells = <2>;
-					#address-cells = <3>;
-					ranges = <02000000 0 80000000
-						  02000000 0 80000000
-						  0 20000000
-						  01000000 0 00000000
-						  01000000 0 00000000
-						  0 00100000>;
-
-					isa@1e {
-						device_type = "isa";
+					i8259: interrupt-controller@20 {
+						reg = <1 20 2
+						       1 a0 2
+						       1 4d0 2>;
+						interrupt-controller;
+						device_type = "interrupt-controller";
+						#address-cells = <0>;
 						#interrupt-cells = <2>;
-						#size-cells = <1>;
-						#address-cells = <2>;
-						reg = <f000 0 0 0 0>;
-						ranges = <1 0 01000000 0 0
-							  00001000>;
-						interrupt-parent = <&i8259>;
-
-						i8259: interrupt-controller@20 {
-							reg = <1 20 2
-							       1 a0 2
-							       1 4d0 2>;
-							clock-frequency = <0>;
-							interrupt-controller;
-							device_type = "interrupt-controller";
-							#address-cells = <0>;
-							#interrupt-cells = <2>;
-							built-in;
-							compatible = "chrp,iic";
-							interrupts = <9 2>;
-							interrupt-parent =
-								<&mpic>;
-						};
+						compatible = "chrp,iic";
+						interrupts = <9 2>;
+						interrupt-parent = <&mpic>;
+					};
 
-						i8042@60 {
-							#size-cells = <0>;
-							#address-cells = <1>;
-							reg = <1 60 1 1 64 1>;
-							interrupts = <1 3 c 3>;
-							interrupt-parent =
-								<&i8259>;
-
-							keyboard@0 {
-								reg = <0>;
-								compatible = "pnpPNP,303";
-							};
-
-							mouse@1 {
-								reg = <1>;
-								compatible = "pnpPNP,f03";
-							};
-						};
+					i8042@60 {
+						#size-cells = <0>;
+						#address-cells = <1>;
+						reg = <1 60 1 1 64 1>;
+						interrupts = <1 3 c 3>;
+						interrupt-parent =
+							<&i8259>;
 
-						rtc@70 {
-							compatible =
-								"pnpPNP,b00";
-							reg = <1 70 2>;
+						keyboard@0 {
+							reg = <0>;
+							compatible = "pnpPNP,303";
 						};
 
-						gpio@400 {
-							reg = <1 400 80>;
+						mouse@1 {
+							reg = <1>;
+							compatible = "pnpPNP,f03";
 						};
 					};
+
+					rtc@70 {
+						compatible =
+							"pnpPNP,b00";
+						reg = <1 70 2>;
+					};
+
+					gpio@400 {
+						reg = <1 400 80>;
+					};
 				};
 			};
-
 		};
 
-		pcie@9000 {
-			compatible = "fsl,mpc8641-pcie";
-			device_type = "pci";
-			#interrupt-cells = <1>;
+	};
+
+	pcie@f8009000 {
+		compatible = "fsl,mpc8641-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <f8009000 1000>;
+		bus-range = <0 ff>;
+		ranges = <02000000 0 a0000000 a0000000 0 20000000
+			  01000000 0 00000000 e3000000 0 00100000>;
+		clock-frequency = <1fca055>;
+		interrupt-parent = <&mpic>;
+		interrupts = <19 2>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 4 1
+			0000 0 0 2 &mpic 5 1
+			0000 0 0 3 &mpic 6 1
+			0000 0 0 4 &mpic 7 1
+			>;
+		pcie@0 {
+			reg = <0 0 0 0 0>;
 			#size-cells = <2>;
 			#address-cells = <3>;
-			reg = <9000 1000>;
-			bus-range = <0 ff>;
-			ranges = <02000000 0 a0000000 a0000000 0 20000000
-				  01000000 0 00000000 e3000000 0 00100000>;
-			clock-frequency = <1fca055>;
-			interrupt-parent = <&mpic>;
-			interrupts = <19 2>;
-			interrupt-map-mask = <f800 0 0 7>;
-			interrupt-map = <
-				/* IDSEL 0x0 */
-				0000 0 0 1 &mpic 4 1
-				0000 0 0 2 &mpic 5 1
-				0000 0 0 3 &mpic 6 1
-				0000 0 0 4 &mpic 7 1
-				>;
-		};
+			device_type = "pci";
+			ranges = <02000000 0 a0000000
+				  02000000 0 a0000000
+				  0 20000000
 
-		mpic: pic@40000 {
-			clock-frequency = <0>;
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <2>;
-			reg = <40000 40000>;
-			built-in;
-			compatible = "chrp,open-pic";
-			device_type = "open-pic";
-			big-endian;
+				  01000000 0 00000000
+				  01000000 0 00000000
+				  0 00100000>;
 		};
 	};
 };

arch/powerpc/boot/dts/mpc866ads.dts

@@ -30,7 +30,6 @@
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
-			32-bit;
 			interrupts = <f 2>;	// decrementer interrupt
 			interrupt-parent = <&Mpc8xx_pic>;
 		};
@@ -44,7 +43,6 @@
 	soc866@ff000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
 		ranges = <0 ff000000 00100000>;
 		reg = <ff000000 00000200>;
@@ -78,7 +76,6 @@
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <0 24>;
-			built-in;
 			device_type = "mpc8xx-pic";
 			compatible = "CPM";
 		};
@@ -86,7 +83,6 @@
 		cpm@ff000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-			#interrupt-cells = <2>;
 			device_type = "cpm";
 			model = "CPM";
 			ranges = <0 0 4000>;
@@ -103,7 +99,6 @@
 				interrupts = <5 2 0 2>;
 				interrupt-parent = <&Mpc8xx_pic>;
 				reg = <930 20>;
-				built-in;
 				device_type = "cpm-pic";
 				compatible = "CPM";
 			};

arch/powerpc/boot/dts/mpc885ads.dts

@@ -2,6 +2,7 @@
  * MPC885 ADS Device Tree Source
  *
  * Copyright 2006 MontaVista Software, Inc.
+ * Copyright 2007 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute  it and/or modify it
  * under  the terms of  the GNU General  Public License as published by the
@@ -12,7 +13,7 @@
 
 / {
 	model = "MPC885ADS";
-	compatible = "mpc8xx";
+	compatible = "fsl,mpc885ads";
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -23,161 +24,199 @@
 		PowerPC,885@0 {
 			device_type = "cpu";
 			reg = <0>;
-			d-cache-line-size = <20>;	// 32 bytes
-			i-cache-line-size = <20>;	// 32 bytes
-			d-cache-size = <2000>;		// L1, 8K
-			i-cache-size = <2000>;		// L1, 8K
+			d-cache-line-size = <d#16>;
+			i-cache-line-size = <d#16>;
+			d-cache-size = <d#8192>;
+			i-cache-size = <d#8192>;
 			timebase-frequency = <0>;
 			bus-frequency = <0>;
 			clock-frequency = <0>;
-			32-bit;
 			interrupts = <f 2>;	// decrementer interrupt
-			interrupt-parent = <&Mpc8xx_pic>;
+			interrupt-parent = <&PIC>;
 		};
 	};
 
 	memory {
 		device_type = "memory";
-		reg = <00000000 800000>;
+		reg = <0 0>;
 	};
 
-	soc885@ff000000 {
+	localbus@ff000100 {
+		compatible = "fsl,mpc885-localbus", "fsl,pq1-localbus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <ff000100 40>;
+
+		ranges = <
+			0 0 fe000000 00800000
+			1 0 ff080000 00008000
+			5 0 ff0a0000 00008000
+		>;
+
+		flash@0,0 {
+			compatible = "jedec-flash";
+			reg = <0 0 800000>;
+			bank-width = <4>;
+			device-width = <1>;
+		};
+
+		board-control@1,0 {
+			reg = <1 0 20 5 300 4>;
+			compatible = "fsl,mpc885ads-bcsr";
+		};
+	};
+
+	soc@ff000000 {
+		compatible = "fsl,mpc885", "fsl,pq1-soc";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <2>;
 		device_type = "soc";
-		ranges = <0 ff000000 00100000>;
-		reg = <ff000000 00000200>;
+		ranges = <0 ff000000 00004000>;
 		bus-frequency = <0>;
-		mdio@e80 {
-			device_type = "mdio";
-			compatible = "fs_enet";
-			reg = <e80 8>;
+
+		// Temporary -- will go away once kernel uses ranges for get_immrbase().
+		reg = <ff000000 4000>;
+
+		mdio@e00 {
+			compatible = "fsl,mpc885-fec-mdio", "fsl,pq1-fec-mdio";
+			reg = <e00 188>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			Phy0: ethernet-phy@0 {
+
+			PHY0: ethernet-phy@0 {
 				reg = <0>;
 				device_type = "ethernet-phy";
 			};
-			Phy1: ethernet-phy@1 {
+
+			PHY1: ethernet-phy@1 {
 				reg = <1>;
 				device_type = "ethernet-phy";
 			};
-			Phy2: ethernet-phy@2 {
+
+			PHY2: ethernet-phy@2 {
 				reg = <2>;
 				device_type = "ethernet-phy";
 			};
 		};
 
-		fec@e00 {
+		ethernet@e00 {
 			device_type = "network";
-			compatible = "fs_enet";
-			model = "FEC";
-			device-id = <1>;
+			compatible = "fsl,mpc885-fec-enet",
+			             "fsl,pq1-fec-enet";
 			reg = <e00 188>;
-			mac-address = [ 00 00 0C 00 01 FD ];
+			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <3 1>;
-			interrupt-parent = <&Mpc8xx_pic>;
-			phy-handle = <&Phy1>;
+			interrupt-parent = <&PIC>;
+			phy-handle = <&PHY0>;
+			linux,network-index = <0>;
 		};
 
-		fec@1e00 {
+		ethernet@1e00 {
 			device_type = "network";
-			compatible = "fs_enet";
-			model = "FEC";
-			device-id = <2>;
+			compatible = "fsl,mpc885-fec-enet",
+			             "fsl,pq1-fec-enet";
 			reg = <1e00 188>;
-			mac-address = [ 00 00 0C 00 02 FD ];
+			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <7 1>;
-			interrupt-parent = <&Mpc8xx_pic>;
-			phy-handle = <&Phy2>;
+			interrupt-parent = <&PIC>;
+			phy-handle = <&PHY1>;
+			linux,network-index = <1>;
 		};
 
-		Mpc8xx_pic: pic@ff000000 {
+		PIC: interrupt-controller@0 {
 			interrupt-controller;
-			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <0 24>;
-			built-in;
-			device_type = "mpc8xx-pic";
-			compatible = "CPM";
+			compatible = "fsl,mpc885-pic", "fsl,pq1-pic";
 		};
 
-		pcmcia@0080 {
+		pcmcia@80 {
 			#address-cells = <3>;
 			#interrupt-cells = <1>;
 			#size-cells = <2>;
 			compatible = "fsl,pq-pcmcia";
 			device_type = "pcmcia";
 			reg = <80 80>;
-			interrupt-parent = <&Mpc8xx_pic>;
+			interrupt-parent = <&PIC>;
 			interrupts = <d 1>;
 		};
 
-		cpm@ff000000 {
+		cpm@9c0 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-			#interrupt-cells = <2>;
-			device_type = "cpm";
-			model = "CPM";
-			ranges = <0 0 4000>;
-			reg = <860 f0>;
+			compatible = "fsl,mpc885-cpm", "fsl,cpm1";
 			command-proc = <9c0>;
-			brg-frequency = <0>;
-			interrupts = <0 2>;	// cpm error interrupt
-			interrupt-parent = <&Cpm_pic>;
+			interrupts = <0>;	// cpm error interrupt
+			interrupt-parent = <&CPM_PIC>;
+			reg = <9c0 40>;
+			ranges;
+
+			muram@2000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 2000 2000>;
 
-			Cpm_pic: pic@930 {
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0 1c00>;
+				};
+			};
+
+			brg@9f0 {
+				compatible = "fsl,mpc885-brg",
+				             "fsl,cpm1-brg",
+				             "fsl,cpm-brg";
+				reg = <9f0 10>;
+			};
+
+			CPM_PIC: interrupt-controller@930 {
 				interrupt-controller;
-				#address-cells = <0>;
-				#interrupt-cells = <2>;
+				#interrupt-cells = <1>;
 				interrupts = <5 2 0 2>;
-				interrupt-parent = <&Mpc8xx_pic>;
+				interrupt-parent = <&PIC>;
 				reg = <930 20>;
-				built-in;
-				device_type = "cpm-pic";
-				compatible = "CPM";
+				compatible = "fsl,mpc885-cpm-pic",
+				             "fsl,cpm1-pic";
 			};
 
-			smc@a80 {
+			serial@a80 {
 				device_type = "serial";
-				compatible = "cpm_uart";
-				model = "SMC";
-				device-id = <1>;
+				compatible = "fsl,mpc885-smc-uart",
+				             "fsl,cpm1-smc-uart";
 				reg = <a80 10 3e80 40>;
-				clock-setup = <00ffffff 0>;
-				rx-clock = <1>;
-				tx-clock = <1>;
-				current-speed = <0>;
-				interrupts = <4 3>;
-				interrupt-parent = <&Cpm_pic>;
+				interrupts = <4>;
+				interrupt-parent = <&CPM_PIC>;
+				fsl,cpm-brg = <1>;
+				fsl,cpm-command = <0090>;
 			};
 
-			smc@a90 {
+			serial@a90 {
 				device_type = "serial";
-				compatible = "cpm_uart";
-				model = "SMC";
-				device-id = <2>;
-				reg = <a90 20 3f80 40>;
-				clock-setup = <ff00ffff 90000>;
-				rx-clock = <2>;
-				tx-clock = <2>;
-				current-speed = <0>;
-				interrupts = <3 3>;
-				interrupt-parent = <&Cpm_pic>;
+				compatible = "fsl,mpc885-smc-uart",
+				             "fsl,cpm1-smc-uart";
+				reg = <a90 10 3f80 40>;
+				interrupts = <3>;
+				interrupt-parent = <&CPM_PIC>;
+				fsl,cpm-brg = <2>;
+				fsl,cpm-command = <00d0>;
 			};
 
-			scc@a40 {
+			ethernet@a40 {
 				device_type = "network";
-				compatible = "fs_enet";
-				model = "SCC";
-				device-id = <3>;
-				reg = <a40 18 3e00 80>;
-				mac-address = [ 00 00 0C 00 03 FD ];
-				interrupts = <1c 3>;
-				interrupt-parent = <&Cpm_pic>;
-				phy-handle = <&Phy2>;
+				compatible = "fsl,mpc885-scc-enet",
+				             "fsl,cpm1-scc-enet";
+				reg = <a40 18 3e00 100>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+				interrupts = <1c>;
+				interrupt-parent = <&CPM_PIC>;
+				phy-handle = <&PHY2>;
+				fsl,cpm-command = <0080>;
+				linux,network-index = <2>;
 			};
 		};
 	};
+
+	chosen {
+		linux,stdout-path = "/soc/cpm/serial@a80";
+	};
 };

arch/powerpc/boot/dts/pq2fads.dts

@@ -0,0 +1,240 @@
+/*
+ * Device Tree for the PQ2FADS-ZU board with an MPC8280 chip.
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/ {
+	model = "pq2fads";
+	compatible = "fsl,pq2fads";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <d#32>;
+			i-cache-line-size = <d#32>;
+			d-cache-size = <d#16384>;
+			i-cache-size = <d#16384>;
+			timebase-frequency = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	localbus@f0010100 {
+		compatible = "fsl,mpc8280-localbus",
+		             "fsl,pq2-localbus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <f0010100 60>;
+
+		ranges = <0 0 fe000000 00800000
+		          1 0 f4500000 00008000
+		          8 0 f8200000 00008000>;
+
+		flash@0,0 {
+			compatible = "jedec-flash";
+			reg = <0 0 800000>;
+			bank-width = <4>;
+			device-width = <1>;
+		};
+
+		bcsr@1,0 {
+			reg = <1 0 20>;
+			compatible = "fsl,pq2fads-bcsr";
+		};
+
+		PCI_PIC: pic@8,0 {
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			reg = <8 0 8>;
+			compatible = "fsl,pq2ads-pci-pic";
+			interrupt-parent = <&PIC>;
+			interrupts = <18 8>;
+		};
+	};
+
+	pci@f0010800 {
+		device_type = "pci";
+		reg = <f0010800 10c f00101ac 8 f00101c4 8>;
+		compatible = "fsl,mpc8280-pci", "fsl,pq2-pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		clock-frequency = <d#66000000>;
+		interrupt-map-mask = <f800 0 0 7>;
+		interrupt-map = <
+		                /* IDSEL 0x16 */
+		                 b000 0 0 1 &PCI_PIC 0
+		                 b000 0 0 2 &PCI_PIC 1
+		                 b000 0 0 3 &PCI_PIC 2
+		                 b000 0 0 4 &PCI_PIC 3
+
+		                /* IDSEL 0x17 */
+		                 b800 0 0 1 &PCI_PIC 4
+		                 b800 0 0 2 &PCI_PIC 5
+		                 b800 0 0 3 &PCI_PIC 6
+		                 b800 0 0 4 &PCI_PIC 7
+
+		                /* IDSEL 0x18 */
+		                 c000 0 0 1 &PCI_PIC 8
+		                 c000 0 0 2 &PCI_PIC 9
+		                 c000 0 0 3 &PCI_PIC a
+		                 c000 0 0 4 &PCI_PIC b>;
+
+		interrupt-parent = <&PIC>;
+		interrupts = <12 8>;
+		ranges = <42000000 0 80000000 80000000 0 20000000
+		          02000000 0 a0000000 a0000000 0 20000000
+		          01000000 0 00000000 f6000000 0 02000000>;
+	};
+
+	soc@f0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,mpc8280", "fsl,pq2-soc";
+		ranges = <00000000 f0000000 00053000>;
+
+		// Temporary -- will go away once kernel uses ranges for get_immrbase().
+		reg = <f0000000 00053000>;
+
+		cpm@119c0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#interrupt-cells = <2>;
+			compatible = "fsl,mpc8280-cpm", "fsl,cpm2";
+			reg = <119c0 30>;
+			ranges;
+
+			muram@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0 10000>;
+
+				data@0 {
+					compatible = "fsl,cpm-muram-data";
+					reg = <0 2000 9800 800>;
+				};
+			};
+
+			brg@119f0 {
+				compatible = "fsl,mpc8280-brg",
+				             "fsl,cpm2-brg",
+				             "fsl,cpm-brg";
+				reg = <119f0 10 115f0 10>;
+			};
+
+			serial@11a00 {
+				device_type = "serial";
+				compatible = "fsl,mpc8280-scc-uart",
+				             "fsl,cpm2-scc-uart";
+				reg = <11a00 20 8000 100>;
+				interrupts = <28 8>;
+				interrupt-parent = <&PIC>;
+				fsl,cpm-brg = <1>;
+				fsl,cpm-command = <00800000>;
+			};
+
+			serial@11a20 {
+				device_type = "serial";
+				compatible = "fsl,mpc8280-scc-uart",
+				             "fsl,cpm2-scc-uart";
+				reg = <11a20 20 8100 100>;
+				interrupts = <29 8>;
+				interrupt-parent = <&PIC>;
+				fsl,cpm-brg = <2>;
+				fsl,cpm-command = <04a00000>;
+			};
+
+			ethernet@11320 {
+				device_type = "network";
+				compatible = "fsl,mpc8280-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <11320 20 8500 100 113b0 1>;
+				interrupts = <21 8>;
+				interrupt-parent = <&PIC>;
+				phy-handle = <&PHY0>;
+				linux,network-index = <0>;
+				fsl,cpm-command = <16200300>;
+			};
+
+			ethernet@11340 {
+				device_type = "network";
+				compatible = "fsl,mpc8280-fcc-enet",
+				             "fsl,cpm2-fcc-enet";
+				reg = <11340 20 8600 100 113d0 1>;
+				interrupts = <22 8>;
+				interrupt-parent = <&PIC>;
+				phy-handle = <&PHY1>;
+				linux,network-index = <1>;
+				fsl,cpm-command = <1a400300>;
+				local-mac-address = [00 e0 0c 00 79 01];
+			};
+
+			mdio@10d40 {
+				device_type = "mdio";
+				compatible = "fsl,pq2fads-mdio-bitbang",
+				             "fsl,mpc8280-mdio-bitbang",
+				             "fsl,cpm2-mdio-bitbang";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10d40 14>;
+				fsl,mdio-pin = <9>;
+				fsl,mdc-pin = <a>;
+
+				PHY0: ethernet-phy@0 {
+					interrupt-parent = <&PIC>;
+					interrupts = <19 2>;
+					reg = <0>;
+					device_type = "ethernet-phy";
+				};
+
+				PHY1: ethernet-phy@1 {
+					interrupt-parent = <&PIC>;
+					interrupts = <19 2>;
+					reg = <3>;
+					device_type = "ethernet-phy";
+				};
+			};
+
+			usb@11b60 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,mpc8280-usb",
+				             "fsl,cpm2-usb";
+				reg = <11b60 18 8b00 100>;
+				interrupt-parent = <&PIC>;
+				interrupts = <b 8>;
+				fsl,cpm-command = <2e600000>;
+			};
+		};
+
+		PIC: interrupt-controller@10c00 {
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			reg = <10c00 80>;
+			compatible = "fsl,mpc8280-pic", "fsl,cpm2-pic";
+		};
+
+	};
+
+	chosen {
+		linux,stdout-path = "/soc/cpm/serial@11a00";
+	};
+};

arch/powerpc/boot/dts/prpmc2800.dts

@@ -9,10 +9,6 @@
  *
  * Property values that are labeled as "Default" will be updated by bootwrapper
  * if it can determine the exact PrPMC type.
- *
- * To build:
- *   dtc -I dts -O asm -o prpmc2800.S -b 0 prpmc2800.dts
- *   dtc -I dts -O dtb -o prpmc2800.dtb -b 0 prpmc2800.dts
  */
 
 / {
@@ -47,7 +43,6 @@
 	mv64x60@f1000000 { /* Marvell Discovery */
 		#address-cells = <1>;
 		#size-cells = <1>;
-		#interrupt-cells = <1>;
 		model = "mv64360";			/* Default */
 		compatible = "marvell,mv64x60";
 		clock-frequency = <7f28155>;		/* 133.333333 MHz */

arch/powerpc/boot/dts/sequoia.dts

@@ -0,0 +1,302 @@
+/*
+ * Device Tree Source for AMCC Sequoia
+ *
+ * Based on Bamboo code by Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ * Copyright (c) 2006, 2007 IBM Corp.
+ *
+ * FIXME: Draft only!
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ */
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	model = "amcc,sequoia";
+	compatible = "amcc,sequoia";
+	dcr-parent = <&/cpus/PowerPC,440EPx@0>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,440EPx@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <0>; /* Filled in by zImage */
+			timebase-frequency = <0>; /* Filled in by zImage */
+			i-cache-line-size = <20>;
+			d-cache-line-size = <20>;
+			i-cache-size = <8000>;
+			d-cache-size = <8000>;
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0 0>; /* Filled in by zImage */
+	};
+
+	UIC0: interrupt-controller0 {
+		compatible = "ibm,uic-440epx","ibm,uic";
+		interrupt-controller;
+		cell-index = <0>;
+		dcr-reg = <0c0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+	};
+
+	UIC1: interrupt-controller1 {
+		compatible = "ibm,uic-440epx","ibm,uic";
+		interrupt-controller;
+		cell-index = <1>;
+		dcr-reg = <0d0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupt-parent = <&UIC0>;
+	};
+
+	UIC2: interrupt-controller2 {
+		compatible = "ibm,uic-440epx","ibm,uic";
+		interrupt-controller;
+		cell-index = <2>;
+		dcr-reg = <0e0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <1c 4 1d 4>; /* cascade */
+		interrupt-parent = <&UIC0>;
+	};
+
+	SDR0: sdr {
+		compatible = "ibm,sdr-440epx", "ibm,sdr-440ep";
+		dcr-reg = <00e 002>;
+	};
+
+	CPR0: cpr {
+		compatible = "ibm,cpr-440epx", "ibm,cpr-440ep";
+		dcr-reg = <00c 002>;
+	};
+
+	plb {
+		compatible = "ibm,plb-440epx", "ibm,plb4";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <0>; /* Filled in by zImage */
+
+		SDRAM0: sdram {
+			device_type = "memory-controller";
+			compatible = "ibm,sdram-440epx", "ibm,sdram-44x-ddr2denali";
+			dcr-reg = <010 2>;
+		};
+
+		DMA0: dma {
+			compatible = "ibm,dma-440epx", "ibm,dma-4xx";
+			dcr-reg = <100 027>;
+		};
+
+		MAL0: mcmal {
+			compatible = "ibm,mcmal-440epx", "ibm,mcmal2";
+			dcr-reg = <180 62>;
+			num-tx-chans = <2>;
+			num-rx-chans = <2>;
+			interrupt-parent = <&MAL0>;
+			interrupts = <0 1 2 3 4>;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+					/*RXEOB*/ 1 &UIC0 b 4
+					/*SERR*/  2 &UIC1 0 4
+					/*TXDE*/  3 &UIC1 1 4
+					/*RXDE*/  4 &UIC1 2 4>;
+			interrupt-map-mask = <ffffffff>;
+		};
+
+		POB0: opb {
+		  	compatible = "ibm,opb-440epx", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		  	ranges = <00000000 1 00000000 80000000
+			          80000000 1 80000000 80000000>;
+		  	interrupt-parent = <&UIC1>;
+		  	interrupts = <7 4>;
+		  	clock-frequency = <0>; /* Filled in by zImage */
+
+			EBC0: ebc {
+				compatible = "ibm,ebc-440epx", "ibm,ebc";
+				dcr-reg = <012 2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				clock-frequency = <0>; /* Filled in by zImage */
+				interrupts = <5 1>;
+				interrupt-parent = <&UIC1>;
+
+				nor_flash@0,0 {
+					compatible = "amd,s29gl256n", "cfi-flash";
+					bank-width = <2>;
+					reg = <0 000000 4000000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					partition@0 {
+						label = "Kernel";
+						reg = <0 180000>;
+					};
+					partition@180000 {
+						label = "ramdisk";
+						reg = <180000 200000>;
+					};
+					partition@380000 {
+						label = "file system";
+						reg = <380000 3aa0000>;
+					};
+					partition@3e20000 {
+						label = "kozio";
+						reg = <3e20000 140000>;
+					};
+					partition@3f60000 {
+						label = "env";
+						reg = <3f60000 40000>;
+					};
+					partition@3fa0000 {
+						label = "u-boot";
+						reg = <3fa0000 60000>;
+					};
+				};
+
+			};
+
+			UART0: serial@ef600300 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600300 8>;
+		   		virtual-reg = <ef600300>;
+		   		clock-frequency = <0>; /* Filled in by zImage */
+		   		current-speed = <1c200>;
+		   		interrupt-parent = <&UIC0>;
+		   		interrupts = <0 4>;
+	   		};
+
+			UART1: serial@ef600400 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600400 8>;
+		   		virtual-reg = <ef600400>;
+		   		clock-frequency = <0>;
+		   		current-speed = <0>;
+		   		interrupt-parent = <&UIC0>;
+		   		interrupts = <1 4>;
+	   		};
+
+			UART2: serial@ef600500 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600500 8>;
+		   		virtual-reg = <ef600500>;
+		   		clock-frequency = <0>;
+		   		current-speed = <0>;
+		   		interrupt-parent = <&UIC1>;
+		   		interrupts = <3 4>;
+	   		};
+
+			UART3: serial@ef600600 {
+		   		device_type = "serial";
+		   		compatible = "ns16550";
+		   		reg = <ef600600 8>;
+		   		virtual-reg = <ef600600>;
+		   		clock-frequency = <0>;
+		   		current-speed = <0>;
+		   		interrupt-parent = <&UIC1>;
+		   		interrupts = <4 4>;
+	   		};
+
+			IIC0: i2c@ef600700 {
+				device_type = "i2c";
+				compatible = "ibm,iic-440epx", "ibm,iic";
+				reg = <ef600700 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <2 4>;
+			};
+
+			IIC1: i2c@ef600800 {
+				device_type = "i2c";
+				compatible = "ibm,iic-440epx", "ibm,iic";
+				reg = <ef600800 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <7 4>;
+			};
+
+			ZMII0: emac-zmii@ef600d00 {
+				device_type = "zmii-interface";
+				compatible = "ibm,zmii-440epx", "ibm,zmii";
+				reg = <ef600d00 c>;
+			};
+
+			EMAC0: ethernet@ef600e00 {
+				linux,network-index = <0>;
+				device_type = "network";
+				compatible = "ibm,emac-440epx", "ibm,emac4";
+				interrupt-parent = <&EMAC0>;
+				interrupts = <0 1>;
+				#interrupt-cells = <1>;
+				#address-cells = <0>;
+				#size-cells = <0>;
+				interrupt-map = </*Status*/ 0 &UIC0 18 4
+						/*Wake*/  1 &UIC1 1d 4>;
+				reg = <ef600e00 70>;
+				local-mac-address = [000000000000];
+				mal-device = <&MAL0>;
+				mal-tx-channel = <0>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000000>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <0>;
+			};
+
+			EMAC1: ethernet@ef600f00 {
+				linux,network-index = <1>;
+				device_type = "network";
+				compatible = "ibm,emac-440epx", "ibm,emac4";
+				interrupt-parent = <&EMAC1>;
+				interrupts = <0 1>;
+				#interrupt-cells = <1>;
+				#address-cells = <0>;
+				#size-cells = <0>;
+				interrupt-map = </*Status*/ 0 &UIC0 19 4
+						/*Wake*/  1 &UIC1 1f 4>;
+				reg = <ef600f00 70>;
+				local-mac-address = [000000000000];
+				mal-device = <&MAL0>;
+				mal-tx-channel = <1>;
+				mal-rx-channel = <1>;
+				cell-index = <1>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000000>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <1>;
+			};
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@ef600300";
+		bootargs = "console=ttyS0,115200";
+	};
+};

arch/powerpc/boot/dts/walnut.dts

@@ -0,0 +1,190 @@
+/*
+ * Device Tree Source for IBM Walnut
+ *
+ * Copyright 2007 IBM Corp.
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "ibm,walnut";
+	compatible = "ibm,walnut";
+	dcr-parent = <&/cpus/PowerPC,405GP@0>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,405GP@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <bebc200>; /* Filled in by zImage */
+			timebase-frequency = <0>; /* Filled in by zImage */
+			i-cache-line-size = <20>;
+			d-cache-line-size = <20>;
+			i-cache-size = <4000>;
+			d-cache-size = <4000>;
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>; /* Filled in by zImage */
+	};
+
+	UIC0: interrupt-controller {
+		compatible = "ibm,uic";
+		interrupt-controller;
+		cell-index = <0>;
+		dcr-reg = <0c0 9>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+	};
+
+	plb {
+		compatible = "ibm,plb3";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <0>; /* Filled in by zImage */
+
+		SDRAM0: memory-controller {
+			compatible = "ibm,sdram-405gp";
+			dcr-reg = <010 2>;
+		};
+
+		MAL: mcmal {
+			compatible = "ibm,mcmal-405gp", "ibm,mcmal";
+			dcr-reg = <180 62>;
+			num-tx-chans = <2>;
+			num-rx-chans = <1>;
+			interrupt-parent = <&UIC0>;
+			interrupts = <a 4 b 4 c 4 d 4 e 4>;
+		};
+
+		POB0: opb {
+			compatible = "ibm,opb-405gp", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <ef600000 ef600000 a00000>;
+			dcr-reg = <0a0 5>;
+			clock-frequency = <0>; /* Filled in by zImage */
+
+			UART0: serial@ef600300 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <ef600300 8>;
+				virtual-reg = <ef600300>;
+				clock-frequency = <0>; /* Filled in by zImage */
+				current-speed = <2580>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0 4>;
+			};
+
+			UART1: serial@ef600400 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <ef600400 8>;
+				virtual-reg = <ef600400>;
+				clock-frequency = <0>; /* Filled in by zImage */
+				current-speed = <2580>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <1 4>;
+			};
+
+			IIC: i2c@ef600500 {
+				compatible = "ibm,iic-405gp", "ibm,iic";
+				reg = <ef600500 11>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <2 4>;
+			};
+
+			GPIO: gpio@ef600700 {
+				compatible = "ibm,gpio-405gp";
+				reg = <ef600700 20>;
+			};
+
+			EMAC: ethernet@ef600800 {
+				linux,network-index = <0>;
+				device_type = "network";
+				compatible = "ibm,emac-405gp", "ibm,emac";
+				interrupt-parent = <&UIC0>;
+				interrupts = <9 4 f 4>;
+				reg = <ef600800 70>;
+				mal-device = <&MAL>;
+				mal-tx-channel = <0 1>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+			};
+
+		};
+
+		EBC0: ebc {
+			compatible = "ibm,ebc-405gp", "ibm,ebc";
+			dcr-reg = <012 2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			/* The ranges property is supplied by the bootwrapper
+			 * and is based on the firmware's configuration of the
+			 * EBC bridge
+			 */
+			clock-frequency = <0>; /* Filled in by zImage */
+
+			sram@0,0 {
+				reg = <0 0 80000>;
+			};
+
+			flash@0,80000 {
+				compatible = "jedec-flash";
+				bank-width = <1>;
+				reg = <0 80000 80000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				partition@0 {
+					label = "OpenBIOS";
+					reg = <0 80000>;
+					read-only;
+				};
+			};
+
+			ds1743@1,0 {
+				/* NVRAM and RTC */
+				compatible = "ds1743";
+				reg = <1 0 2000>;
+			};
+
+			keyboard@2,0 {
+				compatible = "intel,82C42PC";
+				reg = <2 0 2>;
+			};
+
+			ir@3,0 {
+				compatible = "ti,TIR2000PAG";
+				reg = <3 0 10>;
+			};
+
+			fpga@7,0 {
+				compatible = "Walnut-FPGA";
+				reg = <7 0 10>;
+				virtual-reg = <f0300005>;
+			};
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@ef600300";
+	};
+};

arch/powerpc/boot/ebony.c

@@ -24,12 +24,11 @@
 #include "page.h"
 #include "ops.h"
 #include "reg.h"
+#include "io.h"
 #include "dcr.h"
+#include "4xx.h"
 #include "44x.h"
 
-extern char _dtb_start[];
-extern char _dtb_end[];
-
 static u8 *ebony_mac0, *ebony_mac1;
 
 /* Calculate 440GP clocks */
@@ -92,15 +91,53 @@ void ibm440gp_fixup_clocks(unsigned int sysclk, unsigned int ser_clk)
 	dt_fixup_clock("/plb/opb/serial@40000300", uart1);
 }
 
+#define EBONY_FPGA_PATH		"/plb/opb/ebc/fpga"
+#define	EBONY_FPGA_FLASH_SEL	0x01
+#define EBONY_SMALL_FLASH_PATH	"/plb/opb/ebc/small-flash"
+
+static void ebony_flashsel_fixup(void)
+{
+	void *devp;
+	u32 reg[3] = {0x0, 0x0, 0x80000};
+	u8 *fpga;
+	u8 fpga_reg0 = 0x0;
+
+	devp = finddevice(EBONY_FPGA_PATH);
+	if (!devp)
+		fatal("Couldn't locate FPGA node %s\n\r", EBONY_FPGA_PATH);
+
+	if (getprop(devp, "virtual-reg", &fpga, sizeof(fpga)) != sizeof(fpga))
+		fatal("%s has missing or invalid virtual-reg property\n\r",
+		      EBONY_FPGA_PATH);
+
+	fpga_reg0 = in_8(fpga);
+
+	devp = finddevice(EBONY_SMALL_FLASH_PATH);
+	if (!devp)
+		fatal("Couldn't locate small flash node %s\n\r",
+		      EBONY_SMALL_FLASH_PATH);
+
+	if (getprop(devp, "reg", reg, sizeof(reg)) != sizeof(reg))
+		fatal("%s has reg property of unexpected size\n\r",
+		      EBONY_SMALL_FLASH_PATH);
+
+	/* Invert address bit 14 (IBM-endian) if FLASH_SEL fpga bit is set */
+	if (fpga_reg0 & EBONY_FPGA_FLASH_SEL)
+		reg[1] ^= 0x80000;
+
+	setprop(devp, "reg", reg, sizeof(reg));
+}
+
 static void ebony_fixups(void)
 {
 	// FIXME: sysclk should be derived by reading the FPGA registers
 	unsigned long sysclk = 33000000;
 
 	ibm440gp_fixup_clocks(sysclk, 6 * 1843200);
-	ibm44x_fixup_memsize();
+	ibm4xx_fixup_memsize();
 	dt_fixup_mac_addresses(ebony_mac0, ebony_mac1);
 	ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
+	ebony_flashsel_fixup();
 }
 
 void ebony_init(void *mac0, void *mac1)

arch/powerpc/boot/ep88xc.c

@@ -0,0 +1,54 @@
+/*
+ * Embedded Planet EP88xC with PlanetCore firmware
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "planetcore.h"
+#include "mpc8xx.h"
+
+static char *table;
+static u64 mem_size;
+
+static void platform_fixups(void)
+{
+	u64 val;
+
+	dt_fixup_memory(0, mem_size);
+	planetcore_set_mac_addrs(table);
+
+	if (!planetcore_get_decimal(table, PLANETCORE_KEY_CRYSTAL_HZ, &val)) {
+		printf("No PlanetCore crystal frequency key.\r\n");
+		return;
+	}
+
+	mpc885_fixup_clocks(val);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+                   unsigned long r6, unsigned long r7)
+{
+	table = (char *)r3;
+	planetcore_prepare_table(table);
+
+	if (!planetcore_get_decimal(table, PLANETCORE_KEY_MB_RAM, &mem_size))
+		return;
+
+	mem_size *= 1024 * 1024;
+	simple_alloc_init(_end, mem_size - (unsigned long)_end, 32, 64);
+
+	ft_init(_dtb_start, _dtb_end - _dtb_start, 32);
+
+	planetcore_set_stdout_path(table);
+
+	serial_console_init();
+	platform_ops.fixups = platform_fixups;
+}

arch/powerpc/boot/fixed-head.S

@@ -0,0 +1,4 @@
+	.text
+	.global _zimage_start
+_zimage_start:
+	b	_zimage_start_lib

arch/powerpc/boot/flatdevtree.c

@@ -354,16 +354,21 @@ static void ft_put_bin(struct ft_cxt *cxt, const void *data, unsigned int sz)
 	cxt->p += sza;
 }
 
-int ft_begin_node(struct ft_cxt *cxt, const char *name)
+char *ft_begin_node(struct ft_cxt *cxt, const char *name)
 {
 	unsigned long nlen = strlen(name) + 1;
 	unsigned long len = 8 + _ALIGN(nlen, 4);
+	char *ret;
 
 	if (!ft_make_space(cxt, &cxt->p, FT_STRUCT, len))
-		return -1;
+		return NULL;
+
+	ret = cxt->p;
+
 	ft_put_word(cxt, OF_DT_BEGIN_NODE);
 	ft_put_bin(cxt, name, strlen(name) + 1);
-	return 0;
+
+	return ret;
 }
 
 void ft_end_node(struct ft_cxt *cxt)
@@ -625,25 +630,17 @@ void ft_end_tree(struct ft_cxt *cxt)
 	bph->dt_strings_size = cpu_to_be32(ssize);
 }
 
-void *ft_find_device(struct ft_cxt *cxt, const char *srch_path)
-{
-	char *node;
-
-	/* require absolute path */
-	if (srch_path[0] != '/')
-		return NULL;
-	node = ft_find_descendent(cxt, ft_root_node(cxt), srch_path);
-	return ft_get_phandle(cxt, node);
-}
-
-void *ft_find_device_rel(struct ft_cxt *cxt, const void *top,
-                         const char *srch_path)
+void *ft_find_device(struct ft_cxt *cxt, const void *top, const char *srch_path)
 {
 	char *node;
 
-	node = ft_node_ph2node(cxt, top);
-	if (node == NULL)
-		return NULL;
+	if (top) {
+		node = ft_node_ph2node(cxt, top);
+		if (node == NULL)
+			return NULL;
+	} else {
+		node = ft_root_node(cxt);
+	}
 
 	node = ft_find_descendent(cxt, node, srch_path);
 	return ft_get_phandle(cxt, node);
@@ -945,7 +942,7 @@ int ft_del_prop(struct ft_cxt *cxt, const void *phandle, const char *propname)
 void *ft_create_node(struct ft_cxt *cxt, const void *parent, const char *name)
 {
 	struct ft_atom atom;
-	char *p, *next;
+	char *p, *next, *ret;
 	int depth = 0;
 
 	if (parent) {
@@ -970,11 +967,70 @@ void *ft_create_node(struct ft_cxt *cxt, const void *parent, const char *name)
 				break;
 			/* end of node, insert here */
 			cxt->p = p;
-			ft_begin_node(cxt, name);
+			ret = ft_begin_node(cxt, name);
 			ft_end_node(cxt);
-			return p;
+			return ft_get_phandle(cxt, ret);
 		}
 		p = next;
 	}
 	return NULL;
 }
+
+/* Returns the start of the path within the provided buffer, or NULL on
+ * error.
+ */
+char *ft_get_path(struct ft_cxt *cxt, const void *phandle,
+                  char *buf, int len)
+{
+	const char *path_comp[FT_MAX_DEPTH];
+	struct ft_atom atom;
+	char *p, *next, *pos;
+	int depth = 0, i;
+	void *node;
+
+	node = ft_node_ph2node(cxt, phandle);
+	if (node == NULL)
+		return NULL;
+
+	p = ft_root_node(cxt);
+
+	while ((next = ft_next(cxt, p, &atom)) != NULL) {
+		switch (atom.tag) {
+		case OF_DT_BEGIN_NODE:
+			path_comp[depth++] = atom.name;
+			if (p == node)
+				goto found;
+
+			break;
+
+		case OF_DT_END_NODE:
+			if (--depth == 0)
+				return NULL;
+		}
+
+		p = next;
+	}
+
+found:
+	pos = buf;
+	for (i = 1; i < depth; i++) {
+		int this_len;
+
+		if (len <= 1)
+			return NULL;
+
+		*pos++ = '/';
+		len--;
+
+		strncpy(pos, path_comp[i], len);
+
+		if (pos[len - 1] != 0)
+			return NULL;
+
+		this_len = strlen(pos);
+		len -= this_len;
+		pos += this_len;
+	}
+
+	return buf;
+}

arch/powerpc/boot/flatdevtree.h

@@ -76,7 +76,7 @@ struct ft_cxt {
 	unsigned int nodes_used;
 };
 
-int ft_begin_node(struct ft_cxt *cxt, const char *name);
+char *ft_begin_node(struct ft_cxt *cxt, const char *name);
 void ft_end_node(struct ft_cxt *cxt);
 
 void ft_begin_tree(struct ft_cxt *cxt);
@@ -96,9 +96,8 @@ int ft_add_rsvmap(struct ft_cxt *cxt, u64 physaddr, u64 size);
 
 void ft_dump_blob(const void *bphp);
 void ft_merge_blob(struct ft_cxt *cxt, void *blob);
-void *ft_find_device(struct ft_cxt *cxt, const char *srch_path);
-void *ft_find_device_rel(struct ft_cxt *cxt, const void *top,
-                         const char *srch_path);
+void *ft_find_device(struct ft_cxt *cxt, const void *top,
+                     const char *srch_path);
 void *ft_find_descendent(struct ft_cxt *cxt, void *top, const char *srch_path);
 int ft_get_prop(struct ft_cxt *cxt, const void *phandle, const char *propname,
 		void *buf, const unsigned int buflen);
@@ -109,5 +108,6 @@ void *ft_find_node_by_prop_value(struct ft_cxt *cxt, const void *prev,
                                  const char *propname, const char *propval,
                                  int proplen);
 void *ft_create_node(struct ft_cxt *cxt, const void *parent, const char *name);
+char *ft_get_path(struct ft_cxt *cxt, const void *phandle, char *buf, int len);
 
 #endif /* FLATDEVTREE_H */

arch/powerpc/boot/flatdevtree_env.h

@@ -24,24 +24,4 @@
 #define be64_to_cpu(x)		(x)
 #define cpu_to_be64(x)		(x)
 
-static inline int strncmp(const char *cs, const char *ct, size_t count)
-{
-	signed char __res = 0;
-
-	while (count) {
-		if ((__res = *cs - *ct++) != 0 || !*cs++)
-			break;
-		count--;
-	}
-	return __res;
-}
-
-static inline char *strchr(const char *s, int c)
-{
-	for (; *s != (char)c; ++s)
-		if (*s == '\0')
-			return NULL;
-	return (char *)s;
-}
-
 #endif /* _PPC_BOOT_FLATDEVTREE_ENV_H_ */

arch/powerpc/boot/flatdevtree_misc.c

@@ -18,7 +18,7 @@ static struct ft_cxt cxt;
 
 static void *fdtm_finddevice(const char *name)
 {
-	return ft_find_device(&cxt, name);
+	return ft_find_device(&cxt, NULL, name);
 }
 
 static int fdtm_getprop(const void *phandle, const char *propname,
@@ -58,6 +58,11 @@ static unsigned long fdtm_finalize(void)
 	return (unsigned long)cxt.bph;
 }
 
+static char *fdtm_get_path(const void *phandle, char *buf, int len)
+{
+	return ft_get_path(&cxt, phandle, buf, len);
+}
+
 int ft_init(void *dt_blob, unsigned int max_size, unsigned int max_find_device)
 {
 	dt_ops.finddevice = fdtm_finddevice;
@@ -67,6 +72,7 @@ int ft_init(void *dt_blob, unsigned int max_size, unsigned int max_find_device)
 	dt_ops.create_node = fdtm_create_node;
 	dt_ops.find_node_by_prop_value = fdtm_find_node_by_prop_value;
 	dt_ops.finalize = fdtm_finalize;
+	dt_ops.get_path = fdtm_get_path;
 
 	return ft_open(&cxt, dt_blob, max_size, max_find_device,
 			platform_ops.realloc);

arch/powerpc/boot/fsl-soc.c

@@ -0,0 +1,57 @@
+/*
+ * Freescale SOC support functions
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "types.h"
+#include "fsl-soc.h"
+#include "stdio.h"
+
+static u32 prop_buf[MAX_PROP_LEN / 4];
+
+u32 *fsl_get_immr(void)
+{
+	void *soc;
+	unsigned long ret = 0;
+
+	soc = find_node_by_devtype(NULL, "soc");
+	if (soc) {
+		int size;
+		u32 naddr;
+
+		size = getprop(soc, "#address-cells", prop_buf, MAX_PROP_LEN);
+		if (size == 4)
+			naddr = prop_buf[0];
+		else
+			naddr = 2;
+
+		if (naddr != 1 && naddr != 2)
+			goto err;
+
+		size = getprop(soc, "ranges", prop_buf, MAX_PROP_LEN);
+
+		if (size < 12)
+			goto err;
+		if (prop_buf[0] != 0)
+			goto err;
+		if (naddr == 2 && prop_buf[1] != 0)
+			goto err;
+
+		if (!dt_xlate_addr(soc, prop_buf + naddr, 8, &ret))
+			ret = 0;
+	}
+
+err:
+	if (!ret)
+		printf("fsl_get_immr: Failed to find immr base\r\n");
+
+	return (u32 *)ret;
+}

arch/powerpc/boot/fsl-soc.h

@@ -0,0 +1,8 @@
+#ifndef _PPC_BOOT_FSL_SOC_H_
+#define _PPC_BOOT_FSL_SOC_H_
+
+#include "types.h"
+
+u32 *fsl_get_immr(void);
+
+#endif

arch/powerpc/boot/gunzip_util.c

@@ -78,6 +78,7 @@ void gunzip_start(struct gunzip_state *state, void *src, int srclen)
 			fatal("inflateInit2 returned %d\n\r", r);
 	}
 
+	state->s.total_in = hdrlen;
 	state->s.next_in = src + hdrlen;
 	state->s.avail_in = srclen - hdrlen;
 }
@@ -193,13 +194,10 @@ int gunzip_finish(struct gunzip_state *state, void *dst, int dstlen)
 {
 	int len;
 
+	len = gunzip_partial(state, dst, dstlen);
+
 	if (state->s.workspace) {
-		len = gunzip_partial(state, dst, dstlen);
 		zlib_inflateEnd(&state->s);
-	} else {
-		/* uncompressed image */
-		len = min(state->s.avail_in, (unsigned)dstlen);
-		memcpy(dst, state->s.next_in, len);
 	}
 
 	return len;

arch/powerpc/boot/holly.c

@@ -21,11 +21,6 @@
 #include "ops.h"
 #include "io.h"
 
-extern char _start[];
-extern char _end[];
-extern char _dtb_start[];
-extern char _dtb_end[];
-
 BSS_STACK(4096);
 
 void platform_init(unsigned long r3, unsigned long r4, unsigned long r5)

arch/powerpc/boot/io.h

@@ -1,5 +1,8 @@
 #ifndef _IO_H
 #define __IO_H
+
+#include "types.h"
+
 /*
  * Low-level I/O routines.
  *
@@ -20,6 +23,37 @@ static inline void out_8(volatile unsigned char *addr, int val)
 			     : "=m" (*addr) : "r" (val));
 }
 
+static inline unsigned in_le16(const volatile u16 *addr)
+{
+	unsigned ret;
+
+	__asm__ __volatile__("lhbrx %0,0,%1; twi 0,%0,0; isync"
+			     : "=r" (ret) : "r" (addr), "m" (*addr));
+
+	return ret;
+}
+
+static inline unsigned in_be16(const volatile u16 *addr)
+{
+	unsigned ret;
+
+	__asm__ __volatile__("lhz%U1%X1 %0,%1; twi 0,%0,0; isync"
+			     : "=r" (ret) : "m" (*addr));
+	return ret;
+}
+
+static inline void out_le16(volatile u16 *addr, int val)
+{
+	__asm__ __volatile__("sthbrx %1,0,%2; sync" : "=m" (*addr)
+			     : "r" (val), "r" (addr));
+}
+
+static inline void out_be16(volatile u16 *addr, int val)
+{
+	__asm__ __volatile__("sth%U0%X0 %1,%0; sync"
+			     : "=m" (*addr) : "r" (val));
+}
+
 static inline unsigned in_le32(const volatile unsigned *addr)
 {
 	unsigned ret;
@@ -50,4 +84,19 @@ static inline void out_be32(volatile unsigned *addr, int val)
 			     : "=m" (*addr) : "r" (val));
 }
 
+static inline void sync(void)
+{
+	asm volatile("sync" : : : "memory");
+}
+
+static inline void eieio(void)
+{
+	asm volatile("eieio" : : : "memory");
+}
+
+static inline void barrier(void)
+{
+	asm volatile("" : : : "memory");
+}
+
 #endif /* _IO_H */

arch/powerpc/boot/main.c

@@ -19,16 +19,6 @@
 #include "flatdevtree.h"
 #include "reg.h"
 
-extern char _start[];
-extern char __bss_start[];
-extern char _end[];
-extern char _vmlinux_start[];
-extern char _vmlinux_end[];
-extern char _initrd_start[];
-extern char _initrd_end[];
-extern char _dtb_start[];
-extern char _dtb_end[];
-
 static struct gunzip_state gzstate;
 
 struct addr_range {

arch/powerpc/boot/mpc52xx-psc.c

@@ -0,0 +1,69 @@
+/*
+ * MPC5200 PSC serial console support.
+ *
+ * Author: Grant Likely <grant.likely@secretlab.ca>
+ *
+ * Copyright (c) 2007 Secret Lab Technologies Ltd.
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * It is assumed that the firmware (or the platform file) has already set
+ * up the port.
+ */
+
+#include "types.h"
+#include "io.h"
+#include "ops.h"
+
+/* Programmable Serial Controller (PSC) status register bits */
+#define MPC52xx_PSC_SR		0x04
+#define MPC52xx_PSC_SR_RXRDY		0x0100
+#define MPC52xx_PSC_SR_RXFULL		0x0200
+#define MPC52xx_PSC_SR_TXRDY		0x0400
+#define MPC52xx_PSC_SR_TXEMP		0x0800
+
+#define MPC52xx_PSC_BUFFER	0x0C
+
+static void *psc;
+
+static int psc_open(void)
+{
+	/* Assume the firmware has already configured the PSC into
+	 * uart mode */
+	return 0;
+}
+
+static void psc_putc(unsigned char c)
+{
+	while (!(in_be16(psc + MPC52xx_PSC_SR) & MPC52xx_PSC_SR_TXRDY)) ;
+	out_8(psc + MPC52xx_PSC_BUFFER, c);
+}
+
+static unsigned char psc_tstc(void)
+{
+	return (in_be16(psc + MPC52xx_PSC_SR) & MPC52xx_PSC_SR_RXRDY) != 0;
+}
+
+static unsigned char psc_getc(void)
+{
+	while (!(in_be16(psc + MPC52xx_PSC_SR) & MPC52xx_PSC_SR_RXRDY)) ;
+	return in_8(psc + MPC52xx_PSC_BUFFER);
+}
+
+int mpc5200_psc_console_init(void *devp, struct serial_console_data *scdp)
+{
+	int n;
+
+	/* Get the base address of the psc registers */
+	n = getprop(devp, "virtual-reg", &psc, sizeof(psc));
+	if (n != sizeof(psc)) {
+		if (!dt_xlate_reg(devp, 0, (void *)&psc, NULL))
+			return -1;
+	}
+
+	scdp->open = psc_open;
+	scdp->putc = psc_putc;
+	scdp->getc = psc_getc;
+	scdp->tstc = psc_tstc;
+
+	return 0;
+}

arch/powerpc/boot/mpc8xx.c

@@ -0,0 +1,82 @@
+/*
+ * MPC8xx support functions
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "types.h"
+#include "fsl-soc.h"
+#include "mpc8xx.h"
+#include "stdio.h"
+#include "io.h"
+
+#define MPC8XX_PLPRCR (0x284/4) /* PLL and Reset Control Register */
+
+/* Return system clock from crystal frequency */
+u32 mpc885_get_clock(u32 crystal)
+{
+	u32 *immr;
+	u32 plprcr;
+	int mfi, mfn, mfd, pdf, div;
+	u32 ret;
+
+	immr = fsl_get_immr();
+	if (!immr) {
+		printf("mpc885_get_clock: Couldn't get IMMR base.\r\n");
+		return 0;
+	}
+
+	plprcr = in_be32(&immr[MPC8XX_PLPRCR]);
+
+	mfi = (plprcr >> 16) & 15;
+	if (mfi < 5) {
+		printf("Warning: PLPRCR[MFI] value of %d out-of-bounds\r\n",
+		       mfi);
+		mfi = 5;
+	}
+
+	pdf = (plprcr >> 1) & 0xf;
+	div = (plprcr >> 20) & 3;
+	mfd = (plprcr >> 22) & 0x1f;
+	mfn = (plprcr >> 27) & 0x1f;
+
+	ret = crystal * mfi;
+
+	if (mfn != 0)
+		ret += crystal * mfn / (mfd + 1);
+
+	return ret / (pdf + 1);
+}
+
+/* Set common device tree fields based on the given clock frequencies. */
+void mpc8xx_set_clocks(u32 sysclk)
+{
+	void *node;
+
+	dt_fixup_cpu_clocks(sysclk, sysclk / 16, sysclk);
+
+	node = finddevice("/soc/cpm");
+	if (node)
+		setprop(node, "clock-frequency", &sysclk, 4);
+
+	node = finddevice("/soc/cpm/brg");
+	if (node)
+		setprop(node, "clock-frequency", &sysclk, 4);
+}
+
+int mpc885_fixup_clocks(u32 crystal)
+{
+	u32 sysclk = mpc885_get_clock(crystal);
+	if (!sysclk)
+		return 0;
+
+	mpc8xx_set_clocks(sysclk);
+	return 1;
+}

arch/powerpc/boot/mpc8xx.h

@@ -0,0 +1,11 @@
+#ifndef _PPC_BOOT_MPC8xx_H_
+#define _PPC_BOOT_MPC8xx_H_
+
+#include "types.h"
+
+void mpc8xx_set_clocks(u32 sysclk);
+
+u32 mpc885_get_clock(u32 crystal);
+int mpc885_fixup_clocks(u32 crystal);
+
+#endif

arch/powerpc/boot/mpsc.c

@@ -17,7 +17,6 @@
 #include "io.h"
 #include "ops.h"
 
-extern void udelay(long delay);
 
 #define MPSC_CHR_1		0x000c
 

arch/powerpc/boot/mv64x60_i2c.c

@@ -21,8 +21,6 @@
 #include "ops.h"
 #include "mv64x60.h"
 
-extern void udelay(long);
-
 /* Register defines */
 #define MV64x60_I2C_REG_SLAVE_ADDR			0x00
 #define MV64x60_I2C_REG_DATA				0x04

arch/powerpc/boot/of.c

@@ -17,8 +17,6 @@
 
 #include "of.h"
 
-extern char _end[];
-
 /* Value picked to match that used by yaboot */
 #define PROG_START	0x01400000	/* only used on 64-bit systems */
 #define RAM_END		(512<<20)	/* Fixme: use OF */

arch/powerpc/boot/ops.h

@@ -47,6 +47,7 @@ struct dt_ops {
 	                                 const char *propname,
 	                                 const char *propval, int proplen);
 	unsigned long (*finalize)(void);
+	char *(*get_path)(const void *phandle, char *buf, int len);
 };
 extern struct dt_ops dt_ops;
 
@@ -82,11 +83,16 @@ int ft_init(void *dt_blob, unsigned int max_size, unsigned int max_find_device);
 int serial_console_init(void);
 int ns16550_console_init(void *devp, struct serial_console_data *scdp);
 int mpsc_console_init(void *devp, struct serial_console_data *scdp);
+int cpm_console_init(void *devp, struct serial_console_data *scdp);
+int mpc5200_psc_console_init(void *devp, struct serial_console_data *scdp);
+int uartlite_console_init(void *devp, struct serial_console_data *scdp);
 void *simple_alloc_init(char *base, unsigned long heap_size,
 			unsigned long granularity, unsigned long max_allocs);
 extern void flush_cache(void *, unsigned long);
 int dt_xlate_reg(void *node, int res, unsigned long *addr, unsigned long *size);
 int dt_xlate_addr(void *node, u32 *buf, int buflen, unsigned long *xlated_addr);
+int dt_is_compatible(void *node, const char *compat);
+void dt_get_reg_format(void *node, u32 *naddr, u32 *nsize);
 
 static inline void *finddevice(const char *name)
 {
@@ -156,6 +162,7 @@ static inline void *find_node_by_devtype(const void *prev,
 void dt_fixup_memory(u64 start, u64 size);
 void dt_fixup_cpu_clocks(u32 cpufreq, u32 tbfreq, u32 busfreq);
 void dt_fixup_clock(const char *path, u32 freq);
+void dt_fixup_mac_address(u32 index, const u8 *addr);
 void __dt_fixup_mac_addresses(u32 startindex, ...);
 #define dt_fixup_mac_addresses(...) \
 	__dt_fixup_mac_addresses(0, __VA_ARGS__, NULL)
@@ -167,6 +174,14 @@ static inline void *find_node_by_linuxphandle(const u32 linuxphandle)
 			(char *)&linuxphandle, sizeof(u32));
 }
 
+static inline char *get_path(const void *phandle, char *buf, int len)
+{
+	if (dt_ops.get_path)
+		return dt_ops.get_path(phandle, buf, len);
+
+	return NULL;
+}
+
 static inline void *malloc(unsigned long size)
 {
 	return (platform_ops.malloc) ? platform_ops.malloc(size) : NULL;
@@ -191,4 +206,25 @@ static inline void exit(void)
 	static char _bss_stack[size]; \
 	void *_platform_stack_top = _bss_stack + sizeof(_bss_stack);
 
+extern unsigned long timebase_period_ns;
+void udelay(long delay);
+
+extern char _start[];
+extern char __bss_start[];
+extern char _end[];
+extern char _vmlinux_start[];
+extern char _vmlinux_end[];
+extern char _initrd_start[];
+extern char _initrd_end[];
+extern char _dtb_start[];
+extern char _dtb_end[];
+
+static inline __attribute__((const))
+int __ilog2_u32(u32 n)
+{
+	int bit;
+	asm ("cntlzw %0,%1" : "=r" (bit) : "r" (n));
+	return 31 - bit;
+}
+
 #endif /* _PPC_BOOT_OPS_H_ */

arch/powerpc/boot/planetcore.c

@@ -0,0 +1,166 @@
+/*
+ * PlanetCore configuration data support functions
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "stdio.h"
+#include "stdlib.h"
+#include "ops.h"
+#include "planetcore.h"
+#include "io.h"
+
+/* PlanetCore passes information to the OS in the form of
+ * a table of key=value strings, separated by newlines.
+ *
+ * The list is terminated by an empty string (i.e. two
+ * consecutive newlines).
+ *
+ * To make it easier to parse, we first convert all the
+ * newlines into null bytes.
+ */
+
+void planetcore_prepare_table(char *table)
+{
+	do {
+		if (*table == '\n')
+			*table = 0;
+
+		table++;
+	} while (*(table - 1) || *table != '\n');
+
+	*table = 0;
+}
+
+const char *planetcore_get_key(const char *table, const char *key)
+{
+	int keylen = strlen(key);
+
+	do {
+		if (!strncmp(table, key, keylen) && table[keylen] == '=')
+			return table + keylen + 1;
+
+		table += strlen(table) + 1;
+	} while (strlen(table) != 0);
+
+	return NULL;
+}
+
+int planetcore_get_decimal(const char *table, const char *key, u64 *val)
+{
+	const char *str = planetcore_get_key(table, key);
+	if (!str)
+		return 0;
+
+	*val = strtoull(str, NULL, 10);
+	return 1;
+}
+
+int planetcore_get_hex(const char *table, const char *key, u64 *val)
+{
+	const char *str = planetcore_get_key(table, key);
+	if (!str)
+		return 0;
+
+	*val = strtoull(str, NULL, 16);
+	return 1;
+}
+
+static u64 mac_table[4] = {
+	0x000000000000,
+	0x000000800000,
+	0x000000400000,
+	0x000000c00000,
+};
+
+void planetcore_set_mac_addrs(const char *table)
+{
+	u8 addr[4][6];
+	u64 int_addr;
+	u32 i;
+	int j;
+
+	if (!planetcore_get_hex(table, PLANETCORE_KEY_MAC_ADDR, &int_addr))
+		return;
+
+	for (i = 0; i < 4; i++) {
+		u64 this_dev_addr = (int_addr & ~0x000000c00000) |
+		                    mac_table[i];
+
+		for (j = 5; j >= 0; j--) {
+			addr[i][j] = this_dev_addr & 0xff;
+			this_dev_addr >>= 8;
+		}
+
+		dt_fixup_mac_address(i, addr[i]);
+	}
+}
+
+static char prop_buf[MAX_PROP_LEN];
+
+void planetcore_set_stdout_path(const char *table)
+{
+	char *path;
+	const char *label;
+	void *node, *chosen;
+
+	label = planetcore_get_key(table, PLANETCORE_KEY_SERIAL_PORT);
+	if (!label)
+		return;
+
+	node = find_node_by_prop_value_str(NULL, "linux,planetcore-label",
+	                                   label);
+	if (!node)
+		return;
+
+	path = get_path(node, prop_buf, MAX_PROP_LEN);
+	if (!path)
+		return;
+
+	chosen = finddevice("/chosen");
+	if (!chosen)
+		chosen = create_node(NULL, "chosen");
+	if (!chosen)
+		return;
+
+	setprop_str(chosen, "linux,stdout-path", path);
+}
+
+void planetcore_set_serial_speed(const char *table)
+{
+	void *chosen, *stdout;
+	u64 baud;
+	u32 baud32;
+	int len;
+
+	chosen = finddevice("/chosen");
+	if (!chosen)
+		return;
+
+	len = getprop(chosen, "linux,stdout-path", prop_buf, MAX_PROP_LEN);
+	if (len <= 0)
+		return;
+
+	stdout = finddevice(prop_buf);
+	if (!stdout) {
+		printf("planetcore_set_serial_speed: "
+		       "Bad /chosen/linux,stdout-path.\r\n");
+
+		return;
+	}
+
+	if (!planetcore_get_decimal(table, PLANETCORE_KEY_SERIAL_BAUD,
+	                            &baud)) {
+		printf("planetcore_set_serial_speed: No SB tag.\r\n");
+		return;
+	}
+
+	baud32 = baud;
+	setprop(stdout, "current-speed", &baud32, 4);
+}

arch/powerpc/boot/planetcore.h

@@ -0,0 +1,49 @@
+#ifndef _PPC_BOOT_PLANETCORE_H_
+#define _PPC_BOOT_PLANETCORE_H_
+
+#include "types.h"
+
+#define PLANETCORE_KEY_BOARD_TYPE   "BO"
+#define PLANETCORE_KEY_BOARD_REV    "BR"
+#define PLANETCORE_KEY_MB_RAM       "D1"
+#define PLANETCORE_KEY_MAC_ADDR     "EA"
+#define PLANETCORE_KEY_FLASH_SPEED  "FS"
+#define PLANETCORE_KEY_IP_ADDR      "IP"
+#define PLANETCORE_KEY_KB_NVRAM     "NV"
+#define PLANETCORE_KEY_PROCESSOR    "PR"
+#define PLANETCORE_KEY_PROC_VARIANT "PV"
+#define PLANETCORE_KEY_SERIAL_BAUD  "SB"
+#define PLANETCORE_KEY_SERIAL_PORT  "SP"
+#define PLANETCORE_KEY_SWITCH       "SW"
+#define PLANETCORE_KEY_TEMP_OFFSET  "TC"
+#define PLANETCORE_KEY_TARGET_IP    "TIP"
+#define PLANETCORE_KEY_CRYSTAL_HZ   "XT"
+
+/* Prepare the table for processing, by turning all newlines
+ * into NULL bytes.
+ */
+void planetcore_prepare_table(char *table);
+
+/* Return the value associated with a given key in text,
+ * decimal, or hex format.
+ *
+ * Returns zero/NULL on failure, non-zero on success.
+ */
+const char *planetcore_get_key(const char *table, const char *key);
+int planetcore_get_decimal(const char *table, const char *key, u64 *val);
+int planetcore_get_hex(const char *table, const char *key, u64 *val);
+
+/* Updates the device tree local-mac-address properties based
+ * on the EA tag.
+ */
+void planetcore_set_mac_addrs(const char *table);
+
+/* Sets the linux,stdout-path in the /chosen node.  This requires the
+ * linux,planetcore-label property in each serial node.
+ */
+void planetcore_set_stdout_path(const char *table);
+
+/* Sets the current-speed property in the serial node. */
+void planetcore_set_serial_speed(const char *table);
+
+#endif

arch/powerpc/boot/ppcboot.h

@@ -78,17 +78,18 @@ typedef struct bd_info {
 	hymod_conf_t	bi_hymod_conf;	/* hymod configuration information */
 #endif
 #if defined(TARGET_EVB64260) || defined(TARGET_405EP) || defined(TARGET_44x) || \
-	defined(TARGET_85xx) ||	defined(TARGET_83xx)
+	defined(TARGET_85xx) ||	defined(TARGET_83xx) || defined(TARGET_HAS_ETH1)
 	/* second onboard ethernet port */
 	unsigned char	bi_enet1addr[6];
 #define HAVE_ENET1ADDR
 #endif
-#if defined(TARGET_EVB64260) || defined(TARGET_440GX) || defined(TARGET_85xx)
+#if defined(TARGET_EVB64260) || defined(TARGET_440GX) || \
+    defined(TARGET_85xx) || defined(TARGET_HAS_ETH2)
 	/* third onboard ethernet ports */
 	unsigned char	bi_enet2addr[6];
 #define HAVE_ENET2ADDR
 #endif
-#if defined(TARGET_440GX)
+#if defined(TARGET_440GX) || defined(TARGET_HAS_ETH3)
 	/* fourth onboard ethernet ports */
 	unsigned char	bi_enet3addr[6];
 #define HAVE_ENET3ADDR

arch/powerpc/boot/pq2.c

@@ -0,0 +1,102 @@
+/*
+ * PowerQUICC II support functions
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "types.h"
+#include "fsl-soc.h"
+#include "pq2.h"
+#include "stdio.h"
+#include "io.h"
+
+#define PQ2_SCCR (0x10c80/4) /* System Clock Configuration Register */
+#define PQ2_SCMR (0x10c88/4) /* System Clock Mode Register */
+
+static int pq2_corecnf_map[] = {
+	3, 2, 2, 2, 4, 4, 5, 9, 6, 11, 8, 10, 3, 12, 7, -1,
+	6, 5, 13, 2, 14, 4, 15, 9, 0, 11, 8, 10, 16, 12, 7, -1
+};
+
+/* Get various clocks from crystal frequency.
+ * Returns zero on failure and non-zero on success.
+ */
+int pq2_get_clocks(u32 crystal, u32 *sysfreq, u32 *corefreq,
+                   u32 *timebase, u32 *brgfreq)
+{
+	u32 *immr;
+	u32 sccr, scmr, mainclk, busclk;
+	int corecnf, busdf, plldf, pllmf, dfbrg;
+
+	immr = fsl_get_immr();
+	if (!immr) {
+		printf("pq2_get_clocks: Couldn't get IMMR base.\r\n");
+		return 0;
+	}
+
+	sccr = in_be32(&immr[PQ2_SCCR]);
+	scmr = in_be32(&immr[PQ2_SCMR]);
+
+	dfbrg = sccr & 3;
+	corecnf = (scmr >> 24) & 0x1f;
+	busdf = (scmr >> 20) & 0xf;
+	plldf = (scmr >> 12) & 1;
+	pllmf = scmr & 0xfff;
+
+	mainclk = crystal * (pllmf + 1) / (plldf + 1);
+	busclk = mainclk / (busdf + 1);
+
+	if (sysfreq)
+		*sysfreq = mainclk / 2;
+	if (timebase)
+		*timebase = busclk / 4;
+	if (brgfreq)
+		*brgfreq = mainclk / (1 << ((dfbrg + 1) * 2));
+
+	if (corefreq) {
+		int coremult = pq2_corecnf_map[corecnf];
+
+		if (coremult < 0)
+			*corefreq = mainclk / 2;
+		else if (coremult == 0)
+			return 0;
+		else
+			*corefreq = busclk * coremult / 2;
+	}
+
+	return 1;
+}
+
+/* Set common device tree fields based on the given clock frequencies. */
+void pq2_set_clocks(u32 sysfreq, u32 corefreq, u32 timebase, u32 brgfreq)
+{
+	void *node;
+
+	dt_fixup_cpu_clocks(corefreq, timebase, sysfreq);
+
+	node = finddevice("/soc/cpm");
+	if (node)
+		setprop(node, "clock-frequency", &sysfreq, 4);
+
+	node = finddevice("/soc/cpm/brg");
+	if (node)
+		setprop(node, "clock-frequency", &brgfreq, 4);
+}
+
+int pq2_fixup_clocks(u32 crystal)
+{
+	u32 sysfreq, corefreq, timebase, brgfreq;
+
+	if (!pq2_get_clocks(crystal, &sysfreq, &corefreq, &timebase, &brgfreq))
+		return 0;
+
+	pq2_set_clocks(sysfreq, corefreq, timebase, brgfreq);
+	return 1;
+}

arch/powerpc/boot/pq2.h

@@ -0,0 +1,11 @@
+#ifndef _PPC_BOOT_PQ2_H_
+#define _PPC_BOOT_PQ2_H_
+
+#include "types.h"
+
+int pq2_get_clocks(u32 crystal, u32 *sysfreq, u32 *corefreq,
+                   u32 *timebase, u32 *brgfreq);
+void pq2_set_clocks(u32 sysfreq, u32 corefreq, u32 timebase, u32 brgfreq);
+int pq2_fixup_clocks(u32 crystal);
+
+#endif

arch/powerpc/boot/prpmc2800.c

@@ -21,12 +21,6 @@
 #include "gunzip_util.h"
 #include "mv64x60.h"
 
-extern char _end[];
-extern char _vmlinux_start[], _vmlinux_end[];
-extern char _dtb_start[], _dtb_end[];
-
-extern void udelay(long delay);
-
 #define KB	1024U
 #define MB	(KB*KB)
 #define GB	(KB*MB)

arch/powerpc/boot/ps3.c

@@ -120,10 +120,6 @@ void ps3_copy_vectors(void)
 
 void platform_init(void)
 {
-	extern char _end[];
-	extern char _dtb_start[];
-	extern char _initrd_start[];
-	extern char _initrd_end[];
 	const u32 heapsize = 0x1000000 - (u32)_end; /* 16MiB */
 	void *chosen;
 	unsigned long ft_addr;

arch/powerpc/boot/serial.c

@@ -19,8 +19,6 @@
 #include "io.h"
 #include "ops.h"
 
-extern void udelay(long delay);
-
 static int serial_open(void)
 {
 	struct serial_console_data *scdp = console_ops.data;
@@ -114,29 +112,36 @@ int serial_console_init(void)
 {
 	void *devp;
 	int rc = -1;
-	char compat[MAX_PROP_LEN];
 
 	devp = serial_get_stdout_devp();
 	if (devp == NULL)
 		goto err_out;
 
-	if (getprop(devp, "compatible", compat, sizeof(compat)) < 0)
-		goto err_out;
-
-	if (!strcmp(compat, "ns16550"))
+	if (dt_is_compatible(devp, "ns16550"))
 		rc = ns16550_console_init(devp, &serial_cd);
-	else if (!strcmp(compat, "marvell,mpsc"))
+	else if (dt_is_compatible(devp, "marvell,mpsc"))
 		rc = mpsc_console_init(devp, &serial_cd);
+	else if (dt_is_compatible(devp, "fsl,cpm1-scc-uart") ||
+	         dt_is_compatible(devp, "fsl,cpm1-smc-uart") ||
+	         dt_is_compatible(devp, "fsl,cpm2-scc-uart") ||
+	         dt_is_compatible(devp, "fsl,cpm2-smc-uart"))
+		rc = cpm_console_init(devp, &serial_cd);
+	else if (dt_is_compatible(devp, "mpc5200-psc-uart"))
+		rc = mpc5200_psc_console_init(devp, &serial_cd);
+	else if (dt_is_compatible(devp, "xilinx,uartlite"))
+		rc = uartlite_console_init(devp, &serial_cd);
 
 	/* Add other serial console driver calls here */
 
 	if (!rc) {
 		console_ops.open = serial_open;
 		console_ops.write = serial_write;
-		console_ops.edit_cmdline = serial_edit_cmdline;
 		console_ops.close = serial_close;
 		console_ops.data = &serial_cd;
 
+		if (serial_cd.getc)
+			console_ops.edit_cmdline = serial_edit_cmdline;
+
 		return 0;
 	}
 err_out:

arch/powerpc/boot/stdlib.c

@@ -0,0 +1,45 @@
+/*
+ * stdlib functions
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "stdlib.h"
+
+/* Not currently supported: leading whitespace, sign, 0x prefix, zero base */
+unsigned long long int strtoull(const char *ptr, char **end, int base)
+{
+	unsigned long long ret = 0;
+
+	if (base > 36)
+		goto out;
+
+	while (*ptr) {
+		int digit;
+
+		if (*ptr >= '0' && *ptr <= '9' && *ptr < '0' + base)
+			digit = *ptr - '0';
+		else if (*ptr >= 'A' && *ptr < 'A' + base - 10)
+			digit = *ptr - 'A' + 10;
+		else if (*ptr >= 'a' && *ptr < 'a' + base - 10)
+			digit = *ptr - 'a' + 10;
+		else
+			break;
+
+		ret *= base;
+		ret += digit;
+		ptr++;
+	}
+
+out:
+	if (end)
+		*end = (char *)ptr;
+
+	return ret;
+}

arch/powerpc/boot/stdlib.h

@@ -0,0 +1,6 @@
+#ifndef _PPC_BOOT_STDLIB_H_
+#define _PPC_BOOT_STDLIB_H_
+
+unsigned long long int strtoull(const char *ptr, char **end, int base);
+
+#endif

arch/powerpc/boot/string.S

@@ -49,6 +49,17 @@ strcat:
 	bne	1b
 	blr
 
+	.globl	strchr
+strchr:
+	addi	r3,r3,-1
+1:	lbzu	r0,1(r3)
+	cmpw	0,r0,r4
+	beqlr
+	cmpwi	0,r0,0
+	bne	1b
+	li	r3,0
+	blr
+
 	.globl	strcmp
 strcmp:
 	addi	r5,r3,-1
@@ -61,6 +72,19 @@ strcmp:
 	beq	1b
 	blr
 
+	.globl	strncmp
+strncmp:
+	mtctr	r5
+	addi	r5,r3,-1
+	addi	r4,r4,-1
+1:	lbzu	r3,1(r5)
+	cmpwi	1,r3,0
+	lbzu	r0,1(r4)
+	subf.	r3,r0,r3
+	beqlr	1
+	bdnzt	eq,1b
+	blr
+
 	.globl	strlen
 strlen:
 	addi	r4,r3,-1
@@ -195,6 +219,19 @@ backwards_memcpy:
 	mtctr	r7
 	b	1b
 
+	.globl	memchr
+memchr:
+	cmpwi	0,r5,0
+	blelr
+	mtctr	r5
+	addi	r3,r3,-1
+1:	lbzu	r0,1(r3)
+	cmpw	r0,r4
+	beqlr
+	bdnz	1b
+	li	r3,0
+	blr
+
 	.globl	memcmp
 memcmp:
 	cmpwi	0,r5,0

arch/powerpc/boot/string.h

@@ -5,13 +5,16 @@
 extern char *strcpy(char *dest, const char *src);
 extern char *strncpy(char *dest, const char *src, size_t n);
 extern char *strcat(char *dest, const char *src);
+extern char *strchr(const char *s, int c);
 extern int strcmp(const char *s1, const char *s2);
+extern int strncmp(const char *s1, const char *s2, size_t n);
 extern size_t strlen(const char *s);
 extern size_t strnlen(const char *s, size_t count);
 
 extern void *memset(void *s, int c, size_t n);
 extern void *memmove(void *dest, const void *src, unsigned long n);
 extern void *memcpy(void *dest, const void *src, unsigned long n);
+extern void *memchr(const void *s, int c, size_t n);
 extern int memcmp(const void *s1, const void *s2, size_t n);
 
 #endif	/* _PPC_BOOT_STRING_H_ */

arch/powerpc/boot/treeboot-bamboo.c

@@ -0,0 +1,43 @@
+/*
+ * Copyright IBM Corporation, 2007
+ * Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Based on ebony wrapper:
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2 of the License
+ */
+#include "ops.h"
+#include "stdio.h"
+#include "44x.h"
+#include "stdlib.h"
+
+BSS_STACK(4096);
+
+#define PIBS_MAC0 0xfffc0400
+#define PIBS_MAC1 0xfffc0500
+char pibs_mac0[6];
+char pibs_mac1[6];
+
+static void read_pibs_mac(void)
+{
+	unsigned long long mac64;
+
+	mac64 = strtoull((char *)PIBS_MAC0, 0, 16);
+	memcpy(&pibs_mac0, (char *)&mac64+2, 6);
+
+	mac64 = strtoull((char *)PIBS_MAC1, 0, 16);
+	memcpy(&pibs_mac1, (char *)&mac64+2, 6);
+}
+
+void platform_init(void)
+{
+	unsigned long end_of_ram = 0x8000000;
+	unsigned long avail_ram = end_of_ram - (unsigned long)_end;
+
+	simple_alloc_init(_end, avail_ram, 32, 64);
+	read_pibs_mac();
+	bamboo_init((u8 *)&pibs_mac0, (u8 *)&pibs_mac1);
+}

arch/powerpc/boot/treeboot-ebony.c

@@ -16,8 +16,6 @@
 #include "stdio.h"
 #include "44x.h"
 
-extern char _end[];
-
 BSS_STACK(4096);
 
 #define OPENBIOS_MAC_BASE	0xfffffe0c

arch/powerpc/boot/treeboot-walnut.c

@@ -0,0 +1,131 @@
+/*
+ * Old U-boot compatibility for Walnut
+ *
+ * Author: Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Copyright 2007 IBM Corporation
+ *   Based on cuboot-83xx.c, which is:
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "dcr.h"
+#include "4xx.h"
+#include "io.h"
+
+BSS_STACK(4096);
+
+void ibm405gp_fixup_clocks(unsigned int sysclk, unsigned int ser_clk)
+{
+	u32 pllmr = mfdcr(DCRN_CPC0_PLLMR);
+	u32 cpc0_cr0 = mfdcr(DCRN_405_CPC0_CR0);
+	u32 cpc0_cr1 = mfdcr(DCRN_405_CPC0_CR1);
+	u32 cpu, plb, opb, ebc, tb, uart0, uart1, m;
+	u32 fwdv, fbdv, cbdv, opdv, epdv, udiv;
+
+	fwdv = (8 - ((pllmr & 0xe0000000) >> 29));
+	fbdv = (pllmr & 0x1e000000) >> 25;
+	cbdv = ((pllmr & 0x00060000) >> 17) + 1;
+	opdv = ((pllmr & 0x00018000) >> 15) + 1;
+	epdv = ((pllmr & 0x00001800) >> 13) + 2;
+	udiv = ((cpc0_cr0 & 0x3e) >> 1) + 1;
+
+	m = fwdv * fbdv * cbdv;
+
+	cpu = sysclk * m / fwdv;
+	plb = cpu / cbdv;
+	opb = plb / opdv;
+	ebc = plb / epdv;
+
+	if (cpc0_cr0 & 0x80) {
+		/* uart0 uses the external clock */
+		uart0 = ser_clk;
+	} else {
+		uart0 = cpu / udiv;
+	}
+
+	if (cpc0_cr0 & 0x40) {
+		/* uart1 uses the external clock */
+		uart1 = ser_clk;
+	} else {
+		uart1 = cpu / udiv;
+	}
+
+	/* setup the timebase clock to tick at the cpu frequency */
+	cpc0_cr1 = cpc0_cr1 & ~ 0x00800000;
+	mtdcr(DCRN_CPC0_CR1, cpc0_cr1);
+	tb = cpu;
+
+	dt_fixup_cpu_clocks(cpu, tb, 0);
+	dt_fixup_clock("/plb", plb);
+	dt_fixup_clock("/plb/opb", opb);
+	dt_fixup_clock("/plb/ebc", ebc);
+	dt_fixup_clock("/plb/opb/serial@ef600300", uart0);
+	dt_fixup_clock("/plb/opb/serial@ef600400", uart1);
+}
+
+static void walnut_flashsel_fixup(void)
+{
+	void *devp, *sram;
+	u32 reg_flash[3] = {0x0, 0x0, 0x80000};
+	u32 reg_sram[3] = {0x0, 0x0, 0x80000};
+	u8 *fpga;
+	u8 fpga_brds1 = 0x0;
+
+	devp = finddevice("/plb/ebc/fpga");
+	if (!devp)
+		fatal("Couldn't locate FPGA node\n\r");
+
+	if (getprop(devp, "virtual-reg", &fpga, sizeof(fpga)) != sizeof(fpga))
+		fatal("no virtual-reg property\n\r");
+
+	fpga_brds1 = in_8(fpga);
+
+	devp = finddevice("/plb/ebc/flash");
+	if (!devp)
+		fatal("Couldn't locate flash node\n\r");
+
+	if (getprop(devp, "reg", reg_flash, sizeof(reg_flash)) != sizeof(reg_flash))
+		fatal("flash reg property has unexpected size\n\r");
+
+	sram = finddevice("/plb/ebc/sram");
+	if (!sram)
+		fatal("Couldn't locate sram node\n\r");
+
+	if (getprop(sram, "reg", reg_sram, sizeof(reg_sram)) != sizeof(reg_sram))
+		fatal("sram reg property has unexpected size\n\r");
+
+	if (fpga_brds1 & 0x1) {
+		reg_flash[1] ^= 0x80000;
+		reg_sram[1] ^= 0x80000;
+	}
+
+	setprop(devp, "reg", reg_flash, sizeof(reg_flash));
+	setprop(sram, "reg", reg_sram, sizeof(reg_sram));
+}
+
+static void walnut_fixups(void)
+{
+	ibm4xx_fixup_memsize();
+	ibm405gp_fixup_clocks(33330000, 0xa8c000);
+	ibm4xx_quiesce_eth((u32 *)0xef600800, NULL);
+	ibm4xx_fixup_ebc_ranges("/plb/ebc");
+	walnut_flashsel_fixup();
+}
+
+void platform_init(void)
+{
+	unsigned long end_of_ram = 0x2000000;
+	unsigned long avail_ram = end_of_ram - (unsigned long) _end;
+
+	simple_alloc_init(_end, avail_ram, 32, 32);
+	platform_ops.fixups = walnut_fixups;
+	platform_ops.exit = ibm40x_dbcr_reset;
+	ft_init(_dtb_start, _dtb_end - _dtb_start, 32);
+	serial_console_init();
+}

arch/powerpc/boot/uartlite.c

@@ -0,0 +1,79 @@
+/*
+ * Xilinx UARTLITE bootloader driver
+ *
+ * Copyright (C) 2007 Secret Lab Technologies Ltd.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <stdarg.h>
+#include <stddef.h>
+#include "types.h"
+#include "string.h"
+#include "stdio.h"
+#include "io.h"
+#include "ops.h"
+
+#define ULITE_RX		0x00
+#define ULITE_TX		0x04
+#define ULITE_STATUS		0x08
+#define ULITE_CONTROL		0x0c
+
+#define ULITE_STATUS_RXVALID	0x01
+#define ULITE_STATUS_TXFULL	0x08
+
+#define ULITE_CONTROL_RST_RX	0x02
+
+static void * reg_base;
+
+static int uartlite_open(void)
+{
+	/* Clear the RX FIFO */
+	out_be32(reg_base + ULITE_CONTROL, ULITE_CONTROL_RST_RX);
+	return 0;
+}
+
+static void uartlite_putc(unsigned char c)
+{
+	u32 reg = ULITE_STATUS_TXFULL;
+	while (reg & ULITE_STATUS_TXFULL) /* spin on TXFULL bit */
+		reg = in_be32(reg_base + ULITE_STATUS);
+	out_be32(reg_base + ULITE_TX, c);
+}
+
+static unsigned char uartlite_getc(void)
+{
+	u32 reg = 0;
+	while (!(reg & ULITE_STATUS_RXVALID)) /* spin waiting for RXVALID bit */
+		reg = in_be32(reg_base + ULITE_STATUS);
+	return in_be32(reg_base + ULITE_RX);
+}
+
+static u8 uartlite_tstc(void)
+{
+	u32 reg = in_be32(reg_base + ULITE_STATUS);
+	return reg & ULITE_STATUS_RXVALID;
+}
+
+int uartlite_console_init(void *devp, struct serial_console_data *scdp)
+{
+	int n;
+	unsigned long reg_phys;
+
+	n = getprop(devp, "virtual-reg", &reg_base, sizeof(reg_base));
+	if (n != sizeof(reg_base)) {
+		if (!dt_xlate_reg(devp, 0, &reg_phys, NULL))
+			return -1;
+
+		reg_base = (void *)reg_phys;
+	}
+
+	scdp->open = uartlite_open;
+	scdp->putc = uartlite_putc;
+	scdp->getc = uartlite_getc;
+	scdp->tstc = uartlite_tstc;
+	scdp->close = NULL;
+	return 0;
+}

arch/powerpc/boot/wrapper

@@ -29,6 +29,7 @@ initrd=
 dtb=
 dts=
 cacheit=
+binary=
 gzip=.gz
 
 # cross-compilation prefix
@@ -142,17 +143,23 @@ miboot|uboot)
     isection=initrd
     ;;
 cuboot*)
+    binary=y
     gzip=
     ;;
 ps3)
     platformo="$object/ps3-head.o $object/ps3-hvcall.o $object/ps3.o"
     lds=$object/zImage.ps3.lds
+    binary=y
     gzip=
     ext=bin
     objflags="-O binary --set-section-flags=.bss=contents,alloc,load,data"
     ksection=.kernel:vmlinux.bin
     isection=.kernel:initrd
     ;;
+ep88xc)
+    platformo="$object/fixed-head.o $object/$platform.o"
+    binary=y
+    ;;
 esac
 
 vmz="$tmpdir/`basename \"$kernel\"`.$ext"
@@ -224,6 +231,11 @@ fi
 base=0x`${CROSS}nm "$ofile" | grep ' _start$' | cut -d' ' -f1`
 entry=`${CROSS}objdump -f "$ofile" | grep '^start address ' | cut -d' ' -f3`
 
+if [ -n "$binary" ]; then
+    mv "$ofile" "$ofile".elf
+    ${CROSS}objcopy -O binary "$ofile".elf "$ofile".bin
+fi
+
 # post-processing needed for some platforms
 case "$platform" in
 pseries|chrp)
@@ -234,8 +246,6 @@ coff)
     $object/hack-coff "$ofile"
     ;;
 cuboot*)
-    mv "$ofile" "$ofile".elf
-    ${CROSS}objcopy -O binary "$ofile".elf "$ofile".bin
     gzip -f -9 "$ofile".bin
     mkimage -A ppc -O linux -T kernel -C gzip -a "$base" -e "$entry" \
             $uboot_version -d "$ofile".bin.gz "$ofile"
@@ -259,11 +269,11 @@ ps3)
     # then copied to offset 0x100.  At runtime the bootwrapper program
     # copies the 0x100 bytes at __system_reset_kernel to addr 0x100.
 
-    system_reset_overlay=0x`${CROSS}nm "$ofile" \
+    system_reset_overlay=0x`${CROSS}nm "$ofile".elf \
         | grep ' __system_reset_overlay$'       \
         | cut -d' ' -f1`
     system_reset_overlay=`printf "%d" $system_reset_overlay`
-    system_reset_kernel=0x`${CROSS}nm "$ofile" \
+    system_reset_kernel=0x`${CROSS}nm "$ofile".elf \
         | grep ' __system_reset_kernel$'       \
         | cut -d' ' -f1`
     system_reset_kernel=`printf "%d" $system_reset_kernel`
@@ -272,8 +282,6 @@ ps3)
 
     rm -f "$object/otheros.bld"
 
-    ${CROSS}objcopy -O binary "$ofile" "$ofile.bin"
-
     msg=$(dd if="$ofile.bin" of="$ofile.bin" conv=notrunc \
         skip=$overlay_dest seek=$system_reset_kernel      \
         count=$overlay_size bs=1 2>&1)

arch/powerpc/configs/bamboo_defconfig

@@ -0,0 +1,775 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.23-rc1
+# Fri Aug  3 10:46:53 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+CONFIG_44x=y
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+CONFIG_4xx=y
+CONFIG_BOOKE=y
+CONFIG_PTE_64BIT=y
+CONFIG_PHYS_64BIT=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_BAMBOO=y
+# CONFIG_EBONY is not set
+CONFIG_440EP=y
+CONFIG_IBM440EP_ERR42=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE=""
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="bamboo.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+# CONFIG_PCI_DEBUG is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x01000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+CONFIG_CONNECTOR=y
+CONFIG_PROC_EVENTS=y
+# CONFIG_MTD is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=35000
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_XILINX_SYSACE is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+CONFIG_MACINTOSH_DRIVERS=y
+# CONFIG_MAC_EMUMOUSEBTN is not set
+# CONFIG_WINDFARM is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_ARCNET is not set
+# CONFIG_NET_ETHERNET is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=m
+# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+CONFIG_DEBUGGER=y
+# CONFIG_KGDB is not set
+# CONFIG_XMON is not set
+# CONFIG_BDI_SWITCH is not set
+CONFIG_PPC_EARLY_DEBUG=y
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS_PANEL is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS_CONSOLE is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
+# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set
+# CONFIG_PPC_EARLY_DEBUG_BEAT is not set
+CONFIG_PPC_EARLY_DEBUG_44x=y
+CONFIG_PPC_EARLY_DEBUG_44x_PHYSLOW=0xef600300
+CONFIG_PPC_EARLY_DEBUG_44x_PHYSHIGH=0x0
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+CONFIG_CRYPTO_HW=y

arch/powerpc/configs/ebony_defconfig

@@ -313,7 +313,80 @@ CONFIG_FW_LOADER=y
 # CONFIG_SYS_HYPERVISOR is not set
 CONFIG_CONNECTOR=y
 CONFIG_PROC_EVENTS=y
-# CONFIG_MTD is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
@@ -607,6 +680,15 @@ CONFIG_RAMFS=y
 # CONFIG_BEFS_FS is not set
 # CONFIG_BFS_FS is not set
 # CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
 CONFIG_CRAMFS=y
 # CONFIG_VXFS_FS is not set
 # CONFIG_HPFS_FS is not set
@@ -665,6 +747,7 @@ CONFIG_CRC32=y
 # CONFIG_CRC7 is not set
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
 CONFIG_PLIST=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y

arch/powerpc/configs/ep88xc_defconfig

@@ -0,0 +1,751 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.23-rc6
+# Fri Sep 14 14:59:56 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+CONFIG_PPC_8xx=y
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_8xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_FUTEX is not set
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=1
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+CONFIG_IOSCHED_DEADLINE=y
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+CONFIG_DEFAULT_DEADLINE=y
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="deadline"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+CONFIG_CPM1=y
+# CONFIG_MPC8XXFADS is not set
+# CONFIG_MPC86XADS is not set
+# CONFIG_MPC885ADS is not set
+CONFIG_PPC_EP88XC=y
+
+#
+# MPC8xx CPM Options
+#
+
+#
+# Generic MPC8xx Options
+#
+CONFIG_8xx_COPYBACK=y
+# CONFIG_8xx_CPU6 is not set
+CONFIG_8xx_CPU15=y
+CONFIG_NO_UCODE_PATCH=y
+# CONFIG_USB_SOF_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_UCODE_PATCH is not set
+# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+CONFIG_HZ_100=y
+# CONFIG_HZ_250 is not set
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=100
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+# CONFIG_SECCOMP is not set
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="ep88xc.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_FSL_SOC=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_PCI_QSPAN is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xfd000000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_CFI_FLAGADM is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+CONFIG_LXT_PHY=y
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FEC=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+# CONFIG_SERIAL_CPM_SCC1 is not set
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+# CONFIG_SERIAL_CPM_SCC4 is not set
+CONFIG_SERIAL_CPM_SMC1=y
+CONFIG_SERIAL_CPM_SMC2=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+# CONFIG_PROC_KCORE is not set
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+# CONFIG_CRC32 is not set
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_CRYPTO is not set

arch/powerpc/configs/kilauea_defconfig

@@ -0,0 +1,768 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.23-rc9
+# Thu Oct 11 19:05:15 2007
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+CONFIG_40x=y
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_4xx=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_KALLSYMS_EXTRA_PASS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_KILAUEA=y
+# CONFIG_WALNUT is not set
+# CONFIG_XILINX_VIRTEX_GENERIC_BOARD is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_MATH_EMULATION is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SUSPEND_UP_POSSIBLE=y
+CONFIG_HIBERNATION_UP_POSSIBLE=y
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="kilauea.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+# CONFIG_PCI is not set
+# CONFIG_PCI_DOMAINS is not set
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x00400000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+CONFIG_CONNECTOR=y
+CONFIG_PROC_EVENTS=y
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=m
+CONFIG_MTD_BLOCK=m
+# CONFIG_MTD_BLOCK_RO is not set
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=35000
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_XILINX_SYSACE is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_NET_ETHERNET is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# Userspace I/O
+#
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_PPC_CLOCK is not set

arch/powerpc/configs/mpc8272_ads_defconfig

@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.23-rc4
-# Tue Aug 28 21:24:39 2007
+# Wed Sep  5 12:43:23 2007
 #
 # CONFIG_PPC64 is not set
 
@@ -52,7 +52,7 @@ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
 # CONFIG_EXPERIMENTAL is not set
 CONFIG_BROKEN_ON_SMP=y
 CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION="powerpc8272"
+CONFIG_LOCALVERSION=""
 CONFIG_LOCALVERSION_AUTO=y
 CONFIG_SWAP=y
 CONFIG_SYSVIPC=y
@@ -71,7 +71,7 @@ CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -122,10 +122,11 @@ CONFIG_PPC_82xx=y
 # CONFIG_PPC_MPC5200 is not set
 # CONFIG_PPC_CELL is not set
 # CONFIG_PPC_CELL_NATIVE is not set
-CONFIG_MPC82xx_ADS=y
+CONFIG_MPC8272_ADS=y
 CONFIG_PQ2ADS=y
 CONFIG_8260=y
 CONFIG_8272=y
+CONFIG_PQ2_ADS_PCI_PIC=y
 # CONFIG_MPIC is not set
 # CONFIG_MPIC_WEIRD is not set
 # CONFIG_PPC_I8259 is not set
@@ -137,7 +138,9 @@ CONFIG_8272=y
 # CONFIG_GENERIC_IOMAP is not set
 # CONFIG_CPU_FREQ is not set
 CONFIG_CPM2=y
+CONFIG_PPC_CPM_NEW_BINDING=y
 # CONFIG_FSL_ULI1575 is not set
+CONFIG_CPM=y
 
 #
 # Kernel options
@@ -168,18 +171,25 @@ CONFIG_PROC_DEVICETREE=y
 # CONFIG_CMDLINE_BOOL is not set
 # CONFIG_PM is not set
 CONFIG_SECCOMP=y
-# CONFIG_WANT_DEVICE_TREE is not set
+CONFIG_WANT_DEVICE_TREE=y
+# CONFIG_BUILD_RAW_IMAGE is not set
+CONFIG_DEVICE_TREE="mpc8272ads.dts"
 CONFIG_ISA_DMA_API=y
 
 #
 # Bus options
 #
 CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
 CONFIG_FSL_SOC=y
-# CONFIG_PCI is not set
-# CONFIG_PCI_DOMAINS is not set
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+CONFIG_PCI_8260=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+# CONFIG_PCI_DEBUG is not set
 
 #
 # PCCARD (PCMCIA/CardBus) support
@@ -313,43 +323,101 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_DEBUG_DEVRES is not set
 # CONFIG_SYS_HYPERVISOR is not set
 # CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_PARTITIONS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+CONFIG_MTD_CFI_GEOMETRY=y
+# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_2 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+# CONFIG_MTD_CFI_I1 is not set
+# CONFIG_MTD_CFI_I2 is not set
+CONFIG_MTD_CFI_I4=y
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_OTP is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_SBC8240 is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
 # CONFIG_BLK_DEV_COW_COMMON is not set
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_BLK_DEV_CRYPTOLOOP is not set
 # CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
 # CONFIG_BLK_DEV_RAM is not set
 # CONFIG_CDROM_PKTCDVD is not set
 # CONFIG_ATA_OVER_ETH is not set
-CONFIG_MISC_DEVICES=y
-# CONFIG_EEPROM_93CX6 is not set
-CONFIG_IDE=y
-CONFIG_IDE_MAX_HWIFS=4
-CONFIG_BLK_DEV_IDE=y
-
-#
-# Please see Documentation/ide.txt for help/info on IDE drives
-#
-# CONFIG_BLK_DEV_IDE_SATA is not set
-CONFIG_BLK_DEV_IDEDISK=y
-# CONFIG_IDEDISK_MULTI_MODE is not set
-# CONFIG_BLK_DEV_IDECD is not set
-# CONFIG_BLK_DEV_IDEFLOPPY is not set
-# CONFIG_IDE_TASK_IOCTL is not set
-CONFIG_IDE_PROC_FS=y
-
-#
-# IDE chipset support/bugfixes
-#
-# CONFIG_IDE_GENERIC is not set
-# CONFIG_IDEPCI_PCIBUS_ORDER is not set
-# CONFIG_IDE_ARM is not set
-# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_BLK_DEV_HD is not set
+# CONFIG_MISC_DEVICES is not set
+# CONFIG_IDE is not set
 
 #
 # SCSI device support
@@ -360,6 +428,21 @@ CONFIG_IDE_PROC_FS=y
 # CONFIG_SCSI_NETLINK is not set
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# An alternative FireWire stack is available with EXPERIMENTAL=y
+#
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
 # CONFIG_NETDEVICES_MULTIQUEUE is not set
@@ -367,6 +450,7 @@ CONFIG_NETDEVICES=y
 # CONFIG_BONDING is not set
 # CONFIG_EQUALIZER is not set
 CONFIG_TUN=y
+# CONFIG_ARCNET is not set
 CONFIG_PHYLIB=y
 
 #
@@ -382,13 +466,42 @@ CONFIG_DAVICOM_PHY=y
 # CONFIG_BROADCOM_PHY is not set
 # CONFIG_ICPLUS_PHY is not set
 # CONFIG_FIXED_PHY is not set
+CONFIG_MDIO_BITBANG=y
 CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_NET_PCI is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
 CONFIG_FS_ENET_HAS_FCC=y
 CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
 CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TR is not set
 
 #
 # Wireless LAN
@@ -396,6 +509,7 @@ CONFIG_NETDEV_10000=y
 # CONFIG_WLAN_PRE80211 is not set
 # CONFIG_WLAN_80211 is not set
 # CONFIG_WAN is not set
+# CONFIG_FDDI is not set
 CONFIG_PPP=y
 # CONFIG_PPP_FILTER is not set
 CONFIG_PPP_ASYNC=y
@@ -459,6 +573,7 @@ CONFIG_MOUSE_PS2_TRACKPOINT=y
 CONFIG_SERIO=y
 # CONFIG_SERIO_I8042 is not set
 CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_PCIPS2 is not set
 CONFIG_SERIO_LIBPS2=y
 # CONFIG_SERIO_RAW is not set
 # CONFIG_GAMEPORT is not set
@@ -488,6 +603,7 @@ CONFIG_SERIAL_CPM_SCC1=y
 CONFIG_SERIAL_CPM_SCC4=y
 # CONFIG_SERIAL_CPM_SMC1 is not set
 # CONFIG_SERIAL_CPM_SMC2 is not set
+# CONFIG_SERIAL_JSM is not set
 CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=256
@@ -497,7 +613,11 @@ CONFIG_HW_RANDOM=y
 # CONFIG_NVRAM is not set
 # CONFIG_GEN_RTC is not set
 # CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
 # CONFIG_RAW_DRIVER is not set
+CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 
 #
@@ -531,7 +651,7 @@ CONFIG_DAB=y
 #
 # CONFIG_DISPLAY_SUPPORT is not set
 # CONFIG_VGASTATE is not set
-CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
 # CONFIG_FB is not set
 # CONFIG_FB_IBM_GXT4500 is not set
 
@@ -539,45 +659,11 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y
 # Sound
 #
 # CONFIG_SOUND is not set
-CONFIG_HID_SUPPORT=y
-CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
-CONFIG_USB_SUPPORT=y
-# CONFIG_USB_ARCH_HAS_HCD is not set
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-# CONFIG_USB_ARCH_HAS_EHCI is not set
-
-#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-#
-
-#
-# USB Gadget Support
-#
-CONFIG_USB_GADGET=y
-# CONFIG_USB_GADGET_DEBUG_FILES is not set
-CONFIG_USB_GADGET_SELECTED=y
-# CONFIG_USB_GADGET_AMD5536UDC is not set
-# CONFIG_USB_GADGET_FSL_USB2 is not set
-# CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_PXA2XX is not set
-CONFIG_USB_GADGET_M66592=y
-CONFIG_USB_M66592=y
-# CONFIG_USB_GADGET_GOKU is not set
-# CONFIG_USB_GADGET_LH7A40X is not set
-# CONFIG_USB_GADGET_OMAP is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
-# CONFIG_USB_GADGET_AT91 is not set
-# CONFIG_USB_GADGET_DUMMY_HCD is not set
-CONFIG_USB_GADGET_DUALSPEED=y
-# CONFIG_USB_ZERO is not set
-CONFIG_USB_ETH=y
-# CONFIG_USB_GADGETFS is not set
-# CONFIG_USB_FILE_STORAGE is not set
-# CONFIG_USB_G_SERIAL is not set
-# CONFIG_USB_MIDI_GADGET is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
 # CONFIG_MMC is not set
 # CONFIG_NEW_LEDS is not set
+# CONFIG_INFINIBAND is not set
 # CONFIG_RTC_CLASS is not set
 
 #
@@ -614,11 +700,7 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_XFS_FS=y
-# CONFIG_XFS_QUOTA is not set
-# CONFIG_XFS_SECURITY is not set
-# CONFIG_XFS_POSIX_ACL is not set
-# CONFIG_XFS_RT is not set
+# CONFIG_XFS_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_MINIX_FS is not set
 # CONFIG_ROMFS_FS is not set
@@ -659,6 +741,7 @@ CONFIG_RAMFS=y
 # Miscellaneous filesystems
 #
 # CONFIG_HFSPLUS_FS is not set
+# CONFIG_JFFS2_FS is not set
 CONFIG_CRAMFS=y
 # CONFIG_VXFS_FS is not set
 # CONFIG_HPFS_FS is not set
@@ -680,8 +763,7 @@ CONFIG_LOCKD_V4=y
 CONFIG_NFS_ACL_SUPPORT=y
 CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
-CONFIG_SMB_FS=y
-# CONFIG_SMB_NLS_DEFAULT is not set
+# CONFIG_SMB_FS is not set
 # CONFIG_CIFS is not set
 # CONFIG_NCP_FS is not set
 # CONFIG_CODA_FS is not set
@@ -775,7 +857,7 @@ CONFIG_HAS_DMA=y
 #
 # CONFIG_PRINTK_TIME is not set
 CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
+CONFIG_MAGIC_SYSRQ=y
 # CONFIG_UNUSED_SYMBOLS is not set
 # CONFIG_DEBUG_FS is not set
 # CONFIG_HEADERS_CHECK is not set
@@ -793,7 +875,7 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_BUGVERBOSE=y
 CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_VM is not set
 # CONFIG_DEBUG_LIST is not set
@@ -845,4 +927,4 @@ CONFIG_CRYPTO_DES=y
 # CONFIG_CRYPTO_MICHAEL_MIC is not set
 # CONFIG_CRYPTO_CRC32C is not set
 # CONFIG_CRYPTO_CAMELLIA is not set
-CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_HW is not set