MIPS: PNX8550: Remove support for SOC and JBS and STB810 boards.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/Kbuild.platforms

@@ -20,7 +20,6 @@ platforms += mti-sead3
 platforms += netlogic
 platforms += pmc-sierra
 platforms += pnx833x
-platforms += pnx8550
 platforms += powertv
 platforms += rb532
 platforms += sgi-ip22

arch/mips/Kconfig

@@ -385,16 +385,6 @@ config NXP_STB225
 	help
 	 Support for NXP Semiconductors STB225 Development Board.
 
-config PNX8550_JBS
-	bool "NXP PNX8550 based JBS board"
-	select PNX8550
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-
-config PNX8550_STB810
-	bool "NXP PNX8550 based STB810 board"
-	select PNX8550
-	select SYS_SUPPORTS_LITTLE_ENDIAN
-
 config PMC_MSP
 	bool "PMC-Sierra MSP chipsets"
 	depends on EXPERIMENTAL
@@ -1113,19 +1103,6 @@ config SOC_PNX8335
 	bool
 	select SOC_PNX833X
 
-config PNX8550
-	bool
-	select SOC_PNX8550
-
-config SOC_PNX8550
-	bool
-	select DMA_NONCOHERENT
-	select HW_HAS_PCI
-	select SYS_HAS_CPU_MIPS32_R1
-	select SYS_HAS_EARLY_PRINTK
-	select SYS_SUPPORTS_32BIT_KERNEL
-	select GENERIC_GPIO
-
 config SWAP_IO_SPACE
 	bool
 

arch/mips/configs/pnx8550_jbs_defconfig

@@ -1,98 +0,0 @@
-CONFIG_PNX8550_JBS=y
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_PCI=y
-CONFIG_PM=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_XFRM_MIGRATE=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_TCP_MD5SIG=y
-# CONFIG_IPV6 is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_SGI_IOC4=m
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=m
-CONFIG_IDE_GENERIC=y
-CONFIG_BLK_DEV_OFFBOARD=y
-CONFIG_BLK_DEV_GENERIC=y
-CONFIG_BLK_DEV_HPT366=y
-CONFIG_BLK_DEV_IT8213=m
-CONFIG_BLK_DEV_TC86C001=m
-CONFIG_SCSI=y
-CONFIG_SCSI_TGT=m
-CONFIG_BLK_DEV_SD=y
-CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SCAN_ASYNC=y
-CONFIG_SCSI_FC_ATTRS=y
-CONFIG_ISCSI_TCP=m
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_8139TOO=y
-# CONFIG_8139TOO_PIO is not set
-CONFIG_8139TOO_TUNE_TWISTER=y
-CONFIG_8139TOO_8129=y
-CONFIG_CHELSIO_T3=m
-CONFIG_NETXEN_NIC=m
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO_I8042 is not set
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIO_LIBPS2=y
-CONFIG_SERIAL_PNX8XXX=y
-CONFIG_SERIAL_PNX8XXX_CONSOLE=y
-CONFIG_HW_RANDOM=y
-# CONFIG_VGA_CONSOLE is not set
-# CONFIG_HID is not set
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_STORAGE_DATAFAB=y
-CONFIG_USB_STORAGE_FREECOM=y
-CONFIG_USB_STORAGE_ISD200=y
-CONFIG_USB_STORAGE_USBAT=y
-CONFIG_USB_STORAGE_SDDR09=y
-CONFIG_USB_STORAGE_SDDR55=y
-CONFIG_USB_STORAGE_JUMPSHOT=y
-CONFIG_EXT2_FS=y
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_NFSD=m
-CONFIG_DLM=m
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_SLAB=y
-CONFIG_DEBUG_MUTEXES=y
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE="console=ttyS1,38400n8 root=/dev/nfs ip=bootp"
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_LRW=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_CAMELLIA=m
-CONFIG_CRYPTO_FCRYPT=m
-CONFIG_CRC_CCITT=m

arch/mips/configs/pnx8550_stb810_defconfig

@@ -1,92 +0,0 @@
-CONFIG_PNX8550_STB810=y
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_PCI=y
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_XFRM_MIGRATE=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IPV6 is not set
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=m
-CONFIG_IDE_GENERIC=y
-CONFIG_BLK_DEV_OFFBOARD=y
-CONFIG_BLK_DEV_GENERIC=y
-CONFIG_BLK_DEV_HPT366=y
-CONFIG_BLK_DEV_IT8213=m
-CONFIG_BLK_DEV_TC86C001=m
-CONFIG_SCSI=y
-CONFIG_SCSI_TGT=m
-CONFIG_BLK_DEV_SD=y
-CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_SCAN_ASYNC=y
-CONFIG_ISCSI_TCP=m
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_NET_PCI=y
-CONFIG_NATSEMI=y
-CONFIG_CHELSIO_T3=m
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO_I8042 is not set
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIO_LIBPS2=y
-CONFIG_HW_RANDOM=y
-# CONFIG_VGA_CONSOLE is not set
-# CONFIG_HID is not set
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_STORAGE_DATAFAB=y
-CONFIG_USB_STORAGE_FREECOM=y
-CONFIG_USB_STORAGE_ISD200=y
-CONFIG_USB_STORAGE_USBAT=y
-CONFIG_USB_STORAGE_SDDR09=y
-CONFIG_USB_STORAGE_SDDR55=y
-CONFIG_USB_STORAGE_JUMPSHOT=y
-CONFIG_EXT2_FS=y
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_NFSD=m
-CONFIG_DLM=m
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_HEADERS_CHECK=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_SLAB=y
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE="console=ttyS1,38400n8 root=/dev/nfs ip=bootp"
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_LRW=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_CAMELLIA=m
-CONFIG_CRYPTO_FCRYPT=m
-CONFIG_CRC_CCITT=m

arch/mips/include/asm/mach-pnx8550/cm.h

@@ -1,43 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *   Clock module specific definitions
- *
- * Author: source@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-
-#ifndef __PNX8550_CM_H
-#define __PNX8550_CM_H
-
-#define PNX8550_CM_BASE	0xBBE47000
-
-#define PNX8550_CM_PLL0_CTL    *(volatile unsigned long *)(PNX8550_CM_BASE + 0x000)
-#define PNX8550_CM_PLL1_CTL    *(volatile unsigned long *)(PNX8550_CM_BASE + 0x004)
-#define PNX8550_CM_PLL2_CTL    *(volatile unsigned long *)(PNX8550_CM_BASE + 0x008)
-#define PNX8550_CM_PLL3_CTL    *(volatile unsigned long *)(PNX8550_CM_BASE + 0x00C)
-
-// Table not complete.....
-
-#define PNX8550_CM_PLL_BLOCKED_MASK     0x80000000
-#define PNX8550_CM_PLL_LOCK_MASK        0x40000000
-#define PNX8550_CM_PLL_CURRENT_ADJ_MASK 0x3c000000
-#define PNX8550_CM_PLL_N_MASK           0x01ff0000
-#define PNX8550_CM_PLL_M_MASK           0x00003f00
-#define PNX8550_CM_PLL_P_MASK           0x0000000c
-#define PNX8550_CM_PLL_PD_MASK          0x00000002
-
-
-#endif

arch/mips/include/asm/mach-pnx8550/glb.h

@@ -1,86 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *   PNX8550 global definitions
- *
- * Author: source@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-
-#ifndef __PNX8550_GLB_H
-#define __PNX8550_GLB_H
-
-#define PNX8550_GLB1_BASE	0xBBE63000
-#define PNX8550_GLB2_BASE	0xBBE4d000
-#define PNX8550_RESET_BASE      0xBBE60000
-
-/* PCI Inta Output Enable Registers */
-#define PNX8550_GLB2_ENAB_INTA_O	*(volatile unsigned long *)(PNX8550_GLB2_BASE + 0x050)
-
-/* Bit 1:Enable DAC Powerdown
-     0:DACs are enabled and are working normally
-     1:DACs are powerdown
-*/
-#define PNX8550_GLB_DAC_PD      0x2
-/*   Bit 0:Enable of PCI inta output
-     0 = Disable PCI inta output
-     1 = Enable PCI inta output
-*/
-#define PNX8550_GLB_ENABLE_INTA_O 0x1
-
-/* PCI Direct Mappings */
-#define PNX8550_PCIMEM	        0x12000000
-#define PNX8550_PCIMEM_SIZE	0x08000000
-#define PNX8550_PCIIO	        0x1c000000
-#define PNX8550_PCIIO_SIZE	0x02000000	/* 32M */
-
-#define PNX8550_PORT_BASE	KSEG1
-
-// GPIO def
-#define PNX8550_GPIO_BASE	0x1Be00000
-
-#define PNX8550_GPIO_DIRQ0	 (PNX8550_GPIO_BASE + 0x104500)
-#define PNX8550_GPIO_MC1         (PNX8550_GPIO_BASE + 0x104004)
-#define PNX8550_GPIO_MC_31_BIT   30
-#define PNX8550_GPIO_MC_30_BIT   28
-#define PNX8550_GPIO_MC_29_BIT   26
-#define PNX8550_GPIO_MC_28_BIT   24
-#define PNX8550_GPIO_MC_27_BIT   22
-#define PNX8550_GPIO_MC_26_BIT   20
-#define PNX8550_GPIO_MC_25_BIT   18
-#define PNX8550_GPIO_MC_24_BIT   16
-#define PNX8550_GPIO_MC_23_BIT   14
-#define PNX8550_GPIO_MC_22_BIT   12
-#define PNX8550_GPIO_MC_21_BIT   10
-#define PNX8550_GPIO_MC_20_BIT   8
-#define PNX8550_GPIO_MC_19_BIT   6
-#define PNX8550_GPIO_MC_18_BIT   4
-#define PNX8550_GPIO_MC_17_BIT   2
-#define PNX8550_GPIO_MC_16_BIT   0
-
-#define PNX8550_GPIO_MODE_PRIMOP    0x1
-#define PNX8550_GPIO_MODE_NO_OPENDR 0x2
-#define PNX8550_GPIO_MODE_OPENDR    0x3
-
-// RESET module
-#define PNX8550_RST_CTL             *(volatile unsigned long *)(PNX8550_RESET_BASE + 0x0)
-#define PNX8550_RST_CAUSE           *(volatile unsigned long *)(PNX8550_RESET_BASE + 0x4)
-#define PNX8550_RST_EN_WATCHDOG     *(volatile unsigned long *)(PNX8550_RESET_BASE + 0x8)
-
-#define PNX8550_RST_REL_MIPS_RST_N     0x8
-#define PNX8550_RST_DO_SW_RST          0x4
-#define PNX8550_RST_REL_SYS_RST_OUT    0x2
-#define PNX8550_RST_ASSERT_SYS_RST_OUT 0x1
-#endif

arch/mips/include/asm/mach-pnx8550/int.h

@@ -1,140 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *   Interrupt specific definitions
- *
- * Author: source@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-
-#ifndef __PNX8550_INT_H
-#define __PNX8550_INT_H
-
-#define PNX8550_GIC_BASE	0xBBE3E000
-
-#define PNX8550_GIC_PRIMASK_0	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x000)
-#define PNX8550_GIC_PRIMASK_1	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x004)
-#define PNX8550_GIC_VECTOR_0	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x100)
-#define PNX8550_GIC_VECTOR_1	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x104)
-#define PNX8550_GIC_PEND_1_31	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x200)
-#define PNX8550_GIC_PEND_32_63	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x204)
-#define PNX8550_GIC_PEND_64_70	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x208)
-#define PNX8550_GIC_FEATURES	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x300)
-#define PNX8550_GIC_REQ(x)	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0x400 + (x)*4)
-#define PNX8550_GIC_MOD_ID	*(volatile unsigned long *)(PNX8550_GIC_BASE + 0xFFC)
-
-// cp0 is two software + six hw exceptions
-#define PNX8550_INT_CP0_TOTINT	8
-#define PNX8550_INT_CP0_MIN	0
-#define PNX8550_INT_CP0_MAX	(PNX8550_INT_CP0_MIN + PNX8550_INT_CP0_TOTINT - 1)
-
-#define MIPS_CPU_GIC_IRQ        2
-#define MIPS_CPU_TIMER_IRQ      7
-
-// GIC are 71 exceptions connected to cp0's first hardware exception
-#define PNX8550_INT_GIC_TOTINT	71
-#define PNX8550_INT_GIC_MIN	(PNX8550_INT_CP0_MAX+1)
-#define PNX8550_INT_GIC_MAX	(PNX8550_INT_GIC_MIN + PNX8550_INT_GIC_TOTINT - 1)
-
-#define PNX8550_INT_UNDEF              (PNX8550_INT_GIC_MIN+0)
-#define PNX8550_INT_IPC_TARGET0_MIPS   (PNX8550_INT_GIC_MIN+1)
-#define PNX8550_INT_IPC_TARGET1_TM32_1 (PNX8550_INT_GIC_MIN+2)
-#define PNX8550_INT_IPC_TARGET1_TM32_2 (PNX8550_INT_GIC_MIN+3)
-#define PNX8550_INT_RESERVED_4         (PNX8550_INT_GIC_MIN+4)
-#define PNX8550_INT_USB                (PNX8550_INT_GIC_MIN+5)
-#define PNX8550_INT_GPIO_EQ1           (PNX8550_INT_GIC_MIN+6)
-#define PNX8550_INT_GPIO_EQ2           (PNX8550_INT_GIC_MIN+7)
-#define PNX8550_INT_GPIO_EQ3           (PNX8550_INT_GIC_MIN+8)
-#define PNX8550_INT_GPIO_EQ4           (PNX8550_INT_GIC_MIN+9)
-
-#define PNX8550_INT_GPIO_EQ5           (PNX8550_INT_GIC_MIN+10)
-#define PNX8550_INT_GPIO_EQ6           (PNX8550_INT_GIC_MIN+11)
-#define PNX8550_INT_RESERVED_12        (PNX8550_INT_GIC_MIN+12)
-#define PNX8550_INT_QVCP1              (PNX8550_INT_GIC_MIN+13)
-#define PNX8550_INT_QVCP2              (PNX8550_INT_GIC_MIN+14)
-#define PNX8550_INT_I2C1               (PNX8550_INT_GIC_MIN+15)
-#define PNX8550_INT_I2C2               (PNX8550_INT_GIC_MIN+16)
-#define PNX8550_INT_ISO_UART1          (PNX8550_INT_GIC_MIN+17)
-#define PNX8550_INT_ISO_UART2          (PNX8550_INT_GIC_MIN+18)
-#define PNX8550_INT_UART1              (PNX8550_INT_GIC_MIN+19)
-
-#define PNX8550_INT_UART2              (PNX8550_INT_GIC_MIN+20)
-#define PNX8550_INT_QNTR               (PNX8550_INT_GIC_MIN+21)
-#define PNX8550_INT_RESERVED22         (PNX8550_INT_GIC_MIN+22)
-#define PNX8550_INT_T_DSC              (PNX8550_INT_GIC_MIN+23)
-#define PNX8550_INT_M_DSC              (PNX8550_INT_GIC_MIN+24)
-#define PNX8550_INT_RESERVED25         (PNX8550_INT_GIC_MIN+25)
-#define PNX8550_INT_2D_DRAW_ENG        (PNX8550_INT_GIC_MIN+26)
-#define PNX8550_INT_MEM_BASED_SCALAR1  (PNX8550_INT_GIC_MIN+27)
-#define PNX8550_INT_VIDEO_MPEG         (PNX8550_INT_GIC_MIN+28)
-#define PNX8550_INT_VIDEO_INPUT_P1     (PNX8550_INT_GIC_MIN+29)
-
-#define PNX8550_INT_VIDEO_INPUT_P2     (PNX8550_INT_GIC_MIN+30)
-#define PNX8550_INT_SPDI1              (PNX8550_INT_GIC_MIN+31)
-#define PNX8550_INT_SPDO               (PNX8550_INT_GIC_MIN+32)
-#define PNX8550_INT_AUDIO_INPUT1       (PNX8550_INT_GIC_MIN+33)
-#define PNX8550_INT_AUDIO_OUTPUT1      (PNX8550_INT_GIC_MIN+34)
-#define PNX8550_INT_AUDIO_INPUT2       (PNX8550_INT_GIC_MIN+35)
-#define PNX8550_INT_AUDIO_OUTPUT2      (PNX8550_INT_GIC_MIN+36)
-#define PNX8550_INT_MEMBASED_SCALAR2   (PNX8550_INT_GIC_MIN+37)
-#define PNX8550_INT_VPK                (PNX8550_INT_GIC_MIN+38)
-#define PNX8550_INT_MPEG1_MIPS         (PNX8550_INT_GIC_MIN+39)
-
-#define PNX8550_INT_MPEG1_TM           (PNX8550_INT_GIC_MIN+40)
-#define PNX8550_INT_MPEG2_MIPS         (PNX8550_INT_GIC_MIN+41)
-#define PNX8550_INT_MPEG2_TM           (PNX8550_INT_GIC_MIN+42)
-#define PNX8550_INT_TS_DMA             (PNX8550_INT_GIC_MIN+43)
-#define PNX8550_INT_EDMA               (PNX8550_INT_GIC_MIN+44)
-#define PNX8550_INT_TM_DEBUG1          (PNX8550_INT_GIC_MIN+45)
-#define PNX8550_INT_TM_DEBUG2          (PNX8550_INT_GIC_MIN+46)
-#define PNX8550_INT_PCI_INTA           (PNX8550_INT_GIC_MIN+47)
-#define PNX8550_INT_CLOCK_MODULE       (PNX8550_INT_GIC_MIN+48)
-#define PNX8550_INT_PCI_XIO_INTA_PCI   (PNX8550_INT_GIC_MIN+49)
-
-#define PNX8550_INT_PCI_XIO_INTB_DMA   (PNX8550_INT_GIC_MIN+50)
-#define PNX8550_INT_PCI_XIO_INTC_GPPM  (PNX8550_INT_GIC_MIN+51)
-#define PNX8550_INT_PCI_XIO_INTD_GPXIO (PNX8550_INT_GIC_MIN+52)
-#define PNX8550_INT_DVD_CSS            (PNX8550_INT_GIC_MIN+53)
-#define PNX8550_INT_VLD                (PNX8550_INT_GIC_MIN+54)
-#define PNX8550_INT_GPIO_TSU_7_0       (PNX8550_INT_GIC_MIN+55)
-#define PNX8550_INT_GPIO_TSU_15_8      (PNX8550_INT_GIC_MIN+56)
-#define PNX8550_INT_GPIO_CTU_IR        (PNX8550_INT_GIC_MIN+57)
-#define PNX8550_INT_GPIO0              (PNX8550_INT_GIC_MIN+58)
-#define PNX8550_INT_GPIO1              (PNX8550_INT_GIC_MIN+59)
-
-#define PNX8550_INT_GPIO2              (PNX8550_INT_GIC_MIN+60)
-#define PNX8550_INT_GPIO3              (PNX8550_INT_GIC_MIN+61)
-#define PNX8550_INT_GPIO4              (PNX8550_INT_GIC_MIN+62)
-#define PNX8550_INT_GPIO5              (PNX8550_INT_GIC_MIN+63)
-#define PNX8550_INT_GPIO6              (PNX8550_INT_GIC_MIN+64)
-#define PNX8550_INT_GPIO7              (PNX8550_INT_GIC_MIN+65)
-#define PNX8550_INT_PMAN_SECURITY      (PNX8550_INT_GIC_MIN+66)
-#define PNX8550_INT_I2C3               (PNX8550_INT_GIC_MIN+67)
-#define PNX8550_INT_RESERVED_68        (PNX8550_INT_GIC_MIN+68)
-#define PNX8550_INT_SPDI2              (PNX8550_INT_GIC_MIN+69)
-
-#define PNX8550_INT_I2C4               (PNX8550_INT_GIC_MIN+70)
-
-// Timer are 3 exceptions connected to cp0's 7th hardware exception
-#define PNX8550_INT_TIMER_TOTINT       3
-#define PNX8550_INT_TIMER_MIN	       (PNX8550_INT_GIC_MAX+1)
-#define PNX8550_INT_TIMER_MAX          (PNX8550_INT_TIMER_MIN + PNX8550_INT_TIMER_TOTINT - 1)
-
-#define PNX8550_INT_TIMER1             (PNX8550_INT_TIMER_MIN+0)
-#define PNX8550_INT_TIMER2             (PNX8550_INT_TIMER_MIN+1)
-#define PNX8550_INT_TIMER3             (PNX8550_INT_TIMER_MIN+2)
-#define PNX8550_INT_WATCHDOG           PNX8550_INT_TIMER3
-
-#endif

arch/mips/include/asm/mach-pnx8550/kernel-entry-init.h

@@ -1,262 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2005 Embedded Alley Solutions, Inc
- */
-#ifndef __ASM_MACH_KERNEL_ENTRY_INIT_H
-#define __ASM_MACH_KERNEL_ENTRY_INIT_H
-
-#include <asm/cacheops.h>
-#include <asm/addrspace.h>
-
-#define CO_CONFIGPR_VALID  0x3F1F41FF    /* valid bits to write to ConfigPR */
-#define HAZARD_CP0 nop; nop; nop; nop; nop; nop; nop; nop; nop; nop; nop; nop;
-#define CACHE_OPC      0xBC000000  /* MIPS cache instruction opcode */
-#define ICACHE_LINE_SIZE        32      /* Instruction cache line size bytes */
-#define DCACHE_LINE_SIZE        32      /* Data cache line size in bytes */
-
-#define ICACHE_SET_COUNT        256     /* Instruction cache set count */
-#define DCACHE_SET_COUNT        128     /* Data cache set count */
-
-#define ICACHE_SET_SIZE         (ICACHE_SET_COUNT * ICACHE_LINE_SIZE)
-#define DCACHE_SET_SIZE         (DCACHE_SET_COUNT * DCACHE_LINE_SIZE)
-
-	.macro	kernel_entry_setup
-	.set	push
-	.set	noreorder
-	/*
-	 * PNX8550 entry point, when running a non compressed
-	 * kernel. When loading a zImage, the head.S code in
-	 * arch/mips/zboot/pnx8550 will init the caches and,
-	 * decompress the kernel, and branch to kernel_entry.
-		 */
-cache_begin:	li	t0, (1<<28)
-	mtc0	t0, CP0_STATUS /* cp0 usable */
-	HAZARD_CP0
-
-	mtc0 	zero, CP0_CAUSE
-	HAZARD_CP0
-
-
-	/* Set static virtual to phys address translation and TLB disabled */
-	mfc0 	t0, CP0_CONFIG, 7
-	HAZARD_CP0
-
-	and	t0, ~((1<<19) | (1<<20))     /* TLB/MAP cleared */
-	mtc0	t0, CP0_CONFIG, 7
-	HAZARD_CP0
-
-	/* CPU boots with kseg0 cache algo set to 0x2 -- uncached */
-
-	init_icache
-	nop
-	init_dcache
-	nop
-
-	cachePr4450ICReset
-	nop
-
-	cachePr4450DCReset
-	nop
-
-	/* read ConfigPR into t0 */
-	mfc0	t0, CP0_CONFIG, 7
-	HAZARD_CP0
-
-	/*  enable the TLB */
-	or      t0, (1<<19)
-
-	/* disable the ICACHE: at least 10x slower */
-	/* or      t0, (1<<26) */
-
-	/* disable the DCACHE; CONFIG_CPU_HAS_LLSC should not be set  */
-	/* or      t0, (1<<27) */
-
-	and	t0, CO_CONFIGPR_VALID
-
-	/* enable TLB. */
-	mtc0	t0, CP0_CONFIG, 7
-	HAZARD_CP0
-cache_end:
-	/* Setup CMEM_0 to MMIO address space, 2MB */
-	lui    t0, 0x1BE0
-	addi   t0, t0, 0x3
-	mtc0   $8, $22, 4
-	nop
-
-	/* Setup CMEM_1, 128MB */
-	lui    t0, 0x1000
-	addi   t0, t0, 0xf
-	mtc0   $8, $22, 5
-	nop
-
-
-	/* Setup CMEM_2, 32MB */
-	lui    t0, 0x1C00
-	addi   t0, t0, 0xb
-	mtc0   $8, $22, 6
-	nop
-
-	/* Setup CMEM_3, 0MB */
-	lui    t0, 0x0
-	addi   t0, t0, 0x0
-	mtc0   $8, $22, 7
-	nop
-
-	/* Enable cache */
-	mfc0	t0, CP0_CONFIG
-	HAZARD_CP0
-	and	t0, t0, 0xFFFFFFF8
-	or	t0, t0, 3
-	mtc0	t0, CP0_CONFIG
-	HAZARD_CP0
-	.set	pop
-	.endm
-
-	.macro	init_icache
-	.set	push
-	.set	noreorder
-
-	/* Get Cache Configuration */
-	mfc0	t3, CP0_CONFIG, 1
-	HAZARD_CP0
-
-	/* get cache Line size */
-
-	srl   t1, t3, 19   /* C0_CONFIGPR_IL_SHIFT */
-	andi  t1, t1, 0x7  /* C0_CONFIGPR_IL_MASK */
-	beq   t1, zero, pr4450_instr_cache_invalidated /* if zero instruction cache is absent */
-	nop
-	addiu t0, t1, 1
-	ori   t1, zero, 1
-	sllv  t1, t1, t0
-
-	/* get max cache Index */
-	srl   t2, t3, 22  /* C0_CONFIGPR_IS_SHIFT */
-	andi  t2, t2, 0x7 /* C0_CONFIGPR_IS_MASK */
-	addiu t0, t2, 6
-	ori   t2, zero, 1
-	sllv  t2, t2, t0
-
-	/* get max cache way */
-	srl   t3, t3, 16  /* C0_CONFIGPR_IA_SHIFT */
-	andi  t3, t3, 0x7 /* C0_CONFIGPR_IA_MASK */
-	addiu t3, t3, 1
-
-	/* total no of cache lines */
-	multu t2, t3             /* max index * max way */
-	mflo  t2
-	addiu t2, t2, -1
-
-	move  t0, zero
-pr4450_next_instruction_cache_set:
-	cache  Index_Invalidate_I, 0(t0)
-	addu  t0, t0, t1         /* add bytes in a line */
-	bne   t2, zero, pr4450_next_instruction_cache_set
-	addiu t2, t2, -1   /* reduce no of lines to invalidate by one */
-pr4450_instr_cache_invalidated:
-	.set	pop
-	.endm
-
-	.macro	init_dcache
-	.set	push
-	.set	noreorder
-	move t1, zero
-
-	/* Store Tag Information */
-	mtc0	zero, CP0_TAGLO, 0
-	HAZARD_CP0
-
-	mtc0	zero, CP0_TAGHI, 0
-	HAZARD_CP0
-
-	/* Cache size is 16384 = 512 lines x 32 bytes per line */
-	or       t2, zero, (128*4)-1  /* 512 lines  */
-	/* Invalidate all lines */
-2:
-	cache Index_Store_Tag_D, 0(t1)
-	addiu    t2, t2, -1
-	bne      t2, zero, 2b
-	addiu    t1, t1, 32        /* 32 bytes in a line */
-	.set pop
-	.endm
-
-	.macro	cachePr4450ICReset
-	.set	push
-	.set	noreorder
-
-	/* Save CP0 status reg on entry; */
-	/* disable interrupts during cache reset */
-	mfc0    t0, CP0_STATUS      /* T0 = interrupt status on entry */
-	HAZARD_CP0
-
-	mtc0    zero, CP0_STATUS   /* disable CPU interrupts */
-	HAZARD_CP0
-
-	or      t1, zero, zero              /* T1 = starting cache index (0) */
-	ori     t2, zero, (256 - 1) /* T2 = inst cache set cnt - 1 */
-
-	icache_invd_loop:
-	/* 9 == register t1 */
-	.word   CACHE_OPC | (9 << 21) | (Index_Invalidate_I << 16) | \
-		(0 * ICACHE_SET_SIZE)  /* invalidate inst cache WAY0 */
-	.word   CACHE_OPC | (9 << 21) | (Index_Invalidate_I << 16) | \
-		(1 * ICACHE_SET_SIZE)  /* invalidate inst cache WAY1 */
-
-	addiu   t1, t1, ICACHE_LINE_SIZE    /* T1 = next cache line index */
-	bne     t2, zero, icache_invd_loop /* T2 = 0 if all sets invalidated */
-	addiu   t2, t2, -1        /* decrement T2 set cnt (delay slot) */
-
-	/* Initialize the latches in the instruction cache tag */
-	/* that drive the way selection tri-state bus drivers, by doing a */
-	/* dummy load while the instruction cache is still disabled. */
-	/* TODO: Is this needed ? */
-	la      t1, KSEG0            /* T1 = cached memory base address */
-	lw      zero, 0x0000(t1)      /* (dummy read of first memory word) */
-
-	mtc0    t0, CP0_STATUS        /* restore interrupt status on entry */
-	HAZARD_CP0
-	.set	pop
-	.endm
-
-	.macro	cachePr4450DCReset
-	.set	push
-	.set	noreorder
-	mfc0    t0, CP0_STATUS           /* T0 = interrupt status on entry */
-	HAZARD_CP0
-	mtc0    zero, CP0_STATUS         /* disable CPU interrupts */
-	HAZARD_CP0
-
-	/* Writeback/invalidate entire data cache sets/ways/lines */
-	or      t1, zero, zero              /* T1 = starting cache index (0) */
-	ori     t2, zero, (DCACHE_SET_COUNT - 1) /* T2 = data cache set cnt - 1 */
-
-	dcache_wbinvd_loop:
-	/* 9 == register t1 */
-	.word   CACHE_OPC | (9 << 21) | (Index_Writeback_Inv_D << 16) | \
-		(0 * DCACHE_SET_SIZE)  /* writeback/invalidate WAY0 */
-	.word   CACHE_OPC | (9 << 21) | (Index_Writeback_Inv_D << 16) | \
-		(1 * DCACHE_SET_SIZE)  /* writeback/invalidate WAY1 */
-	.word   CACHE_OPC | (9 << 21) | (Index_Writeback_Inv_D << 16) | \
-		(2 * DCACHE_SET_SIZE)  /* writeback/invalidate WAY2 */
-	.word   CACHE_OPC | (9 << 21) | (Index_Writeback_Inv_D << 16) | \
-		(3 * DCACHE_SET_SIZE)  /* writeback/invalidate WAY3 */
-
-	addiu   t1, t1, DCACHE_LINE_SIZE  /* T1 = next data cache line index */
-	bne     t2, zero, dcache_wbinvd_loop /* T2 = 0 when wbinvd entire cache */
-	addiu   t2, t2, -1          /* decrement T2 set cnt (delay slot) */
-
-	/* Initialize the latches in the data cache tag that drive the way
-	selection tri-state bus drivers, by doing a dummy load while the
-	data cache is still in the disabled mode.  TODO: Is this needed ? */
-	la      t1, KSEG0            /* T1 = cached memory base address */
-	lw      zero, 0x0000(t1)      /* (dummy read of first memory word) */
-
-	mtc0    t0, CP0_STATUS       /* restore interrupt status on entry */
-	HAZARD_CP0
-	.set	pop
-	.endm
-
-#endif /* __ASM_MACH_KERNEL_ENTRY_INIT_H */

arch/mips/include/asm/mach-pnx8550/nand.h

@@ -1,121 +0,0 @@
-#ifndef __PNX8550_NAND_H
-#define __PNX8550_NAND_H
-
-#define PNX8550_NAND_BASE_ADDR   0x10000000
-#define PNX8550_PCIXIO_BASE	 0xBBE40000
-
-#define PNX8550_DMA_EXT_ADDR     *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x800)
-#define PNX8550_DMA_INT_ADDR     *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x804)
-#define PNX8550_DMA_TRANS_SIZE   *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x808)
-#define PNX8550_DMA_CTRL         *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x80c)
-#define PNX8550_XIO_SEL0         *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x814)
-#define PNX8550_GPXIO_ADDR       *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x820)
-#define PNX8550_GPXIO_WR         *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x824)
-#define PNX8550_GPXIO_RD         *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x828)
-#define PNX8550_GPXIO_CTRL       *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x82C)
-#define PNX8550_XIO_FLASH_CTRL   *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0x830)
-#define PNX8550_GPXIO_INT_STATUS *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0xfb0)
-#define PNX8550_GPXIO_INT_ENABLE *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0xfb4)
-#define PNX8550_GPXIO_INT_CLEAR  *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0xfb8)
-#define PNX8550_DMA_INT_STATUS   *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0xfd0)
-#define PNX8550_DMA_INT_ENABLE   *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0xfd4)
-#define PNX8550_DMA_INT_CLEAR    *(volatile unsigned long *)(PNX8550_PCIXIO_BASE + 0xfd8)
-
-#define PNX8550_XIO_SEL0_EN_16BIT    0x00800000
-#define PNX8550_XIO_SEL0_USE_ACK     0x00400000
-#define PNX8550_XIO_SEL0_REN_HIGH    0x00100000
-#define PNX8550_XIO_SEL0_REN_LOW     0x00040000
-#define PNX8550_XIO_SEL0_WEN_HIGH    0x00010000
-#define PNX8550_XIO_SEL0_WEN_LOW     0x00004000
-#define PNX8550_XIO_SEL0_WAIT        0x00000200
-#define PNX8550_XIO_SEL0_OFFSET      0x00000020
-#define PNX8550_XIO_SEL0_TYPE_68360  0x00000000
-#define PNX8550_XIO_SEL0_TYPE_NOR    0x00000008
-#define PNX8550_XIO_SEL0_TYPE_NAND   0x00000010
-#define PNX8550_XIO_SEL0_TYPE_IDE    0x00000018
-#define PNX8550_XIO_SEL0_SIZE_8MB    0x00000000
-#define PNX8550_XIO_SEL0_SIZE_16MB   0x00000002
-#define PNX8550_XIO_SEL0_SIZE_32MB   0x00000004
-#define PNX8550_XIO_SEL0_SIZE_64MB   0x00000006
-#define PNX8550_XIO_SEL0_ENAB        0x00000001
-
-#define PNX8550_SEL0_DEFAULT ((PNX8550_XIO_SEL0_EN_16BIT)  | \
-                              (PNX8550_XIO_SEL0_REN_HIGH*0)| \
-	                      (PNX8550_XIO_SEL0_REN_LOW*2) | \
-	                      (PNX8550_XIO_SEL0_WEN_HIGH*0)| \
-                              (PNX8550_XIO_SEL0_WEN_LOW*2) | \
-	                      (PNX8550_XIO_SEL0_WAIT*4)    | \
-			      (PNX8550_XIO_SEL0_OFFSET*0)  | \
-			      (PNX8550_XIO_SEL0_TYPE_NAND) | \
-			      (PNX8550_XIO_SEL0_SIZE_32MB) | \
-			      (PNX8550_XIO_SEL0_ENAB))
-
-#define PNX8550_GPXIO_PENDING        0x00000200
-#define PNX8550_GPXIO_DONE           0x00000100
-#define PNX8550_GPXIO_CLR_DONE       0x00000080
-#define PNX8550_GPXIO_INIT           0x00000040
-#define PNX8550_GPXIO_READ_CMD       0x00000010
-#define PNX8550_GPXIO_BEN            0x0000000F
-
-#define PNX8550_XIO_FLASH_64MB       0x00200000
-#define PNX8550_XIO_FLASH_INC_DATA   0x00100000
-#define PNX8550_XIO_FLASH_CMD_PH     0x000C0000
-#define PNX8550_XIO_FLASH_CMD_PH2    0x00080000
-#define PNX8550_XIO_FLASH_CMD_PH1    0x00040000
-#define PNX8550_XIO_FLASH_CMD_PH0    0x00000000
-#define PNX8550_XIO_FLASH_ADR_PH     0x00030000
-#define PNX8550_XIO_FLASH_ADR_PH3    0x00030000
-#define PNX8550_XIO_FLASH_ADR_PH2    0x00020000
-#define PNX8550_XIO_FLASH_ADR_PH1    0x00010000
-#define PNX8550_XIO_FLASH_ADR_PH0    0x00000000
-#define PNX8550_XIO_FLASH_CMD_B(x)   ((x<<8) & 0x0000FF00)
-#define PNX8550_XIO_FLASH_CMD_A(x)   (x & 0x000000FF)
-
-#define PNX8550_XIO_INT_ACK          0x00004000
-#define PNX8550_XIO_INT_COMPL        0x00002000
-#define PNX8550_XIO_INT_NONSUP       0x00000200
-#define PNX8550_XIO_INT_ABORT        0x00000004
-
-#define PNX8550_DMA_CTRL_SINGLE_DATA 0x00000400
-#define PNX8550_DMA_CTRL_SND2XIO     0x00000200
-#define PNX8550_DMA_CTRL_FIX_ADDR    0x00000100
-#define PNX8550_DMA_CTRL_BURST_8     0x00000000
-#define PNX8550_DMA_CTRL_BURST_16    0x00000020
-#define PNX8550_DMA_CTRL_BURST_32    0x00000040
-#define PNX8550_DMA_CTRL_BURST_64    0x00000060
-#define PNX8550_DMA_CTRL_BURST_128   0x00000080
-#define PNX8550_DMA_CTRL_BURST_256   0x000000A0
-#define PNX8550_DMA_CTRL_BURST_512   0x000000C0
-#define PNX8550_DMA_CTRL_BURST_NORES 0x000000E0
-#define PNX8550_DMA_CTRL_INIT_DMA    0x00000010
-#define PNX8550_DMA_CTRL_CMD_TYPE    0x0000000F
-
-/* see PCI system arch, page 100 for the full list: */
-#define PNX8550_DMA_CTRL_PCI_CMD_READ    0x00000006
-#define PNX8550_DMA_CTRL_PCI_CMD_WRITE   0x00000007
-
-#define PNX8550_DMA_INT_STAT_ACK_DONE	(1<<14)
-#define PNX8550_DMA_INT_STAT_DMA_DONE	(1<<12)
-#define PNX8550_DMA_INT_STAT_DMA_ERR	(1<<9)
-#define PNX8550_DMA_INT_STAT_PERR5	(1<<5)
-#define PNX8550_DMA_INT_STAT_PERR4	(1<<4)
-#define PNX8550_DMA_INT_STAT_M_ABORT	(1<<2)
-#define PNX8550_DMA_INT_STAT_T_ABORT	(1<<1)
-
-#define PNX8550_DMA_INT_EN_ACK_DONE	(1<<14)
-#define PNX8550_DMA_INT_EN_DMA_DONE	(1<<12)
-#define PNX8550_DMA_INT_EN_DMA_ERR	(1<<9)
-#define PNX8550_DMA_INT_EN_PERR5	(1<<5)
-#define PNX8550_DMA_INT_EN_PERR4	(1<<4)
-#define PNX8550_DMA_INT_EN_M_ABORT	(1<<2)
-#define PNX8550_DMA_INT_EN_T_ABORT	(1<<1)
-
-#define PNX8550_DMA_INT_CLR_ACK_DONE	(1<<14)
-#define PNX8550_DMA_INT_CLR_DMA_DONE	(1<<12)
-#define PNX8550_DMA_INT_CLR_DMA_ERR	(1<<9)
-#define PNX8550_DMA_INT_CLR_PERR5	(1<<5)
-#define PNX8550_DMA_INT_CLR_PERR4	(1<<4)
-#define PNX8550_DMA_INT_CLR_M_ABORT	(1<<2)
-#define PNX8550_DMA_INT_CLR_T_ABORT	(1<<1)
-
-#endif

arch/mips/include/asm/mach-pnx8550/pci.h

@@ -1,185 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * PCI specific definitions
- *
- * Author: source@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-
-#ifndef __PNX8550_PCI_H
-#define __PNX8550_PCI_H
-
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#define PCI_ACCESS_READ  0
-#define PCI_ACCESS_WRITE 1
-
-#define PCI_CMD_IOR                     0x20
-#define PCI_CMD_IOW                     0x30
-#define PCI_CMD_CONFIG_READ             0xa0
-#define PCI_CMD_CONFIG_WRITE            0xb0
-
-#define PCI_IO_TIMEOUT                  1000
-#define PCI_IO_RETRY			5
-/* Timeout for IO and CFG accesses.
-   This is in 1/1024 th of a jiffie(=10ms)
-   i.e. approx 10us */
-#define PCI_IO_JIFFIES_TIMEOUT          40
-#define PCI_IO_JIFFIES_SHIFT            10
-
-#define PCI_BYTE_ENABLE_MASK		0x0000000f
-#define PCI_CFG_BUS_SHIFT               16
-#define PCI_CFG_FUNC_SHIFT              8
-#define PCI_CFG_REG_SHIFT               2
-
-#define PCI_BASE                  0x1be00000
-#define PCI_SETUP                 0x00040010
-#define PCI_DIS_REQGNT           (1<<30)
-#define PCI_DIS_REQGNTA          (1<<29)
-#define PCI_DIS_REQGNTB          (1<<28)
-#define PCI_D2_SUPPORT           (1<<27)
-#define PCI_D1_SUPPORT           (1<<26)
-#define PCI_EN_TA                (1<<24)
-#define PCI_EN_PCI2MMI           (1<<23)
-#define PCI_EN_XIO               (1<<22)
-#define PCI_BASE18_PREF          (1<<21)
-#define SIZE_16M                 0x3
-#define SIZE_32M                 0x4
-#define SIZE_64M                 0x5
-#define SIZE_128M                0x6
-#define PCI_SETUP_BASE18_SIZE(X) (X<<18)
-#define PCI_SETUP_BASE18_EN      (1<<17)
-#define PCI_SETUP_BASE14_PREF    (1<<16)
-#define PCI_SETUP_BASE14_SIZE(X) (X<<12)
-#define PCI_SETUP_BASE14_EN      (1<<11)
-#define PCI_SETUP_BASE10_PREF    (1<<10)
-#define PCI_SETUP_BASE10_SIZE(X) (X<<7)
-#define PCI_SETUP_CFGMANAGE_EN   (1<<1)
-#define PCI_SETUP_PCIARB_EN      (1<<0)
-
-#define PCI_CTRL                  0x040014
-#define PCI_SWPB_DCS_PCI         (1<<16)
-#define PCI_SWPB_PCI_PCI         (1<<15)
-#define PCI_SWPB_PCI_DCS         (1<<14)
-#define PCI_REG_WR_POST          (1<<13)
-#define PCI_XIO_WR_POST          (1<<12)
-#define PCI_PCI2_WR_POST         (1<<13)
-#define PCI_PCI1_WR_POST         (1<<12)
-#define PCI_SERR_SEEN            (1<<11)
-#define PCI_B10_SPEC_RD          (1<<6)
-#define PCI_B14_SPEC_RD          (1<<5)
-#define PCI_B18_SPEC_RD          (1<<4)
-#define PCI_B10_NOSUBWORD        (1<<3)
-#define PCI_B14_NOSUBWORD        (1<<2)
-#define PCI_B18_NOSUBWORD        (1<<1)
-#define PCI_RETRY_TMREN          (1<<0)
-
-#define PCI_BASE1_LO              0x040018
-#define PCI_BASE1_HI              0x04001C
-#define PCI_BASE2_LO              0x040020
-#define PCI_BASE2_HI              0x040024
-#define PCI_RDLIFETIM             0x040028
-#define PCI_GPPM_ADDR             0x04002C
-#define PCI_GPPM_WDAT             0x040030
-#define PCI_GPPM_RDAT             0x040034
-#define PCI_GPPM_CTRL             0x040038
-#define GPPM_DONE                (1<<10)
-#define INIT_PCI_CYCLE           (1<<9)
-#define GPPM_CMD(X)              (((X)&0xf)<<4)
-#define GPPM_BYTEEN(X)           ((X)&0xf)
-#define PCI_UNLOCKREG             0x04003C
-#define UNLOCK_SSID(X)           (((X)&0xff)<<8)
-#define UNLOCK_SETUP(X)          (((X)&0xff)<<0)
-#define UNLOCK_MAGIC             0xCA
-#define PCI_DEV_VEND_ID           0x040040
-#define DEVICE_ID(X)             (((X)>>16)&0xffff)
-#define VENDOR_ID(X)             (((X)&0xffff))
-#define PCI_CFG_CMDSTAT           0x040044
-#define PCI_CFG_STATUS(X)            (((X)>>16)&0xffff)
-#define PCI_CFG_COMMAND(X)           ((X)&0xffff)
-#define PCI_CLASS_REV             0x040048
-#define PCI_CLASSCODE(X)         (((X)>>8)&0xffffff)
-#define PCI_REVID(X)             ((X)&0xff)
-#define PCI_LAT_TMR     0x04004c
-#define PCI_BASE10      0x040050
-#define PCI_BASE14      0x040054
-#define PCI_BASE18      0x040058
-#define PCI_SUBSYS_ID   0x04006c
-#define PCI_CAP_PTR     0x040074
-#define PCI_CFG_MISC    0x04007c
-#define PCI_PMC         0x040080
-#define PCI_PWR_STATE   0x040084
-#define PCI_IO          0x040088
-#define PCI_SLVTUNING   0x04008C
-#define PCI_DMATUNING   0x040090
-#define PCI_DMAEADDR    0x040800
-#define PCI_DMAIADDR    0x040804
-#define PCI_DMALEN      0x040808
-#define PCI_DMACTRL     0x04080C
-#define PCI_XIOCTRL     0x040810
-#define PCI_SEL0PROF    0x040814
-#define PCI_SEL1PROF    0x040818
-#define PCI_SEL2PROF    0x04081C
-#define PCI_GPXIOADDR   0x040820
-#define PCI_NANDCTRLS   0x400830
-#define PCI_SEL3PROF    0x040834
-#define PCI_SEL4PROF    0x040838
-#define PCI_GPXIO_STAT  0x040FB0
-#define PCI_GPXIO_IMASK 0x040FB4
-#define PCI_GPXIO_ICLR  0x040FB8
-#define PCI_GPXIO_ISET  0x040FBC
-#define PCI_GPPM_STATUS 0x040FC0
-#define GPPM_DONE      (1<<10)
-#define GPPM_ERR       (1<<9)
-#define GPPM_MPAR_ERR  (1<<8)
-#define GPPM_PAR_ERR   (1<<7)
-#define GPPM_R_MABORT  (1<<2)
-#define GPPM_R_TABORT  (1<<1)
-#define PCI_GPPM_IMASK  0x040FC4
-#define PCI_GPPM_ICLR   0x040FC8
-#define PCI_GPPM_ISET   0x040FCC
-#define PCI_DMA_STATUS  0x040FD0
-#define PCI_DMA_IMASK   0x040FD4
-#define PCI_DMA_ICLR    0x040FD8
-#define PCI_DMA_ISET    0x040FDC
-#define PCI_ISTATUS     0x040FE0
-#define PCI_IMASK       0x040FE4
-#define PCI_ICLR        0x040FE8
-#define PCI_ISET        0x040FEC
-#define PCI_MOD_ID      0x040FFC
-
-/*
- *  PCI configuration cycle AD bus definition
- */
-/* Type 0 */
-#define PCI_CFG_TYPE0_REG_SHF           0
-#define PCI_CFG_TYPE0_FUNC_SHF          8
-
-/* Type 1 */
-#define PCI_CFG_TYPE1_REG_SHF           0
-#define PCI_CFG_TYPE1_FUNC_SHF          8
-#define PCI_CFG_TYPE1_DEV_SHF           11
-#define PCI_CFG_TYPE1_BUS_SHF           16
-
-/*
- *  Ethernet device DP83816 definition
- */
-#define DP83816_IRQ_ETHER               66
-
-#endif

arch/mips/include/asm/mach-pnx8550/uart.h

@@ -1,30 +0,0 @@
-#ifndef __IP3106_UART_H
-#define __IP3106_UART_H
-
-#include <int.h>
-
-/* early macros for kgdb use. fixme: clean this up */
-
-#define UART_BASE		0xbbe4a000	/* PNX8550 */
-
-#define PNX8550_UART_PORT0	(UART_BASE)
-#define PNX8550_UART_PORT1	(UART_BASE + 0x1000)
-
-#define PNX8550_UART_INT(x)		(PNX8550_INT_GIC_MIN+19+x)
-#define IRQ_TO_UART(x)			(x-PNX8550_INT_GIC_MIN-19)
-
-/* early macros needed for prom/kgdb */
-
-#define ip3106_lcr(base, port)    *(volatile u32 *)(base+(port*0x1000) + 0x000)
-#define ip3106_mcr(base, port)   *(volatile u32 *)(base+(port*0x1000) + 0x004)
-#define ip3106_baud(base, port)  *(volatile u32 *)(base+(port*0x1000) + 0x008)
-#define ip3106_cfg(base, port)   *(volatile u32 *)(base+(port*0x1000) + 0x00C)
-#define ip3106_fifo(base, port)	 *(volatile u32 *)(base+(port*0x1000) + 0x028)
-#define ip3106_istat(base, port) *(volatile u32 *)(base+(port*0x1000) + 0xFE0)
-#define ip3106_ien(base, port)   *(volatile u32 *)(base+(port*0x1000) + 0xFE4)
-#define ip3106_iclr(base, port)  *(volatile u32 *)(base+(port*0x1000) + 0xFE8)
-#define ip3106_iset(base, port)  *(volatile u32 *)(base+(port*0x1000) + 0xFEC)
-#define ip3106_pd(base, port)    *(volatile u32 *)(base+(port*0x1000) + 0xFF4)
-#define ip3106_mid(base, port)   *(volatile u32 *)(base+(port*0x1000) + 0xFFC)
-
-#endif

arch/mips/include/asm/mach-pnx8550/usb.h

@@ -1,32 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *  USB specific definitions
- *
- * Author: source@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-
-#ifndef __PNX8550_USB_H
-#define __PNX8550_USB_H
-
-/*
- * USB Host controller
- */
-
-#define PNX8550_USB_OHCI_OP_BASE	0x1be48000
-#define PNX8550_USB_OHCI_OP_LEN	        0x1000
-
-#endif

arch/mips/include/asm/mach-pnx8550/war.h

@@ -1,24 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <ralf@linux-mips.org>
- */
-#ifndef __ASM_MIPS_MACH_PNX8550_WAR_H
-#define __ASM_MIPS_MACH_PNX8550_WAR_H
-
-#define R4600_V1_INDEX_ICACHEOP_WAR	0
-#define R4600_V1_HIT_CACHEOP_WAR	0
-#define R4600_V2_HIT_CACHEOP_WAR	0
-#define R5432_CP0_INTERRUPT_WAR		0
-#define BCM1250_M3_WAR			0
-#define SIBYTE_1956_WAR			0
-#define MIPS4K_ICACHE_REFILL_WAR	0
-#define MIPS_CACHE_SYNC_WAR		0
-#define TX49XX_ICACHE_INDEX_INV_WAR	0
-#define ICACHE_REFILLS_WORKAROUND_WAR	0
-#define R10000_LLSC_WAR			0
-#define MIPS34K_MISSED_ITLB_WAR		0
-
-#endif /* __ASM_MIPS_MACH_PNX8550_WAR_H */

arch/mips/pci/Makefile

@@ -27,7 +27,6 @@ obj-$(CONFIG_PCI_AR724X)	+= pci-ar724x.o
 #
 obj-$(CONFIG_LASAT)		+= pci-lasat.o
 obj-$(CONFIG_MIPS_COBALT)	+= fixup-cobalt.o
-obj-$(CONFIG_SOC_PNX8550)	+= fixup-pnx8550.o ops-pnx8550.o
 obj-$(CONFIG_LEMOTE_FULOONG2E)	+= fixup-fuloong2e.o ops-loongson2.o
 obj-$(CONFIG_LEMOTE_MACH2F)	+= fixup-lemote2f.o ops-loongson2.o
 obj-$(CONFIG_MIPS_MALTA)	+= fixup-malta.o

arch/mips/pci/fixup-pnx8550.c

@@ -1,57 +0,0 @@
-/*
- *  Philips PNX8550 pci fixups.
- *
- *  Copyright 2005 Embedded Alley Solutions, Inc
- *  source@embeddealley.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <asm/mach-pnx8550/pci.h>
-#include <asm/mach-pnx8550/int.h>
-
-
-#undef	DEBUG
-#ifdef 	DEBUG
-#define	DBG(x...)	printk(x)
-#else
-#define	DBG(x...)
-#endif
-
-extern char pnx8550_irq_tab[][5];
-
-void __init pcibios_fixup_resources(struct pci_dev *dev)
-{
-	/* no need to fixup IO resources */
-}
-
-void __init pcibios_fixup(void)
-{
-	/* nothing to do here */
-}
-
-int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	return pnx8550_irq_tab[slot][pin];
-}
-
-/* Do platform specific device initialization at pci_enable_device() time */
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
-	return 0;
-}

arch/mips/pci/ops-pnx8550.c

@@ -1,282 +0,0 @@
-/*
- *
- *  BRIEF MODULE DESCRIPTION
- *
- *  2.6 port, Embedded Alley Solutions, Inc
- *
- *  Based on:
- *  Author: source@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/vmalloc.h>
-#include <linux/delay.h>
-
-#include <asm/mach-pnx8550/pci.h>
-#include <asm/mach-pnx8550/glb.h>
-
-static inline void clear_status(void)
-{
-	unsigned long pci_stat;
-
-	pci_stat = inl(PCI_BASE | PCI_GPPM_STATUS);
-	outl(pci_stat, PCI_BASE | PCI_GPPM_ICLR);
-}
-
-static inline unsigned int
-calc_cfg_addr(struct pci_bus *bus, unsigned int devfn, int where)
-{
-	unsigned int addr;
-
-	addr = ((bus->number > 0) ? (((bus->number & 0xff) << PCI_CFG_BUS_SHIFT) | 1) : 0);
-	addr |= ((devfn & 0xff) << PCI_CFG_FUNC_SHIFT) | (where & 0xfc);
-
-	return addr;
-}
-
-static int
-config_access(unsigned int pci_cmd, struct pci_bus *bus, unsigned int devfn, int where, unsigned int pci_mode, unsigned int *val)
-{
-	unsigned int flags;
-	unsigned long loops = 0;
-	unsigned long ioaddr = calc_cfg_addr(bus, devfn, where);
-
-	local_irq_save(flags);
-	/*Clear pending interrupt status */
-	if (inl(PCI_BASE | PCI_GPPM_STATUS)) {
-		clear_status();
-		while (!(inl(PCI_BASE | PCI_GPPM_STATUS) == 0)) ;
-	}
-
-	outl(ioaddr, PCI_BASE | PCI_GPPM_ADDR);
-
-	if ((pci_cmd == PCI_CMD_IOW) || (pci_cmd == PCI_CMD_CONFIG_WRITE))
-		outl(*val, PCI_BASE | PCI_GPPM_WDAT);
-
-	outl(INIT_PCI_CYCLE | pci_cmd | (pci_mode & PCI_BYTE_ENABLE_MASK),
-	     PCI_BASE | PCI_GPPM_CTRL);
-
-	loops =
-	    ((loops_per_jiffy *
-	      PCI_IO_JIFFIES_TIMEOUT) >> (PCI_IO_JIFFIES_SHIFT));
-	while (1) {
-		if (inl(PCI_BASE | PCI_GPPM_STATUS) & GPPM_DONE) {
-			if ((pci_cmd == PCI_CMD_IOR) ||
-			    (pci_cmd == PCI_CMD_CONFIG_READ))
-				*val = inl(PCI_BASE | PCI_GPPM_RDAT);
-			clear_status();
-			local_irq_restore(flags);
-			return PCIBIOS_SUCCESSFUL;
-		} else if (inl(PCI_BASE | PCI_GPPM_STATUS) & GPPM_R_MABORT) {
-			break;
-		}
-
-		loops--;
-		if (loops == 0) {
-			printk("%s : Arbiter Locked.\n", __func__);
-		}
-	}
-
-	clear_status();
-	if ((pci_cmd == PCI_CMD_IOR) || (pci_cmd == PCI_CMD_IOW)) {
-		printk("%s timeout (GPPM_CTRL=%X) ioaddr %lX pci_cmd %X\n",
-		       __func__, inl(PCI_BASE | PCI_GPPM_CTRL), ioaddr,
-		       pci_cmd);
-	}
-
-	if ((pci_cmd == PCI_CMD_IOR) || (pci_cmd == PCI_CMD_CONFIG_READ))
-		*val = 0xffffffff;
-	local_irq_restore(flags);
-	return PCIBIOS_DEVICE_NOT_FOUND;
-}
-
-/*
- * We can't address 8 and 16 bit words directly.  Instead we have to
- * read/write a 32bit word and mask/modify the data we actually want.
- */
-static int
-read_config_byte(struct pci_bus *bus, unsigned int devfn, int where, u8 * val)
-{
-	unsigned int data = 0;
-	int err;
-
-	if (bus == NULL)
-		return -1;
-
-	err = config_access(PCI_CMD_CONFIG_READ, bus, devfn, where, ~(1 << (where & 3)), &data);
-	switch (where & 0x03) {
-	case 0:
-		*val = (unsigned char)(data & 0x000000ff);
-		break;
-	case 1:
-		*val = (unsigned char)((data & 0x0000ff00) >> 8);
-		break;
-	case 2:
-		*val = (unsigned char)((data & 0x00ff0000) >> 16);
-		break;
-	case 3:
-		*val = (unsigned char)((data & 0xff000000) >> 24);
-		break;
-	}
-
-	return err;
-}
-
-static int
-read_config_word(struct pci_bus *bus, unsigned int devfn, int where, u16 * val)
-{
-	unsigned int data = 0;
-	int err;
-
-	if (bus == NULL)
-		return -1;
-
-	if (where & 0x01)
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-
-	err = config_access(PCI_CMD_CONFIG_READ, bus, devfn, where, ~(3 << (where & 3)), &data);
-	switch (where & 0x02) {
-	case 0:
-		*val = (unsigned short)(data & 0x0000ffff);
-		break;
-	case 2:
-		*val = (unsigned short)((data & 0xffff0000) >> 16);
-		break;
-	}
-
-	return err;
-}
-
-static int
-read_config_dword(struct pci_bus *bus, unsigned int devfn, int where, u32 * val)
-{
-	int err;
-	if (bus == NULL)
-		return -1;
-
-	if (where & 0x03)
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-
-	err = config_access(PCI_CMD_CONFIG_READ, bus, devfn, where, 0, val);
-
-	return err;
-}
-
-static int
-write_config_byte(struct pci_bus *bus, unsigned int devfn, int where, u8 val)
-{
-	unsigned int data = (unsigned int)val;
-	int err;
-
-	if (bus == NULL)
-		return -1;
-
-	switch (where & 0x03) {
-	case 1:
-		data = (data << 8);
-		break;
-	case 2:
-		data = (data << 16);
-		break;
-	case 3:
-		data = (data << 24);
-		break;
-	default:
-		break;
-	}
-
-	err = config_access(PCI_CMD_CONFIG_WRITE, bus, devfn, where, ~(1 << (where & 3)), &data);
-
-	return err;
-}
-
-static int
-write_config_word(struct pci_bus *bus, unsigned int devfn, int where, u16 val)
-{
-	unsigned int data = (unsigned int)val;
-	int err;
-
-	if (bus == NULL)
-		return -1;
-
-	if (where & 0x01)
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-
-	switch (where & 0x02) {
-	case 2:
-		data = (data << 16);
-		break;
-	default:
-		break;
-	}
-	err = config_access(PCI_CMD_CONFIG_WRITE, bus, devfn, where, ~(3 << (where & 3)), &data);
-
-	return err;
-}
-
-static int
-write_config_dword(struct pci_bus *bus, unsigned int devfn, int where, u32 val)
-{
-	int err;
-	if (bus == NULL)
-		return -1;
-
-	if (where & 0x03)
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-
-	err = config_access(PCI_CMD_CONFIG_WRITE, bus, devfn, where, 0, &val);
-
-	return err;
-}
-
-static int config_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 * val)
-{
-	switch (size) {
-	case 1: {
-			u8 _val;
-			int rc = read_config_byte(bus, devfn, where, &_val);
-			*val = _val;
-			return rc;
-		}
-       case 2: {
-			u16 _val;
-			int rc = read_config_word(bus, devfn, where, &_val);
-			*val = _val;
-			return rc;
-		}
-	default:
-		return read_config_dword(bus, devfn, where, val);
-	}
-}
-
-static int config_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 val)
-{
-	switch (size) {
-	case 1:
-		return write_config_byte(bus, devfn, where, (u8) val);
-	case 2:
-		return write_config_word(bus, devfn, where, (u16) val);
-	default:
-		return write_config_dword(bus, devfn, where, val);
-	}
-}
-
-struct pci_ops pnx8550_pci_ops = {
-	config_read,
-	config_write
-};

arch/mips/pnx8550/Makefile

@@ -1,3 +0,0 @@
-obj-$(CONFIG_SOC_PNX8550)	+= common/
-obj-$(CONFIG_PNX8550_JBS)	+= jbs/
-obj-$(CONFIG_PNX8550_STB810)	+= stb810/

arch/mips/pnx8550/Platform

@@ -1,7 +0,0 @@
-platform-$(CONFIG_SOC_PNX8550)	+= pnx8550/
-
-cflags-$(CONFIG_SOC_PNX8550)	+=					\
-		-I$(srctree)/arch/mips/include/asm/mach-pnx8550
-
-load-$(CONFIG_PNX8550_JBS)	+= 0xffffffff80060000
-load-$(CONFIG_PNX8550_STB810)	+= 0xffffffff80060000

arch/mips/pnx8550/common/Makefile

@@ -1,26 +0,0 @@
-#
-# Per Hallsmark, per.hallsmark@mvista.com
-#
-# ########################################################################
-#
-# This program is free software; you can distribute it and/or modify it
-# under the terms of the GNU General Public License (Version 2) as
-# published by the Free Software Foundation.
-#
-# This program is distributed in the hope it will be useful, but WITHOUT
-# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-# FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
-# for more details.
-#
-# You should have received a copy of the GNU General Public License along
-# with this program; if not, write to the Free Software Foundation, Inc.,
-# 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-#
-# #######################################################################
-#
-# Makefile for the PNX8550 specific kernel interface routines
-# under Linux.
-#
-
-obj-y := setup.o prom.o int.o reset.o time.o proc.o platform.o
-obj-$(CONFIG_PCI) += pci.o

arch/mips/pnx8550/common/int.c

@@ -1,236 +0,0 @@
-/*
- *
- * Copyright (C) 2005 Embedded Alley Solutions, Inc
- * Ported to 2.6.
- *
- * Per Hallsmark, per.hallsmark@mvista.com
- * Copyright (C) 2000, 2001 MIPS Technologies, Inc.
- * Copyright (C) 2001 Ralf Baechle
- *
- * Cleaned up and bug fixing: Pete Popov, ppopov@embeddedalley.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- */
-#include <linux/compiler.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/kernel_stat.h>
-#include <linux/random.h>
-#include <linux/module.h>
-
-#include <asm/io.h>
-#include <int.h>
-#include <uart.h>
-
-/* default prio for interrupts */
-/* first one is a no-no so therefore always prio 0 (disabled) */
-static char gic_prio[PNX8550_INT_GIC_TOTINT] = {
-	0, 1, 1, 1, 1, 15, 1, 1, 1, 1,	//   0 -  9
-	1, 1, 1, 1, 1, 1, 1, 1, 1, 1,	//  10 - 19
-	1, 1, 1, 1, 1, 1, 1, 1, 1, 1,	//  20 - 29
-	1, 1, 1, 1, 1, 1, 1, 1, 1, 1,	//  30 - 39
-	1, 1, 1, 1, 1, 1, 1, 1, 1, 1,	//  40 - 49
-	1, 1, 1, 1, 1, 1, 1, 1, 2, 1,	//  50 - 59
-	1, 1, 1, 1, 1, 1, 1, 1, 1, 1,	//  60 - 69
-	1			//  70
-};
-
-static void hw0_irqdispatch(int irq)
-{
-	/* find out which interrupt */
-	irq = PNX8550_GIC_VECTOR_0 >> 3;
-
-	if (irq == 0) {
-		printk("hw0_irqdispatch: irq 0, spurious interrupt?\n");
-		return;
-	}
-	do_IRQ(PNX8550_INT_GIC_MIN + irq);
-}
-
-
-static void timer_irqdispatch(int irq)
-{
-	irq = (0x01c0 & read_c0_config7()) >> 6;
-
-	if (unlikely(irq == 0)) {
-		printk("timer_irqdispatch: irq 0, spurious interrupt?\n");
-		return;
-	}
-
-	if (irq & 0x1)
-		do_IRQ(PNX8550_INT_TIMER1);
-	if (irq & 0x2)
-		do_IRQ(PNX8550_INT_TIMER2);
-	if (irq & 0x4)
-		do_IRQ(PNX8550_INT_TIMER3);
-}
-
-asmlinkage void plat_irq_dispatch(void)
-{
-	unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
-
-	if (pending & STATUSF_IP2)
-		hw0_irqdispatch(2);
-	else if (pending & STATUSF_IP7) {
-		if (read_c0_config7() & 0x01c0)
-			timer_irqdispatch(7);
-	} else
-		spurious_interrupt();
-}
-
-static inline void modify_cp0_intmask(unsigned clr_mask, unsigned set_mask)
-{
-	unsigned long status = read_c0_status();
-
-	status &= ~((clr_mask & 0xFF) << 8);
-	status |= (set_mask & 0xFF) << 8;
-
-	write_c0_status(status);
-}
-
-static inline void mask_gic_int(unsigned int irq_nr)
-{
-	/* interrupt disabled, bit 26(WE_ENABLE)=1 and bit 16(enable)=0 */
-	PNX8550_GIC_REQ(irq_nr) = 1<<28; /* set priority to 0 */
-}
-
-static inline void unmask_gic_int(unsigned int irq_nr)
-{
-	/* set prio mask to lower four bits and enable interrupt */
-	PNX8550_GIC_REQ(irq_nr) = (1<<26 | 1<<16) | (1<<28) | gic_prio[irq_nr];
-}
-
-static inline void mask_irq(struct irq_data *d)
-{
-	unsigned int irq_nr = d->irq;
-
-	if ((PNX8550_INT_CP0_MIN <= irq_nr) && (irq_nr <= PNX8550_INT_CP0_MAX)) {
-		modify_cp0_intmask(1 << irq_nr, 0);
-	} else if ((PNX8550_INT_GIC_MIN <= irq_nr) &&
-		(irq_nr <= PNX8550_INT_GIC_MAX)) {
-		mask_gic_int(irq_nr - PNX8550_INT_GIC_MIN);
-	} else if ((PNX8550_INT_TIMER_MIN <= irq_nr) &&
-		(irq_nr <= PNX8550_INT_TIMER_MAX)) {
-		modify_cp0_intmask(1 << 7, 0);
-	} else {
-		printk("mask_irq: irq %d doesn't exist!\n", irq_nr);
-	}
-}
-
-static inline void unmask_irq(struct irq_data *d)
-{
-	unsigned int irq_nr = d->irq;
-
-	if ((PNX8550_INT_CP0_MIN <= irq_nr) && (irq_nr <= PNX8550_INT_CP0_MAX)) {
-		modify_cp0_intmask(0, 1 << irq_nr);
-	} else if ((PNX8550_INT_GIC_MIN <= irq_nr) &&
-		(irq_nr <= PNX8550_INT_GIC_MAX)) {
-		unmask_gic_int(irq_nr - PNX8550_INT_GIC_MIN);
-	} else if ((PNX8550_INT_TIMER_MIN <= irq_nr) &&
-		(irq_nr <= PNX8550_INT_TIMER_MAX)) {
-		modify_cp0_intmask(0, 1 << 7);
-	} else {
-		printk("mask_irq: irq %d doesn't exist!\n", irq_nr);
-	}
-}
-
-int pnx8550_set_gic_priority(int irq, int priority)
-{
-	int gic_irq = irq-PNX8550_INT_GIC_MIN;
-	int prev_priority = PNX8550_GIC_REQ(gic_irq) & 0xf;
-
-        gic_prio[gic_irq] = priority;
-	PNX8550_GIC_REQ(gic_irq) |= (0x10000000 | gic_prio[gic_irq]);
-
-	return prev_priority;
-}
-
-static struct irq_chip level_irq_type = {
-	.name =		"PNX Level IRQ",
-	.irq_mask =	mask_irq,
-	.irq_unmask =	unmask_irq,
-};
-
-static struct irqaction gic_action = {
-	.handler =	no_action,
-	.flags =	IRQF_NO_THREAD,
-	.name =		"GIC",
-};
-
-static struct irqaction timer_action = {
-	.handler =	no_action,
-	.flags =	IRQF_TIMER,
-	.name =		"Timer",
-};
-
-void __init arch_init_irq(void)
-{
-	int i;
-	int configPR;
-
-	for (i = 0; i < PNX8550_INT_CP0_TOTINT; i++)
-		irq_set_chip_and_handler(i, &level_irq_type, handle_level_irq);
-
-	/* init of GIC/IPC interrupts */
-	/* should be done before cp0 since cp0 init enables the GIC int */
-	for (i = PNX8550_INT_GIC_MIN; i <= PNX8550_INT_GIC_MAX; i++) {
-		int gic_int_line = i - PNX8550_INT_GIC_MIN;
-		if (gic_int_line == 0 )
-			continue;	// don't fiddle with int 0
-		/*
-		 * enable change of TARGET, ENABLE and ACTIVE_LOW bits
-		 * set TARGET        0 to route through hw0 interrupt
-		 * set ACTIVE_LOW    0 active high  (correct?)
-		 *
-		 * We really should setup an interrupt description table
-		 * to do this nicely.
-		 * Note, PCI INTA is active low on the bus, but inverted
-		 * in the GIC, so to us it's active high.
-		 */
-		PNX8550_GIC_REQ(i - PNX8550_INT_GIC_MIN) = 0x1E000000;
-
-		/* mask/priority is still 0 so we will not get any
-		 * interrupts until it is unmasked */
-
-		irq_set_chip_and_handler(i, &level_irq_type, handle_level_irq);
-	}
-
-	/* Priority level 0 */
-	PNX8550_GIC_PRIMASK_0 = PNX8550_GIC_PRIMASK_1 = 0;
-
-	/* Set int vector table address */
-	PNX8550_GIC_VECTOR_0 = PNX8550_GIC_VECTOR_1 = 0;
-
-	irq_set_chip_and_handler(MIPS_CPU_GIC_IRQ, &level_irq_type,
-				 handle_level_irq);
-	setup_irq(MIPS_CPU_GIC_IRQ, &gic_action);
-
-	/* init of Timer interrupts */
-	for (i = PNX8550_INT_TIMER_MIN; i <= PNX8550_INT_TIMER_MAX; i++)
-		irq_set_chip_and_handler(i, &level_irq_type, handle_level_irq);
-
-	/* Stop Timer 1-3 */
-	configPR = read_c0_config7();
-	configPR |= 0x00000038;
-	write_c0_config7(configPR);
-
-	irq_set_chip_and_handler(MIPS_CPU_TIMER_IRQ, &level_irq_type,
-				 handle_level_irq);
-	setup_irq(MIPS_CPU_TIMER_IRQ, &timer_action);
-}
-
-EXPORT_SYMBOL(pnx8550_set_gic_priority);

arch/mips/pnx8550/common/pci.c

@@ -1,134 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *
- * Author: source@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <pci.h>
-#include <glb.h>
-#include <nand.h>
-
-static struct resource pci_io_resource = {
-	.start	= PNX8550_PCIIO + 0x1000,	/* reserve regacy I/O space */
-	.end	= PNX8550_PCIIO + PNX8550_PCIIO_SIZE,
-	.name	= "pci IO space",
-	.flags	= IORESOURCE_IO
-};
-
-static struct resource pci_mem_resource = {
-	.start	= PNX8550_PCIMEM,
-	.end	= PNX8550_PCIMEM + PNX8550_PCIMEM_SIZE - 1,
-	.name	= "pci memory space",
-	.flags	= IORESOURCE_MEM
-};
-
-extern struct pci_ops pnx8550_pci_ops;
-
-static struct pci_controller pnx8550_controller = {
-	.pci_ops	= &pnx8550_pci_ops,
-	.io_map_base	= PNX8550_PORT_BASE,
-	.io_resource	= &pci_io_resource,
-	.mem_resource	= &pci_mem_resource,
-};
-
-/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
-static inline unsigned long get_system_mem_size(void)
-{
-	/* Read IP2031_RANK0_ADDR_LO */
-	unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
-	/* Read IP2031_RANK1_ADDR_HI */
-	unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
-
-	return dram_r1_hi - dram_r0_lo + 1;
-}
-
-static int __init pnx8550_pci_setup(void)
-{
-	int pci_mem_code;
-	int mem_size = get_system_mem_size() >> 20;
-
-	/* Clear the Global 2 Register, PCI Inta Output Enable Registers
-	   Bit 1:Enable DAC Powerdown
-	  -> 0:DACs are enabled and are working normally
-	     1:DACs are powerdown
-	   Bit 0:Enable of PCI inta output
-	  -> 0 = Disable PCI inta output
-	     1 = Enable PCI inta output
-	*/
-	PNX8550_GLB2_ENAB_INTA_O = 0;
-
-	/* Calc the PCI mem size code */
-	if (mem_size >= 128)
-		pci_mem_code = SIZE_128M;
-	else if (mem_size >= 64)
-		pci_mem_code = SIZE_64M;
-	else if (mem_size >= 32)
-		pci_mem_code = SIZE_32M;
-	else
-		pci_mem_code = SIZE_16M;
-
-	/* Set PCI_XIO registers */
-	outl(pci_mem_resource.start, PCI_BASE | PCI_BASE1_LO);
-	outl(pci_mem_resource.end + 1, PCI_BASE | PCI_BASE1_HI);
-	outl(pci_io_resource.start, PCI_BASE | PCI_BASE2_LO);
-	outl(pci_io_resource.end, PCI_BASE | PCI_BASE2_HI);
-
-	/* Send memory transaction via PCI_BASE2 */
-	outl(0x00000001, PCI_BASE | PCI_IO);
-
-	/* Unlock the setup register */
-	outl(0xca, PCI_BASE | PCI_UNLOCKREG);
-
-	/*
-	 * BAR0 of PNX8550 (pci base 10) must be zero in order for ide
-	 * to work, and in order for bus_to_baddr to work without any
-	 * hacks.
-	 */
-	outl(0x00000000, PCI_BASE | PCI_BASE10);
-
-	/*
-	 *These two bars are set by default or the boot code.
-	 * However, it's safer to set them here so we're not boot
-	 * code dependent.
-	 */
-	outl(0x1be00000, PCI_BASE | PCI_BASE14);  /* PNX MMIO */
-	outl(PNX8550_NAND_BASE_ADDR, PCI_BASE | PCI_BASE18);  /* XIO      */
-
-	outl(PCI_EN_TA |
-	     PCI_EN_PCI2MMI |
-	     PCI_EN_XIO |
-	     PCI_SETUP_BASE18_SIZE(SIZE_32M) |
-	     PCI_SETUP_BASE18_EN |
-	     PCI_SETUP_BASE14_EN |
-	     PCI_SETUP_BASE10_PREF |
-	     PCI_SETUP_BASE10_SIZE(pci_mem_code) |
-	     PCI_SETUP_CFGMANAGE_EN |
-	     PCI_SETUP_PCIARB_EN,
-	     PCI_BASE |
-	     PCI_SETUP);	/* PCI_SETUP */
-	outl(0x00000000, PCI_BASE | PCI_CTRL);	/* PCI_CONTROL */
-
-	register_pci_controller(&pnx8550_controller);
-
-	return 0;
-}
-
-arch_initcall(pnx8550_pci_setup);

arch/mips/pnx8550/common/platform.c

@@ -1,162 +0,0 @@
-/*
- * Platform device support for NXP PNX8550 SoCs
- *
- * Copyright 2005, Embedded Alley Solutions, Inc
- *
- * Based on arch/mips/au1000/common/platform.c
- * Platform device support for Au1x00 SoCs.
- *
- * Copyright 2004, Matt Porter <mporter@kernel.crashing.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <linux/device.h>
-#include <linux/dma-mapping.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/resource.h>
-#include <linux/serial.h>
-#include <linux/serial_pnx8xxx.h>
-#include <linux/platform_device.h>
-#include <linux/usb/ohci_pdriver.h>
-
-#include <int.h>
-#include <usb.h>
-#include <uart.h>
-
-static struct resource pnx8550_usb_ohci_resources[] = {
-	[0] = {
-		.start		= PNX8550_USB_OHCI_OP_BASE,
-		.end		= PNX8550_USB_OHCI_OP_BASE +
-				  PNX8550_USB_OHCI_OP_LEN,
-		.flags		= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start		= PNX8550_INT_USB,
-		.end		= PNX8550_INT_USB,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct resource pnx8550_uart_resources[] = {
-	[0] = {
-		.start		= PNX8550_UART_PORT0,
-		.end		= PNX8550_UART_PORT0 + 0xfff,
-		.flags		= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start		= PNX8550_UART_INT(0),
-		.end		= PNX8550_UART_INT(0),
-		.flags		= IORESOURCE_IRQ,
-	},
-	[2] = {
-		.start		= PNX8550_UART_PORT1,
-		.end		= PNX8550_UART_PORT1 + 0xfff,
-		.flags		= IORESOURCE_MEM,
-	},
-	[3] = {
-		.start		= PNX8550_UART_INT(1),
-		.end		= PNX8550_UART_INT(1),
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-struct pnx8xxx_port pnx8xxx_ports[] = {
-	[0] = {
-		.port   = {
-			.type		= PORT_PNX8XXX,
-			.iotype		= UPIO_MEM,
-			.membase	= (void __iomem *)PNX8550_UART_PORT0,
-			.mapbase	= PNX8550_UART_PORT0,
-			.irq		= PNX8550_UART_INT(0),
-			.uartclk	= 3692300,
-			.fifosize	= 16,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 0,
-		},
-	},
-	[1] = {
-		.port   = {
-			.type		= PORT_PNX8XXX,
-			.iotype		= UPIO_MEM,
-			.membase	= (void __iomem *)PNX8550_UART_PORT1,
-			.mapbase	= PNX8550_UART_PORT1,
-			.irq		= PNX8550_UART_INT(1),
-			.uartclk	= 3692300,
-			.fifosize	= 16,
-			.flags		= UPF_BOOT_AUTOCONF,
-			.line		= 1,
-		},
-	},
-};
-
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-
-static u64 uart_dmamask = DMA_BIT_MASK(32);
-
-static int pnx8550_usb_ohci_power_on(struct platform_device *pdev)
-{
-	/*
-	 * Set register CLK48CTL to enable and 48MHz
-	 */
-	outl(0x00000003, PCI_BASE | 0x0004770c);
-
-	/*
-	 * Set register CLK12CTL to enable and 48MHz
-	 */
-	outl(0x00000003, PCI_BASE | 0x00047710);
-
-	udelay(100);
-
-	return 0;
-}
-
-static void pnx8550_usb_ohci_power_off(struct platform_device *pdev)
-{
-	udelay(10);
-}
-
-static struct usb_ohci_pdata pnx8550_usb_ohci_pdata = {
-	.power_on	= pnx8550_usb_ohci_power_on,
-	.power_off	= pnx8550_usb_ohci_power_off,
-};
-
-static struct platform_device pnx8550_usb_ohci_device = {
-	.name		= "ohci-platform",
-	.id		= -1,
-	.dev = {
-		.dma_mask		= &ohci_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data		= &pnx8550_usb_ohci_pdata,
-	},
-	.num_resources	= ARRAY_SIZE(pnx8550_usb_ohci_resources),
-	.resource	= pnx8550_usb_ohci_resources,
-};
-
-static struct platform_device pnx8550_uart_device = {
-	.name		= "pnx8xxx-uart",
-	.id		= -1,
-	.dev = {
-		.dma_mask		= &uart_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data = pnx8xxx_ports,
-	},
-	.num_resources	= ARRAY_SIZE(pnx8550_uart_resources),
-	.resource	= pnx8550_uart_resources,
-};
-
-static struct platform_device *pnx8550_platform_devices[] __initdata = {
-	&pnx8550_usb_ohci_device,
-	&pnx8550_uart_device,
-};
-
-static int __init pnx8550_platform_init(void)
-{
-	return platform_add_devices(pnx8550_platform_devices,
-			            ARRAY_SIZE(pnx8550_platform_devices));
-}
-
-arch_initcall(pnx8550_platform_init);

arch/mips/pnx8550/common/proc.c

@@ -1,110 +0,0 @@
-/*
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/init.h>
-#include <linux/proc_fs.h>
-#include <linux/irq.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/kernel_stat.h>
-#include <linux/random.h>
-
-#include <asm/io.h>
-#include <int.h>
-#include <uart.h>
-
-
-static int pnx8550_timers_read(char* page, char** start, off_t offset, int count, int* eof, void* data)
-{
-        int len = 0;
-	int configPR = read_c0_config7();
-
-        if (offset==0) {
-		len += sprintf(&page[len], "Timer:       count,  compare, tc, status\n");
-                len += sprintf(&page[len], "    1: %11i, %8i,  %1i, %s\n",
-			       read_c0_count(), read_c0_compare(),
-			      (configPR>>6)&0x1, ((configPR>>3)&0x1)? "off":"on");
-                len += sprintf(&page[len], "    2: %11i, %8i,  %1i, %s\n",
-			       read_c0_count2(), read_c0_compare2(),
-			      (configPR>>7)&0x1, ((configPR>>4)&0x1)? "off":"on");
-                len += sprintf(&page[len], "    3: %11i, %8i,  %1i, %s\n",
-			       read_c0_count3(), read_c0_compare3(),
-			      (configPR>>8)&0x1, ((configPR>>5)&0x1)? "off":"on");
-        }
-
-        return len;
-}
-
-static int pnx8550_registers_read(char* page, char** start, off_t offset, int count, int* eof, void* data)
-{
-        int len = 0;
-
-        if (offset==0) {
-                len += sprintf(&page[len], "config1:   %#10.8x\n", read_c0_config1());
-                len += sprintf(&page[len], "config2:   %#10.8x\n", read_c0_config2());
-                len += sprintf(&page[len], "config3:   %#10.8x\n", read_c0_config3());
-                len += sprintf(&page[len], "configPR:  %#10.8x\n", read_c0_config7());
-                len += sprintf(&page[len], "status:    %#10.8x\n", read_c0_status());
-                len += sprintf(&page[len], "cause:     %#10.8x\n", read_c0_cause());
-                len += sprintf(&page[len], "count:     %#10.8x\n", read_c0_count());
-                len += sprintf(&page[len], "count_2:   %#10.8x\n", read_c0_count2());
-                len += sprintf(&page[len], "count_3:   %#10.8x\n", read_c0_count3());
-                len += sprintf(&page[len], "compare:   %#10.8x\n", read_c0_compare());
-                len += sprintf(&page[len], "compare_2: %#10.8x\n", read_c0_compare2());
-                len += sprintf(&page[len], "compare_3: %#10.8x\n", read_c0_compare3());
-        }
-
-        return len;
-}
-
-static struct proc_dir_entry* pnx8550_dir;
-static struct proc_dir_entry* pnx8550_timers;
-static struct proc_dir_entry* pnx8550_registers;
-
-static int pnx8550_proc_init( void )
-{
-
-	// Create /proc/pnx8550
-        pnx8550_dir = proc_mkdir("pnx8550", NULL);
-        if (!pnx8550_dir) {
-                printk(KERN_ERR "Can't create pnx8550 proc dir\n");
-                return -1;
-        }
-
-	// Create /proc/pnx8550/timers
-        pnx8550_timers = create_proc_read_entry(
-		"timers",
-		0,
-		pnx8550_dir,
-		pnx8550_timers_read,
-		NULL);
-
-        if (!pnx8550_timers)
-                printk(KERN_ERR "Can't create pnx8550 timers proc file\n");
-
-	// Create /proc/pnx8550/registers
-        pnx8550_registers = create_proc_read_entry(
-		"registers",
-		0,
-		pnx8550_dir,
-		pnx8550_registers_read,
-		NULL);
-
-        if (!pnx8550_registers)
-                printk(KERN_ERR "Can't create pnx8550 registers proc file\n");
-
-	return 0;
-}
-
-__initcall(pnx8550_proc_init);

arch/mips/pnx8550/common/prom.c

@@ -1,128 +0,0 @@
-/*
- *
- * Per Hallsmark, per.hallsmark@mvista.com
- *
- * Based on jmr3927/common/prom.c
- *
- * 2004 (c) MontaVista Software, Inc. This file is licensed under the
- * terms of the GNU General Public License version 2. This program is
- * licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/serial_pnx8xxx.h>
-
-#include <asm/bootinfo.h>
-#include <uart.h>
-
-/* #define DEBUG_CMDLINE */
-
-extern int prom_argc;
-extern char **prom_argv, **prom_envp;
-
-typedef struct
-{
-    char *name;
-/*    char *val; */
-}t_env_var;
-
-
-char * __init prom_getcmdline(void)
-{
-	return &(arcs_cmdline[0]);
-}
-
-void __init prom_init_cmdline(void)
-{
-	int i;
-
-	arcs_cmdline[0] = '\0';
-	for (i = 0; i < prom_argc; i++) {
-		strcat(arcs_cmdline, prom_argv[i]);
-		strcat(arcs_cmdline, " ");
-	}
-}
-
-char *prom_getenv(char *envname)
-{
-	/*
-	 * Return a pointer to the given environment variable.
-	 * Environment variables are stored in the form of "memsize=64".
-	 */
-
-	t_env_var *env = (t_env_var *)prom_envp;
-	int i;
-
-	i = strlen(envname);
-
-	while(env->name) {
-		if(strncmp(envname, env->name, i) == 0) {
-			return(env->name + strlen(envname) + 1);
-		}
-		env++;
-	}
-	return(NULL);
-}
-
-inline unsigned char str2hexnum(unsigned char c)
-{
-	if(c >= '0' && c <= '9')
-		return c - '0';
-	if(c >= 'a' && c <= 'f')
-		return c - 'a' + 10;
-	if(c >= 'A' && c <= 'F')
-		return c - 'A' + 10;
-	return 0; /* foo */
-}
-
-inline void str2eaddr(unsigned char *ea, unsigned char *str)
-{
-	int i;
-
-	for(i = 0; i < 6; i++) {
-		unsigned char num;
-
-		if((*str == '.') || (*str == ':'))
-			str++;
-		num = str2hexnum(*str++) << 4;
-		num |= (str2hexnum(*str++));
-		ea[i] = num;
-	}
-}
-
-int get_ethernet_addr(char *ethernet_addr)
-{
-        char *ethaddr_str;
-
-        ethaddr_str = prom_getenv("ethaddr");
-	if (!ethaddr_str) {
-	        printk("ethaddr not set in boot prom\n");
-		return -1;
-	}
-	str2eaddr(ethernet_addr, ethaddr_str);
-	return 0;
-}
-
-void __init prom_free_prom_memory(void)
-{
-}
-
-extern int pnx8550_console_port;
-
-/* used by early printk */
-void prom_putchar(char c)
-{
-	if (pnx8550_console_port != -1) {
-		/* Wait until FIFO not full */
-		while( ((ip3106_fifo(UART_BASE, pnx8550_console_port) & PNX8XXX_UART_FIFO_TXFIFO) >> 16) >= 16)
-			;
-		/* Send one char */
-		ip3106_fifo(UART_BASE, pnx8550_console_port) = c;
-	}
-}
-
-EXPORT_SYMBOL(get_ethernet_addr);
-EXPORT_SYMBOL(str2eaddr);

arch/mips/pnx8550/common/reset.c

@@ -1,40 +0,0 @@
-/*.
- *
- * ########################################################################
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- * Reset the PNX8550 board.
- *
- */
-#include <linux/kernel.h>
-
-#include <asm/processor.h>
-#include <asm/reboot.h>
-#include <glb.h>
-
-void pnx8550_machine_restart(char *command)
-{
-	PNX8550_RST_CTL = PNX8550_RST_DO_SW_RST;
-}
-
-void pnx8550_machine_halt(void)
-{
-	while (1) {
-		if (cpu_wait)
-			cpu_wait();
-	}
-}

arch/mips/pnx8550/common/setup.c

@@ -1,142 +0,0 @@
-/*
- *
- * 2.6 port, Embedded Alley Solutions, Inc
- *
- *  Based on Per Hallsmark, per.hallsmark@mvista.com
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- */
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/ioport.h>
-#include <linux/irq.h>
-#include <linux/mm.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/serial_pnx8xxx.h>
-#include <linux/pm.h>
-
-#include <asm/cpu.h>
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/reboot.h>
-#include <asm/pgtable.h>
-#include <asm/time.h>
-
-#include <glb.h>
-#include <int.h>
-#include <pci.h>
-#include <uart.h>
-#include <nand.h>
-
-extern void __init board_setup(void);
-extern void pnx8550_machine_restart(char *);
-extern void pnx8550_machine_halt(void);
-extern struct resource ioport_resource;
-extern struct resource iomem_resource;
-extern char *prom_getcmdline(void);
-
-struct resource standard_io_resources[] = {
-	{
-		.start	= 0x00,
-		.end	= 0x1f,
-		.name	= "dma1",
-		.flags	= IORESOURCE_BUSY
-	}, {
-		.start	= 0x40,
-		.end	= 0x5f,
-		.name	= "timer",
-		.flags	= IORESOURCE_BUSY
-	}, {
-		.start	= 0x80,
-		.end	= 0x8f,
-		.name	= "dma page reg",
-		.flags	= IORESOURCE_BUSY
-	}, {
-		.start	= 0xc0,
-		.end	= 0xdf,
-		.name	= "dma2",
-		.flags	= IORESOURCE_BUSY
-	},
-};
-
-#define STANDARD_IO_RESOURCES ARRAY_SIZE(standard_io_resources)
-
-extern struct resource pci_io_resource;
-extern struct resource pci_mem_resource;
-
-/* Return the total size of DRAM-memory, (RANK0 + RANK1) */
-unsigned long get_system_mem_size(void)
-{
-	/* Read IP2031_RANK0_ADDR_LO */
-	unsigned long dram_r0_lo = inl(PCI_BASE | 0x65010);
-	/* Read IP2031_RANK1_ADDR_HI */
-	unsigned long dram_r1_hi = inl(PCI_BASE | 0x65018);
-
-	return dram_r1_hi - dram_r0_lo + 1;
-}
-
-int pnx8550_console_port = -1;
-
-void __init plat_mem_setup(void)
-{
-	int i;
-	char* argptr;
-
-	board_setup();  /* board specific setup */
-
-        _machine_restart = pnx8550_machine_restart;
-        _machine_halt = pnx8550_machine_halt;
-        pm_power_off = pnx8550_machine_halt;
-
-	/* Clear the Global 2 Register, PCI Inta Output Enable Registers
-	   Bit 1:Enable DAC Powerdown
-	  -> 0:DACs are enabled and are working normally
-	     1:DACs are powerdown
-	   Bit 0:Enable of PCI inta output
-	  -> 0 = Disable PCI inta output
-	     1 = Enable PCI inta output
-	*/
-	PNX8550_GLB2_ENAB_INTA_O = 0;
-
-	/* IO/MEM resources. */
-	set_io_port_base(PNX8550_PORT_BASE);
-	ioport_resource.start = 0;
-	ioport_resource.end = ~0;
-	iomem_resource.start = 0;
-	iomem_resource.end = ~0;
-
-	/* Request I/O space for devices on this board */
-	for (i = 0; i < STANDARD_IO_RESOURCES; i++)
-		request_resource(&ioport_resource, standard_io_resources + i);
-
-	/* Place the Mode Control bit for GPIO pin 16 in primary function */
-	/* Pin 16 is used by UART1, UA1_TX                                */
-	outl((PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_16_BIT) |
-			(PNX8550_GPIO_MODE_PRIMOP << PNX8550_GPIO_MC_17_BIT),
-			PNX8550_GPIO_MC1);
-
-	argptr = prom_getcmdline();
-	if ((argptr = strstr(argptr, "console=ttyS")) != NULL) {
-		argptr += strlen("console=ttyS");
-		pnx8550_console_port = *argptr == '0' ? 0 : 1;
-
-		/* We must initialize the UART (console) before early printk */
-		/* Set LCR to 8-bit and BAUD to 38400 (no 5)                */
-		ip3106_lcr(UART_BASE, pnx8550_console_port) =
-			PNX8XXX_UART_LCR_8BIT;
-		ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
-	}
-}

arch/mips/pnx8550/common/time.c

@@ -1,151 +0,0 @@
-/*
- * Copyright 2001, 2002, 2003 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
- *
- * Common time service routines for MIPS machines. See
- * Documents/MIPS/README.txt.
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- */
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/param.h>
-#include <linux/time.h>
-#include <linux/timer.h>
-#include <linux/smp.h>
-#include <linux/kernel_stat.h>
-#include <linux/spinlock.h>
-#include <linux/interrupt.h>
-
-#include <asm/bootinfo.h>
-#include <asm/cpu.h>
-#include <asm/time.h>
-#include <asm/hardirq.h>
-#include <asm/div64.h>
-#include <asm/debug.h>
-
-#include <int.h>
-#include <cm.h>
-
-static unsigned long cpj;
-
-static cycle_t hpt_read(struct clocksource *cs)
-{
-	return read_c0_count2();
-}
-
-static struct clocksource pnx_clocksource = {
-	.name		= "pnx8xxx",
-	.rating		= 200,
-	.read		= hpt_read,
-	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
-};
-
-static irqreturn_t pnx8xxx_timer_interrupt(int irq, void *dev_id)
-{
-	struct clock_event_device *c = dev_id;
-
-	/* clear MATCH, signal the event */
-	c->event_handler(c);
-
-	return IRQ_HANDLED;
-}
-
-static struct irqaction pnx8xxx_timer_irq = {
-	.handler	= pnx8xxx_timer_interrupt,
-	.flags		= IRQF_PERCPU | IRQF_TIMER,
-	.name		= "pnx8xxx_timer",
-};
-
-static irqreturn_t monotonic_interrupt(int irq, void *dev_id)
-{
-	/* Timer 2 clear interrupt */
-	write_c0_compare2(-1);
-	return IRQ_HANDLED;
-}
-
-static struct irqaction monotonic_irqaction = {
-	.handler = monotonic_interrupt,
-	.flags = IRQF_TIMER,
-	.name = "Monotonic timer",
-};
-
-static int pnx8xxx_set_next_event(unsigned long delta,
-				struct clock_event_device *evt)
-{
-	write_c0_compare(delta);
-	return 0;
-}
-
-static struct clock_event_device pnx8xxx_clockevent = {
-	.name		= "pnx8xxx_clockevent",
-	.features	= CLOCK_EVT_FEAT_ONESHOT,
-	.set_next_event = pnx8xxx_set_next_event,
-};
-
-static inline void timer_ack(void)
-{
-	write_c0_compare(cpj);
-}
-
-__init void plat_time_init(void)
-{
-	unsigned int configPR;
-	unsigned int n;
-	unsigned int m;
-	unsigned int p;
-	unsigned int pow2p;
-
-	pnx8xxx_clockevent.cpumask = cpu_none_mask;
-	clockevents_register_device(&pnx8xxx_clockevent);
-	clocksource_register(&pnx_clocksource);
-
-	/* Timer 1 start */
-	configPR = read_c0_config7();
-	configPR &= ~0x00000008;
-	write_c0_config7(configPR);
-
-	/* Timer 2 start */
-	configPR = read_c0_config7();
-	configPR &= ~0x00000010;
-	write_c0_config7(configPR);
-
-	/* Timer 3 stop */
-	configPR = read_c0_config7();
-	configPR |= 0x00000020;
-	write_c0_config7(configPR);
-
-
-        /* PLL0 sets MIPS clock (PLL1 <=> TM1, PLL6 <=> TM2, PLL5 <=> mem) */
-        /* (but only if CLK_MIPS_CTL select value [bits 3:1] is 1:  FIXME) */
-
-        n = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_N_MASK) >> 16;
-        m = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_M_MASK) >> 8;
-        p = (PNX8550_CM_PLL0_CTL & PNX8550_CM_PLL_P_MASK) >> 2;
-	pow2p = (1 << p);
-
-	db_assert(m != 0 && pow2p != 0);
-
-        /*
-	 * Compute the frequency as in the PNX8550 User Manual 1.0, p.186
-	 * (a.k.a. 8-10).  Divide by HZ for a timer offset that results in
-	 * HZ timer interrupts per second.
-	 */
-	mips_hpt_frequency = 27UL * ((1000000UL * n)/(m * pow2p));
-	cpj = DIV_ROUND_CLOSEST(mips_hpt_frequency, HZ);
-	write_c0_count(0);
-	timer_ack();
-
-	/* Setup Timer 2 */
-	write_c0_count2(0);
-	write_c0_compare2(0xffffffff);
-
-	setup_irq(PNX8550_INT_TIMER1, &pnx8xxx_timer_irq);
-	setup_irq(PNX8550_INT_TIMER2, &monotonic_irqaction);
-}

arch/mips/pnx8550/jbs/Makefile

@@ -1,4 +0,0 @@
-
-# Makefile for the NXP JBS Board.
-
-obj-y := init.o board_setup.o irqmap.o

arch/mips/pnx8550/jbs/board_setup.c

@@ -1,56 +0,0 @@
-/*
- *  JBS Specific board startup routines.
- *
- *  Copyright 2005, Embedded Alley Solutions, Inc
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/ioport.h>
-#include <linux/mm.h>
-#include <linux/console.h>
-#include <linux/mc146818rtc.h>
-#include <linux/delay.h>
-
-#include <asm/cpu.h>
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/reboot.h>
-#include <asm/pgtable.h>
-
-#include <glb.h>
-
-/* CP0 hazard avoidance. */
-#define BARRIER __asm__ __volatile__(".set noreorder\n\t" \
-				     "nop; nop; nop; nop; nop; nop;\n\t" \
-				     ".set reorder\n\t")
-
-void __init board_setup(void)
-{
-	unsigned long configpr;
-
-	configpr = read_c0_config7();
-	configpr |= (1<<19); /* enable tlb */
-	write_c0_config7(configpr);
-	BARRIER;
-}

arch/mips/pnx8550/jbs/init.c

@@ -1,53 +0,0 @@
-/*
- *
- *  Copyright 2005 Embedded Alley Solutions, Inc
- *  source@embeddedalley.com
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-
-int prom_argc;
-char **prom_argv, **prom_envp;
-extern void  __init prom_init_cmdline(void);
-extern char *prom_getenv(char *envname);
-
-const char *get_system_type(void)
-{
-	return "NXP PNX8550/JBS";
-}
-
-void __init prom_init(void)
-{
-	unsigned long memsize;
-
-	//memsize = 0x02800000; /* Trimedia uses memory above */
-	memsize = 0x08000000; /* Trimedia uses memory above */
-	add_memory_region(0, memsize, BOOT_MEM_RAM);
-}

arch/mips/pnx8550/jbs/irqmap.c

@@ -1,35 +0,0 @@
-/*
- *  NXP JBS board irqmap.
- *
- *  Copyright 2005 Embedded Alley Solutions, Inc
- *  source@embeddealley.com
- *
- *  This program is free software; you can redistribute	 it and/or modify it
- *  under  the terms of	 the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the	License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
- *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
- *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <int.h>
-
-char pnx8550_irq_tab[][5] __initdata = {
-	[8]	= { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-	[9]	= { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-	[17]	= { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-};

arch/mips/pnx8550/stb810/Makefile

@@ -1,4 +0,0 @@
-
-# Makefile for the NXP STB810 Board.
-
-obj-y := prom_init.o board_setup.o irqmap.o

arch/mips/pnx8550/stb810/board_setup.c

@@ -1,41 +0,0 @@
-/*
- *  STB810 specific board startup routines.
- *
- *  Based on the arch/mips/nxp/pnx8550/jbs/board_setup.c
- *
- *  Author: MontaVista Software, Inc.
- *          source@mvista.com
- *
- *  Copyright 2005 MontaVista Software Inc.
- *
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License as published by the
- *  Free Software Foundation; either version 2 of the License, or (at your
- *  option) any later version.
- */
-
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/ioport.h>
-#include <linux/mm.h>
-#include <linux/console.h>
-#include <linux/mc146818rtc.h>
-#include <linux/delay.h>
-
-#include <asm/cpu.h>
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/reboot.h>
-#include <asm/pgtable.h>
-
-#include <glb.h>
-
-void __init board_setup(void)
-{
-	unsigned long configpr;
-
-	configpr = read_c0_config7();
-	configpr |= (1<<19); /* enable tlb */
-	write_c0_config7(configpr);
-}

arch/mips/pnx8550/stb810/irqmap.c

@@ -1,22 +0,0 @@
-/*
- *  NXP STB810 board irqmap.
- *
- *  Author: MontaVista Software, Inc.
- *          source@mvista.com
- *
- *  Copyright 2005 MontaVista Software Inc.
- *
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License as published by the
- *  Free Software Foundation; either version 2 of the License, or (at your
- *  option) any later version.
- */
-
-#include <linux/init.h>
-#include <int.h>
-
-char pnx8550_irq_tab[][5] __initdata = {
-	[8]	= { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-	[9]	= { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-	[10]	= { -1, PNX8550_INT_PCI_INTA, 0xff, 0xff, 0xff},
-};

arch/mips/pnx8550/stb810/prom_init.c

@@ -1,46 +0,0 @@
-/*
- *  STB810 specific prom routines
- *
- *  Author: MontaVista Software, Inc.
- *          source@mvista.com
- *
- *  Copyright 2005 MontaVista Software Inc.
- *
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License as published by the
- *  Free Software Foundation; either version 2 of the License, or (at your
- *  option) any later version.
- */
-
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-
-int prom_argc;
-char **prom_argv, **prom_envp;
-extern void  __init prom_init_cmdline(void);
-extern char *prom_getenv(char *envname);
-
-const char *get_system_type(void)
-{
-	return "NXP PNX8950/STB810";
-}
-
-void __init prom_init(void)
-{
-	unsigned long memsize;
-
-	prom_argc = (int) fw_arg0;
-	prom_argv = (char **) fw_arg1;
-	prom_envp = (char **) fw_arg2;
-
-	prom_init_cmdline();
-
-	memsize = 0x08000000; /* Trimedia uses memory above */
-	add_memory_region(0, memsize, BOOT_MEM_RAM);
-}

drivers/tty/serial/Kconfig

@@ -716,19 +716,19 @@ config SERIAL_SH_SCI_DMA
 
 config SERIAL_PNX8XXX
 	bool "Enable PNX8XXX SoCs' UART Support"
-	depends on SOC_PNX8550 || SOC_PNX833X
+	depends on SOC_PNX833X
 	select SERIAL_CORE
 	help
-	  If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
-	  and you want to use serial ports, say Y.  Otherwise, say N.
+	  If you have a MIPS-based Philips SoC such as PNX8330 and you want
+	  to use serial ports, say Y.  Otherwise, say N.
 
 config SERIAL_PNX8XXX_CONSOLE
 	bool "Enable PNX8XX0 serial console"
 	depends on SERIAL_PNX8XXX
 	select SERIAL_CORE_CONSOLE
 	help
-	  If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
-	  and you want to use serial console, say Y. Otherwise, say N.
+	  If you have a MIPS-based Philips SoC such as PNX8330 and you want
+	  to use serial console, say Y. Otherwise, say N.
 
 config SERIAL_HS_LPC32XX
 	tristate "LPC32XX high speed serial port support"