[PATCH] sk98lin: error handling on dual port board

Sk98lin driver error recovery on two port boards is bad.
If it fails the second allocation, it will not release resources
properly. Also it registers the second port in the pci driver data

If second port fails, might as well go with one port.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

drivers/net/sk98lin/skge.c

@@ -4899,15 +4899,17 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
 
 	boards_found++;
 
+	pci_set_drvdata(pdev, dev);
+
 	/* More then one port found */
 	if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) {
-		if ((dev = alloc_etherdev(sizeof(DEV_NET))) == 0) {
-			printk(KERN_ERR "Unable to allocate etherdev "
+		dev = alloc_etherdev(sizeof(DEV_NET));
+		if (!dev) {
+			printk(KERN_ERR "sk98lin: unable to allocate etherdev "
 				"structure!\n");
-			goto out;
+			goto single_port;
 		}
 
-		pAC->dev[1]   = dev;
 		pNet          = netdev_priv(dev);
 		pNet->PortNr  = 1;
 		pNet->NetNr   = 1;
@@ -4939,20 +4941,25 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
 		if (using_dac)
 			dev->features |= NETIF_F_HIGHDMA;
 
-		if (register_netdev(dev)) {
-			printk(KERN_ERR "sk98lin: Could not register device for seconf port.\n");
+		error = register_netdev(dev);
+		if (error) {
+			printk(KERN_ERR "sk98lin: Could not register device"
+			       " for second port. (%d)\n", error);
 			free_netdev(dev);
-			pAC->dev[1] = pAC->dev[0];
-		} else {
-			memcpy(&dev->dev_addr,
-					&pAC->Addr.Net[1].CurrentMacAddress, 6);
-			memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
-	
-			printk("%s: %s\n", dev->name, DeviceStr);
-			printk("      PrefPort:B  RlmtMode:Dual Check Link State\n");
+			goto single_port;
 		}
+
+		pAC->dev[1]   = dev;
+		memcpy(&dev->dev_addr,
+		       &pAC->Addr.Net[1].CurrentMacAddress, 6);
+		memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
+
+		printk("%s: %s\n", dev->name, DeviceStr);
+		printk("      PrefPort:B  RlmtMode:Dual Check Link State\n");
 	}
 
+single_port:
+
 	/* Save the hardware revision */
 	pAC->HWRevision = (((pAC->GIni.GIPciHwRev >> 4) & 0x0F)*10) +
 		(pAC->GIni.GIPciHwRev & 0x0F);
@@ -4964,7 +4971,6 @@ static int __devinit skge_probe_one(struct pci_dev *pdev,
 	memset(&pAC->PnmiBackup, 0, sizeof(SK_PNMI_STRUCT_DATA));
 	memcpy(&pAC->PnmiBackup, &pAC->PnmiStruct, sizeof(SK_PNMI_STRUCT_DATA));
 
-	pci_set_drvdata(pdev, dev);
 	return 0;
 
  out_free_resources: