Merge upstream kernel into libata 'passthru' branch

CREDITS

@@ -2423,8 +2423,7 @@ S: Toronto, Ontario
 S: Canada
 
 N: Zwane Mwaikambo
-E: zwane@linuxpower.ca
-W: http://function.linuxpower.ca
+E: zwane@arm.linux.org.uk
 D: Various driver hacking
 D: Lowlevel x86 kernel hacking
 D: General debugging

Documentation/acpi-hotkey.txt

@@ -33,3 +33,6 @@ The result of the execution of this aml method is
 attached to /proc/acpi/hotkey/poll_method, which is dnyamically
 created.  Please use command "cat /proc/acpi/hotkey/polling_method" 
 to retrieve it.
+
+Note: Use cmdline "acpi_generic_hotkey" to over-ride
+loading any platform specific drivers.

Documentation/arm/Samsung-S3C24XX/USB-Host.txt

@@ -0,0 +1,93 @@
+			S3C24XX USB Host support
+			========================
+
+
+
+Introduction
+------------
+
+  This document details the S3C2410/S3C2440 in-built OHCI USB host support.
+
+Configuration
+-------------
+
+  Enable at least the following kernel options:
+
+  menuconfig:
+
+   Device Drivers  --->
+     USB support  --->
+       <*> Support for Host-side USB
+       <*>   OHCI HCD support
+
+
+  .config:
+    CONFIG_USB
+    CONFIG_USB_OHCI_HCD
+
+
+  Once these options are configured, the standard set of USB device
+  drivers can be configured and used.
+
+
+Board Support
+-------------
+
+  The driver attaches to a platform device, which will need to be
+  added by the board specific support file in linux/arch/arm/mach-s3c2410,
+  such as mach-bast.c or mach-smdk2410.c
+
+  The platform device's platform_data field is only needed if the
+  board implements extra power control or over-current monitoring.
+
+  The OHCI driver does not ensure the state of the S3C2410's MISCCTRL
+  register, so if both ports are to be used for the host, then it is
+  the board support file's responsibility to ensure that the second
+  port is configured to be connected to the OHCI core.
+
+
+Platform Data
+-------------
+
+  See linux/include/asm-arm/arch-s3c2410/usb-control.h for the
+  descriptions of the platform device data. An implementation
+  can be found in linux/arch/arm/mach-s3c2410/usb-simtec.c .
+
+  The `struct s3c2410_hcd_info` contains a pair of functions
+  that get called to enable over-current detection, and to
+  control the port power status.
+
+  The ports are numbered 0 and 1.
+
+  power_control:
+
+    Called to enable or disable the power on the port.
+
+  enable_oc:
+
+    Called to enable or disable the over-current monitoring.
+    This should claim or release the resources being used to
+    check the power condition on the port, such as an IRQ.
+
+  report_oc:
+
+    The OHCI driver fills this field in for the over-current code
+    to call when there is a change to the over-current state on
+    an port. The ports argument is a bitmask of 1 bit per port,
+    with bit X being 1 for an over-current on port X.
+
+    The function s3c2410_usb_report_oc() has been provided to
+    ensure this is called correctly.
+
+  port[x]:
+
+    This is struct describes each port, 0 or 1. The platform driver
+    should set the flags field of each port to S3C_HCDFLG_USED if
+    the port is enabled.
+
+
+
+Document Author
+---------------
+
+Ben Dooks, (c) 2005 Simtec Electronics

Documentation/kernel-parameters.txt

@@ -159,6 +159,11 @@ running once the system is up.
 
 	acpi_fake_ecdt	[HW,ACPI] Workaround failure due to BIOS lacking ECDT
 
+	acpi_generic_hotkey [HW,ACPI]
+			Allow consolidated generic hotkey driver to
+			over-ride platform specific driver.
+			See also Documentation/acpi-hotkey.txt.
+
 	ad1816=		[HW,OSS]
 			Format: <io>,<irq>,<dma>,<dma2>
 			See also Documentation/sound/oss/AD1816.

Documentation/networking/phy.txt

@@ -0,0 +1,288 @@
+
+-------
+PHY Abstraction Layer
+(Updated 2005-07-21)
+
+Purpose
+
+ Most network devices consist of set of registers which provide an interface
+ to a MAC layer, which communicates with the physical connection through a
+ PHY.  The PHY concerns itself with negotiating link parameters with the link
+ partner on the other side of the network connection (typically, an ethernet
+ cable), and provides a register interface to allow drivers to determine what
+ settings were chosen, and to configure what settings are allowed.
+
+ While these devices are distinct from the network devices, and conform to a
+ standard layout for the registers, it has been common practice to integrate
+ the PHY management code with the network driver.  This has resulted in large
+ amounts of redundant code.  Also, on embedded systems with multiple (and
+ sometimes quite different) ethernet controllers connected to the same 
+ management bus, it is difficult to ensure safe use of the bus.
+
+ Since the PHYs are devices, and the management busses through which they are
+ accessed are, in fact, busses, the PHY Abstraction Layer treats them as such.
+ In doing so, it has these goals:
+
+   1) Increase code-reuse
+   2) Increase overall code-maintainability
+   3) Speed development time for new network drivers, and for new systems
+ 
+ Basically, this layer is meant to provide an interface to PHY devices which
+ allows network driver writers to write as little code as possible, while
+ still providing a full feature set.
+
+The MDIO bus
+
+ Most network devices are connected to a PHY by means of a management bus.
+ Different devices use different busses (though some share common interfaces).
+ In order to take advantage of the PAL, each bus interface needs to be
+ registered as a distinct device.
+
+ 1) read and write functions must be implemented.  Their prototypes are:
+
+     int write(struct mii_bus *bus, int mii_id, int regnum, u16 value);
+     int read(struct mii_bus *bus, int mii_id, int regnum);
+
+   mii_id is the address on the bus for the PHY, and regnum is the register
+   number.  These functions are guaranteed not to be called from interrupt
+   time, so it is safe for them to block, waiting for an interrupt to signal
+   the operation is complete
+ 
+ 2) A reset function is necessary.  This is used to return the bus to an
+   initialized state.
+
+ 3) A probe function is needed.  This function should set up anything the bus
+   driver needs, setup the mii_bus structure, and register with the PAL using
+   mdiobus_register.  Similarly, there's a remove function to undo all of
+   that (use mdiobus_unregister).
+ 
+ 4) Like any driver, the device_driver structure must be configured, and init
+   exit functions are used to register the driver.
+
+ 5) The bus must also be declared somewhere as a device, and registered.
+
+ As an example for how one driver implemented an mdio bus driver, see
+ drivers/net/gianfar_mii.c and arch/ppc/syslib/mpc85xx_devices.c
+
+Connecting to a PHY
+
+ Sometime during startup, the network driver needs to establish a connection
+ between the PHY device, and the network device.  At this time, the PHY's bus
+ and drivers need to all have been loaded, so it is ready for the connection.
+ At this point, there are several ways to connect to the PHY:
+
+ 1) The PAL handles everything, and only calls the network driver when
+   the link state changes, so it can react.
+
+ 2) The PAL handles everything except interrupts (usually because the
+   controller has the interrupt registers).
+
+ 3) The PAL handles everything, but checks in with the driver every second,
+   allowing the network driver to react first to any changes before the PAL
+   does.
+ 
+ 4) The PAL serves only as a library of functions, with the network device
+   manually calling functions to update status, and configure the PHY
+
+
+Letting the PHY Abstraction Layer do Everything
+
+ If you choose option 1 (The hope is that every driver can, but to still be
+ useful to drivers that can't), connecting to the PHY is simple:
+
+ First, you need a function to react to changes in the link state.  This
+ function follows this protocol:
+
+   static void adjust_link(struct net_device *dev);
+ 
+ Next, you need to know the device name of the PHY connected to this device. 
+ The name will look something like, "phy0:0", where the first number is the
+ bus id, and the second is the PHY's address on that bus.
+ 
+ Now, to connect, just call this function:
+ 
+   phydev = phy_connect(dev, phy_name, &adjust_link, flags);
+
+ phydev is a pointer to the phy_device structure which represents the PHY.  If
+ phy_connect is successful, it will return the pointer.  dev, here, is the
+ pointer to your net_device.  Once done, this function will have started the
+ PHY's software state machine, and registered for the PHY's interrupt, if it
+ has one.  The phydev structure will be populated with information about the
+ current state, though the PHY will not yet be truly operational at this
+ point.
+
+ flags is a u32 which can optionally contain phy-specific flags.
+ This is useful if the system has put hardware restrictions on
+ the PHY/controller, of which the PHY needs to be aware.
+
+ Now just make sure that phydev->supported and phydev->advertising have any
+ values pruned from them which don't make sense for your controller (a 10/100
+ controller may be connected to a gigabit capable PHY, so you would need to
+ mask off SUPPORTED_1000baseT*).  See include/linux/ethtool.h for definitions
+ for these bitfields. Note that you should not SET any bits, or the PHY may
+ get put into an unsupported state.
+
+ Lastly, once the controller is ready to handle network traffic, you call
+ phy_start(phydev).  This tells the PAL that you are ready, and configures the
+ PHY to connect to the network.  If you want to handle your own interrupts,
+ just set phydev->irq to PHY_IGNORE_INTERRUPT before you call phy_start.
+ Similarly, if you don't want to use interrupts, set phydev->irq to PHY_POLL.
+
+ When you want to disconnect from the network (even if just briefly), you call
+ phy_stop(phydev).
+
+Keeping Close Tabs on the PAL
+
+ It is possible that the PAL's built-in state machine needs a little help to
+ keep your network device and the PHY properly in sync.  If so, you can
+ register a helper function when connecting to the PHY, which will be called
+ every second before the state machine reacts to any changes.  To do this, you
+ need to manually call phy_attach() and phy_prepare_link(), and then call
+ phy_start_machine() with the second argument set to point to your special
+ handler.
+
+ Currently there are no examples of how to use this functionality, and testing
+ on it has been limited because the author does not have any drivers which use
+ it (they all use option 1).  So Caveat Emptor.
+
+Doing it all yourself
+
+ There's a remote chance that the PAL's built-in state machine cannot track
+ the complex interactions between the PHY and your network device.  If this is
+ so, you can simply call phy_attach(), and not call phy_start_machine or
+ phy_prepare_link().  This will mean that phydev->state is entirely yours to
+ handle (phy_start and phy_stop toggle between some of the states, so you
+ might need to avoid them).
+
+ An effort has been made to make sure that useful functionality can be
+ accessed without the state-machine running, and most of these functions are
+ descended from functions which did not interact with a complex state-machine.
+ However, again, no effort has been made so far to test running without the
+ state machine, so tryer beware.
+
+ Here is a brief rundown of the functions:
+
+ int phy_read(struct phy_device *phydev, u16 regnum);
+ int phy_write(struct phy_device *phydev, u16 regnum, u16 val);
+
+   Simple read/write primitives.  They invoke the bus's read/write function
+   pointers.
+
+ void phy_print_status(struct phy_device *phydev);
+ 
+   A convenience function to print out the PHY status neatly.
+
+ int phy_clear_interrupt(struct phy_device *phydev);
+ int phy_config_interrupt(struct phy_device *phydev, u32 interrupts);
+   
+   Clear the PHY's interrupt, and configure which ones are allowed,
+   respectively.  Currently only supports all on, or all off.
+ 
+ int phy_enable_interrupts(struct phy_device *phydev);
+ int phy_disable_interrupts(struct phy_device *phydev);
+
+   Functions which enable/disable PHY interrupts, clearing them
+   before and after, respectively.
+
+ int phy_start_interrupts(struct phy_device *phydev);
+ int phy_stop_interrupts(struct phy_device *phydev);
+
+   Requests the IRQ for the PHY interrupts, then enables them for
+   start, or disables then frees them for stop.
+
+ struct phy_device * phy_attach(struct net_device *dev, const char *phy_id,
+		 u32 flags);
+
+   Attaches a network device to a particular PHY, binding the PHY to a generic
+   driver if none was found during bus initialization.  Passes in
+   any phy-specific flags as needed.
+
+ int phy_start_aneg(struct phy_device *phydev);
+   
+   Using variables inside the phydev structure, either configures advertising
+   and resets autonegotiation, or disables autonegotiation, and configures
+   forced settings.
+
+ static inline int phy_read_status(struct phy_device *phydev);
+
+   Fills the phydev structure with up-to-date information about the current
+   settings in the PHY.
+
+ void phy_sanitize_settings(struct phy_device *phydev)
+   
+   Resolves differences between currently desired settings, and
+   supported settings for the given PHY device.  Does not make
+   the changes in the hardware, though.
+
+ int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+ int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd);
+
+   Ethtool convenience functions.
+
+ int phy_mii_ioctl(struct phy_device *phydev,
+                 struct mii_ioctl_data *mii_data, int cmd);
+
+   The MII ioctl.  Note that this function will completely screw up the state
+   machine if you write registers like BMCR, BMSR, ADVERTISE, etc.  Best to
+   use this only to write registers which are not standard, and don't set off
+   a renegotiation.
+
+
+PHY Device Drivers
+
+ With the PHY Abstraction Layer, adding support for new PHYs is
+ quite easy.  In some cases, no work is required at all!  However,
+ many PHYs require a little hand-holding to get up-and-running.
+
+Generic PHY driver
+
+ If the desired PHY doesn't have any errata, quirks, or special
+ features you want to support, then it may be best to not add
+ support, and let the PHY Abstraction Layer's Generic PHY Driver
+ do all of the work.  
+
+Writing a PHY driver
+
+ If you do need to write a PHY driver, the first thing to do is
+ make sure it can be matched with an appropriate PHY device.
+ This is done during bus initialization by reading the device's
+ UID (stored in registers 2 and 3), then comparing it to each
+ driver's phy_id field by ANDing it with each driver's
+ phy_id_mask field.  Also, it needs a name.  Here's an example:
+
+   static struct phy_driver dm9161_driver = {
+         .phy_id         = 0x0181b880,
+	 .name           = "Davicom DM9161E",
+	 .phy_id_mask    = 0x0ffffff0,
+	 ...
+   }
+
+ Next, you need to specify what features (speed, duplex, autoneg,
+ etc) your PHY device and driver support.  Most PHYs support
+ PHY_BASIC_FEATURES, but you can look in include/mii.h for other
+ features.
+
+ Each driver consists of a number of function pointers:
+
+   config_init: configures PHY into a sane state after a reset.
+     For instance, a Davicom PHY requires descrambling disabled.
+   probe: Does any setup needed by the driver
+   suspend/resume: power management
+   config_aneg: Changes the speed/duplex/negotiation settings
+   read_status: Reads the current speed/duplex/negotiation settings
+   ack_interrupt: Clear a pending interrupt
+   config_intr: Enable or disable interrupts
+   remove: Does any driver take-down
+
+ Of these, only config_aneg and read_status are required to be
+ assigned by the driver code.  The rest are optional.  Also, it is
+ preferred to use the generic phy driver's versions of these two
+ functions if at all possible: genphy_read_status and
+ genphy_config_aneg.  If this is not possible, it is likely that
+ you only need to perform some actions before and after invoking
+ these functions, and so your functions will wrap the generic
+ ones.
+
+ Feel free to look at the Marvell, Cicada, and Davicom drivers in
+ drivers/net/phy/ for examples (the lxt and qsemi drivers have
+ not been tested as of this writing)

Documentation/pci.txt

@@ -266,20 +266,6 @@ port an old driver to the new PCI interface.  They are no longer present
 in the kernel as they aren't compatible with hotplug or PCI domains or
 having sane locking.
 
-pcibios_present() and		Since ages, you don't need to test presence
-pci_present()			of PCI subsystem when trying to talk to it.
-				If it's not there, the list of PCI devices
-				is empty and all functions for searching for
-				devices just return NULL.
-pcibios_(read|write)_*		Superseded by their pci_(read|write)_*
-				counterparts.
-pcibios_find_*			Superseded by their pci_get_* counterparts.
-pci_for_each_dev()		Superseded by pci_get_device()
-pci_for_each_dev_reverse()	Superseded by pci_find_device_reverse()
-pci_for_each_bus()		Superseded by pci_find_next_bus()
 pci_find_device()		Superseded by pci_get_device()
 pci_find_subsys()		Superseded by pci_get_subsys()
 pci_find_slot()			Superseded by pci_get_slot()
-pcibios_find_class()		Superseded by pci_get_class()
-pci_find_class()		Superseded by pci_get_class()
-pci_(read|write)_*_nodev()	Superseded by pci_bus_(read|write)_*()

MAINTAINERS

@@ -784,7 +784,7 @@ DVB SUBSYSTEM AND DRIVERS
 P:	LinuxTV.org Project
 M: 	linux-dvb-maintainer@linuxtv.org
 L: 	linux-dvb@linuxtv.org (subscription required)
-W:	http://linuxtv.org/developer/dvb.xml
+W:	http://linuxtv.org/
 S:	Supported
 
 EATA-DMA SCSI DRIVER
@@ -1739,7 +1739,7 @@ S:	Maintained
 
 OPL3-SA2, SA3, and SAx DRIVER
 P:	Zwane Mwaikambo
-M:	zwane@commfireservices.com
+M:	zwane@arm.linux.org.uk
 L:	linux-sound@vger.kernel.org
 S:	Maintained
 
@@ -1825,6 +1825,12 @@ P:	Greg Kroah-Hartman
 M:	greg@kroah.com
 S:	Maintained
 
+PCIE HOTPLUG DRIVER
+P:	Kristen Carlson Accardi
+M:	kristen.c.accardi@intel.com
+L:	pcihpd-discuss@lists.sourceforge.net
+S:	Maintained
+
 PCMCIA SUBSYSTEM
 P:	Linux PCMCIA Team
 L:	http://lists.infradead.org/mailman/listinfo/linux-pcmcia
@@ -1989,7 +1995,7 @@ S:	Maintained
 
 SC1200 WDT DRIVER
 P:	Zwane Mwaikambo
-M:	zwane@commfireservices.com
+M:	zwane@arm.linux.org.uk
 S:	Maintained
 
 SCHEDULER
@@ -2201,6 +2207,12 @@ W:	http://projects.buici.com/arm
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 S:	Maintained
 
+SHPC HOTPLUG DRIVER
+P:	Kristen Carlson Accardi
+M:	kristen.c.accardi@intel.com
+L:	pcihpd-discuss@lists.sourceforge.net
+S:	Maintained
+
 SPARC (sparc32):
 P:	William L. Irwin
 M:	wli@holomorphy.com

Makefile

@@ -1,8 +1,8 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 13
-EXTRAVERSION =-rc6
-NAME=Woozy Numbat
+EXTRAVERSION =
+NAME=Affluent Albatross
 
 # *DOCUMENTATION*
 # To see a list of typical targets execute "make help"

arch/alpha/Kconfig

@@ -522,7 +522,7 @@ source "mm/Kconfig"
 
 config NUMA
 	bool "NUMA Support (EXPERIMENTAL)"
-	depends on DISCONTIGMEM
+	depends on DISCONTIGMEM && BROKEN
 	help
 	  Say Y to compile the kernel to support NUMA (Non-Uniform Memory
 	  Access).  This option is for configuring high-end multiprocessor

arch/alpha/kernel/signal.c

@@ -566,13 +566,12 @@ handle_signal(int sig, struct k_sigaction *ka, siginfo_t *info,
 	if (ka->sa.sa_flags & SA_RESETHAND)
 		ka->sa.sa_handler = SIG_DFL;
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER)) 
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 static inline void

arch/alpha/kernel/smp.c

@@ -1036,7 +1036,7 @@ debug_spin_lock(spinlock_t * lock, const char *base_file, int line_no)
 	"	br	1b\n"
 	".previous"
 	: "=r" (tmp), "=m" (lock->lock), "=r" (stuck)
-	: "1" (lock->lock), "2" (stuck) : "memory");
+	: "m" (lock->lock), "2" (stuck) : "memory");
 
 	if (stuck < 0) {
 		printk(KERN_WARNING
@@ -1115,7 +1115,7 @@ void _raw_write_lock(rwlock_t * lock)
 	".previous"
 	: "=m" (*(volatile int *)lock), "=&r" (regx), "=&r" (regy),
 	  "=&r" (stuck_lock), "=&r" (stuck_reader)
-	: "0" (*(volatile int *)lock), "3" (stuck_lock), "4" (stuck_reader) : "memory");
+	: "m" (*(volatile int *)lock), "3" (stuck_lock), "4" (stuck_reader) : "memory");
 
 	if (stuck_lock < 0) {
 		printk(KERN_WARNING "write_lock stuck at %p\n", inline_pc);
@@ -1153,7 +1153,7 @@ void _raw_read_lock(rwlock_t * lock)
 	"	br	1b\n"
 	".previous"
 	: "=m" (*(volatile int *)lock), "=&r" (regx), "=&r" (stuck_lock)
-	: "0" (*(volatile int *)lock), "2" (stuck_lock) : "memory");
+	: "m" (*(volatile int *)lock), "2" (stuck_lock) : "memory");
 
 	if (stuck_lock < 0) {
 		printk(KERN_WARNING "read_lock stuck at %p\n", inline_pc);

arch/alpha/oprofile/common.c

@@ -65,7 +65,7 @@ op_axp_setup(void)
 	model->reg_setup(&reg, ctr, &sys);
 
 	/* Configure the registers on all cpus.  */
-	smp_call_function(model->cpu_setup, &reg, 0, 1);
+	(void)smp_call_function(model->cpu_setup, &reg, 0, 1);
 	model->cpu_setup(&reg);
 	return 0;
 }
@@ -86,7 +86,7 @@ op_axp_cpu_start(void *dummy)
 static int
 op_axp_start(void)
 {
-	smp_call_function(op_axp_cpu_start, NULL, 0, 1);
+	(void)smp_call_function(op_axp_cpu_start, NULL, 0, 1);
 	op_axp_cpu_start(NULL);
 	return 0;
 }
@@ -101,7 +101,7 @@ op_axp_cpu_stop(void *dummy)
 static void
 op_axp_stop(void)
 {
-	smp_call_function(op_axp_cpu_stop, NULL, 0, 1);
+	(void)smp_call_function(op_axp_cpu_stop, NULL, 0, 1);
 	op_axp_cpu_stop(NULL);
 }
 

arch/arm/Kconfig

@@ -310,7 +310,7 @@ menu "Kernel Features"
 
 config SMP
 	bool "Symmetric Multi-Processing (EXPERIMENTAL)"
-	depends on EXPERIMENTAL #&& n
+	depends on EXPERIMENTAL && BROKEN #&& n
 	help
 	  This enables support for systems with more than one CPU. If you have
 	  a system with only one CPU, like most personal computers, say N. If
@@ -635,10 +635,6 @@ config PM
 	  and the Battery Powered Linux mini-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>.
 
-	  Note that, even if you say N here, Linux on the x86 architecture
-	  will issue the hlt instruction if nothing is to be done, thereby
-	  sending the processor to sleep and saving power.
-
 config APM
 	tristate "Advanced Power Management Emulation"
 	depends on PM
@@ -650,12 +646,6 @@ config APM
 	  battery status information, and user-space programs will receive
 	  notification of APM "events" (e.g. battery status change).
 
-	  If you select "Y" here, you can disable actual use of the APM
-	  BIOS by passing the "apm=off" option to the kernel at boot time.
-
-	  Note that the APM support is almost completely disabled for
-	  machines with more than one CPU.
-
 	  In order to use APM, you will need supporting software. For location
 	  and more information, read <file:Documentation/pm.txt> and the
 	  Battery Powered Linux mini-HOWTO, available from
@@ -665,39 +655,12 @@ config APM
 	  manpage ("man 8 hdparm") for that), and it doesn't turn off
 	  VESA-compliant "green" monitors.
 
-	  This driver does not support the TI 4000M TravelMate and the ACER
-	  486/DX4/75 because they don't have compliant BIOSes. Many "green"
-	  desktop machines also don't have compliant BIOSes, and this driver
-	  may cause those machines to panic during the boot phase.
-
 	  Generally, if you don't have a battery in your machine, there isn't
 	  much point in using this driver and you should say N. If you get
 	  random kernel OOPSes or reboots that don't seem to be related to
 	  anything, try disabling/enabling this option (or disabling/enabling
 	  APM in your BIOS).
 
-	  Some other things you should try when experiencing seemingly random,
-	  "weird" problems:
-
-	  1) make sure that you have enough swap space and that it is
-	  enabled.
-	  2) pass the "no-hlt" option to the kernel
-	  3) switch on floating point emulation in the kernel and pass
-	  the "no387" option to the kernel
-	  4) pass the "floppy=nodma" option to the kernel
-	  5) pass the "mem=4M" option to the kernel (thereby disabling
-	  all but the first 4 MB of RAM)
-	  6) make sure that the CPU is not over clocked.
-	  7) read the sig11 FAQ at <http://www.bitwizard.nl/sig11/>
-	  8) disable the cache from your BIOS settings
-	  9) install a fan for the video card or exchange video RAM
-	  10) install a better fan for the CPU
-	  11) exchange RAM chips
-	  12) exchange the motherboard.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called apm.
-
 endmenu
 
 source "net/Kconfig"
@@ -752,6 +715,8 @@ source "drivers/hwmon/Kconfig"
 
 source "drivers/misc/Kconfig"
 
+source "drivers/mfd/Kconfig"
+
 source "drivers/media/Kconfig"
 
 source "drivers/video/Kconfig"

arch/arm/common/Kconfig

@@ -1,6 +1,9 @@
 config ICST525
 	bool
 
+config ARM_GIC
+	bool
+
 config ICST307
 	bool
 

arch/arm/common/Makefile

@@ -4,6 +4,7 @@
 
 obj-y				+= rtctime.o
 obj-$(CONFIG_ARM_AMBA)		+= amba.o
+obj-$(CONFIG_ARM_GIC)		+= gic.o
 obj-$(CONFIG_ICST525)		+= icst525.o
 obj-$(CONFIG_ICST307)		+= icst307.o
 obj-$(CONFIG_SA1111)		+= sa1111.o

arch/arm/common/gic.c

@@ -0,0 +1,166 @@
+/*
+ *  linux/arch/arm/common/gic.c
+ *
+ *  Copyright (C) 2002 ARM Limited, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Interrupt architecture for the GIC:
+ *
+ * o There is one Interrupt Distributor, which receives interrupts
+ *   from system devices and sends them to the Interrupt Controllers.
+ *
+ * o There is one CPU Interface per CPU, which sends interrupts sent
+ *   by the Distributor, and interrupts generated locally, to the
+ *   associated CPU.
+ *
+ * Note that IRQs 0-31 are special - they are local to each CPU.
+ * As such, the enable set/clear, pending set/clear and active bit
+ * registers are banked per-cpu for these sources.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/smp.h>
+
+#include <asm/irq.h>
+#include <asm/io.h>
+#include <asm/mach/irq.h>
+#include <asm/hardware/gic.h>
+
+static void __iomem *gic_dist_base;
+static void __iomem *gic_cpu_base;
+
+/*
+ * Routines to acknowledge, disable and enable interrupts
+ *
+ * Linux assumes that when we're done with an interrupt we need to
+ * unmask it, in the same way we need to unmask an interrupt when
+ * we first enable it.
+ *
+ * The GIC has a seperate notion of "end of interrupt" to re-enable
+ * an interrupt after handling, in order to support hardware
+ * prioritisation.
+ *
+ * We can make the GIC behave in the way that Linux expects by making
+ * our "acknowledge" routine disable the interrupt, then mark it as
+ * complete.
+ */
+static void gic_ack_irq(unsigned int irq)
+{
+	u32 mask = 1 << (irq % 32);
+	writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4);
+	writel(irq, gic_cpu_base + GIC_CPU_EOI);
+}
+
+static void gic_mask_irq(unsigned int irq)
+{
+	u32 mask = 1 << (irq % 32);
+	writel(mask, gic_dist_base + GIC_DIST_ENABLE_CLEAR + (irq / 32) * 4);
+}
+
+static void gic_unmask_irq(unsigned int irq)
+{
+	u32 mask = 1 << (irq % 32);
+	writel(mask, gic_dist_base + GIC_DIST_ENABLE_SET + (irq / 32) * 4);
+}
+
+static void gic_set_cpu(struct irqdesc *desc, unsigned int irq, unsigned int cpu)
+{
+	void __iomem *reg = gic_dist_base + GIC_DIST_TARGET + (irq & ~3);
+	unsigned int shift = (irq % 4) * 8;
+	u32 val;
+
+	val = readl(reg) & ~(0xff << shift);
+	val |= 1 << (cpu + shift);
+	writel(val, reg);
+}
+
+static struct irqchip gic_chip = {
+	.ack		= gic_ack_irq,
+	.mask		= gic_mask_irq,
+	.unmask		= gic_unmask_irq,
+#ifdef CONFIG_SMP
+	.set_cpu	= gic_set_cpu,
+#endif
+};
+
+void __init gic_dist_init(void __iomem *base)
+{
+	unsigned int max_irq, i;
+	u32 cpumask = 1 << smp_processor_id();
+
+	cpumask |= cpumask << 8;
+	cpumask |= cpumask << 16;
+
+	gic_dist_base = base;
+
+	writel(0, base + GIC_DIST_CTRL);
+
+	/*
+	 * Find out how many interrupts are supported.
+	 */
+	max_irq = readl(base + GIC_DIST_CTR) & 0x1f;
+	max_irq = (max_irq + 1) * 32;
+
+	/*
+	 * The GIC only supports up to 1020 interrupt sources.
+	 * Limit this to either the architected maximum, or the
+	 * platform maximum.
+	 */
+	if (max_irq > max(1020, NR_IRQS))
+		max_irq = max(1020, NR_IRQS);
+
+	/*
+	 * Set all global interrupts to be level triggered, active low.
+	 */
+	for (i = 32; i < max_irq; i += 16)
+		writel(0, base + GIC_DIST_CONFIG + i * 4 / 16);
+
+	/*
+	 * Set all global interrupts to this CPU only.
+	 */
+	for (i = 32; i < max_irq; i += 4)
+		writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
+
+	/*
+	 * Set priority on all interrupts.
+	 */
+	for (i = 0; i < max_irq; i += 4)
+		writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4);
+
+	/*
+	 * Disable all interrupts.
+	 */
+	for (i = 0; i < max_irq; i += 32)
+		writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
+
+	/*
+	 * Setup the Linux IRQ subsystem.
+	 */
+	for (i = 29; i < max_irq; i++) {
+		set_irq_chip(i, &gic_chip);
+		set_irq_handler(i, do_level_IRQ);
+		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+	}
+
+	writel(1, base + GIC_DIST_CTRL);
+}
+
+void __cpuinit gic_cpu_init(void __iomem *base)
+{
+	gic_cpu_base = base;
+	writel(0xf0, base + GIC_CPU_PRIMASK);
+	writel(1, base + GIC_CPU_CTRL);
+}
+
+#ifdef CONFIG_SMP
+void gic_raise_softirq(cpumask_t cpumask, unsigned int irq)
+{
+	unsigned long map = *cpus_addr(cpumask);
+
+	writel(map << 16 | irq, gic_dist_base + GIC_DIST_SOFTINT);
+}
+#endif

arch/arm/kernel/calls.S

@@ -327,6 +327,12 @@ __syscall_start:
 /* 310 */	.long	sys_request_key
 		.long	sys_keyctl
 		.long	sys_semtimedop
+/* vserver */	.long	sys_ni_syscall
+		.long	sys_ioprio_set
+/* 315 */	.long	sys_ioprio_get
+		.long	sys_inotify_init
+		.long	sys_inotify_add_watch
+		.long	sys_inotify_rm_watch
 __syscall_end:
 
 		.rept	NR_syscalls - (__syscall_end - __syscall_start) / 4

arch/arm/kernel/entry-armv.S

@@ -533,6 +533,13 @@ ENTRY(__switch_to)
 	ldr	r3, [r2, #TI_TP_VALUE]
 	stmia	ip!, {r4 - sl, fp, sp, lr}	@ Store most regs on stack
 	ldr	r6, [r2, #TI_CPU_DOMAIN]!
+#if __LINUX_ARM_ARCH__ >= 6
+#ifdef CONFIG_CPU_MPCORE
+	clrex
+#else
+	strex	r3, r4, [ip]			@ Clear exclusive monitor
+#endif
+#endif
 #if defined(CONFIG_CPU_XSCALE) && !defined(CONFIG_IWMMXT)
 	mra	r4, r5, acc0
 	stmia   ip, {r4, r5}

arch/arm/kernel/signal.c

@@ -658,11 +658,12 @@ handle_signal(unsigned long sig, struct k_sigaction *ka,
 	/*
 	 * Block the signal if we were unsuccessful.
 	 */
-	if (ret != 0 || !(ka->sa.sa_flags & SA_NODEFER)) {
+	if (ret != 0) {
 		spin_lock_irq(&tsk->sighand->siglock);
 		sigorsets(&tsk->blocked, &tsk->blocked,
 			  &ka->sa.sa_mask);
-		sigaddset(&tsk->blocked, sig);
+		if (!(ka->sa.sa_flags & SA_NODEFER))
+			sigaddset(&tsk->blocked, sig);
 		recalc_sigpending();
 		spin_unlock_irq(&tsk->sighand->siglock);
 	}

arch/arm/kernel/traps.c

@@ -617,7 +617,7 @@ baddataabort(int code, unsigned long instr, struct pt_regs *regs)
 	notify_die("unknown data abort code", regs, &info, instr, 0);
 }
 
-volatile void __bug(const char *file, int line, void *data)
+void __attribute__((noreturn)) __bug(const char *file, int line, void *data)
 {
 	printk(KERN_CRIT"kernel BUG at %s:%d!", file, line);
 	if (data)

arch/arm/lib/bitops.h

@@ -1,4 +1,6 @@
-#if __LINUX_ARM_ARCH__ >= 6
+#include <linux/config.h>
+
+#if __LINUX_ARM_ARCH__ >= 6 && defined(CONFIG_CPU_MPCORE)
 	.macro	bitop, instr
 	mov	r2, #1
 	and	r3, r0, #7		@ Get bit offset

arch/arm/mach-ixp4xx/coyote-setup.c

@@ -36,7 +36,7 @@ static struct flash_platform_data coyote_flash_data = {
 
 static struct resource coyote_flash_resource = {
 	.start		= COYOTE_FLASH_BASE,
-	.end		= COYOTE_FLASH_BASE + COYOTE_FLASH_SIZE,
+	.end		= COYOTE_FLASH_BASE + COYOTE_FLASH_SIZE - 1,
 	.flags		= IORESOURCE_MEM,
 };
 

arch/arm/mach-ixp4xx/gtwx5715-setup.c

@@ -114,7 +114,7 @@ static struct flash_platform_data gtwx5715_flash_data = {
 
 static struct resource gtwx5715_flash_resource = {
 	.start		= GTWX5715_FLASH_BASE,
-	.end		= GTWX5715_FLASH_BASE + GTWX5715_FLASH_SIZE,
+	.end		= GTWX5715_FLASH_BASE + GTWX5715_FLASH_SIZE - 1,
 	.flags		= IORESOURCE_MEM,
 };
 

arch/arm/mach-ixp4xx/ixdp425-setup.c

@@ -36,7 +36,7 @@ static struct flash_platform_data ixdp425_flash_data = {
 
 static struct resource ixdp425_flash_resource = {
 	.start		= IXDP425_FLASH_BASE,
-	.end		= IXDP425_FLASH_BASE + IXDP425_FLASH_SIZE,
+	.end		= IXDP425_FLASH_BASE + IXDP425_FLASH_SIZE - 1,
 	.flags		= IORESOURCE_MEM,
 };
 

arch/arm/mach-s3c2410/s3c2410.c

@@ -18,6 +18,7 @@
  *     28-Sep-2004 BJD  Updates for new serial port bits
  *     04-Nov-2004 BJD  Updated UART configuration process
  *     10-Jan-2005 BJD  Removed s3c2410_clock_tick_rate
+ *     13-Aug-2005 DA   Removed UART from initial I/O mappings
 */
 
 #include <linux/kernel.h>
@@ -49,10 +50,9 @@ static struct map_desc s3c2410_iodesc[] __initdata = {
 	IODESC_ENT(USBHOST),
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(LCD),
-	IODESC_ENT(UART),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(ADC),
-	IODESC_ENT(WATCHDOG)
+	IODESC_ENT(WATCHDOG),
 };
 
 static struct resource s3c_uart0_resource[] = {

arch/arm/mach-s3c2410/usb-simtec.c

@@ -1,6 +1,6 @@
 /* linux/arch/arm/mach-s3c2410/usb-simtec.c
  *
- * Copyright (c) 2004 Simtec Electronics
+ * Copyright (c) 2004,2005 Simtec Electronics
  *   Ben Dooks <ben@simtec.co.uk>
  *
  * http://www.simtec.co.uk/products/EB2410ITX/
@@ -14,6 +14,8 @@
  * Modifications:
  *	14-Sep-2004 BJD  Created
  *	18-Oct-2004 BJD  Cleanups, and added code to report OC cleared
+ *	09-Aug-2005 BJD  Renamed s3c2410_report_oc to s3c2410_usb_report_oc
+ *	09-Aug-2005 BJD  Ports powered only if both are enabled
 */
 
 #define DEBUG
@@ -47,13 +49,19 @@
  * designed boards.
 */
 
+static unsigned int power_state[2];
+
 static void
 usb_simtec_powercontrol(int port, int to)
 {
 	pr_debug("usb_simtec_powercontrol(%d,%d)\n", port, to);
 
-	if (port == 1)
-		s3c2410_gpio_setpin(S3C2410_GPB4, to ? 0:1);
+	power_state[port] = to;
+
+	if (power_state[0] && power_state[1])
+		s3c2410_gpio_setpin(S3C2410_GPB4, 0);
+	else
+		s3c2410_gpio_setpin(S3C2410_GPB4, 1);
 }
 
 static irqreturn_t
@@ -63,10 +71,10 @@ usb_simtec_ocirq(int irq, void *pw, struct pt_regs *regs)
 
 	if (s3c2410_gpio_getpin(S3C2410_GPG10) == 0) {
 		pr_debug("usb_simtec: over-current irq (oc detected)\n");
-		s3c2410_report_oc(info, 3);
+		s3c2410_usb_report_oc(info, 3);
 	} else {
 		pr_debug("usb_simtec: over-current irq (oc cleared)\n");
-		s3c2410_report_oc(info, 0);
+		s3c2410_usb_report_oc(info, 0);
 	}
 
 	return IRQ_HANDLED;

arch/arm/mach-sa1100/assabet.c

@@ -35,6 +35,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/serial_sa1100.h>
 #include <asm/arch/assabet.h>
+#include <asm/arch/mcp.h>
 
 #include "generic.h"
 
@@ -198,6 +199,11 @@ static struct irda_platform_data assabet_irda_data = {
 	.set_speed	= assabet_irda_set_speed,
 };
 
+static struct mcp_plat_data assabet_mcp_data = {
+	.mccr0		= MCCR0_ADM,
+	.sclk_rate	= 11981000,
+};
+
 static void __init assabet_init(void)
 {
 	/*
@@ -246,6 +252,7 @@ static void __init assabet_init(void)
 	sa11x0_set_flash_data(&assabet_flash_data, assabet_flash_resources,
 			      ARRAY_SIZE(assabet_flash_resources));
 	sa11x0_set_irda_data(&assabet_irda_data);
+	sa11x0_set_mcp_data(&assabet_mcp_data);
 }
 
 /*

arch/arm/mach-sa1100/cerf.c

@@ -29,6 +29,7 @@
 #include <asm/mach/serial_sa1100.h>
 
 #include <asm/arch/cerf.h>
+#include <asm/arch/mcp.h>
 #include "generic.h"
 
 static struct resource cerfuart2_resources[] = {
@@ -116,10 +117,16 @@ static void __init cerf_map_io(void)
 	GPDR |= CERF_GPIO_CF_RESET;
 }
 
+static struct mcp_plat_data cerf_mcp_data = {
+	.mccr0		= MCCR0_ADM,
+	.sclk_rate	= 11981000,
+};
+
 static void __init cerf_init(void)
 {
 	platform_add_devices(cerf_devices, ARRAY_SIZE(cerf_devices));
 	sa11x0_set_flash_data(&cerf_flash_data, &cerf_flash_resource, 1);
+	sa11x0_set_mcp_data(&cerf_mcp_data);
 }
 
 MACHINE_START(CERF, "Intrinsyc CerfBoard/CerfCube")

arch/arm/mach-sa1100/generic.c

@@ -221,6 +221,11 @@ static struct platform_device sa11x0mcp_device = {
 	.resource	= sa11x0mcp_resources,
 };
 
+void sa11x0_set_mcp_data(struct mcp_plat_data *data)
+{
+	sa11x0mcp_device.dev.platform_data = data;
+}
+
 static struct resource sa11x0ssp_resources[] = {
 	[0] = {
 		.start	= 0x80070000,

arch/arm/mach-sa1100/generic.h

@@ -34,5 +34,8 @@ struct resource;
 extern void sa11x0_set_flash_data(struct flash_platform_data *flash,
 				  struct resource *res, int nr);
 
+struct sa11x0_ssp_plat_ops;
+extern void sa11x0_set_ssp_data(struct sa11x0_ssp_plat_ops *ops);
+
 struct irda_platform_data;
 void sa11x0_set_irda_data(struct irda_platform_data *irda);

arch/arm/mach-sa1100/lart.c

@@ -13,12 +13,23 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/mach/serial_sa1100.h>
+#include <asm/arch/mcp.h>
 
 #include "generic.h"
 
 
 #warning "include/asm/arch-sa1100/ide.h needs fixing for lart"
 
+static struct mcp_plat_data lart_mcp_data = {
+	.mccr0		= MCCR0_ADM,
+	.sclk_rate	= 11981000,
+};
+
+static void __init lart_init(void)
+{
+	sa11x0_set_mcp_data(&lart_mcp_data);
+}
+
 static struct map_desc lart_io_desc[] __initdata = {
  /* virtual     physical    length      type */
   { 0xe8000000, 0x00000000, 0x00400000, MT_DEVICE }, /* main flash memory */
@@ -47,5 +58,6 @@ MACHINE_START(LART, "LART")
 	.boot_params	= 0xc0000100,
 	.map_io		= lart_map_io,
 	.init_irq	= sa1100_init_irq,
+	.init_machine	= lart_init,
 	.timer		= &sa1100_timer,
 MACHINE_END

arch/arm/mach-sa1100/shannon.c

@@ -18,6 +18,7 @@
 #include <asm/mach/flash.h>
 #include <asm/mach/map.h>
 #include <asm/mach/serial_sa1100.h>
+#include <asm/arch/mcp.h>
 #include <asm/arch/shannon.h>
 
 #include "generic.h"
@@ -52,9 +53,15 @@ static struct resource shannon_flash_resource = {
 	.flags		= IORESOURCE_MEM,
 };
 
+static struct mcp_plat_data shannon_mcp_data = {
+	.mccr0		= MCCR0_ADM,
+	.sclk_rate	= 11981000,
+};
+
 static void __init shannon_init(void)
 {
 	sa11x0_set_flash_data(&shannon_flash_data, &shannon_flash_resource, 1);
+	sa11x0_set_mcp_data(&shannon_mcp_data);
 }
 
 static void __init shannon_map_io(void)

arch/arm/mach-sa1100/simpad.c

@@ -23,6 +23,7 @@
 #include <asm/mach/flash.h>
 #include <asm/mach/map.h>
 #include <asm/mach/serial_sa1100.h>
+#include <asm/arch/mcp.h>
 #include <asm/arch/simpad.h>
 
 #include <linux/serial_core.h>
@@ -123,6 +124,11 @@ static struct resource simpad_flash_resources [] = {
 	}
 };
 
+static struct mcp_plat_data simpad_mcp_data = {
+	.mccr0		= MCCR0_ADM,
+	.sclk_rate	= 11981000,
+};
+
 
 
 static void __init simpad_map_io(void)
@@ -157,6 +163,7 @@ static void __init simpad_map_io(void)
 
 	sa11x0_set_flash_data(&simpad_flash_data, simpad_flash_resources,
 			      ARRAY_SIZE(simpad_flash_resources));
+	sa11x0_set_mcp_data(&simpad_mcp_data);
 }
 
 static void simpad_power_off(void)

arch/arm/mm/Kconfig

@@ -384,7 +384,7 @@ config CPU_DCACHE_DISABLE
 
 config CPU_DCACHE_WRITETHROUGH
 	bool "Force write through D-cache"
-	depends on (CPU_ARM920T || CPU_ARM922T || CPU_ARM925T || CPU_ARM926T || CPU_ARM1020) && !CPU_DISABLE_DCACHE
+	depends on (CPU_ARM920T || CPU_ARM922T || CPU_ARM925T || CPU_ARM926T || CPU_ARM1020) && !CPU_DCACHE_DISABLE
 	default y if CPU_ARM925T
 	help
 	  Say Y here to use the data cache in writethrough mode. Unless you

arch/arm/mm/mm-armv.c

@@ -383,6 +383,7 @@ static void __init build_mem_type_table(void)
 {
 	struct cachepolicy *cp;
 	unsigned int cr = get_cr();
+	unsigned int user_pgprot;
 	int cpu_arch = cpu_architecture();
 	int i;
 
@@ -408,6 +409,9 @@ static void __init build_mem_type_table(void)
 		}
 	}
 
+	cp = &cache_policies[cachepolicy];
+	user_pgprot = cp->pte;
+
 	/*
 	 * ARMv6 and above have extended page tables.
 	 */
@@ -426,11 +430,18 @@ static void __init build_mem_type_table(void)
 		mem_types[MT_MINICLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 		mem_types[MT_CACHECLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 
+		/*
+		 * Mark the device area as "shared device"
+		 */
 		mem_types[MT_DEVICE].prot_pte |= L_PTE_BUFFERABLE;
 		mem_types[MT_DEVICE].prot_sect |= PMD_SECT_BUFFERED;
-	}
 
-	cp = &cache_policies[cachepolicy];
+		/*
+		 * User pages need to be mapped with the ASID
+		 * (iow, non-global)
+		 */
+		user_pgprot |= L_PTE_ASID;
+	}
 
 	if (cpu_arch >= CPU_ARCH_ARMv5) {
 		mem_types[MT_LOW_VECTORS].prot_pte |= cp->pte & PTE_CACHEABLE;
@@ -448,7 +459,7 @@ static void __init build_mem_type_table(void)
 
 	for (i = 0; i < 16; i++) {
 		unsigned long v = pgprot_val(protection_map[i]);
-		v &= (~(PTE_BUFFERABLE|PTE_CACHEABLE)) | cp->pte;
+		v &= (~(PTE_BUFFERABLE|PTE_CACHEABLE)) | user_pgprot;
 		protection_map[i] = __pgprot(v);
 	}
 

arch/arm/mm/proc-v6.S

@@ -105,18 +105,12 @@ ENTRY(cpu_v6_dcache_clean_area)
 ENTRY(cpu_v6_switch_mm)
 	mov	r2, #0
 	ldr	r1, [r1, #MM_CONTEXT_ID]	@ get mm->context.id
-	mcr     p15, 0, r2, c7, c5, 6           @ flush BTAC/BTB
+	mcr	p15, 0, r2, c7, c5, 6		@ flush BTAC/BTB
 	mcr	p15, 0, r2, c7, c10, 4		@ drain write buffer
 	mcr	p15, 0, r0, c2, c0, 0		@ set TTB 0
 	mcr	p15, 0, r1, c13, c0, 1		@ set context ID
 	mov	pc, lr
 
-#define nG	(1 << 11)
-#define APX	(1 << 9)
-#define AP1	(1 << 5)
-#define AP0	(1 << 4)
-#define XN	(1 << 0)
-
 /*
  *	cpu_v6_set_pte(ptep, pte)
  *
@@ -139,24 +133,24 @@ ENTRY(cpu_v6_switch_mm)
 ENTRY(cpu_v6_set_pte)
 	str	r1, [r0], #-2048		@ linux version
 
-	bic	r2, r1, #0x00000ff0
+	bic	r2, r1, #0x000007f0
 	bic	r2, r2, #0x00000003
-	orr	r2, r2, #AP0 | 2
+	orr	r2, r2, #PTE_EXT_AP0 | 2
 
 	tst	r1, #L_PTE_WRITE
 	tstne	r1, #L_PTE_DIRTY
-	orreq	r2, r2, #APX
+	orreq	r2, r2, #PTE_EXT_APX
 
 	tst	r1, #L_PTE_USER
-	orrne	r2, r2, #AP1 | nG
-	tstne	r2, #APX
-	bicne	r2, r2, #APX | AP0
+	orrne	r2, r2, #PTE_EXT_AP1
+	tstne	r2, #PTE_EXT_APX
+	bicne	r2, r2, #PTE_EXT_APX | PTE_EXT_AP0
 
 	tst	r1, #L_PTE_YOUNG
-	biceq	r2, r2, #APX | AP1 | AP0
+	biceq	r2, r2, #PTE_EXT_APX | PTE_EXT_AP_MASK
 
 @	tst	r1, #L_PTE_EXEC
-@	orreq	r2, r2, #XN
+@	orreq	r2, r2, #PTE_EXT_XN
 
 	tst	r1, #L_PTE_PRESENT
 	moveq	r2, #0

arch/arm/nwfpe/fpopcode.h

@@ -370,20 +370,20 @@ TABLE 5
 #define getRoundingMode(opcode)		((opcode & MASK_ROUNDING_MODE) >> 5)
 
 #ifdef CONFIG_FPE_NWFPE_XP
-static inline const floatx80 getExtendedConstant(const unsigned int nIndex)
+static inline __attribute_pure__ floatx80 getExtendedConstant(const unsigned int nIndex)
 {
 	extern const floatx80 floatx80Constant[];
 	return floatx80Constant[nIndex];
 }
 #endif
 
-static inline const float64 getDoubleConstant(const unsigned int nIndex)
+static inline __attribute_pure__ float64 getDoubleConstant(const unsigned int nIndex)
 {
 	extern const float64 float64Constant[];
 	return float64Constant[nIndex];
 }
 
-static inline const float32 getSingleConstant(const unsigned int nIndex)
+static inline __attribute_pure__ float32 getSingleConstant(const unsigned int nIndex)
 {
 	extern const float32 float32Constant[];
 	return float32Constant[nIndex];

arch/arm/nwfpe/softfloat.c

@@ -1602,9 +1602,7 @@ flag float32_le_quiet( float32 a, float32 b )
     if (    ( ( extractFloat32Exp( a ) == 0xFF ) && extractFloat32Frac( a ) )
          || ( ( extractFloat32Exp( b ) == 0xFF ) && extractFloat32Frac( b ) )
        ) {
-        if ( float32_is_signaling_nan( a ) || float32_is_signaling_nan( b ) ) {
-            float_raise( float_flag_invalid );
-        }
+        /* Do nothing, even if NaN as we're quiet */
         return 0;
     }
     aSign = extractFloat32Sign( a );
@@ -1629,9 +1627,7 @@ flag float32_lt_quiet( float32 a, float32 b )
     if (    ( ( extractFloat32Exp( a ) == 0xFF ) && extractFloat32Frac( a ) )
          || ( ( extractFloat32Exp( b ) == 0xFF ) && extractFloat32Frac( b ) )
        ) {
-        if ( float32_is_signaling_nan( a ) || float32_is_signaling_nan( b ) ) {
-            float_raise( float_flag_invalid );
-        }
+        /* Do nothing, even if NaN as we're quiet */
         return 0;
     }
     aSign = extractFloat32Sign( a );
@@ -2493,9 +2489,7 @@ flag float64_le_quiet( float64 a, float64 b )
     if (    ( ( extractFloat64Exp( a ) == 0x7FF ) && extractFloat64Frac( a ) )
          || ( ( extractFloat64Exp( b ) == 0x7FF ) && extractFloat64Frac( b ) )
        ) {
-        if ( float64_is_signaling_nan( a ) || float64_is_signaling_nan( b ) ) {
-            float_raise( float_flag_invalid );
-        }
+        /* Do nothing, even if NaN as we're quiet */
         return 0;
     }
     aSign = extractFloat64Sign( a );
@@ -2520,9 +2514,7 @@ flag float64_lt_quiet( float64 a, float64 b )
     if (    ( ( extractFloat64Exp( a ) == 0x7FF ) && extractFloat64Frac( a ) )
          || ( ( extractFloat64Exp( b ) == 0x7FF ) && extractFloat64Frac( b ) )
        ) {
-        if ( float64_is_signaling_nan( a ) || float64_is_signaling_nan( b ) ) {
-            float_raise( float_flag_invalid );
-        }
+        /* Do nothing, even if NaN as we're quiet */
         return 0;
     }
     aSign = extractFloat64Sign( a );
@@ -3256,7 +3248,7 @@ flag floatx80_eq( floatx80 a, floatx80 b )
        ) {
         if (    floatx80_is_signaling_nan( a )
              || floatx80_is_signaling_nan( b ) ) {
-            roundData->exception |= float_flag_invalid;
+            float_raise( float_flag_invalid );
         }
         return 0;
     }
@@ -3286,7 +3278,7 @@ flag floatx80_le( floatx80 a, floatx80 b )
          || (    ( extractFloatx80Exp( b ) == 0x7FFF )
               && (bits64) ( extractFloatx80Frac( b )<<1 ) )
        ) {
-        roundData->exception |= float_flag_invalid;
+        float_raise( float_flag_invalid );
         return 0;
     }
     aSign = extractFloatx80Sign( a );
@@ -3320,7 +3312,7 @@ flag floatx80_lt( floatx80 a, floatx80 b )
          || (    ( extractFloatx80Exp( b ) == 0x7FFF )
               && (bits64) ( extractFloatx80Frac( b )<<1 ) )
        ) {
-        roundData->exception |= float_flag_invalid;
+        float_raise( float_flag_invalid );
         return 0;
     }
     aSign = extractFloatx80Sign( a );
@@ -3353,7 +3345,7 @@ flag floatx80_eq_signaling( floatx80 a, floatx80 b )
          || (    ( extractFloatx80Exp( b ) == 0x7FFF )
               && (bits64) ( extractFloatx80Frac( b )<<1 ) )
        ) {
-        roundData->exception |= float_flag_invalid;
+        float_raise( float_flag_invalid );
         return 0;
     }
     return
@@ -3382,10 +3374,7 @@ flag floatx80_le_quiet( floatx80 a, floatx80 b )
          || (    ( extractFloatx80Exp( b ) == 0x7FFF )
               && (bits64) ( extractFloatx80Frac( b )<<1 ) )
        ) {
-        if (    floatx80_is_signaling_nan( a )
-             || floatx80_is_signaling_nan( b ) ) {
-            roundData->exception |= float_flag_invalid;
-        }
+        /* Do nothing, even if NaN as we're quiet */
         return 0;
     }
     aSign = extractFloatx80Sign( a );
@@ -3419,10 +3408,7 @@ flag floatx80_lt_quiet( floatx80 a, floatx80 b )
          || (    ( extractFloatx80Exp( b ) == 0x7FFF )
               && (bits64) ( extractFloatx80Frac( b )<<1 ) )
        ) {
-        if (    floatx80_is_signaling_nan( a )
-             || floatx80_is_signaling_nan( b ) ) {
-            roundData->exception |= float_flag_invalid;
-        }
+        /* Do nothing, even if NaN as we're quiet */
         return 0;
     }
     aSign = extractFloatx80Sign( a );

arch/arm26/kernel/signal.c

@@ -454,14 +454,13 @@ handle_signal(unsigned long sig, siginfo_t *info, sigset_t *oldset,
 		if (ka->sa.sa_flags & SA_ONESHOT)
 			ka->sa.sa_handler = SIG_DFL;
 
-		if (!(ka->sa.sa_flags & SA_NODEFER)) {
-			spin_lock_irq(&tsk->sighand->siglock);
-			sigorsets(&tsk->blocked, &tsk->blocked,
-				  &ka->sa.sa_mask);
+		spin_lock_irq(&tsk->sighand->siglock);
+		sigorsets(&tsk->blocked, &tsk->blocked,
+			  &ka->sa.sa_mask);
+		if (!(ka->sa.sa_flags & SA_NODEFER))
 			sigaddset(&tsk->blocked, sig);
-			recalc_sigpending();
-			spin_unlock_irq(&tsk->sighand->siglock);
-		}
+		recalc_sigpending();
+		spin_unlock_irq(&tsk->sighand->siglock);
 		return;
 	}
 

arch/cris/arch-v10/kernel/signal.c

@@ -517,13 +517,12 @@ handle_signal(int canrestart, unsigned long sig,
 	if (ka->sa.sa_flags & SA_ONESHOT)
 		ka->sa.sa_handler = SIG_DFL;
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/cris/arch-v32/kernel/signal.c

@@ -568,13 +568,12 @@ handle_signal(int canrestart, unsigned long sig,
 	if (ka->sa.sa_flags & SA_ONESHOT)
 		ka->sa.sa_handler = SIG_DFL;
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/frv/kernel/signal.c

@@ -506,13 +506,12 @@ static void handle_signal(unsigned long sig, siginfo_t *info,
 	else
 		setup_frame(sig, ka, oldset, regs);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked, &current->blocked, &ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked, &current->blocked, &ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked, sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 } /* end handle_signal() */
 
 /*****************************************************************************/

arch/h8300/kernel/signal.c

@@ -488,13 +488,12 @@ handle_signal(unsigned long sig, siginfo_t *info, struct k_sigaction *ka,
 	else
 		setup_frame(sig, ka, oldset, regs);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/i386/kernel/apic.c

@@ -726,15 +726,11 @@ __setup("apic=", apic_set_verbosity);
 static int __init detect_init_APIC (void)
 {
 	u32 h, l, features;
-	extern void get_cpu_vendor(struct cpuinfo_x86*);
 
 	/* Disabled by kernel option? */
 	if (enable_local_apic < 0)
 		return -1;
 
-	/* Workaround for us being called before identify_cpu(). */
-	get_cpu_vendor(&boot_cpu_data);
-
 	switch (boot_cpu_data.x86_vendor) {
 	case X86_VENDOR_AMD:
 		if ((boot_cpu_data.x86 == 6 && boot_cpu_data.x86_model > 1) ||

arch/i386/kernel/nmi.c

@@ -195,7 +195,7 @@ static void disable_lapic_nmi_watchdog(void)
 			wrmsr(MSR_P6_EVNTSEL0, 0, 0);
 			break;
 		case 15:
-			if (boot_cpu_data.x86_model > 0x3)
+			if (boot_cpu_data.x86_model > 0x4)
 				break;
 
 			wrmsr(MSR_P4_IQ_CCCR0, 0, 0);
@@ -432,7 +432,7 @@ void setup_apic_nmi_watchdog (void)
 			setup_p6_watchdog();
 			break;
 		case 15:
-			if (boot_cpu_data.x86_model > 0x3)
+			if (boot_cpu_data.x86_model > 0x4)
 				return;
 
 			if (!setup_p4_watchdog())

arch/i386/kernel/signal.c

@@ -577,10 +577,11 @@ handle_signal(unsigned long sig, siginfo_t *info, struct k_sigaction *ka,
 	else
 		ret = setup_frame(sig, ka, oldset, regs);
 
-	if (ret && !(ka->sa.sa_flags & SA_NODEFER)) {
+	if (ret) {
 		spin_lock_irq(&current->sighand->siglock);
 		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
-		sigaddset(&current->blocked,sig);
+		if (!(ka->sa.sa_flags & SA_NODEFER))
+			sigaddset(&current->blocked,sig);
 		recalc_sigpending();
 		spin_unlock_irq(&current->sighand->siglock);
 	}

arch/i386/kernel/traps.c

@@ -803,15 +803,17 @@ void math_error(void __user *eip)
 	 */
 	cwd = get_fpu_cwd(task);
 	swd = get_fpu_swd(task);
-	switch (((~cwd) & swd & 0x3f) | (swd & 0x240)) {
+	switch (swd & ~cwd & 0x3f) {
 		case 0x000:
 		default:
 			break;
 		case 0x001: /* Invalid Op */
-		case 0x041: /* Stack Fault */
-		case 0x241: /* Stack Fault | Direction */
+			/*
+			 * swd & 0x240 == 0x040: Stack Underflow
+			 * swd & 0x240 == 0x240: Stack Overflow
+			 * User must clear the SF bit (0x40) if set
+			 */
 			info.si_code = FPE_FLTINV;
-			/* Should we clear the SF or let user space do it ???? */
 			break;
 		case 0x002: /* Denormalize */
 		case 0x010: /* Underflow */

arch/ia64/Kconfig

@@ -392,15 +392,8 @@ menu "Bus options (PCI, PCMCIA)"
 config PCI
 	bool "PCI support"
 	help
-	  Find out whether you have a PCI motherboard. PCI is the name of a
-	  bus system, i.e. the way the CPU talks to the other stuff inside
-	  your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
-	  VESA. If you have PCI, say Y, otherwise N.
-
-	  The PCI-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>, contains valuable
-	  information about which PCI hardware does work under Linux and which
-	  doesn't.
+	  Real IA-64 machines all have PCI/PCI-X/PCI Express busses.  Say Y
+	  here unless you are using a simulator without PCI support.
 
 config PCI_DOMAINS
 	bool

arch/ia64/configs/sn2_defconfig

@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.10
-# Mon Jan 10 13:57:35 2005
+# Linux kernel version: 2.6.13-rc6
+# Tue Aug 16 14:40:41 2005
 #
 
 #
@@ -10,6 +10,7 @@
 CONFIG_EXPERIMENTAL=y
 CONFIG_CLEAN_COMPILE=y
 CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
 
 #
 # General setup
@@ -21,24 +22,26 @@ CONFIG_POSIX_MQUEUE=y
 # CONFIG_BSD_PROCESS_ACCT is not set
 CONFIG_SYSCTL=y
 # CONFIG_AUDIT is not set
-CONFIG_LOG_BUF_SHIFT=20
 CONFIG_HOTPLUG=y
 CONFIG_KOBJECT_UEVENT=y
 # CONFIG_IKCONFIG is not set
+CONFIG_CPUSETS=y
 # CONFIG_EMBEDDED is not set
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 CONFIG_EPOLL=y
-CONFIG_CPUSETS=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_SHMEM=y
 CONFIG_CC_ALIGN_FUNCTIONS=0
 CONFIG_CC_ALIGN_LABELS=0
 CONFIG_CC_ALIGN_LOOPS=0
 CONFIG_CC_ALIGN_JUMPS=0
 # CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
 
 #
 # Loadable module support
@@ -63,9 +66,12 @@ CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_TIME_INTERPOLATION=y
 CONFIG_EFI=y
 CONFIG_GENERIC_IOMAP=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_IA64_UNCACHED_ALLOCATOR=y
 # CONFIG_IA64_GENERIC is not set
 # CONFIG_IA64_DIG is not set
 # CONFIG_IA64_HP_ZX1 is not set
+# CONFIG_IA64_HP_ZX1_SWIOTLB is not set
 CONFIG_IA64_SGI_SN2=y
 # CONFIG_IA64_HP_SIM is not set
 # CONFIG_ITANIUM is not set
@@ -74,6 +80,10 @@ CONFIG_MCKINLEY=y
 # CONFIG_IA64_PAGE_SIZE_8KB is not set
 CONFIG_IA64_PAGE_SIZE_16KB=y
 # CONFIG_IA64_PAGE_SIZE_64KB is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
 CONFIG_IA64_L1_CACHE_SHIFT=7
 CONFIG_NUMA=y
 CONFIG_VIRTUAL_MEM_MAP=y
@@ -81,11 +91,20 @@ CONFIG_HOLES_IN_ZONE=y
 CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
 # CONFIG_IA64_CYCLONE is not set
 CONFIG_IOSAPIC=y
+CONFIG_IA64_SGI_SN_XP=m
 CONFIG_FORCE_MAX_ZONEORDER=18
 CONFIG_SMP=y
 CONFIG_NR_CPUS=512
 # CONFIG_HOTPLUG_CPU is not set
+CONFIG_SCHED_SMT=y
 CONFIG_PREEMPT=y
+CONFIG_SELECT_MEMORY_MODEL=y
+# CONFIG_FLATMEM_MANUAL is not set
+CONFIG_DISCONTIGMEM_MANUAL=y
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_DISCONTIGMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_NEED_MULTIPLE_NODES=y
 CONFIG_HAVE_DEC_LOCK=y
 CONFIG_IA32_SUPPORT=y
 CONFIG_COMPAT=y
@@ -105,6 +124,7 @@ CONFIG_BINFMT_ELF=y
 #
 # Power management and ACPI
 #
+CONFIG_PM=y
 CONFIG_ACPI=y
 
 #
@@ -114,6 +134,7 @@ CONFIG_ACPI_BOOT=y
 CONFIG_ACPI_INTERPRETER=y
 # CONFIG_ACPI_BUTTON is not set
 CONFIG_ACPI_VIDEO=m
+CONFIG_ACPI_HOTKEY=m
 # CONFIG_ACPI_FAN is not set
 # CONFIG_ACPI_PROCESSOR is not set
 CONFIG_ACPI_NUMA=y
@@ -133,6 +154,7 @@ CONFIG_PCI_DOMAINS=y
 # CONFIG_PCI_MSI is not set
 CONFIG_PCI_LEGACY_PROC=y
 CONFIG_PCI_NAMES=y
+# CONFIG_PCI_DEBUG is not set
 
 #
 # PCI Hotplug Support
@@ -141,7 +163,6 @@ CONFIG_HOTPLUG_PCI=y
 # CONFIG_HOTPLUG_PCI_FAKE is not set
 # CONFIG_HOTPLUG_PCI_ACPI is not set
 # CONFIG_HOTPLUG_PCI_CPCI is not set
-# CONFIG_HOTPLUG_PCI_PCIE is not set
 # CONFIG_HOTPLUG_PCI_SHPC is not set
 CONFIG_HOTPLUG_PCI_SGI=y
 
@@ -151,8 +172,70 @@ CONFIG_HOTPLUG_PCI_SGI=y
 # CONFIG_PCCARD is not set
 
 #
-# PC-card bridges
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_IP_TCPDIAG=y
+# CONFIG_IP_TCPDIAG_IPV6 is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+CONFIG_IPV6=m
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_NETFILTER is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set
+
+#
+# Network testing
 #
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
 
 #
 # Device Drivers
@@ -163,7 +246,7 @@ CONFIG_HOTPLUG_PCI_SGI=y
 #
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
 # CONFIG_DEBUG_DRIVER is not set
 
 #
@@ -188,6 +271,7 @@ CONFIG_FW_LOADER=m
 # CONFIG_BLK_CPQ_CISS_DA is not set
 # CONFIG_BLK_DEV_DAC960 is not set
 # CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_CRYPTOLOOP=m
 CONFIG_BLK_DEV_NBD=m
@@ -252,6 +336,7 @@ CONFIG_IDEDMA_PCI_AUTO=y
 # CONFIG_BLK_DEV_HPT366 is not set
 # CONFIG_BLK_DEV_SC1200 is not set
 # CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT821X is not set
 # CONFIG_BLK_DEV_NS87415 is not set
 # CONFIG_BLK_DEV_PDC202XX_OLD is not set
 # CONFIG_BLK_DEV_PDC202XX_NEW is not set
@@ -282,6 +367,7 @@ CONFIG_CHR_DEV_ST=m
 CONFIG_BLK_DEV_SR=m
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=m
+CONFIG_CHR_DEV_SCH=m
 
 #
 # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
@@ -315,24 +401,20 @@ CONFIG_SCSI_SATA=y
 # CONFIG_SCSI_ATA_PIIX is not set
 # CONFIG_SCSI_SATA_NV is not set
 # CONFIG_SCSI_SATA_PROMISE is not set
+# CONFIG_SCSI_SATA_QSTOR is not set
 # CONFIG_SCSI_SATA_SX4 is not set
 # CONFIG_SCSI_SATA_SIL is not set
 # CONFIG_SCSI_SATA_SIS is not set
 # CONFIG_SCSI_SATA_ULI is not set
 # CONFIG_SCSI_SATA_VIA is not set
 CONFIG_SCSI_SATA_VITESSE=y
-# CONFIG_SCSI_BUSLOGIC is not set
 # CONFIG_SCSI_DMX3191D is not set
-# CONFIG_SCSI_EATA is not set
-# CONFIG_SCSI_EATA_PIO is not set
 # CONFIG_SCSI_FUTURE_DOMAIN is not set
-# CONFIG_SCSI_GDTH is not set
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
-# CONFIG_SCSI_QLOGIC_ISP is not set
 # CONFIG_SCSI_QLOGIC_FC is not set
 CONFIG_SCSI_QLOGIC_1280=y
 # CONFIG_SCSI_QLOGIC_1280_1040 is not set
@@ -342,6 +424,8 @@ CONFIG_SCSI_QLA22XX=y
 CONFIG_SCSI_QLA2300=y
 CONFIG_SCSI_QLA2322=y
 # CONFIG_SCSI_QLA6312 is not set
+# CONFIG_SCSI_QLA24XX is not set
+# CONFIG_SCSI_LPFC is not set
 # CONFIG_SCSI_DC395x is not set
 # CONFIG_SCSI_DC390T is not set
 # CONFIG_SCSI_DEBUG is not set
@@ -364,11 +448,15 @@ CONFIG_DM_CRYPT=m
 CONFIG_DM_SNAPSHOT=m
 CONFIG_DM_MIRROR=m
 CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_DM_MULTIPATH_EMC=m
 
 #
 # Fusion MPT device support
 #
 CONFIG_FUSION=y
+CONFIG_FUSION_SPI=y
+CONFIG_FUSION_FC=y
 CONFIG_FUSION_MAX_SGE=128
 CONFIG_FUSION_CTL=m
 
@@ -383,82 +471,13 @@ CONFIG_FUSION_CTL=m
 # CONFIG_I2O is not set
 
 #
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-CONFIG_PACKET_MMAP=y
-CONFIG_NETLINK_DEV=y
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-# CONFIG_IP_ADVANCED_ROUTER is not set
-# CONFIG_IP_PNP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_IP_MROUTE is not set
-# CONFIG_ARPD is not set
-CONFIG_SYN_COOKIES=y
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_IP_TCPDIAG=y
-# CONFIG_IP_TCPDIAG_IPV6 is not set
-CONFIG_IPV6=m
-# CONFIG_IPV6_PRIVACY is not set
-# CONFIG_INET6_AH is not set
-# CONFIG_INET6_ESP is not set
-# CONFIG_INET6_IPCOMP is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_IPV6_TUNNEL is not set
-# CONFIG_NETFILTER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-# CONFIG_NET_CLS_ROUTE is not set
-
-#
-# Network testing
+# Network device support
 #
-# CONFIG_NET_PKTGEN is not set
-CONFIG_NETPOLL=y
-# CONFIG_NETPOLL_RX is not set
-# CONFIG_NETPOLL_TRAP is not set
-CONFIG_NET_POLL_CONTROLLER=y
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
 CONFIG_NETDEVICES=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_EQUALIZER is not set
 # CONFIG_TUN is not set
-# CONFIG_ETHERTAP is not set
 
 #
 # ARCnet devices
@@ -480,8 +499,10 @@ CONFIG_NETDEVICES=y
 # CONFIG_HAMACHI is not set
 # CONFIG_YELLOWFIN is not set
 # CONFIG_R8169 is not set
+# CONFIG_SKGE is not set
 # CONFIG_SK98LIN is not set
 CONFIG_TIGON3=y
+# CONFIG_BNX2 is not set
 
 #
 # Ethernet (10000 Mbit)
@@ -512,6 +533,10 @@ CONFIG_S2IO=m
 # CONFIG_NET_FC is not set
 # CONFIG_SHAPER is not set
 CONFIG_NETCONSOLE=y
+CONFIG_NETPOLL=y
+# CONFIG_NETPOLL_RX is not set
+# CONFIG_NETPOLL_TRAP is not set
+CONFIG_NET_POLL_CONTROLLER=y
 
 #
 # ISDN subsystem
@@ -540,14 +565,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
 # CONFIG_INPUT_EVDEV is not set
 # CONFIG_INPUT_EVBUG is not set
 
-#
-# Input I/O drivers
-#
-# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
-# CONFIG_SERIO is not set
-# CONFIG_SERIO_I8042 is not set
-
 #
 # Input Device Drivers
 #
@@ -557,6 +574,12 @@ CONFIG_SOUND_GAMEPORT=y
 # CONFIG_INPUT_TOUCHSCREEN is not set
 # CONFIG_INPUT_MISC is not set
 
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
 #
 # Character devices
 #
@@ -568,9 +591,10 @@ CONFIG_SERIAL_NONSTANDARD=y
 # CONFIG_CYCLADES is not set
 # CONFIG_MOXA_SMARTIO is not set
 # CONFIG_ISI is not set
-# CONFIG_SYNCLINK is not set
 # CONFIG_SYNCLINKMP is not set
 # CONFIG_N_HDLC is not set
+# CONFIG_SPECIALIX is not set
+# CONFIG_SX is not set
 # CONFIG_STALDRV is not set
 CONFIG_SGI_SNSC=y
 CONFIG_SGI_TIOCX=y
@@ -587,6 +611,7 @@ CONFIG_SGI_MBCS=m
 CONFIG_SERIAL_CORE=y
 CONFIG_SERIAL_CORE_CONSOLE=y
 CONFIG_SERIAL_SGI_L1_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
 CONFIG_SERIAL_SGI_IOC4=y
 CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
@@ -615,18 +640,30 @@ CONFIG_EFI_RTC=y
 CONFIG_RAW_DRIVER=m
 # CONFIG_HPET is not set
 CONFIG_MAX_RAW_DEVS=256
+# CONFIG_HANGCHECK_TIMER is not set
 CONFIG_MMTIMER=y
 
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
 #
 # I2C support
 #
 # CONFIG_I2C is not set
+# CONFIG_I2C_SENSOR is not set
 
 #
 # Dallas's 1-wire bus
 #
 # CONFIG_W1 is not set
 
+#
+# Hardware Monitoring support
+#
+# CONFIG_HWMON is not set
+
 #
 # Misc devices
 #
@@ -660,6 +697,8 @@ CONFIG_DUMMY_CONSOLE=y
 #
 # USB support
 #
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
 CONFIG_USB=m
 # CONFIG_USB_DEBUG is not set
 
@@ -669,9 +708,8 @@ CONFIG_USB=m
 # CONFIG_USB_DEVICEFS is not set
 # CONFIG_USB_BANDWIDTH is not set
 # CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
 # CONFIG_USB_OTG is not set
-CONFIG_USB_ARCH_HAS_HCD=y
-CONFIG_USB_ARCH_HAS_OHCI=y
 
 #
 # USB Host Controller Drivers
@@ -679,7 +717,10 @@ CONFIG_USB_ARCH_HAS_OHCI=y
 CONFIG_USB_EHCI_HCD=m
 # CONFIG_USB_EHCI_SPLIT_ISO is not set
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_ISP116X_HCD is not set
 CONFIG_USB_OHCI_HCD=m
+# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
 CONFIG_USB_UHCI_HCD=m
 # CONFIG_USB_SL811_HCD is not set
 
@@ -710,12 +751,15 @@ CONFIG_USB_HIDINPUT=y
 # CONFIG_USB_MOUSE is not set
 # CONFIG_USB_AIPTEK is not set
 # CONFIG_USB_WACOM is not set
+# CONFIG_USB_ACECAD is not set
 # CONFIG_USB_KBTAB is not set
 # CONFIG_USB_POWERMATE is not set
 # CONFIG_USB_MTOUCH is not set
+# CONFIG_USB_ITMTOUCH is not set
 # CONFIG_USB_EGALAX is not set
 # CONFIG_USB_XPAD is not set
 # CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_KEYSPAN_REMOTE is not set
 
 #
 # USB Imaging devices
@@ -740,6 +784,7 @@ CONFIG_USB_HIDINPUT=y
 # CONFIG_USB_PEGASUS is not set
 # CONFIG_USB_RTL8150 is not set
 # CONFIG_USB_USBNET is not set
+CONFIG_USB_MON=y
 
 #
 # USB port drivers
@@ -763,9 +808,12 @@ CONFIG_USB_HIDINPUT=y
 # CONFIG_USB_CYTHERM is not set
 # CONFIG_USB_PHIDGETKIT is not set
 # CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
 
 #
-# USB ATM/DSL drivers
+# USB DSL modem support
 #
 
 #
@@ -782,6 +830,7 @@ CONFIG_USB_HIDINPUT=y
 # InfiniBand support
 #
 CONFIG_INFINIBAND=m
+CONFIG_INFINIBAND_USER_VERBS=m
 CONFIG_INFINIBAND_MTHCA=m
 # CONFIG_INFINIBAND_MTHCA_DEBUG is not set
 CONFIG_INFINIBAND_IPOIB=m
@@ -799,6 +848,7 @@ CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
 CONFIG_EXT2_FS_SECURITY=y
+# CONFIG_EXT2_FS_XIP is not set
 CONFIG_EXT3_FS=y
 CONFIG_EXT3_FS_XATTR=y
 CONFIG_EXT3_FS_POSIX_ACL=y
@@ -814,13 +864,19 @@ CONFIG_REISERFS_FS_POSIX_ACL=y
 CONFIG_REISERFS_FS_SECURITY=y
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
+
+#
+# XFS support
+#
 CONFIG_XFS_FS=y
+CONFIG_XFS_EXPORT=y
 CONFIG_XFS_RT=y
 CONFIG_XFS_QUOTA=y
 # CONFIG_XFS_SECURITY is not set
 CONFIG_XFS_POSIX_ACL=y
 # CONFIG_MINIX_FS is not set
 # CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
 CONFIG_QUOTA=y
 # CONFIG_QFMT_V1 is not set
 # CONFIG_QFMT_V2 is not set
@@ -854,7 +910,6 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
 CONFIG_PROC_FS=y
 CONFIG_PROC_KCORE=y
 CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
 # CONFIG_DEVPTS_FS_XATTR is not set
 CONFIG_TMPFS=y
 CONFIG_TMPFS_XATTR=y
@@ -885,15 +940,18 @@ CONFIG_RAMFS=y
 #
 CONFIG_NFS_FS=m
 CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
 CONFIG_NFS_DIRECTIO=y
 CONFIG_NFSD=m
 CONFIG_NFSD_V3=y
+# CONFIG_NFSD_V3_ACL is not set
 CONFIG_NFSD_V4=y
 CONFIG_NFSD_TCP=y
 CONFIG_LOCKD=m
 CONFIG_LOCKD_V4=y
-CONFIG_EXPORTFS=m
+CONFIG_EXPORTFS=y
+CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=m
 CONFIG_SUNRPC_GSS=m
 CONFIG_RPCSEC_GSS_KRB5=m
@@ -980,6 +1038,9 @@ CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=m
 CONFIG_ZLIB_DEFLATE=m
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
 
 #
 # Profiling support
@@ -989,15 +1050,19 @@ CONFIG_ZLIB_DEFLATE=m
 #
 # Kernel hacking
 #
+# CONFIG_PRINTK_TIME is not set
 CONFIG_DEBUG_KERNEL=y
 CONFIG_MAGIC_SYSRQ=y
+CONFIG_LOG_BUF_SHIFT=20
 # CONFIG_SCHEDSTATS is not set
 # CONFIG_DEBUG_SLAB is not set
+CONFIG_DEBUG_PREEMPT=y
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_KOBJECT is not set
 CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_FS is not set
+# CONFIG_KPROBES is not set
 CONFIG_IA64_GRANULE_16MB=y
 # CONFIG_IA64_GRANULE_64MB is not set
 # CONFIG_IA64_PRINT_HAZARDS is not set
@@ -1019,11 +1084,12 @@ CONFIG_CRYPTO=y
 CONFIG_CRYPTO_HMAC=y
 # CONFIG_CRYPTO_NULL is not set
 # CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=m
+CONFIG_CRYPTO_MD5=y
 CONFIG_CRYPTO_SHA1=m
 # CONFIG_CRYPTO_SHA256 is not set
 # CONFIG_CRYPTO_SHA512 is not set
 # CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
 CONFIG_CRYPTO_DES=m
 # CONFIG_CRYPTO_BLOWFISH is not set
 # CONFIG_CRYPTO_TWOFISH is not set

arch/ia64/configs/tiger_defconfig

@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.13-rc1-20050629
-# Wed Jun 29 15:28:12 2005
+# Linux kernel version: 2.6.13-rc6-tiger-smp
+# Wed Aug 17 10:19:51 2005
 #
 
 #
@@ -132,6 +132,7 @@ CONFIG_ACPI_BOOT=y
 CONFIG_ACPI_INTERPRETER=y
 CONFIG_ACPI_BUTTON=m
 # CONFIG_ACPI_VIDEO is not set
+# CONFIG_ACPI_HOTKEY is not set
 CONFIG_ACPI_FAN=m
 CONFIG_ACPI_PROCESSOR=m
 # CONFIG_ACPI_HOTPLUG_CPU is not set
@@ -169,6 +170,66 @@ CONFIG_HOTPLUG_PCI_ACPI=m
 #
 # CONFIG_PCCARD is not set
 
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+CONFIG_ARPD=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_IP_TCPDIAG=y
+# CONFIG_IP_TCPDIAG_IPV6 is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_IPV6 is not set
+# CONFIG_NETFILTER is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+
 #
 # Device Drivers
 #
@@ -178,7 +239,7 @@ CONFIG_HOTPLUG_PCI_ACPI=m
 #
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
+CONFIG_FW_LOADER=m
 # CONFIG_DEBUG_DRIVER is not set
 
 #
@@ -348,6 +409,7 @@ CONFIG_SCSI_QLA22XX=m
 CONFIG_SCSI_QLA2300=m
 CONFIG_SCSI_QLA2322=m
 # CONFIG_SCSI_QLA6312 is not set
+# CONFIG_SCSI_QLA24XX is not set
 # CONFIG_SCSI_LPFC is not set
 # CONFIG_SCSI_DC395x is not set
 # CONFIG_SCSI_DC390T is not set
@@ -393,72 +455,8 @@ CONFIG_FUSION_CTL=y
 # CONFIG_I2O is not set
 
 #
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
+# Network device support
 #
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-# CONFIG_IP_PNP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_IP_MROUTE is not set
-CONFIG_ARPD=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_IP_TCPDIAG=y
-# CONFIG_IP_TCPDIAG_IPV6 is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
-# CONFIG_NETFILTER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-# CONFIG_NET_CLS_ROUTE is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-CONFIG_NETPOLL=y
-# CONFIG_NETPOLL_RX is not set
-# CONFIG_NETPOLL_TRAP is not set
-CONFIG_NET_POLL_CONTROLLER=y
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
 CONFIG_NETDEVICES=y
 CONFIG_DUMMY=m
 # CONFIG_BONDING is not set
@@ -555,6 +553,10 @@ CONFIG_TIGON3=y
 # CONFIG_NET_FC is not set
 # CONFIG_SHAPER is not set
 CONFIG_NETCONSOLE=y
+CONFIG_NETPOLL=y
+# CONFIG_NETPOLL_RX is not set
+# CONFIG_NETPOLL_TRAP is not set
+CONFIG_NET_POLL_CONTROLLER=y
 
 #
 # ISDN subsystem
@@ -680,6 +682,7 @@ CONFIG_DRM_R128=m
 CONFIG_DRM_RADEON=m
 CONFIG_DRM_MGA=m
 CONFIG_DRM_SIS=m
+# CONFIG_DRM_VIA is not set
 CONFIG_RAW_DRIVER=m
 CONFIG_HPET=y
 # CONFIG_HPET_RTC_IRQ is not set
@@ -696,12 +699,19 @@ CONFIG_MAX_RAW_DEVS=256
 # I2C support
 #
 # CONFIG_I2C is not set
+# CONFIG_I2C_SENSOR is not set
 
 #
 # Dallas's 1-wire bus
 #
 # CONFIG_W1 is not set
 
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
 #
 # Misc devices
 #
@@ -800,6 +810,7 @@ CONFIG_USB_HIDINPUT=y
 # CONFIG_USB_EGALAX is not set
 # CONFIG_USB_XPAD is not set
 # CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_KEYSPAN_REMOTE is not set
 
 #
 # USB Imaging devices
@@ -850,6 +861,7 @@ CONFIG_USB_HIDINPUT=y
 # CONFIG_USB_PHIDGETSERVO is not set
 # CONFIG_USB_IDMOUSE is not set
 # CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
 # CONFIG_USB_TEST is not set
 
 #
@@ -910,6 +922,7 @@ CONFIG_XFS_EXPORT=y
 # CONFIG_XFS_POSIX_ACL is not set
 # CONFIG_MINIX_FS is not set
 # CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
 # CONFIG_QUOTA is not set
 CONFIG_DNOTIFY=y
 CONFIG_AUTOFS_FS=y

arch/ia64/configs/zx1_defconfig

@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.13-rc1-20050629
-# Wed Jun 29 15:31:11 2005
+# Linux kernel version: 2.6.13-rc6
+# Wed Aug 17 10:02:43 2005
 #
 
 #
@@ -132,6 +132,7 @@ CONFIG_ACPI_BOOT=y
 CONFIG_ACPI_INTERPRETER=y
 CONFIG_ACPI_BUTTON=y
 CONFIG_ACPI_VIDEO=m
+CONFIG_ACPI_HOTKEY=m
 CONFIG_ACPI_FAN=y
 CONFIG_ACPI_PROCESSOR=y
 CONFIG_ACPI_THERMAL=y
@@ -168,6 +169,83 @@ CONFIG_HOTPLUG_PCI_ACPI=y
 #
 # CONFIG_PCCARD is not set
 
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_IP_TCPDIAG is not set
+# CONFIG_IP_TCPDIAG_IPV6 is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+
+#
+# IP: Virtual Server Configuration
+#
+# CONFIG_IP_VS is not set
+# CONFIG_IPV6 is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_IP_NF_CONNTRACK is not set
+# CONFIG_IP_NF_CONNTRACK_MARK is not set
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+CONFIG_IP_NF_ARPTABLES=y
+# CONFIG_IP_NF_ARPFILTER is not set
+# CONFIG_IP_NF_ARP_MANGLE is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+
 #
 # Device Drivers
 #
@@ -349,6 +427,7 @@ CONFIG_SCSI_QLA2XXX=y
 # CONFIG_SCSI_QLA2300 is not set
 # CONFIG_SCSI_QLA2322 is not set
 # CONFIG_SCSI_QLA6312 is not set
+# CONFIG_SCSI_QLA24XX is not set
 # CONFIG_SCSI_LPFC is not set
 # CONFIG_SCSI_DC395x is not set
 # CONFIG_SCSI_DC390T is not set
@@ -362,9 +441,11 @@ CONFIG_SCSI_QLA2XXX=y
 #
 # Fusion MPT device support
 #
-# CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
+CONFIG_FUSION=y
+CONFIG_FUSION_SPI=y
+CONFIG_FUSION_FC=y
+CONFIG_FUSION_MAX_SGE=128
+CONFIG_FUSION_CTL=m
 
 #
 # IEEE 1394 (FireWire) support
@@ -377,87 +458,8 @@ CONFIG_SCSI_QLA2XXX=y
 # CONFIG_I2O is not set
 
 #
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-# CONFIG_IP_PNP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_IP_MROUTE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_IP_TCPDIAG is not set
-# CONFIG_IP_TCPDIAG_IPV6 is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-
-#
-# IP: Virtual Server Configuration
-#
-# CONFIG_IP_VS is not set
-# CONFIG_IPV6 is not set
-CONFIG_NETFILTER=y
-# CONFIG_NETFILTER_DEBUG is not set
-
-#
-# IP: Netfilter Configuration
+# Network device support
 #
-# CONFIG_IP_NF_CONNTRACK is not set
-# CONFIG_IP_NF_CONNTRACK_MARK is not set
-# CONFIG_IP_NF_QUEUE is not set
-# CONFIG_IP_NF_IPTABLES is not set
-CONFIG_IP_NF_ARPTABLES=y
-# CONFIG_IP_NF_ARPFILTER is not set
-# CONFIG_IP_NF_ARP_MANGLE is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-# CONFIG_NET_CLS_ROUTE is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
 CONFIG_NETDEVICES=y
 CONFIG_DUMMY=y
 # CONFIG_BONDING is not set
@@ -555,6 +557,8 @@ CONFIG_TIGON3=y
 # CONFIG_NET_FC is not set
 # CONFIG_SHAPER is not set
 # CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
 
 #
 # ISDN subsystem
@@ -659,6 +663,7 @@ CONFIG_DRM=y
 CONFIG_DRM_RADEON=y
 # CONFIG_DRM_MGA is not set
 # CONFIG_DRM_SIS is not set
+# CONFIG_DRM_VIA is not set
 # CONFIG_RAW_DRIVER is not set
 # CONFIG_HPET is not set
 # CONFIG_HANGCHECK_TIMER is not set
@@ -706,47 +711,10 @@ CONFIG_I2C_ALGOPCF=y
 # CONFIG_I2C_VIAPRO is not set
 # CONFIG_I2C_VOODOO3 is not set
 # CONFIG_I2C_PCA_ISA is not set
+# CONFIG_I2C_SENSOR is not set
 
 #
-# Hardware Sensors Chip support
-#
-# CONFIG_I2C_SENSOR is not set
-# CONFIG_SENSORS_ADM1021 is not set
-# CONFIG_SENSORS_ADM1025 is not set
-# CONFIG_SENSORS_ADM1026 is not set
-# CONFIG_SENSORS_ADM1031 is not set
-# CONFIG_SENSORS_ADM9240 is not set
-# CONFIG_SENSORS_ASB100 is not set
-# CONFIG_SENSORS_ATXP1 is not set
-# CONFIG_SENSORS_DS1621 is not set
-# CONFIG_SENSORS_FSCHER is not set
-# CONFIG_SENSORS_FSCPOS is not set
-# CONFIG_SENSORS_GL518SM is not set
-# CONFIG_SENSORS_GL520SM is not set
-# CONFIG_SENSORS_IT87 is not set
-# CONFIG_SENSORS_LM63 is not set
-# CONFIG_SENSORS_LM75 is not set
-# CONFIG_SENSORS_LM77 is not set
-# CONFIG_SENSORS_LM78 is not set
-# CONFIG_SENSORS_LM80 is not set
-# CONFIG_SENSORS_LM83 is not set
-# CONFIG_SENSORS_LM85 is not set
-# CONFIG_SENSORS_LM87 is not set
-# CONFIG_SENSORS_LM90 is not set
-# CONFIG_SENSORS_LM92 is not set
-# CONFIG_SENSORS_MAX1619 is not set
-# CONFIG_SENSORS_PC87360 is not set
-# CONFIG_SENSORS_SMSC47B397 is not set
-# CONFIG_SENSORS_SIS5595 is not set
-# CONFIG_SENSORS_SMSC47M1 is not set
-# CONFIG_SENSORS_VIA686A is not set
-# CONFIG_SENSORS_W83781D is not set
-# CONFIG_SENSORS_W83L785TS is not set
-# CONFIG_SENSORS_W83627HF is not set
-# CONFIG_SENSORS_W83627EHF is not set
-
-#
-# Other I2C Chip support
+# Miscellaneous I2C Chip support
 #
 # CONFIG_SENSORS_DS1337 is not set
 # CONFIG_SENSORS_DS1374 is not set
@@ -766,6 +734,11 @@ CONFIG_I2C_ALGOPCF=y
 #
 # CONFIG_W1 is not set
 
+#
+# Hardware Monitoring support
+#
+# CONFIG_HWMON is not set
+
 #
 # Misc devices
 #
@@ -782,7 +755,6 @@ CONFIG_VIDEO_DEV=y
 #
 # Video Adapters
 #
-# CONFIG_TUNER_MULTI_I2C is not set
 # CONFIG_VIDEO_BT848 is not set
 # CONFIG_VIDEO_CPIA is not set
 # CONFIG_VIDEO_SAA5246A is not set
@@ -1025,6 +997,7 @@ CONFIG_USB_HIDDEV=y
 # CONFIG_USB_EGALAX is not set
 # CONFIG_USB_XPAD is not set
 # CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_KEYSPAN_REMOTE is not set
 
 #
 # USB Imaging devices
@@ -1080,6 +1053,7 @@ CONFIG_USB_MON=y
 # CONFIG_USB_PHIDGETSERVO is not set
 # CONFIG_USB_IDMOUSE is not set
 # CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
 
 #
 # USB DSL modem support
@@ -1121,6 +1095,7 @@ CONFIG_JBD=y
 CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
 
 #
 # XFS support
@@ -1128,6 +1103,7 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_XFS_FS is not set
 # CONFIG_MINIX_FS is not set
 # CONFIG_ROMFS_FS is not set
+# CONFIG_INOTIFY is not set
 # CONFIG_QUOTA is not set
 CONFIG_DNOTIFY=y
 CONFIG_AUTOFS_FS=y

arch/ia64/hp/sim/boot/boot_head.S

@@ -22,7 +22,7 @@ GLOBAL_ENTRY(_start)
 	.save rp, r0
 	.body
 	movl gp = __gp
-	movl sp = stack_mem
+	movl sp = stack_mem+16384-16
 	bsw.1
 	br.call.sptk.many rp=start_bootloader
 END(_start)

arch/ia64/kernel/domain.c

@@ -341,7 +341,7 @@ next_sg:
 #endif
 
 	/* Attach the domains */
-	for_each_online_cpu(i) {
+	for_each_cpu_mask(i, *cpu_map) {
 		struct sched_domain *sd;
 #ifdef CONFIG_SCHED_SMT
 		sd = &per_cpu(cpu_domains, i);

arch/ia64/kernel/perfmon.c

@@ -4312,6 +4312,7 @@ pfm_context_load(pfm_context_t *ctx, void *arg, int count, struct pt_regs *regs)
 	DPRINT(("before cmpxchg() old_ctx=%p new_ctx=%p\n",
 		thread->pfm_context, ctx));
 
+	ret = -EBUSY;
 	old = ia64_cmpxchg(acq, &thread->pfm_context, NULL, ctx, sizeof(pfm_context_t *));
 	if (old != NULL) {
 		DPRINT(("load_pid [%d] already has a context\n", req->load_pid));

arch/ia64/kernel/salinfo.c

@@ -143,7 +143,8 @@ struct salinfo_data {
 
 static struct salinfo_data salinfo_data[ARRAY_SIZE(salinfo_log_name)];
 
-static spinlock_t data_lock, data_saved_lock;
+static DEFINE_SPINLOCK(data_lock);
+static DEFINE_SPINLOCK(data_saved_lock);
 
 /** salinfo_platform_oemdata - optional callback to decode oemdata from an error
  * record.

arch/ia64/kernel/signal.c

@@ -467,15 +467,12 @@ handle_signal (unsigned long sig, struct k_sigaction *ka, siginfo_t *info, sigse
 		if (!setup_frame(sig, ka, info, oldset, scr))
 			return 0;
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		{
-			sigorsets(&current->blocked, &current->blocked, &ka->sa.sa_mask);
-			sigaddset(&current->blocked, sig);
-			recalc_sigpending();
-		}
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked, &current->blocked, &ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
+		sigaddset(&current->blocked, sig);
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 	return 1;
 }
 

arch/ia64/pci/pci.c

@@ -380,6 +380,7 @@ void pcibios_bus_to_resource(struct pci_dev *dev,
 	res->start = region->start + offset;
 	res->end = region->end + offset;
 }
+EXPORT_SYMBOL(pcibios_bus_to_resource);
 
 static int __devinit is_valid_resource(struct pci_dev *dev, int idx)
 {

arch/ia64/sn/kernel/io_init.c

@@ -203,6 +203,7 @@ static void sn_fixup_ionodes(void)
 				continue;
 			}
 
+			spin_lock_init(&sn_flush_device_list->sfdl_flush_lock);
 			hubdev->hdi_flush_nasid_list.widget_p[widget] =
 			    sn_flush_device_list;
 		}
@@ -322,7 +323,7 @@ void sn_pci_controller_fixup(int segment, int busnum, struct pci_bus *bus)
 	struct pci_controller *controller;
 	struct pcibus_bussoft *prom_bussoft_ptr;
 	struct hubdev_info *hubdev_info;
-	void *provider_soft;
+	void *provider_soft = NULL;
 	struct sn_pcibus_provider *provider;
 
  	status = sal_get_pcibus_info((u64) segment, (u64) busnum,
@@ -338,7 +339,7 @@ void sn_pci_controller_fixup(int segment, int busnum, struct pci_bus *bus)
 	if (bus == NULL) {
  		bus = pci_scan_bus(busnum, &pci_root_ops, controller);
  		if (bus == NULL)
- 			return;	/* error, or bus already scanned */
+ 			goto error_return; /* error, or bus already scanned */
  		bus->sysdata = NULL;
 	}
 
@@ -351,28 +352,30 @@ void sn_pci_controller_fixup(int segment, int busnum, struct pci_bus *bus)
 	 */
 
 	if (prom_bussoft_ptr->bs_asic_type >= PCIIO_ASIC_MAX_TYPES)
-		return;		/* unsupported asic type */
+		goto error_return; /* unsupported asic type */
 
 	if (prom_bussoft_ptr->bs_asic_type == PCIIO_ASIC_TYPE_PPB)
 		goto error_return; /* no further fixup necessary */
 
 	provider = sn_pci_provider[prom_bussoft_ptr->bs_asic_type];
 	if (provider == NULL)
-		return;		/* no provider registerd for this asic */
+		goto error_return; /* no provider registerd for this asic */
 
-	provider_soft = NULL;
+	bus->sysdata = controller;
 	if (provider->bus_fixup)
 		provider_soft = (*provider->bus_fixup) (prom_bussoft_ptr, controller);
 
-	if (provider_soft == NULL)
-		return;		/* fixup failed or not applicable */
+	if (provider_soft == NULL) {
+		/* fixup failed or not applicable */
+		bus->sysdata = NULL;
+		goto error_return;
+	}
 
 	/*
 	 * Generic bus fixup goes here.  Don't reference prom_bussoft_ptr
 	 * after this point.
 	 */
 
-	bus->sysdata = controller;
 	PCI_CONTROLLER(bus)->platform_data = provider_soft;
 	nasid = NASID_GET(SN_PCIBUS_BUSSOFT(bus)->bs_base);
 	cnode = nasid_to_cnodeid(nasid);

arch/m32r/Kconfig

@@ -269,7 +269,7 @@ config NR_CPUS
 # Common NUMA Features
 config NUMA
 	bool "Numa Memory Allocation Support"
-	depends on SMP
+	depends on SMP && BROKEN
 	default n
 
 # turning this on wastes a bunch of space.
@@ -286,6 +286,7 @@ menu "Bus options (PCI, PCMCIA, EISA, MCA, ISA)"
 
 config PCI
 	bool "PCI support"
+	depends on BROKEN
 	default n
 	help
 	  Find out whether you have a PCI motherboard. PCI is the name of a

arch/m32r/Kconfig.debug

@@ -20,7 +20,7 @@ config DEBUG_STACK_USAGE
 
 config DEBUG_PAGEALLOC
 	bool "Page alloc debugging"
-	depends on DEBUG_KERNEL
+	depends on DEBUG_KERNEL && BROKEN
 	help
 	  Unmap pages from the kernel linear mapping after free_pages().
 	  This results in a large slowdown, but helps to find certain types

arch/m32r/kernel/setup_m32700ut.c

@@ -30,9 +30,11 @@
 typedef struct {
 	unsigned long icucr;  /* ICU Control Register */
 } icu_data_t;
+static icu_data_t icu_data[M32700UT_NUM_CPU_IRQ];
+#else
+icu_data_t icu_data[M32700UT_NUM_CPU_IRQ];
 #endif /* CONFIG_SMP */
 
-static icu_data_t icu_data[M32700UT_NUM_CPU_IRQ];
 
 static void disable_m32700ut_irq(unsigned int irq)
 {

arch/m32r/kernel/setup_opsput.c

@@ -31,9 +31,11 @@
 typedef struct {
 	unsigned long icucr;  /* ICU Control Register */
 } icu_data_t;
+static icu_data_t icu_data[OPSPUT_NUM_CPU_IRQ];
+#else
+icu_data_t icu_data[OPSPUT_NUM_CPU_IRQ];
 #endif /* CONFIG_SMP */
 
-static icu_data_t icu_data[OPSPUT_NUM_CPU_IRQ];
 
 static void disable_opsput_irq(unsigned int irq)
 {

arch/m32r/kernel/signal.c

@@ -341,13 +341,12 @@ handle_signal(unsigned long sig, struct k_sigaction *ka, siginfo_t *info,
 	/* Set up the stack frame */
 	setup_rt_frame(sig, ka, info, oldset, regs);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/m32r/kernel/smpboot.c

@@ -91,6 +91,7 @@ extern struct {
 
 /* which physical physical ID maps to which logical CPU number */
 static volatile int physid_2_cpu[NR_CPUS];
+#define physid_to_cpu(physid)	physid_2_cpu[physid]
 
 /* which logical CPU number maps to which physical ID */
 volatile int cpu_2_physid[NR_CPUS];

arch/m32r/lib/csum_partial_copy.c

@@ -58,3 +58,4 @@ csum_partial_copy_from_user (const unsigned char __user *src,
 	return csum_partial(dst, len-missing, sum);
 }
 EXPORT_SYMBOL(csum_partial_copy_from_user);
+EXPORT_SYMBOL(csum_partial);

arch/m32r/mm/discontig.c

@@ -12,12 +12,14 @@
 #include <linux/mmzone.h>
 #include <linux/initrd.h>
 #include <linux/nodemask.h>
+#include <linux/module.h>
 
 #include <asm/setup.h>
 
 extern char _end[];
 
 struct pglist_data *node_data[MAX_NUMNODES];
+EXPORT_SYMBOL(node_data);
 static bootmem_data_t node_bdata[MAX_NUMNODES] __initdata;
 
 pg_data_t m32r_node_data[MAX_NUMNODES];

arch/m68knommu/kernel/signal.c

@@ -732,13 +732,12 @@ handle_signal(int sig, struct k_sigaction *ka, siginfo_t *info,
 	if (ka->sa.sa_flags & SA_ONESHOT)
 		ka->sa.sa_handler = SIG_DFL;
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/mips/kernel/irixsig.c

@@ -155,13 +155,12 @@ static inline void handle_signal(unsigned long sig, siginfo_t *info,
 	else
 		setup_irix_frame(ka, regs, sig, oldset);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 asmlinkage int do_irix_signal(sigset_t *oldset, struct pt_regs *regs)

arch/mips/kernel/signal.c

@@ -425,13 +425,12 @@ static inline void handle_signal(unsigned long sig, siginfo_t *info,
 		setup_frame(ka, regs, sig, oldset);
 #endif
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 extern int do_signal32(sigset_t *oldset, struct pt_regs *regs);

arch/mips/kernel/signal32.c

@@ -751,13 +751,12 @@ static inline void handle_signal(unsigned long sig, siginfo_t *info,
 	else
 		setup_frame(ka, regs, sig, oldset);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 int do_signal32(sigset_t *oldset, struct pt_regs *regs)

arch/parisc/kernel/signal.c

@@ -517,13 +517,12 @@ handle_signal(unsigned long sig, siginfo_t *info, struct k_sigaction *ka,
 	if (!setup_rt_frame(sig, ka, info, oldset, regs, in_syscall))
 		return 0;
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 	return 1;
 }
 

arch/ppc/Kconfig

@@ -911,6 +911,7 @@ config PPCBUG_NVRAM
 	default y if PPC_PREP
 
 config SMP
+	depends on PPC_STD_MMU
 	bool "Symmetric multi-processing support"
 	---help---
 	  This enables support for systems with more than one CPU. If you have
@@ -930,7 +931,7 @@ config SMP
 
 config IRQ_ALL_CPUS
 	bool "Distribute interrupts on all CPUs by default"
-	depends on SMP
+	depends on SMP && !MV64360
 	help
 	  This option gives the kernel permission to distribute IRQs across
 	  multiple CPUs.  Saying N here will route all IRQs to the first
@@ -1121,7 +1122,9 @@ config PROC_HARDWARE
 
 source "drivers/zorro/Kconfig"
 
+if !44x || BROKEN
 source kernel/power/Kconfig
+endif
 
 config SECCOMP
 	bool "Enable seccomp to safely compute untrusted bytecode"

arch/ppc/kernel/signal.c

@@ -759,13 +759,12 @@ int do_signal(sigset_t *oldset, struct pt_regs *regs)
 	else
 		handle_signal(signr, &ka, &info, oldset, regs, newsp);
 
-	if (!(ka.sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka.sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka.sa.sa_mask);
+	if (!(ka.sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked, signr);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 
 	return 1;
 }

arch/ppc/platforms/4xx/Kconfig

@@ -3,6 +3,11 @@ config 4xx
 	depends on 40x || 44x
 	default y
 
+config WANT_EARLY_SERIAL
+	bool
+	select SERIAL_8250
+	default n
+
 menu "IBM 4xx options"
 	depends on 4xx
 
@@ -18,6 +23,7 @@ config ASH
 
 config BUBINGA
 	bool "Bubinga"
+	select WANT_EARLY_SERIAL
 	help
 	  This option enables support for the IBM 405EP evaluation board.
 
@@ -70,21 +76,25 @@ choice
 
 config BAMBOO
 	bool "Bamboo"
+	select WANT_EARLY_SERIAL
 	help
 	  This option enables support for the IBM PPC440EP evaluation board.
 
 config EBONY
 	bool "Ebony"
+	select WANT_EARLY_SERIAL
 	help
 	  This option enables support for the IBM PPC440GP evaluation board.
 
 config LUAN
 	bool "Luan"
+	select WANT_EARLY_SERIAL
 	help
 	  This option enables support for the IBM PPC440SP evaluation board.
 
 config OCOTEA
 	bool "Ocotea"
+	select WANT_EARLY_SERIAL
 	help
 	  This option enables support for the IBM PPC440GX evaluation board.
 
@@ -230,10 +240,6 @@ config PPC_GEN550
 	depends on 4xx
 	default y
 
-config PM
-	bool "Power Management support (EXPERIMENTAL)"
-	depends on 4xx && EXPERIMENTAL
-
 choice
 	prompt "TTYS0 device and default console"
 	depends on 40x

arch/ppc/syslib/m8xx_setup.c

@@ -423,7 +423,7 @@ platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
 	ppc_md.find_end_of_memory	= m8xx_find_end_of_memory;
 	ppc_md.setup_io_mappings	= m8xx_map_io;
 
-#if defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE)
+#if defined(CONFIG_BLK_DEV_MPC8xx_IDE)
 	m8xx_ide_init();
 #endif
 }

arch/ppc/syslib/ppc4xx_dma.c

@@ -620,6 +620,7 @@ ppc4xx_clr_dma_status(unsigned int dmanr)
 	return DMA_STATUS_GOOD;
 }
 
+#ifdef CONFIG_PPC4xx_EDMA
 /*
  * Enables the burst on the channel (BTEN bit in the control/count register)
  * Note:
@@ -685,6 +686,11 @@ ppc4xx_set_burst_size(unsigned int dmanr, unsigned int bsize)
 	return DMA_STATUS_GOOD;
 }
 
+EXPORT_SYMBOL(ppc4xx_enable_burst);
+EXPORT_SYMBOL(ppc4xx_disable_burst);
+EXPORT_SYMBOL(ppc4xx_set_burst_size);
+#endif /* CONFIG_PPC4xx_EDMA */
+
 EXPORT_SYMBOL(ppc4xx_init_dma_channel);
 EXPORT_SYMBOL(ppc4xx_get_channel_config);
 EXPORT_SYMBOL(ppc4xx_set_channel_priority);
@@ -703,6 +709,4 @@ EXPORT_SYMBOL(ppc4xx_enable_dma_interrupt);
 EXPORT_SYMBOL(ppc4xx_disable_dma_interrupt);
 EXPORT_SYMBOL(ppc4xx_get_dma_status);
 EXPORT_SYMBOL(ppc4xx_clr_dma_status);
-EXPORT_SYMBOL(ppc4xx_enable_burst);
-EXPORT_SYMBOL(ppc4xx_disable_burst);
-EXPORT_SYMBOL(ppc4xx_set_burst_size);
+

arch/ppc64/kernel/LparData.c

@@ -32,32 +32,12 @@
 /* The HvReleaseData is the root of the information shared between 
  * the hypervisor and Linux.  
  */
-
-/*
- * WARNING - magic here
- *
- * Ok, this is a horrid hack below, but marginally better than the
- * alternatives.  What we really want is just to initialize
- * hvReleaseData in C as in the #if 0 section here.  However, gcc
- * refuses to believe that (u32)&x is a constant expression, so will
- * not allow the xMsNucDataOffset field to be properly initialized.
- * So, we declare hvReleaseData in inline asm instead.  We use inline
- * asm, rather than a .S file, because the assembler won't generate
- * the necessary relocation for the LparMap either, unless that symbol
- * is declared in the same source file.  Finally, we put the asm in a
- * dummy, attribute-used function, instead of at file scope, because
- * file scope asms don't allow contraints.  We want to use the "i"
- * constraints to put sizeof() and offsetof() expressions in there,
- * because including asm/offsets.h in C code then stringifying causes
- * all manner of warnings.
- */
-#if 0
 struct HvReleaseData hvReleaseData = {
 	.xDesc = 0xc8a5d9c4,	/* "HvRD" ebcdic */
 	.xSize = sizeof(struct HvReleaseData),
 	.xVpdAreasPtrOffset = offsetof(struct naca_struct, xItVpdAreas),
 	.xSlicNacaAddr = &naca,		/* 64-bit Naca address */
-	.xMsNucDataOffset = (u32)((unsigned long)&xLparMap - KERNELBASE),
+	.xMsNucDataOffset = LPARMAP_PHYS,
 	.xFlags = HVREL_TAGSINACTIVE	/* tags inactive       */
 					/* 64 bit              */
 					/* shared processors   */
@@ -70,63 +50,6 @@ struct HvReleaseData hvReleaseData = {
 		0xa7, 0x40, 0xf2, 0x4b,
 		0xf4, 0x4b, 0xf6, 0xf4 },
 };
-#endif
-
-
-extern struct HvReleaseData hvReleaseData;
-
-static void __attribute_used__ hvReleaseData_wrapper(void)
-{
-	/* This doesn't appear to need any alignment (even 4 byte) */
-	asm volatile (
-		"	lparMapPhys = xLparMap - %3\n"
-		"	.data\n"
-		"	.globl	hvReleaseData\n"
-		"hvReleaseData:\n"
-		"	.long	0xc8a5d9c4\n"	/* xDesc */
-						/* "HvRD" in ebcdic */
-		"	.short	%0\n"		/* xSize */
-		"	.short	%1\n"		/* xVpdAreasPtrOffset */
-		"	.llong	naca\n"		/* xSlicNacaAddr */
-		"	.long	lparMapPhys\n"	/* xMsNucDataOffset */
-		"	.long	0\n"		/* xRsvd1 */
-		"	.short	%2\n"		/* xFlags */
-		"	.short	4\n"	/* xVrmIndex  - v5r2m0 */
-		"	.short	3\n"	/* xMinSupportedPlicVrmIndex - v5r1m0 */
-		"	.short	3\n"	/* xMinCompatablePlicVrmIndex - v5r1m0 */
-		"	.long	0xd38995a4\n"	/* xVrmName */
-		"	.long	0xa740f24b\n"	/*   "Linux 2.4.64" ebcdic */
-		"	.long	0xf44bf6f4\n"
-		"	. = hvReleaseData + %0\n"
-		"	.previous\n"
-		: : "i"(sizeof(hvReleaseData)),
-		"i"(offsetof(struct naca_struct, xItVpdAreas)),
-		"i"(HVREL_TAGSINACTIVE /* tags inactive, 64 bit, */
-				       /* shared processors, HMT allowed */
-		    | 6), /* TEMP: This allows non-GA drivers */
-		"i"(KERNELBASE)
-		);
-}
-
-struct LparMap __attribute__((aligned (16))) xLparMap = {
-	.xNumberEsids = HvEsidsToMap,
-	.xNumberRanges = HvRangesToMap,
-	.xSegmentTableOffs = STAB0_PAGE,
-
-	.xEsids = {
-		{ .xKernelEsid = GET_ESID(KERNELBASE),
-		  .xKernelVsid = KERNEL_VSID(KERNELBASE), },
-		{ .xKernelEsid = GET_ESID(VMALLOCBASE),
-		  .xKernelVsid = KERNEL_VSID(VMALLOCBASE), },
-	},
-
-	.xRanges = {
-		{ .xPages = HvPagesToMap,
-		  .xOffset = 0,
-		  .xVPN = KERNEL_VSID(KERNELBASE) << (SID_SHIFT - PAGE_SHIFT),
-		},
-	},
-};
 
 extern void system_reset_iSeries(void);
 extern void machine_check_iSeries(void);

arch/ppc64/kernel/Makefile

@@ -73,3 +73,8 @@ obj-$(CONFIG_ALTIVEC)		+= vecemu.o vector.o
 obj-$(CONFIG_KPROBES)		+= kprobes.o
 
 CFLAGS_ioctl32.o += -Ifs/
+
+ifeq ($(CONFIG_PPC_ISERIES),y)
+arch/ppc64/kernel/head.o: arch/ppc64/kernel/lparmap.s
+AFLAGS_head.o += -Iarch/ppc64/kernel
+endif

arch/ppc64/kernel/head.S

@@ -38,6 +38,7 @@
 #include <asm/cputable.h>
 #include <asm/setup.h>
 #include <asm/hvcall.h>
+#include <asm/iSeries/LparMap.h>
 
 #ifdef CONFIG_PPC_ISERIES
 #define DO_SOFT_DISABLE
@@ -679,6 +680,11 @@ hardware_interrupt_iSeries_masked:
 	.globl fwnmi_data_area
 fwnmi_data_area:
 
+#ifdef CONFIG_PPC_ISERIES
+	. = LPARMAP_PHYS
+#include "lparmap.s"
+#endif /* CONFIG_PPC_ISERIES */
+
 /*
  * Vectors for the FWNMI option.  Share common code.
  */

arch/ppc64/kernel/iommu.c

@@ -242,7 +242,7 @@ int iommu_map_sg(struct device *dev, struct iommu_table *tbl,
 	dma_addr_t dma_next = 0, dma_addr;
 	unsigned long flags;
 	struct scatterlist *s, *outs, *segstart;
-	int outcount;
+	int outcount, incount;
 	unsigned long handle;
 
 	BUG_ON(direction == DMA_NONE);
@@ -252,6 +252,7 @@ int iommu_map_sg(struct device *dev, struct iommu_table *tbl,
 
 	outs = s = segstart = &sglist[0];
 	outcount = 1;
+	incount = nelems;
 	handle = 0;
 
 	/* Init first segment length for backout at failure */
@@ -338,10 +339,10 @@ int iommu_map_sg(struct device *dev, struct iommu_table *tbl,
 
 	DBG("mapped %d elements:\n", outcount);
 
-	/* For the sake of iommu_free_sg, we clear out the length in the
+	/* For the sake of iommu_unmap_sg, we clear out the length in the
 	 * next entry of the sglist if we didn't fill the list completely
 	 */
-	if (outcount < nelems) {
+	if (outcount < incount) {
 		outs++;
 		outs->dma_address = DMA_ERROR_CODE;
 		outs->dma_length = 0;

arch/ppc64/kernel/lparmap.c

@@ -0,0 +1,31 @@
+/*
+ * Copyright (C) 2005  Stephen Rothwell  IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <asm/mmu.h>
+#include <asm/page.h>
+#include <asm/iSeries/LparMap.h>
+
+const struct LparMap __attribute__((__section__(".text"))) xLparMap = {
+	.xNumberEsids = HvEsidsToMap,
+	.xNumberRanges = HvRangesToMap,
+	.xSegmentTableOffs = STAB0_PAGE,
+
+	.xEsids = {
+		{ .xKernelEsid = GET_ESID(KERNELBASE),
+		  .xKernelVsid = KERNEL_VSID(KERNELBASE), },
+		{ .xKernelEsid = GET_ESID(VMALLOCBASE),
+		  .xKernelVsid = KERNEL_VSID(VMALLOCBASE), },
+	},
+
+	.xRanges = {
+		{ .xPages = HvPagesToMap,
+		  .xOffset = 0,
+		  .xVPN = KERNEL_VSID(KERNELBASE) << (SID_SHIFT - PAGE_SHIFT),
+		},
+	},
+};

arch/ppc64/kernel/prom_init.c

@@ -1803,7 +1803,7 @@ static void __init fixup_device_tree(void)
 	if (prom_getprop(u3, "device-rev", &u3_rev, sizeof(u3_rev))
 	    == PROM_ERROR)
 		return;
-	if (u3_rev != 0x35)
+	if (u3_rev != 0x35 && u3_rev != 0x37)
 		return;
 	/* does it need fixup ? */
 	if (prom_getproplen(i2c, "interrupts") > 0)

arch/ppc64/kernel/setup.c

@@ -706,6 +706,8 @@ void machine_power_off(void)
 	local_irq_disable();
 	while (1) ;
 }
+/* Used by the G5 thermal driver */
+EXPORT_SYMBOL_GPL(machine_power_off);
 
 void machine_halt(void)
 {

arch/ppc64/kernel/signal.c

@@ -481,10 +481,11 @@ static int handle_signal(unsigned long sig, struct k_sigaction *ka,
 	/* Set up Signal Frame */
 	ret = setup_rt_frame(sig, ka, info, oldset, regs);
 
-	if (ret && !(ka->sa.sa_flags & SA_NODEFER)) {
+	if (ret) {
 		spin_lock_irq(&current->sighand->siglock);
 		sigorsets(&current->blocked, &current->blocked, &ka->sa.sa_mask);
-		sigaddset(&current->blocked,sig);
+		if (!(ka->sa.sa_flags & SA_NODEFER))
+			sigaddset(&current->blocked,sig);
 		recalc_sigpending();
 		spin_unlock_irq(&current->sighand->siglock);
 	}

arch/ppc64/kernel/signal32.c

@@ -976,11 +976,12 @@ int do_signal32(sigset_t *oldset, struct pt_regs *regs)
 	else
 		ret = handle_signal32(signr, &ka, &info, oldset, regs, newsp);
 
-	if (ret && !(ka.sa.sa_flags & SA_NODEFER)) {
+	if (ret) {
 		spin_lock_irq(&current->sighand->siglock);
 		sigorsets(&current->blocked, &current->blocked,
 			  &ka.sa.sa_mask);
-		sigaddset(&current->blocked, signr);
+		if (!(ka.sa.sa_flags & SA_NODEFER))
+			sigaddset(&current->blocked, signr);
 		recalc_sigpending();
 		spin_unlock_irq(&current->sighand->siglock);
 	}

arch/s390/kernel/compat_signal.c

@@ -637,12 +637,11 @@ handle_signal32(unsigned long sig, struct k_sigaction *ka,
 	else
 		setup_frame32(sig, ka, oldset, regs);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 

arch/s390/kernel/cpcmd.c

@@ -46,9 +46,9 @@ int  __cpcmd(const char *cmd, char *response, int rlen, int *response_code)
 				"lra	3,0(%4)\n"
 				"lr	5,%5\n"
 				"diag	2,4,0x8\n"
-				"brc	8, .Litfits\n"
+				"brc	8, 1f\n"
 				"ar	5, %5\n"
-				".Litfits: \n"
+				"1: \n"
 				"lr	%0,4\n"
 				"lr	%1,5\n"
 				: "=d" (return_code), "=d" (return_len)
@@ -64,9 +64,9 @@ int  __cpcmd(const char *cmd, char *response, int rlen, int *response_code)
 				"sam31\n"
 				"diag	2,4,0x8\n"
 				"sam64\n"
-				"brc	8, .Litfits\n"
+				"brc	8, 1f\n"
 				"agr	5, %5\n"
-				".Litfits: \n"
+				"1: \n"
 				"lgr	%0,4\n"
 				"lgr	%1,5\n"
 				: "=d" (return_code), "=d" (return_len)

arch/s390/kernel/signal.c

@@ -429,13 +429,12 @@ handle_signal(unsigned long sig, struct k_sigaction *ka,
 	else
 		setup_frame(sig, ka, oldset, regs);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/sh/kernel/entry.S

@@ -1145,5 +1145,10 @@ ENTRY(sys_call_table)
 	.long sys_add_key		/* 285 */
 	.long sys_request_key
 	.long sys_keyctl
+	.long sys_ioprio_set
+	.long sys_ioprio_get
+	.long sys_inotify_init		/* 290 */
+	.long sys_inotify_add_watch
+	.long sys_inotify_rm_watch
 
 /* End of entry.S */

arch/sh/kernel/signal.c

@@ -546,13 +546,12 @@ handle_signal(unsigned long sig, struct k_sigaction *ka, siginfo_t *info,
 	if (ka->sa.sa_flags & SA_ONESHOT)
 		ka->sa.sa_handler = SIG_DFL;
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/sh64/kernel/signal.c

@@ -664,13 +664,12 @@ handle_signal(unsigned long sig, siginfo_t *info, struct k_sigaction *ka,
 	else
 		setup_frame(sig, ka, oldset, regs);
 
-	if (!(ka->sa.sa_flags & SA_NODEFER)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NODEFER))
 		sigaddset(&current->blocked,sig);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 /*

arch/sh64/kernel/syscalls.S

@@ -342,4 +342,9 @@ sys_call_table:
 	.long sys_add_key
 	.long sys_request_key
 	.long sys_keyctl		/* 315 */
+	.long sys_ioprio_set
+	.long sys_ioprio_get
+	.long sys_inotify_init
+	.long sys_inotify_add_watch
+	.long sys_inotify_rm_watch	/* 320 */
 

arch/sparc/kernel/setup.c

@@ -32,7 +32,6 @@
 #include <linux/spinlock.h>
 #include <linux/root_dev.h>
 
-#include <asm/segment.h>
 #include <asm/system.h>
 #include <asm/io.h>
 #include <asm/processor.h>

arch/sparc/kernel/signal.c

@@ -1034,13 +1034,12 @@ handle_signal(unsigned long signr, struct k_sigaction *ka,
 		else
 			setup_frame(&ka->sa, regs, signr, oldset, info);
 	}
-	if (!(ka->sa.sa_flags & SA_NOMASK)) {
-		spin_lock_irq(&current->sighand->siglock);
-		sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	spin_lock_irq(&current->sighand->siglock);
+	sigorsets(&current->blocked,&current->blocked,&ka->sa.sa_mask);
+	if (!(ka->sa.sa_flags & SA_NOMASK))
 		sigaddset(&current->blocked, signr);
-		recalc_sigpending();
-		spin_unlock_irq(&current->sighand->siglock);
-	}
+	recalc_sigpending();
+	spin_unlock_irq(&current->sighand->siglock);
 }
 
 static inline void syscall_restart(unsigned long orig_i0, struct pt_regs *regs,

arch/sparc/kernel/sparc_ksyms.c

@@ -98,8 +98,9 @@ extern void ___rw_write_enter(void);
  * The module references will be fixed up by module_frob_arch_sections.
  */
 #define DOT_ALIAS2(__ret, __x, __arg1, __arg2) \
-	extern __ret __x(__arg1, __arg2) \
-	             __attribute__((weak, alias("." # __x)));
+	extern __ret __x(__arg1, __arg2); \
+	asm(".weak " #__x);\
+	asm(#__x "=." #__x);
 
 DOT_ALIAS2(int, div, int, int)
 DOT_ALIAS2(int, mul, int, int)

arch/sparc/kernel/tick14.c

@@ -19,7 +19,6 @@
 #include <linux/interrupt.h>
 
 #include <asm/oplib.h>
-#include <asm/segment.h>
 #include <asm/timer.h>
 #include <asm/mostek.h>
 #include <asm/system.h>

arch/sparc/kernel/time.c

@@ -32,7 +32,6 @@
 #include <linux/profile.h>
 
 #include <asm/oplib.h>
-#include <asm/segment.h>
 #include <asm/timer.h>
 #include <asm/mostek.h>
 #include <asm/system.h>

arch/sparc/mm/fault.c

@@ -23,7 +23,6 @@
 #include <linux/module.h>
 
 #include <asm/system.h>
-#include <asm/segment.h>
 #include <asm/page.h>
 #include <asm/pgtable.h>
 #include <asm/memreg.h>

arch/sparc/mm/init.c

@@ -25,7 +25,6 @@
 #include <linux/bootmem.h>
 
 #include <asm/system.h>
-#include <asm/segment.h>
 #include <asm/vac-ops.h>
 #include <asm/page.h>
 #include <asm/pgtable.h>

arch/sparc64/kernel/Makefile

@@ -8,7 +8,7 @@ EXTRA_CFLAGS := -Werror
 extra-y		:= head.o init_task.o vmlinux.lds
 
 obj-y		:= process.o setup.o cpu.o idprom.o \
-		   traps.o devices.o auxio.o \
+		   traps.o devices.o auxio.o una_asm.o \
 		   irq.o ptrace.o time.o sys_sparc.o signal.o \
 		   unaligned.o central.o pci.o starfire.o semaphore.o \
 		   power.o sbus.o iommu_common.o sparc64_ksyms.o chmc.o