Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (103 commits)
  ARM: 5719/1: [AT91] Fix AC97 breakage
  ARM: 5721/1: MMCI enable the use of a regulator
  ARM: 5720/1: Move MMCI header to amba include dir
  ARM: 5718/1: Sane busids for RealView board components
  ARM: 5715/1: Make kprobes unregistration SMP safe
  ARM: 5711/1: locomo.c: CodingStyle cleanups
  ARM: 5710/1: at91: add AC97 support to at91sam9rl and at91sam9rlek board
  ARM: 5709/1: at91: add AC97 support to at91sam9g45 series and at91sam9m10g45ek board
  ARM: 5621/1: at91/dmaengine: integration of at_hdmac driver in at91sam9g45 series
  ARM: 5620/1: at91/dmaengine: integration of at_hdmac driver in at91sam9rl
  ARM: Add support for checking access permissions on prefetch aborts
  ARM: Separate out access error checking
  ARM: Ensure correct might_sleep() check in pagefault path
  ARM: Update page fault handling for new OOM techniques
  ARM: Provide definitions and helpers for decoding the FSR register
  ARM: 5712/1: SA1100: initialise spinlock in DMA code
  ARM: s3c: fix check of index into s3c_gpios[]
  ARM: spitz: fix touchscreen max presure
  ARM: STMP3xxx: deallocation with negative index of descriptors[]
  Thumb-2: Correctly handle undefined instructions in the kernel
  ...

Documentation/arm/tcm.txt

@@ -0,0 +1,145 @@
+ARM TCM (Tightly-Coupled Memory) handling in Linux
+----
+Written by Linus Walleij <linus.walleij@stericsson.com>
+
+Some ARM SoC:s have a so-called TCM (Tightly-Coupled Memory).
+This is usually just a few (4-64) KiB of RAM inside the ARM
+processor.
+
+Due to being embedded inside the CPU The TCM has a
+Harvard-architecture, so there is an ITCM (instruction TCM)
+and a DTCM (data TCM). The DTCM can not contain any
+instructions, but the ITCM can actually contain data.
+The size of DTCM or ITCM is minimum 4KiB so the typical
+minimum configuration is 4KiB ITCM and 4KiB DTCM.
+
+ARM CPU:s have special registers to read out status, physical
+location and size of TCM memories. arch/arm/include/asm/cputype.h
+defines a CPUID_TCM register that you can read out from the
+system control coprocessor. Documentation from ARM can be found
+at http://infocenter.arm.com, search for "TCM Status Register"
+to see documents for all CPUs. Reading this register you can
+determine if ITCM (bit 0) and/or DTCM (bit 16) is present in the
+machine.
+
+There is further a TCM region register (search for "TCM Region
+Registers" at the ARM site) that can report and modify the location
+size of TCM memories at runtime. This is used to read out and modify
+TCM location and size. Notice that this is not a MMU table: you
+actually move the physical location of the TCM around. At the
+place you put it, it will mask any underlying RAM from the
+CPU so it is usually wise not to overlap any physical RAM with
+the TCM. The TCM memory exists totally outside the MMU and will
+override any MMU mappings.
+
+Code executing inside the ITCM does not "see" any MMU mappings
+and e.g. register accesses must be made to physical addresses.
+
+TCM is used for a few things:
+
+- FIQ and other interrupt handlers that need deterministic
+  timing and cannot wait for cache misses.
+
+- Idle loops where all external RAM is set to self-refresh
+  retention mode, so only on-chip RAM is accessible by
+  the CPU and then we hang inside ITCM waiting for an
+  interrupt.
+
+- Other operations which implies shutting off or reconfiguring
+  the external RAM controller.
+
+There is an interface for using TCM on the ARM architecture
+in <asm/tcm.h>. Using this interface it is possible to:
+
+- Define the physical address and size of ITCM and DTCM.
+
+- Tag functions to be compiled into ITCM.
+
+- Tag data and constants to be allocated to DTCM and ITCM.
+
+- Have the remaining TCM RAM added to a special
+  allocation pool with gen_pool_create() and gen_pool_add()
+  and provice tcm_alloc() and tcm_free() for this
+  memory. Such a heap is great for things like saving
+  device state when shutting off device power domains.
+
+A machine that has TCM memory shall select HAVE_TCM in
+arch/arm/Kconfig for itself, and then the
+rest of the functionality will depend on the physical
+location and size of ITCM and DTCM to be defined in
+mach/memory.h for the machine. Code that needs to use
+TCM shall #include <asm/tcm.h> If the TCM is not located
+at the place given in memory.h it will be moved using
+the TCM Region registers.
+
+Functions to go into itcm can be tagged like this:
+int __tcmfunc foo(int bar);
+
+Variables to go into dtcm can be tagged like this:
+int __tcmdata foo;
+
+Constants can be tagged like this:
+int __tcmconst foo;
+
+To put assembler into TCM just use
+.section ".tcm.text" or .section ".tcm.data"
+respectively.
+
+Example code:
+
+#include <asm/tcm.h>
+
+/* Uninitialized data */
+static u32 __tcmdata tcmvar;
+/* Initialized data */
+static u32 __tcmdata tcmassigned = 0x2BADBABEU;
+/* Constant */
+static const u32 __tcmconst tcmconst = 0xCAFEBABEU;
+
+static void __tcmlocalfunc tcm_to_tcm(void)
+{
+	int i;
+	for (i = 0; i < 100; i++)
+		tcmvar ++;
+}
+
+static void __tcmfunc hello_tcm(void)
+{
+	/* Some abstract code that runs in ITCM */
+	int i;
+	for (i = 0; i < 100; i++) {
+		tcmvar ++;
+	}
+	tcm_to_tcm();
+}
+
+static void __init test_tcm(void)
+{
+	u32 *tcmem;
+	int i;
+
+	hello_tcm();
+	printk("Hello TCM executed from ITCM RAM\n");
+
+	printk("TCM variable from testrun: %u @ %p\n", tcmvar, &tcmvar);
+	tcmvar = 0xDEADBEEFU;
+	printk("TCM variable: 0x%x @ %p\n", tcmvar, &tcmvar);
+
+	printk("TCM assigned variable: 0x%x @ %p\n", tcmassigned, &tcmassigned);
+
+	printk("TCM constant: 0x%x @ %p\n", tcmconst, &tcmconst);
+
+	/* Allocate some TCM memory from the pool */
+	tcmem = tcm_alloc(20);
+	if (tcmem) {
+		printk("TCM Allocated 20 bytes of TCM @ %p\n", tcmem);
+		tcmem[0] = 0xDEADBEEFU;
+		tcmem[1] = 0x2BADBABEU;
+		tcmem[2] = 0xCAFEBABEU;
+		tcmem[3] = 0xDEADBEEFU;
+		tcmem[4] = 0x2BADBABEU;
+		for (i = 0; i < 5; i++)
+			printk("TCM tcmem[%d] = %08x\n", i, tcmem[i]);
+		tcm_free(tcmem, 20);
+	}
+}

MAINTAINERS

@@ -683,7 +683,7 @@ S:	Maintained
 ARM/INTEL IXP4XX ARM ARCHITECTURE
 M:	Imre Kaloz <kaloz@openwrt.org>
 M:	Krzysztof Halasa <khc@pm.waw.pl>
-L:	linux-arm-kernel@lists.infradead.org
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-ixp4xx/
 
@@ -740,18 +740,22 @@ M:	Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
 M:	Dirk Opfer <dirk@opfer-online.de>
 S:	Maintained
 
-ARM/PALMTX,PALMT5,PALMLD,PALMTE2 SUPPORT
-M:	Marek Vasut <marek.vasut@gmail.com>
+ARM/PALMTX,PALMT5,PALMLD,PALMTE2,PALMTC SUPPORT
+P:	Marek Vasut
+M:	marek.vasut@gmail.com
+L:	linux-arm-kernel@lists.infradead.org
 W:	http://hackndev.com
 S:	Maintained
 
 ARM/PALM TREO 680 SUPPORT
 M:	Tomas Cech <sleep_walker@suse.cz>
+L:	linux-arm-kernel@lists.infradead.org
 W:	http://hackndev.com
 S:	Maintained
 
 ARM/PALMZ72 SUPPORT
 M:	Sergey Lapin <slapin@ossfans.org>
+L:	linux-arm-kernel@lists.infradead.org
 W:	http://hackndev.com
 S:	Maintained
 

arch/arm/Kconfig

@@ -46,6 +46,10 @@ config GENERIC_CLOCKEVENTS_BROADCAST
 	depends on GENERIC_CLOCKEVENTS
 	default y if SMP && !LOCAL_TIMERS
 
+config HAVE_TCM
+	bool
+	select GENERIC_ALLOCATOR
+
 config NO_IOPORT
 	bool
 
@@ -649,6 +653,7 @@ config ARCH_U300
 	bool "ST-Ericsson U300 Series"
 	depends on MMU
 	select CPU_ARM926T
+	select HAVE_TCM
 	select ARM_AMBA
 	select ARM_VIC
 	select GENERIC_TIME

arch/arm/common/locomo.c

@@ -865,6 +865,7 @@ void locomo_gpio_set_dir(struct device *dev, unsigned int bits, unsigned int dir
 
 	spin_unlock_irqrestore(&lchip->lock, flags);
 }
+EXPORT_SYMBOL(locomo_gpio_set_dir);
 
 int locomo_gpio_read_level(struct device *dev, unsigned int bits)
 {
@@ -882,6 +883,7 @@ int locomo_gpio_read_level(struct device *dev, unsigned int bits)
 	ret &= bits;
 	return ret;
 }
+EXPORT_SYMBOL(locomo_gpio_read_level);
 
 int locomo_gpio_read_output(struct device *dev, unsigned int bits)
 {
@@ -899,6 +901,7 @@ int locomo_gpio_read_output(struct device *dev, unsigned int bits)
 	ret &= bits;
 	return ret;
 }
+EXPORT_SYMBOL(locomo_gpio_read_output);
 
 void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set)
 {
@@ -920,6 +923,7 @@ void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set)
 
 	spin_unlock_irqrestore(&lchip->lock, flags);
 }
+EXPORT_SYMBOL(locomo_gpio_write);
 
 static void locomo_m62332_sendbit(void *mapbase, int bit)
 {
@@ -1084,13 +1088,12 @@ void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int
 
 	spin_unlock_irqrestore(&lchip->lock, flags);
 }
+EXPORT_SYMBOL(locomo_m62332_senddata);
 
 /*
  *	Frontlight control
  */
 
-static struct locomo *locomo_chip_driver(struct locomo_dev *ldev);
-
 void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf)
 {
 	unsigned long flags;
@@ -1182,11 +1185,13 @@ int locomo_driver_register(struct locomo_driver *driver)
 	driver->drv.bus = &locomo_bus_type;
 	return driver_register(&driver->drv);
 }
+EXPORT_SYMBOL(locomo_driver_register);
 
 void locomo_driver_unregister(struct locomo_driver *driver)
 {
 	driver_unregister(&driver->drv);
 }
+EXPORT_SYMBOL(locomo_driver_unregister);
 
 static int __init locomo_init(void)
 {
@@ -1208,11 +1213,3 @@ module_exit(locomo_exit);
 MODULE_DESCRIPTION("Sharp LoCoMo core driver");
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>");
-
-EXPORT_SYMBOL(locomo_driver_register);
-EXPORT_SYMBOL(locomo_driver_unregister);
-EXPORT_SYMBOL(locomo_gpio_set_dir);
-EXPORT_SYMBOL(locomo_gpio_read_level);
-EXPORT_SYMBOL(locomo_gpio_read_output);
-EXPORT_SYMBOL(locomo_gpio_write);
-EXPORT_SYMBOL(locomo_m62332_senddata);

arch/arm/common/vic.c

@@ -22,6 +22,7 @@
 #include <linux/list.h>
 #include <linux/io.h>
 #include <linux/sysdev.h>
+#include <linux/device.h>
 #include <linux/amba/bus.h>
 
 #include <asm/mach/irq.h>

arch/arm/configs/littleton_defconfig

@@ -1,783 +0,0 @@
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc5
-# Fri Dec 21 11:06:19 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_LOCK_KERNEL=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-# CONFIG_CPU_PXA320 is not set
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-# CONFIG_MACH_ZYLONITE is not set
-CONFIG_MACH_LITTLETON=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-CONFIG_PXA_SSP=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-CONFIG_TICK_ONESHOT=y
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_PREEMPT=y
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=64M"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# CPU Frequency scaling
-#
-# CONFIG_CPU_FREQ is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-# CONFIG_INET_LRO is not set
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_STANDALONE is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_FW_LOADER=y
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-# CONFIG_WATCHDOG is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-CONFIG_FONT_8x16=y
-# CONFIG_FONT_6x11 is not set
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-CONFIG_PRINTK_TIME=y
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_MAGIC_SYSRQ=y
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_SLAB is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_LOCK_ALLOC is not set
-# CONFIG_PROVE_LOCKING is not set
-# CONFIG_LOCK_STAT is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-CONFIG_FRAME_POINTER=y
-CONFIG_FORCED_INLINING=y
-# CONFIG_BOOT_PRINTK_DELAY is not set
-# CONFIG_RCU_TORTURE_TEST is not set
-# CONFIG_FAULT_INJECTION is not set
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
-# CONFIG_DEBUG_ICEDCC is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-CONFIG_CRYPTO_HW=y
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-CONFIG_CRC_CCITT=y
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y

arch/arm/configs/pxa3xx_defconfig

@@ -0,0 +1,1332 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc1
+# Mon Jul 13 22:48:49 2009
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+# CONFIG_CLASSIC_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=18
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+# CONFIG_MODULE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+
+#
+# Supported PXA3xx Processor Variants
+#
+CONFIG_CPU_PXA300=y
+CONFIG_CPU_PXA310=y
+CONFIG_CPU_PXA320=y
+CONFIG_CPU_PXA930=y
+CONFIG_CPU_PXA935=y
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+CONFIG_MACH_ZYLONITE=y
+CONFIG_MACH_LITTLETON=y
+CONFIG_MACH_TAVOREVB=y
+CONFIG_MACH_SAAR=y
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_PXA3xx=y
+CONFIG_PXA_SSP=y
+CONFIG_PXA_HAVE_BOARD_IRQS=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSC3=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_IO_36=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_OUTER_CACHE=y
+CONFIG_CACHE_XSC3L2=y
+CONFIG_IWMMXT=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PREEMPT=y
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=64M debug"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_H1900 is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_SHARPSL is not set
+CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_PXA3xx_BUILTIN=y
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_ONENAND=y
+CONFIG_MTD_ONENAND_VERIFY_WRITE=y
+CONFIG_MTD_ONENAND_GENERIC=y
+# CONFIG_MTD_ONENAND_OTP is not set
+# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
+# CONFIG_MTD_ONENAND_SIM is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+CONFIG_KEYBOARD_PXA27x=y
+CONFIG_KEYBOARD_PXA930_ROTARY=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
+CONFIG_MOUSE_PXA930_TRKBALL=y
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+CONFIG_TOUCHSCREEN_DA9034=y
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+# CONFIG_I2C_HELPER_AUTO is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=y
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_PXA2XX=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+CONFIG_GPIO_MAX732X=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_PCF857X=y
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+CONFIG_GPIO_MAX7301=y
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_SUPPLY_DEBUG=y
+CONFIG_PDA_POWER=y
+# CONFIG_BATTERY_DS2760 is not set
+# CONFIG_BATTERY_BQ27x00 is not set
+CONFIG_BATTERY_DA9030=y
+# CONFIG_BATTERY_MAX17040 is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+CONFIG_PMIC_DA903X=y
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_PXA=y
+# CONFIG_FB_PXA_OVERLAY is not set
+# CONFIG_FB_PXA_SMARTPANEL is not set
+# CONFIG_FB_PXA_PARAMETERS is not set
+# CONFIG_FB_MBX is not set
+# CONFIG_FB_W100 is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+CONFIG_LCD_TDO24M=y
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_BACKLIGHT_DA903X=y
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+CONFIG_FONTS=y
+# CONFIG_FONT_8x8 is not set
+# CONFIG_FONT_8x16 is not set
+CONFIG_FONT_6x11=y
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+# CONFIG_FONT_MINI_4x6 is not set
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_PXA=y
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=m
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_PCA955X is not set
+CONFIG_LEDS_DA903X=m
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_PWM is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+CONFIG_LEDS_TRIGGER_GPIO=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+CONFIG_REGULATOR_DA903X=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+# CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+# CONFIG_JFFS2_CMODE_NONE is not set
+CONFIG_JFFS2_CMODE_PRIORITY=y
+# CONFIG_JFFS2_CMODE_SIZE is not set
+# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=1
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+CONFIG_DEBUG_PREEMPT=y
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+CONFIG_DEBUG_SPINLOCK=y
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+CONFIG_DEBUG_SPINLOCK_SLEEP=y
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y

arch/arm/configs/xcep_defconfig

@@ -0,0 +1,1129 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc6
+# Thu Aug 20 09:02:37 2009
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=".xcep-itech"
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+# CONFIG_UID16 is not set
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+# CONFIG_SHMEM is not set
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_STRIP_ASM_SYMS=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_SLAB is not set
+# CONFIG_SLUB is not set
+CONFIG_SLOB=y
+# CONFIG_PROFILING is not set
+CONFIG_TRACEPOINTS=y
+CONFIG_MARKERS=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_KPROBES=y
+CONFIG_KRETPROBES=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLOCK is not set
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+# CONFIG_MACH_ZYLONITE is not set
+# CONFIG_MACH_LITTLETON is not set
+# CONFIG_MACH_TAVOREVB is not set
+# CONFIG_MACH_SAAR is not set
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_MACH_XCEP=y
+CONFIG_PXA25x=y
+CONFIG_PXA_SSP=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+CONFIG_IWMMXT=y
+CONFIG_XSCALE_PMU=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=mtd4 rootfstype=jffs2 ro console=ttyS0,115200"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=m
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_LRO=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_TCPPROBE is not set
+# CONFIG_NET_DROP_MONITOR is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_XIP is not set
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
+CONFIG_MTD_PXA2XX=y
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+
+#
+# SCSI device support
+#
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=m
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+# CONFIG_SPI is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=m
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+CONFIG_SENSORS_ADM1021=m
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+CONFIG_SENSORS_MAX6650=m
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_NEW_LEDS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=m
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_SA1100=m
+# CONFIG_RTC_DRV_PXA is not set
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_FILE_LOCKING=y
+# CONFIG_FSNOTIFY is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=m
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+CONFIG_NLS=m
+CONFIG_NLS_DEFAULT="utf8"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_KPROBES_SANITY_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_ARM_UNWIND is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=m
+CONFIG_CRYPTO_ALGAPI2=m
+CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=m
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y

arch/arm/configs/zylonite_defconfig

@@ -1,736 +0,0 @@
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23
-# Tue Oct 23 13:33:20 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=18
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLUB_DEBUG=y
-# CONFIG_SLAB is not set
-CONFIG_SLUB=y
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-# CONFIG_MODULE_UNLOAD is not set
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-CONFIG_CPU_PXA320=y
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-CONFIG_MACH_ZYLONITE=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-# CONFIG_TICK_ONESHOT is not set
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-# CONFIG_PREEMPT is not set
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfs/rootfs/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,38400 mem=64M debug"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=y
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-# CONFIG_FONT_8x16 is not set
-CONFIG_FONT_6x11=y
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-# CONFIG_SLUB_DEBUG_ON is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_FRAME_POINTER=y
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-# CONFIG_CRYPTO_HW is not set
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y

arch/arm/include/asm/atomic.h

@@ -19,31 +19,21 @@
 
 #ifdef __KERNEL__
 
+/*
+ * On ARM, ordinary assignment (str instruction) doesn't clear the local
+ * strex/ldrex monitor on some implementations. The reason we can use it for
+ * atomic_set() is the clrex or dummy strex done on every exception return.
+ */
 #define atomic_read(v)	((v)->counter)
+#define atomic_set(v,i)	(((v)->counter) = (i))
 
 #if __LINUX_ARM_ARCH__ >= 6
 
 /*
  * ARMv6 UP and SMP safe atomic ops.  We use load exclusive and
  * store exclusive to ensure that these are atomic.  We may loop
- * to ensure that the update happens.  Writing to 'v->counter'
- * without using the following operations WILL break the atomic
- * nature of these ops.
+ * to ensure that the update happens.
  */
-static inline void atomic_set(atomic_t *v, int i)
-{
-	unsigned long tmp;
-
-	__asm__ __volatile__("@ atomic_set\n"
-"1:	ldrex	%0, [%1]\n"
-"	strex	%0, %2, [%1]\n"
-"	teq	%0, #0\n"
-"	bne	1b"
-	: "=&r" (tmp)
-	: "r" (&v->counter), "r" (i)
-	: "cc");
-}
-
 static inline void atomic_add(int i, atomic_t *v)
 {
 	unsigned long tmp;
@@ -163,8 +153,6 @@ static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr)
 #error SMP not supported on pre-ARMv6 CPUs
 #endif
 
-#define atomic_set(v,i)	(((v)->counter) = (i))
-
 static inline int atomic_add_return(int i, atomic_t *v)
 {
 	unsigned long flags;

arch/arm/include/asm/cache.h

@@ -4,7 +4,7 @@
 #ifndef __ASMARM_CACHE_H
 #define __ASMARM_CACHE_H
 
-#define L1_CACHE_SHIFT		5
+#define L1_CACHE_SHIFT		CONFIG_ARM_L1_CACHE_SHIFT
 #define L1_CACHE_BYTES		(1 << L1_CACHE_SHIFT)
 
 /*

arch/arm/include/asm/cputype.h

@@ -63,6 +63,11 @@ static inline unsigned int __attribute_const__ read_cpuid_cachetype(void)
 	return read_cpuid(CPUID_CACHETYPE);
 }
 
+static inline unsigned int __attribute_const__ read_cpuid_tcmstatus(void)
+{
+	return read_cpuid(CPUID_TCM);
+}
+
 /*
  * Intel's XScale3 core supports some v6 features (supersections, L2)
  * but advertises itself as v5 as it does not support the v6 ISA.  For
@@ -73,7 +78,10 @@ static inline unsigned int __attribute_const__ read_cpuid_cachetype(void)
 #else
 static inline int cpu_is_xsc3(void)
 {
-	if ((read_cpuid_id() & 0xffffe000) == 0x69056000)
+	unsigned int id;
+	id = read_cpuid_id() & 0xffffe000;
+	/* It covers both Intel ID and Marvell ID */
+	if ((id == 0x69056000) || (id == 0x56056000))
 		return 1;
 
 	return 0;

arch/arm/include/asm/tcm.h

@@ -0,0 +1,31 @@
+/*
+ *
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ *
+ */
+#ifndef __ASMARM_TCM_H
+#define __ASMARM_TCM_H
+
+#ifndef CONFIG_HAVE_TCM
+#error "You should not be including tcm.h unless you have a TCM!"
+#endif
+
+#include <linux/compiler.h>
+
+/* Tag variables with this */
+#define __tcmdata __section(.tcm.data)
+/* Tag constants with this */
+#define __tcmconst __section(.tcm.rodata)
+/* Tag functions inside TCM called from outside TCM with this */
+#define __tcmfunc __attribute__((long_call)) __section(.tcm.text) noinline
+/* Tag function inside TCM called from inside TCM  with this */
+#define __tcmlocalfunc __section(.tcm.text)
+
+void *tcm_alloc(size_t len);
+void tcm_free(void *addr, size_t len);
+
+#endif

arch/arm/include/asm/unified.h

@@ -35,7 +35,9 @@
 
 #define ARM(x...)
 #define THUMB(x...)	x
+#ifdef __ASSEMBLY__
 #define W(instr)	instr.w
+#endif
 #define BSYM(sym)	sym + 1
 
 #else	/* !CONFIG_THUMB2_KERNEL */
@@ -45,7 +47,9 @@
 
 #define ARM(x...)	x
 #define THUMB(x...)
+#ifdef __ASSEMBLY__
 #define W(instr)	instr
+#endif
 #define BSYM(sym)	sym
 
 #endif	/* CONFIG_THUMB2_KERNEL */

arch/arm/kernel/Makefile

@@ -35,6 +35,7 @@ obj-$(CONFIG_OABI_COMPAT)	+= sys_oabi-compat.o
 obj-$(CONFIG_ARM_THUMBEE)	+= thumbee.o
 obj-$(CONFIG_KGDB)		+= kgdb.o
 obj-$(CONFIG_ARM_UNWIND)	+= unwind.o
+obj-$(CONFIG_HAVE_TCM)		+= tcm.o
 
 obj-$(CONFIG_CRUNCH)		+= crunch.o crunch-bits.o
 AFLAGS_crunch-bits.o		:= -Wa,-mcpu=ep9312

arch/arm/kernel/entry-armv.S

@@ -272,7 +272,15 @@ __und_svc:
 	@
 	@  r0 - instruction
 	@
+#ifndef	CONFIG_THUMB2_KERNEL
 	ldr	r0, [r2, #-4]
+#else
+	ldrh	r0, [r2, #-2]			@ Thumb instruction at LR - 2
+	and	r9, r0, #0xf800
+	cmp	r9, #0xe800			@ 32-bit instruction if xx >= 0
+	ldrhhs	r9, [r2]			@ bottom 16 bits
+	orrhs	r0, r9, r0, lsl #16
+#endif
 	adr	r9, BSYM(1f)
 	bl	call_fpe
 
@@ -678,7 +686,9 @@ ENTRY(fp_enter)
 	.word	no_fp
 	.previous
 
-no_fp:	mov	pc, lr
+ENTRY(no_fp)
+	mov	pc, lr
+ENDPROC(no_fp)
 
 __und_usr_unknown:
 	enable_irq
@@ -734,13 +744,6 @@ ENTRY(__switch_to)
 #ifdef CONFIG_MMU
 	ldr	r6, [r2, #TI_CPU_DOMAIN]
 #endif
-#if __LINUX_ARM_ARCH__ >= 6
-#ifdef CONFIG_CPU_32v6K
-	clrex
-#else
-	strex	r5, r4, [ip]			@ Clear exclusive monitor
-#endif
-#endif
 #if defined(CONFIG_HAS_TLS_REG)
 	mcr	p15, 0, r3, c13, c0, 3		@ set TLS register
 #elif !defined(CONFIG_TLS_REG_EMUL)

arch/arm/kernel/entry-header.S

@@ -76,13 +76,25 @@
 #ifndef CONFIG_THUMB2_KERNEL
 	.macro	svc_exit, rpsr
 	msr	spsr_cxsf, \rpsr
+#if defined(CONFIG_CPU_32v6K)
+	clrex					@ clear the exclusive monitor
 	ldmia	sp, {r0 - pc}^			@ load r0 - pc, cpsr
+#elif defined (CONFIG_CPU_V6)
+	ldr	r0, [sp]
+	strex	r1, r2, [sp]			@ clear the exclusive monitor
+	ldmib	sp, {r1 - pc}^			@ load r1 - pc, cpsr
+#endif
 	.endm
 
 	.macro	restore_user_regs, fast = 0, offset = 0
 	ldr	r1, [sp, #\offset + S_PSR]	@ get calling cpsr
 	ldr	lr, [sp, #\offset + S_PC]!	@ get pc
 	msr	spsr_cxsf, r1			@ save in spsr_svc
+#if defined(CONFIG_CPU_32v6K)
+	clrex					@ clear the exclusive monitor
+#elif defined (CONFIG_CPU_V6)
+	strex	r1, r2, [sp]			@ clear the exclusive monitor
+#endif
 	.if	\fast
 	ldmdb	sp, {r1 - lr}^			@ get calling r1 - lr
 	.else
@@ -98,6 +110,7 @@
 	.endm
 #else	/* CONFIG_THUMB2_KERNEL */
 	.macro	svc_exit, rpsr
+	clrex					@ clear the exclusive monitor
 	ldr	r0, [sp, #S_SP]			@ top of the stack
 	ldr	r1, [sp, #S_PC]			@ return address
 	tst	r0, #4				@ orig stack 8-byte aligned?
@@ -110,6 +123,7 @@
 	.endm
 
 	.macro	restore_user_regs, fast = 0, offset = 0
+	clrex					@ clear the exclusive monitor
 	mov	r2, sp
 	load_user_sp_lr r2, r3, \offset + S_SP	@ calling sp, lr
 	ldr	r1, [sp, #\offset + S_PSR]	@ get calling cpsr

arch/arm/kernel/kprobes.c

@@ -22,6 +22,7 @@
 #include <linux/kernel.h>
 #include <linux/kprobes.h>
 #include <linux/module.h>
+#include <linux/stop_machine.h>
 #include <linux/stringify.h>
 #include <asm/traps.h>
 #include <asm/cacheflush.h>
@@ -83,10 +84,24 @@ void __kprobes arch_arm_kprobe(struct kprobe *p)
 	flush_insns(p->addr, 1);
 }
 
+/*
+ * The actual disarming is done here on each CPU and synchronized using
+ * stop_machine. This synchronization is necessary on SMP to avoid removing
+ * a probe between the moment the 'Undefined Instruction' exception is raised
+ * and the moment the exception handler reads the faulting instruction from
+ * memory.
+ */
+int __kprobes __arch_disarm_kprobe(void *p)
+{
+	struct kprobe *kp = p;
+	*kp->addr = kp->opcode;
+	flush_insns(kp->addr, 1);
+	return 0;
+}
+
 void __kprobes arch_disarm_kprobe(struct kprobe *p)
 {
-	*p->addr = p->opcode;
-	flush_insns(p->addr, 1);
+	stop_machine(__arch_disarm_kprobe, p, &cpu_online_map);
 }
 
 void __kprobes arch_remove_kprobe(struct kprobe *p)

arch/arm/kernel/setup.c

@@ -45,6 +45,7 @@
 
 #include "compat.h"
 #include "atags.h"
+#include "tcm.h"
 
 #ifndef MEM_SIZE
 #define MEM_SIZE	(16*1024*1024)
@@ -749,6 +750,7 @@ void __init setup_arch(char **cmdline_p)
 #endif
 
 	cpu_init();
+	tcm_init();
 
 	/*
 	 * Set up various architecture-specific pointers

arch/arm/kernel/tcm.c

@@ -0,0 +1,246 @@
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/stddef.h>
+#include <linux/ioport.h>
+#include <linux/genalloc.h>
+#include <linux/string.h> /* memcpy */
+#include <asm/page.h> /* PAGE_SHIFT */
+#include <asm/cputype.h>
+#include <asm/mach/map.h>
+#include <mach/memory.h>
+#include "tcm.h"
+
+/* Scream and warn about misuse */
+#if !defined(ITCM_OFFSET) || !defined(ITCM_END) || \
+    !defined(DTCM_OFFSET) || !defined(DTCM_END)
+#error "TCM support selected but offsets not defined!"
+#endif
+
+static struct gen_pool *tcm_pool;
+
+/* TCM section definitions from the linker */
+extern char __itcm_start, __sitcm_text, __eitcm_text;
+extern char __dtcm_start, __sdtcm_data, __edtcm_data;
+
+/*
+ * TCM memory resources
+ */
+static struct resource dtcm_res = {
+	.name = "DTCM RAM",
+	.start = DTCM_OFFSET,
+	.end = DTCM_END,
+	.flags = IORESOURCE_MEM
+};
+
+static struct resource itcm_res = {
+	.name = "ITCM RAM",
+	.start = ITCM_OFFSET,
+	.end = ITCM_END,
+	.flags = IORESOURCE_MEM
+};
+
+static struct map_desc dtcm_iomap[] __initdata = {
+	{
+		.virtual	= DTCM_OFFSET,
+		.pfn		= __phys_to_pfn(DTCM_OFFSET),
+		.length		= (DTCM_END - DTCM_OFFSET + 1),
+		.type		= MT_UNCACHED
+	}
+};
+
+static struct map_desc itcm_iomap[] __initdata = {
+	{
+		.virtual	= ITCM_OFFSET,
+		.pfn		= __phys_to_pfn(ITCM_OFFSET),
+		.length		= (ITCM_END - ITCM_OFFSET + 1),
+		.type		= MT_UNCACHED
+	}
+};
+
+/*
+ * Allocate a chunk of TCM memory
+ */
+void *tcm_alloc(size_t len)
+{
+	unsigned long vaddr;
+
+	if (!tcm_pool)
+		return NULL;
+
+	vaddr = gen_pool_alloc(tcm_pool, len);
+	if (!vaddr)
+		return NULL;
+
+	return (void *) vaddr;
+}
+EXPORT_SYMBOL(tcm_alloc);
+
+/*
+ * Free a chunk of TCM memory
+ */
+void tcm_free(void *addr, size_t len)
+{
+	gen_pool_free(tcm_pool, (unsigned long) addr, len);
+}
+EXPORT_SYMBOL(tcm_free);
+
+
+static void __init setup_tcm_bank(u8 type, u32 offset, u32 expected_size)
+{
+	const int tcm_sizes[16] = { 0, -1, -1, 4, 8, 16, 32, 64, 128,
+				    256, 512, 1024, -1, -1, -1, -1 };
+	u32 tcm_region;
+	int tcm_size;
+
+	/* Read the special TCM region register c9, 0 */
+	if (!type)
+		asm("mrc	p15, 0, %0, c9, c1, 0"
+		    : "=r" (tcm_region));
+	else
+		asm("mrc	p15, 0, %0, c9, c1, 1"
+		    : "=r" (tcm_region));
+
+	tcm_size = tcm_sizes[(tcm_region >> 2) & 0x0f];
+	if (tcm_size < 0) {
+		pr_err("CPU: %sTCM of unknown size!\n",
+			type ? "I" : "D");
+	} else {
+		pr_info("CPU: found %sTCM %dk @ %08x, %senabled\n",
+			type ? "I" : "D",
+			tcm_size,
+			(tcm_region & 0xfffff000U),
+			(tcm_region & 1) ? "" : "not ");
+	}
+
+	if (tcm_size != expected_size) {
+		pr_crit("CPU: %sTCM was detected %dk but expected %dk!\n",
+		       type ? "I" : "D",
+		       tcm_size,
+		       expected_size);
+		/* Adjust to the expected size? what can we do... */
+	}
+
+	/* Force move the TCM bank to where we want it, enable */
+	tcm_region = offset | (tcm_region & 0x00000ffeU) | 1;
+
+	if (!type)
+		asm("mcr	p15, 0, %0, c9, c1, 0"
+		    : /* No output operands */
+		    : "r" (tcm_region));
+	else
+		asm("mcr	p15, 0, %0, c9, c1, 1"
+		    : /* No output operands */
+		    : "r" (tcm_region));
+
+	pr_debug("CPU: moved %sTCM %dk to %08x, enabled\n",
+		 type ? "I" : "D",
+		 tcm_size,
+		 (tcm_region & 0xfffff000U));
+}
+
+/*
+ * This initializes the TCM memory
+ */
+void __init tcm_init(void)
+{
+	u32 tcm_status = read_cpuid_tcmstatus();
+	char *start;
+	char *end;
+	char *ram;
+
+	/* Setup DTCM if present */
+	if (tcm_status & (1 << 16)) {
+		setup_tcm_bank(0, DTCM_OFFSET,
+			       (DTCM_END - DTCM_OFFSET + 1) >> 10);
+		request_resource(&iomem_resource, &dtcm_res);
+		iotable_init(dtcm_iomap, 1);
+		/* Copy data from RAM to DTCM */
+		start = &__sdtcm_data;
+		end   = &__edtcm_data;
+		ram   = &__dtcm_start;
+		memcpy(start, ram, (end-start));
+		pr_debug("CPU DTCM: copied data from %p - %p\n", start, end);
+	}
+
+	/* Setup ITCM if present */
+	if (tcm_status & 1) {
+		setup_tcm_bank(1, ITCM_OFFSET,
+			       (ITCM_END - ITCM_OFFSET + 1) >> 10);
+		request_resource(&iomem_resource, &itcm_res);
+		iotable_init(itcm_iomap, 1);
+		/* Copy code from RAM to ITCM */
+		start = &__sitcm_text;
+		end   = &__eitcm_text;
+		ram   = &__itcm_start;
+		memcpy(start, ram, (end-start));
+		pr_debug("CPU ITCM: copied code from %p - %p\n", start, end);
+	}
+}
+
+/*
+ * This creates the TCM memory pool and has to be done later,
+ * during the core_initicalls, since the allocator is not yet
+ * up and running when the first initialization runs.
+ */
+static int __init setup_tcm_pool(void)
+{
+	u32 tcm_status = read_cpuid_tcmstatus();
+	u32 dtcm_pool_start = (u32) &__edtcm_data;
+	u32 itcm_pool_start = (u32) &__eitcm_text;
+	int ret;
+
+	/*
+	 * Set up malloc pool, 2^2 = 4 bytes granularity since
+	 * the TCM is sometimes just 4 KiB. NB: pages and cache
+	 * line alignments does not matter in TCM!
+	 */
+	tcm_pool = gen_pool_create(2, -1);
+
+	pr_debug("Setting up TCM memory pool\n");
+
+	/* Add the rest of DTCM to the TCM pool */
+	if (tcm_status & (1 << 16)) {
+		if (dtcm_pool_start < DTCM_END) {
+			ret = gen_pool_add(tcm_pool, dtcm_pool_start,
+					   DTCM_END - dtcm_pool_start + 1, -1);
+			if (ret) {
+				pr_err("CPU DTCM: could not add DTCM " \
+				       "remainder to pool!\n");
+				return ret;
+			}
+			pr_debug("CPU DTCM: Added %08x bytes @ %08x to " \
+				 "the TCM memory pool\n",
+				 DTCM_END - dtcm_pool_start + 1,
+				 dtcm_pool_start);
+		}
+	}
+
+	/* Add the rest of ITCM to the TCM pool */
+	if (tcm_status & 1) {
+		if (itcm_pool_start < ITCM_END) {
+			ret = gen_pool_add(tcm_pool, itcm_pool_start,
+					   ITCM_END - itcm_pool_start + 1, -1);
+			if (ret) {
+				pr_err("CPU ITCM: could not add ITCM " \
+				       "remainder to pool!\n");
+				return ret;
+			}
+			pr_debug("CPU ITCM: Added %08x bytes @ %08x to " \
+				 "the TCM memory pool\n",
+				 ITCM_END - itcm_pool_start + 1,
+				 itcm_pool_start);
+		}
+	}
+	return 0;
+}
+
+core_initcall(setup_tcm_pool);

arch/arm/kernel/tcm.h

@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+
+#ifdef CONFIG_HAVE_TCM
+void __init tcm_init(void);
+#else
+/* No TCM support, just blank inlines to be optimized out */
+inline void tcm_init(void)
+{
+}
+#endif

arch/arm/kernel/vmlinux.lds.S

@@ -199,6 +199,63 @@ SECTIONS
 	}
 	_edata_loc = __data_loc + SIZEOF(.data);
 
+#ifdef CONFIG_HAVE_TCM
+        /*
+	 * We align everything to a page boundary so we can
+	 * free it after init has commenced and TCM contents have
+	 * been copied to its destination.
+	 */
+	.tcm_start : {
+		. = ALIGN(PAGE_SIZE);
+		__tcm_start = .;
+		__itcm_start = .;
+	}
+
+	/*
+	 * Link these to the ITCM RAM
+	 * Put VMA to the TCM address and LMA to the common RAM
+	 * and we'll upload the contents from RAM to TCM and free
+	 * the used RAM after that.
+	 */
+	.text_itcm ITCM_OFFSET : AT(__itcm_start)
+	{
+		__sitcm_text = .;
+		*(.tcm.text)
+		*(.tcm.rodata)
+		. = ALIGN(4);
+		__eitcm_text = .;
+	}
+
+	/*
+	 * Reset the dot pointer, this is needed to create the
+	 * relative __dtcm_start below (to be used as extern in code).
+	 */
+	. = ADDR(.tcm_start) + SIZEOF(.tcm_start) + SIZEOF(.text_itcm);
+
+	.dtcm_start : {
+		__dtcm_start = .;
+	}
+
+	/* TODO: add remainder of ITCM as well, that can be used for data! */
+	.data_dtcm DTCM_OFFSET : AT(__dtcm_start)
+	{
+		. = ALIGN(4);
+		__sdtcm_data = .;
+		*(.tcm.data)
+		. = ALIGN(4);
+		__edtcm_data = .;
+	}
+
+	/* Reset the dot pointer or the linker gets confused */
+	. = ADDR(.dtcm_start) + SIZEOF(.data_dtcm);
+
+	/* End marker for freeing TCM copy in linked object */
+	.tcm_end : AT(ADDR(.dtcm_start) + SIZEOF(.data_dtcm)){
+		. = ALIGN(PAGE_SIZE);
+		__tcm_end = .;
+	}
+#endif
+
 	.bss : {
 		__bss_start = .;	/* BSS				*/
 		*(.bss)

arch/arm/lib/copy_page.S

@@ -12,8 +12,9 @@
 #include <linux/linkage.h>
 #include <asm/assembler.h>
 #include <asm/asm-offsets.h>
+#include <asm/cache.h>
 
-#define COPY_COUNT (PAGE_SZ/64 PLD( -1 ))
+#define COPY_COUNT (PAGE_SZ / (2 * L1_CACHE_BYTES) PLD( -1 ))
 
 		.text
 		.align	5
@@ -26,17 +27,16 @@
 ENTRY(copy_page)
 		stmfd	sp!, {r4, lr}			@	2
 	PLD(	pld	[r1, #0]		)
-	PLD(	pld	[r1, #32]		)
+	PLD(	pld	[r1, #L1_CACHE_BYTES]		)
 		mov	r2, #COPY_COUNT			@	1
 		ldmia	r1!, {r3, r4, ip, lr}		@	4+1
-1:	PLD(	pld	[r1, #64]		)
-	PLD(	pld	[r1, #96]		)
-2:		stmia	r0!, {r3, r4, ip, lr}		@	4
-		ldmia	r1!, {r3, r4, ip, lr}		@	4+1
-		stmia	r0!, {r3, r4, ip, lr}		@	4
-		ldmia	r1!, {r3, r4, ip, lr}		@	4+1
+1:	PLD(	pld	[r1, #2 * L1_CACHE_BYTES])
+	PLD(	pld	[r1, #3 * L1_CACHE_BYTES])
+2:
+	.rept	(2 * L1_CACHE_BYTES / 16 - 1)
 		stmia	r0!, {r3, r4, ip, lr}		@	4
 		ldmia	r1!, {r3, r4, ip, lr}		@	4
+	.endr
 		subs	r2, r2, #1			@	1
 		stmia	r0!, {r3, r4, ip, lr}		@	4
 		ldmgtia	r1!, {r3, r4, ip, lr}		@	4

arch/arm/mach-at91/at91cap9_devices.c

@@ -771,9 +771,9 @@ void __init at91_add_device_pwm(u32 mask) {}
  *  AC97
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_SND_AT91_AC97) || defined(CONFIG_SND_AT91_AC97_MODULE)
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
 static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct atmel_ac97_data ac97_data;
+static struct ac97c_platform_data ac97_data;
 
 static struct resource ac97_resources[] = {
 	[0] = {
@@ -789,7 +789,7 @@ static struct resource ac97_resources[] = {
 };
 
 static struct platform_device at91cap9_ac97_device = {
-	.name		= "ac97c",
+	.name		= "atmel_ac97c",
 	.id		= 1,
 	.dev		= {
 				.dma_mask		= &ac97_dmamask,
@@ -800,7 +800,7 @@ static struct platform_device at91cap9_ac97_device = {
 	.num_resources	= ARRAY_SIZE(ac97_resources),
 };
 
-void __init at91_add_device_ac97(struct atmel_ac97_data *data)
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 {
 	if (!data)
 		return;
@@ -818,7 +818,7 @@ void __init at91_add_device_ac97(struct atmel_ac97_data *data)
 	platform_device_register(&at91cap9_ac97_device);
 }
 #else
-void __init at91_add_device_ac97(struct atmel_ac97_data *data) {}
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
 #endif
 
 

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -24,10 +24,58 @@
 #include <mach/at91sam9g45.h>
 #include <mach/at91sam9g45_matrix.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
 
 #include "generic.h"
 
 
+/* --------------------------------------------------------------------
+ *  HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+	.nr_channels	= 8,
+};
+
+static struct resource hdmac_resources[] = {
+	[0] = {
+		.start	= AT91_BASE_SYS + AT91_DMA,
+		.end	= AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= AT91SAM9G45_ID_DMA,
+		.end	= AT91SAM9G45_ID_DMA,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at_hdmac_device = {
+	.name		= "at_hdmac",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &hdmac_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &atdma_pdata,
+	},
+	.resource	= hdmac_resources,
+	.num_resources	= ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+	dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+	dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask);
+	platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
+
 /* --------------------------------------------------------------------
  *  USB Host (OHCI)
  * -------------------------------------------------------------------- */
@@ -549,6 +597,61 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 #endif
 
 
+/* --------------------------------------------------------------------
+ *  AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_AC97C,
+		.end	= AT91SAM9G45_BASE_AC97C + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_ID_AC97C,
+		.end	= AT91SAM9G45_ID_AC97C,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9g45_ac97_device = {
+	.name		= "atmel_ac97c",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &ac97_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &ac97_data,
+	},
+	.resource	= ac97_resources,
+	.num_resources	= ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+	if (!data)
+		return;
+
+	at91_set_A_periph(AT91_PIN_PD8, 0);	/* AC97FS */
+	at91_set_A_periph(AT91_PIN_PD9, 0);	/* AC97CK */
+	at91_set_A_periph(AT91_PIN_PD7, 0);	/* AC97TX */
+	at91_set_A_periph(AT91_PIN_PD6, 0);	/* AC97RX */
+
+	/* reset */
+	if (data->reset_pin)
+		at91_set_gpio_output(data->reset_pin, 0);
+
+	ac97_data = *data;
+	platform_device_register(&at91sam9g45_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
 /* --------------------------------------------------------------------
  *  LCD Controller
  * -------------------------------------------------------------------- */
@@ -1220,6 +1323,7 @@ void __init at91_add_device_serial(void) {}
  */
 static int __init at91_add_standard_devices(void)
 {
+	at91_add_device_hdmac();
 	at91_add_device_rtc();
 	at91_add_device_rtt();
 	at91_add_device_watchdog();

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -21,10 +21,56 @@
 #include <mach/at91sam9rl.h>
 #include <mach/at91sam9rl_matrix.h>
 #include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
 
 #include "generic.h"
 
 
+/* --------------------------------------------------------------------
+ *  HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+	.nr_channels	= 2,
+};
+
+static struct resource hdmac_resources[] = {
+	[0] = {
+		.start	= AT91_BASE_SYS + AT91_DMA,
+		.end	= AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= AT91SAM9RL_ID_DMA,
+		.end	= AT91SAM9RL_ID_DMA,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at_hdmac_device = {
+	.name		= "at_hdmac",
+	.id		= -1,
+	.dev		= {
+				.dma_mask		= &hdmac_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &atdma_pdata,
+	},
+	.resource	= hdmac_resources,
+	.num_resources	= ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+	dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+	platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
 /* --------------------------------------------------------------------
  *  USB HS Device (Gadget)
  * -------------------------------------------------------------------- */
@@ -397,6 +443,61 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 #endif
 
 
+/* --------------------------------------------------------------------
+ *  AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+	[0] = {
+		.start	= AT91SAM9RL_BASE_AC97C,
+		.end	= AT91SAM9RL_BASE_AC97C + SZ_16K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9RL_ID_AC97C,
+		.end	= AT91SAM9RL_ID_AC97C,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device at91sam9rl_ac97_device = {
+	.name		= "atmel_ac97c",
+	.id		= 0,
+	.dev		= {
+				.dma_mask		= &ac97_dmamask,
+				.coherent_dma_mask	= DMA_BIT_MASK(32),
+				.platform_data		= &ac97_data,
+	},
+	.resource	= ac97_resources,
+	.num_resources	= ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+	if (!data)
+		return;
+
+	at91_set_A_periph(AT91_PIN_PD1, 0);	/* AC97FS */
+	at91_set_A_periph(AT91_PIN_PD2, 0);	/* AC97CK */
+	at91_set_A_periph(AT91_PIN_PD3, 0);	/* AC97TX */
+	at91_set_A_periph(AT91_PIN_PD4, 0);	/* AC97RX */
+
+	/* reset */
+	if (data->reset_pin)
+		at91_set_gpio_output(data->reset_pin, 0);
+
+	ac97_data = *data;
+	platform_device_register(&at91sam9rl_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
 /* --------------------------------------------------------------------
  *  LCD Controller
  * -------------------------------------------------------------------- */
@@ -1103,6 +1204,7 @@ void __init at91_add_device_serial(void) {}
  */
 static int __init at91_add_standard_devices(void)
 {
+	at91_add_device_hdmac();
 	at91_add_device_rtc();
 	at91_add_device_rtt();
 	at91_add_device_watchdog();

arch/arm/mach-at91/board-cap9adk.c

@@ -364,7 +364,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
 /*
  * AC97
  */
-static struct atmel_ac97_data cap9adk_ac97_data = {
+static struct ac97c_platform_data cap9adk_ac97_data = {
 //	.reset_pin	= ... not connected
 };
 

arch/arm/mach-at91/board-neocore926.c

@@ -340,7 +340,7 @@ static void __init neocore926_add_device_buttons(void) {}
 /*
  * AC97
  */
-static struct atmel_ac97_data neocore926_ac97_data = {
+static struct ac97c_platform_data neocore926_ac97_data = {
 	.reset_pin	= AT91_PIN_PA13,
 };
 

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -310,6 +310,14 @@ static void __init ek_add_device_buttons(void) {}
 #endif
 
 
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
 /*
  * LEDs ... these could all be PWM-driven, for variable brightness
  */
@@ -372,6 +380,8 @@ static void __init ek_board_init(void)
 	at91_add_device_lcdc(&ek_lcdc_data);
 	/* Push Buttons */
 	ek_add_device_buttons();
+	/* AC97 */
+	at91_add_device_ac97(&ek_ac97_data);
 	/* LEDs */
 	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 	at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));

arch/arm/mach-at91/board-sam9rlek.c

@@ -210,6 +210,14 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
 #endif
 
 
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
 /*
  * LEDs
  */
@@ -299,6 +307,8 @@ static void __init ek_board_init(void)
 	at91_add_device_mmc(0, &ek_mmc_data);
 	/* LCD Controller */
 	at91_add_device_lcdc(&ek_lcdc_data);
+	/* AC97 */
+	at91_add_device_ac97(&ek_ac97_data);
 	/* Touch Screen Controller */
 	at91_add_device_tsadcc();
 	/* LEDs */

arch/arm/mach-integrator/integrator_cp.c

@@ -19,6 +19,7 @@
 #include <linux/amba/bus.h>
 #include <linux/amba/kmi.h>
 #include <linux/amba/clcd.h>
+#include <linux/amba/mmci.h>
 #include <linux/io.h>
 
 #include <asm/clkdev.h>
@@ -35,7 +36,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/irq.h>
-#include <asm/mach/mmc.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 
@@ -400,7 +400,7 @@ static unsigned int mmc_status(struct device *dev)
 	return status & 8;
 }
 
-static struct mmc_platform_data mmc_data = {
+static struct mmci_platform_data mmc_data = {
 	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
 	.status		= mmc_status,
 	.gpio_wp	= -1,

arch/arm/mach-pxa/Kconfig

@@ -21,6 +21,11 @@ config CPU_PXA930
 
 config CPU_PXA935
 	bool "PXA935 (codename Tavor-P65)"
+	select CPU_PXA930
+
+config CPU_PXA950
+	bool "PXA950 (codename Tavor-PV2)"
+	select CPU_PXA930
 
 endmenu
 
@@ -79,6 +84,12 @@ config MACH_MP900C
 	bool "Nec Mobilepro 900/c"
 	select PXA25x
 
+config MACH_BALLOON3
+	bool "Balloon 3 board"
+	select PXA27x
+	select IWMMXT
+	select PXA_HAVE_BOARD_IRQS
+
 config ARCH_PXA_IDP
 	bool "Accelent Xscale IDP"
 	select PXA25x
@@ -371,6 +382,15 @@ config MACH_PALMTE2
 	  Say Y here if you intend to run this kernel on a Palm Tungsten|E2
 	  handheld computer.
 
+config MACH_PALMTC
+	bool "Palm Tungsten|C"
+	default y
+	depends on ARCH_PXA_PALM
+	select PXA25x
+	help
+	  Say Y here if you intend to run this kernel on a Palm Tungsten|C
+	  handheld computer.
+
 config MACH_PALMT5
 	bool "Palm Tungsten|T5"
 	default y
@@ -458,6 +478,7 @@ config PXA_EZX
 	select PXA27x
 	select IWMMXT
 	select HAVE_PWM
+	select PXA_HAVE_BOARD_IRQS
 
 config MACH_EZX_A780
 	bool "Motorola EZX A780"
@@ -489,6 +510,21 @@ config MACH_EZX_E2
 	default y
 	depends on PXA_EZX
 
+config MACH_XCEP
+	bool "Iskratel Electronics XCEP"
+	select PXA25x
+	select MTD
+	select MTD_PARTITIONS
+	select MTD_PHYSMAP
+	select MTD_CFI_INTELEXT
+	select MTD_CFI
+	select MTD_CHAR
+	select SMC91X
+	select PXA_SSP
+	help
+	  PXA255 based Single Board Computer with SMC 91C111 ethernet chip and 64 MB of flash.
+	  Tuned for usage in Libera instruments for particle accelerators.
+
 endmenu
 
 config PXA25x

arch/arm/mach-pxa/Makefile

@@ -31,6 +31,7 @@ obj-$(CONFIG_GUMSTIX_AM300EPD)	+= am300epd.o
 obj-$(CONFIG_ARCH_LUBBOCK)	+= lubbock.o
 obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o
 obj-$(CONFIG_MACH_MAINSTONE)	+= mainstone.o
+obj-$(CONFIG_MACH_BALLOON3)	+= balloon3.o
 obj-$(CONFIG_MACH_MP900C)	+= mp900.o
 obj-$(CONFIG_ARCH_PXA_IDP)	+= idp.o
 obj-$(CONFIG_MACH_TRIZEPS4)	+= trizeps4.o
@@ -58,6 +59,7 @@ obj-$(CONFIG_MACH_E750)		+= e750.o
 obj-$(CONFIG_MACH_E400)		+= e400.o
 obj-$(CONFIG_MACH_E800)		+= e800.o
 obj-$(CONFIG_MACH_PALMTE2)	+= palmte2.o
+obj-$(CONFIG_MACH_PALMTC)	+= palmtc.o
 obj-$(CONFIG_MACH_PALMT5)	+= palmt5.o
 obj-$(CONFIG_MACH_PALMTX)	+= palmtx.o
 obj-$(CONFIG_MACH_PALMLD)	+= palmld.o
@@ -78,6 +80,8 @@ obj-$(CONFIG_MACH_ARMCORE)      += cm-x2xx.o cm-x255.o cm-x270.o
 obj-$(CONFIG_MACH_CM_X300)      += cm-x300.o
 obj-$(CONFIG_PXA_EZX)           += ezx.o
 
+obj-$(CONFIG_MACH_XCEP)         += xcep.o
+
 obj-$(CONFIG_MACH_INTELMOTE2)   += imote2.o
 obj-$(CONFIG_MACH_STARGATE2)	+= stargate2.o
 obj-$(CONFIG_MACH_CSB726)	+= csb726.o

arch/arm/mach-pxa/balloon3.c

@@ -0,0 +1,361 @@
+/*
+ *  linux/arch/arm/mach-pxa/balloon3.c
+ *
+ *  Support for Balloonboard.org Balloon3 board.
+ *
+ *  Author:	Nick Bane, Wookey, Jonathan McDowell
+ *  Created:	June, 2006
+ *  Copyright:	Toby Churchill Ltd
+ *  Derived from mainstone.c, by Nico Pitre
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/bitops.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/ioport.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/types.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/flash.h>
+
+#include <mach/pxa27x.h>
+#include <mach/balloon3.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
+
+#include <plat/i2c.h>
+
+#include "generic.h"
+#include "devices.h"
+
+static unsigned long balloon3_irq_enabled;
+
+static unsigned long balloon3_features_present =
+		(1 << BALLOON3_FEATURE_OHCI) | (1 << BALLOON3_FEATURE_CF) |
+		(1 << BALLOON3_FEATURE_AUDIO) |
+		(1 << BALLOON3_FEATURE_TOPPOLY);
+
+int balloon3_has(enum balloon3_features feature)
+{
+	return (balloon3_features_present & (1 << feature)) ? 1 : 0;
+}
+EXPORT_SYMBOL_GPL(balloon3_has);
+
+int __init parse_balloon3_features(char *arg)
+{
+	if (!arg)
+		return 0;
+
+	return strict_strtoul(arg, 0, &balloon3_features_present);
+}
+early_param("balloon3_features", parse_balloon3_features);
+
+static void balloon3_mask_irq(unsigned int irq)
+{
+	int balloon3_irq = (irq - BALLOON3_IRQ(0));
+	balloon3_irq_enabled &= ~(1 << balloon3_irq);
+	__raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static void balloon3_unmask_irq(unsigned int irq)
+{
+	int balloon3_irq = (irq - BALLOON3_IRQ(0));
+	balloon3_irq_enabled |= (1 << balloon3_irq);
+	__raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static struct irq_chip balloon3_irq_chip = {
+	.name		= "FPGA",
+	.ack		= balloon3_mask_irq,
+	.mask		= balloon3_mask_irq,
+	.unmask		= balloon3_unmask_irq,
+};
+
+static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+					balloon3_irq_enabled;
+
+	do {
+		/* clear useless edge notification */
+		if (desc->chip->ack)
+			desc->chip->ack(BALLOON3_AUX_NIRQ);
+		while (pending) {
+			irq = BALLOON3_IRQ(0) + __ffs(pending);
+			generic_handle_irq(irq);
+			pending &= pending - 1;
+		}
+		pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+				balloon3_irq_enabled;
+	} while (pending);
+}
+
+static void __init balloon3_init_irq(void)
+{
+	int irq;
+
+	pxa27x_init_irq();
+	/* setup extra Balloon3 irqs */
+	for (irq = BALLOON3_IRQ(0); irq <= BALLOON3_IRQ(7); irq++) {
+		set_irq_chip(irq, &balloon3_irq_chip);
+		set_irq_handler(irq, handle_level_irq);
+		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+	}
+
+	set_irq_chained_handler(BALLOON3_AUX_NIRQ, balloon3_irq_handler);
+	set_irq_type(BALLOON3_AUX_NIRQ, IRQ_TYPE_EDGE_FALLING);
+
+	pr_debug("%s: chained handler installed - irq %d automatically "
+		"enabled\n", __func__, BALLOON3_AUX_NIRQ);
+}
+
+static void balloon3_backlight_power(int on)
+{
+	pr_debug("%s: power is %s\n", __func__, on ? "on" : "off");
+	gpio_set_value(BALLOON3_GPIO_RUN_BACKLIGHT, on);
+}
+
+static unsigned long balloon3_lcd_pin_config[] = {
+	/* LCD - 16bpp Active TFT */
+	GPIO58_LCD_LDD_0,
+	GPIO59_LCD_LDD_1,
+	GPIO60_LCD_LDD_2,
+	GPIO61_LCD_LDD_3,
+	GPIO62_LCD_LDD_4,
+	GPIO63_LCD_LDD_5,
+	GPIO64_LCD_LDD_6,
+	GPIO65_LCD_LDD_7,
+	GPIO66_LCD_LDD_8,
+	GPIO67_LCD_LDD_9,
+	GPIO68_LCD_LDD_10,
+	GPIO69_LCD_LDD_11,
+	GPIO70_LCD_LDD_12,
+	GPIO71_LCD_LDD_13,
+	GPIO72_LCD_LDD_14,
+	GPIO73_LCD_LDD_15,
+	GPIO74_LCD_FCLK,
+	GPIO75_LCD_LCLK,
+	GPIO76_LCD_PCLK,
+	GPIO77_LCD_BIAS,
+
+	GPIO99_GPIO,		/* Backlight */
+};
+
+static struct pxafb_mode_info balloon3_lcd_modes[] = {
+	{
+		.pixclock		= 38000,
+		.xres			= 480,
+		.yres			= 640,
+		.bpp			= 16,
+		.hsync_len		= 8,
+		.left_margin		= 8,
+		.right_margin		= 8,
+		.vsync_len		= 2,
+		.upper_margin		= 4,
+		.lower_margin		= 5,
+		.sync			= 0,
+	},
+};
+
+static struct pxafb_mach_info balloon3_pxafb_info = {
+	.modes			= balloon3_lcd_modes,
+	.num_modes		= ARRAY_SIZE(balloon3_lcd_modes),
+	.lcd_conn		= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+	.pxafb_backlight_power	= balloon3_backlight_power,
+};
+
+static unsigned long balloon3_mmc_pin_config[] = {
+	GPIO32_MMC_CLK,
+	GPIO92_MMC_DAT_0,
+	GPIO109_MMC_DAT_1,
+	GPIO110_MMC_DAT_2,
+	GPIO111_MMC_DAT_3,
+	GPIO112_MMC_CMD,
+};
+
+static void balloon3_mci_setpower(struct device *dev, unsigned int vdd)
+{
+	struct pxamci_platform_data *p_d = dev->platform_data;
+
+	if ((1 << vdd) & p_d->ocr_mask) {
+		pr_debug("%s: on\n", __func__);
+		/* FIXME something to prod here? */
+	} else {
+		pr_debug("%s: off\n", __func__);
+		/* FIXME something to prod here? */
+	}
+}
+
+static struct pxamci_platform_data balloon3_mci_platform_data = {
+	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
+	.setpower 	= balloon3_mci_setpower,
+};
+
+static int balloon3_udc_is_connected(void)
+{
+	pr_debug("%s: udc connected\n", __func__);
+	return 1;
+}
+
+static void balloon3_udc_command(int cmd)
+{
+	switch (cmd) {
+	case PXA2XX_UDC_CMD_CONNECT:
+		UP2OCR |= (UP2OCR_DPPUE + UP2OCR_DPPUBE);
+		pr_debug("%s: connect\n", __func__);
+		break;
+	case PXA2XX_UDC_CMD_DISCONNECT:
+		UP2OCR &= ~UP2OCR_DPPUE;
+		pr_debug("%s: disconnect\n", __func__);
+		break;
+	}
+}
+
+static struct pxa2xx_udc_mach_info balloon3_udc_info = {
+	.udc_is_connected = balloon3_udc_is_connected,
+	.udc_command      = balloon3_udc_command,
+};
+
+static struct pxaficp_platform_data balloon3_ficp_platform_data = {
+	.transceiver_cap  = IR_SIRMODE | IR_FIRMODE | IR_OFF,
+};
+
+static unsigned long balloon3_ohci_pin_config[] = {
+	GPIO88_USBH1_PWR,
+	GPIO89_USBH1_PEN,
+};
+
+static struct pxaohci_platform_data balloon3_ohci_platform_data = {
+	.port_mode	= PMM_PERPORT_MODE,
+	.flags		= ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW,
+};
+
+static unsigned long balloon3_pin_config[] __initdata = {
+	/* Select BTUART 'COM1/ttyS0' as IO option for pins 42/43/44/45 */
+	GPIO42_BTUART_RXD,
+	GPIO43_BTUART_TXD,
+	GPIO44_BTUART_CTS,
+	GPIO45_BTUART_RTS,
+
+	/* Wakeup GPIO */
+	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
+
+	/* NAND & IDLE LED GPIOs */
+	GPIO9_GPIO,
+	GPIO10_GPIO,
+};
+
+static struct gpio_led balloon3_gpio_leds[] = {
+	{
+		.name			= "balloon3:green:idle",
+		.default_trigger	= "heartbeat",
+		.gpio			= BALLOON3_GPIO_LED_IDLE,
+		.active_low		= 1,
+	},
+	{
+		.name			= "balloon3:green:nand",
+		.default_trigger	= "nand-disk",
+		.gpio			= BALLOON3_GPIO_LED_NAND,
+		.active_low		= 1,
+	},
+};
+
+static struct gpio_led_platform_data balloon3_gpio_leds_platform_data = {
+	.leds		= balloon3_gpio_leds,
+	.num_leds	= ARRAY_SIZE(balloon3_gpio_leds),
+};
+
+static struct platform_device balloon3led_device = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &balloon3_gpio_leds_platform_data,
+	},
+};
+
+static void __init balloon3_init(void)
+{
+	pr_info("Initialising Balloon3\n");
+
+	/* system bus arbiter setting
+	 * - Core_Park
+	 * - LCD_wt:DMA_wt:CORE_Wt = 2:3:4
+	 */
+	ARB_CNTRL = ARB_CORE_PARK | 0x234;
+
+	pxa_set_i2c_info(NULL);
+	if (balloon3_has(BALLOON3_FEATURE_AUDIO))
+		pxa_set_ac97_info(NULL);
+
+	if (balloon3_has(BALLOON3_FEATURE_TOPPOLY)) {
+		pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_lcd_pin_config));
+		gpio_request(BALLOON3_GPIO_RUN_BACKLIGHT,
+			"LCD Backlight Power");
+		gpio_direction_output(BALLOON3_GPIO_RUN_BACKLIGHT, 1);
+		set_pxa_fb_info(&balloon3_pxafb_info);
+	}
+
+	if (balloon3_has(BALLOON3_FEATURE_MMC)) {
+		pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_mmc_pin_config));
+		pxa_set_mci_info(&balloon3_mci_platform_data);
+	}
+	pxa_set_ficp_info(&balloon3_ficp_platform_data);
+	if (balloon3_has(BALLOON3_FEATURE_OHCI)) {
+		pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_ohci_pin_config));
+		pxa_set_ohci_info(&balloon3_ohci_platform_data);
+	}
+	pxa_set_udc_info(&balloon3_udc_info);
+
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_pin_config));
+
+	platform_device_register(&balloon3led_device);
+}
+
+static struct map_desc balloon3_io_desc[] __initdata = {
+	{	/* CPLD/FPGA */
+		.virtual	=  BALLOON3_FPGA_VIRT,
+		.pfn		= __phys_to_pfn(BALLOON3_FPGA_PHYS),
+		.length		= BALLOON3_FPGA_LENGTH,
+		.type		= MT_DEVICE,
+	},
+};
+
+static void __init balloon3_map_io(void)
+{
+	pxa_map_io();
+	iotable_init(balloon3_io_desc, ARRAY_SIZE(balloon3_io_desc));
+}
+
+MACHINE_START(BALLOON3, "Balloon3")
+	/* Maintainer: Nick Bane. */
+	.phys_io	= 0x40000000,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.map_io		= balloon3_map_io,
+	.init_irq	= balloon3_init_irq,
+	.timer		= &pxa_timer,
+	.init_machine	= balloon3_init,
+	.boot_params	= PHYS_OFFSET + 0x100,
+MACHINE_END

arch/arm/mach-pxa/clock.h

@@ -12,7 +12,6 @@ struct clk {
 	unsigned int		cken;
 	unsigned int		delay;
 	unsigned int		enabled;
-	struct clk		*other;
 };
 
 #define INIT_CLKREG(_clk,_devname,_conname)		\

arch/arm/mach-pxa/cm-x270.c

@@ -13,13 +13,18 @@
 #include <linux/sysdev.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
+#include <linux/delay.h>
 
 #include <linux/rtc-v3020.h>
 #include <video/mbxfb.h>
 
+#include <linux/spi/spi.h>
+#include <linux/spi/libertas_spi.h>
+
 #include <mach/pxa27x.h>
 #include <mach/ohci.h>
 #include <mach/mmc.h>
+#include <mach/pxa2xx_spi.h>
 
 #include "generic.h"
 
@@ -34,6 +39,10 @@
 /* MMC power enable */
 #define GPIO105_MMC_POWER	(105)
 
+/* WLAN GPIOS */
+#define GPIO19_WLAN_STRAP	(19)
+#define GPIO102_WLAN_RST	(102)
+
 static unsigned long cmx270_pin_config[] = {
 	/* AC'97 */
 	GPIO28_AC97_BITCLK,
@@ -94,8 +103,8 @@ static unsigned long cmx270_pin_config[] = {
 	GPIO26_SSP1_RXD,
 
 	/* SSP2 */
-	GPIO19_SSP2_SCLK,
-	GPIO14_SSP2_SFRM,
+	GPIO19_GPIO,	/* SSP2 clock is used as GPIO for Libertas pin-strap */
+	GPIO14_GPIO,
 	GPIO87_SSP2_TXD,
 	GPIO88_SSP2_RXD,
 
@@ -123,6 +132,7 @@ static unsigned long cmx270_pin_config[] = {
 	GPIO0_GPIO	| WAKEUP_ON_EDGE_BOTH,
 	GPIO105_GPIO	| MFP_LPM_DRIVE_HIGH,	/* MMC/SD power */
 	GPIO53_GPIO,				/* PC card reset */
+	GPIO102_GPIO,				/* WLAN reset */
 
 	/* NAND controls */
 	GPIO11_GPIO	| MFP_LPM_DRIVE_HIGH,	/* NAND CE# */
@@ -131,6 +141,7 @@ static unsigned long cmx270_pin_config[] = {
 	/* interrupts */
 	GPIO10_GPIO,	/* DM9000 interrupt */
 	GPIO83_GPIO,	/* MMC card detect */
+	GPIO95_GPIO,	/* WLAN interrupt */
 };
 
 /* V3020 RTC */
@@ -271,64 +282,114 @@ static inline void cmx270_init_ohci(void) {}
 #endif
 
 #if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
-static int cmx270_mci_init(struct device *dev,
-			   irq_handler_t cmx270_detect_int,
-			   void *data)
+static struct pxamci_platform_data cmx270_mci_platform_data = {
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO83_MMC_IRQ,
+	.gpio_card_ro		= -1,
+	.gpio_power		= GPIO105_MMC_POWER,
+	.gpio_power_invert	= 1,
+};
+
+static void __init cmx270_init_mmc(void)
 {
-	int err;
+	pxa_set_mci_info(&cmx270_mci_platform_data);
+}
+#else
+static inline void cmx270_init_mmc(void) {}
+#endif
+
+#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
+static struct pxa2xx_spi_master cm_x270_spi_info = {
+	.num_chipselect	= 1,
+	.enable_dma	= 1,
+};
+
+static struct pxa2xx_spi_chip cm_x270_libertas_chip = {
+	.rx_threshold	= 1,
+	.tx_threshold	= 1,
+	.timeout	= 1000,
+	.gpio_cs	= 14,
+};
+
+static unsigned long cm_x270_libertas_pin_config[] = {
+	/* SSP2 */
+	GPIO19_SSP2_SCLK,
+	GPIO14_GPIO,
+	GPIO87_SSP2_TXD,
+	GPIO88_SSP2_RXD,
+
+};
 
-	err = gpio_request(GPIO105_MMC_POWER, "MMC/SD power");
-	if (err) {
-		dev_warn(dev, "power gpio unavailable\n");
+static int cm_x270_libertas_setup(struct spi_device *spi)
+{
+	int err = gpio_request(GPIO19_WLAN_STRAP, "WLAN STRAP");
+	if (err)
 		return err;
-	}
 
-	gpio_direction_output(GPIO105_MMC_POWER, 0);
+	err = gpio_request(GPIO102_WLAN_RST, "WLAN RST");
+	if (err)
+		goto err_free_strap;
 
-	err = request_irq(CMX270_MMC_IRQ, cmx270_detect_int,
-			  IRQF_DISABLED | IRQF_TRIGGER_FALLING,
-			  "MMC card detect", data);
-	if (err) {
-		gpio_free(GPIO105_MMC_POWER);
-		dev_err(dev, "cmx270_mci_init: MMC/SD: can't"
-			" request MMC card detect IRQ\n");
-	}
+	err = gpio_direction_output(GPIO102_WLAN_RST, 0);
+	if (err)
+		goto err_free_strap;
+	msleep(100);
+
+	err = gpio_direction_output(GPIO19_WLAN_STRAP, 1);
+	if (err)
+		goto err_free_strap;
+	msleep(100);
+
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(cm_x270_libertas_pin_config));
+
+	gpio_set_value(GPIO102_WLAN_RST, 1);
+	msleep(100);
+
+	spi->bits_per_word = 16;
+	spi_setup(spi);
+
+	return 0;
+
+err_free_strap:
+	gpio_free(GPIO19_WLAN_STRAP);
 
 	return err;
 }
 
-static void cmx270_mci_setpower(struct device *dev, unsigned int vdd)
+static int cm_x270_libertas_teardown(struct spi_device *spi)
 {
-	struct pxamci_platform_data *p_d = dev->platform_data;
-
-	if ((1 << vdd) & p_d->ocr_mask) {
-		dev_dbg(dev, "power on\n");
-		gpio_set_value(GPIO105_MMC_POWER, 0);
-	} else {
-		gpio_set_value(GPIO105_MMC_POWER, 1);
-		dev_dbg(dev, "power off\n");
-	}
-}
+	gpio_set_value(GPIO102_WLAN_RST, 0);
+	gpio_free(GPIO102_WLAN_RST);
+	gpio_free(GPIO19_WLAN_STRAP);
 
-static void cmx270_mci_exit(struct device *dev, void *data)
-{
-	free_irq(CMX270_MMC_IRQ, data);
-	gpio_free(GPIO105_MMC_POWER);
+	return 0;
 }
 
-static struct pxamci_platform_data cmx270_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init 		= cmx270_mci_init,
-	.setpower 	= cmx270_mci_setpower,
-	.exit		= cmx270_mci_exit,
+struct libertas_spi_platform_data cm_x270_libertas_pdata = {
+	.use_dummy_writes	= 1,
+	.setup			= cm_x270_libertas_setup,
+	.teardown		= cm_x270_libertas_teardown,
 };
 
-static void __init cmx270_init_mmc(void)
+static struct spi_board_info cm_x270_spi_devices[] __initdata = {
+	{
+		.modalias		= "libertas_spi",
+		.max_speed_hz		= 13000000,
+		.bus_num		= 2,
+		.irq			= gpio_to_irq(95),
+		.chip_select		= 0,
+		.controller_data	= &cm_x270_libertas_chip,
+		.platform_data		= &cm_x270_libertas_pdata,
+	},
+};
+
+static void __init cmx270_init_spi(void)
 {
-	pxa_set_mci_info(&cmx270_mci_platform_data);
+	pxa2xx_set_spi_info(2, &cm_x270_spi_info);
+	spi_register_board_info(ARRAY_AND_SIZE(cm_x270_spi_devices));
 }
 #else
-static inline void cmx270_init_mmc(void) {}
+static inline void cmx270_init_spi(void) {}
 #endif
 
 void __init cmx270_init(void)
@@ -343,4 +404,5 @@ void __init cmx270_init(void)
 	cmx270_init_mmc();
 	cmx270_init_ohci();
 	cmx270_init_2700G();
+	cmx270_init_spi();
 }

arch/arm/mach-pxa/cm-x300.c

@@ -306,68 +306,21 @@ static void cm_x300_mci_exit(struct device *dev, void *data)
 }
 
 static struct pxamci_platform_data cm_x300_mci_platform_data = {
-	.detect_delay	= 20,
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init 		= cm_x300_mci_init,
-	.exit		= cm_x300_mci_exit,
+	.detect_delay		= 20,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.init 			= cm_x300_mci_init,
+	.exit			= cm_x300_mci_exit,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
-static int cm_x300_mci2_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO85_MMC2_WP);
-}
-
-static int cm_x300_mci2_init(struct device *dev,
-			     irq_handler_t cm_x300_detect_int,
-			     void *data)
-{
-	int err;
-
-	/*
-	 * setup GPIO for CM-X300 MMC controller
-	 */
-	err = gpio_request(GPIO82_MMC2_IRQ, "mmc card detect");
-	if (err)
-		goto err_request_cd;
-	gpio_direction_input(GPIO82_MMC2_IRQ);
-
-	err = gpio_request(GPIO85_MMC2_WP, "mmc write protect");
-	if (err)
-		goto err_request_wp;
-	gpio_direction_input(GPIO85_MMC2_WP);
-
-	err = request_irq(CM_X300_MMC2_IRQ, cm_x300_detect_int,
-			  IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-			  "MMC card detect", data);
-	if (err) {
-		printk(KERN_ERR "%s: MMC/SD/SDIO: "
-				"can't request card detect IRQ\n", __func__);
-		goto err_request_irq;
-	}
-
-	return 0;
-
-err_request_irq:
-	gpio_free(GPIO85_MMC2_WP);
-err_request_wp:
-	gpio_free(GPIO82_MMC2_IRQ);
-err_request_cd:
-	return err;
-}
-
-static void cm_x300_mci2_exit(struct device *dev, void *data)
-{
-	free_irq(CM_X300_MMC2_IRQ, data);
-	gpio_free(GPIO82_MMC2_IRQ);
-	gpio_free(GPIO85_MMC2_WP);
-}
-
 static struct pxamci_platform_data cm_x300_mci2_platform_data = {
-	.detect_delay	= 20,
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init 		= cm_x300_mci2_init,
-	.exit		= cm_x300_mci2_exit,
-	.get_ro		= cm_x300_mci2_ro,
+	.detect_delay		= 20,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO82_MMC2_IRQ,
+	.gpio_card_ro		= GPIO85_MMC2_WP,
+	.gpio_power		= -1,
 };
 
 static void __init cm_x300_init_mmc(void)

arch/arm/mach-pxa/colibri-pxa300.c

@@ -172,6 +172,7 @@ void __init colibri_pxa300_init(void)
 {
 	colibri_pxa300_init_eth();
 	colibri_pxa300_init_ohci();
+	colibri_pxa3xx_init_nand();
 	colibri_pxa300_init_lcd();
 	colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO39_GPIO));
 	colibri_pxa310_init_ac97();

arch/arm/mach-pxa/colibri-pxa320.c

@@ -164,15 +164,48 @@ static inline void __init colibri_pxa320_init_ac97(void)
 static inline void colibri_pxa320_init_ac97(void) {}
 #endif
 
+/*
+ * The following configuration is verified to work with the Toradex Orchid
+ * carrier board
+ */
+static mfp_cfg_t colibri_pxa320_uart_pin_config[] __initdata = {
+	/* UART 1 configuration (may be set by bootloader) */
+	GPIO99_UART1_CTS,
+	GPIO104_UART1_RTS,
+	GPIO97_UART1_RXD,
+	GPIO98_UART1_TXD,
+	GPIO101_UART1_DTR,
+	GPIO103_UART1_DSR,
+	GPIO100_UART1_DCD,
+	GPIO102_UART1_RI,
+
+	/* UART 2 configuration */
+	GPIO109_UART2_CTS,
+	GPIO112_UART2_RTS,
+	GPIO110_UART2_RXD,
+	GPIO111_UART2_TXD,
+
+	/* UART 3 configuration */
+	GPIO30_UART3_RXD,
+	GPIO31_UART3_TXD,
+};
+
+static void __init colibri_pxa320_init_uart(void)
+{
+	pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_uart_pin_config));
+}
+
 void __init colibri_pxa320_init(void)
 {
 	colibri_pxa320_init_eth();
 	colibri_pxa320_init_ohci();
+	colibri_pxa3xx_init_nand();
 	colibri_pxa320_init_lcd();
 	colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO49_GPIO));
 	colibri_pxa320_init_ac97();
 	colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa320_mmc_pin_config),
 				mfp_to_gpio(MFP_PIN_GPIO28));
+	colibri_pxa320_init_uart();
 }
 
 MACHINE_START(COLIBRI320, "Toradex Colibri PXA320")

arch/arm/mach-pxa/colibri-pxa3xx.c

@@ -25,6 +25,7 @@
 #include <mach/colibri.h>
 #include <mach/mmc.h>
 #include <mach/pxafb.h>
+#include <mach/pxa3xx_nand.h>
 
 #include "generic.h"
 #include "devices.h"
@@ -95,10 +96,13 @@ static void colibri_pxa3xx_mci_exit(struct device *dev, void *data)
 }
 
 static struct pxamci_platform_data colibri_pxa3xx_mci_platform_data = {
-	.detect_delay	= 20,
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.init		= colibri_pxa3xx_mci_init,
-	.exit		= colibri_pxa3xx_mci_exit,
+	.detect_delay		= 20,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.init			= colibri_pxa3xx_mci_init,
+	.exit			= colibri_pxa3xx_mci_exit,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 void __init colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin)
@@ -154,3 +158,43 @@ void __init colibri_pxa3xx_init_lcd(int bl_pin)
 }
 #endif
 
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+static struct mtd_partition colibri_nand_partitions[] = {
+	{
+		.name        = "bootloader",
+		.offset      = 0,
+		.size        = SZ_512K,
+		.mask_flags  = MTD_WRITEABLE, /* force read-only */
+	},
+	{
+		.name        = "kernel",
+		.offset      = MTDPART_OFS_APPEND,
+		.size        = SZ_4M,
+		.mask_flags  = MTD_WRITEABLE, /* force read-only */
+	},
+	{
+		.name        = "reserved",
+		.offset      = MTDPART_OFS_APPEND,
+		.size        = SZ_1M,
+		.mask_flags  = MTD_WRITEABLE, /* force read-only */
+	},
+	{
+		.name        = "fs",
+		.offset      = MTDPART_OFS_APPEND,
+		.size        = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct pxa3xx_nand_platform_data colibri_nand_info = {
+	.enable_arbiter	= 1,
+	.keep_config	= 1,
+	.parts		= colibri_nand_partitions,
+	.nr_parts	= ARRAY_SIZE(colibri_nand_partitions),
+};
+
+void __init colibri_pxa3xx_init_nand(void)
+{
+	pxa3xx_set_nand_info(&colibri_nand_info);
+}
+#endif
+

arch/arm/mach-pxa/corgi.c

@@ -29,6 +29,7 @@
 #include <linux/spi/ads7846.h>
 #include <linux/spi/corgi_lcd.h>
 #include <linux/mtd/sharpsl.h>
+#include <linux/input/matrix_keypad.h>
 #include <video/w100fb.h>
 
 #include <asm/setup.h>
@@ -104,6 +105,28 @@ static unsigned long corgi_pin_config[] __initdata = {
 	GPIO6_MMC_CLK,
 	GPIO8_MMC_CS0,
 
+	/* GPIO Matrix Keypad */
+	GPIO66_GPIO,	/* column 0 */
+	GPIO67_GPIO,	/* column 1 */
+	GPIO68_GPIO,	/* column 2 */
+	GPIO69_GPIO,	/* column 3 */
+	GPIO70_GPIO,	/* column 4 */
+	GPIO71_GPIO,	/* column 5 */
+	GPIO72_GPIO,	/* column 6 */
+	GPIO73_GPIO,	/* column 7 */
+	GPIO74_GPIO,	/* column 8 */
+	GPIO75_GPIO,	/* column 9 */
+	GPIO76_GPIO,	/* column 10 */
+	GPIO77_GPIO,	/* column 11 */
+	GPIO58_GPIO,	/* row 0 */
+	GPIO59_GPIO,	/* row 1 */
+	GPIO60_GPIO,	/* row 2 */
+	GPIO61_GPIO,	/* row 3 */
+	GPIO62_GPIO,	/* row 4 */
+	GPIO63_GPIO,	/* row 5 */
+	GPIO64_GPIO,	/* row 6 */
+	GPIO65_GPIO,	/* row 7 */
+
 	/* GPIO */
 	GPIO9_GPIO,	/* CORGI_GPIO_nSD_DETECT */
 	GPIO7_GPIO,	/* CORGI_GPIO_nSD_WP */
@@ -267,9 +290,115 @@ static struct platform_device corgifb_device = {
 /*
  * Corgi Keyboard Device
  */
+#define CORGI_KEY_CALENDER	KEY_F1
+#define CORGI_KEY_ADDRESS	KEY_F2
+#define CORGI_KEY_FN		KEY_F3
+#define CORGI_KEY_CANCEL	KEY_F4
+#define CORGI_KEY_OFF		KEY_SUSPEND
+#define CORGI_KEY_EXOK		KEY_F5
+#define CORGI_KEY_EXCANCEL	KEY_F6
+#define CORGI_KEY_EXJOGDOWN	KEY_F7
+#define CORGI_KEY_EXJOGUP	KEY_F8
+#define CORGI_KEY_JAP1		KEY_LEFTCTRL
+#define CORGI_KEY_JAP2		KEY_LEFTALT
+#define CORGI_KEY_MAIL		KEY_F10
+#define CORGI_KEY_OK		KEY_F11
+#define CORGI_KEY_MENU		KEY_F12
+
+static const uint32_t corgikbd_keymap[] = {
+	KEY(0, 1, KEY_1),
+	KEY(0, 2, KEY_3),
+	KEY(0, 3, KEY_5),
+	KEY(0, 4, KEY_6),
+	KEY(0, 5, KEY_7),
+	KEY(0, 6, KEY_9),
+	KEY(0, 7, KEY_0),
+	KEY(0, 8, KEY_BACKSPACE),
+	KEY(1, 1, KEY_2),
+	KEY(1, 2, KEY_4),
+	KEY(1, 3, KEY_R),
+	KEY(1, 4, KEY_Y),
+	KEY(1, 5, KEY_8),
+	KEY(1, 6, KEY_I),
+	KEY(1, 7, KEY_O),
+	KEY(1, 8, KEY_P),
+	KEY(2, 0, KEY_TAB),
+	KEY(2, 1, KEY_Q),
+	KEY(2, 2, KEY_E),
+	KEY(2, 3, KEY_T),
+	KEY(2, 4, KEY_G),
+	KEY(2, 5, KEY_U),
+	KEY(2, 6, KEY_J),
+	KEY(2, 7, KEY_K),
+	KEY(3, 0, CORGI_KEY_CALENDER),
+	KEY(3, 1, KEY_W),
+	KEY(3, 2, KEY_S),
+	KEY(3, 3, KEY_F),
+	KEY(3, 4, KEY_V),
+	KEY(3, 5, KEY_H),
+	KEY(3, 6, KEY_M),
+	KEY(3, 7, KEY_L),
+	KEY(3, 9, KEY_RIGHTSHIFT),
+	KEY(4, 0, CORGI_KEY_ADDRESS),
+	KEY(4, 1, KEY_A),
+	KEY(4, 2, KEY_D),
+	KEY(4, 3, KEY_C),
+	KEY(4, 4, KEY_B),
+	KEY(4, 5, KEY_N),
+	KEY(4, 6, KEY_DOT),
+	KEY(4, 8, KEY_ENTER),
+	KEY(4, 10, KEY_LEFTSHIFT),
+	KEY(5, 0, CORGI_KEY_MAIL),
+	KEY(5, 1, KEY_Z),
+	KEY(5, 2, KEY_X),
+	KEY(5, 3, KEY_MINUS),
+	KEY(5, 4, KEY_SPACE),
+	KEY(5, 5, KEY_COMMA),
+	KEY(5, 7, KEY_UP),
+	KEY(5, 11, CORGI_KEY_FN),
+	KEY(6, 0, KEY_SYSRQ),
+	KEY(6, 1, CORGI_KEY_JAP1),
+	KEY(6, 2, CORGI_KEY_JAP2),
+	KEY(6, 3, CORGI_KEY_CANCEL),
+	KEY(6, 4, CORGI_KEY_OK),
+	KEY(6, 5, CORGI_KEY_MENU),
+	KEY(6, 6, KEY_LEFT),
+	KEY(6, 7, KEY_DOWN),
+	KEY(6, 8, KEY_RIGHT),
+	KEY(7, 0, CORGI_KEY_OFF),
+	KEY(7, 1, CORGI_KEY_EXOK),
+	KEY(7, 2, CORGI_KEY_EXCANCEL),
+	KEY(7, 3, CORGI_KEY_EXJOGDOWN),
+	KEY(7, 4, CORGI_KEY_EXJOGUP),
+};
+
+static struct matrix_keymap_data corgikbd_keymap_data = {
+	.keymap		= corgikbd_keymap,
+	.keymap_size	= ARRAY_SIZE(corgikbd_keymap),
+};
+
+static const int corgikbd_row_gpios[] =
+		{ 58, 59, 60, 61, 62, 63, 64, 65 };
+static const int corgikbd_col_gpios[] =
+		{ 66, 67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77 };
+
+static struct matrix_keypad_platform_data corgikbd_pdata = {
+	.keymap_data		= &corgikbd_keymap_data,
+	.row_gpios		= corgikbd_row_gpios,
+	.col_gpios		= corgikbd_col_gpios,
+	.num_row_gpios		= ARRAY_SIZE(corgikbd_row_gpios),
+	.num_col_gpios		= ARRAY_SIZE(corgikbd_col_gpios),
+	.col_scan_delay_us	= 10,
+	.debounce_ms		= 10,
+	.wakeup			= 1,
+};
+
 static struct platform_device corgikbd_device = {
-	.name		= "corgi-keyboard",
+	.name		= "matrix-keypad",
 	.id		= -1,
+	.dev		= {
+		.platform_data = &corgikbd_pdata,
+	},
 };
 
 /*
@@ -307,111 +436,20 @@ static struct platform_device corgiled_device = {
  * The card detect interrupt isn't debounced so we delay it by 250ms
  * to give the card a chance to fully insert/eject.
  */
-static struct pxamci_platform_data corgi_mci_platform_data;
-
-static int corgi_mci_init(struct device *dev, irq_handler_t corgi_detect_int, void *data)
-{
-	int err;
-
-	err = gpio_request(CORGI_GPIO_nSD_DETECT, "nSD_DETECT");
-	if (err)
-		goto err_out;
-
-	err = gpio_request(CORGI_GPIO_nSD_WP, "nSD_WP");
-	if (err)
-		goto err_free_1;
-
-	err = gpio_request(CORGI_GPIO_SD_PWR, "SD_PWR");
-	if (err)
-		goto err_free_2;
-
-	gpio_direction_input(CORGI_GPIO_nSD_DETECT);
-	gpio_direction_input(CORGI_GPIO_nSD_WP);
-	gpio_direction_output(CORGI_GPIO_SD_PWR, 0);
-
-	corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
-	err = request_irq(CORGI_IRQ_GPIO_nSD_DETECT, corgi_detect_int,
-				IRQF_DISABLED | IRQF_TRIGGER_RISING |
-				IRQF_TRIGGER_FALLING,
-				"MMC card detect", data);
-	if (err) {
-		pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
-				__func__);
-		goto err_free_3;
-	}
-	return 0;
-
-err_free_3:
-	gpio_free(CORGI_GPIO_SD_PWR);
-err_free_2:
-	gpio_free(CORGI_GPIO_nSD_WP);
-err_free_1:
-	gpio_free(CORGI_GPIO_nSD_DETECT);
-err_out:
-	return err;
-}
-
-static void corgi_mci_setpower(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data* p_d = dev->platform_data;
-
-	gpio_set_value(CORGI_GPIO_SD_PWR, ((1 << vdd) & p_d->ocr_mask));
-}
-
-static int corgi_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(CORGI_GPIO_nSD_WP);
-}
-
-static void corgi_mci_exit(struct device *dev, void *data)
-{
-	free_irq(CORGI_IRQ_GPIO_nSD_DETECT, data);
-	gpio_free(CORGI_GPIO_SD_PWR);
-	gpio_free(CORGI_GPIO_nSD_WP);
-	gpio_free(CORGI_GPIO_nSD_DETECT);
-}
-
 static struct pxamci_platform_data corgi_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init 		= corgi_mci_init,
-	.get_ro		= corgi_mci_get_ro,
-	.setpower 	= corgi_mci_setpower,
-	.exit		= corgi_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= CORGI_GPIO_nSD_WP,
+	.gpio_power		= CORGI_GPIO_SD_PWR,
 };
 
 
 /*
  * Irda
  */
-static void corgi_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(CORGI_GPIO_IR_ON, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int corgi_irda_startup(struct device *dev)
-{
-	int err;
-
-	err = gpio_request(CORGI_GPIO_IR_ON, "IR_ON");
-	if (err)
-		return err;
-
-	gpio_direction_output(CORGI_GPIO_IR_ON, 1);
-	return 0;
-}
-
-static void corgi_irda_shutdown(struct device *dev)
-{
-	gpio_free(CORGI_GPIO_IR_ON);
-}
-
 static struct pxaficp_platform_data corgi_ficp_platform_data = {
+	.gpio_pwdown		= CORGI_GPIO_IR_ON,
 	.transceiver_cap	= IR_SIRMODE | IR_OFF,
-	.transceiver_mode	= corgi_irda_transceiver_mode,
-	.startup		= corgi_irda_startup,
-	.shutdown		= corgi_irda_shutdown,
 };
 
 
@@ -636,6 +674,7 @@ static void __init corgi_init(void)
 	corgi_init_spi();
 
  	pxa_set_udc_info(&udc_info);
+	corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250);
 	pxa_set_mci_info(&corgi_mci_platform_data);
 	pxa_set_ficp_info(&corgi_ficp_platform_data);
 	pxa_set_i2c_info(NULL);

arch/arm/mach-pxa/csb726.c

@@ -130,61 +130,17 @@ static struct pxamci_platform_data csb726_mci_data;
 static int csb726_mci_init(struct device *dev,
 		irq_handler_t detect, void *data)
 {
-	int err;
-
 	csb726_mci_data.detect_delay = msecs_to_jiffies(500);
-
-	err = gpio_request(CSB726_GPIO_MMC_DETECT, "MMC detect");
-	if (err)
-		goto err_det_req;
-
-	err = gpio_direction_input(CSB726_GPIO_MMC_DETECT);
-	if (err)
-		goto err_det_dir;
-
-	err = gpio_request(CSB726_GPIO_MMC_RO, "MMC ro");
-	if (err)
-		goto err_ro_req;
-
-	err = gpio_direction_input(CSB726_GPIO_MMC_RO);
-	if (err)
-		goto err_ro_dir;
-
-	err = request_irq(gpio_to_irq(CSB726_GPIO_MMC_DETECT), detect,
-			IRQF_DISABLED, "MMC card detect", data);
-	if (err)
-		goto err_irq;
-
 	return 0;
-
-err_irq:
-err_ro_dir:
-	gpio_free(CSB726_GPIO_MMC_RO);
-err_ro_req:
-err_det_dir:
-	gpio_free(CSB726_GPIO_MMC_DETECT);
-err_det_req:
-	return err;
-}
-
-static int csb726_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(CSB726_GPIO_MMC_RO);
-}
-
-static void csb726_mci_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(CSB726_GPIO_MMC_DETECT), data);
-	gpio_free(CSB726_GPIO_MMC_RO);
-	gpio_free(CSB726_GPIO_MMC_DETECT);
 }
 
 static struct pxamci_platform_data csb726_mci = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init		= csb726_mci_init,
-	.get_ro		= csb726_mci_get_ro,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.init			= csb726_mci_init,
 	/* FIXME setpower */
-	.exit		= csb726_mci_exit,
+	.gpio_card_detect	= CSB726_GPIO_MMC_DETECT,
+	.gpio_card_ro		= CSB726_GPIO_MMC_RO,
+	.gpio_power		= -1,
 };
 
 static struct pxaohci_platform_data csb726_ohci_platform_data = {

arch/arm/mach-pxa/devices.c

@@ -935,6 +935,33 @@ void __init pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info)
 {
 	pxa_register_device(&pxa3xx_device_nand, info);
 }
+
+static struct resource pxa3xx_resources_gcu[] = {
+	{
+		.start	= 0x54000000,
+		.end	= 0x54000fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= IRQ_GCU,
+		.end	= IRQ_GCU,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static u64 pxa3xx_gcu_dmamask = DMA_BIT_MASK(32);
+
+struct platform_device pxa3xx_device_gcu = {
+	.name		= "pxa3xx-gcu",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(pxa3xx_resources_gcu),
+	.resource	= pxa3xx_resources_gcu,
+	.dev		= {
+		.dma_mask = &pxa3xx_gcu_dmamask,
+		.coherent_dma_mask = 0xffffffff,
+	},
+};
+
 #endif /* CONFIG_PXA3xx */
 
 /* pxa2xx-spi platform-device ID equals respective SSP platform-device ID + 1.

arch/arm/mach-pxa/devices.h

@@ -35,4 +35,6 @@ extern struct platform_device pxa27x_device_pwm1;
 extern struct platform_device pxa3xx_device_nand;
 extern struct platform_device pxa3xx_device_i2c_power;
 
+extern struct platform_device pxa3xx_device_gcu;
+
 void __init pxa_register_device(struct platform_device *dev, void *data);

arch/arm/mach-pxa/e740.c

@@ -199,7 +199,6 @@ static void __init e740_init(void)
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	pxa_set_udc_info(&e7xx_udc_mach_info);
 	pxa_set_ac97_info(NULL);
-	e7xx_irda_init();
 	pxa_set_ficp_info(&e7xx_ficp_platform_data);
 }
 

arch/arm/mach-pxa/e750.c

@@ -200,7 +200,6 @@ static void __init e750_init(void)
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	pxa_set_udc_info(&e7xx_udc_mach_info);
 	pxa_set_ac97_info(NULL);
-	e7xx_irda_init();
 	pxa_set_ficp_info(&e7xx_ficp_platform_data);
 }
 

arch/arm/mach-pxa/em-x270.c

@@ -646,13 +646,16 @@ static int em_x270_mci_get_ro(struct device *dev)
 }
 
 static struct pxamci_platform_data em_x270_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
-			  MMC_VDD_24_25|MMC_VDD_25_26|MMC_VDD_26_27|
-			  MMC_VDD_27_28|MMC_VDD_28_29|MMC_VDD_29_30|
-			  MMC_VDD_30_31|MMC_VDD_31_32,
-	.init 		= em_x270_mci_init,
-	.setpower 	= em_x270_mci_setpower,
-	.exit		= em_x270_mci_exit,
+	.ocr_mask		= MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
+				  MMC_VDD_24_25|MMC_VDD_25_26|MMC_VDD_26_27|
+				  MMC_VDD_27_28|MMC_VDD_28_29|MMC_VDD_29_30|
+				  MMC_VDD_30_31|MMC_VDD_31_32,
+	.init 			= em_x270_mci_init,
+	.setpower 		= em_x270_mci_setpower,
+	.exit			= em_x270_mci_exit,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 static void __init em_x270_init_mmc(void)
@@ -1022,22 +1025,32 @@ static int em_x270_sensor_power(struct device *dev, int on)
 	return 0;
 }
 
-static struct soc_camera_link iclink = {
-	.bus_id	= 0,
-	.power = em_x270_sensor_power,
-};
-
 static struct i2c_board_info em_x270_i2c_cam_info[] = {
 	{
 		I2C_BOARD_INFO("mt9m111", 0x48),
+	},
+};
+
+static struct soc_camera_link iclink = {
+	.bus_id		= 0,
+	.power		= em_x270_sensor_power,
+	.board_info	= &em_x270_i2c_cam_info[0],
+	.i2c_adapter_id	= 0,
+	.module_name	= "mt9m111",
+};
+
+static struct platform_device em_x270_camera = {
+	.name	= "soc-camera-pdrv",
+	.id	= -1,
+	.dev	= {
 		.platform_data = &iclink,
 	},
 };
 
 static void  __init em_x270_init_camera(void)
 {
-	i2c_register_board_info(0, ARRAY_AND_SIZE(em_x270_i2c_cam_info));
 	pxa_set_camera_info(&em_x270_camera_platform_data);
+	platform_device_register(&em_x270_camera);
 }
 #else
 static inline void em_x270_init_camera(void) {}
@@ -1103,6 +1116,7 @@ REGULATOR_CONSUMER(ldo5, NULL, "vcc cam");
 REGULATOR_CONSUMER(ldo10, &pxa_device_mci.dev, "vcc sdio");
 REGULATOR_CONSUMER(ldo12, NULL, "vcc usb");
 REGULATOR_CONSUMER(ldo19, &em_x270_gprs_userspace_consumer.dev, "vcc gprs");
+REGULATOR_CONSUMER(buck2, NULL, "vcc_core");
 
 #define REGULATOR_INIT(_ldo, _min_uV, _max_uV, _ops_mask)		\
 	static struct regulator_init_data _ldo##_data = {		\
@@ -1125,6 +1139,7 @@ REGULATOR_INIT(ldo10, 2000000, 3200000,
 	       REGULATOR_CHANGE_STATUS | REGULATOR_CHANGE_VOLTAGE);
 REGULATOR_INIT(ldo12, 3000000, 3000000, REGULATOR_CHANGE_STATUS);
 REGULATOR_INIT(ldo19, 3200000, 3200000, REGULATOR_CHANGE_STATUS);
+REGULATOR_INIT(buck2, 1000000, 1650000, REGULATOR_CHANGE_VOLTAGE);
 
 struct led_info em_x270_led_info = {
 	.name = "em-x270:orange",
@@ -1194,6 +1209,8 @@ struct da903x_subdev_info em_x270_da9030_subdevs[] = {
 	DA9030_LDO(12),
 	DA9030_LDO(19),
 
+	DA9030_SUBDEV(regulator, BUCK2, &buck2_data),
+
 	DA9030_SUBDEV(led, LED_PC, &em_x270_led_info),
 	DA9030_SUBDEV(backlight, WLED, &em_x270_led_info),
 	DA9030_SUBDEV(battery, BAT, &em_x270_batterty_info),
@@ -1245,7 +1262,6 @@ static void __init em_x270_init_i2c(void)
 
 static void __init em_x270_module_init(void)
 {
-	pr_info("%s\n", __func__);
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(em_x270_pin_config));
 
 	mmc_cd = GPIO13_MMC_CD;
@@ -1257,7 +1273,6 @@ static void __init em_x270_module_init(void)
 
 static void __init em_x270_exeda_init(void)
 {
-	pr_info("%s\n", __func__);
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(exeda_pin_config));
 
 	mmc_cd = GPIO114_MMC_CD;

arch/arm/mach-pxa/eseries.c

@@ -47,44 +47,9 @@ struct pxa2xx_udc_mach_info e7xx_udc_mach_info = {
 	.gpio_pullup_inverted = 1
 };
 
-static void e7xx_irda_transceiver_mode(struct device *dev, int mode)
-{
-	if (mode & IR_OFF) {
-		gpio_set_value(GPIO_E7XX_IR_OFF, 1);
-		pxa2xx_transceiver_mode(dev, mode);
-	} else {
-		pxa2xx_transceiver_mode(dev, mode);
-		gpio_set_value(GPIO_E7XX_IR_OFF, 0);
-	}
-}
-
-int e7xx_irda_init(void)
-{
-	int ret;
-
-	ret = gpio_request(GPIO_E7XX_IR_OFF, "IrDA power");
-	if (ret)
-		goto out;
-
-	ret = gpio_direction_output(GPIO_E7XX_IR_OFF, 0);
-	if (ret)
-		goto out;
-
-	e7xx_irda_transceiver_mode(NULL, IR_SIRMODE | IR_OFF);
-out:
-	return ret;
-}
-
-static void e7xx_irda_shutdown(struct device *dev)
-{
-	e7xx_irda_transceiver_mode(dev, IR_SIRMODE | IR_OFF);
-	gpio_free(GPIO_E7XX_IR_OFF);
-}
-
 struct pxaficp_platform_data e7xx_ficp_platform_data = {
-	.transceiver_cap  = IR_SIRMODE | IR_OFF,
-	.transceiver_mode = e7xx_irda_transceiver_mode,
-	.shutdown = e7xx_irda_shutdown,
+	.gpio_pwdown		= GPIO_E7XX_IR_OFF,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 int eseries_tmio_enable(struct platform_device *dev)

arch/arm/mach-pxa/gumstix.c

@@ -88,7 +88,10 @@ static struct platform_device *devices[] __initdata = {
 
 #ifdef CONFIG_MMC_PXA
 static struct pxamci_platform_data gumstix_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.gpio_card_detect 	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 static void __init gumstix_mmc_init(void)

arch/arm/mach-pxa/hx4700.c

@@ -45,6 +45,7 @@
 #include <mach/irda.h>
 #include <mach/pxa2xx_spi.h>
 
+#include <video/platform_lcd.h>
 #include <video/w100fb.h>
 
 #include "devices.h"
@@ -174,14 +175,9 @@ static int hx4700_gpio_request(struct gpio_ress *gpios, int size)
  * IRDA
  */
 
-static void irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO105_HX4700_nIR_ON, mode & IR_OFF);
-}
-
 static struct pxaficp_platform_data ficp_info = {
-	.transceiver_cap  = IR_SIRMODE | IR_OFF,
-	.transceiver_mode = irda_transceiver_mode,
+	.gpio_pwdown		= GPIO105_HX4700_nIR_ON,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 /*
@@ -368,8 +364,6 @@ static struct platform_device egpio = {
  * LCD - Sony display connected to ATI Imageon w3220
  */
 
-static int lcd_power;
-
 static void sony_lcd_init(void)
 {
 	gpio_set_value(GPIO84_HX4700_LCD_SQN, 1);
@@ -410,35 +404,6 @@ static void sony_lcd_off(void)
 	gpio_set_value(GPIO110_HX4700_LCD_LVDD_3V3_ON, 0);
 }
 
-static int hx4700_lcd_set_power(struct lcd_device *ldev, int level)
-{
-	switch (level) {
-	case FB_BLANK_UNBLANK:
-		sony_lcd_init();
-		break;
-	case FB_BLANK_NORMAL:
-	case FB_BLANK_VSYNC_SUSPEND:
-	case FB_BLANK_HSYNC_SUSPEND:
-	case FB_BLANK_POWERDOWN:
-		sony_lcd_off();
-		break;
-	}
-	lcd_power = level;
-	return 0;
-}
-
-static int hx4700_lcd_get_power(struct lcd_device *lm)
-{
-	return lcd_power;
-}
-
-static struct lcd_ops hx4700_lcd_ops = {
-	.get_power = hx4700_lcd_get_power,
-	.set_power = hx4700_lcd_set_power,
-};
-
-static struct lcd_device *hx4700_lcd_device;
-
 #ifdef CONFIG_PM
 static void w3220_lcd_suspend(struct w100fb_par *wfb)
 {
@@ -573,6 +538,27 @@ static struct platform_device w3220 = {
 	.resource      = w3220_resources,
 };
 
+static void hx4700_lcd_set_power(struct plat_lcd_data *pd, unsigned int power)
+{
+	if (power)
+		sony_lcd_init();
+	else
+		sony_lcd_off();
+}
+
+static struct plat_lcd_data hx4700_lcd_data = {
+	.set_power = hx4700_lcd_set_power,
+};
+
+static struct platform_device hx4700_lcd = {
+	.name = "platform-lcd",
+	.id   = -1,
+	.dev  = {
+		.platform_data = &hx4700_lcd_data,
+		.parent        = &w3220.dev,
+	},
+};
+
 /*
  * Backlight
  */
@@ -872,9 +858,6 @@ static void __init hx4700_init(void)
 	pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
 	spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info));
 
-	hx4700_lcd_device = lcd_device_register("w100fb", NULL,
-					(void *)&w3220_info, &hx4700_lcd_ops);
-
 	gpio_set_value(GPIO71_HX4700_ASIC3_nRESET, 0);
 	mdelay(10);
 	gpio_set_value(GPIO71_HX4700_ASIC3_nRESET, 1);

arch/arm/mach-pxa/idp.c

@@ -168,7 +168,10 @@ static struct pxafb_mach_info sharp_lm8v31 = {
 };
 
 static struct pxamci_platform_data idp_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 static void __init idp_init(void)

arch/arm/mach-pxa/imote2.c

@@ -389,6 +389,9 @@ static int imote2_mci_get_ro(struct device *dev)
 static struct pxamci_platform_data imote2_mci_platform_data = {
 	.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* default anyway */
 	.get_ro = imote2_mci_get_ro,
+	.gpio_card_detect = -1,
+	.gpio_card_ro	= -1,
+	.gpio_power = -1,
 };
 
 static struct mtd_partition imote2flash_partitions[] = {

arch/arm/mach-pxa/include/mach/balloon3.h

@@ -0,0 +1,134 @@
+/*
+ *  linux/include/asm-arm/arch-pxa/balloon3.h
+ *
+ *  Authors:	Nick Bane and Wookey
+ *  Created:	Oct, 2005
+ *  Copyright:	Toby Churchill Ltd
+ *  Cribbed from mainstone.c, by Nicholas Pitre
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef ASM_ARCH_BALLOON3_H
+#define ASM_ARCH_BALLOON3_H
+
+enum balloon3_features {
+	BALLOON3_FEATURE_OHCI,
+	BALLOON3_FEATURE_MMC,
+	BALLOON3_FEATURE_CF,
+	BALLOON3_FEATURE_AUDIO,
+	BALLOON3_FEATURE_TOPPOLY,
+};
+
+#define BALLOON3_FPGA_PHYS	PXA_CS4_PHYS
+#define BALLOON3_FPGA_VIRT	(0xf1000000)	/* as per balloon2 */
+#define BALLOON3_FPGA_LENGTH	0x01000000
+
+/* FPGA/CPLD registers */
+#define BALLOON3_PCMCIA0_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)
+/* fixme - same for now */
+#define BALLOON3_PCMCIA1_REG		(BALLOON3_FPGA_VIRT + 0x00e00008)
+#define BALLOON3_NANDIO_IO_REG		(BALLOON3_FPGA_VIRT + 0x00e00000)
+/* fpga/cpld interrupt control register */
+#define BALLOON3_INT_CONTROL_REG	(BALLOON3_FPGA_VIRT + 0x00e0000C)
+#define BALLOON3_NANDIO_CTL2_REG 	(BALLOON3_FPGA_VIRT + 0x00e00010)
+#define BALLOON3_NANDIO_CTL_REG 	(BALLOON3_FPGA_VIRT + 0x00e00014)
+#define BALLOON3_VERSION_REG		(BALLOON3_FPGA_VIRT + 0x00e0001c)
+
+#define BALLOON3_SAMOSA_ADDR_REG	(BALLOON3_FPGA_VIRT + 0x00c00000)
+#define BALLOON3_SAMOSA_DATA_REG	(BALLOON3_FPGA_VIRT + 0x00c00004)
+#define BALLOON3_SAMOSA_STATUS_REG	(BALLOON3_FPGA_VIRT + 0x00c0001c)
+
+/* GPIOs for irqs */
+#define BALLOON3_GPIO_AUX_NIRQ		(94)
+#define BALLOON3_GPIO_CODEC_IRQ		(95)
+
+/* Timer and Idle LED locations */
+#define BALLOON3_GPIO_LED_NAND		(9)
+#define BALLOON3_GPIO_LED_IDLE		(10)
+
+/* backlight control */
+#define BALLOON3_GPIO_RUN_BACKLIGHT	(99)
+
+#define BALLOON3_GPIO_S0_CD		(105)
+
+/* FPGA Interrupt Mask/Acknowledge Register */
+#define BALLOON3_INT_S0_IRQ		(1 << 0)  /* PCMCIA 0 IRQ */
+#define BALLOON3_INT_S0_STSCHG		(1 << 1)  /* PCMCIA 0 status changed */
+
+/* CF Status Register */
+#define BALLOON3_PCMCIA_nIRQ		(1 << 0)  /* IRQ / ready signal */
+#define BALLOON3_PCMCIA_nSTSCHG_BVD1	(1 << 1)
+					/* VDD sense / card status changed */
+
+/* CF control register (write) */
+#define BALLOON3_PCMCIA_RESET		(1 << 0)   /* Card reset signal */
+#define BALLOON3_PCMCIA_ENABLE		(1 << 1)
+#define BALLOON3_PCMCIA_ADD_ENABLE	(1 << 2)
+
+/* CPLD (and FPGA) interface definitions */
+#define CPLD_LCD0_DATA_SET             0x00
+#define CPLD_LCD0_DATA_CLR             0x10
+#define CPLD_LCD0_COMMAND_SET          0x01
+#define CPLD_LCD0_COMMAND_CLR          0x11
+#define CPLD_LCD1_DATA_SET             0x02
+#define CPLD_LCD1_DATA_CLR             0x12
+#define CPLD_LCD1_COMMAND_SET          0x03
+#define CPLD_LCD1_COMMAND_CLR          0x13
+
+#define CPLD_MISC_SET                  0x07
+#define CPLD_MISC_CLR                  0x17
+#define CPLD_MISC_LOON_NRESET_BIT      0
+#define CPLD_MISC_LOON_UNSUSP_BIT      1
+#define CPLD_MISC_RUN_5V_BIT           2
+#define CPLD_MISC_CHG_D0_BIT           3
+#define CPLD_MISC_CHG_D1_BIT           4
+#define CPLD_MISC_DAC_NCS_BIT          5
+
+#define CPLD_LCD_SET                   0x08
+#define CPLD_LCD_CLR                   0x18
+#define CPLD_LCD_BACKLIGHT_EN_0_BIT    0
+#define CPLD_LCD_BACKLIGHT_EN_1_BIT    1
+#define CPLD_LCD_LED_RED_BIT           4
+#define CPLD_LCD_LED_GREEN_BIT         5
+#define CPLD_LCD_NRESET_BIT            7
+
+#define CPLD_LCD_RO_SET                0x09
+#define CPLD_LCD_RO_CLR                0x19
+#define CPLD_LCD_RO_LCD0_nWAIT_BIT     0
+#define CPLD_LCD_RO_LCD1_nWAIT_BIT     1
+
+#define CPLD_SERIAL_SET                0x0a
+#define CPLD_SERIAL_CLR                0x1a
+#define CPLD_SERIAL_GSM_RI_BIT         0
+#define CPLD_SERIAL_GSM_CTS_BIT        1
+#define CPLD_SERIAL_GSM_DTR_BIT        2
+#define CPLD_SERIAL_LPR_CTS_BIT        3
+#define CPLD_SERIAL_TC232_CTS_BIT      4
+#define CPLD_SERIAL_TC232_DSR_BIT      5
+
+#define CPLD_SROUTING_SET              0x0b
+#define CPLD_SROUTING_CLR              0x1b
+#define CPLD_SROUTING_MSP430_LPR       0
+#define CPLD_SROUTING_MSP430_TC232     1
+#define CPLD_SROUTING_MSP430_GSM       2
+#define CPLD_SROUTING_LOON_LPR         (0 << 4)
+#define CPLD_SROUTING_LOON_TC232       (1 << 4)
+#define CPLD_SROUTING_LOON_GSM         (2 << 4)
+
+#define CPLD_AROUTING_SET              0x0c
+#define CPLD_AROUTING_CLR              0x1c
+#define CPLD_AROUTING_MIC2PHONE_BIT    0
+#define CPLD_AROUTING_PHONE2INT_BIT    1
+#define CPLD_AROUTING_PHONE2EXT_BIT    2
+#define CPLD_AROUTING_LOONL2INT_BIT    3
+#define CPLD_AROUTING_LOONL2EXT_BIT    4
+#define CPLD_AROUTING_LOONR2PHONE_BIT  5
+#define CPLD_AROUTING_LOONR2INT_BIT    6
+#define CPLD_AROUTING_LOONR2EXT_BIT    7
+
+extern int balloon3_has(enum balloon3_features feature);
+
+#endif

arch/arm/mach-pxa/include/mach/colibri.h

@@ -23,6 +23,12 @@ static inline void colibri_pxa3xx_init_lcd(int bl_pin) {}
 extern void colibri_pxa3xx_init_eth(struct ax_plat_data *plat_data);
 #endif
 
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+extern void colibri_pxa3xx_init_nand(void);
+#else
+static inline void colibri_pxa3xx_init_nand(void) {}
+#endif
+
 /* physical memory regions */
 #define COLIBRI_SDRAM_BASE	0xa0000000      /* SDRAM region */
 

arch/arm/mach-pxa/include/mach/entry-macro.S

@@ -24,34 +24,27 @@
 		mov	\tmp, \tmp, lsr #13
 		and	\tmp, \tmp, #0x7		@ Core G
 		cmp	\tmp, #1
-		bhi	1004f
+		bhi	1002f
 
+		@ Core Generation 1 (PXA25x)
 		mov	\base, #io_p2v(0x40000000)	@ IIR Ctl = 0x40d00000
 		add	\base, \base, #0x00d00000
 		ldr	\irqstat, [\base, #0]		@ ICIP
 		ldr	\irqnr, [\base, #4]		@ ICMR
-		b	1002f
 
-1004:
-		mrc	p6, 0, \irqstat, c6, c0, 0	@ ICIP2
-		mrc	p6, 0, \irqnr, c7, c0, 0	@ ICMR2
 		ands	\irqnr, \irqstat, \irqnr
-		beq	1003f
+		beq	1001f
 		rsb	\irqstat, \irqnr, #0
 		and	\irqstat, \irqstat, \irqnr
 		clz	\irqnr, \irqstat
-		rsb	\irqnr, \irqnr, #31
-		add	\irqnr, \irqnr, #(32 + PXA_IRQ(0))
+		rsb	\irqnr, \irqnr, #(31 + PXA_IRQ(0))
 		b	1001f
-1003:
-		mrc	p6, 0, \irqstat, c0, c0, 0	@ ICIP
-		mrc	p6, 0, \irqnr, c1, c0, 0	@ ICMR
 1002:
-		ands	\irqnr, \irqstat, \irqnr
+		@ Core Generation 2 (PXA27x) or Core Generation 3 (PXA3xx)
+		mrc	p6, 0, \irqstat, c5, c0, 0	@ ICHP
+		tst	\irqstat, #0x80000000
 		beq	1001f
-		rsb	\irqstat, \irqnr, #0
-		and	\irqstat, \irqstat, \irqnr
-		clz	\irqnr, \irqstat
-		rsb	\irqnr, \irqnr, #(31 + PXA_IRQ(0))
+		bic	\irqstat, \irqstat, #0x80000000
+		mov	\irqnr, \irqstat, lsr #16
 1001:
 		.endm

arch/arm/mach-pxa/include/mach/hardware.h

@@ -197,6 +197,16 @@
 #define __cpu_is_pxa935(id)	(0)
 #endif
 
+#ifdef CONFIG_CPU_PXA950
+#define __cpu_is_pxa950(id)                             \
+	({                                              \
+		unsigned int _id = (id) >> 4 & 0xfff;	\
+		id == 0x697;				\
+	 })
+#else
+#define __cpu_is_pxa950(id)	(0)
+#endif
+
 #define cpu_is_pxa210()					\
 	({						\
 		__cpu_is_pxa210(read_cpuid_id());	\
@@ -249,6 +259,13 @@
 		__cpu_is_pxa935(id);			\
 	 })
 
+#define cpu_is_pxa950()					\
+	({						\
+		unsigned int id = read_cpuid(CPUID_ID);	\
+		__cpu_is_pxa950(id);			\
+	 })
+
+
 /*
  * CPUID Core Generation Bit
  * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x

arch/arm/mach-pxa/include/mach/irda.h

@@ -12,6 +12,8 @@ struct pxaficp_platform_data {
 	void (*transceiver_mode)(struct device *dev, int mode);
 	int (*startup)(struct device *dev);
 	void (*shutdown)(struct device *dev);
+	int gpio_pwdown;		/* powerdown GPIO for the IrDA chip */
+	bool gpio_pwdown_inverted;	/* gpio_pwdown is inverted */
 };
 
 extern void pxa_set_ficp_info(struct pxaficp_platform_data *info);

arch/arm/mach-pxa/include/mach/irqs.h

@@ -68,9 +68,10 @@
 #ifdef CONFIG_PXA3xx
 #define IRQ_SSP4	PXA_IRQ(13)	/* SSP4 service request */
 #define IRQ_CIR		PXA_IRQ(34)	/* Consumer IR */
+#define IRQ_COMM_WDT	PXA_IRQ(35) 	/* Comm WDT interrupt */
 #define IRQ_TSI		PXA_IRQ(36)	/* Touch Screen Interface (PXA320) */
 #define IRQ_USIM2	PXA_IRQ(38)	/* USIM2 Controller */
-#define IRQ_GRPHICS	PXA_IRQ(39)	/* Graphics Controller */
+#define IRQ_GCU		PXA_IRQ(39)	/* Graphics Controller */
 #define IRQ_MMC2	PXA_IRQ(41)	/* MMC2 Controller */
 #define IRQ_1WIRE	PXA_IRQ(44)	/* 1-Wire Controller */
 #define IRQ_NAND	PXA_IRQ(45)	/* NAND Controller */
@@ -81,8 +82,31 @@
 #define IRQ_MMC3	PXA_IRQ(55)	/* MMC3 Controller (PXA310) */
 #endif
 
-#define PXA_GPIO_IRQ_BASE	PXA_IRQ(64)
-#define PXA_GPIO_IRQ_NUM	(128)
+#ifdef CONFIG_CPU_PXA935
+#define IRQ_U2O		PXA_IRQ(64)	/* USB OTG 2.0 Controller (PXA935) */
+#define IRQ_U2H		PXA_IRQ(65)	/* USB Host 2.0 Controller (PXA935) */
+
+#define IRQ_MMC3_PXA935	PXA_IRQ(72)	/* MMC3 Controller (PXA935) */
+#define IRQ_MMC4_PXA935	PXA_IRQ(73)	/* MMC4 Controller (PXA935) */
+#define IRQ_MMC5_PXA935	PXA_IRQ(74)	/* MMC5 Controller (PXA935) */
+
+#define IRQ_U2P		PXA_IRQ(93)	/* USB PHY D+/D- Lines (PXA935) */
+#endif
+
+#ifdef CONFIG_CPU_PXA930
+#define IRQ_ENHROT	PXA_IRQ(37)	/* Enhanced Rotary (PXA930) */
+#define IRQ_ACIPC0	PXA_IRQ(5)
+#define IRQ_ACIPC1	PXA_IRQ(40)
+#define IRQ_ACIPC2	PXA_IRQ(19)
+#define IRQ_TRKBALL	PXA_IRQ(43)	/* Track Ball */
+#endif
+
+#ifdef CONFIG_CPU_PXA950
+#define IRQ_GC500	PXA_IRQ(70)	/* Graphics Controller (PXA950) */
+#endif
+
+#define PXA_GPIO_IRQ_BASE	PXA_IRQ(96)
+#define PXA_GPIO_IRQ_NUM	(192)
 
 #define GPIO_2_x_TO_IRQ(x)	(PXA_GPIO_IRQ_BASE + (x))
 #define IRQ_GPIO(x)	(((x) < 2) ? (IRQ_GPIO0 + (x)) : GPIO_2_x_TO_IRQ(x))
@@ -105,6 +129,8 @@
 #define IRQ_BOARD_END		(IRQ_BOARD_START + 70)
 #elif defined(CONFIG_MACH_ZYLONITE)
 #define IRQ_BOARD_END		(IRQ_BOARD_START + 32)
+#elif defined(CONFIG_PXA_EZX)
+#define IRQ_BOARD_END		(IRQ_BOARD_START + 23)
 #else
 #define IRQ_BOARD_END		(IRQ_BOARD_START + 16)
 #endif
@@ -237,6 +263,16 @@
 #define MAINSTONE_S1_STSCHG_IRQ	MAINSTONE_IRQ(14)
 #define MAINSTONE_S1_IRQ	MAINSTONE_IRQ(15)
 
+/* Balloon3 Interrupts */
+#define BALLOON3_IRQ(x)		(IRQ_BOARD_START + (x))
+
+#define BALLOON3_BP_CF_NRDY_IRQ	BALLOON3_IRQ(0)
+#define BALLOON3_BP_NSTSCHG_IRQ	BALLOON3_IRQ(1)
+
+#define BALLOON3_AUX_NIRQ	IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ)
+#define BALLOON3_CODEC_IRQ	IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ)
+#define BALLOON3_S0_CD_IRQ	IRQ_GPIO(BALLOON3_GPIO_S0_CD)
+
 /* LoCoMo Interrupts (CONFIG_SHARP_LOCOMO) */
 #define IRQ_LOCOMO_KEY_BASE	(IRQ_BOARD_START + 0)
 #define IRQ_LOCOMO_GPIO_BASE	(IRQ_BOARD_START + 1)

arch/arm/mach-pxa/include/mach/mfp.h

@@ -16,305 +16,6 @@
 #ifndef __ASM_ARCH_MFP_H
 #define __ASM_ARCH_MFP_H
 
-#define mfp_to_gpio(m)	((m) % 128)
-
-/* list of all the configurable MFP pins */
-enum {
-	MFP_PIN_INVALID = -1,
-
-	MFP_PIN_GPIO0 = 0,
-	MFP_PIN_GPIO1,
-	MFP_PIN_GPIO2,
-	MFP_PIN_GPIO3,
-	MFP_PIN_GPIO4,
-	MFP_PIN_GPIO5,
-	MFP_PIN_GPIO6,
-	MFP_PIN_GPIO7,
-	MFP_PIN_GPIO8,
-	MFP_PIN_GPIO9,
-	MFP_PIN_GPIO10,
-	MFP_PIN_GPIO11,
-	MFP_PIN_GPIO12,
-	MFP_PIN_GPIO13,
-	MFP_PIN_GPIO14,
-	MFP_PIN_GPIO15,
-	MFP_PIN_GPIO16,
-	MFP_PIN_GPIO17,
-	MFP_PIN_GPIO18,
-	MFP_PIN_GPIO19,
-	MFP_PIN_GPIO20,
-	MFP_PIN_GPIO21,
-	MFP_PIN_GPIO22,
-	MFP_PIN_GPIO23,
-	MFP_PIN_GPIO24,
-	MFP_PIN_GPIO25,
-	MFP_PIN_GPIO26,
-	MFP_PIN_GPIO27,
-	MFP_PIN_GPIO28,
-	MFP_PIN_GPIO29,
-	MFP_PIN_GPIO30,
-	MFP_PIN_GPIO31,
-	MFP_PIN_GPIO32,
-	MFP_PIN_GPIO33,
-	MFP_PIN_GPIO34,
-	MFP_PIN_GPIO35,
-	MFP_PIN_GPIO36,
-	MFP_PIN_GPIO37,
-	MFP_PIN_GPIO38,
-	MFP_PIN_GPIO39,
-	MFP_PIN_GPIO40,
-	MFP_PIN_GPIO41,
-	MFP_PIN_GPIO42,
-	MFP_PIN_GPIO43,
-	MFP_PIN_GPIO44,
-	MFP_PIN_GPIO45,
-	MFP_PIN_GPIO46,
-	MFP_PIN_GPIO47,
-	MFP_PIN_GPIO48,
-	MFP_PIN_GPIO49,
-	MFP_PIN_GPIO50,
-	MFP_PIN_GPIO51,
-	MFP_PIN_GPIO52,
-	MFP_PIN_GPIO53,
-	MFP_PIN_GPIO54,
-	MFP_PIN_GPIO55,
-	MFP_PIN_GPIO56,
-	MFP_PIN_GPIO57,
-	MFP_PIN_GPIO58,
-	MFP_PIN_GPIO59,
-	MFP_PIN_GPIO60,
-	MFP_PIN_GPIO61,
-	MFP_PIN_GPIO62,
-	MFP_PIN_GPIO63,
-	MFP_PIN_GPIO64,
-	MFP_PIN_GPIO65,
-	MFP_PIN_GPIO66,
-	MFP_PIN_GPIO67,
-	MFP_PIN_GPIO68,
-	MFP_PIN_GPIO69,
-	MFP_PIN_GPIO70,
-	MFP_PIN_GPIO71,
-	MFP_PIN_GPIO72,
-	MFP_PIN_GPIO73,
-	MFP_PIN_GPIO74,
-	MFP_PIN_GPIO75,
-	MFP_PIN_GPIO76,
-	MFP_PIN_GPIO77,
-	MFP_PIN_GPIO78,
-	MFP_PIN_GPIO79,
-	MFP_PIN_GPIO80,
-	MFP_PIN_GPIO81,
-	MFP_PIN_GPIO82,
-	MFP_PIN_GPIO83,
-	MFP_PIN_GPIO84,
-	MFP_PIN_GPIO85,
-	MFP_PIN_GPIO86,
-	MFP_PIN_GPIO87,
-	MFP_PIN_GPIO88,
-	MFP_PIN_GPIO89,
-	MFP_PIN_GPIO90,
-	MFP_PIN_GPIO91,
-	MFP_PIN_GPIO92,
-	MFP_PIN_GPIO93,
-	MFP_PIN_GPIO94,
-	MFP_PIN_GPIO95,
-	MFP_PIN_GPIO96,
-	MFP_PIN_GPIO97,
-	MFP_PIN_GPIO98,
-	MFP_PIN_GPIO99,
-	MFP_PIN_GPIO100,
-	MFP_PIN_GPIO101,
-	MFP_PIN_GPIO102,
-	MFP_PIN_GPIO103,
-	MFP_PIN_GPIO104,
-	MFP_PIN_GPIO105,
-	MFP_PIN_GPIO106,
-	MFP_PIN_GPIO107,
-	MFP_PIN_GPIO108,
-	MFP_PIN_GPIO109,
-	MFP_PIN_GPIO110,
-	MFP_PIN_GPIO111,
-	MFP_PIN_GPIO112,
-	MFP_PIN_GPIO113,
-	MFP_PIN_GPIO114,
-	MFP_PIN_GPIO115,
-	MFP_PIN_GPIO116,
-	MFP_PIN_GPIO117,
-	MFP_PIN_GPIO118,
-	MFP_PIN_GPIO119,
-	MFP_PIN_GPIO120,
-	MFP_PIN_GPIO121,
-	MFP_PIN_GPIO122,
-	MFP_PIN_GPIO123,
-	MFP_PIN_GPIO124,
-	MFP_PIN_GPIO125,
-	MFP_PIN_GPIO126,
-	MFP_PIN_GPIO127,
-	MFP_PIN_GPIO0_2,
-	MFP_PIN_GPIO1_2,
-	MFP_PIN_GPIO2_2,
-	MFP_PIN_GPIO3_2,
-	MFP_PIN_GPIO4_2,
-	MFP_PIN_GPIO5_2,
-	MFP_PIN_GPIO6_2,
-	MFP_PIN_GPIO7_2,
-	MFP_PIN_GPIO8_2,
-	MFP_PIN_GPIO9_2,
-	MFP_PIN_GPIO10_2,
-	MFP_PIN_GPIO11_2,
-	MFP_PIN_GPIO12_2,
-	MFP_PIN_GPIO13_2,
-	MFP_PIN_GPIO14_2,
-	MFP_PIN_GPIO15_2,
-	MFP_PIN_GPIO16_2,
-	MFP_PIN_GPIO17_2,
-
-	MFP_PIN_ULPI_STP,
-	MFP_PIN_ULPI_NXT,
-	MFP_PIN_ULPI_DIR,
-
-	MFP_PIN_nXCVREN,
-	MFP_PIN_DF_CLE_nOE,
-	MFP_PIN_DF_nADV1_ALE,
-	MFP_PIN_DF_SCLK_E,
-	MFP_PIN_DF_SCLK_S,
-	MFP_PIN_nBE0,
-	MFP_PIN_nBE1,
-	MFP_PIN_DF_nADV2_ALE,
-	MFP_PIN_DF_INT_RnB,
-	MFP_PIN_DF_nCS0,
-	MFP_PIN_DF_nCS1,
-	MFP_PIN_nLUA,
-	MFP_PIN_nLLA,
-	MFP_PIN_DF_nWE,
-	MFP_PIN_DF_ALE_nWE,
-	MFP_PIN_DF_nRE_nOE,
-	MFP_PIN_DF_ADDR0,
-	MFP_PIN_DF_ADDR1,
-	MFP_PIN_DF_ADDR2,
-	MFP_PIN_DF_ADDR3,
-	MFP_PIN_DF_IO0,
-	MFP_PIN_DF_IO1,
-	MFP_PIN_DF_IO2,
-	MFP_PIN_DF_IO3,
-	MFP_PIN_DF_IO4,
-	MFP_PIN_DF_IO5,
-	MFP_PIN_DF_IO6,
-	MFP_PIN_DF_IO7,
-	MFP_PIN_DF_IO8,
-	MFP_PIN_DF_IO9,
-	MFP_PIN_DF_IO10,
-	MFP_PIN_DF_IO11,
-	MFP_PIN_DF_IO12,
-	MFP_PIN_DF_IO13,
-	MFP_PIN_DF_IO14,
-	MFP_PIN_DF_IO15,
-
-	/* additional pins on PXA930 */
-	MFP_PIN_GSIM_UIO,
-	MFP_PIN_GSIM_UCLK,
-	MFP_PIN_GSIM_UDET,
-	MFP_PIN_GSIM_nURST,
-	MFP_PIN_PMIC_INT,
-	MFP_PIN_RDY,
-
-	MFP_PIN_MAX,
-};
-
-/*
- * a possible MFP configuration is represented by a 32-bit integer
- *
- * bit  0.. 9 - MFP Pin Number (1024 Pins Maximum)
- * bit 10..12 - Alternate Function Selection
- * bit 13..15 - Drive Strength
- * bit 16..18 - Low Power Mode State
- * bit 19..20 - Low Power Mode Edge Detection
- * bit 21..22 - Run Mode Pull State
- *
- * to facilitate the definition, the following macros are provided
- *
- * MFP_CFG_DEFAULT - default MFP configuration value, with
- * 		  alternate function = 0,
- * 		  drive strength = fast 3mA (MFP_DS03X)
- * 		  low power mode = default
- * 		  edge detection = none
- *
- * MFP_CFG	- default MFPR value with alternate function
- * MFP_CFG_DRV	- default MFPR value with alternate function and
- * 		  pin drive strength
- * MFP_CFG_LPM	- default MFPR value with alternate function and
- * 		  low power mode
- * MFP_CFG_X	- default MFPR value with alternate function,
- * 		  pin drive strength and low power mode
- */
-
-typedef unsigned long mfp_cfg_t;
-
-#define MFP_PIN(x)		((x) & 0x3ff)
-
-#define MFP_AF0			(0x0 << 10)
-#define MFP_AF1			(0x1 << 10)
-#define MFP_AF2			(0x2 << 10)
-#define MFP_AF3			(0x3 << 10)
-#define MFP_AF4			(0x4 << 10)
-#define MFP_AF5			(0x5 << 10)
-#define MFP_AF6			(0x6 << 10)
-#define MFP_AF7			(0x7 << 10)
-#define MFP_AF_MASK		(0x7 << 10)
-#define MFP_AF(x)		(((x) >> 10) & 0x7)
-
-#define MFP_DS01X		(0x0 << 13)
-#define MFP_DS02X		(0x1 << 13)
-#define MFP_DS03X		(0x2 << 13)
-#define MFP_DS04X		(0x3 << 13)
-#define MFP_DS06X		(0x4 << 13)
-#define MFP_DS08X		(0x5 << 13)
-#define MFP_DS10X		(0x6 << 13)
-#define MFP_DS13X		(0x7 << 13)
-#define MFP_DS_MASK		(0x7 << 13)
-#define MFP_DS(x)		(((x) >> 13) & 0x7)
-
-#define MFP_LPM_DEFAULT		(0x0 << 16)
-#define MFP_LPM_DRIVE_LOW	(0x1 << 16)
-#define MFP_LPM_DRIVE_HIGH	(0x2 << 16)
-#define MFP_LPM_PULL_LOW	(0x3 << 16)
-#define MFP_LPM_PULL_HIGH	(0x4 << 16)
-#define MFP_LPM_FLOAT		(0x5 << 16)
-#define MFP_LPM_INPUT		(0x6 << 16)
-#define MFP_LPM_STATE_MASK	(0x7 << 16)
-#define MFP_LPM_STATE(x)	(((x) >> 16) & 0x7)
-
-#define MFP_LPM_EDGE_NONE	(0x0 << 19)
-#define MFP_LPM_EDGE_RISE	(0x1 << 19)
-#define MFP_LPM_EDGE_FALL	(0x2 << 19)
-#define MFP_LPM_EDGE_BOTH	(0x3 << 19)
-#define MFP_LPM_EDGE_MASK	(0x3 << 19)
-#define MFP_LPM_EDGE(x)		(((x) >> 19) & 0x3)
-
-#define MFP_PULL_NONE		(0x0 << 21)
-#define MFP_PULL_LOW		(0x1 << 21)
-#define MFP_PULL_HIGH		(0x2 << 21)
-#define MFP_PULL_BOTH		(0x3 << 21)
-#define MFP_PULL_MASK		(0x3 << 21)
-#define MFP_PULL(x)		(((x) >> 21) & 0x3)
-
-#define MFP_CFG_DEFAULT		(MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\
-				 MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
-
-#define MFP_CFG(pin, af)		\
-	((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af))
-
-#define MFP_CFG_DRV(pin, af, drv)	\
-	((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
-
-#define MFP_CFG_LPM(pin, af, lpm)	\
-	((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
-
-#define MFP_CFG_X(pin, af, drv, lpm)	\
-	((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
+#include <plat/mfp.h>
 
 #endif /* __ASM_ARCH_MFP_H */

arch/arm/mach-pxa/include/mach/mmc.h

@@ -14,6 +14,11 @@ struct pxamci_platform_data {
 	int (*get_ro)(struct device *);
 	void (*setpower)(struct device *, unsigned int);
 	void (*exit)(struct device *, void *);
+	int gpio_card_detect;			/* gpio detecting card insertion */
+	int gpio_card_ro;			/* gpio detecting read only toggle */
+	bool gpio_card_ro_invert;		/* gpio ro is inverted */
+	int gpio_power;				/* gpio powering up MMC bus */
+	bool gpio_power_invert;			/* gpio power is inverted */
 };
 
 extern void pxa_set_mci_info(struct pxamci_platform_data *info);

arch/arm/mach-pxa/include/mach/palmtc.h

@@ -0,0 +1,86 @@
+/*
+ * linux/include/asm-arm/arch-pxa/palmtc-gpio.h
+ *
+ * GPIOs and interrupts for Palm Tungsten|C Handheld Computer
+ *
+ * Authors:	Alex Osborne <bobofdoom@gmail.com>
+ *		Marek Vasut <marek.vasut@gmail.com>
+ *		Holger Bocklet <bitz.email@gmx.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _INCLUDE_PALMTC_H_
+#define _INCLUDE_PALMTC_H_
+
+/** HERE ARE GPIOs **/
+
+/* GPIOs */
+#define GPIO_NR_PALMTC_EARPHONE_DETECT	2
+#define GPIO_NR_PALMTC_CRADLE_DETECT	5
+#define GPIO_NR_PALMTC_HOTSYNC_BUTTON	7
+
+/* SD/MMC */
+#define GPIO_NR_PALMTC_SD_DETECT_N	12
+#define GPIO_NR_PALMTC_SD_POWER		32
+#define GPIO_NR_PALMTC_SD_READONLY	54
+
+/* WLAN */
+#define GPIO_NR_PALMTC_PCMCIA_READY	13
+#define GPIO_NR_PALMTC_PCMCIA_PWRREADY	14
+#define GPIO_NR_PALMTC_PCMCIA_POWER1	15
+#define GPIO_NR_PALMTC_PCMCIA_POWER2	33
+#define GPIO_NR_PALMTC_PCMCIA_POWER3	55
+#define GPIO_NR_PALMTC_PCMCIA_RESET	78
+
+/* UDC */
+#define GPIO_NR_PALMTC_USB_DETECT_N	4
+#define GPIO_NR_PALMTC_USB_POWER	36
+
+/* LCD/BACKLIGHT */
+#define GPIO_NR_PALMTC_BL_POWER		16
+#define GPIO_NR_PALMTC_LCD_POWER	44
+#define GPIO_NR_PALMTC_LCD_BLANK	38
+
+/* UART */
+#define GPIO_NR_PALMTC_RS232_POWER	37
+
+/* IRDA */
+#define GPIO_NR_PALMTC_IR_DISABLE	45
+
+/* IRQs */
+#define IRQ_GPIO_PALMTC_SD_DETECT_N	IRQ_GPIO(GPIO_NR_PALMTC_SD_DETECT_N)
+#define IRQ_GPIO_PALMTC_WLAN_READY	IRQ_GPIO(GPIO_NR_PALMTC_WLAN_READY)
+
+/* UCB1400 GPIOs */
+#define GPIO_NR_PALMTC_POWER_DETECT	(0x80 | 0x00)
+#define GPIO_NR_PALMTC_HEADPHONE_DETECT	(0x80 | 0x01)
+#define GPIO_NR_PALMTC_SPEAKER_ENABLE	(0x80 | 0x03)
+#define GPIO_NR_PALMTC_VIBRA_POWER	(0x80 | 0x05)
+#define GPIO_NR_PALMTC_LED_POWER	(0x80 | 0x07)
+
+/** HERE ARE INIT VALUES **/
+#define PALMTC_UCB1400_GPIO_OFFSET	0x80
+
+/* BATTERY */
+#define PALMTC_BAT_MAX_VOLTAGE		4000	/* 4.00V maximum voltage */
+#define PALMTC_BAT_MIN_VOLTAGE		3550	/* 3.55V critical voltage */
+#define PALMTC_BAT_MAX_CURRENT		0	/* unknokn */
+#define PALMTC_BAT_MIN_CURRENT		0	/* unknown */
+#define PALMTC_BAT_MAX_CHARGE		1	/* unknown */
+#define PALMTC_BAT_MIN_CHARGE		1	/* unknown */
+#define PALMTC_MAX_LIFE_MINS		240	/* on-life in minutes */
+
+#define PALMTC_BAT_MEASURE_DELAY	(HZ * 1)
+
+/* BACKLIGHT */
+#define PALMTC_MAX_INTENSITY		0xFE
+#define PALMTC_DEFAULT_INTENSITY	0x7E
+#define PALMTC_LIMIT_MASK		0x7F
+#define PALMTC_PRESCALER		0x3F
+#define PALMTC_PERIOD_NS		3500
+
+#endif

arch/arm/mach-pxa/include/mach/palmtx.h

@@ -82,6 +82,11 @@
 #define PALMTX_PHYS_FLASH_START	PXA_CS0_PHYS	/* ChipSelect 0 */
 #define PALMTX_PHYS_NAND_START	PXA_CS1_PHYS	/* ChipSelect 1 */
 
+#define PALMTX_NAND_ALE_PHYS	(PALMTX_PHYS_NAND_START | (1 << 24))
+#define PALMTX_NAND_CLE_PHYS	(PALMTX_PHYS_NAND_START | (1 << 25))
+#define PALMTX_NAND_ALE_VIRT	0xff100000
+#define PALMTX_NAND_CLE_VIRT	0xff200000
+
 /* TOUCHSCREEN */
 #define AC97_LINK_FRAME			21
 

arch/arm/mach-pxa/include/mach/pxa3xx-regs.h

@@ -208,7 +208,7 @@
 #define CKEN_MVED	43	/* < MVED clock enable */
 
 /* Note: GCU clock enable bit differs on PXA300/PXA310 and PXA320 */
-#define PXA300_CKEN_GRAPHICS	42	/* Graphics controller clock enable */
-#define PXA320_CKEN_GRAPHICS	7	/* Graphics controller clock enable */
+#define CKEN_PXA300_GCU		42	/* Graphics controller clock enable */
+#define CKEN_PXA320_GCU		7	/* Graphics controller clock enable */
 
 #endif /* __ASM_ARCH_PXA3XX_REGS_H */

arch/arm/mach-pxa/include/mach/pxafb.h

@@ -118,7 +118,8 @@ struct pxafb_mach_info {
 	u_int		fixed_modes:1,
 			cmap_inverse:1,
 			cmap_static:1,
-			unused:29;
+			acceleration_enabled:1,
+			unused:28;
 
 	/* The following should be defined in LCCR0
 	 *      LCCR0_Act or LCCR0_Pas          Active or Passive

arch/arm/mach-pxa/include/mach/regs-intc.h

@@ -13,6 +13,7 @@
 #define ICFP		__REG(0x40D0000C)  /* Interrupt Controller FIQ Pending Register */
 #define ICPR		__REG(0x40D00010)  /* Interrupt Controller Pending Register */
 #define ICCR		__REG(0x40D00014)  /* Interrupt Controller Control Register */
+#define ICHP		__REG(0x40D00018)  /* Interrupt Controller Highest Priority Register */
 
 #define ICIP2		__REG(0x40D0009C)  /* Interrupt Controller IRQ Pending Register 2 */
 #define ICMR2		__REG(0x40D000A0)  /* Interrupt Controller Mask Register 2 */
@@ -20,4 +21,14 @@
 #define ICFP2		__REG(0x40D000A8)  /* Interrupt Controller FIQ Pending Register 2 */
 #define ICPR2		__REG(0x40D000AC)  /* Interrupt Controller Pending Register 2 */
 
+#define ICIP3		__REG(0x40D00130)  /* Interrupt Controller IRQ Pending Register 3 */
+#define ICMR3		__REG(0x40D00134)  /* Interrupt Controller Mask Register 3 */
+#define ICLR3		__REG(0x40D00138)  /* Interrupt Controller Level Register 3 */
+#define ICFP3		__REG(0x40D0013C)  /* Interrupt Controller FIQ Pending Register 3 */
+#define ICPR3		__REG(0x40D00140)  /* Interrupt Controller Pending Register 3 */
+
+#define IPR(x)		__REG(0x40D0001C + (x < 32 ? (x << 2)		\
+				: (x < 64 ? (0x94 + ((x - 32) << 2))	\
+				: (0x128 + ((x - 64) << 2)))))
+
 #endif /* __ASM_MACH_REGS_INTC_H */

arch/arm/mach-pxa/include/mach/uncompress.h

@@ -37,7 +37,7 @@ static inline void arch_decomp_setup(void)
 {
 	if (machine_is_littleton() || machine_is_intelmote2()
 	    || machine_is_csb726() || machine_is_stargate2()
-	    || machine_is_cm_x300())
+	    || machine_is_cm_x300() || machine_is_balloon3())
 		UART = STUART;
 }
 

arch/arm/mach-pxa/irq.c

@@ -120,7 +120,7 @@ static void __init pxa_init_low_gpio_irq(set_wake_t fn)
 
 void __init pxa_init_irq(int irq_nr, set_wake_t fn)
 {
-	int irq;
+	int irq, i;
 
 	pxa_internal_irq_nr = irq_nr;
 
@@ -129,6 +129,12 @@ void __init pxa_init_irq(int irq_nr, set_wake_t fn)
 		_ICLR(irq) = 0;	/* all IRQs are IRQ, not FIQ */
 	}
 
+	/* initialize interrupt priority */
+	if (cpu_is_pxa27x() || cpu_is_pxa3xx()) {
+		for (i = 0; i < irq_nr; i++)
+			IPR(i) = i | (1 << 31);
+	}
+
 	/* only unmasked interrupts kick us out of idle */
 	ICCR = 1;
 

arch/arm/mach-pxa/littleton.c

@@ -265,45 +265,12 @@ static inline void littleton_init_keypad(void) {}
 #endif
 
 #if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
-static int littleton_mci_init(struct device *dev,
-			      irq_handler_t littleton_detect_int, void *data)
-{
-	int err, gpio_cd = GPIO_MMC1_CARD_DETECT;
-
-	err = gpio_request(gpio_cd, "mmc card detect");
-	if (err)
-		goto err_request_cd;
-
-	gpio_direction_input(gpio_cd);
-
-	err = request_irq(gpio_to_irq(gpio_cd), littleton_detect_int,
-			  IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-			  "mmc card detect", data);
-	if (err) {
-		dev_err(dev, "failed to request card detect IRQ\n");
-		goto err_request_irq;
-	}
-	return 0;
-
-err_request_irq:
-	gpio_free(gpio_cd);
-err_request_cd:
-	return err;
-}
-
-static void littleton_mci_exit(struct device *dev, void *data)
-{
-	int gpio_cd = GPIO_MMC1_CARD_DETECT;
-
-	free_irq(gpio_to_irq(gpio_cd), data);
-	gpio_free(gpio_cd);
-}
-
 static struct pxamci_platform_data littleton_mci_platform_data = {
-	.detect_delay	= 20,
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.init 		= littleton_mci_init,
-	.exit		= littleton_mci_exit,
+	.detect_delay		= 20,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO_MMC1_CARD_DETECT,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 static void __init littleton_init_mmc(void)

arch/arm/mach-pxa/lubbock.c

@@ -482,11 +482,14 @@ static void lubbock_mci_exit(struct device *dev, void *data)
 }
 
 static struct pxamci_platform_data lubbock_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.detect_delay	= 1,
-	.init 		= lubbock_mci_init,
-	.get_ro		= lubbock_mci_get_ro,
-	.exit 		= lubbock_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.detect_delay		= 1,
+	.init 			= lubbock_mci_init,
+	.get_ro			= lubbock_mci_get_ro,
+	.exit 			= lubbock_mci_exit,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 static void lubbock_irda_transceiver_mode(struct device *dev, int mode)
@@ -504,8 +507,9 @@ static void lubbock_irda_transceiver_mode(struct device *dev, int mode)
 }
 
 static struct pxaficp_platform_data lubbock_ficp_platform_data = {
-	.transceiver_cap  = IR_SIRMODE | IR_FIRMODE,
-	.transceiver_mode = lubbock_irda_transceiver_mode,
+	.gpio_pwdown		= -1,
+	.transceiver_cap	= IR_SIRMODE | IR_FIRMODE,
+	.transceiver_mode	= lubbock_irda_transceiver_mode,
 };
 
 static void __init lubbock_init(void)

arch/arm/mach-pxa/magician.c

@@ -140,15 +140,9 @@ static unsigned long magician_pin_config[] __initdata = {
  * IRDA
  */
 
-static void magician_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO83_MAGICIAN_nIR_EN, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
 static struct pxaficp_platform_data magician_ficp_info = {
-	.transceiver_cap  = IR_SIRMODE | IR_OFF,
-	.transceiver_mode = magician_irda_transceiver_mode,
+	.gpio_pwdown		= GPIO83_MAGICIAN_nIR_EN,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 /*
@@ -651,55 +645,24 @@ static struct platform_device bq24022 = {
 static int magician_mci_init(struct device *dev,
 				irq_handler_t detect_irq, void *data)
 {
-	int err;
-
-	err = request_irq(IRQ_MAGICIAN_SD, detect_irq,
+	return request_irq(IRQ_MAGICIAN_SD, detect_irq,
 				IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
-				"MMC card detect", data);
-	if (err)
-		goto err_request_irq;
-	err = gpio_request(EGPIO_MAGICIAN_SD_POWER, "SD_POWER");
-	if (err)
-		goto err_request_power;
-	err = gpio_request(EGPIO_MAGICIAN_nSD_READONLY, "nSD_READONLY");
-	if (err)
-		goto err_request_readonly;
-
-	return 0;
-
-err_request_readonly:
-	gpio_free(EGPIO_MAGICIAN_SD_POWER);
-err_request_power:
-	free_irq(IRQ_MAGICIAN_SD, data);
-err_request_irq:
-	return err;
-}
-
-static void magician_mci_setpower(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *pdata = dev->platform_data;
-
-	gpio_set_value(EGPIO_MAGICIAN_SD_POWER, (1 << vdd) & pdata->ocr_mask);
-}
-
-static int magician_mci_get_ro(struct device *dev)
-{
-	return (!gpio_get_value(EGPIO_MAGICIAN_nSD_READONLY));
+				"mmc card detect", data);
 }
 
 static void magician_mci_exit(struct device *dev, void *data)
 {
-	gpio_free(EGPIO_MAGICIAN_nSD_READONLY);
-	gpio_free(EGPIO_MAGICIAN_SD_POWER);
 	free_irq(IRQ_MAGICIAN_SD, data);
 }
 
 static struct pxamci_platform_data magician_mci_info = {
-	.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
-	.init     = magician_mci_init,
-	.get_ro   = magician_mci_get_ro,
-	.setpower = magician_mci_setpower,
-	.exit     = magician_mci_exit,
+	.ocr_mask 		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.init     		= magician_mci_init,
+	.exit     		= magician_mci_exit,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= EGPIO_MAGICIAN_nSD_READONLY,
+	.gpio_card_ro_invert	= 1,
+	.gpio_power		= EGPIO_MAGICIAN_SD_POWER,
 };
 
 

arch/arm/mach-pxa/mainstone.c

@@ -450,10 +450,13 @@ static void mainstone_mci_exit(struct device *dev, void *data)
 }
 
 static struct pxamci_platform_data mainstone_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init 		= mainstone_mci_init,
-	.setpower 	= mainstone_mci_setpower,
-	.exit		= mainstone_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.init 			= mainstone_mci_init,
+	.setpower 		= mainstone_mci_setpower,
+	.exit			= mainstone_mci_exit,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 static void mainstone_irda_transceiver_mode(struct device *dev, int mode)
@@ -476,8 +479,9 @@ static void mainstone_irda_transceiver_mode(struct device *dev, int mode)
 }
 
 static struct pxaficp_platform_data mainstone_ficp_platform_data = {
-	.transceiver_cap  = IR_SIRMODE | IR_FIRMODE | IR_OFF,
-	.transceiver_mode = mainstone_irda_transceiver_mode,
+	.gpio_pwdown		= -1,
+	.transceiver_cap	= IR_SIRMODE | IR_FIRMODE | IR_OFF,
+	.transceiver_mode	= mainstone_irda_transceiver_mode,
 };
 
 static struct gpio_keys_button gpio_keys_button[] = {

arch/arm/mach-pxa/mioa701.c

@@ -434,72 +434,15 @@ struct gpio_vbus_mach_info gpio_vbus_data = {
 /*
  * SDIO/MMC Card controller
  */
-static void mci_setpower(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *p_d = dev->platform_data;
-
-	if ((1 << vdd) & p_d->ocr_mask)
-		gpio_set_value(GPIO91_SDIO_EN, 1);	/* enable SDIO power */
-	else
-		gpio_set_value(GPIO91_SDIO_EN, 0);	/* disable SDIO power */
-}
-
-static int mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO78_SDIO_RO);
-}
-
-struct gpio_ress mci_gpios[] = {
-	MIO_GPIO_IN(GPIO78_SDIO_RO, 	"SDIO readonly detect"),
-	MIO_GPIO_IN(GPIO15_SDIO_INSERT,	"SDIO insertion detect"),
-	MIO_GPIO_OUT(GPIO91_SDIO_EN, 0,	"SDIO power enable")
-};
-
-static void mci_exit(struct device *dev, void *data)
-{
-	mio_gpio_free(ARRAY_AND_SIZE(mci_gpios));
-	free_irq(gpio_to_irq(GPIO15_SDIO_INSERT), data);
-}
-
-static struct pxamci_platform_data mioa701_mci_info;
-
 /**
  * The card detect interrupt isn't debounced so we delay it by 250ms
  * to give the card a chance to fully insert/eject.
  */
-static int mci_init(struct device *dev, irq_handler_t detect_int, void *data)
-{
-	int rc;
-	int irq = gpio_to_irq(GPIO15_SDIO_INSERT);
-
-	rc = mio_gpio_request(ARRAY_AND_SIZE(mci_gpios));
-	if (rc)
-		goto err_gpio;
-	/* enable RE/FE interrupt on card insertion and removal */
-	rc = request_irq(irq, detect_int,
-			 IRQF_DISABLED | IRQF_TRIGGER_RISING |
-			 IRQF_TRIGGER_FALLING,
-			 "MMC card detect", data);
-	if (rc)
-		goto err_irq;
-
-	mioa701_mci_info.detect_delay = msecs_to_jiffies(250);
-	return 0;
-
-err_irq:
-	dev_err(dev, "mioa701_mci_init: MMC/SD:"
-		" can't request MMC card detect IRQ\n");
-	mio_gpio_free(ARRAY_AND_SIZE(mci_gpios));
-err_gpio:
-	return rc;
-}
-
 static struct pxamci_platform_data mioa701_mci_info = {
-	.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
-	.init	  = mci_init,
-	.get_ro	  = mci_get_ro,
-	.setpower = mci_setpower,
-	.exit	  = mci_exit,
+	.ocr_mask 		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO15_SDIO_INSERT,
+	.gpio_card_ro		= GPIO78_SDIO_RO,
+	.gpio_power		= GPIO91_SDIO_EN,
 };
 
 /* FlashRAM */
@@ -765,19 +708,20 @@ static struct i2c_board_info __initdata mioa701_pi2c_devices[] = {
 	},
 };
 
-static struct soc_camera_link iclink = {
-	.bus_id	= 0, /* Must match id in pxa27x_device_camera in device.c */
-};
-
 /* Board I2C devices. */
 static struct i2c_board_info __initdata mioa701_i2c_devices[] = {
 	{
-		/* Must initialize before the camera(s) */
 		I2C_BOARD_INFO("mt9m111", 0x5d),
-		.platform_data = &iclink,
 	},
 };
 
+static struct soc_camera_link iclink = {
+	.bus_id		= 0, /* Match id in pxa27x_device_camera in device.c */
+	.board_info	= &mioa701_i2c_devices[0],
+	.i2c_adapter_id	= 0,
+	.module_name	= "mt9m111",
+};
+
 struct i2c_pxa_platform_data i2c_pdata = {
 	.fast_mode = 1,
 };
@@ -811,6 +755,7 @@ MIO_SIMPLE_DEV(pxa2xx_pcm,	  "pxa2xx-pcm",	    NULL)
 MIO_SIMPLE_DEV(mioa701_sound,	  "mioa701-wm9713", NULL)
 MIO_SIMPLE_DEV(mioa701_board,	  "mioa701-board",  NULL)
 MIO_SIMPLE_DEV(gpio_vbus,	  "gpio-vbus",      &gpio_vbus_data);
+MIO_SIMPLE_DEV(mioa701_camera,	  "soc-camera-pdrv",&iclink);
 
 static struct platform_device *devices[] __initdata = {
 	&mioa701_gpio_keys,
@@ -821,6 +766,7 @@ static struct platform_device *devices[] __initdata = {
 	&power_dev,
 	&strataflash,
 	&gpio_vbus,
+	&mioa701_camera,
 	&mioa701_board,
 };
 
@@ -841,7 +787,7 @@ static void mioa701_restart(char c, const char *cmd)
 static struct gpio_ress global_gpios[] = {
 	MIO_GPIO_OUT(GPIO9_CHARGE_EN, 1, "Charger enable"),
 	MIO_GPIO_OUT(GPIO18_POWEROFF, 0, "Power Off"),
-	MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power")
+	MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power"),
 };
 
 static void __init mioa701_machine_init(void)
@@ -855,6 +801,7 @@ static void __init mioa701_machine_init(void)
 	mio_gpio_request(ARRAY_AND_SIZE(global_gpios));
 	bootstrap_init();
 	set_pxa_fb_info(&mioa701_pxafb_info);
+	mioa701_mci_info.detect_delay = msecs_to_jiffies(250);
 	pxa_set_mci_info(&mioa701_mci_info);
 	pxa_set_keypad_info(&mioa701_keypad_info);
 	wm97xx_bat_set_pdata(&mioa701_battery_data);
@@ -869,7 +816,6 @@ static void __init mioa701_machine_init(void)
 	pxa_set_i2c_info(&i2c_pdata);
 	pxa27x_set_i2c_power_info(NULL);
 	pxa_set_camera_info(&mioa701_pxacamera_platform_data);
-	i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices));
 }
 
 static void mioa701_machine_exit(void)

arch/arm/mach-pxa/palmld.c

@@ -25,6 +25,9 @@
 #include <linux/wm97xx_batt.h>
 #include <linux/power_supply.h>
 #include <linux/sysdev.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -141,85 +144,50 @@ static unsigned long palmld_pin_config[] __initdata = {
 };
 
 /******************************************************************************
- * SD/MMC card controller
+ * NOR Flash
  ******************************************************************************/
-static int palmld_mci_init(struct device *dev, irq_handler_t palmld_detect_int,
-				void *data)
-{
-	int err = 0;
-
-	/* Setup an interrupt for detecting card insert/remove events */
-	err = gpio_request(GPIO_NR_PALMLD_SD_DETECT_N, "SD IRQ");
-	if (err)
-		goto err;
-	err = gpio_direction_input(GPIO_NR_PALMLD_SD_DETECT_N);
-	if (err)
-		goto err2;
-	err = request_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N),
-			palmld_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
-			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-			"SD/MMC card detect", data);
-	if (err) {
-		printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
-				__func__);
-		goto err2;
+static struct mtd_partition palmld_partitions[] = {
+	{
+		.name		= "Flash",
+		.offset		= 0x00000000,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= 0
 	}
+};
 
-	err = gpio_request(GPIO_NR_PALMLD_SD_POWER, "SD_POWER");
-	if (err)
-		goto err3;
-	err = gpio_direction_output(GPIO_NR_PALMLD_SD_POWER, 0);
-	if (err)
-		goto err4;
-
-	err = gpio_request(GPIO_NR_PALMLD_SD_READONLY, "SD_READONLY");
-	if (err)
-		goto err4;
-	err = gpio_direction_input(GPIO_NR_PALMLD_SD_READONLY);
-	if (err)
-		goto err5;
-
-	printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
-	return 0;
-
-err5:
-	gpio_free(GPIO_NR_PALMLD_SD_READONLY);
-err4:
-	gpio_free(GPIO_NR_PALMLD_SD_POWER);
-err3:
-	free_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N), data);
-err2:
-	gpio_free(GPIO_NR_PALMLD_SD_DETECT_N);
-err:
-	return err;
-}
-
-static void palmld_mci_exit(struct device *dev, void *data)
-{
-	gpio_free(GPIO_NR_PALMLD_SD_READONLY);
-	gpio_free(GPIO_NR_PALMLD_SD_POWER);
-	free_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N), data);
-	gpio_free(GPIO_NR_PALMLD_SD_DETECT_N);
-}
+static struct physmap_flash_data palmld_flash_data[] = {
+	{
+		.width		= 2,			/* bankwidth in bytes */
+		.parts		= palmld_partitions,
+		.nr_parts	= ARRAY_SIZE(palmld_partitions)
+	}
+};
 
-static void palmld_mci_power(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *p_d = dev->platform_data;
-	gpio_set_value(GPIO_NR_PALMLD_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
+static struct resource palmld_flash_resource = {
+	.start	= PXA_CS0_PHYS,
+	.end	= PXA_CS0_PHYS + SZ_4M - 1,
+	.flags	= IORESOURCE_MEM,
+};
 
-static int palmld_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_NR_PALMLD_SD_READONLY);
-}
+static struct platform_device palmld_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.resource	= &palmld_flash_resource,
+	.num_resources	= 1,
+	.dev 		= {
+		.platform_data = palmld_flash_data,
+	},
+};
 
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
 static struct pxamci_platform_data palmld_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.setpower	= palmld_mci_power,
-	.get_ro		= palmld_mci_get_ro,
-	.init 		= palmld_mci_init,
-	.exit		= palmld_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO_NR_PALMLD_SD_DETECT_N,
+	.gpio_card_ro		= GPIO_NR_PALMLD_SD_READONLY,
+	.gpio_power		= GPIO_NR_PALMLD_SD_POWER,
+	.detect_delay		= 20,
 };
 
 /******************************************************************************
@@ -336,35 +304,9 @@ static struct platform_device palmld_backlight = {
 /******************************************************************************
  * IrDA
  ******************************************************************************/
-static int palmld_irda_startup(struct device *dev)
-{
-	int err;
-	err = gpio_request(GPIO_NR_PALMLD_IR_DISABLE, "IR DISABLE");
-	if (err)
-		goto err;
-	err = gpio_direction_output(GPIO_NR_PALMLD_IR_DISABLE, 1);
-	if (err)
-		gpio_free(GPIO_NR_PALMLD_IR_DISABLE);
-err:
-	return err;
-}
-
-static void palmld_irda_shutdown(struct device *dev)
-{
-	gpio_free(GPIO_NR_PALMLD_IR_DISABLE);
-}
-
-static void palmld_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO_NR_PALMLD_IR_DISABLE, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
 static struct pxaficp_platform_data palmld_ficp_platform_data = {
-	.startup		= palmld_irda_startup,
-	.shutdown		= palmld_irda_shutdown,
-	.transceiver_cap	= IR_SIRMODE | IR_FIRMODE | IR_OFF,
-	.transceiver_mode	= palmld_irda_transceiver_mode,
+	.gpio_pwdown		= GPIO_NR_PALMLD_IR_DISABLE,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 /******************************************************************************
@@ -560,6 +502,7 @@ static struct platform_device *devices[] __initdata = {
 	&power_supply,
 	&palmld_asoc,
 	&palmld_hdd,
+	&palmld_flash,
 };
 
 static struct map_desc palmld_io_desc[] __initdata = {

arch/arm/mach-pxa/palmt5.c

@@ -124,83 +124,12 @@ static unsigned long palmt5_pin_config[] __initdata = {
 /******************************************************************************
  * SD/MMC card controller
  ******************************************************************************/
-static int palmt5_mci_init(struct device *dev, irq_handler_t palmt5_detect_int,
-				void *data)
-{
-	int err = 0;
-
-	/* Setup an interrupt for detecting card insert/remove events */
-	err = gpio_request(GPIO_NR_PALMT5_SD_DETECT_N, "SD IRQ");
-	if (err)
-		goto err;
-	err = gpio_direction_input(GPIO_NR_PALMT5_SD_DETECT_N);
-	if (err)
-		goto err2;
-	err = request_irq(gpio_to_irq(GPIO_NR_PALMT5_SD_DETECT_N),
-			palmt5_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
-			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-			"SD/MMC card detect", data);
-	if (err) {
-		printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
-				__func__);
-		goto err2;
-	}
-
-	err = gpio_request(GPIO_NR_PALMT5_SD_POWER, "SD_POWER");
-	if (err)
-		goto err3;
-	err = gpio_direction_output(GPIO_NR_PALMT5_SD_POWER, 0);
-	if (err)
-		goto err4;
-
-	err = gpio_request(GPIO_NR_PALMT5_SD_READONLY, "SD_READONLY");
-	if (err)
-		goto err4;
-	err = gpio_direction_input(GPIO_NR_PALMT5_SD_READONLY);
-	if (err)
-		goto err5;
-
-	printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
-	return 0;
-
-err5:
-	gpio_free(GPIO_NR_PALMT5_SD_READONLY);
-err4:
-	gpio_free(GPIO_NR_PALMT5_SD_POWER);
-err3:
-	free_irq(gpio_to_irq(GPIO_NR_PALMT5_SD_DETECT_N), data);
-err2:
-	gpio_free(GPIO_NR_PALMT5_SD_DETECT_N);
-err:
-	return err;
-}
-
-static void palmt5_mci_exit(struct device *dev, void *data)
-{
-	gpio_free(GPIO_NR_PALMT5_SD_READONLY);
-	gpio_free(GPIO_NR_PALMT5_SD_POWER);
-	free_irq(IRQ_GPIO_PALMT5_SD_DETECT_N, data);
-	gpio_free(GPIO_NR_PALMT5_SD_DETECT_N);
-}
-
-static void palmt5_mci_power(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *p_d = dev->platform_data;
-	gpio_set_value(GPIO_NR_PALMT5_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int palmt5_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_NR_PALMT5_SD_READONLY);
-}
-
 static struct pxamci_platform_data palmt5_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.setpower	= palmt5_mci_power,
-	.get_ro		= palmt5_mci_get_ro,
-	.init 		= palmt5_mci_init,
-	.exit		= palmt5_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO_NR_PALMT5_SD_DETECT_N,
+	.gpio_card_ro		= GPIO_NR_PALMT5_SD_READONLY,
+	.gpio_power		= GPIO_NR_PALMT5_SD_POWER,
+	.detect_delay		= 20,
 };
 
 /******************************************************************************
@@ -314,35 +243,9 @@ static struct platform_device palmt5_backlight = {
 /******************************************************************************
  * IrDA
  ******************************************************************************/
-static int palmt5_irda_startup(struct device *dev)
-{
-	int err;
-	err = gpio_request(GPIO_NR_PALMT5_IR_DISABLE, "IR DISABLE");
-	if (err)
-		goto err;
-	err = gpio_direction_output(GPIO_NR_PALMT5_IR_DISABLE, 1);
-	if (err)
-		gpio_free(GPIO_NR_PALMT5_IR_DISABLE);
-err:
-	return err;
-}
-
-static void palmt5_irda_shutdown(struct device *dev)
-{
-	gpio_free(GPIO_NR_PALMT5_IR_DISABLE);
-}
-
-static void palmt5_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO_NR_PALMT5_IR_DISABLE, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
 static struct pxaficp_platform_data palmt5_ficp_platform_data = {
-	.startup		= palmt5_irda_startup,
-	.shutdown		= palmt5_irda_shutdown,
-	.transceiver_cap	= IR_SIRMODE | IR_FIRMODE | IR_OFF,
-	.transceiver_mode	= palmt5_irda_transceiver_mode,
+	.gpio_pwdown		= GPIO_NR_PALMT5_IR_DISABLE,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 /******************************************************************************

arch/arm/mach-pxa/palmtc.c

@@ -0,0 +1,436 @@
+/*
+ * linux/arch/arm/mach-pxa/palmtc.c
+ *
+ * Support for the Palm Tungsten|C
+ *
+ * Author:	Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Based on work of:
+ *		Petr Blaha <p3t3@centrum.cz>
+ *		Chetan S. Kumar <shivakumar.chetan@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/input.h>
+#include <linux/pwm_backlight.h>
+#include <linux/gpio.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/ucb1400.h>
+#include <linux/power_supply.h>
+#include <linux/gpio_keys.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/audio.h>
+#include <mach/palmtc.h>
+#include <mach/mmc.h>
+#include <mach/pxafb.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/irda.h>
+#include <mach/udc.h>
+#include <mach/pxa2xx-regs.h>
+
+#include "generic.h"
+#include "devices.h"
+
+/******************************************************************************
+ * Pin configuration
+ ******************************************************************************/
+static unsigned long palmtc_pin_config[] __initdata = {
+	/* MMC */
+	GPIO6_MMC_CLK,
+	GPIO8_MMC_CS0,
+	GPIO12_GPIO,	/* detect */
+	GPIO32_GPIO,	/* power */
+	GPIO54_GPIO,	/* r/o switch */
+
+	/* PCMCIA */
+	GPIO52_nPCE_1,
+	GPIO53_nPCE_2,
+	GPIO50_nPIOR,
+	GPIO51_nPIOW,
+	GPIO49_nPWE,
+	GPIO48_nPOE,
+	GPIO52_nPCE_1,
+	GPIO53_nPCE_2,
+	GPIO57_nIOIS16,
+	GPIO56_nPWAIT,
+
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+
+	/* IrDA */
+	GPIO45_GPIO,	/* ir disable */
+	GPIO46_FICP_RXD,
+	GPIO47_FICP_TXD,
+
+	/* PWM */
+	GPIO17_PWM1_OUT,
+
+	/* USB */
+	GPIO4_GPIO,	/* detect */
+	GPIO36_GPIO,	/* pullup */
+
+	/* LCD */
+	GPIO58_LCD_LDD_0,
+	GPIO59_LCD_LDD_1,
+	GPIO60_LCD_LDD_2,
+	GPIO61_LCD_LDD_3,
+	GPIO62_LCD_LDD_4,
+	GPIO63_LCD_LDD_5,
+	GPIO64_LCD_LDD_6,
+	GPIO65_LCD_LDD_7,
+	GPIO66_LCD_LDD_8,
+	GPIO67_LCD_LDD_9,
+	GPIO68_LCD_LDD_10,
+	GPIO69_LCD_LDD_11,
+	GPIO70_LCD_LDD_12,
+	GPIO71_LCD_LDD_13,
+	GPIO72_LCD_LDD_14,
+	GPIO73_LCD_LDD_15,
+	GPIO74_LCD_FCLK,
+	GPIO75_LCD_LCLK,
+	GPIO76_LCD_PCLK,
+	GPIO77_LCD_BIAS,
+
+	/* MATRIX KEYPAD */
+	GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH,	/* in 0 */
+	GPIO9_GPIO | WAKEUP_ON_EDGE_BOTH,	/* in 1 */
+	GPIO10_GPIO | WAKEUP_ON_EDGE_BOTH,	/* in 2 */
+	GPIO11_GPIO | WAKEUP_ON_EDGE_BOTH,	/* in 3 */
+	GPIO18_GPIO | MFP_LPM_DRIVE_LOW,	/* out 0 */
+	GPIO19_GPIO | MFP_LPM_DRIVE_LOW,	/* out 1 */
+	GPIO20_GPIO | MFP_LPM_DRIVE_LOW,	/* out 2 */
+	GPIO21_GPIO | MFP_LPM_DRIVE_LOW,	/* out 3 */
+	GPIO22_GPIO | MFP_LPM_DRIVE_LOW,	/* out 4 */
+	GPIO23_GPIO | MFP_LPM_DRIVE_LOW,	/* out 5 */
+	GPIO24_GPIO | MFP_LPM_DRIVE_LOW,	/* out 6 */
+	GPIO25_GPIO | MFP_LPM_DRIVE_LOW,	/* out 7 */
+	GPIO26_GPIO | MFP_LPM_DRIVE_LOW,	/* out 8 */
+	GPIO27_GPIO | MFP_LPM_DRIVE_LOW,	/* out 9 */
+	GPIO79_GPIO | MFP_LPM_DRIVE_LOW,	/* out 10 */
+	GPIO80_GPIO | MFP_LPM_DRIVE_LOW,	/* out 11 */
+
+	/* PXA GPIO KEYS */
+	GPIO7_GPIO | WAKEUP_ON_EDGE_BOTH,	/* hotsync button on cradle */
+
+	/* MISC */
+	GPIO1_RST,	/* reset */
+	GPIO2_GPIO,	/* earphone detect */
+	GPIO16_GPIO,	/* backlight switch */
+};
+
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
+static struct pxamci_platform_data palmtc_mci_platform_data = {
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_power		= GPIO_NR_PALMTC_SD_POWER,
+	.gpio_card_ro		= GPIO_NR_PALMTC_SD_READONLY,
+	.gpio_card_detect	= GPIO_NR_PALMTC_SD_DETECT_N,
+	.detect_delay		= 20,
+};
+
+/******************************************************************************
+ * GPIO keys
+ ******************************************************************************/
+static struct gpio_keys_button palmtc_pxa_buttons[] = {
+	{KEY_F8, GPIO_NR_PALMTC_HOTSYNC_BUTTON, 1, "HotSync Button", EV_KEY, 1},
+};
+
+static struct gpio_keys_platform_data palmtc_pxa_keys_data = {
+	.buttons	= palmtc_pxa_buttons,
+	.nbuttons	= ARRAY_SIZE(palmtc_pxa_buttons),
+};
+
+static struct platform_device palmtc_pxa_keys = {
+	.name	= "gpio-keys",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &palmtc_pxa_keys_data,
+	},
+};
+
+/******************************************************************************
+ * Backlight
+ ******************************************************************************/
+static int palmtc_backlight_init(struct device *dev)
+{
+	int ret;
+
+	ret = gpio_request(GPIO_NR_PALMTC_BL_POWER, "BL POWER");
+	if (ret)
+		goto err;
+	ret = gpio_direction_output(GPIO_NR_PALMTC_BL_POWER, 1);
+	if (ret)
+		goto err2;
+
+	return 0;
+
+err2:
+	gpio_free(GPIO_NR_PALMTC_BL_POWER);
+err:
+	return ret;
+}
+
+static int palmtc_backlight_notify(int brightness)
+{
+	/* backlight is on when GPIO16 AF0 is high */
+	gpio_set_value(GPIO_NR_PALMTC_BL_POWER, brightness);
+	return brightness;
+}
+
+static void palmtc_backlight_exit(struct device *dev)
+{
+	gpio_free(GPIO_NR_PALMTC_BL_POWER);
+}
+
+static struct platform_pwm_backlight_data palmtc_backlight_data = {
+	.pwm_id		= 1,
+	.max_brightness	= PALMTC_MAX_INTENSITY,
+	.dft_brightness	= PALMTC_MAX_INTENSITY,
+	.pwm_period_ns	= PALMTC_PERIOD_NS,
+	.init		= palmtc_backlight_init,
+	.notify		= palmtc_backlight_notify,
+	.exit		= palmtc_backlight_exit,
+};
+
+static struct platform_device palmtc_backlight = {
+	.name	= "pwm-backlight",
+	.dev	= {
+		.parent		= &pxa25x_device_pwm1.dev,
+		.platform_data	= &palmtc_backlight_data,
+	},
+};
+
+/******************************************************************************
+ * IrDA
+ ******************************************************************************/
+static struct pxaficp_platform_data palmtc_ficp_platform_data = {
+	.gpio_pwdown		= GPIO_NR_PALMTC_IR_DISABLE,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
+};
+
+/******************************************************************************
+ * Keyboard
+ ******************************************************************************/
+static const uint32_t palmtc_matrix_keys[] = {
+	KEY(0, 0, KEY_F1),
+	KEY(0, 1, KEY_X),
+	KEY(0, 2, KEY_POWER),
+	KEY(0, 3, KEY_TAB),
+	KEY(0, 4, KEY_A),
+	KEY(0, 5, KEY_Q),
+	KEY(0, 6, KEY_LEFTSHIFT),
+	KEY(0, 7, KEY_Z),
+	KEY(0, 8, KEY_S),
+	KEY(0, 9, KEY_W),
+	KEY(0, 10, KEY_E),
+	KEY(0, 11, KEY_UP),
+
+	KEY(1, 0, KEY_F2),
+	KEY(1, 1, KEY_DOWN),
+	KEY(1, 3, KEY_D),
+	KEY(1, 4, KEY_C),
+	KEY(1, 5, KEY_F),
+	KEY(1, 6, KEY_R),
+	KEY(1, 7, KEY_SPACE),
+	KEY(1, 8, KEY_V),
+	KEY(1, 9, KEY_G),
+	KEY(1, 10, KEY_T),
+	KEY(1, 11, KEY_LEFT),
+
+	KEY(2, 0, KEY_F3),
+	KEY(2, 1, KEY_LEFTCTRL),
+	KEY(2, 3, KEY_H),
+	KEY(2, 4, KEY_Y),
+	KEY(2, 5, KEY_N),
+	KEY(2, 6, KEY_J),
+	KEY(2, 7, KEY_U),
+	KEY(2, 8, KEY_M),
+	KEY(2, 9, KEY_K),
+	KEY(2, 10, KEY_I),
+	KEY(2, 11, KEY_RIGHT),
+
+	KEY(3, 0, KEY_F4),
+	KEY(3, 1, KEY_ENTER),
+	KEY(3, 3, KEY_DOT),
+	KEY(3, 4, KEY_L),
+	KEY(3, 5, KEY_O),
+	KEY(3, 6, KEY_LEFTALT),
+	KEY(3, 7, KEY_ENTER),
+	KEY(3, 8, KEY_BACKSPACE),
+	KEY(3, 9, KEY_P),
+	KEY(3, 10, KEY_B),
+	KEY(3, 11, KEY_FN),
+};
+
+const struct matrix_keymap_data palmtc_keymap_data = {
+	.keymap			= palmtc_matrix_keys,
+	.keymap_size		= ARRAY_SIZE(palmtc_matrix_keys),
+};
+
+const static unsigned int palmtc_keypad_row_gpios[] = {
+	0, 9, 10, 11
+};
+
+const static unsigned int palmtc_keypad_col_gpios[] = {
+	18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 79, 80
+};
+
+static struct matrix_keypad_platform_data palmtc_keypad_platform_data = {
+	.keymap_data	= &palmtc_keymap_data,
+	.col_gpios	= palmtc_keypad_row_gpios,
+	.num_col_gpios	= 12,
+	.row_gpios	= palmtc_keypad_col_gpios,
+	.num_row_gpios	= 4,
+	.active_low	= 1,
+
+	.debounce_ms		= 20,
+	.col_scan_delay_us	= 5,
+};
+
+static struct platform_device palmtc_keyboard = {
+	.name	= "matrix-keypad",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &palmtc_keypad_platform_data,
+	},
+};
+
+/******************************************************************************
+ * UDC
+ ******************************************************************************/
+static struct pxa2xx_udc_mach_info palmtc_udc_info __initdata = {
+	.gpio_vbus		= GPIO_NR_PALMTC_USB_DETECT_N,
+	.gpio_vbus_inverted	= 1,
+	.gpio_pullup		= GPIO_NR_PALMTC_USB_POWER,
+};
+
+/******************************************************************************
+ * Touchscreen / Battery / GPIO-extender
+ ******************************************************************************/
+static struct platform_device palmtc_ucb1400_core = {
+	.name	= "ucb1400_core",
+	.id	= -1,
+};
+
+/******************************************************************************
+ * NOR Flash
+ ******************************************************************************/
+static struct resource palmtc_flash_resource = {
+	.start	= PXA_CS0_PHYS,
+	.end	= PXA_CS0_PHYS + SZ_16M - 1,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct mtd_partition palmtc_flash_parts[] = {
+	{
+		.name	= "U-Boot Bootloader",
+		.offset	= 0x0,
+		.size	= 0x40000,
+	},
+	{
+		.name	= "Linux Kernel",
+		.offset	= 0x40000,
+		.size	= 0x2c0000,
+	},
+	{
+		.name	= "Filesystem",
+		.offset	= 0x300000,
+		.size	= 0xcc0000,
+	},
+	{
+		.name	= "U-Boot Environment",
+		.offset	= 0xfc0000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data palmtc_flash_data = {
+	.width		= 4,
+	.parts		= palmtc_flash_parts,
+	.nr_parts	= ARRAY_SIZE(palmtc_flash_parts),
+};
+
+static struct platform_device palmtc_flash = {
+	.name		= "physmap-flash",
+	.id		= -1,
+	.resource	= &palmtc_flash_resource,
+	.num_resources	= 1,
+	.dev = {
+		.platform_data	= &palmtc_flash_data,
+	},
+};
+
+/******************************************************************************
+ * Framebuffer
+ ******************************************************************************/
+static struct pxafb_mode_info palmtc_lcd_modes[] = {
+{
+	.pixclock	= 115384,
+	.xres		= 320,
+	.yres		= 320,
+	.bpp		= 16,
+
+	.left_margin	= 27,
+	.right_margin	= 7,
+	.upper_margin	= 7,
+	.lower_margin	= 8,
+
+	.hsync_len	= 6,
+	.vsync_len	= 1,
+},
+};
+
+static struct pxafb_mach_info palmtc_lcd_screen = {
+	.modes			= palmtc_lcd_modes,
+	.num_modes		= ARRAY_SIZE(palmtc_lcd_modes),
+	.lcd_conn		= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+};
+
+/******************************************************************************
+ * Machine init
+ ******************************************************************************/
+static struct platform_device *devices[] __initdata = {
+	&palmtc_backlight,
+	&palmtc_ucb1400_core,
+	&palmtc_keyboard,
+	&palmtc_pxa_keys,
+	&palmtc_flash,
+};
+
+static void __init palmtc_init(void)
+{
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtc_pin_config));
+
+	set_pxa_fb_info(&palmtc_lcd_screen);
+	pxa_set_mci_info(&palmtc_mci_platform_data);
+	pxa_set_udc_info(&palmtc_udc_info);
+	pxa_set_ac97_info(NULL);
+	pxa_set_ficp_info(&palmtc_ficp_platform_data);
+
+	platform_add_devices(devices, ARRAY_SIZE(devices));
+};
+
+MACHINE_START(PALMTC, "Palm Tungsten|C")
+	.phys_io	= 0x40000000,
+	.boot_params 	= 0xa0000100,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa25x_init_irq,
+	.timer		= &pxa_timer,
+	.init_machine	= palmtc_init
+MACHINE_END

arch/arm/mach-pxa/palmte2.c

@@ -117,83 +117,11 @@ static unsigned long palmte2_pin_config[] __initdata = {
 /******************************************************************************
  * SD/MMC card controller
  ******************************************************************************/
-static int palmte2_mci_init(struct device *dev,
-				irq_handler_t palmte2_detect_int, void *data)
-{
-	int err = 0;
-
-	/* Setup an interrupt for detecting card insert/remove events */
-	err = gpio_request(GPIO_NR_PALMTE2_SD_DETECT_N, "SD IRQ");
-	if (err)
-		goto err;
-	err = gpio_direction_input(GPIO_NR_PALMTE2_SD_DETECT_N);
-	if (err)
-		goto err2;
-	err = request_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N),
-			palmte2_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
-			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-			"SD/MMC card detect", data);
-	if (err) {
-		printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
-				__func__);
-		goto err2;
-	}
-
-	err = gpio_request(GPIO_NR_PALMTE2_SD_POWER, "SD_POWER");
-	if (err)
-		goto err3;
-	err = gpio_direction_output(GPIO_NR_PALMTE2_SD_POWER, 0);
-	if (err)
-		goto err4;
-
-	err = gpio_request(GPIO_NR_PALMTE2_SD_READONLY, "SD_READONLY");
-	if (err)
-		goto err4;
-	err = gpio_direction_input(GPIO_NR_PALMTE2_SD_READONLY);
-	if (err)
-		goto err5;
-
-	printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
-	return 0;
-
-err5:
-	gpio_free(GPIO_NR_PALMTE2_SD_READONLY);
-err4:
-	gpio_free(GPIO_NR_PALMTE2_SD_POWER);
-err3:
-	free_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N), data);
-err2:
-	gpio_free(GPIO_NR_PALMTE2_SD_DETECT_N);
-err:
-	return err;
-}
-
-static void palmte2_mci_exit(struct device *dev, void *data)
-{
-	gpio_free(GPIO_NR_PALMTE2_SD_READONLY);
-	gpio_free(GPIO_NR_PALMTE2_SD_POWER);
-	free_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N), data);
-	gpio_free(GPIO_NR_PALMTE2_SD_DETECT_N);
-}
-
-static void palmte2_mci_power(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *p_d = dev->platform_data;
-	gpio_set_value(GPIO_NR_PALMTE2_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int palmte2_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_NR_PALMTE2_SD_READONLY);
-}
-
 static struct pxamci_platform_data palmte2_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.setpower	= palmte2_mci_power,
-	.get_ro		= palmte2_mci_get_ro,
-	.init 		= palmte2_mci_init,
-	.exit		= palmte2_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO_NR_PALMTE2_SD_DETECT_N,
+	.gpio_card_ro		= GPIO_NR_PALMTE2_SD_READONLY,
+	.gpio_power		= GPIO_NR_PALMTE2_SD_POWER,
 };
 
 /******************************************************************************
@@ -287,35 +215,9 @@ static struct platform_device palmte2_backlight = {
 /******************************************************************************
  * IrDA
  ******************************************************************************/
-static int palmte2_irda_startup(struct device *dev)
-{
-	int err;
-	err = gpio_request(GPIO_NR_PALMTE2_IR_DISABLE, "IR DISABLE");
-	if (err)
-		goto err;
-	err = gpio_direction_output(GPIO_NR_PALMTE2_IR_DISABLE, 1);
-	if (err)
-		gpio_free(GPIO_NR_PALMTE2_IR_DISABLE);
-err:
-	return err;
-}
-
-static void palmte2_irda_shutdown(struct device *dev)
-{
-	gpio_free(GPIO_NR_PALMTE2_IR_DISABLE);
-}
-
-static void palmte2_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO_NR_PALMTE2_IR_DISABLE, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
 static struct pxaficp_platform_data palmte2_ficp_platform_data = {
-	.startup		= palmte2_irda_startup,
-	.shutdown		= palmte2_irda_shutdown,
-	.transceiver_cap	= IR_SIRMODE | IR_FIRMODE | IR_OFF,
-	.transceiver_mode	= palmte2_irda_transceiver_mode,
+	.gpio_pwdown		= GPIO_NR_PALMTE2_IR_DISABLE,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 /******************************************************************************

arch/arm/mach-pxa/palmtx.c

@@ -28,6 +28,10 @@
 #include <linux/wm97xx_batt.h>
 #include <linux/power_supply.h>
 #include <linux/usb/gpio_vbus.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/physmap.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -131,6 +135,10 @@ static unsigned long palmtx_pin_config[] __initdata = {
 	GPIO34_FFUART_RXD,
 	GPIO39_FFUART_TXD,
 
+	/* NAND */
+	GPIO15_nCS_1,
+	GPIO18_RDY,
+
 	/* MISC. */
 	GPIO10_GPIO,	/* hotsync button */
 	GPIO12_GPIO,	/* power detect */
@@ -138,85 +146,50 @@ static unsigned long palmtx_pin_config[] __initdata = {
 };
 
 /******************************************************************************
- * SD/MMC card controller
+ * NOR Flash
  ******************************************************************************/
-static int palmtx_mci_init(struct device *dev, irq_handler_t palmtx_detect_int,
-				void *data)
-{
-	int err = 0;
-
-	/* Setup an interrupt for detecting card insert/remove events */
-	err = gpio_request(GPIO_NR_PALMTX_SD_DETECT_N, "SD IRQ");
-	if (err)
-		goto err;
-	err = gpio_direction_input(GPIO_NR_PALMTX_SD_DETECT_N);
-	if (err)
-		goto err2;
-	err = request_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N),
-			palmtx_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
-			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-			"SD/MMC card detect", data);
-	if (err) {
-		printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
-				__func__);
-		goto err2;
+static struct mtd_partition palmtx_partitions[] = {
+	{
+		.name		= "Flash",
+		.offset		= 0x00000000,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= 0
 	}
+};
 
-	err = gpio_request(GPIO_NR_PALMTX_SD_POWER, "SD_POWER");
-	if (err)
-		goto err3;
-	err = gpio_direction_output(GPIO_NR_PALMTX_SD_POWER, 0);
-	if (err)
-		goto err4;
-
-	err = gpio_request(GPIO_NR_PALMTX_SD_READONLY, "SD_READONLY");
-	if (err)
-		goto err4;
-	err = gpio_direction_input(GPIO_NR_PALMTX_SD_READONLY);
-	if (err)
-		goto err5;
-
-	printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
-	return 0;
-
-err5:
-	gpio_free(GPIO_NR_PALMTX_SD_READONLY);
-err4:
-	gpio_free(GPIO_NR_PALMTX_SD_POWER);
-err3:
-	free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data);
-err2:
-	gpio_free(GPIO_NR_PALMTX_SD_DETECT_N);
-err:
-	return err;
-}
-
-static void palmtx_mci_exit(struct device *dev, void *data)
-{
-	gpio_free(GPIO_NR_PALMTX_SD_READONLY);
-	gpio_free(GPIO_NR_PALMTX_SD_POWER);
-	free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data);
-	gpio_free(GPIO_NR_PALMTX_SD_DETECT_N);
-}
+static struct physmap_flash_data palmtx_flash_data[] = {
+	{
+		.width		= 2,			/* bankwidth in bytes */
+		.parts		= palmtx_partitions,
+		.nr_parts	= ARRAY_SIZE(palmtx_partitions)
+	}
+};
 
-static void palmtx_mci_power(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *p_d = dev->platform_data;
-	gpio_set_value(GPIO_NR_PALMTX_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
+static struct resource palmtx_flash_resource = {
+	.start	= PXA_CS0_PHYS,
+	.end	= PXA_CS0_PHYS + SZ_8M - 1,
+	.flags	= IORESOURCE_MEM,
+};
 
-static int palmtx_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_NR_PALMTX_SD_READONLY);
-}
+static struct platform_device palmtx_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.resource	= &palmtx_flash_resource,
+	.num_resources	= 1,
+	.dev 		= {
+		.platform_data = palmtx_flash_data,
+	},
+};
 
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
 static struct pxamci_platform_data palmtx_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.setpower	= palmtx_mci_power,
-	.get_ro		= palmtx_mci_get_ro,
-	.init 		= palmtx_mci_init,
-	.exit		= palmtx_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO_NR_PALMTX_SD_DETECT_N,
+	.gpio_card_ro		= GPIO_NR_PALMTX_SD_READONLY,
+	.gpio_power		= GPIO_NR_PALMTX_SD_POWER,
+	.detect_delay		= 20,
 };
 
 /******************************************************************************
@@ -330,35 +303,9 @@ static struct platform_device palmtx_backlight = {
 /******************************************************************************
  * IrDA
  ******************************************************************************/
-static int palmtx_irda_startup(struct device *dev)
-{
-	int err;
-	err = gpio_request(GPIO_NR_PALMTX_IR_DISABLE, "IR DISABLE");
-	if (err)
-		goto err;
-	err = gpio_direction_output(GPIO_NR_PALMTX_IR_DISABLE, 1);
-	if (err)
-		gpio_free(GPIO_NR_PALMTX_IR_DISABLE);
-err:
-	return err;
-}
-
-static void palmtx_irda_shutdown(struct device *dev)
-{
-	gpio_free(GPIO_NR_PALMTX_IR_DISABLE);
-}
-
-static void palmtx_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO_NR_PALMTX_IR_DISABLE, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
 static struct pxaficp_platform_data palmtx_ficp_platform_data = {
-	.startup		= palmtx_irda_startup,
-	.shutdown		= palmtx_irda_shutdown,
-	.transceiver_cap	= IR_SIRMODE | IR_FIRMODE | IR_OFF,
-	.transceiver_mode	= palmtx_irda_transceiver_mode,
+	.gpio_pwdown		= GPIO_NR_PALMTX_IR_DISABLE,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 /******************************************************************************
@@ -492,6 +439,68 @@ static struct pxafb_mach_info palmtx_lcd_screen = {
 	.lcd_conn	= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
 };
 
+/******************************************************************************
+ * NAND Flash
+ ******************************************************************************/
+static void palmtx_nand_cmd_ctl(struct mtd_info *mtd, int cmd,
+				 unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long nandaddr = (unsigned long)this->IO_ADDR_W;
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	if (ctrl & NAND_CLE)
+		writeb(cmd, PALMTX_NAND_CLE_VIRT);
+	else if (ctrl & NAND_ALE)
+		writeb(cmd, PALMTX_NAND_ALE_VIRT);
+	else
+		writeb(cmd, nandaddr);
+}
+
+static struct mtd_partition palmtx_partition_info[] = {
+	[0] = {
+		.name	= "palmtx-0",
+		.offset	= 0,
+		.size	= MTDPART_SIZ_FULL
+	},
+};
+
+static const char *palmtx_part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data palmtx_nand_platdata = {
+	.chip	= {
+		.nr_chips		= 1,
+		.chip_offset		= 0,
+		.nr_partitions		= ARRAY_SIZE(palmtx_partition_info),
+		.partitions		= palmtx_partition_info,
+		.chip_delay		= 20,
+		.part_probe_types 	= palmtx_part_probes,
+	},
+	.ctrl	= {
+		.cmd_ctrl	= palmtx_nand_cmd_ctl,
+	},
+};
+
+static struct resource palmtx_nand_resource[] = {
+	[0]	= {
+		.start	= PXA_CS1_PHYS,
+		.end	= PXA_CS1_PHYS + SZ_1M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device palmtx_nand = {
+	.name		= "gen_nand",
+	.num_resources	= ARRAY_SIZE(palmtx_nand_resource),
+	.resource	= palmtx_nand_resource,
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &palmtx_nand_platdata,
+	}
+};
+
 /******************************************************************************
  * Power management - standby
  ******************************************************************************/
@@ -518,6 +527,8 @@ static struct platform_device *devices[] __initdata = {
 	&power_supply,
 	&palmtx_asoc,
 	&palmtx_gpio_vbus,
+	&palmtx_flash,
+	&palmtx_nand,
 };
 
 static struct map_desc palmtx_io_desc[] __initdata = {
@@ -525,8 +536,18 @@ static struct map_desc palmtx_io_desc[] __initdata = {
 	.virtual	= PALMTX_PCMCIA_VIRT,
 	.pfn		= __phys_to_pfn(PALMTX_PCMCIA_PHYS),
 	.length		= PALMTX_PCMCIA_SIZE,
-	.type		= MT_DEVICE
-},
+	.type		= MT_DEVICE,
+}, {
+	.virtual	= PALMTX_NAND_ALE_VIRT,
+	.pfn		= __phys_to_pfn(PALMTX_NAND_ALE_PHYS),
+	.length		= SZ_1M,
+	.type		= MT_DEVICE,
+}, {
+	.virtual	= PALMTX_NAND_CLE_VIRT,
+	.pfn		= __phys_to_pfn(PALMTX_NAND_CLE_PHYS),
+	.length		= SZ_1M,
+	.type		= MT_DEVICE,
+}
 };
 
 static void __init palmtx_map_io(void)

arch/arm/mach-pxa/palmz72.c

@@ -129,88 +129,14 @@ static unsigned long palmz72_pin_config[] __initdata = {
 /******************************************************************************
  * SD/MMC card controller
  ******************************************************************************/
-static int palmz72_mci_init(struct device *dev,
-				irq_handler_t palmz72_detect_int, void *data)
-{
-	int err = 0;
-
-	/* Setup an interrupt for detecting card insert/remove events */
-	err = gpio_request(GPIO_NR_PALMZ72_SD_DETECT_N, "SD IRQ");
-	if (err)
-		goto err;
-	err = gpio_direction_input(GPIO_NR_PALMZ72_SD_DETECT_N);
-	if (err)
-		goto err2;
-	err = request_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N),
-			palmz72_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
-			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-			"SD/MMC card detect", data);
-	if (err) {
-		printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
-				__func__);
-		goto err2;
-	}
-
-	/* SD_POWER is not actually power, but it is more like chip
-	 * select, i.e. it is inverted */
-
-	err = gpio_request(GPIO_NR_PALMZ72_SD_POWER_N, "SD_POWER");
-	if (err)
-		goto err3;
-	err = gpio_direction_output(GPIO_NR_PALMZ72_SD_POWER_N, 0);
-	if (err)
-		goto err4;
-	err = gpio_request(GPIO_NR_PALMZ72_SD_RO, "SD_RO");
-	if (err)
-		goto err4;
-	err = gpio_direction_input(GPIO_NR_PALMZ72_SD_RO);
-	if (err)
-		goto err5;
-
-	printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
-	return 0;
-
-err5:
-	gpio_free(GPIO_NR_PALMZ72_SD_RO);
-err4:
-	gpio_free(GPIO_NR_PALMZ72_SD_POWER_N);
-err3:
-	free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data);
-err2:
-	gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N);
-err:
-	return err;
-}
-
-static void palmz72_mci_exit(struct device *dev, void *data)
-{
-	gpio_free(GPIO_NR_PALMZ72_SD_POWER_N);
-	free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data);
-	gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N);
-	gpio_free(GPIO_NR_PALMZ72_SD_RO);
-}
-
-static void palmz72_mci_power(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *p_d = dev->platform_data;
-	if (p_d->ocr_mask & (1 << vdd))
-		gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 0);
-	else
-		gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 1);
-}
-
-static int palmz72_mci_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_NR_PALMZ72_SD_RO);
-}
-
+/* SD_POWER is not actually power, but it is more like chip
+ * select, i.e. it is inverted */
 static struct pxamci_platform_data palmz72_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.setpower	= palmz72_mci_power,
-	.get_ro		= palmz72_mci_ro,
-	.init 		= palmz72_mci_init,
-	.exit		= palmz72_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO_NR_PALMZ72_SD_DETECT_N,
+	.gpio_card_ro		= GPIO_NR_PALMZ72_SD_RO,
+	.gpio_power		= GPIO_NR_PALMZ72_SD_POWER_N,
+	.gpio_power_invert	= 1,
 };
 
 /******************************************************************************
@@ -304,35 +230,9 @@ static struct platform_device palmz72_backlight = {
 /******************************************************************************
  * IrDA
  ******************************************************************************/
-static int palmz72_irda_startup(struct device *dev)
-{
-	int err;
-	err = gpio_request(GPIO_NR_PALMZ72_IR_DISABLE, "IR DISABLE");
-	if (err)
-		goto err;
-	err = gpio_direction_output(GPIO_NR_PALMZ72_IR_DISABLE, 1);
-	if (err)
-		gpio_free(GPIO_NR_PALMZ72_IR_DISABLE);
-err:
-	return err;
-}
-
-static void palmz72_irda_shutdown(struct device *dev)
-{
-	gpio_free(GPIO_NR_PALMZ72_IR_DISABLE);
-}
-
-static void palmz72_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO_NR_PALMZ72_IR_DISABLE, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
 static struct pxaficp_platform_data palmz72_ficp_platform_data = {
-	.startup		= palmz72_irda_startup,
-	.shutdown		= palmz72_irda_shutdown,
+	.gpio_pwdown		= GPIO_NR_PALMZ72_IR_DISABLE,
 	.transceiver_cap	= IR_SIRMODE | IR_OFF,
-	.transceiver_mode	= palmz72_irda_transceiver_mode,
 };
 
 /******************************************************************************

arch/arm/mach-pxa/pcm990-baseboard.c

@@ -321,11 +321,14 @@ static void pcm990_mci_exit(struct device *dev, void *data)
 #define MSECS_PER_JIFFY (1000/HZ)
 
 static struct pxamci_platform_data pcm990_mci_platform_data = {
-	.detect_delay	= 250 / MSECS_PER_JIFFY,
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.init 		= pcm990_mci_init,
-	.setpower 	= pcm990_mci_setpower,
-	.exit		= pcm990_mci_exit,
+	.detect_delay		= 250 / MSECS_PER_JIFFY,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.init 			= pcm990_mci_init,
+	.setpower 		= pcm990_mci_setpower,
+	.exit			= pcm990_mci_exit,
+	.gpio_card_detect	= -1,
+	.gpio_card_ro		= -1,
+	.gpio_power		= -1,
 };
 
 static struct pxaohci_platform_data pcm990_ohci_platform_data = {
@@ -427,25 +430,56 @@ static void pcm990_camera_free_bus(struct soc_camera_link *link)
 	gpio_bus_switch = -EINVAL;
 }
 
-static struct soc_camera_link iclink = {
-	.bus_id	= 0, /* Must match with the camera ID above */
-	.query_bus_param = pcm990_camera_query_bus_param,
-	.set_bus_param = pcm990_camera_set_bus_param,
-	.free_bus = pcm990_camera_free_bus,
-};
-
 /* Board I2C devices. */
 static struct i2c_board_info __initdata pcm990_i2c_devices[] = {
 	{
 		/* Must initialize before the camera(s) */
 		I2C_BOARD_INFO("pca9536", 0x41),
 		.platform_data = &pca9536_data,
-	}, {
+	},
+};
+
+static struct i2c_board_info pcm990_camera_i2c[] = {
+	{
 		I2C_BOARD_INFO("mt9v022", 0x48),
-		.platform_data = &iclink, /* With extender */
 	}, {
 		I2C_BOARD_INFO("mt9m001", 0x5d),
-		.platform_data = &iclink, /* With extender */
+	},
+};
+
+static struct soc_camera_link iclink[] = {
+	{
+		.bus_id			= 0, /* Must match with the camera ID */
+		.board_info		= &pcm990_camera_i2c[0],
+		.i2c_adapter_id		= 0,
+		.query_bus_param	= pcm990_camera_query_bus_param,
+		.set_bus_param		= pcm990_camera_set_bus_param,
+		.free_bus		= pcm990_camera_free_bus,
+		.module_name		= "mt9v022",
+	}, {
+		.bus_id			= 0, /* Must match with the camera ID */
+		.board_info		= &pcm990_camera_i2c[1],
+		.i2c_adapter_id		= 0,
+		.query_bus_param	= pcm990_camera_query_bus_param,
+		.set_bus_param		= pcm990_camera_set_bus_param,
+		.free_bus		= pcm990_camera_free_bus,
+		.module_name		= "mt9m001",
+	},
+};
+
+static struct platform_device pcm990_camera[] = {
+	{
+		.name	= "soc-camera-pdrv",
+		.id	= 0,
+		.dev	= {
+			.platform_data = &iclink[0],
+		},
+	}, {
+		.name	= "soc-camera-pdrv",
+		.id	= 1,
+		.dev	= {
+			.platform_data = &iclink[1],
+		},
 	},
 };
 #endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */
@@ -501,6 +535,9 @@ void __init pcm990_baseboard_init(void)
 	pxa_set_camera_info(&pcm990_pxacamera_platform_data);
 
 	i2c_register_board_info(0, ARRAY_AND_SIZE(pcm990_i2c_devices));
+
+	platform_device_register(&pcm990_camera[0]);
+	platform_device_register(&pcm990_camera[1]);
 #endif
 
 	printk(KERN_INFO "PCM-990 Evaluation baseboard initialized\n");

arch/arm/mach-pxa/poodle.c

@@ -245,20 +245,10 @@ static inline void poodle_init_spi(void) {}
  * The card detect interrupt isn't debounced so we delay it by 250ms
  * to give the card a chance to fully insert/eject.
  */
-static struct pxamci_platform_data poodle_mci_platform_data;
-
 static int poodle_mci_init(struct device *dev, irq_handler_t poodle_detect_int, void *data)
 {
 	int err;
 
-	err = gpio_request(POODLE_GPIO_nSD_DETECT, "nSD_DETECT");
-	if (err)
-		goto err_out;
-
-	err = gpio_request(POODLE_GPIO_nSD_WP, "nSD_WP");
-	if (err)
-		goto err_free_1;
-
 	err = gpio_request(POODLE_GPIO_SD_PWR, "SD_PWR");
 	if (err)
 		goto err_free_2;
@@ -267,34 +257,14 @@ static int poodle_mci_init(struct device *dev, irq_handler_t poodle_detect_int,
 	if (err)
 		goto err_free_3;
 
-	gpio_direction_input(POODLE_GPIO_nSD_DETECT);
-	gpio_direction_input(POODLE_GPIO_nSD_WP);
-
 	gpio_direction_output(POODLE_GPIO_SD_PWR, 0);
 	gpio_direction_output(POODLE_GPIO_SD_PWR1, 0);
 
-	poodle_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
-	err = request_irq(POODLE_IRQ_GPIO_nSD_DETECT, poodle_detect_int,
-			  IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-			  "MMC card detect", data);
-	if (err) {
-		pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
-				__func__);
-		goto err_free_4;
-	}
-
 	return 0;
 
-err_free_4:
-	gpio_free(POODLE_GPIO_SD_PWR1);
 err_free_3:
 	gpio_free(POODLE_GPIO_SD_PWR);
 err_free_2:
-	gpio_free(POODLE_GPIO_nSD_WP);
-err_free_1:
-	gpio_free(POODLE_GPIO_nSD_DETECT);
-err_out:
 	return err;
 }
 
@@ -312,62 +282,29 @@ static void poodle_mci_setpower(struct device *dev, unsigned int vdd)
 	}
 }
 
-static int poodle_mci_get_ro(struct device *dev)
-{
-	return !!gpio_get_value(POODLE_GPIO_nSD_WP);
-	return GPLR(POODLE_GPIO_nSD_WP) & GPIO_bit(POODLE_GPIO_nSD_WP);
-}
-
-
 static void poodle_mci_exit(struct device *dev, void *data)
 {
-	free_irq(POODLE_IRQ_GPIO_nSD_DETECT, data);
 	gpio_free(POODLE_GPIO_SD_PWR1);
 	gpio_free(POODLE_GPIO_SD_PWR);
-	gpio_free(POODLE_GPIO_nSD_WP);
-	gpio_free(POODLE_GPIO_nSD_DETECT);
 }
 
 static struct pxamci_platform_data poodle_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init 		= poodle_mci_init,
-	.get_ro		= poodle_mci_get_ro,
-	.setpower 	= poodle_mci_setpower,
-	.exit		= poodle_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.init 			= poodle_mci_init,
+	.setpower 		= poodle_mci_setpower,
+	.exit			= poodle_mci_exit,
+	.gpio_card_detect	= POODLE_IRQ_GPIO_nSD_DETECT,
+	.gpio_card_ro		= POODLE_GPIO_nSD_WP,
+	.gpio_power		= -1,
 };
 
 
 /*
  * Irda
  */
-static void poodle_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(POODLE_GPIO_IR_ON, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int poodle_irda_startup(struct device *dev)
-{
-	int err;
-
-	err = gpio_request(POODLE_GPIO_IR_ON, "IR_ON");
-	if (err)
-		return err;
-
-	gpio_direction_output(POODLE_GPIO_IR_ON, 1);
-	return 0;
-}
-
-static void poodle_irda_shutdown(struct device *dev)
-{
-	gpio_free(POODLE_GPIO_IR_ON);
-}
-
 static struct pxaficp_platform_data poodle_ficp_platform_data = {
+	.gpio_pwdown		= POODLE_GPIO_IR_ON,
 	.transceiver_cap	= IR_SIRMODE | IR_OFF,
-	.transceiver_mode	= poodle_irda_transceiver_mode,
-	.startup		= poodle_irda_startup,
-	.shutdown		= poodle_irda_shutdown,
 };
 
 
@@ -521,6 +458,7 @@ static void __init poodle_init(void)
 	set_pxa_fb_parent(&poodle_locomo_device.dev);
 	set_pxa_fb_info(&poodle_fb_info);
 	pxa_set_udc_info(&udc_info);
+	poodle_mci_platform_data.detect_delay = msecs_to_jiffies(250);
 	pxa_set_mci_info(&poodle_mci_platform_data);
 	pxa_set_ficp_info(&poodle_ficp_platform_data);
 	pxa_set_i2c_info(NULL);

arch/arm/mach-pxa/pxa2xx.c

@@ -52,3 +52,4 @@ void pxa2xx_transceiver_mode(struct device *dev, int mode)
 	} else
 		BUG();
 }
+EXPORT_SYMBOL_GPL(pxa2xx_transceiver_mode);

arch/arm/mach-pxa/pxa300.c

@@ -84,9 +84,11 @@ static struct mfp_addr_map pxa310_mfp_addr_map[] __initdata = {
 };
 
 static DEFINE_PXA3_CKEN(common_nand, NAND, 156000000, 0);
+static DEFINE_PXA3_CKEN(gcu, PXA300_GCU, 0, 0);
 
 static struct clk_lookup common_clkregs[] = {
 	INIT_CLKREG(&clk_common_nand, "pxa3xx-nand", NULL),
+	INIT_CLKREG(&clk_gcu, "pxa3xx-gcu", NULL),
 };
 
 static DEFINE_PXA3_CKEN(pxa310_mmc3, MMC3, 19500000, 0);

arch/arm/mach-pxa/pxa320.c

@@ -78,9 +78,11 @@ static struct mfp_addr_map pxa320_mfp_addr_map[] __initdata = {
 };
 
 static DEFINE_PXA3_CKEN(pxa320_nand, NAND, 104000000, 0);
+static DEFINE_PXA3_CKEN(gcu, PXA320_GCU, 0, 0);
 
 static struct clk_lookup pxa320_clkregs[] = {
 	INIT_CLKREG(&clk_pxa320_nand, "pxa3xx-nand", NULL),
+	INIT_CLKREG(&clk_gcu, "pxa3xx-gcu", NULL),
 };
 
 static int __init pxa320_init(void)

arch/arm/mach-pxa/pxa930.c

@@ -176,13 +176,30 @@ static struct mfp_addr_map pxa930_mfp_addr_map[] __initdata = {
 	MFP_ADDR_END,
 };
 
+static struct mfp_addr_map pxa935_mfp_addr_map[] __initdata = {
+	MFP_ADDR(GPIO159, 0x0524),
+	MFP_ADDR(GPIO163, 0x0534),
+	MFP_ADDR(GPIO167, 0x0544),
+	MFP_ADDR(GPIO168, 0x0548),
+	MFP_ADDR(GPIO169, 0x054c),
+	MFP_ADDR(GPIO170, 0x0550),
+	MFP_ADDR(GPIO171, 0x0554),
+	MFP_ADDR(GPIO172, 0x0558),
+	MFP_ADDR(GPIO173, 0x055c),
+
+	MFP_ADDR_END,
+};
+
 static int __init pxa930_init(void)
 {
-	if (cpu_is_pxa930()) {
+	if (cpu_is_pxa930() || cpu_is_pxa935()) {
 		mfp_init_base(io_p2v(MFPR_BASE));
 		mfp_init_addr(pxa930_mfp_addr_map);
 	}
 
+	if (cpu_is_pxa935())
+		mfp_init_addr(pxa935_mfp_addr_map);
+
 	return 0;
 }
 

arch/arm/mach-pxa/spitz.c

@@ -24,6 +24,7 @@
 #include <linux/spi/ads7846.h>
 #include <linux/spi/corgi_lcd.h>
 #include <linux/mtd/sharpsl.h>
+#include <linux/input/matrix_keypad.h>
 
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -111,6 +112,26 @@ static unsigned long spitz_pin_config[] __initdata = {
 	GPIO105_GPIO,	/* SPITZ_GPIO_CF_IRQ */
 	GPIO106_GPIO,	/* SPITZ_GPIO_CF2_IRQ */
 
+	/* GPIO matrix keypad */
+	GPIO88_GPIO,	/* column 0 */
+	GPIO23_GPIO,	/* column 1 */
+	GPIO24_GPIO,	/* column 2 */
+	GPIO25_GPIO,	/* column 3 */
+	GPIO26_GPIO,	/* column 4 */
+	GPIO27_GPIO,	/* column 5 */
+	GPIO52_GPIO,	/* column 6 */
+	GPIO103_GPIO,	/* column 7 */
+	GPIO107_GPIO,	/* column 8 */
+	GPIO108_GPIO,	/* column 9 */
+	GPIO114_GPIO,	/* column 10 */
+	GPIO12_GPIO,	/* row 0 */
+	GPIO17_GPIO,	/* row 1 */
+	GPIO91_GPIO,	/* row 2 */
+	GPIO34_GPIO,	/* row 3 */
+	GPIO36_GPIO,	/* row 4 */
+	GPIO38_GPIO,	/* row 5 */
+	GPIO39_GPIO,	/* row 6 */
+
 	/* I2C */
 	GPIO117_I2C_SCL,
 	GPIO118_I2C_SDA,
@@ -242,9 +263,115 @@ EXPORT_SYMBOL(spitzscoop2_device);
 /*
  * Spitz Keyboard Device
  */
+#define SPITZ_KEY_CALENDAR	KEY_F1
+#define SPITZ_KEY_ADDRESS	KEY_F2
+#define SPITZ_KEY_FN		KEY_F3
+#define SPITZ_KEY_CANCEL	KEY_F4
+#define SPITZ_KEY_EXOK		KEY_F5
+#define SPITZ_KEY_EXCANCEL	KEY_F6
+#define SPITZ_KEY_EXJOGDOWN	KEY_F7
+#define SPITZ_KEY_EXJOGUP	KEY_F8
+#define SPITZ_KEY_JAP1		KEY_LEFTALT
+#define SPITZ_KEY_JAP2		KEY_RIGHTCTRL
+#define SPITZ_KEY_SYNC		KEY_F9
+#define SPITZ_KEY_MAIL		KEY_F10
+#define SPITZ_KEY_OK		KEY_F11
+#define SPITZ_KEY_MENU		KEY_F12
+
+static const uint32_t spitzkbd_keymap[] = {
+	KEY(0, 0, KEY_LEFTCTRL),
+	KEY(0, 1, KEY_1),
+	KEY(0, 2, KEY_3),
+	KEY(0, 3, KEY_5),
+	KEY(0, 4, KEY_6),
+	KEY(0, 5, KEY_7),
+	KEY(0, 6, KEY_9),
+	KEY(0, 7, KEY_0),
+	KEY(0, 8, KEY_BACKSPACE),
+	KEY(0, 9, SPITZ_KEY_EXOK),	/* EXOK */
+	KEY(0, 10, SPITZ_KEY_EXCANCEL),	/* EXCANCEL */
+	KEY(1, 1, KEY_2),
+	KEY(1, 2, KEY_4),
+	KEY(1, 3, KEY_R),
+	KEY(1, 4, KEY_Y),
+	KEY(1, 5, KEY_8),
+	KEY(1, 6, KEY_I),
+	KEY(1, 7, KEY_O),
+	KEY(1, 8, KEY_P),
+	KEY(1, 9, SPITZ_KEY_EXJOGDOWN),	/* EXJOGDOWN */
+	KEY(1, 10, SPITZ_KEY_EXJOGUP),	/* EXJOGUP */
+	KEY(2, 0, KEY_TAB),
+	KEY(2, 1, KEY_Q),
+	KEY(2, 2, KEY_E),
+	KEY(2, 3, KEY_T),
+	KEY(2, 4, KEY_G),
+	KEY(2, 5, KEY_U),
+	KEY(2, 6, KEY_J),
+	KEY(2, 7, KEY_K),
+	KEY(3, 0, SPITZ_KEY_ADDRESS),	/* ADDRESS */
+	KEY(3, 1, KEY_W),
+	KEY(3, 2, KEY_S),
+	KEY(3, 3, KEY_F),
+	KEY(3, 4, KEY_V),
+	KEY(3, 5, KEY_H),
+	KEY(3, 6, KEY_M),
+	KEY(3, 7, KEY_L),
+	KEY(3, 9, KEY_RIGHTSHIFT),
+	KEY(4, 0, SPITZ_KEY_CALENDAR),	/* CALENDAR */
+	KEY(4, 1, KEY_A),
+	KEY(4, 2, KEY_D),
+	KEY(4, 3, KEY_C),
+	KEY(4, 4, KEY_B),
+	KEY(4, 5, KEY_N),
+	KEY(4, 6, KEY_DOT),
+	KEY(4, 8, KEY_ENTER),
+	KEY(4, 9, KEY_LEFTSHIFT),
+	KEY(5, 0, SPITZ_KEY_MAIL),	/* MAIL */
+	KEY(5, 1, KEY_Z),
+	KEY(5, 2, KEY_X),
+	KEY(5, 3, KEY_MINUS),
+	KEY(5, 4, KEY_SPACE),
+	KEY(5, 5, KEY_COMMA),
+	KEY(5, 7, KEY_UP),
+	KEY(5, 10, SPITZ_KEY_FN),	/* FN */
+	KEY(6, 0, KEY_SYSRQ),
+	KEY(6, 1, SPITZ_KEY_JAP1),	/* JAP1 */
+	KEY(6, 2, SPITZ_KEY_JAP2),	/* JAP2 */
+	KEY(6, 3, SPITZ_KEY_CANCEL),	/* CANCEL */
+	KEY(6, 4, SPITZ_KEY_OK),	/* OK */
+	KEY(6, 5, SPITZ_KEY_MENU),	/* MENU */
+	KEY(6, 6, KEY_LEFT),
+	KEY(6, 7, KEY_DOWN),
+	KEY(6, 8, KEY_RIGHT),
+};
+
+static const struct matrix_keymap_data spitzkbd_keymap_data = {
+	.keymap		= spitzkbd_keymap,
+	.keymap_size	= ARRAY_SIZE(spitzkbd_keymap),
+};
+
+static const uint32_t spitzkbd_row_gpios[] =
+		{ 12, 17, 91, 34, 36, 38, 39 };
+static const uint32_t spitzkbd_col_gpios[] =
+		{ 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 };
+
+static struct matrix_keypad_platform_data spitzkbd_pdata = {
+	.keymap_data		= &spitzkbd_keymap_data,
+	.row_gpios		= spitzkbd_row_gpios,
+	.col_gpios		= spitzkbd_col_gpios,
+	.num_row_gpios		= ARRAY_SIZE(spitzkbd_row_gpios),
+	.num_col_gpios		= ARRAY_SIZE(spitzkbd_col_gpios),
+	.col_scan_delay_us	= 10,
+	.debounce_ms		= 10,
+	.wakeup			= 1,
+};
+
 static struct platform_device spitzkbd_device = {
-	.name		= "spitz-keyboard",
+	.name		= "matrix-keypad",
 	.id		= -1,
+	.dev		= {
+		.platform_data = &spitzkbd_pdata,
+	},
 };
 
 
@@ -296,6 +423,7 @@ static struct ads7846_platform_data spitz_ads7846_info = {
 	.vref_delay_usecs	= 100,
 	.x_plate_ohms		= 419,
 	.y_plate_ohms		= 486,
+	.pressure_max		= 1024,
 	.gpio_pendown		= SPITZ_GPIO_TP_INT,
 	.wait_for_sync		= spitz_wait_for_hsync,
 };
@@ -378,45 +506,6 @@ static inline void spitz_init_spi(void) {}
  * The card detect interrupt isn't debounced so we delay it by 250ms
  * to give the card a chance to fully insert/eject.
  */
-
-static struct pxamci_platform_data spitz_mci_platform_data;
-
-static int spitz_mci_init(struct device *dev, irq_handler_t spitz_detect_int, void *data)
-{
-	int err;
-
-	err = gpio_request(SPITZ_GPIO_nSD_DETECT, "nSD_DETECT");
-	if (err)
-		goto err_out;
-
-	err = gpio_request(SPITZ_GPIO_nSD_WP, "nSD_WP");
-	if (err)
-		goto err_free_1;
-
-	gpio_direction_input(SPITZ_GPIO_nSD_DETECT);
-	gpio_direction_input(SPITZ_GPIO_nSD_WP);
-
-	spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
-	err = request_irq(SPITZ_IRQ_GPIO_nSD_DETECT, spitz_detect_int,
-			  IRQF_DISABLED | IRQF_TRIGGER_RISING |
-			  IRQF_TRIGGER_FALLING,
-			  "MMC card detect", data);
-	if (err) {
-		pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
-				__func__);
-		goto err_free_2;
-	}
-	return 0;
-
-err_free_2:
-	gpio_free(SPITZ_GPIO_nSD_WP);
-err_free_1:
-	gpio_free(SPITZ_GPIO_nSD_DETECT);
-err_out:
-	return err;
-}
-
 static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
 {
 	struct pxamci_platform_data* p_d = dev->platform_data;
@@ -427,24 +516,12 @@ static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
 		spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0000);
 }
 
-static int spitz_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(SPITZ_GPIO_nSD_WP);
-}
-
-static void spitz_mci_exit(struct device *dev, void *data)
-{
-	free_irq(SPITZ_IRQ_GPIO_nSD_DETECT, data);
-	gpio_free(SPITZ_GPIO_nSD_WP);
-	gpio_free(SPITZ_GPIO_nSD_DETECT);
-}
-
 static struct pxamci_platform_data spitz_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
-	.init 		= spitz_mci_init,
-	.get_ro		= spitz_mci_get_ro,
-	.setpower 	= spitz_mci_setpower,
-	.exit		= spitz_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33|MMC_VDD_33_34,
+	.setpower 		= spitz_mci_setpower,
+	.gpio_card_detect	= SPITZ_GPIO_nSD_DETECT,
+	.gpio_card_ro		= SPITZ_GPIO_nSD_WP,
+	.gpio_power		= -1,
 };
 
 
@@ -484,50 +561,10 @@ static struct pxaohci_platform_data spitz_ohci_platform_data = {
 /*
  * Irda
  */
-static int spitz_irda_startup(struct device *dev)
-{
-	int rc;
-
-	rc = gpio_request(SPITZ_GPIO_IR_ON, "IrDA on");
-	if (rc)
-		goto err;
-
-	rc = gpio_direction_output(SPITZ_GPIO_IR_ON, 1);
-	if (rc)
-		goto err_dir;
-
-	return 0;
-
-err_dir:
-	gpio_free(SPITZ_GPIO_IR_ON);
-err:
-	return rc;
-}
-
-static void spitz_irda_shutdown(struct device *dev)
-{
-	gpio_free(SPITZ_GPIO_IR_ON);
-}
-
-static void spitz_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(SPITZ_GPIO_IR_ON, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
-#ifdef CONFIG_MACH_AKITA
-static void akita_irda_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(AKITA_GPIO_IR_ON, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-#endif
 
 static struct pxaficp_platform_data spitz_ficp_platform_data = {
+/* .gpio_pwdown is set in spitz_init() and akita_init() accordingly */
 	.transceiver_cap	= IR_SIRMODE | IR_OFF,
-	.transceiver_mode	= spitz_irda_transceiver_mode,
-	.startup		= spitz_irda_startup,
-	.shutdown		= spitz_irda_shutdown,
 };
 
 
@@ -695,6 +732,7 @@ static void __init common_init(void)
 	spitz_init_spi();
 
 	platform_add_devices(devices, ARRAY_SIZE(devices));
+	spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250);
 	pxa_set_mci_info(&spitz_mci_platform_data);
 	pxa_set_ohci_info(&spitz_ohci_platform_data);
 	pxa_set_ficp_info(&spitz_ficp_platform_data);
@@ -705,6 +743,8 @@ static void __init common_init(void)
 #if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI)
 static void __init spitz_init(void)
 {
+	spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
+
 	platform_scoop_config = &spitz_pcmcia_config;
 
 	common_init();
@@ -747,7 +787,7 @@ static struct nand_ecclayout akita_oobinfo = {
 
 static void __init akita_init(void)
 {
-	spitz_ficp_platform_data.transceiver_mode = akita_irda_transceiver_mode;
+	spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
 
 	sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt;
 	sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo;

arch/arm/mach-pxa/tosa.c

@@ -247,49 +247,10 @@ static struct pxa2xx_udc_mach_info udc_info __initdata = {
 /*
  * MMC/SD Device
  */
-static struct pxamci_platform_data tosa_mci_platform_data;
-
 static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void *data)
 {
 	int err;
 
-	tosa_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
-	err = gpio_request(TOSA_GPIO_nSD_DETECT, "MMC/SD card detect");
-	if (err) {
-		printk(KERN_ERR "tosa_mci_init: can't request nSD_DETECT gpio\n");
-		goto err_gpio_detect;
-	}
-	err = gpio_direction_input(TOSA_GPIO_nSD_DETECT);
-	if (err)
-		goto err_gpio_detect_dir;
-
-	err = request_irq(TOSA_IRQ_GPIO_nSD_DETECT, tosa_detect_int,
-			  IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
-				"MMC/SD card detect", data);
-	if (err) {
-		printk(KERN_ERR "tosa_mci_init: MMC/SD: can't request MMC card detect IRQ\n");
-		goto err_irq;
-	}
-
-	err = gpio_request(TOSA_GPIO_SD_WP, "SD Write Protect");
-	if (err) {
-		printk(KERN_ERR "tosa_mci_init: can't request SD_WP gpio\n");
-		goto err_gpio_wp;
-	}
-	err = gpio_direction_input(TOSA_GPIO_SD_WP);
-	if (err)
-		goto err_gpio_wp_dir;
-
-	err = gpio_request(TOSA_GPIO_PWR_ON, "SD Power");
-	if (err) {
-		printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n");
-		goto err_gpio_pwr;
-	}
-	err = gpio_direction_output(TOSA_GPIO_PWR_ON, 0);
-	if (err)
-		goto err_gpio_pwr_dir;
-
 	err = gpio_request(TOSA_GPIO_nSD_INT, "SD Int");
 	if (err) {
 		printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n");
@@ -304,51 +265,21 @@ static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void
 err_gpio_int_dir:
 	gpio_free(TOSA_GPIO_nSD_INT);
 err_gpio_int:
-err_gpio_pwr_dir:
-	gpio_free(TOSA_GPIO_PWR_ON);
-err_gpio_pwr:
-err_gpio_wp_dir:
-	gpio_free(TOSA_GPIO_SD_WP);
-err_gpio_wp:
-	free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data);
-err_irq:
-err_gpio_detect_dir:
-	gpio_free(TOSA_GPIO_nSD_DETECT);
-err_gpio_detect:
 	return err;
 }
 
-static void tosa_mci_setpower(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data* p_d = dev->platform_data;
-
-	if (( 1 << vdd) & p_d->ocr_mask) {
-		gpio_set_value(TOSA_GPIO_PWR_ON, 1);
-	} else {
-		gpio_set_value(TOSA_GPIO_PWR_ON, 0);
-	}
-}
-
-static int tosa_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(TOSA_GPIO_SD_WP);
-}
-
 static void tosa_mci_exit(struct device *dev, void *data)
 {
 	gpio_free(TOSA_GPIO_nSD_INT);
-	gpio_free(TOSA_GPIO_PWR_ON);
-	gpio_free(TOSA_GPIO_SD_WP);
-	free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data);
-	gpio_free(TOSA_GPIO_nSD_DETECT);
 }
 
 static struct pxamci_platform_data tosa_mci_platform_data = {
-	.ocr_mask       = MMC_VDD_32_33|MMC_VDD_33_34,
-	.init           = tosa_mci_init,
-	.get_ro		= tosa_mci_get_ro,
-	.setpower       = tosa_mci_setpower,
-	.exit           = tosa_mci_exit,
+	.ocr_mask       	= MMC_VDD_32_33|MMC_VDD_33_34,
+	.init           	= tosa_mci_init,
+	.exit           	= tosa_mci_exit,
+	.gpio_card_detect	= TOSA_GPIO_nSD_DETECT,
+	.gpio_card_ro		= TOSA_GPIO_SD_WP,
+	.gpio_power		= TOSA_GPIO_PWR_ON,
 };
 
 /*
@@ -406,10 +337,11 @@ static void tosa_irda_shutdown(struct device *dev)
 }
 
 static struct pxaficp_platform_data tosa_ficp_platform_data = {
-	.transceiver_cap  = IR_SIRMODE | IR_OFF,
-	.transceiver_mode = tosa_irda_transceiver_mode,
-	.startup = tosa_irda_startup,
-	.shutdown = tosa_irda_shutdown,
+	.gpio_pwdown		= -1,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
+	.transceiver_mode	= tosa_irda_transceiver_mode,
+	.startup		= tosa_irda_startup,
+	.shutdown		= tosa_irda_shutdown,
 };
 
 /*
@@ -910,6 +842,7 @@ static void __init tosa_init(void)
 	dummy = gpiochip_reserve(TOSA_SCOOP_JC_GPIO_BASE, 12);
 	dummy = gpiochip_reserve(TOSA_TC6393XB_GPIO_BASE, 16);
 
+	tosa_mci_platform_data.detect_delay = msecs_to_jiffies(250);
 	pxa_set_mci_info(&tosa_mci_platform_data);
 	pxa_set_udc_info(&udc_info);
 	pxa_set_ficp_info(&tosa_ficp_platform_data);

arch/arm/mach-pxa/treo680.c

@@ -153,87 +153,11 @@ static unsigned long treo680_pin_config[] __initdata = {
 /******************************************************************************
  * SD/MMC card controller
  ******************************************************************************/
-static int treo680_mci_init(struct device *dev,
-		irq_handler_t treo680_detect_int, void *data)
-{
-	int err = 0;
-
-	/* Setup an interrupt for detecting card insert/remove events */
-	err = gpio_request(GPIO_NR_TREO680_SD_DETECT_N, "SD IRQ");
-
-	if (err)
-		goto err;
-
-	err = gpio_direction_input(GPIO_NR_TREO680_SD_DETECT_N);
-	if (err)
-		goto err2;
-
-	err = request_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N),
-			treo680_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
-			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
-			"SD/MMC card detect", data);
-
-	if (err) {
-		dev_err(dev, "%s: cannot request SD/MMC card detect IRQ\n",
-			     __func__);
-		goto err2;
-	}
-
-	err = gpio_request(GPIO_NR_TREO680_SD_POWER, "SD_POWER");
-	if (err)
-		goto err3;
-
-	err = gpio_direction_output(GPIO_NR_TREO680_SD_POWER, 1);
-	if (err)
-		goto err4;
-
-	err = gpio_request(GPIO_NR_TREO680_SD_READONLY, "SD_READONLY");
-	if (err)
-		goto err4;
-
-	err = gpio_direction_input(GPIO_NR_TREO680_SD_READONLY);
-	if (err)
-		goto err5;
-
-	return 0;
-
-err5:
-	gpio_free(GPIO_NR_TREO680_SD_READONLY);
-err4:
-	gpio_free(GPIO_NR_TREO680_SD_POWER);
-err3:
-	free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
-err2:
-	gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
-err:
-	return err;
-}
-
-static void treo680_mci_exit(struct device *dev, void *data)
-{
-	gpio_free(GPIO_NR_TREO680_SD_READONLY);
-	gpio_free(GPIO_NR_TREO680_SD_POWER);
-	free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
-	gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
-}
-
-static void treo680_mci_power(struct device *dev, unsigned int vdd)
-{
-	struct pxamci_platform_data *p_d = dev->platform_data;
-	gpio_set_value(GPIO_NR_TREO680_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int treo680_mci_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_NR_TREO680_SD_READONLY);
-}
-
 static struct pxamci_platform_data treo680_mci_platform_data = {
-	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
-	.setpower	= treo680_mci_power,
-	.get_ro		= treo680_mci_get_ro,
-	.init 		= treo680_mci_init,
-	.exit		= treo680_mci_exit,
+	.ocr_mask		= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.gpio_card_detect	= GPIO_NR_TREO680_SD_DETECT_N,
+	.gpio_card_ro		= GPIO_NR_TREO680_SD_READONLY,
+	.gpio_power		= GPIO_NR_TREO680_SD_POWER,
 };
 
 /******************************************************************************
@@ -330,16 +254,9 @@ static int treo680_backlight_init(struct device *dev)
 	ret = gpio_direction_output(GPIO_NR_TREO680_BL_POWER, 0);
 	if (ret)
 		goto err2;
-	ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
-	if (ret)
-		goto err2;
-	ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
-	if (ret)
-		goto err3;
 
 	return 0;
-err3:
-	gpio_free(GPIO_NR_TREO680_LCD_POWER);
+
 err2:
 	gpio_free(GPIO_NR_TREO680_BL_POWER);
 err:
@@ -355,7 +272,6 @@ static int treo680_backlight_notify(int brightness)
 static void treo680_backlight_exit(struct device *dev)
 {
 	gpio_free(GPIO_NR_TREO680_BL_POWER);
-	gpio_free(GPIO_NR_TREO680_LCD_POWER);
 }
 
 static struct platform_pwm_backlight_data treo680_backlight_data = {
@@ -379,44 +295,9 @@ static struct platform_device treo680_backlight = {
 /******************************************************************************
  * IrDA
  ******************************************************************************/
-static void treo680_transceiver_mode(struct device *dev, int mode)
-{
-	gpio_set_value(GPIO_NR_TREO680_IR_EN, mode & IR_OFF);
-	pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int treo680_irda_startup(struct device *dev)
-{
-	int err;
-
-	err = gpio_request(GPIO_NR_TREO680_IR_EN, "Ir port disable");
-	if (err)
-		goto err1;
-
-	err = gpio_direction_output(GPIO_NR_TREO680_IR_EN, 1);
-	if (err)
-		goto err2;
-
-	return 0;
-
-err2:
-	dev_err(dev, "treo680_irda: cannot change IR gpio direction\n");
-	gpio_free(GPIO_NR_TREO680_IR_EN);
-err1:
-	dev_err(dev, "treo680_irda: cannot allocate IR gpio\n");
-	return err;
-}
-
-static void treo680_irda_shutdown(struct device *dev)
-{
-	gpio_free(GPIO_NR_TREO680_IR_EN);
-}
-
 static struct pxaficp_platform_data treo680_ficp_info = {
-	.transceiver_cap  = IR_FIRMODE | IR_SIRMODE | IR_OFF,
-	.startup          = treo680_irda_startup,
-	.shutdown         = treo680_irda_shutdown,
-	.transceiver_mode = treo680_transceiver_mode,
+	.gpio_pwdown		= GPIO_NR_TREO680_IR_EN,
+	.transceiver_cap	= IR_SIRMODE | IR_OFF,
 };
 
 /******************************************************************************
@@ -546,6 +427,11 @@ static struct pxafb_mode_info treo680_lcd_modes[] = {
 },
 };
 
+static void treo680_lcd_power(int on, struct fb_var_screeninfo *info)
+{
+	gpio_set_value(GPIO_NR_TREO680_BL_POWER, on);
+}
+
 static struct pxafb_mach_info treo680_lcd_screen = {
 	.modes		= treo680_lcd_modes,
 	.num_modes	= ARRAY_SIZE(treo680_lcd_modes),
@@ -585,11 +471,32 @@ static void __init treo680_udc_init(void)
 	}
 }
 
+static void __init treo680_lcd_power_init(void)
+{
+	int ret;
+
+	ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
+	if (ret) {
+		pr_err("Treo680: LCD power GPIO request failed!\n");
+		return;
+	}
+
+	ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
+	if (ret) {
+		pr_err("Treo680: setting LCD power GPIO direction failed!\n");
+		gpio_free(GPIO_NR_TREO680_LCD_POWER);
+		return;
+	}
+
+	treo680_lcd_screen.pxafb_lcd_power = treo680_lcd_power;
+}
+
 static void __init treo680_init(void)
 {
 	treo680_pm_init();
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
 	pxa_set_keypad_info(&treo680_keypad_platform_data);
+	treo680_lcd_power_init();
 	set_pxa_fb_info(&treo680_lcd_screen);
 	pxa_set_mci_info(&treo680_mci_platform_data);
 	treo680_udc_init();

arch/arm/mach-pxa/trizeps4.c

@@ -367,6 +367,9 @@ static struct pxamci_platform_data trizeps4_mci_platform_data = {
 	.exit		= trizeps4_mci_exit,
 	.get_ro		= NULL,	/* write-protection not supported */
 	.setpower 	= NULL,	/* power-switching not supported */
+	.gpio_card_detect = -1,
+	.gpio_card_ro	= -1,
+	.gpio_power	= -1,
 };
 
 /****************************************************************************
@@ -412,6 +415,7 @@ static void trizeps4_irda_transceiver_mode(struct device *dev, int mode)
 }
 
 static struct pxaficp_platform_data trizeps4_ficp_platform_data = {
+	.gpio_pwdown		= -1,
 	.transceiver_cap	= IR_SIRMODE | IR_FIRMODE | IR_OFF,
 	.transceiver_mode	= trizeps4_irda_transceiver_mode,
 	.startup		= trizeps4_irda_startup,

arch/arm/mach-pxa/xcep.c

@@ -0,0 +1,187 @@
+/*  linux/arch/arm/mach-pxa/xcep.c
+ *
+ *  Support for the Iskratel Electronics XCEP platform as used in
+ *  the Libera instruments from Instrumentation Technologies.
+ *
+ *  Author:     Ales Bardorfer <ales@i-tech.si>
+ *  Contributions by: Abbott, MG (Michael) <michael.abbott@diamond.ac.uk>
+ *  Contributions by: Matej Kenda <matej.kenda@i-tech.si>
+ *  Created:    June 2006
+ *  Copyright:  (C) 2006-2009 Instrumentation Technologies
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/smc91x.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/map.h>
+
+#include <plat/i2c.h>
+
+#include <mach/hardware.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa25x.h>
+
+#include "generic.h"
+
+#define XCEP_ETH_PHYS		(PXA_CS3_PHYS + 0x00000300)
+#define XCEP_ETH_PHYS_END	(PXA_CS3_PHYS + 0x000fffff)
+#define XCEP_ETH_ATTR		(PXA_CS3_PHYS + 0x02000000)
+#define XCEP_ETH_ATTR_END	(PXA_CS3_PHYS + 0x020fffff)
+#define XCEP_ETH_IRQ		IRQ_GPIO0
+
+/*  XCEP CPLD base */
+#define XCEP_CPLD_BASE		0xf0000000
+
+
+/* Flash partitions. */
+
+static struct mtd_partition xcep_partitions[] = {
+	{
+		.name =		"Bootloader",
+		.size =		0x00040000,
+		.offset =	0,
+		.mask_flags =	MTD_WRITEABLE
+	}, {
+		.name =		"Bootloader ENV",
+		.size =		0x00040000,
+		.offset =	0x00040000,
+		.mask_flags =	MTD_WRITEABLE
+	}, {
+		.name =		"Kernel",
+		.size =		0x00100000,
+		.offset =	0x00080000,
+	}, {
+		.name =		"Rescue fs",
+		.size =		0x00280000,
+		.offset =	0x00180000,
+	}, {
+		.name =		"Filesystem",
+		.size =		MTDPART_SIZ_FULL,
+		.offset =	0x00400000
+	}
+};
+
+static struct physmap_flash_data xcep_flash_data[] = {
+	{
+		.width		= 4,		/* bankwidth in bytes */
+		.parts		= xcep_partitions,
+		.nr_parts	= ARRAY_SIZE(xcep_partitions)
+	}
+};
+
+static struct resource flash_resource = {
+	.start	= PXA_CS0_PHYS,
+	.end	= PXA_CS0_PHYS + SZ_32M - 1,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct platform_device flash_device = {
+	.name	= "physmap-flash",
+	.id	= 0,
+	.dev 	= {
+		.platform_data = xcep_flash_data,
+	},
+	.resource = &flash_resource,
+	.num_resources = 1,
+};
+
+
+
+/* SMC LAN91C111 network controller. */
+
+static struct resource smc91x_resources[] = {
+	[0] = {
+		.name	= "smc91x-regs",
+		.start	= XCEP_ETH_PHYS,
+		.end	= XCEP_ETH_PHYS_END,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= XCEP_ETH_IRQ,
+		.end	= XCEP_ETH_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.name	= "smc91x-attrib",
+		.start	= XCEP_ETH_ATTR,
+		.end	= XCEP_ETH_ATTR_END,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct smc91x_platdata xcep_smc91x_info = {
+	.flags	= SMC91X_USE_32BIT | SMC91X_NOWAIT | SMC91X_USE_DMA,
+};
+
+static struct platform_device smc91x_device = {
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(smc91x_resources),
+	.resource	= smc91x_resources,
+	.dev		= {
+		.platform_data = &xcep_smc91x_info,
+	},
+};
+
+
+static struct platform_device *devices[] __initdata = {
+	&flash_device,
+	&smc91x_device,
+};
+
+
+/* We have to state that there are HWMON devices on the I2C bus on XCEP.
+ * Drivers for HWMON verify capabilities of the adapter when loading and
+ * refuse to attach if the adapter doesn't support HWMON class of devices.
+ * See also Documentation/i2c/porting-clients. */
+static struct i2c_pxa_platform_data xcep_i2c_platform_data  = {
+	.class = I2C_CLASS_HWMON
+};
+
+
+static mfp_cfg_t xcep_pin_config[] __initdata = {
+	GPIO79_nCS_3,	/* SMC 91C111 chip select. */
+	GPIO80_nCS_4,	/* CPLD chip select. */
+	/* SSP communication to MSP430 */
+	GPIO23_SSP1_SCLK,
+	GPIO24_SSP1_SFRM,
+	GPIO25_SSP1_TXD,
+	GPIO26_SSP1_RXD,
+	GPIO27_SSP1_EXTCLK
+};
+
+static void __init xcep_init(void)
+{
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(xcep_pin_config));
+
+	/* See Intel XScale Developer's Guide for details */
+	/* Set RDF and RDN to appropriate values (chip select 3 (smc91x)) */
+	MSC1 = (MSC1 & 0xffff) | 0xD5540000;
+	/* Set RDF and RDN to appropriate values (chip select 5 (fpga)) */
+	MSC2 = (MSC2 & 0xffff) | 0x72A00000;
+
+	platform_add_devices(ARRAY_AND_SIZE(devices));
+	pxa_set_i2c_info(&xcep_i2c_platform_data);
+}
+
+MACHINE_START(XCEP, "Iskratel XCEP")
+	.phys_io	= 0x40000000,
+	.io_pg_offst	= (io_p2v(0x40000000) >> 18) & 0xfffc,
+	.boot_params	= 0xa0000100,
+	.init_machine	= xcep_init,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa25x_init_irq,
+	.timer		= &pxa_timer,
+MACHINE_END
+

arch/arm/mach-pxa/zylonite.c

@@ -290,6 +290,9 @@ static struct pxamci_platform_data zylonite_mci_platform_data = {
 	.init 		= zylonite_mci_init,
 	.exit		= zylonite_mci_exit,
 	.get_ro		= zylonite_mci_ro,
+	.gpio_card_detect = -1,
+	.gpio_card_ro	= -1,
+	.gpio_power	= -1,
 };
 
 static struct pxamci_platform_data zylonite_mci2_platform_data = {

arch/arm/mach-realview/core.c

@@ -30,6 +30,7 @@
 #include <linux/io.h>
 #include <linux/smsc911x.h>
 #include <linux/ata_platform.h>
+#include <linux/amba/mmci.h>
 
 #include <asm/clkdev.h>
 #include <asm/system.h>
@@ -44,7 +45,6 @@
 #include <asm/mach/flash.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 
 #include <asm/hardware/gic.h>
 
@@ -237,14 +237,14 @@ static unsigned int realview_mmc_status(struct device *dev)
 	return readl(REALVIEW_SYSMCI) & mask;
 }
 
-struct mmc_platform_data realview_mmc0_plat_data = {
+struct mmci_platform_data realview_mmc0_plat_data = {
 	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
 	.status		= realview_mmc_status,
 	.gpio_wp	= 17,
 	.gpio_cd	= 16,
 };
 
-struct mmc_platform_data realview_mmc1_plat_data = {
+struct mmci_platform_data realview_mmc1_plat_data = {
 	.ocr_mask	= MMC_VDD_32_33|MMC_VDD_33_34,
 	.status		= realview_mmc_status,
 	.gpio_wp	= 19,
@@ -296,31 +296,31 @@ static struct clk ref24_clk = {
 
 static struct clk_lookup lookups[] = {
 	{	/* UART0 */
-		.dev_id		= "dev:f1",
+		.dev_id		= "dev:uart0",
 		.clk		= &ref24_clk,
 	}, {	/* UART1 */
-		.dev_id		= "dev:f2",
+		.dev_id		= "dev:uart1",
 		.clk		= &ref24_clk,
 	}, {	/* UART2 */
-		.dev_id		= "dev:f3",
+		.dev_id		= "dev:uart2",
 		.clk		= &ref24_clk,
 	}, {	/* UART3 */
-		.dev_id		= "fpga:09",
+		.dev_id		= "fpga:uart3",
 		.clk		= &ref24_clk,
 	}, {	/* KMI0 */
-		.dev_id		= "fpga:06",
+		.dev_id		= "fpga:kmi0",
 		.clk		= &ref24_clk,
 	}, {	/* KMI1 */
-		.dev_id		= "fpga:07",
+		.dev_id		= "fpga:kmi1",
 		.clk		= &ref24_clk,
 	}, {	/* MMC0 */
-		.dev_id		= "fpga:05",
+		.dev_id		= "fpga:mmc0",
 		.clk		= &ref24_clk,
 	}, {	/* EB:CLCD */
-		.dev_id		= "dev:20",
+		.dev_id		= "dev:clcd",
 		.clk		= &oscvco_clk,
 	}, {	/* PB:CLCD */
-		.dev_id		= "issp:20",
+		.dev_id		= "issp:clcd",
 		.clk		= &oscvco_clk,
 	}
 };

arch/arm/mach-realview/core.h

@@ -47,8 +47,8 @@ static struct amba_device name##_device = {			\
 extern struct platform_device realview_flash_device;
 extern struct platform_device realview_cf_device;
 extern struct platform_device realview_i2c_device;
-extern struct mmc_platform_data realview_mmc0_plat_data;
-extern struct mmc_platform_data realview_mmc1_plat_data;
+extern struct mmci_platform_data realview_mmc0_plat_data;
+extern struct mmci_platform_data realview_mmc1_plat_data;
 extern struct clcd_board clcd_plat_data;
 extern void __iomem *gic_cpu_base_addr;
 extern void __iomem *timer0_va_base;

arch/arm/mach-realview/realview_eb.c

@@ -24,6 +24,7 @@
 #include <linux/sysdev.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
 #include <linux/io.h>
 
 #include <mach/hardware.h>
@@ -37,7 +38,6 @@
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 #include <asm/mach/time.h>
 
 #include <mach/board-eb.h>
@@ -193,27 +193,27 @@ static struct pl061_platform_data gpio2_plat_data = {
 #define EB_SSP_DMA	{ 9, 8 }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,  "fpga:04", AACI,     NULL);
-AMBA_DEVICE(mmc0,  "fpga:05", MMCI0,    &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,  "fpga:06", KMI0,     NULL);
-AMBA_DEVICE(kmi1,  "fpga:07", KMI1,     NULL);
-AMBA_DEVICE(uart3, "fpga:09", EB_UART3, NULL);
+AMBA_DEVICE(aaci,  "fpga:aaci",  AACI,     NULL);
+AMBA_DEVICE(mmc0,  "fpga:mmc0",  MMCI0,    &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0,  "fpga:kmi0",  KMI0,     NULL);
+AMBA_DEVICE(kmi1,  "fpga:kmi1",  KMI1,     NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,   "dev:00",  EB_SMC,   NULL);
-AMBA_DEVICE(clcd,  "dev:20",  EB_CLCD,  &clcd_plat_data);
-AMBA_DEVICE(dmac,  "dev:30",  DMAC,     NULL);
-AMBA_DEVICE(sctl,  "dev:e0",  SCTL,     NULL);
-AMBA_DEVICE(wdog,  "dev:e1",  EB_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4",  EB_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5",  GPIO1,    &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6",  GPIO2,    &gpio2_plat_data);
-AMBA_DEVICE(rtc,   "dev:e8",  EB_RTC,   NULL);
-AMBA_DEVICE(sci0,  "dev:f0",  SCI,      NULL);
-AMBA_DEVICE(uart0, "dev:f1",  EB_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2",  EB_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3",  EB_UART2, NULL);
-AMBA_DEVICE(ssp0,  "dev:f4",  EB_SSP,   NULL);
+AMBA_DEVICE(smc,   "dev:smc",   EB_SMC,   NULL);
+AMBA_DEVICE(clcd,  "dev:clcd",  EB_CLCD,  &clcd_plat_data);
+AMBA_DEVICE(dmac,  "dev:dmac",  DMAC,     NULL);
+AMBA_DEVICE(sctl,  "dev:sctl",  SCTL,     NULL);
+AMBA_DEVICE(wdog,  "dev:wdog",  EB_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1,    &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2,    &gpio2_plat_data);
+AMBA_DEVICE(rtc,   "dev:rtc",   EB_RTC,   NULL);
+AMBA_DEVICE(sci0,  "dev:sci0",  SCI,      NULL);
+AMBA_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
+AMBA_DEVICE(ssp0,  "dev:ssp0",  EB_SSP,   NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,

arch/arm/mach-realview/realview_pb1176.c

@@ -24,6 +24,7 @@
 #include <linux/sysdev.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
 #include <linux/io.h>
 
 #include <mach/hardware.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 #include <asm/mach/time.h>
 
 #include <mach/board-pb1176.h>
@@ -170,29 +170,29 @@ static struct pl061_platform_data gpio2_plat_data = {
 #define PB1176_SSP_DMA		{ 9, 8 }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:04",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:05",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:06",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:07",	KMI1,		NULL);
-AMBA_DEVICE(uart3,	"fpga:09",	PB1176_UART3,	NULL);
+AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+AMBA_DEVICE(uart3,	"fpga:uart3",	PB1176_UART3,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:00",	PB1176_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:e0",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:e1",	PB1176_WATCHDOG,	NULL);
-AMBA_DEVICE(gpio0,	"dev:e4",	PB1176_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:e5",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:e6",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:e8",	PB1176_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:f0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:f1",	PB1176_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:f2",	PB1176_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:f3",	PB1176_UART2,	NULL);
-AMBA_DEVICE(ssp0,	"dev:f4",	PB1176_SSP,	NULL);
+AMBA_DEVICE(smc,	"dev:smc",	PB1176_SMC,	NULL);
+AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+AMBA_DEVICE(wdog,	"dev:wdog",	PB1176_WATCHDOG,	NULL);
+AMBA_DEVICE(gpio0,	"dev:gpio0",	PB1176_GPIO0,	&gpio0_plat_data);
+AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+AMBA_DEVICE(rtc,	"dev:rtc",	PB1176_RTC,	NULL);
+AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+AMBA_DEVICE(uart0,	"dev:uart0",	PB1176_UART0,	NULL);
+AMBA_DEVICE(uart1,	"dev:uart1",	PB1176_UART1,	NULL);
+AMBA_DEVICE(uart2,	"dev:uart2",	PB1176_UART2,	NULL);
+AMBA_DEVICE(ssp0,	"dev:ssp0",	PB1176_SSP,	NULL);
 
 /* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd,	"issp:20",	PB1176_CLCD,	&clcd_plat_data);
-//AMBA_DEVICE(dmac,	"issp:30",	PB1176_DMAC,	NULL);
+AMBA_DEVICE(clcd,	"issp:clcd",	PB1176_CLCD,	&clcd_plat_data);
+//AMBA_DEVICE(dmac,	"issp:dmac",	PB1176_DMAC,	NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 //	&dmac_device,

arch/arm/mach-realview/realview_pb11mp.c

@@ -24,6 +24,7 @@
 #include <linux/sysdev.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
 #include <linux/io.h>
 
 #include <mach/hardware.h>
@@ -38,7 +39,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 #include <asm/mach/time.h>
 
 #include <mach/board-pb11mp.h>
@@ -172,29 +172,29 @@ static struct pl061_platform_data gpio2_plat_data = {
 #define PB11MP_SSP_DMA		{ 9, 8 }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:04",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:05",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:06",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:07",	KMI1,		NULL);
-AMBA_DEVICE(uart3,	"fpga:09",	PB11MP_UART3,	NULL);
+AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+AMBA_DEVICE(uart3,	"fpga:uart3",	PB11MP_UART3,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:00",	PB11MP_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:e0",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:e1",	PB11MP_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0,	"dev:e4",	PB11MP_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:e5",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:e6",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:e8",	PB11MP_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:f0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:f1",	PB11MP_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:f2",	PB11MP_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:f3",	PB11MP_UART2,	NULL);
-AMBA_DEVICE(ssp0,	"dev:f4",	PB11MP_SSP,	NULL);
+AMBA_DEVICE(smc,	"dev:smc",	PB11MP_SMC,	NULL);
+AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+AMBA_DEVICE(wdog,	"dev:wdog",	PB11MP_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0,	"dev:gpio0",	PB11MP_GPIO0,	&gpio0_plat_data);
+AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+AMBA_DEVICE(rtc,	"dev:rtc",	PB11MP_RTC,	NULL);
+AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+AMBA_DEVICE(uart0,	"dev:uart0",	PB11MP_UART0,	NULL);
+AMBA_DEVICE(uart1,	"dev:uart1",	PB11MP_UART1,	NULL);
+AMBA_DEVICE(uart2,	"dev:uart2",	PB11MP_UART2,	NULL);
+AMBA_DEVICE(ssp0,	"dev:ssp0",	PB11MP_SSP,	NULL);
 
 /* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd,	"issp:20",	PB11MP_CLCD,	&clcd_plat_data);
-AMBA_DEVICE(dmac,	"issp:30",	DMAC,		NULL);
+AMBA_DEVICE(clcd,	"issp:clcd",	PB11MP_CLCD,	&clcd_plat_data);
+AMBA_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,

arch/arm/mach-realview/realview_pba8.c

@@ -24,6 +24,7 @@
 #include <linux/sysdev.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
 #include <linux/io.h>
 
 #include <asm/irq.h>
@@ -34,7 +35,6 @@
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 #include <asm/mach/time.h>
 
 #include <mach/hardware.h>
@@ -162,29 +162,29 @@ static struct pl061_platform_data gpio2_plat_data = {
 #define PBA8_SSP_DMA		{ 9, 8 }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:04",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:05",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:06",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:07",	KMI1,		NULL);
-AMBA_DEVICE(uart3,	"fpga:09",	PBA8_UART3,	NULL);
+AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+AMBA_DEVICE(uart3,	"fpga:uart3",	PBA8_UART3,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:00",	PBA8_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:e0",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:e1",	PBA8_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0,	"dev:e4",	PBA8_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:e5",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:e6",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:e8",	PBA8_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:f0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:f1",	PBA8_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:f2",	PBA8_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:f3",	PBA8_UART2,	NULL);
-AMBA_DEVICE(ssp0,	"dev:f4",	PBA8_SSP,	NULL);
+AMBA_DEVICE(smc,	"dev:smc",	PBA8_SMC,	NULL);
+AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+AMBA_DEVICE(wdog,	"dev:wdog",	PBA8_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0,	"dev:gpio0",	PBA8_GPIO0,	&gpio0_plat_data);
+AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+AMBA_DEVICE(rtc,	"dev:rtc",	PBA8_RTC,	NULL);
+AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+AMBA_DEVICE(uart0,	"dev:uart0",	PBA8_UART0,	NULL);
+AMBA_DEVICE(uart1,	"dev:uart1",	PBA8_UART1,	NULL);
+AMBA_DEVICE(uart2,	"dev:uart2",	PBA8_UART2,	NULL);
+AMBA_DEVICE(ssp0,	"dev:ssp0",	PBA8_SSP,	NULL);
 
 /* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd,	"issp:20",	PBA8_CLCD,	&clcd_plat_data);
-AMBA_DEVICE(dmac,	"issp:30",	DMAC,		NULL);
+AMBA_DEVICE(clcd,	"issp:clcd",	PBA8_CLCD,	&clcd_plat_data);
+AMBA_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,

arch/arm/mach-realview/realview_pbx.c

@@ -23,6 +23,7 @@
 #include <linux/sysdev.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
 #include <linux/io.h>
 
 #include <asm/irq.h>
@@ -34,7 +35,6 @@
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 #include <asm/mach/time.h>
 
 #include <mach/hardware.h>
@@ -182,29 +182,29 @@ static struct pl061_platform_data gpio2_plat_data = {
 #define PBX_SSP_DMA		{ 9, 8 }
 
 /* FPGA Primecells */
-AMBA_DEVICE(aaci,	"fpga:04",	AACI,		NULL);
-AMBA_DEVICE(mmc0,	"fpga:05",	MMCI0,		&realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0,	"fpga:06",	KMI0,		NULL);
-AMBA_DEVICE(kmi1,	"fpga:07",	KMI1,		NULL);
-AMBA_DEVICE(uart3,	"fpga:09",	PBX_UART3,	NULL);
+AMBA_DEVICE(aaci,	"fpga:aaci",	AACI,		NULL);
+AMBA_DEVICE(mmc0,	"fpga:mmc0",	MMCI0,		&realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0,	"fpga:kmi0",	KMI0,		NULL);
+AMBA_DEVICE(kmi1,	"fpga:kmi1",	KMI1,		NULL);
+AMBA_DEVICE(uart3,	"fpga:uart3",	PBX_UART3,	NULL);
 
 /* DevChip Primecells */
-AMBA_DEVICE(smc,	"dev:00",	PBX_SMC,	NULL);
-AMBA_DEVICE(sctl,	"dev:e0",	SCTL,		NULL);
-AMBA_DEVICE(wdog,	"dev:e1",	PBX_WATCHDOG, 	NULL);
-AMBA_DEVICE(gpio0,	"dev:e4",	PBX_GPIO0,	&gpio0_plat_data);
-AMBA_DEVICE(gpio1,	"dev:e5",	GPIO1,		&gpio1_plat_data);
-AMBA_DEVICE(gpio2,	"dev:e6",	GPIO2,		&gpio2_plat_data);
-AMBA_DEVICE(rtc,	"dev:e8",	PBX_RTC,	NULL);
-AMBA_DEVICE(sci0,	"dev:f0",	SCI,		NULL);
-AMBA_DEVICE(uart0,	"dev:f1",	PBX_UART0,	NULL);
-AMBA_DEVICE(uart1,	"dev:f2",	PBX_UART1,	NULL);
-AMBA_DEVICE(uart2,	"dev:f3",	PBX_UART2,	NULL);
-AMBA_DEVICE(ssp0,	"dev:f4",	PBX_SSP,	NULL);
+AMBA_DEVICE(smc,	"dev:smc",	PBX_SMC,	NULL);
+AMBA_DEVICE(sctl,	"dev:sctl",	SCTL,		NULL);
+AMBA_DEVICE(wdog,	"dev:wdog",	PBX_WATCHDOG, 	NULL);
+AMBA_DEVICE(gpio0,	"dev:gpio0",	PBX_GPIO0,	&gpio0_plat_data);
+AMBA_DEVICE(gpio1,	"dev:gpio1",	GPIO1,		&gpio1_plat_data);
+AMBA_DEVICE(gpio2,	"dev:gpio2",	GPIO2,		&gpio2_plat_data);
+AMBA_DEVICE(rtc,	"dev:rtc",	PBX_RTC,	NULL);
+AMBA_DEVICE(sci0,	"dev:sci0",	SCI,		NULL);
+AMBA_DEVICE(uart0,	"dev:uart0",	PBX_UART0,	NULL);
+AMBA_DEVICE(uart1,	"dev:uart1",	PBX_UART1,	NULL);
+AMBA_DEVICE(uart2,	"dev:uart2",	PBX_UART2,	NULL);
+AMBA_DEVICE(ssp0,	"dev:ssp0",	PBX_SSP,	NULL);
 
 /* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd,	"issp:20",	PBX_CLCD,	&clcd_plat_data);
-AMBA_DEVICE(dmac,	"issp:30",	DMAC,		NULL);
+AMBA_DEVICE(clcd,	"issp:clcd",	PBX_CLCD,	&clcd_plat_data);
+AMBA_DEVICE(dmac,	"issp:dmac",	DMAC,		NULL);
 
 static struct amba_device *amba_devs[] __initdata = {
 	&dmac_device,

arch/arm/mach-s3c2410/Kconfig

@@ -77,6 +77,7 @@ config ARCH_H1940
 	select CPU_S3C2410
 	select PM_H1940 if PM
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using the HP IPAQ H1940
 
@@ -89,6 +90,7 @@ config MACH_N30
 	bool "Acer N30 family"
 	select CPU_S3C2410
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you want suppt for the Acer N30, Acer N35,
 	  Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs.
@@ -103,6 +105,7 @@ config ARCH_BAST
 	select S3C24XX_DCLK
 	select ISA
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using the Simtec Electronics EB2410ITX
 	  development board (also known as BAST)
@@ -111,6 +114,7 @@ config MACH_OTOM
  	bool "NexVision OTOM Board"
  	select CPU_S3C2410
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
  	  Say Y here if you are using the Nex Vision OTOM board
 
@@ -154,6 +158,7 @@ config MACH_QT2410
 	bool "QT2410"
 	select CPU_S3C2410
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	   Say Y here if you are using the Armzone QT2410
 

arch/arm/mach-s3c2412/Kconfig

@@ -48,6 +48,7 @@ config MACH_JIVE
 	bool "Logitech Jive"
 	select CPU_S3C2412
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using the Logitech Jive.
 
@@ -61,6 +62,7 @@ config MACH_SMDK2413
 	select MACH_S3C2413
 	select MACH_SMDK
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using an SMDK2413
 
@@ -84,6 +86,7 @@ config MACH_VSTMS
 	bool "VMSTMS"
 	select CPU_S3C2412
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using an VSTMS board
 

arch/arm/mach-s3c2440/Kconfig

@@ -48,6 +48,7 @@ config MACH_OSIRIS
 	select S3C2440_XTAL_12000000
 	select S3C2410_IOTIMING if S3C2440_CPUFREQ
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using the Simtec IM2440D20 module, also
 	  known as the Osiris.
@@ -57,6 +58,7 @@ config MACH_RX3715
 	select CPU_S3C2440
 	select S3C2440_XTAL_16934400
 	select PM_H1940 if PM
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using the HP iPAQ rx3715.
 
@@ -66,6 +68,7 @@ config ARCH_S3C2440
 	select S3C2440_XTAL_16934400
 	select MACH_SMDK
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using the SMDK2440.
 
@@ -74,6 +77,7 @@ config MACH_NEXCODER_2440
  	select CPU_S3C2440
 	select S3C2440_XTAL_12000000
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
  	  Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
 
@@ -88,6 +92,7 @@ config MACH_AT2440EVB
 	bool "Avantech AT2440EVB development board"
 	select CPU_S3C2440
 	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
 	help
 	  Say Y here if you are using the AT2440EVB development board
 
@@ -97,6 +102,7 @@ config MACH_MINI2440
 	select EEPROM_AT24
 	select LEDS_TRIGGER_BACKLIGHT
 	select SND_S3C24XX_SOC_S3C24XX_UDA134X
+	select S3C_DEV_NAND
 	help
 	  Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
 	  available via various sources. It can come with a 3.5" or 7" touch LCD.