Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: unbind all interfaces before rebinding them
  USB: serial: digi_acceleport: Eliminate a NULL pointer dereference
  usb: fix ehci_hcd build failure when both generic-OF and xilinx is selected
  USB: cdc-acm: fix resource reclaim in error path of acm_probe
  USB: ftdi_sio: fix DTR/RTS line modes
  USB: s3c-hsotg: Ensure FIFOs are fully flushed after layout
  USB: s3c-hsotg: SoftDisconnect minimum 3ms
  USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
  USB: s3c_hsotg: define USB_GADGET_DUALSPEED in Kconfig
  USB: s3c: Enable soft disconnect during initialization
  USB: xhci: Print NEC firmware version.
  USB: xhci: Wait for host to start running.
  USB: xhci: Wait for controller to be ready after reset.
  USB: isp1362: fix inw warning on Blackfin systems
  USB: mos7840: fix null-pointer dereference

drivers/usb/class/cdc-acm.c

@@ -1201,7 +1201,7 @@ made_compressed_probe:
 		if (rcv->urb == NULL) {
 			dev_dbg(&intf->dev,
 				"out of memory (read urbs usb_alloc_urb)\n");
-			goto alloc_fail7;
+			goto alloc_fail6;
 		}
 
 		rcv->urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
@@ -1225,7 +1225,7 @@ made_compressed_probe:
 		if (snd->urb == NULL) {
 			dev_dbg(&intf->dev,
 				"out of memory (write urbs usb_alloc_urb)");
-			goto alloc_fail7;
+			goto alloc_fail8;
 		}
 
 		if (usb_endpoint_xfer_int(epwrite))
@@ -1264,6 +1264,7 @@ made_compressed_probe:
 		i = device_create_file(&intf->dev,
 						&dev_attr_iCountryCodeRelDate);
 		if (i < 0) {
+			device_remove_file(&intf->dev, &dev_attr_wCountryCodes);
 			kfree(acm->country_codes);
 			goto skip_countries;
 		}
@@ -1300,6 +1301,7 @@ alloc_fail8:
 		usb_free_urb(acm->wb[i].urb);
 alloc_fail7:
 	acm_read_buffers_free(acm);
+alloc_fail6:
 	for (i = 0; i < num_rx_buf; i++)
 		usb_free_urb(acm->ru[i].urb);
 	usb_free_urb(acm->ctrlurb);

drivers/usb/core/driver.c

@@ -1328,6 +1328,7 @@ int usb_resume(struct device *dev, pm_message_t msg)
 
 	/* For all other calls, take the device back to full power and
 	 * tell the PM core in case it was autosuspended previously.
+	 * Unbind the interfaces that will need rebinding later.
 	 */
 	} else {
 		status = usb_resume_both(udev, msg);
@@ -1336,6 +1337,7 @@ int usb_resume(struct device *dev, pm_message_t msg)
 			pm_runtime_set_active(dev);
 			pm_runtime_enable(dev);
 			udev->last_busy = jiffies;
+			do_unbind_rebind(udev, DO_REBIND);
 		}
 	}
 

drivers/usb/gadget/Kconfig

@@ -295,6 +295,7 @@ config USB_GADGET_S3C_HSOTG
 	boolean "S3C HS/OtG USB Device controller"
 	depends on S3C_DEV_USB_HSOTG
 	select USB_GADGET_S3C_HSOTG_PIO
+	select USB_GADGET_DUALSPEED
 	help
 	  The Samsung S3C64XX USB2.0 high-speed gadget controller
 	  integrated into the S3C64XX series SoC.

drivers/usb/gadget/s3c-hsotg.c

@@ -297,6 +297,12 @@ static void s3c_hsotg_ctrl_epint(struct s3c_hsotg *hsotg,
  */
 static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)
 {
+	unsigned int ep;
+	unsigned int addr;
+	unsigned int size;
+	int timeout;
+	u32 val;
+
 	/* the ryu 2.6.24 release ahs
 	   writel(0x1C0, hsotg->regs + S3C_GRXFSIZ);
 	   writel(S3C_GNPTXFSIZ_NPTxFStAddr(0x200) |
@@ -310,6 +316,51 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)
 	writel(S3C_GNPTXFSIZ_NPTxFStAddr(2048) |
 	       S3C_GNPTXFSIZ_NPTxFDep(0x1C0),
 	       hsotg->regs + S3C_GNPTXFSIZ);
+
+	/* arange all the rest of the TX FIFOs, as some versions of this
+	 * block have overlapping default addresses. This also ensures
+	 * that if the settings have been changed, then they are set to
+	 * known values. */
+
+	/* start at the end of the GNPTXFSIZ, rounded up */
+	addr = 2048 + 1024;
+	size = 768;
+
+	/* currently we allocate TX FIFOs for all possible endpoints,
+	 * and assume that they are all the same size. */
+
+	for (ep = 0; ep <= 15; ep++) {
+		val = addr;
+		val |= size << S3C_DPTXFSIZn_DPTxFSize_SHIFT;
+		addr += size;
+
+		writel(val, hsotg->regs + S3C_DPTXFSIZn(ep));
+	}
+
+	/* according to p428 of the design guide, we need to ensure that
+	 * all fifos are flushed before continuing */
+
+	writel(S3C_GRSTCTL_TxFNum(0x10) | S3C_GRSTCTL_TxFFlsh |
+	       S3C_GRSTCTL_RxFFlsh, hsotg->regs + S3C_GRSTCTL);
+
+	/* wait until the fifos are both flushed */
+	timeout = 100;
+	while (1) {
+		val = readl(hsotg->regs + S3C_GRSTCTL);
+
+		if ((val & (S3C_GRSTCTL_TxFFlsh | S3C_GRSTCTL_RxFFlsh)) == 0)
+			break;
+
+		if (--timeout == 0) {
+			dev_err(hsotg->dev,
+				"%s: timeout flushing fifos (GRSTCTL=%08x)\n",
+				__func__, val);
+		}
+
+		udelay(1);
+	}
+
+	dev_dbg(hsotg->dev, "FIFOs reset, timeout at %d\n", timeout);
 }
 
 /**
@@ -2574,6 +2625,9 @@ int usb_gadget_register_driver(struct usb_gadget_driver *driver)
 	writel(S3C_DCTL_CGOUTNak | S3C_DCTL_CGNPInNAK,
 	       hsotg->regs + S3C_DCTL);
 
+	/* must be at-least 3ms to allow bus to see disconnect */
+	msleep(3);
+
 	/* remove the soft-disconnect and let's go */
 	__bic32(hsotg->regs + S3C_DCTL, S3C_DCTL_SftDiscon);
 
@@ -2730,6 +2784,9 @@ static void s3c_hsotg_init(struct s3c_hsotg *hsotg)
 
 	writel(0, hsotg->regs + S3C_DAINTMSK);
 
+	/* Be in disconnected state until gadget is registered */
+	__orr32(hsotg->regs + S3C_DCTL, S3C_DCTL_SftDiscon);
+
 	if (0) {
 		/* post global nak until we're ready */
 		writel(S3C_DCTL_SGNPInNAK | S3C_DCTL_SGOUTNak,

drivers/usb/host/ehci-hcd.c

@@ -1135,7 +1135,7 @@ MODULE_LICENSE ("GPL");
 
 #ifdef CONFIG_XPS_USB_HCD_XILINX
 #include "ehci-xilinx-of.c"
-#define OF_PLATFORM_DRIVER	ehci_hcd_xilinx_of_driver
+#define XILINX_OF_PLATFORM_DRIVER	ehci_hcd_xilinx_of_driver
 #endif
 
 #ifdef CONFIG_PLAT_ORION
@@ -1159,7 +1159,8 @@ MODULE_LICENSE ("GPL");
 #endif
 
 #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
-    !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER)
+    !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
+    !defined(XILINX_OF_PLATFORM_DRIVER)
 #error "missing bus glue for ehci-hcd"
 #endif
 
@@ -1213,10 +1214,20 @@ static int __init ehci_hcd_init(void)
 	if (retval < 0)
 		goto clean3;
 #endif
+
+#ifdef XILINX_OF_PLATFORM_DRIVER
+	retval = of_register_platform_driver(&XILINX_OF_PLATFORM_DRIVER);
+	if (retval < 0)
+		goto clean4;
+#endif
 	return retval;
 
+#ifdef XILINX_OF_PLATFORM_DRIVER
+	/* of_unregister_platform_driver(&XILINX_OF_PLATFORM_DRIVER); */
+clean4:
+#endif
 #ifdef OF_PLATFORM_DRIVER
-	/* of_unregister_platform_driver(&OF_PLATFORM_DRIVER); */
+	of_unregister_platform_driver(&OF_PLATFORM_DRIVER);
 clean3:
 #endif
 #ifdef PS3_SYSTEM_BUS_DRIVER
@@ -1243,6 +1254,9 @@ module_init(ehci_hcd_init);
 
 static void __exit ehci_hcd_cleanup(void)
 {
+#ifdef XILINX_OF_PLATFORM_DRIVER
+	of_unregister_platform_driver(&XILINX_OF_PLATFORM_DRIVER);
+#endif
 #ifdef OF_PLATFORM_DRIVER
 	of_unregister_platform_driver(&OF_PLATFORM_DRIVER);
 #endif

drivers/usb/host/isp1362.h

@@ -65,7 +65,7 @@ static inline void delayed_insw(unsigned int addr, void *buf, int len)
 	unsigned short *bp = (unsigned short *)buf;
 	while (len--) {
 		DUMMY_DELAY_ACCESS;
-		*bp++ = inw((void *)addr);
+		*bp++ = inw(addr);
 	}
 }
 

drivers/usb/host/xhci-pci.c

@@ -78,6 +78,8 @@ static int xhci_pci_setup(struct usb_hcd *hcd)
 			xhci_dbg(xhci, "QUIRK: Fresco Logic xHC needs configure"
 					" endpoint cmd after reset endpoint\n");
 	}
+	if (pdev->vendor == PCI_VENDOR_ID_NEC)
+		xhci->quirks |= XHCI_NEC_HOST;
 
 	/* Make sure the HC is halted. */
 	retval = xhci_halt(xhci);

drivers/usb/host/xhci-ring.c

@@ -1071,6 +1071,15 @@ bandwidth_change:
 			xhci_warn(xhci, "Reset device command completion "
 					"for disabled slot %u\n", slot_id);
 		break;
+	case TRB_TYPE(TRB_NEC_GET_FW):
+		if (!(xhci->quirks & XHCI_NEC_HOST)) {
+			xhci->error_bitmask |= 1 << 6;
+			break;
+		}
+		xhci_dbg(xhci, "NEC firmware version %2x.%02x\n",
+				NEC_FW_MAJOR(event->status),
+				NEC_FW_MINOR(event->status));
+		break;
 	default:
 		/* Skip over unknown commands on the event ring */
 		xhci->error_bitmask |= 1 << 6;
@@ -1079,6 +1088,17 @@ bandwidth_change:
 	inc_deq(xhci, xhci->cmd_ring, false);
 }
 
+static void handle_vendor_event(struct xhci_hcd *xhci,
+		union xhci_trb *event)
+{
+	u32 trb_type;
+
+	trb_type = TRB_FIELD_TO_TYPE(event->generic.field[3]);
+	xhci_dbg(xhci, "Vendor specific event TRB type = %u\n", trb_type);
+	if (trb_type == TRB_NEC_CMD_COMP && (xhci->quirks & XHCI_NEC_HOST))
+		handle_cmd_completion(xhci, &event->event_cmd);
+}
+
 static void handle_port_status(struct xhci_hcd *xhci,
 		union xhci_trb *event)
 {
@@ -1659,7 +1679,10 @@ void xhci_handle_event(struct xhci_hcd *xhci)
 			update_ptrs = 0;
 		break;
 	default:
-		xhci->error_bitmask |= 1 << 3;
+		if ((event->event_cmd.flags & TRB_TYPE_BITMASK) >= TRB_TYPE(48))
+			handle_vendor_event(xhci, event);
+		else
+			xhci->error_bitmask |= 1 << 3;
 	}
 	/* Any of the above functions may drop and re-acquire the lock, so check
 	 * to make sure a watchdog timer didn't mark the host as non-responsive.
@@ -2378,6 +2401,12 @@ int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 			false);
 }
 
+int xhci_queue_vendor_command(struct xhci_hcd *xhci,
+		u32 field1, u32 field2, u32 field3, u32 field4)
+{
+	return queue_command(xhci, field1, field2, field3, field4, false);
+}
+
 /* Queue a reset device command TRB */
 int xhci_queue_reset_device(struct xhci_hcd *xhci, u32 slot_id)
 {

drivers/usb/host/xhci.c

@@ -105,6 +105,33 @@ int xhci_halt(struct xhci_hcd *xhci)
 			STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC);
 }
 
+/*
+ * Set the run bit and wait for the host to be running.
+ */
+int xhci_start(struct xhci_hcd *xhci)
+{
+	u32 temp;
+	int ret;
+
+	temp = xhci_readl(xhci, &xhci->op_regs->command);
+	temp |= (CMD_RUN);
+	xhci_dbg(xhci, "// Turn on HC, cmd = 0x%x.\n",
+			temp);
+	xhci_writel(xhci, temp, &xhci->op_regs->command);
+
+	/*
+	 * Wait for the HCHalted Status bit to be 0 to indicate the host is
+	 * running.
+	 */
+	ret = handshake(xhci, &xhci->op_regs->status,
+			STS_HALT, 0, XHCI_MAX_HALT_USEC);
+	if (ret == -ETIMEDOUT)
+		xhci_err(xhci, "Host took too long to start, "
+				"waited %u microseconds.\n",
+				XHCI_MAX_HALT_USEC);
+	return ret;
+}
+
 /*
  * Reset a halted HC, and set the internal HC state to HC_STATE_HALT.
  *
@@ -116,6 +143,7 @@ int xhci_reset(struct xhci_hcd *xhci)
 {
 	u32 command;
 	u32 state;
+	int ret;
 
 	state = xhci_readl(xhci, &xhci->op_regs->status);
 	if ((state & STS_HALT) == 0) {
@@ -130,7 +158,17 @@ int xhci_reset(struct xhci_hcd *xhci)
 	/* XXX: Why does EHCI set this here?  Shouldn't other code do this? */
 	xhci_to_hcd(xhci)->state = HC_STATE_HALT;
 
-	return handshake(xhci, &xhci->op_regs->command, CMD_RESET, 0, 250 * 1000);
+	ret = handshake(xhci, &xhci->op_regs->command,
+			CMD_RESET, 0, 250 * 1000);
+	if (ret)
+		return ret;
+
+	xhci_dbg(xhci, "Wait for controller to be ready for doorbell rings\n");
+	/*
+	 * xHCI cannot write to any doorbells or operational registers other
+	 * than status until the "Controller Not Ready" flag is cleared.
+	 */
+	return handshake(xhci, &xhci->op_regs->status, STS_CNR, 0, 250 * 1000);
 }
 
 
@@ -448,17 +486,20 @@ int xhci_run(struct usb_hcd *hcd)
 
 	if (NUM_TEST_NOOPS > 0)
 		doorbell = xhci_setup_one_noop(xhci);
+	if (xhci->quirks & XHCI_NEC_HOST)
+		xhci_queue_vendor_command(xhci, 0, 0, 0,
+				TRB_TYPE(TRB_NEC_GET_FW));
+
+	if (xhci_start(xhci)) {
+		xhci_halt(xhci);
+		return -ENODEV;
+	}
 
-	temp = xhci_readl(xhci, &xhci->op_regs->command);
-	temp |= (CMD_RUN);
-	xhci_dbg(xhci, "// Turn on HC, cmd = 0x%x.\n",
-			temp);
-	xhci_writel(xhci, temp, &xhci->op_regs->command);
-	/* Flush PCI posted writes */
-	temp = xhci_readl(xhci, &xhci->op_regs->command);
 	xhci_dbg(xhci, "// @%p = 0x%x\n", &xhci->op_regs->command, temp);
 	if (doorbell)
 		(*doorbell)(xhci);
+	if (xhci->quirks & XHCI_NEC_HOST)
+		xhci_ring_cmd_db(xhci);
 
 	xhci_dbg(xhci, "Finished xhci_run\n");
 	return 0;

drivers/usb/host/xhci.h

@@ -925,6 +925,7 @@ union xhci_trb {
 /* TRB bit mask */
 #define	TRB_TYPE_BITMASK	(0xfc00)
 #define TRB_TYPE(p)		((p) << 10)
+#define TRB_FIELD_TO_TYPE(p)	(((p) & TRB_TYPE_BITMASK) >> 10)
 /* TRB type IDs */
 /* bulk, interrupt, isoc scatter/gather, and control data stage */
 #define TRB_NORMAL		1
@@ -992,6 +993,14 @@ union xhci_trb {
 #define TRB_MFINDEX_WRAP	39
 /* TRB IDs 40-47 reserved, 48-63 is vendor-defined */
 
+/* Nec vendor-specific command completion event. */
+#define	TRB_NEC_CMD_COMP	48
+/* Get NEC firmware revision. */
+#define	TRB_NEC_GET_FW		49
+
+#define NEC_FW_MINOR(p)		(((p) >> 0) & 0xff)
+#define NEC_FW_MAJOR(p)		(((p) >> 8) & 0xff)
+
 /*
  * TRBS_PER_SEGMENT must be a multiple of 4,
  * since the command ring is 64-byte aligned.
@@ -1172,6 +1181,7 @@ struct xhci_hcd {
 	unsigned int		quirks;
 #define	XHCI_LINK_TRB_QUIRK	(1 << 0)
 #define XHCI_RESET_EP_QUIRK	(1 << 1)
+#define XHCI_NEC_HOST		(1 << 2)
 };
 
 /* For testing purposes */
@@ -1379,6 +1389,8 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci);
 int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id);
 int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 		u32 slot_id);
+int xhci_queue_vendor_command(struct xhci_hcd *xhci,
+		u32 field1, u32 field2, u32 field3, u32 field4);
 int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, int slot_id,
 		unsigned int ep_index);
 int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,

drivers/usb/serial/digi_acceleport.c

@@ -1239,8 +1239,7 @@ static void digi_write_bulk_callback(struct urb *urb)
 
 	/* port and serial sanity check */
 	if (port == NULL || (priv = usb_get_serial_port_data(port)) == NULL) {
-		dev_err(&port->dev,
-			"%s: port or port->private is NULL, status=%d\n",
+		pr_err("%s: port or port->private is NULL, status=%d\n",
 			__func__, status);
 		return;
 	}

drivers/usb/serial/ftdi_sio.c

@@ -2005,6 +2005,8 @@ static void ftdi_set_termios(struct tty_struct *tty,
 				"urb failed to set to rts/cts flow control\n");
 		}
 
+		/* raise DTR/RTS */
+		set_mctrl(port, TIOCM_DTR | TIOCM_RTS);
 	} else {
 		/*
 		 * Xon/Xoff code
@@ -2052,6 +2054,8 @@ static void ftdi_set_termios(struct tty_struct *tty,
 			}
 		}
 
+		/* lower DTR/RTS */
+		clear_mctrl(port, TIOCM_DTR | TIOCM_RTS);
 	}
 	return;
 }

drivers/usb/serial/mos7840.c

@@ -730,7 +730,6 @@ static void mos7840_bulk_in_callback(struct urb *urb)
 	mos7840_port = urb->context;
 	if (!mos7840_port) {
 		dbg("%s", "NULL mos7840_port pointer");
-		mos7840_port->read_urb_busy = false;
 		return;
 	}