Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

CREDITS

@@ -2166,7 +2166,6 @@ D: Initial implementation of VC's, pty's and select()
 
 N: Pavel Machek
 E: pavel@ucw.cz
-E: pavel@suse.cz
 D: Softcursor for vga, hypertech cdrom support, vcsa bugfix, nbd
 D: sun4/330 port, capabilities for elf, speedup for rm on ext2, USB,
 D: work on suspend-to-ram/disk, killing duplicates from ioctl32

Documentation/ABI/testing/sysfs-bus-pci

@@ -1,3 +1,46 @@
+What:		/sys/bus/pci/drivers/.../bind
+Date:		December 2003
+Contact:	linux-pci@vger.kernel.org
+Description:
+		Writing a device location to this file will cause
+		the driver to attempt to bind to the device found at
+		this location.	This is useful for overriding default
+		bindings.  The format for the location is: DDDD:BB:DD.F.
+		That is Domain:Bus:Device.Function and is the same as
+		found in /sys/bus/pci/devices/.  For example:
+		# echo 0000:00:19.0 > /sys/bus/pci/drivers/foo/bind
+		(Note: kernels before 2.6.28 may require echo -n).
+
+What:		/sys/bus/pci/drivers/.../unbind
+Date:		December 2003
+Contact:	linux-pci@vger.kernel.org
+Description:
+		Writing a device location to this file will cause the
+		driver to attempt to unbind from the device found at
+		this location.	This may be useful when overriding default
+		bindings.  The format for the location is: DDDD:BB:DD.F.
+		That is Domain:Bus:Device.Function and is the same as
+		found in /sys/bus/pci/devices/. For example:
+		# echo 0000:00:19.0 > /sys/bus/pci/drivers/foo/unbind
+		(Note: kernels before 2.6.28 may require echo -n).
+
+What:		/sys/bus/pci/drivers/.../new_id
+Date:		December 2003
+Contact:	linux-pci@vger.kernel.org
+Description:
+		Writing a device ID to this file will attempt to
+		dynamically add a new device ID to a PCI device driver.
+		This may allow the driver to support more hardware than
+		was included in the driver's static device ID support
+		table at compile time.  The format for the device ID is:
+		VVVV DDDD SVVV SDDD CCCC MMMM PPPP.  That is Vendor ID,
+		Device ID, Subsystem Vendor ID, Subsystem Device ID,
+		Class, Class Mask, and Private Driver Data.  The Vendor ID
+		and Device ID fields are required, the rest are optional.
+		Upon successfully adding an ID, the driver will probe
+		for the device and attempt to bind to it.  For example:
+		# echo "8086 10f5" > /sys/bus/pci/drivers/foo/new_id
+
 What:		/sys/bus/pci/devices/.../vpd
 Date:		February 2008
 Contact:	Ben Hutchings <bhutchings@solarflare.com>

Documentation/ABI/testing/sysfs-firmware-memmap

@@ -1,6 +1,6 @@
 What:		/sys/firmware/memmap/
 Date:		June 2008
-Contact:	Bernhard Walle <bwalle@suse.de>
+Contact:	Bernhard Walle <bernhard.walle@gmx.de>
 Description:
 		On all platforms, the firmware provides a memory map which the
 		kernel reads. The resources from that memory map are registered

Documentation/DocBook/Makefile

@@ -6,7 +6,7 @@
 # To add a new book the only step required is to add the book to the
 # list of DOCBOOKS.
 
-DOCBOOKS := z8530book.xml mcabook.xml \
+DOCBOOKS := z8530book.xml mcabook.xml device-drivers.xml \
 	    kernel-hacking.xml kernel-locking.xml deviceiobook.xml \
 	    procfs-guide.xml writing_usb_driver.xml networking.xml \
 	    kernel-api.xml filesystems.xml lsm.xml usb.xml kgdb.xml \

Documentation/DocBook/device-drivers.tmpl

@@ -0,0 +1,418 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.1.2//EN"
+	"http://www.oasis-open.org/docbook/xml/4.1.2/docbookx.dtd" []>
+
+<book id="LinuxDriversAPI">
+ <bookinfo>
+  <title>Linux Device Drivers</title>
+
+  <legalnotice>
+   <para>
+     This documentation is free software; you can redistribute
+     it and/or modify it under the terms of the GNU General Public
+     License as published by the Free Software Foundation; either
+     version 2 of the License, or (at your option) any later
+     version.
+   </para>
+
+   <para>
+     This program is distributed in the hope that it will be
+     useful, but WITHOUT ANY WARRANTY; without even the implied
+     warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+     See the GNU General Public License for more details.
+   </para>
+
+   <para>
+     You should have received a copy of the GNU General Public
+     License along with this program; if not, write to the Free
+     Software Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+     MA 02111-1307 USA
+   </para>
+
+   <para>
+     For more details see the file COPYING in the source
+     distribution of Linux.
+   </para>
+  </legalnotice>
+ </bookinfo>
+
+<toc></toc>
+
+  <chapter id="Basics">
+     <title>Driver Basics</title>
+     <sect1><title>Driver Entry and Exit points</title>
+!Iinclude/linux/init.h
+     </sect1>
+
+     <sect1><title>Atomic and pointer manipulation</title>
+!Iarch/x86/include/asm/atomic_32.h
+!Iarch/x86/include/asm/unaligned.h
+     </sect1>
+
+     <sect1><title>Delaying, scheduling, and timer routines</title>
+!Iinclude/linux/sched.h
+!Ekernel/sched.c
+!Ekernel/timer.c
+     </sect1>
+     <sect1><title>High-resolution timers</title>
+!Iinclude/linux/ktime.h
+!Iinclude/linux/hrtimer.h
+!Ekernel/hrtimer.c
+     </sect1>
+     <sect1><title>Workqueues and Kevents</title>
+!Ekernel/workqueue.c
+     </sect1>
+     <sect1><title>Internal Functions</title>
+!Ikernel/exit.c
+!Ikernel/signal.c
+!Iinclude/linux/kthread.h
+!Ekernel/kthread.c
+     </sect1>
+
+     <sect1><title>Kernel objects manipulation</title>
+<!--
+X!Iinclude/linux/kobject.h
+-->
+!Elib/kobject.c
+     </sect1>
+
+     <sect1><title>Kernel utility functions</title>
+!Iinclude/linux/kernel.h
+!Ekernel/printk.c
+!Ekernel/panic.c
+!Ekernel/sys.c
+!Ekernel/rcupdate.c
+     </sect1>
+
+     <sect1><title>Device Resource Management</title>
+!Edrivers/base/devres.c
+     </sect1>
+
+  </chapter>
+
+  <chapter id="devdrivers">
+     <title>Device drivers infrastructure</title>
+     <sect1><title>Device Drivers Base</title>
+<!--
+X!Iinclude/linux/device.h
+-->
+!Edrivers/base/driver.c
+!Edrivers/base/core.c
+!Edrivers/base/class.c
+!Edrivers/base/firmware_class.c
+!Edrivers/base/transport_class.c
+<!-- Cannot be included, because
+     attribute_container_add_class_device_adapter
+ and attribute_container_classdev_to_container
+     exceed allowed 44 characters maximum
+X!Edrivers/base/attribute_container.c
+-->
+!Edrivers/base/sys.c
+<!--
+X!Edrivers/base/interface.c
+-->
+!Edrivers/base/platform.c
+!Edrivers/base/bus.c
+     </sect1>
+     <sect1><title>Device Drivers Power Management</title>
+!Edrivers/base/power/main.c
+     </sect1>
+     <sect1><title>Device Drivers ACPI Support</title>
+<!-- Internal functions only
+X!Edrivers/acpi/sleep/main.c
+X!Edrivers/acpi/sleep/wakeup.c
+X!Edrivers/acpi/motherboard.c
+X!Edrivers/acpi/bus.c
+-->
+!Edrivers/acpi/scan.c
+!Idrivers/acpi/scan.c
+<!-- No correct structured comments
+X!Edrivers/acpi/pci_bind.c
+-->
+     </sect1>
+     <sect1><title>Device drivers PnP support</title>
+!Idrivers/pnp/core.c
+<!-- No correct structured comments
+X!Edrivers/pnp/system.c
+ -->
+!Edrivers/pnp/card.c
+!Idrivers/pnp/driver.c
+!Edrivers/pnp/manager.c
+!Edrivers/pnp/support.c
+     </sect1>
+     <sect1><title>Userspace IO devices</title>
+!Edrivers/uio/uio.c
+!Iinclude/linux/uio_driver.h
+     </sect1>
+  </chapter>
+
+  <chapter id="parportdev">
+     <title>Parallel Port Devices</title>
+!Iinclude/linux/parport.h
+!Edrivers/parport/ieee1284.c
+!Edrivers/parport/share.c
+!Idrivers/parport/daisy.c
+  </chapter>
+
+  <chapter id="message_devices">
+	<title>Message-based devices</title>
+     <sect1><title>Fusion message devices</title>
+!Edrivers/message/fusion/mptbase.c
+!Idrivers/message/fusion/mptbase.c
+!Edrivers/message/fusion/mptscsih.c
+!Idrivers/message/fusion/mptscsih.c
+!Idrivers/message/fusion/mptctl.c
+!Idrivers/message/fusion/mptspi.c
+!Idrivers/message/fusion/mptfc.c
+!Idrivers/message/fusion/mptlan.c
+     </sect1>
+     <sect1><title>I2O message devices</title>
+!Iinclude/linux/i2o.h
+!Idrivers/message/i2o/core.h
+!Edrivers/message/i2o/iop.c
+!Idrivers/message/i2o/iop.c
+!Idrivers/message/i2o/config-osm.c
+!Edrivers/message/i2o/exec-osm.c
+!Idrivers/message/i2o/exec-osm.c
+!Idrivers/message/i2o/bus-osm.c
+!Edrivers/message/i2o/device.c
+!Idrivers/message/i2o/device.c
+!Idrivers/message/i2o/driver.c
+!Idrivers/message/i2o/pci.c
+!Idrivers/message/i2o/i2o_block.c
+!Idrivers/message/i2o/i2o_scsi.c
+!Idrivers/message/i2o/i2o_proc.c
+     </sect1>
+  </chapter>
+
+  <chapter id="snddev">
+     <title>Sound Devices</title>
+!Iinclude/sound/core.h
+!Esound/sound_core.c
+!Iinclude/sound/pcm.h
+!Esound/core/pcm.c
+!Esound/core/device.c
+!Esound/core/info.c
+!Esound/core/rawmidi.c
+!Esound/core/sound.c
+!Esound/core/memory.c
+!Esound/core/pcm_memory.c
+!Esound/core/init.c
+!Esound/core/isadma.c
+!Esound/core/control.c
+!Esound/core/pcm_lib.c
+!Esound/core/hwdep.c
+!Esound/core/pcm_native.c
+!Esound/core/memalloc.c
+<!-- FIXME: Removed for now since no structured comments in source
+X!Isound/sound_firmware.c
+-->
+  </chapter>
+
+  <chapter id="uart16x50">
+     <title>16x50 UART Driver</title>
+!Iinclude/linux/serial_core.h
+!Edrivers/serial/serial_core.c
+!Edrivers/serial/8250.c
+  </chapter>
+
+  <chapter id="fbdev">
+     <title>Frame Buffer Library</title>
+
+     <para>
+       The frame buffer drivers depend heavily on four data structures.
+       These structures are declared in include/linux/fb.h.  They are
+       fb_info, fb_var_screeninfo, fb_fix_screeninfo and fb_monospecs.
+       The last three can be made available to and from userland.
+     </para>
+
+     <para>
+       fb_info defines the current state of a particular video card.
+       Inside fb_info, there exists a fb_ops structure which is a
+       collection of needed functions to make fbdev and fbcon work.
+       fb_info is only visible to the kernel.
+     </para>
+
+     <para>
+       fb_var_screeninfo is used to describe the features of a video card
+       that are user defined.  With fb_var_screeninfo, things such as
+       depth and the resolution may be defined.
+     </para>
+
+     <para>
+       The next structure is fb_fix_screeninfo. This defines the
+       properties of a card that are created when a mode is set and can't
+       be changed otherwise.  A good example of this is the start of the
+       frame buffer memory.  This "locks" the address of the frame buffer
+       memory, so that it cannot be changed or moved.
+     </para>
+
+     <para>
+       The last structure is fb_monospecs. In the old API, there was
+       little importance for fb_monospecs. This allowed for forbidden things
+       such as setting a mode of 800x600 on a fix frequency monitor. With
+       the new API, fb_monospecs prevents such things, and if used
+       correctly, can prevent a monitor from being cooked.  fb_monospecs
+       will not be useful until kernels 2.5.x.
+     </para>
+
+     <sect1><title>Frame Buffer Memory</title>
+!Edrivers/video/fbmem.c
+     </sect1>
+<!--
+     <sect1><title>Frame Buffer Console</title>
+X!Edrivers/video/console/fbcon.c
+     </sect1>
+-->
+     <sect1><title>Frame Buffer Colormap</title>
+!Edrivers/video/fbcmap.c
+     </sect1>
+<!-- FIXME:
+  drivers/video/fbgen.c has no docs, which stuffs up the sgml.  Comment
+  out until somebody adds docs.  KAO
+     <sect1><title>Frame Buffer Generic Functions</title>
+X!Idrivers/video/fbgen.c
+     </sect1>
+KAO -->
+     <sect1><title>Frame Buffer Video Mode Database</title>
+!Idrivers/video/modedb.c
+!Edrivers/video/modedb.c
+     </sect1>
+     <sect1><title>Frame Buffer Macintosh Video Mode Database</title>
+!Edrivers/video/macmodes.c
+     </sect1>
+     <sect1><title>Frame Buffer Fonts</title>
+        <para>
+           Refer to the file drivers/video/console/fonts.c for more information.
+        </para>
+<!-- FIXME: Removed for now since no structured comments in source
+X!Idrivers/video/console/fonts.c
+-->
+     </sect1>
+  </chapter>
+
+  <chapter id="input_subsystem">
+     <title>Input Subsystem</title>
+!Iinclude/linux/input.h
+!Edrivers/input/input.c
+!Edrivers/input/ff-core.c
+!Edrivers/input/ff-memless.c
+  </chapter>
+
+  <chapter id="spi">
+      <title>Serial Peripheral Interface (SPI)</title>
+  <para>
+	SPI is the "Serial Peripheral Interface", widely used with
+	embedded systems because it is a simple and efficient
+	interface:  basically a multiplexed shift register.
+	Its three signal wires hold a clock (SCK, often in the range
+	of 1-20 MHz), a "Master Out, Slave In" (MOSI) data line, and
+	a "Master In, Slave Out" (MISO) data line.
+	SPI is a full duplex protocol; for each bit shifted out the
+	MOSI line (one per clock) another is shifted in on the MISO line.
+	Those bits are assembled into words of various sizes on the
+	way to and from system memory.
+	An additional chipselect line is usually active-low (nCS);
+	four signals are normally used for each peripheral, plus
+	sometimes an interrupt.
+  </para>
+  <para>
+	The SPI bus facilities listed here provide a generalized
+	interface to declare SPI busses and devices, manage them
+	according to the standard Linux driver model, and perform
+	input/output operations.
+	At this time, only "master" side interfaces are supported,
+	where Linux talks to SPI peripherals and does not implement
+	such a peripheral itself.
+	(Interfaces to support implementing SPI slaves would
+	necessarily look different.)
+  </para>
+  <para>
+	The programming interface is structured around two kinds of driver,
+	and two kinds of device.
+	A "Controller Driver" abstracts the controller hardware, which may
+	be as simple as a set of GPIO pins or as complex as a pair of FIFOs
+	connected to dual DMA engines on the other side of the SPI shift
+	register (maximizing throughput).  Such drivers bridge between
+	whatever bus they sit on (often the platform bus) and SPI, and
+	expose the SPI side of their device as a
+	<structname>struct spi_master</structname>.
+	SPI devices are children of that master, represented as a
+	<structname>struct spi_device</structname> and manufactured from
+	<structname>struct spi_board_info</structname> descriptors which
+	are usually provided by board-specific initialization code.
+	A <structname>struct spi_driver</structname> is called a
+	"Protocol Driver", and is bound to a spi_device using normal
+	driver model calls.
+  </para>
+  <para>
+	The I/O model is a set of queued messages.  Protocol drivers
+	submit one or more <structname>struct spi_message</structname>
+	objects, which are processed and completed asynchronously.
+	(There are synchronous wrappers, however.)  Messages are
+	built from one or more <structname>struct spi_transfer</structname>
+	objects, each of which wraps a full duplex SPI transfer.
+	A variety of protocol tweaking options are needed, because
+	different chips adopt very different policies for how they
+	use the bits transferred with SPI.
+  </para>
+!Iinclude/linux/spi/spi.h
+!Fdrivers/spi/spi.c spi_register_board_info
+!Edrivers/spi/spi.c
+  </chapter>
+
+  <chapter id="i2c">
+     <title>I<superscript>2</superscript>C and SMBus Subsystem</title>
+
+     <para>
+	I<superscript>2</superscript>C (or without fancy typography, "I2C")
+	is an acronym for the "Inter-IC" bus, a simple bus protocol which is
+	widely used where low data rate communications suffice.
+	Since it's also a licensed trademark, some vendors use another
+	name (such as "Two-Wire Interface", TWI) for the same bus.
+	I2C only needs two signals (SCL for clock, SDA for data), conserving
+	board real estate and minimizing signal quality issues.
+	Most I2C devices use seven bit addresses, and bus speeds of up
+	to 400 kHz; there's a high speed extension (3.4 MHz) that's not yet
+	found wide use.
+	I2C is a multi-master bus; open drain signaling is used to
+	arbitrate between masters, as well as to handshake and to
+	synchronize clocks from slower clients.
+     </para>
+
+     <para>
+	The Linux I2C programming interfaces support only the master
+	side of bus interactions, not the slave side.
+	The programming interface is structured around two kinds of driver,
+	and two kinds of device.
+	An I2C "Adapter Driver" abstracts the controller hardware; it binds
+	to a physical device (perhaps a PCI device or platform_device) and
+	exposes a <structname>struct i2c_adapter</structname> representing
+	each I2C bus segment it manages.
+	On each I2C bus segment will be I2C devices represented by a
+	<structname>struct i2c_client</structname>.  Those devices will
+	be bound to a <structname>struct i2c_driver</structname>,
+	which should follow the standard Linux driver model.
+	(At this writing, a legacy model is more widely used.)
+	There are functions to perform various I2C protocol operations; at
+	this writing all such functions are usable only from task context.
+     </para>
+
+     <para>
+	The System Management Bus (SMBus) is a sibling protocol.  Most SMBus
+	systems are also I2C conformant.  The electrical constraints are
+	tighter for SMBus, and it standardizes particular protocol messages
+	and idioms.  Controllers that support I2C can also support most
+	SMBus operations, but SMBus controllers don't support all the protocol
+	options that an I2C controller will.
+	There are functions to perform various SMBus protocol operations,
+	either using I2C primitives or by issuing SMBus commands to
+	i2c_adapter devices which don't support those I2C operations.
+     </para>
+
+!Iinclude/linux/i2c.h
+!Fdrivers/i2c/i2c-boardinfo.c i2c_register_board_info
+!Edrivers/i2c/i2c-core.c
+  </chapter>
+
+</book>

Documentation/DocBook/kernel-api.tmpl

@@ -38,58 +38,6 @@
 
 <toc></toc>
 
-  <chapter id="Basics">
-     <title>Driver Basics</title>
-     <sect1><title>Driver Entry and Exit points</title>
-!Iinclude/linux/init.h
-     </sect1>
-
-     <sect1><title>Atomic and pointer manipulation</title>
-!Iarch/x86/include/asm/atomic_32.h
-!Iarch/x86/include/asm/unaligned.h
-     </sect1>
-
-     <sect1><title>Delaying, scheduling, and timer routines</title>
-!Iinclude/linux/sched.h
-!Ekernel/sched.c
-!Ekernel/timer.c
-     </sect1>
-     <sect1><title>High-resolution timers</title>
-!Iinclude/linux/ktime.h
-!Iinclude/linux/hrtimer.h
-!Ekernel/hrtimer.c
-     </sect1>
-     <sect1><title>Workqueues and Kevents</title>
-!Ekernel/workqueue.c
-     </sect1>
-     <sect1><title>Internal Functions</title>
-!Ikernel/exit.c
-!Ikernel/signal.c
-!Iinclude/linux/kthread.h
-!Ekernel/kthread.c
-     </sect1>
-
-     <sect1><title>Kernel objects manipulation</title>
-<!--
-X!Iinclude/linux/kobject.h
--->
-!Elib/kobject.c
-     </sect1>
-
-     <sect1><title>Kernel utility functions</title>
-!Iinclude/linux/kernel.h
-!Ekernel/printk.c
-!Ekernel/panic.c
-!Ekernel/sys.c
-!Ekernel/rcupdate.c
-     </sect1>
-
-     <sect1><title>Device Resource Management</title>
-!Edrivers/base/devres.c
-     </sect1>
-
-  </chapter>
-
   <chapter id="adt">
      <title>Data Types</title>
      <sect1><title>Doubly Linked Lists</title>
@@ -298,62 +246,6 @@ X!Earch/x86/kernel/mca_32.c
 !Ikernel/acct.c
   </chapter>
 
-  <chapter id="devdrivers">
-     <title>Device drivers infrastructure</title>
-     <sect1><title>Device Drivers Base</title>
-<!--
-X!Iinclude/linux/device.h
--->
-!Edrivers/base/driver.c
-!Edrivers/base/core.c
-!Edrivers/base/class.c
-!Edrivers/base/firmware_class.c
-!Edrivers/base/transport_class.c
-<!-- Cannot be included, because
-     attribute_container_add_class_device_adapter
- and attribute_container_classdev_to_container
-     exceed allowed 44 characters maximum
-X!Edrivers/base/attribute_container.c
--->
-!Edrivers/base/sys.c
-<!--
-X!Edrivers/base/interface.c
--->
-!Edrivers/base/platform.c
-!Edrivers/base/bus.c
-     </sect1>
-     <sect1><title>Device Drivers Power Management</title>
-!Edrivers/base/power/main.c
-     </sect1>
-     <sect1><title>Device Drivers ACPI Support</title>
-<!-- Internal functions only
-X!Edrivers/acpi/sleep/main.c
-X!Edrivers/acpi/sleep/wakeup.c
-X!Edrivers/acpi/motherboard.c
-X!Edrivers/acpi/bus.c
--->
-!Edrivers/acpi/scan.c
-!Idrivers/acpi/scan.c
-<!-- No correct structured comments
-X!Edrivers/acpi/pci_bind.c
--->
-     </sect1>
-     <sect1><title>Device drivers PnP support</title>
-!Idrivers/pnp/core.c
-<!-- No correct structured comments
-X!Edrivers/pnp/system.c
- -->
-!Edrivers/pnp/card.c
-!Idrivers/pnp/driver.c
-!Edrivers/pnp/manager.c
-!Edrivers/pnp/support.c
-     </sect1>
-     <sect1><title>Userspace IO devices</title>
-!Edrivers/uio/uio.c
-!Iinclude/linux/uio_driver.h
-     </sect1>
-  </chapter>
-
   <chapter id="blkdev">
      <title>Block Devices</title>
 !Eblock/blk-core.c
@@ -381,275 +273,6 @@ X!Edrivers/pnp/system.c
 !Edrivers/char/misc.c
   </chapter>
 
-  <chapter id="parportdev">
-     <title>Parallel Port Devices</title>
-!Iinclude/linux/parport.h
-!Edrivers/parport/ieee1284.c
-!Edrivers/parport/share.c
-!Idrivers/parport/daisy.c
-  </chapter>
-
-  <chapter id="message_devices">
-	<title>Message-based devices</title>
-     <sect1><title>Fusion message devices</title>
-!Edrivers/message/fusion/mptbase.c
-!Idrivers/message/fusion/mptbase.c
-!Edrivers/message/fusion/mptscsih.c
-!Idrivers/message/fusion/mptscsih.c
-!Idrivers/message/fusion/mptctl.c
-!Idrivers/message/fusion/mptspi.c
-!Idrivers/message/fusion/mptfc.c
-!Idrivers/message/fusion/mptlan.c
-     </sect1>
-     <sect1><title>I2O message devices</title>
-!Iinclude/linux/i2o.h
-!Idrivers/message/i2o/core.h
-!Edrivers/message/i2o/iop.c
-!Idrivers/message/i2o/iop.c
-!Idrivers/message/i2o/config-osm.c
-!Edrivers/message/i2o/exec-osm.c
-!Idrivers/message/i2o/exec-osm.c
-!Idrivers/message/i2o/bus-osm.c
-!Edrivers/message/i2o/device.c
-!Idrivers/message/i2o/device.c
-!Idrivers/message/i2o/driver.c
-!Idrivers/message/i2o/pci.c
-!Idrivers/message/i2o/i2o_block.c
-!Idrivers/message/i2o/i2o_scsi.c
-!Idrivers/message/i2o/i2o_proc.c
-     </sect1>
-  </chapter>
-
-  <chapter id="snddev">
-     <title>Sound Devices</title>
-!Iinclude/sound/core.h
-!Esound/sound_core.c
-!Iinclude/sound/pcm.h
-!Esound/core/pcm.c
-!Esound/core/device.c
-!Esound/core/info.c
-!Esound/core/rawmidi.c
-!Esound/core/sound.c
-!Esound/core/memory.c
-!Esound/core/pcm_memory.c
-!Esound/core/init.c
-!Esound/core/isadma.c
-!Esound/core/control.c
-!Esound/core/pcm_lib.c
-!Esound/core/hwdep.c
-!Esound/core/pcm_native.c
-!Esound/core/memalloc.c
-<!-- FIXME: Removed for now since no structured comments in source
-X!Isound/sound_firmware.c
--->
-  </chapter>
-
-  <chapter id="uart16x50">
-     <title>16x50 UART Driver</title>
-!Iinclude/linux/serial_core.h
-!Edrivers/serial/serial_core.c
-!Edrivers/serial/8250.c
-  </chapter>
-
-  <chapter id="fbdev">
-     <title>Frame Buffer Library</title>
-
-     <para>
-       The frame buffer drivers depend heavily on four data structures.  
-       These structures are declared in include/linux/fb.h.  They are 
-       fb_info, fb_var_screeninfo, fb_fix_screeninfo and fb_monospecs. 
-       The last three can be made available to and from userland. 
-     </para>
-
-     <para>
-       fb_info defines the current state of a particular video card. 
-       Inside fb_info, there exists a fb_ops structure which is a 
-       collection of needed functions to make fbdev and fbcon work.
-       fb_info is only visible to the kernel.
-     </para>
-
-     <para>
-       fb_var_screeninfo is used to describe the features of a video card 
-       that are user defined.  With fb_var_screeninfo, things such as
-       depth and the resolution may be defined.
-     </para>
-
-     <para>
-       The next structure is fb_fix_screeninfo. This defines the 
-       properties of a card that are created when a mode is set and can't 
-       be changed otherwise.  A good example of this is the start of the 
-       frame buffer memory.  This "locks" the address of the frame buffer
-       memory, so that it cannot be changed or moved.
-     </para>
-
-     <para>
-       The last structure is fb_monospecs. In the old API, there was 
-       little importance for fb_monospecs. This allowed for forbidden things 
-       such as setting a mode of 800x600 on a fix frequency monitor. With 
-       the new API, fb_monospecs prevents such things, and if used 
-       correctly, can prevent a monitor from being cooked.  fb_monospecs
-       will not be useful until kernels 2.5.x.
-     </para>
-
-     <sect1><title>Frame Buffer Memory</title>
-!Edrivers/video/fbmem.c
-     </sect1>
-<!--
-     <sect1><title>Frame Buffer Console</title>
-X!Edrivers/video/console/fbcon.c
-     </sect1>
--->
-     <sect1><title>Frame Buffer Colormap</title>
-!Edrivers/video/fbcmap.c
-     </sect1>
-<!-- FIXME:
-  drivers/video/fbgen.c has no docs, which stuffs up the sgml.  Comment
-  out until somebody adds docs.  KAO
-     <sect1><title>Frame Buffer Generic Functions</title>
-X!Idrivers/video/fbgen.c
-     </sect1>
-KAO -->
-     <sect1><title>Frame Buffer Video Mode Database</title>
-!Idrivers/video/modedb.c
-!Edrivers/video/modedb.c
-     </sect1>
-     <sect1><title>Frame Buffer Macintosh Video Mode Database</title>
-!Edrivers/video/macmodes.c
-     </sect1>
-     <sect1><title>Frame Buffer Fonts</title>
-        <para>
-           Refer to the file drivers/video/console/fonts.c for more information.
-        </para>
-<!-- FIXME: Removed for now since no structured comments in source
-X!Idrivers/video/console/fonts.c
--->
-     </sect1>
-  </chapter>
-
-  <chapter id="input_subsystem">
-     <title>Input Subsystem</title>
-!Iinclude/linux/input.h
-!Edrivers/input/input.c
-!Edrivers/input/ff-core.c
-!Edrivers/input/ff-memless.c
-  </chapter>
-
-  <chapter id="spi">
-      <title>Serial Peripheral Interface (SPI)</title>
-  <para>
-	SPI is the "Serial Peripheral Interface", widely used with
-	embedded systems because it is a simple and efficient
-	interface:  basically a multiplexed shift register.
-	Its three signal wires hold a clock (SCK, often in the range
-	of 1-20 MHz), a "Master Out, Slave In" (MOSI) data line, and
-	a "Master In, Slave Out" (MISO) data line.
-	SPI is a full duplex protocol; for each bit shifted out the
-	MOSI line (one per clock) another is shifted in on the MISO line.
-	Those bits are assembled into words of various sizes on the
-	way to and from system memory.
-	An additional chipselect line is usually active-low (nCS);
-	four signals are normally used for each peripheral, plus
-	sometimes an interrupt.
-  </para>
-  <para>
-	The SPI bus facilities listed here provide a generalized
-	interface to declare SPI busses and devices, manage them
-	according to the standard Linux driver model, and perform
-	input/output operations.
-	At this time, only "master" side interfaces are supported,
-	where Linux talks to SPI peripherals and does not implement
-	such a peripheral itself.
-	(Interfaces to support implementing SPI slaves would
-	necessarily look different.)
-  </para>
-  <para>
-	The programming interface is structured around two kinds of driver,
-	and two kinds of device.
-	A "Controller Driver" abstracts the controller hardware, which may
-	be as simple as a set of GPIO pins or as complex as a pair of FIFOs
-	connected to dual DMA engines on the other side of the SPI shift
-	register (maximizing throughput).  Such drivers bridge between
-	whatever bus they sit on (often the platform bus) and SPI, and
-	expose the SPI side of their device as a
-	<structname>struct spi_master</structname>.
-	SPI devices are children of that master, represented as a
-	<structname>struct spi_device</structname> and manufactured from
-	<structname>struct spi_board_info</structname> descriptors which
-	are usually provided by board-specific initialization code.
-	A <structname>struct spi_driver</structname> is called a
-	"Protocol Driver", and is bound to a spi_device using normal
-	driver model calls.
-  </para>
-  <para>
-	The I/O model is a set of queued messages.  Protocol drivers
-	submit one or more <structname>struct spi_message</structname>
-	objects, which are processed and completed asynchronously.
-	(There are synchronous wrappers, however.)  Messages are
-	built from one or more <structname>struct spi_transfer</structname>
-	objects, each of which wraps a full duplex SPI transfer.
-	A variety of protocol tweaking options are needed, because
-	different chips adopt very different policies for how they
-	use the bits transferred with SPI.
-  </para>
-!Iinclude/linux/spi/spi.h
-!Fdrivers/spi/spi.c spi_register_board_info
-!Edrivers/spi/spi.c
-  </chapter>
-
-  <chapter id="i2c">
-     <title>I<superscript>2</superscript>C and SMBus Subsystem</title>
-
-     <para>
-	I<superscript>2</superscript>C (or without fancy typography, "I2C")
-	is an acronym for the "Inter-IC" bus, a simple bus protocol which is
-	widely used where low data rate communications suffice.
-	Since it's also a licensed trademark, some vendors use another
-	name (such as "Two-Wire Interface", TWI) for the same bus.
-	I2C only needs two signals (SCL for clock, SDA for data), conserving
-	board real estate and minimizing signal quality issues.
-	Most I2C devices use seven bit addresses, and bus speeds of up
-	to 400 kHz; there's a high speed extension (3.4 MHz) that's not yet
-	found wide use.
-	I2C is a multi-master bus; open drain signaling is used to
-	arbitrate between masters, as well as to handshake and to
-	synchronize clocks from slower clients.
-     </para>
-
-     <para>
-	The Linux I2C programming interfaces support only the master
-	side of bus interactions, not the slave side.
-	The programming interface is structured around two kinds of driver,
-	and two kinds of device.
-	An I2C "Adapter Driver" abstracts the controller hardware; it binds
-	to a physical device (perhaps a PCI device or platform_device) and
-	exposes a <structname>struct i2c_adapter</structname> representing
-	each I2C bus segment it manages.
-	On each I2C bus segment will be I2C devices represented by a
-	<structname>struct i2c_client</structname>.  Those devices will
-	be bound to a <structname>struct i2c_driver</structname>,
-	which should follow the standard Linux driver model.
-	(At this writing, a legacy model is more widely used.)
-	There are functions to perform various I2C protocol operations; at
-	this writing all such functions are usable only from task context.
-     </para>
-
-     <para>
-	The System Management Bus (SMBus) is a sibling protocol.  Most SMBus
-	systems are also I2C conformant.  The electrical constraints are
-	tighter for SMBus, and it standardizes particular protocol messages
-	and idioms.  Controllers that support I2C can also support most
-	SMBus operations, but SMBus controllers don't support all the protocol
-	options that an I2C controller will.
-	There are functions to perform various SMBus protocol operations,
-	either using I2C primitives or by issuing SMBus commands to
-	i2c_adapter devices which don't support those I2C operations.
-     </para>
-
-!Iinclude/linux/i2c.h
-!Fdrivers/i2c/i2c-boardinfo.c i2c_register_board_info
-!Edrivers/i2c/i2c-core.c
-  </chapter>
-
   <chapter id="clk">
      <title>Clock Framework</title>
 

Documentation/cgroups/cgroups.txt

@@ -252,10 +252,8 @@ cgroup file system directories.
 When a task is moved from one cgroup to another, it gets a new
 css_set pointer - if there's an already existing css_set with the
 desired collection of cgroups then that group is reused, else a new
-css_set is allocated. Note that the current implementation uses a
-linear search to locate an appropriate existing css_set, so isn't
-very efficient. A future version will use a hash table for better
-performance.
+css_set is allocated. The appropriate existing css_set is located by
+looking into a hash table.
 
 To allow access from a cgroup to the css_sets (and hence tasks)
 that comprise it, a set of cg_cgroup_link objects form a lattice;

Documentation/cgroups/cpusets.txt

@@ -142,7 +142,7 @@ into the rest of the kernel, none in performance critical paths:
  - in fork and exit, to attach and detach a task from its cpuset.
  - in sched_setaffinity, to mask the requested CPUs by what's
    allowed in that tasks cpuset.
- - in sched.c migrate_all_tasks(), to keep migrating tasks within
+ - in sched.c migrate_live_tasks(), to keep migrating tasks within
    the CPUs allowed by their cpuset, if possible.
  - in the mbind and set_mempolicy system calls, to mask the requested
    Memory Nodes by what's allowed in that tasks cpuset.
@@ -175,6 +175,10 @@ files describing that cpuset:
  - mem_exclusive flag: is memory placement exclusive?
  - mem_hardwall flag:  is memory allocation hardwalled
  - memory_pressure: measure of how much paging pressure in cpuset
+ - memory_spread_page flag: if set, spread page cache evenly on allowed nodes
+ - memory_spread_slab flag: if set, spread slab cache evenly on allowed nodes
+ - sched_load_balance flag: if set, load balance within CPUs on that cpuset
+ - sched_relax_domain_level: the searching range when migrating tasks
 
 In addition, the root cpuset only has the following file:
  - memory_pressure_enabled flag: compute memory_pressure?
@@ -252,7 +256,7 @@ is causing.
 
 This is useful both on tightly managed systems running a wide mix of
 submitted jobs, which may choose to terminate or re-prioritize jobs that
-are trying to use more memory than allowed on the nodes assigned them,
+are trying to use more memory than allowed on the nodes assigned to them,
 and with tightly coupled, long running, massively parallel scientific
 computing jobs that will dramatically fail to meet required performance
 goals if they start to use more memory than allowed to them.
@@ -378,7 +382,7 @@ as cpusets and sched_setaffinity.
 The algorithmic cost of load balancing and its impact on key shared
 kernel data structures such as the task list increases more than
 linearly with the number of CPUs being balanced.  So the scheduler
-has support to  partition the systems CPUs into a number of sched
+has support to partition the systems CPUs into a number of sched
 domains such that it only load balances within each sched domain.
 Each sched domain covers some subset of the CPUs in the system;
 no two sched domains overlap; some CPUs might not be in any sched
@@ -485,17 +489,22 @@ of CPUs allowed to a cpuset having 'sched_load_balance' enabled.
 The internal kernel cpuset to scheduler interface passes from the
 cpuset code to the scheduler code a partition of the load balanced
 CPUs in the system. This partition is a set of subsets (represented
-as an array of cpumask_t) of CPUs, pairwise disjoint, that cover all
-the CPUs that must be load balanced.
-
-Whenever the 'sched_load_balance' flag changes, or CPUs come or go
-from a cpuset with this flag enabled, or a cpuset with this flag
-enabled is removed, the cpuset code builds a new such partition and
-passes it to the scheduler sched domain setup code, to have the sched
-domains rebuilt as necessary.
+as an array of struct cpumask) of CPUs, pairwise disjoint, that cover
+all the CPUs that must be load balanced.
+
+The cpuset code builds a new such partition and passes it to the
+scheduler sched domain setup code, to have the sched domains rebuilt
+as necessary, whenever:
+ - the 'sched_load_balance' flag of a cpuset with non-empty CPUs changes,
+ - or CPUs come or go from a cpuset with this flag enabled,
+ - or 'sched_relax_domain_level' value of a cpuset with non-empty CPUs
+   and with this flag enabled changes,
+ - or a cpuset with non-empty CPUs and with this flag enabled is removed,
+ - or a cpu is offlined/onlined.
 
 This partition exactly defines what sched domains the scheduler should
-setup - one sched domain for each element (cpumask_t) in the partition.
+setup - one sched domain for each element (struct cpumask) in the
+partition.
 
 The scheduler remembers the currently active sched domain partitions.
 When the scheduler routine partition_sched_domains() is invoked from
@@ -559,7 +568,7 @@ domain, the largest value among those is used.  Be careful, if one
 requests 0 and others are -1 then 0 is used.
 
 Note that modifying this file will have both good and bad effects,
-and whether it is acceptable or not will be depend on your situation.
+and whether it is acceptable or not depends on your situation.
 Don't modify this file if you are not sure.
 
 If your situation is:
@@ -600,19 +609,15 @@ to allocate a page of memory for that task.
 
 If a cpuset has its 'cpus' modified, then each task in that cpuset
 will have its allowed CPU placement changed immediately.  Similarly,
-if a tasks pid is written to a cpusets 'tasks' file, in either its
-current cpuset or another cpuset, then its allowed CPU placement is
-changed immediately.  If such a task had been bound to some subset
-of its cpuset using the sched_setaffinity() call, the task will be
-allowed to run on any CPU allowed in its new cpuset, negating the
-affect of the prior sched_setaffinity() call.
+if a tasks pid is written to another cpusets 'tasks' file, then its
+allowed CPU placement is changed immediately.  If such a task had been
+bound to some subset of its cpuset using the sched_setaffinity() call,
+the task will be allowed to run on any CPU allowed in its new cpuset,
+negating the effect of the prior sched_setaffinity() call.
 
 In summary, the memory placement of a task whose cpuset is changed is
 updated by the kernel, on the next allocation of a page for that task,
-but the processor placement is not updated, until that tasks pid is
-rewritten to the 'tasks' file of its cpuset.  This is done to avoid
-impacting the scheduler code in the kernel with a check for changes
-in a tasks processor placement.
+and the processor placement is updated immediately.
 
 Normally, once a page is allocated (given a physical page
 of main memory) then that page stays on whatever node it
@@ -681,10 +686,14 @@ and then start a subshell 'sh' in that cpuset:
   # The next line should display '/Charlie'
   cat /proc/self/cpuset
 
-In the future, a C library interface to cpusets will likely be
-available.  For now, the only way to query or modify cpusets is
-via the cpuset file system, using the various cd, mkdir, echo, cat,
-rmdir commands from the shell, or their equivalent from C.
+There are ways to query or modify cpusets:
+ - via the cpuset file system directly, using the various cd, mkdir, echo,
+   cat, rmdir commands from the shell, or their equivalent from C.
+ - via the C library libcpuset.
+ - via the C library libcgroup.
+   (http://sourceforge.net/proects/libcg/)
+ - via the python application cset.
+   (http://developer.novell.com/wiki/index.php/Cpuset)
 
 The sched_setaffinity calls can also be done at the shell prompt using
 SGI's runon or Robert Love's taskset.  The mbind and set_mempolicy
@@ -756,7 +765,7 @@ mount -t cpuset X /dev/cpuset
 
 is equivalent to
 
-mount -t cgroup -ocpuset X /dev/cpuset
+mount -t cgroup -ocpuset,noprefix X /dev/cpuset
 echo "/sbin/cpuset_release_agent" > /dev/cpuset/release_agent
 
 2.2 Adding/removing cpus

Documentation/driver-model/device.txt

@@ -127,9 +127,11 @@ void unlock_device(struct device * dev);
 Attributes
 ~~~~~~~~~~
 struct device_attribute {
-        struct attribute        attr;
-        ssize_t (*show)(struct device * dev, char * buf, size_t count, loff_t off);
-        ssize_t (*store)(struct device * dev, const char * buf, size_t count, loff_t off);
+	struct attribute	attr;
+	ssize_t (*show)(struct device *dev, struct device_attribute *attr,
+			char *buf);
+	ssize_t (*store)(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count);
 };
 
 Attributes of devices can be exported via drivers using a simple

Documentation/dvb/README.flexcop

@@ -1,205 +0,0 @@
-This README escorted the skystar2-driver rewriting procedure. It describes the
-state of the new flexcop-driver set and some internals are written down here
-too.
-
-This document hopefully describes things about the flexcop and its
-device-offsprings. Goal was to write an easy-to-write and easy-to-read set of
-drivers based on the skystar2.c and other information.
-
-Remark: flexcop-pci.c was a copy of skystar2.c, but every line has been
-touched and rewritten.
-
-History & News
-==============
-  2005-04-01 - correct USB ISOC transfers (thanks to Vadim Catana)
-
-
-
-
-General coding processing
-=========================
-
-We should proceed as follows (as long as no one complains):
-
-0) Think before start writing code!
-
-1) rewriting the skystar2.c with the help of the flexcop register descriptions
-and splitting up the files to a pci-bus-part and a flexcop-part.
-The new driver will be called b2c2-flexcop-pci.ko/b2c2-flexcop-usb.ko for the
-device-specific part and b2c2-flexcop.ko for the common flexcop-functions.
-
-2) Search for errors in the leftover of flexcop-pci.c (compare with pluto2.c
-and other pci drivers)
-
-3) make some beautification (see 'Improvements when rewriting (refactoring) is
-done')
-
-4) Testing the new driver and maybe substitute the skystar2.c with it, to reach
-a wider tester audience.
-
-5) creating an usb-bus-part using the already written flexcop code for the pci
-card.
-
-Idea: create a kernel-object for the flexcop and export all important
-functions. This option saves kernel-memory, but maybe a lot of functions have
-to be exported to kernel namespace.
-
-
-Current situation
-=================
-
-0) Done :)
-1) Done (some minor issues left)
-2) Done
-3) Not ready yet, more information is necessary
-4) next to be done (see the table below)
-5) USB driver is working (yes, there are some minor issues)
-
-What seems to be ready?
------------------------
-
-1) Rewriting
-1a) i2c is cut off from the flexcop-pci.c and seems to work
-1b) moved tuner and demod stuff from flexcop-pci.c to flexcop-tuner-fe.c
-1c) moved lnb and diseqc stuff from flexcop-pci.c to flexcop-tuner-fe.c
-1e) eeprom (reading MAC address)
-1d) sram (no dynamic sll size detection (commented out) (using default as JJ told me))
-1f) misc. register accesses for reading parameters (e.g. resetting, revision)
-1g) pid/mac filter (flexcop-hw-filter.c)
-1i) dvb-stuff initialization in flexcop.c (done)
-1h) dma stuff (now just using the size-irq, instead of all-together, to be done)
-1j) remove flexcop initialization from flexcop-pci.c completely (done)
-1l) use a well working dma IRQ method (done, see 'Known bugs and problems and TODO')
-1k) cleanup flexcop-files (remove unused EXPORT_SYMBOLs, make static from
-non-static where possible, moved code to proper places)
-
-2) Search for errors in the leftover of flexcop-pci.c (partially done)
-5a) add MAC address reading
-5c) feeding of ISOC data to the software demux (format of the isochronous data
-and speed optimization, no real error) (thanks to Vadim Catana)
-
-What to do in the near future?
---------------------------------------
-(no special order here)
-
-5) USB driver
-5b) optimize isoc-transfer (submitting/killing isoc URBs when transfer is starting)
-
-Testing changes
----------------
-
-O             = item is working
-P             = item is partially working
-X             = item is not working
-N             = item does not apply here
-<empty field> = item need to be examined
-
-       | PCI                               | USB
-item   | mt352 | nxt2002 | stv0299 | mt312 | mt352 | nxt2002 | stv0299 | mt312
--------+-------+---------+---------+-------+-------+---------+---------+-------
-1a)    | O     |         |         |       | N     | N       | N       | N
-1b)    | O     |         |         |       |       |         | O       |
-1c)    | N     | N       |         |       | N     | N       | O       |
-1d)    |                 O                 |                 O
-1e)    |                 O                 |                 O
-1f)    |                                   P
-1g)    |                                   O
-1h)    |                 P                 |
-1i)    |                 O                 |                 N
-1j)    |                 O                 |                 N
-1l)    |                 O                 |                 N
-2)     |                 O                 |                 N
-5a)    |                 N                 |                 O
-5b)*   |                 N                 |
-5c)    |                 N                 |                 O
-
-* - not done yet
-
-Known bugs and problems and TODO
---------------------------------
-
-1g/h/l) when pid filtering is enabled on the pci card
-
-DMA usage currently:
-  The DMA is splitted in 2 equal-sized subbuffers. The Flexcop writes to first
-  address and triggers an IRQ when it's full and starts writing to the second
-  address. When the second address is full, the IRQ is triggered again, and
-  the flexcop writes to first address again, and so on.
-  The buffersize of each address is currently 640*188 bytes.
-
-  Problem is, when using hw-pid-filtering and doing some low-bandwidth
-  operation (like scanning) the buffers won't be filled enough to trigger
-  the IRQ. That's why:
-
-  When PID filtering is activated, the timer IRQ is used. Every 1.97 ms the IRQ
-  is triggered.  Is the current write address of DMA1 different to the one
-  during the last IRQ, then the data is passed to the demuxer.
-
-  There is an additional DMA-IRQ-method: packet count IRQ. This isn't
-  implemented correctly yet.
-
-  The solution is to disable HW PID filtering, but I don't know how the DVB
-  API software demux behaves on slow systems with 45MBit/s TS.
-
-Solved bugs :)
---------------
-1g) pid-filtering (somehow pid index 4 and 5 (EMM_PID and ECM_PID) aren't
-working)
-SOLUTION: also index 0 was affected, because net_translation is done for
-these indexes by default
-
-5b) isochronous transfer does only work in the first attempt (for the Sky2PC
-USB, Air2PC is working) SOLUTION: the flexcop was going asleep and never really
-woke up again (don't know if this need fixes, see
-flexcop-fe-tuner.c:flexcop_sleep)
-
-NEWS: when the driver is loaded and unloaded and loaded again (w/o doing
-anything in the while the driver is loaded the first time), no transfers take
-place anymore.
-
-Improvements when rewriting (refactoring) is done
-=================================================
-
-- split sleeping of the flexcop (misc_204.ACPI3_sig = 1;) from lnb_control
-  (enable sleeping for other demods than dvb-s)
-- add support for CableStar (stv0297 Microtune 203x/ALPS) (almost done, incompatibilities with the Nexus-CA)
-
-Debugging
----------
-- add verbose debugging to skystar2.c (dump the reg_dw_data) and compare it
-  with this flexcop, this is important, because i2c is now using the
-  flexcop_ibi_value union from flexcop-reg.h (do you have a better idea for
-  that, please tell us so).
-
-Everything which is identical in the following table, can be put into a common
-flexcop-module.
-
-		  PCI                  USB
--------------------------------------------------------------------------------
-Different:
-Register access:  accessing IO memory  USB control message
-I2C bus:          I2C bus of the FC    USB control message
-Data transfer:    DMA                  isochronous transfer
-EEPROM transfer:  through i2c bus      not clear yet
-
-Identical:
-Streaming:                 accessing registers
-PID Filtering:             accessing registers
-Sram destinations:         accessing registers
-Tuner/Demod:                     I2C bus
-DVB-stuff:            can be written for common use
-
-Acknowledgements (just for the rewriting part)
-================
-
-Bjarne Steinsbo thought a lot in the first place of the pci part for this code
-sharing idea.
-
-Andreas Oberritter for providing a recent PCI initialization template
-(pluto2.c).
-
-Boleslaw Ciesielski for pointing out a problem with firmware loader.
-
-Vadim Catana for correcting the USB transfer.
-
-comments, critics and ideas to linux-dvb@linuxtv.org.

Documentation/dvb/technisat.txt

@@ -1,5 +1,5 @@
-How to set up the Technisat devices
-===================================
+How to set up the Technisat/B2C2 Flexcop devices
+================================================
 
 1) Find out what device you have
 ================================
@@ -16,54 +16,60 @@ DVB: registering frontend 0 (Conexant CX24123/CX24109)...
 
 If the Technisat is the only TV device in your box get rid of unnecessary modules and check this one:
 "Multimedia devices" => "Customise analog and hybrid tuner modules to build"
-In this directory uncheck every driver which is activated there.
+In this directory uncheck every driver which is activated there (except "Simple tuner support" for case 9 only).
 
 Then please activate:
 2a) Main module part:
 
 a.)"Multimedia devices" => "DVB/ATSC adapters" => "Technisat/B2C2 FlexcopII(b) and FlexCopIII adapters"
-b.)"Multimedia devices" => "DVB/ATSC adapters" => "Technisat/B2C2 FlexcopII(b) and FlexCopIII adapters" => "Technisat/B2C2 Air/Sky/Cable2PC PCI" in case of a PCI card OR
+b.)"Multimedia devices" => "DVB/ATSC adapters" => "Technisat/B2C2 FlexcopII(b) and FlexCopIII adapters" => "Technisat/B2C2 Air/Sky/Cable2PC PCI" in case of a PCI card
+OR
 c.)"Multimedia devices" => "DVB/ATSC adapters" => "Technisat/B2C2 FlexcopII(b) and FlexCopIII adapters" => "Technisat/B2C2 Air/Sky/Cable2PC USB" in case of an USB 1.1 adapter
 d.)"Multimedia devices" => "DVB/ATSC adapters" => "Technisat/B2C2 FlexcopII(b) and FlexCopIII adapters" => "Enable debug for the B2C2 FlexCop drivers"
 Notice: d.) is helpful for troubleshooting
 
 2b) Frontend module part:
 
-1.) Revision 2.3:
+1.) SkyStar DVB-S Revision 2.3:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "Zarlink VP310/MT312/ZL10313 based"
 
-2.) Revision 2.6:
+2.) SkyStar DVB-S Revision 2.6:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "ST STV0299 based"
 
-3.) Revision 2.7:
+3.) SkyStar DVB-S Revision 2.7:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "Samsung S5H1420 based"
 c.)"Multimedia devices" => "Customise DVB frontends" => "Integrant ITD1000 Zero IF tuner for DVB-S/DSS"
 d.)"Multimedia devices" => "Customise DVB frontends" => "ISL6421 SEC controller"
 
-4.) Revision 2.8:
+4.) SkyStar DVB-S Revision 2.8:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "Conexant CX24113/CX24128 tuner for DVB-S/DSS"
 c.)"Multimedia devices" => "Customise DVB frontends" => "Conexant CX24123 based"
 d.)"Multimedia devices" => "Customise DVB frontends" => "ISL6421 SEC controller"
 
-5.) DVB-T card:
+5.) AirStar DVB-T card:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "Zarlink MT352 based"
 
-6.) DVB-C card:
+6.) CableStar DVB-C card:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "ST STV0297 based"
 
-7.) ATSC card 1st generation:
+7.) AirStar ATSC card 1st generation:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "Broadcom BCM3510"
 
-8.) ATSC card 2nd generation:
+8.) AirStar ATSC card 2nd generation:
 a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
 b.)"Multimedia devices" => "Customise DVB frontends" => "NxtWave Communications NXT2002/NXT2004 based"
-c.)"Multimedia devices" => "Customise DVB frontends" => "LG Electronics LGDT3302/LGDT3303 based"
+c.)"Multimedia devices" => "Customise DVB frontends" => "Generic I2C PLL based tuners"
 
-Author: Uwe Bugla <uwe.bugla@gmx.de> December 2008
+9.) AirStar ATSC card 3rd generation:
+a.)"Multimedia devices" => "Customise DVB frontends" => "Customise the frontend modules to build"
+b.)"Multimedia devices" => "Customise DVB frontends" => "LG Electronics LGDT3302/LGDT3303 based"
+c.)"Multimedia devices" => "Customise analog and hybrid tuner modules to build" => "Simple tuner support"
+
+Author: Uwe Bugla <uwe.bugla@gmx.de> February 2009

Documentation/filesystems/sysfs.txt

@@ -2,8 +2,10 @@
 sysfs - _The_ filesystem for exporting kernel objects. 
 
 Patrick Mochel	<mochel@osdl.org>
+Mike Murphy <mamurph@cs.clemson.edu>
 
-10 January 2003
+Revised:    22 February 2009
+Original:   10 January 2003
 
 
 What it is:
@@ -64,12 +66,13 @@ An attribute definition is simply:
 
 struct attribute {
         char                    * name;
+        struct module		*owner;
         mode_t                  mode;
 };
 
 
-int sysfs_create_file(struct kobject * kobj, struct attribute * attr);
-void sysfs_remove_file(struct kobject * kobj, struct attribute * attr);
+int sysfs_create_file(struct kobject * kobj, const struct attribute * attr);
+void sysfs_remove_file(struct kobject * kobj, const struct attribute * attr);
 
 
 A bare attribute contains no means to read or write the value of the
@@ -80,9 +83,11 @@ a specific object type.
 For example, the driver model defines struct device_attribute like:
 
 struct device_attribute {
-        struct attribute        attr;
-        ssize_t (*show)(struct device * dev, char * buf);
-        ssize_t (*store)(struct device * dev, const char * buf);
+	struct attribute	attr;
+	ssize_t (*show)(struct device *dev, struct device_attribute *attr,
+			char *buf);
+	ssize_t (*store)(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count);
 };
 
 int device_create_file(struct device *, struct device_attribute *);
@@ -90,12 +95,8 @@ void device_remove_file(struct device *, struct device_attribute *);
 
 It also defines this helper for defining device attributes: 
 
-#define DEVICE_ATTR(_name, _mode, _show, _store)      \
-struct device_attribute dev_attr_##_name = {            \
-        .attr = {.name  = __stringify(_name) , .mode   = _mode },      \
-        .show   = _show,                                \
-        .store  = _store,                               \
-};
+#define DEVICE_ATTR(_name, _mode, _show, _store) \
+struct device_attribute dev_attr_##_name = __ATTR(_name, _mode, _show, _store)
 
 For example, declaring
 
@@ -107,9 +108,9 @@ static struct device_attribute dev_attr_foo = {
        .attr	= {
 		.name = "foo",
 		.mode = S_IWUSR | S_IRUGO,
+		.show = show_foo,
+		.store = store_foo,
 	},
-	.show = show_foo,
-	.store = store_foo,
 };
 
 
@@ -161,10 +162,12 @@ To read or write attributes, show() or store() methods must be
 specified when declaring the attribute. The method types should be as
 simple as those defined for device attributes:
 
-        ssize_t (*show)(struct device * dev, char * buf);
-        ssize_t (*store)(struct device * dev, const char * buf);
+ssize_t (*show)(struct device * dev, struct device_attribute * attr,
+                char * buf);
+ssize_t (*store)(struct device * dev, struct device_attribute * attr,
+                 const char * buf);
 
-IOW, they should take only an object and a buffer as parameters. 
+IOW, they should take only an object, an attribute, and a buffer as parameters.
 
 
 sysfs allocates a buffer of size (PAGE_SIZE) and passes it to the
@@ -299,14 +302,16 @@ The following interface layers currently exist in sysfs:
 Structure:
 
 struct device_attribute {
-        struct attribute        attr;
-        ssize_t (*show)(struct device * dev, char * buf);
-        ssize_t (*store)(struct device * dev, const char * buf);
+	struct attribute	attr;
+	ssize_t (*show)(struct device *dev, struct device_attribute *attr,
+			char *buf);
+	ssize_t (*store)(struct device *dev, struct device_attribute *attr,
+			 const char *buf, size_t count);
 };
 
 Declaring:
 
-DEVICE_ATTR(_name, _str, _mode, _show, _store);
+DEVICE_ATTR(_name, _mode, _show, _store);
 
 Creation/Removal:
 
@@ -342,7 +347,8 @@ Structure:
 struct driver_attribute {
         struct attribute        attr;
         ssize_t (*show)(struct device_driver *, char * buf);
-        ssize_t (*store)(struct device_driver *, const char * buf);
+        ssize_t (*store)(struct device_driver *, const char * buf,
+                         size_t count);
 };
 
 Declaring:

Documentation/hwmon/hpfall.c

@@ -0,0 +1,101 @@
+/* Disk protection for HP machines.
+ *
+ * Copyright 2008 Eric Piel
+ * Copyright 2009 Pavel Machek <pavel@suse.cz>
+ *
+ * GPLv2.
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <unistd.h>
+#include <fcntl.h>
+#include <sys/stat.h>
+#include <sys/types.h>
+#include <string.h>
+#include <stdint.h>
+#include <errno.h>
+#include <signal.h>
+
+void write_int(char *path, int i)
+{
+	char buf[1024];
+	int fd = open(path, O_RDWR);
+	if (fd < 0) {
+		perror("open");
+		exit(1);
+	}
+	sprintf(buf, "%d", i);
+	if (write(fd, buf, strlen(buf)) != strlen(buf)) {
+		perror("write");
+		exit(1);
+	}
+	close(fd);
+}
+
+void set_led(int on)
+{
+	write_int("/sys/class/leds/hp::hddprotect/brightness", on);
+}
+
+void protect(int seconds)
+{
+	write_int("/sys/block/sda/device/unload_heads", seconds*1000);
+}
+
+int on_ac(void)
+{
+//	/sys/class/power_supply/AC0/online
+}
+
+int lid_open(void)
+{
+//	/proc/acpi/button/lid/LID/state
+}
+
+void ignore_me(void)
+{
+	protect(0);
+	set_led(0);
+
+}
+
+int main(int argc, char* argv[])
+{
+       int fd, ret;
+
+       fd = open("/dev/freefall", O_RDONLY);
+       if (fd < 0) {
+               perror("open");
+               return EXIT_FAILURE;
+       }
+
+	signal(SIGALRM, ignore_me);
+
+       for (;;) {
+	       unsigned char count;
+
+               ret = read(fd, &count, sizeof(count));
+	       alarm(0);
+	       if ((ret == -1) && (errno == EINTR)) {
+		       /* Alarm expired, time to unpark the heads */
+		       continue;
+	       }
+
+               if (ret != sizeof(count)) {
+                       perror("read");
+                       break;
+               }
+
+	       protect(21);
+	       set_led(1);
+	       if (1 || on_ac() || lid_open()) {
+		       alarm(2);
+	       } else {
+		       alarm(20);
+	       }
+       }
+
+       close(fd);
+       return EXIT_SUCCESS;
+}

Documentation/hwmon/lis3lv02d

@@ -33,6 +33,14 @@ rate - reports the sampling rate of the accelerometer device in HZ
 This driver also provides an absolute input class device, allowing
 the laptop to act as a pinball machine-esque joystick.
 
+Another feature of the driver is misc device called "freefall" that
+acts similar to /dev/rtc and reacts on free-fall interrupts received
+from the device. It supports blocking operations, poll/select and
+fasync operation modes. You must read 1 bytes from the device.  The
+result is number of free-fall interrupts since the last successful
+read (or 255 if number of interrupts would not fit).
+
+
 Axes orientation
 ----------------
 

Documentation/kernel-parameters.txt

@@ -114,7 +114,7 @@ In addition, the following text indicates that the option:
 Parameters denoted with BOOT are actually interpreted by the boot
 loader, and have no meaning to the kernel directly.
 Do not modify the syntax of boot loader parameters without extreme
-need or coordination with <Documentation/x86/i386/boot.txt>.
+need or coordination with <Documentation/x86/boot.txt>.
 
 There are also arch-specific kernel-parameters not documented here.
 See for example <Documentation/x86/x86_64/boot-options.txt>.
@@ -134,7 +134,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	acpi=		[HW,ACPI,X86-64,i386]
 			Advanced Configuration and Power Interface
-			Format: { force | off | ht | strict | noirq }
+			Format: { force | off | ht | strict | noirq | rsdt }
 			force -- enable ACPI if default was off
 			off -- disable ACPI if default was on
 			noirq -- do not use ACPI for IRQ routing
@@ -868,8 +868,10 @@ and is between 256 and 4096 characters. It is defined in the file
 	icn=		[HW,ISDN]
 			Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
 
-	ide=		[HW] (E)IDE subsystem
-			Format: ide=nodma or ide=doubler
+	ide-core.nodma=	[HW] (E)IDE subsystem
+			Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
+			.vlb_clock .pci_clock .noflush .noprobe .nowerr .cdrom
+			.chs .ignore_cable are additional options
 			See Documentation/ide/ide.txt.
 
 	idebus=		[HW] (E)IDE subsystem - VLB/PCI bus speed
@@ -2449,7 +2451,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			See Documentation/fb/modedb.txt.
 
 	vga=		[BOOT,X86-32] Select a particular video mode
-			See Documentation/x86/i386/boot.txt and
+			See Documentation/x86/boot.txt and
 			Documentation/svga.txt.
 			Use vga=ask for menu.
 			This is actually a boot loader parameter; the value is

Documentation/scsi/cxgb3i.txt

@@ -4,7 +4,7 @@ Introduction
 ============
 
 The Chelsio T3 ASIC based Adapters (S310, S320, S302, S304, Mezz cards, etc.
-series of products) supports iSCSI acceleration and iSCSI Direct Data Placement
+series of products) support iSCSI acceleration and iSCSI Direct Data Placement
 (DDP) where the hardware handles the expensive byte touching operations, such
 as CRC computation and verification, and direct DMA to the final host memory
 destination:
@@ -31,9 +31,9 @@ destination:
 	  the TCP segments onto the wire. It handles TCP retransmission if
 	  needed.
 
-	  On receving, S3 h/w recovers the iSCSI PDU by reassembling TCP
+	  On receiving, S3 h/w recovers the iSCSI PDU by reassembling TCP
 	  segments, separating the header and data, calculating and verifying
-	  the digests, then forwards the header to the host. The payload data,
+	  the digests, then forwarding the header to the host. The payload data,
 	  if possible, will be directly placed into the pre-posted host DDP
 	  buffer. Otherwise, the payload data will be sent to the host too.
 
@@ -68,9 +68,8 @@ The following steps need to be taken to accelerates the open-iscsi initiator:
 	sure the ip address is unique in the network.
 
 3. edit /etc/iscsi/iscsid.conf
-   The default setting for MaxRecvDataSegmentLength (131072) is too big,
-   replace "node.conn[0].iscsi.MaxRecvDataSegmentLength" to be a value no
-   bigger than 15360 (for example 8192):
+   The default setting for MaxRecvDataSegmentLength (131072) is too big;
+   replace with a value no bigger than 15360 (for example 8192):
 
 	node.conn[0].iscsi.MaxRecvDataSegmentLength = 8192
 

MAINTAINERS

@@ -692,6 +692,13 @@ M:	kernel@wantstofly.org
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
+ARM/NUVOTON W90X900 ARM ARCHITECTURE
+P:      Wan ZongShun
+M:      mcuos.com@gmail.com
+L:      linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+W:      http://www.mcuos.com
+S:      Maintained
+
 ARPD SUPPORT
 P:	Jonathan Layes
 L:	netdev@vger.kernel.org
@@ -2001,7 +2008,7 @@ S:	Maintained
 
 HIBERNATION (aka Software Suspend, aka swsusp)
 P:	Pavel Machek
-M:	pavel@suse.cz
+M:	pavel@ucw.cz
 P:	Rafael J. Wysocki
 M:	rjw@sisk.pl
 L:	linux-pm@lists.linux-foundation.org
@@ -2457,7 +2464,7 @@ S:	Maintained
 
 ISDN SUBSYSTEM
 P:	Karsten Keil
-M:	kkeil@suse.de
+M:	isdn@linux-pingi.de
 L:	isdn4linux@listserv.isdn4linux.de (subscribers-only)
 W:	http://www.isdn4linux.de
 T:	git kernel.org:/pub/scm/linux/kernel/kkeil/isdn-2.6.git
@@ -3327,8 +3334,8 @@ P:	Jeremy Fitzhardinge
 M:	jeremy@xensource.com
 P:	Chris Wright
 M:	chrisw@sous-sol.org
-P:	Zachary Amsden
-M:	zach@vmware.com
+P:	Alok Kataria
+M:	akataria@vmware.com
 P:	Rusty Russell
 M:	rusty@rustcorp.com.au
 L:	virtualization@lists.osdl.org
@@ -4172,7 +4179,7 @@ SUSPEND TO RAM
 P:	Len Brown
 M:	len.brown@intel.com
 P:	Pavel Machek
-M:	pavel@suse.cz
+M:	pavel@ucw.cz
 P:	Rafael J. Wysocki
 M:	rjw@sisk.pl
 L:	linux-pm@lists.linux-foundation.org

Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 29
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc6
 NAME = Erotic Pickled Herring
 
 # *DOCUMENTATION*

README

@@ -188,7 +188,7 @@ CONFIGURING the kernel:
 			   values to random values.
 
    You can find more information on using the Linux kernel config tools
-   in Documentation/kbuild/make-configs.txt.
+   in Documentation/kbuild/kconfig.txt.
 
 	NOTES on "make config":
 	- having unnecessary drivers will make the kernel bigger, and can

arch/arm/configs/at91sam9260ek_defconfig

@@ -608,7 +608,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
 # Watchdog Device Drivers
 #
 # CONFIG_SOFT_WATCHDOG is not set
-CONFIG_AT91SAM9_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
 
 #
 # USB-based Watchdog Cards

arch/arm/configs/at91sam9261ek_defconfig

@@ -700,7 +700,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
 # Watchdog Device Drivers
 #
 # CONFIG_SOFT_WATCHDOG is not set
-CONFIG_AT91SAM9_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
 
 #
 # USB-based Watchdog Cards

arch/arm/configs/at91sam9263ek_defconfig

@@ -710,7 +710,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
 # Watchdog Device Drivers
 #
 # CONFIG_SOFT_WATCHDOG is not set
-CONFIG_AT91SAM9_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
 
 #
 # USB-based Watchdog Cards

arch/arm/configs/at91sam9rlek_defconfig

@@ -606,7 +606,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
 # Watchdog Device Drivers
 #
 # CONFIG_SOFT_WATCHDOG is not set
-CONFIG_AT91SAM9_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
 
 #
 # Sonics Silicon Backplane

arch/arm/configs/qil-a9260_defconfig

@@ -727,7 +727,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
 # Watchdog Device Drivers
 #
 # CONFIG_SOFT_WATCHDOG is not set
-# CONFIG_AT91SAM9_WATCHDOG is not set
+# CONFIG_AT91SAM9X_WATCHDOG is not set
 
 #
 # USB-based Watchdog Cards

arch/arm/kernel/elf.c

@@ -74,9 +74,9 @@ EXPORT_SYMBOL(elf_set_personality);
  */
 int arm_elf_read_implies_exec(const struct elf32_hdr *x, int executable_stack)
 {
-	if (executable_stack != EXSTACK_ENABLE_X)
+	if (executable_stack != EXSTACK_DISABLE_X)
 		return 1;
-	if (cpu_architecture() <= CPU_ARCH_ARMv6)
+	if (cpu_architecture() < CPU_ARCH_ARMv6)
 		return 1;
 	return 0;
 }

arch/arm/mach-at91/at91cap9_devices.c

@@ -697,7 +697,7 @@ static void __init at91_add_device_rtt(void)
  *  Watchdog
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
+#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
 static struct platform_device at91cap9_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,

arch/arm/mach-at91/at91sam9260_devices.c

@@ -643,7 +643,7 @@ static void __init at91_add_device_rtt(void)
  *  Watchdog
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
+#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
 static struct platform_device at91sam9260_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,

arch/arm/mach-at91/at91sam9261_devices.c

@@ -621,7 +621,7 @@ static void __init at91_add_device_rtt(void)
  *  Watchdog
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
+#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
 static struct platform_device at91sam9261_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,

arch/arm/mach-at91/at91sam9263_devices.c

@@ -854,7 +854,7 @@ static void __init at91_add_device_rtt(void)
  *  Watchdog
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
+#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
 static struct platform_device at91sam9263_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -609,7 +609,7 @@ static void __init at91_add_device_rtt(void)
  *  Watchdog
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
+#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
 static struct platform_device at91sam9rl_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,

arch/arm/mach-at91/gpio.c

@@ -490,7 +490,8 @@ postcore_initcall(at91_gpio_debugfs_init);
 
 /*--------------------------------------------------------------------------*/
 
-/* This lock class tells lockdep that GPIO irqs are in a different
+/*
+ * This lock class tells lockdep that GPIO irqs are in a different
  * category than their parents, so it won't report false recursion.
  */
 static struct lock_class_key gpio_lock_class;
@@ -509,9 +510,6 @@ void __init at91_gpio_irq_setup(void)
 		unsigned	id = this->id;
 		unsigned	i;
 
-		/* enable PIO controller's clock */
-		clk_enable(this->clock);
-
 		__raw_writel(~0, this->regbase + PIO_IDR);
 
 		for (i = 0, pin = this->chipbase; i < 32; i++, pin++) {
@@ -556,7 +554,14 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
 		data->chipbase = PIN_BASE + i * 32;
 		data->regbase = data->offset + (void __iomem *)AT91_VA_BASE_SYS;
 
-		/* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */
+		/* enable PIO controller's clock */
+		clk_enable(data->clock);
+
+		/*
+		 * Some processors share peripheral ID between multiple GPIO banks.
+		 *  SAM9263 (PIOC, PIOD, PIOE)
+		 *  CAP9 (PIOA, PIOB, PIOC, PIOD)
+		 */
 		if (last && last->id == data->id)
 			last->next = data;
 	}

arch/arm/mach-at91/include/mach/board.h

@@ -93,6 +93,7 @@ struct atmel_nand_data {
 	u8		enable_pin;	/* chip enable */
 	u8		det_pin;	/* card detect */
 	u8		rdy_pin;	/* ready/busy */
+	u8              rdy_pin_active_low;     /* rdy_pin value is inverted */
 	u8		ale;		/* address line number connected to ALE */
 	u8		cle;		/* address line number connected to CLE */
 	u8		bus_width_16;	/* buswidth is 16 bit */

arch/arm/mach-davinci/board-evm.c

@@ -311,6 +311,9 @@ evm_u35_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
 	gpio_request(gpio + 7, "nCF_SEL");
 	gpio_direction_output(gpio + 7, 1);
 
+	/* irlml6401 sustains over 3A, switches 5V in under 8 msec */
+	setup_usb(500, 8);
+
 	return 0;
 }
 
@@ -417,9 +420,6 @@ static __init void davinci_evm_init(void)
 	platform_add_devices(davinci_evm_devices,
 			     ARRAY_SIZE(davinci_evm_devices));
 	evm_init_i2c();
-
-	/* irlml6401 sustains over 3A, switches 5V in under 8 msec */
-	setup_usb(500, 8);
 }
 
 static __init void davinci_evm_irq_init(void)

arch/arm/mach-davinci/clock.c

@@ -230,6 +230,11 @@ static struct clk davinci_clks[] = {
 		.rate = &commonrate,
 		.lpsc = DAVINCI_LPSC_GPIO,
 	},
+	{
+		.name = "usb",
+		.rate = &commonrate,
+		.lpsc = DAVINCI_LPSC_USB,
+	},
 	{
 		.name = "AEMIFCLK",
 		.rate = &commonrate,

arch/arm/mach-davinci/usb.c

@@ -47,6 +47,7 @@ static struct musb_hdrc_platform_data usb_data = {
 #elif defined(CONFIG_USB_MUSB_HOST)
 	.mode           = MUSB_HOST,
 #endif
+	.clock		= "usb",
 	.config		= &musb_config,
 };
 

arch/arm/mach-ep93xx/include/mach/gesbc9312.h

@@ -1,3 +0,0 @@
-/*
- * arch/arm/mach-ep93xx/include/mach/gesbc9312.h
- */

arch/arm/mach-ep93xx/include/mach/hardware.h

@@ -10,7 +10,6 @@
 
 #include "platform.h"
 
-#include "gesbc9312.h"
 #include "ts72xx.h"
 
 #endif

arch/arm/mach-kirkwood/irq.c

@@ -42,7 +42,7 @@ void __init kirkwood_init_irq(void)
 	writel(0, GPIO_EDGE_CAUSE(32));
 
 	for (i = IRQ_KIRKWOOD_GPIO_START; i < NR_IRQS; i++) {
-		set_irq_chip(i, &orion_gpio_irq_level_chip);
+		set_irq_chip(i, &orion_gpio_irq_chip);
 		set_irq_handler(i, handle_level_irq);
 		irq_desc[i].status |= IRQ_LEVEL;
 		set_irq_flags(i, IRQF_VALID);

arch/arm/mach-mv78xx0/irq.c

@@ -40,7 +40,7 @@ void __init mv78xx0_init_irq(void)
 	writel(0, GPIO_EDGE_CAUSE(0));
 
 	for (i = IRQ_MV78XX0_GPIO_START; i < NR_IRQS; i++) {
-		set_irq_chip(i, &orion_gpio_irq_level_chip);
+		set_irq_chip(i, &orion_gpio_irq_chip);
 		set_irq_handler(i, handle_level_irq);
 		irq_desc[i].status |= IRQ_LEVEL;
 		set_irq_flags(i, IRQF_VALID);

arch/arm/mach-omap2/clock.c

@@ -565,7 +565,7 @@ u32 omap2_clksel_to_divisor(struct clk *clk, u32 field_val)
  *
  * Given a struct clk of a rate-selectable clksel clock, and a clock divisor,
  * find the corresponding register field value.  The return register value is
- * the value before left-shifting.  Returns 0xffffffff on error
+ * the value before left-shifting.  Returns ~0 on error
  */
 u32 omap2_divisor_to_clksel(struct clk *clk, u32 div)
 {
@@ -577,7 +577,7 @@ u32 omap2_divisor_to_clksel(struct clk *clk, u32 div)
 
 	clks = omap2_get_clksel_by_parent(clk, clk->parent);
 	if (clks == NULL)
-		return 0;
+		return ~0;
 
 	for (clkr = clks->rates; clkr->div; clkr++) {
 		if ((clkr->flags & cpu_mask) && (clkr->div == div))
@@ -588,7 +588,7 @@ u32 omap2_divisor_to_clksel(struct clk *clk, u32 div)
 		printk(KERN_ERR "clock: Could not find divisor %d for "
 		       "clock %s parent %s\n", div, clk->name,
 		       clk->parent->name);
-		return 0;
+		return ~0;
 	}
 
 	return clkr->val;
@@ -708,7 +708,7 @@ static u32 omap2_clksel_get_src_field(void __iomem **src_addr,
 		return 0;
 
 	for (clkr = clks->rates; clkr->div; clkr++) {
-		if (clkr->flags & (cpu_mask | DEFAULT_RATE))
+		if (clkr->flags & cpu_mask && clkr->flags & DEFAULT_RATE)
 			break; /* Found the default rate for this platform */
 	}
 
@@ -746,7 +746,7 @@ int omap2_clk_set_parent(struct clk *clk, struct clk *new_parent)
 		return -EINVAL;
 
 	if (clk->usecount > 0)
-		_omap2_clk_disable(clk);
+		omap2_clk_disable(clk);
 
 	/* Set new source value (previous dividers if any in effect) */
 	reg_val = __raw_readl(src_addr) & ~field_mask;
@@ -759,11 +759,11 @@ int omap2_clk_set_parent(struct clk *clk, struct clk *new_parent)
 		wmb();
 	}
 
-	if (clk->usecount > 0)
-		_omap2_clk_enable(clk);
-
 	clk->parent = new_parent;
 
+	if (clk->usecount > 0)
+		omap2_clk_enable(clk);
+
 	/* CLKSEL clocks follow their parents' rates, divided by a divisor */
 	clk->rate = new_parent->rate;
 

arch/arm/mach-orion5x/irq.c

@@ -44,7 +44,7 @@ void __init orion5x_init_irq(void)
 	 * User can use set_type() if he wants to use edge types handlers.
 	 */
 	for (i = IRQ_ORION5X_GPIO_START; i < NR_IRQS; i++) {
-		set_irq_chip(i, &orion_gpio_irq_level_chip);
+		set_irq_chip(i, &orion_gpio_irq_chip);
 		set_irq_handler(i, handle_level_irq);
 		irq_desc[i].status |= IRQ_LEVEL;
 		set_irq_flags(i, IRQF_VALID);

arch/arm/mach-rpc/riscpc.c

@@ -19,6 +19,7 @@
 #include <linux/serial_8250.h>
 #include <linux/ata_platform.h>
 #include <linux/io.h>
+#include <linux/i2c.h>
 
 #include <asm/elf.h>
 #include <asm/mach-types.h>
@@ -201,8 +202,13 @@ static struct platform_device *devs[] __initdata = {
 	&pata_device,
 };
 
+static struct i2c_board_info i2c_rtc = {
+	I2C_BOARD_INFO("pcf8583", 0x50)
+};
+
 static int __init rpc_init(void)
 {
+	i2c_register_board_info(0, &i2c_rtc, 1);
 	return platform_add_devices(devs, ARRAY_SIZE(devs));
 }
 

arch/arm/mm/mmu.c

@@ -693,7 +693,8 @@ static void __init sanity_check_meminfo(void)
 		 * Check whether this memory bank would entirely overlap
 		 * the vmalloc area.
 		 */
-		if (__va(bank->start) >= VMALLOC_MIN) {
+		if (__va(bank->start) >= VMALLOC_MIN ||
+		    __va(bank->start) < PAGE_OFFSET) {
 			printk(KERN_NOTICE "Ignoring RAM at %.8lx-%.8lx "
 			       "(vmalloc region overlap).\n",
 			       bank->start, bank->start + bank->size - 1);

arch/arm/plat-orion/gpio.c

@@ -265,51 +265,36 @@ EXPORT_SYMBOL(orion_gpio_set_blink);
  *        polarity    LEVEL          mask
  *
  ****************************************************************************/
-static void gpio_irq_edge_ack(u32 irq)
-{
-	int pin = irq_to_gpio(irq);
-
-	writel(~(1 << (pin & 31)), GPIO_EDGE_CAUSE(pin));
-}
-
-static void gpio_irq_edge_mask(u32 irq)
-{
-	int pin = irq_to_gpio(irq);
-	u32 u;
-
-	u = readl(GPIO_EDGE_MASK(pin));
-	u &= ~(1 << (pin & 31));
-	writel(u, GPIO_EDGE_MASK(pin));
-}
 
-static void gpio_irq_edge_unmask(u32 irq)
+static void gpio_irq_ack(u32 irq)
 {
-	int pin = irq_to_gpio(irq);
-	u32 u;
-
-	u = readl(GPIO_EDGE_MASK(pin));
-	u |= 1 << (pin & 31);
-	writel(u, GPIO_EDGE_MASK(pin));
+	int type = irq_desc[irq].status & IRQ_TYPE_SENSE_MASK;
+	if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) {
+		int pin = irq_to_gpio(irq);
+		writel(~(1 << (pin & 31)), GPIO_EDGE_CAUSE(pin));
+	}
 }
 
-static void gpio_irq_level_mask(u32 irq)
+static void gpio_irq_mask(u32 irq)
 {
 	int pin = irq_to_gpio(irq);
-	u32 u;
-
-	u = readl(GPIO_LEVEL_MASK(pin));
+	int type = irq_desc[irq].status & IRQ_TYPE_SENSE_MASK;
+	u32 reg = (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) ?
+		GPIO_EDGE_MASK(pin) : GPIO_LEVEL_MASK(pin);
+	u32 u = readl(reg);
 	u &= ~(1 << (pin & 31));
-	writel(u, GPIO_LEVEL_MASK(pin));
+	writel(u, reg);
 }
 
-static void gpio_irq_level_unmask(u32 irq)
+static void gpio_irq_unmask(u32 irq)
 {
 	int pin = irq_to_gpio(irq);
-	u32 u;
-
-	u = readl(GPIO_LEVEL_MASK(pin));
+	int type = irq_desc[irq].status & IRQ_TYPE_SENSE_MASK;
+	u32 reg = (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) ?
+		GPIO_EDGE_MASK(pin) : GPIO_LEVEL_MASK(pin);
+	u32 u = readl(reg);
 	u |= 1 << (pin & 31);
-	writel(u, GPIO_LEVEL_MASK(pin));
+	writel(u, reg);
 }
 
 static int gpio_irq_set_type(u32 irq, u32 type)
@@ -331,9 +316,9 @@ static int gpio_irq_set_type(u32 irq, u32 type)
 	 * Set edge/level type.
 	 */
 	if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) {
-		desc->chip = &orion_gpio_irq_edge_chip;
+		desc->handle_irq = handle_edge_irq;
 	} else if (type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
-		desc->chip = &orion_gpio_irq_level_chip;
+		desc->handle_irq = handle_level_irq;
 	} else {
 		printk(KERN_ERR "failed to set irq=%d (type=%d)\n", irq, type);
 		return -EINVAL;
@@ -371,19 +356,11 @@ static int gpio_irq_set_type(u32 irq, u32 type)
 	return 0;
 }
 
-struct irq_chip orion_gpio_irq_edge_chip = {
-	.name		= "orion_gpio_irq_edge",
-	.ack		= gpio_irq_edge_ack,
-	.mask		= gpio_irq_edge_mask,
-	.unmask		= gpio_irq_edge_unmask,
-	.set_type	= gpio_irq_set_type,
-};
-
-struct irq_chip orion_gpio_irq_level_chip = {
-	.name		= "orion_gpio_irq_level",
-	.mask		= gpio_irq_level_mask,
-	.mask_ack	= gpio_irq_level_mask,
-	.unmask		= gpio_irq_level_unmask,
+struct irq_chip orion_gpio_irq_chip = {
+	.name		= "orion_gpio",
+	.ack		= gpio_irq_ack,
+	.mask		= gpio_irq_mask,
+	.unmask		= gpio_irq_unmask,
 	.set_type	= gpio_irq_set_type,
 };
 

arch/arm/plat-orion/include/plat/gpio.h

@@ -31,8 +31,7 @@ void orion_gpio_set_blink(unsigned pin, int blink);
 /*
  * GPIO interrupt handling.
  */
-extern struct irq_chip orion_gpio_irq_edge_chip;
-extern struct irq_chip orion_gpio_irq_level_chip;
+extern struct irq_chip orion_gpio_irq_chip;
 void orion_gpio_irq_handler(int irqoff);
 
 

arch/avr32/mach-at32ap/include/mach/board.h

@@ -116,6 +116,7 @@ struct atmel_nand_data {
 	int	enable_pin;	/* chip enable */
 	int	det_pin;	/* card detect */
 	int	rdy_pin;	/* ready/busy */
+	u8	rdy_pin_active_low;	/* rdy_pin value is inverted */
 	u8	ale;		/* address line number connected to ALE */
 	u8	cle;		/* address line number connected to CLE */
 	u8	bus_width_16;	/* buswidth is 16 bit */

arch/ia64/Kconfig

@@ -221,7 +221,11 @@ config IA64_HP_SIM
 
 config IA64_XEN_GUEST
 	bool "Xen guest"
+	select SWIOTLB
 	depends on XEN
+	help
+	  Build a kernel that runs on Xen guest domain. At this moment only
+	  16KB page size in supported.
 
 endchoice
 
@@ -479,8 +483,7 @@ config HOLES_IN_ZONE
 	default y if VIRTUAL_MEM_MAP
 
 config HAVE_ARCH_EARLY_PFN_TO_NID
-	def_bool y
-	depends on NEED_MULTIPLE_NODES
+	def_bool NUMA && SPARSEMEM
 
 config HAVE_ARCH_NODEDATA_EXTENSION
 	def_bool y
@@ -635,6 +638,17 @@ config DMAR
 	  and include PCI device scope covered by these DMA
 	  remapping devices.
 
+config DMAR_DEFAULT_ON
+	def_bool y
+	prompt "Enable DMA Remapping Devices by default"
+	depends on DMAR
+	help
+	  Selecting this option will enable a DMAR device at boot time if
+	  one is found. If this option is not selected, DMAR support can
+	  be enabled by passing intel_iommu=on to the kernel. It is
+	  recommended you say N here while the DMAR code remains
+	  experimental.
+
 endmenu
 
 endif

arch/ia64/configs/xen_domu_defconfig

@@ -0,0 +1,1601 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.29-rc1
+# Fri Jan 16 11:49:59 2009
+#
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=20
+CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
+# CONFIG_GROUP_SCHED is not set
+
+#
+# Control Group support
+#
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+# CONFIG_EMBEDDED is not set
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_KALLSYMS_STRIP_GENERATED=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_PCI_QUIRKS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_USE_GENERIC_SMP_HELPERS=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_STOP_MACHINE=y
+CONFIG_BLOCK=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+CONFIG_FREEZER=y
+
+#
+# Processor type and features
+#
+CONFIG_IA64=y
+CONFIG_64BIT=y
+CONFIG_ZONE_DMA=y
+CONFIG_QUICKLIST=y
+CONFIG_MMU=y
+CONFIG_SWIOTLB=y
+CONFIG_IOMMU_HELPER=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_HAVE_SETUP_PER_CPU_AREA=y
+CONFIG_DMI=y
+CONFIG_EFI=y
+CONFIG_GENERIC_IOMAP=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+CONFIG_AUDIT_ARCH=y
+CONFIG_PARAVIRT_GUEST=y
+CONFIG_PARAVIRT=y
+CONFIG_XEN=y
+CONFIG_XEN_XENCOMM=y
+CONFIG_NO_IDLE_HZ=y
+# CONFIG_IA64_GENERIC is not set
+# CONFIG_IA64_DIG is not set
+# CONFIG_IA64_DIG_VTD is not set
+# CONFIG_IA64_HP_ZX1 is not set
+# CONFIG_IA64_HP_ZX1_SWIOTLB is not set
+# CONFIG_IA64_SGI_SN2 is not set
+# CONFIG_IA64_SGI_UV is not set
+# CONFIG_IA64_HP_SIM is not set
+CONFIG_IA64_XEN_GUEST=y
+# CONFIG_ITANIUM is not set
+CONFIG_MCKINLEY=y
+# CONFIG_IA64_PAGE_SIZE_4KB is not set
+# CONFIG_IA64_PAGE_SIZE_8KB is not set
+CONFIG_IA64_PAGE_SIZE_16KB=y
+# CONFIG_IA64_PAGE_SIZE_64KB is not set
+CONFIG_PGTABLE_3=y
+# CONFIG_PGTABLE_4 is not set
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+# CONFIG_SCHED_HRTICK is not set
+CONFIG_IA64_L1_CACHE_SHIFT=7
+CONFIG_IA64_CYCLONE=y
+CONFIG_IOSAPIC=y
+CONFIG_FORCE_MAX_ZONEORDER=17
+# CONFIG_VIRT_CPU_ACCOUNTING is not set
+CONFIG_SMP=y
+CONFIG_NR_CPUS=16
+CONFIG_HOTPLUG_CPU=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+# CONFIG_SCHED_SMT is not set
+CONFIG_PERMIT_BSP_REMOVE=y
+CONFIG_FORCE_CPEI_RETARGET=y
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_MIGRATION=y
+CONFIG_PHYS_ADDR_T_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_NR_QUICK=1
+CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_ARCH_SELECT_MEMORY_MODEL=y
+CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_SPARSEMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_VIRTUAL_MEM_MAP=y
+CONFIG_HOLES_IN_ZONE=y
+# CONFIG_IA32_SUPPORT is not set
+# CONFIG_COMPAT_FOR_U64_ALIGNMENT is not set
+CONFIG_IA64_MCA_RECOVERY=y
+CONFIG_PERFMON=y
+CONFIG_IA64_PALINFO=y
+# CONFIG_IA64_MC_ERR_INJECT is not set
+# CONFIG_IA64_ESI is not set
+# CONFIG_IA64_HP_AML_NFW is not set
+CONFIG_KEXEC=y
+# CONFIG_CRASH_DUMP is not set
+
+#
+# Firmware Drivers
+#
+# CONFIG_FIRMWARE_MEMMAP is not set
+CONFIG_EFI_VARS=y
+CONFIG_EFI_PCDP=y
+CONFIG_DMIID=y
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_HAVE_AOUT is not set
+CONFIG_BINFMT_MISC=m
+
+#
+# Power management and ACPI options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_ACPI=y
+CONFIG_ACPI_SLEEP=y
+CONFIG_ACPI_PROCFS=y
+CONFIG_ACPI_PROCFS_POWER=y
+CONFIG_ACPI_SYSFS_POWER=y
+CONFIG_ACPI_PROC_EVENT=y
+CONFIG_ACPI_BUTTON=m
+CONFIG_ACPI_FAN=m
+# CONFIG_ACPI_DOCK is not set
+CONFIG_ACPI_PROCESSOR=m
+CONFIG_ACPI_HOTPLUG_CPU=y
+CONFIG_ACPI_THERMAL=m
+# CONFIG_ACPI_CUSTOM_DSDT is not set
+CONFIG_ACPI_BLACKLIST_YEAR=0
+# CONFIG_ACPI_DEBUG is not set
+# CONFIG_ACPI_PCI_SLOT is not set
+CONFIG_ACPI_SYSTEM=y
+CONFIG_ACPI_CONTAINER=m
+
+#
+# CPU Frequency scaling
+#
+# CONFIG_CPU_FREQ is not set
+
+#
+# Bus options (PCI, PCMCIA)
+#
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCI_STUB is not set
+CONFIG_HOTPLUG_PCI=m
+# CONFIG_HOTPLUG_PCI_FAKE is not set
+CONFIG_HOTPLUG_PCI_ACPI=m
+# CONFIG_HOTPLUG_PCI_ACPI_IBM is not set
+# CONFIG_HOTPLUG_PCI_CPCI is not set
+# CONFIG_HOTPLUG_PCI_SHPC is not set
+# CONFIG_PCCARD is not set
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NET_NS is not set
+CONFIG_COMPAT_NET_DEV_OPS=y
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+CONFIG_ARPD=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_PHONET is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+# CONFIG_MTD is not set
+# CONFIG_PARPORT is not set
+CONFIG_PNP=y
+CONFIG_PNP_DEBUG_MESSAGES=y
+
+#
+# Protocols
+#
+CONFIG_PNPACPI=y
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+# CONFIG_BLK_DEV_SX8 is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_XEN_BLKDEV_FRONTEND=y
+# CONFIG_BLK_DEV_HD is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+# CONFIG_C2PORT is not set
+CONFIG_HAVE_IDE=y
+CONFIG_IDE=y
+
+#
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
+#
+CONFIG_IDE_TIMINGS=y
+CONFIG_IDE_ATAPI=y
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_IDE_GD=y
+CONFIG_IDE_GD_ATA=y
+# CONFIG_IDE_GD_ATAPI is not set
+CONFIG_BLK_DEV_IDECD=y
+CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEACPI is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
+
+#
+# IDE chipset support/bugfixes
+#
+# CONFIG_IDE_GENERIC is not set
+# CONFIG_BLK_DEV_PLATFORM is not set
+# CONFIG_BLK_DEV_IDEPNP is not set
+CONFIG_BLK_DEV_IDEDMA_SFF=y
+
+#
+# PCI IDE chipsets support
+#
+CONFIG_BLK_DEV_IDEPCI=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+CONFIG_BLK_DEV_GENERIC=y
+# CONFIG_BLK_DEV_OPTI621 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+CONFIG_BLK_DEV_CMD64X=y
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+CONFIG_BLK_DEV_PIIX=y
+# CONFIG_BLK_DEV_IT8172 is not set
+# CONFIG_BLK_DEV_IT8213 is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
+CONFIG_BLK_DEV_IDEDMA=y
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+CONFIG_SCSI_NETLINK=y
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+# CONFIG_CHR_DEV_OSST is not set
+CONFIG_BLK_DEV_SR=m
+# CONFIG_BLK_DEV_SR_VENDOR is not set
+CONFIG_CHR_DEV_SG=m
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+CONFIG_SCSI_SPI_ATTRS=y
+CONFIG_SCSI_FC_ATTRS=y
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ADVANSYS is not set
+# CONFIG_SCSI_ARCMSR is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_LIBFC is not set
+# CONFIG_FCOE is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_MVSAS is not set
+# CONFIG_SCSI_STEX is not set
+CONFIG_SCSI_SYM53C8XX_2=y
+CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
+CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
+CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
+CONFIG_SCSI_SYM53C8XX_MMIO=y
+CONFIG_SCSI_QLOGIC_1280=y
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_ATA is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+# CONFIG_MD_RAID10 is not set
+# CONFIG_MD_RAID456 is not set
+CONFIG_MD_MULTIPATH=m
+# CONFIG_MD_FAULTY is not set
+CONFIG_BLK_DEV_DM=m
+# CONFIG_DM_DEBUG is not set
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+# CONFIG_DM_MULTIPATH is not set
+# CONFIG_DM_DELAY is not set
+# CONFIG_DM_UEVENT is not set
+CONFIG_FUSION=y
+CONFIG_FUSION_SPI=y
+CONFIG_FUSION_FC=y
+# CONFIG_FUSION_SAS is not set
+CONFIG_FUSION_MAX_SGE=128
+CONFIG_FUSION_CTL=y
+# CONFIG_FUSION_LOGGING is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=m
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_NET_SB1000 is not set
+# CONFIG_ARCNET is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=m
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+CONFIG_NET_TULIP=y
+# CONFIG_DE2104X is not set
+CONFIG_TULIP=m
+# CONFIG_TULIP_MWI is not set
+# CONFIG_TULIP_MMIO is not set
+# CONFIG_TULIP_NAPI is not set
+# CONFIG_DE4X5 is not set
+# CONFIG_WINBOND_840 is not set
+# CONFIG_DM9102 is not set
+# CONFIG_ULI526X is not set
+# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+CONFIG_E100=m
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+# CONFIG_8139TOO is not set
+# CONFIG_R6040 is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SMSC9420 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+# CONFIG_SC92031 is not set
+# CONFIG_ATL2 is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+CONFIG_E1000=y
+# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+CONFIG_TIGON3=y
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
+# CONFIG_JME is not set
+CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+CONFIG_CHELSIO_T3_DEPENDS=y
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_ENIC is not set
+# CONFIG_IXGBE is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
+# CONFIG_MLX4_EN is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
+# CONFIG_BNX2X is not set
+# CONFIG_QLGE is not set
+# CONFIG_SFC is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+CONFIG_XEN_NETDEV_FRONTEND=y
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
+CONFIG_NETCONSOLE=y
+# CONFIG_NETCONSOLE_DYNAMIC is not set
+CONFIG_NETPOLL=y
+# CONFIG_NETPOLL_TRAP is not set
+CONFIG_NET_POLL_CONTROLLER=y
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
+# CONFIG_MOUSE_BCM5974 is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+# CONFIG_SERIO_SERPORT is not set
+# CONFIG_SERIO_PCIPS2 is not set
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+CONFIG_GAMEPORT=m
+# CONFIG_GAMEPORT_NS558 is not set
+# CONFIG_GAMEPORT_L4 is not set
+# CONFIG_GAMEPORT_EMU10K1 is not set
+# CONFIG_GAMEPORT_FM801 is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+CONFIG_SERIAL_NONSTANDARD=y
+# CONFIG_COMPUTONE is not set
+# CONFIG_ROCKETPORT is not set
+# CONFIG_CYCLADES is not set
+# CONFIG_DIGIEPCA is not set
+# CONFIG_MOXA_INTELLIO is not set
+# CONFIG_MOXA_SMARTIO is not set
+# CONFIG_ISI is not set
+# CONFIG_SYNCLINKMP is not set
+# CONFIG_SYNCLINK_GT is not set
+# CONFIG_N_HDLC is not set
+# CONFIG_RISCOM8 is not set
+# CONFIG_SPECIALIX is not set
+# CONFIG_SX is not set
+# CONFIG_RIO is not set
+# CONFIG_STALDRV is not set
+# CONFIG_NOZOMI is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_PNP=y
+CONFIG_SERIAL_8250_NR_UARTS=6
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+CONFIG_HVC_DRIVER=y
+CONFIG_HVC_IRQ=y
+CONFIG_HVC_XEN=y
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+CONFIG_EFI_RTC=y
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+CONFIG_RAW_DRIVER=m
+CONFIG_MAX_RAW_DEVS=256
+CONFIG_HPET=y
+CONFIG_HPET_MMAP=y
+# CONFIG_HANGCHECK_TIMER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_ALGOBIT=m
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# PC SMBus host controller drivers
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_ISCH is not set
+# CONFIG_I2C_PIIX4 is not set
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Graphics adapter I2C/DDC channel drivers
+#
+# CONFIG_I2C_VOODOO3 is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_AT24 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+# CONFIG_SPI is not set
+# CONFIG_W1 is not set
+CONFIG_POWER_SUPPLY=y
+# CONFIG_POWER_SUPPLY_DEBUG is not set
+# CONFIG_PDA_POWER is not set
+# CONFIG_BATTERY_DS2760 is not set
+# CONFIG_BATTERY_BQ27x00 is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_I5K_AMB is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_SENSORS_LIS3LV02D is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_THERMAL=m
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_REGULATOR is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
+CONFIG_DAB=y
+# CONFIG_USB_DABUSB is not set
+
+#
+# Graphics support
+#
+CONFIG_AGP=m
+CONFIG_DRM=m
+CONFIG_DRM_TDFX=m
+CONFIG_DRM_R128=m
+CONFIG_DRM_RADEON=m
+CONFIG_DRM_MGA=m
+CONFIG_DRM_SIS=m
+# CONFIG_DRM_VIA is not set
+# CONFIG_DRM_SAVAGE is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+CONFIG_VGA_CONSOLE=y
+# CONFIG_VGACON_SOFT_SCROLLBACK is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_HID_PID is not set
+# CONFIG_USB_HIDDEV is not set
+
+#
+# Special HID drivers
+#
+CONFIG_HID_COMPAT=y
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+CONFIG_HID_EZKEY=y
+CONFIG_HID_GYRATION=y
+CONFIG_HID_LOGITECH=y
+# CONFIG_LOGITECH_FF is not set
+# CONFIG_LOGIRUMBLEPAD2_FF is not set
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+CONFIG_HID_NTRIG=y
+CONFIG_HID_PANTHERLORD=y
+# CONFIG_PANTHERLORD_FF is not set
+CONFIG_HID_PETALYNX=y
+CONFIG_HID_SAMSUNG=y
+CONFIG_HID_SONY=y
+CONFIG_HID_SUNPLUS=y
+# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_TOPSEED=y
+# CONFIG_THRUSTMASTER_FF is not set
+# CONFIG_ZEROPLUS_FF is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_MON is not set
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=m
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+CONFIG_USB_OHCI_HCD=m
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+CONFIG_USB_UHCI_HCD=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_WHCI_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
+#
+
+#
+# see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+# CONFIG_USB_GADGET is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_UWB is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_UIO is not set
+CONFIG_XEN_BALLOON=y
+CONFIG_XEN_SCRUB_PAGES=y
+CONFIG_XENFS=y
+CONFIG_XEN_COMPAT_XENFS=y
+# CONFIG_STAGING is not set
+# CONFIG_MSPEC is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+CONFIG_FS_MBCACHE=y
+CONFIG_REISERFS_FS=y
+# CONFIG_REISERFS_CHECK is not set
+# CONFIG_REISERFS_PROC_INFO is not set
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+CONFIG_FILE_LOCKING=y
+CONFIG_XFS_FS=y
+# CONFIG_XFS_QUOTA is not set
+# CONFIG_XFS_POSIX_ACL is not set
+# CONFIG_XFS_RT is not set
+# CONFIG_XFS_DEBUG is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_AUTOFS4_FS=y
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+# CONFIG_ZISOFS is not set
+CONFIG_UDF_FS=m
+CONFIG_UDF_NLS=y
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+# CONFIG_MSDOS_FS is not set
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_NTFS_FS=m
+# CONFIG_NTFS_DEBUG is not set
+# CONFIG_NTFS_RW is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+CONFIG_HUGETLBFS=y
+CONFIG_HUGETLB_PAGE=y
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3=y
+# CONFIG_NFSD_V3_ACL is not set
+CONFIG_NFSD_V4=y
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_EXPORTFS=m
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=m
+CONFIG_SUNRPC_GSS=m
+# CONFIG_SUNRPC_REGISTER_V4 is not set
+CONFIG_RPCSEC_GSS_KRB5=m
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+CONFIG_SMB_FS=m
+CONFIG_SMB_NLS_DEFAULT=y
+CONFIG_SMB_NLS_REMOTE="cp437"
+CONFIG_CIFS=m
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_WEAK_PW_HASH is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_EXPERIMENTAL is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_BSD_DISKLABEL is not set
+# CONFIG_MINIX_SUBPARTITION is not set
+# CONFIG_SOLARIS_X86_PARTITION is not set
+# CONFIG_UNIXWARE_DISKLABEL is not set
+# CONFIG_LDM_PARTITION is not set
+CONFIG_SGI_PARTITION=y
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+CONFIG_EFI_PARTITION=y
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=2048
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+
+#
+# Tracers
+#
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
+# CONFIG_SAMPLES is not set
+CONFIG_IA64_GRANULE_16MB=y
+# CONFIG_IA64_GRANULE_64MB is not set
+# CONFIG_IA64_PRINT_HAZARDS is not set
+# CONFIG_DISABLE_VHPT is not set
+# CONFIG_IA64_DEBUG_CMPXCHG is not set
+# CONFIG_IA64_DEBUG_IRQ is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=m
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_MANAGER=m
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=m
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=m
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
+CONFIG_HAVE_KVM=y
+CONFIG_VIRTUALIZATION=y
+# CONFIG_KVM is not set
+# CONFIG_VIRTIO_PCI is not set
+# CONFIG_VIRTIO_BALLOON is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+CONFIG_CRC_ITU_T=m
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_GENERIC_PENDING_IRQ=y
+CONFIG_IRQ_PER_CPU=y
+# CONFIG_IOMMU_API is not set

arch/ia64/include/asm/mmzone.h

@@ -31,10 +31,6 @@ static inline int pfn_to_nid(unsigned long pfn)
 #endif
 }
 
-#ifdef CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID
-extern int early_pfn_to_nid(unsigned long pfn);
-#endif
-
 #ifdef CONFIG_IA64_DIG /* DIG systems are small */
 # define MAX_PHYSNODE_ID	8
 # define NR_NODE_MEMBLKS	(MAX_NUMNODES * 8)

arch/ia64/include/asm/sn/bte.h

@@ -39,7 +39,7 @@
 /* BTE status register only supports 16 bits for length field */
 #define BTE_LEN_BITS (16)
 #define BTE_LEN_MASK ((1 << BTE_LEN_BITS) - 1)
-#define BTE_MAX_XFER ((1 << BTE_LEN_BITS) * L1_CACHE_BYTES)
+#define BTE_MAX_XFER (BTE_LEN_MASK << L1_CACHE_SHIFT)
 
 
 /* Define hardware */

arch/ia64/kernel/iosapic.c

@@ -507,7 +507,7 @@ static int iosapic_find_sharable_irq(unsigned long trigger, unsigned long pol)
 	if (trigger == IOSAPIC_EDGE)
 		return -EINVAL;
 
-	for (i = 0; i <= NR_IRQS; i++) {
+	for (i = 0; i < NR_IRQS; i++) {
 		info = &iosapic_intr_info[i];
 		if (info->trigger == trigger && info->polarity == pol &&
 		    (info->dmode == IOSAPIC_FIXED ||

arch/ia64/kernel/smpboot.c

@@ -736,14 +736,15 @@ int __cpu_disable(void)
 			return -EBUSY;
 	}
 
+	cpu_clear(cpu, cpu_online_map);
+
 	if (migrate_platform_irqs(cpu)) {
 		cpu_set(cpu, cpu_online_map);
-		return (-EBUSY);
+		return -EBUSY;
 	}
 
 	remove_siblinginfo(cpu);
 	fixup_irqs();
-	cpu_clear(cpu, cpu_online_map);
 	local_flush_tlb_all();
 	cpu_clear(cpu, cpu_callin_map);
 	return 0;

arch/ia64/kernel/unwind.c

@@ -2149,7 +2149,7 @@ unw_remove_unwind_table (void *handle)
 
 	/* next, remove hash table entries for this table */
 
-	for (index = 0; index <= UNW_HASH_SIZE; ++index) {
+	for (index = 0; index < UNW_HASH_SIZE; ++index) {
 		tmp = unw.cache + unw.hash[index];
 		if (unw.hash[index] >= UNW_CACHE_SIZE
 		    || tmp->ip < table->start || tmp->ip >= table->end)

arch/ia64/mm/numa.c

@@ -58,7 +58,7 @@ paddr_to_nid(unsigned long paddr)
  * SPARSEMEM to allocate the SPARSEMEM sectionmap on the NUMA node where
  * the section resides.
  */
-int early_pfn_to_nid(unsigned long pfn)
+int __meminit __early_pfn_to_nid(unsigned long pfn)
 {
 	int i, section = pfn >> PFN_SECTION_SHIFT, ssec, esec;
 
@@ -70,7 +70,7 @@ int early_pfn_to_nid(unsigned long pfn)
 			return node_memblk[i].nid;
 	}
 
-	return 0;
+	return -1;
 }
 
 #ifdef CONFIG_MEMORY_HOTPLUG

arch/ia64/sn/kernel/bte.c

@@ -97,9 +97,10 @@ bte_result_t bte_copy(u64 src, u64 dest, u64 len, u64 mode, void *notification)
 		return BTE_SUCCESS;
 	}
 
-	BUG_ON((len & L1_CACHE_MASK) ||
-		 (src & L1_CACHE_MASK) || (dest & L1_CACHE_MASK));
-	BUG_ON(!(len < ((BTE_LEN_MASK + 1) << L1_CACHE_SHIFT)));
+	BUG_ON(len & L1_CACHE_MASK);
+	BUG_ON(src & L1_CACHE_MASK);
+	BUG_ON(dest & L1_CACHE_MASK);
+	BUG_ON(len > BTE_MAX_XFER);
 
 	/*
 	 * Start with interface corresponding to cpu number

arch/ia64/xen/Kconfig

@@ -8,8 +8,7 @@ config XEN
 	depends on PARAVIRT && MCKINLEY && IA64_PAGE_SIZE_16KB && EXPERIMENTAL
 	select XEN_XENCOMM
 	select NO_IDLE_HZ
-
-	# those are required to save/restore.
+	# followings are required to save/restore.
 	select ARCH_SUSPEND_POSSIBLE
 	select SUSPEND
 	select PM_SLEEP

arch/ia64/xen/xen_pv_ops.c

@@ -153,7 +153,7 @@ xen_post_smp_prepare_boot_cpu(void)
 	xen_setup_vcpu_info_placement();
 }
 
-static const struct pv_init_ops xen_init_ops __initdata = {
+static const struct pv_init_ops xen_init_ops __initconst = {
 	.banner = xen_banner,
 
 	.reserve_memory = xen_reserve_memory,
@@ -337,7 +337,7 @@ xen_iosapic_write(char __iomem *iosapic, unsigned int reg, u32 val)
 	HYPERVISOR_physdev_op(PHYSDEVOP_apic_write, &apic_op);
 }
 
-static const struct pv_iosapic_ops xen_iosapic_ops __initdata = {
+static const struct pv_iosapic_ops xen_iosapic_ops __initconst = {
 	.pcat_compat_init = xen_pcat_compat_init,
 	.__get_irq_chip = xen_iosapic_get_irq_chip,
 

arch/m68k/atari/ataints.c

@@ -187,8 +187,8 @@ __asm__ (__ALIGN_STR "\n"						   \
 "	jbra	ret_from_interrupt\n"					   \
 	 : : "i" (&kstat_cpu(0).irqs[n+8]), "i" (&irq_handler[n+8]),	   \
 	     "n" (PT_OFF_SR), "n" (n),					   \
-	     "i" (n & 8 ? (n & 16 ? &tt_mfp.int_mk_a : &mfp.int_mk_a)	   \
-		        : (n & 16 ? &tt_mfp.int_mk_b : &mfp.int_mk_b)),	   \
+	     "i" (n & 8 ? (n & 16 ? &tt_mfp.int_mk_a : &st_mfp.int_mk_a)   \
+		        : (n & 16 ? &tt_mfp.int_mk_b : &st_mfp.int_mk_b)), \
 	     "m" (preempt_count()), "di" (HARDIRQ_OFFSET)		   \
 );									   \
 	for (;;);			/* fake noreturn */		   \
@@ -366,14 +366,14 @@ void __init atari_init_IRQ(void)
 	/* Initialize the MFP(s) */
 
 #ifdef ATARI_USE_SOFTWARE_EOI
-	mfp.vec_adr  = 0x48;	/* Software EOI-Mode */
+	st_mfp.vec_adr  = 0x48;	/* Software EOI-Mode */
 #else
-	mfp.vec_adr  = 0x40;	/* Automatic EOI-Mode */
+	st_mfp.vec_adr  = 0x40;	/* Automatic EOI-Mode */
 #endif
-	mfp.int_en_a = 0x00;	/* turn off MFP-Ints */
-	mfp.int_en_b = 0x00;
-	mfp.int_mk_a = 0xff;	/* no Masking */
-	mfp.int_mk_b = 0xff;
+	st_mfp.int_en_a = 0x00;	/* turn off MFP-Ints */
+	st_mfp.int_en_b = 0x00;
+	st_mfp.int_mk_a = 0xff;	/* no Masking */
+	st_mfp.int_mk_b = 0xff;
 
 	if (ATARIHW_PRESENT(TT_MFP)) {
 #ifdef ATARI_USE_SOFTWARE_EOI

arch/m68k/atari/atakeyb.c

@@ -609,10 +609,10 @@ int atari_keyb_init(void)
 				 ACIA_RHTID : 0);
 
 	/* make sure the interrupt line is up */
-	} while ((mfp.par_dt_reg & 0x10) == 0);
+	} while ((st_mfp.par_dt_reg & 0x10) == 0);
 
 	/* enable ACIA Interrupts */
-	mfp.active_edge &= ~0x10;
+	st_mfp.active_edge &= ~0x10;
 	atari_turnon_irq(IRQ_MFP_ACIA);
 
 	ikbd_self_test = 1;

arch/m68k/atari/config.c

@@ -258,7 +258,7 @@ void __init config_atari(void)
 			printk("STND_SHIFTER ");
 		}
 	}
-	if (hwreg_present(&mfp.par_dt_reg)) {
+	if (hwreg_present(&st_mfp.par_dt_reg)) {
 		ATARIHW_SET(ST_MFP);
 		printk("ST_MFP ");
 	}

arch/m68k/atari/debug.c

@@ -34,9 +34,9 @@ static struct console atari_console_driver = {
 
 static inline void ata_mfp_out(char c)
 {
-	while (!(mfp.trn_stat & 0x80))	/* wait for tx buf empty */
+	while (!(st_mfp.trn_stat & 0x80))	/* wait for tx buf empty */
 		barrier();
-	mfp.usart_dta = c;
+	st_mfp.usart_dta = c;
 }
 
 static void atari_mfp_console_write(struct console *co, const char *str,
@@ -91,7 +91,7 @@ static int ata_par_out(char c)
 	/* This a some-seconds timeout in case no printer is connected */
 	unsigned long i = loops_per_jiffy > 1 ? loops_per_jiffy : 10000000/HZ;
 
-	while ((mfp.par_dt_reg & 1) && --i) /* wait for BUSY == L */
+	while ((st_mfp.par_dt_reg & 1) && --i) /* wait for BUSY == L */
 		;
 	if (!i)
 		return 0;
@@ -131,9 +131,9 @@ static void atari_par_console_write(struct console *co, const char *str,
 #if 0
 int atari_mfp_console_wait_key(struct console *co)
 {
-	while (!(mfp.rcv_stat & 0x80))	/* wait for rx buf filled */
+	while (!(st_mfp.rcv_stat & 0x80))	/* wait for rx buf filled */
 		barrier();
-	return mfp.usart_dta;
+	return st_mfp.usart_dta;
 }
 
 int atari_scc_console_wait_key(struct console *co)
@@ -175,12 +175,12 @@ static void __init atari_init_mfp_port(int cflag)
 		baud = B9600;		/* use default 9600bps for non-implemented rates */
 	baud -= B1200;			/* baud_table[] starts at 1200bps */
 
-	mfp.trn_stat &= ~0x01;		/* disable TX */
-	mfp.usart_ctr = parity | csize | 0x88; /* 1:16 clk mode, 1 stop bit */
-	mfp.tim_ct_cd &= 0x70;		/* stop timer D */
-	mfp.tim_dt_d = baud_table[baud];
-	mfp.tim_ct_cd |= 0x01;		/* start timer D, 1:4 */
-	mfp.trn_stat |= 0x01;		/* enable TX */
+	st_mfp.trn_stat &= ~0x01;	/* disable TX */
+	st_mfp.usart_ctr = parity | csize | 0x88; /* 1:16 clk mode, 1 stop bit */
+	st_mfp.tim_ct_cd &= 0x70;	/* stop timer D */
+	st_mfp.tim_dt_d = baud_table[baud];
+	st_mfp.tim_ct_cd |= 0x01;	/* start timer D, 1:4 */
+	st_mfp.trn_stat |= 0x01;	/* enable TX */
 }
 
 #define SCC_WRITE(reg, val)				\

arch/m68k/atari/time.c

@@ -27,9 +27,9 @@ void __init
 atari_sched_init(irq_handler_t timer_routine)
 {
     /* set Timer C data Register */
-    mfp.tim_dt_c = INT_TICKS;
+    st_mfp.tim_dt_c = INT_TICKS;
     /* start timer C, div = 1:100 */
-    mfp.tim_ct_cd = (mfp.tim_ct_cd & 15) | 0x60;
+    st_mfp.tim_ct_cd = (st_mfp.tim_ct_cd & 15) | 0x60;
     /* install interrupt service routine for MFP Timer C */
     if (request_irq(IRQ_MFP_TIMC, timer_routine, IRQ_TYPE_SLOW,
 		    "timer", timer_routine))
@@ -46,11 +46,11 @@ unsigned long atari_gettimeoffset (void)
   unsigned long ticks, offset = 0;
 
   /* read MFP timer C current value */
-  ticks = mfp.tim_dt_c;
+  ticks = st_mfp.tim_dt_c;
   /* The probability of underflow is less than 2% */
   if (ticks > INT_TICKS - INT_TICKS / 50)
     /* Check for pending timer interrupt */
-    if (mfp.int_pn_b & (1 << 5))
+    if (st_mfp.int_pn_b & (1 << 5))
       offset = TICK_SIZE;
 
   ticks = INT_TICKS - ticks;

arch/m68k/include/asm/atarihw.h

@@ -113,7 +113,7 @@ extern struct atari_hw_present atari_hw_present;
  * of nops on various machines. Somebody claimed that the tstb takes 600 ns.
  */
 #define	MFPDELAY() \
-	__asm__ __volatile__ ( "tstb %0" : : "m" (mfp.par_dt_reg) : "cc" );
+	__asm__ __volatile__ ( "tstb %0" : : "m" (st_mfp.par_dt_reg) : "cc" );
 
 /* Do cache push/invalidate for DMA read/write. This function obeys the
  * snooping on some machines (Medusa) and processors: The Medusa itself can
@@ -565,7 +565,7 @@ struct MFP
   u_char char_dummy23;
   u_char usart_dta;
  };
-# define mfp ((*(volatile struct MFP*)MFP_BAS))
+# define st_mfp ((*(volatile struct MFP*)MFP_BAS))
 
 /* TT's second MFP */
 

arch/m68k/include/asm/atariints.h

@@ -113,7 +113,7 @@ static inline int get_mfp_bit( unsigned irq, int type )
 {	unsigned char	mask, *reg;
 
 	mask = 1 << (irq & 7);
-	reg = (unsigned char *)&mfp.int_en_a + type*4 +
+	reg = (unsigned char *)&st_mfp.int_en_a + type*4 +
 		  ((irq & 8) >> 2) + (((irq-8) & 16) << 3);
 	return( *reg & mask );
 }
@@ -123,7 +123,7 @@ static inline void set_mfp_bit( unsigned irq, int type )
 {	unsigned char	mask, *reg;
 
 	mask = 1 << (irq & 7);
-	reg = (unsigned char *)&mfp.int_en_a + type*4 +
+	reg = (unsigned char *)&st_mfp.int_en_a + type*4 +
 		  ((irq & 8) >> 2) + (((irq-8) & 16) << 3);
 	__asm__ __volatile__ ( "orb %0,%1"
 			      : : "di" (mask), "m" (*reg) : "memory" );
@@ -134,7 +134,7 @@ static inline void clear_mfp_bit( unsigned irq, int type )
 {	unsigned char	mask, *reg;
 
 	mask = ~(1 << (irq & 7));
-	reg = (unsigned char *)&mfp.int_en_a + type*4 +
+	reg = (unsigned char *)&st_mfp.int_en_a + type*4 +
 		  ((irq & 8) >> 2) + (((irq-8) & 16) << 3);
 	if (type == MFP_PENDING || type == MFP_SERVICE)
 		__asm__ __volatile__ ( "moveb %0,%1"

arch/mips/Kconfig

@@ -603,7 +603,7 @@ config CAVIUM_OCTEON_SIMULATOR
 	select SYS_SUPPORTS_64BIT_KERNEL
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_HIGHMEM
-	select CPU_CAVIUM_OCTEON
+	select SYS_HAS_CPU_CAVIUM_OCTEON
 	help
 	  The Octeon simulator is software performance model of the Cavium
 	  Octeon Processor. It supports simulating Octeon processors on x86
@@ -618,7 +618,7 @@ config CAVIUM_OCTEON_REFERENCE_BOARD
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_HIGHMEM
 	select SYS_HAS_EARLY_PRINTK
-	select CPU_CAVIUM_OCTEON
+	select SYS_HAS_CPU_CAVIUM_OCTEON
 	select SWAP_IO_SPACE
 	help
 	  This option supports all of the Octeon reference boards from Cavium
@@ -1234,6 +1234,7 @@ config CPU_SB1
 
 config CPU_CAVIUM_OCTEON
 	bool "Cavium Octeon processor"
+	depends on SYS_HAS_CPU_CAVIUM_OCTEON
 	select IRQ_CPU
 	select IRQ_CPU_OCTEON
 	select CPU_HAS_PREFETCH
@@ -1314,6 +1315,9 @@ config SYS_HAS_CPU_RM9000
 config SYS_HAS_CPU_SB1
 	bool
 
+config SYS_HAS_CPU_CAVIUM_OCTEON
+	bool
+
 #
 # CPU may reorder R->R, R->W, W->R, W->W
 # Reordering beyond LL and SC is handled in WEAK_REORDERING_BEYOND_LLSC
@@ -1387,6 +1391,7 @@ config 32BIT
 config 64BIT
 	bool "64-bit kernel"
 	depends on CPU_SUPPORTS_64BIT_KERNEL && SYS_SUPPORTS_64BIT_KERNEL
+	select HAVE_SYSCALL_WRAPPERS
 	help
 	  Select this option if you want to build a 64-bit kernel.
 

arch/mips/alchemy/common/time.c

@@ -118,7 +118,7 @@ void __init plat_time_init(void)
 	 * setup counter 1 (RTC) to tick at full speed
 	 */
 	t = 0xffffff;
-	while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_T1S) && t--)
+	while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_T1S) && --t)
 		asm volatile ("nop");
 	if (!t)
 		goto cntr_err;
@@ -127,7 +127,7 @@ void __init plat_time_init(void)
 	au_sync();
 
 	t = 0xffffff;
-	while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && t--)
+	while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && --t)
 		asm volatile ("nop");
 	if (!t)
 		goto cntr_err;
@@ -135,7 +135,7 @@ void __init plat_time_init(void)
 	au_sync();
 
 	t = 0xffffff;
-	while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && t--)
+	while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && --t)
 		asm volatile ("nop");
 	if (!t)
 		goto cntr_err;

arch/mips/include/asm/seccomp.h

@@ -1,6 +1,5 @@
 #ifndef __ASM_SECCOMP_H
 
-#include <linux/thread_info.h>
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

arch/mips/kernel/irq.c

@@ -111,7 +111,6 @@ int show_interrupts(struct seq_file *p, void *v)
 			seq_printf(p, "%10u ", kstat_cpu(j).irqs[i]);
 #endif
 		seq_printf(p, " %14s", irq_desc[i].chip->name);
-		seq_printf(p, "-%-8s", irq_desc[i].name);
 		seq_printf(p, "  %s", action->name);
 
 		for (action=action->next; action; action = action->next)

arch/mips/kernel/linux32.c

@@ -32,6 +32,7 @@
 #include <linux/module.h>
 #include <linux/binfmts.h>
 #include <linux/security.h>
+#include <linux/syscalls.h>
 #include <linux/compat.h>
 #include <linux/vfs.h>
 #include <linux/ipc.h>
@@ -63,9 +64,9 @@
 #define merge_64(r1, r2) ((((r2) & 0xffffffffUL) << 32) + ((r1) & 0xffffffffUL))
 #endif
 
-asmlinkage unsigned long
-sys32_mmap2(unsigned long addr, unsigned long len, unsigned long prot,
-         unsigned long flags, unsigned long fd, unsigned long pgoff)
+SYSCALL_DEFINE6(32_mmap2, unsigned long, addr, unsigned long, len,
+	unsigned long, prot, unsigned long, flags, unsigned long, fd,
+	unsigned long, pgoff)
 {
 	struct file * file = NULL;
 	unsigned long error;
@@ -121,21 +122,21 @@ struct rlimit32 {
 	int	rlim_max;
 };
 
-asmlinkage long sys32_truncate64(const char __user * path,
-	unsigned long __dummy, int a2, int a3)
+SYSCALL_DEFINE4(32_truncate64, const char __user *, path,
+	unsigned long, __dummy, unsigned long, a2, unsigned long, a3)
 {
 	return sys_truncate(path, merge_64(a2, a3));
 }
 
-asmlinkage long sys32_ftruncate64(unsigned int fd, unsigned long __dummy,
-	int a2, int a3)
+SYSCALL_DEFINE4(32_ftruncate64, unsigned long, fd, unsigned long, __dummy,
+	unsigned long, a2, unsigned long, a3)
 {
 	return sys_ftruncate(fd, merge_64(a2, a3));
 }
 
-asmlinkage int sys32_llseek(unsigned int fd, unsigned int offset_high,
-			    unsigned int offset_low, loff_t __user * result,
-			    unsigned int origin)
+SYSCALL_DEFINE5(32_llseek, unsigned long, fd, unsigned long, offset_high,
+	unsigned long, offset_low, loff_t __user *, result,
+	unsigned long, origin)
 {
 	return sys_llseek(fd, offset_high, offset_low, result, origin);
 }
@@ -144,20 +145,20 @@ asmlinkage int sys32_llseek(unsigned int fd, unsigned int offset_high,
    lseek back to original location.  They fail just like lseek does on
    non-seekable files.  */
 
-asmlinkage ssize_t sys32_pread(unsigned int fd, char __user * buf,
-			       size_t count, u32 unused, u64 a4, u64 a5)
+SYSCALL_DEFINE6(32_pread, unsigned long, fd, char __user *, buf, size_t, count,
+	unsigned long, unused, unsigned long, a4, unsigned long, a5)
 {
 	return sys_pread64(fd, buf, count, merge_64(a4, a5));
 }
 
-asmlinkage ssize_t sys32_pwrite(unsigned int fd, const char __user * buf,
-			        size_t count, u32 unused, u64 a4, u64 a5)
+SYSCALL_DEFINE6(32_pwrite, unsigned int, fd, const char __user *, buf,
+	size_t, count, u32, unused, u64, a4, u64, a5)
 {
 	return sys_pwrite64(fd, buf, count, merge_64(a4, a5));
 }
 
-asmlinkage int sys32_sched_rr_get_interval(compat_pid_t pid,
-	struct compat_timespec __user *interval)
+SYSCALL_DEFINE2(32_sched_rr_get_interval, compat_pid_t, pid,
+	struct compat_timespec __user *, interval)
 {
 	struct timespec t;
 	int ret;
@@ -174,8 +175,8 @@ asmlinkage int sys32_sched_rr_get_interval(compat_pid_t pid,
 
 #ifdef CONFIG_SYSVIPC
 
-asmlinkage long
-sys32_ipc(u32 call, int first, int second, int third, u32 ptr, u32 fifth)
+SYSCALL_DEFINE6(32_ipc, u32, call, long, first, long, second, long, third,
+	unsigned long, ptr, unsigned long, fifth)
 {
 	int version, err;
 
@@ -233,8 +234,8 @@ sys32_ipc(u32 call, int first, int second, int third, u32 ptr, u32 fifth)
 
 #else
 
-asmlinkage long
-sys32_ipc(u32 call, int first, int second, int third, u32 ptr, u32 fifth)
+SYSCALL_DEFINE6(32_ipc, u32, call, int, first, int, second, int, third,
+	u32, ptr, u32 fifth)
 {
 	return -ENOSYS;
 }
@@ -242,7 +243,7 @@ sys32_ipc(u32 call, int first, int second, int third, u32 ptr, u32 fifth)
 #endif /* CONFIG_SYSVIPC */
 
 #ifdef CONFIG_MIPS32_N32
-asmlinkage long sysn32_semctl(int semid, int semnum, int cmd, u32 arg)
+SYSCALL_DEFINE4(n32_semctl, int, semid, int, semnum, int, cmd, u32, arg)
 {
 	/* compat_sys_semctl expects a pointer to union semun */
 	u32 __user *uptr = compat_alloc_user_space(sizeof(u32));
@@ -251,13 +252,14 @@ asmlinkage long sysn32_semctl(int semid, int semnum, int cmd, u32 arg)
 	return compat_sys_semctl(semid, semnum, cmd, uptr);
 }
 
-asmlinkage long sysn32_msgsnd(int msqid, u32 msgp, unsigned msgsz, int msgflg)
+SYSCALL_DEFINE4(n32_msgsnd, int, msqid, u32, msgp, unsigned int, msgsz,
+	int, msgflg)
 {
 	return compat_sys_msgsnd(msqid, msgsz, msgflg, compat_ptr(msgp));
 }
 
-asmlinkage long sysn32_msgrcv(int msqid, u32 msgp, size_t msgsz, int msgtyp,
-			      int msgflg)
+SYSCALL_DEFINE5(n32_msgrcv, int, msqid, u32, msgp, size_t, msgsz,
+	int, msgtyp, int, msgflg)
 {
 	return compat_sys_msgrcv(msqid, msgsz, msgtyp, msgflg, IPC_64,
 				 compat_ptr(msgp));
@@ -277,7 +279,7 @@ struct sysctl_args32
 
 #ifdef CONFIG_SYSCTL_SYSCALL
 
-asmlinkage long sys32_sysctl(struct sysctl_args32 __user *args)
+SYSCALL_DEFINE1(32_sysctl, struct sysctl_args32 __user *, args)
 {
 	struct sysctl_args32 tmp;
 	int error;
@@ -316,9 +318,16 @@ asmlinkage long sys32_sysctl(struct sysctl_args32 __user *args)
 	return error;
 }
 
+#else
+
+SYSCALL_DEFINE1(32_sysctl, struct sysctl_args32 __user *, args)
+{
+	return -ENOSYS;
+}
+
 #endif /* CONFIG_SYSCTL_SYSCALL */
 
-asmlinkage long sys32_newuname(struct new_utsname __user * name)
+SYSCALL_DEFINE1(32_newuname, struct new_utsname __user *, name)
 {
 	int ret = 0;
 
@@ -334,7 +343,7 @@ asmlinkage long sys32_newuname(struct new_utsname __user * name)
 	return ret;
 }
 
-asmlinkage int sys32_personality(unsigned long personality)
+SYSCALL_DEFINE1(32_personality, unsigned long, personality)
 {
 	int ret;
 	personality &= 0xffffffff;
@@ -357,7 +366,7 @@ struct ustat32 {
 
 extern asmlinkage long sys_ustat(dev_t dev, struct ustat __user * ubuf);
 
-asmlinkage int sys32_ustat(dev_t dev, struct ustat32 __user * ubuf32)
+SYSCALL_DEFINE2(32_ustat, dev_t, dev, struct ustat32 __user *, ubuf32)
 {
 	int err;
 	struct ustat tmp;
@@ -381,8 +390,8 @@ out:
 	return err;
 }
 
-asmlinkage int sys32_sendfile(int out_fd, int in_fd, compat_off_t __user *offset,
-	s32 count)
+SYSCALL_DEFINE4(32_sendfile, long, out_fd, long, in_fd,
+	compat_off_t __user *, offset, s32, count)
 {
 	mm_segment_t old_fs = get_fs();
 	int ret;

arch/mips/kernel/scall32-o32.S

@@ -399,7 +399,7 @@ einval:	li	v0, -ENOSYS
 	sys	sys_swapon		2
 	sys	sys_reboot		3
 	sys	sys_old_readdir		3
-	sys	old_mmap		6	/* 4090 */
+	sys	sys_mips_mmap		6	/* 4090 */
 	sys	sys_munmap		2
 	sys	sys_truncate		2
 	sys	sys_ftruncate		2
@@ -519,7 +519,7 @@ einval:	li	v0, -ENOSYS
 	sys	sys_sendfile		4
 	sys	sys_ni_syscall		0
 	sys	sys_ni_syscall		0
-	sys	sys_mmap2		6	/* 4210 */
+	sys	sys_mips_mmap2		6	/* 4210 */
 	sys	sys_truncate64		4
 	sys	sys_ftruncate64		4
 	sys	sys_stat64		2

arch/mips/kernel/scall64-64.S

@@ -207,7 +207,7 @@ sys_call_table:
 	PTR	sys_newlstat
 	PTR	sys_poll
 	PTR	sys_lseek
-	PTR	old_mmap
+	PTR	sys_mips_mmap
 	PTR	sys_mprotect			/* 5010 */
 	PTR	sys_munmap
 	PTR	sys_brk

arch/mips/kernel/scall64-n32.S

@@ -129,12 +129,12 @@ EXPORT(sysn32_call_table)
 	PTR	sys_newlstat
 	PTR	sys_poll
 	PTR	sys_lseek
-	PTR	old_mmap
+	PTR	sys_mips_mmap
 	PTR	sys_mprotect			/* 6010 */
 	PTR	sys_munmap
 	PTR	sys_brk
-	PTR	sys32_rt_sigaction
-	PTR	sys32_rt_sigprocmask
+	PTR	sys_32_rt_sigaction
+	PTR	sys_32_rt_sigprocmask
 	PTR	compat_sys_ioctl		/* 6015 */
 	PTR	sys_pread64
 	PTR	sys_pwrite64
@@ -159,7 +159,7 @@ EXPORT(sysn32_call_table)
 	PTR	compat_sys_setitimer
 	PTR	sys_alarm
 	PTR	sys_getpid
-	PTR	sys32_sendfile
+	PTR	sys_32_sendfile
 	PTR	sys_socket			/* 6040 */
 	PTR	sys_connect
 	PTR	sys_accept
@@ -181,14 +181,14 @@ EXPORT(sysn32_call_table)
 	PTR	sys_exit
 	PTR	compat_sys_wait4
 	PTR	sys_kill			/* 6060 */
-	PTR	sys32_newuname
+	PTR	sys_32_newuname
 	PTR	sys_semget
 	PTR	sys_semop
-	PTR	sysn32_semctl
+	PTR	sys_n32_semctl
 	PTR	sys_shmdt			/* 6065 */
 	PTR	sys_msgget
-	PTR	sysn32_msgsnd
-	PTR	sysn32_msgrcv
+	PTR	sys_n32_msgsnd
+	PTR	sys_n32_msgrcv
 	PTR	compat_sys_msgctl
 	PTR	compat_sys_fcntl		/* 6070 */
 	PTR	sys_flock
@@ -245,15 +245,15 @@ EXPORT(sysn32_call_table)
 	PTR	sys_getsid
 	PTR	sys_capget
 	PTR	sys_capset
-	PTR	sys32_rt_sigpending		/* 6125 */
+	PTR	sys_32_rt_sigpending		/* 6125 */
 	PTR	compat_sys_rt_sigtimedwait
-	PTR	sys32_rt_sigqueueinfo
+	PTR	sys_32_rt_sigqueueinfo
 	PTR	sysn32_rt_sigsuspend
 	PTR	sys32_sigaltstack
 	PTR	compat_sys_utime		/* 6130 */
 	PTR	sys_mknod
-	PTR	sys32_personality
-	PTR	sys32_ustat
+	PTR	sys_32_personality
+	PTR	sys_32_ustat
 	PTR	compat_sys_statfs
 	PTR	compat_sys_fstatfs		/* 6135 */
 	PTR	sys_sysfs
@@ -265,14 +265,14 @@ EXPORT(sysn32_call_table)
 	PTR	sys_sched_getscheduler
 	PTR	sys_sched_get_priority_max
 	PTR	sys_sched_get_priority_min
-	PTR	sys32_sched_rr_get_interval	/* 6145 */
+	PTR	sys_32_sched_rr_get_interval	/* 6145 */
 	PTR	sys_mlock
 	PTR	sys_munlock
 	PTR	sys_mlockall
 	PTR	sys_munlockall
 	PTR	sys_vhangup			/* 6150 */
 	PTR	sys_pivot_root
-	PTR	sys32_sysctl
+	PTR	sys_32_sysctl
 	PTR	sys_prctl
 	PTR	compat_sys_adjtimex
 	PTR	compat_sys_setrlimit		/* 6155 */

arch/mips/kernel/scall64-o32.S

@@ -265,12 +265,12 @@ sys_call_table:
 	PTR	sys_olduname
 	PTR	sys_umask			/* 4060 */
 	PTR	sys_chroot
-	PTR	sys32_ustat
+	PTR	sys_32_ustat
 	PTR	sys_dup2
 	PTR	sys_getppid
 	PTR	sys_getpgrp			/* 4065 */
 	PTR	sys_setsid
-	PTR	sys32_sigaction
+	PTR	sys_32_sigaction
 	PTR	sys_sgetmask
 	PTR	sys_ssetmask
 	PTR	sys_setreuid			/* 4070 */
@@ -293,7 +293,7 @@ sys_call_table:
 	PTR	sys_swapon
 	PTR	sys_reboot
 	PTR	compat_sys_old_readdir
-	PTR	old_mmap			/* 4090 */
+	PTR	sys_mips_mmap			/* 4090 */
 	PTR	sys_munmap
 	PTR	sys_truncate
 	PTR	sys_ftruncate
@@ -320,12 +320,12 @@ sys_call_table:
 	PTR	compat_sys_wait4
 	PTR	sys_swapoff			/* 4115 */
 	PTR	compat_sys_sysinfo
-	PTR	sys32_ipc
+	PTR	sys_32_ipc
 	PTR	sys_fsync
 	PTR	sys32_sigreturn
 	PTR	sys32_clone			/* 4120 */
 	PTR	sys_setdomainname
-	PTR	sys32_newuname
+	PTR	sys_32_newuname
 	PTR	sys_ni_syscall			/* sys_modify_ldt */
 	PTR	compat_sys_adjtimex
 	PTR	sys_mprotect			/* 4125 */
@@ -339,11 +339,11 @@ sys_call_table:
 	PTR	sys_fchdir
 	PTR	sys_bdflush
 	PTR	sys_sysfs			/* 4135 */
-	PTR	sys32_personality
+	PTR	sys_32_personality
 	PTR	sys_ni_syscall	 		/* for afs_syscall */
 	PTR	sys_setfsuid
 	PTR	sys_setfsgid
-	PTR	sys32_llseek			/* 4140 */
+	PTR	sys_32_llseek			/* 4140 */
 	PTR	compat_sys_getdents
 	PTR	compat_sys_select
 	PTR	sys_flock
@@ -356,7 +356,7 @@ sys_call_table:
 	PTR	sys_ni_syscall			/* 4150 */
 	PTR	sys_getsid
 	PTR	sys_fdatasync
-	PTR	sys32_sysctl
+	PTR	sys_32_sysctl
 	PTR	sys_mlock
 	PTR	sys_munlock			/* 4155 */
 	PTR	sys_mlockall
@@ -368,7 +368,7 @@ sys_call_table:
 	PTR	sys_sched_yield
 	PTR	sys_sched_get_priority_max
 	PTR	sys_sched_get_priority_min
-	PTR	sys32_sched_rr_get_interval 	/* 4165 */
+	PTR	sys_32_sched_rr_get_interval 	/* 4165 */
 	PTR	compat_sys_nanosleep
 	PTR	sys_mremap
 	PTR	sys_accept
@@ -397,25 +397,25 @@ sys_call_table:
 	PTR	sys_getresgid
 	PTR	sys_prctl
 	PTR	sys32_rt_sigreturn
-	PTR	sys32_rt_sigaction
-	PTR	sys32_rt_sigprocmask 		/* 4195 */
-	PTR	sys32_rt_sigpending
+	PTR	sys_32_rt_sigaction
+	PTR	sys_32_rt_sigprocmask 		/* 4195 */
+	PTR	sys_32_rt_sigpending
 	PTR	compat_sys_rt_sigtimedwait
-	PTR	sys32_rt_sigqueueinfo
+	PTR	sys_32_rt_sigqueueinfo
 	PTR	sys32_rt_sigsuspend
-	PTR	sys32_pread			/* 4200 */
-	PTR	sys32_pwrite
+	PTR	sys_32_pread			/* 4200 */
+	PTR	sys_32_pwrite
 	PTR	sys_chown
 	PTR	sys_getcwd
 	PTR	sys_capget
 	PTR	sys_capset			/* 4205 */
 	PTR	sys32_sigaltstack
-	PTR	sys32_sendfile
+	PTR	sys_32_sendfile
 	PTR	sys_ni_syscall
 	PTR	sys_ni_syscall
-	PTR	sys32_mmap2			/* 4210 */
-	PTR	sys32_truncate64
-	PTR	sys32_ftruncate64
+	PTR	sys_mips_mmap2			/* 4210 */
+	PTR	sys_32_truncate64
+	PTR	sys_32_ftruncate64
 	PTR	sys_newstat
 	PTR	sys_newlstat
 	PTR	sys_newfstat			/* 4215 */
@@ -481,7 +481,7 @@ sys_call_table:
 	PTR	compat_sys_mq_notify		/* 4275 */
 	PTR	compat_sys_mq_getsetattr
 	PTR	sys_ni_syscall			/* sys_vserver */
-	PTR	sys32_waitid
+	PTR	sys_32_waitid
 	PTR	sys_ni_syscall			/* available, was setaltroot */
 	PTR	sys_add_key			/* 4280 */
 	PTR	sys_request_key

arch/mips/kernel/signal.c

@@ -19,6 +19,7 @@
 #include <linux/ptrace.h>
 #include <linux/unistd.h>
 #include <linux/compiler.h>
+#include <linux/syscalls.h>
 #include <linux/uaccess.h>
 
 #include <asm/abi.h>
@@ -338,8 +339,8 @@ asmlinkage int sys_rt_sigsuspend(nabi_no_regargs struct pt_regs regs)
 }
 
 #ifdef CONFIG_TRAD_SIGNALS
-asmlinkage int sys_sigaction(int sig, const struct sigaction __user *act,
-	struct sigaction __user *oact)
+SYSCALL_DEFINE3(sigaction, int, sig, const struct sigaction __user *, act,
+	struct sigaction __user *, oact)
 {
 	struct k_sigaction new_ka, old_ka;
 	int ret;

arch/mips/kernel/signal32.c

@@ -349,8 +349,8 @@ asmlinkage int sys32_rt_sigsuspend(nabi_no_regargs struct pt_regs regs)
 	return -ERESTARTNOHAND;
 }
 
-asmlinkage int sys32_sigaction(int sig, const struct sigaction32 __user *act,
-                               struct sigaction32 __user *oact)
+SYSCALL_DEFINE3(32_sigaction, long, sig, const struct sigaction32 __user *, act,
+	struct sigaction32 __user *, oact)
 {
 	struct k_sigaction new_ka, old_ka;
 	int ret;
@@ -704,9 +704,9 @@ struct mips_abi mips_abi_32 = {
 	.restart	= __NR_O32_restart_syscall
 };
 
-asmlinkage int sys32_rt_sigaction(int sig, const struct sigaction32 __user *act,
-				  struct sigaction32 __user *oact,
-				  unsigned int sigsetsize)
+SYSCALL_DEFINE4(32_rt_sigaction, int, sig,
+	const struct sigaction32 __user *, act,
+	struct sigaction32 __user *, oact, unsigned int, sigsetsize)
 {
 	struct k_sigaction new_sa, old_sa;
 	int ret = -EINVAL;
@@ -748,8 +748,8 @@ out:
 	return ret;
 }
 
-asmlinkage int sys32_rt_sigprocmask(int how, compat_sigset_t __user *set,
-	compat_sigset_t __user *oset, unsigned int sigsetsize)
+SYSCALL_DEFINE4(32_rt_sigprocmask, int, how, compat_sigset_t __user *, set,
+	compat_sigset_t __user *, oset, unsigned int, sigsetsize)
 {
 	sigset_t old_set, new_set;
 	int ret;
@@ -770,8 +770,8 @@ asmlinkage int sys32_rt_sigprocmask(int how, compat_sigset_t __user *set,
 	return ret;
 }
 
-asmlinkage int sys32_rt_sigpending(compat_sigset_t __user *uset,
-	unsigned int sigsetsize)
+SYSCALL_DEFINE2(32_rt_sigpending, compat_sigset_t __user *, uset,
+	unsigned int, sigsetsize)
 {
 	int ret;
 	sigset_t set;
@@ -787,7 +787,8 @@ asmlinkage int sys32_rt_sigpending(compat_sigset_t __user *uset,
 	return ret;
 }
 
-asmlinkage int sys32_rt_sigqueueinfo(int pid, int sig, compat_siginfo_t __user *uinfo)
+SYSCALL_DEFINE3(32_rt_sigqueueinfo, int, pid, int, sig,
+	compat_siginfo_t __user *, uinfo)
 {
 	siginfo_t info;
 	int ret;
@@ -802,10 +803,9 @@ asmlinkage int sys32_rt_sigqueueinfo(int pid, int sig, compat_siginfo_t __user *
 	return ret;
 }
 
-asmlinkage long
-sys32_waitid(int which, compat_pid_t pid,
-	     compat_siginfo_t __user *uinfo, int options,
-	     struct compat_rusage __user *uru)
+SYSCALL_DEFINE5(32_waitid, int, which, compat_pid_t, pid,
+	     compat_siginfo_t __user *, uinfo, int, options,
+	     struct compat_rusage __user *, uru)
 {
 	siginfo_t info;
 	struct rusage ru;

arch/mips/kernel/syscall.c

@@ -152,9 +152,9 @@ out:
 	return error;
 }
 
-asmlinkage unsigned long
-old_mmap(unsigned long addr, unsigned long len, int prot,
-	int flags, int fd, off_t offset)
+SYSCALL_DEFINE6(mips_mmap, unsigned long, addr, unsigned long, len,
+	unsigned long, prot, unsigned long, flags, unsigned long,
+	fd, off_t, offset)
 {
 	unsigned long result;
 
@@ -168,9 +168,9 @@ out:
 	return result;
 }
 
-asmlinkage unsigned long
-sys_mmap2(unsigned long addr, unsigned long len, unsigned long prot,
-          unsigned long flags, unsigned long fd, unsigned long pgoff)
+SYSCALL_DEFINE6(mips_mmap2, unsigned long, addr, unsigned long, len,
+	unsigned long, prot, unsigned long, flags, unsigned long, fd,
+	unsigned long, pgoff)
 {
 	if (pgoff & (~PAGE_MASK >> 12))
 		return -EINVAL;
@@ -240,7 +240,7 @@ out:
 /*
  * Compacrapability ...
  */
-asmlinkage int sys_uname(struct old_utsname __user * name)
+SYSCALL_DEFINE1(uname, struct old_utsname __user *, name)
 {
 	if (name && !copy_to_user(name, utsname(), sizeof (*name)))
 		return 0;
@@ -250,7 +250,7 @@ asmlinkage int sys_uname(struct old_utsname __user * name)
 /*
  * Compacrapability ...
  */
-asmlinkage int sys_olduname(struct oldold_utsname __user * name)
+SYSCALL_DEFINE1(olduname, struct oldold_utsname __user *, name)
 {
 	int error;
 
@@ -279,7 +279,7 @@ asmlinkage int sys_olduname(struct oldold_utsname __user * name)
 	return error;
 }
 
-asmlinkage int sys_set_thread_area(unsigned long addr)
+SYSCALL_DEFINE1(set_thread_area, unsigned long, addr)
 {
 	struct thread_info *ti = task_thread_info(current);
 
@@ -290,7 +290,7 @@ asmlinkage int sys_set_thread_area(unsigned long addr)
 	return 0;
 }
 
-asmlinkage int _sys_sysmips(int cmd, long arg1, int arg2, int arg3)
+asmlinkage int _sys_sysmips(long cmd, long arg1, long arg2, long arg3)
 {
 	switch (cmd) {
 	case MIPS_ATOMIC_SET:
@@ -325,8 +325,8 @@ asmlinkage int _sys_sysmips(int cmd, long arg1, int arg2, int arg3)
  *
  * This is really horribly ugly.
  */
-asmlinkage int sys_ipc(unsigned int call, int first, int second,
-		       unsigned long third, void __user *ptr, long fifth)
+SYSCALL_DEFINE6(ipc, unsigned int, call, int, first, int, second,
+	unsigned long, third, void __user *, ptr, long, fifth)
 {
 	int version, ret;
 
@@ -411,7 +411,7 @@ asmlinkage int sys_ipc(unsigned int call, int first, int second,
 /*
  * No implemented yet ...
  */
-asmlinkage int sys_cachectl(char *addr, int nbytes, int op)
+SYSCALL_DEFINE3(cachectl, char *, addr, int, nbytes, int, op)
 {
 	return -ENOSYS;
 }

arch/mips/mm/cache.c

@@ -13,6 +13,7 @@
 #include <linux/linkage.h>
 #include <linux/module.h>
 #include <linux/sched.h>
+#include <linux/syscalls.h>
 #include <linux/mm.h>
 
 #include <asm/cacheflush.h>
@@ -58,8 +59,8 @@ EXPORT_SYMBOL(_dma_cache_wback_inv);
  * We could optimize the case where the cache argument is not BCACHE but
  * that seems very atypical use ...
  */
-asmlinkage int sys_cacheflush(unsigned long addr,
-	unsigned long bytes, unsigned int cache)
+SYSCALL_DEFINE3(cacheflush, unsigned long, addr, unsigned long, bytes,
+	unsigned int, cache)
 {
 	if (bytes == 0)
 		return 0;

arch/mn10300/Kconfig

@@ -7,6 +7,7 @@ mainmenu "Linux Kernel Configuration"
 
 config MN10300
 	def_bool y
+	select HAVE_OPROFILE
 
 config AM33
 	def_bool y

arch/mn10300/unit-asb2305/pci.c

@@ -173,7 +173,7 @@ static int pci_ampci_write_config_byte(struct pci_bus *bus, unsigned int devfn,
 		BRIDGEREGB(where) = value;
 	} else {
 		if (bus->number == 0 &&
-		    (devfn == PCI_DEVFN(2, 0) && devfn == PCI_DEVFN(3, 0))
+		    (devfn == PCI_DEVFN(2, 0) || devfn == PCI_DEVFN(3, 0))
 		    )
 			__pcidebug("<= %02x", bus, devfn, where, value);
 		CONFIG_ADDRESS = CONFIG_CMD(bus, devfn, where);

arch/powerpc/include/asm/compat.h

@@ -210,5 +210,10 @@ struct compat_shmid64_ds {
 	compat_ulong_t __unused6;
 };
 
+static inline int is_compat_task(void)
+{
+	return test_thread_flag(TIF_32BIT);
+}
+
 #endif /* __KERNEL__ */
 #endif /* _ASM_POWERPC_COMPAT_H */

arch/powerpc/include/asm/seccomp.h

@@ -1,10 +1,6 @@
 #ifndef _ASM_POWERPC_SECCOMP_H
 #define _ASM_POWERPC_SECCOMP_H
 
-#ifdef __KERNEL__
-#include <linux/thread_info.h>
-#endif
-
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

arch/powerpc/kernel/align.c

@@ -367,27 +367,24 @@ static int emulate_multiple(struct pt_regs *regs, unsigned char __user *addr,
 static int emulate_fp_pair(unsigned char __user *addr, unsigned int reg,
 			   unsigned int flags)
 {
-	char *ptr = (char *) &current->thread.TS_FPR(reg);
-	int i, ret;
+	char *ptr0 = (char *) &current->thread.TS_FPR(reg);
+	char *ptr1 = (char *) &current->thread.TS_FPR(reg+1);
+	int i, ret, sw = 0;
 
 	if (!(flags & F))
 		return 0;
 	if (reg & 1)
 		return 0;	/* invalid form: FRS/FRT must be even */
-	if (!(flags & SW)) {
-		/* not byte-swapped - easy */
-		if (!(flags & ST))
-			ret = __copy_from_user(ptr, addr, 16);
-		else
-			ret = __copy_to_user(addr, ptr, 16);
-	} else {
-		/* each FPR value is byte-swapped separately */
-		ret = 0;
-		for (i = 0; i < 16; ++i) {
-			if (!(flags & ST))
-				ret |= __get_user(ptr[i^7], addr + i);
-			else
-				ret |= __put_user(ptr[i^7], addr + i);
+	if (flags & SW)
+		sw = 7;
+	ret = 0;
+	for (i = 0; i < 8; ++i) {
+		if (!(flags & ST)) {
+			ret |= __get_user(ptr0[i^sw], addr + i);
+			ret |= __get_user(ptr1[i^sw], addr + i + 8);
+		} else {
+			ret |= __put_user(ptr0[i^sw], addr + i);
+			ret |= __put_user(ptr1[i^sw], addr + i + 8);
 		}
 	}
 	if (ret)

arch/powerpc/lib/copyuser_64.S

@@ -62,18 +62,19 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 72:	std	r8,8(r3)
 	beq+	3f
 	addi	r3,r3,16
-23:	ld	r9,8(r4)
 .Ldo_tail:
 	bf	cr7*4+1,1f
-	rotldi	r9,r9,32
+23:	lwz	r9,8(r4)
+	addi	r4,r4,4
 73:	stw	r9,0(r3)
 	addi	r3,r3,4
 1:	bf	cr7*4+2,2f
-	rotldi	r9,r9,16
+44:	lhz	r9,8(r4)
+	addi	r4,r4,2
 74:	sth	r9,0(r3)
 	addi	r3,r3,2
 2:	bf	cr7*4+3,3f
-	rotldi	r9,r9,8
+45:	lbz	r9,8(r4)
 75:	stb	r9,0(r3)
 3:	li	r3,0
 	blr
@@ -141,11 +142,24 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 6:	cmpwi	cr1,r5,8
 	addi	r3,r3,32
 	sld	r9,r9,r10
-	ble	cr1,.Ldo_tail
+	ble	cr1,7f
 34:	ld	r0,8(r4)
 	srd	r7,r0,r11
 	or	r9,r7,r9
-	b	.Ldo_tail
+7:
+	bf	cr7*4+1,1f
+	rotldi	r9,r9,32
+94:	stw	r9,0(r3)
+	addi	r3,r3,4
+1:	bf	cr7*4+2,2f
+	rotldi	r9,r9,16
+95:	sth	r9,0(r3)
+	addi	r3,r3,2
+2:	bf	cr7*4+3,3f
+	rotldi	r9,r9,8
+96:	stb	r9,0(r3)
+3:	li	r3,0
+	blr
 
 .Ldst_unaligned:
 	PPC_MTOCRF	0x01,r6		/* put #bytes to 8B bdry into cr7 */
@@ -218,7 +232,6 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 121:
 132:
 	addi	r3,r3,8
-123:
 134:
 135:
 138:
@@ -226,6 +239,9 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 140:
 141:
 142:
+123:
+144:
+145:
 
 /*
  * here we have had a fault on a load and r3 points to the first
@@ -309,6 +325,9 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 187:
 188:
 189:	
+194:
+195:
+196:
 1:
 	ld	r6,-24(r1)
 	ld	r5,-8(r1)
@@ -329,7 +348,9 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 	.llong	72b,172b
 	.llong	23b,123b
 	.llong	73b,173b
+	.llong	44b,144b
 	.llong	74b,174b
+	.llong	45b,145b
 	.llong	75b,175b
 	.llong	24b,124b
 	.llong	25b,125b
@@ -347,6 +368,9 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 	.llong	79b,179b
 	.llong	80b,180b
 	.llong	34b,134b
+	.llong	94b,194b
+	.llong	95b,195b
+	.llong	96b,196b
 	.llong	35b,135b
 	.llong	81b,181b
 	.llong	36b,136b

arch/powerpc/lib/memcpy_64.S

@@ -53,18 +53,19 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 3:	std	r8,8(r3)
 	beq	3f
 	addi	r3,r3,16
-	ld	r9,8(r4)
 .Ldo_tail:
 	bf	cr7*4+1,1f
-	rotldi	r9,r9,32
+	lwz	r9,8(r4)
+	addi	r4,r4,4
 	stw	r9,0(r3)
 	addi	r3,r3,4
 1:	bf	cr7*4+2,2f
-	rotldi	r9,r9,16
+	lhz	r9,8(r4)
+	addi	r4,r4,2
 	sth	r9,0(r3)
 	addi	r3,r3,2
 2:	bf	cr7*4+3,3f
-	rotldi	r9,r9,8
+	lbz	r9,8(r4)
 	stb	r9,0(r3)
 3:	ld	r3,48(r1)	/* return dest pointer */
 	blr
@@ -133,11 +134,24 @@ END_FTR_SECTION_IFCLR(CPU_FTR_UNALIGNED_LD_STD)
 	cmpwi	cr1,r5,8
 	addi	r3,r3,32
 	sld	r9,r9,r10
-	ble	cr1,.Ldo_tail
+	ble	cr1,6f
 	ld	r0,8(r4)
 	srd	r7,r0,r11
 	or	r9,r7,r9
-	b	.Ldo_tail
+6:
+	bf	cr7*4+1,1f
+	rotldi	r9,r9,32
+	stw	r9,0(r3)
+	addi	r3,r3,4
+1:	bf	cr7*4+2,2f
+	rotldi	r9,r9,16
+	sth	r9,0(r3)
+	addi	r3,r3,2
+2:	bf	cr7*4+3,3f
+	rotldi	r9,r9,8
+	stb	r9,0(r3)
+3:	ld	r3,48(r1)	/* return dest pointer */
+	blr
 
 .Ldst_unaligned:
 	PPC_MTOCRF	0x01,r6		# put #bytes to 8B bdry into cr7

arch/powerpc/sysdev/ppc4xx_pci.c

@@ -204,6 +204,23 @@ static int __init ppc4xx_setup_one_pci_PMM(struct pci_controller	*hose,
 {
 	u32 ma, pcila, pciha;
 
+	/* Hack warning ! The "old" PCI 2.x cell only let us configure the low
+	 * 32-bit of incoming PLB addresses. The top 4 bits of the 36-bit
+	 * address are actually hard wired to a value that appears to depend
+	 * on the specific SoC. For example, it's 0 on 440EP and 1 on 440EPx.
+	 *
+	 * The trick here is we just crop those top bits and ignore them when
+	 * programming the chip. That means the device-tree has to be right
+	 * for the specific part used (we don't print a warning if it's wrong
+	 * but on the other hand, you'll crash quickly enough), but at least
+	 * this code should work whatever the hard coded value is
+	 */
+	plb_addr &= 0xffffffffull;
+
+	/* Note: Due to the above hack, the test below doesn't actually test
+	 * if you address is above 4G, but it tests that address and
+	 * (address + size) are both contained in the same 4G
+	 */
 	if ((plb_addr + size) > 0xffffffffull || !is_power_of_2(size) ||
 	    size < 0x1000 || (plb_addr & (size - 1)) != 0) {
 		printk(KERN_WARNING "%s: Resource out of range\n",

arch/s390/include/asm/cputime.h

@@ -145,7 +145,7 @@ cputime_to_timeval(const cputime_t cputime, struct timeval *value)
 	value->tv_usec = rp.subreg.even / 4096;
 	value->tv_sec = rp.subreg.odd;
 #else
-	value->tv_usec = cputime % 4096000000ULL;
+	value->tv_usec = (cputime % 4096000000ULL) / 4096;
 	value->tv_sec = cputime / 4096000000ULL;
 #endif
 }

arch/s390/include/asm/setup.h

@@ -43,6 +43,8 @@ struct mem_chunk {
 
 extern struct mem_chunk memory_chunk[];
 extern unsigned long real_memory_size;
+extern int memory_end_set;
+extern unsigned long memory_end;
 
 void detect_memory_layout(struct mem_chunk chunk[]);
 

arch/s390/kernel/setup.c

@@ -82,7 +82,9 @@ char elf_platform[ELF_PLATFORM_SIZE];
 
 struct mem_chunk __initdata memory_chunk[MEMORY_CHUNKS];
 volatile int __cpu_logical_map[NR_CPUS]; /* logical cpu to cpu address */
-static unsigned long __initdata memory_end;
+
+int __initdata memory_end_set;
+unsigned long __initdata memory_end;
 
 /*
  * This is set up by the setup-routine at boot-time
@@ -281,6 +283,7 @@ void (*pm_power_off)(void) = machine_power_off;
 static int __init early_parse_mem(char *p)
 {
 	memory_end = memparse(p, &p);
+	memory_end_set = 1;
 	return 0;
 }
 early_param("mem", early_parse_mem);
@@ -508,8 +511,10 @@ static void __init setup_memory_end(void)
 	int i;
 
 #if defined(CONFIG_ZFCPDUMP) || defined(CONFIG_ZFCPDUMP_MODULE)
-	if (ipl_info.type == IPL_TYPE_FCP_DUMP)
+	if (ipl_info.type == IPL_TYPE_FCP_DUMP) {
 		memory_end = ZFCPDUMP_HSA_SIZE;
+		memory_end_set = 1;
+	}
 #endif
 	memory_size = 0;
 	memory_end &= PAGE_MASK;

arch/sh/boards/board-ap325rxa.c

@@ -22,7 +22,6 @@
 #include <linux/gpio.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi_gpio.h>
-#include <media/ov772x.h>
 #include <media/soc_camera_platform.h>
 #include <media/sh_mobile_ceu.h>
 #include <video/sh_mobile_lcdc.h>
@@ -224,7 +223,6 @@ static void camera_power(int val)
 }
 
 #ifdef CONFIG_I2C
-/* support for the old ncm03j camera */
 static unsigned char camera_ncm03j_magic[] =
 {
 	0x87, 0x00, 0x88, 0x08, 0x89, 0x01, 0x8A, 0xE8,
@@ -245,23 +243,6 @@ static unsigned char camera_ncm03j_magic[] =
 	0x63, 0xD4, 0x64, 0xEA, 0xD6, 0x0F,
 };
 
-static int camera_probe(void)
-{
-	struct i2c_adapter *a = i2c_get_adapter(0);
-	struct i2c_msg msg;
-	int ret;
-
-	camera_power(1);
-	msg.addr = 0x6e;
-	msg.buf = camera_ncm03j_magic;
-	msg.len = 2;
-	msg.flags = 0;
-	ret = i2c_transfer(a, &msg, 1);
-	camera_power(0);
-
-	return ret;
-}
-
 static int camera_set_capture(struct soc_camera_platform_info *info,
 			      int enable)
 {
@@ -313,35 +294,8 @@ static struct platform_device camera_device = {
 		.platform_data	= &camera_info,
 	},
 };
-
-static int __init camera_setup(void)
-{
-	if (camera_probe() > 0)
-		platform_device_register(&camera_device);
-
-	return 0;
-}
-late_initcall(camera_setup);
-
 #endif /* CONFIG_I2C */
 
-static int ov7725_power(struct device *dev, int mode)
-{
-	camera_power(0);
-	if (mode)
-		camera_power(1);
-
-	return 0;
-}
-
-static struct ov772x_camera_info ov7725_info = {
-	.buswidth  = SOCAM_DATAWIDTH_8,
-	.flags = OV772X_FLAG_VFLIP | OV772X_FLAG_HFLIP,
-	.link = {
-		.power  = ov7725_power,
-	},
-};
-
 static struct sh_mobile_ceu_info sh_mobile_ceu_info = {
 	.flags = SOCAM_PCLK_SAMPLE_RISING | SOCAM_HSYNC_ACTIVE_HIGH |
 	SOCAM_VSYNC_ACTIVE_HIGH | SOCAM_MASTER | SOCAM_DATAWIDTH_8,
@@ -392,6 +346,9 @@ static struct platform_device *ap325rxa_devices[] __initdata = {
 	&ap325rxa_nor_flash_device,
 	&lcdc_device,
 	&ceu_device,
+#ifdef CONFIG_I2C
+	&camera_device,
+#endif
 	&nand_flash_device,
 	&sdcard_cn3_device,
 };
@@ -400,10 +357,6 @@ static struct i2c_board_info __initdata ap325rxa_i2c_devices[] = {
 	{
 		I2C_BOARD_INFO("pcf8563", 0x51),
 	},
-	{
-		I2C_BOARD_INFO("ov772x", 0x21),
-		.platform_data = &ov7725_info,
-	},
 };
 
 static struct spi_board_info ap325rxa_spi_devices[] = {

arch/sh/kernel/cpu/sh2a/clock-sh7201.c

@@ -18,8 +18,8 @@
 #include <asm/freq.h>
 #include <asm/io.h>
 
-const static int pll1rate[]={1,2,3,4,6,8};
-const static int pfc_divisors[]={1,2,3,4,6,8,12};
+static const int pll1rate[]={1,2,3,4,6,8};
+static const int pfc_divisors[]={1,2,3,4,6,8,12};
 #define ifc_divisors pfc_divisors
 
 #if (CONFIG_SH_CLK_MD == 0)

arch/sparc/include/asm/compat.h

@@ -240,4 +240,9 @@ struct compat_shmid64_ds {
 	unsigned int	__unused2;
 };
 
+static inline int is_compat_task(void)
+{
+	return test_thread_flag(TIF_32BIT);
+}
+
 #endif /* _ASM_SPARC64_COMPAT_H */

arch/sparc/include/asm/seccomp.h

@@ -1,11 +1,5 @@
 #ifndef _ASM_SECCOMP_H
 
-#include <linux/thread_info.h> /* already defines TIF_32BIT */
-
-#ifndef TIF_32BIT
-#error "unexpected TIF_32BIT on sparc64"
-#endif
-
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

arch/sparc/kernel/chmc.c

@@ -306,6 +306,7 @@ static int jbusmc_print_dimm(int syndrome_code,
 		buf[1] = '?';
 		buf[2] = '?';
 		buf[3] = '\0';
+		return 0;
 	}
 	p = dp->controller;
 	prop = &p->layout;

arch/um/drivers/vde_user.c

@@ -78,7 +78,7 @@ void vde_init_libstuff(struct vde_data *vpri, struct vde_init *init)
 {
 	struct vde_open_args *args;
 
-	vpri->args = kmalloc(sizeof(struct vde_open_args), UM_GFP_KERNEL);
+	vpri->args = uml_kmalloc(sizeof(struct vde_open_args), UM_GFP_KERNEL);
 	if (vpri->args == NULL) {
 		printk(UM_KERN_ERR "vde_init_libstuff - vde_open_args "
 		       "allocation failed");
@@ -91,8 +91,8 @@ void vde_init_libstuff(struct vde_data *vpri, struct vde_init *init)
 	args->group = init->group;
 	args->mode = init->mode ? init->mode : 0700;
 
-	args->port ?  printk(UM_KERN_INFO "port %d", args->port) :
-		printk(UM_KERN_INFO "undefined port");
+	args->port ?  printk("port %d", args->port) :
+		printk("undefined port");
 }
 
 int vde_user_read(void *conn, void *buf, int len)

arch/x86/Kconfig

@@ -1803,7 +1803,7 @@ config DMAR
 	  remapping devices.
 
 config DMAR_DEFAULT_ON
-	def_bool n
+	def_bool y
 	prompt "Enable DMA Remapping Devices by default"
 	depends on DMAR
 	help

arch/x86/include/asm/iomap.h

@@ -23,6 +23,9 @@
 #include <asm/pgtable.h>
 #include <asm/tlbflush.h>
 
+int
+is_io_mapping_possible(resource_size_t base, unsigned long size);
+
 void *
 iomap_atomic_prot_pfn(unsigned long pfn, enum km_type type, pgprot_t prot);
 

arch/x86/include/asm/mmzone_32.h

@@ -32,8 +32,6 @@ static inline void get_memcfg_numa(void)
 	get_memcfg_numa_flat();
 }
 
-extern int early_pfn_to_nid(unsigned long pfn);
-
 extern void resume_map_numa_kva(pgd_t *pgd);
 
 #else /* !CONFIG_NUMA */

arch/x86/include/asm/mmzone_64.h

@@ -40,8 +40,6 @@ static inline __attribute__((pure)) int phys_to_nid(unsigned long addr)
 #define node_end_pfn(nid)       (NODE_DATA(nid)->node_start_pfn +	\
 				 NODE_DATA(nid)->node_spanned_pages)
 
-extern int early_pfn_to_nid(unsigned long pfn);
-
 #ifdef CONFIG_NUMA_EMU
 #define FAKE_NODE_MIN_SIZE	(64 * 1024 * 1024)
 #define FAKE_NODE_MIN_HASH_MASK	(~(FAKE_NODE_MIN_SIZE - 1UL))

arch/x86/include/asm/seccomp_32.h

@@ -1,12 +1,6 @@
 #ifndef _ASM_X86_SECCOMP_32_H
 #define _ASM_X86_SECCOMP_32_H
 
-#include <linux/thread_info.h>
-
-#ifdef TIF_32BIT
-#error "unexpected TIF_32BIT on i386"
-#endif
-
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

arch/x86/include/asm/seccomp_64.h

@@ -1,14 +1,6 @@
 #ifndef _ASM_X86_SECCOMP_64_H
 #define _ASM_X86_SECCOMP_64_H
 
-#include <linux/thread_info.h>
-
-#ifdef TIF_32BIT
-#error "unexpected TIF_32BIT on x86_64"
-#else
-#define TIF_32BIT TIF_IA32
-#endif
-
 #include <linux/unistd.h>
 #include <asm/ia32_unistd.h>