Merge branch 'mxs/boards' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/boards

* 'mxs/boards' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: Add initial support for Bluegiga APX4 Development Kit
  ARM: mxs: read correct values when setting up MAC
  ARM: mx28evk: Simplify GPIO requests
  ARM: mx28: Remove duplicate OCOTP error message
  ARM: mxs: detect SoC by checking CHIPID register

arch/arm/mach-mxs/Kconfig

@@ -83,6 +83,18 @@ config MODULE_M28
 	select MXS_HAVE_PLATFORM_MXSFB
 	select MXS_OCOTP
 
+config MODULE_APX4
+	bool
+	select SOC_IMX28
+	select LEDS_GPIO_REGISTER
+	select MXS_HAVE_AMBA_DUART
+	select MXS_HAVE_PLATFORM_AUART
+	select MXS_HAVE_PLATFORM_FEC
+	select MXS_HAVE_PLATFORM_MXS_I2C
+	select MXS_HAVE_PLATFORM_MXS_MMC
+	select MXS_HAVE_PLATFORM_MXS_SAIF
+	select MXS_OCOTP
+
 config MACH_TX28
 	bool "Ka-Ro TX28 module"
 	select MODULE_TX28
@@ -91,4 +103,8 @@ config MACH_M28EVK
 	bool "Support DENX M28EVK Platform"
 	select MODULE_M28
 
+config MACH_APX4DEVKIT
+	bool "Support Bluegiga APX4 Development Kit"
+	select MODULE_APX4
+
 endif

arch/arm/mach-mxs/Makefile

@@ -11,6 +11,7 @@ obj-$(CONFIG_MACH_STMP378X_DEVB) += mach-stmp378x_devb.o
 obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
 obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
 obj-$(CONFIG_MACH_M28EVK)    += mach-m28evk.o
+obj-$(CONFIG_MACH_APX4DEVKIT) += mach-apx4devkit.o
 obj-$(CONFIG_MODULE_TX28) += module-tx28.o
 obj-$(CONFIG_MACH_TX28)    += mach-tx28.o
 

arch/arm/mach-mxs/include/mach/digctl.h

@@ -18,4 +18,5 @@
 #define HW_DIGCTL_CTRL			0x0
 #define  BP_DIGCTL_CTRL_SAIF_CLKMUX	10
 #define  BM_DIGCTL_CTRL_SAIF_CLKMUX	(0x3 << 10)
+#define HW_DIGCTL_CHIPID		0x310
 #endif

arch/arm/mach-mxs/include/mach/mxs.h

@@ -23,21 +23,9 @@
 #include <linux/io.h>
 #endif
 #include <asm/mach-types.h>
+#include <mach/digctl.h>
 #include <mach/hardware.h>
 
-/*
- * MXS CPU types
- */
-#define cpu_is_mx23()		(					\
-		machine_is_mx23evk() ||					\
-		machine_is_stmp378x() ||				\
-		0)
-#define cpu_is_mx28()		(					\
-		machine_is_mx28evk() ||					\
-		machine_is_m28evk() ||					\
-		machine_is_tx28() ||					\
-		0)
-
 /*
  * IO addresses common to MXS-based
  */
@@ -109,6 +97,21 @@ static inline void __mxs_togl(u32 mask, void __iomem *reg)
 {
 	__raw_writel(mask, reg + MXS_TOG_ADDR);
 }
+
+/*
+ * MXS CPU types
+ */
+#define MXS_CHIPID (MXS_IO_ADDRESS(MXS_DIGCTL_BASE_ADDR) + HW_DIGCTL_CHIPID)
+
+static inline int cpu_is_mx23(void)
+{
+	return ((__raw_readl(MXS_CHIPID) >> 16) == 0x3780);
+}
+
+static inline int cpu_is_mx28(void)
+{
+	return ((__raw_readl(MXS_CHIPID) >> 16) == 0x2800);
+}
 #endif
 
 #endif /* __MACH_MXS_H__ */

arch/arm/mach-mxs/include/mach/uncompress.h

@@ -18,8 +18,6 @@
 #ifndef __MACH_MXS_UNCOMPRESS_H__
 #define __MACH_MXS_UNCOMPRESS_H__
 
-#include <asm/mach-types.h>
-
 unsigned long mxs_duart_base;
 
 #define MXS_DUART(x)	(*(volatile unsigned long *)(mxs_duart_base + (x)))
@@ -55,16 +53,17 @@ static inline void flush(void)
 
 #define MX23_DUART_BASE_ADDR	0x80070000
 #define MX28_DUART_BASE_ADDR	0x80074000
+#define MXS_DIGCTL_CHIPID	0x8001c310
 
 static inline void __arch_decomp_setup(unsigned long arch_id)
 {
-	switch (arch_id) {
-	case MACH_TYPE_MX23EVK:
+	u16 chipid = (*(volatile unsigned long *) MXS_DIGCTL_CHIPID) >> 16;
+
+	switch (chipid) {
+	case 0x3780:
 		mxs_duart_base = MX23_DUART_BASE_ADDR;
 		break;
-	case MACH_TYPE_MX28EVK:
-	case MACH_TYPE_M28EVK:
-	case MACH_TYPE_TX28:
+	case 0x2800:
 		mxs_duart_base = MX28_DUART_BASE_ADDR;
 		break;
 	default:

arch/arm/mach-mxs/mach-apx4devkit.c

@@ -0,0 +1,260 @@
+/*
+ * Copyright (C) 2011-2012
+ * Lauri Hintsala, Bluegiga, <lauri.hintsala@bluegiga.com>
+ * Veli-Pekka Peltola, Bluegiga, <veli-pekka.peltola@bluegiga.com>
+ *
+ * based on: mach-mx28evk.c
+ * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/micrel_phy.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include <mach/common.h>
+#include <mach/digctl.h>
+#include <mach/iomux-mx28.h>
+
+#include "devices-mx28.h"
+
+#define APX4DEVKIT_GPIO_USERLED	MXS_GPIO_NR(3, 28)
+
+static const iomux_cfg_t apx4devkit_pads[] __initconst = {
+	/* duart */
+	MX28_PAD_PWM0__DUART_RX | MXS_PAD_CTRL,
+	MX28_PAD_PWM1__DUART_TX | MXS_PAD_CTRL,
+
+	/* auart0 */
+	MX28_PAD_AUART0_RX__AUART0_RX | MXS_PAD_CTRL,
+	MX28_PAD_AUART0_TX__AUART0_TX | MXS_PAD_CTRL,
+	MX28_PAD_AUART0_CTS__AUART0_CTS | MXS_PAD_CTRL,
+	MX28_PAD_AUART0_RTS__AUART0_RTS | MXS_PAD_CTRL,
+
+	/* auart1 */
+	MX28_PAD_AUART1_RX__AUART1_RX | MXS_PAD_CTRL,
+	MX28_PAD_AUART1_TX__AUART1_TX | MXS_PAD_CTRL,
+
+	/* auart2 */
+	MX28_PAD_SSP2_SCK__AUART2_RX | MXS_PAD_CTRL,
+	MX28_PAD_SSP2_MOSI__AUART2_TX | MXS_PAD_CTRL,
+
+	/* auart3 */
+	MX28_PAD_SSP2_MISO__AUART3_RX | MXS_PAD_CTRL,
+	MX28_PAD_SSP2_SS0__AUART3_TX | MXS_PAD_CTRL,
+
+#define MXS_PAD_FEC	(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP)
+	/* fec0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MXS_PAD_FEC,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MXS_PAD_FEC,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MXS_PAD_FEC,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MXS_PAD_FEC,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MXS_PAD_FEC,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MXS_PAD_FEC,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MXS_PAD_FEC,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MXS_PAD_FEC,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MXS_PAD_FEC,
+
+	/* i2c */
+	MX28_PAD_I2C0_SCL__I2C0_SCL,
+	MX28_PAD_I2C0_SDA__I2C0_SDA,
+
+	/* mmc0 */
+	MX28_PAD_SSP0_DATA0__SSP0_D0 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA1__SSP0_D1 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA2__SSP0_D2 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA3__SSP0_D3 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA4__SSP0_D4 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA5__SSP0_D5 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA6__SSP0_D6 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DATA7__SSP0_D7 |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_CMD__SSP0_CMD |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_SSP0_SCK__SSP0_SCK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+
+	/* led */
+	MX28_PAD_PWM3__GPIO_3_28 | MXS_PAD_CTRL,
+
+	/* saif0 & saif1 */
+	MX28_PAD_SAIF0_MCLK__SAIF0_MCLK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+	MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+};
+
+/* led */
+static const struct gpio_led apx4devkit_leds[] __initconst = {
+	{
+		.name = "user-led",
+		.default_trigger = "heartbeat",
+		.gpio = APX4DEVKIT_GPIO_USERLED,
+	},
+};
+
+static const struct gpio_led_platform_data apx4devkit_led_data __initconst = {
+	.leds = apx4devkit_leds,
+	.num_leds = ARRAY_SIZE(apx4devkit_leds),
+};
+
+static const struct fec_platform_data mx28_fec_pdata __initconst = {
+	.phy = PHY_INTERFACE_MODE_RMII,
+};
+
+static const struct mxs_mmc_platform_data apx4devkit_mmc_pdata __initconst = {
+	.wp_gpio = -EINVAL,
+	.flags = SLOTF_4_BIT_CAPABLE,
+};
+
+static const struct i2c_board_info apx4devkit_i2c_boardinfo[] __initconst = {
+	{ I2C_BOARD_INFO("sgtl5000", 0x0a) }, /* ASoC */
+	{ I2C_BOARD_INFO("pcf8563", 0x51) }, /* RTC */
+};
+
+#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || \
+		defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
+static struct regulator_consumer_supply apx4devkit_audio_consumer_supplies[] = {
+	REGULATOR_SUPPLY("VDDA", "0-000a"),
+	REGULATOR_SUPPLY("VDDIO", "0-000a"),
+};
+
+static struct regulator_init_data apx4devkit_vdd_reg_init_data = {
+	.constraints	= {
+		.name	= "3V3",
+		.always_on = 1,
+	},
+	.consumer_supplies = apx4devkit_audio_consumer_supplies,
+	.num_consumer_supplies = ARRAY_SIZE(apx4devkit_audio_consumer_supplies),
+};
+
+static struct fixed_voltage_config apx4devkit_vdd_pdata = {
+	.supply_name	= "board-3V3",
+	.microvolts	= 3300000,
+	.gpio		= -EINVAL,
+	.enabled_at_boot = 1,
+	.init_data	= &apx4devkit_vdd_reg_init_data,
+};
+
+static struct platform_device apx4devkit_voltage_regulator = {
+	.name		= "reg-fixed-voltage",
+	.id		= -1,
+	.num_resources	= 0,
+	.dev		= {
+		.platform_data	= &apx4devkit_vdd_pdata,
+	},
+};
+
+static void __init apx4devkit_add_regulators(void)
+{
+	platform_device_register(&apx4devkit_voltage_regulator);
+}
+#else
+static void __init apx4devkit_add_regulators(void) {}
+#endif
+
+static const struct mxs_saif_platform_data
+			apx4devkit_mxs_saif_pdata[] __initconst = {
+	/* working on EXTMSTR0 mode (saif0 master, saif1 slave) */
+	{
+		.master_mode = 1,
+		.master_id = 0,
+	}, {
+		.master_mode = 0,
+		.master_id = 0,
+	},
+};
+
+static int apx4devkit_phy_fixup(struct phy_device *phy)
+{
+	phy->dev_flags |= MICREL_PHY_50MHZ_CLK;
+	return 0;
+}
+
+static void __init apx4devkit_init(void)
+{
+	mxs_iomux_setup_multiple_pads(apx4devkit_pads,
+			ARRAY_SIZE(apx4devkit_pads));
+
+	mx28_add_duart();
+	mx28_add_auart0();
+	mx28_add_auart1();
+	mx28_add_auart2();
+	mx28_add_auart3();
+
+	/*
+	 * Register fixup for the Micrel KS8031 PHY clock
+	 * (shares same ID with KS8051)
+	 */
+	phy_register_fixup_for_uid(PHY_ID_KS8051, MICREL_PHY_ID_MASK,
+			apx4devkit_phy_fixup);
+
+	mx28_add_fec(0, &mx28_fec_pdata);
+
+	mx28_add_mxs_mmc(0, &apx4devkit_mmc_pdata);
+
+	gpio_led_register_device(0, &apx4devkit_led_data);
+
+	mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
+	mx28_add_saif(0, &apx4devkit_mxs_saif_pdata[0]);
+	mx28_add_saif(1, &apx4devkit_mxs_saif_pdata[1]);
+
+	apx4devkit_add_regulators();
+
+	mx28_add_mxs_i2c(0);
+	i2c_register_board_info(0, apx4devkit_i2c_boardinfo,
+			ARRAY_SIZE(apx4devkit_i2c_boardinfo));
+
+	mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0, NULL, 0);
+}
+
+static void __init apx4devkit_timer_init(void)
+{
+	mx28_clocks_init();
+}
+
+static struct sys_timer apx4devkit_timer = {
+	.init	= apx4devkit_timer_init,
+};
+
+MACHINE_START(APX4DEVKIT, "Bluegiga APX4 Development Kit")
+	.map_io		= mx28_map_io,
+	.init_irq	= mx28_init_irq,
+	.timer		= &apx4devkit_timer,
+	.init_machine	= apx4devkit_init,
+	.restart	= mxs_restart,
+MACHINE_END

arch/arm/mach-mxs/mach-m28evk.c

@@ -247,18 +247,15 @@ static int __init m28evk_fec_get_mac(void)
 	u32 val;
 	const u32 *ocotp = mxs_get_ocotp();
 
-	if (!ocotp) {
-		pr_err("%s: timeout when reading fec mac from OCOTP\n",
-			__func__);
+	if (!ocotp)
 		return -ETIMEDOUT;
-	}
 
 	/*
 	 * OCOTP only stores the last 4 octets for each mac address,
 	 * so hard-code DENX OUI (C0:E5:4E) here.
 	 */
 	for (i = 0; i < 2; i++) {
-		val = ocotp[i * 4];
+		val = ocotp[i];
 		mx28_fec_pdata[i].mac[0] = 0xC0;
 		mx28_fec_pdata[i].mac[1] = 0xE5;
 		mx28_fec_pdata[i].mac[2] = 0x4E;

arch/arm/mach-mxs/mach-mx28evk.c

@@ -223,7 +223,6 @@ static const struct gpio_led_platform_data mx28evk_led_data __initconst = {
 /* fec */
 static void __init mx28evk_fec_reset(void)
 {
-	int ret;
 	struct clk *clk;
 
 	/* Enable fec phy clock */
@@ -231,32 +230,7 @@ static void __init mx28evk_fec_reset(void)
 	if (!IS_ERR(clk))
 		clk_prepare_enable(clk);
 
-	/* Power up fec phy */
-	ret = gpio_request(MX28EVK_FEC_PHY_POWER, "fec-phy-power");
-	if (ret) {
-		pr_err("Failed to request gpio fec-phy-%s: %d\n", "power", ret);
-		return;
-	}
-
-	ret = gpio_direction_output(MX28EVK_FEC_PHY_POWER, 0);
-	if (ret) {
-		pr_err("Failed to drive gpio fec-phy-%s: %d\n", "power", ret);
-		return;
-	}
-
-	/* Reset fec phy */
-	ret = gpio_request(MX28EVK_FEC_PHY_RESET, "fec-phy-reset");
-	if (ret) {
-		pr_err("Failed to request gpio fec-phy-%s: %d\n", "reset", ret);
-		return;
-	}
-
-	gpio_direction_output(MX28EVK_FEC_PHY_RESET, 0);
-	if (ret) {
-		pr_err("Failed to drive gpio fec-phy-%s: %d\n", "reset", ret);
-		return;
-	}
-
+	gpio_set_value(MX28EVK_FEC_PHY_RESET, 0);
 	mdelay(1);
 	gpio_set_value(MX28EVK_FEC_PHY_RESET, 1);
 }
@@ -278,14 +252,14 @@ static int __init mx28evk_fec_get_mac(void)
 	const u32 *ocotp = mxs_get_ocotp();
 
 	if (!ocotp)
-		goto error;
+		return -ETIMEDOUT;
 
 	/*
 	 * OCOTP only stores the last 4 octets for each mac address,
 	 * so hard-code Freescale OUI (00:04:9f) here.
 	 */
 	for (i = 0; i < 2; i++) {
-		val = ocotp[i * 4];
+		val = ocotp[i];
 		mx28_fec_pdata[i].mac[0] = 0x00;
 		mx28_fec_pdata[i].mac[1] = 0x04;
 		mx28_fec_pdata[i].mac[2] = 0x9f;
@@ -295,10 +269,6 @@ static int __init mx28evk_fec_get_mac(void)
 	}
 
 	return 0;
-
-error:
-	pr_err("%s: timeout when reading fec mac from OCOTP\n", __func__);
-	return -ETIMEDOUT;
 }
 
 /*
@@ -417,9 +387,14 @@ static void __init mx28evk_add_regulators(void)
 static void __init mx28evk_add_regulators(void) {}
 #endif
 
-static struct gpio mx28evk_lcd_gpios[] = {
+static const struct gpio mx28evk_gpios[] __initconst = {
 	{ MX28EVK_LCD_ENABLE, GPIOF_OUT_INIT_HIGH, "lcd-enable" },
 	{ MX28EVK_BL_ENABLE, GPIOF_OUT_INIT_HIGH, "bl-enable" },
+	{ MX28EVK_FLEXCAN_SWITCH, GPIOF_DIR_OUT, "flexcan-switch" },
+	{ MX28EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW, "mmc0-slot-power" },
+	{ MX28EVK_MMC1_SLOT_POWER, GPIOF_OUT_INIT_LOW, "mmc1-slot-power" },
+	{ MX28EVK_FEC_PHY_POWER, GPIOF_OUT_INIT_LOW, "fec-phy-power" },
+	{ MX28EVK_FEC_PHY_RESET, GPIOF_DIR_OUT, "fec-phy-reset" },
 };
 
 static const struct mxs_saif_platform_data
@@ -447,25 +422,18 @@ static void __init mx28evk_init(void)
 	if (mx28evk_fec_get_mac())
 		pr_warn("%s: failed on fec mac setup\n", __func__);
 
+	ret = gpio_request_array(mx28evk_gpios, ARRAY_SIZE(mx28evk_gpios));
+	if (ret)
+		pr_err("One or more GPIOs failed to be requested: %d\n", ret);
+
 	mx28evk_fec_reset();
 	mx28_add_fec(0, &mx28_fec_pdata[0]);
 	mx28_add_fec(1, &mx28_fec_pdata[1]);
 
-	ret = gpio_request_one(MX28EVK_FLEXCAN_SWITCH, GPIOF_DIR_OUT,
-				"flexcan-switch");
-	if (ret) {
-		pr_err("failed to request gpio flexcan-switch: %d\n", ret);
-	} else {
-		mx28_add_flexcan(0, &mx28evk_flexcan_pdata[0]);
-		mx28_add_flexcan(1, &mx28evk_flexcan_pdata[1]);
-	}
+	mx28_add_flexcan(0, &mx28evk_flexcan_pdata[0]);
+	mx28_add_flexcan(1, &mx28evk_flexcan_pdata[1]);
 
-	ret = gpio_request_array(mx28evk_lcd_gpios,
-				 ARRAY_SIZE(mx28evk_lcd_gpios));
-	if (ret)
-		pr_warn("failed to request gpio pins for lcd: %d\n", ret);
-	else
-		mx28_add_mxsfb(&mx28evk_mxsfb_pdata);
+	mx28_add_mxsfb(&mx28evk_mxsfb_pdata);
 
 	mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
 	mx28_add_saif(0, &mx28evk_mxs_saif_pdata[0]);
@@ -480,20 +448,8 @@ static void __init mx28evk_init(void)
 	mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0,
 			NULL, 0);
 
-	/* power on mmc slot by writing 0 to the gpio */
-	ret = gpio_request_one(MX28EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW,
-			       "mmc0-slot-power");
-	if (ret)
-		pr_warn("failed to request gpio mmc0-slot-power: %d\n", ret);
-	else
-		mx28_add_mxs_mmc(0, &mx28evk_mmc_pdata[0]);
-
-	ret = gpio_request_one(MX28EVK_MMC1_SLOT_POWER, GPIOF_OUT_INIT_LOW,
-			       "mmc1-slot-power");
-	if (ret)
-		pr_warn("failed to request gpio mmc1-slot-power: %d\n", ret);
-	else
-		mx28_add_mxs_mmc(1, &mx28evk_mmc_pdata[1]);
+	mx28_add_mxs_mmc(0, &mx28evk_mmc_pdata[0]);
+	mx28_add_mxs_mmc(1, &mx28evk_mmc_pdata[1]);
 
 	mx28_add_rtc_stmp3xxx();